CISCOSB-TIMESYNCHRONIZATION-MIB DEFINITIONS ::= BEGIN IMPORTS switch001 FROM CISCOSB-MIB Unsigned32, Integer32, IpAddress, MODULE-IDENTITY, OBJECT-TYPE FROM SNMPv2-SMI InetAddressType, InetAddress FROM INET-ADDRESS-MIB DisplayString, TEXTUAL-CONVENTION , RowStatus, TruthValue FROM SNMPv2-TC InterfaceIndex FROM IF-MIB; rlTimeSynchronization MODULE-IDENTITY LAST-UPDATED "200408030024Z" ORGANIZATION "Cisco Small Business" CONTACT-INFO "Postal: 170 West Tasman Drive San Jose , CA 95134-1706 USA Website: Cisco Small Business Home http://www.cisco.com/smb>;, Cisco Small Business Support Community " DESCRIPTION "The MIB module describes the private MIB for SNTP & TIME definitions." REVISION "200906180024Z" DESCRIPTION "Added support in DHCP timezone option." REVISION "200709060024Z" DESCRIPTION "Added rlClockStatus" REVISION "200311230024Z" DESCRIPTION "Initial revision" ::= { switch001 92 } rlTimeSyncMethodMode OBJECT IDENTIFIER ::= { rlTimeSynchronization 1 } rlSntpNtpClient OBJECT IDENTIFIER ::= { rlTimeSynchronization 2 } rlSntpNtpConfig OBJECT IDENTIFIER ::= { rlSntpNtpClient 1 } rlSntpConfig OBJECT IDENTIFIER ::= { rlSntpNtpClient 2 } rlNtpConfig OBJECT IDENTIFIER ::= { rlSntpNtpClient 3 } -- -- Textual Conventions -- NTPTimeStamp ::= TEXTUAL-CONVENTION DISPLAY-HINT "4d.4d" STATUS current DESCRIPTION "NTP timestamps are represented as a 64-bit unsigned fixed-point number, in seconds relative to 00:00 on 1 January 1900. The integer part is in the first 32 bits and the fraction part is in the last 32 bits." REFERENCE "D.L. Mills, 'Network Time Protocol (Version 3)', RFC-1305, March 1992, Section 3.1" SYNTAX OCTET STRING (SIZE (8)) NTPSignedTimeValue ::= TEXTUAL-CONVENTION DISPLAY-HINT "2d.2d" STATUS current DESCRIPTION "The time in seconds that could represent signed quantities like time delay with respect to some source. This textual-convention is specific to CISCOSB implementation of NTP where 32-bit integers are used for such quantities. The signed integer part is in the first 16 bits and the fraction part is in the last 16 bits." SYNTAX OCTET STRING (SIZE (4)) NTPStratum ::= TEXTUAL-CONVENTION STATUS current DESCRIPTION "Indicates the stratum of the clock. The stratum defines the accuracy of a time server. Higher the stratum, lower the accuracy. 0, unspecified 1, primary reference (e.g., calibrated atomic clock, radio clock) 2-255, secondary reference (via NTP)" REFERENCE "D.L. Mills, 'Network Time Protocol (Version 3)', RFC-1305, March 1992, Section 2.2" SYNTAX Integer32 (0..255) -- ---------------------------------------------------------------------- -- Global TimeSyncMethod -- ---------------------------------------------------------------------- RlTimeSyncMethod ::= TEXTUAL-CONVENTION STATUS current DESCRIPTION "Method to be used for time synchronization in the device." SYNTAX INTEGER { none(1), sntp(2), ntp(3) } RlDaylightSavingTimeMode ::= TEXTUAL-CONVENTION STATUS current DESCRIPTION "Daylight Saving Time - Recurring/Date/None." SYNTAX INTEGER { recurring(1), date(2), none(3) } rlTimeSyncMibVersion OBJECT-TYPE SYNTAX INTEGER MAX-ACCESS read-only STATUS current DESCRIPTION "TimeSync Mib Version." ::= { rlTimeSyncMethodMode 1 } rndTimeSyncManagedTime OBJECT-TYPE SYNTAX DisplayString (SIZE(6)) MAX-ACCESS read-write STATUS current DESCRIPTION "The time will be sent in the format hhmmss" ::= { rlTimeSyncMethodMode 2 } rndTimeSyncManagedDate OBJECT-TYPE SYNTAX DisplayString (SIZE(6)) MAX-ACCESS read-write STATUS current DESCRIPTION "The date will be sent in the format ddmmyy" ::= { rlTimeSyncMethodMode 3 } rndTimeSyncManagedDateTime OBJECT-TYPE SYNTAX DisplayString (SIZE(12)) MAX-ACCESS read-write STATUS current DESCRIPTION "The date and time will be sent in the format ddmmyyhhmmss" ::= { rlTimeSyncMethodMode 4 } rlTimeSyncMethod OBJECT-TYPE SYNTAX RlTimeSyncMethod MAX-ACCESS read-write STATUS current DESCRIPTION "Method to be used for time synchronization in the device." DEFVAL { none } ::= { rlTimeSyncMethodMode 5 } rlTimeZone OBJECT-TYPE SYNTAX DisplayString (SIZE(1..6)) MAX-ACCESS read-write STATUS current DESCRIPTION "Offset from Greenwich time (format [+/-]hh:mm)." ::= {rlTimeSyncMethodMode 6 } rlTimeZoneCode OBJECT-TYPE SYNTAX DisplayString (SIZE(0..16)) MAX-ACCESS read-write STATUS current DESCRIPTION "Code definition for current TimeZone." ::= {rlTimeSyncMethodMode 7 } rlDaylightSavingTimeMode OBJECT-TYPE SYNTAX RlDaylightSavingTimeMode MAX-ACCESS read-write STATUS current DESCRIPTION "Daylight Saving Time - Recurring/Date/None." DEFVAL { none } ::= { rlTimeSyncMethodMode 8 } rlDaylightSavingTimeStart OBJECT-TYPE SYNTAX OCTET STRING (SIZE(14)) MAX-ACCESS read-write STATUS current DESCRIPTION "Daylight Saving Time start date. In recurring mode (format 1): week wday month hh:mm In recurring mode (format 2): RJul n hh:mm In date mode: month day year hh:mm week: 0-6 (0=First, 6=Last) wday: 1-7 (Sunday-Saturday) month: 1-12 (January-December) day: 1-31 year: 0-99 (2000-2099) hh: 0-23 (hours) mm: 0-59 (minutes) n: 0-365 (zero-based Julian day of the year. Leap days shall be counted, and it is possible to refer to February 29). Format 2 for recurring mode is used only in the dynamic entry and should not be used in the static entry (with index 1)." ::= { rlTimeSyncMethodMode 9 } rlDaylightSavingTimeEnd OBJECT-TYPE SYNTAX OCTET STRING (SIZE(14)) MAX-ACCESS read-write STATUS current DESCRIPTION "Daylight Saving Time start date. In recurring mode (format 1): week wday month hh:mm In recurring mode (format 2): RJul n hh:mm In date mode: month day year hh:mm week: 0-6 (0=First, 6=Last) wday: 1-7 (Sunday-Saturday) month: 1-12 (January-December) day: 1-31 year: 0-99 (2000-2099) hh: 0-23 (hours) mm: 0-59 (minutes) n: 0-365 (zero-based Julian day of the year. Leap days shall be counted, and it is possible to refer to February 29). Format 2 for recurring mode is used only in the dynamic entry and should not be used in the static entry (with index 1)." ::= { rlTimeSyncMethodMode 10 } rlDaylightSavingTimeOffset OBJECT-TYPE SYNTAX Integer32 MAX-ACCESS read-write STATUS current DESCRIPTION "Daylight Saving Time - The number of minutes to add to the clock during summer time." DEFVAL { 60 } ::= { rlTimeSyncMethodMode 11 } rlDaylightSavingTimeCode OBJECT-TYPE SYNTAX DisplayString (SIZE(0..16)) MAX-ACCESS read-write STATUS current DESCRIPTION "Code definition for current Daylight Saving Time." ::= {rlTimeSyncMethodMode 12 } rlTZDSTOffset OBJECT-TYPE SYNTAX INTEGER MAX-ACCESS