-- ***************************************************************** -- CISCO-L4L7MODULE-RESOURCE-LIMIT-MIB: MIB for limiting resources -- -- August 2005, Subrahmanya Hegde -- -- Copyright (c) 2005-2013 by Cisco Systems Inc. -- All rights reserved. -- ***************************************************************** CISCO-L4L7MODULE-RESOURCE-LIMIT-MIB DEFINITIONS ::= BEGIN IMPORTS MODULE-IDENTITY, OBJECT-TYPE, Unsigned32, Gauge32, Counter32, Counter64, NOTIFICATION-TYPE FROM SNMPv2-SMI MODULE-COMPLIANCE, OBJECT-GROUP, NOTIFICATION-GROUP FROM SNMPv2-CONF TruthValue, TEXTUAL-CONVENTION, RowStatus, StorageType, TimeStamp FROM SNMPv2-TC entPhysicalIndex FROM ENTITY-MIB SnmpAdminString FROM SNMP-FRAMEWORK-MIB InetAddressType, InetAddress FROM INET-ADDRESS-MIB ciscoMgmt FROM CISCO-SMI; ciscoL4L7moduleResourceLimitMIB MODULE-IDENTITY LAST-UPDATED "201302200000Z" ORGANIZATION "Cisco Systems, Inc." CONTACT-INFO "Cisco Systems Customer Service Postal: 170 W Tasman Drive San Jose, CA 95134 USA Tel: +1 800 553-NETS E-mail: cs-l4l7security@cisco.com" DESCRIPTION "The MIB module for managing resource classes and configuring limits(max/min) to different resources. The resource referenced in this MIB are in addition to resource information availale in other MIBs. This MIB is applicable to L4-L7 modules which supports managing resource limits using a centralized approach. The resources (but not limited to) configured are of following categories: - TCP/IP Connections - MAC Addresses - syslog buffer, ACL Memmory - NAT Translations etc ciscoL4L7ResourceClassTable is used for adding/deleting resource classes. Resource class is identified by a name to which limits of multiple resources can be configured. ciscoL4L7ResourceLimitTable is used for adding/deleting limits to resources in a resource class. This limit is either maximum value and/or minimal value. ciscoL4L7ResourceRateLimitTable is used for adding/deleting rate limits to resources in a resource class. Terminologies used: ARP - Address Resolution Protocol. ACL - Access Control List. NAT - Network Address Translation. NBAR - Network Based Application Recognition. BPDU - Bridge Protocol Data Unit." REVISION "201302200000Z" DESCRIPTION "Added the following two enum names to CiscoResourceLimitType TC: - cpu - memory Added the following groups: - ciscoL4L7ResourceNotifGroupRev2 - ciscoL4L7ResourceNotifOnlyObjectsGroupExt Deprecated ciscoL4L7ResourceNotifGroupRev1; Updated the DESCRIOTION of the following objects: - clrResourceRateLimitReachedNotifEnabled - clrResourceLimitReachedNotifEnabled" REVISION "201209200000Z" DESCRIPTION "Added the following groups - ciscoL4L7ResourceNotifGroupRev1 - ciscoL4L7ResourceNotifOnlyObjectsGroup Deprecated the following groups - ciscoL4L7ResourceNotifGroup Added the following compliance - ciscoL4L7ResourceLimitComplianceRev6" REVISION "201106100000Z" DESCRIPTION "-Added following OBJECT-TYPEs in table ciscoL4L7BufferUtilizationTable. crlExternalBufferUsageValue crlExternalPercentageBufferUsage crlExternalPercentageBufferUsageDisplay -Deprecated OBJECT-GROUP ciscoL4L7BufferUtilizationGroup. -Added OBJECT-GROUP ciscoL4L7BufferUtilizationGroupRev1. -Deprecated MODULE-COMPLIANCE ciscoL4L7ResourceLimitComplianceRev4. -Added MODULE-COMPLIANCE ciscoL4L7ResourceLimitComplianceRev5." REVISION "201104150000Z" DESCRIPTION "- Added new table ciscoL4L7NpCpuUtilTable. - Added OBJECT-GROUP ciscoL4L7NpCpuUtilizationGroup. - Deprecated MODULE-COMPLIANCE ciscoL4L7ResourceLimitComplianceRev3. - Added MODULE-COMPLIANCE ciscoL4L7ResourceLimitComplianceRev4." REVISION "201012060000Z" DESCRIPTION "- Added TEXTUAL-CONVENTION CiscoBufferUtilPercentage. - Added table ciscoL4L7BufferUtilizationTable. - Added an OBJECT-GROUP ciscoL4L7BufferUtilizationGroup. - Deprecated MODULE-COMPLIANCE ciscoL4L7ResourceLimitComplianceRev2. - Added MODULE-COMPLIANCE ciscoL4L7ResourceLimitComplianceRev3." REVISION "200803070000Z" DESCRIPTION "- Added TEXTUAL-CONVENTION CiscoResourceType. - Added table ciscoL4L7ResourceUsageSummaryTable. - Added an OBJECT-GROUP ciscoL4L7ResourceUsageSummaryGroup. - Deprecated MODULE-COMPLIANCE ciscoL4L7ResourceLimitComplianceRev1. - Added MODULE-COMPLIANCE ciscoL4L7ResourceLimitComplianceRev2." REVISION "200802070000Z" DESCRIPTION "- Added following enumerations in CiscoRateLimitResourceType sslConnections (9) mgmtBandwidth (10) throughput (11) missedMac (12) httpCompression (13) - Updated the description of bandwidth(4) enumeration in CiscoRateLimitResourceType." REVISION "200606190000Z" DESCRIPTION "- Added following enumerations in CiscoResourceLimitType hosts (15) ipsecSessions (16) asdmSessions (17) sshSessions (18) telnetSessions (19) - Added following objects in ciscoL4L7ResourceLimitTable crlResourceLimitCurrentUsage crlResourceLimitPeakUsage crlResourceLimitReqsDeniedCount - Added following objects in ciscoL4L7RateLimitTable crlRateLimitResourceCurrentUsage crlRateLimitResourcePeakUsage crlRateLimitResourceReqsDeniedCount - Added following objects: clrResourceLimitReachedNotifEnabled clrResourceRateLimitReachedNotifEnabled - Added following Notification objects clrResourceLimitReached clrResourceRateLimitReached - Added following in Compliance/Conformance ciscoL4L7ResourceLimitComplianceRev1." REVISION "200508050000Z" DESCRIPTION "Initial version of the MIB module." ::= { ciscoMgmt 480 } ciscoL4L7ResourceLimitNotifs OBJECT IDENTIFIER ::= { ciscoL4L7moduleResourceLimitMIB 0 } ciscoL4L7ResourceLimitMIBObjects OBJECT IDENTIFIER ::= { ciscoL4L7moduleResourceLimitMIB 1 } ciscoResourceLimitMIBConform OBJECT IDENTIFIER ::= { ciscoL4L7moduleResourceLimitMIB 2 } crlResource OBJECT IDENTIFIER ::= { ciscoL4L7ResourceLimitMIBObjects 1 } crlNotificationObjects OBJECT IDENTIFIER ::= { ciscoL4L7ResourceLimitMIBObjects 2 } crlNotificationOnlyObjects OBJECT IDENTIFIER ::= { ciscoL4L7ResourceLimitMIBObjects 3 } CiscoResourceClass ::= TEXTUAL-CONVENTION STATUS current DESCRIPTION "This textual convention is used for representing resource classes. A resource class is identified by a name preferably in human readable form. This resource class is used for identifying different type of resources. The resource class can represent single resource type or multiple resource type. Resource category examples: memory, connections NAT(network address translation) translations, number of syslog messages etc." SYNTAX OCTET STRING (SIZE (0..64)) CiscoResourceLimitType ::= TEXTUAL-CONVENTION STATUS current DESCRIPTION "This object represents the resource type. The possible values are : all (1) : This is not a resource. However this value acts as the wild card value to set all the resources at the same time. If an entry exists with this value, then for all the resources that are not configured in this table will have the value specified in this entry. macAddresses(2) : The number of MAC addresses allowed in the MAC address table. concurrentConns (3) : Concurrent TCP/UDP connections that are supported. Connections