-- $Log: E5-110-MIB.mib $ -- Revision 1.43 2011/01/25 13:33:29 cylien -- Revision 1.42 2010/11/12 06:27:45 DavidGong -- Revision 1.41 2010/10/18 06:23:51 cylien -- Revision 1.40 2010/09/08 07:07:27 Alex.Shih -- Revision 1.39 2010/09/01 06:56:00 cylien -- Revision 1.38 2010/08/27 08:04:37 Alex.Shih -- Revision 1.37 2010/08/24 11:29:14 davidgong -- Revision 1.36 2010/08/23 10:00:23 davidgong -- Revision 1.35 2010/08/19 08:12:03 Alex.Shih -- Revision 1.34 2010/08/19 06:41:33 davidgong -- Revision 1.33 2010/08/18 06:54:57 davidgong -- Revision 1.32 2010/07/21 03:30:35 Alex.Shih -- Revision 1.31 2010/07/09 11:08:59 Alex.Shih -- Revision 1.29 2010/05/04 10:02:46 cylien -- Revision 1.28 2010/04/23 10:46:21 maverick -- Revision 1.27 2010/04/23 09:14:33 Ives -- Revision 1.26 2010/04/23 08:27:24 cylien -- Revision 1.25 2010/03/29 02:05:57 maverick -- Revision 1.24 2009/12/03 10:55:05 maverick -- Revision 1.23 2009/11/30 01:14:34 maverick -- Revision 1.22 2009/11/27 13:19:32 maverick -- Revision 1.21 2009/11/26 13:06:53 maverick -- add comment to obsoleted mib entries, mibble checked -- Revision 1.20 2009/11/23 06:51:50 maverick -- Revision 1.19 2009/11/06 02:10:37 maverick -- remove cfm, change atmqos to ipqos -- Revision 1.18 2009/10/26 02:39:01 maverick -- Revision 1.17 2009/10/19 10:32:53 maverick -- Revision 1.16 2009/09/16 02:55:29 niceguy -- Revision 1.15 2009/09/15 05:51:27 maverick -- Revision 1.14 2009/09/04 11:06:57 maverick -- Revision 1.13 2009/09/01 01:32:32 maverick -- Revision 1.12 2009/06/03 08:43:22 niceguy -- Revision 1.11 2009/05/08 10:18:25 niceguy -- Revision 1.10 2009/03/23 11:53:55 niceguy -- Revision 1.9 2009/03/18 02:16:23 niceguy -- Revision 1.8 2009/03/17 09:43:04 niceguy -- Revision 1.7 2009/03/17 08:05:06 niceguy -- Revision 1.6 2009/03/12 11:01:04 niceguy -- Revision 1.5 2009/03/12 03:32:03 niceguy -- Revision 1.4 2009/03/10 11:02:50 niceguy -- Revision 1.3 2009/03/09 00:58:46 niceguy -- Revision 1.2 2008/11/12 08:19:33 kenny -- Revision 1.1 2008/07/11 09:36:12 maverick -- Initial revision -- Revision 1.8 2008/06/30 07:43:20 maverick -- Revision 1.7 2008/04/28 02:29:16 maverick -- Revision 1.6 2008/03/07 07:56:43 kenny -- Revision 1.5 2007/12/14 10:00:11 niceguy -- Revision 1.4 2007/12/14 02:42:41 niceguy -- Revision 1.3 2007/12/06 02:03:04 kenny -- Revision 1.2 2007/12/03 01:54:35 niceguy -- Revision 1.1 2007/12/03 01:45:30 niceguy -- Initial revision -- Initial revision E5-110-MIB DEFINITIONS ::= BEGIN IMPORTS enterprises FROM RFC1155-SMI OBJECT-TYPE, Counter32, Gauge32, Unsigned32, Counter64, IpAddress, TimeTicks, NOTIFICATION-TYPE FROM SNMPv2-SMI DisplayString, PhysAddress, ifIndex FROM RFC1213-MIB RowStatus, TEXTUAL-CONVENTION FROM SNMPv2-TC VlanIndex, PortList, dot1qVlanIndex FROM Q-BRIDGE-MIB dot1dTrafficClass FROM P-BRIDGE-MIB MacAddress, Timeout, BridgeId, dot1dBasePort FROM BRIDGE-MIB; -- dot1agCfmMdMdLevel, dot1agCfmVlanPrimaryVid, dot1agCfmMepIdentifier -- FROM IEEE8021-CFMD8-MIB; calixNetworks OBJECT IDENTIFIER ::= { enterprises 6321 } calixRegistrations OBJECT IDENTIFIER ::= { calixNetworks 1 } calixProducts OBJECT IDENTIFIER ::= { calixRegistrations 2 } e5x100 OBJECT IDENTIFIER ::= { calixProducts 3 } e5x110 OBJECT IDENTIFIER ::= { e5x100 1 } alarmconf OBJECT IDENTIFIER ::= { e5x110 2 } diagnostic OBJECT IDENTIFIER ::= { e5x110 4 } multicast OBJECT IDENTIFIER ::= { e5x110 7 } port OBJECT IDENTIFIER ::= { e5x110 8 } switch OBJECT IDENTIFIER ::= { e5x110 10 } sys OBJECT IDENTIFIER ::= { e5x110 11 } trap OBJECT IDENTIFIER ::= { e5x110 12 } statistics OBJECT IDENTIFIER ::= { e5x110 13 } clear OBJECT IDENTIFIER ::= { e5x110 14 } aesSeriesCommon OBJECT IDENTIFIER ::= { e5x110 97 } iesSeriesCommon OBJECT IDENTIFIER ::= { e5x110 98 } accessSwitchCommonATM OBJECT IDENTIFIER ::= { e5x110 99 } ---------------------------------------- -- alarmconf ---------------------------------------- alarmOps OBJECT-TYPE SYNTAX INTEGER MAX-ACCESS read-write STATUS current DESCRIPTION "The manager sets the corresponding bit value to 1 to start the operation and the agent clears the object to zero when the operation is successfully completed. The various bit positions are: BIT 1: clear BIT 2: cutoff" ::= { alarmconf 1 } -- Alarm Conf Table alarmConfTable OBJECT-TYPE SYNTAX SEQUENCE OF AlarmConfEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "This table includes alarm configuration." ::= { alarmconf 2 } alarmConfEntry OBJECT-TYPE SYNTAX AlarmConfEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "An entry in alarmConfTable." INDEX { alarmConfId } ::= { alarmConfTable 1 } AlarmConfEntry ::= SEQUENCE { alarmConfId INTEGER, alarmConfFacility INTEGER, alarmConfTarget INTEGER, alarmConfSeverity INTEGER, alarmConfClearable INTEGER } alarmConfId OBJECT-TYPE SYNTAX INTEGER MAX-ACCESS read-only STATUS current DESCRIPTION " 5000:adslLine_up 5001:adslLine_down 5002:adslPerf_lol_thresh 5003:adslPerf_lof_thresh 5004:adslPerf_los_thresh 5005:adslPerf_lop_thresh 5006:adslPerf_es_thresh 5007:adslPerf_ses_thresh 5008:adslPerf_uas_thresh 5009:adslAtuc_loftrap 5010:adslAtuc_lostrap 5011:adslAtur_loftrap 5012:adslAtur_lostrap 5013:adslAtur_lprtrap 5014:ad_dhcp_rt_full 5015:ad_dhcp_dm_conflict 5016:ad_dhcp_entry_full 5017:ad_dhcp_ip_dup 5018:ad_dhcp_mac_dup 10000:eqptVol_err 10001:eqptEqpttemp_err 10002:eqptFan_err 10003:eqptHw_rtc_fail 10004:eqptHw_mon_fail 10005:eqptCold_start 10006:eqptWarm_start 10007:eqptAlm_input 10008:eqptI2c_err 10009:eqptAlm_input2 10010:eqptAlm_input3 15000:sysReboot 15001:sysAco 15002:sysAlm_clear 15003:sysLogin_fail 15004:sysAnti_spoofing 15005:sysAlm_svrty_change 20000:enetUp 20001:enetDown " ::= { alarmConfEntry 1 } alarmConfFacility OBJECT-TYPE SYNTAX INTEGER { local1(1), local2(2), local3(3), local4(4), local5(5), local6(6), local7(7) } MAX-ACCESS read-write STATUS current DESCRIPTION "Alarm facility." ::= { alarmConfEntry 2 } alarmConfTarget OBJECT-TYPE SYNTAX INTEGER MAX-ACCESS read-write STATUS current DESCRIPTION "The destination which alarms are reported to. Set the bit to 1 to enable the target. BIT 1: snmp trap BIT 2: syslog" ::= { alarmConfEntry 3 } alarmConfSeverity OBJECT-TYPE SYNTAX INTEGER { critical(1), major(2), minor(3), info(4) } MAX-ACCESS read-write STATUS current DESCRIPTION "Alarm severity" ::= { alarmConfEntry 4 } alarmConfClearable OBJECT-TYPE SYNTAX INTEGER { clearable(1), unclearable(2) } MAX-ACCESS read-write STATUS current DESCRIPTION "Setting the object to one indicates that the alarm is to be cleared when user submits alarm clear." ::= { alarmConfEntry 5 } -- Alarm Current Table alarmCurrTable OBJECT-TYPE SYNTAX SEQUENCE OF AlarmCurrEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "This table includes current alarm information." ::= { alarmconf 3 } alarmCurrEntry OBJECT-TYPE SYNTAX AlarmCurrEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "An entry in alarmCurrTable." INDEX { alarmCurrIndex } ::= { alarmCurrTable 1 } AlarmCurrEntry ::= SEQUENCE { alarmCurrIndex INTEGER, alarmCurrOccurTime TimeTicks, alarmCurrTrapOid OBJECT IDENTIFIER, alarmCurrParam1 INTEGER, alarmCurrParam2 INTEGER, alarmCurrParam3 INTEGER, alarmCurrParam4 INTEGER, alarmCurrParam5 INTEGER, alarmCurrParam6 INTEGER, alarmCurrParam7 INTEGER, alarmCurrParam8 INTEGER, alarmCurrTimeDescr DisplayString, alarmCurrSeverity INTEGER, alarmCurrDescr DisplayString } alarmCurrIndex OBJECT-TYPE SYNTAX INTEGER MAX-ACCESS read-only STATUS current DESCRIPTION "Index of the alarm." ::= { alarmCurrEntry 1 } alarmCurrOccurTime OBJECT-TYPE SYNTAX TimeTicks MAX-ACCESS read-only STATUS current DESCRIPTION "Alarm occurence time (in hundredths of a second) since the system was last re-initialized." ::= { alarmCurrEntry 2 } alarmCurrTrapOid OBJECT-TYPE SYNTAX OBJECT IDENTIFIER MAX-ACCESS read-only STATUS current DESCRIPTION "Trap OID of the alarm." ::= { alarmCurrEntry 3 } alarmCurrParam1 OBJECT-TYPE SYNTAX INTEGER MAX-ACCESS read-only STATUS current DESCRIPTION "The 1st parameter of the alarm." ::= { alarmCurrEntry 4 } alarmCurrParam2 OBJECT-TYPE SYNTAX INTEGER MAX-ACCESS read-only STATUS current DESCRIPTION "The 2nd parameter of the alarm." ::= { alarmCurrEntry 5 } alarmCurrParam3 OBJECT-TYPE SYNTAX INTEGER MAX-ACCESS read-only STATUS current DESCRIPTION "The 3rd parameter of the alarm." ::= { alarmCurrEntry 6 } alarmCurrParam4 OBJECT-TYPE SYNTAX INTEGER MAX-ACCESS read-only STATUS current DESCRIPTION "The 4th parameter of the alarm." ::= { alarmCurrEntry 7 } alarmCurrParam5 OBJECT-TYPE SYNTAX INTEGER MAX-ACCESS read-only STATUS current DESCRIPTION "The 5th parameter of the alarm." ::= { alarmCurrEntry 8 } alarmCurrParam6 OBJECT-TYPE SYNTAX INTEGER MAX-ACCESS read-only STATUS current DESCRIPTION "The 6th parameter of the alarm." ::= { alarmCurrEntry 9 } alarmCurrParam7 OBJECT-TYPE SYNTAX INTEGER MAX-ACCESS read-only STATUS current DESCRIPTION "The 7th parameter of the alarm." ::= { alarmCurrEntry 10 } alarmCurrParam8 OBJECT-TYPE SYNTAX INTEGER MAX-ACCESS read-only STATUS current DESCRIPTION "The 8th parameter of the alarm." ::= { alarmCurrEntry 11 } alarmCurrTimeDescr OBJECT-TYPE SYNTAX DisplayString MAX-ACCESS read-only STATUS current DESCRIPTION "The string representation of occurence time (YYYY/MM/DD HH:MM:SS)." ::= { alarmCurrEntry 12 } alarmCurrSeverity OBJECT-TYPE SYNTAX INTEGER { critical(1), major(2), minor(3), info(4) } MAX-ACCESS read-only STATUS current DESCRIPTION "The severity of the alarm." ::= { alarmCurrEntry 13 } alarmCurrDescr OBJECT-TYPE SYNTAX DisplayString MAX-ACCESS read-only STATUS current DESCRIPTION "The description of the alarm." ::= { alarmCurrEntry 14 } -- Alarm Severity Port Table alarmSeverityPortTable OBJECT-TYPE SYNTAX SEQUENCE OF AlarmSeverityPortEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "This table includes the configuration of alarm reporting severity threshold for each port." ::= { alarmconf 4 } alarmSeverityPortEntry OBJECT-TYPE SYNTAX AlarmSeverityPortEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "An entry in alarmSeverityPortTable." INDEX { ifIndex } ::= { alarmSeverityPortTable 1 } AlarmSeverityPortEntry ::= SEQUENCE { severityThresh INTEGER } severityThresh OBJECT-TYPE SYNTAX INTEGER { critical(1), major(2), minor(3), info(4) } MAX-ACCESS read-write STATUS current DESCRIPTION "The minimum alarm severity that is reported." ::= { alarmSeverityPortEntry 1 } ---------------------------------------- -- diagnostic ---------------------------------------- selt OBJECT IDENTIFIER ::= { diagnostic 3 } -------------------- -- selt -------------------- seltTarget OBJECT-TYPE SYNTAX INTEGER MAX-ACCESS read-write STATUS current DESCRIPTION "IfIndex of the port which would be performed single end loopback test." ::= { selt 1 } seltOps OBJECT-TYPE SYNTAX INTEGER MAX-ACCESS read-write STATUS current DESCRIPTION "The manager sets the object to 1 to start the selt and the agent clears the object to zero when selt is successfully completed." ::= { selt 2 } seltStatus OBJECT-TYPE SYNTAX DisplayString MAX-ACCESS read-only STATUS current DESCRIPTION "Status description of the selt result." ::= { selt 3 } seltCableType OBJECT-TYPE SYNTAX INTEGER { awg24(1), awg26(2) } MAX-ACCESS read-only STATUS current DESCRIPTION "The cable type that selt result indicates." ::= { selt 4 } seltLoopEstimateLengthFt OBJECT-TYPE SYNTAX INTEGER UNITS "feet" MAX-ACCESS read-only STATUS current DESCRIPTION "The estimated loop length that selt result indicates." ::= { selt 5 } seltLoopEstimateLengthMeter OBJECT-TYPE SYNTAX INTEGER UNITS "meter" MAX-ACCESS read-only STATUS current DESCRIPTION "The estimated loop length that selt result indicates." ::= { selt 6 } ---------------------------------------- -- multicast ---------------------------------------- -- Obsoleted in calix MRD20 since Revision 1.20 at 2009/06/25 by niceguy -- Object mcastBandwidth, igmpCount below is kept for e5-110 R1.x below. Not used for R2.x and above. mcastBandwidth OBJECT IDENTIFIER ::= { multicast 4 } igmpCount OBJECT IDENTIFIER ::= { multicast 5 } mvlan OBJECT IDENTIFIER ::= { multicast 6 } queryVid OBJECT IDENTIFIER ::= { multicast 7 } igmpTimer OBJECT IDENTIFIER ::= { multicast 11 } auditQuery OBJECT IDENTIFIER ::= { multicast 12 } igmpProfile OBJECT IDENTIFIER ::= { multicast 13 } igmpEnable OBJECT-TYPE SYNTAX INTEGER { enableProxy(1), enableSnooping(2), disable(3) } MAX-ACCESS read-write STATUS current DESCRIPTION "Enable/disable IGMP protocol." ::= { multicast 1 } igmpVersion OBJECT-TYPE SYNTAX INTEGER { v2(1), v3(2) } MAX-ACCESS read-write STATUS current DESCRIPTION "Setting IGMP version." ::= { multicast 9 } igmpLeaveMode OBJECT-TYPE SYNTAX INTEGER { immediateLeave(1), lastMemberQuery(2) } MAX-ACCESS read-write STATUS current DESCRIPTION "Configure IGMP leave message handling mode." ::= { multicast 10 } -------------------- -- bandwidth -------------------- mcastDefaultBandwidth OBJECT-TYPE SYNTAX INTEGER (1..100000) UNITS "Kbps" MAX-ACCESS read-write STATUS current DESCRIPTION "Default bandwidth requirement for a multicast channel." ::= { mcastBandwidth 1 } maxNumOfMcastBw OBJECT-TYPE SYNTAX INTEGER MAX-ACCESS read-only STATUS current DESCRIPTION "The maximum number of row entries that user can create in mcastBwTable." ::= { mcastBandwidth 2 } -- mcastBwTable mcastBwTable OBJECT-TYPE SYNTAX SEQUENCE OF McastBwEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "This table defines bandwidth budget for a range of multicast IP channels." ::= { mcastBandwidth 3 } mcastBwEntry OBJECT-TYPE SYNTAX McastBwEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "An entry of mcastBwTable." INDEX { mcastBwIndex, mcastBwStartIp, mcastBwEndIp } ::= { mcastBwTable 1 } McastBwEntry ::= SEQUENCE { mcastBwIndex INTEGER, mcastBwStartIp IpAddress, mcastBwEndIp IpAddress, mcastBwBandwidth INTEGER, mcastBwRowStatus RowStatus } mcastBwIndex OBJECT-TYPE SYNTAX INTEGER MAX-ACCESS read-only STATUS current DESCRIPTION "The index which specify the entry." ::= { mcastBwEntry 1 } mcastBwStartIp OBJECT-TYPE SYNTAX IpAddress MAX-ACCESS read-only STATUS current DESCRIPTION "The start multicast IP of the bandwidth control range." ::= { mcastBwEntry 2 } mcastBwEndIp OBJECT-TYPE SYNTAX IpAddress MAX-ACCESS read-only STATUS current DESCRIPTION "The end multicast IP of the bandwidth control range." ::= { mcastBwEntry 3 } mcastBwBandwidth OBJECT-TYPE SYNTAX INTEGER UNITS "Kbps" MAX-ACCESS read-create STATUS current DESCRIPTION "The bandwidth budget for the multicast IP channels." ::= { mcastBwEntry 4 } mcastBwRowStatus OBJECT-TYPE SYNTAX RowStatus MAX-ACCESS read-create STATUS current DESCRIPTION "The row status of the entry." ::= { mcastBwEntry 5 } -- mcastBwPortTable mcastBwPortTable OBJECT-TYPE SYNTAX SEQUENCE OF McastBwPortEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "This table specify the multicast bandwidth control of the port." ::= { mcastBandwidth 4 } mcastBwPortEntry OBJECT-TYPE SYNTAX McastBwPortEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "An entry of mcastBwPortTable." INDEX { ifIndex } ::= { mcastBwPortTable 1 } McastBwPortEntry ::= SEQUENCE { mcastBwPortEnable INTEGER, mcastBwPortBandwidth INTEGER } mcastBwPortEnable OBJECT-TYPE SYNTAX INTEGER { enable(1), disable(2) } MAX-ACCESS read-write STATUS current DESCRIPTION "Enable/disable multicast bandwidth control for a port." ::= { mcastBwPortEntry 1 } mcastBwPortBandwidth OBJECT-TYPE SYNTAX INTEGER UNITS "Kbps" MAX-ACCESS read-write STATUS current DESCRIPTION "Set bandwidth threshold for a port." ::= { mcastBwPortEntry 2 } -------------------- -- igmpCount -------------------- igmpCountPortTable OBJECT-TYPE SYNTAX SEQUENCE OF IgmpCountPortEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "This table specify the IGMP count limiting of the port." ::= { igmpCount 1 } igmpCountPortEntry OBJECT-TYPE SYNTAX IgmpCountPortEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "An entry of igmpCountPortTable." INDEX { ifIndex } ::= { igmpCountPortTable 1 } IgmpCountPortEntry ::= SEQUENCE { igmpCountPortEnable INTEGER, igmpCountPortLimit INTEGER } igmpCountPortEnable OBJECT-TYPE SYNTAX INTEGER { enable(1), disable(2) } MAX-ACCESS read-write STATUS current DESCRIPTION "Enable/disable IGMP count limiting for a port." ::= { igmpCountPortEntry 1 } igmpCountPortLimit OBJECT-TYPE SYNTAX INTEGER (0..16) MAX-ACCESS read-write STATUS current DESCRIPTION "The maximum allowed IGMP report count for a port." ::= { igmpCountPortEntry 2 } -------------------- -- mvlan -------------------- maxNumOfMvlan OBJECT-TYPE SYNTAX INTEGER MAX-ACCESS read-only STATUS current DESCRIPTION "The maximum number of row entries that user can create in mvlanTable." ::= { mvlan 1 } -- mvlanTable mvlanTable OBJECT-TYPE SYNTAX SEQUENCE OF MvlanEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "A table containing static configuration information for each multicast VLAN configured into the device." ::= { mvlan 2 } mvlanEntry OBJECT-TYPE SYNTAX MvlanEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "An entry of mvlanTable." INDEX { mvlanIndex } ::= { mvlanTable 1 } MvlanEntry ::= SEQUENCE { mvlanIndex VlanIndex, mvlanName DisplayString, mvlanEgressPorts PortList, mvlanUntaggedPorts PortList, mvlanRowStatus RowStatus } mvlanIndex OBJECT-TYPE SYNTAX VlanIndex MAX-ACCESS read-only STATUS current DESCRIPTION "The VLAN-ID refering to this VLAN." ::= { mvlanEntry 1 } mvlanName OBJECT-TYPE SYNTAX DisplayString (SIZE (0..31)) MAX-ACCESS read-create STATUS current DESCRIPTION "An administratively assigned string, which may be used to identify the VLAN." ::= { mvlanEntry 2 } mvlanEgressPorts OBJECT-TYPE SYNTAX PortList MAX-ACCESS read-create STATUS current DESCRIPTION "The set of ports which are permanently assigned to the egress list for this multicast VLAN." ::= { mvlanEntry 3 } mvlanUntaggedPorts OBJECT-TYPE SYNTAX PortList MAX-ACCESS read-create STATUS current DESCRIPTION "The set of ports which should transmit egress packets for this multicast VLAN as untagged." ::= { mvlanEntry 4 } mvlanRowStatus OBJECT-TYPE SYNTAX RowStatus MAX-ACCESS read-create STATUS current DESCRIPTION "This object indicates the status of this entry." ::= { mvlanEntry 5 } -- mvlanTranslateTable mvlanTranslateTable OBJECT-TYPE SYNTAX SEQUENCE OF MvlanTranslateEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "A table that contains multicast to VLAN translation." ::= { mvlan 3 } mvlanTranslateEntry OBJECT-TYPE SYNTAX MvlanTranslateEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "An entry of mvlanTranslateTable." INDEX { dot1qVlanIndex, mvlanTranslateIndex } ::= { mvlanTranslateTable 1 } MvlanTranslateEntry ::= SEQUENCE { mvlanTranslateIndex INTEGER, mvlanTranslateStartIp IpAddress, mvlanTranslateEndIp IpAddress } mvlanTranslateIndex OBJECT-TYPE SYNTAX INTEGER MAX-ACCESS read-only STATUS current DESCRIPTION "The index which specif the entry." ::= { mvlanTranslateEntry 1 } mvlanTranslateStartIp OBJECT-TYPE SYNTAX IpAddress MAX-ACCESS read-write STATUS current DESCRIPTION "The start IP of the multicast VLAN translation." ::= { mvlanTranslateEntry 2 } mvlanTranslateEndIp OBJECT-TYPE SYNTAX IpAddress MAX-ACCESS read-write STATUS current DESCRIPTION "The end IP of the multicast VLAN translation." ::= { mvlanTranslateEntry 3 } -------------------- -- queryVid -------------------- maxNumOfQryVid OBJECT-TYPE SYNTAX INTEGER MAX-ACCESS read-only STATUS current DESCRIPTION "The maximum number of row entries that user can create in qryVidConfTable." ::= { queryVid 1 } -- qryVidConfTable qryVidConfTable OBJECT-TYPE SYNTAX SEQUENCE OF QryVidConfEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "This table defines statically set VLANs used for response IGMP report." ::= { queryVid 2 } qryVidConfEntry OBJECT-TYPE SYNTAX QryVidConfEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "An entry in qryVidConfTable." INDEX { qryVid } ::= { qryVidConfTable 1 } QryVidConfEntry ::= SEQUENCE { qryVid INTEGER, qryVidRowStatus RowStatus } qryVid OBJECT-TYPE SYNTAX INTEGER MAX-ACCESS read-only STATUS current DESCRIPTION "VLAN ID." ::= { qryVidConfEntry 1 } qryVidRowStatus OBJECT-TYPE SYNTAX RowStatus MAX-ACCESS read-create STATUS current DESCRIPTION "This object indicates the status of this entry." ::= { qryVidConfEntry 2 } -- qryVidStatusTable qryVidStatusTable OBJECT-TYPE SYNTAX SEQUENCE OF QryVidStatusEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "This table shows statically set or dynamically learned VLANs used for response IGMP report." ::= { queryVid 3 } qryVidStatusEntry OBJECT-TYPE SYNTAX QryVidStatusEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "An entry in qryVidStatusTable." INDEX { qryVid } ::= { qryVidStatusTable 1 } QryVidStatusEntry ::= SEQUENCE { qryVidType INTEGER } qryVidType OBJECT-TYPE SYNTAX INTEGER { static(1), dynamic(2) } MAX-ACCESS read-only STATUS current DESCRIPTION "VLAN type." ::= { qryVidStatusEntry 1 } -------------------- -- igmpTimer -------------------- igmpQryInterval OBJECT-TYPE SYNTAX INTEGER (10..1000) MAX-ACCESS read-write STATUS current DESCRIPTION "Set IGMP query interval, 10~1000 in seconds." ::= { igmpTimer 1 } igmpRobust OBJECT-TYPE