ATM-FORUM-AUTO-CONFIG DEFINITIONS ::= BEGIN IMPORTS DisplayString, RowPointer FROM SNMPv2-TC OBJECT-TYPE FROM SNMPv2-SMI atmForum, atmForumUni FROM ATM-FORUM-TC-MIB TRAP-TYPE FROM RFC-1215; -- ---------------------------------------------------------------- -- ATM Forum ILMI Extension for Auto Configuration -- This definition contains the following tables -- ATM Service Type Table -- ATM Service Connection Information Table -- AAL1 Profile Table -- AAL3/4 Profile Table -- AAL 5 Profile Table -- AAL 2 Profile Table -- -------------------------------------------------------------- atmfAutoConfigGroup OBJECT IDENTIFIER ::= { atmForumUni 12 } ------------------------------------------------------------------ -- ATM Forum ILMI Extension for Auto Configuration -- ATM Service Type ------------------------------------------------------------------ atmfAtmServiceTypeTable OBJECT-TYPE SYNTAX SEQUENCE OF AtmfAtmServiceTypeEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "The ATM Forum ILMI Auto Configuration Extension ATM Service Type Information. " ::= { atmfAutoConfigGroup 1 } atmfAtmServiceTypeEntry OBJECT-TYPE SYNTAX AtmfAtmServiceTypeEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "An entry in the service type table describes the reference information about a service that may be associated with individual ATM connections for the purpose of auto- configuration. This information describe the name and sub- name of the service, the client layer protocol using the ATM service, the TM 4.0 service category, and the TM 4.0 conformance definition." INDEX { atmfAtmServiceTypeIndex } ::= { atmfAtmServiceTypeTable 1 } AtmfAtmServiceTypeEntry ::= SEQUENCE { atmfAtmServiceTypeIndex INTEGER, atmfAtmServiceProviderName DisplayString, atmfAtmServiceName DisplayString, atmfAtmServiceSubName DisplayString, atmfAtmServiceClient DisplayString, atmfAtmServiceTMCategory INTEGER, atmfAtmServiceTMConformanceDef INTEGER } atmfAtmServiceTypeIndex OBJECT-TYPE SYNTAX INTEGER (1..2147483647) MAX-ACCESS read-only STATUS current DESCRIPTION "A number between which identifies the entry in the Service Type Table. " ::= { atmfAtmServiceTypeEntry 1 } atmfAtmServiceProviderName OBJECT-TYPE SYNTAX DisplayString MAX-ACCESS read-only STATUS current DESCRIPTION "This string identifies the name of the service provider for the service described in this profile. The value of this attribute should not set to NULL." ::= { atmfAtmServiceTypeEntry 2 } atmfAtmServiceName OBJECT-TYPE SYNTAX DisplayString MAX-ACCESS read-only STATUS current DESCRIPTION "This string identifies the name of the service described in this profile. The value of this attribute should not be set to NULL. " ::= { atmfAtmServiceTypeEntry 3 } atmfAtmServiceSubName OBJECT-TYPE SYNTAX DisplayString MAX-ACCESS read-only STATUS current DESCRIPTION "This string identifies the sub-name of the service described in this profile. A Service may have zero or more sub-names, each with its own service type profile. " ::= { atmfAtmServiceTypeEntry 4 } atmfAtmServiceClient OBJECT-TYPE SYNTAX DisplayString MAX-ACCESS read-only STATUS current DESCRIPTION "This string identifies the client protocol of the service described in this profile. A Service (sub-service) may have zero or more described client, each with its own service type profile. " ::= { atmfAtmServiceTypeEntry 5 } atmfAtmServiceTMCategory OBJECT-TYPE SYNTAX INTEGER { other (1), cbr (2), rtVbr (3), nrtVbr (4), abr (5), ubr (6), gfr (7) } MAX-ACCESS read-only STATUS current DESCRIPTION "The TM 4.0 Service category used for this service type. Indicates CBR, rt-VBR, nrt-VBR, ABR, UBR, (or GFR)" ::= { atmfAtmServiceTypeEntry 6 } atmfAtmServiceTMConformanceDef OBJECT-TYPE SYNTAX INTEGER { none (0), other(1), cbr1 (2), vbr1 (3), vbr2 (4), vbr3 (5), ubr1 (6), ubr2 (7), abr (8), gfr1 (9), gfr2 (10) } MAX-ACCESS read-only STATUS current DESCRIPTION "The TM 4.1 conformance definition used for this service type. Indicates CBR.1, VBR.1, VBR.2, VBR.3, UBR.1, UBR.2, ABR, GFR.1, or GFR.2. " ::= { atmfAtmServiceTypeEntry 7 } ------------------------------------------------------------------ -- ATM Forum ILMI Extension for Auto Configuration -- ATM Service Connection Information ------------------------------------------------------------------ atmfAtmServiceConnInfoTable OBJECT-TYPE SYNTAX SEQUENCE OF AtmfAtmServiceConnInfoEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "The ATM Forum ILMI Auto Configuration Extension ATM Service Connection Information. " ::= { atmfAutoConfigGroup 2 } atmfAtmServiceConnInfoEntry OBJECT-TYPE SYNTAX AtmfAtmServiceConnInfoEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "An entry in the service connection information table describes the ATM connection that provides a service across an ATM interface. The connection is identified by port and VPI/VCI value. Information about the connection includes the connection type (VP or VC, SVC or PVC), and the association of the connection with a service type. Specific connection information, such as traffic descriptors, should be accessed in the atmfVpc and atmfVcc tables defined in ILMI. " INDEX { atmfAtmServicePortIndex, atmfAtmServiceVpi, atmfAtmServiceVci } ::= { atmfAtmServiceConnInfoTable 1 } AtmfAtmServiceConnInfoEntry ::= SEQUENCE { atmfAtmServicePortIndex INTEGER, atmfAtmServiceVpi INTEGER, atmfAtmServiceVci INTEGER, atmfAtmServiceSignalId INTEGER, atmfAtmServiceConnServiceIndex INTEGER, atmfAtmServiceConnName DisplayString, atmfAtmServiceConnAALType INTEGER, atmfAtmServiceConnAALIndex