read-only STATUS current DESCRIPTION "Local Time Zone and Daylight Saving Time offset in seconds." ::= { rlTimeSyncMethodMode 13 } rlTimeZoneName OBJECT-TYPE SYNTAX DisplayString (SIZE(0..16)) MAX-ACCESS read-write STATUS current DESCRIPTION "Human readable string describing Local Time Zone and Daylight Saving Time." ::= {rlTimeSyncMethodMode 14 } -- -- TimeZone table -- -- TimeZone table aimed to replace next mibs: -- rlTimeSyncMethod -- rlTimeZone -- rlTimeZoneCode -- rlDaylightSavingTimeMode -- rlDaylightSavingTimeStart -- rlDaylightSavingTimeEnd -- rlDaylightSavingTimeOffset -- rlDaylightSavingTimeCode -- rlTZDSTOffset -- rlTimeZoneName -- Table consist of one entry (with index = 1) and each field corresponding -- to one of this MIB scalars, holding Timezone and Summertime static information. -- In case DHCP timezone option is supported, the table will contain another row, -- with index = 2, that will contain dynamic values for Timezone and Summertime -- received through DHCP. rlTimeZoneTable OBJECT-TYPE SYNTAX SEQUENCE OF RlTimeZoneEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "TimeZone information." ::= { rlTimeSyncMethodMode 15 } rlTimeZoneEntry OBJECT-TYPE SYNTAX RlTimeZoneEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "The row definition for this table." INDEX { rlTimeZoneIndex } ::= { rlTimeZoneTable 1 } RlTimeZoneEntry ::= SEQUENCE { rlTimeZoneIndex INTEGER, rlTimeZoneTimeSyncMethod RlTimeSyncMethod, rlTimeZoneTimeZoneOffset DisplayString (SIZE(1..6)), rlTimeZoneTimeZoneCode DisplayString (SIZE(0..16)), rlTimeZoneDaylightSavingTimeMode RlDaylightSavingTimeMode, rlTimeZoneDaylightSavingTimeStart OCTET STRING (SIZE(14)), rlTimeZoneDaylightSavingTimeEnd OCTET STRING (SIZE(14)), rlTimeZoneDaylightSavingTimeOffset Integer32, rlTimeZoneDaylightSavingTimeCode DisplayString (SIZE(0..16)), rlTimeZoneTZDSTOffset INTEGER, rlTimeZoneTimeZoneName DisplayString (SIZE(0..16)), rlTimeZoneDataType INTEGER, rlTimeZoneDataSourceIfIndex INTEGER, rlTimeZoneDataDynamicConfSource INTEGER } rlTimeZoneIndex OBJECT-TYPE SYNTAX INTEGER (1..2) MAX-ACCESS not-accessible STATUS current DESCRIPTION "Entry index. A row with index 2 will be existing in case the DHCP timezone is supported, and will contain Timezone and Summertime dynamic values. Using index 2 in SET operations is allowed only for SNMP inner clients (SNMPServ users), on condition that DHCP timezone option is supported." ::= { rlTimeZoneEntry 1 } rlTimeZoneTimeSyncMethod OBJECT-TYPE SYNTAX RlTimeSyncMethod MAX-ACCESS read-write STATUS current DESCRIPTION "Method to be used for time synchronization in the device." DEFVAL { none } ::= { rlTimeZoneEntry 2 } rlTimeZoneTimeZoneOffset OBJECT-TYPE SYNTAX DisplayString (SIZE(1..6)) MAX-ACCESS read-write STATUS current DESCRIPTION "Offset from Greenwich time (format [+/-]hh:mm)." ::= { rlTimeZoneEntry 3 } rlTimeZoneTimeZoneCode OBJECT-TYPE SYNTAX DisplayString (SIZE(0..16)) MAX-ACCESS read-write STATUS current DESCRIPTION "Code definition for current TimeZone." ::= { rlTimeZoneEntry 4 } rlTimeZoneDaylightSavingTimeMode OBJECT-TYPE SYNTAX RlDaylightSavingTimeMode MAX-ACCESS read-write STATUS current DESCRIPTION "Daylight Saving Time - Recurring/Date/None." DEFVAL { none } ::= { rlTimeZoneEntry 5 } rlTimeZoneDaylightSavingTimeStart OBJECT-TYPE SYNTAX OCTET STRING (SIZE(14)) MAX-ACCESS read-write STATUS current DESCRIPTION "Daylight Saving Time start date. In recurring mode (format 1): week wday month hh:mm In recurring mode (format 2): RJul n hh:mm In date mode: month day year hh:mm week: 0-6 (0=First, 6=Last) wday: 1-7 (Sunday-Saturday) month: 1-12 (January-December) day: 1-31 year: 0-99 (2000-2099) hh: 0-23 (hours) mm: 0-59 (minutes) n: 0-365 (zero-based Julian day of the year. Leap days shall be counted, and it is possible to refer to February 29). Format 2 for recurring mode is used only in the dynamic entry and should not be used in the static entry (with index 1)." ::= { rlTimeZoneEntry 6 } rlTimeZoneDaylightSavingTimeEnd OBJECT-TYPE SYNTAX OCTET STRING (SIZE(14)) MAX-ACCESS read-write STATUS current DESCRIPTION "Daylight Saving Time start date. In recurring mode (format 1): week wday month hh:mm In recurring mode (format 2): RJul n hh:mm In date mode: month day year hh:mm week: 0-6 (0=First, 6=Last) wday: 1-7 (Sunday-Saturday) month: 1-12 (January-December) day: 1-31 year: 0-99 (2000-2099) hh: 0-23 (hours) mm: 0-59 (minutes) n: 0-365 (zero-based Julian day of the year. Leap days shall be counted, and it is possible to refer to February 29). Format 2 for recurring mode is used only in the dynamic entry and should not be used in the static entry (with index 1)." ::= { rlTimeZoneEntry 7 } rlTimeZoneDaylightSavingTimeOffset OBJECT-TYPE SYNTAX Integer32 MAX-ACCESS read-write STATUS current DESCRIPTION "Daylight Saving Time - The number of minutes to add to the clock during summer time." DEFVAL { 60 } ::= { rlTimeZoneEntry 8 } rlTimeZoneDaylightSavingTimeCode OBJECT-TYPE SYNTAX DisplayString (SIZE(0..16)) MAX-ACCESS read-write STATUS current DESCRIPTION "Code definition for current Daylight Saving Time." ::= { rlTimeZoneEntry 9 } rlTimeZoneTZDSTOffset OBJECT-TYPE SYNTAX INTEGER MAX-ACCESS read-only STATUS current DESCRIPTION "Local Time Zone and Daylight Saving Time offset in seconds." ::= { rlTimeZoneEntry 10 } rlTimeZoneTimeZoneName OBJECT-TYPE SYNTAX DisplayString (SIZE(0..16)) MAX-ACCESS read-write STATUS current DESCRIPTION "Human readable string describing Local Time Zone and Daylight Saving Time." ::= { rlTimeZoneEntry 11 } rlTimeZoneDataType OBJECT-TYPE SYNTAX INTEGER { static(1), dynamic(2) } MAX-ACCESS read-only STATUS current DESCRIPTION "The type of data in this entry: static or dynamic." DEFVAL { static } ::= { rlTimeZoneEntry 12 } rlTimeZoneDataSourceIfIndex OBJECT-TYPE SYNTAX INTEGER MAX-ACCESS read-write STATUS current DESCRIPTION "IfIndex of the interface through which the dynamic data of this row has been learned. The value of this field will be 0 if rlTimeZoneTimeDataType is static (since it is relevant only for dynamic entry), and this is the only value allowed for SET in this case." DEFVAL { 0 } ::= { rlTimeZoneEntry 13 } rlTimeZoneDataDynamicConfSource OBJECT-TYPE SYNTAX INTEGER { none(1), dhcpv4(2), dhcpv6(3) } MAX-ACCESS read-write STATUS current DESCRIPTION "The source of dynamic data in this entry, for example: dhcpv4. Values other than 'none' are relevant only for dynamic entry." DEFVAL { none } ::= { rlTimeZoneEntry 14 } rlClockStatus OBJECT-TYPE SYNTAX INTEGER { invalid(1), manuallySet(2), synchronizedBySntp(3) } MAX-ACCESS read-only STATUS current DESCRIPTION "Current status of the clock. The value 'invalid' means time is meaninglesss, since it has neither been manually configured nor achieved as a result of SNTP synchronization." ::= {rlTimeSyncMethodMode 16 } rlDhcpTimezoneOptionEnabled OBJECT-TYPE SYNTAX TruthValue MAX-ACCESS read-write STATUS current DESCRIPTION "Specifies whether the DHCP Timezone option (DHCPv4 option 100) is supported in the system. Setting this value to FALSE, will clear Timezone and Summertime dynamic configuration, so that: 1) rlTimeZoneTimeZoneCode and rlTimeZoneDaylightSavingTimeCode length will be 0 for rlTimeZoneEntry whose index = 2 (dynamic entry). 