Wellfleet-Series7-MIB

File: Wellfleet-Series7-MIB.mib (560358 bytes)

Imported modules

RFC1155-SMI RFC-1212 RFC1213-MIB

Imported symbols

IpAddress Counter Gauge
TimeTicks Opaque enterprises
OBJECT-TYPE DisplayString

Defined Types

WfAppleRtmpEntry  
SEQUENCE    
  wfAppleRtmpNetStart INTEGER
  wfAppleRtmpNetEnd INTEGER
  wfAppleRtmpPort INTEGER
  wfAppleRtmpHops INTEGER
  wfAppleRtmpNextHopNet INTEGER
  wfAppleRtmpNextHopNode INTEGER
  wfAppleRtmpState INTEGER

WfApplePortEntry  
SEQUENCE    
  wfApplePortDelete INTEGER
  wfApplePortDisable INTEGER
  wfApplePortCircuit INTEGER
  wfApplePortState INTEGER
  wfApplePortType INTEGER
  wfApplePortCksumDisable INTEGER
  wfApplePortTrEndStation INTEGER
  wfApplePortGniForever INTEGER
  wfApplePortAarpFlush INTEGER
  wfApplePortMacAddress OCTET STRING
  wfApplePortNodeId INTEGER
  wfApplePortNetwork INTEGER
  wfApplePortNetStart INTEGER
  wfApplePortNetEnd INTEGER
  wfApplePortDfltZone DisplayString
  wfApplePortCurMacAddress OCTET STRING
  wfApplePortCurNodeId INTEGER
  wfApplePortCurNetwork INTEGER
  wfApplePortCurNetStart INTEGER
  wfApplePortCurNetEnd INTEGER
  wfApplePortCurDfltZone DisplayString
  wfApplePortAarpProbeRxs Counter
  wfApplePortAarpProbeTxs Counter
  wfApplePortAarpReqRxs Counter
  wfApplePortAarpReqTxs Counter
  wfApplePortAarpRspRxs Counter
  wfApplePortAarpRspTxs Counter
  wfApplePortDdpOutRequests Counter
  wfApplePortDdpInReceives Counter
  wfApplePortDdpInLocalDatagrams Counter
  wfApplePortDdpNoProtocolHandlers Counter
  wfApplePortDdpTooShortErrors Counter
  wfApplePortDdpTooLongErrors Counter
  wfApplePortDdpChecksumErrors Counter
  wfApplePortDdpForwRequests Counter
  wfApplePortDdpOutNoRoutes Counter
  wfApplePortDdpBroadcastErrors Counter
  wfApplePortDdpHopCountErrors Counter
  wfApplePortRtmpInDataPkts Counter
  wfApplePortRtmpOutDataPkts Counter
  wfApplePortRtmpInRequestPkts Counter
  wfApplePortRtmpNextIREqualChanges Counter
  wfApplePortRtmpNextIRLessChanges Counter
  wfApplePortRtmpRouteDeletes Counter
  wfApplePortRtmpNetworkMismatchErrors Counter
  wfApplePortRtmpRoutingTableOverflows Counter
  wfApplePortZipInZipQueries Counter
  wfApplePortZipInZipReplies Counter
  wfApplePortZipOutZipReplies Counter
  wfApplePortZipInZipExtendedReplies Counter
  wfApplePortZipOutZipExtendedReplies Counter
  wfApplePortZipInGetZoneLists Counter
  wfApplePortZipOutGetZoneListReplies Counter
  wfApplePortZipInGetLocalZones Counter
  wfApplePortZipOutGetLocalZoneReplies Counter
  wfApplePortZipInGetMyZones Counter
  wfApplePortZipOutGetMyZoneReplies Counter
  wfApplePortZipZoneConflictErrors Counter
  wfApplePortZipInGetNetInfos Counter
  wfApplePortZipOutGetNetInfoReplies Counter
  wfApplePortZipZoneOutInvalids Counter
  wfApplePortZipAddressInvalids Counter
  wfApplePortZipOutGetNetInfos Counter
  wfApplePortZipInGetNetInfoReplies Counter
  wfApplePortZipOutZipQueries Counter
  wfApplePortZipInErrors Counter
  wfApplePortNbpInLookUpRequests Counter
  wfApplePortNbpInLookUpReplies Counter
  wfApplePortNbpInBroadcastRequests Counter
  wfApplePortNbpInForwardRequests Counter
  wfApplePortNbpOutLookUpRequests Counter
  wfApplePortNbpOutLookUpReplies Counter
  wfApplePortNbpOutBroadcastRequests Counter
  wfApplePortNbpOutForwardRequests Counter
  wfApplePortNbpRegistrationFailures Counter
  wfApplePortNbpInErrors Counter
  wfApplePortEchoRequests Counter
  wfApplePortEchoReplies Counter