INTEGER } atmfAtmServicePortIndex OBJECT-TYPE SYNTAX INTEGER (0..2147483647) MAX-ACCESS read-only STATUS current DESCRIPTION "The value of 0 (zero)has the special meaning of identifying the ATM Interface over which this ILMI message was received. " ::= { atmfAtmServiceConnInfoEntry 1 } atmfAtmServiceVpi OBJECT-TYPE SYNTAX INTEGER (0..255) MAX-ACCESS read-only STATUS current DESCRIPTION "The VPI value of the ATM service connection at the local ATM interface. " ::= { atmfAtmServiceConnInfoEntry 2 } atmfAtmServiceVci OBJECT-TYPE SYNTAX INTEGER (0..65535) MAX-ACCESS read-only STATUS current DESCRIPTION "The VCI value of the ATM service connection at the local ATM interface. If the atmfAtmServiceSignalId indicates that the connection is a VP connection, the value of this attribute shall be set to 0 (zero) and any meaning of this attribute ignored." ::= { atmfAtmServiceConnInfoEntry 3 } atmfAtmServiceSignalId OBJECT-TYPE SYNTAX INTEGER { vcCI(0), vpCI(1) } MAX-ACCESS read-only STATUS current DESCRIPTION "This attribute represents the characteristic information of the layer network domain. It may be set to either VC characteristic information (vcCI) or VP characteristic information (vpCI)." ::= { atmfAtmServiceConnInfoEntry 4 } atmfAtmServiceConnServiceIndex OBJECT-TYPE SYNTAX INTEGER MAX-ACCESS read-only STATUS current DESCRIPTION "The value of this object identifies the row in the atmfAtmServiceTypeTable. This entry represents the association between an ATM service connection and an ATM service type profile that describes it. " ::= { atmfAtmServiceConnInfoEntry 5 } atmfAtmServiceConnName OBJECT-TYPE SYNTAX DisplayString MAX-ACCESS read-only STATUS current DESCRIPTION "This string identifies the name of the service connection. The value of this attribute may be set to NULL. " ::= { atmfAtmServiceConnInfoEntry 6 } atmfAtmServiceConnAALType OBJECT-TYPE SYNTAX INTEGER { none (0), aal1 (1), aal34 (2), aal5 (3), other (4), unknown (5), aal2 (6) } MAX-ACCESS read-only STATUS current DESCRIPTION "Describes the AAL Type of the ATM service connection. A value of none indicates that no AAL is used. The AAL types include AAL1, AAL 3/4, and AAL 5. The value other may be a user-defined AAL type. The unknown type indicates that the AAL type cannot be determined. " ::= { atmfAtmServiceConnInfoEntry 7 } atmfAtmServiceConnAALIndex OBJECT-TYPE SYNTAX INTEGER MAX-ACCESS read-only STATUS current DESCRIPTION "The value of this object identifies the row in the atmfAAL1ProfileTable for AAL 1 connection, the atmfAAL34ProfileTable for AAL3/4 connection, and the atmfAAL5ProfileTable for AAL 5 connections. This entry represents the association between an ATM service connection and an ATM Adaptation Layer profile that describes it. " ::= { atmfAtmServiceConnInfoEntry 8 } ------------------------------------------------------------------ -- ATM Forum ILMI Extension for Auto Configuration -- ATM AAL1 Profile ------------------------------------------------------------------ atmfAAL1ProfileTable OBJECT-TYPE SYNTAX SEQUENCE OF AtmfAAL1ProfileEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "The ATM Forum ILMI Auto Configuration Extension AAL1 Profile Information. " ::= { atmfAutoConfigGroup 3 } atmfAAL1ProfileEntry OBJECT-TYPE SYNTAX AtmfAAL1ProfileEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "An entry in the AAL1 Profile table provides data that describes the AAL1 processing function. " INDEX { atmfAAL1ProfileIndex } ::= { atmfAAL1ProfileTable 1 } AtmfAAL1ProfileEntry ::= SEQUENCE { atmfAAL1ProfileIndex INTEGER, atmfAAL1Subtype INTEGER, atmfAAL1CBRRate INTEGER, atmfAAL1ClkRecoveryType INTEGER, atmfAAL1FEC INTEGER, atmfAAL1SDT INTEGER, atmfAAL1PartiallyFilledCells INTEGER, atmfAAL1CellLossIntegrPeriod INTEGER } atmfAAL1ProfileIndex OBJECT-TYPE SYNTAX INTEGER (1..2147483647) MAX-ACCESS read-only STATUS current DESCRIPTION "A number between which identifies the entry in the AAL1 Profile Table. " ::= { atmfAAL1ProfileEntry 1 } atmfAAL1Subtype OBJECT-TYPE SYNTAX INTEGER { null (0), voiceBand (1), circuitEmulationSynchronous (2), circuitEmulationAsynchronous (3), highQualityAuto (4), video (5) } MAX-ACCESS read-only STATUS current DESCRIPTION "This attribute describes AAL type 1 subtype used by the CBR service application (e.g. 64 KBPS voice band signal transport, circuit transport). " ::= { atmfAAL1ProfileEntry 2 } atmfAAL1CBRRate OBJECT-TYPE SYNTAX INTEGER MAX-ACCESS read-only STATUS current DESCRIPTION "This attribute describes the rate of the CBR service supported by the AAL." ::= { atmfAAL1ProfileEntry 3 } atmfAAL1ClkRecoveryType OBJECT-TYPE SYNTAX INTEGER { synchronous (0), srts(1), adaptive (2) } MAX-ACCESS read-only STATUS current DESCRIPTION "This attribute indicates whether the clock recovery type is synchronous, asynchronous-SRTS(Synchronous Residual Time Stamp), or asynchronous-Adaptive Clock Recovery. " ::= { atmfAAL1ProfileEntry 4 } atmfAAL1FEC OBJECT-TYPE SYNTAX INTEGER { noFEC (0), lossSensitiveSignalFEC (1), delaySensitiveSignalFEC (2) } MAX-ACCESS read-only STATUS current DESCRIPTION "This attribute indicates the FEC method: no FEC, FEC for Loss Sensitive Signal Transport, or FEC for Delay Sensitive Signal Transport. " ::= { atmfAAL1ProfileEntry 5 } atmfAAL1SDT OBJECT-TYPE SYNTAX INTEGER { false (0), true(1) } MAX-ACCESS read-only STATUS current DESCRIPTION "This attribute indicates whether Structured Data Transfer (SDT) has been configured at the AAL. A value of TRUE means SDT has been selected. This attribute value can be set to TRUE only when