2) the operative values of Timezone and Summertime will be those statically configured. Thus, GET operations on the following MIB scalars will result is static values: rlTimeZone, rlTimeZoneCode, rlDaylightSavingTimeMode, rlDaylightSavingTimeStart, rlDaylightSavingTimeEnd, rlDaylightSavingTimeOffset, rlDaylightSavingTimeCode, rlTZDSTOffset." ::= {rlTimeSyncMethodMode 17 } rlAutomaticClockSetFromPCEnabled OBJECT-TYPE SYNTAX TruthValue MAX-ACCESS read-write STATUS current DESCRIPTION "Specifies whether automatic set of time and date is permitted from connected host PC. The feature is meant to be used in order to initialize the clock after reboot (if SNTP is not in use), since the device does not have a realtime clock." DEFVAL { false } ::= {rlTimeSyncMethodMode 18 } rlTimeAndDateHaveBeenSet OBJECT-TYPE SYNTAX TruthValue MAX-ACCESS read-only STATUS current DESCRIPTION "Indicates whether the time and date have been set in the device, manually or through SNTP synchronization. If only time has been set, the value of this MIB will be FALSE. If only date has been set, the value of this MIB will be FALSE." ::= {rlTimeSyncMethodMode 19 } -- ---------------------------------------------------------------------- -- SNTP/NTP client configuration parameters -- ---------------------------------------------------------------------- RlSntpNtpSyncType ::= TEXTUAL-CONVENTION STATUS current DESCRIPTION "Method to be used for time synchronization in the device." SYNTAX INTEGER { none(1), unicast(2), anycast(3), broadcast(4) } RlSntpNtpSyncEntryType ::= TEXTUAL-CONVENTION STATUS current DESCRIPTION "Entry in rlSntpNtpConfigSrvTable." SYNTAX INTEGER { primaryPollSrv(1), syncSrv(2) } rlSntpNtpMibVersion OBJECT-TYPE SYNTAX INTEGER MAX-ACCESS read-only STATUS current DESCRIPTION "SntpNtp Mib Version." ::= { rlSntpNtpConfig 1 } rlSntpNtpConfigMode OBJECT-TYPE SYNTAX INTEGER { none(1), unicast(2), anycast(3), multicast(4), unicastAnycast(5), unicastMulticast(6), anycastMulticast(7), unicastAnycastMulticast(8) } MAX-ACCESS read-only STATUS current DESCRIPTION "Current configuration operational mode of SNTP/NTP client." DEFVAL { none } ::= { rlSntpNtpConfig 2 } rlSntpNtpConfigSysStratum OBJECT-TYPE SYNTAX NTPStratum MAX-ACCESS read-only STATUS current DESCRIPTION "The stratum of the local clock. If the value is set to 1, i.e., this is a primary reference, then the Primary-Clock procedure described in Section 3.4.6, in RFC-1305 is invoked." ::= { rlSntpNtpConfig 3 } rlSntpNtpConfigPollInterval OBJECT-TYPE SYNTAX INTEGER MAX-ACCESS read-write STATUS current DESCRIPTION "Period of time (in seconds) between succesive attempts to perform an update via SNTP." DEFVAL { 1024 } ::= { rlSntpNtpConfig 4 } rlSntpNtpConfigPrimaryPollSrvAddr OBJECT-TYPE SYNTAX IpAddress MAX-ACCESS read-only STATUS current DESCRIPTION "Ip Address of a trusted SNTP server for polling." ::= { rlSntpNtpConfig 5 } rlSntpNtpConfigPrimaryPollSrvMrid OBJECT-TYPE SYNTAX INTEGER MAX-ACCESS read-only STATUS current DESCRIPTION "The mrid of the primary server." ::= { rlSntpNtpConfig 6 } rlSntpNtpConfigPrimaryPollSrvIfIndex OBJECT-TYPE SYNTAX INTEGER MAX-ACCESS read-only STATUS current DESCRIPTION "The interface addressed of the primary server." ::= { rlSntpNtpConfig 7 } rlSntpNtpConfigPrimaryPollSrvStratum OBJECT-TYPE SYNTAX NTPStratum MAX-ACCESS read-only STATUS current DESCRIPTION "The stratum of the primary polling server." ::= { rlSntpNtpConfig 8 } rlSntpNtpConfigSyncSrvAddr OBJECT-TYPE SYNTAX IpAddress MAX-ACCESS read-only STATUS current DESCRIPTION "Ip Address of the synced server." ::= { rlSntpNtpConfig 9 } rlSntpNtpConfigSyncSrvMrid OBJECT-TYPE SYNTAX INTEGER MAX-ACCESS read-only STATUS current DESCRIPTION "The mrid of the synced server." ::= { rlSntpNtpConfig 10 } rlSntpNtpConfigSyncSrvIfIndex OBJECT-TYPE SYNTAX INTEGER MAX-ACCESS read-only STATUS current DESCRIPTION "The interface addressed of the synced server." ::= { rlSntpNtpConfig 11 } rlSntpNtpConfigSyncSrvType OBJECT-TYPE SYNTAX RlSntpNtpSyncType MAX-ACCESS read-only STATUS current DESCRIPTION "Synced server type." DEFVAL { none } ::= { rlSntpNtpConfig 12 } rlSntpNtpConfigSyncSrvStratum OBJECT-TYPE SYNTAX NTPStratum MAX-ACCESS read-only STATUS current DESCRIPTION "The stratum of the synced server." ::= { rlSntpNtpConfig 13 } rlSntpNtpConfigRetryTimeout OBJECT-TYPE SYNTAX Integer32 MAX-ACCESS read-only STATUS current DESCRIPTION "SNTP/NTP requests Retry Interval." ::= { rlSntpNtpConfig 14 } rlSntpNtpConfigRetryCnt OBJECT-TYPE SYNTAX Integer32 MAX-ACCESS read-only STATUS current DESCRIPTION "SNTP/NTP requests Retry Count." ::= { rlSntpNtpConfig 15 } -- ---------------------------------------------------------------------- -- SNTP Config Servers -- ---------------------------------------------------------------------- -- Will replace next MIBs: -- rlSntpNtpConfigPrimaryPollSrvAddr -- rlSntpNtpConfigPrimaryPollSrvMrid -- rlSntpNtpConfigPrimaryPollSrvIfIndex -- rlSntpNtpConfigPrimaryPollSrvStratum -- rlSntpNtpConfigSyncSrvAddr -- rlSntpNtpConfigSyncSrvMrid -- rlSntpNtpConfigSyncSrvIfIndex -- rlSntpNtpConfigSyncSrvType -- rlSntpNtpConfigSyncSrvStratum rlSntpNtpConfigSrvTable OBJECT-TYPE SYNTAX SEQUENCE OF RlSntpNtpConfigSrvEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "A table containing information about config servers." ::= { rlSntpNtpConfig 16 } rlSntpNtpConfigSrvEntry OBJECT-TYPE SYNTAX RlSntpNtpConfigSrvEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "Entry in rlSntpNtpConfigSrvTable." INDEX { rlSntpNtpConfigSrvEntryType } ::= { rlSntpNtpConfigSrvTable 1 } RlSntpNtpConfigSrvEntry ::= SEQUENCE { rlSntpNtpConfigSrvEntryType RlSntpNtpSyncEntryType, rlSntpNtpConfigSrvInetAddressType InetAddressType, rlSntpNtpConfigSrvInetAddress