-- ***************************************************************** -- CISCO-OPTICAL-MIB.my -- OPTICAL INTERFACE MIB -- -- June 2015 Aditi Gupta (aditigu) -- -- Copyright (c) 2015 by Cisco Systems, Inc. -- All rights reserved. -- ***************************************************************** CISCO-OPTICAL-MIB DEFINITIONS ::= BEGIN IMPORTS MODULE-IDENTITY, OBJECT-TYPE, NOTIFICATION-TYPE, Integer32, Unsigned32 FROM SNMPv2-SMI TEXTUAL-CONVENTION, TruthValue, DisplayString, MacAddress, TimeStamp FROM SNMPv2-TC MODULE-COMPLIANCE, OBJECT-GROUP, NOTIFICATION-GROUP FROM SNMPv2-CONF ifIndex, ifName FROM IF-MIB ciscoMgmt FROM CISCO-SMI; ciscoOpticalMIB MODULE-IDENTITY LAST-UPDATED "201605240000Z" ORGANIZATION "Cisco Systems, Inc." CONTACT-INFO "Cisco Systems Customer Service Postal: 170 W Tasman Drive San Jose, CA 95134 USA Tel: +1 800 553-NETS E-mail: cs-@cisco.com" DESCRIPTION "This MIB module defines the managed objects for physical layer characteristics of optical interfaces and performance statistics objects for protocol specific counters in optical devices. Performance monitoring (PM) parameters are used by service providers to gather, store, set thresholds for and report performance data for early detection of problems. Thresholds are used to set error levels for each PM parameter. During the accumulation cycle, if the current value of a performance monitoring parameter reaches or exceeds its corresponding threshold value, a threshold crossing alarm (TCA) is generated. The TCAs provide early detection of performance degradation. Glossary: LBC : Laser Bias Current TX : Transmit RX : Receive PMD : Polarization Mode Dispersion OSNR : Optical Signal to Noise Ratio DGD : Differential Group Delay CD : Chromatic Dispersion rad/s : radian per second dB : decibel dBm : decibel-milliwatt ps : picosecond nm : nanometer." REVISION "201605240000Z" DESCRIPTION "Added 1. Extend CoiIntervalType to include thirtySecond. 2. Extend coiOpticalControllerEntry to include coiOpticalControllerTotalRXPower, coiOpticalControllerTotalTXPower. 3. Add coiOpticalPowerGroup. 4. Deprecated the ciscoOpticalMIBCompliance compliance, added ciscoOpticalMIBComplianceRev1." REVISION "201512010000Z" DESCRIPTION "Added 1. NOTIFICATION-TYPE coiOpticalEquipmentAlarm 2. Textual Convention CoiOptAlarmType, CoiOptAlarmStatus, CoiOptAlarmSeverity, CoiOptAlarmServiceAffecting. 3. coiOpticalEquipmentAlarmGroup OBJECT INDENTIFIER, with coiOpticalAlarmLocation, coiOpticalAlarmType, coiOpticalAlarmTimeStamp, coiOpticalAlarmName, coiOpticalAlarmAdditionalInfo, coiOpticalAlarmSeverity, coiOpticalAlarmStatus, coiOpticalAlarmServiceAffecting as OBJECT-TYPE. 4. ppmFail bit for coiOpticalControllerStatus." REVISION "201510300000Z" DESCRIPTION "Initial version of this MIB module." ::= { ciscoMgmt 828 } CoiOpticalPower ::= TEXTUAL-CONVENTION STATUS current DESCRIPTION "This value indicates the optical receive or transmit power." SYNTAX Integer32 (-4000..3000) CoiOpticalWavelength ::= TEXTUAL-CONVENTION STATUS current DESCRIPTION "This value represents the wavelength of optical signals, in an optical interface. It is represented in units of nanometers. A value of zero either indicates that the wavelength is unknown, or that it does not fall under the frequency grid defined in ITU-T G.694.1" REFERENCE "ITU - T Recommendation G.694.1 - Spectral grids for WDM applications: DWDM frequency grid, May 2002" SYNTAX Unsigned32 (0 | 1528770..1604030) CoiIntervalType ::= TEXTUAL-CONVENTION STATUS current DESCRIPTION "This value indicates the time period over which performance monitoring data has been collected. Valid values are - fifteenMin(1) - values for the 15 min interval. oneDay(2) - values for the 1 Day interval. thirtySecond(3)- values for the 30 Sec interval." SYNTAX INTEGER { fifteenMin(1), oneDay(2), thirtySecond(3) } CoiPortType ::= TEXTUAL-CONVENTION STATUS current DESCRIPTION "This value indicates the port type of the optical interface. Valid values are - clientPort(1) - denotes client port. trunkPort(2) - denotes trunk port." SYNTAX INTEGER { clientPort(1), trunkPort(2) } CoiOptAlarmType ::= TEXTUAL-CONVENTION STATUS current DESCRIPTION "This value indicates the alarm type. alarmUnknown(1) - denotes unknown alarm type. equipmentFailure(2) - denotes equipment fail alarm type." SYNTAX INTEGER { alarmUnknown(1), equipmentFailure(2) } CoiOptAlarmSeverity ::= TEXTUAL-CONVENTION STATUS current DESCRIPTION "This will indicate the severity of the notification being sent out. Valid values are - notReported(1) - alarm not reported. notAlarmed(2) - alarm not raised. minor(3) - minor alarm. major(4) - major alarm. critical(5) - critical alarm." SYNTAX INTEGER { notReported(1), notAlarmed(2), minor(3), major(4), critical(5) } CoiOptAlarmStatus ::= TEXTUAL-CONVENTION STATUS current DESCRIPTION "This will indicate the status of the alarm. Valid values are - raised(1) - alarm in raised state. cleared(2) - alarm in cleared state. transient(3)- alarm in transient state." SYNTAX INTEGER { raised(1), cleared(2), transient(3) } CoiOptAlarmServiceAffecting ::= TEXTUAL-CONVENTION STATUS current DESCRIPTION "This will indicate the sevice-affecting state of the alarm. Valid values are - Service affecting(1) - alarm affects service. Non-Service affecting(2)- alarm does not affect service." SYNTAX INTEGER { serviceAffecting(1), nonServiceAffecting(2) } -- Textual Conventions definition will be defined before this line ciscoOpticalMIBNotifs OBJECT IDENTIFIER ::= { ciscoOpticalMIB 0 } ciscoOpticalMIBObjects OBJECT IDENTIFIER ::= { ciscoOpticalMIB 1 } coiOpticsStatusChange NOTIFICATION-TYPE OBJECTS { ifIndex, ifName, coiOpticalControllerPortType, coiOpticalControllerStatus } STATUS current DESCRIPTION "This notification is generated whenever the defect status of Optics on an interface changes. Varbind 'ifIndex' indicates the interface whose defect status of the Optics layer has just changed. Varbind 'ifName' indicates the interface Name whose defect status of the Optics layer has just changed. Varbind 'coiOpticalControllerPortType' indicates the port type of the interface whose defect status of the Optics layer has just changed. Varbind 'coiOpticalControllerStatus' indicates the current defect status of the Optics layer on the interface." ::= { ciscoOpticalMIBNotifs 1 } coiOpticalEquipmentAlarm NOTIFICATION-TYPE OBJECTS { coiOpticalAlarmLocation, coiOpticalAlarmType, coiOpticalAlarmTimeStamp, coiOpticalAlarmName, coiOpticalAlarmAdditionalInfo, coiOpticalAlarmSeverity, coiOpticalAlarmStatus, coiOpticalAlarmServiceAffecting } STATUS current DESCRIPTION "This notification is generated whenever the optical equipment alarm is generated. Varbind 'coiOpticalAlarmLocation' indicates the location on which equipment failed alarm has generated. Varbind 'coiOpticalAlarmType' indicates the type of alarm. Varbind 'coiOpticalAlarmTimeStamp' indicates the timestamp when alarm is generated. Varbind 'coiOpticalAlarmName' indicates the alarm object. Varbind 'coiOpticalAlarmAdditionalInfo' indicates additional info related to the alarm. Varbind 'coiOpticalAlarmSeverity' indicates the severity of the alarm. Varbind 'coiOpticalAlarmStatus' indicates status of the alarm. Varbind 'coiOpticalAlarmServiceAffecting' indicates the service affected state when alarm is generated." ::= { ciscoOpticalMIBNotifs 2 } coiOpticalController OBJECT IDENTIFIER ::= { ciscoOpticalMIBObjects 1 } coiOpticalPerformanceMonitoring OBJECT IDENTIFIER ::= { ciscoOpticalMIBObjects 2 } coiOpticalNotifEnabled OBJECT-TYPE SYNTAX TruthValue MAX-ACCESS read-write STATUS current DESCRIPTION "This object controls the generation of coiOpticsStatusChange notification. If the value of this object is 'true', then the generation of coiOpticsStatusChange notification is enabled. If the value of this object is 'false', then the generation of coiOpticsStatusChange notification is disabled." ::= { coiOpticalController 1 } coiOpticalControllerTable OBJECT-TYPE SYNTAX SEQUENCE OF CoiOpticalControllerEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "This table provides management information for optical layer related attributes of interfaces with an ifType of opticalChannel(195)." ::= { coiOpticalController 2 } coiOpticalControllerEntry OBJECT-TYPE SYNTAX CoiOpticalControllerEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "An entry containing management information on optical layer related attributes of interfaces with an ifType opticalChannel(195). Entries are created by the feature when a new interface is added to the ifTable." INDEX { ifIndex } ::= { coiOpticalControllerTable 1 } CoiOpticalControllerEntry ::= SEQUENCE { coiOpticalControllerWavelength CoiOpticalWavelength, coiOpticalControllerLaserStatus INTEGER, coiOpticalControllerFrequency Unsigned32, coiOpticalControllerChannelNumber Unsigned32, coiOpticalControllerTransmitPower CoiOpticalPower, coiOpticalControllerOpticsType DisplayString, coiOpticalControllerRXLowThreshold CoiOpticalPower, coiOpticalControllerTXLowThreshold CoiOpticalPower, coiOpticalControllerRXHighThreshold CoiOpticalPower, coiOpticalControllerTXHighThreshold CoiOpticalPower, coiOpticalControllerLBCHighThreshold Integer32, coiOpticalControllerStatus BITS, coiOpticalControllerPortType CoiPortType, coiOpticalControllerTotalRXPower CoiOpticalPower, coiOpticalControllerTotalTXPower CoiOpticalPower } coiOpticalControllerWavelength OBJECT-TYPE SYNTAX CoiOpticalWavelength UNITS "1/100 nm" MAX-ACCESS read-write STATUS current DESCRIPTION "This object is used to configure the wavelength on optical channel interfaces in 1/100 nm." DEFVAL { 1529553 } ::= { coiOpticalControllerEntry 1 } coiOpticalControllerLaserStatus OBJECT-TYPE SYNTAX INTEGER { up(1), down(2) } MAX-ACCESS read-only STATUS current DESCRIPTION "This object gives the current operational state of the Laser. Valid values are - 'up' - The laser is operational. 