-- ***************************************************************** -- CISCO-SESS-BORDER-CTRLR-CALL-STATS-MIB.my -- -- Copyright (c) 2007-2008, 2010 by cisco Systems Inc. -- All rights reserved. -- -- ***************************************************************** CISCO-SESS-BORDER-CTRLR-CALL-STATS-MIB DEFINITIONS ::= BEGIN IMPORTS MODULE-IDENTITY, OBJECT-TYPE, Integer32, Counter64, Gauge32, Counter32, Unsigned32 FROM SNMPv2-SMI MODULE-COMPLIANCE, OBJECT-GROUP FROM SNMPv2-CONF SnmpAdminString FROM SNMP-FRAMEWORK-MIB TEXTUAL-CONVENTION FROM SNMPv2-TC EntPhysicalIndexOrZero FROM CISCO-TC ciscoMgmt FROM CISCO-SMI; ciscoSbcCallStatsMIB MODULE-IDENTITY LAST-UPDATED "201009030000Z" ORGANIZATION "Cisco Systems, Inc." CONTACT-INFO "Cisco Systems Customer Service Postal: 170 W Tasman Drive San Jose, CA 95134 USA Tel: +1 800 553-NETS E-mail: sbc-dev@cisco.com" DESCRIPTION "The main purpose of this MIB is to define the statistics information for Session Border Controller application. The statistics are mainly of two types - Call statistics and Media statistics. The calls can further be categorized as SIP calls and H.248 calls. This MIB categorizes the statistics information into following four types: 1. Global call statistics - Represents the global call related statistics like call rates, media flows, signaling flows etc. 2. Periodic statistics - Represents the SBC call statistics information for a particular time interval like current 5 minutes, previous 5 minutes, current 15 minutes, previous 15 minutes, current hour and previous hour. 3. Per flow statistics - Represents the SBC media flow statistics. These are media statistics for each of the current ongoing call flow. 4. H.248 statistics - Represents the H.248 call related statistics information when H.248 controller is associated with SBC. The Session Border Controller (SBC) enables direct IP-to-IP interconnect between multiple administrative domains for session-based services providing protocol inter-working, security, and admission control and management. The SBC is a voice over IP (VoIP) device that sits on the border of a network and controls call admission to that network. The primary purpose of an SBC is to protect the interior of the network from excessive call load and malicious traffic. Additional functions provided by the SBC include media bridging and billing services. GLOSSARY SBC: Session Border Controller CSB: CISCO Session Border Controller CAC: Call Admission Control - protects voice traffic from the negative effects of other voice traffic and to keep excess voice traffic off the network. It is used to prevent congestion in Voice traffic. It is used in the Call Setup phase. RTP: Real Time Transport Protocol - defines a standardized packet format for delivering audio and video over the Internet. RTCP: Real Time Control Protocol - It is a sister protocol of the Real-time Transport Protocol (RTP). RTCP provides out-of-band control information for an RTP flow. It partners RTP in the delivery and packaging of multimedia data, but does not transport any data itself. It is used periodically to transmit control packets to participants in a streaming multimedia session. VMG: Virtual Media Gateway - introduced to bridge between different transmission technologies and to add service to end-user connections. Its architecture separates control and connectivity functions into physically separate network layers. VPN: Virtual Private Network - It is a communications network tunneled through another network, and dedicated for a specific network. Gate Id - Context Identifiers assigned uniquely to a SIP/H.248 call flows. Flow Pair Id: Stream Identifiers assigned uniquely to a SIP/H.248 call flows. Adjacency: An adjacency contains the system information to be transmitted to next HOP. REFERENCES 1. CISCO Session Border Controller Documents and FAQ http://zed.cisco.com/confluence/display/SBC/SBC" REVISION "201009030000Z" DESCRIPTION "Updated existing tables by adding new fields. Below is the description of changes for each table- 1. The statistics fields introduced in csbCallStatsTable are - csbCallStatsAvailableTranscodeFlows csbCallStatsActiveTranscodeFlows csbCallStatsPeakTranscodeFlows csbCallStatsTotalTranscodeFlows 2. The statistics fields introduced in csbCurrPeriodicStatsTable are - csbCurrPeriodicStatsTranscodedCalls csbCurrPeriodicStatsTransratedCalls csbCurrPeriodicStatsTotalCallUpdateFailure csbCurrPeriodicStatsActiveIpv6Calls csbCurrPeriodicStatsActiveE2EmergencyCalls csbCurrPeriodicStatsImsRxActiveCalls csbCurrPeriodicStatsImsRxCallSetupFaiures csbCurrPeriodicStatsImsRxCallRenagotiationAttempts csbCurrPeriodicStatsImsRxCallRenagotiationFailures csbCurrPeriodicStatsAudioTranscodedCalls csbCurrPeriodicStatsFaxTranscodedCalls csbCurrPeriodicStatsRtpDisallowedFailures csbCurrPeriodicStatsSrtpDisallowedFailures csbCurrPeriodicStatsNonSrtpCalls csbCurrPeriodicStatsSrtpNonIwCalls csbCurrPeriodicStatsSrtpIwCalls csbCurrPeriodicStatsDtmfIw2833Calls csbCurrPeriodicStatsDtmfIwInbandCalls csbCurrPeriodicStatsDtmfIw2833InbandCalls csbCurrPeriodicStatsTotalTapsRequested csbCurrPeriodicStatsTotalTapsSucceeded csbCurrPeriodicStatsCurrentTaps 3. The statistics fields introduced in csbHistoryStatsTable are- csbHistoryStatsTranscodedCalls csbHistoryStatsTransratedCalls csbHistoryStatsTotalCallUpdateFailure csbHistoryStatsActiveIpv6Calls csbHistoryStatsActiveE2EmergencyCalls csbHistoryStatsImsRxActiveCalls csbHistoryStatsImsRxCallSetupFaiures csbHistoryStatsImsRxCallRenagotiationAttempts csbHistoryStatsImsRxCallRenagotiationFailures csbHistoryStatsAudioTranscodedCalls csbHistoryStatsFaxTranscodedCalls csbHistoryStatsRtpDisallowedFailures csbHistoryStatsSrtpDisallowedFailures csbHistoryStatsNonSrtpCalls csbHistoryStatsSrtpNonIwCalls csbHistoryStatsSrtpIwCalls csbHistoryStatsDtmfIw2833Calls csbHistoryStatsDtmfIwInbandCalls csbHistoryStatsDtmfIw2833InbandCalls csbHistoryStatsTotalTapsRequested csbHistoryStatsTotalTapsSucceeded csbHistoryStatsCurrentTaps 4. The statistics field introduced in csbPerFlowStatsTable is- csbPerFlowStatsRTPPktsLost" REVISION "200808270000Z" DESCRIPTION "Updated description for following objects csbPerFlowStatsRTCPPktsSent csbPerFlowStatsRTCPPktsRcvd csbPerFlowStatsRTCPPktsLost Deprecated the csbH248StatsTable and replaced it with csbH248StatsRev1Table to correct problem with index." REVISION "200805290000Z" DESCRIPTION "Initial version of the MIB module." ::= { ciscoMgmt 657 } CiscoSbcPeriodicStatsInterval ::= TEXTUAL-CONVENTION STATUS current DESCRIPTION "This textual convention represents the interval values for which the periodic stats and history stats are to be displayed. fiveMinute - Interval to display current/previous 5 minutes statistics information. fifteenMinute - Interval to display current/previous 15 minutes statistics information. oneHour - Interval to display current/previous one hour statistics information. oneDay - Interval to display current/previous one day statistics information." SYNTAX INTEGER { fiveMinute(1), fifteenMinute(2), oneHour(3), oneDay(4) } ciscoSbcCallStatsMIBNotifs OBJECT IDENTIFIER ::= { ciscoSbcCallStatsMIB 0 } ciscoSbcCallStatsMIBObjects OBJECT IDENTIFIER ::= { ciscoSbcCallStatsMIB 1 } ciscoSbcCallStatsMIBConform OBJECT IDENTIFIER ::= { ciscoSbcCallStatsMIB 2 } csbCallStatsInstanceTable OBJECT-TYPE SYNTAX SEQUENCE OF CsbCallStatsInstanceEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "The call stats instance table contains the physical index for each of the physical entity (line card, primary, secondary cards). The index of the table is instance index which uniquely identifies the physical entity present on the box." ::= { ciscoSbcCallStatsMIBObjects 1 } csbCallStatsInstanceEntry OBJECT-TYPE SYNTAX CsbCallStatsInstanceEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "A conceptual row in csbCallStatsInstanceTable. There is an entry in this table for each SBC instance, as identified by a value of csbCallStatsInstanceIndex." INDEX { csbCallStatsInstanceIndex } ::= { csbCallStatsInstanceTable 1 } CsbCallStatsInstanceEntry ::= SEQUENCE { csbCallStatsInstanceIndex Unsigned32, csbCallStatsInstancePhysicalIndex EntPhysicalIndexOrZero } csbCallStatsInstanceIndex OBJECT-TYPE SYNTAX Unsigned32 MAX-ACCESS not-accessible STATUS current DESCRIPTION "This object uniquely identifies the sequence number of an entity or slot that is configured per device. This index is assigned arbitrarily by the engine and is not saved over reboots." ::= { csbCallStatsInstanceEntry 1 } csbCallStatsInstancePhysicalIndex OBJECT-TYPE SYNTAX EntPhysicalIndexOrZero MAX-ACCESS read-only STATUS current DESCRIPTION "This object indicates the physical entity for which all the measurements are maintained. The exact type of this entity is described by its entPhysicalVendorType value." ::= { csbCallStatsInstanceEntry 2 } csbCallStatsTable OBJECT-TYPE SYNTAX SEQUENCE OF CsbCallStatsEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "This table describes the global statistics information in the form of a table which contains call specific information like call rates, media flows, signaling flows etc. The index of the table is service index which corresponds to a particular service configured on the SBC and all the rows of the table represents the global information regarding all the call flows related to that particular service. The other index of this table is csbCallStatsInstanceIndex which is defined in csbCallStatsInstanceTable." ::= { ciscoSbcCallStatsMIBObjects 2 } csbCallStatsEntry OBJECT-TYPE SYNTAX CsbCallStatsEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "An conceptual row in the csbCallStatsGlobalStatsTable. There is an entry in this table for the particular service configured on SBC identified by a value of csbCallStatsInstanceIndex. The other index of this table is