-- ***************************************************************** -- CISCO-IF-THRESHOLD-MIB.my: Cisco Interface Threshold MIB -- -- May 2001, E. Mickey Spiegel, Sonal Maheshwari -- -- Copyright (c) 2001 by Cisco Systems, Inc. -- All rights reserved. -- ***************************************************************** CISCO-IF-THRESHOLD-MIB DEFINITIONS ::= BEGIN IMPORTS MODULE-IDENTITY, OBJECT-TYPE, NOTIFICATION-TYPE, Integer32, Unsigned32 FROM SNMPv2-SMI TEXTUAL-CONVENTION, RowStatus, TimeStamp, TruthValue FROM SNMPv2-TC MODULE-COMPLIANCE, OBJECT-GROUP, NOTIFICATION-GROUP FROM SNMPv2-CONF SnmpAdminString FROM SNMP-FRAMEWORK-MIB ciscoMgmt FROM CISCO-SMI InterfaceIndex, ifIndex FROM IF-MIB; ciscoIfThresholdMIB MODULE-IDENTITY LAST-UPDATED "200109140000Z" ORGANIZATION "Cisco Systems, Inc." CONTACT-INFO "Cisco Systems Customer Service Postal: 170 W Tasman Drive San Jose, CA 95134 USA Tel: +1 800 553-NETS E-mail: cs-dwdm@cisco.com" DESCRIPTION "This MIB module defines the managed objects that support monitoring of thresholds on interfaces. Configuration and monitoring of the thresholds is done through threshold templates that can be assigned to any subset of interfaces on the network element. More than one threshold template can be assigned to a given interface. This MIB module should be used when it is desired to apply a common set of thresholds to a subset of the available interfaces. If a threshold is to be applied to only one interface, then the EVENT-MIB or the RMON-MIB may be used as simpler alternatives. If a threshold is to be applied to all available interfaces, then the EVENT-MIB may be used as a simpler alternative." REVISION "200109140000Z" DESCRIPTION "Second version of this MIB module." REVISION "200106140000Z" DESCRIPTION "Initial version of this MIB module." ::= { ciscoMgmt 218 } -- Textual Conventions CifthTemplateIndex ::= TEXTUAL-CONVENTION STATUS current DESCRIPTION "An arbitrary integer that uniquely identifies a threshold template. The value for each threshold template must remain constant at least from one re-initialization of the agent's network management system to the next re-initialization. The value may change when the agent's network management system is rebooted or re-initialized." SYNTAX Unsigned32 (1..1000) CifthTemplateIndexOrZero ::= TEXTUAL-CONVENTION STATUS current DESCRIPTION "A value of either '0' or a valid template index. The distinguished value '0' indicates no template or no unassigned template index values are available." SYNTAX Unsigned32 (0..1000) CifthThresholdIndex ::= TEXTUAL-CONVENTION STATUS current DESCRIPTION "An arbitrary integer that uniquely identifies a threshold within a threshold template. The value for each threshold must remain constant when the agent's network management system is rebooted or re-initialized." SYNTAX Unsigned32 (0..63) CifthThresholdList ::= TEXTUAL-CONVENTION STATUS current DESCRIPTION "A list of thresholds defined in a given template, in which each bit represents one threshold. The bits in the first octet represent thresholds identified by cifthThresholdIndex values 0 through 7, inclusive. The bits in the second octet represent thresholds identified by integer values 8 through 15, inclusive, and so forth. The least significant bit of an octet represents the threshold identified by the lowest integer value, and the most significant bit represents the threshold identified by the highest integer value. The figure shown below illustrates the format of a threshold list. Octet 1 Octet 8 7 6 5 4 3 2 1 0 7 6 5 4 3 2 1 0 +-+-+-+-+-+-+-+-+ +-+-+-+-+-+-+-+-+ | |...| | +-+-+-+-+-+-+-+-+ +-+-+-+-+-+-+-+-+ | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | +- Threshold 56 | | | | | | | | | | | | | | +--- Threshold 57 | | | | | | | | | | | | | +----- Threshold 58 | | | | | | | | | | | | +------- Threshold 59 | | | | | | | | | | | +--------- Threshold 60 | | | | | | | | | | +----------- Threshold 61 | | | | | | | | | +------------- Threshold 62 | | | | | | | | +--------------- Threshold 63 | | | | | | | | : | | | | | | | | : | | | | | | | +--------------------- Threshold 0 | | | | | | +----------------------- Threshold 1 | | | | | +------------------------- Threshold 2 | | | | +--------------------------- Threshold 3 | | | +----------------------------- Threshold 4 | | +------------------------------- Threshold 5 | +--------------------------------- Threshold 6 +----------------------------------- Threshold 7 A bit value of '1' indicates that the threshold is being exceeded in current operation (i.e., the threshold is fired). A bit value of '0' indicates that the threshold is not being exceeded in current operation (i.e., the threshold is cleared). A threshold list of length N, where N < 8, represents a threshold list for which thresholds N*8 through 63 have the value of '0'. A special case is a threshold list having a length of '0', which represents a threshold list of all zeros." SYNTAX OCTET STRING (SIZE(0..8)) CifthThresholdSeverity ::= TEXTUAL-CONVENTION STATUS current DESCRIPTION "The severity of the condition when the threshold is fired. A smaller enumerated integer value indicates that the threshold exceeded condition is more severe. The value 