SYNTAX INTEGER (1..5) MAX-ACCESS read-write STATUS current DESCRIPTION "Set IGMP query Robustness, 1~5." ::= { igmpTimer 2 } igmpQryRespInterval OBJECT-TYPE SYNTAX INTEGER (1..100) MAX-ACCESS read-write STATUS current DESCRIPTION "Set IGMP query response interval, 1~100 in 100 milliseconds." ::= { igmpTimer 3 } igmpLastMemQryInterval OBJECT-TYPE SYNTAX INTEGER (1..5) MAX-ACCESS read-write STATUS current DESCRIPTION "Set IGMP Last Member Query interval, 1~5 in 100 milliseconds." ::= { igmpTimer 4 } igmpLastMemQryRobust OBJECT-TYPE SYNTAX INTEGER (1..5) MAX-ACCESS read-write STATUS current DESCRIPTION "Set Last Member Query Robustness, 1~5." ::= { igmpTimer 5 } -------------------- -- auditQuery -------------------- auditQryEnable OBJECT-TYPE SYNTAX INTEGER { enable(1), disable(2) } MAX-ACCESS read-write STATUS current DESCRIPTION "Enable/disable IGMP audit query." ::= { auditQuery 1 } auditQryInterval OBJECT-TYPE SYNTAX INTEGER (1..4) MAX-ACCESS read-write STATUS current DESCRIPTION "Set IGMP Audit Query Interval, 1~4 in 100 milliseconds." ::= { auditQuery 2 } auditQryRobust OBJECT-TYPE SYNTAX INTEGER (1..5) MAX-ACCESS read-write STATUS current DESCRIPTION "Set IGMP Audit Query Robustness, 1~5." ::= { auditQuery 3 } -------------------- -- igmpProfile -------------------- maxNumberOfIgmpProfiles OBJECT-TYPE SYNTAX INTEGER MAX-ACCESS read-only STATUS current DESCRIPTION "The max number of IGMP profiles in the system." ::= { igmpProfile 1 } igmpProfileTable OBJECT-TYPE SYNTAX SEQUENCE OF IgmpProfileEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "A table that contains IGMP Profiles." ::= { igmpProfile 2 } igmpProfileEntry OBJECT-TYPE SYNTAX IgmpProfileEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "The entry of IGMP Profile table." INDEX {IMPLIED igmpProfileName } ::= { igmpProfileTable 1 } IgmpProfileEntry ::= SEQUENCE { igmpProfileName DisplayString, igmpProfileEnable INTEGER, igmpProfileMaxGroup INTEGER, igmpProfileRowStatus RowStatus } igmpProfileName OBJECT-TYPE SYNTAX DisplayString (SIZE (1..31)) MAX-ACCESS read-only STATUS current DESCRIPTION "The IGMP Profile name." ::= { igmpProfileEntry 1 } igmpProfileEnable OBJECT-TYPE SYNTAX INTEGER { enable(1), disable(2) } MAX-ACCESS read-write STATUS current DESCRIPTION "Enable/disable IGMP Profile." ::= { igmpProfileEntry 2 } igmpProfileMaxGroup OBJECT-TYPE SYNTAX INTEGER (1..16) MAX-ACCESS read-write STATUS current DESCRIPTION "Set maximum allowed multicast group, 1~16." ::= { igmpProfileEntry 3 } igmpProfileRowStatus OBJECT-TYPE SYNTAX RowStatus MAX-ACCESS read-create STATUS current DESCRIPTION "The row status of the IGMP Profile entry." ::= { igmpProfileEntry 4 } igmpFilterTable OBJECT-TYPE SYNTAX SEQUENCE OF IgmpFilterEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "A table that contains IGMP Filters." ::= { igmpProfile 3 } igmpFilterEntry OBJECT-TYPE SYNTAX IgmpFilterEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "The entry of IGMP Filter table." INDEX { igmpProfileName, igmpFilterIndex } ::= { igmpFilterTable 1 } IgmpFilterEntry ::= SEQUENCE { igmpFilterIndex INTEGER, igmpFilterStartIp IpAddress, igmpFilterEndIp IpAddress } igmpFilterIndex OBJECT-TYPE SYNTAX INTEGER MAX-ACCESS read-only STATUS current DESCRIPTION "The index which specifies the filter rule." ::= { igmpFilterEntry 1 } igmpFilterStartIp OBJECT-TYPE SYNTAX IpAddress MAX-ACCESS read-create STATUS current DESCRIPTION "The start IP of the filter rule." ::= { igmpFilterEntry 2 } igmpFilterEndIp OBJECT-TYPE SYNTAX IpAddress MAX-ACCESS read-create STATUS current DESCRIPTION "The end IP of the filter rule." ::= { igmpFilterEntry 3 } igmpProfilePortTable OBJECT-TYPE SYNTAX SEQUENCE OF IgmpProfilePortEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "This table specifies the IGMP Profile of the port." ::= { igmpProfile 4 } igmpProfilePortEntry OBJECT-TYPE SYNTAX IgmpProfilePortEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "An entry in igmpProfilePortTable." INDEX { ifIndex } ::= { igmpProfilePortTable 1 } IgmpProfilePortEntry ::= SEQUENCE { igmpProfilePortProfile OCTET STRING } igmpProfilePortProfile OBJECT-TYPE SYNTAX OCTET STRING (SIZE (1..31)) MAX-ACCESS read-write STATUS current DESCRIPTION "The IGMP Profile of the port." ::= { igmpProfilePortEntry 1 } ---------------------------------------- -- port ---------------------------------------- -- Since we define it latter, mark the definition here -- subrPortTable OBJECT IDENTIFIER ::= { port 1 } adslPort OBJECT IDENTIFIER ::= { port 2 } pvc OBJECT IDENTIFIER ::= { port 4 } ppvc OBJECT IDENTIFIER ::= { port 5 } rpvc OBJECT IDENTIFIER ::= { port 8 } -- Since we define it latter, mark the definition here -- dsBcastDisableTable OBJECT IDENTIFIER ::= { port 9 } paepvc OBJECT IDENTIFIER ::= { port 10 } tlspvc OBJECT IDENTIFIER ::= { port 11 } ipbpvc OBJECT IDENTIFIER ::= { port 12 } -- obsoleted since R3.0 at 2009/11/26 dtpvc OBJECT IDENTIFIER ::= { port 14 } snrMgn OBJECT IDENTIFIER ::= { port 15 } dslRate OBJECT IDENTIFIER ::= { port 16 } -- G.bond start from 51 gbond OBJECT IDENTIFIER ::= { port 51 } -- Subscriber Port Table subrPortTable OBJECT-TYPE SYNTAX SEQUENCE OF SubrPortEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "This table includes subscriber attributes for the port." ::= { port 1 } subrPortEntry OBJECT-TYPE SYNTAX SubrPortEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "An entry in subrPortTable." INDEX { ifIndex } ::= { subrPortTable 1 } SubrPortEntry ::= SEQUENCE { subrPortName DisplayString, subrPortTel DisplayString } subrPortName OBJECT-TYPE SYNTAX DisplayString (SIZE (0..31)) MAX-ACCESS read-write STATUS current DESCRIPTION "Name of the subscriber." ::= { subrPortEntry 1 } subrPortTel OBJECT-TYPE SYNTAX DisplayString (SIZE (0..15)) MAX-ACCESS read-write STATUS current DESCRIPTION "Telephone number of the subscriber." ::= { subrPortEntry 2 } -------------------- -- adslPort -------------------- -- ADSL Line Table adslLineConfTable OBJECT-TYPE SYNTAX SEQUENCE OF AdslLineConfEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "This table includes common attributes describing the ADSL line." ::= { adslPort 1 } adslLineConfEntry OBJECT-TYPE SYNTAX AdslLineConfEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "An entry in adslLineConfTable." INDEX { ifIndex } ::= { adslLineConfTable 1 } AdslLineConfEntry ::= SEQUENCE { adslLineConfAdslMode INTEGER, adslLineConfAnnexL INTEGER, adslLineConfAnnexM INTEGER, adslLineConfAnnexI INTEGER, adslLineConfOptionMask INTEGER, adslLineConfPowerMgmt INTEGER, adslLineConfPowerMode INTEGER, adslLineConfAturMaxTxPower INTEGER, adslLineConfAtucMaxTxPower INTEGER, adslLineConfMaxRxPower INTEGER, adslLineConfAturCarrierMask OCTET STRING, adslLineConfAtucCarrierMask0 OCTET STRING, adslLineConfAtucCarrierMask1 OCTET STRING, adslLineConfAturInp INTEGER, adslLineConfAtucInp INTEGER, adslLineConfL0Time INTEGER, adslLineConfL2Time INTEGER, adslLineConfL2ATPR INTEGER, adslLineConfL2ATPRT INTEGER, adslLineConfMaxL2Rate INTEGER, adslLineConfMinL2Rate INTEGER, adslLineConfL0toL2Rate INTEGER, adslLineConfNitro INTEGER, adslLineConfUSPhyr INTEGER, adslLineConfDSPhyr INTEGER } adslLineConfAdslMode OBJECT-TYPE SYNTAX INTEGER { gDotLite(1), gDotDmt(2), t1Dot413(3), auto(4), etsi(5), adsl2(6), adsl2Plus(7) } MAX-ACCESS read-write STATUS current DESCRIPTION "G.lite and T1.413 are only applicable to annex A board. ETSI is only applicable to annex B board." ::= { adslLineConfEntry 1 } adslLineConfAnnexL OBJECT-TYPE SYNTAX INTEGER { enableNarrowMode(1), enableWideMode(2), disable(3) } MAX-ACCESS read-write STATUS current DESCRIPTION "Enable/disable annex L for the port(Only in AnnexA)." ::= { adslLineConfEntry 2 } adslLineConfAnnexM OBJECT-TYPE SYNTAX INTEGER { enable(1), disable(2) } MAX-ACCESS read-write STATUS current DESCRIPTION "Enable/disable annex M for the port(For BCM AnnexA solution)." ::= { adslLineConfEntry 3 } adslLineConfAnnexI OBJECT-TYPE SYNTAX INTEGER { enable(1), disable(2) } MAX-ACCESS read-write STATUS current DESCRIPTION "Enable/disable annex I for the port(For BCM AnnexA solution)." ::= { adslLineConfEntry 4 } adslLineConfOptionMask OBJECT-TYPE SYNTAX INTEGER MAX-ACCESS read-write STATUS current DESCRIPTION "The semantic for each bit is: BIT 1 : Disable Trellis BIT 2 : Disable Reed-Solomon BIT 3 : Disable upstream bitswap BIT 4 : Disable downstream bitswap BIT 5 : Disable 1-bit constellation BIT 6 : Disable transmit windowing BIT 7 : Disable s=0.5 support (ADSL1 only) BIT 8 : Disable G.lite rate limit (ADSL1 only) BIT 9 : Enable Nitro BIT 10: Enable US PHYR BIT 11: ENABLE DS PHYR" ::= { adslLineConfEntry 5 } adslLineConfPowerMgmt OBJECT-TYPE SYNTAX INTEGER { enableL2(1), enableL2(2), disable(3) } MAX-ACCESS read-write STATUS current DESCRIPTION "Enable/disable power management for the port." ::= { adslLineConfEntry 6 } adslLineConfPowerMode OBJECT-TYPE SYNTAX INTEGER { fix(1), priorityToPower(2), priorityToRate(3) } MAX-ACCESS read-write STATUS current DESCRIPTION "The power mode of the ADSL line." ::= { adslLineConfEntry 7 } adslLineConfAturMaxTxPower OBJECT-TYPE SYNTAX INTEGER (-130..200) UNITS "tenth dBm" MAX-ACCESS read-write STATUS current DESCRIPTION "The maximum allowed transmit power of ATU-R." ::= { adslLineConfEntry 8 } adslLineConfAtucMaxTxPower OBJECT-TYPE SYNTAX INTEGER (-50..200) UNITS "tenth dBm" MAX-ACCESS read-write STATUS current DESCRIPTION "The maximum allowed transmit power of ATU-C." ::= { adslLineConfEntry 9 } adslLineConfMaxRxPower OBJECT-TYPE SYNTAX INTEGER (-255..255) UNITS "tenth dBm" MAX-ACCESS read-write STATUS current DESCRIPTION "The maximum aggregate received power." ::= { adslLineConfEntry 10 } adslLineConfAturCarrierMask OBJECT-TYPE SYNTAX OCTET STRING MAX-ACCESS read-write STATUS current DESCRIPTION "The upstream carrier mask. For CTLM AnnexA solution, bin is from 0 to 31; CTLM AnnexB solution, bin is from 0 to 63; BCM solution, bin is from 0 to 63. Bit set to 1 indicates the bin is masked off." ::= { adslLineConfEntry 11 } adslLineConfAtucCarrierMask0 OBJECT-TYPE SYNTAX OCTET STRING MAX-ACCESS read-write STATUS current DESCRIPTION "The downstream carrier mask. For CTLM AnnexA solution, bin is from 32 to 255; CTLM AnnexB solution, bin is from 64 to 255; BCM solution, bin is from 32 to 255. Bit set to 1 indicates the bin is masked off." ::= { adslLineConfEntry 12 } adslLineConfAtucCarrierMask1 OBJECT-TYPE SYNTAX OCTET STRING MAX-ACCESS read-write STATUS current DESCRIPTION "The downstream carrier mask from bin 256 to 511. Bit set to 1 indicates the bin is masked off." ::= { adslLineConfEntry 13 } adslLineConfAturInp OBJECT-TYPE SYNTAX INTEGER { zero(1), zeroPointFive(2), one(3), two(4), four(5), eight(6), sixteen(7) } MAX-ACCESS read-write STATUS current DESCRIPTION "The upstream Impulse Noise Protection minimum setting in unit of DMT symbol. For CTLM solution, user can set value from 1 ~ 4, but for BCM solution, user can set value from 1 ~ 7." ::= { adslLineConfEntry 14 } adslLineConfAtucInp OBJECT-TYPE SYNTAX INTEGER { zero(1), zeroPointFive(2), one(3), two(4), four(5), eight(6), sixteen(7) } MAX-ACCESS read-write STATUS current DESCRIPTION "The downstream Impulse Noise Protection minimum setting in unit of DMT symbol. For CTLM solution, user can set value from 1 ~ 4, but for BCM solution, user can set value from 1 ~ 7." ::= { adslLineConfEntry 15 } adslLineConfL0Time OBJECT-TYPE SYNTAX INTEGER MAX-ACCESS read-write STATUS current DESCRIPTION "Set the minimum time in seconds that the ADSL line must stay in L0 power mode before changing to the L2 power mode. For CTLM solution, the range is 120 ~ 65535; for BCM solution, the range is 10 ~ 65535." ::= { adslLineConfEntry 16 } adslLineConfL2Time OBJECT-TYPE SYNTAX INTEGER MAX-ACCESS read-write STATUS current DESCRIPTION "Set minimum time in seconds that the ADSL line must stay in the L2 power mode before reducing the power again in the L2 power mode. For CTLM solution, the range is 60 ~ 65535; for BCM solution, the range is 10 ~ 65535." ::= { adslLineConfEntry 17 } adslLineConfL2ATPR OBJECT-TYPE SYNTAX INTEGER UNITS "dB" MAX-ACCESS read-write STATUS current DESCRIPTION "Set the maximum Aggregate Transmit Power Reduction (ATPR) in decibels (dB) that is permitted in a L2 power reduction. The system can gradually decrease the ADSL line transmission power while it is in the L2 power mode. This is the largest individual power reduction allowed in the L2 power mode. For CTLM solution, the range is 1 ~ 5(dB); for BCM solution, the range is 0 ~ 15(dB)." ::= { adslLineConfEntry 18 } adslLineConfL2ATPRT OBJECT-TYPE SYNTAX INTEGER UNITS "dB" MAX-ACCESS read-write STATUS current DESCRIPTION "the maximum Aggregate Transmit Power Reduction Total (ATPRT) in decibels (dB) that is permitted in the L2 power mode. This is the total transmit power decrease that is allowed to occur in the L2 power mode. For CTLM solution, the range is 1 ~ 40(dB); for BCM solution, the range is 0 ~ 15(dB)." ::= { adslLineConfEntry 19 } adslLineConfMaxL2Rate OBJECT-TYPE SYNTAX INTEGER UNITS "kbps" MAX-ACCESS read-write STATUS current DESCRIPTION "configured maximum L2 rate. (32~4096 Kbps, 4 Kbps resolution. For CTLM solution, 0 for system assign; for BCM solution, default:4096.)" ::= { adslLineConfEntry 20 } adslLineConfMinL2Rate OBJECT-TYPE SYNTAX INTEGER UNITS "kbps" MAX-ACCESS read-write STATUS current DESCRIPTION "configured minimum L2 rate. (32~4096 Kbps, 4 Kbps resolution, For CTLM solution, 0 for system assign; for BCM solution, default:32.)" ::= { adslLineConfEntry 21 } adslLineConfL0toL2Rate OBJECT-TYPE SYNTAX INTEGER UNITS "kbps" MAX-ACCESS read-write STATUS current DESCRIPTION "configured transition L0 to L2 rate. (<=min_l2rate/2 and >= 16 Kbps, For CTLM solution, 0 for system assign; for BCM solution, default:16.)" ::= { adslLineConfEntry 22 } adslLineConfNitro OBJECT-TYPE SYNTAX INTEGER { enable(1), disable(2) } MAX-ACCESS read-write STATUS current DESCRIPTION "Enable/disable nitro mode for the port(For BCM solution)." ::= { adslLineConfEntry 23 } adslLineConfUSPhyr OBJECT-TYPE SYNTAX INTEGER { enable(1), disable(2) } MAX-ACCESS read-write STATUS current DESCRIPTION "Enable/disable Upstream PHYR for the port(For BCM solution)." ::= { adslLineConfEntry 24 } adslLineConfDSPhyr OBJECT-TYPE SYNTAX INTEGER { enable(1), disable(2) } MAX-ACCESS read-write STATUS current DESCRIPTION "Enable/disable Downstream PHYR for the port(For BCM solution)." ::= { adslLineConfEntry 25 } -- ADSL Port Batch Set adslPortBatchSet OBJECT IDENTIFIER ::= { adslPort 3 } adslPortTarget OBJECT-TYPE SYNTAX OCTET STRING MAX-ACCESS read-write STATUS current DESCRIPTION "The managed object is used for identify the target on which the port configuration should be performed. The target is encoded as: Byte 1: 0, Reserved(chaises) Byte 2~3: 0,0 Reserved(slot) Byte 4: 0, reserved Byte 5~11:each octet specifies a set of eight ports, with the first octet specifying ports 1 through 8, etc." ::= { adslPortBatchSet 1 } adslPortOps OBJECT-TYPE SYNTAX INTEGER MAX-ACCESS read-write STATUS current DESCRIPTION "The managed object is for ADSL line configuration. When the EMS wants to issue the desired operation, the EMS shall send SNMP-SET message to set the corresponding bit value to be 1. The various bit positions are: BIT 1: enable port BIT 2: disable port BIT 3: set ADSL mode BIT 4: set line profile BIT 5: set alarm profile BIT 6: enable Annex L to be narrow mode(Only in AnnexA) BIT 7: enable Annex L to be wide mode(Only in AnnexA) BIT 8: disable Annex L(Only in AnnexA) BIT 9: enable Annex M (For BCM AnnexA solution) BIT 10: disable Annex M (For BCM AnnexA solution) BIT 11: enable Annex I (For BCM AnnexA solution) BIT 12: disable Annex I (For BCM AnnexA solution) BIT 13: set option mask BIT 14: enable power management mode to be L2 BIT 15: enable power management mode to be L2 BIT 16: disable power management mode BIT 17: set power mode to be fixed BIT 18: set power mode to be priority to power BIT 19: set power mode to be priority to rate BIT 20: set ATU-R max Tx power BIT 21: set ATU-C max Tx power BIT 22: set max Rx power BIT 23: set ATU-R carrier mask BIT 24: set ATU-C carrier mask BIT 25: set ATU-R INP minimum setting BIT 26: set ATU-C INP minimum setting" ::= { adslPortBatchSet 2 } adslPortOps2 OBJECT-TYPE SYNTAX INTEGER MAX-ACCESS read-write STATUS current DESCRIPTION "The managed object is for ADSL line configuration. When the EMS wants to issue the desired operation, the EMS shall send SNMP-SET message to set the corresponding bit value to be 1. The various bit positions are: BIT 1: set L0 Time BIT 2: set L2 Time BIT 3: set L2 ATPR BIT 4: set L2 ATPRT BIT 5: set maximum L2 rate BIT 6: set minimum L2 rate BIT 7: set transition L0 to L2 rate" ::= { adslPortBatchSet 3 } adslModeForBatchSet OBJECT-TYPE SYNTAX INTEGER { gDotLite(1), gDotDmt(2), t1Dot413(3), auto(4), etsi(5), adsl2(6), adsl2Plus(7) } MAX-ACCESS read-write STATUS current DESCRIPTION "G.lite and T1.413 are only applicable to annex A board. ETSI is only applicable to annex B board." ::= { adslPortBatchSet 4 } adslLineProfileForBatchSet OBJECT-TYPE SYNTAX DisplayString (SIZE (1..31)) MAX-ACCESS read-write STATUS current DESCRIPTION "The ADSL line profile." ::= { adslPortBatchSet 5 } adslAlarmProfileForBatchSet OBJECT-TYPE SYNTAX DisplayString (SIZE (1..31)) MAX-ACCESS read-write STATUS current DESCRIPTION "The ADSL alarm profile." ::= { adslPortBatchSet 6 } adslOptionMaskForBatchSet OBJECT-TYPE SYNTAX INTEGER MAX-ACCESS read-write STATUS current DESCRIPTION "The semantic for each bit is identical to the object adslLineConfOptionMask." ::= { adslPortBatchSet 7 } adslAturMaxTxPowerForBatchSet OBJECT-TYPE SYNTAX INTEGER (-130..200) UNITS "tenth dBm" MAX-ACCESS read-write STATUS current DESCRIPTION "The maximum allowed transmit power of ATU-R." ::= { adslPortBatchSet 8 } adslAtucMaxTxPowerForBatchSet OBJECT-TYPE SYNTAX INTEGER (-50..200) UNITS "tenth dBm" MAX-ACCESS read-write STATUS current DESCRIPTION "The maximum allowed transmit power of ATU-C." ::= { adslPortBatchSet 9 } adslMaxRxPowerForBatchSet OBJECT-TYPE SYNTAX INTEGER (-255..255) UNITS "tenth dBm" MAX-ACCESS read-write STATUS current DESCRIPTION "The maximum aggregate received power." ::= { adslPortBatchSet 10 } adslAturCarrierMaskForBatchSet OBJECT-TYPE SYNTAX OCTET STRING MAX-ACCESS read-write STATUS current DESCRIPTION "The upstream carrier mask.For CTLM AnnexA solution, bin is from 0 to 31; CTLM AnnexB solution, bin is from 0 to 63; BCM solution, bin is from 0 to 63. Bit set to 1 indicates the bin is masked off." ::= { adslPortBatchSet 11 } adslAtucCarrierMask0ForBatchSet OBJECT-TYPE SYNTAX OCTET STRING MAX-ACCESS read-write STATUS current DESCRIPTION "The downstream carrier mask from bin 32 to 255. Bit set to 1 indicates the bin is masked off." ::= { adslPortBatchSet 12 } adslAtucCarrierMask1ForBatchSet OBJECT-TYPE SYNTAX OCTET STRING MAX-ACCESS read-write STATUS current DESCRIPTION "The downstream carrier mask from bin 256 to 511. Bit set to 1 indicates the bin is masked off." ::= { adslPortBatchSet 13 } adslAturInpForBatchSet OBJECT-TYPE SYNTAX INTEGER { zero(1), zeroPointFive(2), one(3), two(4), four(5), eight(6), sixteen(7) } MAX-ACCESS read-write STATUS current DESCRIPTION "The upstream Impulse Noise Protection minimum setting in unit of DMT symbol. For CTLM solution, user can set value from 1 ~ 4, but for BCM solution, user can set value from 1 ~ 7." ::= { adslPortBatchSet 14 } adslAtucInpForBatchSet OBJECT-TYPE SYNTAX INTEGER { zero(1), zeroPointFive(2), one(3), two(4), four(5), eight(6), sixteen(7) } MAX-ACCESS read-write STATUS current DESCRIPTION "The downstream Impulse Noise Protection minimum setting in unit of DMT symbol. For CTLM solution, user can set value from 1 ~ 4, but for BCM solution, user can set value from 1 ~ 7." ::= { adslPortBatchSet 15 } adslL0TimeForBatchSet OBJECT-TYPE SYNTAX INTEGER MAX-ACCESS read-write STATUS current DESCRIPTION "Set the minimum time in seconds that the ADSL line must stay in L0 power mode before changing to the L2 power mode. For CTLM solution, the range is 120 ~ 65535; for BCM solution, the range is 10 ~ 65535." ::= { adslPortBatchSet 16 } adslL2TimeForBatchSet OBJECT-TYPE SYNTAX INTEGER MAX-ACCESS read-write STATUS current DESCRIPTION "Set minimum time in seconds that the ADSL line must stay in the L2 power mode before reducing the power again in the L2 power mode. For CTLM solution, the range is 60 ~ 65535; for BCM solution, the range is 10 ~ 65535." ::= { adslPortBatchSet 17 } adslL2ATPRForBatchSet OBJECT-TYPE SYNTAX INTEGER UNITS "dB" MAX-ACCESS read-write STATUS current DESCRIPTION "Set the maximum Aggregate Transmit Power Reduction (ATPR) in decibels (dB) that is permitted in a L2 power reduction. The system can gradually decrease the ADSL line transmission power while it is in the L2 power mode. This is the largest individual power reduction allowed in the L2 power mode. For CTLM solution, the range is 1 ~ 5(dB); for BCM solution, the range is 0 ~ 15(dB)." ::= { adslPortBatchSet 18 } adslL2ATPRTForBatchSet OBJECT-TYPE