ZYXEL-LAG-MIB

File: ZYXEL-LAG-MIB.mib (9086 bytes)

Imported modules

SNMPv2-SMI SNMPv2-TC P-BRIDGE-MIB
BRIDGE-MIB ZYXEL-ES-SMI

Imported symbols

OBJECT-TYPE MODULE-IDENTITY DisplayString
EnabledStatus dot1dBasePort esMgmt

Defined Types

ZyxelAggregationGroupEntry  
SEQUENCE    
  zyAggregationGroupIndex INTEGER
  zyAggregationGroupState EnabledStatus
  zyAggregationGroupDynamicState EnabledStatus
  zyAggregationGroupCriteria INTEGER

ZyxelAggregationPortEntry  
SEQUENCE    
  zyAggregationPortGroup INTEGER
  zyAggregationPortDynamicStateTimeout INTEGER

ZyAggregationAutoLacpEntry  
SEQUENCE    
  zyAggregationAutoLacpTrunkGroup INTEGER
  zyAggregationAutoLacpRemoteChassisId DisplayString
  zyAggregationAutoLacpRemotePort INTEGER

Defined Values

zyxelLinkAggregation 1.3.6.1.4.1.890.1.15.3.42
The subtree for link aggregation
MODULE-IDENTITY    

zyxelAggregationSetup 1.3.6.1.4.1.890.1.15.3.42.1
OBJECT IDENTIFIER    

zyxelAggregationStatus 1.3.6.1.4.1.890.1.15.3.42.2
OBJECT IDENTIFIER    

zyAggregationState 1.3.6.1.4.1.890.1.15.3.42.1.1
Enable/Disable link aggregation control protocol.
Status: current Access: read-write
OBJECT-TYPE    
  EnabledStatus  

zyAggregationSysPriority 1.3.6.1.4.1.890.1.15.3.42.1.2
The system number is to set the priority of an active port using link aggregation control protocol. The smaller the number, the higher the priority level.
Status: current Access: read-write
OBJECT-TYPE    
  INTEGER  

zyxelAggregationGroupTable 1.3.6.1.4.1.890.1.15.3.42.1.3
The table contains aggregation group configuration.
Status: current Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    ZyxelAggregationGroupEntry

zyxelAggregationGroupEntry 1.3.6.1.4.1.890.1.15.3.42.1.3.1
An entry contains aggregation group configuration.
Status: current Access: not-accessible
OBJECT-TYPE    
  ZyxelAggregationGroupEntry  

zyAggregationGroupIndex 1.3.6.1.4.1.890.1.15.3.42.1.3.1.1
Index of link aggregation group.
Status: current Access: not-accessible
OBJECT-TYPE    
  INTEGER  

zyAggregationGroupState 1.3.6.1.4.1.890.1.15.3.42.1.3.1.2
Enable/Disable link aggregation control protocol on a special group.
Status: current Access: read-write
OBJECT-TYPE    
  EnabledStatus  

zyAggregationGroupDynamicState 1.3.6.1.4.1.890.1.15.3.42.1.3.1.3
Enable/Disable dynamic link aggregation control protocol on a special group.
Status: current Access: read-write
OBJECT-TYPE    
  EnabledStatus  

zyAggregationGroupCriteria 1.3.6.1.4.1.890.1.15.3.42.1.3.1.4
Outgoing traffic distribution type. Packets from the same source and/or to the same destination are sent over the same link within the trunk. By default, the switch uses the srcDstMac distribution type. If the switch is behind a router, the packet's destination or source MAC address will be changed. In this case, set the switch to distribute traffic based on its IP address to make sure port trunking can work properly.
Status: current Access: read-write
OBJECT-TYPE    
  INTEGER srcMac(1), dstMac(2), srcDstMac(3), srcIp(4), dstIp(5), srcDstIp(6)  

zyxelAggregationPortTable 1.3.6.1.4.1.890.1.15.3.42.1.4
The table contains aggregation port configuration.
Status: current Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    ZyxelAggregationPortEntry

zyxelAggregationPortEntry 1.3.6.1.4.1.890.1.15.3.42.1.4.1
An entry contains aggregation port configuration.
Status: current Access: not-accessible
OBJECT-TYPE    
  ZyxelAggregationPortEntry  

zyAggregationPortGroup 1.3.6.1.4.1.890.1.15.3.42.1.4.1.1
Trunk group which a port belongs.
Status: current Access: read-write
OBJECT-TYPE    
  INTEGER none(0), t1(1), t2(2), t3(3), t4(4), t5(5), t6(6), t7(7), t8(8), t9(9), t10(10), t11(11), t12(12), t13(13), t14(14), t15(15), t16(16), t17(17), t18(18), t19(19), t20(20), t21(21), t22(22), t23(23), t24(24)  

zyAggregationPortDynamicStateTimeout 1.3.6.1.4.1.890.1.15.3.42.1.4.1.2
This timeout is the time interval bEtween the individual port exchanges of LACP packets in order to check that the peer port in the trunk group is still up.
Status: current Access: read-write
OBJECT-TYPE    
  INTEGER  

zyAggregationAutoLacpState 1.3.6.1.4.1.890.1.15.3.42.1.5
Enable/Disable Automatic link aggregation control protocol.
Status: current Access: read-write
OBJECT-TYPE    
  EnabledStatus  

zyAggregationAutoLacpTable 1.3.6.1.4.1.890.1.15.3.42.2.1
The table contains auto-lacp port configuration.
Status: current Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    ZyAggregationAutoLacpEntry

zyAggregationAutoLacpEntry 1.3.6.1.4.1.890.1.15.3.42.2.1.1
An entry contains auto-lacp port configuration.
Status: current Access: not-accessible
OBJECT-TYPE    
  ZyAggregationAutoLacpEntry  

zyAggregationAutoLacpTrunkGroup 1.3.6.1.4.1.890.1.15.3.42.2.1.1.1
Trunk group which a port belongs.
Status: current Access: read-only
OBJECT-TYPE    
  INTEGER none(0), t1(1), t2(2), t3(3), t4(4), t5(5), t6(6), t7(7), t8(8), t9(9), t10(10), t11(11), t12(12), t13(13), t14(14), t15(15), t16(16), t17(17), t18(18), t19(19), t20(20), t21(21), t22(22), t23(23), t24(24)  

zyAggregationAutoLacpRemoteChassisId 1.3.6.1.4.1.890.1.15.3.42.2.1.1.2
This is the chassis id of the remote device.
Status: current Access: read-only
OBJECT-TYPE    
  DisplayString  

zyAggregationAutoLacpRemotePort 1.3.6.1.4.1.890.1.15.3.42.2.1.1.3
This is the connected port of the remote device.
Status: current Access: read-only
OBJECT-TYPE    
  INTEGER