'fail' indicates a hard failure condition where no data can be received, or where the data received has a large number of errors which makes it impossible to recover most of the data. The value 'degrade' indicates a soft failure condition in which data received on this interface is affected, but a significant portion of the data can be recovered. The value 'info' is used to raise attention to a condition that could possibly be an impending problem or to notify the customer of an event that improves operation." SYNTAX INTEGER { fail(1), degrade(2), info(3), other(4) } CifthThresholdSeverityOrZero ::= TEXTUAL-CONVENTION STATUS current DESCRIPTION "A value of either '0' or a valid threshold severity." SYNTAX INTEGER (0..4) -- MIB Object Definitions cIfThresholdMIBObjects OBJECT IDENTIFIER ::= { ciscoIfThresholdMIB 1 } cifthTemplateGroup OBJECT IDENTIFIER ::= { cIfThresholdMIBObjects 1 } cifthTemplateIfAssignGroup OBJECT IDENTIFIER ::= { cIfThresholdMIBObjects 2 } cifthIfThresholdFiredGroup OBJECT IDENTIFIER ::= { cIfThresholdMIBObjects 3 } -- Template Table cifthTemplateIndexNext OBJECT-TYPE SYNTAX CifthTemplateIndexOrZero MAX-ACCESS read-only STATUS current DESCRIPTION "This object contains an appropriate value to be used for cifthTemplateIndex when creating entries in the cifthTemplateTable. The distinguished value 0 indicates that no unassigned entries are available. To obtain a suggested cifthTemplateIndex value for a new entry, the manager issues a management protocol retrieval operation to obtain the current value of this object. The manager may ignore this object and use alternative mechanisms for choosing an unused value of cifthTemplateIndex for a new entry. The agent will modify the value to the next unassigned index, when a new entry is created in cifthTemplateTable with the current value of this object. After deletion of an entry in cifthTemplateTable the agent will determine through its local policy when its index value will be made available for reuse." ::= { cifthTemplateGroup 1 } cifthTemplateLastChange OBJECT-TYPE SYNTAX TimeStamp MAX-ACCESS read-only STATUS current DESCRIPTION "This object specifies the value of sysUpTime at the last time there was either a change to any object in any entry in cifthTemplateTable, or an entry was created or destroyed in cifthTemplateTable. If no change to cifthTemplateTable has occurred since the last re-initialization of the local network management subsystem, then this object contains a zero value." ::= { cifthTemplateGroup 2 } cifthTemplateTable OBJECT-TYPE SYNTAX SEQUENCE OF CifthTemplateEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "This table is used to create threshold templates. Each template includes one or more thresholds (defined in the cifthThresholdTable), and can be assigned to multiple interfaces. An interface may be associated with more than one template. The assignment of templates to interfaces is done in the cifthTemplateIfAssignTable." ::= { cifthTemplateGroup 3 } cifthTemplateEntry OBJECT-TYPE SYNTAX CifthTemplateEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "An entry describing the general properties of a threshold template. The template is created using the cifthTemplateRowStatus object. Prior to creating an entry in the table, the manager should obtain a unique value of cifthTemplateIndex by reading the cifthTemplateIndexNext object. The values of cifthTemplateName and cifthTemplateNotifyHoldDownType must be provided before activating the entry. After creating an entry, thresholds can be defined for the template by creating entries with the same value of cifthTemplateIndex in the cifthThresholdTable. The template can then be assigned to one or more interfaces using the cifthTemplateIfAssignTable. Once an entry has been activated, the value of cifthTemplateName cannot be modified. In order to use a new value of cifthTemplateName, a new template must be defined. The values of cifthTemplateNotifyHoldDownType and cifthTemplateNotifyHoldDownTime may be modified when the entry is active. See the description clause of cifthTemplateNotifyHoldDownType for further caveats on modification of that object." INDEX { cifthTemplateIndex } ::= { cifthTemplateTable 1 } CifthTemplateEntry ::= SEQUENCE { cifthTemplateIndex CifthTemplateIndex, cifthTemplateName SnmpAdminString, cifthTemplateNotifyHoldDownType INTEGER, cifthTemplateNotifyHoldDownTime Unsigned32, cifthTemplateRowStatus RowStatus } cifthTemplateIndex OBJECT-TYPE SYNTAX CifthTemplateIndex MAX-ACCESS not-accessible STATUS current DESCRIPTION "An arbitrary integer that uniquely identifies a threshold template. The value for each threshold template must remain constant at least from one re-initialization of the agent's network management system to the next re-initialization. The value may change when the agent's network management system is rebooted or re-initialized." ::= { cifthTemplateEntry 1 } cifthTemplateName OBJECT-TYPE SYNTAX SnmpAdminString (SIZE(1..32)) MAX-ACCESS read-create STATUS current DESCRIPTION "This object specifies a unique name associated with the threshold template by the management client, and provides a non-volatile 'handle' for the template. The name must not include