ZYXEL-REMOTE-PORT-MIRROR-MIB

File: ZYXEL-REMOTE-PORT-MIRROR-MIB.mib (9030 bytes)

Imported modules

RFC1155-SMI SNMPv2-SMI SNMPv2-TC
RFC1213-MIB P-BRIDGE-MIB Q-BRIDGE-MIB
BRIDGE-MIB IF-MIB SNMP-FRAMEWORK-MIB
INET-ADDRESS-MIB DISMAN-PING-MIB IEEE8021-CFM-MIB
OSPF-MIB ZYXEL-ES-SMI

Imported symbols

enterprises OBJECT-TYPE RowStatus
DateAndTime TruthValue StorageType
MacAddress DisplayString EnabledStatus
PortList dot1dBasePort InterfaceIndexOrZero
SnmpAdminString InetAddressType InetAddress
OperationResponseStatus Counter TimeTicks
BridgeId Timeout dot1agCfmMdIndex
dot1agCfmMaIndex dot1agCfmMepIdentifier IpAddress
ifIndex NOTIFICATION-TYPE sysObjectID
ospfIfIpAddress ospfAddressLessIf ospfAreaId
ospfNbrIpAddr ospfNbrAddressLessIndex ospfLsdbAreaId
ospfLsdbType ospfLsdbLsid ospfLsdbRouterId
ospfVirtIfAreaId ospfVirtIfNeighbor esMgmt

Defined Types

ZyxelRemotePortMirrorEntry  
SEQUENCE    
  zyRemotePortMirrorVid INTEGER
  zyRemotePortMirrorSource8021pPriority INTEGER
  zyRemotePortMirrorSourceIngressMirrorPorts PortList
  zyRemotePortMirrorSourceEgressMirrorPorts PortList
  zyRemotePortMirrorSourceReflectorPortState EnabledStatus
  zyRemotePortMirrorSourceReflectorPort INTEGER
  zyRemotePortMirrorDestinationMonitorPort INTEGER
  zyRemotePortMirrorDestinationMonitorPortTagging EnabledStatus
  zyRemotePortMirrorConnectedPorts PortList
  zyRemotePortMirrorRowStatus RowStatus

Defined Values

zyxelRemotePortMirror 1.3.6.1.4.1.890.1.15.3.73
The subtree for remote port mirror
MODULE-IDENTITY    

zyxelRemotePortMirrorSetup 1.3.6.1.4.1.890.1.15.3.73.1
OBJECT IDENTIFIER    

zyRemotePortMirrorMaxNumberOfVlans 1.3.6.1.4.1.890.1.15.3.73.1.1
The maximum number of remote mirror VLAN entries that can be created.
Status: current Access: read-only
OBJECT-TYPE    
  INTEGER  

zyxelRemotePortMirrorTable 1.3.6.1.4.1.890.1.15.3.73.1.2
The table contains remote port mirror configuration.
Status: current Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    ZyxelRemotePortMirrorEntry

zyxelRemotePortMirrorEntry 1.3.6.1.4.1.890.1.15.3.73.1.2.1
An entry contains remote port mirror configuration.
Status: current Access: not-accessible
OBJECT-TYPE    
  ZyxelRemotePortMirrorEntry  

zyRemotePortMirrorVid 1.3.6.1.4.1.890.1.15.3.73.1.2.1.1
Enter the VLAN ID (1 to 4094) of the remote mirror VLAN.
Status: current Access: not-accessible
OBJECT-TYPE    
  INTEGER 1..4094  

zyRemotePortMirrorSource8021pPriority 1.3.6.1.4.1.890.1.15.3.73.1.2.1.2
Select a priority level (0-7) with which the Switch replaces the priority of packets from source port (belonging to this remote mirror VLAN).
Status: current Access: read-write
OBJECT-TYPE    
  INTEGER 0..7  

zyRemotePortMirrorSourceIngressMirrorPorts 1.3.6.1.4.1.890.1.15.3.73.1.2.1.3
Set port members to be the source ingress mirror-port. The mirror-port is the port traffic that we mirrored: 1. Mirror-ports is only existed in source switch. 2. It can be any port type, such as Ether Channel, Fast Ethernet, Gigabit Ethernet, and so forth. 3. It can be monitored in multiple remote mirror VLAN. 4. It cannot be a monitor-port, reflector-port and connected-port.
Status: current Access: read-write
OBJECT-TYPE    
  PortList  

zyRemotePortMirrorSourceEgressMirrorPorts 1.3.6.1.4.1.890.1.15.3.73.1.2.1.4
Set port members to be the source egress mirror-port. The mirror-port is the port traffic that we mirrored: 1. Mirror-ports is only existed in source switch. 2. It can be any port type, such as Ether Channel, Fast Ethernet, Gigabit Ethernet, and so forth. 3. It can be monitored in multiple remote mirror VLAN. 4. It cannot be a monitor-port, reflector-port and connected-port.
Status: current Access: read-write
OBJECT-TYPE    
  PortList  

zyRemotePortMirrorSourceReflectorPortState 1.3.6.1.4.1.890.1.15.3.73.1.2.1.5
Enable/disable multi-mirroring on RMirror Source. Once the multi-mirroring is enabled, the reflector-port can be used in the RMirrore Source.
Status: current Access: read-write
OBJECT-TYPE    
  EnabledStatus  

zyRemotePortMirrorSourceReflectorPort 1.3.6.1.4.1.890.1.15.3.73.1.2.1.6
Set port members to be the source reflector-port. The reflector port is the mechanism that copies packets onto an remote mirror VLAN. The reflector port forwards only traffic from remote mirror VLAN with which it is affiliated: 1. A reflector-port is only existed in source switch. 2. Spanning tree is automatically disabled on a reflector-port. 3. It is a port set to loopback. 4. The reflector port loops back untagged traffic to the switch. The traffic is then placed on the RSPAN VLAN and flooded to any trunk ports that carry the RSPAN VLAN. 5. The reflector-port can not be mirror-port and monitor-port.
Status: current Access: read-write
OBJECT-TYPE    
  INTEGER  

zyRemotePortMirrorDestinationMonitorPort 1.3.6.1.4.1.890.1.15.3.73.1.2.1.7
Set the port number of the destination monitor port. The monitor-port is the port that we can monitor the RMirror traffic: 1. A monitor-port is only in destination switch. 2. It can participate in only one RMirror VLAN at a time. 3. A monitor-port in one RMirror VLAN cannot be another RMirror VLAN. 4. A monitor-port can not be a mirror-port, reflector-port and connected-port.
Status: current Access: read-write
OBJECT-TYPE    
  INTEGER  

zyRemotePortMirrorDestinationMonitorPortTagging 1.3.6.1.4.1.890.1.15.3.73.1.2.1.8
Enable/Disable the destination monitor port which packet with tag.
Status: current Access: read-write
OBJECT-TYPE    
  EnabledStatus  

zyRemotePortMirrorConnectedPorts 1.3.6.1.4.1.890.1.15.3.73.1.2.1.9
Set port members to be the connected-port. The connected-port is the physical port connected to other switch in the same remote mirror VLAN: 1. The port must join the remote mirror VLAN. 2. The connected-port can not be mirror-port and monitor-port.
Status: current Access: read-write
OBJECT-TYPE    
  PortList  

zyRemotePortMirrorRowStatus 1.3.6.1.4.1.890.1.15.3.73.1.2.1.10
This object allows entries to be created and deleted from the remote mirror table.
Status: current Access: read-create
OBJECT-TYPE    
  RowStatus