-- ***************************************************************** -- CISCO-IPSLA-ECHO-MIB.my: IP SLA MIB for udp echo, icmp echo -- and tcp connect operations templates -- -- November 2006, Katherine Yang -- -- Copyright (c) 2006-2007 by cisco Systems Inc. -- All rights reserved. -- -- **************************************************************** CISCO-IPSLA-ECHO-MIB DEFINITIONS ::= BEGIN IMPORTS MODULE-IDENTITY, OBJECT-TYPE, Unsigned32 FROM SNMPv2-SMI MODULE-COMPLIANCE, OBJECT-GROUP FROM SNMPv2-CONF StorageType, TruthValue, RowStatus FROM SNMPv2-TC SnmpAdminString FROM SNMP-FRAMEWORK-MIB InetAddress, InetAddressType, InetPortNumber FROM INET-ADDRESS-MIB ciscoMgmt FROM CISCO-SMI; ciscoIpSlaEchoMIB MODULE-IDENTITY LAST-UPDATED "200708160000Z" ORGANIZATION "Cisco Systems, Inc." CONTACT-INFO "Cisco Systems, Inc. Customer Service Postal: 170 W Tasman Drive San Jose, CA 95134 Tel: +1 800 553 NETS Email: cs-ipsla@cisco.com" DESCRIPTION "This MIB module defines the templates for IP SLA operations of ICMP echo, UDP echo and TCP connect. The ICMP echo operation measures end-to-end response time between a Cisco router and any IP enabled device by computing the time taken between sending an ICMP echo request message to the destination and receiving an ICMP echo reply. The UDP echo operation measures end-to-end response time between a Cisco router and any IP enabled device by computing the time taken between sending an UDP echo request message to the destination and receiving an UDP echo reply. The TCP connect operation measures end-to-end response time between a Cisco router and any IP enabled device by computing the time taken to perform a TCP connect operation." REVISION "200708160000Z" DESCRIPTION "Initial version of this MIB module." ::= { ciscoMgmt 636 } ciscoIpSlaEchoMIBNotifs OBJECT IDENTIFIER ::= { ciscoIpSlaEchoMIB 0 } ciscoIpSlaEchoMIBObjects OBJECT IDENTIFIER ::= { ciscoIpSlaEchoMIB 1 } cipslaIcmpEchoTmplTable OBJECT-TYPE SYNTAX SEQUENCE OF CipslaIcmpEchoTmplEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "A table that contains ICMP echo template definitions." ::= { ciscoIpSlaEchoMIBObjects 1 } cipslaIcmpEchoTmplEntry OBJECT-TYPE SYNTAX CipslaIcmpEchoTmplEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "A row entry representing an IPSLA ICMP echo template." INDEX { cipslaIcmpEchoTmplName } ::= { cipslaIcmpEchoTmplTable 1 } CipslaIcmpEchoTmplEntry ::= SEQUENCE { cipslaIcmpEchoTmplName SnmpAdminString, cipslaIcmpEchoTmplDescription SnmpAdminString, cipslaIcmpEchoTmplSrcAddrType InetAddressType, cipslaIcmpEchoTmplSrcAddr InetAddress, cipslaIcmpEchoTmplTimeOut Unsigned32, cipslaIcmpEchoTmplVerifyData TruthValue, cipslaIcmpEchoTmplReqDataSize Unsigned32, cipslaIcmpEchoTmplTOS Unsigned32, cipslaIcmpEchoTmplVrfName SnmpAdminString, cipslaIcmpEchoTmplThreshold Unsigned32, cipslaIcmpEchoTmplHistLives Unsigned32, cipslaIcmpEchoTmplHistBuckets Unsigned32, cipslaIcmpEchoTmplHistFilter INTEGER , cipslaIcmpEchoTmplStatsHours Unsigned32, cipslaIcmpEchoTmplDistBuckets Unsigned32, cipslaIcmpEchoTmplDistInterval Unsigned32, cipslaIcmpEchoTmplStorageType StorageType, cipslaIcmpEchoTmplRowStatus RowStatus } cipslaIcmpEchoTmplName OBJECT-TYPE SYNTAX SnmpAdminString (SIZE (1..64)) MAX-ACCESS not-accessible STATUS current DESCRIPTION "This field is used to specify the ICMP echo template name." ::= { cipslaIcmpEchoTmplEntry 1 } cipslaIcmpEchoTmplDescription OBJECT-TYPE SYNTAX SnmpAdminString (SIZE (0..128)) MAX-ACCESS read-create STATUS current DESCRIPTION "This field is used to provide description for the ICMP echo template." DEFVAL { "" } ::= { cipslaIcmpEchoTmplEntry 2 } cipslaIcmpEchoTmplSrcAddrType OBJECT-TYPE SYNTAX InetAddressType MAX-ACCESS read-create STATUS current DESCRIPTION "An enumerated value which specifies the IP address type of the source. It must