csbCallStatsInstanceIndex which is defined in csbCallStatsInstanceTable." INDEX { csbCallStatsInstanceIndex, csbCallStatsServiceIndex } ::= { csbCallStatsTable 1 } CsbCallStatsEntry ::= SEQUENCE { csbCallStatsServiceIndex Unsigned32, csbCallStatsSbcName SnmpAdminString, csbCallStatsCallsHigh Unsigned32, csbCallStatsRate1Sec Gauge32, csbCallStatsCallsLow Unsigned32, csbCallStatsAvailableFlows Gauge32, csbCallStatsUsedFlows Gauge32, csbCallStatsPeakFlows Unsigned32, csbCallStatsTotalFlows Unsigned32, csbCallStatsUsedSigFlows Gauge32, csbCallStatsPeakSigFlows Unsigned32, csbCallStatsTotalSigFlows Unsigned32, csbCallStatsAvailablePktRate Gauge32, csbCallStatsUnclassifiedPkts Counter64, csbCallStatsRTPPktsSent Counter64, csbCallStatsRTPPktsRcvd Counter64, csbCallStatsRTPPktsDiscard Counter64, csbCallStatsRTPOctetsSent Counter64, csbCallStatsRTPOctetsRcvd Counter64, csbCallStatsRTPOctetsDiscard Counter64, csbCallStatsNoMediaCount Counter32, csbCallStatsRouteErrors Counter32, csbCallStatsAvailableTranscodeFlows Gauge32, csbCallStatsActiveTranscodeFlows Gauge32, csbCallStatsPeakTranscodeFlows Unsigned32, csbCallStatsTotalTranscodeFlows Unsigned32 } csbCallStatsServiceIndex OBJECT-TYPE SYNTAX Unsigned32 MAX-ACCESS not-accessible STATUS current DESCRIPTION "This object identifies the index of the name of the SBC service configured. This object also acts as an index for the table." ::= { csbCallStatsEntry 1 } csbCallStatsSbcName OBJECT-TYPE SYNTAX SnmpAdminString MAX-ACCESS read-only STATUS current DESCRIPTION "This object indicates the configured name of the SBC service. The length of this object is zero when value is not assigned to it." ::= { csbCallStatsEntry 2 } csbCallStatsCallsHigh OBJECT-TYPE SYNTAX Unsigned32 UNITS "calls per second" MAX-ACCESS read-only STATUS current DESCRIPTION "This object indicates the maximum number of calls per second processed by the Session Border Controller in past 24 hours." ::= { csbCallStatsEntry 3 } csbCallStatsRate1Sec OBJECT-TYPE SYNTAX Gauge32 UNITS "calls per second" MAX-ACCESS read-only STATUS current DESCRIPTION "This object indicates the average calls per second processed by the Session Border Controller." ::= { csbCallStatsEntry 4 } csbCallStatsCallsLow OBJECT-TYPE SYNTAX Unsigned32 UNITS "calls per second" MAX-ACCESS read-only STATUS current DESCRIPTION "This object indicates the minimum calls per second in past 24 hours." ::= { csbCallStatsEntry 5 } csbCallStatsAvailableFlows OBJECT-TYPE SYNTAX Gauge32 UNITS "flows" MAX-ACCESS read-only STATUS current DESCRIPTION "This object indicates the number of media flows which are available." ::= { csbCallStatsEntry 6 } csbCallStatsUsedFlows OBJECT-TYPE SYNTAX Gauge32 UNITS "flows" MAX-ACCESS read-only STATUS current DESCRIPTION "This object indicates the number of media flows which are used. This is for the flow allocated and connected. The flow allocated but not connected is not counted." ::= { csbCallStatsEntry 7 } csbCallStatsPeakFlows OBJECT-TYPE SYNTAX Unsigned32 UNITS "flows" MAX-ACCESS read-only STATUS current DESCRIPTION "This object indicates the number of peak flows in SBC. This is the highest recorded value for the active flows since the box was booted/reseted." ::= { csbCallStatsEntry 8 } csbCallStatsTotalFlows OBJECT-TYPE SYNTAX Unsigned32 UNITS "flows" MAX-ACCESS read-only STATUS current DESCRIPTION "This object indicates the total number of media support by this instance of SBC. The total number of flows include the available flows and the active flows. This value is since box was booted/reseted. Total flows include the active flows and the flows allocated but not connected." ::= { csbCallStatsEntry 9 } csbCallStatsUsedSigFlows OBJECT-TYPE SYNTAX Gauge32 UNITS "signal flows" MAX-ACCESS read-only STATUS current DESCRIPTION "This object indicates the number of active signaling flows for signaling pinholes." ::= { csbCallStatsEntry 10 } csbCallStatsPeakSigFlows OBJECT-TYPE SYNTAX Unsigned32 UNITS "signal flows" MAX-ACCESS read-only STATUS current DESCRIPTION "This object indicates the peak signaling flow in SBC. This is the highest recorded value for the active signaling flows. This object is calculated using csbCallStatsUsedFlows." ::= { csbCallStatsEntry 11 } csbCallStatsTotalSigFlows OBJECT-TYPE SYNTAX Unsigned32 UNITS "signal flows" MAX-ACCESS read-only STATUS current DESCRIPTION "This object indicates the maximum number of Signalling Flows that can be supported by this instance of SBC." ::= { csbCallStatsEntry 12 } csbCallStatsAvailablePktRate OBJECT-TYPE SYNTAX Gauge32 UNITS "packets per second" MAX-ACCESS read-only STATUS current DESCRIPTION "This object indicates the remaining capacity that can be supported by SBC." ::= { csbCallStatsEntry 13 } csbCallStatsUnclassifiedPkts OBJECT-TYPE SYNTAX Counter64 UNITS "packets" MAX-ACCESS read-only STATUS current DESCRIPTION "This object indicates the number of unclassified packets processed by SBC." ::= { csbCallStatsEntry 14 } csbCallStatsRTPPktsSent OBJECT-TYPE SYNTAX Counter64 UNITS "packets" MAX-ACCESS read-only STATUS current DESCRIPTION "This object indicates the total number of RTP packets sent." ::= { csbCallStatsEntry 15 } csbCallStatsRTPPktsRcvd OBJECT-TYPE SYNTAX Counter64 UNITS "packets" MAX-ACCESS read-only STATUS current DESCRIPTION "This object indicates the total number of RTP packets received." ::= { csbCallStatsEntry 16 } csbCallStatsRTPPktsDiscard OBJECT-TYPE SYNTAX Counter64 UNITS "packets" MAX-ACCESS read-only STATUS current DESCRIPTION "This object indicates the total number of RTP packets discarded." ::= { csbCallStatsEntry 17 } csbCallStatsRTPOctetsSent OBJECT-TYPE SYNTAX Counter64 UNITS "octets" MAX-ACCESS read-only STATUS current DESCRIPTION "This object indicates the number of RTP octets sent by the SBC." ::= { csbCallStatsEntry 18 } csbCallStatsRTPOctetsRcvd OBJECT-TYPE SYNTAX Counter64 UNITS "octets" MAX-ACCESS read-only STATUS current DESCRIPTION "This object indicates the number of RTP octets received by the SBC." ::= { csbCallStatsEntry 19 } csbCallStatsRTPOctetsDiscard OBJECT-TYPE SYNTAX Counter64 UNITS "octets" MAX-ACCESS read-only STATUS current DESCRIPTION "This object indicates the number of RTP octets discarded by the SBC." ::= { csbCallStatsEntry 20 } csbCallStatsNoMediaCount OBJECT-TYPE SYNTAX Counter32 UNITS "no media events" MAX-ACCESS read-only STATUS current DESCRIPTION "This object indicates the accumulated No media event count." ::= { csbCallStatsEntry 21 } csbCallStatsRouteErrors OBJECT-TYPE SYNTAX Counter32 UNITS "route error events" MAX-ACCESS read-only STATUS current DESCRIPTION "This object indicates the accumulated route error event count. This counter is for the route error of media stream." ::= { csbCallStatsEntry 22 } csbCallStatsAvailableTranscodeFlows OBJECT-TYPE SYNTAX Gauge32 UNITS "flows" MAX-ACCESS read-only STATUS current DESCRIPTION "This object indicates the number of additional transcoded flows that this media gateway manager (MGM) entity is currently able to configure." ::= { csbCallStatsEntry 23 } csbCallStatsActiveTranscodeFlows OBJECT-TYPE SYNTAX Gauge32 UNITS "flows" MAX-ACCESS read-only STATUS current DESCRIPTION "This object indicates the current number of transcoded flows that are actively forwarding media traffic. In this context, a flow is a media stream passing through the device. So a single voice call will be counted only once." ::= { csbCallStatsEntry 24 } csbCallStatsPeakTranscodeFlows OBJECT-TYPE SYNTAX Unsigned32 UNITS "flows" MAX-ACCESS read-only STATUS current DESCRIPTION "This object indicates the peak number of active transcoded flows since the statistics were last reset. In this context, a flow is a media stream passing through the device, so a single voice call will be counted once." ::= { csbCallStatsEntry 25 } csbCallStatsTotalTranscodeFlows OBJECT-TYPE SYNTAX Unsigned32 UNITS "flows" MAX-ACCESS read-only STATUS current DESCRIPTION "This object indicates the accumulated total number of transcoded flows. This count contains both active flows and flows that were allocated but never connected. In this context, a flow is a media stream passing through the device, so a single voice call will be counted once." ::= { csbCallStatsEntry 26 } csbCurrPeriodicStatsTable OBJECT-TYPE SYNTAX SEQUENCE OF CsbCurrPeriodicStatsEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "This table is used to collect measurement over several different intervals as defined by the csbCurrPeriodicStatsInterval object. When a new interval starts the objects associated with the interval are reset and count up throughout the interval. The index of the table is the interval for which the stats information is to be displayed. The interval values can be 5 min, 15 mins, 1 hour and one day. The other indices of this table are csbCallStatsInstanceIndex defined in csbCallStatsInstanceTable and csbCallStatsServiceIndex defined in csbCallStatsTable. The gauge values are reported as :- 1.If the period being queried is current5mins, this is the value at the instant that the query is issued. 