whitespace characters. After this value has been written to the startup configuration, the agent must retain the value until a management client deletes it. The level of retention must span reboots and re-initializations of the agent, including those that result in different assignments to the value of cifthTemplateIndex associated with this template. Once an entry has been activated, this value cannot be modified. In order to use a new value of cifthTemplateName, a new template must be defined." ::= { cifthTemplateEntry 2 } cifthTemplateNotifyHoldDownType OBJECT-TYPE SYNTAX INTEGER { other(1), holdDownTimer(2), fireAndClearThresholds(3) -- hysteresis } MAX-ACCESS read-create STATUS current DESCRIPTION "This object specifies the method used to prevent an excess of notifications from being generated when operation fluctuates around a threshold level. The value 'holdDownTimer' indicates that notifications for a given threshold and interface are suppressed for a short amount of time after each notification. The time value is specified in cifthTemplateNotifyHoldDownTime, which is instantiated only when this object is set to 'holdDownTimer'. After a notification is received for a given threshold and interface, the next notification for that threshold and interface will be generated after at least cifthTemplateNotifyHoldDownTime amount of time has passed, only when the threshold is next fired or cleared. The value 'fireAndClearThresholds' indicates that hysteresis is used. The management client configures two values for each threshold: one for asserting that the threshold has been exceeded (see cifthThresholdFiredValue), and a second value for asserting that the threshold is no longer being exceeded (see cifthThresholdClearedValue, which is instantiated only when this object is set to 'fireAndClearThresholds'). When this entry in cifthTemplateTable is active, this object may only be modified if there are no active entries in cifthThresholdTable with the same value of cifthTemplateIndex." ::= { cifthTemplateEntry 3 } cifthTemplateNotifyHoldDownTime OBJECT-TYPE SYNTAX Unsigned32 (1..3600) UNITS "seconds" MAX-ACCESS read-create STATUS current DESCRIPTION "The minimum amount of time between successive cifthIfThresholdFired or cifthIfThresholdCleared notifications for a given interface and template. This object is instantiated only when cifthTemplateNotifyHoldDownType is set to 'holdDownTimer'." DEFVAL { 5 } ::= { cifthTemplateEntry 4 } cifthTemplateRowStatus OBJECT-TYPE SYNTAX RowStatus MAX-ACCESS read-create STATUS current DESCRIPTION "This object is used to create and delete threshold templates. The values of cifthTemplateName and cifthTemplateNotifyHoldDownType must be provided before activating the entry. An entry can only be deleted when there are no active entries in the cifthTemplateIfAssignTable with the same value of cifthTemplateIndex. When an entry is deleted, all associated entries in the cifthThresholdTable are also deleted. After the entry has been activated, this object cannot be set to any value other than 'destroy'. The row status never changes to 'notInService' after reaching the value 'active'." ::= { cifthTemplateEntry 5 } -- Threshold Table cifthThresholdLastChange OBJECT-TYPE SYNTAX TimeStamp MAX-ACCESS read-only STATUS current DESCRIPTION "This object specifies the value of sysUpTime at the last time there was either a change to any object in any entry in cifthThresholdTable, or an entry was created or destroyed in cifthThresholdTable. If no change to cifthThresholdTable has occurred since the last re-initialization of the local network management subsystem, then this object contains a zero value." ::= { cifthTemplateGroup 4 } cifthThresholdTable OBJECT-TYPE SYNTAX SEQUENCE OF CifthThresholdEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "This table specifies the interface thresholds used in each template." ::= { cifthTemplateGroup 5 } cifthThresholdEntry OBJECT-TYPE SYNTAX CifthThresholdEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "An entry specifying an interface threshold used in a threshold template. The entry is created using the cifthThresholdRowStatus object. The values of cifthThresholdObject, cifthThresholdSeverity, cifthThresholdType, and cifthThresholdFiredValue must be provided before activating the entry. If the value of cifthTemplateNotifyHoldDownType in the cifthTemplateEntry with the same value of cifthTemplateIndex is 'fireAndClearThresholds', then the value of cifthThresholdClearedValue must also be provided before activating the entry. If the value of cifthThresholdType is other than 'rateOfIncreaseExponentXIfSpeed', then the value of cifthThresholdSampleInterval must also be provided before activating the entry. The agent should not allow creation of two entries in the table with the same values of cifthTemplateIndex, cifthThresholdObject, cifthThresholdSeverity, and cifthThresholdDirection. Once an entry has been activated, the values of cifthThresholdObject, cifthThresholdSeverity, cifthThresholdType, and cifthThresholdDirection cannot be modified. In order to use new values of these objects, a new threshold must be defined. The values of