-- ************************************************************************ -- APPACCELERATION-STATUS-MIB.txt: Citrix Systems Application Acceleration -- System Status MIB -- -- -- Copyright (c) 2004-2013 by Citrix Systems, Inc. -- All rights reserved. -- -- ************************************************************************ -- APPACCELERATION-STATUS-MIB DEFINITIONS ::= BEGIN IMPORTS MODULE-COMPLIANCE, OBJECT-GROUP FROM SNMPv2-CONF MODULE-IDENTITY, OBJECT-TYPE, Counter64, TimeTicks, IpAddress, Counter, Integer32 FROM SNMPv2-SMI DisplayString FROM SNMPv2-TC InetAddress, InetAddressType, InetAddressPrefixLength FROM INET-ADDRESS-MIB AppAccelerationAlarmSeverity, AppAccelerationSeqNum, AppAccelerationYesNo, AppAccelerationDescription FROM APPACCELERATION-TC appAccelerationMgmt, appAccelerationNotifications FROM APPACCELERATION-SMI; appAccelerationStatusMIB MODULE-IDENTITY LAST-UPDATED "201310110000Z" ORGANIZATION "www.citrix.com" CONTACT-INFO " Citrix Systems, Inc. Postal: 851 West Cypress Creek Road Fort Lauderdale, Florida 33309 United States" DESCRIPTION "This module defines the status variables that can be retrieved from a Citrix Application Acceleration unit. " ::= { appAccelerationMgmt 1 } -- -- Base assignments -- wsStatusMIBObjects OBJECT IDENTIFIER ::= { appAccelerationStatusMIB 1 } wsStatusMIBNotifications OBJECT IDENTIFIER ::= { appAccelerationNotifications 1 } wsStatusMIBConformance OBJECT IDENTIFIER ::= { appAccelerationStatusMIB 2 } -- -- Status Scalars -- wsStatusMIBScalars OBJECT IDENTIFIER ::= { wsStatusMIBObjects 1 } wsOperStatus OBJECT-TYPE SYNTAX INTEGER { active(1), busy(100), down(101), licenseExpired(102), bypassTraffic(103) } MAX-ACCESS read-only STATUS current DESCRIPTION "The current operational state of the unit." ::= { wsStatusMIBScalars 1 } wsLoad1Min OBJECT-TYPE SYNTAX INTEGER MAX-ACCESS read-only STATUS deprecated DESCRIPTION "The 1 minute load average that is also available in the Unix TOP or UPTIME commands. It reports the average number of processes ready to be run. The value is computed by taking the load average value and multiplying it by 100, then converting the value to an integer." ::= { wsStatusMIBScalars 2 } wsLoad5Min OBJECT-TYPE SYNTAX INTEGER MAX-ACCESS read-only STATUS deprecated DESCRIPTION "The 5 minute load average that is also available in the Unix TOP or UPTIME commands. It reports the average number of processes ready to be run. The value is computed by taking the load average value and multiplying it by 100, then converting the value to an integer." ::= { wsStatusMIBScalars 3 } wsLoad15Min OBJECT-TYPE SYNTAX INTEGER MAX-ACCESS read-only STATUS deprecated DESCRIPTION "The 15 minute load average that is also available in the Unix TOP or UPTIME commands. It reports the average number of processes ready to be run. The value is computed by taking the load average value and multiplying it by 100, then converting the value to an integer." ::= { wsStatusMIBScalars 4 } wsBypass OBJECT-TYPE SYNTAX INTEGER { normal(1), bypass(2) } MAX-ACCESS read-only STATUS current DESCRIPTION "Traffic processing status. This is also available in the GUI Features page. " ::= { wsStatusMIBScalars 5 } wsLastAlarmSeqNum OBJECT-TYPE SYNTAX AppAccelerationSeqNum MAX-ACCESS read-only STATUS current DESCRIPTION "The value of the alarm sequence number for the last alarm generated as a trap." ::= { wsStatusMIBScalars 6 } wsBoostStatus OBJECT-TYPE SYNTAX INTEGER { hardboost(1), softboost(2) } MAX-ACCESS read-only STATUS deprecated DESCRIPTION "The selected boost mode. This is also available in the GUI Bandwidth Management page. " ::= { wsStatusMIBScalars 7 } wsBandwidthMode OBJECT-TYPE SYNTAX INTEGER { full(1), partial(2) } MAX-ACCESS read-only STATUS current DESCRIPTION "The selected bandwidth usage. This is also available in the GUI Bandwidth Management page. " ::= { wsStatusMIBScalars 8 } wsBandwidthLimit OBJECT-TYPE SYNTAX INTEGER UNITS "K-Bits/sec" MAX-ACCESS read-only STATUS current DESCRIPTION "Send bandwidth limit. This is also available in the GUI Bandwidth Management page. " ::= { wsStatusMIBScalars 9 } wsWanOutOctets OBJECT-TYPE SYNTAX Counter64 UNITS "Octets" MAX-ACCESS read-only STATUS current DESCRIPTION "Number of accelerated octets transmitted on the WAN side. This is also available in the GUI Usage Graph page. " ::= { wsStatusMIBScalars 10 } wsWanInOctets OBJECT-TYPE SYNTAX Counter64 UNITS "Octets" MAX-ACCESS read-only STATUS current DESCRIPTION "Number of accelerated octets received on the WAN side. This is also available in the GUI Usage Graph page. " ::= { wsStatusMIBScalars 11} wsLanOutOctets OBJECT-TYPE SYNTAX Counter64 UNITS "Octets" MAX-ACCESS read-only STATUS current DESCRIPTION "Number of accelerated octets transmitted on the LAN side. This is also available in the GUI Usage Graph page. " ::= { wsStatusMIBScalars 12} wsLanInOctets OBJECT-TYPE SYNTAX Counter64 UNITS "Octets" MAX-ACCESS read-only STATUS current DESCRIPTION "Number of accelerated octets received on the LAN side. This is also available in the GUI Usage Graph page. " ::= { wsStatusMIBScalars 13} wsCompressionEffectiveBandwidth OBJECT-TYPE SYNTAX INTEGER UNITS "K-Bits/sec" MAX-ACCESS read-only STATUS current DESCRIPTION "The equivalent throughput before compression. This is also available in the GUI Compression Status page. This variable may be reset from the above web page. " ::= { wsStatusMIBScalars 14} wsSendCompressionRatio OBJECT-TYPE SYNTAX INTEGER MAX-ACCESS read-only STATUS current DESCRIPTION "Average send compression rate per 1000 octets, e.g. 3500 means 3.5 to 1 compression. This is also available in the GUI Compression Status page. This variable may be reset from the above web page. " ::= { wsStatusMIBScalars 15} wsReceiveCompressionRatio OBJECT-TYPE SYNTAX INTEGER MAX-ACCESS read-only STATUS current DESCRIPTION "Average receive compression rate per 1000 octets, e.g. 3500 means 3.5 to 1 compression. This is also available in the GUI Compression Status page. This variable may be reset from the above web page. " ::= { wsStatusMIBScalars 16} wsCompressionStatsCollectionTime OBJECT-TYPE SYNTAX TimeTicks MAX-ACCESS read-only STATUS current DESCRIPTION "The number of centiseconds (0.01 seconds) since the start of the compression statistics collection. This is also available in the GUI Compression Status page. This variable may be reset from the above web page. " ::= { wsStatusMIBScalars 