exist between any two hosts. This is applicable for through the box connections only. mgmtConnections (4) : This is applicable for to-the-box traffic only. proxyConns (5) : Sticky connections limit traffic to the individual real servers by allowing multiple connections from the same client to stick (or attach) to the same real server using source IP addresses, source IP subnets, cookies, and the secure socket layer (SSL) or by redirecting these connections using Hypertext Transfer Protocol (HTTP) redirect messages. probes (6) : the number of health probes. stickyEntries (7) : the number of sticky entries. This refers to statically configured entries and dynamically created ones. It represents the pool of entries available for use/re-use. natTranslations (8) : the number of NAT Translations. regexState (9) : Regular expression state. Regex states are nodes in the regular expression state graph, used for matching and sticking on HTTP fields such as URL, header, cookies. aclMemory (10) : Memory that is allocated for managing ACLs. ipReassemBuffer (11) : buffer that is allocated for IP Reassembly. syslogBuffer (12) : buffer that is allocated for syslog messages that can be logged in the system. tcpOOOBuffer (13) : buffer that is allocated for TCP Out Of Order packets. sslConnections (14) : The number of SSL Connections. hosts (15) : Number of hosts allowed through the system. ipsecSessions (16) : Number of IPSec management sessions. asdmSessions (17) : Number of ASDM management sessions. sshSessions (18) : Number of SSH management sessions. telnetSessions (19) : Number of Telnet management sessions. cpu (20) : CPU utilization by the system. memory (21) : Memory utilization by the system." SYNTAX INTEGER { all(1), macAddresses(2), concurrentConns(3), mgmtConnections(4), proxyConns(5), probes(6), stickyEntries(7), natTranslations(8), regexState(9), aclMemory(10), syslogBuffer(11), ipReassemBuffer(12), tcpOOOBuffer(13), sslConnections(14), hosts(15), ipsecSessions(16), asdmSessions(17), sshSessions(18), telnetSessions(19), cpu(20), memory(21) } CiscoRateLimitResourceType ::= TEXTUAL-CONVENTION STATUS current DESCRIPTION "This object represents the resource type for which rate limiting needs to be done. The value for rate limiting is specified in crlRateLimitResourceMin and crlRateLimitResourceMax. The possible value(s) are : all (1) : This value represents a wildcard value to mean all the resources. arpRequestsXmt (2) : ARP requests generated per second arpResponses (3) : ARP responses to received ARP requests per second. bandwidth (4) : Bandwidth of the card in bytes per second. connections (5) : connections per second. appInspections (6) : application inspections per second. syslog (7) : syslog messages per second. sslBandwidth (8) : SSL bandwidth in bytes per second. sslConnections (9) : SSL connections per second. mgmtBandwidth (10): Management (to-the-ACE) traffic in bytes per second. throughput (11): User (through-the-ACE) traffic in bytes per second. missedMac (12): Number of ARP resolution requests in packets per second. httpCompression (13): Compression rate for HTTP traffic in bytes per second." SYNTAX INTEGER { all(1), arpRequestsXmt(2), arpResponses(3), bandwidth(4), connections(5), appInspections(6), syslog(7), sslBandwidth(8), sslConnections(9), mgmtBandwidth(10), throughput(11), missedMac(12), httpCompression(13) } CiscoResourceType ::= TEXTUAL-CONVENTION STATUS current DESCRIPTION "This object represents a resource type. The possible values for this object are: lMacAddresses (1) : Refer to 'macAddresses' in CiscoResourceLimitType. lConcurrentConns (2) : Refer to 'concurrentConns' in CiscoResourceLimitType. lMgmtConnections (3) : Refer to 'mgmtConnections' in CiscoResourceLimitType. lProxyConns (4) : Refer to 'proxyConns' in CiscoResourceLimitType. lProbes (5) : Refer to 'probes' in CiscoResourceLimitType. lStickyEntries (6) : Refer to 'stickyEntries' in CiscoResourceLimitType. lNatTranslations (7) : Refer to 'natTranslations' in CiscoResourceLimitType. lRegexState (8) : Refer to 'regexState' in CiscoResourceLimitType. lAclMemory (9) : Refer to 'aclMemory' in CiscoResourceLimitType. lIpReassemBuffer (10) : Refer to 'ipReassemBuffer' in CiscoResourceLimitType. lSyslogBuffer (11) : Refer to 'syslogBuffer' in CiscoResourceLimitType. lTcpOOOBuffer (12) : Refer to 'tcpOOOBuffer' in CiscoResourceLimitType. lSslConnections (13) : Refer to 'sslConnections' in CiscoResourceLimitType. lHosts (14) : Refer to 'hosts' in CiscoResourceLimitType. lIpsecSessions (15) : Refer to 'ipsecSessions' in CiscoResourceLimitType. lAsdmSessions (16) : Refer to 'asdmSessions' in CiscoResourceLimitType. lSshSessions (17) : Refer to 'sshSessions' in CiscoResourceLimitType. lTelnetSessions (18) : Refer to 'telnetSessions' in CiscoResourceLimitType. rlArpRequestsXmt (19) : Refer to 'arpRequestsXmt' in CiscoRateLimitResourceType. rlArpResponses (20) : Refer to 'arpResponses' in CiscoRateLimitResourceType. rlBandwidth (21) : Refer to 'bandwidth' in CiscoRateLimitResourceType. rlConnections (22) : Refer to 'connections' in CiscoRateLimitResourceType. rlAppInspections (23) : Refer to 'appInspections' in CiscoRateLimitResourceType. rlSyslog (24) : Refer to 'syslog' in CiscoRateLimitResourceType. rlSslBandwidth (25) : Refer to 'sslBandwidth' in CiscoRateLimitResourceType. rlSslConnections (26) : Refer to 'sslConnections' in CiscoRateLimitResourceType. rlMgmtBandwidth (27) : Refer to 'mgmtBandwidth' in CiscoRateLimitResourceType. rlThroughput (28) : Refer to 'throughput' in CiscoRateLimitResourceType. rlMissedMac (29) : Refer to 'missedMac' in CiscoRateLimitResourceType. rlHttpCompression (30) : Refer to 'httpCompression' in CiscoRateLimitResourceType." SYNTAX INTEGER { lMacAddresses(1), lConcurrentConns(2), lMgmtConnections(3), lProxyConns(4), lProbes(5), lStickyEntries(6), lNatTranslations(7), lRegexState(8), lAclMemory(9), lIpReassemBuffer(10), lSyslogBuffer(11), lTcpOOOBuffer(12), lSslConnections(13), lHosts(14), lIpsecSessions(15), lAsdmSessions(16), lSshSessions(17), lTelnetSessions(18), rlArpRequestsXmt(19), rlArpResponses(20), rlBandwidth(21), rlConnections(22), rlAppInspections(23), rlSyslog(24), rlSslBandwidth(25), rlSslConnections(26), rlMgmtBandwidth(27), rlThroughput(28), rlMissedMac(29), rlHttpCompression(30) } CiscoBufferUtilPercentage ::= TEXTUAL-CONVENTION DISPLAY-HINT "d-2" STATUS current DESCRIPTION "Buffer utilization as a percentage and should be presented in using xx.yy format." SYNTAX INTEGER (0..10000) ciscoL4L7ResourceClassTable OBJECT-TYPE SYNTAX SEQUENCE OF CiscoL4L7ResourceClassEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "This table contains one row per resource class. This table is used for adding/deleting the resource class in the system. A resource class can contain limits for different category of resources and these resources can be configured using other tables." ::= { crlResource 1 } ciscoL4L7ResourceClassEntry OBJECT-TYPE