HP-ICF-GPPCV2-MIB DEFINITIONS ::= BEGIN IMPORTS MODULE-IDENTITY, OBJECT-TYPE, Integer32 FROM SNMPv2-SMI MODULE-COMPLIANCE, OBJECT-GROUP FROM SNMPv2-CONF TEXTUAL-CONVENTION, RowStatus FROM SNMPv2-TC SnmpAdminString FROM SNMP-FRAMEWORK-MIB PortList FROM Q-BRIDGE-MIB hpSwitch FROM HP-ICF-OID; hpicfGppcv2MIB MODULE-IDENTITY LAST-UPDATED "201011120000Z" -- November 12, 2010 ORGANIZATION "HP Networking" CONTACT-INFO "Hewlett Packard Company 8000 Foothills Blvd. Roseville, CA 95747" DESCRIPTION "This MIB module is for HP proprietary General Purpose Packet Control Version 2 (Gppcv2)" REVISION "201011120000Z" -- November 12, 2010 DESCRIPTION "Added hpicfGppcv2AcIngressTunnelList and hpicfGppcv2AcEgressTunnelList to HpicfGppcv2AppControlEntry and hpicfGppcv2MIBCompliance/hpicfGppcv2Group" REVISION "201003012201Z" DESCRIPTION "Initial revision." ::= { hpSwitch 61 } -- *********************************************** -- TEXTUAL Conventions -- *********************************************** HpicfGppcv2PolicyName ::= TEXTUAL-CONVENTION DISPLAY-HINT "70a" STATUS current DESCRIPTION "Type definition for the name of a policy. A policy name is a printable string consisting of up to 64 characters from the ASCII character set. The policy name is case sensitive" SYNTAX OCTET STRING (SIZE(1..70)) HpicfGppcv2PolicyType ::= TEXTUAL-CONVENTION STATUS current DESCRIPTION "Type of the policy. A policy of type 'aclIpv4' indicates that the policy is an IPv4 Access Control List, an ACL that filters packets based on source IPv4 address and subnet, destination IPv4 address and subnet, and protocol amongst other packet information. A policy of type 'aclIpv6' indicates that the policy is an IPv6 Access Control List, an ACL that filters packets based on source IPv6 address and subnet, destination IPv6 address and subnet, and protocol amongst other packet information. A policy of type 'classifierClassIpv4' indicates that the policy is an IPv4 Classifier class which specifies packets to be compared against the specified source IPv4 address and subnet, destination and subnet, protocol, etc. A policy of type 'classifierClassIpv6' indicates that the policy is an IPv6 Classifier class which specifies packets to be compared against the specified source IPv6 address and subnet, destination and subnet, protocol, etc. A policy type of 'classifierPolicy' indicates that the policy will perform Quality of Service/mirror actions on packets that match statements in the policy's classes. A policy type of 'connectionRateFilterIpv4' indicates that the policy is an IPv4 Connection Rate Filter, a list that specifies packets to be filtered or ignored based on source IPv4 address and subnet and protocol." SYNTAX INTEGER { aclIpv4(1), aclIpv6(2), classifierClassIpv4(3), classifierClassIpv6(4), classifierPolicy(5), connectionRateFilterIpv4(6)} HpicfGppcv2LastErrorCode ::= TEXTUAL-CONVENTION STATUS current DESCRIPTION "Error code of the last error that occurred. A non-zero value indicates that the last operation performed by this instance of the application or on the named policy did not succeed." SYNTAX INTEGER { noError(0), gppcv2GenericError(1), gppcv2LengthError(2), gppcv2NameError(3), gppcv2ParameterError(4), gppcv2NotImplemented(5), gppcv2MallocError(6), gppcv2TooManyApps(7), gppcv2TooManyPolicies(8), gppcv2AlreadyReserved(9), gppcv2EntryExists(10), gppcv2PlatformError(11), gppcv2AppUsingPolicy(12), gppcv2InvalidPolicyType(13), gppcv2NotReserved(14), gppcv2NoPolicy(15), gppcv2PolicyNotActive(16), gppcv2PolicyHasRules(17), gppcv2RuleExists(18), gppcv2ReleaseRules(19), gppcv2ReleaseAppCtrlEntry(20), gppcv2CfgError(50), gppcv2AceCreateError(70), gppcv2AceConflictingRuleError(71), gppcv2AceDuplicateError(72), gppcv2AceDuplicateSequenceNumError(73), gppcv2AceCfgLimitReachedError(74), gppcv2AceNotFoundError(75), gppcv2AclDuplcateNameError(76), gppcv2AclMaxSequenceNumError(