WfAppleLclZoneEntry  
SEQUENCE    
  wfAppleLclZoneDelete INTEGER
  wfAppleLclZonePortCircuit INTEGER
  wfAppleLclZoneIndex INTEGER
  wfAppleLclZoneName DisplayString

WfAppleAarpEntry  
SEQUENCE    
  wfAppleAarpIfIndex INTEGER
  wfAppleAarpNet INTEGER
  wfAppleAarpNode INTEGER
  wfAppleAarpPhysAddress OCTET STRING

WfAppleZipEntry  
SEQUENCE    
  wfAppleZipZoneNetStart INTEGER
  wfAppleZipZoneNetEnd INTEGER
  wfAppleZipIndex INTEGER
  wfAppleZipZoneName DisplayString
  wfAppleZipZoneState INTEGER

WfBrTpFdbEntry  
SEQUENCE    
  wfBrTpBaseFdbAddress OCTET STRING
  wfBrTpBaseFdbPort INTEGER
  wfBrTpBaseFdbStatus INTEGER

WfBrTpInterfaceEntry  
SEQUENCE    
  wfBrTpInterfaceDelete INTEGER
  wfBrTpInterfaceEnable INTEGER
  wfBrTpInterfaceState INTEGER
  wfBrTpInterfaceCircuit INTEGER
  wfBrTpInterfaceMaxInfo INTEGER
  wfBrTpInterfaceInFrames Counter
  wfBrTpInterfaceOutFrames Counter
  wfBrTpInterfaceInDiscards Counter

WfBrTrafficFilterEntry  
SEQUENCE    
  wfBrTrafficFilterCreate INTEGER
  wfBrTrafficFilterEnable INTEGER
  wfBrTrafficFilterStatus INTEGER
  wfBrTrafficFilterCounter Counter
  wfBrTrafficFilterDefinition Opaque
  wfBrTrafficFilterReserved INTEGER
  wfBrTrafficFilterCircuit INTEGER
  wfBrTrafficFilterRuleNumber INTEGER
  wfBrTrafficFilterFragment INTEGER

WfCctOptsEntry  
SEQUENCE    
  wfCctOptsDelete INTEGER
  wfCctOptsPriorityQueueingDisable INTEGER
  wfCctOptsCct INTEGER
  wfCctOptsHighPriorityQueueLimit INTEGER
  wfCctOptsNormalPriorityQueueLimit INTEGER
  wfCctOptsLowPriorityQueueLimit INTEGER
  wfCctOptsMaxInterruptQueueLatency INTEGER
  wfCctOptsMaxHighPriorityQueueLatency INTEGER
  wfCctOptsHiXmits Counter
  wfCctOptsNormalXmits Counter
  wfCctOptsLoXmits Counter
  wfCctOptsHiClippedPkts Counter
  wfCctOptsNormalClippedPkts Counter
  wfCctOptsLoClippedPkts Counter
  wfCctOptsIntrQHighWaterPkts Gauge
  wfCctOptsHiQHighWaterPkts Gauge
  wfCctOptsNormalQHighWaterPkts Gauge
  wfCctOptsLoQHighWaterPkts Gauge
  wfCctOptsHighWaterPktsClear INTEGER
  wfCctOptsDroppedPkts Counter
  wfCctOptsLargePkts Counter
  wfCctOptsRxPkts Counter

WfCctOptsBrFilterEntry  
SEQUENCE    
  wfCctOptsBrFilterCreate INTEGER
  wfCctOptsBrFilterEnable INTEGER
  wfCctOptsBrFilterState INTEGER
  wfCctOptsBrFilterCounter Counter
  wfCctOptsBrFilterDefinition OCTET STRING
  wfCctOptsBrFilterReserved INTEGER
  wfCctOptsBrFilterCct INTEGER
  wfCctOptsBrFilterRuleNumber INTEGER
  wfCctOptsBrFilterFragment INTEGER

WfCctOptsIpFilterEntry  
SEQUENCE    
  wfCctOptsIpFilterCreate INTEGER
  wfCctOptsIpFilterEnable INTEGER
  wfCctOptsIpFilterState INTEGER
  wfCctOptsIpFilterCounter Counter
  wfCctOptsIpFilterDefinition OCTET STRING
  wfCctOptsIpFilterReserved INTEGER
  wfCctOptsIpFilterCct INTEGER
  wfCctOptsIpFilterRuleNumber INTEGER
  wfCctOptsIpFilterFragment INTEGER