SYNTAX CiscoL4L7ResourceClassEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "Information about a particular resource class. Each entry provides the name of class. The entPhysicalIndex refers to resource manageable component in entPhysicalTable with entPhysicalClass -> 'module'." INDEX { entPhysicalIndex, crlResourceClassName } ::= { ciscoL4L7ResourceClassTable 1 } CiscoL4L7ResourceClassEntry ::= SEQUENCE { crlResourceClassName CiscoResourceClass, crlResourceClassStorageType StorageType, crlResourceClassRowStatus RowStatus } crlResourceClassName OBJECT-TYPE SYNTAX CiscoResourceClass MAX-ACCESS not-accessible STATUS current DESCRIPTION "This object identifies a unique resource class in a resource manageable component identified by entPhysicalIndex." ::= { ciscoL4L7ResourceClassEntry 1 } crlResourceClassStorageType OBJECT-TYPE SYNTAX StorageType MAX-ACCESS read-create STATUS current DESCRIPTION "The storage type for this conceptual row. Conceptual rows having the value 'permanent' need not allow write-access to any columnar objects in the row. This object can not be modified when the value of crlResourceClassRowStatus is 'active'." DEFVAL { nonVolatile } ::= { ciscoL4L7ResourceClassEntry 2 } crlResourceClassRowStatus OBJECT-TYPE SYNTAX RowStatus MAX-ACCESS read-create STATUS current DESCRIPTION "This object is used for adding/deleting resource classes in a system." ::= { ciscoL4L7ResourceClassEntry 3 } ciscoL4L7ResourceLimitTable OBJECT-TYPE SYNTAX SEQUENCE OF CiscoL4L7ResourceLimitEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "This table is used for adding resource limits to resources in a resource class." ::= { crlResource 2 } ciscoL4L7ResourceLimitEntry OBJECT-TYPE SYNTAX CiscoL4L7ResourceLimitEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "Information about a particular resource in a resource class. Each entry provides the type of resource, the limit that is supported for that resource and type of the limit value." INDEX { crlResourceClassName, crlResourceLimitType } ::= { ciscoL4L7ResourceLimitTable 1 } CiscoL4L7ResourceLimitEntry ::= SEQUENCE { crlResourceLimitType CiscoResourceLimitType, crlResourceLimitValueType INTEGER, crlResourceLimitMin Unsigned32, crlResourceLimitMax Unsigned32, crlResourceLimitStorageType StorageType, crlResourceLimitRowStatus RowStatus, crlResourceLimitCurrentUsage Gauge32, crlResourceLimitPeakUsage Gauge32, crlResourceLimitReqsDeniedCount Counter32 } crlResourceLimitType OBJECT-TYPE SYNTAX CiscoResourceLimitType MAX-ACCESS not-accessible STATUS current DESCRIPTION "This object represents the type of resource in a resource class identified by crlResourceClassName." ::= { ciscoL4L7ResourceLimitEntry 2 } crlResourceLimitValueType OBJECT-TYPE SYNTAX INTEGER { absolute(1), percentage(2) } MAX-ACCESS read-create STATUS current DESCRIPTION "This object represents the type of value specified in crlResourceLimitMax and crlResourceLimitMin objects. The possible values are : absolute (1) : the value represents an absolute number. percentage (2) : the value represents the % of the total available for the system. In this case only crlResourceLimitMax object is applicable." DEFVAL { percentage } ::= { ciscoL4L7ResourceLimitEntry 3 } crlResourceLimitMin OBJECT-TYPE SYNTAX Unsigned32 MAX-ACCESS read-create STATUS current DESCRIPTION "This object represents the rate limit allowed for the resource identified by 'ciscoResourceLimitType'. This value cannot be greater than the value specified in ciscoResourceLimitMax. The value zero signifies that this object is not applicable to the resource." DEFVAL { 0 } ::= { ciscoL4L7ResourceLimitEntry 4 } crlResourceLimitMax OBJECT-TYPE SYNTAX Unsigned32 MAX-ACCESS read-create STATUS current DESCRIPTION "This object represents the limit allowed for the resource identified by 'ciscoResourceLimitType'. The value zero specifies that this resource can be used until the system limit reached." DEFVAL { 0 } ::= { ciscoL4L7ResourceLimitEntry 5 } crlResourceLimitStorageType OBJECT-TYPE SYNTAX StorageType MAX-ACCESS read-create STATUS current DESCRIPTION "The storage type for this conceptual row. Conceptual rows having the value 'permanent' need not allow write-access to any columnar objects in the row. This object cannot be modified when the value of crlResourceLimitRowStatus is 'active'." DEFVAL { nonVolatile } ::= { ciscoL4L7ResourceLimitEntry 6 } crlResourceLimitRowStatus OBJECT-TYPE SYNTAX RowStatus MAX-ACCESS read-create STATUS current DESCRIPTION "This object is used for adding/deleting entries in this table." ::= { ciscoL4L7ResourceLimitEntry 7 } crlResourceLimitCurrentUsage OBJECT-TYPE SYNTAX Gauge32 MAX-ACCESS read-only STATUS current DESCRIPTION "This object indicates the number of resources identified by 'ciscoResourceLimitType', that are currently being used in the system." ::= { ciscoL4L7ResourceLimitEntry 8 } crlResourceLimitPeakUsage OBJECT-TYPE SYNTAX Gauge32 MAX-ACCESS read-only STATUS current DESCRIPTION "This object represents the peak usage of the resource identified by 'ciscoResourceLimitType' since the statistics were last cleared either through the command line interface or bacause of the system reboot." ::= { ciscoL4L7ResourceLimitEntry 9 } crlResourceLimitReqsDeniedCount OBJECT-TYPE SYNTAX Counter32 MAX-ACCESS read-only STATUS current DESCRIPTION "This object represents the number of resource requests that were denied when the configured resource limit is exceeded for the resource identified by 'ciscoResourceLimitType'. The value for resource limiting is specified in 'crlResourceLimitMax'." ::= { ciscoL4L7ResourceLimitEntry 10 } ciscoL4L7ResourceRateLimitTable OBJECT-TYPE SYNTAX SEQUENCE OF CiscoL4L7ResourceRateLimitEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "This table is used for adding/deleting the rate limiting of the resources in a resource class." ::= { crlResource 4 } ciscoL4L7ResourceRateLimitEntry OBJECT-TYPE SYNTAX CiscoL4L7ResourceRateLimitEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "Information about an entry in the table Each entry provides the name of group, the rate configured for a resource." INDEX { crlResourceClassName, crlRateLimitResourceType } ::= { ciscoL4L7ResourceRateLimitTable 1 } CiscoL4L7ResourceRateLimitEntry ::= SEQUENCE { crlRateLimitResourceType CiscoRateLimitResourceType, crlRateLimitResourceMin Unsigned32, crlRateLimitResourceMax Unsigned32, crlRateLimitResourceStorageType StorageType, crlRateLimitResourceRowStatus RowStatus, crlRateLimitResourceCurrentUsage Gauge32, crlRateLimitResourcePeakUsage Gauge32, crlRateLimitResourceReqsDeniedCount Counter32 } crlRateLimitResourceType OBJECT-TYPE SYNTAX CiscoRateLimitResourceType MAX-ACCESS not-accessible STATUS current DESCRIPTION "This object represents the resource type for which rate limiting needs to be done. The value for rate limiting is specified in crlRateLimitResourceMin and crlRateLimitResourceMax." ::= { ciscoL4L7ResourceRateLimitEntry 1 } crlRateLimitResourceMin OBJECT-TYPE SYNTAX Unsigned32 MAX-ACCESS read-create STATUS current DESCRIPTION "This object represents the rate limit allowed for the resource identified by 'crlRateLimitResourceType'. This value cannot be greater than the value specified in crlRateLimitResourceMax. The value zero signifies that this object is not applicable to the resource." DEFVAL { 0 } ::= { ciscoL4L7ResourceRateLimitEntry 2 } crlRateLimitResourceMax OBJECT-TYPE SYNTAX Unsigned32 MAX-ACCESS read-create STATUS current DESCRIPTION "This object represents the limit allowed for the resource identified by 'crlRateLimitResourceType'. The value zero specifies that this resource can be used until the system limit reached." DEFVAL { 0 } ::= { ciscoL4L7ResourceRateLimitEntry 3 } crlRateLimitResourceStorageType OBJECT-TYPE SYNTAX StorageType MAX-ACCESS read-create STATUS current DESCRIPTION "The storage type for this conceptual row. Conceptual rows having the value 'permanent' need not allow write-access to any columnar objects in the row. This object cannot be modified when the value of crlRateLimitResourceRowStatus is 'active'." DEFVAL { nonVolatile } ::= { ciscoL4L7ResourceRateLimitEntry 4 } crlRateLimitResourceRowStatus OBJECT-TYPE SYNTAX RowStatus MAX-ACCESS read-create STATUS current DESCRIPTION "This object is used for adding/deleting entries in this table. This object cannot be set to 'active' until all the mandatory objects have valid value." ::= { ciscoL4L7ResourceRateLimitEntry 5 } crlRateLimitResourceCurrentUsage OBJECT-TYPE SYNTAX Gauge32 MAX-ACCESS read-only STATUS current DESCRIPTION "This object indicates the number of resources identified by 'crlRateLimitResourceType', that are currently being used in the system." ::= { ciscoL4L7ResourceRateLimitEntry 6 } crlRateLimitResourcePeakUsage OBJECT-TYPE SYNTAX Gauge32 MAX-ACCESS read-only STATUS current DESCRIPTION "This object represents the peak usage of the resource identified by 'crlRateLimitResourceType' since the statistics were last cleared either through the command line interface or bacause of the system reboot." ::= { ciscoL4L7ResourceRateLimitEntry 7 } crlRateLimitResourceReqsDeniedCount OBJECT-TYPE SYNTAX Counter32 MAX-ACCESS read-only STATUS current DESCRIPTION "This object represents the number of resource requests that were denied when the configured rate limit is exceeded for the resource identified by 'crlRateLimitResourceType'. The value for rate limiting is specified in 'crlRateLimitResourceMax'." ::= { ciscoL4L7ResourceRateLimitEntry 8 } ciscoL4L7ResourceUsageSummaryTable OBJECT-TYPE SYNTAX SEQUENCE OF CiscoL4L7ResourceUsageSummaryEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "This table provides the statistics for each resource type in a system. The resource usage statistics can be: - current usage for the resource. - peak usage for the resource. - Number of times the resource request were denied when the configured limit or rate-limit is exceeded for the resource." ::= { crlResource 5 } ciscoL4L7ResourceUsageSummaryEntry OBJECT-TYPE SYNTAX CiscoL4L7ResourceUsageSummaryEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "An entry in ciscoL4L7ResourceUsageSummaryTable. Each entry provides the resource usage parameters in a system. An entry is created when an entry is created in either 'ciscoL4L7ResourceLimitTable' or 'ciscoL4L7ResourceRateLimitTable'. An entry is deleted when an entry is deleted from either 'ciscoL4L7ResourceLimitTable' or 'ciscoL4L7ResourceRateLimitTable'." INDEX { crlResourceSummaryType } ::= { ciscoL4L7ResourceUsageSummaryTable 1 } CiscoL4L7ResourceUsageSummaryEntry ::= SEQUENCE { crlResourceSummaryType CiscoResourceType, crlResourceSummaryCurrentUsage Gauge32, crlResourceSummaryPeakUsage Gauge32, crlResourceSummaryReqsDeniedCount Counter64, crlResourceSummaryLastClearedTime TimeStamp, crlResourceSummaryStorageType StorageType, crlResourceSummaryRowStatus RowStatus } crlResourceSummaryType OBJECT-TYPE SYNTAX CiscoResourceType MAX-ACCESS not-accessible STATUS current DESCRIPTION "This object represents a type of resource in the system." ::= { ciscoL4L7ResourceUsageSummaryEntry 1 } crlResourceSummaryCurrentUsage OBJECT-TYPE SYNTAX Gauge32 MAX-ACCESS read-only STATUS current DESCRIPTION "This object indicates the current usage of the resource in the system." ::= { ciscoL4L7ResourceUsageSummaryEntry 2 } crlResourceSummaryPeakUsage OBJECT-TYPE SYNTAX Gauge32 MAX-ACCESS read-only STATUS current DESCRIPTION "This object represents the peak usage of the resource in the system." ::= { ciscoL4L7ResourceUsageSummaryEntry 3 } crlResourceSummaryReqsDeniedCount OBJECT-TYPE SYNTAX Counter64 MAX-ACCESS read-only STATUS current DESCRIPTION "This object represents the number of resource requests that were denied in the system when the configured limit is exceeded for the resource. The value for limiting is specified in 'crlResourceLimitMax' and the value for rate limiting is specified in 'crlRateLimitResourceMax'." ::= { ciscoL4L7ResourceUsageSummaryEntry 4 } crlResourceSummaryLastClearedTime OBJECT-TYPE SYNTAX TimeStamp MAX-ACCESS read-only STATUS current DESCRIPTION "This object represents the time when the value of the object identified by 'crlResourceSummaryPeakUsage' is last cleared or reset. A value of 0 (zero) signifies that the value has not been cleared since the last system reboot." ::= { ciscoL4L7ResourceUsageSummaryEntry 5 } crlResourceSummaryStorageType OBJECT-TYPE SYNTAX StorageType MAX-ACCESS read-create STATUS current DESCRIPTION "The storage type for this conceptual row. Conceptual rows having the value 'permanent' need not allow write-access to any columnar objects in the row. This object cannot be modified when the value of 'crlResourceSummaryRowStatus' is 'active'." DEFVAL { nonVolatile } ::= { ciscoL4L7ResourceUsageSummaryEntry 6 } crlResourceSummaryRowStatus OBJECT-TYPE SYNTAX RowStatus MAX-ACCESS read-create STATUS current DESCRIPTION "This object is used for adding/deleting entries in this table. This object cannot be set to 'active' until all the mandatory objects have valid value." ::= { ciscoL4L7ResourceUsageSummaryEntry 7 } -- Add table description here ciscoL4L7BufferUtilizationTable OBJECT-TYPE SYNTAX SEQUENCE OF CiscoL4L7BufferUtilizationEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "This table provides the statistics for buffer utilization in a system. The buffer utilization statistics can be: - absolute buffer usage value per network processor(NP). - percentage buffer usage per network processor(NP)." ::= { crlResource 6 } ciscoL4L7BufferUtilizationEntry OBJECT-TYPE SYNTAX CiscoL4L7BufferUtilizationEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "An entry in ciscoL4L7BufferUtilizationTable. Each entry provides the buffer usage in a system." INDEX { clrNetworkProcessor } ::= { ciscoL4L7BufferUtilizationTable 1 } CiscoL4L7BufferUtilizationEntry ::= SEQUENCE { clrNetworkProcessor Unsigned32, crlBufferUsageValue