17} wsAcceleratedConnections OBJECT-TYPE SYNTAX INTEGER MAX-ACCESS read-only STATUS current DESCRIPTION "Number of current accelerated (active + inactive) connections. This is also available in the GUI System Status page. " ::= { wsStatusMIBScalars 18} wsNonAcceleratedConnections OBJECT-TYPE SYNTAX INTEGER MAX-ACCESS read-only STATUS current DESCRIPTION "Number of current non-accelerated connections. This is also available in the GUI System Status page. " ::= { wsStatusMIBScalars 19} wsHaState OBJECT-TYPE SYNTAX INTEGER { standalone (0), primary (1), secondary (2), restarting (3), starting (4), invalid (5) } MAX-ACCESS read-only STATUS current DESCRIPTION "High availability state of the unit. This is also available in the GUI High Availability page. " ::= { wsStatusMIBScalars 20} wsHaVmIp OBJECT-TYPE SYNTAX IpAddress MAX-ACCESS read-only STATUS current DESCRIPTION "Virtual Management IP Address used in HA setup. This is also available in the GUI High Availability page. " ::= { wsStatusMIBScalars 21} wsHaSecondaryIp OBJECT-TYPE SYNTAX IpAddress MAX-ACCESS read-only STATUS current DESCRIPTION "When retrieved from the primary unit (in HA configuration), this is the IP Address of the secondary unit. When retrieved from a secondary or standalone unit, this is 0.0.0.0. This is also available in the GUI High Availability page. " ::= { wsStatusMIBScalars 22} wsPrimaryIp OBJECT-TYPE SYNTAX IpAddress MAX-ACCESS read-only STATUS current DESCRIPTION "IP Address of the Primary Port, which is for management data. " ::= { wsStatusMIBScalars 23} wsCpuUsage OBJECT-TYPE SYNTAX INTEGER UNITS "%" MAX-ACCESS read-only STATUS current DESCRIPTION "Averaged percent CPU used by the traffic accelerator in the last minute. " ::= { wsStatusMIBScalars 24} wsConnectedPlugIns OBJECT-TYPE SYNTAX Counter MAX-ACCESS read-only STATUS current DESCRIPTION "Current number of Plug-ins connected to this unit. This is also available in the GUI System Status page. " ::= { wsStatusMIBScalars 25 } wsMaxPlugIns OBJECT-TYPE SYNTAX INTEGER MAX-ACCESS read-only STATUS current DESCRIPTION "The Maximum number of Plug-ins that are allowed to connect to this unit. This is also available in the GUI System Status page. " ::= { wsStatusMIBScalars 26 } wsQosStatsCollectionTime OBJECT-TYPE SYNTAX TimeTicks MAX-ACCESS read-only STATUS current DESCRIPTION "The number of centiseconds (0.01 seconds) since the start of the QoS and ICA statistics collection. This is also available in the GUI QoS Statistics page. This variable may be reset from the above web page. " ::= { wsStatusMIBScalars 27} wsUpTime OBJECT-TYPE SYNTAX TimeTicks MAX-ACCESS read-only STATUS current DESCRIPTION "The time (in hundredths of a second) since the unit was last re-initialized. " ::= { wsStatusMIBScalars 28} wsSerialNumber OBJECT-TYPE SYNTAX DisplayString MAX-ACCESS read-only STATUS current DESCRIPTION "Appliance serial number. " ::= { wsStatusMIBScalars 29} wsNonAcceleratedVolume OBJECT-TYPE SYNTAX Counter64 UNITS "1000-Octets" MAX-ACCESS read-only STATUS current DESCRIPTION "Total non-accelerated k-bytes received by the unit, on all interfaces. " ::= { wsStatusMIBScalars 30} wsActiveConnections OBJECT-TYPE SYNTAX INTEGER MAX-ACCESS read-only STATUS current DESCRIPTION "Number of active accelerated connections. This is also available in the GUI System Status page. " ::= { wsStatusMIBScalars 31} wsAccelerationStatus OBJECT-TYPE SYNTAX INTEGER { enabled (1), disabled (2) } MAX-ACCESS read-only STATUS current DESCRIPTION "Traffic acceleration (flow control and compression) status. This is also available in the GUI Features page. " ::= { wsStatusMIBScalars 32} wsTrafficShapingStatus OBJECT-TYPE SYNTAX INTEGER { enabled (1), disabled (2) } MAX-ACCESS read-only STATUS current DESCRIPTION "Traffic shaping (QoS) status. This is also available in the GUI Features page. " ::= { wsStatusMIBScalars 33} wsSystemLoad OBJECT-TYPE SYNTAX INTEGER UNITS "%" MAX-ACCESS read-only STATUS current DESCRIPTION "Load indicator, 100 meant overload. " ::= { wsStatusMIBScalars 34} wsWanSendRate OBJECT-TYPE SYNTAX INTEGER UNITS "bps" MAX-ACCESS read-only STATUS current DESCRIPTION "The average WAN side send rate in the last minute. " ::= { wsStatusMIBScalars 35 } wsWanReceiveRate OBJECT-TYPE SYNTAX INTEGER UNITS "bps" MAX-ACCESS read-only STATUS current DESCRIPTION "The average WAN side receive rate in the last minute. " ::= { wsStatusMIBScalars 36} wsLanSendRate OBJECT-TYPE SYNTAX INTEGER UNITS "bps" MAX-ACCESS read-only STATUS current DESCRIPTION "The average LAN side send rate in the last minute. " ::= { wsStatusMIBScalars 37 } wsLanReceiveRate OBJECT-TYPE SYNTAX INTEGER UNITS "bps" MAX-ACCESS read-only STATUS current DESCRIPTION "The average LAN side receive rate in the last minute. " ::= { wsStatusMIBScalars 38} wsNonAcceleratedRate OBJECT-TYPE SYNTAX INTEGER UNITS "bps" MAX-ACCESS read-only STATUS current DESCRIPTION "The average non-accelerated traffic rate in the last minute. " ::= { wsStatusMIBScalars 39} wsModelNumber OBJECT-TYPE SYNTAX DisplayString MAX-ACCESS read-only STATUS current DESCRIPTION "Appliance model number. " ::= { wsStatusMIBScalars 40} wsWccpStatus OBJECT-TYPE SYNTAX INTEGER { enabled (1), disabled (2) } MAX-ACCESS read-only STATUS current DESCRIPTION "WCCP status. This is also available in the GUI Features page. " ::= { wsStatusMIBScalars 41} -- -- Status Tables -- wsStatusMIBTables OBJECT IDENTIFIER ::= { wsStatusMIBObjects 2 } -- -- Active alarm table -- wsActiveAlarmTable OBJECT-TYPE SYNTAX SEQUENCE OF ActiveAlarmEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "A list of the active alarm entries. This represents the fault conditions that are still active in the unit. " ::= { wsStatusMIBTables 1 } activeAlarmEntry OBJECT-TYPE SYNTAX ActiveAlarmEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "The active alarm entries that are still valid system faults. RFC2578 (SMIv2) requires this to be not-accessible. " INDEX { wsActiveAlarmIndex } ::= { wsActiveAlarmTable 1 } ActiveAlarmEntry ::= SEQUENCE { wsActiveAlarmIndex Integer32, wsActiveAlarmSeqNum AppAccelerationSeqNum, wsActiveAlarmID OBJECT IDENTIFIER, wsActiveAlarmSeverity AppAccelerationAlarmSeverity, wsActiveAlarmLogTime TimeTicks, wsActiveAlarmDesc AppAccelerationDescription, wsActiveAlarmAcked AppAccelerationYesNo, wsActiveAlarmServiceAffect AppAccelerationYesNo } wsActiveAlarmIndex OBJECT-TYPE SYNTAX