77), gppcv2AclMgmtVlanConflictError(78), gppcv2AclApplyError(79), gppcv2AclCreateError(80), gppcv2AclCfgLimitReachedError(81), gppcv2AclNotFoundError(82), gppcv2AclNotAppliedVlanError(83), gppcv2AclNotAppliedPortError(84), gppcv2InvalidTypeForCrfError(85), gppcv2AclResequenceLimitError(86), gppcv2ClassMaxSequenceNumError(87), gppcv2ClassNotFoundError(88), gppcv2ClassCreateError(89), gppcv2ClassEntryCfgLimitReachedError(90), gppcv2ClassListCfgLimitReachedError(91), gppcv2ClassDuplicateNameError(92), gppcv2ClassEntryAddError(93), gppcv2ClassEntryNotFoundError(94), gppcv2ClassConflictingRuleError(95), gppcv2PolicyNotFoundError(96), gppcv2PolicyNameConflictError(97), gppcv2PolicyNotAppliedError(98), gppcv2PolicyCreateError(99), gppcv2PolicyAddClassError(100), gppcv2PolicyDeleteClassError(101), gppcv2PolicyClassNotFoundError(102), gppcv2PolicyDeleteError(103), gppcv2PolicyApplyError(104), gppcv2PolicyIsAppliedCannotDeleteError(105), gppcv2PolicyDuplicateClassError(106), gppcv2PolicyClassifiedVlanOnVlanError(107), gppcv2PolicyCfgLimitReachedError(108), gppcv2PolicyApplyDetailedError(109)} -- *********************************************** -- Start of MIB Objects -- *********************************************** hpicfGppcv2Conformance OBJECT IDENTIFIER ::= { hpicfGppcv2MIB 1 } -- *********************************************** -- Gppcv2 application control table -- *********************************************** hpicfGppcv2AppControlTable OBJECT-TYPE SYNTAX SEQUENCE OF HpicfGppcv2AppControlEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "The application control table. This keeps track of the applications that use Gppcv2, the policies set by these applications, and information on where/when/how to apply these policies. This information includes the interfaces and VLANs where the policy should be applied, whether it should be applied at ingress or egress, and when it should expire. The following limitation is in place: there can be no more than one policy action per SNMP pdu." ::= { hpicfGppcv2MIB 2 } hpicfGppcv2AppControlEntry OBJECT-TYPE SYNTAX HpicfGppcv2AppControlEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "An entry in the application control table." INDEX { hpicfGppcv2AcAppName, hpicfGppcv2AcAppInstance, hpicfGppcv2AcPolicyType, hpicfGppcv2AcPolicyName } ::= { hpicfGppcv2AppControlTable 1 } HpicfGppcv2AppControlEntry ::= SEQUENCE { hpicfGppcv2AcAppName SnmpAdminString, hpicfGppcv2AcAppInstance SnmpAdminString, hpicfGppcv2AcPolicyType HpicfGppcv2PolicyType, hpicfGppcv2AcPolicyName HpicfGppcv2PolicyName, hpicfGppcv2AcIngressIfList PortList, hpicfGppcv2AcIngressVIDList OCTET STRING, hpicfGppcv2AcEgressIfList PortList, hpicfGppcv2AcEgressVIDList OCTET STRING, hpicfGppcv2AcVIDList OCTET STRING, hpicfGppcv2AcExpPolicy INTEGER, hpicfGppcv2AcExpString OCTET STRING, hpicfGppcv2AcLastErrorCode INTEGER, hpicfGppcv2AcLastErrorString SnmpAdminString, hpicfGppcv2AcRowAdminStatus INTEGER, hpicfGppcv2AcRowStatus RowStatus, hpicfGppcv2AcIngressTunnelList OCTET STRING, hpicfGppcv2AcEgressTunnelList OCTET STRING } hpicfGppcv2AcAppName OBJECT-TYPE SYNTAX SnmpAdminString (SIZE(1..16)) MAX-ACCESS not-accessible STATUS current DESCRIPTION "Name of the application that last modified this row. All applications of the same type should use the same name and should use different instance identifiers to identify themselves uniquely. This is a printable string up to 16 bytes in size." ::= { hpicfGppcv2AppControlEntry 1 } hpicfGppcv2AcAppInstance OBJECT-TYPE SYNTAX SnmpAdminString (SIZE(1..16)) MAX-ACCESS not-accessible STATUS current DESCRIPTION "Instance identifier of the application. This is used to distinguish between different instances of the same application. This is a printable string up to 16 bytes in size." ::= { hpicfGppcv2AppControlEntry 2 } hpicfGppcv2AcPolicyType OBJECT-TYPE SYNTAX HpicfGppcv2PolicyType MAX-ACCESS