the Forward Error Correction Type attribute equals noFEC. " ::= { atmfAAL1ProfileEntry 6 } atmfAAL1PartiallyFilledCells OBJECT-TYPE SYNTAX INTEGER MAX-ACCESS read-only STATUS current DESCRIPTION "This attribute identifies the number of leading octets in use." ::= { atmfAAL1ProfileEntry 7 } atmfAAL1CellLossIntegrPeriod OBJECT-TYPE SYNTAX INTEGER MAX-ACCESS read-only STATUS current DESCRIPTION "This attribute represents the time in milliseconds for the cell loss integration period. If cells are lost for this period of time, the Interworking VCC Termination Point entity will generate a cell starvation alarm." ::= { atmfAAL1ProfileEntry 8 } ------------------------------------------------------------------ -- ATM Forum ILMI Extension for Auto Configuration -- ATM AAL3/4 Profile ------------------------------------------------------------------ atmfAAL34ProfileTable OBJECT-TYPE SYNTAX SEQUENCE OF AtmfAAL34ProfileEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "The ATM Forum ILMI Auto Configuration Extension AAL3/4 Profile Information. " ::= { atmfAutoConfigGroup 4 } atmfAAL34ProfileEntry OBJECT-TYPE SYNTAX AtmfAAL34ProfileEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "An entry in the AAL34 Profile table provides data that describes the AAL3/4 processing function. " INDEX { atmfAAL34ProfileIndex } ::= { atmfAAL34ProfileTable 1 } AtmfAAL34ProfileEntry ::= SEQUENCE { atmfAAL34ProfileIndex INTEGER, atmfAAL34MaxCpcsSduSizeForward INTEGER, atmfAAL34MaxCpcsSduSizeBackward INTEGER, atmfAAL34MIDRangeLow INTEGER, atmfAAL34MIDRangeHigh INTEGER, atmfAAL34AALMode INTEGER, atmfAAL34SscsType INTEGER } atmfAAL34ProfileIndex OBJECT-TYPE SYNTAX INTEGER (1..2147483647) MAX-ACCESS read-only STATUS current DESCRIPTION "A number between which identifies the entry in the AAL3/4 Profile Table. " ::= { atmfAAL34ProfileEntry 1 } atmfAAL34MaxCpcsSduSizeForward OBJECT-TYPE SYNTAX INTEGER (1..65535) MAX-ACCESS read-only STATUS current DESCRIPTION "This attribute represents the maximum CPCS_PDU size that will be transmitted over the connection in both the incoming (forward) direction of transmission. " ::= { atmfAAL34ProfileEntry 2 } atmfAAL34MaxCpcsSduSizeBackward OBJECT-TYPE SYNTAX INTEGER (1..65535) MAX-ACCESS read-only STATUS current DESCRIPTION "This attribute represents the maximum CPCS_PDU size that will be transmitted over the connection in both the outgoing (backward) direction of transmission. " ::= { atmfAAL34ProfileEntry 3 } atmfAAL34MIDRangeLow OBJECT-TYPE SYNTAX INTEGER (1..66536) MAX-ACCESS read-only STATUS current DESCRIPTION "This attribute represents the low value of MID supported at the AAL for the supporting VCC." ::= { atmfAAL34ProfileEntry 4 } atmfAAL34MIDRangeHigh OBJECT-TYPE SYNTAX INTEGER (1..66536) MAX-ACCESS read-only STATUS current DESCRIPTION "This attribute represents the high value of MID supported at the AAL for the supporting VCC." ::= { atmfAAL34ProfileEntry 5 } atmfAAL34AALMode OBJECT-TYPE SYNTAX INTEGER { messageAssured (0), messageUnassured (1), streamingAssured (2), streamingUnassured (3) } MAX-ACCESS read-only STATUS current DESCRIPTION "This attribute indicates whether the AAL for the supporting VCC is operating in message mode or streaming mode, assured or unassured. " ::= { atmfAAL34ProfileEntry 6 } atmfAAL34SscsType OBJECT-TYPE SYNTAX INTEGER { null (0), dataAssured (1), dataNonAssured (2), frameRelay (3) } MAX-ACCESS read-only STATUS current DESCRIPTION "This attribute identifies the SSCS type for the AAL. Valid values are NULL, Data SSCS based on SSCOP (assured operation), Data SSCS based on SSCOP (non-assured operation), or Frame Relay SSCS " ::= { atmfAAL34ProfileEntry 7 } ------------------------------------------------------------------ -- ATM Forum ILMI Extension for Auto Configuration -- ATM AAL5 Profile ------------------------------------------------------------------ atmfAAL5ProfileTable OBJECT-TYPE SYNTAX SEQUENCE OF AtmfAAL5ProfileEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "The ATM Forum ILMI Auto Configuration Extension AAL5 Profile Information. " ::= { atmfAutoConfigGroup 5 } atmfAAL5ProfileEntry OBJECT-TYPE SYNTAX AtmfAAL5ProfileEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "An entry in the AAL5 Profile table provides data that describes the AAL5 processing function. " INDEX { atmfAAL5ProfileIndex } ::= { atmfAAL5ProfileTable 1 } AtmfAAL5ProfileEntry ::= SEQUENCE { atmfAAL5ProfileIndex INTEGER, atmfAAL5MaxCpcsSduSizeForward INTEGER, atmfAAL5MaxCpcsSduSizeBackward INTEGER, atmfAAL5AALMode INTEGER, atmfAAL5SscsType INTEGER } atmfAAL5ProfileIndex OBJECT-TYPE SYNTAX INTEGER (1..2147483647) MAX-ACCESS read-only STATUS current DESCRIPTION "A number between which identifies the entry in the AAL5 Profile Table. " ::= { atmfAAL5ProfileEntry 1 } atmfAAL5MaxCpcsSduSizeForward OBJECT-TYPE SYNTAX INTEGER (1..65535) MAX-ACCESS read-only STATUS current DESCRIPTION "This attribute represents the maximum CPCS_PDU size that will be transmitted over the connection in both the incoming (forward) direction of transmission. " ::= { atmfAAL5ProfileEntry 2 } atmfAAL5MaxCpcsSduSizeBackward OBJECT-TYPE SYNTAX INTEGER (1..65535) MAX-ACCESS read-only STATUS current DESCRIPTION "This attribute represents the maximum CPCS_PDU size that will be transmitted over the connection in both the outgoing (backward) direction of transmission. " ::= { atmfAAL5ProfileEntry 3 } atmfAAL5AALMode OBJECT-TYPE SYNTAX INTEGER { messageAssured (0), messageUnassured (1), streamingAssured (2), streamingUnassured (3) } MAX-ACCESS