InetAddress, rlSntpNtpConfigSrvMrid INTEGER, rlSntpNtpConfigSrvIfIndex INTEGER, rlSntpNtpConfigSrvSyncType RlSntpNtpSyncType, rlSntpNtpConfigSrvStratum NTPStratum } rlSntpNtpConfigSrvEntryType OBJECT-TYPE SYNTAX RlSntpNtpSyncEntryType MAX-ACCESS not-accessible STATUS current DESCRIPTION "Server type: Synchronize Server or Primary Poll Server." ::= { rlSntpNtpConfigSrvEntry 1 } rlSntpNtpConfigSrvInetAddressType OBJECT-TYPE SYNTAX InetAddressType MAX-ACCESS read-only STATUS current DESCRIPTION "Server inet address type." ::= { rlSntpNtpConfigSrvEntry 2 } rlSntpNtpConfigSrvInetAddress OBJECT-TYPE SYNTAX InetAddress MAX-ACCESS read-only STATUS current DESCRIPTION "Server inet address." ::= { rlSntpNtpConfigSrvEntry 3 } rlSntpNtpConfigSrvMrid OBJECT-TYPE SYNTAX INTEGER MAX-ACCESS read-only STATUS current DESCRIPTION "The mrid of the server." ::= { rlSntpNtpConfigSrvEntry 4 } rlSntpNtpConfigSrvIfIndex OBJECT-TYPE SYNTAX INTEGER MAX-ACCESS read-only STATUS current DESCRIPTION "The interface addressed of the server." ::= { rlSntpNtpConfigSrvEntry 5 } rlSntpNtpConfigSrvSyncType OBJECT-TYPE SYNTAX RlSntpNtpSyncType MAX-ACCESS read-only STATUS current DESCRIPTION "The type of synchronization." ::= { rlSntpNtpConfigSrvEntry 6 } rlSntpNtpConfigSrvStratum OBJECT-TYPE SYNTAX NTPStratum MAX-ACCESS read-only STATUS current DESCRIPTION "The stratum of the synced server." ::= { rlSntpNtpConfigSrvEntry 7 } -- ---------------------------------------------------------------------- -- SNTP client configuration parameters -- ---------------------------------------------------------------------- rlSntpClientMode OBJECT-TYPE SYNTAX INTEGER { none(1), active(2), passive(3) } MAX-ACCESS read-only STATUS current DESCRIPTION "Current operational mode of SNTP client." DEFVAL { none } ::= { rlSntpConfig 1 } rlSntpUnicastAdminState OBJECT-TYPE SYNTAX INTEGER { enabled(1), disabled(2) } MAX-ACCESS read-write STATUS current DESCRIPTION "SNTP Unicast Administrative state - Enable/Disable SNTP. In case of reinitializing polling or time synchronization this MIB is modified. The MIB can be enabled even thought it is already enabled." DEFVAL { disabled } ::= { rlSntpConfig 2 } rlSntpBroadcastAdminState OBJECT-TYPE SYNTAX INTEGER { enabled(1), disabled(2), ipv4OnlyEnabled(3), ipv6OnlyEnabled(4) } MAX-ACCESS read-write STATUS current DESCRIPTION "SNTP Broadcast Administrative state - Enable/Disable SNTP. In case of reinitializing polling or time synchronization this MIB is modified. The MIB can be enabled even thought it is already enabled." DEFVAL { disabled } ::= { rlSntpConfig 3 } rlSntpAnycastAdminState OBJECT-TYPE SYNTAX INTEGER { enabled(1), disabled(2), ipv4OnlyEnabled(3), ipv6OnlyEnabled(4) } MAX-ACCESS read-write STATUS current DESCRIPTION "SNTP Anycast Administrative state - Enable/Disable SNTP. In case of reinitializing polling or time synchronization this MIB is modified. The MIB can be enabled even thought it is already enabled." DEFVAL { disabled } ::= { rlSntpConfig 4 } rlSntpUnicastPollState OBJECT-TYPE SYNTAX TruthValue MAX-ACCESS read-write STATUS current DESCRIPTION "SNTP Unicast poll state - TRUE for polled." DEFVAL { false } ::= { rlSntpConfig 5 } rlSntpBroadcastPollState OBJECT-TYPE SYNTAX TruthValue MAX-ACCESS read-write STATUS current DESCRIPTION "SNTP Broadcast poll state - TRUE for polled." DEFVAL { false } ::= { rlSntpConfig 6 } rlSntpAnycastPollState OBJECT-TYPE SYNTAX TruthValue MAX-ACCESS read-write STATUS current DESCRIPTION "SNTP Anycast poll state - TRUE for polled." DEFVAL { false } ::= { rlSntpConfig 7 } rlSntpAuthenticationState OBJECT-TYPE SYNTAX INTEGER { enabled(1), disabled(2) } MAX-ACCESS read-write STATUS current DESCRIPTION "SNTP authentication state- Enable/Disable SNTP." DEFVAL { disabled } ::= { rlSntpConfig 8 } rlTimeValidFlag OBJECT-TYPE SYNTAX TruthValue MAX-ACCESS read-write STATUS current DESCRIPTION "Is time valid." DEFVAL { false } ::= { rlSntpConfig 9 } -- ---------------------------------------------------------------------- -- Table for configuring Interfaces (Broadcast) -- ---------------------------------------------------------------------- rlSntpConfigBroadcastTable OBJECT-TYPE SYNTAX SEQUENCE OF RlSntpBroadcastEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "A table containing broadcast mode information per interface." ::= { rlSntpConfig 10 } rlSntpBroadcastEntry OBJECT-TYPE SYNTAX RlSntpBroadcastEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "Private paramters for interface: sntp status, broadcast mode." INDEX { rlSntpBroadcastIfIndex } ::= { rlSntpConfigBroadcastTable 1 } RlSntpBroadcastEntry ::= SEQUENCE { rlSntpBroadcastIfIndex INTEGER, rlSntpBroadcastIfAdminState INTEGER, rlSntpBroadcastMode INTEGER, rlSntpBroadcastPolled TruthValue, rlSntpBroadcastAddress IpAddress, rlSntpBroadcastStratum NTPStratum, rlSntpBroadcastLastResp NTPTimeStamp, rlSntpBroadcastStatus INTEGER, rlSntpBroadcastOffset NTPTimeStamp, rlSntpBroadcastDelay NTPSignedTimeValue, rlSntpBroadcastRowStatus RowStatus } rlSntpBroadcastIfIndex OBJECT-TYPE SYNTAX INTEGER MAX-ACCESS not-accessible STATUS current DESCRIPTION "The interface addressed by this entry." ::= {rlSntpBroadcastEntry 1} rlSntpBroadcastIfAdminState OBJECT-TYPE SYNTAX INTEGER { enabled(1), disabled(2) } MAX-ACCESS read-write STATUS current DESCRIPTION "SNTP interface Adminstrative state- Enable/Disable SNTP. In case of reinitializing polling or time synchronization this MIB is modified. The MIB can be enabled even thought it is already enabled." DEFVAL { disabled } ::= { rlSntpBroadcastEntry 2 } rlSntpBroadcastMode OBJECT-TYPE SYNTAX INTEGER { none(1), receive(2), send(3), receiveSend(4) } MAX-ACCESS read-write STATUS current DESCRIPTION "SNTP/NTP Broadcast Mode. none - no broadcast SNTP packets are received or sent. Receive - host only receive SNTP packets that were sent to broadcast address (were not directed to the host). This is multicast mode in the RFC. Send - host only send SNTP packets and wait for replies directed to the host. This is anycast mode in the RFC. ReceiveSend - host receive broadcast messages (destination is broadcast address in the received messages) and send SNTP packets to wait for replies directed to the host (destination address of the reply is the host address). This mode combines anycast and multicast modes in the RFC." DEFVAL { receiveSend } ::= { rlSntpBroadcastEntry 3 } rlSntpBroadcastPolled OBJECT-TYPE SYNTAX TruthValue MAX-ACCESS read-write STATUS current