Gauge32, crlPercentageBufferUsage CiscoBufferUtilPercentage, crlPercentageBufferUsageDisplay SnmpAdminString, crlExternalBufferUsageValue Gauge32, crlExternalPercentageBufferUsage CiscoBufferUtilPercentage, crlExternalPercentageBufferUsageDisplay SnmpAdminString } clrNetworkProcessor OBJECT-TYPE SYNTAX Unsigned32 MAX-ACCESS not-accessible STATUS current DESCRIPTION "This object represents network processor number(NP) in the system." ::= { ciscoL4L7BufferUtilizationEntry 1 } crlBufferUsageValue OBJECT-TYPE SYNTAX Gauge32 UNITS "buffers" MAX-ACCESS read-only STATUS current DESCRIPTION "This object indicates the absolute buffer usage in the system." ::= { ciscoL4L7BufferUtilizationEntry 2 } crlPercentageBufferUsage OBJECT-TYPE SYNTAX CiscoBufferUtilPercentage UNITS "percentage" MAX-ACCESS read-only STATUS current DESCRIPTION "This object represents the percentage buffer usage in the the decimal format to allow historical information to be collected." ::= { ciscoL4L7BufferUtilizationEntry 3 } crlPercentageBufferUsageDisplay OBJECT-TYPE SYNTAX SnmpAdminString UNITS "percentage" MAX-ACCESS read-only STATUS current DESCRIPTION "This object represents the percentage buffer usage in the string format to all interactive access to simple display format." ::= { ciscoL4L7BufferUtilizationEntry 4 } crlExternalBufferUsageValue OBJECT-TYPE SYNTAX Gauge32 UNITS "buffers" MAX-ACCESS read-only STATUS current DESCRIPTION "This object indicates the absolute external buffer usage in the system." ::= { ciscoL4L7BufferUtilizationEntry 5 } crlExternalPercentageBufferUsage OBJECT-TYPE SYNTAX CiscoBufferUtilPercentage UNITS "percentage" MAX-ACCESS read-only STATUS current DESCRIPTION "This object represents the percentage external buffer usage in the the decimal format to allow historical information to be collected." ::= { ciscoL4L7BufferUtilizationEntry 6 } crlExternalPercentageBufferUsageDisplay OBJECT-TYPE SYNTAX SnmpAdminString UNITS "percentage" MAX-ACCESS read-only STATUS current DESCRIPTION "This object represents the percentage external buffer usage in the string format to all interactive access to simple display format." ::= { ciscoL4L7BufferUtilizationEntry 7 } -- CPU UtilizationTable per NP ciscoL4L7NpCpuUtilTable OBJECT-TYPE SYNTAX SEQUENCE OF CiscoL4L7NpCpuUtilEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "This table lists the CPU utilization statistics for each NP (network processor) in the device." ::= { crlResource 7 } ciscoL4L7NpCpuUtilEntry OBJECT-TYPE SYNTAX CiscoL4L7NpCpuUtilEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "Each row contains the average CPU utilization of all sub-processors for a network processor identified by its clrNetworkProcessor value." INDEX { clrNetworkProcessor } ::= { ciscoL4L7NpCpuUtilTable 1 } CiscoL4L7NpCpuUtilEntry ::= SEQUENCE { clrNpCpuUtilizationAverage Gauge32 } clrNpCpuUtilizationAverage OBJECT-TYPE SYNTAX Gauge32 MAX-ACCESS read-only STATUS current DESCRIPTION "This object indicates the average CPU utilization of all sub-processors belonged to a particular network processor at that instance." ::= { ciscoL4L7NpCpuUtilEntry 1 } -- notification control objects clrResourceLimitReachedNotifEnabled OBJECT-TYPE SYNTAX TruthValue MAX-ACCESS read-write STATUS current DESCRIPTION "This object controls the generation of 'clrResourceLimitReachedNotifRev1' notification. 'true' Indicates that clrResourceLimitReachedNotifRev1 notification is to be generated when the configured resource limit is reached. 'false' Indicates that clrResourceLimitReachedNotifRev1 notification generation is disabled." DEFVAL { false } ::= { crlNotificationObjects 1 } clrResourceRateLimitReachedNotifEnabled OBJECT-TYPE SYNTAX TruthValue MAX-ACCESS read-write STATUS current DESCRIPTION "This object controls the generation of 'clrResourceRateLimitReachedNotifRev1' notification. 'true' Indicates that clrResourceRateLimitReachedNotifRev1 notification is to be generated when the configured resource rate limit is reached. 'false' Indicates that clrResourceRateLimitReachedNotifRev1 notification generation is disabled." DEFVAL { false } ::= { crlNotificationObjects 2 } crlNotifType OBJECT-TYPE SYNTAX INTEGER { risingHighThresh(1), -- Notification to indicate -- that the current usage -- exceeds the high threshold fallingMinThresh(2), -- Notification to indicate -- that the current usage -- falls below the minimal threshold fallingWatermarkThresh(3), -- Notification to -- indicate that the -- current usage falls -- below the high -- watermark threshold risingWatermarkThresh(4) -- Notification to -- indicate that the -- current usage exceeds -- the low watermark -- threshold } MAX-ACCESS accessible-for-notify STATUS current DESCRIPTION "This object indicates type of notification." ::= { crlNotificationOnlyObjects 1 } crlNotifContextOrSystem OBJECT-TYPE SYNTAX INTEGER { system(1), context(2) } MAX-ACCESS accessible-for-notify STATUS current DESCRIPTION "This object indicates the notification sent is at the system level or at the context level." ::= { crlNotificationOnlyObjects 2 } crlNotifContextName OBJECT-TYPE SYNTAX SnmpAdminString MAX-ACCESS accessible-for-notify STATUS current DESCRIPTION "This object indicates the context name associated with notifications." ::= { crlNotificationOnlyObjects 3 } crlNotifCurrentUsagePcnt OBJECT-TYPE SYNTAX Unsigned32 UNITS "percent" MAX-ACCESS accessible-for-notify STATUS current DESCRIPTION "This object indicates the current usage percent of the resource associated with notifications." ::= { crlNotificationOnlyObjects 4 } crlNotifMaxThresholdPcnt OBJECT-TYPE SYNTAX Unsigned32 (0..100) UNITS "percent" MAX-ACCESS accessible-for-notify STATUS current DESCRIPTION "This object indicates the maximum threshold percent of the resource/rate associated with notifications. This object is used to raise the risingHighThresh notification when the current usage identified by crlNotifCurrentUsagePcnt exceeds maximum threshold identified by crlNotifMaxThresholdPcnt." ::= { crlNotificationOnlyObjects 5 } crlNotifWatermarkPcnt OBJECT-TYPE SYNTAX Unsigned32 (0..100) UNITS "percent" MAX-ACCESS accessible-for-notify STATUS current DESCRIPTION "This object indicates the watermark threshold percent of the resource/rate associated with notifications. This object is used to raise the risingWatermarkThresh/fallingWatermarkThresh notifications when the current usage identified by crlNotifCurrentUsagePcnt exceeds high or falls below watermark threshold identified by crlNotifWatermarkPcnt." ::= { crlNotificationOnlyObjects 6 } crlNotifMinThresholdPcnt OBJECT-TYPE SYNTAX Unsigned32 (0..100) UNITS "percent" MAX-ACCESS accessible-for-notify STATUS current DESCRIPTION "This object indicates the minimum threshold percent of the resource/rate associated with notifications. This object is used to raise the fallingWatermarkThresh notification when the current usage identified by crlNotifCurrentUsagePcnt falls below minimum threshold identified by