Integer32 (1..65535) MAX-ACCESS read-only STATUS current DESCRIPTION "An index that uniquely identifies an entry in the active alarm table." ::= { activeAlarmEntry 1 } wsActiveAlarmSeqNum OBJECT-TYPE SYNTAX AppAccelerationSeqNum MAX-ACCESS read-only STATUS current DESCRIPTION "The active alarm's sequence number at the time it was generated." ::= { activeAlarmEntry 2 } wsActiveAlarmID OBJECT-TYPE SYNTAX OBJECT IDENTIFIER MAX-ACCESS read-only STATUS current DESCRIPTION "The OID identifying the actual trap that was generated." ::= { activeAlarmEntry 3 } wsActiveAlarmSeverity OBJECT-TYPE SYNTAX AppAccelerationAlarmSeverity MAX-ACCESS read-only STATUS current DESCRIPTION "The alarm severity for the active alarm." ::= { activeAlarmEntry 4 } wsActiveAlarmLogTime OBJECT-TYPE SYNTAX TimeTicks MAX-ACCESS read-only STATUS current DESCRIPTION "The value of sysUpTime when the alarm was generated." ::= { activeAlarmEntry 5 } wsActiveAlarmDesc OBJECT-TYPE SYNTAX AppAccelerationDescription MAX-ACCESS read-only STATUS current DESCRIPTION "A description for the active alarm." ::= { activeAlarmEntry 6 } wsActiveAlarmAcked OBJECT-TYPE SYNTAX AppAccelerationYesNo MAX-ACCESS read-write STATUS current DESCRIPTION "Identifies if the user has acknowledged the alarm." ::= { activeAlarmEntry 7 } wsActiveAlarmServiceAffect OBJECT-TYPE SYNTAX AppAccelerationYesNo MAX-ACCESS read-only STATUS current DESCRIPTION "Identifies if the alarm is service affecting." ::= { activeAlarmEntry 8 } -- -- Service class statistics table -- wsServiceClassStatsTable OBJECT-TYPE SYNTAX SEQUENCE OF WsServiceClassStatsEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "A list of service class statistics entries. This contains the performance statistics separated by service classes. " ::= { wsStatusMIBTables 2 } wsServiceClassStatsEntry OBJECT-TYPE SYNTAX WsServiceClassStatsEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "Each service class entry contains the performance statistics for one service class. " INDEX { wsServiceClassIndex } ::= { wsServiceClassStatsTable 1 } WsServiceClassStatsEntry ::= SEQUENCE { wsServiceClassIndex INTEGER, wsServiceClassName DisplayString, wsScsCurrentAcceleratedConnections INTEGER, wsScsTotalAcceleratedConnections Counter64, wsScsTotalAcceleratedOctets Counter64, wsScsTotalNonAcceleratedConnections Counter64, wsScsTotalNonAcceleratedOctets Counter64, wsScsTotalPreCompressionOctets Counter64, wsScsCompressSentOctets Counter64, wsScsCompressReceivedOctets Counter64, wsScsPreCompressSentOctets Counter64, wsScsPreCompressReceivedOctets Counter64, wsScsSendBWSavings INTEGER, wsScsRecvBWSavings INTEGER, wsScsSendRecvBWSavings INTEGER, wsScsSendCompressionRatio INTEGER, wsScsRecvCompressionRatio INTEGER, wsScsSendRecvCompressionRatio INTEGER } wsServiceClassIndex OBJECT-TYPE SYNTAX INTEGER(1 .. 2147483647) MAX-ACCESS read-only STATUS current DESCRIPTION "This is used as an index that uniquely identifies a service class in the service class statistics table. " ::= { wsServiceClassStatsEntry 1 } wsServiceClassName OBJECT-TYPE SYNTAX DisplayString MAX-ACCESS read-only STATUS current DESCRIPTION "Name of the service class, e.g. HTTP, FTP, SMTP, CIFS, etc. The list of service classes monitored is defined in the GUI Configure Settings: Service Class page. " ::= { wsServiceClassStatsEntry 2 } wsScsCurrentAcceleratedConnections OBJECT-TYPE SYNTAX INTEGER MAX-ACCESS read-only STATUS current DESCRIPTION "Current number of accelerated connections for the service class. This is also available in the GUI Service Class Statistics Detail page. This counter is reset only on system restart. " ::= { wsServiceClassStatsEntry 3 } wsScsTotalAcceleratedConnections OBJECT-TYPE SYNTAX Counter64 MAX-ACCESS read-only STATUS current DESCRIPTION "Total number of accelerated connections for the service class. This is also available in the GUI Service Class Statistics Detail page. This counter is reset only on system restart. " ::= { wsServiceClassStatsEntry 4 } wsScsTotalAcceleratedOctets OBJECT-TYPE SYNTAX Counter64 UNITS "Octets" MAX-ACCESS read-only STATUS current DESCRIPTION "Total number of accelerated octets for the service class. This is also available in the GUI Service Class Statistics Detail page. This counter is reset only on system restart. " ::= { wsServiceClassStatsEntry 5 } wsScsTotalNonAcceleratedConnections OBJECT-TYPE SYNTAX Counter64 MAX-ACCESS read-only STATUS current DESCRIPTION "Total number of non-accelerated connections for the service class. This is also available in the GUI Service Class Statistics Detail page. This counter is reset only on system restart. " ::= { wsServiceClassStatsEntry 6 } wsScsTotalNonAcceleratedOctets OBJECT-TYPE SYNTAX Counter64 UNITS "Octets" MAX-ACCESS read-only STATUS current DESCRIPTION "Total number of non-accelerated octets for the service class. This is also available in the GUI Service Class Statistics Detail page. This counter is reset only on system restart. " ::= { wsServiceClassStatsEntry 7 } wsScsTotalPreCompressionOctets OBJECT-TYPE SYNTAX Counter64 UNITS "Octets" MAX-ACCESS read-only STATUS current DESCRIPTION "Total number of accelerated octets for the service class before compression. " ::= { wsServiceClassStatsEntry 8 } wsScsCompressSentOctets OBJECT-TYPE SYNTAX Counter64 UNITS "Octets" MAX-ACCESS read-only STATUS current DESCRIPTION "Number of accelerated octets sent for the service class after compression. " ::= { wsServiceClassStatsEntry 9 } wsScsCompressReceivedOctets OBJECT-TYPE SYNTAX Counter64 UNITS "Octets" MAX-ACCESS read-only STATUS current DESCRIPTION "Number of accelerated octets received for the service class after compression. " ::= { wsServiceClassStatsEntry 10 } wsScsPreCompressSentOctets OBJECT-TYPE SYNTAX Counter64 UNITS "Octets" MAX-ACCESS read-only STATUS current DESCRIPTION "Number of accelerated octets sent for the service class before compression. " ::= { wsServiceClassStatsEntry 11 } wsScsPreCompressReceivedOctets OBJECT-TYPE SYNTAX Counter64 UNITS "Octets" MAX-ACCESS read-only STATUS current DESCRIPTION "Number of accelerated octets received for the service class before compression. " ::= { wsServiceClassStatsEntry 12 } wsScsSendBWSavings OBJECT-TYPE SYNTAX INTEGER UNITS "%" MAX-ACCESS read-only STATUS current DESCRIPTION "WAN-side send bandwidth savings. 100% meant very high (above 99.5:1) compression. 