SYNTAX INTEGER UNITS "dB" MAX-ACCESS read-write STATUS current DESCRIPTION "the maximum Aggregate Transmit Power Reduction Total (ATPRT) in decibels (dB) that is permitted in the L2 power mode. This is the total transmit power decrease that is allowed to occur in the L2 power mode. For CTLM solution, the range is 1 ~ 40(dB); for BCM solution, the range is 0 ~ 15(dB)." ::= { adslPortBatchSet 19 } adslMaxL2RateForBatchSet OBJECT-TYPE SYNTAX INTEGER UNITS "kbps" MAX-ACCESS read-write STATUS current DESCRIPTION "configured maximum L2 rate. (32~4096 Kbps, 4 Kbps resolution. For CTLM solution, 0 for system assign; for BCM solution, default:4096.)" ::= { adslPortBatchSet 20 } adslMinL2RateForBatchSet OBJECT-TYPE SYNTAX INTEGER UNITS "kbps" MAX-ACCESS read-write STATUS current DESCRIPTION "configured minimum L2 rate. (32~4096 Kbps, 4 Kbps resolution, For CTLM solution, 0 for system assign; for BCM solution, default:32.)" ::= { adslPortBatchSet 21 } adslL0toL2RateForBatchSet OBJECT-TYPE SYNTAX INTEGER UNITS "kbps" MAX-ACCESS read-write STATUS current DESCRIPTION "configured transition L0 to L2 rate. (<=min_l2rate/2 and >= 16 Kbps, For CTLM solution, 0 for system assign; for BCM solution, default:16.)" ::= { adslPortBatchSet 22 } -- Line Status adslLineStatusTable OBJECT-TYPE SYNTAX SEQUENCE OF AdslLineStatusEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "This table includes the ADSL line status." ::= { adslPort 4 } adslLineStatusEntry OBJECT-TYPE SYNTAX AdslLineStatusEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "An entry in adslLineStatusTable." INDEX { ifIndex } ::= { adslLineStatusTable 1 } AdslLineStatusEntry ::= SEQUENCE { adslLineStatusMode INTEGER, adslLineUpTime INTEGER } adslLineStatusMode OBJECT-TYPE SYNTAX INTEGER { gDotLite(1), gDotDmt(2), t1Dot413(3), etsi(4), adsl2(5), adsl2Plus(6), none(7) } MAX-ACCESS read-only STATUS current DESCRIPTION "The link up mode of the ADSL line." ::= { adslLineStatusEntry 1 } adslLineUpTime OBJECT-TYPE SYNTAX INTEGER MAX-ACCESS read-only STATUS current DESCRIPTION "The link up time of the ADSL line, in unit of seconds" ::= { adslLineStatusEntry 2 } -- Power Mgmt Parameter Table powerMgmtParamTable OBJECT-TYPE SYNTAX SEQUENCE OF PowerMgmtParamEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "This table defines L0 to L2 power transition parameters." ::= { adslPort 5 } powerMgmtParamEntry OBJECT-TYPE SYNTAX PowerMgmtParamEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "An entry in powerMgmtParamTable." INDEX { ifIndex } ::= { powerMgmtParamTable 1 } PowerMgmtParamEntry ::= SEQUENCE { powerMgmtL0Time INTEGER, powerMgmtL2Time INTEGER, powerMgmtL2Atpr INTEGER, powerMgmtL2Atprt INTEGER, powerMgmtL2MinRate INTEGER, powerMgmtL2MaxRate INTEGER, powerMgmtL2ThreshRate INTEGER } powerMgmtL0Time OBJECT-TYPE SYNTAX INTEGER UNITS "second" MAX-ACCESS read-write STATUS current DESCRIPTION "The object specifies the minimum time in L0 mode before L2 mode may be entered." ::= { powerMgmtParamEntry 1 } powerMgmtL2Time OBJECT-TYPE SYNTAX INTEGER UNITS "second" MAX-ACCESS read-write STATUS current DESCRIPTION "The object specifies the minimum time in L2 mode before trimming and in between power trims." ::= { powerMgmtParamEntry 2 } powerMgmtL2Atpr OBJECT-TYPE SYNTAX INTEGER UNITS "dB" MAX-ACCESS read-write STATUS current DESCRIPTION "The maximum Aggregate Transmit Power Reduction." ::= { powerMgmtParamEntry 3 } powerMgmtL2Atprt OBJECT-TYPE SYNTAX INTEGER UNITS "dB" MAX-ACCESS read-write STATUS current DESCRIPTION "The maximum Aggregate Transmit Power Reduction Total." ::= { powerMgmtParamEntry 4 } powerMgmtL2MinRate OBJECT-TYPE SYNTAX INTEGER UNITS "Kbps" MAX-ACCESS read-write STATUS current DESCRIPTION "The object specifies the minimum L2 rate." ::= { powerMgmtParamEntry 5 } powerMgmtL2MaxRate OBJECT-TYPE SYNTAX INTEGER UNITS "Kbps" MAX-ACCESS read-write STATUS current DESCRIPTION "The object specifies the maximum L2 rate." ::= { powerMgmtParamEntry 6 } powerMgmtL2ThreshRate OBJECT-TYPE SYNTAX INTEGER UNITS "Kbps" MAX-ACCESS read-write STATUS current DESCRIPTION "The object specifies the rate threshold that triggers the line entering L0 or L2 mode." ::= { powerMgmtParamEntry 7 } -- Power Mgmt PSD Table -- Not support in 7324 RU R4.0.2 powerMgmtPSDTable OBJECT-TYPE SYNTAX SEQUENCE OF PowerMgmtPSDEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "This table provides the PSD setting for both ATU-C and ATU-R." ::= { adslPort 6 } powerMgmtPSDEntry OBJECT-TYPE SYNTAX PowerMgmtPSDEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "An entry in powerMgmtPSDTable." INDEX { ifIndex } ::= { powerMgmtPSDTable 1 } PowerMgmtPSDEntry ::= SEQUENCE { powerMgmtAtucMaxPSD INTEGER, powerMgmtAturMaxPSD INTEGER } powerMgmtAtucMaxPSD OBJECT-TYPE SYNTAX INTEGER UNITS "0.1dBm/Hz" MAX-ACCESS read-write STATUS current DESCRIPTION "The object specifies the maximum ATU-C PSD." ::= { powerMgmtPSDEntry 1 } powerMgmtAturMaxPSD OBJECT-TYPE SYNTAX INTEGER UNITS "0.1dBm/Hz" MAX-ACCESS read-write STATUS current DESCRIPTION "The object specifies the maximum ATU-R PSD." ::= { powerMgmtPSDEntry 2 } -------------------- -- pvc -------------------- maxNumOfPvcs OBJECT-TYPE SYNTAX INTEGER MAX-ACCESS read-only STATUS current DESCRIPTION "The maximum number of PVCs which could be created on a port." ::= { pvc 1 } -- PVC Table pvcTable OBJECT-TYPE SYNTAX SEQUENCE OF PvcEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "This table includes PVC configuration." ::= { pvc 2 } pvcEntry OBJECT-TYPE SYNTAX PvcEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "An entry in pvcTable." INDEX { ifIndex, pvcVpi, pvcVci, pvcPvid } ::= { pvcTable 1 } PvcEntry ::= SEQUENCE { -- Common -- pvcVpi INTEGER, pvcVci INTEGER, pvcPvid VlanIndex, pvcPriority INTEGER, pvcProfileDS DisplayString, pvcProfileUS DisplayString, -- Only for paepvc -- --pvcPaePvid VlanIndex, --pvcPaePriority INTEGER, pvcAcName DisplayString, pvcServiceName DisplayString, pvcHelloTime INTEGER, -- Only for pvc -- --pvcSuperChannel INTEGER, -- Other -- pvcRowStatus RowStatus } -- Common -- pvcVpi OBJECT-TYPE SYNTAX INTEGER (0..255) MAX-ACCESS read-only STATUS current DESCRIPTION "VPI of the pvc." ::= { pvcEntry 1 } pvcVci OBJECT-TYPE SYNTAX INTEGER (1..65535) MAX-ACCESS read-only STATUS current DESCRIPTION "VCI of the pvc." ::= { pvcEntry 2 } pvcPvid OBJECT-TYPE SYNTAX VlanIndex MAX-ACCESS read-only STATUS current DESCRIPTION "Default VID of the pvc." ::= { pvcEntry 3 } pvcPriority OBJECT-TYPE SYNTAX INTEGER (0..7) MAX-ACCESS read-create STATUS current DESCRIPTION "802.1p default priority of the pvc." ::= { pvcEntry 5 } pvcProfileDS OBJECT-TYPE SYNTAX DisplayString (SIZE (1..31)) MAX-ACCESS read-create STATUS current DESCRIPTION "The value of this object identifies the row in the atmProfileTable, which applies for this pvc in DS side." ::= { pvcEntry 6 } -- Other -- pvcRowStatus OBJECT-TYPE SYNTAX RowStatus MAX-ACCESS read-create STATUS current DESCRIPTION "This object is used to create a new row or delete an existing row in this table." ::= { pvcEntry 7 } pvcProfileUS OBJECT-TYPE SYNTAX DisplayString (SIZE (1..31)) MAX-ACCESS read-create STATUS current DESCRIPTION "The value of this object identifies the row in the atmProfileTable, which applies for this pvc in US side." ::= { pvcEntry 8 } -- Only for PAEPVC -- --pvcPaePvid OBJECT-TYPE --SYNTAX VlanIndex --MAX-ACCESS read-only --STATUS current --DESCRIPTION --"Default P-VID for paepvc." --::= { pvcEntry 9 } --pvcPaePriority OBJECT-TYPE --SYNTAX INTEGER (0..7) --MAX-ACCESS read-only --STATUS current --DESCRIPTION --"802.1p default Pae-priority for paepvc." --::= { pvcEntry 10 } pvcAcName OBJECT-TYPE SYNTAX DisplayString MAX-ACCESS read-create STATUS current DESCRIPTION "Access concentrator name for paepvc." ::= { pvcEntry 11 } pvcServiceName OBJECT-TYPE SYNTAX DisplayString MAX-ACCESS read-create STATUS current DESCRIPTION "Service name for paepvc." ::= { pvcEntry 12 } pvcHelloTime OBJECT-TYPE SYNTAX INTEGER UNITS "second" MAX-ACCESS read-create STATUS current DESCRIPTION "The system will close the PVC if there are not any LCP echo messages passed through during the LCP hello time." ::= { pvcEntry 13 } -- Only for PVC -- --pvcSuperChannel OBJECT-TYPE --SYNTAX INTEGER { --enable(1), --disable(2) --} --MAX-ACCESS read-create --STATUS current --DESCRIPTION --"Specified the configured PVC is a super channel." --::= { pvcEntry 14 } -- PVC state -- pvcStateTable OBJECT-TYPE SYNTAX SEQUENCE OF PvcStateEntry MAX-ACCESS read-only STATUS current DESCRIPTION "This table show current PVC status." ::= { pvc 3 } pvcStateEntry OBJECT-TYPE SYNTAX PvcStateEntry MAX-ACCESS read-only STATUS current DESCRIPTION "An entry in pvcStateTable." INDEX { ifIndex, pvcStateVpi, pvcStateVci, pvcStatePvid } ::= { pvcStateTable 1 } PvcStateEntry ::= SEQUENCE { pvcStateVpi INTEGER, pvcStateVci INTEGER, pvcStatePvid VlanIndex, pvcStatePriority INTEGER, --pvcStateCvid VlanIndex, --pvcStateCPriority INTEGER, --pvcStateMode DisplayString, pvcStateChannelType DisplayString, pvcStateEncap DisplayString } pvcStateVpi OBJECT-TYPE SYNTAX INTEGER (0..255) MAX-ACCESS read-only STATUS current DESCRIPTION "VPI of the pvc." ::= { pvcStateEntry 1 } pvcStateVci OBJECT-TYPE SYNTAX INTEGER (1..65535) MAX-ACCESS read-only STATUS current DESCRIPTION "VCI of the pvc." ::= { pvcStateEntry 2 } pvcStatePvid OBJECT-TYPE SYNTAX VlanIndex MAX-ACCESS read-only STATUS current DESCRIPTION "Default VID of the pvc." ::= { pvcStateEntry 3 } pvcStatePriority OBJECT-TYPE SYNTAX INTEGER (0..7) MAX-ACCESS read-only STATUS current DESCRIPTION "802.1p default priority of the pvc." ::= { pvcStateEntry 4 } --pvcStateCvid OBJECT-TYPE --SYNTAX VlanIndex --MAX-ACCESS read-only --STATUS current --DESCRIPTION --"Default C-VID for paepvc." --::= { pvcStateEntry 5 } --pvcStateCPriority OBJECT-TYPE --SYNTAX INTEGER (0..7) --MAX-ACCESS read-only --STATUS current --DESCRIPTION --"802.1p default C-priority for paepvc." --::= { pvcStateEntry 6 } --pvcStateMode OBJECT-TYPE --SYNTAX DisplayString (SIZE (1..31)) --MAX-ACCESS read-only --STATUS current --DESCRIPTION --"The value of this object identifies the link mode at runntime." --::= { pvcStateEntry 7 } pvcStateChannelType OBJECT-TYPE SYNTAX DisplayString (SIZE (1..31)) MAX-ACCESS read-only STATUS current DESCRIPTION "The value of this object identifies the channel type at runtime." ::= { pvcStateEntry 8 } pvcStateEncap OBJECT-TYPE SYNTAX DisplayString (SIZE (1..31)) MAX-ACCESS read-only STATUS current DESCRIPTION "The value of this object identifies the channel encapsulation at runtime." ::= { pvcStateEntry 9 } -- Upstream Rate Limit Table pvcUsRateLimitTable OBJECT-TYPE SYNTAX SEQUENCE OF PvcUsRateLimitEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "This table defines the upstream rate limit for each PVC." ::= { pvc 4 } pvcUsRateLimitEntry OBJECT-TYPE SYNTAX PvcUsRateLimitEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "An entry in pvcUsRateLimitTable." INDEX { ifIndex, pvcVpi, pvcVci } ::= { pvcUsRateLimitTable 1 } PvcUsRateLimitEntry ::= SEQUENCE { pvcUsRateLimitEnable INTEGER, pvcUsRateLimit INTEGER } pvcUsRateLimitEnable OBJECT-TYPE SYNTAX INTEGER { enable(1), disable(2) } MAX-ACCESS read-write STATUS current DESCRIPTION "Enable/disable upstream rate limit for a PVC." ::= { pvcUsRateLimitEntry 1 } pvcUsRateLimit OBJECT-TYPE SYNTAX INTEGER UNITS "Kbps" MAX-ACCESS read-write STATUS current DESCRIPTION "Upstream rate limit in Kbps for a PVC." ::= { pvcUsRateLimitEntry 2 } -------------------- -- priority pvc -------------------- maxNumOfPriorityPvcs OBJECT-TYPE SYNTAX INTEGER MAX-ACCESS read-only STATUS current DESCRIPTION "The maximum number of priority PVCs which could be created on a port." ::= { ppvc 1 } -- Priority PVC Table ppvcTable OBJECT-TYPE SYNTAX SEQUENCE OF PpvcEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "This table includes priority PVC configuration." ::= { ppvc 2 } ppvcEntry OBJECT-TYPE SYNTAX PpvcEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "An entry in ppvcTable." INDEX { ifIndex, ppvcVpi, ppvcVci, ppvcPvid } ::= { ppvcTable 1 } PpvcEntry ::= SEQUENCE { ppvcVpi INTEGER, ppvcVci INTEGER, ppvcPvid VlanIndex, ppvcEncap INTEGER, ppvcPriority INTEGER, ppvcRowStatus RowStatus } ppvcVpi OBJECT-TYPE SYNTAX INTEGER (0..255) MAX-ACCESS read-only STATUS current DESCRIPTION "VPI of the ppvc." ::= { ppvcEntry 1 } ppvcVci OBJECT-TYPE SYNTAX INTEGER (1..65535) MAX-ACCESS read-only STATUS current DESCRIPTION "VCI of the ppvc." ::= { ppvcEntry 2 } ppvcPvid OBJECT-TYPE SYNTAX VlanIndex MAX-ACCESS read-only STATUS current DESCRIPTION "Default VID of the ppvc." ::= { ppvcEntry 3 } ppvcEncap OBJECT-TYPE SYNTAX INTEGER { llc(1), vc(2) } MAX-ACCESS read-create STATUS current DESCRIPTION "Encapsulation of the ppvc." ::= { ppvcEntry 4 } ppvcPriority OBJECT-TYPE SYNTAX INTEGER (0..7) MAX-ACCESS read-create STATUS current DESCRIPTION "802.1p default priority of the ppvc." ::= { ppvcEntry 5 } ppvcRowStatus OBJECT-TYPE SYNTAX RowStatus MAX-ACCESS read-create STATUS current DESCRIPTION "This object is used to create a new row or delete an existing row in this table." ::= { ppvcEntry 6 } -- Priority PVC Member Table ppvcMemberTable OBJECT-TYPE SYNTAX SEQUENCE OF PpvcMemberEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "This table includes priority PVC member configuration." ::= { ppvc 4 } ppvcMemberEntry OBJECT-TYPE SYNTAX PpvcMemberEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "An entry in ppvcMemberTable." INDEX { ifIndex, ppvcVpi, ppvcVci, ppvcMemberVpi, ppvcMemberVci, ppvcMemberPriority } ::= { ppvcMemberTable 1 } PpvcMemberEntry ::= SEQUENCE { ppvcMemberVpi INTEGER, ppvcMemberVci INTEGER, ppvcMemberPriority INTEGER, ppvcMemberProfileDS DisplayString, ppvcMemberRowStatus RowStatus, ppvcMemberProfileUS DisplayString } ppvcMemberVpi OBJECT-TYPE SYNTAX INTEGER (0..255) MAX-ACCESS read-only STATUS current DESCRIPTION "VPI of the member ppvc." ::= { ppvcMemberEntry 1 } ppvcMemberVci OBJECT-TYPE SYNTAX INTEGER (1..65535) MAX-ACCESS read-only STATUS current DESCRIPTION "VCI of the member ppvc." ::= { ppvcMemberEntry 2 } ppvcMemberPriority OBJECT-TYPE SYNTAX INTEGER (0..7) MAX-ACCESS read-only STATUS current DESCRIPTION "802.1p default priority of the member ppvc." ::= { ppvcMemberEntry 3 } ppvcMemberProfileDS OBJECT-TYPE SYNTAX DisplayString (SIZE (1..31)) MAX-ACCESS read-create STATUS current DESCRIPTION "The profile of the member ppvc in DS side." ::= { ppvcMemberEntry 4 } ppvcMemberRowStatus OBJECT-TYPE SYNTAX RowStatus MAX-ACCESS read-create STATUS current DESCRIPTION "This object is used to create a new row or delete an existing row in this table." ::= { ppvcMemberEntry 5 } ppvcMemberProfileUS OBJECT-TYPE SYNTAX DisplayString (SIZE (1..31)) MAX-ACCESS read-create STATUS current DESCRIPTION "The profile of the member ppvc in US side." ::= { ppvcMemberEntry 6 } ------------------------------- -- 2684 routed mode pvc (rpvc) ------------------------------- -- Routed Gateway Table rpvcGatewayTable OBJECT-TYPE SYNTAX SEQUENCE OF RpvcGatewayEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "This table includes Routed Gateway configuration." ::= { rpvc 1 } rpvcGatewayEntry OBJECT-TYPE SYNTAX RpvcGatewayEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "An entry in Routed Gateway table." INDEX { rpvcGatewayIp } ::= { rpvcGatewayTable 1 } RpvcGatewayEntry ::= SEQUENCE { rpvcGatewayIp IpAddress, rpvcGatewayVlanId VlanIndex, rpvcGatewayRowStatus RowStatus, rpvcGatewayPriority INTEGER } rpvcGatewayIp OBJECT-TYPE SYNTAX IpAddress MAX-ACCESS read-only STATUS current DESCRIPTION "IP of RPVC gateway." ::= { rpvcGatewayEntry 1 } rpvcGatewayVlanId OBJECT-TYPE SYNTAX VlanIndex MAX-ACCESS read-write STATUS current DESCRIPTION "Vlan id send to this RPVC gateway." ::= { rpvcGatewayEntry 2 } rpvcGatewayRowStatus OBJECT-TYPE SYNTAX RowStatus MAX-ACCESS read-create STATUS current DESCRIPTION "This object is used to create a new row or delete an existing row in this table." ::= { rpvcGatewayEntry 3 } rpvcGatewayPriority OBJECT-TYPE SYNTAX INTEGER MAX-ACCESS read-write STATUS current DESCRIPTION "802.1p p bit send to this RPVC gateway." ::= { rpvcGatewayEntry 4 } -- Routed PVC Table rpvcTable OBJECT-TYPE SYNTAX SEQUENCE OF RpvcEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "This table includes RPVC configuration." ::= { rpvc 2 } rpvcEntry OBJECT-TYPE SYNTAX RpvcEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "An entry in rpvcTable." INDEX { ifIndex, rpvcVpi, rpvcVci, rpvcIp, rpvcNetmask } ::= { rpvcTable 1 } RpvcEntry ::= SEQUENCE { rpvcVpi INTEGER, rpvcVci INTEGER, rpvcDSProfile DisplayString, rpvcUSProfile DisplayString, rpvcIp IpAddress, rpvcNetmask IpAddress, rpvcGatewayIpAddress IpAddress, rpvcRowStatus RowStatus } rpvcVpi OBJECT-TYPE SYNTAX INTEGER (0..255) MAX-ACCESS read-only STATUS current DESCRIPTION "VPI of the rpvc." ::= { rpvcEntry 1 } rpvcVci OBJECT-TYPE SYNTAX INTEGER (1..65535) MAX-ACCESS read-only STATUS current DESCRIPTION "VCI of the rpvc." ::= { rpvcEntry 2 } rpvcDSProfile OBJECT-TYPE SYNTAX DisplayString (SIZE (1..31)) MAX-ACCESS read-create STATUS current DESCRIPTION "The down stream profile of the rpvc." ::= { rpvcEntry 3 } rpvcUSProfile OBJECT-TYPE SYNTAX DisplayString (SIZE (1..31)) MAX-ACCESS read-create STATUS current DESCRIPTION "The up stream profile of the rpvc." ::= { rpvcEntry 4 } rpvcIp OBJECT-TYPE SYNTAX IpAddress MAX-ACCESS read-only STATUS current DESCRIPTION "The IP of the rpvc." ::= { rpvcEntry 5 } rpvcNetmask OBJECT-TYPE SYNTAX IpAddress MAX-ACCESS read-only STATUS current DESCRIPTION "The IP mask of the rpvc IP." ::= { rpvcEntry 6 } rpvcGatewayIpAddress OBJECT-TYPE SYNTAX IpAddress MAX-ACCESS read-create STATUS current DESCRIPTION "The gateway IP of rpvc." ::= { rpvcEntry 7 } rpvcRowStatus OBJECT-TYPE SYNTAX RowStatus MAX-ACCESS read-create STATUS current DESCRIPTION "This object is used to create a new row or delete an existing row in this table." ::= { rpvcEntry 8 } -- Routed PVC Routed Domain Table rpvcRouteDomainTable OBJECT-TYPE SYNTAX SEQUENCE OF RpvcRouteDomainEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "This table includes RPVC route domain configuration." ::= { rpvc 3 } rpvcRouteDomainEntry OBJECT-TYPE SYNTAX RpvcRouteDomainEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "An entry in rpvcRouteDomainTable." INDEX { ifIndex, rpvcRouteDomainVpi, rpvcRouteDomainVci, rpvcRouteDomainIp, rpvcRouteDomainNetmask } ::= { rpvcRouteDomainTable 1 } RpvcRouteDomainEntry ::= SEQUENCE { rpvcRouteDomainVpi INTEGER, rpvcRouteDomainVci INTEGER, rpvcRouteDomainIp IpAddress, rpvcRouteDomainNetmask IpAddress, rpvcRouteDomainRowStatus RowStatus } rpvcRouteDomainVpi OBJECT-TYPE SYNTAX INTEGER (0..255) MAX-ACCESS read-only STATUS current DESCRIPTION "VPI of the rpvc." ::= { rpvcRouteDomainEntry 1 } rpvcRouteDomainVci OBJECT-TYPE SYNTAX INTEGER (1..65535) MAX-ACCESS read-only STATUS current DESCRIPTION "VCI of the rpvc." ::= { rpvcRouteDomainEntry 2 } rpvcRouteDomainIp OBJECT-TYPE SYNTAX IpAddress MAX-ACCESS read-only STATUS current DESCRIPTION "The route domain IP." ::= { rpvcRouteDomainEntry 3 } rpvcRouteDomainNetmask OBJECT-TYPE SYNTAX IpAddress MAX-ACCESS read-only STATUS current DESCRIPTION "The IP mask of the route domain IP." ::= { rpvcRouteDomainEntry 4 } rpvcRouteDomainRowStatus OBJECT-TYPE SYNTAX RowStatus MAX-ACCESS read-create STATUS current DESCRIPTION "This object is used to create a new row or delete an existing row in this table." ::= { rpvcRouteDomainEntry 5 } rpvcArpAgingTime OBJECT-TYPE SYNTAX INTEGER MAX-ACCESS read-write STATUS current DESCRIPTION "Set RPVC ARP proxy aging time 10..10000 seconds, 0 to disable againg." ::= { rpvc 4 } rpvcArpFlush OBJECT-TYPE SYNTAX INTEGER { enable(1) } MAX-ACCESS read-write STATUS current DESCRIPTION "Flush the RPVC ARP proxy table." ::= { rpvc 5 } -------------------- -- dsBcastDisableTable -------------------- dsBcastDisableTable OBJECT-TYPE SYNTAX SEQUENCE OF DsBcastDisableEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "This table includes Down Stream Bcast configuration." ::= { port 9 } dsBcastDisableEntry OBJECT-TYPE SYNTAX DsBcastDisableEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "An entry in Down Stream Bcast table." INDEX { ifIndex, dsBcastDisableVlanId } ::= { dsBcastDisableTable 1 } DsBcastDisableEntry ::= SEQUENCE { dsBcastDisableVlanId INTEGER, dsBcastDisableRowStatus RowStatus } dsBcastDisableVlanId OBJECT-TYPE SYNTAX INTEGER MAX-ACCESS read-only STATUS current DESCRIPTION "downstream broadcast disabled vid." ::= { dsBcastDisableEntry 1 } dsBcastDisableRowStatus OBJECT-TYPE SYNTAX RowStatus MAX-ACCESS read-create STATUS current DESCRIPTION "This object is used to create a new row or delete an existing row in this table." ::= { dsBcastDisableEntry 2 } -------------------- -- paepvc -------------------- -- PPPoAoE PVC Table paepvcTable OBJECT-TYPE SYNTAX SEQUENCE OF PaepvcEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "This table includes PPPoAoE PVC configuration." ::= { paepvc 1 } paepvcEntry OBJECT-TYPE SYNTAX PaepvcEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "An entry of paepvcTable." INDEX { ifIndex, paepvcVpi, paepvcVci, paepvcPvid } ::= { paepvcTable 1 } PaepvcEntry ::= SEQUENCE { paepvcVpi INTEGER, paepvcVci INTEGER, paepvcPvid VlanIndex, paepvcPriority INTEGER, paepvcProfileDS DisplayString, paepvcAcName DisplayString, paepvcServiceName DisplayString, paepvcHelloTime INTEGER, paepvcRowStatus RowStatus, paepvcProfileUS DisplayString, paepvcCvid VlanIndex, paepvcCPriority INTEGER } paepvcVpi OBJECT-TYPE SYNTAX INTEGER (0..255) MAX-ACCESS read-only STATUS current DESCRIPTION "VPI of the pvc." ::= { paepvcEntry 1 } paepvcVci OBJECT-TYPE SYNTAX INTEGER (1..65535) MAX-ACCESS read-only STATUS current DESCRIPTION "VCI of the pvc." ::= { paepvcEntry 2 } paepvcPvid OBJECT-TYPE SYNTAX VlanIndex MAX-ACCESS read-only STATUS current DESCRIPTION "Default VID of the pvc." ::= { paepvcEntry 3 } paepvcPriority OBJECT-TYPE SYNTAX INTEGER (0..7) MAX-ACCESS read-create STATUS current DESCRIPTION "802.1p default priority of the pvc." ::= { paepvcEntry 5 } paepvcProfileDS OBJECT-TYPE SYNTAX DisplayString (SIZE (1..31)) MAX-ACCESS read-create STATUS current DESCRIPTION "The value of this object identifies the row in the atmProfileTable, which applies for this pvc in DS side." ::= { paepvcEntry 6 } paepvcAcName OBJECT-TYPE SYNTAX DisplayString MAX-ACCESS read-create STATUS current DESCRIPTION "Access concentrator name." ::= { paepvcEntry 7 } paepvcServiceName OBJECT-TYPE SYNTAX DisplayString MAX-ACCESS read-create STATUS current DESCRIPTION "Service name." ::= { paepvcEntry 8 } paepvcHelloTime OBJECT-TYPE SYNTAX INTEGER UNITS "second" MAX-ACCESS read-create STATUS current DESCRIPTION "The system will close the PVC if there are not any LCP echo messages passed through during the LCP hello time." ::= { paepvcEntry 9 } paepvcRowStatus OBJECT-TYPE SYNTAX RowStatus MAX-ACCESS read-create STATUS current DESCRIPTION "This object is used to create a new row or delete an existing row in this table." ::= { paepvcEntry 10 } paepvcProfileUS OBJECT-TYPE SYNTAX DisplayString (SIZE (1..31)) MAX-ACCESS read-create STATUS current DESCRIPTION "The value of this object identifies the row in the atmProfileTable, which applies for this pvc in US side." ::= { paepvcEntry 11 } paepvcCvid OBJECT-TYPE SYNTAX VlanIndex MAX-ACCESS read-create STATUS current DESCRIPTION "Default C-VID of the pvc." ::= { paepvcEntry 12 } paepvcCPriority OBJECT-TYPE SYNTAX INTEGER (0..7) MAX-ACCESS read-create STATUS current DESCRIPTION "802.1p default C-priority of the pvc." ::= { paepvcEntry 13 } -------------------- -- tlspvc -------------------- -- TLS PVC Table tlspvcTable OBJECT-TYPE SYNTAX SEQUENCE OF TlspvcEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "This table includes Transparent LAN Service (TLS) PVC configuration." ::= { tlspvc 1 } tlspvcEntry OBJECT-TYPE SYNTAX TlspvcEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "An entry of tlspvcTable." INDEX { ifIndex, tlspvcVpi, tlspvcVci, tlspvcSvid } ::= { tlspvcTable 1 } TlspvcEntry ::= SEQUENCE { tlspvcVpi INTEGER, tlspvcVci INTEGER, tlspvcSvid VlanIndex, tlspvcSpriority INTEGER, tlspvcProfileDS DisplayString, tlspvcRowStatus RowStatus, tlspvcProfileUS DisplayString } tlspvcVpi OBJECT-TYPE SYNTAX INTEGER (0..255) MAX-ACCESS read-only STATUS current DESCRIPTION "VPI of the pvc." ::= { tlspvcEntry 1 } tlspvcVci OBJECT-TYPE SYNTAX INTEGER (1..65535) MAX-ACCESS read-only STATUS current DESCRIPTION "VCI of the pvc." ::= { tlspvcEntry 2 } tlspvcSvid OBJECT-TYPE SYNTAX VlanIndex MAX-ACCESS read-only STATUS current DESCRIPTION "s-tag VLAN ID of the pvc." ::= { tlspvcEntry 3 } tlspvcSpriority OBJECT-TYPE SYNTAX INTEGER (0..7) MAX-ACCESS read-create STATUS current DESCRIPTION "s-tag priority of the pvc." ::= { tlspvcEntry 5 } tlspvcProfileDS OBJECT-TYPE SYNTAX DisplayString (SIZE (1..31)) MAX-ACCESS read-create STATUS current DESCRIPTION "The value of this object identifies the row in the atmProfileTable, which applies for this pvc in DS side." ::= { tlspvcEntry 6 } tlspvcRowStatus OBJECT-TYPE SYNTAX RowStatus MAX-ACCESS read-create STATUS current DESCRIPTION "This object is used to create a new row or delete an existing row in this table." ::= { tlspvcEntry 7 } tlspvcProfileUS OBJECT-TYPE SYNTAX DisplayString (SIZE (1..31)) MAX-ACCESS read-create STATUS current DESCRIPTION "The value of this object identifies the row in the atmProfileTable, which applies for this pvc in US side." ::= { tlspvcEntry 8 } -------------------- -- ipbpvc -------------------- -- Domain Table ipbpvcDomainTable OBJECT-TYPE SYNTAX SEQUENCE OF IpbpvcDomainEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "This table includes ipbpvc domain configuration. This table is supported by R3.00 and later versions." ::= { ipbpvc 1 } ipbpvcDomainEntry OBJECT-TYPE SYNTAX IpbpvcDomainEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "An entry of ipbpvcDomainTable." INDEX { ipbpvcDomainName } ::= { ipbpvcDomainTable 1 } IpbpvcDomainEntry ::= SEQUENCE { ipbpvcDomainName OCTET STRING, ipbpvcDomainRowStatus RowStatus } ipbpvcDomainName OBJECT-TYPE SYNTAX OCTET STRING MAX-ACCESS read-only STATUS current DESCRIPTION "Name of the domain." ::= { ipbpvcDomainEntry 1 } ipbpvcDomainRowStatus OBJECT-TYPE SYNTAX RowStatus MAX-ACCESS read-create STATUS current DESCRIPTION "Row status of the table." ::= { ipbpvcDomainEntry 2 } -- Domain VLAN Table ipbpvcDomainVlanTable OBJECT-TYPE SYNTAX SEQUENCE OF IpbpvcDomainVlanEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "This table includes ipbpvc domain VLAN configuration. This table is supported by R3.00 and later versions." ::= { ipbpvc 2 } ipbpvcDomainVlanEntry OBJECT-TYPE SYNTAX IpbpvcDomainVlanEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "An entry of ipbpvcDomainVlanTable." INDEX { ipbpvcDomainName, ipbpvcDomainVlanId } ::= { ipbpvcDomainVlanTable 1 } IpbpvcDomainVlanEntry ::= SEQUENCE { ipbpvcDomainVlanId VlanIndex, ipbpvcDomainDhcpVlanEnable INTEGER, ipbpvcDomainVlanRowStatus RowStatus } ipbpvcDomainVlanId OBJECT-TYPE SYNTAX VlanIndex MAX-ACCESS read-only STATUS current DESCRIPTION "Set VLAN to join or leave the specified domain." ::= { ipbpvcDomainVlanEntry 1 } ipbpvcDomainDhcpVlanEnable OBJECT-TYPE SYNTAX INTEGER { enable(1), disable(2) } MAX-ACCESS read-create STATUS current DESCRIPTION "Enable/disable DHCP VLAN in a domain." ::= { ipbpvcDomainVlanEntry 2 } ipbpvcDomainVlanRowStatus OBJECT-TYPE SYNTAX RowStatus MAX-ACCESS read-create STATUS current DESCRIPTION "Row status of the table used to create/delete an entry." ::= { ipbpvcDomainVlanEntry 3 } -- Edge Router Table ipbpvcEdgeRouterTable OBJECT-TYPE SYNTAX SEQUENCE OF IpbpvcEdgeRouterEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "This table includes ipbpvc edge router configuration. This table is supported by R3.00 and later versions." ::= { ipbpvc 3 } ipbpvcEdgeRouterEntry OBJECT-TYPE SYNTAX IpbpvcEdgeRouterEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "An entry of ipbpvcEdgeRouterTable." INDEX { ipbpvcDomainName, ipbpvcEdgeRouterIp, ipbpvcEdgeRouterMask, ipbpvcEdgeRouterVid } ::= { ipbpvcEdgeRouterTable 1 } IpbpvcEdgeRouterEntry ::= SEQUENCE { ipbpvcEdgeRouterIp IpAddress, ipbpvcEdgeRouterMask INTEGER, ipbpvcEdgeRouterVid VlanIndex, ipbpvcEdgeRouterRowStatus RowStatus } ipbpvcEdgeRouterIp OBJECT-TYPE SYNTAX IpAddress MAX-ACCESS read-only STATUS current DESCRIPTION "IP address of the edge router." ::= { ipbpvcEdgeRouterEntry 1 } ipbpvcEdgeRouterVid OBJECT-TYPE SYNTAX VlanIndex MAX-ACCESS read-only STATUS current DESCRIPTION "VLAN ID of the edge router." ::= { ipbpvcEdgeRouterEntry 2 } ipbpvcEdgeRouterMask OBJECT-TYPE SYNTAX INTEGER MAX-ACCESS read-only STATUS current DESCRIPTION "Netmask of the edge router." ::= { ipbpvcEdgeRouterEntry 3 } ipbpvcEdgeRouterRowStatus OBJECT-TYPE SYNTAX RowStatus MAX-ACCESS read-create STATUS current DESCRIPTION "Row status of the table used to create/delete an entry." ::= { ipbpvcEdgeRouterEntry 4 } -- Interface Table ipbpvcInterfaceTable OBJECT-TYPE SYNTAX SEQUENCE OF IpbpvcInterfaceEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "This table includes ipbpvc interface configuration. This table is supported by R3.00 and later versions." ::= { ipbpvc 4 } ipbpvcInterfaceEntry OBJECT-TYPE SYNTAX IpbpvcInterfaceEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "An entry of ipbpvcInterfaceTable." INDEX { ipbpvcDomainName, ipbpvcInterfaceIp, ipbpvcInterfaceMask, ipbpvcInterfaceVid } ::= { ipbpvcInterfaceTable 1 } IpbpvcInterfaceEntry ::= SEQUENCE { ipbpvcInterfaceIp IpAddress, ipbpvcInterfaceMask INTEGER, ipbpvcInterfaceVid VlanIndex, ipbpvcInterfaceIfIndex INTEGER, ipbpvcInterfaceVpi INTEGER, ipbpvcInterfaceVci INTEGER, ipbpvcInterfaceRowStatus RowStatus } ipbpvcInterfaceIp OBJECT-TYPE SYNTAX IpAddress MAX-ACCESS read-only STATUS current DESCRIPTION "IP address of the interface." ::= { ipbpvcInterfaceEntry 1 } ipbpvcInterfaceMask OBJECT-TYPE SYNTAX INTEGER MAX-ACCESS read-only STATUS current DESCRIPTION "Netmask of the interface." ::= { ipbpvcInterfaceEntry 2 } ipbpvcInterfaceVid OBJECT-TYPE SYNTAX VlanIndex MAX-ACCESS read-only STATUS current DESCRIPTION "VLAN ID of the interface." ::= { ipbpvcInterfaceEntry 3 } ipbpvcInterfaceIfIndex OBJECT-TYPE SYNTAX INTEGER MAX-ACCESS read-create STATUS current DESCRIPTION "IfIndex of the interface." ::= { ipbpvcInterfaceEntry 4 } ipbpvcInterfaceVpi OBJECT-TYPE SYNTAX INTEGER MAX-ACCESS read-create STATUS current DESCRIPTION "VPI of the interface." ::= { ipbpvcInterfaceEntry 5 } ipbpvcInterfaceVci OBJECT-TYPE SYNTAX INTEGER MAX-ACCESS read-create STATUS current DESCRIPTION "VCI of the interface." ::= { ipbpvcInterfaceEntry 6 } ipbpvcInterfaceRowStatus OBJECT-TYPE SYNTAX RowStatus MAX-ACCESS read-create STATUS current DESCRIPTION "Row status of the table used to create/delete an entry." ::= { ipbpvcInterfaceEntry 7 } -- Route Table ipbpvcRouteTable OBJECT-TYPE SYNTAX SEQUENCE OF IpbpvcRouteEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "This table includes ipbpvc route configuration. This table is supported by R3.00 and later versions." ::= { ipbpvc 5 } ipbpvcRouteEntry OBJECT-TYPE SYNTAX IpbpvcRouteEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "An entry of ipbpvcRouteTable." INDEX { ipbpvcDomainName, ipbpvcRouteIp, ipbpvcRouteMask, ipbpvcRouteNextHop } ::= { ipbpvcRouteTable 1 } IpbpvcRouteEntry ::= SEQUENCE { ipbpvcRouteIp IpAddress, ipbpvcRouteMask INTEGER, ipbpvcRouteNextHop IpAddress, ipbpvcRouteMetric INTEGER, ipbpvcRoutePriority INTEGER, ipbpvcRouteRowStatus RowStatus } ipbpvcRouteIp OBJECT-TYPE SYNTAX IpAddress MAX-ACCESS read-only STATUS current DESCRIPTION "IP address of the route." ::= { ipbpvcRouteEntry 1 } ipbpvcRouteMask OBJECT-TYPE SYNTAX INTEGER MAX-ACCESS read-only STATUS current DESCRIPTION "Netmask of the route." ::= { ipbpvcRouteEntry 2 } ipbpvcRouteNextHop OBJECT-TYPE SYNTAX IpAddress MAX-ACCESS read-only STATUS current DESCRIPTION "Next hop IP address of the route." ::= { ipbpvcRouteEntry 3 } ipbpvcRouteMetric OBJECT-TYPE SYNTAX INTEGER (1..15) MAX-ACCESS read-create STATUS current DESCRIPTION "Metric of the route." ::= { ipbpvcRouteEntry 4 } ipbpvcRoutePriority OBJECT-TYPE SYNTAX INTEGER MAX-ACCESS read-create STATUS current DESCRIPTION "Priority of the route. Note that the default value of this object is 8, which means we keep the original priority of the packet(frame)." ::= { ipbpvcRouteEntry 5 } ipbpvcRouteRowStatus OBJECT-TYPE SYNTAX RowStatus MAX-ACCESS read-create STATUS current DESCRIPTION "Row status of the table used to create/delete an entry." ::= { ipbpvcRouteEntry 6 } -- PVC Table ipbpvcTable OBJECT-TYPE SYNTAX SEQUENCE OF IpbpvcEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "This table includes ipbpvc configuration. This table is supported by R3.00 and later versions." ::= { ipbpvc 6 } ipbpvcEntry OBJECT-TYPE SYNTAX IpbpvcEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "An entry of ipbpvcTable." INDEX { ifIndex, ipbpvcVpi, ipbpvcVci, ipbpvcPvid } ::= { ipbpvcTable 1 } IpbpvcEntry ::= SEQUENCE { ipbpvcVpi INTEGER, ipbpvcVci INTEGER, ipbpvcPvid INTEGER, ipbpvcEncap INTEGER, ipbpvcPriority INTEGER, ipbpvcProfile OCTET STRING, ipbpvcRowStatus RowStatus, ipbpvcProfileUS OCTET STRING } ipbpvcVpi OBJECT-TYPE SYNTAX INTEGER MAX-ACCESS read-only STATUS current DESCRIPTION "VPI of the PVC." ::= { ipbpvcEntry 1 } ipbpvcVci OBJECT-TYPE SYNTAX INTEGER MAX-ACCESS read-only STATUS current DESCRIPTION "VCI of the PVC." ::= { ipbpvcEntry 2 } ipbpvcPvid OBJECT-TYPE SYNTAX INTEGER MAX-ACCESS read-only STATUS current DESCRIPTION "PVID of the PVC." ::= { ipbpvcEntry 3 } ipbpvcEncap OBJECT-TYPE SYNTAX INTEGER { ipoe(1), reserved(2), ipoa(3) } MAX-ACCESS read-create STATUS current DESCRIPTION "Type of the PVC." ::= { ipbpvcEntry 4 } ipbpvcPriority OBJECT-TYPE SYNTAX INTEGER (0..7) MAX-ACCESS read-create STATUS current DESCRIPTION "Priority of the PVC." ::= { ipbpvcEntry 5 } ipbpvcProfile OBJECT-TYPE SYNTAX OCTET STRING MAX-ACCESS read-create STATUS current DESCRIPTION "Profile of the PVC." ::= { ipbpvcEntry 6 } ipbpvcRowStatus OBJECT-TYPE SYNTAX INTEGER MAX-ACCESS read-create STATUS current DESCRIPTION "Row status of the table used to create/delete an entry." ::= { ipbpvcEntry 7 } ipbpvcProfileUS OBJECT-TYPE SYNTAX OCTET STRING MAX-ACCESS read-create STATUS current DESCRIPTION "US Profile of the PVC." ::= { ipbpvcEntry 8 } -- ARP Proxy arpproxy OBJECT IDENTIFIER ::= { ipbpvc 8 } arpproxyAge OBJECT-TYPE SYNTAX INTEGER (10..10000) UNITS "second" MAX-ACCESS read-write STATUS current DESCRIPTION "Aging time of the ARP proxy. This object is supported by R3.00 and later versions." ::= { arpproxy 1 } arpproxyFlush OBJECT IDENTIFIER ::= { arpproxy 2 } arpproxyFlushTarget OBJECT-TYPE SYNTAX INTEGER { all(1), edgerouter(2), interface(3) } MAX-ACCESS read-write STATUS current DESCRIPTION "The target whose ARP table to be flushed. This object is supported by R3.00 and later versions." ::= { arpproxyFlush 1 } arpproxyFlushOps OBJECT-TYPE SYNTAX INTEGER MAX-ACCESS read-write STATUS current DESCRIPTION "Set the object to 1 to start flushing. This object is supported by R3.00 and later versions." ::= { arpproxyFlush 2 } arpproxyFlushEdgeRouterIp OBJECT-TYPE SYNTAX IpAddress MAX-ACCESS read-write STATUS current DESCRIPTION "Flush ARP table for the specified edge router. This object is supported by R3.00 and later versions." ::= { arpproxyFlush 3 } arpproxyFlushEdgeRouterVid OBJECT-TYPE SYNTAX VlanIndex MAX-ACCESS read-write STATUS current DESCRIPTION "Flush ARP table for the specified edge router. This object is supported by R3.00 and later versions." ::= { arpproxyFlush 4 } arpproxyFlushInterfaceIp OBJECT-TYPE SYNTAX IpAddress MAX-ACCESS read-write STATUS current DESCRIPTION "Flush ARP table for the specified interface. This object is supported by R3.00 and later versions." ::= { arpproxyFlush 5 } arpproxyFlushInterfaceMask OBJECT-TYPE SYNTAX INTEGER MAX-ACCESS read-write STATUS current DESCRIPTION "Flush ARP table for the specified interface. This object is supported by R3.00 and later versions." ::= { arpproxyFlush 6 } arpproxyFlushInterfaceVid OBJECT-TYPE SYNTAX VlanIndex MAX-ACCESS read-write STATUS current DESCRIPTION "Flush ARP table for the specified interface. This object is supported by R3.00 and later versions." ::= { arpproxyFlush 7 } -------------------- -- dtpvc -------------------- -- DT PVC Table dtpvcTable OBJECT-TYPE SYNTAX SEQUENCE OF DtpvcEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "This table includes Double Tagging (DT) PVC configuration." ::= { dtpvc 1 } dtpvcEntry OBJECT-TYPE SYNTAX DtpvcEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "An entry of dtpvcTable." INDEX { ifIndex, dtpvcVpi, dtpvcVci, dtpvcSvid } ::= { dtpvcTable 1 } DtpvcEntry ::= SEQUENCE { -- Common -- dtpvcVpi INTEGER, dtpvcVci INTEGER, dtpvcSvid VlanIndex, dtpvcSpriority INTEGER, dtpvcCvid VlanIndex, dtpvcCpriority INTEGER, dtpvcDSProfile DisplayString, dtpvcUSProfile DisplayString, dtpvcRowStatus RowStatus, -- Only for dtpvc -- dtpvcSuperChannel INTEGER, -- Only for paepvc -- dtpvcAcName DisplayString, dtpvcServiceName DisplayString, dtpvcHelloTime INTEGER } -- Common -- dtpvcVpi OBJECT-TYPE SYNTAX INTEGER (0..255) MAX-ACCESS read-only STATUS current DESCRIPTION "VPI of the pvc." ::= { dtpvcEntry 1 } dtpvcVci OBJECT-TYPE SYNTAX INTEGER (1..65535) MAX-ACCESS read-only STATUS current DESCRIPTION "VCI of the pvc." ::= { dtpvcEntry 2 } dtpvcSvid OBJECT-TYPE SYNTAX VlanIndex MAX-ACCESS read-only STATUS current DESCRIPTION "s-tag VLAN ID of the pvc." ::= { dtpvcEntry 3 } dtpvcSpriority OBJECT-TYPE SYNTAX INTEGER (0..7) MAX-ACCESS read-create STATUS current DESCRIPTION "s-tag priority of the pvc." ::= { dtpvcEntry 4 } dtpvcCvid OBJECT-TYPE SYNTAX VlanIndex MAX-ACCESS read-create STATUS current DESCRIPTION "c-tag VLAN ID of the pvc." ::= { dtpvcEntry 5 } dtpvcCpriority OBJECT-TYPE SYNTAX INTEGER (0..7) MAX-ACCESS read-create STATUS current DESCRIPTION "c-tag priority of the pvc." ::= { dtpvcEntry 6 } dtpvcDSProfile OBJECT-TYPE SYNTAX DisplayString (SIZE (1..31)) MAX-ACCESS read-create STATUS current DESCRIPTION "The value of this object identifies the row in the atmProfileTable, which applies for this dtpvc in DS side." ::= { dtpvcEntry 7 } dtpvcUSProfile OBJECT-TYPE SYNTAX DisplayString (SIZE (1..31)) MAX-ACCESS read-create STATUS current DESCRIPTION "The value of this object identifies the row in the atmProfileTable, which applies for this dtpvc in US side." ::= { dtpvcEntry 8 } dtpvcRowStatus OBJECT-TYPE SYNTAX RowStatus MAX-ACCESS read-create STATUS current DESCRIPTION "This object is used to create a new row or delete an existing row in this table." ::= { dtpvcEntry 9 } -- Only for DTPVC -- dtpvcSuperChannel OBJECT-TYPE SYNTAX INTEGER { enable(1), disable(2) } MAX-ACCESS read-create STATUS current DESCRIPTION "Specified the configured DTPVC is a super channel." ::= { dtpvcEntry 10 } -- Only for PAEPVC -- dtpvcAcName OBJECT-TYPE SYNTAX DisplayString MAX-ACCESS read-create STATUS current DESCRIPTION "Access concentrator name for paepvc." ::= { dtpvcEntry 11 } dtpvcServiceName OBJECT-TYPE SYNTAX DisplayString MAX-ACCESS read-create STATUS current DESCRIPTION "Service name for paepvc." ::= { dtpvcEntry 12 } dtpvcHelloTime OBJECT-TYPE SYNTAX INTEGER UNITS "second" MAX-ACCESS read-create STATUS current DESCRIPTION "The system will close the PVC if there are not any LCP echo messages passed through during the LCP hello time." ::= { dtpvcEntry 13 } -- DTPVC state -- dtpvcStateTable OBJECT-TYPE SYNTAX SEQUENCE OF DtpvcStateEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "This table show current DTPVC status." ::= { dtpvc 2 } dtpvcStateEntry OBJECT-TYPE SYNTAX DtpvcStateEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "An entry in dtpvcStateTable." INDEX { ifIndex, dtpvcStateVpi, dtpvcStateVci, dtpvcStateSvid } ::= { dtpvcStateTable 1 } DtpvcStateEntry ::= SEQUENCE { dtpvcStateVpi INTEGER, dtpvcStateVci INTEGER, dtpvcStateSvid VlanIndex, dtpvcStateSPriority INTEGER, dtpvcStateCvid VlanIndex, dtpvcStateCPriority INTEGER, --dtpvcStateMode DisplayString, dtpvcStateChannelType DisplayString, dtpvcStateEncap DisplayString } dtpvcStateVpi OBJECT-TYPE SYNTAX INTEGER (0..255) MAX-ACCESS read-only STATUS current DESCRIPTION "VPI of the dtpvc." ::= { dtpvcStateEntry 1 } dtpvcStateVci OBJECT-TYPE SYNTAX INTEGER (1..65535) MAX-ACCESS read-only STATUS current DESCRIPTION "VCI of the dtpvc." ::= { dtpvcStateEntry 2 } dtpvcStateSvid OBJECT-TYPE SYNTAX VlanIndex MAX-ACCESS read-only STATUS current DESCRIPTION "Default S-VID of the dtpvc." ::= { dtpvcStateEntry 3 } dtpvcStateSPriority OBJECT-TYPE SYNTAX INTEGER (0..7) MAX-ACCESS read-only STATUS current DESCRIPTION "S-priority of the dtpvc." ::= { dtpvcStateEntry 4 } dtpvcStateCvid OBJECT-TYPE SYNTAX VlanIndex MAX-ACCESS read-only STATUS current DESCRIPTION "Default C-VID of the dtpvc." ::= { dtpvcStateEntry 5 } dtpvcStateCPriority OBJECT-TYPE SYNTAX INTEGER (0..7) MAX-ACCESS read-only STATUS current DESCRIPTION "C-priority of the dtpvc." ::= { dtpvcStateEntry 6 } --dtpvcStateMode OBJECT-TYPE --SYNTAX DisplayString (SIZE (1..31)) --MAX-ACCESS read-only --STATUS current --DESCRIPTION --"The value of this object identifies the link mode at runntime." --::= { dtpvcStateEntry 7 } dtpvcStateChannelType OBJECT-TYPE SYNTAX DisplayString (SIZE (1..31)) MAX-ACCESS read-only STATUS current DESCRIPTION "The value of this object identifies the channel type at runtime." ::= { dtpvcStateEntry 8 } dtpvcStateEncap OBJECT-TYPE SYNTAX DisplayString (SIZE (1..31)) MAX-ACCESS read-only STATUS current DESCRIPTION "The value of this object identifies the channel encapsulation at runtime." ::= { dtpvcStateEntry 9 } -------------------- -- gbond -------------------- -- gbondTable gbondGroupTable OBJECT-TYPE SYNTAX SEQUENCE OF GbondGroupEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "A table containing the G.Bond configuration information for each bonding group of the device." ::= { gbond 1 } gbondGroupEntry OBJECT-TYPE SYNTAX GbondGroupEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "An entry of gbondTable." INDEX { gbondGroupName } ::= { gbondGroupTable 1 } GbondGroupEntry ::= SEQUENCE { gbondGroupName OCTET STRING, gbondGroupPorts OCTET STRING, -- gbondGroupSid INTEGER, gbondGroupUpRate Unsigned32, gbondGroupDownRate Unsigned32, gbondGroupRowStatus RowStatus } gbondGroupName OBJECT-TYPE SYNTAX OCTET STRING (SIZE (0..31)) MAX-ACCESS read-only STATUS current DESCRIPTION "An administratively assigned string, which may be used to identify bonding group." ::= { gbondGroupEntry 1 } gbondGroupPorts OBJECT-TYPE SYNTAX OCTET STRING MAX-ACCESS read-create STATUS current DESCRIPTION "The set of ports which are currently assigned to the bonding group of specified group name. Byte 1: Reserved(chassis) Byte 2~3: Reserved(slot) Byte 4: Reserved Byte 5~11:each octet specifies a set of eight ports, with the first octet specifying ports 1 through 8, etc." ::= { gbondGroupEntry 2 } -- gbondGroupSid OBJECT-TYPE -- SYNTAX INTEGER { -- sid8(1), -- sid12(2) -- } -- MAX-ACCESS read-create -- STATUS current -- DESCRIPTION -- "This object indicates the sequence index mode of the bonding group." -- ::= { gbondGroupEntry 3 } gbondGroupUpRate OBJECT-TYPE SYNTAX Unsigned32 MAX-ACCESS read-only STATUS current DESCRIPTION "The UP stream rate." ::= { gbondGroupEntry 4 } gbondGroupDownRate OBJECT-TYPE SYNTAX Unsigned32 MAX-ACCESS read-only STATUS current DESCRIPTION "The DOWN stream rate." ::= { gbondGroupEntry 5 } gbondGroupRowStatus OBJECT-TYPE SYNTAX RowStatus MAX-ACCESS read-create STATUS current DESCRIPTION "This object indicates the status of this entry." ::= { gbondGroupEntry 6 } -------------------- -- snrMgn -------------------- -- snrMgnTable snrMgnTable OBJECT-TYPE SYNTAX SEQUENCE OF SnrMarginEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "A table containing the per port SNR Margin configuration." ::= { snrMgn 1 } snrMgnEntry OBJECT-TYPE SYNTAX SnrMarginEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "An entry of snrMgnTable." INDEX { ifIndex } ::= { snrMgnTable 1 } SnrMarginEntry ::= SEQUENCE { snrMgnMode INTEGER, snrMgnUcTarget INTEGER, snrMgnUcMax INTEGER, snrMgnUcMin INTEGER, snrMgnUcDownshift INTEGER, snrMgnUcUpshift INTEGER, snrMgnUrTarget INTEGER, snrMgnUrMax INTEGER, snrMgnUrMin INTEGER, snrMgnUrDownshift INTEGER, snrMgnUrUpshift INTEGER } snrMgnMode OBJECT-TYPE SYNTAX INTEGER { profile(0), line(1) } MAX-ACCESS read-write STATUS current DESCRIPTION "Configure DSL SNR margin configuration mode of the specified ports. Profile: the SNR margin configuration comes from DSL profile. Line: the SNR margin configuration comes from line configuration." ::= { snrMgnEntry 1 } snrMgnUcTarget OBJECT-TYPE SYNTAX INTEGER (0..310) UNITS "tenth dB" MAX-ACCESS read-write STATUS current DESCRIPTION "Configured Target Signal/Noise Margin. This is the Noise Margin the modem must achieve with a BER of 10-7 or better to successfully complete initialization." ::= { snrMgnEntry 2 } snrMgnUcMax OBJECT-TYPE SYNTAX INTEGER (0..310) UNITS "tenth dB" MAX-ACCESS read-write STATUS current DESCRIPTION "Configured Maximum acceptable Signal/Noise Margin. If the Noise Margin is above this the modem should attempt to reduce its power output to optimize its operation." ::= { snrMgnEntry 3 } snrMgnUcMin OBJECT-TYPE SYNTAX INTEGER (0..310) UNITS "tenth dB" MAX-ACCESS read-write STATUS current DESCRIPTION "Configured Minimum acceptable Signal/Noise Margin. If the noise margin falls below this level, the modem should attempt to increase its power output. If that is not possible the modem will attempt to re-initialize or shut down." ::= { snrMgnEntry 4 } snrMgnUcDownshift OBJECT-TYPE SYNTAX INTEGER (0..310) UNITS "tenth dB" MAX-ACCESS read-write STATUS current DESCRIPTION "Configured Signal/Noise Margin for rate downshift. If the noise margin falls below this level, the modem should attempt to decrease its transmit rate. In the case that RADSL mode is not present, the value will be `0'." ::= { snrMgnEntry 5 } snrMgnUcUpshift OBJECT-TYPE SYNTAX INTEGER (0..310) UNITS "tenth dB" MAX-ACCESS read-write STATUS current DESCRIPTION "Configured Signal/Noise Margin for rate upshift. If the noise margin rises above this level, the modem should attempt to increase its transmit rate. In the case that RADSL is not present, the value will be `0'." ::= { snrMgnEntry 6 } snrMgnUrTarget OBJECT-TYPE SYNTAX INTEGER (0..310) UNITS "tenth dB" MAX-ACCESS read-write STATUS current DESCRIPTION "Configured Target Signal/Noise Margin. This is the Noise Margin the modem must achieve with a BER of 10-7 or better to successfully complete initialization." ::= { snrMgnEntry 7 } snrMgnUrMax OBJECT-TYPE SYNTAX INTEGER (0..310) UNITS "tenth dB" MAX-ACCESS read-write STATUS current DESCRIPTION "Configured Maximum acceptable Signal/Noise Margin. If the Noise Margin is above this the modem should attempt to reduce its power output to optimize its operation." ::= { snrMgnEntry 8 } snrMgnUrMin OBJECT-TYPE SYNTAX INTEGER (0..310) UNITS "tenth dB" MAX-ACCESS read-write STATUS current DESCRIPTION "Configured Minimum acceptable Signal/Noise Margin. If the noise margin falls below this level, the modem should attempt to increase its power output. If that is not possible the modem will attempt to re-initialize or shut down." ::= { snrMgnEntry 9 } snrMgnUrDownshift OBJECT-TYPE SYNTAX INTEGER (0..310) UNITS "tenth dB" MAX-ACCESS read-write STATUS current DESCRIPTION "Configured Signal/Noise Margin for rate downshift. If the noise margin falls below this level, the modem should attempt to decrease its transmit rate. In the case that RADSL mode is not present, the value will be `0'." ::= { snrMgnEntry 10 } snrMgnUrUpshift OBJECT-TYPE SYNTAX INTEGER (0..310) UNITS "tenth dB" MAX-ACCESS read-write STATUS current DESCRIPTION "Configured Signal/Noise Margin for rate upshift. If the noise margin rises above this level, the modem should attempt to increase its transmit rate. In the case that RADSL is not present, the value will be `0'." ::= { snrMgnEntry 11 } -------------------- -- dsl rate -------------------- -- dslRateTable dslRateTable OBJECT-TYPE SYNTAX SEQUENCE OF DslRateEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "A table containing the per port DSL Rate configuration." ::= { dslRate 1 } dslRateEntry OBJECT-TYPE SYNTAX DslRateEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "An entry of dslRateTable." INDEX { ifIndex } ::= { dslRateTable 1 } DslRateEntry ::= SEQUENCE { dslRateMode INTEGER, dslRateLatencyMode INTEGER, dslRateXtucMaxInterleaveDelay INTEGER, dslRateXtucMaxTxRate Unsigned32, dslRateXtucMinTxRate Unsigned32, dslRateXturMaxInterleaveDelay INTEGER, dslRateXturMaxTxRate Unsigned32, dslRateXturMinTxRate Unsigned32 } dslRateMode OBJECT-TYPE SYNTAX INTEGER { profile(0), line(1) } MAX-ACCESS read-write STATUS current DESCRIPTION "Configure DSL Rate configuration mode of the specified ports. Profile: the DSL Rate configuration comes from DSL profile. Line: the DSL Rate configuration comes from line configuration." ::= { dslRateEntry 1 } dslRateLatencyMode OBJECT-TYPE SYNTAX INTEGER { interleave(1), fast(2) } MAX-ACCESS read-only STATUS current DESCRIPTION "The latency mode is fast or interleave" ::= { dslRateEntry 2 } dslRateXtucMaxInterleaveDelay OBJECT-TYPE SYNTAX INTEGER (0..255) UNITS "milli-seconds" MAX-ACCESS read-write STATUS current DESCRIPTION "Configured maximum Interleave Delay for this channel. Interleave delay applies only to the interleave channel and defines the mapping (relative spacing) between subsequent input bytes at the interleaver input and their placement in the bit stream at the interleaver output. Larger numbers provide greater separation between consecutive input bytes in the output bit stream allowing for improved impulse noise immunity at the expense of payload latency." ::= { dslRateEntry 3 } dslRateXtucMaxTxRate OBJECT-TYPE SYNTAX Unsigned32 UNITS "kbps" MAX-ACCESS read-write STATUS current DESCRIPTION "Configured Maximum Transmit rate for `Fast' or `Interleave' channels, in bps." ::= { dslRateEntry 4 } dslRateXtucMinTxRate OBJECT-TYPE SYNTAX Unsigned32 UNITS "kbps" MAX-ACCESS read-write STATUS current DESCRIPTION "Configured Minimum Transmit rate for `Fast' or `Interleave' channels, in bps" ::= { dslRateEntry 5 } dslRateXturMaxInterleaveDelay OBJECT-TYPE SYNTAX INTEGER (0..255) UNITS "milli-seconds" MAX-ACCESS read-write STATUS current DESCRIPTION "Configured maximum Interleave Delay for this channel. Interleave delay applies only to the interleave channel and defines the mapping (relative spacing) between subsequent input bytes at the interleaver input and their placement in the bit stream at the interleaver output. Larger numbers provide greater separation between consecutive input bytes in the output bit stream allowing for improved impulse noise immunity at the expense of payload latency" ::= { dslRateEntry 6 } dslRateXturMaxTxRate OBJECT-TYPE SYNTAX Unsigned32 UNITS "kbps" MAX-ACCESS read-write STATUS current DESCRIPTION "Configured Target Signal/Noise Margin. This is the Noise Margin the modem must achieve with a BER of 10-7 or better to successfully complete initialization." ::= { dslRateEntry 7 } dslRateXturMinTxRate OBJECT-TYPE SYNTAX Unsigned32 UNITS "kbps" MAX-ACCESS read-write STATUS current DESCRIPTION "Configured Maximum Transmit rate for `Fast' or `Interleave' channels, in bps." ::= { dslRateEntry 8 } ---------------------------------------- -- switch ---------------------------------------- dscp OBJECT IDENTIFIER ::= { switch 10 } vlanIsolation OBJECT IDENTIFIER ::= { switch 12 } enetMtu OBJECT IDENTIFIER ::= { switch 13 } -- cfm OBJECT IDENTIFIER ::= { switch 14 } -- Standalone IP DSLAM puts all ACL features in 'switch', from OID 51 dhcp OBJECT IDENTIFIER ::= { switch 51 } macfilter OBJECT IDENTIFIER ::= { switch 53 } dhcpSnoop OBJECT IDENTIFIER ::= { switch 55 } acl OBJECT IDENTIFIER ::= { switch 56 } pppoeAgent OBJECT IDENTIFIER ::= { switch 57 } macff OBJECT IDENTIFIER ::= { switch 60 } -------------------- -- dscp -------------------- dscpMappingTable OBJECT-TYPE SYNTAX SEQUENCE OF DscpMappingEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "The table contains DSCP mapping configuration for the adsl and ethernet ports." ::= { dscp 1 } dscpMappingEntry OBJECT-TYPE SYNTAX DscpMappingEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "An entry of dscpMappingTable." INDEX { dscpSrcCodePoint } ::= { dscpMappingTable 1 } DscpMappingEntry ::= SEQUENCE { dscpSrcCodePoint INTEGER, -- dscpMapCodePoint INTEGER, dscpMapPriority INTEGER } dscpSrcCodePoint OBJECT-TYPE SYNTAX INTEGER MAX-ACCESS read-only STATUS current DESCRIPTION "The DSCP source code point used for mapping." ::= { dscpMappingEntry 1 } -- dscpMapCodePoint OBJECT-TYPE -- SYNTAX INTEGER (0..63) -- MAX-ACCESS read-write -- STATUS current -- DESCRIPTION -- "The mapping code point that will replace the source code point in the incoming packet." -- ::= { dscpMappingEntry 2 } dscpMapPriority OBJECT-TYPE SYNTAX INTEGER (0..7) MAX-ACCESS read-write STATUS current DESCRIPTION "The mapping p bits that will replace the source p bits in the incoming packet." ::= { dscpMappingEntry 3 } --- pfchen dscpPortTable OBJECT-TYPE SYNTAX SEQUENCE OF DscpPortEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "The table contains DSCP mapping configuration for the adsl and ethernet ports." ::= { dscp 2 } dscpPortEntry OBJECT-TYPE SYNTAX DscpPortEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "An entry of dscpPortTable." INDEX { ifIndex } ::= { dscpPortTable 1 } DscpPortEntry ::= SEQUENCE { dscpStatusEnable INTEGER } dscpStatusEnable OBJECT-TYPE SYNTAX INTEGER { enable(1), disable(2) } MAX-ACCESS read-write STATUS current DESCRIPTION "The DSCP port status." ::= { dscpPortEntry 1 } -------------------- -- Vlan Isolation -------------------- vlanIsolationTable OBJECT-TYPE SYNTAX SEQUENCE OF VlanIsolationEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "A table contains configuration of isolated VLAN." ::= { vlanIsolation 1 } vlanIsolationEntry OBJECT-TYPE SYNTAX VlanIsolationEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "An entry of vlanIsolationTable." INDEX { dot1qVlanIndex } ::= { vlanIsolationTable 1 } VlanIsolationEntry ::= SEQUENCE { vlanIsolationRowStatus INTEGER } vlanIsolationRowStatus OBJECT-TYPE SYNTAX RowStatus MAX-ACCESS read-create STATUS current DESCRIPTION "Row status of the table used to create/delete an entry." ::= { vlanIsolationEntry 1 } -------------------- -- enet MTU -------------------- enetMtuEntry OBJECT-TYPE SYNTAX INTEGER MAX-ACCESS read-write STATUS current DESCRIPTION "Sets the MTU size for layer 2 frame, size from 1526 to 1532, default value is 1526." ::= { enetMtu 1 } -------------------- -- CFM -------------------- -- cfmLoopbackPortTable -- cfmLoopbackPortTable OBJECT-TYPE -- SYNTAX SEQUENCE OF CfmLoopbackPortEntry -- MAX-ACCESS not-accessible -- STATUS current -- DESCRIPTION -- "A table that contains CFM information." -- ::= { cfm 1 } -- -- cfmLoopbackPortEntry OBJECT-TYPE -- SYNTAX CfmLoopbackPortEntry -- MAX-ACCESS not-accessible -- STATUS current -- DESCRIPTION -- "An entry in cfmLoopbackPortTable." -- INDEX { ifIndex } -- ::= { cfmLoopbackPortTable 1 } -- -- CfmLoopbackPortEntry ::= SEQUENCE { -- cfmLoopbackPortState INTEGER -- } -- -- cfmLoopbackPortState OBJECT-TYPE -- SYNTAX INTEGER { -- enable(1), -- disable(2) -- } -- MAX-ACCESS read-write -- STATUS current -- DESCRIPTION -- "CFM loopback enable/disable on the port." -- ::= { cfmLoopbackPortEntry 1 } -- -- cfmMIPTable -- -- cfmMIPTable OBJECT-TYPE -- SYNTAX SEQUENCE OF CfmMIPEntry -- MAX-ACCESS not-accessible -- STATUS current -- DESCRIPTION -- "" -- ::= { cfm 2 } -- -- cfmMIPEntry OBJECT-TYPE -- SYNTAX CfmMIPEntry -- MAX-ACCESS not-accessible -- STATUS current -- DESCRIPTION -- "An entry in cfmMIPTable." -- INDEX { cfmLevel, cfmVlanID, cfmPort } -- ::= { cfmMIPTable 1 } -- -- CfmMIPEntry ::= -- SEQUENCE { -- cfmLevel INTEGER, -- cfmVlanID INTEGER, -- cfmPort INTEGER, -- cfmMIPRowStatus RowStatus -- } -- -- cfmLevel OBJECT-TYPE -- SYNTAX INTEGER -- MAX-ACCESS not-accessible -- STATUS current -- DESCRIPTION -- "" -- ::= { cfmMIPEntry 1 } -- -- cfmVlanID OBJECT-TYPE -- SYNTAX INTEGER -- MAX-ACCESS not-accessible -- STATUS current -- DESCRIPTION -- "" -- ::= { cfmMIPEntry 2 } -- -- cfmPort OBJECT-TYPE -- SYNTAX INTEGER -- MAX-ACCESS not-accessible -- STATUS current -- DESCRIPTION -- "" -- ::= { cfmMIPEntry 3 } -- -- cfmMIPRowStatus OBJECT-TYPE -- SYNTAX RowStatus -- MAX-ACCESS read-create -- STATUS current -- DESCRIPTION -- "" -- ::= { cfmMIPEntry 4 } -- -- cfmActionEnableStatus OBJECT-TYPE -- SYNTAX INTEGER { -- enable(1), -- disable(2) -- } -- MAX-ACCESS read-write -- STATUS current -- DESCRIPTION -- "CFM Action enable status for the CO device" -- ::= { cfm 3 } -------------------- -- DHCP Relay -------------------- -- dhcpRelayEnable OBJECT-TYPE -- SYNTAX INTEGER { -- auto(1), -- both(2), -- disable(3) -- } -- MAX-ACCESS read-write -- STATUS current -- DESCRIPTION -- "Enable/disable DHCP relay Option82 function." -- ::= { dhcp 1 } dhcpRelay82Table OBJECT-TYPE SYNTAX SEQUENCE OF DhcpRelay82Entry MAX-ACCESS not-accessible STATUS current DESCRIPTION "A table that contains DHCP Relay configuration." ::= { dhcp 2 } dhcpRelay82Entry OBJECT-TYPE SYNTAX DhcpRelay82Entry MAX-ACCESS not-accessible STATUS current DESCRIPTION "The entry of DHCP Relay table." INDEX { dot1qVlanIndex } ::= { dhcpRelay82Table 1 } DhcpRelay82Entry ::= SEQUENCE { dhcpRelay82PrimaryServer IpAddress, dhcpRelay82SecondaryServer IpAddress, dhcpRelay82ActiveServer INTEGER, dhcpRelay82Enable INTEGER, dhcpRelay82Info DisplayString, dhcpRelay82RelayMode INTEGER, dhcpRelay82Suboption2Enable INTEGER, dhcpRelay82Suboption2Info DisplayString, dhcpRelay82EntryEnable INTEGER, dhcpRelay82EntryOptionMode INTEGER, dhcpRelay82VlanIp IpAddress, dhcpRelay82VlanMask INTEGER, dhcpRelay82VlanGateway IpAddress, dhcpRelay82ThirdServer IpAddress, dhcpRelay82FourthServer IpAddress, dhcpRelay82FifthServer IpAddress, dhcpRelay82ServerVid INTEGER } dhcpRelay82PrimaryServer OBJECT-TYPE SYNTAX IpAddress MAX-ACCESS read-write STATUS current DESCRIPTION "The IP address of the DHCP Relay primary server." ::= { dhcpRelay82Entry 1 } dhcpRelay82SecondaryServer OBJECT-TYPE SYNTAX IpAddress MAX-ACCESS read-write STATUS current DESCRIPTION "The IP address of the DHCP Relay secondary server." ::= { dhcpRelay82Entry 2 } dhcpRelay82ActiveServer OBJECT-TYPE SYNTAX INTEGER { primary(1), secondary(2), third(3), fourth(4), fifth(5) } MAX-ACCESS read-only STATUS current DESCRIPTION "The current active DHCP Relay server." ::= { dhcpRelay82Entry 3 } dhcpRelay82Enable OBJECT-TYPE SYNTAX INTEGER { enable(1), disable(2) } MAX-ACCESS read-create STATUS current DESCRIPTION "Enable/disable DHCP relay and Option82 function." ::= { dhcpRelay82Entry 4 } dhcpRelay82Info OBJECT-TYPE SYNTAX DisplayString (SIZE (0..23)) MAX-ACCESS read-create STATUS current DESCRIPTION "User specific Option82 information." ::= { dhcpRelay82Entry 5 } dhcpRelay82RelayMode OBJECT-TYPE SYNTAX INTEGER { auto(1), all(2) } MAX-ACCESS read-create STATUS current DESCRIPTION "DHCP relay mode." ::= { dhcpRelay82Entry 6 } dhcpRelay82Suboption2Enable OBJECT-TYPE SYNTAX INTEGER { enable(1), disable(2) } MAX-ACCESS read-create STATUS current DESCRIPTION "Enable/disable Option 82 sub-option 2." ::= { dhcpRelay82Entry 8 } dhcpRelay82Suboption2Info OBJECT-TYPE SYNTAX DisplayString MAX-ACCESS read-create STATUS current DESCRIPTION "User specified information for Option 82 sub-option 2." ::= { dhcpRelay82Entry 9 } dhcpRelay82EntryEnable OBJECT-TYPE SYNTAX INTEGER { auto(1), all(2), disable(3) } MAX-ACCESS read-create STATUS current DESCRIPTION "Enable/disable DHCP Relay" ::= { dhcpRelay82Entry 10 } dhcpRelay82EntryOptionMode OBJECT-TYPE SYNTAX INTEGER { private(1), tr101(2) } MAX-ACCESS read-create STATUS current DESCRIPTION "Option82 format." ::= { dhcpRelay82Entry 11 } dhcpRelay82VlanIp OBJECT-TYPE SYNTAX IpAddress MAX-ACCESS read-write STATUS current DESCRIPTION "The IP address of the DHCP Relay interface for this VLAN." ::= { dhcpRelay82Entry 12 } dhcpRelay82VlanMask OBJECT-TYPE SYNTAX INTEGER MAX-ACCESS read-write STATUS current DESCRIPTION "The network mask of the DHCP Relay interface for this VLAN." ::= { dhcpRelay82Entry 13 } dhcpRelay82VlanGateway OBJECT-TYPE SYNTAX IpAddress MAX-ACCESS read-write STATUS current DESCRIPTION "The gateway of the DHCP Relay interface for this VLAN." ::= { dhcpRelay82Entry 14 } dhcpRelay82ThirdServer OBJECT-TYPE SYNTAX IpAddress MAX-ACCESS read-write STATUS current DESCRIPTION "The IP address of the DHCP Relay third server." ::= { dhcpRelay82Entry 15 } dhcpRelay82FourthServer OBJECT-TYPE SYNTAX IpAddress MAX-ACCESS read-write STATUS current DESCRIPTION "The IP address of the DHCP Relay fourth server." ::= { dhcpRelay82Entry 16 } dhcpRelay82FifthServer OBJECT-TYPE SYNTAX IpAddress MAX-ACCESS read-write STATUS current DESCRIPTION "The IP address of the DHCP Relay fifth server." ::= { dhcpRelay82Entry 17 } dhcpRelay82ServerVid OBJECT-TYPE SYNTAX INTEGER MAX-ACCESS read-write STATUS current DESCRIPTION "The VID of the DHCP Relay server for this VLAN." ::= { dhcpRelay82Entry 18 } -- dhcpRelayOption82Sub1Info OBJECT-TYPE -- SYNTAX DisplayString (SIZE (0..23)) -- MAX-ACCESS read-write -- STATUS current -- DESCRIPTION -- "User specific Option82 subOption1 (Agent circuit ID) information." -- ::= { dhcp 3 } -- maxNumOfDhcpRelay82Conf OBJECT-TYPE -- SYNTAX INTEGER -- MAX-ACCESS read-only -- STATUS current -- DESCRIPTION -- "The maximum number of rows that can be created in dhcpRelay82Table." -- ::= { dhcp 4 } -- dhcpRelayOption82Sub1Enable OBJECT-TYPE -- SYNTAX INTEGER { -- enable(1), -- disable(2) -- } -- MAX-ACCESS read-write -- STATUS current -- DESCRIPTION -- "Enable/disable DHCP relay Option82 subOption1 (Agent Circuit ID) function." -- ::= { dhcp 5 } -- dhcpRelayOption82Sub2Info OBJECT-TYPE -- SYNTAX DisplayString (SIZE (0..23)) -- MAX-ACCESS read-write -- STATUS current -- DESCRIPTION -- "User specific Option82 subOption2 (Agent Remote ID) information." -- ::= { dhcp 6 } -- dhcpRelayOption82Sub2Enable OBJECT-TYPE -- SYNTAX INTEGER { -- enable(1), -- disable(2) -- } -- MAX-ACCESS read-write -- STATUS current -- DESCRIPTION -- "Enable/disable DHCP relay Option82 subOption2 (Agent Remote ID) function." -- ::= { dhcp 7 } -- dhcpRelayTest dhcpRelayTest OBJECT IDENTIFIER ::= { dhcp 8 } dhcpRelayTestVid OBJECT-TYPE SYNTAX INTEGER MAX-ACCESS read-write STATUS current DESCRIPTION "Setting the VID of the test server." ::= { dhcpRelayTest 1 } dhcpRelayTestIp OBJECT-TYPE SYNTAX IpAddress MAX-ACCESS read-write STATUS current DESCRIPTION "Setting the IP of the test server." ::= { dhcpRelayTest 2 } dhcpRelayTestOps OBJECT-TYPE SYNTAX INTEGER MAX-ACCESS read-write STATUS current DESCRIPTION "Set the object to 1 to test DHCP server." ::= { dhcpRelayTest 3 } dhcpRelayTestStatus OBJECT-TYPE SYNTAX DisplayString MAX-ACCESS read-only STATUS current DESCRIPTION "Display testing server status." ::= { dhcpRelayTest 