crlNotifMinThresholdPcnt." ::= { crlNotificationOnlyObjects 7 } crlNotifSourceType OBJECT-TYPE SYNTAX INTEGER { virtualIP(1), -- Object to indicate that the -- -- notification is being raised for -- virtual ip realServer(2) -- Object to indicate that the -- -- notification is being raised for -- real server } MAX-ACCESS accessible-for-notify STATUS current DESCRIPTION "This object indicates the notification sent is at the real server level or at virtual ip level. Rserver is a real server e.g. a linux machine which services the client requests. Virtual IP is a IP address which is advertised to the outside world from the Data Center for communication with the server." ::= { crlNotificationOnlyObjects 8 } crlNotifRealServerName OBJECT-TYPE SYNTAX SnmpAdminString MAX-ACCESS accessible-for-notify STATUS current DESCRIPTION "This object indicates the real server name associated with notifications." ::= { crlNotificationOnlyObjects 9 } crlNotifVirtualIPAddrType OBJECT-TYPE SYNTAX InetAddressType MAX-ACCESS accessible-for-notify STATUS current DESCRIPTION "This object indicates type of the Virtual IP address i.e. IPv4 or IPv6." ::= { crlNotificationOnlyObjects 10 } crlNotifVirtualIPAddress OBJECT-TYPE SYNTAX InetAddress MAX-ACCESS accessible-for-notify STATUS current DESCRIPTION "This object indicates the Virtual IP (VIP) Adress associated with notifications." ::= { crlNotificationOnlyObjects 11 } -- notifications clrResourceLimitReached NOTIFICATION-TYPE OBJECTS { crlResourceLimitValueType, crlResourceLimitMax } STATUS deprecated DESCRIPTION "This notification is generated when the configured resource limit value specified in 'crlResourceLimitMax' is reached for a particular resource. This resource is identified by 'crlResourceLimitType' in ciscoL4L7ResourceLimitTable. clrResourceLimitReached object is superseded by clrResourceLimitReachedNotif." ::= { ciscoL4L7ResourceLimitNotifs 1 } clrResourceRateLimitReached NOTIFICATION-TYPE OBJECTS { crlRateLimitResourceMax } STATUS deprecated DESCRIPTION "This notification is generated when the configured rate limit value specified in 'crlRateLimitResourceMax' is reached for a particular resource. This resource is identified by 'crlRateLimitResourceType' in ciscoL4L7ResourceRateLimitTable. clrResourceRateLimitReached object is superseded by clrResourceRateLimitReachedNotif." ::= { ciscoL4L7ResourceLimitNotifs 2 } clrResourceLimitReachedNotif NOTIFICATION-TYPE OBJECTS { crlNotifType, crlResourceLimitCurrentUsage, crlResourceLimitMax, crlResourceLimitMin, crlNotifCurrentUsagePcnt, crlNotifMaxThresholdPcnt, crlNotifWatermarkPcnt, crlNotifMinThresholdPcnt, crlNotifContextOrSystem, crlNotifContextName } STATUS deprecated DESCRIPTION "The notification will be generated when the current resource usage identified by crlResourceLimitCurrentUsage exceeds/falls below the user configured thresholds identified by crlNotifMaxThresholdPcnt, crlNotifMinThresholdPcnt and crlNotifWatermarkPcnt. Notifications will be generated on the following conditions 1. crlResourceLimitCurrentUsage exceeds crlNotifMaxThresholdPcnt 2. crlResourceLimitCurrentUsage falls below high crlNotifWatermarkPcnt 3. crlResourceLimitCurrentUsage falls below crlNotifMinThresholdPcnt 4. crlResourceLimitCurrentUsage exceeds low crlNotifWatermarkPcnt. clrResourceLimitReachedNotif object is superseded by clrResourceLimitReachedNotifRev1." ::= { ciscoL4L7ResourceLimitNotifs 3 } clrResourceRateLimitReachedNotif NOTIFICATION-TYPE OBJECTS { crlNotifType, crlRateLimitResourceCurrentUsage, crlRateLimitResourceMax, crlRateLimitResourceMin, crlNotifCurrentUsagePcnt, crlNotifMaxThresholdPcnt, crlNotifWatermarkPcnt, crlNotifMinThresholdPcnt, crlNotifContextOrSystem, crlNotifContextName } STATUS deprecated DESCRIPTION "The notification will be generated when the current resource rate usage identified by crlResourceRateLimitCurrentUsage exceeds/falls below the user configured thresholds identified by crlNotifMaxThresholdPcnt, crlNotifMinThresholdPcnt and crlNotifWatermarkPcnt. Notifications will be generated on the following conditions 1. crlResourceRateLimitCurrentUsage exceeds crlNotifMaxThresholdPcnt 2. crlResourceRateLimitCurrentUsage falls below high crlNotifWatermarkPcnt 3. crlResourceRateLimitCurrentUsage falls below crlNotifMinThresholdPcnt 4. crlResourceRateLimitCurrentUsage exceeds low crlNotifWatermarkPcnt clrResourceRateLimitReachedNotif object is superseded by clrResourceRateLimitReachedNotifRev1." ::= { ciscoL4L7ResourceLimitNotifs 4 } clrResourceRateLimitReachedNotifRev1 NOTIFICATION-TYPE OBJECTS { crlNotifType, crlRateLimitResourceCurrentUsage, crlRateLimitResourceMax, crlRateLimitResourceMin, crlNotifCurrentUsagePcnt, crlNotifMaxThresholdPcnt, crlNotifWatermarkPcnt, crlNotifMinThresholdPcnt, crlNotifContextOrSystem, crlNotifContextName, crlNotifSourceType, crlNotifRealServerName, crlNotifVirtualIPAddrType, crlNotifVirtualIPAddress } STATUS current DESCRIPTION "The notification will be generated when the current resource usage rate identified by crlResourceRateLimitCurrentUsage exceeds/falls below the user configured thresholds identified by crlNotifMaxThresholdPcnt, crlNotifMinThresholdPcnt and crlNotifWatermarkPcnt. Notifications will be generated on the following conditions 1. crlResourceRateLimitCurrentUsage exceeds crlNotifMaxThresholdPcnt 2. crlResourceRateLimitCurrentUsage falls below high crlNotifWatermarkPcnt 3. crlResourceRateLimitCurrentUsage falls below crlNotifMinThresholdPcnt 4. crlResourceRateLimitCurrentUsage exceeds low crlNotifWatermarkPcnt" ::= { ciscoL4L7ResourceLimitNotifs 5 } clrResourceLimitReachedNotifRev1 NOTIFICATION-TYPE OBJECTS { crlNotifType, crlResourceLimitCurrentUsage, crlResourceLimitMax, crlResourceLimitMin, crlNotifCurrentUsagePcnt, crlNotifMaxThresholdPcnt, crlNotifWatermarkPcnt, crlNotifMinThresholdPcnt, crlNotifContextOrSystem, crlNotifContextName, crlNotifSourceType, crlNotifRealServerName, crlNotifVirtualIPAddrType, crlNotifVirtualIPAddress } STATUS current DESCRIPTION "The notification will be generated when the current resource usage identified by crlResourceLimitCurrentUsage exceeds/falls below the user configured thresholds identified by crlNotifMaxThresholdPcnt, crlNotifMinThresholdPcnt and crlNotifWatermarkPcnt. Notifications will be generated on the following conditions 1. crlResourceLimitCurrentUsage exceeds crlNotifMaxThresholdPcnt 2. crlResourceLimitCurrentUsage falls below high crlNotifWatermarkPcnt 3. crlResourceLimitCurrentUsage falls below crlNotifMinThresholdPcnt 4. crlResourceLimitCurrentUsage exceeds low crlNotifWatermarkPcnt." ::= { ciscoL4L7ResourceLimitNotifs 6 } -- conformance information ciscoL4L7ResourceLimitConformance OBJECT IDENTIFIER ::= { ciscoL4L7moduleResourceLimitMIB 3 } ciscoL4L7ResourceLimitCompliances OBJECT IDENTIFIER ::= { ciscoL4L7ResourceLimitConformance 1 } ciscoL4L7ResourceLimitGroups OBJECT IDENTIFIER ::= { ciscoL4L7ResourceLimitConformance 2 } -- compliance statements