'down' - The laser is not operational." ::= { coiOpticalControllerEntry 2 } coiOpticalControllerFrequency OBJECT-TYPE SYNTAX Unsigned32 UNITS "100 MHz" MAX-ACCESS read-write STATUS current DESCRIPTION "This object is used to configure the frequency on optical channel interfaces in 100 MHz." ::= { coiOpticalControllerEntry 3 } coiOpticalControllerChannelNumber OBJECT-TYPE SYNTAX Unsigned32 MAX-ACCESS read-write STATUS current DESCRIPTION "This object is used to configure the channel number on optical channel interfaces. Channel Number is set to 0 if not 50GHz grid." ::= { coiOpticalControllerEntry 4 } coiOpticalControllerTransmitPower OBJECT-TYPE SYNTAX CoiOpticalPower UNITS "1/100 dBm" MAX-ACCESS read-write STATUS current DESCRIPTION "This object is used to configure the Transmit Power in 1/100 dBm on optical channel interfaces." ::= { coiOpticalControllerEntry 5 } coiOpticalControllerOpticsType OBJECT-TYPE SYNTAX DisplayString MAX-ACCESS read-only STATUS current DESCRIPTION "This object gives the description of optics present on optical channel interfaces." ::= { coiOpticalControllerEntry 6 } coiOpticalControllerRXLowThreshold OBJECT-TYPE SYNTAX CoiOpticalPower UNITS "1/100 dBm" MAX-ACCESS read-write STATUS current DESCRIPTION "This object is used to configure the Receive Low Threshold in 1/100 dBm on optical channel interfaces." ::= { coiOpticalControllerEntry 7 } coiOpticalControllerTXLowThreshold OBJECT-TYPE SYNTAX CoiOpticalPower UNITS "1/100 dBm" MAX-ACCESS read-write STATUS current DESCRIPTION "This object is used to configure the Transmit Low Threshold in 1/100 dBm on optical channel interfaces." ::= { coiOpticalControllerEntry 8 } coiOpticalControllerRXHighThreshold OBJECT-TYPE SYNTAX CoiOpticalPower UNITS "1/100 dBm" MAX-ACCESS read-write STATUS current DESCRIPTION "This object is used to configure the Receive High Threshold in 1/100 dBm on optical channel interfaces." ::= { coiOpticalControllerEntry 9 } coiOpticalControllerTXHighThreshold OBJECT-TYPE SYNTAX CoiOpticalPower UNITS "1/100 dBm" MAX-ACCESS read-write STATUS current DESCRIPTION "This object is used to configure the Transmit High Threshold in 1/100 dBm on optical channel interfaces." ::= { coiOpticalControllerEntry 10 } coiOpticalControllerLBCHighThreshold OBJECT-TYPE SYNTAX Integer32 (0..1000) UNITS "1/10 %" MAX-ACCESS read-write STATUS current DESCRIPTION "This object is used to configure the Laser Bias Current High Threshold in 1/10% on optical channel interfaces." ::= { coiOpticalControllerEntry 11 } coiOpticalControllerStatus OBJECT-TYPE SYNTAX BITS { noDefect(0), improprmvl(1), mea(2), provMismatch(3), highRXPwr(4), highTXPwr(5), lowRXPwr(6), lowTXPwr(7), highLBC(8), highDGD(9), outOfRangeCD(10), lowOSNR(11), wvlOutOfLock(12), highLaserTemp(13), lowLaserTemp(14), ppmFail(15) } MAX-ACCESS read-only STATUS current DESCRIPTION "This object indicates the current defect status of the Optics layer. noDefect(0): No Defect. This bit is set high when no defect is detected on the optics. improprmvl(1): Improper Removal. This will be set when a physical pluggable is absent on a service (hw-module) provisioned port. mea(2): This bit will be set when Port Pluggable Module Mismatches With Pre-Provisoned PPM. provMismatch(3): Provision Mismatch. This bit is set when Provisioned wavelength is Not supported By Pluggable. highRXPwr(4): High Receive Power. This bit is set when the measured optical power of the received signal exceeds the threshold high value, which is user-provisionable. highTXPwr(5): High Transmit Power. This bit is set when Pluggable measured optical power of the transmitted signal falls over the threshold. lowRXPwr(6): Low Receive Power. This bit is set when the measured optical power of the received signal falls below the low threshold value, which is user-provisionable. lowTXPwr(7): Low Transmit Power. This bit is set when Pluggable measured optical power of the transmitted signal falls below the low threshold. highLBC(8): High Laser Bias. This bit is set when the Physical Pluggable Port laser reads laser bias value beyond configured high threshold. highDGD(9): High DGD. This bit is set when the pluggable port Module reads the Differential Group delay value that exceeds the configured high threshold. outOfRangeCD(10): Out of Range Chromatic Dispersion. This bit is set when the Chromatic dispersion value read by the associated HW is out of range with the configured threshold. lowOSNR(11): Low Optical Signal to Noise Ratio. This bit is set when the HW read Optical Signal to Noise ratio falls below the configured low threshold. wvlOutOfLock(12): Wavelength Out of Lock. This bit is set when Trunk Port optics detects that optical input frequency is out of range. highLaserTemp(13): High LaserTemp.This bit is set when the internally measured transceiver temperature exceeds the card setting by 35.6 degrees F or 2 degrees C. A laser temperature change affects the transmitted wavelength. lowLaserTemp(14): Low LaserTemp. This bit is set when the internally measured transceiver temperature falls below the card setting by 35.6 degrees F or 2 degrees C. A laser temperature change affects the transmitted wavelength. (This temperature is equivalent to about 200 picometers of wavelength. ppmFail(15): Pluggable Equipment Fail. This bit is set when Pluggable Equipment is not operational or manageable. This object is sent out as a notification to the agent." ::= { coiOpticalControllerEntry 12 } coiOpticalControllerPortType OBJECT-TYPE SYNTAX CoiPortType MAX-ACCESS read-only STATUS current DESCRIPTION "This object gives the port type of the optical interface." ::= { coiOpticalControllerEntry 13 } coiOpticalControllerTotalRXPower OBJECT-TYPE SYNTAX CoiOpticalPower UNITS "1/100 dBm" MAX-ACCESS read-write STATUS current DESCRIPTION "This object is used to configure the total receive power in 1/100 dBm on optical channel interfaces." ::= { coiOpticalControllerEntry 14 } coiOpticalControllerTotalTXPower OBJECT-TYPE SYNTAX CoiOpticalPower UNITS "1/100 dBm" MAX-ACCESS read-write STATUS current DESCRIPTION "This object is used to configure the total transmit power in 1/100 dBm on optical channel interfaces." ::= { coiOpticalControllerEntry 15 } coiOpticalControllerPerLaneTable OBJECT-TYPE SYNTAX SEQUENCE OF CoiOpticalControllerPerLaneEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "This table provides the management information for optical layer related attributes of interfaces with an ifType of opticalChannel(195) and lane number as coiOpticalControllerLane." ::= { coiOpticalController 3 } coiOpticalControllerPerLaneEntry OBJECT-TYPE SYNTAX CoiOpticalControllerPerLaneEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "An entry containing management information on optical layer related attributes of interfaces with an ifType opticalChannel(195) and lane number as coiOpticalControllerLane. Entries are created by the feature when a new interface is added to the ifTable." INDEX { ifIndex, coiOpticalControllerLane } ::= { coiOpticalControllerPerLaneTable 1 } CoiOpticalControllerPerLaneEntry ::= SEQUENCE { coiOpticalControllerLane Integer32, coiOpticalControllerPerLaneRXPower CoiOpticalPower, coiOpticalControllerPerLaneTXPower CoiOpticalPower, coiOpticalControllerPerLaneLBC Integer32, coiOpticalControllerPerLaneOSNR Integer32, coiOpticalControllerPerLaneChromaticDispersion Integer32, coiOpticalControllerPerLaneDifferentialGroupDelay Integer32, coiOpticalControllerPerLaneSecondOrderPMD Integer32, coiOpticalControllerPerLanePolarizationDependentLoss Integer32, coiOpticalControllerPerLanePolarizationChangeRate Integer32, coiOpticalControllerPerLanePhaseNoise Integer32 } coiOpticalControllerLane OBJECT-TYPE SYNTAX Integer32 (1..12) MAX-ACCESS not-accessible STATUS current DESCRIPTION "This object specifies the lane number for the optical controller. Each optical controller is divided into data lanes, with each lane operating at some data rate, giving an aggregated bandwidth of the controller, as a whole. Lane is applicable for breakout mode of operation." ::= { coiOpticalControllerPerLaneEntry 1 } coiOpticalControllerPerLaneRXPower OBJECT-TYPE SYNTAX CoiOpticalPower UNITS "1/100 dBm" MAX-ACCESS read-only STATUS current DESCRIPTION "This object specifies the Receive power in 1/100 dBm." ::= { coiOpticalControllerPerLaneEntry 2 } coiOpticalControllerPerLaneTXPower OBJECT-TYPE SYNTAX CoiOpticalPower UNITS "1/100 dBm" MAX-ACCESS read-only STATUS current DESCRIPTION "This object specifies the Transmit power in 1/100 