WfCctOptsLengthBasedEntry  
SEQUENCE    
  wfCctOptsLengthBasedDelete INTEGER
  wfCctOptsLengthBasedDisable INTEGER
  wfCctOptsLengthBasedState INTEGER
  wfCctOptsLengthBasedCct INTEGER
  wfCctOptsLengthBasedMux INTEGER
  wfCctOptsLengthBasedData OCTET STRING
  wfCctOptsLengthBasedLength INTEGER
  wfCctOptsLengthBasedLessThanQ INTEGER
  wfCctOptsLengthBasedGreaterThanQ INTEGER

WfCircuitNameEntry  
SEQUENCE    
  wfCircuitNameDelete INTEGER
  wfCircuitNumber INTEGER
  wfCircuitName DisplayString
  wfCircuitIfType INTEGER
  wfCircuitProtoMap OCTET STRING

WfCSMACDEntry  
SEQUENCE    
  wfCSMACDDelete INTEGER
  wfCSMACDEnable INTEGER
  wfCSMACDState INTEGER
  wfCSMACDSlot INTEGER
  wfCSMACDConnector INTEGER
  wfCSMACDCct INTEGER
  wfCSMACDBofl INTEGER
  wfCSMACDBoflTmo INTEGER
  wfCSMACDMtu INTEGER
  wfCSMACDMadr OCTET STRING
  wfCSMACDOctetsRxOk Counter
  wfCSMACDFramesRxOk Counter
  wfCSMACDOctetsTxOk Counter
  wfCSMACDFramesTxOk Counter
  wfCSMACDDeferredTx Counter
  wfCSMACDLateCollnTx Counter
  wfCSMACDExcessvCollnTx Counter
  wfCSMACDBablErrorTx Counter
  wfCSMACDBufErrorTx Counter
  wfCSMACDLcarTx Counter
  wfCSMACDUfloTx Counter
  wfCSMACDFcsErrorRx Counter
  wfCSMACDAlignErrorRx Counter
  wfCSMACDLackRescErrorRx Counter
  wfCSMACDTooLongErrorRx Counter
  wfCSMACDOfloRx Counter
  wfCSMACDMerr Counter
  wfCSMACDCerr Counter
  wfCSMACDHardwareFilter INTEGER
  wfCSMACDTxQueueLength INTEGER
  wfCSMACDRxQueueLength INTEGER
  wfCSMACDTxClipFrames Counter
  wfCSMACDRxReplenMisses Counter

WfivCircuitEntry  
SEQUENCE    
  wfivCircuitCreateDelete INTEGER
  wfivCircuitEnableDisable INTEGER
  wfivCircuitCommonState INTEGER
  wfivCircuitArea INTEGER
  wfivCircuitNodeid INTEGER
  wfivCircuitNodeAddr DisplayString
  wfivCircuitID INTEGER
  wfivCircuitCommonType INTEGER
  wfivCircuitExecCost INTEGER
  wfivCircuitExecHelloTimer INTEGER
  wfivCircuitDesigRouterNodeAddr DisplayString
  wfivCircuitMaxRouters INTEGER
  wfivCircuitRouterPri INTEGER
  wfivCircuitCountAgedPktLoss Counter
  wfivCircuitCountNodeUnrPktLoss Counter
  wfivCircuitCountOutRngePktLoss Counter
  wfivCircuitCountOverSzePktLoss Counter
  wfivCircuitCountPacketFmtErr Counter
  wfivCircuitCountPtlRteUpdtLoss Counter
  wfivCircuitCountTransitPksRecd Counter
  wfivCircuitCountTransitPkSent Counter
  wfivCircuitCountRtHelloSent Counter
  wfivCircuitCountRtHelloRcvd Counter
  wfivCircuitCountHelloSent Counter
  wfivCircuitCountHelloRcvd Counter
  wfivCircuitCountL1UpdSent Counter
  wfivCircuitCountL1UpdRcvd Counter
  wfivCircuitCountAreaUpdSent Counter
  wfivCircuitCountAreaUpdRcvd Counter
  wfivCircuitCountDropped Counter
  wfivCircuitAllEndnodesMac OCTET STRING
  wfivCircuitAllRoutersMac OCTET STRING
  wfivCircuitAllAreaRoutersMac OCTET STRING
  wfivCircuitHelloEnableDisable INTEGER
  wfivCircuitRtHelloEnableDisable INTEGER
  wfivCircuitL1UpdateEnableDisable INTEGER