0% meant no compression savings. The formula is (Pre-compress-send-bytes - Compressed-send-bytes) / Pre-compress-send-bytes * 100% " ::= { wsServiceClassStatsEntry 13 } wsScsRecvBWSavings OBJECT-TYPE SYNTAX INTEGER UNITS "%" MAX-ACCESS read-only STATUS current DESCRIPTION "WAN-side receive bandwidth savings. 100% meant very high (above 99.5:1) compression. 0% meant no compression savings. The formula is (Pre-compress-received-bytes - Compressed-received-bytes) / Pre-compress-received-bytes * 100% " ::= { wsServiceClassStatsEntry 14 } wsScsSendRecvBWSavings OBJECT-TYPE SYNTAX INTEGER UNITS "%" MAX-ACCESS read-only STATUS current DESCRIPTION "Combined send and receive bandwidth savings. The formula is (Pre-compress-bytes - Compressed-bytes) / Pre-compress-bytes * 100% " ::= { wsServiceClassStatsEntry 15 } wsScsSendCompressionRatio OBJECT-TYPE SYNTAX INTEGER MAX-ACCESS read-only STATUS current DESCRIPTION "WAN-side send compression ratio per 1000 octets, e.g. 3500 means 3.5 to 1 compression. " ::= { wsServiceClassStatsEntry 16 } wsScsRecvCompressionRatio OBJECT-TYPE SYNTAX INTEGER MAX-ACCESS read-only STATUS current DESCRIPTION "WAN-side receive compression ratio per 1000 octets, e.g. 3500 means 3.5 to 1 compression. " ::= { wsServiceClassStatsEntry 17 } wsScsSendRecvCompressionRatio OBJECT-TYPE SYNTAX INTEGER MAX-ACCESS read-only STATUS current DESCRIPTION "Combined send and receive compression ratio per 1000 octets, e.g. 3500 means 3.5 to 1 compression. " ::= { wsServiceClassStatsEntry 18 } -- -- Quality Of Service statistics table -- wsQosTrafficClassStatsTable OBJECT-TYPE SYNTAX SEQUENCE OF WsQosTcStatsEntry MAX-ACCESS not-accessible STATUS deprecated DESCRIPTION "A list of QoS traffic class statistics. " ::= { wsStatusMIBTables 3 } wsQosTcStatsEntry OBJECT-TYPE SYNTAX WsQosTcStatsEntry MAX-ACCESS not-accessible STATUS deprecated DESCRIPTION "Each entry contains performance statistics for one QoS traffic class. " INDEX { wsQosIndex } ::= { wsQosTrafficClassStatsTable 1 } WsQosTcStatsEntry ::= SEQUENCE { wsQosIndex INTEGER, wsQosName DisplayString, wsQosConfiguredSendRatio INTEGER, wsQosSentVolume Counter64, wsQosActualSendRatio INTEGER } wsQosIndex OBJECT-TYPE SYNTAX INTEGER(1 .. 2147483647) MAX-ACCESS read-only STATUS deprecated DESCRIPTION "This index uniquely identifies a QoS traffic class in the QoS traffic class statistics table. " ::= { wsQosTcStatsEntry 1 } wsQosName OBJECT-TYPE SYNTAX DisplayString MAX-ACCESS read-only STATUS deprecated DESCRIPTION "Name of the QoS traffic class, which is defined in the GUI Configure Settings: QoS page. " ::= { wsQosTcStatsEntry 2 } wsQosConfiguredSendRatio OBJECT-TYPE SYNTAX INTEGER UNITS "%" MAX-ACCESS read-only STATUS deprecated DESCRIPTION "The minimum share of the bandwidth configured for this traffic class. This is also available in the GUI QoS Statistics page. " ::= { wsQosTcStatsEntry 3 } wsQosSentVolume OBJECT-TYPE SYNTAX Counter64 UNITS "K-octets" MAX-ACCESS read-only STATUS deprecated DESCRIPTION "The total volume of QoS traffic sent for this queue, measured in 1000-octets. This counter may be reset from the GUI QoS Statistics page. The wsQosStatsCollectionTime variable indicates when the counter was reset. " ::= { wsQosTcStatsEntry 4 } wsQosActualSendRatio OBJECT-TYPE SYNTAX INTEGER UNITS "%" MAX-ACCESS read-only STATUS deprecated DESCRIPTION "The bandwidth used by this traffic class. This is calculated using the wsQosSentVolume for the traffic class divided by the sum of wsQosSentVolume of all traffic classes. " ::= { wsQosTcStatsEntry 5 } -- -- ICA statistics table -- wsIcaStatsTable OBJECT-TYPE SYNTAX SEQUENCE OF WsIcaStatsEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "A list of ICA Traffic Presentation Layer statistics. " ::= { wsStatusMIBTables 4 } wsIcaStatsEntry OBJECT-TYPE SYNTAX WsIcaStatsEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "Each entry contains the performance statistics for one ICA priority. " INDEX { wsIcaIndex } ::= { wsIcaStatsTable 1 } WsIcaStatsEntry ::= SEQUENCE { wsIcaIndex INTEGER, wsIcaServiceName DisplayString, wsIcaPriority INTEGER, wsIcaSentVolume Counter64, wsIcaSentRatio INTEGER, wsIcaReceivedVolume Counter64, wsIcaReceivedRatio INTEGER, wsIcaSendRate INTEGER, wsIcaReceiveRate INTEGER } wsIcaIndex OBJECT-TYPE SYNTAX INTEGER(1 .. 2147483647) MAX-ACCESS read-only STATUS current DESCRIPTION "This is used as an index that uniquely identifies an ICA service in the ICA Traffic Presentation Layer statistics table. " ::= { wsIcaStatsEntry 1 } wsIcaServiceName OBJECT-TYPE SYNTAX DisplayString MAX-ACCESS read-only STATUS current DESCRIPTION "Name of the ICA service, which is also in the GUI QoS Statistics page, Citrix ICA Traffic Presentation Layer Statistics section. " ::= { wsIcaStatsEntry 2 } wsIcaPriority OBJECT-TYPE SYNTAX INTEGER { high(0), medium(1), low(2), background(3), notApplicable(9999) } MAX-ACCESS read-only STATUS deprecated DESCRIPTION "The ICA Priorities: high is for realtime traffic, medium is for interactive traffic, low is for bulk transfer traffic, background is for the lowest priority traffic. This is no longer applicable starting from release 6.0. " ::= { wsIcaStatsEntry 3 } wsIcaSentVolume OBJECT-TYPE SYNTAX Counter64 UNITS "K-octets" MAX-ACCESS read-only STATUS current DESCRIPTION "The total volume of traffic sent for this ICA applications measured in 1000-octets. This counter may be reset from the GUI QoS Statistics page. " ::= { wsIcaStatsEntry 4 } wsIcaSentRatio OBJECT-TYPE SYNTAX INTEGER UNITS "%" MAX-ACCESS read-only STATUS current DESCRIPTION "The sent volume as a percent share of the different ICA applications. " ::= { wsIcaStatsEntry 5 } wsIcaReceivedVolume OBJECT-TYPE SYNTAX Counter64 UNITS "K-octets" MAX-ACCESS read-only STATUS current DESCRIPTION "The total volume of traffic received for this ICA application, measured in 1000-octets. This counter may be reset from the GUI QoS Statistics page. " ::= { wsIcaStatsEntry 6 } wsIcaReceivedRatio OBJECT-TYPE SYNTAX INTEGER UNITS "%" MAX-ACCESS read-only STATUS current DESCRIPTION "The received volume as a percent share of the different priority of the service. This counter may be reset from the GUI QoS Statistics page. " ::= { wsIcaStatsEntry 7 } wsIcaSendRate OBJECT-TYPE SYNTAX INTEGER UNITS "bps" MAX-ACCESS read-only STATUS current DESCRIPTION "The last minute send rate of this ICA application. " ::= { wsIcaStatsEntry 8 } wsIcaReceiveRate OBJECT-TYPE SYNTAX INTEGER UNITS "bps" MAX-ACCESS read-only STATUS current DESCRIPTION "The last minute receive rate of this ICA application. " ::= { wsIcaStatsEntry 9 } -- -- Adapter configuration table -- wsAdapterTable OBJECT-TYPE SYNTAX SEQUENCE OF WsAdapterEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "A list of adapters configured for the unit. It is also in the GUI IP Address page. " ::= { wsStatusMIBTables 5 } wsAdapterEntry OBJECT-TYPE SYNTAX WsAdapterEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "Each entry contains performance statistics for one ADAPTER. " INDEX { wsAdapterIndex } ::= { wsAdapterTable 1 } WsAdapterEntry ::= SEQUENCE { wsAdapterIndex INTEGER, wsAdapterName DisplayString, wsAdapterEnabled INTEGER, wsAdapterIp IpAddress, wsAdapterNetmask IpAddress, wsAdapterGateway IpAddress, wsAdapterVirtualIp IpAddress, wsAdapterVLanEnabled INTEGER, wsAdapterVLanGroup INTEGER } wsAdapterIndex OBJECT-TYPE SYNTAX INTEGER(1 .. 