dBm." ::= { coiOpticalControllerPerLaneEntry 3 } coiOpticalControllerPerLaneLBC OBJECT-TYPE SYNTAX Integer32 (0..1000) UNITS "1/10 %" MAX-ACCESS read-only STATUS current DESCRIPTION "This object specifies the Laser Bias Current in 1/10%." ::= { coiOpticalControllerPerLaneEntry 4 } coiOpticalControllerPerLaneOSNR OBJECT-TYPE SYNTAX Integer32 UNITS "1/100 dB" MAX-ACCESS read-only STATUS current DESCRIPTION "This object specifies the Optical Signal to Noise Ratio in 1/100 dB." ::= { coiOpticalControllerPerLaneEntry 5 } coiOpticalControllerPerLaneChromaticDispersion OBJECT-TYPE SYNTAX Integer32 UNITS "ps/nm" MAX-ACCESS read-only STATUS current DESCRIPTION "This object specifies the measure of spread of light pulse in ps/nm." ::= { coiOpticalControllerPerLaneEntry 6 } coiOpticalControllerPerLaneDifferentialGroupDelay OBJECT-TYPE SYNTAX Integer32 UNITS "1/100 ps" MAX-ACCESS read-only STATUS current DESCRIPTION "This object specifies the propagation time difference between eigenmodes X and Y in 1/100 ps." ::= { coiOpticalControllerPerLaneEntry 7 } coiOpticalControllerPerLaneSecondOrderPMD OBJECT-TYPE SYNTAX Integer32 UNITS "1/100 ps^2" MAX-ACCESS read-only STATUS current DESCRIPTION "This object specifies the threshold Second Order Polarization Mode Dispersion in 1/100 ps^2." ::= { coiOpticalControllerPerLaneEntry 8 } coiOpticalControllerPerLanePolarizationDependentLoss OBJECT-TYPE SYNTAX Integer32 UNITS "1/100 dB" MAX-ACCESS read-only STATUS current DESCRIPTION "This object specifies the threshold Polarization Dependent Loss in 1/100 dB." ::= { coiOpticalControllerPerLaneEntry 9 } coiOpticalControllerPerLanePolarizationChangeRate OBJECT-TYPE SYNTAX Integer32 UNITS "1/100 rad/s" MAX-ACCESS read-only STATUS current DESCRIPTION "This object specifies the Polarization Change Rate in 1/100 rad/s." ::= { coiOpticalControllerPerLaneEntry 10 } coiOpticalControllerPerLanePhaseNoise OBJECT-TYPE SYNTAX Integer32 UNITS "1/1000 dB" MAX-ACCESS read-only STATUS current DESCRIPTION "This object specifies the Fluctuations in the Phase of a Waveform in 1/1000 dB." ::= { coiOpticalControllerPerLaneEntry 11 } coiOpticalClientInfoTable OBJECT-TYPE SYNTAX SEQUENCE OF CoiOpticalClientInfoEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "This table provides management information for optical's client layer related attributes of interfaces with an ifType of ethernetCsmacd(6).This parameter is applicable only for client interfaces." ::= { ciscoOpticalMIBObjects 3 } coiOpticalClientInfoEntry OBJECT-TYPE SYNTAX CoiOpticalClientInfoEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "An entry containing information for optical's client layer related attributes of interfaces with an ifType of ethernetCsmacd(6). Entries are created by the feature when the interface discovers the neighbour's ethernet MAC Address." INDEX { ifIndex } ::= { coiOpticalClientInfoTable 1 } CoiOpticalClientInfoEntry ::= SEQUENCE { coiOpticalClientEthernetNeighbourMAC MacAddress } coiOpticalClientEthernetNeighbourMAC OBJECT-TYPE SYNTAX MacAddress MAX-ACCESS read-only STATUS current DESCRIPTION "This object gives the neighbour MAC Address to which the interface is connected." ::= { coiOpticalClientInfoEntry 1 } coiOpticalThresholdTable OBJECT-TYPE SYNTAX SEQUENCE OF CoiOpticalThresholdEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "This table provides threshold information for optical layer related attributes of interfaces with an ifType of opticalChannel(195) and Interval type as coiOptThreshIntervalType." ::= { coiOpticalPerformanceMonitoring 1 } coiOpticalThresholdEntry OBJECT-TYPE SYNTAX CoiOpticalThresholdEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "An entry containing threshold information on optical layer related attributes of interfaces with an ifType opticalChannel(195). Entries are created by the feature when a new interface is added to the ifTable." INDEX { ifIndex, coiOptThreshIntervalType } ::= { coiOpticalThresholdTable 1 } CoiOpticalThresholdEntry ::= SEQUENCE { coiOptThreshIntervalType CoiIntervalType, coiOptThreshTXPowerMin CoiOpticalPower, coiOptThreshRXPowerMin CoiOpticalPower, coiOptThreshOSNRMin Integer32, coiOptThreshChromaticDispersionMin Integer32, coiOptThreshDifferentialGroupDelayMin Integer32, coiOptThreshSecondOrderPMDMin Integer32, coiOptThreshPolarizationDependentLossMin Integer32, coiOptThreshPolarizationChangeRateMin Integer32, coiOptThreshPhaseNoiseMin Integer32, coiOptThreshLBCMin Integer32, coiOptThreshTXPowerMax CoiOpticalPower, coiOptThreshRXPowerMax CoiOpticalPower, coiOptThreshOSNRMax Integer32, coiOptThreshChromaticDispersionMax Integer32, coiOptThreshDifferentialGroupDelayMax Integer32, coiOptThreshSecondOrderPMDMax Integer32, coiOptThreshPolarizationDependentLossMax Integer32, coiOptThreshPolarizationChangeRateMax Integer32, coiOptThreshPhaseNoiseMax Integer32, coiOptThreshLBCMax Integer32, coiOptThreshTXPowerEnableMin TruthValue, coiOptThreshRXPowerEnableMin TruthValue, coiOptThreshOSNREnableMin TruthValue, coiOptThreshChromaticDispersionEnableMin TruthValue, coiOptThreshDifferentialGroupDelayEnableMin TruthValue, coiOptThreshSecondOrderPMDEnableMin TruthValue, coiOptThreshPolarizationDependentLossEnableMin TruthValue, coiOptThreshPolarizationChangeRateEnableMin TruthValue, coiOptThreshPhaseNoiseEnableMin TruthValue, coiOptThreshLBCEnableMin TruthValue, coiOptThreshTXPowerEnableMax TruthValue, coiOptThreshRXPowerEnableMax TruthValue, coiOptThreshOSNREnableMax TruthValue, coiOptThreshChromaticDispersionEnableMax TruthValue, coiOptThreshDifferentialGroupDelayEnableMax TruthValue, coiOptThreshSecondOrderPMDEnableMax TruthValue, coiOptThreshPolarizationDependentLossEnableMax TruthValue, coiOptThreshPolarizationChangeRateEnableMax TruthValue, coiOptThreshPhaseNoiseEnableMax TruthValue, coiOptThreshLBCEnableMax TruthValue } coiOptThreshIntervalType OBJECT-TYPE SYNTAX CoiIntervalType MAX-ACCESS not-accessible STATUS current DESCRIPTION "This object gives the interval type during which the performance statistics are accumulated for the interface." ::= { coiOpticalThresholdEntry 1 } coiOptThreshTXPowerMin OBJECT-TYPE SYNTAX CoiOpticalPower UNITS "1/100 dBm" MAX-ACCESS read-write STATUS current DESCRIPTION "This object is used to configure the threshold of minimum Transmit power for the interface in 1/100 dBm." ::= { coiOpticalThresholdEntry 2 } coiOptThreshRXPowerMin OBJECT-TYPE SYNTAX CoiOpticalPower UNITS "1/100 dBm" MAX-ACCESS read-write STATUS current DESCRIPTION "This object is used to configure the threshold of minimum Receive power for the interface in 1/100 dBm." ::= { coiOpticalThresholdEntry 3 } coiOptThreshOSNRMin OBJECT-TYPE SYNTAX Integer32 UNITS "1/100 dB" MAX-ACCESS read-write STATUS current DESCRIPTION "This object is used to configure the threshold of minimum Optical Signal to Noise Ratio for the interface in 1/100 dB." ::= { coiOpticalThresholdEntry 4 } coiOptThreshChromaticDispersionMin OBJECT-TYPE SYNTAX Integer32 UNITS "ps/nm" MAX-ACCESS read-write STATUS current DESCRIPTION "This object is used to configure the threshold of minimum measure of spread of light pulse for the interface in ps/nm." ::= { coiOpticalThresholdEntry 5 } coiOptThreshDifferentialGroupDelayMin OBJECT-TYPE SYNTAX Integer32 UNITS "1/100 ps" MAX-ACCESS read-write STATUS current DESCRIPTION "This object is used to configure the threshold of minimum propagation time difference between eigenmodes X and Y for the interface in 1/100 ps." ::= { coiOpticalThresholdEntry 6 } coiOptThreshSecondOrderPMDMin OBJECT-TYPE SYNTAX Integer32 UNITS "1/100 ps^2" MAX-ACCESS read-write STATUS current DESCRIPTION "This object is used to configure the threshold of minimum Second Order Polarization Mode Dispersion for the interface in 1/100 ps^2." ::= { coiOpticalThresholdEntry 7 } coiOptThreshPolarizationDependentLossMin OBJECT-TYPE SYNTAX Integer32 UNITS "1/100 dB" MAX-ACCESS read-write STATUS current DESCRIPTION "This object is used to configure the threshold of minimum Polarization Dependent Loss for the interface in 1/100 dB." ::= { coiOpticalThresholdEntry 8 } coiOptThreshPolarizationChangeRateMin OBJECT-TYPE SYNTAX Integer32 UNITS "1/100 rad/s" MAX-ACCESS read-write STATUS current DESCRIPTION "This object is used to configure the threshold of minimum Polarization Change Rate for the interface in 1/100 rad/s." ::= { coiOpticalThresholdEntry 9 } coiOptThreshPhaseNoiseMin OBJECT-TYPE SYNTAX Integer32 UNITS "1/1000 dB" MAX-ACCESS read-write STATUS current DESCRIPTION "This object is used to configure the threshold of minimum Fluctuations in the Phase of a Waveform for the interface in 1/1000 dB." ::= { coiOpticalThresholdEntry 10 } coiOptThreshLBCMin OBJECT-TYPE SYNTAX Integer32 (0..1000) UNITS "1/10 %" MAX-ACCESS read-write STATUS current DESCRIPTION "This object is used to configure the threshold of minumum Laser Bias Current in 1/10%." ::= { coiOpticalThresholdEntry 11 } coiOptThreshTXPowerMax OBJECT-TYPE SYNTAX CoiOpticalPower UNITS "1/100 dBm" MAX-ACCESS read-write STATUS current DESCRIPTION "This object is used to configure the threshold of maximum Transmit power for the interface in 1/100 dBm." ::= { coiOpticalThresholdEntry 12 } coiOptThreshRXPowerMax OBJECT-TYPE SYNTAX CoiOpticalPower UNITS "1/100 dBm" MAX-ACCESS read-write STATUS current DESCRIPTION "This object is used to configure the threshold of maximum Receive power for the interface in 1/100 dBm." ::= { coiOpticalThresholdEntry 13 } coiOptThreshOSNRMax OBJECT-TYPE SYNTAX Integer32 UNITS "1/100 dB" MAX-ACCESS read-write STATUS current DESCRIPTION "This object is used to configure the threshold of maximum Optical Signal to Noise Ratio for the interface in 1/100 dB." ::= { coiOpticalThresholdEntry 14 } coiOptThreshChromaticDispersionMax OBJECT-TYPE SYNTAX Integer32 UNITS "ps/nm" MAX-ACCESS read-write STATUS current DESCRIPTION "This object is used to configure the threshold of maximum measure of spread of light pulse for the interface in ps/nm." ::= { coiOpticalThresholdEntry 15 } coiOptThreshDifferentialGroupDelayMax OBJECT-TYPE SYNTAX Integer32 UNITS "1/100 ps" MAX-ACCESS read-write STATUS current DESCRIPTION "This object is used to configure the threshold of maximum propagation time difference between eigenmodes X and Y for the interface in 1/100 ps." ::= { coiOpticalThresholdEntry 16 } coiOptThreshSecondOrderPMDMax OBJECT-TYPE SYNTAX Integer32 UNITS "1/100 ps^2" MAX-ACCESS read-write STATUS current DESCRIPTION "This object is used to configure the threshold of maximum Second Order Polarization Mode Dispersion for the interface in 1/100 ps^2." ::= { coiOpticalThresholdEntry 17 } coiOptThreshPolarizationDependentLossMax OBJECT-TYPE SYNTAX Integer32 UNITS "1/100 dB" MAX-ACCESS read-write STATUS current DESCRIPTION "This object is used to configure the threshold of maximum Polarization Dependent Loss for the interface in 1/100 dB." ::= { coiOpticalThresholdEntry 18 } coiOptThreshPolarizationChangeRateMax OBJECT-TYPE SYNTAX Integer32 UNITS "1/100 rad/s" MAX-ACCESS read-write STATUS current DESCRIPTION "This object is used to configure the threshold of maximum Polarization Change Rate in 1/100 rad/s for the interface." ::= { coiOpticalThresholdEntry 19 } coiOptThreshPhaseNoiseMax OBJECT-TYPE SYNTAX Integer32 UNITS "1/1000 dB" MAX-ACCESS read-write STATUS current DESCRIPTION "This object is used to configure the threshold of maximum Fluctuations in the Phase of a Waveform in 1/1000 dB for the interface." ::= { coiOpticalThresholdEntry 20 } coiOptThreshLBCMax OBJECT-TYPE SYNTAX Integer32 (0..1000) UNITS "1/10 %" MAX-ACCESS read-write STATUS current DESCRIPTION "This object is used to configure the threshold of maximum Laser Bias Current in 1/10 % for the interface." ::= { coiOpticalThresholdEntry 21 } coiOptThreshTXPowerEnableMin OBJECT-TYPE SYNTAX TruthValue MAX-ACCESS read-write STATUS current DESCRIPTION "This object is used to configure the enablement of threshold min Transmit power for the interface." ::= { coiOpticalThresholdEntry 22 } coiOptThreshRXPowerEnableMin OBJECT-TYPE SYNTAX TruthValue MAX-ACCESS read-write STATUS current DESCRIPTION "This object is used to configure the enablement of the threshold min Receive power for the interface." ::= { coiOpticalThresholdEntry 23 } coiOptThreshOSNREnableMin OBJECT-TYPE SYNTAX TruthValue MAX-ACCESS read-write STATUS current DESCRIPTION "This object is used to configure the enablement of the threshold min Optical Signal to Noise Ratio for the interface." ::= { coiOpticalThresholdEntry 24 } coiOptThreshChromaticDispersionEnableMin OBJECT-TYPE SYNTAX TruthValue MAX-ACCESS read-write STATUS current DESCRIPTION "This object is used to configure the enablement of the threshold min measure of spread of light pulse for the interface." ::= { coiOpticalThresholdEntry 25 } coiOptThreshDifferentialGroupDelayEnableMin OBJECT-TYPE SYNTAX TruthValue MAX-ACCESS read-write STATUS current DESCRIPTION "This object is used to configure the enablement of the threshold min propagation time difference between eigenmodes X and Y for the interface." ::= { coiOpticalThresholdEntry 26 } coiOptThreshSecondOrderPMDEnableMin OBJECT-TYPE SYNTAX TruthValue MAX-ACCESS read-write STATUS current DESCRIPTION "This object is used to configure the enablement of the threshold min Second Order Polarization Mode Dispersion for the interface." ::= { coiOpticalThresholdEntry 27 } coiOptThreshPolarizationDependentLossEnableMin OBJECT-TYPE SYNTAX TruthValue MAX-ACCESS read-write STATUS current DESCRIPTION "This object is used to configure the enablement of the threshold min Polarization Dependent Loss for the interface." ::= { coiOpticalThresholdEntry 28 } coiOptThreshPolarizationChangeRateEnableMin OBJECT-TYPE SYNTAX TruthValue MAX-ACCESS read-write STATUS current DESCRIPTION "This object is used to configure the enablement of the threshold min Polarization Change Rate for the interface." ::= { coiOpticalThresholdEntry 29 } coiOptThreshPhaseNoiseEnableMin OBJECT-TYPE SYNTAX TruthValue MAX-ACCESS read-write STATUS current DESCRIPTION "This object is used to configure the enablement of the threshold min Fluctuations in the Phase of a Waveform for the interface." ::= { coiOpticalThresholdEntry 30 } coiOptThreshLBCEnableMin OBJECT-TYPE SYNTAX TruthValue MAX-ACCESS read-write STATUS current DESCRIPTION "This object is used to configure the enablement of the threshold min Laser Bias Current for the interface." ::= { coiOpticalThresholdEntry 31 } coiOptThreshTXPowerEnableMax OBJECT-TYPE SYNTAX TruthValue MAX-ACCESS read-write STATUS current DESCRIPTION "This object is used to configure the enablement of the threshold max Transmit power for the interface." ::= { coiOpticalThresholdEntry 32 } coiOptThreshRXPowerEnableMax OBJECT-TYPE SYNTAX TruthValue MAX-ACCESS read-write STATUS current DESCRIPTION "This object is used to configure the enablement of the threshold max Receive power for the interface." ::= { coiOpticalThresholdEntry 33 } coiOptThreshOSNREnableMax OBJECT-TYPE SYNTAX TruthValue MAX-ACCESS read-write STATUS current DESCRIPTION "This object is used to configure the enablement of the threshold max Optical Signal to Noise Ratio for the interface." ::= { coiOpticalThresholdEntry 34 } coiOptThreshChromaticDispersionEnableMax OBJECT-TYPE SYNTAX TruthValue MAX-ACCESS read-write STATUS current DESCRIPTION "This object is used to configure the enablement of the threshold max measure of spread of light pulse for the interface." ::= { coiOpticalThresholdEntry 35 } coiOptThreshDifferentialGroupDelayEnableMax OBJECT-TYPE SYNTAX TruthValue MAX-ACCESS read-write STATUS current DESCRIPTION "This object is used to configure the enablement of the threshold max propagation time difference between eigenmodes X and Y for the interface." ::= { coiOpticalThresholdEntry 36 } coiOptThreshSecondOrderPMDEnableMax OBJECT-TYPE SYNTAX TruthValue MAX-ACCESS read-write STATUS current DESCRIPTION "This object is used to configure the enablement of the threshold max Second Order Polarization Mode Dispersion for the interface." ::= { coiOpticalThresholdEntry 37 } coiOptThreshPolarizationDependentLossEnableMax OBJECT-TYPE SYNTAX TruthValue MAX-ACCESS read-write STATUS current DESCRIPTION "This object is used to configure the enablement of the threshold max Polarization Dependent Loss for the interface." ::= { coiOpticalThresholdEntry 38 } coiOptThreshPolarizationChangeRateEnableMax OBJECT-TYPE SYNTAX TruthValue MAX-ACCESS read-write STATUS current DESCRIPTION "This object is used to configure the enablement of the threshold max Polarization Change Rate for the interface." ::= { coiOpticalThresholdEntry 39 } coiOptThreshPhaseNoiseEnableMax OBJECT-TYPE SYNTAX TruthValue MAX-ACCESS read-write STATUS current DESCRIPTION "This object is used to configure the enablement of the threshold max Fluctuations in the Phase of a Waveform for the interface." ::= { coiOpticalThresholdEntry 40 } coiOptThreshLBCEnableMax OBJECT-TYPE SYNTAX TruthValue MAX-ACCESS read-write STATUS current DESCRIPTION "This object is used to configure the enablement of the threshold max Laser Bias Current for the interface." ::= { coiOpticalThresholdEntry 41 } coiOpticalCurrentTable OBJECT-TYPE SYNTAX SEQUENCE OF CoiOpticalCurrentEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "This table provides current information for optical layer related attributes of interfaces with an ifType of opticalChannel(195), Lane as coiOptCurrentLane and Interval as coiOptCurrentIntervalType." ::= { coiOpticalPerformanceMonitoring 2 } coiOpticalCurrentEntry OBJECT-TYPE SYNTAX CoiOpticalCurrentEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "An entry containing current information on optical layer related attributes of interfaces with an ifType opticalChannel(195). Entries are created by the feature when a new interface is added to the ifTable." INDEX { ifIndex, coiOptCurrentLane, coiOptCurrentIntervalType } ::= { coiOpticalCurrentTable 1 } CoiOpticalCurrentEntry ::= SEQUENCE { coiOptCurrentLane Integer32, coiOptCurrentIntervalType CoiIntervalType, coiOptCurrentTXPowerMax CoiOpticalPower, coiOptCurrentRXPowerMax CoiOpticalPower, coiOptCurrentOSNRMax Integer32, coiOptCurrentChromaticDispersionMax Integer32, coiOptCurrentDifferentialGroupDelayMax Integer32, coiOptCurrentSecondOrderPMDMax Integer32, coiOptCurrentPolarizationDependentLossMax Integer32, coiOptCurrentPolarizationChangeRateMax Integer32, coiOptCurrentPhaseNoiseMax Integer32, coiOptCurrentLBCMax