cifthThresholdDescr, cifthThresholdFiredValue, cifthThresholdClearedValue, cifthThresholdSampleInterval, and cifthThresholdApsSwitchover may be modified when the entry is active." INDEX { cifthTemplateIndex, cifthThresholdIndex } ::= { cifthThresholdTable 1 } CifthThresholdEntry ::= SEQUENCE { cifthThresholdIndex CifthThresholdIndex, cifthThresholdDescr SnmpAdminString, cifthThresholdObject OBJECT IDENTIFIER, cifthThresholdSeverity CifthThresholdSeverity, cifthThresholdType INTEGER, cifthThresholdDirection INTEGER, cifthThresholdFiredValue Integer32, cifthThresholdClearedValue Integer32, cifthThresholdSampleInterval Unsigned32, cifthThresholdApsSwitchover TruthValue, cifthThresholdRowStatus RowStatus } cifthThresholdIndex OBJECT-TYPE SYNTAX CifthThresholdIndex MAX-ACCESS not-accessible STATUS current DESCRIPTION "An arbitrary integer that uniquely identifies a threshold in a threshold template. The value for each threshold must remain constant when the agent's network management system is rebooted or re-initialized." ::= { cifthThresholdEntry 1 } cifthThresholdDescr OBJECT-TYPE SYNTAX SnmpAdminString (SIZE(0..255)) MAX-ACCESS read-create STATUS current DESCRIPTION "A description of the threshold's function and use. The description must not include carriage returns." DEFVAL { "" } ::= { cifthThresholdEntry 2 } cifthThresholdObject OBJECT-TYPE SYNTAX OBJECT IDENTIFIER MAX-ACCESS read-create STATUS current DESCRIPTION "The object to be compared against the threshold values. The object must be defined in a table indexed only by ifIndex. All of the instance portion of the object identifier is truncated, since the instance(s) to be compared against the threshold are identified using the cifthTemplateIfAssignTable. If the object has syntax 'Integer32', 'Unsigned32', or 'Gauge32', then cifthThresholdType should be set to 'absoluteValue'. If the object has syntax 'Counter32' or 'Counter64', then cifthThresholdType should be set to 'deltaValue' or 'rateOfIncreaseExponentXIfSpeed'." ::= { cifthThresholdEntry 3 } cifthThresholdSeverity OBJECT-TYPE SYNTAX CifthThresholdSeverity MAX-ACCESS read-create STATUS current DESCRIPTION "This object specifies the severity associated with the condition when the threshold is exceeded." ::= { cifthThresholdEntry 4 } cifthThresholdType OBJECT-TYPE SYNTAX INTEGER { absoluteValue(1), deltaValue(2), rateOfIncreaseExponentXIfSpeed(3) } MAX-ACCESS read-create STATUS current DESCRIPTION "The manner in which to compare cifthThresholdObject to cifthThresholdFiredValue and cifthThresholdClearedValue. The value 'absoluteValue' indicates that the value of cifthThresholdObject is to be compared directly to cifthThresholdFiredValue or cifthThresholdClearedValue. The value 'deltaValue' indicates that the difference between two successive samples of cifthThresholdObject is to be compared to cifthThresholdFiredValue or cifthThresholdClearedValue. The polling interval between successive samples is defined in cifthThresholdSampleInterval. The value 'rateOfIncreaseExponentXIfSpeed' indicates that the rate of increase of cifthThresholdObject is to be compared to the negated value of cifthThresholdFiredValue used as the exponent of 10, times the value of ifSpeed (if the value of ifSpeed is less than the maximum value) or ifHighSpeed (otherwise). For example, a value of cifthThresholdFiredValue of 5 on a gigabit ethernet interface indicates a threshold of 10^-5 times the interface speed, which is equal to 10,000 per second. When the value of this object is 'rateOfIncreaseExponentXIfSpeed', the polling interval between successive samples is determined automatically by the agent. When the object identified by cifthThresholdObject is a counter, a threshold type of 'deltaValue' or 'rateOfIncreaseExponentXIfSpeed' should be used. When the object identified by cifthThresholdObject is not a counter, a threshold type of 'absoluteValue' should be used." ::= { cifthThresholdEntry 5 } cifthThresholdDirection OBJECT-TYPE SYNTAX INTEGER { rising(1), falling(2) } MAX-ACCESS read-create STATUS current DESCRIPTION "This object indicates which direction of movement causes the threshold to fire. The value 'rising' indicates that the threshold is fired when the current sampled value is numerically greater than or equal to the value of cifthThresholdFiredValue, and the threshold was considered to be cleared at the last sampling interval. If the value of the corresponding cifthTemplateNotifyHoldDownType object is 'fireAndClearThresholds', the threshold is cleared when the current sampled value is less than the value of cifthThresholdClearedValue, and the threshold was considered to be fired at the last sampling interval. If the value of the corresponding cifthTemplateNotifyHoldDownType object is other than 'fireAndClearThresholds', the threshold is cleared when the current sampled value is less than the value of cifthThresholdFiredValue, and the threshold was considered to be fired at the last sampling interval. The value 'falling' indicates that the threshold is fired when the current sampled value is numerically less than or equal to the value of cifthThresholdFiredValue, and the threshold was considered to be cleared at the last sampling interval. If the value