read-only STATUS current DESCRIPTION "This attribute indicates whether the AAL for the supporting VCC is operating in message mode or streaming mode, assured or unassured. " ::= { atmfAAL5ProfileEntry 4 } atmfAAL5SscsType OBJECT-TYPE SYNTAX INTEGER { null (0), dataAssured (1), dataNonAssured (2), frameRelay (3) } MAX-ACCESS read-only STATUS current DESCRIPTION "This attribute identifies the SSCS type for the AAL. Valid values are NULL, Data SSCS based on SSCOP (assured operation), Data SSCS based on SSCOP (non-assured operation), or Frame Relay SSCS " ::= { atmfAAL5ProfileEntry 5 } ------------------------------------------------------------------ -- ATM Forum ILMI Extension for Auto Configuration -- ATM Common AAL2 Profile -- In the case where an AAL2CommonProfileEntry contains parameter(s) -- which is/are set to a value that is/are not supported by the AAL2 -- entity in the ATU-R, the user-side IME must raise an -- atmfAtmServiceConfFail trap towards the network-side IME. The -- atmfAtmServiceConfFailReason should be 'unsupportedAAL' and -- the atmfAtmServiceConfFailOID must point to the -- atmfAAL2CommonProfileEntry that contains the unsupported -- parameter(s). ------------------------------------------------------------------ atmfAAL2CommonProfileTable OBJECT-TYPE SYNTAX SEQUENCE OF AtmfAAL2CommonProfileEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "The ATM Forum ILMI Auto Configuration Extension AAL2 Profile Information. This table contains AAL2 parameters that are common to all AAL2 applications. These parameters are taken from I.363.2, I.366.1 and I.366.2" ::= { atmfAutoConfigGroup 6 } atmfAAL2CommonProfileEntry OBJECT-TYPE SYNTAX AtmfAAL2CommonProfileEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "An atmfAAL2CommonProfileEntry provides AAL2 common parameters of operation that are to be used by the PVC associated with this entry." INDEX { atmfAAL2ProfileIndex } ::= { atmfAAL2CommonProfileTable 1 } AtmfAAL2CommonProfileEntry ::= SEQUENCE { atmfAAL2ProfileIndex INTEGER, atmfAAL2ApplicationIdentifier INTEGER, atmfAAL2ConfigResponsibility INTEGER, atmfAAL2CpsMaxMultiplexedChannels INTEGER, atmfAAL2CpsMaxSduLength INTEGER, atmfAAL2SscsMaxSssarSduLength INTEGER, atmfAAL2SscsSstedStatus INTEGER, atmfAAL2SscsSsadtStatus INTEGER, atmfAAL2SscsServiceCategory INTEGER, atmfAAL2SscsAudioServiceTransport INTEGER, atmfAAL2SscsProfileSource INTEGER, atmfAAL2SscsIeeeOui INTEGER, atmfAAL2SscsPredefinedProfileIdentifier INTEGER, atmfAAL2SscsPcmEncoding INTEGER, atmfAAL2SscsFaxDemodulationTransport INTEGER, atmfAAL2SscsCasSignalingTransport INTEGER, atmfAAL2SscsDtmfDigitPacketTransport INTEGER, atmfAAL2SscsMfR1DigitPacketTransport INTEGER, atmfAAL2SscsMfR2DigitPacketTransport INTEGER, atmfAAL2SscsCircuitModeDataTransport INTEGER, atmfAAL2SscsCircuitModeDataNumChannels INTEGER, atmfAAL2SscsFrameModeDataTransport INTEGER, atmfAAL2SscsFrameModeDataMaxLength INTEGER, atmfAAL2SscopSduLength INTEGER, atmfAAL2SscopUuFieldLength INTEGER } atmfAAL2ProfileIndex OBJECT-TYPE SYNTAX INTEGER MAX-ACCESS read-only STATUS current DESCRIPTION "A number which uniquely identifies the entry in the AAL2 Profile Table." ::= { atmfAAL2CommonProfileEntry 1 } atmfAAL2ApplicationIdentifier OBJECT-TYPE SYNTAX INTEGER MAX-ACCESS read-only STATUS current DESCRIPTION "The application identifier specifies which AAL2 application is using the PVC. In addition it specifies protocol combinations to be used on AAL2 channels between IWFs, i.e. it implicitly configures the use of I.366.1 or I.366.2 for bearer and signalling AAL2 channels. The value of this object should be one of those values given in the administered list of AppIds for AAL2 Applications in section 5 of the ATM Forum document of well-known addresses and assigned codes which can be located at vhttp://www.atmforum.com/atmforum/specs/public_assigned_codes.pdf." ::= { atmfAAL2CommonProfileEntry 2 } atmfAAL2ConfigResponsibility OBJECT-TYPE SYNTAX INTEGER { ilmi (1), lesEoc (2), other (3) } MAX-ACCESS read-only STATUS current DESCRIPTION "This object identifies which management channel is responsible for AAL2 provisioning and auto-configuration. The user-side IME must check the value of this parameter first before configuring the AAL2 for the PVC to determine whether or not this responsibility lies with ILMI. ilmi - if this is selected then the user-side IME must use the AAL2 Profile defined in this entry and associated AAL2 Profile extension table entry to auto-configure the AAL2 for the PVC. lesEoc - if this is selected then the user-side IME must not auto-configure the AAL2 using ILMI. The AAL2 Profile parameters do not need to be provisioned by the network- side IME and with the exception of this object the AAL2 profile parameters in the ILMI MIB are not applicable. The Loop Emulation Service Embedded Operations Channel (LES EOC) shall be used to provision the AAL2 for the PVC. The start-up AAL2 parameters for this PVC must assume the default values specified in the af-vmoa-0145.000 MIB such that the LES EOC is operational. other - if this is selected then the user-side IME must not auto-configure the AAL2 using ILMI. The AAL2 Profile parameters do not need to be provisioned by the network- side IME and with the exception of this object the AAL2 profile parameters in the ILMI MIB are not applicable. Another mechanism will be used to provision the AAL2 at the ATU-R for the PVC." ::= { atmfAAL2CommonProfileEntry 3 } atmfAAL2CpsMaxMultiplexedChannels OBJECT-TYPE SYNTAX INTEGER (1..255) MAX-ACCESS read-only