not-accessible STATUS current DESCRIPTION "Type of the policy, used to distinguish policies with the same name." ::= { hpicfGppcv2AppControlEntry 3 } hpicfGppcv2AcPolicyName OBJECT-TYPE SYNTAX HpicfGppcv2PolicyName MAX-ACCESS not-accessible STATUS current DESCRIPTION "Name of the policy. Each policy is uniquely identified by its name. It is possible to apply the same policy in different manners to different interfaces and VLANs. This is a printable string up to 64 characters in size and case sensitive." ::= { hpicfGppcv2AppControlEntry 4 } hpicfGppcv2AcIngressIfList OBJECT-TYPE SYNTAX PortList MAX-ACCESS read-create STATUS current DESCRIPTION "List of interfaces to which this policy applies at ingress." ::= { hpicfGppcv2AppControlEntry 5 } hpicfGppcv2AcIngressVIDList OBJECT-TYPE SYNTAX OCTET STRING (SIZE(0..512)) MAX-ACCESS read-create STATUS current DESCRIPTION "A string of octets containing one bit per Vlan-Id for VLANS with vlan index values of 0 through 4096. The first octet corresponds to VLANs with vlan index values of 0 through 7, the second octet to VLANs 8 through 15, etc. The most significant bit of each octet corresponds to the lowest vlan index value in that octet. For each VLAN that this policy should apply to at ingress, the corresponding bit is set to '1'." ::= { hpicfGppcv2AppControlEntry 6 } hpicfGppcv2AcEgressIfList OBJECT-TYPE SYNTAX PortList MAX-ACCESS read-create STATUS current DESCRIPTION "List of interfaces to which this policy applies at egress." ::= { hpicfGppcv2AppControlEntry 7 } hpicfGppcv2AcEgressVIDList OBJECT-TYPE SYNTAX OCTET STRING (SIZE(0..512)) MAX-ACCESS read-create STATUS current DESCRIPTION "A string of octets containing one bit per Vlan-Id for VLANS with vlan index values of 0 through 4096. The first octet corresponds to VLANs with vlan index values of 0 through 7, the second octet to VLANs 8 through 15, etc. The most significant bit of each octet corresponds to the lowest vlan index value in that octet. For each VLAN that this policy should apply to at egress, the corresponding bit is set to '1'." ::= { hpicfGppcv2AppControlEntry 8 } hpicfGppcv2AcVIDList OBJECT-TYPE SYNTAX OCTET STRING (SIZE(0..512)) MAX-ACCESS read-create STATUS current DESCRIPTION "A string of octets containing one bit per Vlan-Id for VLANS with vlan index values of 0 through 4096. The first octet corresponds to VLANs with vlan index values of 0 through 7, the second octet to VLANs 8 through 15, etc. The most significant bit of each octet corresponds to the lowest vlan index value in that octet. For each VLAN that this policy should apply to as a VLAN ACL, the corresponding bit is set to '1'." ::= { hpicfGppcv2AppControlEntry 9 } hpicfGppcv2AcExpPolicy OBJECT-TYPE SYNTAX INTEGER { permanent(1) } MAX-ACCESS read-create STATUS current DESCRIPTION "Expiration policy. This indicates whether a policy should expire automatically. 'permanent' means a policy should never expire automatically." ::= { hpicfGppcv2AppControlEntry 10 } hpicfGppcv2AcExpString OBJECT-TYPE SYNTAX OCTET STRING (SIZE(0..24)) MAX-ACCESS read-create STATUS current DESCRIPTION "Expiration string. This is used in conjunction with hpicfGppcv2AcExpPolicy to indicate when a policy should expire automatically. The value stored in this object is interpreted differently for different expiration policies. When the expiration policy is 'permanent', this value is ignored." ::= { hpicfGppcv2AppControlEntry 11 } hpicfGppcv2AcLastErrorCode OBJECT-TYPE SYNTAX HpicfGppcv2LastErrorCode MAX-ACCESS read-only STATUS current DESCRIPTION "Error code of the last error that occurred. A non-zero value indicates that the last operation performed by this instance of the application on the named policy did not succeed. A detailed description of the error is available in hpicfGppcv2AcLastErrorString." ::= { hpicfGppcv2AppControlEntry 12 } hpicfGppcv2AcLastErrorString