2.Otherwise, for the other intevals, this is an average value during the summary period sampled at 5 minute intervals." ::= { ciscoSbcCallStatsMIBObjects 3 } csbCurrPeriodicStatsEntry OBJECT-TYPE SYNTAX CsbCurrPeriodicStatsEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "An conceptual row in the csbCurrPeriodicStatsTable. There is an entry in this table for the particular controller by a value of csbH248StatsCtrlrIndex. The other indices of this table are csbCallStatsInstanceIndex defined in csbCallStatsInstanceTable and csbCallStatsServiceIndex defined in csbCallStatsTable." INDEX { csbCallStatsInstanceIndex, csbCallStatsServiceIndex, csbCurrPeriodicStatsInterval } ::= { csbCurrPeriodicStatsTable 1 } CsbCurrPeriodicStatsEntry ::= SEQUENCE { csbCurrPeriodicStatsInterval CiscoSbcPeriodicStatsInterval, csbCurrPeriodicStatsActiveCalls Gauge32, csbCurrPeriodicStatsActivatingCalls Gauge32, csbCurrPeriodicStatsDeactivatingCalls Gauge32, csbCurrPeriodicStatsTotalCallAttempts Gauge32, csbCurrPeriodicStatsFailedCallAttempts Gauge32, csbCurrPeriodicStatsCallRoutingFailure Gauge32, csbCurrPeriodicStatsCallResourceFailure Gauge32, csbCurrPeriodicStatsCallMediaFailure Gauge32, csbCurrPeriodicStatsCallSigFailure Gauge32, csbCurrPeriodicStatsActiveCallFailure Gauge32, csbCurrPeriodicStatsCongestionFailure Gauge32, csbCurrPeriodicStatsCallSetupPolicyFailure Gauge32, csbCurrPeriodicStatsCallSetupNAPolicyFailure Gauge32, csbCurrPeriodicStatsCallSetupRoutingPolicyFailure Gauge32, csbCurrPeriodicStatsCallSetupCACPolicyFailure Gauge32, csbCurrPeriodicStatsCallSetupCACCallLimitFailure Gauge32, csbCurrPeriodicStatsCallSetupCACRateLimitFailure Gauge32, csbCurrPeriodicStatsCallSetupCACBandwidthFailure Gauge32, csbCurrPeriodicStatsCallSetupCACMediaLimitFailure Gauge32, csbCurrPeriodicStatsCallSetupCACMediaUpdateFailure Gauge32, csbCurrPeriodicStatsTimestamp OCTET STRING, csbCurrPeriodicStatsTranscodedCalls Gauge32, csbCurrPeriodicStatsTransratedCalls Gauge32, csbCurrPeriodicStatsTotalCallUpdateFailure Gauge32, csbCurrPeriodicStatsActiveIpv6Calls Gauge32, csbCurrPeriodicStatsActiveEmergencyCalls Gauge32, csbCurrPeriodicStatsActiveE2EmergencyCalls Gauge32, csbCurrPeriodicStatsImsRxActiveCalls Gauge32, csbCurrPeriodicStatsImsRxCallSetupFaiures Gauge32, csbCurrPeriodicStatsImsRxCallRenegotiationAttempts Gauge32, csbCurrPeriodicStatsImsRxCallRenegotiationFailures Gauge32, csbCurrPeriodicStatsAudioTranscodedCalls Gauge32, csbCurrPeriodicStatsFaxTranscodedCalls Gauge32, csbCurrPeriodicStatsRtpDisallowedFailures Gauge32, csbCurrPeriodicStatsSrtpDisallowedFailures Gauge32, csbCurrPeriodicStatsNonSrtpCalls Gauge32, csbCurrPeriodicStatsSrtpNonIwCalls Gauge32, csbCurrPeriodicStatsSrtpIwCalls Gauge32, csbCurrPeriodicStatsDtmfIw2833Calls Gauge32, csbCurrPeriodicStatsDtmfIwInbandCalls Gauge32, csbCurrPeriodicStatsDtmfIw2833InbandCalls Gauge32, csbCurrPeriodicStatsTotalTapsRequested Gauge32, csbCurrPeriodicStatsTotalTapsSucceeded Gauge32, csbCurrPeriodicStatsCurrentTaps Gauge32, csbCurrPeriodicIpsecCalls Gauge32 } csbCurrPeriodicStatsInterval OBJECT-TYPE SYNTAX CiscoSbcPeriodicStatsInterval MAX-ACCESS not-accessible STATUS current DESCRIPTION "This object identifies the interval for which the periodic statistics information is to be displayed. The interval values can be 5 min, 15 mins, 1 hour , 1 Day. This object acts as index for the table." ::= { csbCurrPeriodicStatsEntry 1 } csbCurrPeriodicStatsActiveCalls OBJECT-TYPE SYNTAX Gauge32 UNITS "calls" MAX-ACCESS read-only STATUS current DESCRIPTION "This object indicates the number of calls that have become active during this interval." ::= { csbCurrPeriodicStatsEntry 2 } csbCurrPeriodicStatsActivatingCalls OBJECT-TYPE SYNTAX Gauge32 UNITS "calls" MAX-ACCESS read-only STATUS current DESCRIPTION "This object indicates the number of calls that have become activing during this interval." ::= { csbCurrPeriodicStatsEntry 3 } csbCurrPeriodicStatsDeactivatingCalls OBJECT-TYPE SYNTAX Gauge32 UNITS "calls" MAX-ACCESS read-only STATUS current DESCRIPTION "This object indicates the number of calls that have become deactiving during this interval." ::= { csbCurrPeriodicStatsEntry 4 } csbCurrPeriodicStatsTotalCallAttempts OBJECT-TYPE SYNTAX Gauge32 MAX-ACCESS read-only STATUS current DESCRIPTION "This object indicates the number of total call attempts during this interval." ::= { csbCurrPeriodicStatsEntry 5 } csbCurrPeriodicStatsFailedCallAttempts OBJECT-TYPE SYNTAX Gauge32 MAX-ACCESS read-only STATUS current DESCRIPTION "This object indicates the number of failed call attempts during this interval." ::= { csbCurrPeriodicStatsEntry 6 } csbCurrPeriodicStatsCallRoutingFailure OBJECT-TYPE SYNTAX Gauge32 MAX-ACCESS read-only STATUS current DESCRIPTION "This object indicates the number of call setup failures due to routing failures during this interval." ::= { csbCurrPeriodicStatsEntry 7 } csbCurrPeriodicStatsCallResourceFailure OBJECT-TYPE SYNTAX Gauge32 MAX-ACCESS read-only STATUS current DESCRIPTION "This object indicates the number of call setup failures due to resource failures during this interval." ::= { csbCurrPeriodicStatsEntry 8 } csbCurrPeriodicStatsCallMediaFailure OBJECT-TYPE SYNTAX Gauge32 MAX-ACCESS read-only STATUS current DESCRIPTION "This object indicates the number of call setup failures due to media failure during this interval." ::= { csbCurrPeriodicStatsEntry 9 } csbCurrPeriodicStatsCallSigFailure OBJECT-TYPE SYNTAX Gauge32 MAX-ACCESS read-only STATUS current DESCRIPTION "This object indicates the number of call setup failures due to signaling failure during this interval." ::= { csbCurrPeriodicStatsEntry 10 } csbCurrPeriodicStatsActiveCallFailure OBJECT-TYPE SYNTAX Gauge32 MAX-ACCESS read-only STATUS current DESCRIPTION "This object indicates the number of active call failures during this interval." ::= { csbCurrPeriodicStatsEntry 11 } csbCurrPeriodicStatsCongestionFailure OBJECT-TYPE SYNTAX Gauge32 MAX-ACCESS read-only STATUS current DESCRIPTION "This object indicates the number of call setup failures due to congestion during this interval." ::= { csbCurrPeriodicStatsEntry 12 } csbCurrPeriodicStatsCallSetupPolicyFailure OBJECT-TYPE SYNTAX Gauge32 MAX-ACCESS read-only STATUS current DESCRIPTION "This object indicates the number of call setup failures due to policy failure during this interval." ::= { csbCurrPeriodicStatsEntry 13 } csbCurrPeriodicStatsCallSetupNAPolicyFailure OBJECT-TYPE SYNTAX Gauge32 MAX-ACCESS read-only STATUS current DESCRIPTION "This object indicates the number of call setup failures due to NA policy failure during this interval." ::= { csbCurrPeriodicStatsEntry 14 } csbCurrPeriodicStatsCallSetupRoutingPolicyFailure OBJECT-TYPE SYNTAX Gauge32 MAX-ACCESS read-only STATUS current DESCRIPTION "This object indicates the number of call setup failures due to routing policy failure during this interval." ::= { csbCurrPeriodicStatsEntry 15 } csbCurrPeriodicStatsCallSetupCACPolicyFailure OBJECT-TYPE SYNTAX Gauge32 MAX-ACCESS read-only STATUS current DESCRIPTION "This object indicates the number of call setup failures due to CAC policy failure during this interval." ::= { csbCurrPeriodicStatsEntry 16 } csbCurrPeriodicStatsCallSetupCACCallLimitFailure OBJECT-TYPE SYNTAX Gauge32 MAX-ACCESS read-only STATUS current DESCRIPTION "This object indicates the number of call setup failures due to CAC call limit during this interval." ::= { csbCurrPeriodicStatsEntry 17 } csbCurrPeriodicStatsCallSetupCACRateLimitFailure OBJECT-TYPE SYNTAX Gauge32 MAX-ACCESS read-only STATUS current DESCRIPTION "This object indicates the number of call setup failures due to CAC call rate limit during this interval." ::= { csbCurrPeriodicStatsEntry 18 } csbCurrPeriodicStatsCallSetupCACBandwidthFailure OBJECT-TYPE SYNTAX Gauge32 MAX-ACCESS read-only STATUS current DESCRIPTION "This object indicates the number of call setup failures due to CAC bandwidth limit during this interval." ::= { csbCurrPeriodicStatsEntry 19 } csbCurrPeriodicStatsCallSetupCACMediaLimitFailure OBJECT-TYPE SYNTAX Gauge32 MAX-ACCESS read-only STATUS current DESCRIPTION "This object indicates the number of call setup failures due to CAC media limit during this interval." ::= { csbCurrPeriodicStatsEntry 20 } csbCurrPeriodicStatsCallSetupCACMediaUpdateFailure OBJECT-TYPE SYNTAX Gauge32 MAX-ACCESS read-only STATUS current DESCRIPTION "This object indicates the number of call update failure due to policy failure during this interval." ::= { csbCurrPeriodicStatsEntry 21 } csbCurrPeriodicStatsTimestamp OBJECT-TYPE SYNTAX OCTET STRING (SIZE (0..80)) MAX-ACCESS read-only STATUS current DESCRIPTION "This object indicates the current time at the start of each interval." ::= { csbCurrPeriodicStatsEntry 22 } csbCurrPeriodicStatsTranscodedCalls OBJECT-TYPE SYNTAX Gauge32 UNITS "calls" MAX-ACCESS read-only STATUS current DESCRIPTION "The object indicates the number of transcoded calls that are active during this interval." ::= { csbCurrPeriodicStatsEntry 23 } csbCurrPeriodicStatsTransratedCalls OBJECT-TYPE SYNTAX Gauge32 UNITS "calls" MAX-ACCESS read-only STATUS current DESCRIPTION "The object indicates the number of transrated calls that are active during this interval." ::= { csbCurrPeriodicStatsEntry 24 } csbCurrPeriodicStatsTotalCallUpdateFailure OBJECT-TYPE SYNTAX Gauge32 UNITS "calls" MAX-ACCESS read-only STATUS current DESCRIPTION "This object indicates the total number of call update failures during this interval." ::= { csbCurrPeriodicStatsEntry 25 } csbCurrPeriodicStatsActiveIpv6Calls OBJECT-TYPE SYNTAX Gauge32 UNITS "calls" MAX-ACCESS read-only STATUS current DESCRIPTION "This Object indicates the number of calls through SBC that use IPv6 signaling. This statistic totals all calls that traverse an IPv6 adjacency on either or both sides of SBC during this interval." ::= { csbCurrPeriodicStatsEntry 26 } csbCurrPeriodicStatsActiveEmergencyCalls OBJECT-TYPE SYNTAX Gauge32 UNITS "calls" MAX-ACCESS read-only STATUS current DESCRIPTION "This object indicates the number of calls through SBC that have been identified as emergency calls (by Number Analysis) during this interval." ::= { csbCurrPeriodicStatsEntry 27 } csbCurrPeriodicStatsActiveE2EmergencyCalls OBJECT-TYPE SYNTAX Gauge32 UNITS "calls" MAX-ACCESS read-only STATUS current DESCRIPTION "This object indicates the number of calls through SBC that have been identified as emergency calls (by Number Analysis) and have used the e2 interface to obtain location information for the caller during this interval." ::= { csbCurrPeriodicStatsEntry 28 } csbCurrPeriodicStatsImsRxActiveCalls OBJECT-TYPE SYNTAX Gauge32 UNITS "calls" MAX-ACCESS read-only STATUS