2147483647) MAX-ACCESS read-only STATUS current DESCRIPTION "This is used as an index that uniquely identifies an adapter. " ::= { wsAdapterEntry 1 } wsAdapterName OBJECT-TYPE SYNTAX DisplayString MAX-ACCESS read-only STATUS current DESCRIPTION "Adapter name. " ::= { wsAdapterEntry 2 } wsAdapterEnabled OBJECT-TYPE SYNTAX INTEGER { enabled(1), disabled(2) } MAX-ACCESS read-only STATUS current DESCRIPTION "Adapter state. " ::= { wsAdapterEntry 3 } wsAdapterIp OBJECT-TYPE SYNTAX IpAddress MAX-ACCESS read-only STATUS current DESCRIPTION "Adapter IP address. " ::= { wsAdapterEntry 4 } wsAdapterNetmask OBJECT-TYPE SYNTAX IpAddress MAX-ACCESS read-only STATUS current DESCRIPTION "Adapter network mask. " ::= { wsAdapterEntry 5 } wsAdapterGateway OBJECT-TYPE SYNTAX IpAddress MAX-ACCESS read-only STATUS current DESCRIPTION "Adapter gateway. " ::= { wsAdapterEntry 6 } wsAdapterVirtualIp OBJECT-TYPE SYNTAX IpAddress MAX-ACCESS read-only STATUS current DESCRIPTION " HA virtual IP address. " ::= { wsAdapterEntry 7 } wsAdapterVLanEnabled OBJECT-TYPE SYNTAX INTEGER { enabled(1), disabled(2) } MAX-ACCESS read-only STATUS current DESCRIPTION " VLAN state. " ::= { wsAdapterEntry 8 } wsAdapterVLanGroup OBJECT-TYPE SYNTAX INTEGER MAX-ACCESS read-only STATUS current DESCRIPTION " VLAN group ID. " ::= { wsAdapterEntry 9 } -- -- Link statistics table -- wsLinkStatsTable OBJECT-TYPE SYNTAX SEQUENCE OF LinkStatsEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "A list of link statistics. " ::= { wsStatusMIBTables 6 } linkStatsEntry OBJECT-TYPE SYNTAX LinkStatsEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "Each entry contains the performance statistics for one link. " INDEX { linkIndex } ::= { wsLinkStatsTable 1 } LinkStatsEntry ::= SEQUENCE { linkIndex INTEGER, linkName DisplayString, linkSentVolume Counter64, linkReceivedVolume Counter64, linkSentPackets Counter64, linkReceivedPackets Counter64, linkDroppedSentVolume Counter64, linkDroppedReceivedVolume Counter64, linkDroppedSentPackets Counter64, linkDroppedReceivedPackets Counter64 } linkIndex OBJECT-TYPE SYNTAX INTEGER(1 .. 2147483647) MAX-ACCESS read-only STATUS current DESCRIPTION "This index uniquely identifies a link in the link statistics table. " ::= { linkStatsEntry 1 } linkName OBJECT-TYPE SYNTAX DisplayString MAX-ACCESS read-only STATUS current DESCRIPTION "Name of the link. " ::= { linkStatsEntry 2 } linkSentVolume OBJECT-TYPE SYNTAX Counter64 UNITS "K-octets" MAX-ACCESS read-only STATUS current DESCRIPTION "The total volume of traffic sent on the link, measured in 1000-octets. " ::= { linkStatsEntry 3 } linkReceivedVolume OBJECT-TYPE SYNTAX Counter64 UNITS "K-octets" MAX-ACCESS read-only STATUS current DESCRIPTION "The total volume of traffic received on the link, measured in 1000-octets. " ::= { linkStatsEntry 4 } linkSentPackets OBJECT-TYPE SYNTAX Counter64 UNITS "Packets" MAX-ACCESS read-only STATUS current DESCRIPTION "The total number of packets sent on the link. " ::= { linkStatsEntry 5 } linkReceivedPackets OBJECT-TYPE SYNTAX Counter64 UNITS "Packets" MAX-ACCESS read-only STATUS current DESCRIPTION "The total number of packets received on the link. in 1000-octets. " ::= { linkStatsEntry 6 } linkDroppedSentVolume OBJECT-TYPE SYNTAX Counter64 UNITS "K-octets" MAX-ACCESS read-only STATUS current DESCRIPTION "The total traffic not sent on the link due to QoS threshold, measured in 1000-octets. " ::= { linkStatsEntry 7 } linkDroppedReceivedVolume OBJECT-TYPE SYNTAX Counter64 UNITS "K-octets" MAX-ACCESS read-only STATUS current DESCRIPTION "The total received traffic dropped from the link due to QoS threshold, measured in 1000-octets. " ::= { linkStatsEntry 8 } linkDroppedSentPackets OBJECT-TYPE SYNTAX Counter64 UNITS "Packets" MAX-ACCESS read-only STATUS current DESCRIPTION "The total number of packets not sent on the link due to QoS threshold. " ::= { linkStatsEntry 9 } linkDroppedReceivedPackets OBJECT-TYPE SYNTAX Counter64 UNITS "Packets" MAX-ACCESS read-only STATUS current DESCRIPTION "The total number of received packets dropped from the link due to QoS threshold. " ::= { linkStatsEntry 10 } -- -- Application statistics table -- wsAppStatsTable OBJECT-TYPE SYNTAX SEQUENCE OF AppStatsEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "A list of link statistics. " ::= { wsStatusMIBTables 7 } appStatsEntry OBJECT-TYPE SYNTAX AppStatsEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "Each entry contains the performance statistics for one application on one link. " INDEX { appIndex } ::= { wsAppStatsTable 1 } AppStatsEntry ::= SEQUENCE { appIndex INTEGER, appName DisplayString, appId INTEGER, appParentId INTEGER, appGroupId INTEGER, appSentVolume Counter64, appReceivedVolume Counter64, appSentPackets Counter64, appReceivedPackets Counter64, appDroppedSentVolume Counter64, appDroppedReceiveVolume Counter64, appDroppedSentPackets Counter64, appDroppedReceivedPackets Counter64, appSendRate INTEGER, appReceiveRate INTEGER } appIndex OBJECT-TYPE SYNTAX INTEGER(1 .. 