STATUS current DESCRIPTION "Maximum number of multiplexed channels." DEFVAL { 255 } ::= { atmfAAL2CommonProfileEntry 4 } atmfAAL2CpsMaxSduLength OBJECT-TYPE SYNTAX INTEGER (45 | 64) MAX-ACCESS read-only STATUS current DESCRIPTION "Maximum CPS-SDU size given in octets. This parameter is bidirectional, i.e. its value applies to both directions of the AAL2 connection." DEFVAL { 45 } ::= { atmfAAL2CommonProfileEntry 5 } atmfAAL2SscsMaxSssarSduLength OBJECT-TYPE SYNTAX INTEGER (1..65568) MAX-ACCESS read-only STATUS current DESCRIPTION "This is the maximum size and SSSAR-SDU can take as defined in I.366.1. This parameter only applies to those AAL2 channels using I.366.1 SSSAR. This parameter is bidirectional, i.e its value applies to both directions of the AAL2 connection. Note that if the appID indicates Loop Emulation Service as the AAL2 application then the minimum allowable value of this parameter is 493." ::= { atmfAAL2CommonProfileEntry 6 } atmfAAL2SscsSstedStatus OBJECT-TYPE SYNTAX INTEGER { selected(1), notSelected(2) } MAX-ACCESS read-only STATUS current DESCRIPTION "This specifies whether the SSTED service is used or not. If the value of this object is 'selected' then I.366.1 SSSAR must be supported by the AAL2. This parameter only applies to those AAL2 channels using I.366.1 SSSAR." ::= { atmfAAL2CommonProfileEntry 7 } atmfAAL2SscsSsadtStatus OBJECT-TYPE SYNTAX INTEGER { selected(1), notSelected(2) } MAX-ACCESS read-only STATUS current DESCRIPTION "This specifies whether SSADT service is used or not. Note that if the value of this object is 'selected' then I.366.1 SSSAR must be supported and by implication the SSTED service must also be 'selected'. This parameter only applies to those AAL2 channels using I.366.1 SSSAR." ::= { atmfAAL2CommonProfileEntry 8 } atmfAAL2SscsServiceCategory OBJECT-TYPE SYNTAX INTEGER { audio (1), multirate (2), audioAndMultiRate (3) } MAX-ACCESS read-only STATUS current DESCRIPTION "This object describes the type of service category supported by this AAL2 PVC." DEFVAL { audio } ::= { atmfAAL2CommonProfileEntry 9 } atmfAAL2SscsAudioServiceTransport OBJECT-TYPE SYNTAX INTEGER { disabled (1), enabled (2) } MAX-ACCESS read-only STATUS current DESCRIPTION "This object describes whether the Audio Service that is used for transporting voice and voiceband data is enabled or disabled." DEFVAL { enabled } ::= { atmfAAL2CommonProfileEntry 10 } atmfAAL2SscsProfileSource OBJECT-TYPE SYNTAX INTEGER { itut (1), other (2) } MAX-ACCESS read-only STATUS current DESCRIPTION "This attribute describes the source of the profile. " DEFVAL { itut } ::= { atmfAAL2CommonProfileEntry 11 } atmfAAL2SscsIeeeOui OBJECT-TYPE SYNTAX INTEGER MAX-ACCESS read-only STATUS current DESCRIPTION "This attribute contains the IEEE Organizationally Unique Identifier (OUI) of the organisation that specified the profile being used, if other than ITU-T. For example, if the source is the ATM Forum, the value of this object is 00A03E. This attribute is only meaningful if atmfAAL2SccsProfileSource has the value 'other'." ::= { atmfAAL2CommonProfileEntry 12 } atmfAAL2SscsPredefinedProfileIdentifier OBJECT-TYPE SYNTAX INTEGER MAX-ACCESS read-only STATUS current DESCRIPTION "This object describes the predefined profile identifier." DEFVAL { 1 } ::= { atmfAAL2CommonProfileEntry 13 } atmfAAL2SscsPcmEncoding OBJECT-TYPE SYNTAX INTEGER { aLaw (1), ulaw (2) } MAX-ACCESS read-only STATUS current DESCRIPTION "This object describes the type of PCM encoding used." DEFVAL { aLaw } ::= { atmfAAL2CommonProfileEntry 14 } atmfAAL2SscsFaxDemodulationTransport OBJECT-TYPE SYNTAX INTEGER { disabled (1), enabled (2) } MAX-ACCESS read-only STATUS current DESCRIPTION "This object describes whether transport of demodulated facsimile data is enabled or disabled." DEFVAL { disabled } ::= { atmfAAL2CommonProfileEntry 15 } atmfAAL2SscsCasSignalingTransport OBJECT-TYPE SYNTAX INTEGER { disabled (1), enabled (2) } MAX-ACCESS read-only STATUS current DESCRIPTION "This attribute describes whether transport of CAS signaling bits is enabled or disabled." DEFVAL { disabled } ::= { atmfAAL2CommonProfileEntry 16 } atmfAAL2SscsDtmfDigitPacketTransport OBJECT-TYPE SYNTAX INTEGER { disabled (1), enabled (2) } MAX-ACCESS read-only STATUS current DESCRIPTION "This attribute describes whether transport of DTMF dialled digits is enabled or disabled." DEFVAL { disabled } ::= { atmfAAL2CommonProfileEntry 17 } atmfAAL2SscsMfR1DigitPacketTransport OBJECT-TYPE SYNTAX INTEGER { disabled (1), enabled (2) } MAX-ACCESS read-only STATUS current DESCRIPTION "This object describes whether transport of MF-R1 dialled digits is enabled or disabled." DEFVAL { disabled } ::= { atmfAAL2CommonProfileEntry 18 } atmfAAL2SscsMfR2DigitPacketTransport OBJECT-TYPE SYNTAX INTEGER { disabled (1), enabled (2) } MAX-ACCESS read-only STATUS current DESCRIPTION "This object describes whether transport of MF-R2 dialled digits is enabled or disabled." DEFVAL { disabled } ::= { atmfAAL2CommonProfileEntry 19 } atmfAAL2SscsCircuitModeDataTransport OBJECT-TYPE SYNTAX INTEGER { disabled (1), enabled (2) } MAX-ACCESS read-only STATUS current DESCRIPTION "This object describes whether transport of circuit mode data is enabled or disabled." DEFVAL { disabled } ::= { atmfAAL2CommonProfileEntry 20 } atmfAAL2SscsCircuitModeDataNumChannels OBJECT-TYPE SYNTAX INTEGER (1..31) MAX-ACCESS read-only STATUS current DESCRIPTION "This object describes the multiplier N in N*64kbit/s circuit mode data. It is only applicable if the value of