current DESCRIPTION "This object indicates the total number of active calls which use IMS Rx, during this interval." ::= { csbCurrPeriodicStatsEntry 29 } csbCurrPeriodicStatsImsRxCallSetupFaiures OBJECT-TYPE SYNTAX Gauge32 UNITS "failures" MAX-ACCESS read-only STATUS current DESCRIPTION "This object indicates the total call Setup failures owing to IMS Rx failure during this interval." ::= { csbCurrPeriodicStatsEntry 30 } csbCurrPeriodicStatsImsRxCallRenegotiationAttempts OBJECT-TYPE SYNTAX Gauge32 UNITS "attempts" MAX-ACCESS read-only STATUS current DESCRIPTION "This object indicates the total call renegotiation attempts using IMS Rx during this interval." ::= { csbCurrPeriodicStatsEntry 31 } csbCurrPeriodicStatsImsRxCallRenegotiationFailures OBJECT-TYPE SYNTAX Gauge32 UNITS "failures" MAX-ACCESS read-only STATUS current DESCRIPTION "This object indicates the total call renegotiation failures owing to IMS Rx failure during this interval." ::= { csbCurrPeriodicStatsEntry 32 } csbCurrPeriodicStatsAudioTranscodedCalls OBJECT-TYPE SYNTAX Gauge32 UNITS "calls" MAX-ACCESS read-only STATUS current DESCRIPTION "The number of active audio transcoded calls through this adjacency or account during this interval." ::= { csbCurrPeriodicStatsEntry 33 } csbCurrPeriodicStatsFaxTranscodedCalls OBJECT-TYPE SYNTAX Gauge32 UNITS "calls" MAX-ACCESS read-only STATUS current DESCRIPTION "This object indicates the the number of active fax transcoded calls through this adjacency or account during this interval." ::= { csbCurrPeriodicStatsEntry 34 } csbCurrPeriodicStatsRtpDisallowedFailures OBJECT-TYPE SYNTAX Gauge32 UNITS "failures" MAX-ACCESS read-only STATUS current DESCRIPTION "This object indicates the total call setup failures due to RTP being proposed when not permitted during this interval." ::= { csbCurrPeriodicStatsEntry 35 } csbCurrPeriodicStatsSrtpDisallowedFailures OBJECT-TYPE SYNTAX Gauge32 UNITS "failures" MAX-ACCESS read-only STATUS current DESCRIPTION "This object indicates the total call setup failures due to SRTP being proposed when not permitted during this interval." ::= { csbCurrPeriodicStatsEntry 36 } csbCurrPeriodicStatsNonSrtpCalls OBJECT-TYPE SYNTAX Gauge32 UNITS "calls" MAX-ACCESS read-only STATUS current DESCRIPTION "This object indicates the number of active calls through this adjacency or account which do not use SRTP on any media channels during this interval." ::= { csbCurrPeriodicStatsEntry 37 } csbCurrPeriodicStatsSrtpNonIwCalls OBJECT-TYPE SYNTAX Gauge32 UNITS "calls" MAX-ACCESS read-only STATUS current DESCRIPTION "This object indicates the number of active calls through this adjacency or account that have one or more media channels which use SRTP. This count does not include media channels that provide interworking between RTP and SRTP during this interval." ::= { csbCurrPeriodicStatsEntry 38 } csbCurrPeriodicStatsSrtpIwCalls OBJECT-TYPE SYNTAX Gauge32 UNITS "calls" MAX-ACCESS read-only STATUS current DESCRIPTION "This object indicates the number of active calls through this adjacency or account that have one or more media channels that provide interworking between RTP and SRTP during this interval." ::= { csbCurrPeriodicStatsEntry 39 } csbCurrPeriodicStatsDtmfIw2833Calls OBJECT-TYPE SYNTAX Gauge32 UNITS "calls" MAX-ACCESS read-only STATUS current DESCRIPTION "This object indicates the number of active calls through this adjacency or account for which DTMF interworking is enabled between DTMF in signaling and DTMF in media via RFC 2833 during this interval." ::= { csbCurrPeriodicStatsEntry 40 } csbCurrPeriodicStatsDtmfIwInbandCalls OBJECT-TYPE SYNTAX Gauge32 UNITS "calls" MAX-ACCESS read-only STATUS current DESCRIPTION "This object indicates the number of active calls through this adjacency or account for which DTMF interworking is enabled between DTMF in signaling and DTMF in media via inband DTMF tones during this interval." ::= { csbCurrPeriodicStatsEntry 41 } csbCurrPeriodicStatsDtmfIw2833InbandCalls OBJECT-TYPE SYNTAX Gauge32 UNITS "calls" MAX-ACCESS read-only STATUS current DESCRIPTION "This object indicates the number of active calls through this adjacency or account for which DTMF interworking is enabled between DTMF in media via RFC 2833 and DTMF in media via inband DTMF tones during this interval." ::= { csbCurrPeriodicStatsEntry 42 } csbCurrPeriodicStatsTotalTapsRequested OBJECT-TYPE SYNTAX Gauge32 UNITS "attempts" MAX-ACCESS read-only STATUS current DESCRIPTION "This object indicates the lawful intercept tap attempts requested within the scope of this query during this interval." ::= { csbCurrPeriodicStatsEntry 43 } csbCurrPeriodicStatsTotalTapsSucceeded OBJECT-TYPE SYNTAX Gauge32 UNITS "success" MAX-ACCESS read-only STATUS current DESCRIPTION "This object indicates the lawful intercept tap attempts that have been successfully implemented within the scope of this query during this interval." ::= { csbCurrPeriodicStatsEntry 44 } csbCurrPeriodicStatsCurrentTaps OBJECT-TYPE SYNTAX Gauge32 UNITS "taps" MAX-ACCESS read-only STATUS current DESCRIPTION "This object indicates the Lawful intercept taps currently in place on calls within the scope of this query during this interval." ::= { csbCurrPeriodicStatsEntry 45 } csbCurrPeriodicIpsecCalls OBJECT-TYPE SYNTAX Gauge32 UNITS "calls" MAX-ACCESS read-only STATUS current DESCRIPTION "The number of active calls on this adjacency or account which are to or from registered subscribers using IPSEC during this interval." ::= { csbCurrPeriodicStatsEntry 46 } csbHistoryStatsTable OBJECT-TYPE SYNTAX SEQUENCE OF CsbHistoryStatsEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "This table provide historical measurement in various interval length defined by the csbHistoryStatsInterval object. Each interval may contain one or more entries to allow for detailed measurment to be collected. It is up to the platform to determine the number of intervals to be supported like 5 minutes, 15 minutes, 1 hour and 1 day. In addition, the number of historical entries is also determined by the platform resources. The gauge values are reported as: If the period being queried is previous5mins, this is the number of calls that were active at the end of the previous 5 minute period. Otherwise for the other intevals, this is an average value during the summary period, sampled at 5 minute intervals." ::= { ciscoSbcCallStatsMIBObjects 4 } csbHistoryStatsEntry OBJECT-TYPE SYNTAX CsbHistoryStatsEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "A conceptual row in the csbHistoryStatsTable. The entries in this table are updated as interval completes in the csbCurrPeriodicStatsTable table and the data is moved from that table to this one." INDEX { csbCallStatsInstanceIndex, csbCallStatsServiceIndex, csbHistoryStatsInterval, csbHistoryStatsElements } ::= { csbHistoryStatsTable 1 } CsbHistoryStatsEntry ::= SEQUENCE { csbHistoryStatsInterval CiscoSbcPeriodicStatsInterval, csbHistoryStatsElements Unsigned32, csbHistoryStatsActiveCalls Gauge32, csbHistoryStatsTotalCallAttempts Gauge32, csbHistoryStatsFailedCallAttempts Gauge32, csbHistoryStatsCallRoutingFailure Gauge32, csbHistoryStatsCallResourceFailure Gauge32, csbHistoryStatsCallMediaFailure Gauge32, csbHistoryStatsFailSigFailure Gauge32, csbHistoryStatsActiveCallFailure Gauge32, csbHistoryStatsCongestionFailure Gauge32, csbHistoryStatsCallSetupPolicyFailure Gauge32, csbHistoryStatsCallSetupNAPolicyFailure Gauge32, csbHistoryStatsCallSetupRoutingPolicyFailure Gauge32, csbHistoryStatsCallSetupCACPolicyFailure Gauge32, csbHistoryStatsCallSetupCACCallLimitFailure Gauge32, csbHistoryStatsCallSetupCACRateLimitFailure Gauge32, csbHistoryStatsCallSetupCACBandwidthFailure Gauge32, csbHistoryStatsCallSetupCACMediaLimitFailure Gauge32, csbHistoryStatsCallSetupCACMediaUpdateFailure Gauge32, csbHistoryStatsTimestamp OCTET STRING, csbHistroyStatsTranscodedCalls Gauge32, csbHistroyStatsTransratedCalls Gauge32, csbHistoryStatsTotalCallUpdateFailure Gauge32, csbHistoryStatsActiveIpv6Calls Gauge32, csbHistoryStatsActiveEmergencyCalls Gauge32, csbHistoryStatsActiveE2EmergencyCalls Gauge32, csbHistoryStatsImsRxActiveCalls Gauge32, csbHistoryStatsImsRxCallSetupFailures Gauge32, csbHistoryStatsImsRxCallRenegotiationAttempts Gauge32, csbHistoryStatsImsRxCallRenegotiationFailures Gauge32, csbHistoryStatsAudioTranscodedCalls Gauge32, csbHistoryStatsFaxTranscodedCalls Gauge32, csbHistoryStatsRtpDisallowedFailures Gauge32, csbHistoryStatsSrtpDisallowedFailures Gauge32, csbHistoryStatsNonSrtpCalls Gauge32, csbHistoryStatsSrtpNonIwCalls Gauge32, csbHistoryStatsSrtpIwCalls Gauge32, csbHistoryStatsDtmfIw2833Calls Gauge32, csbHistoryStatsDtmfIwInbandCalls Gauge32, csbHistoryStatsDtmfIw2833InbandCalls Gauge32, csbHistoryStatsTotalTapsRequested Gauge32, csbHistoryStatsTotalTapsSucceeded Gauge32, csbHistoryStatsCurrentTaps Gauge32, csbHistoryStatsIpsecCalls Gauge32 } csbHistoryStatsInterval OBJECT-TYPE SYNTAX CiscoSbcPeriodicStatsInterval MAX-ACCESS not-accessible STATUS current DESCRIPTION "This object identifies the interval for which the history statistics information is to be displayed. The interval values can be 5 min, 15 mins, 1 hour , 1 day. This object acts as index for the table." ::= { csbHistoryStatsEntry 1 } csbHistoryStatsElements OBJECT-TYPE SYNTAX Unsigned32 MAX-ACCESS not-accessible STATUS current DESCRIPTION "The platform assigns a number starting with one and increments it each for each new row. When the maximum number of row is reached the oldest rows are deleted. It is up to the platform to determine the number of entries for each interval. It is recommended that each platform support at least one entry for 5 min, 15 mins, 1 hour and 1 day intervals." ::= { csbHistoryStatsEntry 2 } csbHistoryStatsActiveCalls OBJECT-TYPE SYNTAX Gauge32 UNITS "calls" MAX-ACCESS read-only STATUS current DESCRIPTION "This object indicates the number of active calls history during this interval." ::= { csbHistoryStatsEntry 3 } csbHistoryStatsTotalCallAttempts OBJECT-TYPE SYNTAX Gauge32 MAX-ACCESS read-only STATUS current DESCRIPTION "This object indicates the number of total call attempts history during this interval." ::= { csbHistoryStatsEntry 4 } csbHistoryStatsFailedCallAttempts OBJECT-TYPE SYNTAX Gauge32 MAX-ACCESS read-only STATUS current DESCRIPTION "This object indicates the number of failed call attempts during this interval." ::= { csbHistoryStatsEntry 5 } csbHistoryStatsCallRoutingFailure OBJECT-TYPE SYNTAX Gauge32 MAX-ACCESS read-only STATUS current DESCRIPTION "This object indicates the number of call setup failures due to routing failures during this interval." ::= { csbHistoryStatsEntry 6 } csbHistoryStatsCallResourceFailure OBJECT-TYPE SYNTAX Gauge32 MAX-ACCESS read-only STATUS current DESCRIPTION "This object indicates the number of call setup failures due to resource failures during this interval." ::= { csbHistoryStatsEntry 7 } csbHistoryStatsCallMediaFailure OBJECT-TYPE SYNTAX Gauge32 MAX-ACCESS read-only STATUS current DESCRIPTION "This object indicates the number of call setup failures due to media failure during this interval." ::= { csbHistoryStatsEntry 8 } csbHistoryStatsFailSigFailure OBJECT-TYPE SYNTAX Gauge32 MAX-ACCESS read-only STATUS current DESCRIPTION "This object indicates the number of call setup failures due to signaling failure during this interval." ::= { csbHistoryStatsEntry 9 } csbHistoryStatsActiveCallFailure OBJECT-TYPE SYNTAX Gauge32 MAX-ACCESS read-only STATUS current DESCRIPTION "This object indicates the number of active call failures during this interval." ::= { csbHistoryStatsEntry 10 } csbHistoryStatsCongestionFailure OBJECT-TYPE SYNTAX Gauge32 MAX-ACCESS read-only STATUS current DESCRIPTION "This object indicates the number of call setup failures due to congestion during this interval." ::= { csbHistoryStatsEntry 11 } csbHistoryStatsCallSetupPolicyFailure OBJECT-TYPE SYNTAX Gauge32 MAX-ACCESS read-only STATUS current DESCRIPTION "This object indicates the number of call setup failures due to some policy violations during this interval." ::= { csbHistoryStatsEntry 12 } csbHistoryStatsCallSetupNAPolicyFailure OBJECT-TYPE SYNTAX Gauge32 MAX-ACCESS read-only STATUS current DESCRIPTION "This object indicates the number of call setup failures due to NA policy failure during this interval." ::= { csbHistoryStatsEntry 13 } csbHistoryStatsCallSetupRoutingPolicyFailure OBJECT-TYPE SYNTAX Gauge32 MAX-ACCESS read-only STATUS current DESCRIPTION "This object indicates the number of call setup failures due to routing policy failure during this interval." ::= { csbHistoryStatsEntry 14 } csbHistoryStatsCallSetupCACPolicyFailure OBJECT-TYPE SYNTAX Gauge32 MAX-ACCESS read-only STATUS current DESCRIPTION "This object indicates the number of call setup failures due to CAC policy failure during this interval." ::= { csbHistoryStatsEntry 15 } csbHistoryStatsCallSetupCACCallLimitFailure OBJECT-TYPE SYNTAX Gauge32 MAX-ACCESS read-only STATUS current DESCRIPTION "This object indicates the number of call setup failures due to CAC call limit during this interval." ::= { csbHistoryStatsEntry 16 } csbHistoryStatsCallSetupCACRateLimitFailure OBJECT-TYPE SYNTAX Gauge32 MAX-ACCESS read-only STATUS current DESCRIPTION "This object indicates the number of call setup failures due to CAC call rate limit during this interval." ::= { csbHistoryStatsEntry 17 } csbHistoryStatsCallSetupCACBandwidthFailure OBJECT-TYPE SYNTAX Gauge32 MAX-ACCESS read-only STATUS current DESCRIPTION "This object indicates the number of call setup failures due to CAC bandwidth limit during this interval." ::= { csbHistoryStatsEntry 18 } csbHistoryStatsCallSetupCACMediaLimitFailure OBJECT-TYPE SYNTAX Gauge32 MAX-ACCESS read-only STATUS current DESCRIPTION "This object indicates the number of call setup failures due to CAC media limit during this interval." ::= { csbHistoryStatsEntry 19 } csbHistoryStatsCallSetupCACMediaUpdateFailure OBJECT-TYPE SYNTAX Gauge32 MAX-ACCESS read-only STATUS current DESCRIPTION "This object indicates the number of call update failure due to policy failure during this interval." ::= { csbHistoryStatsEntry 20 } csbHistoryStatsTimestamp OBJECT-TYPE SYNTAX OCTET STRING (SIZE (0..80)) MAX-ACCESS read-only STATUS current DESCRIPTION "This object indicates the time at the start of the interval when measurements were first collected for this interval in the csbCurrPeriodicStatsTable." ::= { csbHistoryStatsEntry 21 } csbHistroyStatsTranscodedCalls OBJECT-TYPE SYNTAX Gauge32 UNITS "calls" MAX-ACCESS read-only STATUS current DESCRIPTION "The object indicates the number of active transcoded calls during this interval." ::= { csbHistoryStatsEntry 22 } csbHistroyStatsTransratedCalls OBJECT-TYPE SYNTAX Gauge32 UNITS "calls" MAX-ACCESS read-only STATUS current DESCRIPTION "The object indicates the number of active transrated calls during this interval." ::= { csbHistoryStatsEntry 23 } csbHistoryStatsTotalCallUpdateFailure OBJECT-TYPE SYNTAX Gauge32 UNITS "calls" MAX-ACCESS read-only STATUS current DESCRIPTION "This object indicates the total call update failures during this interval." ::= { csbHistoryStatsEntry 24 } csbHistoryStatsActiveIpv6Calls OBJECT-TYPE SYNTAX Gauge32 UNITS "calls" MAX-ACCESS read-only STATUS current DESCRIPTION "This Object indicates the number of calls through SBC that use IPv6 signaling. This statistic totals all calls that traverse an IPv6 adjacency on either or both sides of SBC during this interval." ::= { csbHistoryStatsEntry 25 } csbHistoryStatsActiveEmergencyCalls OBJECT-TYPE SYNTAX Gauge32 UNITS "calls" MAX-ACCESS read-only STATUS current DESCRIPTION "This object indicates the number of calls through SBC that have been identified as emergency calls (by Number Analysis) during this interval." ::= { csbHistoryStatsEntry 26 } csbHistoryStatsActiveE2EmergencyCalls OBJECT-TYPE SYNTAX Gauge32 UNITS "calls" MAX-ACCESS read-only STATUS current DESCRIPTION "This object indicates the number of calls through SBC that have been identified as emergency calls (by Number Analysis) and have used the e2 interface to obtain location information for the caller." ::= { csbHistoryStatsEntry 27 } csbHistoryStatsImsRxActiveCalls OBJECT-TYPE SYNTAX Gauge32 UNITS "calls" MAX-ACCESS read-only STATUS current DESCRIPTION "This object indicates the total number of active calls which use IMS Rx, during this interval." ::= { csbHistoryStatsEntry 28 } csbHistoryStatsImsRxCallSetupFailures OBJECT-TYPE SYNTAX Gauge32 UNITS "failures" MAX-ACCESS read-only STATUS current DESCRIPTION "This object indicates the total call setup failures owing to IMS Rx failure during this interval." ::= { csbHistoryStatsEntry 29 } csbHistoryStatsImsRxCallRenegotiationAttempts OBJECT-TYPE SYNTAX Gauge32 UNITS "attempts" MAX-ACCESS read-only STATUS current DESCRIPTION "This object indicates the total call renegotiation attempts using IMS Rx during this interval." ::= { csbHistoryStatsEntry 30 } csbHistoryStatsImsRxCallRenegotiationFailures OBJECT-TYPE SYNTAX Gauge32 UNITS "failures" MAX-ACCESS read-only STATUS current DESCRIPTION "This object indicates the total call renegotiation failures owing to IMS Rx failure during this interval." ::= { csbHistoryStatsEntry 31 } csbHistoryStatsAudioTranscodedCalls OBJECT-TYPE SYNTAX Gauge32 UNITS "calls" MAX-ACCESS read-only STATUS current DESCRIPTION "The number of active audio transcoded calls through this adjacency or account during this interval." ::= { csbHistoryStatsEntry 32 } csbHistoryStatsFaxTranscodedCalls OBJECT-TYPE SYNTAX Gauge32 UNITS "calls" MAX-ACCESS read-only STATUS current DESCRIPTION "This object indicates the the number of active fax transcoded calls through this adjacency or account during this interval." ::= { csbHistoryStatsEntry 33 } csbHistoryStatsRtpDisallowedFailures OBJECT-TYPE SYNTAX Gauge32 UNITS "failures" MAX-ACCESS read-only STATUS current DESCRIPTION "This object indicates the total call setup failures due to RTP being proposed when not permitted during this interval." ::= { csbHistoryStatsEntry 34 } csbHistoryStatsSrtpDisallowedFailures OBJECT-TYPE SYNTAX Gauge32 UNITS "failures" MAX-ACCESS read-only STATUS current DESCRIPTION "This object indicates the total call setup failures due to SRTP being proposed when not permitted during this interval." ::= { csbHistoryStatsEntry 35 } csbHistoryStatsNonSrtpCalls OBJECT-TYPE SYNTAX Gauge32 UNITS "calls" MAX-ACCESS read-only STATUS current DESCRIPTION "This object indicates the number of active calls through this adjacency or account which do not use SRTP on any media channels during this interval." ::= { csbHistoryStatsEntry 36 } csbHistoryStatsSrtpNonIwCalls OBJECT-TYPE SYNTAX Gauge32 UNITS "calls" MAX-ACCESS read-only STATUS current DESCRIPTION "This object indicates the number of active calls through this adjacency or account that have one or more media channels that use SRTP but no media channels that provide interworking between RTP and SRTP during this interval." ::= { csbHistoryStatsEntry 37 } csbHistoryStatsSrtpIwCalls OBJECT-TYPE SYNTAX Gauge32 UNITS "calls" MAX-ACCESS read-only STATUS current DESCRIPTION "This object indicates the number of active calls through this adjacency or account that have one or more media channels that provide interworking between RTP and SRTP during this interval." ::= { csbHistoryStatsEntry 38 } csbHistoryStatsDtmfIw2833Calls OBJECT-TYPE SYNTAX Gauge32 UNITS "calls" MAX-ACCESS read-only STATUS current DESCRIPTION "This object indicates the number of active calls through this adjacency or account for which DTMF interworking is enabled between DTMF in signaling and DTMF in media via RFC 2833 during this interval." ::= { csbHistoryStatsEntry 39 } csbHistoryStatsDtmfIwInbandCalls OBJECT-TYPE SYNTAX Gauge32 UNITS "calls" MAX-ACCESS read-only STATUS current DESCRIPTION "This object indicates the number of active calls through this adjacency or account for which DTMF interworking is enabled between DTMF in signaling and DTMF in media via inband DTMF tones during this interval." ::= { csbHistoryStatsEntry 40 } csbHistoryStatsDtmfIw2833InbandCalls OBJECT-TYPE SYNTAX Gauge32 UNITS "calls" MAX-ACCESS read-only STATUS current DESCRIPTION "This object indicates the number of active calls through this adjacency or account for which DTMF interworking is enabled between DTMF in media via RFC 2833 and DTMF in media via inband DTMF tones during this interval." ::= { csbHistoryStatsEntry 41 } csbHistoryStatsTotalTapsRequested OBJECT-TYPE SYNTAX Gauge32 UNITS "attempts" MAX-ACCESS read-only STATUS current DESCRIPTION "This object indicates the lawful intercept tap attempts requested within the scope of this query during this interval." ::= { csbHistoryStatsEntry 42 } csbHistoryStatsTotalTapsSucceeded OBJECT-TYPE SYNTAX Gauge32 UNITS "success" MAX-ACCESS read-only STATUS current DESCRIPTION "This object indicates the lawful intercept tap attempts that have been successfully implemented within the scope of this query during this interval." ::= { csbHistoryStatsEntry 43 } csbHistoryStatsCurrentTaps OBJECT-TYPE SYNTAX Gauge32 UNITS "taps" MAX-ACCESS read-only STATUS current DESCRIPTION "This object indicates the Lawful intercept taps currently in place on calls within the scope of this query during this interval." ::= { csbHistoryStatsEntry 44 } csbHistoryStatsIpsecCalls OBJECT-TYPE SYNTAX Gauge32 UNITS "calls" MAX-ACCESS read-only STATUS current DESCRIPTION "The number of active calls on this adjacency or account which are to or from registered subscribers using IPSEC during this interval." ::= { csbHistoryStatsEntry 45 } csbPerFlowStatsTable OBJECT-TYPE SYNTAX SEQUENCE OF CsbPerFlowStatsEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "This table describes statistics table for each call flow. The indices of the table are virtual media gateway id, gate id, falow pair id and side id (indices for side A or side B). The other indices of this table are csbCallStatsInstanceIndex defined in csbCallStatsInstanceTable and csbCallStatsServiceIndex defined in csbCallStatsTable." ::= { ciscoSbcCallStatsMIBObjects 5 } csbPerFlowStatsEntry OBJECT-TYPE SYNTAX CsbPerFlowStatsEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "An conceptual row in the csbPerFlowStatsTable. There is an entry in this table for vdbe Id, gate id, flow pair id and side id. The other indices of this table are csbCallStatsInstanceIndex defined in csbCallStatsInstanceTable and csbCallStatsServiceIndex defined in csbCallStatsTable." INDEX { csbCallStatsInstanceIndex, csbCallStatsServiceIndex, csbPerFlowStatsVdbeId, csbPerFlowStatsGateId, csbPerFlowStatsFlowPairId, csbPerFlowStatsSideId } ::= { csbPerFlowStatsTable 1 } CsbPerFlowStatsEntry ::= SEQUENCE { csbPerFlowStatsVdbeId Integer32, csbPerFlowStatsGateId Integer32, csbPerFlowStatsFlowPairId Integer32, csbPerFlowStatsSideId INTEGER, csbPerFlowStatsFlowType INTEGER, csbPerFlowStatsRTPPktsSent Counter64, csbPerFlowStatsRTPPktsRcvd Counter64, csbPerFlowStatsRTPPktsDiscard Counter64, csbPerFlowStatsRTPOctetsSent Counter64, csbPerFlowStatsRTPOctetsRcvd Counter64, csbPerFlowStatsRTPOctetsDiscard Counter64, csbPerFlowStatsRTCPPktsSent Counter64, csbPerFlowStatsRTCPPktsRcvd Counter64, csbPerFlowStatsRTCPPktsLost Counter64, csbPerFlowStatsEPJitter Counter64, csbPerFlowStatsTmanPerMbs Gauge32, csbPerFlowStatsTmanPerSdr Gauge32, csbPerFlowStatsDscpSettings SnmpAdminString, csbPerFlowStatsAdrStatus OCTET STRING, csbPerFlowStatsQASettings OCTET STRING, csbPerFlowStatsRTPPktsLost Counter64 } csbPerFlowStatsVdbeId OBJECT-TYPE SYNTAX Integer32 (0..255) MAX-ACCESS not-accessible STATUS current DESCRIPTION "This object identifies the virtual media gateway id. This object also acts as an index for the table." ::= { csbPerFlowStatsEntry 1 } csbPerFlowStatsGateId OBJECT-TYPE SYNTAX Integer32 (0..65535) MAX-ACCESS not-accessible STATUS current DESCRIPTION "This object identifies the gate id. This object also acts as an index for the table." ::= { csbPerFlowStatsEntry 2 } csbPerFlowStatsFlowPairId OBJECT-TYPE SYNTAX Integer32 (0..65535) MAX-ACCESS not-accessible STATUS current DESCRIPTION "This object identifies the flow pair id. This object also acts as an index for the table." ::= { csbPerFlowStatsEntry 3 } csbPerFlowStatsSideId OBJECT-TYPE SYNTAX INTEGER { sideA(1), sideB(2) } MAX-ACCESS not-accessible STATUS current DESCRIPTION "This object identifies the index corresponding to side of flow pair either side A or side B. This object also acts as an index for the table." ::= { csbPerFlowStatsEntry 4 } csbPerFlowStatsFlowType OBJECT-TYPE SYNTAX INTEGER { media(1), signalling(2) } MAX-ACCESS read-only STATUS current DESCRIPTION "This object indicates the type of the flow, like media flow, signaling flow etc." ::= { csbPerFlowStatsEntry 5 } csbPerFlowStatsRTPPktsSent OBJECT-TYPE SYNTAX Counter64 UNITS "packets" MAX-ACCESS read-only STATUS current DESCRIPTION "This object indicates the number of RTP packets sent per flow by the SBC." ::= { csbPerFlowStatsEntry 6 } csbPerFlowStatsRTPPktsRcvd OBJECT-TYPE SYNTAX Counter64 UNITS "packets" MAX-ACCESS read-only STATUS current DESCRIPTION "This object indicates the number of RTP packets received per flow by the SBC." ::= { csbPerFlowStatsEntry 7 } csbPerFlowStatsRTPPktsDiscard OBJECT-TYPE SYNTAX Counter64 UNITS "packets" MAX-ACCESS read-only STATUS current DESCRIPTION "This object indicates the number of RTP packets discarded per flow by the SBC." ::= { csbPerFlowStatsEntry 8 } csbPerFlowStatsRTPOctetsSent OBJECT-TYPE SYNTAX Counter64 UNITS "octets" MAX-ACCESS read-only STATUS current DESCRIPTION "This object indicates the number of RTP octets sent per flow by the SBC." ::= { csbPerFlowStatsEntry 9 } csbPerFlowStatsRTPOctetsRcvd OBJECT-TYPE SYNTAX Counter64 UNITS "octets" MAX-ACCESS read-only STATUS current DESCRIPTION "This object indicates the number of RTP octets received per flow by the SBC." ::= { csbPerFlowStatsEntry 10 } csbPerFlowStatsRTPOctetsDiscard OBJECT-TYPE SYNTAX Counter64 UNITS "octets" MAX-ACCESS read-only STATUS current DESCRIPTION "This object indicates the number of RTP octets discarded per flow by the SBC." ::= { csbPerFlowStatsEntry 11 } csbPerFlowStatsRTCPPktsSent OBJECT-TYPE SYNTAX Counter64 UNITS "packets" MAX-ACCESS read-only STATUS current DESCRIPTION "The number of RTP packets sent by the remote end point to this MG on this flow. Comparing this with the local number of RTP packets received from the remote end point gives an indication of how many incoming packets were dropped on this leg of the call. This information is from RTCP packet. Not all endpoints report this statistic, if it is not available it will be set to zero. This statistic will not be available for signaling flows." ::= { csbPerFlowStatsEntry 12 } csbPerFlowStatsRTCPPktsRcvd OBJECT-TYPE SYNTAX Counter64 UNITS "packets" MAX-ACCESS read-only STATUS current DESCRIPTION "The number of RTP packets received by the remote end point from this MG on this flow. Comparing this with the local number of RTP packets sent from this MG to the remote endpoint gives an indication of how many outgoing packets were dropped on this leg of the call. This information is from RTCP packet. Not all endpoints report this statistic, if it is not available it will be set to zero. This statistic will not be available for signaling flows." ::= { csbPerFlowStatsEntry 13 } csbPerFlowStatsRTCPPktsLost OBJECT-TYPE SYNTAX Counter64 UNITS "packets" MAX-ACCESS read-only STATUS current DESCRIPTION "The number of RTP packets reported as lost by the remote end point on this flow. This information is from RTCP packet. Not all endpoints report this statistic, if it is not available it will be set to zero. This statistic will not be available for signaling flows." ::= { csbPerFlowStatsEntry 14 } csbPerFlowStatsEPJitter OBJECT-TYPE SYNTAX Counter64 UNITS "milliseconds" MAX-ACCESS read-only STATUS current DESCRIPTION "This object indicates the End Point jitter per flow in the SBC." ::= { csbPerFlowStatsEntry 15 } csbPerFlowStatsTmanPerMbs OBJECT-TYPE SYNTAX Gauge32 UNITS "bytes" MAX-ACCESS read-only STATUS current DESCRIPTION "This object indicates the maximum burst size for the current FlowPair." ::= { csbPerFlowStatsEntry 16 } csbPerFlowStatsTmanPerSdr OBJECT-TYPE SYNTAX Gauge32 UNITS "kilobytes per second" MAX-ACCESS read-only STATUS current DESCRIPTION "This object indicates the bandwidth reserved for flow in kilobytes/second." ::= { csbPerFlowStatsEntry 17 } csbPerFlowStatsDscpSettings OBJECT-TYPE SYNTAX SnmpAdminString MAX-ACCESS read-only STATUS current DESCRIPTION "This object indicates the mark packets sent for the current FlowPair with, or zero if none set. The DSCP is a 6-bit value, which will be present in the top 6 bits of the lowest byte of this field." ::= { csbPerFlowStatsEntry 18 } csbPerFlowStatsAdrStatus OBJECT-TYPE SYNTAX OCTET STRING (SIZE (0..10)) MAX-ACCESS read-only STATUS current DESCRIPTION "This object indicates whether the flow on the current FlowPair has subscribed for the NAT latch event." ::= { csbPerFlowStatsEntry 19 } csbPerFlowStatsQASettings OBJECT-TYPE SYNTAX OCTET STRING (SIZE (0..10)) MAX-ACCESS read-only STATUS current DESCRIPTION "This object indicates the flow on the current FlowPair has subscribed for the media loss event." ::= { csbPerFlowStatsEntry 20 } csbPerFlowStatsRTPPktsLost OBJECT-TYPE SYNTAX Counter64 UNITS "packets" MAX-ACCESS read-only STATUS current DESCRIPTION "This object indicates the number of RTP packets lost per flow by the SBC." ::= { csbPerFlowStatsEntry 21 } csbH248StatsTable