be used along with the cipslaIcmpEchoTmplSrcAddr object." DEFVAL { ipv4 } ::= { cipslaIcmpEchoTmplEntry 3 } cipslaIcmpEchoTmplSrcAddr OBJECT-TYPE SYNTAX InetAddress MAX-ACCESS read-create STATUS current DESCRIPTION "A string which specifies the IP address of the source." ::= { cipslaIcmpEchoTmplEntry 4 } cipslaIcmpEchoTmplTimeOut OBJECT-TYPE SYNTAX Unsigned32 (0..604800000 ) UNITS "milliseconds" MAX-ACCESS read-create STATUS current DESCRIPTION "Specifies the duration to wait for a IP SLA operation completion. For connection oriented protocols, this may cause the connection to be closed by the operation. Once closed, it will be assumed that the connection reestablishment will be performed. To prevent unwanted closure of connections, be sure to set this value to a realistic connection timeout." DEFVAL { 5000 } ::= { cipslaIcmpEchoTmplEntry 5 } cipslaIcmpEchoTmplVerifyData OBJECT-TYPE SYNTAX TruthValue MAX-ACCESS read-create STATUS current DESCRIPTION "When set to true, the resulting data in each IP SLA operation is compared with the expected data. This includes checking header information (if possible) and exact packet size." DEFVAL { false } ::= { cipslaIcmpEchoTmplEntry 6 } cipslaIcmpEchoTmplReqDataSize OBJECT-TYPE SYNTAX Unsigned32 (0..16384 ) UNITS "octets" MAX-ACCESS read-create STATUS current DESCRIPTION "This object represents the number of octets to be placed into the ARR Data portion of the request message, when using SNA protocols. For non-ARR protocols' IP SLA request/responses, this value represents the native payload size. REMEMBER: The ARR Header overhead is not included in this value." DEFVAL { 28 } ::= { cipslaIcmpEchoTmplEntry 7 } cipslaIcmpEchoTmplTOS OBJECT-TYPE SYNTAX Unsigned32 (0..255 ) MAX-ACCESS read-create STATUS current DESCRIPTION "This object represents the type of service octet in an IP header." REFERENCE "Refer to the following documents for TOS definition. RFC791/1349 for IPv4, IPv6, draft-ietf-diffserv-header-02.txt" DEFVAL { 0 } ::= { cipslaIcmpEchoTmplEntry 8 } cipslaIcmpEchoTmplVrfName OBJECT-TYPE SYNTAX SnmpAdminString (SIZE (0..32)) MAX-ACCESS read-create STATUS current DESCRIPTION "This field is used to specify the VRF name with which the IP SLA operation will be used. For regular IP SLA operation this field should not be configured. The agent will use this field to identify the VRF routing table for this operation." DEFVAL { "" } ::= { cipslaIcmpEchoTmplEntry 9 } cipslaIcmpEchoTmplThreshold OBJECT-TYPE SYNTAX Unsigned32 (0..2147483647 ) UNITS "milliseconds" MAX-ACCESS read-create STATUS current DESCRIPTION "This object defines an administrative threshold limit. If the IP SLA operation time exceeds this limit and if the condition specified in cipslaIcmpEchoTmplHistFilter is satisfied, one threshold crossing occurrence will be counted." DEFVAL { 5000 } ::= { cipslaIcmpEchoTmplEntry 10 } cipslaIcmpEchoTmplHistLives OBJECT-TYPE SYNTAX Unsigned32 (0..2 ) MAX-ACCESS read-create STATUS current DESCRIPTION "The maximum number of history lives to record. A life is defined by the countdown (or transition) to zero by the cipslaAutoGroupScheduleLife object. A new life is created when the same conceptual control row is restarted via the transition of the cipslaAutoGroupScheduleLife object and its subsequent countdown. The value of zero will shut off all data collection." DEFVAL { 0 } ::= { cipslaIcmpEchoTmplEntry 11 } cipslaIcmpEchoTmplHistBuckets OBJECT-TYPE SYNTAX Unsigned32 (1..60 ) MAX-ACCESS read-create STATUS current DESCRIPTION "The maximum number of history buckets to record. This value is set to the number of operations to keep per lifetime. After cipslaIcmpEchoTmplHistBuckets are filled, the oldest entries are deleted and the most recent cipslaIcmpEchoTmplHistBuckets buckets are retained." DEFVAL { 15 } ::= { cipslaIcmpEchoTmplEntry 