Integer32, coiOptCurrentTXPowerMin CoiOpticalPower, coiOptCurrentRXPowerMin CoiOpticalPower, coiOptCurrentOSNRMin Integer32, coiOptCurrentChromaticDispersionMin Integer32, coiOptCurrentDifferentialGroupDelayMin Integer32, coiOptCurrentSecondOrderPMDMin Integer32, coiOptCurrentPolarizationDependentLossMin Integer32, coiOptCurrentPolarizationChangeRateMin Integer32, coiOptCurrentPhaseNoiseMin Integer32, coiOptCurrentLBCMin Integer32, coiOptCurrentTXPowerAvg CoiOpticalPower, coiOptCurrentRXPowerAvg CoiOpticalPower, coiOptCurrentOSNRAvg Integer32, coiOptCurrentChromaticDispersionAvg Integer32, coiOptCurrentDifferentialGroupDelayAvg Integer32, coiOptCurrentSecondOrderPMDAvg Integer32, coiOptCurrentPolarizationDependentLossAvg Integer32, coiOptCurrentPolarizationChangeRateAvg Integer32, coiOptCurrentPhaseNoiseAvg Integer32, coiOptCurrentLBCAvg Integer32, coiOptCurrentTimestamp OCTET STRING } coiOptCurrentLane OBJECT-TYPE SYNTAX Integer32 (1..12) MAX-ACCESS not-accessible STATUS current DESCRIPTION "This object specifies the lane number for the optical interface. Each optical controller is divided into data lanes with each lane operating at some data rate, giving an aggregated bandwidth of the controller as a whole. Lane is applicable for breakout mode of operation." ::= { coiOpticalCurrentEntry 1 } coiOptCurrentIntervalType OBJECT-TYPE SYNTAX CoiIntervalType MAX-ACCESS not-accessible STATUS current DESCRIPTION "This object gives the interval type during which the current performance statistics are accumulated." ::= { coiOpticalCurrentEntry 2 } coiOptCurrentTXPowerMax OBJECT-TYPE SYNTAX CoiOpticalPower UNITS "1/100 dBm" MAX-ACCESS read-only STATUS current DESCRIPTION "This object specifies the current max Transmit power for the interface in 1/100 dBm." ::= { coiOpticalCurrentEntry 3 } coiOptCurrentRXPowerMax OBJECT-TYPE SYNTAX CoiOpticalPower UNITS "1/100 dBm" MAX-ACCESS read-only STATUS current DESCRIPTION "This object specifies the current max Receive power for the interface in 1/100 dBm." ::= { coiOpticalCurrentEntry 4 } coiOptCurrentOSNRMax OBJECT-TYPE SYNTAX Integer32 UNITS "1/100 dB" MAX-ACCESS read-only STATUS current DESCRIPTION "This object specifies the current max Optical Signal to Noise Ratio for the interface in 1/100 dB." ::= { coiOpticalCurrentEntry 5 } coiOptCurrentChromaticDispersionMax OBJECT-TYPE SYNTAX Integer32 UNITS "ps/nm" MAX-ACCESS read-only STATUS current DESCRIPTION "This object specifies the current max measure of spread of light pulse for the interface in ps/nm." ::= { coiOpticalCurrentEntry 6 } coiOptCurrentDifferentialGroupDelayMax OBJECT-TYPE SYNTAX Integer32 UNITS "1/100 ps" MAX-ACCESS read-only STATUS current DESCRIPTION "This object specifies the current max propagation time difference between eigenmodes X and Y for the interface in 1/100 ps." ::= { coiOpticalCurrentEntry 7 } coiOptCurrentSecondOrderPMDMax OBJECT-TYPE SYNTAX Integer32 UNITS "1/100 ps^2" MAX-ACCESS read-only STATUS current DESCRIPTION "This object specifies the current max Second Order Polarization Mode Dispersion for the interface in 1/100 ps^2." ::= { coiOpticalCurrentEntry 8 } coiOptCurrentPolarizationDependentLossMax OBJECT-TYPE SYNTAX Integer32 UNITS "1/100 dB" MAX-ACCESS read-only STATUS current DESCRIPTION "This object specifies the current max Polarization Dependent Loss for the interface in 1/100 dB." ::= { coiOpticalCurrentEntry 9 } coiOptCurrentPolarizationChangeRateMax OBJECT-TYPE SYNTAX Integer32 UNITS "1/100 rad/s" MAX-ACCESS read-only STATUS current DESCRIPTION "This object specifies the current max Polarization Change Rate for the interface in 1/100 rad/s." ::= { coiOpticalCurrentEntry 10 } coiOptCurrentPhaseNoiseMax OBJECT-TYPE SYNTAX Integer32 UNITS "1/1000 dB" MAX-ACCESS read-only STATUS current DESCRIPTION "This object specifies the current max Fluctuations in the Phase of a Waveform for the interface in 1/1000 dB." ::= { coiOpticalCurrentEntry 11 } coiOptCurrentLBCMax OBJECT-TYPE SYNTAX Integer32 (0..1000) UNITS "1/10 %" MAX-ACCESS read-only STATUS current DESCRIPTION "This object specifies the current max Laser Bias Current in 1/10% for the interface." ::= { coiOpticalCurrentEntry 12 } coiOptCurrentTXPowerMin OBJECT-TYPE SYNTAX CoiOpticalPower UNITS "1/100 dBm" MAX-ACCESS read-only STATUS current DESCRIPTION "This object specifies the current min Transmit power for the interface in 1/100 dBm." ::= { coiOpticalCurrentEntry 13 } coiOptCurrentRXPowerMin OBJECT-TYPE SYNTAX CoiOpticalPower UNITS "1/100 dBm" MAX-ACCESS read-only STATUS current DESCRIPTION "This object specifies the current min Receive power for the interface in 1/100 dBm." ::= { coiOpticalCurrentEntry 14 } coiOptCurrentOSNRMin OBJECT-TYPE SYNTAX Integer32 UNITS "1/100 dB" MAX-ACCESS read-only STATUS current DESCRIPTION "This object specifies the current min Optical Signal to Noise Ratio for the interface in 1/100 dB." ::= { coiOpticalCurrentEntry 15 } coiOptCurrentChromaticDispersionMin OBJECT-TYPE SYNTAX Integer32 UNITS "ps/nm" MAX-ACCESS read-only STATUS current DESCRIPTION "This object specifies the current min measure of spread of light pulse for the interface in ps/nm." ::= { coiOpticalCurrentEntry 16 } coiOptCurrentDifferentialGroupDelayMin OBJECT-TYPE SYNTAX Integer32 UNITS "1/100 ps" MAX-ACCESS read-only STATUS current DESCRIPTION "This object specifies the current min propagation time difference between eigenmodes X and Y for the interface in 1/100 ps." ::= { coiOpticalCurrentEntry 17 } coiOptCurrentSecondOrderPMDMin OBJECT-TYPE SYNTAX Integer32 UNITS "1/100 ps^2" MAX-ACCESS read-only STATUS current DESCRIPTION "This object specifies the current min Second Order Polarization Mode Dispersion for the interface in 1/100 ps^2." ::= { coiOpticalCurrentEntry 18 } coiOptCurrentPolarizationDependentLossMin OBJECT-TYPE SYNTAX Integer32 UNITS "1/100 dB" MAX-ACCESS read-only STATUS current DESCRIPTION "This object specifies the current min Polarization Dependent Loss for the interface in 1/100 dB." ::= { coiOpticalCurrentEntry 19 } coiOptCurrentPolarizationChangeRateMin OBJECT-TYPE SYNTAX Integer32 UNITS "1/100 rad/s" MAX-ACCESS read-only STATUS current DESCRIPTION "This object specifies the current min Polarization Change Rate for the interface in 1/100 rad/s." ::= { coiOpticalCurrentEntry 20 } coiOptCurrentPhaseNoiseMin OBJECT-TYPE SYNTAX Integer32 UNITS "1/1000 dB" MAX-ACCESS read-only STATUS current DESCRIPTION "This object specifies the current min Fluctuations in the Phase of a Waveform in 1/1000 dB for the interface." ::= { coiOpticalCurrentEntry 21 } coiOptCurrentLBCMin OBJECT-TYPE SYNTAX Integer32 (0..1000) UNITS "1/10 %" MAX-ACCESS read-only STATUS current DESCRIPTION "This object specifies the current min Laser Bias Current in 1/10% for the interface." ::= { coiOpticalCurrentEntry 22 } coiOptCurrentTXPowerAvg OBJECT-TYPE SYNTAX CoiOpticalPower UNITS "1/100 dBm" MAX-ACCESS read-only STATUS current DESCRIPTION "This object specifies the current average Transmit power for the interface in 1/100 dBm." ::= { coiOpticalCurrentEntry 23 } coiOptCurrentRXPowerAvg OBJECT-TYPE SYNTAX CoiOpticalPower UNITS "1/100 dBm" MAX-ACCESS read-only STATUS current DESCRIPTION "This object specifies the current average Receive power for the interface in 1/100 dBm." ::= { coiOpticalCurrentEntry 24 } coiOptCurrentOSNRAvg OBJECT-TYPE SYNTAX Integer32 UNITS "1/100 dB" MAX-ACCESS read-only STATUS current DESCRIPTION "This object specifies the current average Optical Signal to Noise Ratio for the interface in 1/100 dB." ::= { coiOpticalCurrentEntry 25 } coiOptCurrentChromaticDispersionAvg OBJECT-TYPE SYNTAX Integer32 UNITS "ps/nm" MAX-ACCESS read-only STATUS current DESCRIPTION "This object specifies the current average measure of spread of light pulse for the interface in ps/nm." ::= { coiOpticalCurrentEntry 26 } coiOptCurrentDifferentialGroupDelayAvg OBJECT-TYPE SYNTAX Integer32 UNITS "1/100 ps" MAX-ACCESS read-only STATUS current DESCRIPTION "This object specifies the current average propagation time difference between eigenmodes X and Y for the interface in 1/100 ps." ::= { coiOpticalCurrentEntry 27 } coiOptCurrentSecondOrderPMDAvg OBJECT-TYPE SYNTAX Integer32 UNITS "1/100 ps^2" MAX-ACCESS read-only STATUS current DESCRIPTION "This object specifies the current average Second Order Polarization Mode Dispersion for the interface in 1/100 ps^2." ::= { coiOpticalCurrentEntry 28 } coiOptCurrentPolarizationDependentLossAvg OBJECT-TYPE SYNTAX Integer32 UNITS "1/100 dB" MAX-ACCESS read-only STATUS current DESCRIPTION "This object specifies the current average Polarization Dependent Loss for the interface in 1/100 dB." ::= { coiOpticalCurrentEntry 29 } coiOptCurrentPolarizationChangeRateAvg OBJECT-TYPE SYNTAX Integer32 UNITS "1/100 rad/s" MAX-ACCESS read-only STATUS current DESCRIPTION "This object specifies the current average Polarization Change Rate for the interface in 1/100 rad/s." ::= { coiOpticalCurrentEntry 30 } coiOptCurrentPhaseNoiseAvg OBJECT-TYPE SYNTAX Integer32 UNITS "1/1000 dB" MAX-ACCESS read-only STATUS current DESCRIPTION "This object specifies the current average Fluctuations in the Phase of a Waveform in 1/1000 dB for the interface." ::= { coiOpticalCurrentEntry 