OBJECT-TYPE SYNTAX SEQUENCE OF CsbH248StatsEntry MAX-ACCESS not-accessible STATUS deprecated DESCRIPTION "This table describes the H.248 statistics for SBC. The index of the table is service index which corresponds to a particular service configured on the SBC and the index assigned to a particular H.248 controller. The other index of this table is csbCallStatsInstanceIndex defined in csbCallStatsInstanceTable. This table is replaced by the csbH248StatsRev1Table." ::= { ciscoSbcCallStatsMIBObjects 6 } csbH248StatsEntry OBJECT-TYPE SYNTAX CsbH248StatsEntry MAX-ACCESS not-accessible STATUS deprecated DESCRIPTION "An conceptual row in the csbCallStath248Table. There is an entry in this table for the particular controller by a value of csbH248StatsCtrlrIndex. The other indices of this table are csbCallStatsInstanceIndex defined in csbCallStatsInstanceTable and csbCallStatsServiceIndex defined in csbCallStatsTable." INDEX { csbCallStatsInstanceIndex, csbCallStatsServiceIndex, csbH248StatsCtrlrIndex } ::= { csbH248StatsTable 1 } CsbH248StatsEntry ::= SEQUENCE { csbH248StatsCtrlrIndex Integer32, csbH248StatsRequestsSent Counter32, csbH248StatsRequestsRcvd Counter32, csbH248StatsRequestsFailed Counter32, csbH248StatsRequestsRetried Counter32, csbH248StatsRepliesSent Counter32, csbH248StatsRepliesRcvd Counter32, csbH248StatsRepliesRetried Counter32, csbH248StatsSegPktsSent Counter32, csbH248StatsSegPktsRcvd Counter32, csbH248StatsEstablishedTime OCTET STRING, csbH248StatsTMaxTimeoutVal Integer32, csbH248StatsRTT Gauge32, csbH248StatsLT Gauge32 } csbH248StatsCtrlrIndex OBJECT-TYPE SYNTAX Integer32 (1..50) MAX-ACCESS not-accessible STATUS deprecated DESCRIPTION "This object identifies the controller index of the H.248 server. This is also the index for the table." ::= { csbH248StatsEntry 1 } csbH248StatsRequestsSent OBJECT-TYPE SYNTAX Counter32 MAX-ACCESS read-only STATUS deprecated DESCRIPTION "This object indicates the requests sent through the Session Controller Interface to an SBE or DBE." ::= { csbH248StatsEntry 2 } csbH248StatsRequestsRcvd OBJECT-TYPE SYNTAX Counter32 MAX-ACCESS read-only STATUS deprecated DESCRIPTION "This object indicates the requests received through the Session Controller Interface to an SBE or DBE." ::= { csbH248StatsEntry 3 } csbH248StatsRequestsFailed OBJECT-TYPE SYNTAX Counter32 MAX-ACCESS read-only STATUS deprecated DESCRIPTION "This object indicates the requests failed on session Controller Interface to an SBE or DBE." ::= { csbH248StatsEntry 4 } csbH248StatsRequestsRetried OBJECT-TYPE SYNTAX Counter32 MAX-ACCESS read-only STATUS deprecated DESCRIPTION "This object indicates the requests retried through the Session Controller Interface to an SBE or DBE." ::= { csbH248StatsEntry 5 } csbH248StatsRepliesSent OBJECT-TYPE SYNTAX Counter32 MAX-ACCESS read-only STATUS deprecated DESCRIPTION "This object indicates the number of replies sent through the Session Controller Interface to an SBE or DBE." ::= { csbH248StatsEntry 6 } csbH248StatsRepliesRcvd OBJECT-TYPE SYNTAX Counter32 MAX-ACCESS read-only STATUS deprecated DESCRIPTION "This object indicates the number of replies received from the Session Controller Interface to an SBE or DBE." ::= { csbH248StatsEntry 7 } csbH248StatsRepliesRetried OBJECT-TYPE SYNTAX Counter32 MAX-ACCESS read-only STATUS deprecated DESCRIPTION "This object indicates the number of replies retried through the Session Controller Interface to an SBE or DBE." ::= { csbH248StatsEntry 8 } csbH248StatsSegPktsSent OBJECT-TYPE SYNTAX Counter32 MAX-ACCESS read-only STATUS deprecated DESCRIPTION "This object indicates the number of packets sent through the Session Controller Interface to an SBE or DBE." ::= { csbH248StatsEntry 9 } csbH248StatsSegPktsRcvd OBJECT-TYPE SYNTAX Counter32 MAX-ACCESS read-only STATUS deprecated DESCRIPTION "This object indicates the number of packets received from the Session Controller Interface to an SBE or DBE." ::= { csbH248StatsEntry 10 } csbH248StatsEstablishedTime OBJECT-TYPE SYNTAX OCTET STRING (SIZE (0..80)) MAX-ACCESS read-only STATUS deprecated DESCRIPTION "This object indicates the H.248 Controller established time (the time at which the association became established)." ::= { csbH248StatsEntry 11 } csbH248StatsTMaxTimeoutVal OBJECT-TYPE SYNTAX Integer32 UNITS "milliseconds" MAX-ACCESS read-only STATUS deprecated DESCRIPTION "This object indicates the T-Max timeout value. This field specifies the maximum delay (in milliseconds) for a response from an MGC before deciding that the request has failed." ::= { csbH248StatsEntry 12 } csbH248StatsRTT OBJECT-TYPE SYNTAX Gauge32 UNITS "milliseconds" MAX-ACCESS read-only STATUS deprecated DESCRIPTION "This object indicates the calculated RTT value. This field specifies the maximum round trip propagation delay in the network (in milliseconds)." ::= { csbH248StatsEntry 13 } csbH248StatsLT OBJECT-TYPE SYNTAX Gauge32 UNITS "milliseconds" MAX-ACCESS read-only STATUS deprecated DESCRIPTION "This object indicates the LT value calculated from RTT value and Max timeout value. This field specifies the maximum delay (in milliseconds) for a response from an MGC plus the maximum round trip propagation delay in the network (in milliseconds)." ::= { csbH248StatsEntry 14 } csbH248StatsRev1Table OBJECT-TYPE SYNTAX SEQUENCE OF CsbH248StatsRev1Entry MAX-ACCESS not-accessible STATUS current DESCRIPTION "This table describes the H.248 statistics for SBC. The index of the table is service index which corresponds to a particular service configured on the SBC and the index assigned to a particular H.248 controller. The other index of this table is csbCallStatsInstanceIndex defined in csbCallStatsInstanceTable." ::= { ciscoSbcCallStatsMIBObjects 7 } csbH248StatsRev1Entry OBJECT-TYPE SYNTAX CsbH248StatsRev1Entry MAX-ACCESS not-accessible STATUS current DESCRIPTION "An conceptual row in the csbCallStath248Table. There is an entry in this table for the particular Vdbe by a value of csbH248StatsVdbeId. The other indices of this table are csbCallStatsInstanceIndex defined in csbCallStatsInstanceTable and csbCallStatsServiceIndex defined in csbCallStatsTable." INDEX { csbCallStatsInstanceIndex, csbCallStatsServiceIndex, csbH248StatsVdbeId } ::= { csbH248StatsRev1Table 1 } CsbH248StatsRev1Entry ::= SEQUENCE { csbH248StatsVdbeId Integer32, csbH248StatsRequestsSentRev1 Counter32, csbH248StatsRequestsRcvdRev1 Counter32, csbH248StatsRequestsFailedRev1 Counter32, csbH248StatsRequestsRetriedRev1 Counter32, csbH248StatsRepliesSentRev1 Counter32, csbH248StatsRepliesRcvdRev1 Counter32, csbH248StatsRepliesRetriedRev1 Counter32, csbH248StatsSegPktsSentRev1 Counter32, csbH248StatsSegPktsRcvdRev1 Counter32, csbH248StatsEstablishedTimeRev1 OCTET STRING, csbH248StatsTMaxTimeoutValRev1 Integer32, csbH248StatsRTTRev1 Gauge32, csbH248StatsLTRev1 Gauge32 } csbH248StatsVdbeId OBJECT-TYPE SYNTAX Integer32 (0..255) MAX-ACCESS not-accessible STATUS current DESCRIPTION "This object identifies the virtual media gateway id. This is also the index for the table." ::= { csbH248StatsRev1Entry 1 } csbH248StatsRequestsSentRev1 OBJECT-TYPE SYNTAX Counter32 MAX-ACCESS read-only STATUS current DESCRIPTION "This object indicates the requests sent through the Session Controller Interface to an SBE or DBE." ::= { csbH248StatsRev1Entry 2 } csbH248StatsRequestsRcvdRev1 OBJECT-TYPE SYNTAX Counter32 MAX-ACCESS read-only STATUS current DESCRIPTION "This object indicates the requests received through the Session Controller Interface to an SBE or DBE." ::= { csbH248StatsRev1Entry 3 } csbH248StatsRequestsFailedRev1 OBJECT-TYPE SYNTAX Counter32 MAX-ACCESS read-only STATUS current DESCRIPTION "This object indicates the requests failed on session Controller Interface to an SBE or DBE." ::= { csbH248StatsRev1Entry 4 } csbH248StatsRequestsRetriedRev1 OBJECT-TYPE SYNTAX Counter32 MAX-ACCESS read-only STATUS current DESCRIPTION "This object indicates the requests retried through the Session Controller Interface to an SBE or DBE." ::= { csbH248StatsRev1Entry 5 } csbH248StatsRepliesSentRev1 OBJECT-TYPE SYNTAX Counter32 MAX-ACCESS read-only STATUS current DESCRIPTION "This object indicates the number of replies sent through the Session Controller Interface to an SBE or DBE." ::= { csbH248StatsRev1Entry 6 } csbH248StatsRepliesRcvdRev1 OBJECT-TYPE SYNTAX Counter32 MAX-ACCESS read-only STATUS current DESCRIPTION "This object indicates the number of replies received from the Session Controller Interface to an SBE or DBE." ::= { csbH248StatsRev1Entry 7 } csbH248StatsRepliesRetriedRev1 OBJECT-TYPE SYNTAX Counter32 MAX-ACCESS read-only STATUS current DESCRIPTION "This object indicates the number of replies retried through the Session Controller Interface to an SBE or DBE." ::= { csbH248StatsRev1Entry 8 } csbH248StatsSegPktsSentRev1 OBJECT-TYPE SYNTAX Counter32 MAX-ACCESS read-only STATUS current DESCRIPTION "This object indicates the number of response segments sent by DBE. This field will only be present if segmentation is enabled on this association." ::= { csbH248StatsRev1Entry 9 } csbH248StatsSegPktsRcvdRev1 OBJECT-TYPE SYNTAX Counter32 MAX-ACCESS read-only STATUS current DESCRIPTION "This object indicates the number of response segments received by DBE. This field will only be present if segmentation is enabled on this association." ::= { csbH248StatsRev1Entry 10 } csbH248StatsEstablishedTimeRev1 OBJECT-TYPE SYNTAX OCTET STRING (SIZE (0..80)) MAX-ACCESS read-only STATUS current DESCRIPTION "This object indicates the H.248 Controller established time (the time at which the association became established)." ::= { csbH248StatsRev1Entry 11 } csbH248StatsTMaxTimeoutValRev1 OBJECT-TYPE SYNTAX Integer32 UNITS "milliseconds" MAX-ACCESS read-only STATUS current DESCRIPTION "This object indicates the T-Max timeout value. This field specifies the maximum