-- =============================================================================== -- -- Atkk QoS objects -- CENTRECOM-QOS-MIB DEFINITIONS ::= BEGIN IMPORTS MODULE-IDENTITY FROM SNMPv2-SMI OBJECT-TYPE FROM RFC-1212 TruthValue FROM SNMPv2-TC DisplayString FROM RFC1213-MIB RowStatus FROM SNMPv2-TC atiVlanIfIndex FROM CENTRECOM-VLAN-MIB extSwitchMIB FROM CENTRECOM-MIB; atiQos MODULE-IDENTITY LAST-UPDATED "9803020000Z" ORGANIZATION "Allied Telesis K.K" CONTACT-INFO "www1.allied-telesis.co.jp/GIGA" DESCRIPTION "Atkk Quality-of-Service objects" ::= { extSwitchMIB 5 } atiQosCommon OBJECT IDENTIFIER ::= { atiQos 1 } -- -- Select QoS Mode -- atiQosMode OBJECT-TYPE SYNTAX INTEGER { ingress(1), egress(2) } ACCESS read-write STATUS mandatory DESCRIPTION "Indicates which QoS mode the device should use. ingress(1) applies priority-based QoS based on the incoming packet's destination IP or MAC address, 802.1p priority, PACE(tm), Source Port or VLAN. egress(2) applies priority- and bandwidth-based QoS based on destination IP or MAC address or VLAN." ::= { atiQosCommon 4 } -- -- Reset all QoS settings to defaults -- atiQosUnconfigure OBJECT-TYPE SYNTAX TruthValue ACCESS read-write STATUS mandatory DESCRIPTION "Setting this to true will reset all QoS settings in the device to factory defaults. Reads from this value return an undefined value." ::= { atiQosCommon 5 } -- -- QoS Profile table -- atiQosProfileTable OBJECT-TYPE SYNTAX SEQUENCE OF AtiQosProfileEntry ACCESS not-accessible STATUS mandatory DESCRIPTION "This table lists QoS profiles." ::= { atiQosCommon 6 } atiQosProfileEntry OBJECT-TYPE SYNTAX AtiQosProfileEntry ACCESS not-accessible STATUS mandatory DESCRIPTION "An individual QoS profile Entry." INDEX {atiQosProfileIndex} ::= {atiQosProfileTable 1} AtiQosProfileEntry ::= SEQUENCE { atiQosProfileIndex INTEGER , atiQosProfileName DisplayString, atiQosProfileMinBw INTEGER, atiQosProfileMaxBw INTEGER, atiQosProfilePriority INTEGER, atiQosProfileRowStatus RowStatus } atiQosProfileIndex OBJECT-TYPE SYNTAX INTEGER (1..65535) ACCESS read-write STATUS mandatory DESCRIPTION "An index that uniquely identifies an entry in the qos table." ::= { atiQosProfileEntry 1} atiQosProfileName OBJECT-TYPE SYNTAX DisplayString (SIZE (0..127)) ACCESS read-write STATUS mandatory DESCRIPTION "A unique qos profile name." ::= {atiQosProfileEntry 2} atiQosProfileMinBw OBJECT-TYPE SYNTAX INTEGER ACCESS read-write STATUS mandatory DESCRIPTION "The minumum percentage of bandwidth that this queue requires. The Switch is required to provide the minumum amount of bandwidth to the queue. The lowest possible value is 0%." ::= {atiQosProfileEntry 3 } atiQosProfileMaxBw OBJECT-TYPE SYNTAX INTEGER ACCESS read-write STATUS mandatory DESCRIPTION "The maximum percentage of bandwidth that this queue is permitted to use" ::= {atiQosProfileEntry 4 } atiQosProfilePriority OBJECT-TYPE SYNTAX INTEGER { low(1), normal(2), medium(3), high(4) } ACCESS read-write STATUS mandatory DESCRIPTION "The level of priority in which this queue will be serviced by the Switch." ::= {atiQosProfileEntry 5 } atiQosProfileRowStatus OBJECT-TYPE SYNTAX RowStatus ACCESS read-write STATUS mandatory DESCRIPTION "The status of the atiQosProfile entry. This OBJECT can be set to: active(1) createAndGo(4) createAndWait(5) destroy(6) The following values may be read: active(1) notInService(2) notReady(3). Setting this object to createAndGo(4) causes the agent to attempt to create and commit the row based on the contents of the objects in the row. If all necessary information is present in the row and the values are acceptible to the agent, the agent will change the status to active(1). If any of the necessary objects are not available, the agent will reject the creation request. Setting this object to createAndWait(5) causes a row in this table to be created. The agent sets the status to notInService(2) if all of the information is present in the row and the values are acceptable to the agent; otherwise, the agent sets the status to notReady(3). Setting this object to active(1) is only valid when the current status is active(1) or notInService(2). When the state of the row transitions is set to active(1), the agent creates the corresponding row in the ifTable.. Setting this object to destroy(6) will remove the corresponding QoS Profile Entry. In order for a set of this object to destroy(6) to succeed, all dependencies on this row must have been removed. These will include any stacking dependencies in the ifStackTable and any protocol specific tables dependencies." ::= { atiQosProfileEntry 6 } -- -- VLAN-based QoS Table -- atiQosByVlanMappingTable OBJECT-TYPE SYNTAX SEQUENCE OF AtiQosByVlanMappingEntry ACCESS not-accessible STATUS mandatory DESCRIPTION "Table to associate a Vlan with the QoS profile that the Vlan is using. Every Vlan is assigned a Qos Profile and hence there is an entry in this table corresponding to every entry in the atiVlanIfTable." ::= { atiQosCommon 7 } atiQosByVlanMappingEntry OBJECT-TYPE SYNTAX AtiQosByVlanMappingEntry ACCESS not-accessible STATUS mandatory DESCRIPTION "The QoS associated with a particular Vlan." INDEX {atiVlanIfIndex} ::= {atiQosByVlanMappingTable 1} AtiQosByVlanMappingEntry ::= SEQUENCE { atiQosByVlanMappingQosProfileIndex INTEGER } atiQosByVlanMappingQosProfileIndex OBJECT-TYPE SYNTAX INTEGER (1..65535) ACCESS read-write STATUS mandatory DESCRIPTION "Value of atiQosProfileIndex that uniquely identifies a QoS Profile entry in atiQosProfileTable. This indicates the QoS to be given to traffic for this Vlan in the absence of any other more specific configuration information for this traffic." ::= { atiQosByVlanMappingEntry 1 } END