31 } coiOptCurrentLBCAvg OBJECT-TYPE SYNTAX Integer32 (0..1000) UNITS "1/10 %" MAX-ACCESS read-only STATUS current DESCRIPTION "This object specifies the current average Laser Bias Current in 1/10% for the interface." ::= { coiOpticalCurrentEntry 32 } coiOptCurrentTimestamp OBJECT-TYPE SYNTAX OCTET STRING MAX-ACCESS read-only STATUS current DESCRIPTION "This object specifies the timestamp for the current bucket for the interface." ::= { coiOpticalCurrentEntry 33 } coiOpticalIntervalTable OBJECT-TYPE SYNTAX SEQUENCE OF CoiOpticalIntervalEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "This table provides interval information for optical layer related attributes of interfaces with an ifType of opticalChannel(195), lane as coiOptIntervalLane, Interval as coiOptIntervalIntervalType and history bucket as coiOptIntervalIntervalType." ::= { coiOpticalPerformanceMonitoring 3 } coiOpticalIntervalEntry OBJECT-TYPE SYNTAX CoiOpticalIntervalEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "An entry containing interval information on optical layer related attributes of interfaces with an ifType opticalChannel(195). Entries are created by the feature when a new interface is added to the ifTable." INDEX { ifIndex, coiOptIntervalLane, coiOptIntervalIntervalType, coiOptIntervalNum } ::= { coiOpticalIntervalTable 1 } CoiOpticalIntervalEntry ::= SEQUENCE { coiOptIntervalLane Integer32, coiOptIntervalIntervalType CoiIntervalType, coiOptIntervalNum Integer32, coiOptIntervalTXPowerMax CoiOpticalPower, coiOptIntervalRXPowerMax CoiOpticalPower, coiOptIntervalOSNRMax Integer32, coiOptIntervalChromaticDispersionMax Integer32, coiOptIntervalDifferentialGroupDelayMax Integer32, coiOptIntervalSecondOrderPMDMax Integer32, coiOptIntervalPolarizationDependentLossMax Integer32, coiOptIntervalPolarizationChangeRateMax Integer32, coiOptIntervalPhaseNoiseMax Integer32, coiOptIntervalLBCMax Integer32, coiOptIntervalTXPowerMin CoiOpticalPower, coiOptIntervalRXPowerMin CoiOpticalPower, coiOptIntervalOSNRMin Integer32, coiOptIntervalChromaticDispersionMin Integer32, coiOptIntervalDifferentialGroupDelayMin Integer32, coiOptIntervalSecondOrderPMDMin Integer32, coiOptIntervalPolarizationDependentLossMin Integer32, coiOptIntervalPolarizationChangeRateMin Integer32, coiOptIntervalPhaseNoiseMin Integer32, coiOptIntervalLBCMin Integer32, coiOptIntervalTXPowerAvg CoiOpticalPower, coiOptIntervalRXPowerAvg CoiOpticalPower, coiOptIntervalOSNRAvg Integer32, coiOptIntervalChromaticDispersionAvg Integer32, coiOptIntervalDifferentialGroupDelayAvg Integer32, coiOptIntervalSecondOrderPMDAvg Integer32, coiOptIntervalPolarizationDependentLossAvg Integer32, coiOptIntervalPolarizationChangeRateAvg Integer32, coiOptIntervalPhaseNoiseAvg Integer32, coiOptIntervalLBCAvg Integer32, coiOptIntervalTimestamp OCTET STRING } coiOptIntervalLane OBJECT-TYPE SYNTAX Integer32 (1..12) MAX-ACCESS not-accessible STATUS current DESCRIPTION "This object specifies the lane number for the optical interface. Each optical controller is divided into data lanes with each lane operating at some data rate, giving an aggregated bandwidth of the controller as a whole.Lane is applicable for breakout mode of operation." ::= { coiOpticalIntervalEntry 1 } coiOptIntervalIntervalType OBJECT-TYPE SYNTAX CoiIntervalType MAX-ACCESS not-accessible STATUS current DESCRIPTION "This object gives the interval type during which the performance statistics are accumulated." ::= { coiOpticalIntervalEntry 2 } coiOptIntervalNum OBJECT-TYPE SYNTAX Integer32 (1..32) MAX-ACCESS not-accessible STATUS current DESCRIPTION "This object identifies the interval for which the set of interval performance values is available. The interval identified by 1 is the most recent 15 minute or 24 hour interval, and the interval identified by N is the interval immediately preceding the one identified by N-1." ::= { coiOpticalIntervalEntry 3 } coiOptIntervalTXPowerMax OBJECT-TYPE SYNTAX CoiOpticalPower UNITS "1/100 dBm" MAX-ACCESS read-only STATUS current DESCRIPTION "This object specifies the interval maximum Transmit power in 1/100 dBm for the interface." ::= { coiOpticalIntervalEntry 4 } coiOptIntervalRXPowerMax OBJECT-TYPE SYNTAX CoiOpticalPower UNITS "1/100 dBm" MAX-ACCESS read-only STATUS current DESCRIPTION "This object specifies the interval maximum Receive power in 1/100 dBm for the interface." ::= { coiOpticalIntervalEntry 5 } coiOptIntervalOSNRMax OBJECT-TYPE SYNTAX Integer32 UNITS "1/100 dB" MAX-ACCESS read-only STATUS current DESCRIPTION "This object specifies the interval maximum Optical Signal to Noise Ratio in 1/100 dB for the interface." ::= { coiOpticalIntervalEntry 6 } coiOptIntervalChromaticDispersionMax OBJECT-TYPE SYNTAX Integer32 UNITS "ps/nm" MAX-ACCESS read-only STATUS current DESCRIPTION "This object specifies the interval maximum measure of spread of light pulse for the interface in ps/nm." ::= { coiOpticalIntervalEntry 7 } coiOptIntervalDifferentialGroupDelayMax OBJECT-TYPE SYNTAX Integer32 UNITS "1/100 ps" MAX-ACCESS read-only STATUS current DESCRIPTION "This object specifies the interval maximum propagation time difference between eigenmodes X and Y for the interface in 1/100 ps." ::= { coiOpticalIntervalEntry 8 } coiOptIntervalSecondOrderPMDMax OBJECT-TYPE SYNTAX Integer32 UNITS "1/100 ps^2" MAX-ACCESS read-only STATUS current DESCRIPTION "This object specifies the interval maximum Second Order Polarization Mode Dispersion in 1/100 ps^2 for the interface." ::= { coiOpticalIntervalEntry 9 } coiOptIntervalPolarizationDependentLossMax OBJECT-TYPE SYNTAX Integer32 UNITS "1/100 dB" MAX-ACCESS read-only STATUS current DESCRIPTION "This object specifies the interval maximum Polarization Dependent Loss in 1/100 dB for the interface." ::= { coiOpticalIntervalEntry 10 } coiOptIntervalPolarizationChangeRateMax OBJECT-TYPE SYNTAX Integer32 UNITS "1/100 rad/s" MAX-ACCESS read-only STATUS current DESCRIPTION "This object specifies the interval maximum Polarization Change Rate in 1/100 rad/s for the interface." ::= { coiOpticalIntervalEntry 11 } coiOptIntervalPhaseNoiseMax OBJECT-TYPE SYNTAX Integer32 UNITS "1/1000 dB" MAX-ACCESS read-only STATUS current DESCRIPTION "This object specifies the interval maximum Fluctuations in the Phase of a Waveform in 1/1000 dB for the interface." ::= { coiOpticalIntervalEntry 12 } coiOptIntervalLBCMax OBJECT-TYPE SYNTAX Integer32 UNITS "1/10 %" MAX-ACCESS read-only STATUS current DESCRIPTION "This object specifies the interval maximum Laser Bias Current in 1/10% for the interface." ::= { coiOpticalIntervalEntry 13 } coiOptIntervalTXPowerMin OBJECT-TYPE SYNTAX CoiOpticalPower UNITS "1/100 dBm" MAX-ACCESS read-only STATUS current DESCRIPTION "This object specifies the interval minimum Transmit power in 1/100 dBm for the interface." ::= { coiOpticalIntervalEntry 14 } coiOptIntervalRXPowerMin OBJECT-TYPE SYNTAX CoiOpticalPower UNITS "1/100 dBm" MAX-ACCESS read-only STATUS current DESCRIPTION "This object specifies the interval minimum Receive power in 1/100 dBm for the interface." ::= { coiOpticalIntervalEntry 15 } coiOptIntervalOSNRMin OBJECT-TYPE SYNTAX Integer32 UNITS "1/100 dB" MAX-ACCESS read-only STATUS current DESCRIPTION "This object specifies the interval minimum Optical Signal to Noise Ratio in 1/100 dB for the interface." ::= { coiOpticalIntervalEntry 16 } coiOptIntervalChromaticDispersionMin OBJECT-TYPE SYNTAX Integer32 UNITS "ps/nm" MAX-ACCESS read-only STATUS current DESCRIPTION "This object specifies the interval minimum measure of spread of light pulse in ps/nm for the interface." ::= { coiOpticalIntervalEntry 17 } coiOptIntervalDifferentialGroupDelayMin OBJECT-TYPE SYNTAX Integer32 UNITS "1/100 ps" MAX-ACCESS read-only STATUS current DESCRIPTION "This object specifies the interval minimum propagation time difference between eigenmodes X and Y in 1/100 ps for the interface." ::= { coiOpticalIntervalEntry 18 } coiOptIntervalSecondOrderPMDMin OBJECT-TYPE SYNTAX Integer32 UNITS "1/100 ps^2" MAX-ACCESS read-only STATUS current DESCRIPTION "This object specifies the interval minimum Second Order Polarization Mode Dispersion in 1/100 ps^2 for the interface." ::= { coiOpticalIntervalEntry 19 } coiOptIntervalPolarizationDependentLossMin OBJECT-TYPE SYNTAX Integer32 UNITS "1/100 dB" MAX-ACCESS read-only STATUS current DESCRIPTION "This object specifies the interval minimum Polarization Dependent Loss in 1/100 dB for the interface." ::= { coiOpticalIntervalEntry 20 } coiOptIntervalPolarizationChangeRateMin OBJECT-TYPE SYNTAX Integer32 UNITS "1/100 rad/s" MAX-ACCESS read-only STATUS current DESCRIPTION "This object specifies the interval minimum Polarization Change Rate in 1/100 rad/s for the interface." ::= { coiOpticalIntervalEntry 21 } coiOptIntervalPhaseNoiseMin OBJECT-TYPE SYNTAX Integer32 UNITS "1/1000 dB" MAX-ACCESS read-only STATUS current DESCRIPTION "This object specifies the interval minimum Fluctuations in the Phase of a Waveform in 1/1000 dB for the interface." ::= { coiOpticalIntervalEntry 22 } coiOptIntervalLBCMin OBJECT-TYPE SYNTAX Integer32 UNITS "1/10 %" MAX-ACCESS read-only STATUS current DESCRIPTION "This object specifies the interval minimum Laser Bias Current in 1/10% for the