DESCRIPTION "TRUE if participating in polling cycle, else FALSE." DEFVAL { false } ::= { rlSntpBroadcastEntry 4 } rlSntpBroadcastAddress OBJECT-TYPE SYNTAX IpAddress MAX-ACCESS read-only STATUS current DESCRIPTION "Ip Address of a trusted SNTP server." ::= { rlSntpBroadcastEntry 5 } rlSntpBroadcastStratum OBJECT-TYPE SYNTAX NTPStratum MAX-ACCESS read-only STATUS current DESCRIPTION "The stratum of this server." ::= { rlSntpBroadcastEntry 6 } rlSntpBroadcastLastResp OBJECT-TYPE SYNTAX NTPTimeStamp MAX-ACCESS read-only STATUS current DESCRIPTION "SNTP Broadcast Last Response Time" ::= { rlSntpBroadcastEntry 7 } rlSntpBroadcastStatus OBJECT-TYPE SYNTAX INTEGER { unknown(1), inProcess(2), up(3), down(4) } MAX-ACCESS read-only STATUS current DESCRIPTION "The Operational State of the remote IP Address of the SNTP Broadcast. unknown - requests were not sent yet. inProcess - replies were not received yet. up - server sent SNTP packets. down - server stopped sending SNTP packets." DEFVAL { unknown } ::= { rlSntpBroadcastEntry 8 } rlSntpBroadcastOffset OBJECT-TYPE SYNTAX NTPTimeStamp UNITS "seconds" MAX-ACCESS read-only STATUS current DESCRIPTION "The estimated offset of the server's clock relative to the local clock, in seconds. The host determines the value of this object using the algorithm described in RFC 2030." ::= { rlSntpBroadcastEntry 9 } rlSntpBroadcastDelay OBJECT-TYPE SYNTAX NTPSignedTimeValue UNITS "seconds" MAX-ACCESS read-only STATUS current DESCRIPTION "The estimated round-trip delay of the server's clock relative to the local clock over the network path between them, in seconds. The host determines the value of this object using the algorithm described in RFC 2030." ::= { rlSntpBroadcastEntry 10 } rlSntpBroadcastRowStatus OBJECT-TYPE SYNTAX RowStatus MAX-ACCESS read-write STATUS current DESCRIPTION "The Status of this SNTP broadcast interface information." ::= { rlSntpBroadcastEntry 11 } -- ---------------------------------------------------------------------- -- Table for configuring Interfaces (Anycast) -- ---------------------------------------------------------------------- rlSntpConfigAnycastTable OBJECT-TYPE SYNTAX SEQUENCE OF RlSntpAnycastEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "A table containing anycast information per interface." ::= { rlSntpConfig 11 } rlSntpAnycastEntry OBJECT-TYPE SYNTAX RlSntpAnycastEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "Private paramters for interface: server info." INDEX { rlSntpAnycastIfIndex } ::= { rlSntpConfigAnycastTable 1 } RlSntpAnycastEntry ::= SEQUENCE { rlSntpAnycastIfIndex INTEGER, rlSntpAnycastAddress IpAddress, rlSntpAnycastStratum NTPStratum, rlSntpAnycastLastResp NTPTimeStamp, rlSntpAnycastStatus INTEGER, rlSntpAnycastOffset NTPTimeStamp, rlSntpAnycastDelay NTPSignedTimeValue, rlSntpAnycastRowStatus RowStatus } rlSntpAnycastIfIndex OBJECT-TYPE SYNTAX INTEGER MAX-ACCESS not-accessible STATUS current DESCRIPTION "The interface addressed by this entry." ::= {rlSntpAnycastEntry 1} rlSntpAnycastAddress OBJECT-TYPE SYNTAX IpAddress MAX-ACCESS read-only STATUS current DESCRIPTION "Ip Address of a trusted SNTP server." ::= { rlSntpAnycastEntry 2 } rlSntpAnycastStratum OBJECT-TYPE SYNTAX NTPStratum MAX-ACCESS read-only STATUS current DESCRIPTION "The stratum of this server." ::= { rlSntpAnycastEntry 3 } rlSntpAnycastLastResp OBJECT-TYPE SYNTAX NTPTimeStamp MAX-ACCESS read-only STATUS current DESCRIPTION "SNTP Anycast Last Response Time" ::= { rlSntpAnycastEntry 4 } rlSntpAnycastStatus OBJECT-TYPE SYNTAX INTEGER { unknown(1), inProcess(2), up(3), down(4) } MAX-ACCESS read-only STATUS current DESCRIPTION "The Operational State of the remote IP Address of the SNTP Anycast. unknown - requests were not sent yet. inProcess - replies were not received yet. up - server sent SNTP packets. down - server stopped sending SNTP packets." DEFVAL { unknown } ::= { rlSntpAnycastEntry 5 } rlSntpAnycastOffset OBJECT-TYPE SYNTAX NTPTimeStamp UNITS "seconds" MAX-ACCESS read-only STATUS current DESCRIPTION "The estimated offset of the server's clock relative to the local clock, in seconds. The host determines the value of this object using the algorithm described in RFC 2030." ::= { rlSntpAnycastEntry 6 } rlSntpAnycastDelay OBJECT-TYPE SYNTAX NTPSignedTimeValue UNITS "seconds" MAX-ACCESS read-only STATUS current DESCRIPTION "The estimated round-trip delay of the server's clock relative to the local clock over the network path between them, in seconds. The host determines the value of this object using the algorithm described in RFC 2030." ::= { rlSntpAnycastEntry 7 } rlSntpAnycastRowStatus OBJECT-TYPE SYNTAX RowStatus MAX-ACCESS read-write STATUS current DESCRIPTION "The Status of this SNTP anycast interface information." ::= { rlSntpAnycastEntry 8 } -- ---------------------------------------------------------------------- -- Table for configuring Servers (Unicast) -- ---------------------------------------------------------------------- rlSntpConfigServerTable OBJECT-TYPE SYNTAX SEQUENCE OF RlSntpServerEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "A table containing trusted SNTP servers to be queried in unicast or broadcast mode." ::= { rlSntpConfig 12 } rlSntpServerEntry OBJECT-TYPE SYNTAX RlSntpServerEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "A trusted server." INDEX { rlSntpServerAddress } ::= { rlSntpConfigServerTable 1 } RlSntpServerEntry ::= SEQUENCE { rlSntpServerAddress IpAddress, rlSntpServerPolled TruthValue, rlSntpServerStratum NTPStratum, rlSntpServerLastResp NTPTimeStamp, rlSntpServerStatus INTEGER, rlSntpServersOffset NTPTimeStamp, rlSntpServersDelay NTPSignedTimeValue, rlSntpServersKeyIdentifier Unsigned32, rlSntpServerRowStatus RowStatus } rlSntpServerAddress OBJECT-TYPE SYNTAX IpAddress MAX-ACCESS not-accessible STATUS current DESCRIPTION "Ip Address of a trusted SNTP server." ::= { rlSntpServerEntry 1 } rlSntpServerPolled OBJECT-TYPE SYNTAX TruthValue MAX-ACCESS read-write STATUS current DESCRIPTION "TRUE if participating in polling cycle, else FALSE." DEFVAL { false } ::= { rlSntpServerEntry 2 } rlSntpServerStratum OBJECT-TYPE SYNTAX NTPStratum MAX-ACCESS read-only STATUS current DESCRIPTION "The stratum of this server." ::= { rlSntpServerEntry 3 } rlSntpServerLastResp OBJECT-TYPE SYNTAX NTPTimeStamp MAX-ACCESS read-only STATUS current DESCRIPTION "SNTP Server Last Response Time" ::= { rlSntpServerEntry 4 } rlSntpServerStatus OBJECT-TYPE SYNTAX INTEGER { unknown(1), inProcess(2), up(3), down(4) } MAX-ACCESS read-only STATUS current DESCRIPTION "The Operational State of the remote IP Address of the SNTP Server. unknown - requests were not sent yet. inProcess - replies were not received yet. up - server sent SNTP packets. down - server stopped sending SNTP packets." DEFVAL { unknown } ::= { rlSntpServerEntry 5 } rlSntpServersOffset OBJECT-TYPE SYNTAX NTPTimeStamp UNITS "seconds" MAX-ACCESS read-only STATUS current DESCRIPTION "The estimated offset of the server's clock relative to the local clock, in seconds. The host determines the value of this object using the algorithm described in RFC 2030." ::= { rlSntpServerEntry 6 } rlSntpServersDelay OBJECT-TYPE SYNTAX NTPSignedTimeValue UNITS "seconds" MAX-ACCESS read-only STATUS current DESCRIPTION "The estimated round-trip delay of the server's clock relative to the local clock over the network path between them, in seconds. The host determines the value of this object using the algorithm described in RFC 2030." ::= { rlSntpServerEntry 7 } rlSntpServersKeyIdentifier OBJECT-TYPE SYNTAX Unsigned32 MAX-ACCESS read-write STATUS current DESCRIPTION "Authentication key identifier. The valid range is 1-4294967295. Value zero, means no authentication is being done." ::= { rlSntpServerEntry 8 } rlSntpServerRowStatus OBJECT-TYPE SYNTAX RowStatus MAX-ACCESS read-write STATUS current DESCRIPTION "The Status of this SNTP server information." ::= { rlSntpServerEntry 9 } -- ---------------------------------------------------------------------- -- Table for configuring authentication keys -- ---------------------------------------------------------------------- rlSntpConfigAuthenticationTable OBJECT-TYPE SYNTAX SEQUENCE OF RlSntpAuthenticationEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "A table authentication keys." ::= { rlSntpConfig 13 } rlSntpAuthenticationEntry OBJECT-TYPE SYNTAX RlSntpAuthenticationEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "Keys information for authenticationof NTP packets." INDEX { rlSntpAuthenticationKeyID } ::= { rlSntpConfigAuthenticationTable 1 } RlSntpAuthenticationEntry ::= SEQUENCE { rlSntpAuthenticationKeyID Unsigned32 (1..4294967295), rlSntpAuthenticationKeyValue DisplayString, rlSntpAuthenticationKeyState INTEGER, rlSntpAuthenticationRowStatus RowStatus } rlSntpAuthenticationKeyID OBJECT-TYPE SYNTAX Unsigned32 (1..4294967295) MAX-ACCESS read-write STATUS current DESCRIPTION "The key identifier. Valid rabge for key identifier is 1-4294967295." ::= {rlSntpAuthenticationEntry 1} rlSntpAuthenticationKeyValue OBJECT-TYPE SYNTAX DisplayString (SIZE(1..8)) MAX-ACCESS read-write STATUS current DESCRIPTION "Key value." ::= { rlSntpAuthenticationEntry 2 } rlSntpAuthenticationKeyState OBJECT-TYPE SYNTAX INTEGER { enabled(1), disabled(2) } MAX-ACCESS read-write STATUS current DESCRIPTION "Authentication key state - Enable/Disable key." DEFVAL { disabled } ::= { rlSntpAuthenticationEntry 3 } rlSntpAuthenticationRowStatus OBJECT-TYPE SYNTAX RowStatus MAX-ACCESS read-write STATUS current DESCRIPTION "The Status of this Authentication key information." ::= { rlSntpAuthenticationEntry 4 } rlSntpPort OBJECT-TYPE SYNTAX INTEGER (1.. 65535) MAX-ACCESS read-write STATUS current DESCRIPTION "User defined SNTP port." DEFVAL { 123 } ::= { rlSntpConfig 14 } -- ---------------------------------------------------------------------- -- IPv6 Support -- ---------------------------------------------------------------------- -- ---------------------------------------------------------------------- -- IPv6: Table for configuring Interfaces (Broadcast) -- ---------------------------------------------------------------------- rlSntpConfigBroadcastInetTable OBJECT-TYPE SYNTAX SEQUENCE OF RlSntpBroadcastInetEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "A table containing broadcast mode information per interface." ::= { rlSntpConfig 15 } rlSntpBroadcastInetEntry OBJECT-TYPE SYNTAX RlSntpBroadcastInetEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "Private paramters for interface: sntp status, broadcast mode." INDEX { rlSntpBroadcastInetIfIndex } ::= { rlSntpConfigBroadcastInetTable 1 } RlSntpBroadcastInetEntry ::= SEQUENCE { rlSntpBroadcastInetIfIndex INTEGER, rlSntpBroadcastInetIfAdminState INTEGER, rlSntpBroadcastInetMode INTEGER, rlSntpBroadcastInetPolled TruthValue, rlSntpBroadcastInetAddressType InetAddressType, rlSntpBroadcastInetAddress InetAddress, rlSntpBroadcastInetStratum NTPStratum, rlSntpBroadcastInetLastResp NTPTimeStamp, rlSntpBroadcastInetStatus INTEGER, rlSntpBroadcastInetOffset NTPTimeStamp, rlSntpBroadcastInetDelay NTPSignedTimeValue, rlSntpBroadcastInetRowStatus RowStatus } rlSntpBroadcastInetIfIndex OBJECT-TYPE SYNTAX INTEGER MAX-ACCESS not-accessible STATUS current DESCRIPTION "The interface addressed by this entry." ::= {rlSntpBroadcastInetEntry 1} rlSntpBroadcastInetIfAdminState OBJECT-TYPE SYNTAX INTEGER { enabled(1), disabled(2) } MAX-ACCESS read-write STATUS current DESCRIPTION "SNTP interface Adminstrative state- Enable/Disable SNTP. In case of reinitializing polling or time synchronization this MIB is modified. The MIB can be enabled even thought it is already enabled." DEFVAL { disabled } ::= { rlSntpBroadcastInetEntry 2 } rlSntpBroadcastInetMode OBJECT-TYPE SYNTAX INTEGER { none(1), receive(2), send(3), receiveSend(4) } MAX-ACCESS read-write STATUS current DESCRIPTION "SNTP/NTP Broadcast Mode. none - no broadcast SNTP packets are received or sent. Receive - host only receive SNTP packets that were sent to broadcast address (were not directed to the host). This is multicast mode in the RFC. Send - host only send SNTP packets and wait for replies directed to the host. This is anycast mode in the RFC. ReceiveSend - host receive broadcast messages (destination is broadcast address in the received messages) and send SNTP packets to wait for replies directed to the host (destination address of the reply is the host address). This mode combines anycast and multicast modes in the RFC." DEFVAL { receiveSend } ::= { rlSntpBroadcastInetEntry 3 } rlSntpBroadcastInetPolled OBJECT-TYPE SYNTAX TruthValue MAX-ACCESS read-write STATUS current DESCRIPTION "TRUE if participating in polling cycle, else FALSE." DEFVAL { false } ::= { rlSntpBroadcastInetEntry 4 } rlSntpBroadcastInetAddressType OBJECT-TYPE SYNTAX InetAddressType MAX-ACCESS read-only STATUS current DESCRIPTION "Inet Address Type of a trusted SNTP server." ::= { rlSntpBroadcastInetEntry 5 } rlSntpBroadcastInetAddress OBJECT-TYPE SYNTAX InetAddress MAX-ACCESS read-only STATUS current DESCRIPTION "Inet Address of a trusted SNTP server." ::= { rlSntpBroadcastInetEntry 6 } rlSntpBroadcastInetStratum OBJECT-TYPE SYNTAX NTPStratum MAX-ACCESS read-only STATUS current DESCRIPTION "The stratum of this server." ::= { rlSntpBroadcastInetEntry 7 } rlSntpBroadcastInetLastResp OBJECT-TYPE SYNTAX NTPTimeStamp MAX-ACCESS read-only STATUS current DESCRIPTION "SNTP Broadcast Last Response Time" ::= { rlSntpBroadcastInetEntry 8 } rlSntpBroadcastInetStatus OBJECT-TYPE SYNTAX INTEGER { unknown(1), inProcess(2), up(3), down(4) } MAX-ACCESS read-only STATUS current DESCRIPTION "The Operational State of the remote IP Address of the SNTP Broadcast. unknown - requests were not sent yet. inProcess - replies were not received yet. up - server sent SNTP packets. down - server stopped sending SNTP packets." DEFVAL { unknown } ::= { rlSntpBroadcastInetEntry 9 } rlSntpBroadcastInetOffset OBJECT-TYPE SYNTAX NTPTimeStamp UNITS "seconds" MAX-ACCESS read-only STATUS current DESCRIPTION "The estimated offset of the server's clock relative to the local clock, in seconds. The host determines the value of this object using the algorithm described in RFC 2030." ::= { rlSntpBroadcastInetEntry 10 } rlSntpBroadcastInetDelay OBJECT-TYPE SYNTAX NTPSignedTimeValue UNITS "seconds" MAX-ACCESS read-only STATUS current DESCRIPTION "The estimated round-trip delay of the server's clock relative to the local clock over the network path between them, in seconds. The host determines the value of this object using the algorithm described in RFC 2030." ::= { rlSntpBroadcastInetEntry 11 } rlSntpBroadcastInetRowStatus OBJECT-TYPE SYNTAX RowStatus MAX-ACCESS read-write STATUS current DESCRIPTION "The Status of this SNTP broadcast interface information." ::= { rlSntpBroadcastInetEntry 12 } -- ---------------------------------------------------------------------- -- IPv6: Table for configuring Interfaces (Anycast) -- ---------------------------------------------------------------------- rlSntpConfigAnycastInetTable OBJECT-TYPE SYNTAX SEQUENCE OF RlSntpAnycastInetEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "A table containing anycast information per interface." ::= { rlSntpConfig 16 } rlSntpAnycastInetEntry OBJECT-TYPE SYNTAX RlSntpAnycastInetEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "Private paramters for interface: server info." INDEX { rlSntpAnycastInetIfIndex } ::= { rlSntpConfigAnycastInetTable 1 } RlSntpAnycastInetEntry ::= SEQUENCE { rlSntpAnycastInetIfIndex INTEGER, rlSntpAnycastInetAddressType InetAddressType, rlSntpAnycastInetAddress InetAddress, rlSntpAnycastInetStratum NTPStratum, rlSntpAnycastInetLastResp NTPTimeStamp, rlSntpAnycastInetStatus INTEGER, rlSntpAnycastInetOffset NTPTimeStamp, rlSntpAnycastInetDelay NTPSignedTimeValue, rlSntpAnycastInetRowStatus RowStatus } rlSntpAnycastInetIfIndex OBJECT-TYPE SYNTAX INTEGER MAX-ACCESS not-accessible STATUS current DESCRIPTION "The interface addressed by this entry." ::= {rlSntpAnycastInetEntry 1} rlSntpAnycastInetAddressType OBJECT-TYPE SYNTAX InetAddressType MAX-ACCESS read-only STATUS current DESCRIPTION "Inet Address Type of a trusted SNTP server." ::= { rlSntpAnycastInetEntry 2 } rlSntpAnycastInetAddress OBJECT-TYPE SYNTAX InetAddress MAX-ACCESS read-only STATUS current DESCRIPTION "Inet Address of a trusted SNTP server." ::= { rlSntpAnycastInetEntry 3 } rlSntpAnycastInetStratum OBJECT-TYPE SYNTAX NTPStratum MAX-ACCESS read-only STATUS current DESCRIPTION "The stratum of this server." ::= { rlSntpAnycastInetEntry 4 } rlSntpAnycastInetLastResp OBJECT-TYPE SYNTAX NTPTimeStamp MAX-ACCESS read-only STATUS current DESCRIPTION "SNTP Anycast Last Response Time" ::= { rlSntpAnycastInetEntry 5 } rlSntpAnycastInetStatus OBJECT-TYPE SYNTAX INTEGER { unknown(1), inProcess(2), up(3), down(4) } MAX-ACCESS read-only STATUS current DESCRIPTION "The Operational State of the remote IP Address of the SNTP Anycast. unknown - requests were not sent yet. inProcess - replies were not received yet. up - server sent SNTP packets. down - server stopped sending SNTP packets." DEFVAL { unknown } ::= { rlSntpAnycastInetEntry 6 } rlSntpAnycastInetOffset OBJECT-TYPE SYNTAX NTPTimeStamp UNITS "seconds" MAX-ACCESS read-only STATUS current DESCRIPTION "The estimated offset of the server's clock relative to the local clock, in seconds. The host determines the value of this object using the algorithm described in RFC 2030." ::= { rlSntpAnycastInetEntry 7 } rlSntpAnycastInetDelay OBJECT-TYPE SYNTAX NTPSignedTimeValue UNITS "seconds" MAX-ACCESS read-only STATUS current DESCRIPTION "The estimated round-trip delay of the server's clock relative to the local clock over the network path between them, in seconds. The host determines the value of this object using the algorithm described in RFC 2030." ::= { rlSntpAnycastInetEntry 8 } rlSntpAnycastInetRowStatus OBJECT-TYPE SYNTAX RowStatus MAX-ACCESS read-write STATUS current DESCRIPTION "The Status of this SNTP anycast interface information." ::= { rlSntpAnycastInetEntry 9 } -- ---------------------------------------------------------------------- -- IPv6: Table for configuring Servers (Unicast) -- ---------------------------------------------------------------------- rlSntpConfigServerInetTable OBJECT-TYPE SYNTAX SEQUENCE OF RlSntpServerInetEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "A table containing trusted SNTP servers to be queried in unicast or broadcast mode." ::= { rlSntpConfig 17 } rlSntpServerInetEntry OBJECT-TYPE SYNTAX RlSntpServerInetEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "A trusted server." INDEX { rlSntpServerInetAddressType, rlSntpServerInetAddress } ::= { rlSntpConfigServerInetTable 1 } RlSntpServerInetEntry ::= SEQUENCE { rlSntpServerInetAddressType InetAddressType, rlSntpServerInetAddress InetAddress, rlSntpServerInetPolled TruthValue, rlSntpServerInetStratum NTPStratum, rlSntpServerInetLastResp NTPTimeStamp, rlSntpServerInetStatus INTEGER, rlSntpServerInetOffset NTPTimeStamp, rlSntpServerInetDelay NTPSignedTimeValue, rlSntpServerInetKeyIdentifier Unsigned32, rlSntpServerInetRowStatus RowStatus } rlSntpServerInetAddressType OBJECT-TYPE SYNTAX InetAddressType MAX-ACCESS not-accessible STATUS current DESCRIPTION "Inet Address Type of a trusted SNTP server." ::= { rlSntpServerInetEntry 1 } rlSntpServerInetAddress OBJECT-TYPE SYNTAX InetAddress MAX-ACCESS not-accessible STATUS current