delay (in milliseconds) for a response from an MGC before deciding that the request has failed." ::= { csbH248StatsRev1Entry 12 } csbH248StatsRTTRev1 OBJECT-TYPE SYNTAX Gauge32 UNITS "milliseconds" MAX-ACCESS read-only STATUS current DESCRIPTION "This object indicates the calculated RTT value. This field specifies the maximum round trip propagation delay in the network (in milliseconds)." ::= { csbH248StatsRev1Entry 13 } csbH248StatsLTRev1 OBJECT-TYPE SYNTAX Gauge32 UNITS "milliseconds" MAX-ACCESS read-only STATUS current DESCRIPTION "This object indicates the LT value calculated from RTT value and Max timeout value. This field specifies the maximum delay (in milliseconds) for a response from an MGC plus the maximum round trip propagation delay in the network (in milliseconds)." ::= { csbH248StatsRev1Entry 14 } csbCallStatsMIBCompliances OBJECT IDENTIFIER ::= { ciscoSbcCallStatsMIBConform 1 } csbCallStatsMIBGroups OBJECT IDENTIFIER ::= { ciscoSbcCallStatsMIBConform 2 } csbCallStatsMIBCompliance MODULE-COMPLIANCE STATUS deprecated DESCRIPTION "This is a default module-compliance containing csbCallStatsMIBGroups." MODULE -- this module MANDATORY-GROUPS { csbGlobalStatsGroup, csbCurrPeriodicStatsGroup, csbHistoryStatsGroup, csbPerFlowStatsGroup, csbH248StatsGroup, csbStatsInstanceGroup } ::= { csbCallStatsMIBCompliances 1 } csbCallStatsMIBComplianceRev1 MODULE-COMPLIANCE STATUS deprecated DESCRIPTION "This is a default module-compliance containing csbCallStatsMIBGroups." MODULE -- this module MANDATORY-GROUPS { csbGlobalStatsGroup, csbCurrPeriodicStatsGroup, csbHistoryStatsGroup, csbPerFlowStatsGroup, csbH248StatsGroupRev1, csbStatsInstanceGroup } ::= { csbCallStatsMIBCompliances 2 } csbCallStatsMIBComplianceRev2 MODULE-COMPLIANCE STATUS current DESCRIPTION "This is a default module-compliance containing csbCallStatsMIBGroups." MODULE -- this module MANDATORY-GROUPS { csbGlobalStatsGroup, csbCurrPeriodicStatsGroup, csbHistoryStatsGroup, csbPerFlowStatsGroup, csbH248StatsGroupRev1, csbStatsInstanceGroup, csbGlobalStatsGroupSup1, csbCurrPeriodicStatsGroupSup1, csbHistoryStatsGroupSup1, csbPerFlowStatsGroupSup1 } ::= { csbCallStatsMIBCompliances 3 } csbStatsInstanceGroup OBJECT-GROUP OBJECTS { csbCallStatsInstancePhysicalIndex } STATUS current DESCRIPTION "A collection of objects providing physical entity index for cisco Session border Controller (SBC)." ::= { csbCallStatsMIBGroups 1 } -- Units of Conformance csbGlobalStatsGroup OBJECT-GROUP OBJECTS { csbCallStatsCallsHigh, csbCallStatsRate1Sec, csbCallStatsCallsLow, csbCallStatsAvailableFlows, csbCallStatsUsedFlows, csbCallStatsTotalFlows, csbCallStatsRTPPktsRcvd, csbCallStatsRTPPktsDiscard, csbCallStatsUsedSigFlows, csbCallStatsTotalSigFlows, csbCallStatsAvailablePktRate, csbCallStatsPeakFlows, csbCallStatsUnclassifiedPkts, csbCallStatsRTPOctetsSent, csbCallStatsRTPOctetsRcvd, csbCallStatsRTPOctetsDiscard, csbCallStatsPeakSigFlows, csbCallStatsSbcName, csbCallStatsRTPPktsSent, csbCallStatsNoMediaCount, csbCallStatsRouteErrors } STATUS current DESCRIPTION "A collection of objects providing global statistics for cisco Session border Controller (SBC)." ::= { csbCallStatsMIBGroups 2 } csbCurrPeriodicStatsGroup OBJECT-GROUP OBJECTS { csbCurrPeriodicStatsActiveCalls, csbCurrPeriodicStatsActivatingCalls, csbCurrPeriodicStatsDeactivatingCalls, csbCurrPeriodicStatsTotalCallAttempts, csbCurrPeriodicStatsFailedCallAttempts, csbCurrPeriodicStatsCallRoutingFailure, csbCurrPeriodicStatsCallResourceFailure, csbCurrPeriodicStatsCallMediaFailure, csbCurrPeriodicStatsCallSigFailure, csbCurrPeriodicStatsActiveCallFailure, csbCurrPeriodicStatsCongestionFailure, csbCurrPeriodicStatsCallSetupPolicyFailure, csbCurrPeriodicStatsCallSetupNAPolicyFailure, csbCurrPeriodicStatsCallSetupRoutingPolicyFailure, csbCurrPeriodicStatsCallSetupCACPolicyFailure, csbCurrPeriodicStatsCallSetupCACCallLimitFailure, csbCurrPeriodicStatsCallSetupCACRateLimitFailure, csbCurrPeriodicStatsCallSetupCACBandwidthFailure, csbCurrPeriodicStatsCallSetupCACMediaLimitFailure, csbCurrPeriodicStatsCallSetupCACMediaUpdateFailure, csbCurrPeriodicStatsTimestamp } STATUS current DESCRIPTION "A collection of objects providing current 5 minute statistics for Cisco Session border Controller (SBC)." ::= { csbCallStatsMIBGroups 3 } csbHistoryStatsGroup OBJECT-GROUP OBJECTS { csbHistoryStatsActiveCalls, csbHistoryStatsTotalCallAttempts, csbHistoryStatsFailedCallAttempts, csbHistoryStatsCallRoutingFailure, csbHistoryStatsCallResourceFailure, csbHistoryStatsCallMediaFailure, csbHistoryStatsFailSigFailure, csbHistoryStatsActiveCallFailure, csbHistoryStatsCongestionFailure, csbHistoryStatsCallSetupPolicyFailure, csbHistoryStatsCallSetupNAPolicyFailure, csbHistoryStatsCallSetupRoutingPolicyFailure, csbHistoryStatsCallSetupCACPolicyFailure, csbHistoryStatsCallSetupCACCallLimitFailure, csbHistoryStatsCallSetupCACRateLimitFailure, csbHistoryStatsCallSetupCACBandwidthFailure, csbHistoryStatsCallSetupCACMediaLimitFailure, csbHistoryStatsCallSetupCACMediaUpdateFailure, csbHistoryStatsTimestamp } STATUS current DESCRIPTION "A collection of objects providing previous 5 minute statistics for Cisco Session border Controller (SBC)." ::= { csbCallStatsMIBGroups 4 } csbPerFlowStatsGroup OBJECT-GROUP OBJECTS { csbPerFlowStatsRTPPktsRcvd, csbPerFlowStatsRTPPktsSent, csbPerFlowStatsRTPPktsDiscard, csbPerFlowStatsRTCPPktsSent, csbPerFlowStatsRTPOctetsRcvd, csbPerFlowStatsRTPOctetsSent, csbPerFlowStatsRTPOctetsDiscard, csbPerFlowStatsRTCPPktsRcvd, csbPerFlowStatsRTCPPktsLost, csbPerFlowStatsFlowType, csbPerFlowStatsTmanPerMbs, csbPerFlowStatsTmanPerSdr, csbPerFlowStatsDscpSettings, csbPerFlowStatsAdrStatus, csbPerFlowStatsQASettings, csbPerFlowStatsEPJitter } STATUS current DESCRIPTION "A collection of objects providing per flow statistics for Cisco Session border Controller (SBC)." ::= { csbCallStatsMIBGroups 5 } csbH248StatsGroup OBJECT-GROUP OBJECTS { csbH248StatsRequestsSent, csbH248StatsRequestsRcvd, csbH248StatsRequestsFailed, csbH248StatsRequestsRetried, csbH248StatsRepliesSent, csbH248StatsRepliesRcvd, csbH248StatsRepliesRetried, csbH248StatsSegPktsSent, csbH248StatsSegPktsRcvd, csbH248StatsTMaxTimeoutVal, csbH248StatsRTT, csbH248StatsLT, csbH248StatsEstablishedTime } STATUS deprecated DESCRIPTION "A collection of objects providing H.248 statistics for Cisco Session border Controller (SBC)." ::= { csbCallStatsMIBGroups 6 } csbH248StatsGroupRev1 OBJECT-GROUP OBJECTS { csbH248StatsRequestsSentRev1, csbH248StatsRequestsRcvdRev1, csbH248StatsRequestsFailedRev1, csbH248StatsRequestsRetriedRev1, csbH248StatsRepliesSentRev1, csbH248StatsRepliesRcvdRev1, csbH248StatsRepliesRetriedRev1, csbH248StatsSegPktsSentRev1, csbH248StatsSegPktsRcvdRev1, csbH248StatsEstablishedTimeRev1, csbH248StatsTMaxTimeoutValRev1, csbH248StatsRTTRev1, csbH248StatsLTRev1 } STATUS current DESCRIPTION "A collection of objects providing H.248 statistics for Cisco Session border Controller (SBC)." ::= { csbCallStatsMIBGroups 7 } csbGlobalStatsGroupSup1 OBJECT-GROUP OBJECTS { csbCallStatsAvailableTranscodeFlows, csbCallStatsActiveTranscodeFlows, csbCallStatsPeakTranscodeFlows, csbCallStatsTotalTranscodeFlows } STATUS current DESCRIPTION "A collection of objects providing global statistics for cisco Session border Controller (SBC)." ::= { csbCallStatsMIBGroups 8 } csbCurrPeriodicStatsGroupSup1 OBJECT-GROUP OBJECTS { csbCurrPeriodicStatsTranscodedCalls, csbCurrPeriodicStatsTransratedCalls, csbCurrPeriodicStatsTotalCallUpdateFailure, csbCurrPeriodicStatsActiveIpv6Calls, csbCurrPeriodicStatsActiveEmergencyCalls, csbCurrPeriodicStatsActiveE2EmergencyCalls, csbCurrPeriodicStatsImsRxActiveCalls, csbCurrPeriodicStatsImsRxCallSetupFaiures, csbCurrPeriodicStatsImsRxCallRenegotiationAttempts, csbCurrPeriodicStatsImsRxCallRenegotiationFailures, csbCurrPeriodicStatsAudioTranscodedCalls, csbCurrPeriodicStatsFaxTranscodedCalls, csbCurrPeriodicStatsRtpDisallowedFailures, csbCurrPeriodicStatsSrtpDisallowedFailures, csbCurrPeriodicStatsNonSrtpCalls, csbCurrPeriodicStatsSrtpNonIwCalls, csbCurrPeriodicStatsSrtpIwCalls, csbCurrPeriodicStatsDtmfIw2833Calls, csbCurrPeriodicStatsDtmfIwInbandCalls, csbCurrPeriodicStatsDtmfIw2833InbandCalls, csbCurrPeriodicStatsTotalTapsRequested, csbCurrPeriodicStatsTotalTapsSucceeded, csbCurrPeriodicStatsCurrentTaps, csbCurrPeriodicIpsecCalls } STATUS current DESCRIPTION "A collection of objects providing current 5 min, 15 min, 1 hour and 1 day statistics for Cisco Session border Controller (SBC)." ::= { csbCallStatsMIBGroups 9 } csbHistoryStatsGroupSup1 OBJECT-GROUP OBJECTS { csbHistroyStatsTranscodedCalls, csbHistroyStatsTransratedCalls, csbHistoryStatsTotalCallUpdateFailure, csbHistoryStatsActiveIpv6Calls, csbHistoryStatsActiveEmergencyCalls, csbHistoryStatsActiveE2EmergencyCalls, csbHistoryStatsImsRxActiveCalls, csbHistoryStatsImsRxCallSetupFailures, csbHistoryStatsImsRxCallRenegotiationAttempts, csbHistoryStatsImsRxCallRenegotiationFailures, csbHistoryStatsAudioTranscodedCalls, csbHistoryStatsFaxTranscodedCalls, csbHistoryStatsRtpDisallowedFailures, csbHistoryStatsSrtpDisallowedFailures, csbHistoryStatsNonSrtpCalls, csbHistoryStatsSrtpNonIwCalls, csbHistoryStatsSrtpIwCalls, csbHistoryStatsDtmfIw2833Calls, csbHistoryStatsDtmfIwInbandCalls, csbHistoryStatsDtmfIw2833InbandCalls, csbHistoryStatsTotalTapsRequested, csbHistoryStatsTotalTapsSucceeded, csbHistoryStatsCurrentTaps, csbHistoryStatsIpsecCalls } STATUS current DESCRIPTION "A collection of objects providing current 5 min, 15 min, 1 hour and 1 day statistics for Cisco Session border Controller (SBC)." ::= { csbCallStatsMIBGroups 10 } csbPerFlowStatsGroupSup1 OBJECT-GROUP OBJECTS { csbPerFlowStatsRTPPktsLost } STATUS current DESCRIPTION "A collection of objects providing per flow statistics for Cisco Session border Controller (SBC)." ::= { csbCallStatsMIBGroups 11 } END