OBJECT-TYPE SYNTAX SnmpAdminString (SIZE(0..255)) MAX-ACCESS read-only STATUS current DESCRIPTION "Description of the last error that occurred. This is a printable ASCII string that describes the error in some detail." ::= { hpicfGppcv2AppControlEntry 13 } hpicfGppcv2AcRowAdminStatus OBJECT-TYPE SYNTAX INTEGER { enabled(1), disabled(2) } MAX-ACCESS read-create STATUS current DESCRIPTION "Administrative status of this row. The named policy in this row is applied to the interfaces and/or VLANs by this instance of the application only when the administrative status is enabled. This is the main on/off switch for the row. The row status must be active for this switch to have an effect." ::= { hpicfGppcv2AppControlEntry 14 } hpicfGppcv2AcRowStatus OBJECT-TYPE SYNTAX RowStatus MAX-ACCESS read-create STATUS current DESCRIPTION "Status of this row. Row status must be active, and the admin status (see hpicfGppcv2AcRowAdminStatus) must be enabled for this row to be activated." ::= { hpicfGppcv2AppControlEntry 15 } hpicfGppcv2AcIngressTunnelList OBJECT-TYPE SYNTAX OCTET STRING (SIZE(0..256)) MAX-ACCESS read-create STATUS current DESCRIPTION "A string of octets containing one bit per tunnel-id for tunnels with tunnel values of 0 through 2047. The first octet corresponds to tunnel with values of 0 through 7, the second octet with values from 8 through 15, etc. The most significant bit of each octet corresponds to the lowest tunnel value in that octet. For each tunnel that this policy should apply to at ingress, the corresponding bit is set to '1'." ::= { hpicfGppcv2AppControlEntry 16} hpicfGppcv2AcEgressTunnelList OBJECT-TYPE SYNTAX OCTET STRING (SIZE(0..256)) MAX-ACCESS read-create STATUS current DESCRIPTION "A string of octets containing one bit per tunnel-id for tunnels with tunnel values of 0 through 2047. The first octet corresponds to tunnel with values of 0 through 7, the second octet with values from 8 through 15, etc. The most significant bit of each octet corresponds to the lowest tunnel value in that octet. For each tunnel that this policy should apply to at egress, the corresponding bit is set to '1'." ::= { hpicfGppcv2AppControlEntry 17 } -- *********************************************** -- Gppcv2 named policy table -- *********************************************** hpicfGppcv2NamedPolicyTable OBJECT-TYPE SYNTAX SEQUENCE OF HpicfGppcv2NamedPolicyEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "The named policy table. This table lists the name and type of all policies that are applied via Gppcv2. The following limitation is in place: there can be no more than one policy action per SNMP pdu." ::= { hpicfGppcv2MIB 3 } hpicfGppcv2NamedPolicyEntry OBJECT-TYPE SYNTAX HpicfGppcv2NamedPolicyEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "An entry in the named policy table." INDEX { hpicfGppcv2NpPolicyName, hpicfGppcv2NpPolicyType } ::= { hpicfGppcv2NamedPolicyTable 1 } HpicfGppcv2NamedPolicyEntry ::= SEQUENCE { hpicfGppcv2NpPolicyName HpicfGppcv2PolicyName, hpicfGppcv2NpPolicyType HpicfGppcv2PolicyType, hpicfGppcv2NpSubType INTEGER, hpicfGppcv2NpReseqStart Integer32, hpicfGppcv2NpReseqIncr Integer32, hpicfGppcv2NpLastSeqNo Integer32, hpicfGppcv2NpLastErrorCode INTEGER, hpicfGppcv2NpLastErrorString SnmpAdminString, hpicfGppcv2NpRowStatus RowStatus } hpicfGppcv2NpPolicyName OBJECT-TYPE SYNTAX HpicfGppcv2PolicyName MAX-ACCESS not-accessible STATUS current DESCRIPTION "Name of the policy. The name of a policy is its unique identification. It is a printable string in ASCII characters. It can be up to 64 characters in length and it case sensitive" ::= { hpicfGppcv2NamedPolicyEntry 1 } hpicfGppcv2NpPolicyType OBJECT-TYPE SYNTAX HpicfGppcv2PolicyType MAX-ACCESS not-accessible STATUS current DESCRIPTION "Type of the policy as defined in the TEXTUAL-CONVENTION" ::= { hpicfGppcv2NamedPolicyEntry 2 } hpicfGppcv2NpSubType