DESCRIPTION "Inet Address of a trusted SNTP server." ::= { rlSntpServerInetEntry 2 } rlSntpServerInetPolled OBJECT-TYPE SYNTAX TruthValue MAX-ACCESS read-write STATUS current DESCRIPTION "TRUE if participating in polling cycle, else FALSE." DEFVAL { false } ::= { rlSntpServerInetEntry 3 } rlSntpServerInetStratum OBJECT-TYPE SYNTAX NTPStratum MAX-ACCESS read-only STATUS current DESCRIPTION "The stratum of this server." ::= { rlSntpServerInetEntry 4 } rlSntpServerInetLastResp OBJECT-TYPE SYNTAX NTPTimeStamp MAX-ACCESS read-only STATUS current DESCRIPTION "SNTP Server Last Response Time" ::= { rlSntpServerInetEntry 5 } rlSntpServerInetStatus OBJECT-TYPE SYNTAX INTEGER { unknown(1), inProcess(2), up(3), down(4) } MAX-ACCESS read-only STATUS current DESCRIPTION "The Operational State of the remote IP Address of the SNTP Server. unknown - requests were not sent yet. inProcess - replies were not received yet. up - server sent SNTP packets. down - server stopped sending SNTP packets." DEFVAL { unknown } ::= { rlSntpServerInetEntry 6 } rlSntpServerInetOffset OBJECT-TYPE SYNTAX NTPTimeStamp UNITS "seconds" MAX-ACCESS read-only STATUS current DESCRIPTION "The estimated offset of the server's clock relative to the local clock, in seconds. The host determines the value of this object using the algorithm described in RFC 2030." ::= { rlSntpServerInetEntry 7 } rlSntpServerInetDelay OBJECT-TYPE SYNTAX NTPSignedTimeValue UNITS "seconds" MAX-ACCESS read-only STATUS current DESCRIPTION "The estimated round-trip delay of the server's clock relative to the local clock over the network path between them, in seconds. The host determines the value of this object using the algorithm described in RFC 2030." ::= { rlSntpServerInetEntry 8 } rlSntpServerInetKeyIdentifier OBJECT-TYPE SYNTAX Unsigned32 MAX-ACCESS read-write STATUS current DESCRIPTION "Authentication key identifier. The valid range is 1-4294967295. Value zero, means no authentication is being done." ::= { rlSntpServerInetEntry 9 } rlSntpServerInetRowStatus OBJECT-TYPE SYNTAX RowStatus MAX-ACCESS read-write STATUS current DESCRIPTION "The Status of this SNTP server information." ::= { rlSntpServerInetEntry 10 } rlSntpAllServerInetTable OBJECT-TYPE SYNTAX SEQUENCE OF RlSntpAllServerInetEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "A table containing all SNTP servers (for example: statically configured, dynamically configured) to be queried in unicast or broadcast mode." ::= { rlSntpConfig 18 } rlSntpAllServerInetEntry OBJECT-TYPE SYNTAX RlSntpAllServerInetEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "A server entry." INDEX { rlSntpAllServerSource, rlSntpAllServerIfIndex, rlSntpAllServerPreference, rlSntpAllServerInetAddressType, rlSntpAllServerInetAddress } ::= { rlSntpAllServerInetTable 1 } RlSntpAllServerInetEntry ::= SEQUENCE { rlSntpAllServerSource INTEGER, rlSntpAllServerIfIndex InterfaceIndex, rlSntpAllServerPreference INTEGER, rlSntpAllServerInetAddressType InetAddressType, rlSntpAllServerInetAddress InetAddress, rlSntpAllServerInetPolled TruthValue, rlSntpAllServerInetStratum NTPStratum, rlSntpAllServerInetLastResp NTPTimeStamp, rlSntpAllServerInetStatus INTEGER, rlSntpAllServerInetOffset NTPTimeStamp, rlSntpAllServerInetDelay NTPSignedTimeValue, rlSntpAllServerInetKeyIdentifier Unsigned32 } rlSntpAllServerSource OBJECT-TYPE SYNTAX INTEGER { static(1), dhcpv6(2) } MAX-ACCESS not-accessible STATUS current DESCRIPTION "The SNTP server source: static means manually defined, dhcpv6 means learnt from DHCP. Only static entries are stored in CDB." ::= { rlSntpAllServerInetEntry 1 } rlSntpAllServerIfIndex OBJECT-TYPE SYNTAX InterfaceIndex MAX-ACCESS not-accessible STATUS current DESCRIPTION "The ifIndex from which the SNTP server configuration was received (for dhcpv6 configurations). For static entries the value of this field will always be 1. " ::= { rlSntpAllServerInetEntry 2 } rlSntpAllServerPreference OBJECT-TYPE SYNTAX INTEGER MAX-ACCESS not-accessible STATUS current DESCRIPTION "The preference of SNTP server (for dhcpv6 configurations). For static entries the value of this field will always be 0. " ::= { rlSntpAllServerInetEntry 3 } rlSntpAllServerInetAddressType OBJECT-TYPE SYNTAX InetAddressType MAX-ACCESS not-accessible STATUS current DESCRIPTION "SNTP server inet address type." ::= { rlSntpAllServerInetEntry 4 } rlSntpAllServerInetAddress OBJECT-TYPE SYNTAX InetAddress MAX-ACCESS not-accessible STATUS current DESCRIPTION "SNTP server inet address." ::= { rlSntpAllServerInetEntry 5 } rlSntpAllServerInetPolled OBJECT-TYPE SYNTAX TruthValue MAX-ACCESS read-only STATUS current DESCRIPTION "TRUE if participating in polling cycle, else FALSE." DEFVAL { false } ::= { rlSntpAllServerInetEntry 6 } rlSntpAllServerInetStratum OBJECT-TYPE SYNTAX NTPStratum MAX-ACCESS read-only STATUS current DESCRIPTION "The stratum of this server." ::= { rlSntpAllServerInetEntry 7 } rlSntpAllServerInetLastResp OBJECT-TYPE SYNTAX NTPTimeStamp MAX-ACCESS read-only STATUS current DESCRIPTION "SNTP Server Last Response Time" ::= { rlSntpAllServerInetEntry 8 } rlSntpAllServerInetStatus OBJECT-TYPE SYNTAX INTEGER { unknown(1), inProcess(2), up(3), down(4) } MAX-ACCESS read-only STATUS current DESCRIPTION "The Operational State of the remote IP Address of the SNTP Server. unknown - requests were not sent yet. inProcess - replies were not received yet. up - server sent SNTP packets. down - server stopped sending SNTP packets." DEFVAL { unknown } ::= { rlSntpAllServerInetEntry 9 } rlSntpAllServerInetOffset OBJECT-TYPE SYNTAX NTPTimeStamp UNITS "seconds" MAX-ACCESS read-only STATUS current DESCRIPTION "The estimated offset of the server's clock relative to the local clock, in seconds. The host determines the value of this object using the algorithm described in RFC 2030." ::= { rlSntpAllServerInetEntry 10 } rlSntpAllServerInetDelay OBJECT-TYPE SYNTAX NTPSignedTimeValue UNITS "seconds" MAX-ACCESS read-only STATUS current DESCRIPTION "The estimated round-trip delay of the server's clock relative to the local clock over the network path between them, in seconds. The host determines the value of this object using the algorithm described in RFC 2030." ::= { rlSntpAllServerInetEntry 11 } rlSntpAllServerInetKeyIdentifier OBJECT-TYPE SYNTAX Unsigned32 MAX-ACCESS read-write STATUS current DESCRIPTION "Authentication key identifier. The valid range is 1-4294967295. Value zero, means no authentication is being done." ::= { rlSntpAllServerInetEntry 12 } END