of the corresponding cifthTemplateNotifyHoldDownType object is 'fireAndClearThresholds', the threshold is cleared when the current sampled value is greater than the value of cifthThresholdClearedValue, and the threshold was considered to be fired at the last sampling interval. If the value of the corresponding cifthTemplateNotifyHoldDownType object is other than 'fireAndClearThresholds', the threshold is cleared when the current sampled value is greater than the value of cifthThresholdFiredValue, and the threshold was considered to be fired at the last sampling interval." DEFVAL { rising } ::= { cifthThresholdEntry 6 } cifthThresholdFiredValue OBJECT-TYPE SYNTAX Integer32 (-2147483648..2147483647) MAX-ACCESS read-create STATUS current DESCRIPTION "A threshold value to check against the object identified in cifthThresholdObject. If the value of cifthThresholdDirection is 'rising', then the threshold is fired when the current sampled value (absolute, delta, or rate of increase, depending on the value of cifthThresholdType) of the object identified in cifthThresholdObject is greater than or equal to this value. If the value of cifthThresholdDirection is 'falling', then the threshold is fired when the current sampled value (absolute, delta, or rate of increase, depending on the value of cifthThresholdType) of the object identified in cifthThresholdObject is less than or equal to this value." ::= { cifthThresholdEntry 7 } cifthThresholdClearedValue OBJECT-TYPE SYNTAX Integer32 (-2147483648..2147483647) MAX-ACCESS read-create STATUS current DESCRIPTION "A threshold value to check against the object identified in cifthThresholdObject. If the value of cifthThresholdDirection is 'rising', then the threshold is cleared when the current sampled value (absolute, delta, or rate of increase, depending on the value of cifthThresholdType) of the object identified in cifthThresholdObject is less than this value. If the value of cifthThresholdDirection is 'falling', then the threshold is cleared when the current sampled value (absolute, delta, or rate of increase, depending on the value of cifthThresholdType) of the object identified in cifthThresholdObject is greater than this value. This object is instantiated only when the value of cifthTemplateNotifyHoldDownType in the cifthTemplateEntry with the same value of cifthTemplateIndex is 'fireAndClearThresholds'." ::= { cifthThresholdEntry 8 } cifthThresholdSampleInterval OBJECT-TYPE SYNTAX Unsigned32 (5..900000) UNITS "milliseconds" MAX-ACCESS read-create STATUS current DESCRIPTION "The number of milliseconds to wait between samples of the object identified in cifthThresholdObject. To encourage consistency in sampling, the interval is measured from the beginning of one check to the beginning of the next and the timer is restarted immediately when it expires, not when the check completes. This object is not instantiated when the value of cifthThresholdType is 'rateOfIncreaseExponentXIfSpeed'." ::= { cifthThresholdEntry 9 } cifthThresholdApsSwitchover OBJECT-TYPE SYNTAX TruthValue MAX-ACCESS read-create STATUS current DESCRIPTION "This object indicates whether automatic protection switching (APS) switchover should be triggered, if applicable, when the threshold is fired. The value of this object takes effect when the template identified by cifthTemplateIndex is assigned to an interface that is part of an APS group. One way to configure an interface in an APS group is using the cApsChanConfigTable in the CISCO-APS-MIB." DEFVAL { false } ::= { cifthThresholdEntry 10 } cifthThresholdRowStatus OBJECT-TYPE SYNTAX RowStatus MAX-ACCESS read-create STATUS current DESCRIPTION "This object is used to create and delete thresholds in templates. A new entry can only be created when there is an active entry in the cifthTemplateTable with the same value of cifthTemplateIndex. The values of cifthThresholdObject, cifthThresholdSeverity, cifthThresholdType, and cifthThresholdFiredValue must be provided before activating the entry. If the value of cifthTemplateNotifyHoldDownType in the cifthTemplateEntry with the same value of cifthTemplateIndex is 'fireAndClearThresholds', then the value of cifthThresholdClearedValue must also be provided before activating the entry. If the value of cifthThresholdType is other than 'rateOfIncreaseExponentXIfSpeed', then the value of cifthThresholdSampleInterval must also be provided before activating the entry. When an entry is activated, if there are any entries in cifthTemplateIfAssignTable with the same value of cifthTemplateIndex, then the threshold is activated on all interfaces identified in those entries that have instances of the object identified by cifthThresholdObject. When an entry is destroyed, if there are any entries in cifthTemplateIfAssignTable with the same value of cifthTemplateIndex, then the threshold is de-activated on the interfaces identified in those entries. If there are any entries in cifthIfThresholdFiredTable with cifthIfThresholdFiredTemplate value equal to this value of cifthTemplateIndex, then the bit in cifthIfThresholdsFired corresponding to this threshold is cleared in all such entries. After the entry has been activated, this object