OBJECT-TYPE SYNTAX INTEGER { subtypeNone(1), aclStandard(2), aclExtended(3), aclConnectionRateFilter(4), aclIdm(5), aclExtendedIpv6(6), policyQos(7), policyMirror(8), policyPbr(9) } MAX-ACCESS read-create STATUS current DESCRIPTION "Subtype of the policy. A subtype of 'aclStandard' indicates that the policy is a standard Access Control List. The policy is used to permit or deny packets based on source IPv4 address and subnet only. A subtype of 'aclExtended' indicates that the policy is an extended Access Control List, an ACL that filters packets based on source IPv4 address and subnet, destination IPv4 address and subnet, and protocol amongst other packet information. A subtype of 'aclConnectionRateFilter' indicates that the policy is a connection-rate-filter Access Control List, similar to an ACL-extended. A subtype of 'aclIdm' indicates that the policy is a Identity Driven Management ACL used to filter traffic based on the source MAC address, protocol and destination IP information of a packet. A subtype of 'aclExtendedIpv6' indicates that the policy is an extended Access Control List, an ACL that filters packets based on source IPv6 address and subnet, destination IPv6 address and subnet, and protocol amongst other packet information. A subype of 'policyQos' indicates that the policy will perform Quality of Service actions on packets that match statements in the policy's classes. A subtype of 'policyMirror' indicates that the policy will perform mirror actions on packets that match statements in the policy's classes. A subtype of 'policyPbr' indicates that the policy will perform Policy Based Routing actions on packets that match statements in the policy's classes." ::= { hpicfGppcv2NamedPolicyEntry 3 } hpicfGppcv2NpReseqStart OBJECT-TYPE SYNTAX Integer32 (0..2147483647) MAX-ACCESS read-create STATUS current DESCRIPTION "Specifies the starting sequence number for resequence." ::= { hpicfGppcv2NamedPolicyEntry 4 } hpicfGppcv2NpReseqIncr OBJECT-TYPE SYNTAX Integer32 (0..2147483647) MAX-ACCESS read-create STATUS current DESCRIPTION "Specifies the increment value for resequence." ::= { hpicfGppcv2NamedPolicyEntry 5 } hpicfGppcv2NpLastSeqNo OBJECT-TYPE SYNTAX Integer32 (0..2147483647) MAX-ACCESS read-only STATUS current DESCRIPTION "Contains the highest valid sequence number for this policy entry at any point of time." ::= { hpicfGppcv2NamedPolicyEntry 6 } hpicfGppcv2NpLastErrorCode OBJECT-TYPE SYNTAX HpicfGppcv2LastErrorCode MAX-ACCESS read-only STATUS current DESCRIPTION "Error code of the last error that occurred. A non-zero value indicates that the last operation performed on the ruleEntry of this policy did not succeed. A detailed description of the error is available in hpicfGppcv2NpLastErrorString." ::= { hpicfGppcv2NamedPolicyEntry 7 } hpicfGppcv2NpLastErrorString OBJECT-TYPE SYNTAX SnmpAdminString (SIZE(0..255)) MAX-ACCESS read-only STATUS current DESCRIPTION "Description of the last error that occurred. This is a printable ASCII string that describes the error in some detail." ::= { hpicfGppcv2NamedPolicyEntry 8 } hpicfGppcv2NpRowStatus OBJECT-TYPE SYNTAX RowStatus MAX-ACCESS read-create STATUS current DESCRIPTION "Status of this row. The named policy must be active before rules can be added to it or removed from it. A newly created policy will remain in notReady state until it is given a valid policy type (see hpicfGppcv2NpPolicyType). A row in the named policy table can not be deleted if the named policy is referenced by a row in the application control table. The application control entries that refer to this row must be deleted before this row can be deleted." ::= { hpicfGppcv2NamedPolicyEntry 9 } -- *********************************************** -- Gppcv2 policy rules table -- *********************************************** hpicfGppcv2PolicyRulesTable OBJECT-TYPE SYNTAX SEQUENCE OF