12 } cipslaIcmpEchoTmplHistFilter OBJECT-TYPE SYNTAX INTEGER { none(1), all(2), overThreshold(3), failures(4) } MAX-ACCESS read-create STATUS current DESCRIPTION "Defines a filter for adding RTT results to the history buffer: none(1) - no history is recorded all(2) - the results of all completion times and failed completions are recorded overThreshold(3) - the results of completion times over cipslaIcmpEchoTmplThreshold are recorded. failures(4) - the results of failed operations (only) are recorded." DEFVAL { none } ::= { cipslaIcmpEchoTmplEntry 13 } cipslaIcmpEchoTmplStatsHours OBJECT-TYPE SYNTAX Unsigned32 (0..25 ) UNITS "hours" MAX-ACCESS read-create STATUS current DESCRIPTION "The maximum number of hours for which statistics are maintained. Specifically this is the number of hourly groups to keep before rolling over. The value of one is not advisable because the hourly group will close and immediately be deleted before the network management station will have the opportunity to retrieve the statistics. The value of zero will shut off data collection." DEFVAL { 2 } ::= { cipslaIcmpEchoTmplEntry 14 } cipslaIcmpEchoTmplDistBuckets OBJECT-TYPE SYNTAX Unsigned32 (1..20 ) MAX-ACCESS read-create STATUS current DESCRIPTION "The maximum number of statistical distribution buckets to accumulate. Since this index does not rollover, only the first cipslaIcmpEchoTmplStatsNumDistBuckets will be kept. The last cipslaIcmpEchoTmplStatsNumDistBucket will contain all entries from its distribution interval start point to infinity." DEFVAL { 1 } ::= { cipslaIcmpEchoTmplEntry 15 } cipslaIcmpEchoTmplDistInterval OBJECT-TYPE SYNTAX Unsigned32 (1..100 ) UNITS "milliseconds" MAX-ACCESS read-create STATUS current DESCRIPTION "The statistical distribution buckets interval. Distribution Bucket Example: cipslaIcmpEchoTmplDistBuckets = 5 buckets cipslaIcmpEchoTmplDistInterval = 10 milliseconds | Bucket 1 | Bucket 2 | Bucket 3 | Bucket 4 | Bucket 5 | | 0-9 ms | 10-19 ms | 20-29 ms | 30-39 ms | 40-Inf ms | Odd Example: cipslaIcmpEchoTmplDistBuckets = 1 buckets cipslaIcmpEchoTmplDistInterval = 10 milliseconds | Bucket 1 | | 0-Inf ms | Thus, this odd example shows that the value of cipslaIcmpEchoTmplDistInterval does not apply when cipslaIcmpEchoTmplDistBuckets is one." DEFVAL { 20 } ::= { cipslaIcmpEchoTmplEntry 16 } cipslaIcmpEchoTmplStorageType OBJECT-TYPE SYNTAX StorageType MAX-ACCESS read-create STATUS current DESCRIPTION "The storage type of this conceptual row." DEFVAL { nonVolatile } ::= { cipslaIcmpEchoTmplEntry 17 } cipslaIcmpEchoTmplRowStatus OBJECT-TYPE SYNTAX RowStatus MAX-ACCESS read-create STATUS current DESCRIPTION "The status of the conceptual ICMP echo template control row. When the status is active, all the read-create objects in that row can be modified." ::= { cipslaIcmpEchoTmplEntry 18 } cipslaUdpEchoTmplTable OBJECT-TYPE SYNTAX SEQUENCE OF CipslaUdpEchoTmplEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "A table that contains UDP echo template specific definitions." ::= { ciscoIpSlaEchoMIBObjects 2 } cipslaUdpEchoTmplEntry OBJECT-TYPE SYNTAX CipslaUdpEchoTmplEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "A row entry representing an IPSLA UDP echo template." INDEX { cipslaUdpEchoTmplName } ::= { cipslaUdpEchoTmplTable 1 } CipslaUdpEchoTmplEntry ::= SEQUENCE { cipslaUdpEchoTmplName SnmpAdminString, cipslaUdpEchoTmplDescription SnmpAdminString, cipslaUdpEchoTmplControlEnable TruthValue, cipslaUdpEchoTmplSrcAddrType InetAddressType, cipslaUdpEchoTmplSrcAddr InetAddress, cipslaUdpEchoTmplSrcPort InetPortNumber, cipslaUdpEchoTmplTimeOut Unsigned32, cipslaUdpEchoTmplVerifyData TruthValue, cipslaUdpEchoTmplReqDataSize Unsigned32, cipslaUdpEchoTmplTOS Unsigned32, cipslaUdpEchoTmplVrfName SnmpAdminString, cipslaUdpEchoTmplThreshold Unsigned32, cipslaUdpEchoTmplHistLives