cannot be set to any value other than 'destroy'. The row status never changes to 'notInService' after reaching the value 'active'." ::= { cifthThresholdEntry 11 } -- Interface Assignment Table cifthTemplateIfLastChange OBJECT-TYPE SYNTAX TimeStamp MAX-ACCESS read-only STATUS current DESCRIPTION "This object specifies the value of sysUpTime at the last time there was either a change to any object in any entry in cifthTemplateIfAssignTable, or an entry was created or destroyed in cifthTemplateIfAssignTable. If no change to cifthTemplateIfAssignTable has occurred since the last re-initialization of the local network management subsystem, then this object contains a zero value." ::= { cifthTemplateIfAssignGroup 1 } cifthTemplateIfAssignTable OBJECT-TYPE SYNTAX SEQUENCE OF CifthTemplateIfAssignEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "This table specifies the assignment of threshold templates to specific interfaces. Each threshold template may be assigned to multiple interfaces. Each interface may have multiple threshold templates assigned to it." ::= { cifthTemplateIfAssignGroup 2 } cifthTemplateIfAssignEntry OBJECT-TYPE SYNTAX CifthTemplateIfAssignEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "An entry describing the assignment of a particular threshold template to a particular interface. The entry is created using the cifthTemplateIfAssignRowStatus object." INDEX { cifthTemplateIndex, cifthTemplateIfAssignInterface } ::= { cifthTemplateIfAssignTable 1 } CifthTemplateIfAssignEntry ::= SEQUENCE { cifthTemplateIfAssignInterface InterfaceIndex, cifthTemplateIfAssignOperStatus INTEGER, cifthTemplateIfAssignRowStatus RowStatus } cifthTemplateIfAssignInterface OBJECT-TYPE SYNTAX InterfaceIndex MAX-ACCESS not-accessible STATUS current DESCRIPTION "This object identifies an interface to which the template is assigned." ::= { cifthTemplateIfAssignEntry 1 } cifthTemplateIfAssignOperStatus OBJECT-TYPE SYNTAX INTEGER { up(1), down(2) } MAX-ACCESS read-only STATUS current DESCRIPTION "This object indicates whether the threshold template identified by cifthTemplateIndex is operational on the interface identified by cifthTemplateIfAssignInterface. When the value of this object is 'up', this indicates that the thresholds in this template (identified by cifthTemplateIndex) are activated on this interface, with the following exception: If a threshold is defined on an object that does not have an instance for this interface, then the threshold is not activated on this interface. If any of the thresholds are being exceeded, then a corresponding entry exists in the cifthIfThresholdFiredTable. When the value of this object is 'down', this indicates that all thresholds in the template are de-activated on this interface and there is no corresponding entry in the cifthIfThresholdFiredTable, regardless of whether any of the thresholds in the template are being exceeded on this interface. One reason for a template not to be operational on an interface to which it is assigned is when the interface has two (or more) templates assigned to it that contain thresholds on the same object with the same severity and direction, i.e., thresholds with the same values of cifthThresholdObject, cifthThresholdSeverity, and cifthThresholdDirection. This may occur when a template is assigned to the interface, or when a threshold is added to a template that is already active on the interface. When this occurs, the implementation may operate on both (or all) threshold values, or it may take down one (or more) of the templates on this interface, which is indicated by changing the value of this object from 'up' to 'down'." ::= { cifthTemplateIfAssignEntry 2 } cifthTemplateIfAssignRowStatus OBJECT-TYPE SYNTAX RowStatus MAX-ACCESS read-create STATUS current DESCRIPTION "This object is used to create and delete entries in the table, assigning templates to interfaces and removing templates from interfaces, respectively. A new entry can only be created when there is an active entry in the cifthTemplateTable with the same value of cifthTemplateIndex. When an entry is activated, the thresholds in this template (identified by cifthTemplateIndex) are activated on this interface, with the following exception: If a threshold is defined on an object that does not have an instance for this interface, then the threshold is not activated on this interface. When an entry is destroyed, all thresholds in the template are de-activated on this interface and the corresponding entry in the cifthIfThresholdFiredTable is deleted, if it exists. After the entry has been activated, this object cannot be set to any value other than 'destroy'. The row status never changes to 'notInService' after reaching the value 'active'." ::= { cifthTemplateIfAssignEntry 3 } -- Interface Threshold Fired Group cifthThresholdFiredNotifyEnable OBJECT-TYPE SYNTAX CifthThresholdSeverityOrZero MAX-ACCESS read-write STATUS current DESCRIPTION "This object specifies the minimum severity threshold governing the generation of cifthIfThresholdFired and cifthIfThresholdCleared notifications. For example, if the value of this object is set to 'degrade', then the agent generates these notifications if and