HpicfGppcv2PolicyRulesEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "The policy rules table. A policy can consist of multiple rules. All of the rules of a policy are listed in this table. Each rule consists of a string and a numeric identifier - the rule id. The following limitation is in place: there can be no more than one policy action per SNMP pdu." ::= { hpicfGppcv2MIB 4 } hpicfGppcv2PolicyRulesEntry OBJECT-TYPE SYNTAX HpicfGppcv2PolicyRulesEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "An entry in the policy rules table." INDEX { hpicfGppcv2NpPolicyName, hpicfGppcv2NpPolicyType, hpicfGppcv2PrRuleId } ::= { hpicfGppcv2PolicyRulesTable 1 } HpicfGppcv2PolicyRulesEntry ::= SEQUENCE { hpicfGppcv2PrRuleId Integer32, hpicfGppcv2PrPolicyRule OCTET STRING, hpicfGppcv2PrRemark OCTET STRING, hpicfGppcv2PrRowStatus RowStatus } hpicfGppcv2PrRuleId OBJECT-TYPE SYNTAX Integer32 (1..2147483647) MAX-ACCESS not-accessible STATUS current DESCRIPTION "Numeric identifier of the rule. The rules in a policy are processed sequentially in increasing order of their rule ids. These numeric ids are generated by the application that creates the policy. Rules within a policy have unique rule IDs." ::= { hpicfGppcv2PolicyRulesEntry 1 } hpicfGppcv2PrPolicyRule OBJECT-TYPE SYNTAX OCTET STRING (SIZE(0..512)) MAX-ACCESS read-create STATUS current DESCRIPTION "Rule string. This is a string that represents one rule in the policy. A policy can consist of one or many rules. For details on the format of the rule string please see: http://h17007.www1.hp.com" ::= { hpicfGppcv2PolicyRulesEntry 2 } hpicfGppcv2PrRemark OBJECT-TYPE SYNTAX OCTET STRING (SIZE(0..128)) MAX-ACCESS read-create STATUS current DESCRIPTION "Remark string. This is a descriptive text string for a policy rule entry. For details on the format of the rule string please see: http://h17007.www1.hp.com" ::= { hpicfGppcv2PolicyRulesEntry 3 } hpicfGppcv2PrRowStatus OBJECT-TYPE SYNTAX RowStatus MAX-ACCESS read-create STATUS current DESCRIPTION "Status of this row. A rule must have an active row status in order to take effect. Only active rules within the named policy are applied when an application applies the policy. It is possible to use this row status as an on/off switch for enabling or disabling selected rules within a policy. A newly created rule will remain in notReady state until it is given a valid rule string (see hpicfGppcv2PrPolicyRule)." ::= { hpicfGppcv2PolicyRulesEntry 4 } -- ********************************************************************** -- Conformance Information -- ********************************************************************** hpicfGppcv2MIBCompliances OBJECT IDENTIFIER ::= { hpicfGppcv2Conformance 1 } hpicfGppcv2MIBGroups OBJECT IDENTIFIER ::= { hpicfGppcv2Conformance 2 } hpicfGppcv2MIBCompliance MODULE-COMPLIANCE STATUS current DESCRIPTION "The compliance statement for HP routers implementing the HP-ICF-Gppcv2-MIB." MODULE MANDATORY-GROUPS { hpicfGppcv2Group } GROUP hpicfGppcv2Group DESCRIPTION "Support for this group is required for HP routers that implement Gppcv2." ::= { hpicfGppcv2MIBCompliances 1 } hpicfGppcv2Group OBJECT-GROUP OBJECTS { hpicfGppcv2AcIngressIfList, hpicfGppcv2AcIngressVIDList, hpicfGppcv2AcEgressIfList, hpicfGppcv2AcEgressVIDList, hpicfGppcv2AcVIDList, hpicfGppcv2AcExpPolicy, hpicfGppcv2AcExpString, hpicfGppcv2AcLastErrorCode, hpicfGppcv2AcLastErrorString, hpicfGppcv2AcRowAdminStatus, hpicfGppcv2AcRowStatus, hpicfGppcv2NpSubType, hpicfGppcv2NpReseqStart, hpicfGppcv2NpReseqIncr, hpicfGppcv2NpLastSeqNo, hpicfGppcv2NpLastErrorCode, hpicfGppcv2NpLastErrorString, hpicfGppcv2NpRowStatus, hpicfGppcv2PrPolicyRule, hpicfGppcv2PrRemark, hpicfGppcv2PrRowStatus, hpicfGppcv2AcIngressTunnelList, hpicfGppcv2AcEgressTunnelList } STATUS current DESCRIPTION "A collection of HP proprietary objects to support Gppcv2." ::= { hpicfGppcv2MIBGroups 1 } END