Unsigned32, cipslaUdpEchoTmplHistBuckets Unsigned32, cipslaUdpEchoTmplHistFilter INTEGER , cipslaUdpEchoTmplStatsHours Unsigned32, cipslaUdpEchoTmplDistBuckets Unsigned32, cipslaUdpEchoTmplDistInterval Unsigned32, cipslaUdpEchoTmplStorageType StorageType, cipslaUdpEchoTmplRowStatus RowStatus } cipslaUdpEchoTmplName OBJECT-TYPE SYNTAX SnmpAdminString (SIZE (1..64)) MAX-ACCESS not-accessible STATUS current DESCRIPTION "A string which specifies the UDP echo template name." ::= { cipslaUdpEchoTmplEntry 1 } cipslaUdpEchoTmplDescription OBJECT-TYPE SYNTAX SnmpAdminString (SIZE (0..128)) MAX-ACCESS read-create STATUS current DESCRIPTION "A string which provides description to the UDP echo template." DEFVAL { "" } ::= { cipslaUdpEchoTmplEntry 2 } cipslaUdpEchoTmplControlEnable OBJECT-TYPE SYNTAX TruthValue MAX-ACCESS read-create STATUS current DESCRIPTION "If this object is enabled, then the IP SLA application will send control messages to a responder, residing on the target router to respond to the data request packets being sent by the source router." DEFVAL { true } ::= { cipslaUdpEchoTmplEntry 3 } cipslaUdpEchoTmplSrcAddrType OBJECT-TYPE SYNTAX InetAddressType MAX-ACCESS read-create STATUS current DESCRIPTION "An enumerated value which specifies the IP address type of the source. It must be used along with the cipslaUdpEchoTmplSrcAddr object." DEFVAL { ipv4 } ::= { cipslaUdpEchoTmplEntry 4 } cipslaUdpEchoTmplSrcAddr OBJECT-TYPE SYNTAX InetAddress MAX-ACCESS read-create STATUS current DESCRIPTION "A string which specifies the IP address of the source." ::= { cipslaUdpEchoTmplEntry 5 } cipslaUdpEchoTmplSrcPort OBJECT-TYPE SYNTAX InetPortNumber MAX-ACCESS read-create STATUS current DESCRIPTION "This object represents the source's port number. If this object is not specified, the application will get a port allocated by the system." DEFVAL { 0 } ::= { cipslaUdpEchoTmplEntry 6 } cipslaUdpEchoTmplTimeOut OBJECT-TYPE SYNTAX Unsigned32 (0..604800000 ) UNITS "milliseconds" MAX-ACCESS read-create STATUS current DESCRIPTION "Specifies the duration to wait for an IP SLA operation completion. For connection oriented protocols, this may cause the connection to be closed by the operation. Once closed, it will be assumed that the connection reestablishment will be performed. To prevent unwanted closure of connections, be sure to set this value to a realistic connection timeout." DEFVAL { 5000 } ::= { cipslaUdpEchoTmplEntry 7 } cipslaUdpEchoTmplVerifyData OBJECT-TYPE SYNTAX TruthValue MAX-ACCESS read-create STATUS current DESCRIPTION "When set to true, the resulting data in each IP SLA operation is compared with the expected data. This includes checking header information (if possible) and exact packet size." DEFVAL { false } ::= { cipslaUdpEchoTmplEntry 8 } cipslaUdpEchoTmplReqDataSize OBJECT-TYPE SYNTAX Unsigned32 (4..1500 ) UNITS "octets" MAX-ACCESS read-create STATUS current DESCRIPTION "This object represents the number of octets to be placed into the ARR Data portion of the request message, when using SNA protocols. For non-ARR protocols' RTT request/responses, this value represents the native payload size. REMEMBER: The ARR Header overhead is not included in this value." DEFVAL { 16 } ::= { cipslaUdpEchoTmplEntry 9 } cipslaUdpEchoTmplTOS OBJECT-TYPE SYNTAX Unsigned32 (0..255 ) MAX-ACCESS read-create STATUS current DESCRIPTION "This object represents the type of service octet in an IP header." REFERENCE "Refer to the following documents for TOS definition. RFC791/1349 for IPv4, IPv6, draft-ietf-diffserv-header-02.txt" DEFVAL { 0 } ::= { cipslaUdpEchoTmplEntry 10 } cipslaUdpEchoTmplVrfName OBJECT-TYPE SYNTAX SnmpAdminString (SIZE (0..32)) MAX-ACCESS read-create STATUS current DESCRIPTION "This field is used to specify the VRF name with which the IP SLA