4 } -- dhcpRelayArp dhcpRelayArp OBJECT IDENTIFIER ::= { dhcp 9 } dhcpRelayArpShowTable OBJECT-TYPE SYNTAX SEQUENCE OF DhcpRelayArpShowEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "The table displays DHCP ARP." ::= { dhcpRelayArp 1 } dhcpRelayArpShowEntry OBJECT-TYPE SYNTAX DhcpRelayArpShowEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "An entry of dhcpRelayArpShowTable." INDEX { dhcpRelayArpShowVid, dhcpRelayArpShowIp } ::= { dhcpRelayArpShowTable 1 } DhcpRelayArpShowEntry ::= SEQUENCE { dhcpRelayArpShowVid INTEGER, dhcpRelayArpShowIp IpAddress, dhcpRelayArpShowMac PhysAddress } dhcpRelayArpShowVid OBJECT-TYPE SYNTAX INTEGER MAX-ACCESS read-only STATUS current DESCRIPTION "Display the VID of the DHCP ARP entry." ::= { dhcpRelayArpShowEntry 1 } dhcpRelayArpShowIp OBJECT-TYPE SYNTAX IpAddress MAX-ACCESS read-only STATUS current DESCRIPTION "Display the IP of the DHCP ARP entry." ::= { dhcpRelayArpShowEntry 2 } dhcpRelayArpShowMac OBJECT-TYPE SYNTAX PhysAddress MAX-ACCESS read-only STATUS current DESCRIPTION "Display the MAC of the DHCP ARP entry." ::= { dhcpRelayArpShowEntry 3 } dhcpRelayArpFlushOps OBJECT-TYPE SYNTAX INTEGER MAX-ACCESS read-write STATUS current DESCRIPTION "Set the object to 1 to start flushing." ::= { dhcpRelayArp 2 } -------------------- -- MAC Filter -------------------- -- MAC Filter Port Table macFilterPortTable OBJECT-TYPE SYNTAX SEQUENCE OF MacFilterPortEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "This table includes the status of mac filtering for each port." ::= { macfilter 1 } macFilterPortEntry OBJECT-TYPE SYNTAX MacFilterPortEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "An entry in macFilterPortTable." INDEX { ifIndex } ::= { macFilterPortTable 1 } MacFilterPortEntry ::= SEQUENCE { macFilterPortEnable INTEGER, macFilterPortMacCount INTEGER, macFilterPortFilterMode INTEGER } macFilterPortEnable OBJECT-TYPE SYNTAX INTEGER { enableMacFilter(1), enableMacCount(2), -- enableOuiFilter(3), disable(4), enableMacFilterAndMacCount(5) } MAX-ACCESS read-write STATUS current DESCRIPTION "Enable/disable MAC filtering for the port." ::= { macFilterPortEntry 1 } macFilterPortMacCount OBJECT-TYPE SYNTAX INTEGER (1..128) MAX-ACCESS read-write STATUS current DESCRIPTION "The total number of MAC addresses allowed for the port." ::= { macFilterPortEntry 2 } macFilterPortFilterMode OBJECT-TYPE SYNTAX INTEGER { accept(1), deny(2) } MAX-ACCESS read-write STATUS current DESCRIPTION "The mac filter mode (accept or deny) for the port." ::= { macFilterPortEntry 3 } maxNumOfMacFiltersInSystem OBJECT-TYPE SYNTAX INTEGER MAX-ACCESS read-only STATUS current DESCRIPTION "The max number of mac filters supported in the system." ::= { macfilter 2 } maxNumOfMacFiltersPerPort OBJECT-TYPE SYNTAX INTEGER MAX-ACCESS read-only STATUS current DESCRIPTION "The max number of mac filters supported per port." ::= { macfilter 3 } currNumOfMacFiltersInSystem OBJECT-TYPE SYNTAX INTEGER MAX-ACCESS read-only STATUS current DESCRIPTION "The current number of mac filters in the system." ::= { macfilter 4 } -- MAC Table macFilterTable OBJECT-TYPE SYNTAX SEQUENCE OF MacFilterEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "A table that contains the mac filter addresses." ::= { macfilter 5 } macFilterEntry OBJECT-TYPE SYNTAX MacFilterEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "The entry of macFilterTable." INDEX { ifIndex, macFilterAddr } ::= { macFilterTable 1 } MacFilterEntry ::= SEQUENCE { macFilterAddr PhysAddress, macFilterRowStatus RowStatus } macFilterAddr OBJECT-TYPE SYNTAX PhysAddress MAX-ACCESS read-only STATUS current DESCRIPTION "The mac address which can pass through or be rejected from the port." ::= { macFilterEntry 1 } macFilterRowStatus OBJECT-TYPE SYNTAX RowStatus MAX-ACCESS read-create STATUS current DESCRIPTION "The row status of the entry." ::= { macFilterEntry 2 } -- Batch Set for MAC Filter macfilterBatchSet OBJECT IDENTIFIER ::= { macfilter 6 } macfilterTarget OBJECT-TYPE SYNTAX OCTET STRING MAX-ACCESS read-write STATUS current DESCRIPTION "This managed object is used for identify the target on which the port configuration should be performed. The target is encoded as: Byte 1: 0, Reserved(chassis) Byte 2~3: 0, Reserved(slot) Byte 4: 0, reserved Byte 5~11:each octet specifies a set of eight ports, with the first octet specifying ports 1 through 8, etc." ::= { macfilterBatchSet 1 } macfilterOps OBJECT-TYPE SYNTAX INTEGER MAX-ACCESS read-write STATUS current DESCRIPTION "The corresponding bit is set to 1 to start the operation. The various bit positions are: BIT 1: enable mac filter BIT 2: enable mac count filter BIT 3: disable mac filter BIT 4: set mac count BIT 5: disable mac count filter." ::= { macfilterBatchSet 2 } macFilterMacCountForBatchSet OBJECT-TYPE SYNTAX INTEGER (1..128) MAX-ACCESS read-write STATUS current DESCRIPTION "The total number of MAC addresses allowed for a port." ::= { macfilterBatchSet 3 } -- OUI Filter Table -- obsoleted since V3.0 at 2009/11/26 by maverick -- Not used for R3.x and above. ouiFilterTableOld OBJECT-TYPE SYNTAX SEQUENCE OF OuiFilterEntryOld MAX-ACCESS not-accessible STATUS current DESCRIPTION "A table that contains the OUI filter addresses." ::= { macfilter 7 } ouiFilterEntryOld OBJECT-TYPE SYNTAX OuiFilterEntryOld MAX-ACCESS not-accessible STATUS current DESCRIPTION "The entry of ouiFilterTableOld." INDEX { ifIndex, ouiFilterAddrOld } ::= { ouiFilterTableOld 1 } OuiFilterEntryOld ::= SEQUENCE { ouiFilterAddrOld OCTET STRING, ouiFilterRowStatusOld RowStatus } ouiFilterAddrOld OBJECT-TYPE SYNTAX OCTET STRING MAX-ACCESS read-only STATUS current DESCRIPTION "The first three bytes of the mac address which can pass through or be rejected from the port." ::= { ouiFilterEntryOld 1 } ouiFilterRowStatusOld OBJECT-TYPE SYNTAX RowStatus MAX-ACCESS read-create STATUS current DESCRIPTION "The row status of the entry." ::= { ouiFilterEntryOld 2 } maxNumOfOuiFiltersPerPort OBJECT-TYPE SYNTAX INTEGER MAX-ACCESS read-only STATUS current DESCRIPTION "The max number of OUI filters supported per port." ::= { macfilter 8 } ouiFilterPortTable OBJECT-TYPE SYNTAX SEQUENCE OF OuiFilterPortEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "This table includes the status of oui filtering for each port." ::= { macfilter 9 } ouiFilterPortEntry OBJECT-TYPE SYNTAX OuiFilterPortEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "An entry in macFilterPortTable." INDEX { ifIndex } ::= { ouiFilterPortTable 1 } OuiFilterPortEntry ::= SEQUENCE { ouiFilterPortEnable INTEGER, ouiFilterPortFilterMode INTEGER } ouiFilterPortEnable OBJECT-TYPE SYNTAX INTEGER { enableOuiFilter(1), disable(2) } MAX-ACCESS read-write STATUS current DESCRIPTION "Enable/disable oui filtering for the port." ::= { ouiFilterPortEntry 1 } ouiFilterPortFilterMode OBJECT-TYPE SYNTAX INTEGER { accept(1), deny(2) } MAX-ACCESS read-write STATUS current DESCRIPTION "The oui filter mode (accept or deny) for the port." ::= { ouiFilterPortEntry 2 } -- new OUI Filter VLAN maxNumOfOuiFiltersInSystem OBJECT-TYPE SYNTAX INTEGER MAX-ACCESS read-only STATUS current DESCRIPTION "The max number of OUI filters supported in system." ::= { macfilter 10 } maxNumOfOuiFiltersPerVlan OBJECT-TYPE SYNTAX INTEGER MAX-ACCESS read-only STATUS current DESCRIPTION "The max number of OUI filters supported per vlan." ::= { macfilter 11 } ouiFilterTable OBJECT-TYPE SYNTAX SEQUENCE OF OuiFilterEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "A table that contains the OUI filter addresses." ::= { macfilter 12 } ouiFilterEntry OBJECT-TYPE SYNTAX OuiFilterEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "The entry of ouiFilterTable." INDEX { dot1qVlanIndex, ouiFilterAddr } ::= { ouiFilterTable 1 } OuiFilterEntry ::= SEQUENCE { ouiFilterAddr OCTET STRING, ouiFilterRowStatus RowStatus } ouiFilterAddr OBJECT-TYPE SYNTAX OCTET STRING MAX-ACCESS read-only STATUS current DESCRIPTION "The first three bytes of the mac address which can pass through or be rejected from the vlan." ::= { ouiFilterEntry 1 } ouiFilterRowStatus OBJECT-TYPE SYNTAX RowStatus MAX-ACCESS read-create STATUS current DESCRIPTION "The row status of the entry." ::= { ouiFilterEntry 2 } ouiFilterVlanTable OBJECT-TYPE SYNTAX SEQUENCE OF OuiFilterVlanEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "This table includes the status of oui filtering for each configured VLAN." ::= { macfilter 13 } ouiFilterVlanEntry OBJECT-TYPE SYNTAX OuiFilterVlanEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "An entry in ouiFilterVlanTable." INDEX { dot1qVlanIndex } ::= { ouiFilterVlanTable 1 } OuiFilterVlanEntry ::= SEQUENCE { ouiFilterVlanEnable INTEGER, ouiFilterVlanFilterMode INTEGER } ouiFilterVlanEnable OBJECT-TYPE SYNTAX INTEGER { enableOuiFilter(1), disable(2) } MAX-ACCESS read-write STATUS current DESCRIPTION "Enable/disable oui filtering for the VLAN." ::= { ouiFilterVlanEntry 1 } ouiFilterVlanFilterMode OBJECT-TYPE SYNTAX INTEGER { accept(1), deny(2) } MAX-ACCESS read-write STATUS current DESCRIPTION "The oui filter mode (accept or deny) for the VLAN." ::= { ouiFilterVlanEntry 2 } -------------------- -- DHCP Snoop -------------------- -- dhcpSnoopPortTable dhcpSnoopPortTable OBJECT-TYPE SYNTAX SEQUENCE OF DhcpSnoopPortEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "This table includes DHCP snooping enable/disable for each port." ::= { dhcpSnoop 1 } dhcpSnoopPortEntry OBJECT-TYPE SYNTAX DhcpSnoopPortEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "An entry of dhcpSnoopPortTable." INDEX { ifIndex } ::= { dhcpSnoopPortTable 1 } DhcpSnoopPortEntry ::= SEQUENCE { dhcpSnoopEnable INTEGER, dhcpSnoopMaxcnt INTEGER, dhcpSnoopSmacverifyEnable INTEGER } dhcpSnoopEnable OBJECT-TYPE SYNTAX INTEGER { enable(1), disable(2) } MAX-ACCESS read-write STATUS current DESCRIPTION "Enable/disable DHCP snooping for a port." ::= { dhcpSnoopPortEntry 1 } dhcpSnoopMaxcnt OBJECT-TYPE SYNTAX INTEGER MAX-ACCESS read-write STATUS current DESCRIPTION "Set the max entries of the DHCP ARP table." ::= { dhcpSnoopPortEntry 2 } dhcpSnoopSmacverifyEnable OBJECT-TYPE SYNTAX INTEGER { enable(1), disable(2) } MAX-ACCESS read-write STATUS current DESCRIPTION "Enable/disable DHCP source MAC verify for a port." ::= { dhcpSnoopPortEntry 3 } -- dhcpSnoopOperation dhcpSnoopTarget OBJECT-TYPE SYNTAX OCTET STRING MAX-ACCESS read-write STATUS current DESCRIPTION "This managed object is used for identify the target on which the operation should be performed. The target is encoded as: Byte 1: the octet specifies a set of eight chassis, chassis 0 through 7 Byte 2~3: each octet specifies a set of eight slots, with the first octet specifying slots 1 through 8 and the second octet specifying slots 9 through 16. Byte 4: reserved Byte 5~11:each octet specifies a set of eight ports, with the first octet specifying ports 1 through 8, etc." ::= { dhcpSnoop 2 } dhcpSnoopOps OBJECT-TYPE SYNTAX INTEGER MAX-ACCESS read-write STATUS current DESCRIPTION "The corresponding bit is set to 1 to start the operation. The various bit positions are: BIT 1: DHCP snooping table flush." ::= { dhcpSnoop 3 } -- dhcpStaticTable dhcpStaticTable OBJECT-TYPE SYNTAX SEQUENCE OF DhcpStaticEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "This table defines DHCP static IP addresses." ::= { dhcpSnoop 4 } dhcpStaticEntry OBJECT-TYPE SYNTAX DhcpStaticEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "An entry of dhcpStaticTable." INDEX { ifIndex, dhcpStaticIpAddr } ::= { dhcpStaticTable 1 } DhcpStaticEntry ::= SEQUENCE { dhcpStaticIpAddr IpAddress, dhcpStaticRowStatus RowStatus } dhcpStaticIpAddr OBJECT-TYPE SYNTAX IpAddress MAX-ACCESS read-only STATUS current DESCRIPTION "The IP address which can pass through the port." ::= { dhcpStaticEntry 1 } dhcpStaticRowStatus OBJECT-TYPE SYNTAX RowStatus MAX-ACCESS read-create STATUS current DESCRIPTION "Row status of the table entry." ::= { dhcpStaticEntry 2 } maxNumOfDhcpStaticIp OBJECT-TYPE SYNTAX INTEGER MAX-ACCESS read-only STATUS current DESCRIPTION "The maximum number of DHCP static IP addresses which can be created for a port." ::= { dhcpSnoop 5 } dhcpSnoopMaxcntMode OBJECT-TYPE SYNTAX INTEGER { replace(1), drop(2) } MAX-ACCESS read-write STATUS current DESCRIPTION "When DHCP snooping table is full, new DHCP lease will replace first one in option 0 or will be dropped in option 1." ::= { dhcpSnoop 6 } -------------------- -- ACL Rule -------------------- -- aclSetTable aclSetTable OBJECT-TYPE SYNTAX SEQUENCE OF AclSetEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "aclsetTable." ::= { acl 1 } aclSetEntry OBJECT-TYPE SYNTAX AclSetEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "An entry of aclSetTable." INDEX { ifIndex, aclSetVpi, aclSetVci, aclSetProfileName } ::= { aclSetTable 1 } AclSetEntry ::= SEQUENCE { aclSetVpi INTEGER, aclSetVci INTEGER, aclSetProfileName DisplayString, aclSetRowStatus RowStatus } aclSetVpi OBJECT-TYPE SYNTAX INTEGER MAX-ACCESS read-only STATUS current DESCRIPTION "VPI value" ::= { aclSetEntry 1 } aclSetVci OBJECT-TYPE SYNTAX INTEGER MAX-ACCESS read-only STATUS current DESCRIPTION "VCI value" ::= { aclSetEntry 2 } aclSetProfileName OBJECT-TYPE SYNTAX DisplayString MAX-ACCESS read-only STATUS current DESCRIPTION "ACL Profile name" ::= { aclSetEntry 3 } aclSetRowStatus OBJECT-TYPE SYNTAX RowStatus MAX-ACCESS read-write STATUS current DESCRIPTION "RowStatus of aclSetEntry" ::= { aclSetEntry 4 } -- aclProfileTable aclProfileTable OBJECT-TYPE SYNTAX SEQUENCE OF AclProfileEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "aclProfileTable." ::= { acl 2 } aclProfileEntry OBJECT-TYPE SYNTAX AclProfileEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "An entry of aclProfileTable." INDEX { aclProfileRuleName } ::= { aclProfileTable 1 } AclProfileEntry ::= SEQUENCE { aclProfileRuleName DisplayString, aclProfileRuleNumber INTEGER, aclProfileActionNumber INTEGER, aclProfileRuleParamMask INTEGER, aclProfileRuleEtype INTEGER, aclProfileRuleVid INTEGER, aclProfileRuleSmac PhysAddress, aclProfileRuleDmac PhysAddress, aclProfileRulePriority INTEGER, aclProfileRuleProtocol INTEGER, aclProfileRuleSrcIP IpAddress, aclProfileRuleSrcIPMask INTEGER, aclProfileRuleDestIP IpAddress, aclProfileRuleDestIPMask INTEGER, aclProfileRuleStartTos INTEGER, aclProfileRuleEndTos INTEGER, aclProfileRuleSrcStartPort INTEGER, aclProfileRuleSrcEndPort INTEGER, aclProfileRuleDestStartPort INTEGER, aclProfileRuleDestEndPort INTEGER, aclProfileActionRate INTEGER, aclProfileActionrvlan INTEGER, aclProfileActionrpri INTEGER, aclProfileRowStatus RowStatus } aclProfileRuleName OBJECT-TYPE SYNTAX DisplayString MAX-ACCESS read-only STATUS current DESCRIPTION "Profile rule name" ::= { aclProfileEntry 1 } aclProfileRuleNumber OBJECT-TYPE SYNTAX INTEGER MAX-ACCESS read-write STATUS current DESCRIPTION "The managed object is for acl profile rule configuration. etype vlan (1), etype smac (2), etype dmac (3), vlan smac (4), vlan dmac (5), smac dmac (6), vlan priority (7), etype (8), vlan (9), smac (10), dmac (11), priority (12), protocol (13), {srcip /{|dstip /{|tos {|srcport {|dstport }}}}} (14) " ::= { aclProfileEntry 2 } aclProfileActionNumber OBJECT-TYPE SYNTAX INTEGER MAX-ACCESS read-write STATUS current DESCRIPTION "Profile action number. Bit 1: rate Bit 2: rvlan Bit 3: rpri Bit 4: deny Bit 1, Bit 2 & Bit 3 can multiple selection." ::= { aclProfileEntry 3 } aclProfileRuleParamMask OBJECT-TYPE SYNTAX INTEGER MAX-ACCESS read-write STATUS current DESCRIPTION "Profile rule parameter mask. BIT 1: srcip / BIT 2: dstip / BIT 3: tos BIT 4: srcport BIT 5: dstport " ::= { aclProfileEntry 4 } aclProfileRuleEtype OBJECT-TYPE SYNTAX INTEGER (0..65535) MAX-ACCESS read-write STATUS current DESCRIPTION "Profile rule etype" ::= { aclProfileEntry 5 } aclProfileRuleVid OBJECT-TYPE SYNTAX INTEGER (1..4094) MAX-ACCESS read-write STATUS current DESCRIPTION "Profile rule vid" ::= { aclProfileEntry 6 } aclProfileRuleSmac OBJECT-TYPE SYNTAX PhysAddress MAX-ACCESS read-write STATUS current DESCRIPTION "Profile rule source MAC" ::= { aclProfileEntry 7 } aclProfileRuleDmac OBJECT-TYPE SYNTAX PhysAddress MAX-ACCESS read-write STATUS current DESCRIPTION "Profile rule destination MAC" ::= { aclProfileEntry 8 } aclProfileRulePriority OBJECT-TYPE SYNTAX INTEGER (0..7) MAX-ACCESS read-write STATUS current DESCRIPTION "Profile rule priority" ::= { aclProfileEntry 9 } aclProfileRuleProtocol OBJECT-TYPE SYNTAX INTEGER (0..255) MAX-ACCESS read-write STATUS current DESCRIPTION "Profile rule protocol. icmp(1),igmp(2),ip(4),tcp(6), udp(17),gre(47),ospf(89), other ptype" ::= { aclProfileEntry 10 } aclProfileRuleSrcIP OBJECT-TYPE SYNTAX IpAddress MAX-ACCESS read-write STATUS current DESCRIPTION "Profile rule source IP" ::= { aclProfileEntry 11 } aclProfileRuleSrcIPMask OBJECT-TYPE SYNTAX INTEGER (0..32) MAX-ACCESS read-write STATUS current DESCRIPTION "The subnet mask of source IP mask" ::= { aclProfileEntry 12 } aclProfileRuleDestIP OBJECT-TYPE SYNTAX IpAddress MAX-ACCESS read-write STATUS current DESCRIPTION "Profile rule source IP" ::= { aclProfileEntry 13 } aclProfileRuleDestIPMask OBJECT-TYPE SYNTAX INTEGER (0..32) MAX-ACCESS read-write STATUS current DESCRIPTION "The subnet mask of dest IP mask" ::= { aclProfileEntry 14 } aclProfileRuleStartTos OBJECT-TYPE SYNTAX INTEGER (0..255) MAX-ACCESS read-write STATUS current DESCRIPTION "Profile rule start type of service" ::= { aclProfileEntry 15 } aclProfileRuleEndTos OBJECT-TYPE SYNTAX INTEGER (0..255) MAX-ACCESS read-write STATUS current DESCRIPTION "Profile rule end type of service" ::= { aclProfileEntry 16 } aclProfileRuleSrcStartPort OBJECT-TYPE SYNTAX INTEGER (0..65535) MAX-ACCESS read-write STATUS current DESCRIPTION "Profile rule source start port" ::= { aclProfileEntry 17 } aclProfileRuleSrcEndPort OBJECT-TYPE SYNTAX INTEGER (0..65535) MAX-ACCESS read-write STATUS current DESCRIPTION "Profile rule source end port" ::= { aclProfileEntry 18 } aclProfileRuleDestStartPort OBJECT-TYPE SYNTAX INTEGER (0..65535) MAX-ACCESS read-write STATUS current DESCRIPTION "Profile rule destination start port" ::= { aclProfileEntry 19 } aclProfileRuleDestEndPort OBJECT-TYPE SYNTAX INTEGER (0..65535) MAX-ACCESS read-write STATUS current DESCRIPTION "Profile rule destination end port" ::= { aclProfileEntry 20 } aclProfileActionRate OBJECT-TYPE SYNTAX INTEGER (1..65535) MAX-ACCESS read-write STATUS current DESCRIPTION "Profile action to replace to this rate" ::= { aclProfileEntry 21 } aclProfileActionrvlan OBJECT-TYPE SYNTAX INTEGER (1..4094) MAX-ACCESS read-write STATUS current DESCRIPTION "Profile action to replace to this vlan" ::= { aclProfileEntry 22 } aclProfileActionrpri OBJECT-TYPE SYNTAX INTEGER (0..7) MAX-ACCESS read-write STATUS current DESCRIPTION "Profile action to replace to this priority" ::= { aclProfileEntry 23 } aclProfileRowStatus OBJECT-TYPE SYNTAX RowStatus MAX-ACCESS read-write STATUS current DESCRIPTION "The row status of the entry." ::= { aclProfileEntry 24 } -------------------- -- PPPoE Agent -------------------- -- pppoeAgentTable pppoeAgentTable OBJECT-TYPE SYNTAX SEQUENCE OF PppoeAgentEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "A table that contains PPPoE DHCP Relay configuration." ::= { pppoeAgent 1 } pppoeAgentEntry OBJECT-TYPE SYNTAX PppoeAgentEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "An entry of pppoeAgentTable." INDEX { dot1qVlanIndex } ::= { pppoeAgentTable 1 } PppoeAgentEntry ::= SEQUENCE { pppoeAgentEnable INTEGER, pppoeAgentInfo DisplayString, pppoeAgentRowStatus RowStatus, pppoeAgentOptionMode INTEGER } pppoeAgentEnable OBJECT-TYPE SYNTAX INTEGER { enable(1), disable(2) } MAX-ACCESS read-create STATUS current DESCRIPTION "Enable/disable DHCP relay and Option82 function." ::= { pppoeAgentEntry 1 } pppoeAgentInfo OBJECT-TYPE SYNTAX DisplayString (SIZE (0..23)) MAX-ACCESS read-create STATUS current DESCRIPTION "User specific Option82 information." ::= { pppoeAgentEntry 2 } pppoeAgentRowStatus OBJECT-TYPE SYNTAX RowStatus MAX-ACCESS read-create STATUS current DESCRIPTION "Row status of the table entry." ::= { pppoeAgentEntry 3 } pppoeAgentOptionMode OBJECT-TYPE SYNTAX INTEGER { private(1), tr101(2) } MAX-ACCESS read-create STATUS current DESCRIPTION "Option82 format." ::= { pppoeAgentEntry 4 } maxNumOfPppoeDhcpRelay82Conf OBJECT-TYPE SYNTAX INTEGER MAX-ACCESS read-only STATUS current DESCRIPTION "The maximum number of rows that can be created in pppoeAgentTable." ::= { pppoeAgent 2 } ---------------------------------------- -- macff ---------------------------------------- macFfTable OBJECT-TYPE SYNTAX SEQUENCE OF MacFfEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "A table that contains MAC Force Forwarding configuration." ::= { macff 1 } macFfEntry OBJECT-TYPE SYNTAX MacFfEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "An entry of macFfTable." INDEX { macFfIndex } ::= { macFfTable 1 } MacFfEntry ::= SEQUENCE { macFfIndex INTEGER, macFfVid INTEGER, macFfArIP IpAddress, -- macFfArMask INTEGER, macFfSrcIP IpAddress, macFfSrcMask INTEGER, macFfRowStatus