only if the severity of the threshold being exceeded is 'degrade' or 'fail'. When the value is other than '0', the generation of cifthTemplateIfStatusChange notifications is also enabled. The value of '0' disables the generation of all notifications. By default, the value of this object is set to '0'." ::= { cifthIfThresholdFiredGroup 1 } cifthThresholdFiredLastChange OBJECT-TYPE SYNTAX TimeStamp MAX-ACCESS read-only STATUS current DESCRIPTION "This object specifies the value of sysUpTime at the last time there was either a change to any object in any entry in cifthIfThresholdFiredTable, or an entry was added or deleted in cifthIfThresholdFiredTable. If no change to cifthIfThresholdFiredTable has occurred since the last re-initialization of the local network management subsystem, then this object contains a zero value." ::= { cifthIfThresholdFiredGroup 2 } cifthIfThresholdFiredTable OBJECT-TYPE SYNTAX SEQUENCE OF CifthIfThresholdFiredEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "This table indicates the interfaces that currently have threshold fired conditions." ::= { cifthIfThresholdFiredGroup 3 } cifthIfThresholdFiredEntry OBJECT-TYPE SYNTAX CifthIfThresholdFiredEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "An entry indicating an interface that currently has one or more threshold fired conditions based on one template." INDEX { ifIndex, cifthIfThresholdFiredTemplate } ::= { cifthIfThresholdFiredTable 1 } CifthIfThresholdFiredEntry ::= SEQUENCE { cifthIfThresholdFiredTemplate CifthTemplateIndex, cifthIfThresholdsFired CifthThresholdList, cifthIfLastThresholdFired CifthThresholdIndex, cifthIfThresholdFiredLstChange TimeStamp, cifthIfThresholdFiredLstSeverity CifthThresholdSeverity, cifthIfThresholdFiredMaxSeverity CifthThresholdSeverity } cifthIfThresholdFiredTemplate OBJECT-TYPE SYNTAX CifthTemplateIndex MAX-ACCESS not-accessible STATUS current DESCRIPTION "This object specifies a template for which one or more of the thresholds are fired on this interface." ::= { cifthIfThresholdFiredEntry 1 } cifthIfThresholdsFired OBJECT-TYPE SYNTAX CifthThresholdList MAX-ACCESS read-only STATUS current DESCRIPTION "This object specifies those thresholds that are currently being exceeded on this interface. If a threshold is currently being exceeded (i.e., the threshold is fired) on the interface, then the corresponding bit in the threshold list is set to one. Otherwise, the bit will be set to zero, or the bit will not be present. Only the first N octets are present in the threshold list, such that the highest octet present has at least one bit set to '1'. All higher octets with value '0' are truncated." ::= { cifthIfThresholdFiredEntry 2 } cifthIfLastThresholdFired OBJECT-TYPE SYNTAX CifthThresholdIndex MAX-ACCESS read-only STATUS current DESCRIPTION "This object specifies the last threshold fired or cleared on the interface." ::= { cifthIfThresholdFiredEntry 3 } cifthIfThresholdFiredLstChange OBJECT-TYPE SYNTAX TimeStamp MAX-ACCESS read-only STATUS current DESCRIPTION "This object specifies the value of sysUpTime at the last time a threshold was fired or cleared on the interface." ::= { cifthIfThresholdFiredEntry 4 } cifthIfThresholdFiredLstSeverity OBJECT-TYPE SYNTAX CifthThresholdSeverity MAX-ACCESS read-only STATUS current DESCRIPTION "This object specifies the severity of the threshold that was last fired or cleared on the interface." ::= { cifthIfThresholdFiredEntry 5 } cifthIfThresholdFiredMaxSeverity OBJECT-TYPE SYNTAX CifthThresholdSeverity MAX-ACCESS read-only STATUS current DESCRIPTION "This object specifies the highest severity among the thresholds that are currently being exceeded on this interface." ::= { cifthIfThresholdFiredEntry 6 } -- Notifications cIfThresholdMIBNotifications OBJECT IDENTIFIER ::= { ciscoIfThresholdMIB 2 } cifthMIBNotificationsPrefix OBJECT IDENTIFIER ::= { cIfThresholdMIBNotifications 0 } cifthIfThresholdFired NOTIFICATION-TYPE OBJECTS { cifthIfLastThresholdFired, cifthIfThresholdFiredLstChange, cifthIfThresholdFiredLstSeverity } STATUS current DESCRIPTION "The agent generates this notification when a threshold defined in a template is asserted on an interface. If a threshold is asserted for a given interface and template, cifthTemplateNotifyHoldDownTime is set to 'holdDownTimer' for that template, and this notification has recently been sent for the same threshold on the same interface, then this notification may be suppressed." ::= { cifthMIBNotificationsPrefix 1 } cifthIfThresholdCleared NOTIFICATION-TYPE OBJECTS { cifthIfLastThresholdFired, cifthIfThresholdFiredLstChange, cifthIfThresholdFiredLstSeverity } STATUS current DESCRIPTION "The agent generates this notification when a threshold, that has previously fired, is cleared on an interface. If a threshold is cleared for a given interface and template, cifthTemplateNotifyHoldDownTime is set to 'holdDownTimer' for that template, and this notification has recently been sent for the same threshold on the same interface, then this notification may be suppressed." ::= { cifthMIBNotificationsPrefix 2 } cifthTemplateIfStatusChange NOTIFICATION-TYPE OBJECTS { cifthTemplateIfAssignOperStatus } STATUS current DESCRIPTION "The agent