operation will be used. For regular IP SLA operation this field should not be configured. The agent will use this field to identify the VRF routing Table for this operation." DEFVAL { "" } ::= { cipslaUdpEchoTmplEntry 11 } cipslaUdpEchoTmplThreshold OBJECT-TYPE SYNTAX Unsigned32 (0..2147483647 ) UNITS "milliseconds" MAX-ACCESS read-create STATUS current DESCRIPTION "This object defines an administrative threshold limit. If the IP SLA operation time exceeds this limit and if the condition specified in cipslaUdpEchoTmplHistFilter is satisfied, one threshold crossing occurrence will be counted." DEFVAL { 5000 } ::= { cipslaUdpEchoTmplEntry 12 } cipslaUdpEchoTmplHistLives OBJECT-TYPE SYNTAX Unsigned32 (0..2 ) MAX-ACCESS read-create STATUS current DESCRIPTION "The maximum number of history lives to record. A life is defined by the countdown (or transition) to zero by the cipslaAutoGroupScheduleLife object. A new life is created when the same conceptual control row is restarted via the transition of the cipslaAutoGroupScheduleLife object and its subsequent countdown. The value of zero will shut off all data collection." DEFVAL { 0 } ::= { cipslaUdpEchoTmplEntry 13 } cipslaUdpEchoTmplHistBuckets OBJECT-TYPE SYNTAX Unsigned32 (1..60 ) MAX-ACCESS read-create STATUS current DESCRIPTION "The maximum number of history buckets to record. This value should be set to the number of operations to keep per lifetime. After cipslaUdpEchoTmplHistBuckets are filled, the oldest entries are deleted and the most recent cipslaUdpEchoTmplHistBuckets buckets are retained." DEFVAL { 15 } ::= { cipslaUdpEchoTmplEntry 14 } cipslaUdpEchoTmplHistFilter OBJECT-TYPE SYNTAX INTEGER { none(1), all(2), overThreshold(3), failures(4) } MAX-ACCESS read-create STATUS current DESCRIPTION "Defines a filter for adding RTT results to the history buffer: none(1) - no history is recorded all(2) - the results of all completion times and failed completions are recorded overThreshold(3) - the results of completion times over cipslaUdpEchoTmplThreshold are recorded. failures(4) - the results of failed operations (only) are recorded." DEFVAL { none } ::= { cipslaUdpEchoTmplEntry 15 } cipslaUdpEchoTmplStatsHours OBJECT-TYPE SYNTAX Unsigned32 (0..25 ) UNITS "hours" MAX-ACCESS read-create STATUS current DESCRIPTION "The maximum number of hours for which statistics are maintained. Specifically this is the number of hourly groups to keep before rolling over. The value of one is not advisable because the hourly group will close and immediately be deleted before the network management station will have the opportunity to retrieve the statistics. The value of zero will shut off data collection." DEFVAL { 2 } ::= { cipslaUdpEchoTmplEntry 16 } cipslaUdpEchoTmplDistBuckets OBJECT-TYPE SYNTAX Unsigned32 (1..20 ) MAX-ACCESS read-create STATUS current DESCRIPTION "The maximum number of statistical distribution buckets to accumulate. Since this index does not rollover, only the first cipslaUdpEchoTmplStatsNumDistBuckets will be kept. The last cipslaUdpEchoTmplStatsNumDistBuckets will contain all entries from its distribution interval start point to infinity." DEFVAL { 1 } ::= { cipslaUdpEchoTmplEntry 17 } cipslaUdpEchoTmplDistInterval OBJECT-TYPE SYNTAX Unsigned32 (1..100 ) UNITS "milliseconds" MAX-ACCESS read-create STATUS current DESCRIPTION "The statistical distribution buckets interval. Distribution Bucket Example: cipslaUdpEchoTmplDistBuckets = 5 buckets cipslaUdpEchoTmplDistInterval = 10 milliseconds | Bucket 1 | Bucket 2 | Bucket 3 | Bucket 4 | Bucket 5 | | 0-9 ms | 10-19 ms | 20-29 ms | 30-39 ms | 40-Inf ms | Odd Example: cipslaUdpEchoTmplDistBuckets = 1 buckets cipslaUdpEchoTmplDistInterval = 10 milliseconds | Bucket 1 | | 0-Inf ms | Thus, this odd example shows that the value of cipslaUdpEchoTmplDistInterval does not