interface." ::= { coiOpticalIntervalEntry 23 } coiOptIntervalTXPowerAvg OBJECT-TYPE SYNTAX CoiOpticalPower UNITS "1/100 dBm" MAX-ACCESS read-only STATUS current DESCRIPTION "This object specifies the interval average Transmit power in 1/100 dBm for the interface." ::= { coiOpticalIntervalEntry 24 } coiOptIntervalRXPowerAvg OBJECT-TYPE SYNTAX CoiOpticalPower UNITS "1/100 dBm" MAX-ACCESS read-only STATUS current DESCRIPTION "This object specifies the interval average Receive power in 1/100 dBm for the interface." ::= { coiOpticalIntervalEntry 25 } coiOptIntervalOSNRAvg OBJECT-TYPE SYNTAX Integer32 UNITS "1/100 dB" MAX-ACCESS read-only STATUS current DESCRIPTION "This object specifies the interval average Optical Signal to Noise Ratio in 1/100 dB for the interface." ::= { coiOpticalIntervalEntry 26 } coiOptIntervalChromaticDispersionAvg OBJECT-TYPE SYNTAX Integer32 UNITS "ps/nm" MAX-ACCESS read-only STATUS current DESCRIPTION "This object specifies the interval average measure of spread of light pulse in ps/nm for the interface." ::= { coiOpticalIntervalEntry 27 } coiOptIntervalDifferentialGroupDelayAvg OBJECT-TYPE SYNTAX Integer32 UNITS "1/100 ps" MAX-ACCESS read-only STATUS current DESCRIPTION "This object specifies the interval average propagation time difference between eigenmodes X and Y in 1/100 ps for the interface." ::= { coiOpticalIntervalEntry 28 } coiOptIntervalSecondOrderPMDAvg OBJECT-TYPE SYNTAX Integer32 UNITS "1/100 ps^2" MAX-ACCESS read-only STATUS current DESCRIPTION "This object specifies the interval average Second Order Polarization Mode Dispersion in 1/100 ps^2 for the interface." ::= { coiOpticalIntervalEntry 29 } coiOptIntervalPolarizationDependentLossAvg OBJECT-TYPE SYNTAX Integer32 UNITS "1/100 dB" MAX-ACCESS read-only STATUS current DESCRIPTION "This object specifies the interval average Polarization Dependent Loss in 1/100 dB for the interface." ::= { coiOpticalIntervalEntry 30 } coiOptIntervalPolarizationChangeRateAvg OBJECT-TYPE SYNTAX Integer32 UNITS "1/100 rad/s" MAX-ACCESS read-only STATUS current DESCRIPTION "This object specifies the interval average Polarization Change Rate in 1/100 rad/s for the interface." ::= { coiOpticalIntervalEntry 31 } coiOptIntervalPhaseNoiseAvg OBJECT-TYPE SYNTAX Integer32 UNITS "1/1000 dB" MAX-ACCESS read-only STATUS current DESCRIPTION "This object specifies the interval average Fluctuations in the Phase of a Waveform in 1/1000 dB for the interface." ::= { coiOpticalIntervalEntry 32 } coiOptIntervalLBCAvg OBJECT-TYPE SYNTAX Integer32 UNITS "1/10 %" MAX-ACCESS read-only STATUS current DESCRIPTION "This object specifies the interval average Laser Bias Current in 1/10 % for the interface." ::= { coiOpticalIntervalEntry 33 } coiOptIntervalTimestamp OBJECT-TYPE SYNTAX OCTET STRING MAX-ACCESS read-only STATUS current DESCRIPTION "This object specifies the timestamp, for the bucket specified by 'coiOptIntervalNum', for the interface." ::= { coiOpticalIntervalEntry 34 } coiOpticalEquipmentAlarmGroup OBJECT IDENTIFIER ::= { ciscoOpticalMIBObjects 4 } coiOpticalAlarmLocation OBJECT-TYPE SYNTAX DisplayString MAX-ACCESS accessible-for-notify STATUS current DESCRIPTION "This object indicates the location of the component that raised alarm, within the device." ::= { coiOpticalEquipmentAlarmGroup 1 } coiOpticalAlarmType OBJECT-TYPE SYNTAX CoiOptAlarmType MAX-ACCESS accessible-for-notify STATUS current DESCRIPTION "This object indicates the type of alarm that is raised." ::= { coiOpticalEquipmentAlarmGroup 2 } coiOpticalAlarmTimeStamp OBJECT-TYPE SYNTAX TimeStamp MAX-ACCESS accessible-for-notify STATUS current DESCRIPTION "This object gives the time when an event occurred. This is accurate only upto a second." ::= { coiOpticalEquipmentAlarmGroup 3 } coiOpticalAlarmName OBJECT-TYPE SYNTAX DisplayString MAX-ACCESS accessible-for-notify STATUS current DESCRIPTION "This variable gives the user-visible name, which uniquely identifies the alarm in the system." ::= { coiOpticalEquipmentAlarmGroup 4 } coiOpticalAlarmAdditionalInfo OBJECT-TYPE SYNTAX DisplayString MAX-ACCESS accessible-for-notify STATUS current DESCRIPTION "This variable provides additional info about the alarm. This object would be a null string if no additional information is specified." ::= { coiOpticalEquipmentAlarmGroup 5 } coiOpticalAlarmSeverity OBJECT-TYPE SYNTAX CoiOptAlarmSeverity MAX-ACCESS accessible-for-notify STATUS current DESCRIPTION "This variable specifies alarm severity." ::= { coiOpticalEquipmentAlarmGroup 6 } coiOpticalAlarmStatus OBJECT-TYPE SYNTAX CoiOptAlarmStatus MAX-ACCESS accessible-for-notify STATUS current DESCRIPTION "This variable specifies alarm status." ::= { coiOpticalEquipmentAlarmGroup 7 } coiOpticalAlarmServiceAffecting OBJECT-TYPE SYNTAX CoiOptAlarmServiceAffecting MAX-ACCESS accessible-for-notify STATUS current DESCRIPTION "This variable specifies the service affecting state of the alarm." ::= { coiOpticalEquipmentAlarmGroup 8 } -- MIB Conformance Statements ciscoOpticalMIBConformance OBJECT IDENTIFIER ::= { ciscoOpticalMIB 2 } ciscoOpticalMIBCompliances OBJECT IDENTIFIER ::= { ciscoOpticalMIBConformance 1 } ciscoOpticalMIBGroups OBJECT IDENTIFIER ::= { ciscoOpticalMIBConformance 2 } ciscoOpticalMIBCompliance MODULE-COMPLIANCE STATUS deprecated -- superceded by -- ciscoOpticalMIBComplianceRev1 DESCRIPTION "The compliance statement for platforms that monitor the parameters for the optical interfaces." MODULE -- this module MANDATORY-GROUPS { coiOpticalGroup } GROUP coiOpticalControllerGroup DESCRIPTION "The collection of objects to allow configurations and give information related to the optical layer characteristics for interfaces of ifType opticalChannel(195)." GROUP coiOpticalControllerPerLaneGroup DESCRIPTION "The collection of objects to give information related to the optical layer characteristics for interfaces of ifType opticalChannel(195) and lane number as coiOpticalControllerLane." GROUP coiOpticalClientInfoGroup DESCRIPTION "The collection of objects to give information related to optical's client layer related attributes of interfaces with an ifType of ethernetCsmacd(6)." GROUP coiOpticalThresholdGroup DESCRIPTION "The collection of objects used for monitoring the threshold information for optical layer related attributes of interfaces with an ifType of opticalChannel(195)." GROUP coiOpticalCurrentGroup DESCRIPTION "The collection of objects used for monitoring the current information for optical layer related attributes of interfaces with an ifType of opticalChannel(195) in a current interval." GROUP coiOpticalIntervalGroup DESCRIPTION "The collection of objects used for monitoring the interval information for optical layer related attributes of interfaces with an ifType of opticalChannel(195) in a given interval." GROUP coiOpticalNotifEnableGroup DESCRIPTION "The collection of objects to enable the notification generations upon an interface's defect status change on optics layer." GROUP coiOpticalNotifStatusObjectGroup DESCRIPTION "The object to be included in an Optical interface's defect status change notification." GROUP coiOpticalNotifGroup DESCRIPTION "The optical status change notifications whenever the defect status of optical layer on an interface changes." GROUP coiOpticalEquipmentAlarmInfoGroup DESCRIPTION "The optical equipment alarm notifications whenever the equipment failed alarm is detected." ::= { ciscoOpticalMIBCompliances 1 } ciscoOpticalMIBComplianceRev1 MODULE-COMPLIANCE STATUS current DESCRIPTION "The compliance statement for platforms that monitor the parameters for the optical interfaces." MODULE -- this module MANDATORY-GROUPS { coiOpticalGroup } GROUP coiOpticalControllerGroup DESCRIPTION "The collection of objects to allow configurations and give information related to the optical layer characteristics for interfaces of ifType opticalChannel(195)." GROUP coiOpticalControllerPerLaneGroup DESCRIPTION "The collection of objects to give information related to the optical layer characteristics for interfaces of ifType opticalChannel(195) and lane number as coiOpticalControllerLane." GROUP coiOpticalClientInfoGroup DESCRIPTION "The collection of objects to give information related to optical's client layer related attributes of interfaces with an ifType of ethernetCsmacd(6)." GROUP coiOpticalThresholdGroup DESCRIPTION "The collection of objects used for monitoring the threshold information for optical layer related attributes of interfaces with an ifType of opticalChannel(195)." GROUP coiOpticalCurrentGroup DESCRIPTION "The collection of objects used for monitoring the current information for optical layer related attributes of interfaces with an ifType of opticalChannel(195) in a current interval." GROUP coiOpticalIntervalGroup DESCRIPTION "The collection of objects used for monitoring the interval information for optical layer related attributes of interfaces with an ifType of opticalChannel(195) in a given interval." GROUP coiOpticalNotifEnableGroup DESCRIPTION "The collection of objects to enable the notification generations upon an interface's defect status change on optics layer." GROUP coiOpticalNotifStatusObjectGroup DESCRIPTION "The object to be included in an Optical