ZYXEL-LOOPGUARD-MIB

File: ZYXEL-LOOPGUARD-MIB.mib (4443 bytes)

Imported modules

RFC1155-SMI SNMPv2-SMI SNMPv2-TC
RFC1213-MIB P-BRIDGE-MIB Q-BRIDGE-MIB
BRIDGE-MIB IF-MIB SNMP-FRAMEWORK-MIB
INET-ADDRESS-MIB DISMAN-PING-MIB IEEE8021-CFM-MIB
OSPF-MIB ZYXEL-ES-SMI

Imported symbols

enterprises OBJECT-TYPE RowStatus
DateAndTime TruthValue StorageType
MacAddress DisplayString EnabledStatus
PortList dot1dBasePort InterfaceIndexOrZero
SnmpAdminString InetAddressType InetAddress
OperationResponseStatus Counter TimeTicks
BridgeId Timeout dot1agCfmMdIndex
dot1agCfmMaIndex dot1agCfmMepIdentifier IpAddress
ifIndex NOTIFICATION-TYPE sysObjectID
ospfIfIpAddress ospfAddressLessIf ospfAreaId
ospfNbrIpAddr ospfNbrAddressLessIndex ospfLsdbAreaId
ospfLsdbType ospfLsdbLsid ospfLsdbRouterId
ospfVirtIfAreaId ospfVirtIfNeighbor esMgmt

Defined Types

ZyxelLoopGuardPortEntry  
SEQUENCE    
  zyLoopGuardPortState EnabledStatus

Defined Values

zyxelLoopGuard 1.3.6.1.4.1.890.1.15.3.45
The subtree for loop guard
MODULE-IDENTITY    

zyxelLoopGuardSetup 1.3.6.1.4.1.890.1.15.3.45.1
OBJECT IDENTIFIER    

zyxelLoopGuardNotifications 1.3.6.1.4.1.890.1.15.3.45.2
OBJECT IDENTIFIER    

zyLoopGuardState 1.3.6.1.4.1.890.1.15.3.45.1.1
Enable/Disable loop guard on the switch. Loop guard allows you to configure the switch to shut down a port if it detects that packets sent out on that port loop back to the switch. Loop guard is designed to handle loop problems on the edge of your network. This can occur when a port is connected to a switch that is in a loop state. Loop state occurs as a result of human error. For example, it happens when two ports on a switch are connected with the same cable. When a switch in loop state sends out broadcast messages the messages loop back to the switch and are re-broadcast again and again causing a broadcast storm.
Status: current Access: read-write
OBJECT-TYPE    
  EnabledStatus  

zyxelLoopGuardPortTable 1.3.6.1.4.1.890.1.15.3.45.1.2
The table contains loop guard port configuration.
Status: current Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    ZyxelLoopGuardPortEntry

zyxelLoopGuardPortEntry 1.3.6.1.4.1.890.1.15.3.45.1.2.1
An entry contains loop guard port configuration.
Status: current Access: not-accessible
OBJECT-TYPE    
  ZyxelLoopGuardPortEntry  

zyLoopGuardPortState 1.3.6.1.4.1.890.1.15.3.45.1.2.1.1
Enable/Disable loop guard on the port.
Status: current Access: read-write
OBJECT-TYPE    
  EnabledStatus  

zyLoopGuardLoopDetect 1.3.6.1.4.1.890.1.15.3.45.2.1
Loop guard shuts down the port for loop is detected.
Status: current Access: read-write
NOTIFICATION-TYPE