apply when cipslaUdpEchoTmplDistBuckets is one." DEFVAL { 20 } ::= { cipslaUdpEchoTmplEntry 18 } cipslaUdpEchoTmplStorageType OBJECT-TYPE SYNTAX StorageType MAX-ACCESS read-create STATUS current DESCRIPTION "The storage type of this conceptual row." DEFVAL { nonVolatile } ::= { cipslaUdpEchoTmplEntry 19 } cipslaUdpEchoTmplRowStatus OBJECT-TYPE SYNTAX RowStatus MAX-ACCESS read-create STATUS current DESCRIPTION "The status of the conceptual UDP echo template control row. When the status is active, all the read-create objects in that row can be modified." ::= { cipslaUdpEchoTmplEntry 20 } cipslaTcpConnTmplTable OBJECT-TYPE SYNTAX SEQUENCE OF CipslaTcpConnTmplEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "A table that contains TCP connect template specific definitions." ::= { ciscoIpSlaEchoMIBObjects 3 } cipslaTcpConnTmplEntry OBJECT-TYPE SYNTAX CipslaTcpConnTmplEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "A row entry representing an IPSLA TCP connect template." INDEX { cipslaTcpConnTmplName } ::= { cipslaTcpConnTmplTable 1 } CipslaTcpConnTmplEntry ::= SEQUENCE { cipslaTcpConnTmplName SnmpAdminString, cipslaTcpConnTmplDescription SnmpAdminString, cipslaTcpConnTmplControlEnable TruthValue, cipslaTcpConnTmplSrcAddrType InetAddressType, cipslaTcpConnTmplSrcAddr InetAddress, cipslaTcpConnTmplSrcPort InetPortNumber, cipslaTcpConnTmplTimeOut Unsigned32, cipslaTcpConnTmplVerifyData TruthValue, cipslaTcpConnTmplTOS Unsigned32, cipslaTcpConnTmplThreshold Unsigned32, cipslaTcpConnTmplHistLives Unsigned32, cipslaTcpConnTmplHistBuckets Unsigned32, cipslaTcpConnTmplHistFilter INTEGER , cipslaTcpConnTmplStatsHours Unsigned32, cipslaTcpConnTmplDistBuckets Unsigned32, cipslaTcpConnTmplDistInterval Unsigned32, cipslaTcpConnTmplStorageType StorageType, cipslaTcpConnTmplRowStatus RowStatus } cipslaTcpConnTmplName OBJECT-TYPE SYNTAX SnmpAdminString (SIZE (1..64)) MAX-ACCESS not-accessible STATUS current DESCRIPTION "A string which specifies the TCP connect template name." ::= { cipslaTcpConnTmplEntry 1 } cipslaTcpConnTmplDescription OBJECT-TYPE SYNTAX SnmpAdminString (SIZE (0..128)) MAX-ACCESS read-create STATUS current DESCRIPTION "A string which provides description for the TCP connect template." DEFVAL { "" } ::= { cipslaTcpConnTmplEntry 2 } cipslaTcpConnTmplControlEnable OBJECT-TYPE SYNTAX TruthValue MAX-ACCESS read-create STATUS current DESCRIPTION "If this object is enabled, then the IP SLA application will send control messages to a responder, residing on the target router to respond to the data request packets being sent by the source router." DEFVAL { true } ::= { cipslaTcpConnTmplEntry 3 } cipslaTcpConnTmplSrcAddrType OBJECT-TYPE SYNTAX InetAddressType MAX-ACCESS read-create STATUS current DESCRIPTION "An enumerated value which specifies the IP address type of the source. It must be used along with the cipslaTcpConnTmplSrcAddr object." DEFVAL { ipv4 } ::= { cipslaTcpConnTmplEntry 4 } cipslaTcpConnTmplSrcAddr OBJECT-TYPE SYNTAX InetAddress MAX-ACCESS read-create STATUS current DESCRIPTION "A string which specifies the IP address of the source." ::= { cipslaTcpConnTmplEntry 5 } cipslaTcpConnTmplSrcPort OBJECT-TYPE SYNTAX InetPortNumber MAX-ACCESS read-create STATUS current DESCRIPTION "This object represents the source's port number. If this object is not specified, the application will get a port allocated by the system." DEFVAL { 0 } ::= { cipslaTcpConnTmplEntry 6 } cipslaTcpConnTmplTimeOut OBJECT-TYPE SYNTAX Unsigned32 (0..604800000 ) UNITS "milliseconds" MAX-ACCESS read-create STATUS current DESCRIPTION "Specifies the duration to wait for an IP SLA operation completion. For connection oriented protocols, this may cause the connection to be closed by the operation. Once closed, it will be assumed that the connection reestablishment will be performed. To