interface's defect status change notification." GROUP coiOpticalNotifGroup DESCRIPTION "The optical status change notifications whenever the defect status of optical layer on an interface changes." GROUP coiOpticalEquipmentAlarmInfoGroup DESCRIPTION "The optical equipment alarm notifications whenever the equipment failed alarm is detected." GROUP coiOpticalPowerGroup DESCRIPTION "The collection of objects used for monitoring the total power information for optical layer related attributes of interfaces with an ifType of opticalChannel(195)." ::= { ciscoOpticalMIBCompliances 2 } -- units of conformance coiOpticalGroup OBJECT-GROUP OBJECTS { coiOpticalControllerLaserStatus, coiOpticalControllerTransmitPower, coiOpticalControllerOpticsType, coiOpticalControllerRXLowThreshold, coiOpticalControllerTXLowThreshold, coiOpticalControllerRXHighThreshold, coiOpticalControllerTXHighThreshold, coiOpticalControllerLBCHighThreshold, coiOpticalControllerPerLaneRXPower, coiOpticalControllerPerLaneTXPower, coiOpticalControllerPerLaneLBC, coiOpticalControllerStatus, coiOptThreshTXPowerMin, coiOptThreshRXPowerMin, coiOptThreshLBCMin, coiOptThreshTXPowerMax, coiOptThreshRXPowerMax, coiOptThreshLBCMax, coiOptCurrentTXPowerMax, coiOptCurrentRXPowerMax, coiOptCurrentLBCMax, coiOptCurrentTXPowerMin, coiOptCurrentRXPowerMin, coiOptCurrentLBCMin, coiOptCurrentTXPowerAvg, coiOptCurrentRXPowerAvg, coiOptCurrentLBCAvg, coiOptIntervalTXPowerMax, coiOptIntervalRXPowerMax, coiOptIntervalLBCMax, coiOptIntervalTXPowerMin, coiOptIntervalRXPowerMin, coiOptIntervalLBCMin, coiOptIntervalTXPowerAvg, coiOptIntervalRXPowerAvg, coiOptIntervalLBCAvg } STATUS current DESCRIPTION "The collection of objects to give information related to the optical layer characteristics for interfaces of ifType opticalChannel(195)." ::= { ciscoOpticalMIBGroups 1 } coiOpticalControllerGroup OBJECT-GROUP OBJECTS { coiOpticalControllerWavelength, coiOpticalControllerLaserStatus, coiOpticalControllerFrequency, coiOpticalControllerChannelNumber, coiOpticalControllerTransmitPower, coiOpticalControllerOpticsType, coiOpticalControllerRXLowThreshold, coiOpticalControllerTXLowThreshold, coiOpticalControllerRXHighThreshold, coiOpticalControllerTXHighThreshold, coiOpticalControllerLBCHighThreshold, coiOpticalControllerStatus, coiOpticalControllerPortType } STATUS current DESCRIPTION "The collection of objects to allow configurations and give information related to the optical layer characteristics for interfaces of ifType opticalChannel(195)." ::= { ciscoOpticalMIBGroups 2 } coiOpticalControllerPerLaneGroup OBJECT-GROUP OBJECTS { coiOpticalControllerPerLaneRXPower, coiOpticalControllerPerLaneTXPower, coiOpticalControllerPerLaneLBC, coiOpticalControllerPerLaneOSNR, coiOpticalControllerPerLaneChromaticDispersion, coiOpticalControllerPerLaneDifferentialGroupDelay, coiOpticalControllerPerLaneSecondOrderPMD, coiOpticalControllerPerLanePolarizationDependentLoss, coiOpticalControllerPerLanePolarizationChangeRate, coiOpticalControllerPerLanePhaseNoise } STATUS current DESCRIPTION "The collection of objects to give information related to the optical layer characteristics for interfaces of ifType opticalChannel(195) and lane number as coiOpticalControllerLane." ::= { ciscoOpticalMIBGroups 3 } coiOpticalClientInfoGroup OBJECT-GROUP OBJECTS { coiOpticalClientEthernetNeighbourMAC } STATUS current DESCRIPTION "The collection of objects to give information related to optical's client layer related attributes of interfaces with an ifType of ethernetCsmacd(6)." ::= { ciscoOpticalMIBGroups 4 } coiOpticalThresholdGroup OBJECT-GROUP OBJECTS { coiOptThreshTXPowerMin, coiOptThreshRXPowerMin, coiOptThreshOSNRMin, coiOptThreshChromaticDispersionMin, coiOptThreshDifferentialGroupDelayMin, coiOptThreshSecondOrderPMDMin, coiOptThreshPolarizationDependentLossMin, coiOptThreshPolarizationChangeRateMin, coiOptThreshPhaseNoiseMin, coiOptThreshLBCMin, coiOptThreshTXPowerMax, coiOptThreshRXPowerMax, coiOptThreshOSNRMax, coiOptThreshChromaticDispersionMax, coiOptThreshDifferentialGroupDelayMax, coiOptThreshSecondOrderPMDMax, coiOptThreshPolarizationDependentLossMax, coiOptThreshPolarizationChangeRateMax, coiOptThreshPhaseNoiseMax, coiOptThreshLBCMax, coiOptThreshTXPowerEnableMin, coiOptThreshRXPowerEnableMin, coiOptThreshOSNREnableMin, coiOptThreshChromaticDispersionEnableMin, coiOptThreshDifferentialGroupDelayEnableMin, coiOptThreshSecondOrderPMDEnableMin, coiOptThreshPolarizationDependentLossEnableMin, coiOptThreshPolarizationChangeRateEnableMin, coiOptThreshPhaseNoiseEnableMin, coiOptThreshLBCEnableMin, coiOptThreshTXPowerEnableMax, coiOptThreshRXPowerEnableMax, coiOptThreshOSNREnableMax, coiOptThreshChromaticDispersionEnableMax, coiOptThreshDifferentialGroupDelayEnableMax, coiOptThreshSecondOrderPMDEnableMax, coiOptThreshPolarizationDependentLossEnableMax, coiOptThreshPolarizationChangeRateEnableMax, coiOptThreshPhaseNoiseEnableMax, coiOptThreshLBCEnableMax } STATUS current DESCRIPTION "The collection of objects used for monitoring the threshold information for optical layer related attributes of interfaces with an ifType of opticalChannel(195)." ::= { ciscoOpticalMIBGroups 5 } coiOpticalCurrentGroup OBJECT-GROUP OBJECTS { coiOptCurrentTXPowerMax, coiOptCurrentRXPowerMax, coiOptCurrentOSNRMax, coiOptCurrentChromaticDispersionMax, coiOptCurrentDifferentialGroupDelayMax, coiOptCurrentSecondOrderPMDMax, coiOptCurrentPolarizationDependentLossMax, coiOptCurrentPolarizationChangeRateMax, coiOptCurrentPhaseNoiseMax, coiOptCurrentLBCMax, coiOptCurrentTXPowerMin, coiOptCurrentRXPowerMin, coiOptCurrentOSNRMin, coiOptCurrentChromaticDispersionMin, coiOptCurrentDifferentialGroupDelayMin, coiOptCurrentSecondOrderPMDMin, coiOptCurrentPolarizationDependentLossMin, coiOptCurrentPolarizationChangeRateMin, coiOptCurrentPhaseNoiseMin, coiOptCurrentLBCMin, coiOptCurrentTXPowerAvg, coiOptCurrentRXPowerAvg, coiOptCurrentOSNRAvg, coiOptCurrentChromaticDispersionAvg, coiOptCurrentDifferentialGroupDelayAvg, coiOptCurrentSecondOrderPMDAvg, coiOptCurrentPolarizationDependentLossAvg, coiOptCurrentPolarizationChangeRateAvg, coiOptCurrentPhaseNoiseAvg, coiOptCurrentLBCAvg, coiOptCurrentTimestamp } STATUS current DESCRIPTION "The collection of objects used for monitoring the current information for optical layer related attributes of interfaces with an ifType of opticalChannel(195) in a current interval." ::= { ciscoOpticalMIBGroups 6 } coiOpticalIntervalGroup OBJECT-GROUP OBJECTS { coiOptIntervalTXPowerMax, coiOptIntervalRXPowerMax, coiOptIntervalOSNRMax, coiOptIntervalChromaticDispersionMax, coiOptIntervalDifferentialGroupDelayMax, coiOptIntervalSecondOrderPMDMax, coiOptIntervalPolarizationDependentLossMax, coiOptIntervalPolarizationChangeRateMax, coiOptIntervalPhaseNoiseMax, coiOptIntervalLBCMax, coiOptIntervalTXPowerMin, coiOptIntervalRXPowerMin, coiOptIntervalOSNRMin, coiOptIntervalChromaticDispersionMin, coiOptIntervalDifferentialGroupDelayMin, coiOptIntervalSecondOrderPMDMin, coiOptIntervalPolarizationDependentLossMin, coiOptIntervalPolarizationChangeRateMin, coiOptIntervalPhaseNoiseMin, coiOptIntervalLBCMin, coiOptIntervalTXPowerAvg, coiOptIntervalRXPowerAvg, coiOptIntervalOSNRAvg, coiOptIntervalChromaticDispersionAvg, coiOptIntervalDifferentialGroupDelayAvg, coiOptIntervalSecondOrderPMDAvg, coiOptIntervalPolarizationDependentLossAvg, coiOptIntervalPolarizationChangeRateAvg, coiOptIntervalPhaseNoiseAvg, coiOptIntervalLBCAvg, coiOptIntervalTimestamp } STATUS current DESCRIPTION "The collection of objects used for monitoring the interval information for optical layer related attributes of interfaces with an ifType of opticalChannel(195) in a given interval." ::= { ciscoOpticalMIBGroups 7 } coiOpticalNotifEnableGroup OBJECT-GROUP OBJECTS { coiOpticalNotifEnabled } STATUS current DESCRIPTION "The collection of objects to enable the notification generations upon an interface's defect status change on optics layer." ::= { ciscoOpticalMIBGroups 8 } coiOpticalNotifStatusObjectGroup OBJECT-GROUP OBJECTS { coiOpticalControllerStatus } STATUS current DESCRIPTION "The object to be included in an Optical interface's defect status change notification." ::= { ciscoOpticalMIBGroups 9 } coiOpticalNotifGroup NOTIFICATION-GROUP NOTIFICATIONS { coiOpticsStatusChange, coiOpticalEquipmentAlarm } STATUS current DESCRIPTION "The optical status change notifications whenever the defect status of optical layer on an interface changes." ::= { ciscoOpticalMIBGroups 10 } coiOpticalEquipmentAlarmInfoGroup OBJECT-GROUP OBJECTS { coiOpticalAlarmLocation, coiOpticalAlarmType, coiOpticalAlarmTimeStamp, coiOpticalAlarmName, coiOpticalAlarmAdditionalInfo, coiOpticalAlarmSeverity, coiOpticalAlarmStatus, coiOpticalAlarmServiceAffecting } STATUS current DESCRIPTION "The optical equipment notifications whenever the alarm is generated." ::= { ciscoOpticalMIBGroups 11 } coiOpticalPowerGroup OBJECT-GROUP OBJECTS { coiOpticalControllerTotalRXPower, coiOpticalControllerTotalTXPower } STATUS current DESCRIPTION "The collection of objects used for monitoring the total power information for optical layer related attributes of interfaces with an ifType of opticalChannel(195)." ::= { ciscoOpticalMIBGroups 12 } END