2147483647) MAX-ACCESS read-only STATUS current DESCRIPTION "This index uniquely identifies one application on a link. " ::= { appStatsEntry 1 } appName OBJECT-TYPE SYNTAX DisplayString MAX-ACCESS read-only STATUS current DESCRIPTION "Name of the link. " ::= { appStatsEntry 2 } appId OBJECT-TYPE SYNTAX INTEGER MAX-ACCESS read-only STATUS current DESCRIPTION "Unique ID for application. " ::= { appStatsEntry 3 } appParentId OBJECT-TYPE SYNTAX INTEGER MAX-ACCESS read-only STATUS current DESCRIPTION "Parent application ID. " ::= { appStatsEntry 4 } appGroupId OBJECT-TYPE SYNTAX INTEGER MAX-ACCESS read-only STATUS current DESCRIPTION "Bit mask, indicating the group which this application belong to. " ::= { appStatsEntry 5 } appSentVolume OBJECT-TYPE SYNTAX Counter64 UNITS "K-octets" MAX-ACCESS read-only STATUS current DESCRIPTION "The total volume of traffic sent on the link, measured in 1000-octets. " ::= { appStatsEntry 6 } appReceivedVolume OBJECT-TYPE SYNTAX Counter64 UNITS "K-octets" MAX-ACCESS read-only STATUS current DESCRIPTION "The total volume of traffic sent on the link, measured in 1000-octets. " ::= { appStatsEntry 7 } appSentPackets OBJECT-TYPE SYNTAX Counter64 UNITS "Packets" MAX-ACCESS read-only STATUS current DESCRIPTION "The total volume of traffic sent on the link, measured in 1000-octets. " ::= { appStatsEntry 8 } appReceivedPackets OBJECT-TYPE SYNTAX Counter64 UNITS "Packets" MAX-ACCESS read-only STATUS current DESCRIPTION "The total volume of traffic sent on the link, in 1000-octets. " ::= { appStatsEntry 9 } appDroppedSentVolume OBJECT-TYPE SYNTAX Counter64 UNITS "K-octets" MAX-ACCESS read-only STATUS current DESCRIPTION "The total traffic not sent on the link due to QoS threshold, in 1000-octets. " ::= { appStatsEntry 10 } appDroppedReceiveVolume OBJECT-TYPE SYNTAX Counter64 UNITS "K-octets" MAX-ACCESS read-only STATUS current DESCRIPTION "The total received traffic dropped from the link due to QoS threshold, in 1000-octets. " ::= { appStatsEntry 11 } appDroppedSentPackets OBJECT-TYPE SYNTAX Counter64 UNITS "Packets" MAX-ACCESS read-only STATUS current DESCRIPTION "The total number of packets not sent on the link due to QoS threshold. " ::= { appStatsEntry 12 } appDroppedReceivedPackets OBJECT-TYPE SYNTAX Counter64 UNITS "Packets" MAX-ACCESS read-only STATUS current DESCRIPTION "The total number of received packets dropped from the link due to QoS threshold. " ::= { appStatsEntry 13 } appSendRate OBJECT-TYPE SYNTAX INTEGER UNITS "bps" MAX-ACCESS read-only STATUS current DESCRIPTION "The last minute send rate of this application. " ::= { appStatsEntry 14 } appReceiveRate OBJECT-TYPE SYNTAX INTEGER UNITS "bps" MAX-ACCESS read-only STATUS current DESCRIPTION "The last minute receive rate of this application. " ::= { appStatsEntry 15 } -- -- Link level quality of service statistics table -- wsQosStatsTable OBJECT-TYPE SYNTAX SEQUENCE OF QosStatsEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "A list of QoS traffic class statistics. " ::= { wsStatusMIBTables 8 } qosStatsEntry OBJECT-TYPE SYNTAX QosStatsEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "Each entry contains the performance statistics for one QoS traffic class. " INDEX { qosIndex } ::= { wsQosStatsTable 1 } QosStatsEntry ::= SEQUENCE { qosIndex INTEGER, qosPolicyName DisplayString, qosLink DisplayString, qosSentVolume Counter64, qosReceiveVolume Counter64, qosSentPackets Counter64, qosReceivedPackets Counter64, qosDroppedSentVolume Counter64, qosDroppedReceiveVolume Counter64, qosDroppedSentPackets Counter64, qosDroppedReceivedPackets Counter64 } qosIndex OBJECT-TYPE SYNTAX INTEGER(1 .. 2147483647) MAX-ACCESS read-only STATUS current DESCRIPTION "This index uniquely identifies a QoS traffic class in the QoS traffic class statistics table. " ::= { qosStatsEntry 1 } qosPolicyName OBJECT-TYPE SYNTAX DisplayString MAX-ACCESS read-only STATUS current DESCRIPTION "Name of the QoS Policy. " ::= { qosStatsEntry 2 } qosLink OBJECT-TYPE SYNTAX DisplayString MAX-ACCESS read-only STATUS current DESCRIPTION "Name of the link. " ::= { qosStatsEntry 3 } qosSentVolume OBJECT-TYPE SYNTAX Counter64 UNITS "K-octets" MAX-ACCESS read-only STATUS current DESCRIPTION "The total volume of traffic sent on the link, measured in 1000-octets. " ::= { qosStatsEntry 4 } qosReceiveVolume OBJECT-TYPE SYNTAX Counter64 UNITS "K-octets" MAX-ACCESS read-only STATUS current DESCRIPTION "The total volume of traffic sent on the link, measured in 1000-octets. " ::= { qosStatsEntry 5 } qosSentPackets OBJECT-TYPE SYNTAX Counter64 UNITS "Packets" MAX-ACCESS read-only STATUS current DESCRIPTION "The total volume of traffic sent on the link, measured in 1000-octets. " ::= { qosStatsEntry 6 } qosReceivedPackets OBJECT-TYPE SYNTAX Counter64 UNITS "Packets" MAX-ACCESS read-only STATUS current DESCRIPTION "The total volume of traffic sent on the link, in 1000-octets. " ::= { qosStatsEntry 7 } qosDroppedSentVolume OBJECT-TYPE SYNTAX Counter64 UNITS "K-octets" MAX-ACCESS read-only STATUS current DESCRIPTION "The total traffic not sent on the link due to QoS threshold, in 1000-octets. " ::= { qosStatsEntry 8 } qosDroppedReceiveVolume OBJECT-TYPE SYNTAX Counter64 UNITS "K-octets" MAX-ACCESS read-only STATUS current DESCRIPTION "The total received traffic dropped from the link due to QoS threshold, in 1000-octets. " ::= { qosStatsEntry 9 } qosDroppedSentPackets OBJECT-TYPE SYNTAX Counter64 UNITS "Packets" MAX-ACCESS read-only STATUS current DESCRIPTION "The total number of packets not sent on the link due to QoS threshold. " ::= { qosStatsEntry 10 } qosDroppedReceivedPackets OBJECT-TYPE SYNTAX Counter64 UNITS "Packets" MAX-ACCESS read-only STATUS current DESCRIPTION "The total number of received packets dropped from the link due to QoS threshold. " ::= { qosStatsEntry 11 } -- -- Link level service class statistics table -- wsLscStatsTable OBJECT-TYPE SYNTAX SEQUENCE OF LscStatsEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "A list of link level service class statistics. " ::= { wsStatusMIBTables 9 } lscStatsEntry OBJECT-TYPE SYNTAX LscStatsEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "Each entry contains the performance statistics for one link level service class. " INDEX { lscIndex } ::= { wsLscStatsTable 1 } LscStatsEntry ::= SEQUENCE { lscIndex INTEGER, lscServiceClassName DisplayString, lscLink DisplayString, lscSentVolume Counter64, lscReceivedVolume Counter64, lscSentPackets Counter64, lscReceivedPackets Counter64, lscDroppedSentVolume Counter64, lscDroppedReceiveVolume Counter64, lscDroppedSentPackets Counter64, lscDroppedReceivedPackets Counter64 } lscIndex OBJECT-TYPE SYNTAX INTEGER(1 .. 