prevent unwanted closure of connections, be sure to set this value to a realistic connection timeout." DEFVAL { 5000 } ::= { cipslaTcpConnTmplEntry 7 } cipslaTcpConnTmplVerifyData OBJECT-TYPE SYNTAX TruthValue MAX-ACCESS read-create STATUS current DESCRIPTION "When set to true, the resulting data in each IP SLA operation is compared with the expected data. This includes checking header information (if possible) and exact packet size." DEFVAL { false } ::= { cipslaTcpConnTmplEntry 8 } cipslaTcpConnTmplTOS OBJECT-TYPE SYNTAX Unsigned32 (0..255 ) MAX-ACCESS read-create STATUS current DESCRIPTION "This object represents the type of service octet in an IP header." REFERENCE "Refer to the following documents for TOS definition. RFC791/1349 for IPv4, IPv6, draft-ietf-diffserv-header-02.txt" DEFVAL { 0 } ::= { cipslaTcpConnTmplEntry 9 } cipslaTcpConnTmplThreshold OBJECT-TYPE SYNTAX Unsigned32 (0..2147483647 ) UNITS "milliseconds" MAX-ACCESS read-create STATUS current DESCRIPTION "This object defines an administrative threshold limit. If the IP SLA operation time exceeds this limit and if the condition specified in cipslaTcpConnTmplHistFilter is satisfied, one threshold crossing occurrence will be counted." DEFVAL { 5000 } ::= { cipslaTcpConnTmplEntry 10 } cipslaTcpConnTmplHistLives OBJECT-TYPE SYNTAX Unsigned32 (0..2 ) MAX-ACCESS read-create STATUS current DESCRIPTION "The maximum number of history lives to record. A life is defined by the countdown (or transition) to zero by the cipslaAutoGroupScheduleLife object. A new life is created when the same conceptual control row is restarted via the transition of the cipslaAutoGroupScheduleLife object and its subsequent countdown. The value of zero will shut off all data collection." DEFVAL { 0 } ::= { cipslaTcpConnTmplEntry 11 } cipslaTcpConnTmplHistBuckets OBJECT-TYPE SYNTAX Unsigned32 (1..60 ) MAX-ACCESS read-create STATUS current DESCRIPTION "The maximum number of history buckets to record. This value should be set to the number of operations to keep per lifetime. After cipslaTcpConnTmplHistBuckets are filled, the oldest entries are deleted and the most recent cipslaTcpConnTmplHistBuckets buckets are retained." DEFVAL { 15 } ::= { cipslaTcpConnTmplEntry 12 } cipslaTcpConnTmplHistFilter OBJECT-TYPE SYNTAX INTEGER { none(1), all(2), overThreshold(3), failures(4) } MAX-ACCESS read-create STATUS current DESCRIPTION "Defines a filter for adding RTT results to the history buffer: none(1) - no history is recorded all(2) - the results of all completion times and failed completions are recorded overThreshold(3) - the results of completion times over cipslaTcpConnTmplThreshold are recorded. failures(4) - the results of failed operations (only) are recorded." DEFVAL { none } ::= { cipslaTcpConnTmplEntry 13 } cipslaTcpConnTmplStatsHours OBJECT-TYPE SYNTAX Unsigned32 (0..25 ) UNITS "hours" MAX-ACCESS read-create STATUS current DESCRIPTION "The maximum number of hours for which statistics are maintained. Specifically this is the number of hourly groups to keep before rolling over. The value of one is not advisable because the hourly group will close and immediately be deleted before the network management station will have the opportunity to retrieve the statistics. The value of zero will shut off data collection." DEFVAL { 2 } ::= { cipslaTcpConnTmplEntry 14 } cipslaTcpConnTmplDistBuckets OBJECT-TYPE SYNTAX Unsigned32 (1..20 ) MAX-ACCESS read-create STATUS current DESCRIPTION "The maximum number of statistical distribution buckets to accumulate. Since this index does not rollover, only the first cipslaTcpConnTmplDistBuckets will be kept. The last cipslaTcpConnTmplDistBuckets will contain all entries from its distribution interval start point to infinity." DEFVAL { 1 } ::= { cipslaTcpConnTmplEntry 15 } cipslaTcpConnTmplDistInterval