RowStatus } macFfIndex OBJECT-TYPE SYNTAX INTEGER MAX-ACCESS read-only STATUS current DESCRIPTION "Index of the MACFF." ::= { macFfEntry 1 } macFfVid OBJECT-TYPE SYNTAX INTEGER MAX-ACCESS read-write STATUS current DESCRIPTION "The VLAN-ID refering to this AR/AS." ::= { macFfEntry 2 } macFfArIP OBJECT-TYPE SYNTAX IpAddress MAX-ACCESS read-write STATUS current DESCRIPTION "IP of this AR/AS" ::= { macFfEntry 3 } macFfSrcIP OBJECT-TYPE SYNTAX IpAddress MAX-ACCESS read-write STATUS current DESCRIPTION "The source IP address of the MACFF." ::= { macFfEntry 4 } macFfSrcMask OBJECT-TYPE SYNTAX INTEGER MAX-ACCESS read-write STATUS current DESCRIPTION "The subnet mask of source IP mask." ::= { macFfEntry 5 } macFfRowStatus OBJECT-TYPE SYNTAX RowStatus MAX-ACCESS read-create STATUS current DESCRIPTION "The row status of the MacFfEntry entry." ::= { macFfEntry 6 } macFfArpFlush OBJECT-TYPE SYNTAX INTEGER MAX-ACCESS read-write STATUS current DESCRIPTION "Set the object to 1 to flush mac table." ::= { macff 3 } maxNumOfMacFfVlanInSystem OBJECT-TYPE SYNTAX INTEGER MAX-ACCESS read-only STATUS current DESCRIPTION "The max number of macff Vlans supported in the system." ::= { macff 4 } macFfVlanTable OBJECT-TYPE SYNTAX SEQUENCE OF MacFfVlanEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "A table that contains MAC Force Forwarding Vlan configuration." ::= { macff 5 } macFfVlanEntry OBJECT-TYPE SYNTAX MacFfVlanEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "An entry of macFfVlanTable." INDEX { dot1qVlanIndex } ::= { macFfVlanTable 1 } MacFfVlanEntry ::= SEQUENCE { macFfVlanRowstatus INTEGER, macFfVlanUnknownUnicast INTEGER } macFfVlanRowstatus OBJECT-TYPE SYNTAX RowStatus MAX-ACCESS read-create STATUS current DESCRIPTION "Row status of the table used to create/delete an entry." ::= { macFfVlanEntry 1 } macFfVlanUnknownUnicast OBJECT-TYPE SYNTAX INTEGER { flood(1), drop(2) } MAX-ACCESS read-create STATUS current DESCRIPTION "Setting downstream unknown uni-cast packet on macff vlan to flooding or dropping." ::= { macFfVlanEntry 2 } macFfStaticIPTable OBJECT-TYPE SYNTAX SEQUENCE OF MacFfStaticIPEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION " " ::= { macff 6 } macFfStaticIPEntry OBJECT-TYPE SYNTAX MacFfStaticIPEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "An entry of macFfTable." INDEX { macFfStaticIPPort, macFfStaticIPVid, macFfstaticIP , macFfStaticIPMask} ::= { macFfStaticIPTable 1 } MacFfStaticIPEntry ::= SEQUENCE { macFfStaticIPPort INTEGER, macFfStaticIPVid INTEGER, macFfstaticIP IpAddress, macFfStaticIPMask INTEGER, macFfStaticIPRowStatus RowStatus } macFfStaticIPPort OBJECT-TYPE SYNTAX INTEGER MAX-ACCESS read-only STATUS current DESCRIPTION " The port number, 1 ~ 48." ::= { macFfStaticIPEntry 1 } macFfStaticIPVid OBJECT-TYPE SYNTAX INTEGER MAX-ACCESS read-only STATUS current DESCRIPTION "VLAN ID of the IP range, 1 ~ 4094, the vid should be enable the MACFF function first." ::= { macFfStaticIPEntry 2 } macFfstaticIP OBJECT-TYPE SYNTAX IpAddress MAX-ACCESS read-only STATUS current DESCRIPTION "The specified IP range." ::= { macFfStaticIPEntry 3 } macFfStaticIPMask OBJECT-TYPE SYNTAX INTEGER MAX-ACCESS read-only STATUS current DESCRIPTION "Mask_bits is 24 .. 32." ::= { macFfStaticIPEntry 4 } macFfStaticIPRowStatus OBJECT-TYPE SYNTAX RowStatus MAX-ACCESS read-create STATUS current DESCRIPTION "The row status used to configure the table entry." ::= { macFfStaticIPEntry 5 } ---------------------------------------- -- sys ---------------------------------------- accessCtrl OBJECT IDENTIFIER ::= { sys 5 } extAlarm OBJECT IDENTIFIER ::= { sys 8 } user OBJECT IDENTIFIER ::= { sys 9 } usbCastCtrl OBJECT IDENTIFIER ::= { sys 10} dsbCastCtrl OBJECT IDENTIFIER ::= { sys 11} stdioTimeout OBJECT-TYPE SYNTAX INTEGER (0..300) MAX-ACCESS read-write STATUS current DESCRIPTION "Set the CLI/TELNET/WEB Session timeout, 0, or 1~300 minutes, 0 => disable." ::= { sys 12 } isConfigChanged OBJECT-TYPE SYNTAX INTEGER { yes(1), no(2) } MAX-ACCESS read-only STATUS current DESCRIPTION "If system configuration has been changed." ::= { sys 13 } fwUpgrade OBJECT IDENTIFIER ::= {sys 14} delayedReboot OBJECT IDENTIFIER ::= {sys 15} -------------------- -- Access Control -------------------- -- Secured Client Table securedClientTable OBJECT-TYPE SYNTAX SEQUENCE OF SecuredClientEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "A table that contains information about secured clients." ::= { accessCtrl 2 } securedClientEntry OBJECT-TYPE SYNTAX SecuredClientEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "A list of secured client entry." INDEX { securedClientIndex } ::= { securedClientTable 1 } SecuredClientEntry ::= SEQUENCE { securedClientIndex INTEGER, securedClientStartIp IpAddress, securedClientEndIp IpAddress, securedClientService INTEGER, securedClientEnable INTEGER } securedClientIndex OBJECT-TYPE SYNTAX INTEGER MAX-ACCESS read-only STATUS current DESCRIPTION "The index of the entry." ::= { securedClientEntry 1 } securedClientStartIp OBJECT-TYPE SYNTAX IpAddress MAX-ACCESS read-write STATUS current DESCRIPTION "The starting IP address of the secured client set." ::= { securedClientEntry 2 } securedClientEndIp OBJECT-TYPE SYNTAX IpAddress MAX-ACCESS read-write STATUS current DESCRIPTION "The ending IP address of the secured client set." ::= { securedClientEntry 3 } securedClientService OBJECT-TYPE SYNTAX INTEGER MAX-ACCESS read-write STATUS current DESCRIPTION "Each bit corresponds to a service. The bit is set to 1 if the service is enabled, and set to 0 if the service is disabled. The various bit positions are: BIT 1: telnet BIT 2: ftp BIT 3: web BIT 4: icmp BIT 5: not support BIT 6: snmp." ::= { securedClientEntry 4 } securedClientEnable OBJECT-TYPE SYNTAX INTEGER { enable(1), disable(2) } MAX-ACCESS read-write STATUS current DESCRIPTION "Enable/disable the entry." ::= { securedClientEntry 5 } -------------------- -- extAlarm -------------------- extAlarmTable OBJECT-TYPE SYNTAX SEQUENCE OF ExtAlarmEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "A table that contains external alarm information." ::= { extAlarm 1 } extAlarmEntry OBJECT-TYPE SYNTAX ExtAlarmEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "The entry of external alarm table." INDEX { extAlarmIndex } ::= { extAlarmTable 1 } ExtAlarmEntry ::= SEQUENCE { extAlarmIndex INTEGER, extAlarmname OCTET STRING, extAlarmstatus OCTET STRING, extAlarmTriggeredMode INTEGER } extAlarmIndex OBJECT-TYPE SYNTAX INTEGER MAX-ACCESS read-only STATUS current DESCRIPTION "The index of the entry." ::= { extAlarmEntry 1 } extAlarmname OBJECT-TYPE SYNTAX DisplayString (SIZE (1..31)) MAX-ACCESS read-write STATUS current DESCRIPTION "The external alarm name." ::= { extAlarmEntry 2 } extAlarmstatus OBJECT-TYPE SYNTAX DisplayString (SIZE (1..31)) MAX-ACCESS read-only STATUS current DESCRIPTION "Dispaly 'Normal' or 'Alarm' string" ::= { extAlarmEntry 3 } extAlarmTriggeredMode OBJECT-TYPE SYNTAX INTEGER { closeAlarm(1), openAlarm(2) } MAX-ACCESS read-write STATUS current DESCRIPTION "The external alarm triggered mode." ::= { extAlarmEntry 4 } -------------------- -- User Management -------------------- userAuthMode OBJECT-TYPE SYNTAX INTEGER { local(1), radius(2), localThenRadius(3) } MAX-ACCESS read-write STATUS current DESCRIPTION "User authentication procsssing mode." ::= { user 1 } userAuthServerIp OBJECT-TYPE SYNTAX IpAddress MAX-ACCESS read-write STATUS current DESCRIPTION "The IP address of the authentication server." ::= { user 2 } userAuthServerPort OBJECT-TYPE SYNTAX INTEGER MAX-ACCESS read-write STATUS current DESCRIPTION "The port of the authentication server." ::= { user 3 } userAuthServerSecret OBJECT-TYPE SYNTAX OCTET STRING MAX-ACCESS read-write STATUS current DESCRIPTION "The secret between the authentication server and the NE for authentication process." ::= { user 4 } -- userTable userTable OBJECT-TYPE SYNTAX SEQUENCE OF UserEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "A table that contains user information." ::= { user 5 } userEntry OBJECT-TYPE SYNTAX UserEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "An entry of userTable." INDEX { userName } ::= { userTable 1 } UserEntry ::= SEQUENCE { userName DisplayString, userPassword DisplayString, userPriviledge INTEGER, userRowStatus RowStatus } userName OBJECT-TYPE SYNTAX DisplayString MAX-ACCESS read-only STATUS current DESCRIPTION "The user name." ::= { userEntry 1 } userPassword OBJECT-TYPE SYNTAX DisplayString MAX-ACCESS read-create STATUS current DESCRIPTION "The user password." ::= { userEntry 2 } userPriviledge OBJECT-TYPE SYNTAX INTEGER { high(1), middle(2), low(3) } MAX-ACCESS read-create STATUS current DESCRIPTION "The user priviledge to decide what operation the user can and cannot do." ::= { userEntry 3 } userRowStatus OBJECT-TYPE SYNTAX RowStatus MAX-ACCESS read-create STATUS current DESCRIPTION "The row status used to create or delete a user." ::= { userEntry 4 } userAuthDefaultPriviledge OBJECT-TYPE SYNTAX INTEGER { high(1), middle(2), low(3), deny(4) } MAX-ACCESS read-write STATUS current DESCRIPTION "The user default priviledge to be assigned when radius authentication succeds but no user priviledge information(radius service-type) is provided." ::= { user 6 } -------------------- -- Upstream Broadcast -------------------- usBcastCtrlEnable OBJECT-TYPE SYNTAX INTEGER { enable(1), disable(2) } MAX-ACCESS read-write STATUS current DESCRIPTION "Enable/disable upstream broadcast control." ::= { usbCastCtrl 1 } usBcastCtrlRate OBJECT-TYPE SYNTAX INTEGER UNITS "Kbps" MAX-ACCESS read-write STATUS current DESCRIPTION "32~49984 in step of 32kbps" ::= { usbCastCtrl 2 } -------------------- -- Downstream Broadcast -------------------- dsBcastCtrlEnable OBJECT-TYPE SYNTAX INTEGER { enable(1), disable(2) } MAX-ACCESS read-write STATUS current DESCRIPTION "Enable/disable downstream broadcast control." ::= { dsbCastCtrl 1 } dsBcastCtrlRate OBJECT-TYPE SYNTAX INTEGER UNITS "Kbps" MAX-ACCESS read-write STATUS current DESCRIPTION "32~1000000 in step of 32 kbps" ::= { dsbCastCtrl 2 } -------------------- -- fwUpgrade -------------------- fwUpgradeVersion OBJECT-TYPE SYNTAX OCTET STRING MAX-ACCESS read-write STATUS current DESCRIPTION "Configure the target firmware version that will be upgraded." ::= { fwUpgrade 1 } fwUpgradeCheck OBJECT-TYPE SYNTAX INTEGER { enable(1), disable(2) } MAX-ACCESS read-write STATUS current DESCRIPTION "Enable/disable firmware upgrade version checking feature." ::= { fwUpgrade 2 } fwUpgradeStatus OBJECT-TYPE SYNTAX DisplayString MAX-ACCESS read-only STATUS current DESCRIPTION "Display current firmware upgrade status." ::= { fwUpgrade 3 } -------------------- -- delayedReboot -------------------- delayedRebootTimer OBJECT-TYPE SYNTAX INTEGER UNITS "sec" MAX-ACCESS read-write STATUS current DESCRIPTION "5~1800 secs, 0: reboot immediately." ::= { delayedReboot 1 } delayedRebootRemainingTime OBJECT-TYPE SYNTAX INTEGER UNITS "sec" MAX-ACCESS read-only STATUS current DESCRIPTION "Display the remaining time of scheduled reboot." ::= { delayedReboot 2 } delayedRebootCancel OBJECT-TYPE SYNTAX INTEGER { cancel(1) } MAX-ACCESS read-write STATUS current DESCRIPTION "cancel the scheduled reboot." ::= { delayedReboot 3 } ---------------------------------------- -- statistics ---------------------------------------- dhcpStats OBJECT IDENTIFIER ::= { statistics 11 } paepvcStats OBJECT IDENTIFIER ::= { statistics 12 } macStats OBJECT IDENTIFIER ::= { statistics 13 } ipbpvcStats OBJECT IDENTIFIER ::= { statistics 14 } -- obsoleted since R3.0 at 2009/11/26 by maverick macffStats OBJECT IDENTIFIER ::= { statistics 16 } enetStats OBJECT IDENTIFIER ::= { statistics 17 } adslStats OBJECT IDENTIFIER ::= { statistics 18 } -------------------- -- IGMP -------------------- igmpQueryCntTotal OBJECT-TYPE SYNTAX Counter32 MAX-ACCESS read-only STATUS current DESCRIPTION "The total number of IGMP query messages received." ::= { statistics 1 } igmpReportCntTotal OBJECT-TYPE SYNTAX Counter32 MAX-ACCESS read-only STATUS current DESCRIPTION "The total number of IGMP report messages received." ::= { statistics 2 } igmpLeaveCntTotal OBJECT-TYPE SYNTAX Counter32 MAX-ACCESS read-only STATUS current DESCRIPTION "The total number of IGMP leave messages received." ::= { statistics 3 } igmpNumOfActiveGroups OBJECT-TYPE SYNTAX INTEGER MAX-ACCESS read-only STATUS current DESCRIPTION "The total number of IGMP learned groups." ::= { statistics 4 } -- igmpGroupTable igmpGroupTable OBJECT-TYPE SYNTAX SEQUENCE OF IgmpGroupEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "This table includes igmp group information." ::= { statistics 5 } igmpGroupEntry OBJECT-TYPE SYNTAX IgmpGroupEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "An entry in igmpGroupTable." INDEX { igmpGroupIp } ::= { igmpGroupTable 1 } IgmpGroupEntry ::= SEQUENCE { igmpGroupIp IpAddress, igmpGroupvid INTEGER, igmpGroupnumberOfMembers INTEGER, igmpGroupMemberPorts PortList } igmpGroupIp OBJECT-TYPE SYNTAX IpAddress MAX-ACCESS read-only STATUS current DESCRIPTION "igmp group IP" ::= { igmpGroupEntry 1 } igmpGroupvid OBJECT-TYPE SYNTAX INTEGER MAX-ACCESS read-only STATUS current DESCRIPTION "vlan id" ::= { igmpGroupEntry 2 } igmpGroupnumberOfMembers OBJECT-TYPE SYNTAX INTEGER MAX-ACCESS read-only STATUS current DESCRIPTION "number Of Members" ::= { igmpGroupEntry 3 } igmpGroupMemberPorts OBJECT-TYPE SYNTAX PortList MAX-ACCESS read-only STATUS current DESCRIPTION "Group Member Ports" ::= { igmpGroupEntry 4 } -- igmpGroupPortTable igmpGroupPortTable OBJECT-TYPE SYNTAX SEQUENCE OF IgmpGroupPortEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "This table includes igmp Group port information." ::= { statistics 6 } igmpGroupPortEntry OBJECT-TYPE SYNTAX IgmpGroupPortEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "An entry in igmpGroupPortTable." INDEX { ifIndex , igmpGroupPortIp , igmpGroupPortvid} ::= { igmpGroupPortTable 1 } IgmpGroupPortEntry ::= SEQUENCE { igmpGroupPortIp IpAddress, igmpGroupPortvid INTEGER } igmpGroupPortIp OBJECT-TYPE SYNTAX IpAddress MAX-ACCESS read-only STATUS current DESCRIPTION "Igmp Group IP" ::= { igmpGroupPortEntry 1 } igmpGroupPortvid OBJECT-TYPE SYNTAX INTEGER MAX-ACCESS read-only STATUS current DESCRIPTION "Igmp Group vid" ::= { igmpGroupPortEntry 2 } -- igmpGroupV2Table igmpGroupV2Table OBJECT-TYPE SYNTAX SEQUENCE OF IgmpGroupV2Entry MAX-ACCESS not-accessible STATUS current DESCRIPTION "A table that displays IGMP learned group member information." ::= { statistics 7 } igmpGroupV2Entry OBJECT-TYPE SYNTAX IgmpGroupV2Entry MAX-ACCESS not-accessible STATUS current DESCRIPTION "An entry of igmpGroupV2Table." INDEX { igmpGroupV2Vid, igmpGroupV2Ip } ::= { igmpGroupV2Table 1 } IgmpGroupV2Entry ::= SEQUENCE { igmpGroupV2Vid VlanIndex, igmpGroupV2Ip IpAddress, igmpGroupV2NumOfMembers INTEGER, igmpGroupV2MemberPorts PortList } igmpGroupV2Vid OBJECT-TYPE SYNTAX VlanIndex MAX-ACCESS read-only STATUS current DESCRIPTION "The IGMP group VLAN ID." ::= { igmpGroupV2Entry 1 } igmpGroupV2Ip OBJECT-TYPE SYNTAX IpAddress MAX-ACCESS read-only STATUS current DESCRIPTION "The multicast IP address." ::= { igmpGroupV2Entry 2 } igmpGroupV2NumOfMembers OBJECT-TYPE SYNTAX INTEGER MAX-ACCESS read-only STATUS current DESCRIPTION "The number of member ports in the group." ::= { igmpGroupV2Entry 3 } igmpGroupV2MemberPorts OBJECT-TYPE SYNTAX PortList MAX-ACCESS read-only STATUS current DESCRIPTION "The member port list of the group." ::= { igmpGroupV2Entry 4 } -- igmpGroupPortV2Table igmpGroupPortV2Table OBJECT-TYPE SYNTAX SEQUENCE OF IgmpGroupPortV2Entry MAX-ACCESS not-accessible STATUS current DESCRIPTION "A table that displays IGMP joined groups in this port." ::= { statistics 8 } igmpGroupPortV2Entry OBJECT-TYPE SYNTAX IgmpGroupPortV2Entry MAX-ACCESS not-accessible STATUS current DESCRIPTION "An entry of igmpGroupPortV2Table." INDEX { ifIndex, igmpGroupPortV2Vid, igmpGroupPortV2Ip, igmpGroupPortV2SourceIp } ::= { igmpGroupPortV2Table 1 } IgmpGroupPortV2Entry ::= SEQUENCE { igmpGroupPortV2Vid VlanIndex, igmpGroupPortV2Ip IpAddress, igmpGroupPortV2SourceIp IpAddress } igmpGroupPortV2Vid OBJECT-TYPE SYNTAX VlanIndex MAX-ACCESS read-only STATUS current DESCRIPTION "The IGMP group VLAN ID." ::= { igmpGroupPortV2Entry 1 } igmpGroupPortV2Ip OBJECT-TYPE SYNTAX IpAddress MAX-ACCESS read-only STATUS current DESCRIPTION "The multicast IP address." ::= { igmpGroupPortV2Entry 2 } igmpGroupPortV2SourceIp OBJECT-TYPE SYNTAX IpAddress MAX-ACCESS read-only STATUS current DESCRIPTION "The source IP address that joins the IGMP group." ::= { igmpGroupPortV2Entry 3 } -- igmpPortCtrlPduTable igmpPortCtrlPduTable OBJECT-TYPE SYNTAX SEQUENCE OF IgmpPortCtrlPduEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "A table that displays IGMP related counter values in this port." ::= { statistics 9 } igmpPortCtrlPduEntry OBJECT-TYPE SYNTAX IgmpPortCtrlPduEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "An entry of igmpPortCtrlPduTable." INDEX { ifIndex } ::= { igmpPortCtrlPduTable 1 } IgmpPortCtrlPduEntry ::= SEQUENCE { igmpPortCtrlPduQueryCnt Counter32, igmpPortCtrlPduReportCnt Counter32, igmpPortCtrlPduLeaveCnt Counter32, igmpPortNumOfActiveGroups INTEGER, igmpPortCtrlAuditLeaveCnt Counter32 } igmpPortCtrlPduQueryCnt OBJECT-TYPE SYNTAX Counter32 MAX-ACCESS read-only STATUS current DESCRIPTION "The total number of IGMP query messages received in this port." ::= { igmpPortCtrlPduEntry 1 } igmpPortCtrlPduReportCnt OBJECT-TYPE SYNTAX Counter32 MAX-ACCESS read-only STATUS current DESCRIPTION "The total number of IGMP report messages received in this port." ::= { igmpPortCtrlPduEntry 2 } igmpPortCtrlPduLeaveCnt OBJECT-TYPE SYNTAX Counter32 MAX-ACCESS read-only STATUS current DESCRIPTION "The total number of IGMP leave messages received in this port." ::= { igmpPortCtrlPduEntry 3 } igmpPortNumOfActiveGroups OBJECT-TYPE SYNTAX INTEGER MAX-ACCESS read-only STATUS current DESCRIPTION "The total number of active IGMP groups in this port." ::= { igmpPortCtrlPduEntry 4 } igmpPortCtrlAuditLeaveCnt OBJECT-TYPE SYNTAX Counter32 MAX-ACCESS read-only STATUS current DESCRIPTION "The total number of groups left by audit query." ::= { igmpPortCtrlPduEntry 5 } -------------------- -- DHCP -------------------- -- dhcpSnoopIpTable dhcpSnoopIpTable OBJECT-TYPE SYNTAX SEQUENCE OF DhcpSnoopIpEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "This table shows the IP addresses and netmasks offered by the DHCP server." ::= { dhcpStats 1 } dhcpSnoopIpEntry OBJECT-TYPE SYNTAX DhcpSnoopIpEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "An entry of dhcpSnoopIpTable." INDEX { ifIndex, dhcpSnoopIp } ::= { dhcpSnoopIpTable 1 } DhcpSnoopIpEntry ::= SEQUENCE { dhcpSnoopIp IpAddress, dhcpSnoopMac PhysAddress, dhcpSnoopVid VlanIndex, dhcpSnoopMask INTEGER, dhcpSnoopGateway IpAddress, dhcpSnoopRouteMap OCTET STRING } dhcpSnoopIp OBJECT-TYPE SYNTAX IpAddress MAX-ACCESS read-only STATUS current DESCRIPTION "The snooped IP address." ::= { dhcpSnoopIpEntry 1 } dhcpSnoopMac OBJECT-TYPE SYNTAX PhysAddress MAX-ACCESS read-only STATUS current DESCRIPTION "The snooped MAC address." ::= { dhcpSnoopIpEntry 2 } dhcpSnoopVid OBJECT-TYPE SYNTAX VlanIndex MAX-ACCESS read-only STATUS current DESCRIPTION "The snooped VLAN ID." ::= { dhcpSnoopIpEntry 3 } dhcpSnoopMask OBJECT-TYPE SYNTAX INTEGER MAX-ACCESS read-only STATUS current DESCRIPTION "The snooped IP mask" ::= { dhcpSnoopIpEntry 4 } dhcpSnoopGateway OBJECT-TYPE SYNTAX IpAddress MAX-ACCESS read-only STATUS current DESCRIPTION "The snooped Gateway." ::= { dhcpSnoopIpEntry 5 } dhcpSnoopRouteMap OBJECT-TYPE SYNTAX OCTET STRING MAX-ACCESS read-only STATUS current DESCRIPTION "The refrence bit map of the dhcp route" ::= { dhcpSnoopIpEntry 6 } -- dhcpSnoopCounterTable dhcpSnoopCounterTable OBJECT-TYPE SYNTAX SEQUENCE OF DhcpSnoopCounterEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "This table shows the DHCP statistics." ::= { dhcpStats 2 } dhcpSnoopCounterEntry OBJECT-TYPE SYNTAX DhcpSnoopCounterEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "An entry of dhcpSnoopCounterTable." INDEX { ifIndex } ::= { dhcpSnoopCounterTable 1 } DhcpSnoopCounterEntry ::= SEQUENCE { dhcpDiscovery Counter64, dhcpOffer Counter64, dhcpRequest Counter64, dhcpAck Counter64, dhcpAckBySnoopFull Counter64 } dhcpDiscovery OBJECT-TYPE SYNTAX Counter64 MAX-ACCESS read-only STATUS current DESCRIPTION "The total number of received DHCP server discovery packets." ::= { dhcpSnoopCounterEntry 1 } dhcpOffer OBJECT-TYPE SYNTAX Counter64 MAX-ACCESS read-only STATUS current DESCRIPTION "The total number of received DHCP server offer packets." ::= { dhcpSnoopCounterEntry 2 } dhcpRequest OBJECT-TYPE SYNTAX Counter64 MAX-ACCESS read-only STATUS current DESCRIPTION "The total number of received DHCP IP request packets." ::= { dhcpSnoopCounterEntry 3 } dhcpAck OBJECT-TYPE SYNTAX Counter64 MAX-ACCESS read-only STATUS current DESCRIPTION "The total number of received DHCP IP acknowledge packets." ::= { dhcpSnoopCounterEntry 4 } dhcpAckBySnoopFull OBJECT-TYPE SYNTAX Counter64 MAX-ACCESS read-only STATUS current DESCRIPTION "The total number of received DHCP IP acknowledge packets that replace the oldest snooping entry in snooping table due to table full." ::= { dhcpSnoopCounterEntry 5 } dhcpRouteTable OBJECT-TYPE SYNTAX SEQUENCE OF DhcpRouteEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "A table that contains dhcp route information." ::= { dhcpStats 3 } dhcpRouteEntry OBJECT-TYPE SYNTAX DhcpRouteEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "An entry of dhcpRouteTable." INDEX { dhcpRouteIndex } ::= { dhcpRouteTable 1 } DhcpRouteEntry ::= SEQUENCE { dhcpRouteIndex INTEGER, dhcpRouteVid VlanIndex, dhcpRouteIP IpAddress, dhcpRouteMask INTEGER, dhcpRouteGwIP IpAddress } dhcpRouteIndex OBJECT-TYPE SYNTAX INTEGER (1..24) MAX-ACCESS read-only STATUS current DESCRIPTION "" ::= { dhcpRouteEntry 1 } dhcpRouteVid OBJECT-TYPE SYNTAX VlanIndex MAX-ACCESS read-only STATUS current DESCRIPTION "The VLAN-ID refering to this dhcp route." ::= { dhcpRouteEntry 2 } dhcpRouteIP OBJECT-TYPE SYNTAX IpAddress MAX-ACCESS read-only STATUS current DESCRIPTION "IP of this dhcp route" ::= { dhcpRouteEntry 3 } dhcpRouteMask OBJECT-TYPE SYNTAX INTEGER MAX-ACCESS read-only STATUS current DESCRIPTION "The subnet mask of source IP mask." ::= { dhcpRouteEntry 4 } dhcpRouteGwIP OBJECT-TYPE SYNTAX IpAddress MAX-ACCESS read-only STATUS current DESCRIPTION "The gateway IP address." ::= { dhcpRouteEntry 5 } -------------------- -- PAE PVC -------------------- -- paepvcSessionTable paepvcSessionTable OBJECT-TYPE SYNTAX SEQUENCE OF PaepvcSessionEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "This table shows the paepvc session statistics." ::= { paepvcStats 1 } paepvcSessionEntry OBJECT-TYPE SYNTAX PaepvcSessionEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "An entry of paepvcSessionTable." INDEX { ifIndex , paepvcSessionVpi, paepvcSessionVci } ::= { paepvcSessionTable 1 } PaepvcSessionEntry ::= SEQUENCE { paepvcSessionVpi INTEGER, paepvcSessionVci INTEGER, paepvcSessionState INTEGER, paepvcSessionId INTEGER, paepvcSessionUptime Unsigned32, paepvcSessionacname DisplayString, paepvcSessionsrvcname DisplayString } paepvcSessionVpi OBJECT-TYPE SYNTAX INTEGER MAX-ACCESS read-only STATUS current DESCRIPTION "The PAEPVC VPI." ::= { paepvcSessionEntry 1 } paepvcSessionVci OBJECT-TYPE SYNTAX INTEGER MAX-ACCESS read-only STATUS current DESCRIPTION "The PAEPVC VCI." ::= { paepvcSessionEntry 2 } paepvcSessionState OBJECT-TYPE SYNTAX INTEGER { down(1), pppoe(2), ppp(3), up(4) } MAX-ACCESS read-only STATUS current DESCRIPTION "The PAEPVC status." ::= { paepvcSessionEntry 3 } paepvcSessionId OBJECT-TYPE SYNTAX INTEGER MAX-ACCESS read-only STATUS current DESCRIPTION "The PAEPVC session ID." ::= { paepvcSessionEntry 4 } paepvcSessionUptime OBJECT-TYPE SYNTAX Unsigned32 UNITS "second" MAX-ACCESS read-only STATUS current DESCRIPTION "The PAEPVC session uptime." ::= { paepvcSessionEntry 5 } paepvcSessionacname OBJECT-TYPE SYNTAX DisplayString MAX-ACCESS read-only STATUS current DESCRIPTION "Access concentrator name." ::= { paepvcSessionEntry 6 } paepvcSessionsrvcname OBJECT-TYPE SYNTAX DisplayString MAX-ACCESS read-only STATUS current DESCRIPTION "Service name." ::= { paepvcSessionEntry 7 } -- paepvcCountTable paepvcCountTable OBJECT-TYPE SYNTAX SEQUENCE OF PaepvcCountEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "This table shows the paepvc counters." ::= { paepvcStats 2 } paepvcCountEntry OBJECT-TYPE SYNTAX PaepvcCountEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "An entry of paepvcCountTable." INDEX { ifIndex , paepvcCountVpi, paepvcCountVci } ::= { paepvcCountTable 1 } PaepvcCountEntry ::= SEQUENCE { paepvcCountVpi INTEGER, paepvcCountVci INTEGER, paepvcCountPppLcpCfgReqRx Unsigned32, paepvcCountPppLcpEchoReqRx Unsigned32, paepvcCountPppLcpEchoReplyRx Unsigned32, paepvcCountPadiTx Unsigned32, paepvcCountPadoRx Unsigned32, paepvcCountPadrTx Unsigned32, paepvcCountPadsRx Unsigned32, paepvcCountPadtTx Unsigned32, paepvcCountPadtRx Unsigned32, paepvcCountSrvcnameErrRx Unsigned32, paepvcCountAcSystemErrRx Unsigned32, paepvcCountGenericErrTx Unsigned32, paepvcCountGenericErrRx Unsigned32 } paepvcCountVpi OBJECT-TYPE SYNTAX INTEGER MAX-ACCESS read-only STATUS current DESCRIPTION "The PAEPVC VPI." ::= { paepvcCountEntry 1 } paepvcCountVci OBJECT-TYPE SYNTAX INTEGER MAX-ACCESS read-only STATUS current DESCRIPTION "The PAEPVC VCI." ::= { paepvcCountEntry 2 } paepvcCountPppLcpCfgReqRx OBJECT-TYPE SYNTAX Unsigned32 MAX-ACCESS read-only STATUS current DESCRIPTION "The number of ppp lcp config-request received." ::= { paepvcCountEntry 3 } paepvcCountPppLcpEchoReqRx OBJECT-TYPE SYNTAX Unsigned32 MAX-ACCESS read-only STATUS current DESCRIPTION "The number of ppp lcp echo-request received." ::= { paepvcCountEntry 4 } paepvcCountPppLcpEchoReplyRx OBJECT-TYPE SYNTAX Unsigned32 MAX-ACCESS read-only STATUS current DESCRIPTION "The number of ppp lcp echo-reply received." ::= { paepvcCountEntry 5 } paepvcCountPadiTx OBJECT-TYPE SYNTAX Unsigned32 MAX-ACCESS read-only STATUS current DESCRIPTION "The number of pppoe padi transfered" ::= { paepvcCountEntry 6 } paepvcCountPadoRx OBJECT-TYPE SYNTAX Unsigned32 MAX-ACCESS read-only STATUS current DESCRIPTION "The number of pppoe pado received" ::= { paepvcCountEntry 7 } paepvcCountPadrTx OBJECT-TYPE SYNTAX Unsigned32 MAX-ACCESS read-only STATUS current DESCRIPTION "The number of pppoe padr transfered" ::= { paepvcCountEntry 8 } paepvcCountPadsRx OBJECT-TYPE SYNTAX Unsigned32 MAX-ACCESS read-only STATUS current DESCRIPTION "The number of pppoe pads received" ::= { paepvcCountEntry 9 } paepvcCountPadtTx OBJECT-TYPE SYNTAX Unsigned32 MAX-ACCESS read-only STATUS current DESCRIPTION "The number of pppoe padt transfered" ::= { paepvcCountEntry 10 } paepvcCountPadtRx OBJECT-TYPE SYNTAX Unsigned32 MAX-ACCESS read-only STATUS current DESCRIPTION "The number of pppoe padt received" ::= { paepvcCountEntry 11 } paepvcCountSrvcnameErrRx OBJECT-TYPE SYNTAX Unsigned32 MAX-ACCESS read-only STATUS current DESCRIPTION "The number of pppoe service name error received" ::= { paepvcCountEntry 12 } paepvcCountAcSystemErrRx OBJECT-TYPE SYNTAX Unsigned32 MAX-ACCESS read-only STATUS current DESCRIPTION "The number of pppoe access concentrator name error received" ::= { paepvcCountEntry 13 } paepvcCountGenericErrTx OBJECT-TYPE SYNTAX Unsigned32 MAX-ACCESS read-only STATUS current DESCRIPTION "The number of pppoe generic error transfered" ::= { paepvcCountEntry 14 } paepvcCountGenericErrRx OBJECT-TYPE SYNTAX Unsigned32 MAX-ACCESS read-only STATUS current DESCRIPTION "The number of pppoe generic error received" ::= { paepvcCountEntry 15 } -------------------- -- MAC -------------------- macDisplayTarget OBJECT-TYPE SYNTAX INTEGER MAX-ACCESS read-write STATUS current DESCRIPTION "This managed object is a filter used for identify the target from which the MAC addresses are learned in macTable. The target could be: 99: all ports in the system 98: all subscriber ports 97: all Ethernet ports IfIndex is used for identifying subscriber ports and Ethernet Ports(e.g. 1 ~ 50)." ::= { macStats 1 } -- macTable macTable OBJECT-TYPE SYNTAX SEQUENCE OF MacEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "A table that contains information about unicast entries for which the bridge has forwarding and/or filtering information. This information is used by the transparent bridging function in determining how to propagate a received frame." ::= { macStats 2 } macEntry OBJECT-TYPE SYNTAX MacEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "An entry of macTable." INDEX { macAddress } ::= { macTable 1 } MacEntry ::= SEQUENCE { macAddress MacAddress, macPort INTEGER, macStatus INTEGER } macAddress OBJECT-TYPE SYNTAX MacAddress MAX-ACCESS read-only STATUS current DESCRIPTION "A unicast MAC address for which the bridge has forwarding and/or filtering information." ::= { macEntry 1 } macPort OBJECT-TYPE SYNTAX INTEGER MAX-ACCESS read-only STATUS current DESCRIPTION "The port from which the mac address has been learned." ::= { macEntry 2 } macStatus OBJECT-TYPE SYNTAX INTEGER { other(1), invalid(2), learned(3), self(4), mgmt(5) } MAX-ACCESS read-only STATUS current DESCRIPTION "The status of this entry." ::= { macEntry 3 } -------------------- -- ipbpvc -------------------- -- arpproxyTable arpproxyTable OBJECT-TYPE SYNTAX SEQUENCE OF ArpproxyEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "Display ARP table. This table is supported by R3.00 and later versions." ::= { ipbpvcStats 1 } arpproxyEntry OBJECT-TYPE SYNTAX ArpproxyEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "An entry of arpproxyTable." INDEX { ipbpvcDomainName, arpproxyIp } ::= { arpproxyTable 1 } ArpproxyEntry ::= SEQUENCE { arpproxyIp IpAddress, arpproxyMac MacAddress, arpproxyIfIndex INTEGER, arpproxyVpi INTEGER, arpproxyVci INTEGER, arpproxyInterfaceIp IpAddress, arpproxyInterfaceMask INTEGER, arpproxyInterfaceVid VlanIndex, arpproxyDhcpIp INTEGER, arpproxyType INTEGER } arpproxyIp OBJECT-TYPE SYNTAX IpAddress MAX-ACCESS read-only STATUS current DESCRIPTION "" ::= { arpproxyEntry 1 } arpproxyMac OBJECT-TYPE SYNTAX MacAddress MAX-ACCESS read-only STATUS current DESCRIPTION "" ::= { arpproxyEntry 2 } arpproxyIfIndex OBJECT-TYPE SYNTAX INTEGER MAX-ACCESS read-only STATUS current DESCRIPTION "" ::= { arpproxyEntry 3 } arpproxyVpi OBJECT-TYPE SYNTAX INTEGER MAX-ACCESS read-only STATUS current DESCRIPTION "" ::= { arpproxyEntry 4 } arpproxyVci OBJECT-TYPE SYNTAX INTEGER MAX-ACCESS read-only STATUS current DESCRIPTION "" ::= { arpproxyEntry 5 } arpproxyInterfaceIp OBJECT-TYPE SYNTAX IpAddress MAX-ACCESS read-only STATUS current DESCRIPTION "" ::= { arpproxyEntry 6 } arpproxyInterfaceMask OBJECT-TYPE SYNTAX INTEGER MAX-ACCESS read-only STATUS current DESCRIPTION "" ::= { arpproxyEntry 7 } arpproxyInterfaceVid OBJECT-TYPE SYNTAX VlanIndex MAX-ACCESS read-only STATUS current DESCRIPTION "" ::= { arpproxyEntry 8 } arpproxyDhcpIp OBJECT-TYPE SYNTAX INTEGER { true(1), false(2) } MAX-ACCESS read-only STATUS current DESCRIPTION "" ::= { arpproxyEntry 9 } arpproxyType OBJECT-TYPE SYNTAX INTEGER { upstream(1), downstream(2) } MAX-ACCESS read-only STATUS current DESCRIPTION "" ::= { arpproxyEntry 10 } -- ipbpvcIfDynamicTable ipbpvcIfDynamicTable OBJECT-TYPE SYNTAX SEQUENCE OF IpbpvcIfDynamicEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "Display runtime interfaces. This table is supported by R3.00 and later versions." ::= { ipbpvcStats 2 } ipbpvcIfDynamicEntry OBJECT-TYPE SYNTAX IpbpvcIfDynamicEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "An entry of ipbpvcIfDynamicTable." INDEX { ipbpvcDomainName, ipbpvcIfDynamicIp, ipbpvcIfDynamicMask, ipbpvcDomainVlanId } ::= { ipbpvcIfDynamicTable 1 } IpbpvcIfDynamicEntry ::= SEQUENCE { ipbpvcIfDynamicIp IpAddress, ipbpvcIfDynamicMask INTEGER, ipbpvcIfDynamicIfIndex INTEGER, ipbpvcIfDynamicVpi INTEGER, ipbpvcIfDynamicVci INTEGER } ipbpvcIfDynamicIp OBJECT-TYPE SYNTAX IpAddress MAX-ACCESS read-only STATUS current DESCRIPTION "" ::= { ipbpvcIfDynamicEntry 1 } ipbpvcIfDynamicMask OBJECT-TYPE SYNTAX INTEGER MAX-ACCESS read-only STATUS current DESCRIPTION "" ::= { ipbpvcIfDynamicEntry 2 } ipbpvcIfDynamicIfIndex OBJECT-TYPE SYNTAX INTEGER MAX-ACCESS read-only STATUS current DESCRIPTION "" ::= { ipbpvcIfDynamicEntry 3 } ipbpvcIfDynamicVpi OBJECT-TYPE SYNTAX INTEGER MAX-ACCESS read-only STATUS current DESCRIPTION "" ::= { ipbpvcIfDynamicEntry 4 } ipbpvcIfDynamicVci OBJECT-TYPE SYNTAX INTEGER MAX-ACCESS read-only STATUS current DESCRIPTION "" ::= { ipbpvcIfDynamicEntry 5 } -- ipbpvcRouteDynamicTable ipbpvcRouteDynamicTable OBJECT-TYPE SYNTAX SEQUENCE OF IpbpvcRouteDynamicEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "Display runtime routing table. This table is supported by R3.00 and later versions." ::= { ipbpvcStats 3 } ipbpvcRouteDynamicEntry OBJECT-TYPE SYNTAX IpbpvcRouteDynamicEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "An entry of ipbpvcRouteDynamicTable." INDEX { ipbpvcDomainName, ipbpvcRouteDynamicType, ipbpvcRouteDynamicIp, ipbpvcRouteDynamicMask } ::= { ipbpvcRouteDynamicTable 1 } IpbpvcRouteDynamicEntry ::= SEQUENCE { ipbpvcRouteDynamicType INTEGER, ipbpvcRouteDynamicIp IpAddress, ipbpvcRouteDynamicMask INTEGER, ipbpvcRouteDynamicNextHop IpAddress, ipbpvcRouteDynamicMetric INTEGER, ipbpvcRouteDynamicPriority INTEGER } ipbpvcRouteDynamicType OBJECT-TYPE SYNTAX INTEGER { upstream(1), downstream(2) } MAX-ACCESS read-only STATUS current DESCRIPTION "" ::= { ipbpvcRouteDynamicEntry 1 } ipbpvcRouteDynamicIp OBJECT-TYPE SYNTAX IpAddress MAX-ACCESS read-only STATUS current DESCRIPTION "" ::= { ipbpvcRouteDynamicEntry 2 } ipbpvcRouteDynamicMask OBJECT-TYPE SYNTAX INTEGER MAX-ACCESS read-only STATUS current DESCRIPTION "" ::= { ipbpvcRouteDynamicEntry 3 } ipbpvcRouteDynamicNextHop OBJECT-TYPE SYNTAX IpAddress MAX-ACCESS read-only STATUS current DESCRIPTION "" ::= { ipbpvcRouteDynamicEntry 4 } ipbpvcRouteDynamicMetric OBJECT-TYPE SYNTAX INTEGER MAX-ACCESS read-only STATUS current DESCRIPTION "" ::= { ipbpvcRouteDynamicEntry 5 } ipbpvcRouteDynamicPriority OBJECT-TYPE SYNTAX INTEGER MAX-ACCESS read-only STATUS current DESCRIPTION "" ::= { ipbpvcRouteDynamicEntry 6 } ------------------------------ -- enetStats ------------------------------ enetSfpInfoTable OBJECT-TYPE SYNTAX SEQUENCE OF EnetSfpInfoEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "This table includes sfp info of enet port." ::= { enetStats 2 } enetSfpInfoEntry OBJECT-TYPE SYNTAX EnetSfpInfoEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "An entry in enetSfpInfoTable." INDEX {ifIndex} ::= { enetSfpInfoTable 1 } EnetSfpInfoEntry ::= SEQUENCE { enetSfpInfoTxpower INTEGER, enetSfpInfoRxpower INTEGER, enetSfpInfoTemperature INTEGER, enetSfpInfoTxBias INTEGER, enetSfpInfoVoltage INTEGER } enetSfpInfoTxpower OBJECT-TYPE SYNTAX INTEGER (1..65535) UNITS "10^-4 mW" MAX-ACCESS read-only STATUS current DESCRIPTION "Measured Tx Output Power." ::= { enetSfpInfoEntry 1 } enetSfpInfoRxpower OBJECT-TYPE SYNTAX INTEGER (1..65535) UNITS "10^-4 C" MAX-ACCESS read-only STATUS current DESCRIPTION "Measured Rx Output Power." ::= { enetSfpInfoEntry 2 } enetSfpInfoTemperature OBJECT-TYPE SYNTAX INTEGER (-1280000..1280000) UNITS "10^-4 C" MAX-ACCESS read-only STATUS current DESCRIPTION "Measured temperature." ::= { enetSfpInfoEntry 3 } enetSfpInfoTxBias OBJECT-TYPE SYNTAX INTEGER (0..131000) UNITS "10^-3 mA" MAX-ACCESS read-only STATUS current DESCRIPTION "Measured tx bias." ::= { enetSfpInfoEntry 4 } enetSfpInfoVoltage OBJECT-TYPE SYNTAX INTEGER (0..65000) UNITS "0.1mV" MAX-ACCESS read-only STATUS current DESCRIPTION "Measured voltage." ::= { enetSfpInfoEntry 5 } ------------------------------ -- adslStats ------------------------------ adslPortUtilTable OBJECT-TYPE SYNTAX SEQUENCE OF AdslPortUtilEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "This table includes adsl port utilization." ::= { adslStats 1 } adslPortUtilEntry OBJECT-TYPE SYNTAX AdslPortUtilEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "An entry in adslPortUtilEntry." INDEX {ifIndex} ::= { adslPortUtilTable 1 } AdslPortUtilEntry ::= SEQUENCE { adslPortUtilTx INTEGER, adslPortUtilRx INTEGER } adslPortUtilTx OBJECT-TYPE SYNTAX INTEGER (0..100) MAX-ACCESS read-only STATUS current DESCRIPTION "Measure adsl port's tx utilization." ::= { adslPortUtilEntry 1 } adslPortUtilRx OBJECT-TYPE SYNTAX INTEGER (0..100) MAX-ACCESS read-only STATUS current DESCRIPTION "Measure adsl port's rx utilization." ::= { adslPortUtilEntry 2 } ---------------------------------------- -- macFfStats ---------------------------------------- macFfStatsTable OBJECT-TYPE SYNTAX SEQUENCE OF MacFfStatsEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "A table that contains MAC Force Forwarding static configuration and dynamic information." ::= { macffStats 1 } macFfStatsEntry OBJECT-TYPE SYNTAX MacFfStatsEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "An entry of macFfStatsTable." INDEX { macFfStatsIndex } ::= { macFfStatsTable 1 } MacFfStatsEntry ::= SEQUENCE { macFfStatsIndex INTEGER, macFfStatsVid VlanIndex, macFfStatsArIP IpAddress, macFfStatsSrcIP IpAddress, macFfStatsSrcMask INTEGER } macFfStatsIndex OBJECT-TYPE SYNTAX INTEGER MAX-ACCESS read-only STATUS current DESCRIPTION "Index of the MACFF." ::= { macFfStatsEntry 1 } macFfStatsVid OBJECT-TYPE SYNTAX VlanIndex MAX-ACCESS read-only STATUS current DESCRIPTION "The VLAN-ID refering to this AR/AS." ::= { macFfStatsEntry 2 } macFfStatsArIP OBJECT-TYPE SYNTAX IpAddress MAX-ACCESS read-only STATUS current DESCRIPTION "IP of this AR/AS" ::= { macFfStatsEntry 3 } macFfStatsSrcIP OBJECT-TYPE SYNTAX IpAddress MAX-ACCESS read-only STATUS current DESCRIPTION "The source IP address of the MACFF." ::= { macFfStatsEntry 4 } macFfStatsSrcMask OBJECT-TYPE SYNTAX INTEGER MAX-ACCESS read-only STATUS current DESCRIPTION "The subnet mask of source IP mask." ::= { macFfStatsEntry 5 } macFfArpTable OBJECT-TYPE SYNTAX SEQUENCE OF MacFfArpEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "A table that contains MAC Force Forwarding ARP information." ::= { macffStats 2 } macFfArpEntry OBJECT-TYPE SYNTAX MacFfArpEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "An entry of macFfArpTable." INDEX { macFfArpVid, macFfArpIP} ::= { macFfArpTable 1 } MacFfArpEntry ::= SEQUENCE { macFfArpVid VlanIndex, macFfArpIP IpAddress, macFfArpPort INTEGER, macFfArpMac PhysAddress } macFfArpVid OBJECT-TYPE SYNTAX VlanIndex MAX-ACCESS read-only STATUS current DESCRIPTION "The VLAN-ID refering to this AR/AS." ::= { macFfArpEntry 1 } macFfArpIP OBJECT-TYPE SYNTAX IpAddress MAX-ACCESS read-only STATUS current DESCRIPTION "IP of this AR/AS." ::= { macFfArpEntry 2 } macFfArpPort OBJECT-TYPE SYNTAX INTEGER MAX-ACCESS read-only STATUS current DESCRIPTION "Port of this AR/AS." ::= { macFfArpEntry 3 } macFfArpMac OBJECT-TYPE SYNTAX PhysAddress MAX-ACCESS read-only STATUS current DESCRIPTION "MAC address of the AR or AS." ::= { macFfArpEntry 4 } macFfArpCounterTable OBJECT-TYPE SYNTAX SEQUENCE OF MacFfArpCounterEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "A table that contains MAC Force Forwarding ARP counter information." ::= { macffStats 3 } macFfArpCounterEntry OBJECT-TYPE SYNTAX MacFfArpCounterEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "An entry of macFfArpCounterTable." INDEX { ifIndex } ::= { macFfArpCounterTable 1 } MacFfArpCounterEntry ::= SEQUENCE { macFfArpCounterRequestTX Counter32, macFfArpCounterRequestRX Counter32, macFfArpCounterRequestRXDrop Counter32, macFfArpCounterReplyTX Counter32, macFfArpCounterReplyRX Counter32, macFfArpCounterReplyRXDrop Counter32 } macFfArpCounterRequestTX OBJECT-TYPE SYNTAX Counter32 MAX-ACCESS read-only STATUS current DESCRIPTION "ARP Request TX counter." ::= { macFfArpCounterEntry 1 } macFfArpCounterRequestRX OBJECT-TYPE SYNTAX Counter32 MAX-ACCESS read-only STATUS current DESCRIPTION "ARP Request RX counter." ::= { macFfArpCounterEntry 2 } macFfArpCounterRequestRXDrop OBJECT-TYPE SYNTAX Counter32 MAX-ACCESS read-only STATUS current DESCRIPTION "ARP Request RX drop counter." ::= { macFfArpCounterEntry 3 } macFfArpCounterReplyTX OBJECT-TYPE SYNTAX Counter32 MAX-ACCESS read-only STATUS current DESCRIPTION "ARP Reply TX counter." ::= { macFfArpCounterEntry 4 } macFfArpCounterReplyRX OBJECT-TYPE SYNTAX Counter32 MAX-ACCESS read-only STATUS current DESCRIPTION "ARP Reply RX counter." ::= { macFfArpCounterEntry 5 } macFfArpCounterReplyRXDrop OBJECT-TYPE SYNTAX Counter32 MAX-ACCESS read-only STATUS current DESCRIPTION "ARP Reply RX drop counter." ::= { macFfArpCounterEntry 6 } ---------------------------------------- -- clear ---------------------------------------- counterClearTarget OBJECT-TYPE SYNTAX OCTET STRING MAX-ACCESS read-write STATUS current DESCRIPTION "This managed object is used for identify the target on which the counter would be cleared. The target is encoded as: Byte 1: reserved Byte 2~3: reserved Byte 4: reserved Byte 5~11:each octet specifies a set of eight ports, with the first octet specifying ports 1 through 8, etc." ::= { clear 1 } counterClearOps OBJECT-TYPE SYNTAX INTEGER MAX-ACCESS read-write STATUS current DESCRIPTION "The corresponding bit is set to 1 to start the operation. The various bit positions are: BIT 1: clear interface counters BIT 2: clear pvc packet counters BIT 3: clear port ATM counters BIT 4: clear pvc ATM counters BIT 5: clear DHCP counters BIT 6: clear IGMP counters BIT 7: clear IGMP port counters BIT 8: clear MACFF ARP counters BIT 9: clear current lineperf BIT 10: clear current 15 minute lineperf BIT 11: clear current 1 day lineperf" ::= { clear 2 } counterClearVpi OBJECT-TYPE SYNTAX INTEGER (0..255) MAX-ACCESS read-write STATUS current DESCRIPTION "VPI of the pvc whose counters would be cleared." ::= { clear 3 } counterClearVci OBJECT-TYPE SYNTAX INTEGER (1..65535) MAX-ACCESS read-write STATUS current DESCRIPTION "VCI of the pvc whose counters would be cleared." ::= { clear 4 } END