2147483647) MAX-ACCESS read-only STATUS current DESCRIPTION "This index is used to identify the link statistics within a service class. " ::= { lscStatsEntry 1 } lscServiceClassName OBJECT-TYPE SYNTAX DisplayString MAX-ACCESS read-only STATUS current DESCRIPTION "Name of the service class, e.g. HTTP, FTP, SMTP, CIFS, etc. The list of service classes monitored is defined in the GUI Configure Settings: Service Class page. " ::= { lscStatsEntry 2 } lscLink OBJECT-TYPE SYNTAX DisplayString MAX-ACCESS read-only STATUS current DESCRIPTION "Name of the link. " ::= { lscStatsEntry 3 } lscSentVolume OBJECT-TYPE SYNTAX Counter64 UNITS "K-octets" MAX-ACCESS read-only STATUS current DESCRIPTION "The total volume of traffic sent on the link, measured in 1000-octets. " ::= { lscStatsEntry 4 } lscReceivedVolume OBJECT-TYPE SYNTAX Counter64 UNITS "K-octets" MAX-ACCESS read-only STATUS current DESCRIPTION "The total volume of traffic sent on the link, measured in 1000-octets. " ::= { lscStatsEntry 5 } lscSentPackets OBJECT-TYPE SYNTAX Counter64 UNITS "Packets" MAX-ACCESS read-only STATUS current DESCRIPTION "The total volume of traffic sent on the link, measured in 1000-octets. " ::= { lscStatsEntry 6 } lscReceivedPackets OBJECT-TYPE SYNTAX Counter64 UNITS "Packets" MAX-ACCESS read-only STATUS current DESCRIPTION "The total volume of traffic sent on the link, in 1000-octets. " ::= { lscStatsEntry 7 } lscDroppedSentVolume OBJECT-TYPE SYNTAX Counter64 UNITS "K-octets" MAX-ACCESS read-only STATUS current DESCRIPTION "The total traffic not sent on the link due to QoS threshold, in 1000-octets. " ::= { lscStatsEntry 8 } lscDroppedReceiveVolume OBJECT-TYPE SYNTAX Counter64 UNITS "K-octets" MAX-ACCESS read-only STATUS current DESCRIPTION "The total received traffic dropped from the link due to QoS threshold, in 1000-octets. " ::= { lscStatsEntry 9 } lscDroppedSentPackets OBJECT-TYPE SYNTAX Counter64 UNITS "Packets" MAX-ACCESS read-only STATUS current DESCRIPTION "The total number of packets not sent on the link due to QoS threshold. " ::= { lscStatsEntry 10 } lscDroppedReceivedPackets OBJECT-TYPE SYNTAX Counter64 UNITS "Packets" MAX-ACCESS read-only STATUS current DESCRIPTION "The total number of received packets dropped from the link due to QoS threshold. " ::= { lscStatsEntry 11 } -- -- Repeater partner table -- wsPartnerTable OBJECT-TYPE SYNTAX SEQUENCE OF PartnerEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "A list of CloudBridge partners " ::= { wsStatusMIBTables 10 } partnerEntry OBJECT-TYPE SYNTAX PartnerEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "Each row contains information on one partner unit." INDEX { partnerAddrType, partnerAddr } ::= { wsPartnerTable 1 } PartnerEntry ::= SEQUENCE { partnerAddrType InetAddressType, partnerAddr InetAddress, partnerConnections INTEGER, partnerSendRate INTEGER, partnerReceiveRate INTEGER, partnerIdleTime TimeTicks } partnerAddrType OBJECT-TYPE SYNTAX InetAddressType MAX-ACCESS read-only STATUS current DESCRIPTION "Format of partnerAddr, IPv4 or IPv6. See RFC4001 for InetAddressType and InetAddress usage. " ::= { partnerEntry 1} partnerAddr OBJECT-TYPE SYNTAX InetAddress MAX-ACCESS read-only STATUS current DESCRIPTION "Partner IP address." ::= { partnerEntry 2} partnerConnections OBJECT-TYPE SYNTAX INTEGER MAX-ACCESS read-only STATUS current DESCRIPTION "Number of accelerated connections to partner." ::= { partnerEntry 3} partnerSendRate OBJECT-TYPE SYNTAX INTEGER UNITS "bps" MAX-ACCESS read-only STATUS current DESCRIPTION "The last minute send rate to partner." ::= { partnerEntry 4} partnerReceiveRate OBJECT-TYPE SYNTAX INTEGER UNITS "bps" MAX-ACCESS read-only STATUS current DESCRIPTION "The last minute receive rate from partner." ::= { partnerEntry 5} partnerIdleTime OBJECT-TYPE SYNTAX TimeTicks MAX-ACCESS read-only STATUS current DESCRIPTION "Time where no traffic flows between this partner." ::= { partnerEntry 6} -- -- Notifications -- wsHAMasterIpAddr OBJECT-TYPE SYNTAX IpAddress MAX-ACCESS accessible-for-notify STATUS current DESCRIPTION "The master router's real (primary) IP address. This is the IP address listed as the source in VRRP advertisement last received by this virtual router." ::= { wsStatusMIBObjects 3 } wsSourceIpAddr OBJECT-TYPE SYNTAX IpAddress MAX-ACCESS accessible-for-notify STATUS current DESCRIPTION " The IP address of the source of Alert. " ::= { wsStatusMIBObjects 5 } wsStatusMIBAlertTables OBJECT IDENTIFIER ::= { wsStatusMIBObjects 4 } wsAlertAction OBJECT-TYPE SYNTAX INTEGER { oneShot(0), set(1), reset(2), expired(3) } MAX-ACCESS read-only STATUS current DESCRIPTION "Action of the alert." ::= { wsStatusMIBAlertTables 1 } wsAlertClass OBJECT-TYPE SYNTAX INTEGER { slowLossRate(0), fastLossRate(1), connectionStalled(2), connectionTimeout(3), connectionInvalid(4), nicHalfDuplex(5), arpTimeout(6), badLicense(7), limitExceeded(8), asymmetric(9), badPackets(10), lowOnCpu(11), lowOnMemory(12), internal(13), restartRequired(14), vridNotSet(15), haConfigurationChanged(16), haNoSecondary(17), haPairCommError(18), haNotCapable(19), haPeerVersion(20), compressionError(21), bwTypeMismatch(22), cpuPegged(23), lowOnVm(24), numSlowRtosExceeded(25), numFastRtosExceeded(26), numBootoutsExceeded(27), numRewindsExceeded(28), diskDriveFailing(29), diskDriveDegraded(30), diskDriveFailed(31), groupModeError(32), nicBypassEvent(33), haMisMatchVmip(34), diskFragmented(35), redirectorModeSyn(36), unreachable(37), dnsLookup(38), redirectorModeFailure(39), applianceInTheMiddle(40), internalCritical(41), internalMajor(42), internalMinor(43), internalWarning(44), wccpMajor(45), wccpMinor(46), wccpWarning(47), driverHung(48), signalingChannelError(49), scpsError(50), plugInNearLimit(51), sslError(52), haDispositionError(53), haVIPNotSet(54), vlanNotSupported(55), tooManyBadTcpChecksum(56), invalidGateway(57), haPeerKeyStoreLocked(58), sslProxyMajor(59), sslProxyMinor(60), sslProxyWarning(61), sslTunnelMajor(62), sslTunnelMinor(63), sslTunnelWarning(64), excessiveIpFragments(65), userAccountLocked(66), smb2AccelerationFailure(67), invalidBridgeConfig(68), invalidHttpCachingConfigFile(69), qosEngineError(70), mapiNtlmError(71), ethernetCrcError(72), qosLinkConfigError(73), maxUnacceleratedConnectionsExceeded(74), badHardware(75) } MAX-ACCESS read-only STATUS current DESCRIPTION "Class of the alert." ::= { wsStatusMIBAlertTables 2 } wsAlertMsg OBJECT-TYPE SYNTAX AppAccelerationDescription MAX-ACCESS read-only STATUS current DESCRIPTION "Message of the alert." ::= { wsStatusMIBAlertTables 3 } wsNotifyStart NOTIFICATION-TYPE OBJECTS { wsActiveAlarmSeverity, wsActiveAlarmSeqNum, wsActiveAlarmDesc, wsActiveAlarmServiceAffect, wsPrimaryIp } STATUS current DESCRIPTION "An indication that the agent has started running." ::= { wsStatusMIBNotifications 1 } wsNotifyShutdown NOTIFICATION-TYPE OBJECTS { wsActiveAlarmSeverity, wsActiveAlarmSeqNum, wsActiveAlarmDesc, wsActiveAlarmServiceAffect, wsPrimaryIp } STATUS current DESCRIPTION "An indication that the agent is in the process of being shutdown." ::= { wsStatusMIBNotifications 2 } wsNotifyRestart NOTIFICATION-TYPE OBJECTS { wsActiveAlarmSeverity, wsActiveAlarmSeqNum, wsActiveAlarmDesc, wsActiveAlarmServiceAffect } STATUS deprecated DESCRIPTION "An indication that the agent has been restarted." ::= { wsStatusMIBNotifications 3 } wsHANotifyNewMaster NOTIFICATION-TYPE OBJECTS { wsActiveAlarmSeverity, wsActiveAlarmSeqNum, wsActiveAlarmDesc, wsActiveAlarmServiceAffect, wsHAMasterIpAddr, wsPrimaryIp } STATUS current DESCRIPTION "The newMaster trap indicates that the sending agent has transitioned to 'Master' state." ::= { wsStatusMIBNotifications 4 } wsNotifyAvailBWChange NOTIFICATION-TYPE OBJECTS { wsActiveAlarmSeverity, wsActiveAlarmSeqNum, wsActiveAlarmDesc, wsActiveAlarmServiceAffect } STATUS deprecated DESCRIPTION "And indication that available BW Has Changed" ::= { wsStatusMIBNotifications 5 } wsNotifyUnexpectedRestart NOTIFICATION-TYPE OBJECTS { wsActiveAlarmSeverity, wsActiveAlarmSeqNum, wsActiveAlarmDesc, wsActiveAlarmServiceAffect, wsPrimaryIp } STATUS current DESCRIPTION "An indication that the agent has been unexpectedly restarted." ::= { wsStatusMIBNotifications 6 } wsNotifyPersistentError NOTIFICATION-TYPE OBJECTS { wsActiveAlarmSeverity, wsActiveAlarmSeqNum, wsActiveAlarmDesc, wsActiveAlarmServiceAffect, wsPrimaryIp } STATUS current DESCRIPTION "The unit is experiencing a persistent internal error." ::= { wsStatusMIBNotifications 7 } wsNotifyAlert NOTIFICATION-TYPE OBJECTS { wsActiveAlarmSeverity, wsActiveAlarmSeqNum, wsActiveAlarmDesc, wsActiveAlarmServiceAffect, wsAlertAction, wsAlertClass, wsAlertMsg, wsPrimaryIp } STATUS current DESCRIPTION "An alert is generated from the unit." ::= { wsStatusMIBNotifications 8 } wsNotifyConfigurationChanged NOTIFICATION-TYPE OBJECTS { wsActiveAlarmSeverity, wsActiveAlarmSeqNum, wsActiveAlarmDesc, wsActiveAlarmServiceAffect, wsPrimaryIp } STATUS current DESCRIPTION "An indication that the configuration has changed." ::= { wsStatusMIBNotifications 9 } -- -- Conformance information -- wsStatusMIBCompliances OBJECT IDENTIFIER ::= { wsStatusMIBConformance 1 } wsStatusMIBGroups OBJECT IDENTIFIER ::= { wsStatusMIBConformance 2 } -- Compliance statements wsStatusCompliance MODULE-COMPLIANCE STATUS current DESCRIPTION "The compliance statement for agents which implement appAccelerationStatusMIB. " MODULE MANDATORY-GROUPS { wsStatusGroup, wsStatusTrapGroup, wsStatusNotifyGroup } ::= { wsStatusMIBCompliances 1 } -- -- Units of conformance -- wsStatusGroup OBJECT-GROUP OBJECTS { wsOperStatus, wsLoad1Min, wsLoad5Min, wsLoad15Min, wsBypass, wsLastAlarmSeqNum, wsBoostStatus, wsBandwidthMode, wsBandwidthLimit, wsWanOutOctets, wsWanInOctets, wsLanOutOctets, wsLanInOctets, wsCompressionEffectiveBandwidth, wsSendCompressionRatio, wsReceiveCompressionRatio, wsCompressionStatsCollectionTime, wsAcceleratedConnections, wsNonAcceleratedConnections, wsHaState, wsHaVmIp, wsHaSecondaryIp, wsPrimaryIp, wsCpuUsage, wsConnectedPlugIns, wsMaxPlugIns, wsQosStatsCollectionTime, wsUpTime, wsSerialNumber, wsNonAcceleratedVolume, wsActiveConnections, wsAccelerationStatus, wsTrafficShapingStatus, wsSystemLoad, wsWanSendRate, wsWanReceiveRate, wsLanSendRate, wsLanReceiveRate, wsNonAcceleratedRate, wsModelNumber, wsWccpStatus, wsActiveAlarmIndex, wsActiveAlarmSeqNum, wsActiveAlarmID, wsActiveAlarmSeverity, wsActiveAlarmLogTime, wsActiveAlarmDesc, wsActiveAlarmAcked, wsActiveAlarmServiceAffect, wsServiceClassIndex, wsServiceClassName, wsScsCurrentAcceleratedConnections, wsScsTotalAcceleratedConnections, wsScsTotalAcceleratedOctets, wsScsTotalNonAcceleratedConnections, wsScsTotalNonAcceleratedOctets, wsScsTotalPreCompressionOctets, wsScsCompressSentOctets, wsScsCompressReceivedOctets, wsScsPreCompressSentOctets, wsScsPreCompressReceivedOctets, wsScsSendBWSavings, wsScsRecvBWSavings, wsScsSendRecvBWSavings, wsScsSendCompressionRatio, wsScsRecvCompressionRatio, wsScsSendRecvCompressionRatio, wsQosIndex, wsQosName, wsQosConfiguredSendRatio, wsQosSentVolume, wsQosActualSendRatio, wsIcaIndex, wsIcaServiceName, wsIcaPriority, wsIcaSentVolume, wsIcaSentRatio, wsIcaReceivedVolume, wsIcaReceivedRatio, wsIcaSendRate, wsIcaReceiveRate, wsAdapterIndex, wsAdapterName, wsAdapterEnabled, wsAdapterIp, wsAdapterNetmask, wsAdapterGateway, wsAdapterVirtualIp, wsAdapterVLanEnabled, wsAdapterVLanGroup, linkIndex, linkName, linkSentVolume, linkReceivedVolume, linkSentPackets, linkReceivedPackets, linkDroppedSentVolume, linkDroppedReceivedVolume, linkDroppedSentPackets, linkDroppedReceivedPackets, appIndex, appName, appId, appParentId, appGroupId, appSentVolume, appReceivedVolume, appSentPackets, appReceivedPackets, appDroppedSentVolume, appDroppedReceiveVolume, appDroppedSentPackets, appDroppedReceivedPackets, appSendRate, appReceiveRate, qosIndex, qosPolicyName, qosLink, qosSentVolume, qosReceiveVolume, qosSentPackets, qosReceivedPackets, qosDroppedSentVolume, qosDroppedReceiveVolume, qosDroppedSentPackets, qosDroppedReceivedPackets, lscIndex, lscServiceClassName, lscLink, lscSentVolume, lscReceivedVolume, lscSentPackets, lscReceivedPackets, lscDroppedSentVolume, lscDroppedReceiveVolume, lscDroppedSentPackets, lscDroppedReceivedPackets, partnerAddrType, partnerAddr, partnerConnections, partnerSendRate, partnerReceiveRate, partnerIdleTime } STATUS current DESCRIPTION "A collection of objects used to retrieve status information " ::= { wsStatusMIBGroups 1 } wsStatusTrapGroup OBJECT-GROUP OBJECTS { wsHAMasterIpAddr, wsAlertAction, wsAlertClass, wsAlertMsg } STATUS current DESCRIPTION "Conformance group for objects contained in VRRP notifications." ::= { wsStatusMIBGroups 2 } wsStatusNotifyGroup OBJECT-GROUP OBJECTS { wsNotifyStart, wsNotifyShutdown, wsNotifyRestart, wsHANotifyNewMaster, wsNotifyAvailBWChange, wsNotifyUnexpectedRestart, wsNotifyPersistentError, wsNotifyAlert } STATUS current DESCRIPTION "A collection of the Notifications supported in the status MIB." ::= { wsStatusMIBGroups 3 } END