atmfAAL2SscsCircuitModeDataTransport is 'enabled'." DEFVAL { 1 } ::= { atmfAAL2CommonProfileEntry 21 } atmfAAL2SscsFrameModeDataTransport OBJECT-TYPE SYNTAX INTEGER { disabled (1), enabled (2) } MAX-ACCESS read-only STATUS current DESCRIPTION "This object describes whether the I.366.2 frame mode data service is enabled or disabled." DEFVAL { disabled } ::= { atmfAAL2CommonProfileEntry 22 } atmfAAL2SscsFrameModeDataMaxLength OBJECT-TYPE SYNTAX INTEGER (1..65535) MAX-ACCESS read-only STATUS current DESCRIPTION "This object specifies the maximum length of I.366.2 frame mode data. It is only applicable if the value of atmfAAL2FrameModeDataTransport is 'enabled'." ::= { atmfAAL2CommonProfileEntry 23 } atmfAAL2SscopSduLength OBJECT-TYPE SYNTAX INTEGER (1..65524) MAX-ACCESS read-only STATUS current DESCRIPTION "The Maximum SSCOP-SDU length. This object is only required is the value of atmfAAL2SscsSsadtStatus is selected else it is not applicable." ::= { atmfAAL2CommonProfileEntry 24 } atmfAAL2SscopUuFieldLength OBJECT-TYPE SYNTAX INTEGER (1..65524) MAX-ACCESS read-only STATUS current DESCRIPTION "The Maximum SSCOP-UU field length. This object is only required is the value of atmfAAL2SscsSsadtStatus is selected else it is not applicable." ::= { atmfAAL2CommonProfileEntry 25 } ------------------------------------------------------------------ -- ATM Forum ILMI Extension for Auto Configuration -- ATM Trunking AAL2 Profile ------------------------------------------------------------------ atmfAAL2TrunkingProfileTable OBJECT-TYPE SYNTAX SEQUENCE OF AtmfAAL2TrunkingProfileEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "The ATM Forum ILMI Auto Configuration Extension AAL2 Profile Information. This table contains AAL2 parameters that are specific to the ATM Trunking AAL 2 application. These parameters are taken from af-vtoa-0113.000" ::= { atmfAutoConfigGroup 7 } atmfAAL2TrunkingProfileEntry OBJECT-TYPE SYNTAX AtmfAAL2TrunkingProfileEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "An atmfAAL2TrunkingProfileEntry provides AAL2 parameters of operation for ATM Trunking applications to be used in addition to those provided in the Common AAL2 Profile Table. These together provide complete configuration of AAL2 for PVCs that support ATM Trunking using AAl2 as defined in af-vtoa-0113.000." INDEX { atmfAAL2ProfileIndex } ::= { atmfAAL2TrunkingProfileTable 1 } AtmfAAL2TrunkingProfileEntry ::= SEQUENCE { atmfAAL2Vcci INTEGER, atmfAAL2SignalingVcci INTEGER } atmfAAL2Vcci OBJECT-TYPE SYNTAX INTEGER MAX-ACCESS read-only STATUS current DESCRIPTION "This object uniquely identifies a PVC between IWFs." ::= { atmfAAL2TrunkingProfileEntry 1 } atmfAAL2SignalingVcci OBJECT-TYPE SYNTAX INTEGER MAX-ACCESS read-only STATUS current DESCRIPTION "This object specifies the VCCI of the PVC that is used to carry the CCS for this PVC." ::= { atmfAAL2TrunkingProfileEntry 2 } ------------------------------------------------------------------ -- ATM Forum ILMI Extension for Auto Configuration -- ATM LES AAL2 Profile -- In the case where an AAL2LESProfileEntry contains parameter(s) -- which is/are set to a value that is/are not supported by the AAL2 -- entity in the ATU-R, the user-side IME must raise an -- atmfAtmServiceConfFail trap towards the network-side IME. The -- atmfAtmServiceConfFailReason should be 'unsupportedAAL' and -- the atmfAtmServiceConfFailOID must point to the -- atmfAAL2LESProfileEntry that contains the unsupported -- parameter(s). ------------------------------------------------------------------ atmfAAL2LESProfileTable OBJECT-TYPE SYNTAX SEQUENCE OF AtmfAAL2LESProfileEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "The ATM Forum ILMI Auto Configuration Extension AAL2 Profile Information. This table contains AAL2 parameters that are specific to the ATM LES AAL 2 application. These parameters are taken from af-vmna-0145.000" ::= { atmfAutoConfigGroup 8 } atmfAAL2LESProfileEntry OBJECT-TYPE SYNTAX AtmfAAL2LESProfileEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "An atmfAAL2LESProfileEntry provides AAL2 parameters of operation for LES applications to be used in addition to those provided in the Common AAL2 Profile Table. These together provide complete configuration of AAL2 for PVCs that support LES using AAl2 as defined in af-vmoa-0145.000." INDEX { atmfAAL2ProfileIndex } ::= { atmfAAL2LESProfileTable 1 } AtmfAAL2LESProfileEntry ::= SEQUENCE { atmfAAL2CpsCIDLowerLimit INTEGER, atmfAAL2CpsCIDUpperLimit INTEGER, atmfAAL2CpsOptimisation INTEGER } atmfAAL2CpsCIDLowerLimit OBJECT-TYPE SYNTAX INTEGER (16..223) MAX-ACCESS read-only STATUS current DESCRIPTION "The minimum value the CID can take for AAL2 bearer channels and ISDN-D channels." DEFVAL { 16 } ::= { atmfAAL2LESProfileEntry 1 } atmfAAL2CpsCIDUpperLimit OBJECT-TYPE SYNTAX INTEGER (16..223) MAX-ACCESS read-only STATUS current DESCRIPTION " The maximum value the CID can take for AAL2 bearer channels and ISDN-D channels." DEFVAL { 223 } ::= { atmfAAL2LESProfileEntry 2 } atmfAAL2CpsOptimisation OBJECT-TYPE SYNTAX INTEGER { singleCpsPacketPerCpsPduNoOverlap(1), multipleCpsPacketsPerCpsPduWithOverlap(2) } MAX-ACCESS read-only STATUS current DESCRIPTION "This object refers to the mode of operation of the CPS on the CP-IWF The value of this object imposes a restriction on the CPS-SDU length and hence must override the value of atmfAAl2CpsMaxSDULength. singleCpsPacketPerCpsPduNoOverlap -A single CPS Packet is contained within a CPS-PDU and no overlap can occur into the next CPS-PDU. If this option