generates this notification when a template comes up or goes down on an interface to which it is assigned, i.e., when the value of cifthTemplateIfAssignOperStatus changes. If a template becomes operationally down on an interface upon activation of a new entry in the cifthTemplateIfAssignTable, the agent generates this notification. The agent need not generate this notification when a new entry in the cifthTemplateIfAssignTable is activated, if the template becomes operational on the interface. The agent need not generate this notification when an entry in the cifthTemplateIfAssignTable is destroyed." ::= { cifthMIBNotificationsPrefix 3 } -- Conformance Information cIfThresholdMIBConformance OBJECT IDENTIFIER ::= { ciscoIfThresholdMIB 3 } cIfThresholdMIBCompliances OBJECT IDENTIFIER ::= { cIfThresholdMIBConformance 1 } cIfThresholdMIBGroups OBJECT IDENTIFIER ::= { cIfThresholdMIBConformance 2 } -- Compliance Statement cIfThresholdMIBCompliance MODULE-COMPLIANCE STATUS current DESCRIPTION "The compliance statement for entities that implement the Cisco Interface Threshold MIB." MODULE -- this module MANDATORY-GROUPS { cIfThresholdTemplateGroup, cIfThresholdFiredGroup, cIfThresholdNotifsGroup } OBJECT cifthTemplateNotifyHoldDownType DESCRIPTION "At least one of the codepoints 'holdDownTimer' and 'fireAndClearThresholds' must be supported." GROUP cifthHoldDownTimerGroup DESCRIPTION "This group is required only for entities that support suppression of excess notifications in a short time interval based on a timer, i.e., systems that support the cifthTemplateNotifyHoldDownType value 'holdDownTimer'. At least one of this group and cifthHoldDownHysteresisGroup must be supported." GROUP cifthHoldDownHysteresisGroup DESCRIPTION "This group is required only for entities that prevent excess notifications in a short time interval by using hysteresis, i.e., systems that support the cifthTemplateNotifyHoldDownType value 'fireAndClearThresholds'. At least one of this group and cifthHoldDownTimerGroup must be supported." OBJECT cifthThresholdType DESCRIPTION "At least one of the codepoints 'deltaValue' and 'rateOfIncreaseExponentXIfSpeed' must be supported." GROUP cifthApsGroup DESCRIPTION "This group is required only for entities that support the Cisco Interface Threshold MIB and support triggering of automatic protection switching (APS) based on thresholds of interface counters." GROUP cifthTemplateIfNotifsGroup DESCRIPTION "This group is required only for entities that do not allow multiple threshold values (in different threshold templates) of the same severity and direction on the same object to be applied on one interface." ::= { cIfThresholdMIBCompliances 1 } -- Units of Conformance cIfThresholdTemplateGroup OBJECT-GROUP OBJECTS { cifthTemplateIndexNext, cifthTemplateLastChange, cifthTemplateName, cifthTemplateNotifyHoldDownType, cifthTemplateRowStatus, cifthThresholdLastChange, cifthThresholdDescr, cifthThresholdObject, cifthThresholdSeverity, cifthThresholdType, cifthThresholdDirection, cifthThresholdFiredValue, cifthThresholdSampleInterval, cifthThresholdRowStatus, cifthTemplateIfLastChange, cifthTemplateIfAssignOperStatus, cifthTemplateIfAssignRowStatus } STATUS current DESCRIPTION "A collection of mandatory managed objects for configuration of threshold templates." ::= { cIfThresholdMIBGroups 1 } cIfThresholdFiredGroup OBJECT-GROUP OBJECTS { cifthThresholdFiredNotifyEnable, cifthThresholdFiredLastChange, cifthIfThresholdsFired, cifthIfLastThresholdFired, cifthIfThresholdFiredLstChange, cifthIfThresholdFiredLstSeverity, cifthIfThresholdFiredMaxSeverity } STATUS current DESCRIPTION "A collection of mandatory managed objects for monitoring interfaces where thresholds have been exceeded." ::= { cIfThresholdMIBGroups 2 } cifthHoldDownTimerGroup OBJECT-GROUP OBJECTS { cifthTemplateNotifyHoldDownTime } STATUS current DESCRIPTION "A collection of managed objects for configuration of a timer-based mechanism for suppression of excess notifications in a short time interval." ::= { cIfThresholdMIBGroups 3 } cifthHoldDownHysteresisGroup OBJECT-GROUP OBJECTS { cifthThresholdClearedValue } STATUS current DESCRIPTION "A collection of managed objects for configuration of threshold values used to assert that the threshold is no longer being exceeded. These objects are part of the hysteresis mechanism used to prevent excess notifications in a short time interval." ::= { cIfThresholdMIBGroups 4 } cifthApsGroup OBJECT-GROUP OBJECTS { cifthThresholdApsSwitchover } STATUS current DESCRIPTION "A collection of managed objects for configuration of APS switchover triggers based on interface thresholds." ::= { cIfThresholdMIBGroups 5 } cIfThresholdNotifsGroup NOTIFICATION-GROUP NOTIFICATIONS { cifthIfThresholdFired, cifthIfThresholdCleared } STATUS current DESCRIPTION "A collection of notifications generated when an interface has a threshold fired or a threshold cleared condition." ::= { cIfThresholdMIBGroups 6 } cifthTemplateIfNotifsGroup NOTIFICATION-GROUP NOTIFICATIONS { cifthTemplateIfStatusChange } STATUS current DESCRIPTION "A collection of notifications related to the assignment of templates to interfaces." ::= { cIfThresholdMIBGroups 7 } END