OBJECT-TYPE SYNTAX Unsigned32 (1..100 ) UNITS "milliseconds" MAX-ACCESS read-create STATUS current DESCRIPTION "The statistical distribution buckets interval. Distribution Bucket Example: cipslaTcpConnTmplDistBuckets = 5 buckets cipslaTcpConnTmplDistInterval = 10 milliseconds | Bucket 1 | Bucket 2 | Bucket 3 | Bucket 4 | Bucket 5 | | 0-9 ms | 10-19 ms | 20-29 ms | 30-39 ms | 40-Inf ms | Odd Example: cipslaTcpConnTmplDistBuckets = 1 buckets cipslaTcpConnTmplDistInterval = 10 milliseconds | Bucket 1 | | 0-Inf ms | Thus, this odd example shows that the value of cipslaTcpConnTmplDistInterval does not apply when cipslaTcpConnTmplDistBuckets is one." DEFVAL { 20 } ::= { cipslaTcpConnTmplEntry 16 } cipslaTcpConnTmplStorageType OBJECT-TYPE SYNTAX StorageType MAX-ACCESS read-create STATUS current DESCRIPTION "The storage type of this conceptual row." DEFVAL { nonVolatile } ::= { cipslaTcpConnTmplEntry 17 } cipslaTcpConnTmplRowStatus OBJECT-TYPE SYNTAX RowStatus MAX-ACCESS read-create STATUS current DESCRIPTION "The status of the conceptual tcp connect control row. When the status is active, all the read-create objects in that row can be modified." ::= { cipslaTcpConnTmplEntry 18 } -- Conformance Information ciscoIpSlaEchoMIBConform OBJECT IDENTIFIER ::= { ciscoIpSlaEchoMIB 2 } ciscoIpSlaEchoMIBCompliances OBJECT IDENTIFIER ::= { ciscoIpSlaEchoMIBConform 1 } ciscoIpSlaEchoMIBGroups OBJECT IDENTIFIER ::= { ciscoIpSlaEchoMIBConform 2 } ciscoIpSlaEchoMIBCompliance MODULE-COMPLIANCE STATUS current DESCRIPTION "The compliance statement for IP SLA (1) ICMP echo Template (2) UDP echo Template (3) TCP connect Template" MODULE -- this module MANDATORY-GROUPS { ciscoIpSlaIcmpEchoTmplGroup, ciscoIpSlaUdpEchoTmplGroup, ciscoIpSlaTcpConnTmplGroup } ::= { ciscoIpSlaEchoMIBCompliances 1 } ciscoIpSlaIcmpEchoTmplGroup OBJECT-GROUP OBJECTS { cipslaIcmpEchoTmplDescription, cipslaIcmpEchoTmplSrcAddrType, cipslaIcmpEchoTmplSrcAddr, cipslaIcmpEchoTmplTimeOut, cipslaIcmpEchoTmplVerifyData, cipslaIcmpEchoTmplReqDataSize, cipslaIcmpEchoTmplTOS, cipslaIcmpEchoTmplVrfName, cipslaIcmpEchoTmplThreshold, cipslaIcmpEchoTmplHistLives, cipslaIcmpEchoTmplHistBuckets, cipslaIcmpEchoTmplHistFilter, cipslaIcmpEchoTmplStatsHours, cipslaIcmpEchoTmplDistBuckets, cipslaIcmpEchoTmplDistInterval, cipslaIcmpEchoTmplStorageType, cipslaIcmpEchoTmplRowStatus } STATUS current DESCRIPTION "A collection of objects related to ICMP echo Template." ::= { ciscoIpSlaEchoMIBGroups 1 } ciscoIpSlaUdpEchoTmplGroup OBJECT-GROUP OBJECTS { cipslaUdpEchoTmplDescription, cipslaUdpEchoTmplControlEnable, cipslaUdpEchoTmplSrcAddrType, cipslaUdpEchoTmplSrcAddr, cipslaUdpEchoTmplSrcPort, cipslaUdpEchoTmplTimeOut, cipslaUdpEchoTmplVerifyData, cipslaUdpEchoTmplReqDataSize, cipslaUdpEchoTmplTOS, cipslaUdpEchoTmplVrfName, cipslaUdpEchoTmplThreshold, cipslaUdpEchoTmplHistLives, cipslaUdpEchoTmplHistBuckets, cipslaUdpEchoTmplHistFilter, cipslaUdpEchoTmplStatsHours, cipslaUdpEchoTmplDistBuckets, cipslaUdpEchoTmplDistInterval, cipslaUdpEchoTmplStorageType, cipslaUdpEchoTmplRowStatus } STATUS current DESCRIPTION "A collection of objects related to UDP echo Template." ::= { ciscoIpSlaEchoMIBGroups 2 } ciscoIpSlaTcpConnTmplGroup OBJECT-GROUP OBJECTS { cipslaTcpConnTmplDescription, cipslaTcpConnTmplControlEnable, cipslaTcpConnTmplSrcAddrType, cipslaTcpConnTmplSrcAddr, cipslaTcpConnTmplSrcPort, cipslaTcpConnTmplTimeOut, cipslaTcpConnTmplVerifyData, cipslaTcpConnTmplTOS, cipslaTcpConnTmplThreshold, cipslaTcpConnTmplHistLives, cipslaTcpConnTmplHistBuckets, cipslaTcpConnTmplHistFilter, cipslaTcpConnTmplStatsHours, cipslaTcpConnTmplDistBuckets, cipslaTcpConnTmplDistInterval, cipslaTcpConnTmplStorageType, cipslaTcpConnTmplRowStatus } STATUS current DESCRIPTION "A collection of objects related to TCP connect Template." ::= { ciscoIpSlaEchoMIBGroups 3 } END