is selected, then Timer_CU is not applicable. Also Max CPS-SDU size must be less than or equal to 44. multipleCpsPacketsPerCpsPduWithOverlap - Multiple CPS Packets are contained within a CPS-PDU and overlap can occur into the next CPS-PDU. If this option is selected, then Timer_CU is applicable. Also Max CPS-SDU size must be less than or equal to 64." DEFVAL { singleCpsPacketPerCpsPduNoOverlap } ::= { atmfAAL2LESProfileEntry 3 } ------------------------------------------------------------------ -- ATM Forum ILMI Extension for Auto Configuration -- atmfAtmServicePhyMacIdentifier ------------------------------------------------------------------ atmfAtmServiceConnInfoExtensionTable OBJECT-TYPE SYNTAX SEQUENCE OF AtmfAtmServiceConnInfoExtensionEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "The ATM Forum ILMI Auto Configuration Extension ATM Service Connection Information. " ::= { atmfAutoConfigGroup 9 } atmfAtmServiceConnInfoExtensionEntry OBJECT-TYPE SYNTAX AtmfAtmServiceConnInfoExtensionEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "An entry in the service connection information extension table provides additional elements that help describe the ATM connection that provides a service across an ATM interface. The connection is identified by port and VPI/VCI value." AUGMENTS { atmfAtmServiceConnInfoEntry } ::= { atmfAtmServiceConnInfoExtensionTable 1 } AtmfAtmServiceConnInfoExtensionEntry ::= SEQUENCE { atmfAtmServicePhyMacIdentifier INTEGER } atmfAtmServicePhyMacIdentifier OBJECT-TYPE SYNTAX INTEGER MAX-ACCESS read-only STATUS current DESCRIPTION " When the physical and/or MAC layer has more than one PHY-connection or MAC-connection, this object is used to select the PHY- or MAC-connection to be bound to the PVC. The semantics of the value of this object is PHY and/or MAC specific. This semantics generally shall be specified with the PHY or MAC. However, the semantics for the two PHY/MAC specifications which have been identified as having multiple connections is provided here for convenience: When the physical layer is dual latency ADSL, the PhyMacIdentifier selects the latency path to be bound to each direction of transmission for the PVC. The value of the PhyMacIdentifier shall be as follows: default = 0 upstream and downstream both interleaved path = 1 upstream and downstream both fast path = 2 upstream interleaved path, downstream fast path = 3 upstream fast path, downstream interleaved path = 4 The 'default' value shall be used for single latency ADSL PHYs. When the physical and MAC layers are IEEE 802.14, the PhyMacIdentifier specifies the 802.14 Local Identifier for the PVC" ::= { atmfAtmServiceConnInfoExtensionEntry 1 } ------------------------------------------------------------------ -- ATM Forum ILMI Extension for Auto Configuration -- Layer 2 and Layer 3 Protocol ID ------------------------------------------------------------------ atmfAtmServiceTypeExtensionTable OBJECT-TYPE SYNTAX SEQUENCE OF AtmfAtmServiceTypeExtensionEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "The ATM Forum ILMI Auto Configuration Extension ATM Service Type Extension Information. " ::= { atmfAutoConfigGroup 10 } atmfAtmServiceTypeExtensionEntry OBJECT-TYPE SYNTAX AtmfAtmServiceTypeExtensionEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "An entry in the service type extension table describes additional information about a service that may be associated with individual ATM connections for the purpose of auto-configuration. This information describes the Client Protocol ID's associated with a particular service." AUGMENTS { atmfAtmServiceTypeEntry } ::= { atmfAtmServiceTypeExtensionTable 1 } AtmfAtmServiceTypeExtensionEntry ::= SEQUENCE { atmfAtmServiceLayer2ProtocolId OCTET STRING, atmfAtmServiceLayer3ProtocolId OCTET STRING } atmfAtmServiceLayer2ProtocolId OBJECT-TYPE SYNTAX OCTET STRING MAX-ACCESS read-only STATUS current DESCRIPTION "This object shall be used to select the user plane layer 2 protocol (if any) to be used above the AAL. The first octet of this object shall be encoded as follows. Bits 5-7 (i.e. the three most significant bits) shall be set to 0; any other values shall be ignored. Bits 0-4 (i.e. the five least significant bits) shall be encoded as shown in the entry for 'User information layer 2 protocol (octet 6)' in Table 4-10/Q.2931. However, if no user plane layer 2 protocol is present above the AAL, then the first (and only) octet shall be encoded as '0b00000000'. If the encoding of the first octet requires subsequent octets, then bit 7 (i.e., the most significant bit) of each of these octets shall be set to 0; however, if it is set to 1, it shall be ignored. Bits 0-6 shall be encoded according to table 4-10/Q.2931. If more than one subsequent octet is needed, then octets shall appear in the order shown in figure 4-16/Q.2931." ::= { atmfAtmServiceTypeExtensionEntry 1 } atmfAtmServiceLayer3ProtocolId OBJECT-TYPE SYNTAX OCTET STRING MAX-ACCESS read-only STATUS current DESCRIPTION "This object shall be used to select a user plane layer 3 protocol (or user plane layer 2 bridging). The first octet of this object shall be encoded as follows. Bits 5-7 (i.e., the three most significant bits) shall be set to 0; any other values shall be ignored. Bits 0-4 (i.e., the five least significant bits) shall be encoded as shown in the entry for 'User information layer 3 protocol (octet 7)' in Table 4-10/Q.2931. However, if no user plane layer 3 protocol is specified, then the first (and only) octet shall be encoded