ciscoL4L7ResourceLimitCompliance MODULE-COMPLIANCE STATUS deprecated DESCRIPTION "The compliance statement for SNMP entities which implement CISCO-L4L7MODULE-RESOURCE-LIMIT-MIB." MODULE -- this module MANDATORY-GROUPS { ciscoL4L7ResourceClassGroup, ciscoL4L7ResourceLimitGroup } GROUP ciscoL4L7ResourceRateLimitGroup DESCRIPTION "This group is mandatory for those systems where rate limiting is supported." ::= { ciscoL4L7ResourceLimitCompliances 1 } ciscoL4L7ResourceLimitComplianceRev1 MODULE-COMPLIANCE STATUS deprecated DESCRIPTION "The compliance statement for SNMP entities which implement CISCO-L4L7MODULE-RESOURCE-LIMIT-MIB." MODULE -- this module MANDATORY-GROUPS { ciscoL4L7ResourceClassGroup, ciscoL4L7ResourceLimitGroup, ciscoL4L7ResourceLimitUsageGroup } GROUP ciscoL4L7ResourceRateLimitGroup DESCRIPTION "This group is mandatory for those systems where rate limiting is supported." GROUP ciscoL4L7ResourceRateLimitUsageGroup DESCRIPTION "This group is mandatory for those systems where rate limiting is supported." GROUP ciscoL4L7ResourceNotifEnabledGroup DESCRIPTION "This group is mandatory for those systems which implement resource limit notifications." GROUP ciscoL4L7ResourceNotifGroup DESCRIPTION "This group is mandatory for those systems which implement resource limit notifications." ::= { ciscoL4L7ResourceLimitCompliances 2 } ciscoL4L7ResourceLimitComplianceRev2 MODULE-COMPLIANCE STATUS deprecated DESCRIPTION "The compliance statement for SNMP entities which implement CISCO-L4L7MODULE-RESOURCE-LIMIT-MIB." MODULE -- this module MANDATORY-GROUPS { ciscoL4L7ResourceClassGroup, ciscoL4L7ResourceLimitGroup, ciscoL4L7ResourceLimitUsageGroup } GROUP ciscoL4L7ResourceRateLimitGroup DESCRIPTION "This group is mandatory for those systems where rate limiting is supported." GROUP ciscoL4L7ResourceRateLimitUsageGroup DESCRIPTION "This group is mandatory for those systems where rate limiting is supported." GROUP ciscoL4L7ResourceNotifEnabledGroup DESCRIPTION "This group is mandatory for those systems which implement resource limit notifications." GROUP ciscoL4L7ResourceNotifGroup DESCRIPTION "This group is mandatory for those systems which implement resource limit notifications." GROUP ciscoL4L7ResourceUsageSummaryGroup DESCRIPTION "This group is mandatory for those systems which implement resource limiting and/or rate limiting of resource." ::= { ciscoL4L7ResourceLimitCompliances 3 } ciscoL4L7ResourceLimitComplianceRev3 MODULE-COMPLIANCE STATUS deprecated DESCRIPTION "The compliance statement for SNMP entities which implement CISCO-L4L7MODULE-RESOURCE-LIMIT-MIB." MODULE -- this module MANDATORY-GROUPS { ciscoL4L7ResourceClassGroup, ciscoL4L7ResourceLimitGroup, ciscoL4L7ResourceLimitUsageGroup, ciscoL4L7BufferUtilizationGroup } GROUP ciscoL4L7ResourceRateLimitGroup DESCRIPTION "This group is mandatory for those systems where rate limiting is supported." GROUP ciscoL4L7ResourceRateLimitUsageGroup DESCRIPTION "This group is mandatory for those systems where rate limiting is supported." GROUP ciscoL4L7ResourceNotifEnabledGroup DESCRIPTION "This group is mandatory for those systems which implement resource limit notifications." GROUP ciscoL4L7ResourceNotifGroup DESCRIPTION "This group is mandatory for those systems which implement resource limit notifications." GROUP ciscoL4L7ResourceUsageSummaryGroup DESCRIPTION "This group is mandatory for those systems which implement resource limiting and/or rate limiting of resource." ::= { ciscoL4L7ResourceLimitCompliances 4 } ciscoL4L7ResourceLimitComplianceRev4 MODULE-COMPLIANCE STATUS deprecated DESCRIPTION "The compliance statement for SNMP entities which implement CISCO-L4L7MODULE-RESOURCE-LIMIT-MIB." MODULE -- this module MANDATORY-GROUPS { ciscoL4L7ResourceClassGroup, ciscoL4L7ResourceLimitGroup, ciscoL4L7ResourceLimitUsageGroup, ciscoL4L7BufferUtilizationGroup } GROUP ciscoL4L7NpCpuUtilizationGroup DESCRIPTION "The ciscoL4L7NpCpuUtilizationGroup is optional and gives the CPU utilization of network processors." GROUP ciscoL4L7ResourceRateLimitGroup DESCRIPTION "This group is mandatory for those systems where rate limiting is supported." GROUP ciscoL4L7ResourceRateLimitUsageGroup DESCRIPTION "This group is mandatory for those systems where rate limiting is supported." GROUP ciscoL4L7ResourceNotifEnabledGroup DESCRIPTION "This group is mandatory for those systems which implement resource limit notifications." GROUP ciscoL4L7ResourceNotifGroup DESCRIPTION "This group is mandatory for those systems which implement resource limit notifications." GROUP ciscoL4L7ResourceUsageSummaryGroup DESCRIPTION "This group is mandatory for those systems which implement resource limiting and/or rate limiting of resource." ::= { ciscoL4L7ResourceLimitCompliances 5 } ciscoL4L7ResourceLimitComplianceRev5 MODULE-COMPLIANCE STATUS deprecated DESCRIPTION "The compliance statement for SNMP entities which implement CISCO-L4L7MODULE-RESOURCE-LIMIT-MIB." MODULE -- this module MANDATORY-GROUPS { ciscoL4L7ResourceClassGroup, ciscoL4L7ResourceLimitGroup, ciscoL4L7ResourceLimitUsageGroup, ciscoL4L7BufferUtilizationGroupRev1 } GROUP ciscoL4L7NpCpuUtilizationGroup DESCRIPTION "The ciscoL4L7NpCpuUtilizationGroup is optional and gives the CPU utilization of network processors." GROUP ciscoL4L7ResourceRateLimitGroup DESCRIPTION "This group is mandatory for those systems where rate limiting is supported." GROUP ciscoL4L7ResourceRateLimitUsageGroup DESCRIPTION "This group is mandatory for those systems where rate limiting is supported." GROUP ciscoL4L7ResourceNotifEnabledGroup DESCRIPTION "This group is mandatory for those systems which implement resource limit notifications." GROUP ciscoL4L7ResourceNotifGroup DESCRIPTION "This group is mandatory for those systems which implement resource limit notifications." GROUP ciscoL4L7ResourceUsageSummaryGroup DESCRIPTION "This group is mandatory for those systems which implement resource limiting and/or rate limiting of resource." ::= { ciscoL4L7ResourceLimitCompliances 6 } ciscoL4L7ResourceLimitComplianceRev6 MODULE-COMPLIANCE STATUS deprecated DESCRIPTION "The compliance statement for SNMP entities which implement CISCO-L4L7MODULE-RESOURCE-LIMIT-MIB." MODULE -- this module MANDATORY-GROUPS { ciscoL4L7ResourceClassGroup, ciscoL4L7ResourceLimitGroup, ciscoL4L7ResourceLimitUsageGroup, ciscoL4L7BufferUtilizationGroupRev1 } GROUP ciscoL4L7NpCpuUtilizationGroup DESCRIPTION "The ciscoL4L7NpCpuUtilizationGroup is optional and gives the CPU utilization of network processors." GROUP ciscoL4L7ResourceRateLimitGroup DESCRIPTION "This group is mandatory for those systems where rate limiting is supported." GROUP ciscoL4L7ResourceRateLimitUsageGroup DESCRIPTION "This group is mandatory for those systems where rate limiting is supported." GROUP ciscoL4L7ResourceNotifEnabledGroup DESCRIPTION "This group is mandatory for those systems which implement resource limit notifications." GROUP ciscoL4L7ResourceUsageSummaryGroup DESCRIPTION "This group is mandatory for those systems which implement resource limiting and/or rate limiting of resource." GROUP ciscoL4L7ResourceNotifOnlyObjectsGroup DESCRIPTION "This group is mandatory for those systems which implement ciscoL4L7ResourceNotifGroupRev1." ::= { ciscoL4L7ResourceLimitCompliances 7 } ciscoL4L7ResourceLimitComplianceRev7 MODULE-COMPLIANCE STATUS current DESCRIPTION "The compliance statement for SNMP entities which implement CISCO-L4L7MODULE-RESOURCE-LIMIT-MIB." MODULE -- this module MANDATORY-GROUPS { ciscoL4L7ResourceClassGroup, ciscoL4L7ResourceLimitGroup, ciscoL4L7ResourceLimitUsageGroup, ciscoL4L7BufferUtilizationGroupRev1 } GROUP ciscoL4L7NpCpuUtilizationGroup DESCRIPTION "The ciscoL4L7NpCpuUtilizationGroup is optional and gives the CPU utilization of network processors." GROUP ciscoL4L7ResourceRateLimitGroup DESCRIPTION "This group is mandatory for those systems where rate limiting is supported." GROUP ciscoL4L7ResourceRateLimitUsageGroup DESCRIPTION "This group is mandatory for those systems where rate limiting is supported." GROUP ciscoL4L7ResourceNotifEnabledGroup DESCRIPTION "This group is mandatory for those systems which implement resource limit notifications." GROUP ciscoL4L7ResourceUsageSummaryGroup DESCRIPTION "This group is mandatory for those systems which implement resource limiting and/or rate limiting of resource." GROUP ciscoL4L7ResourceNotifOnlyObjectsGroup DESCRIPTION "This group is mandatory for those systems which implement ciscoL4L7ResourceNotifGroupRev1." GROUP ciscoL4L7ResourceNotifOnlyObjectsGroupExt DESCRIPTION "This group is mandatory for those systems which implements ciscoL4L7ResourceNotifGroupRev2." GROUP ciscoL4L7ResourceNotifGroupRev2 DESCRIPTION "This group is optional and these traps indicates that configured threshold is reached." ::= { ciscoL4L7ResourceLimitCompliances 8 } -- MIB groupings ciscoL4L7ResourceClassGroup OBJECT-GROUP OBJECTS { crlResourceClassStorageType, crlResourceClassRowStatus } STATUS current DESCRIPTION "The collection of objects which are used to represent resource class in a system." ::= { ciscoL4L7ResourceLimitGroups 1 } ciscoL4L7ResourceLimitGroup OBJECT-GROUP OBJECTS { crlResourceLimitValueType, crlResourceLimitMin, crlResourceLimitMax, crlResourceLimitStorageType, crlResourceLimitRowStatus } STATUS current DESCRIPTION "The collection of objects which are used to represent limits of resources in a resource class." ::= { ciscoL4L7ResourceLimitGroups 2 } ciscoL4L7ResourceRateLimitGroup OBJECT-GROUP OBJECTS { crlRateLimitResourceMin, crlRateLimitResourceMax, crlRateLimitResourceStorageType, crlRateLimitResourceRowStatus } STATUS current DESCRIPTION "The collection of objects which are used to represent rate limits for resources." ::= { ciscoL4L7ResourceLimitGroups 3 } ciscoL4L7ResourceLimitUsageGroup OBJECT-GROUP OBJECTS { crlResourceLimitCurrentUsage, crlResourceLimitPeakUsage, crlResourceLimitReqsDeniedCount } STATUS current DESCRIPTION "The collection of objects which are used to represent limit usage for resources." ::= { ciscoL4L7ResourceLimitGroups 4 } ciscoL4L7ResourceRateLimitUsageGroup OBJECT-GROUP OBJECTS { crlRateLimitResourceCurrentUsage, crlRateLimitResourcePeakUsage, crlRateLimitResourceReqsDeniedCount } STATUS current DESCRIPTION "The collection of objects which are used to represent rate limit usage for resources." ::= { ciscoL4L7ResourceLimitGroups 5 } ciscoL4L7ResourceNotifEnabledGroup OBJECT-GROUP OBJECTS { clrResourceLimitReachedNotifEnabled, clrResourceRateLimitReachedNotifEnabled } STATUS current DESCRIPTION "The collection of objects which are used to represent limit usage for resources." ::= { ciscoL4L7ResourceLimitGroups 6 } ciscoL4L7ResourceNotifGroup NOTIFICATION-GROUP NOTIFICATIONS { clrResourceLimitReached, clrResourceRateLimitReached } STATUS deprecated DESCRIPTION "The collection of objects which are used to represent rate limit usage for resources. ciscoL4L7ResourceNotifGroup object is superseded by ciscoL4L7ResourceNotifGroupRev1." ::= { ciscoL4L7ResourceLimitGroups 7 } ciscoL4L7ResourceUsageSummaryGroup OBJECT-GROUP OBJECTS { crlResourceSummaryCurrentUsage, crlResourceSummaryPeakUsage, crlResourceSummaryReqsDeniedCount, crlResourceSummaryLastClearedTime, crlResourceSummaryStorageType, crlResourceSummaryRowStatus } STATUS current DESCRIPTION "The collection of objects which are used to represent usage summary for resources across the system." ::= { ciscoL4L7ResourceLimitGroups 8 } ciscoL4L7BufferUtilizationGroup OBJECT-GROUP OBJECTS { crlBufferUsageValue, crlPercentageBufferUsage, crlPercentageBufferUsageDisplay } STATUS deprecated DESCRIPTION "The collection of objects which are used to represent buffer utilization across the system. ciscoL4L7BufferUtilizationGroup object is superseded by ciscoL4L7BufferUtilizationGroupRev1." ::= { ciscoL4L7ResourceLimitGroups 9 } ciscoL4L7NpCpuUtilizationGroup OBJECT-GROUP OBJECTS { clrNpCpuUtilizationAverage } STATUS current DESCRIPTION "A collection of objects providing CPU utilization of network processors." ::= { ciscoL4L7ResourceLimitGroups 10 } ciscoL4L7BufferUtilizationGroupRev1 OBJECT-GROUP OBJECTS { crlBufferUsageValue, crlPercentageBufferUsage, crlPercentageBufferUsageDisplay, crlExternalBufferUsageValue, crlExternalPercentageBufferUsage, crlExternalPercentageBufferUsageDisplay } STATUS current DESCRIPTION "The collection of objects which are used to represent buffer utilization across the system." ::= { ciscoL4L7ResourceLimitGroups 11 } ciscoL4L7ResourceNotifGroupRev1 NOTIFICATION-GROUP NOTIFICATIONS { clrResourceLimitReachedNotif, clrResourceRateLimitReachedNotif } STATUS deprecated DESCRIPTION "The collection of notifications which are used to report resources usages to raising/falling below the configured thresholds. ciscoL4L7ResourceNotifGroupRev1 object is superseded by ciscoL4L7ResourceNotifGroupRev2." ::= { ciscoL4L7ResourceLimitGroups 12 } ciscoL4L7ResourceNotifOnlyObjectsGroup OBJECT-GROUP OBJECTS { crlNotifType, crlNotifCurrentUsagePcnt, crlNotifMaxThresholdPcnt, crlNotifWatermarkPcnt, crlNotifMinThresholdPcnt, crlNotifContextOrSystem, crlNotifContextName } STATUS current DESCRIPTION "A collection of object(s) providing variable binding information for resource notifications." ::= { ciscoL4L7ResourceLimitGroups 13 } ciscoL4L7ResourceNotifGroupRev2 NOTIFICATION-GROUP NOTIFICATIONS { clrResourceLimitReachedNotifRev1, clrResourceRateLimitReachedNotifRev1 } STATUS current DESCRIPTION "The collection of notifications which are used to report resources usages to raising/falling below the configured thresholds." ::= { ciscoL4L7ResourceLimitGroups 14 } ciscoL4L7ResourceNotifOnlyObjectsGroupExt OBJECT-GROUP OBJECTS { crlNotifSourceType, crlNotifRealServerName, crlNotifVirtualIPAddrType, crlNotifVirtualIPAddress } STATUS current DESCRIPTION "A collection of object(s) providing variable binding information for resource notifications." ::= { ciscoL4L7ResourceLimitGroups 15 } END