as '0b00000000'. a) If ISO TR9577 network layer protocol identification is to be used, then the first octet shall be encoded to indicate 'ISO/IEC TR9577'. In this case, either: i) the user plane layer 3 protocol is to be selected in the management plane. The second octet of this object shall contain the ISO/IEC TR9577 Initial Protocol Identifier (IPI). - For layer 3 protocols for which ISO/IEC has assigned a Network Layer Protocol Identifier (NLPID), then this NLPID shall be used as the IPI, and the length of the octet string shall be 2. - For layer 3 protocols for which ISO/IEC has not assigned an NLPID, the IPI shall be encoded to indicate 'IEEE 802.1a SNAP identifier' (see Annex D of ISO/IEC 9577). The following five octets (octets 3 through 7) of this object shall then contain a SNAP identifier, which consists of a 3-octet organization unique identifier (OUI) and a 2-octet protocol identifier (PID). This SNAP coding shall be used only if ISO/IEC has not assigned a Network Layer Protocol Identifier for the layer 3 or layer 2 protocol. The octet string shall thus be 7 octets long. - If an IME wishes to indicate that bridged LAN frames are to be carried in the user plane then the IPI shall be encoded to indicate 'IEEE 802.1a SNAP identifier'. The following five octets of this object shall contain a SNAP identifier, which indicates the bridged protocol. For consistency with SIG 4.0, use of the ISO/IEC subsequent protocol identifier (SPI) is not recommended but not explicitly prohibited as one can envision scenarios where it has utility. or ii) the user plane layer 3 protocol is to be selected using network layer protocol identification in the user plane. The octet-string shall be one octet long. The first octet(s) of each layer 3 protocol data unit shall contain layer 3 protocol identification according to ISO/IEC TR9577. b)If bits 0-4 of the first octet of the octet string are set to any value other than 'ISO/IEC TR9577', then any subsequent octets shall be encoded as follows. Bit 7 (i.e., the most significant bit) of each of these octets shall be set to 0; however, if it is set to 1, it shall be ignored. Bits 0-6 shall be encoded according to the codings for octet 7a, octet 7b and octet 7c specified in table 4- 10/Q.2931. If more than one subsequent octet is needed, then octets shall appear in the order shown in figure 4-16/Q.2931." ::= { atmfAtmServiceTypeExtensionEntry 2} ------------------------------------------------------------------ -- ATM Forum ILMI Extension for Auto Configuration -- AAL5 Profile Extension Table -- This extension is required for supporting AAL2 trunking ------------------------------------------------------------------ atmfAAL5ProfileExtensionTable OBJECT-TYPE SYNTAX SEQUENCE OF AtmfAAL5ProfileExtensionEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "Additional parameters for the AAL5 Profile are stored in this table." ::= { atmfAutoConfigGroup 11 } atmfAAL5ProfileExtensionEntry OBJECT-TYPE SYNTAX AtmfAAL5ProfileExtensionEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "An entry in this table augments an entry in the atmfAAL5ProfileTable" AUGMENTS { atmfAAL5ProfileEntry } ::= { atmfAAL5ProfileExtensionTable 1 } AtmfAAL5ProfileExtensionEntry ::= SEQUENCE { atmfAAL5Vcci INTEGER } atmfAAL5Vcci OBJECT-TYPE SYNTAX INTEGER MAX-ACCESS read-only STATUS current DESCRIPTION "This object's value is only applicable if the AAL5 VCC is carrying CCS for AAL2 narrowband calls." ::= { atmfAAL5ProfileExtensionEntry 1 } ------------------------------------------------------------------ -- ATM Forum ILMI Extension for Auto Configuration -- Configuration Failed Trap ------------------------------------------------------------------ atmfAtmServiceConfFail TRAP-TYPE ENTERPRISE atmForum VARIABLES { atmfAtmServiceConfFailReason, atmfAtmServiceConfFailOID } DESCRIPTION "The user-side IME will send this trap whenever it is unable to configure itself based on the information provided in the ILMI auto-configuration MIB. The variables included in the trap identify the reason for the failure and the row in the MIB table that caused the failure. " ::= 3 atmfAtmServiceConfFailReason OBJECT-TYPE SYNTAX INTEGER { unsupportedClientProtocol (1), unsupportedServiceCategory (2), unsupportedAAL (3), invalidVPIVCIValue (4), tooManyPVCs (5), incompleteConfigurationInformation (6), inconsistentConfigurationInformation (7) } MAX-ACCESS read-only STATUS current DESCRIPTION "The reason for the failure to configure the PVC at the ATU-R" ::= { atmfAutoConfigGroup 12 } atmfAtmServiceConfFailOID OBJECT-TYPE SYNTAX RowPointer MAX-ACCESS read-only STATUS current DESCRIPTION "This object holds a pointer to a row in the appropriate table depending on the value of the atmfAtmServiceFailReason object. This will allow the network side to determine MIB information that caused the auto-configuration failure. The value of this object should be as follows: If atmfAtmServiceConfFailReason = 1 or 2, then this object's value points to the row in the atmfAtmServiceTypeTable that is the cause of the problem. If atmfAtmServiceConfFailReason = 3, then this object's value points to the row in the atmfAALxProfileTable, where x is 1, 2, 34, or 5 depending on the AAL that can't be supported. If atmfAtmServiceConfFailReason = 4, then this object's value points to the row in the atmfAtmServiceConnInfoTable that is the cause of the problem. For any other value of atmfAtmServiceConfFailReason, this object's value should be ignored." ::= { atmfAutoConfigGroup 13 } END