WfivLevel1RouteEntry  
SEQUENCE    
  wfivLevel1AreaId INTEGER
  wfivLevel1NodeId INTEGER
  wfivLevel1RouteNodeAddr DisplayString
  wfivLevel1RouteCircuitID INTEGER
  wfivLevel1RouteCost INTEGER
  wfivLevel1RouteHops INTEGER
  wfivLevel1RouteNextNode DisplayString

WfivAreaEntry  
SEQUENCE    
  wfivAreaNum INTEGER
  wfivAreaState INTEGER
  wfivAreaCost INTEGER
  wfivAreaHops INTEGER
  wfivAreaCircuitID INTEGER
  wfivAreaNextNode DisplayString

WfivAdjEntry  
SEQUENCE    
  wfivAdjIndex INTEGER
  wfivAdjNodeAddr DisplayString
  wfivAdjBlockSize INTEGER
  wfivAdjListenTimer INTEGER
  wfivAdjCircuitID INTEGER
  wfivAdjType INTEGER
  wfivAdjState INTEGER
  wfivAdjPriority INTEGER
  wfivAdjClass INTEGER

WfivTrafficFilterEntry  
SEQUENCE    
  wfivTrafficFilterCreate INTEGER
  wfivTrafficFilterEnable INTEGER
  wfivTrafficFilterStatus INTEGER
  wfivTrafficFilterCounter Counter
  wfivTrafficFilterDefinition Opaque
  wfivTrafficFilterReserved INTEGER
  wfivTrafficFilterCircuit INTEGER
  wfivTrafficFilterRuleNumber INTEGER
  wfivTrafficFilterFragment INTEGER

WfivStaticAdjEntry  
SEQUENCE    
  wfivStaticAdjCreateDelete INTEGER
  wfivStaticAdjEnableDisable INTEGER
  wfivStaticAdjArea INTEGER
  wfivStaticAdjNodeid INTEGER
  wfivStaticAdjCircuitID INTEGER
  wfivStaticAdjNodeAddr DisplayString
  wfivStaticAdjType INTEGER
  wfivStaticAdjPriority INTEGER
  wfivStaticAdjDestMACAddr OCTET STRING

WfDs1ConfigEntry  
SEQUENCE    
  wfDs1LineIndex INTEGER
  wfDs1TimeElapsed INTEGER
  wfDs1ValidIntervals INTEGER
  wfDs1LineType INTEGER
  wfDs1ZeroCoding INTEGER
  wfDs1SendCode INTEGER
  wfDs1CircuitIdentifier DisplayString
  wfDs1LoopbackConfig INTEGER
  wfDs1LineStatus INTEGER

WfDs1CurrentEntry  
SEQUENCE    
  wfDs1CurrentIndex INTEGER
  wfDs1CurrentESs Counter
  wfDs1CurrentSESs Counter
  wfDs1CurrentSEFs Counter
  wfDs1CurrentUASs Counter
  wfDs1CurrentBPVs Counter
  wfDs1CurrentCVs Counter

WfDs1IntervalEntry  
SEQUENCE    
  wfDs1IntervalIndex INTEGER
  wfDs1IntervalNumber INTEGER
  wfDs1IntervalESs Gauge
  wfDs1IntervalSESs Gauge
  wfDs1IntervalSEFs Gauge
  wfDs1IntervalUASs Gauge
  wfDs1IntervalBPVs Gauge
  wfDs1IntervalCVs Gauge

WfDs1TotalEntry  
SEQUENCE    
  wfDs1TotalIndex INTEGER
  wfDs1TotalESs Gauge
  wfDs1TotalSESs Gauge
  wfDs1TotalSEFs Gauge
  wfDs1TotalUASs Gauge
  wfDs1TotalBPVs Gauge
  wfDs1TotalCVs Gauge

WfDs1FeCurrentEntry  
SEQUENCE    
  wfDs1FeCurrentIndex INTEGER
  wfDs1FeCurrentESs Counter
  wfDs1FeCurrentSESs Counter
  wfDs1FeCurrentSEFs Counter
  wfDs1FeCurrentBPVs Counter
  wfDs1FeCurrentCVs Counter

WfDs1FeIntervalEntry  
SEQUENCE    
  wfDs1FeIntervalIndex INTEGER
  wfDs1FeIntervalNumber INTEGER
  wfDs1FeIntervalESs Gauge
  wfDs1FeIntervalSESs Gauge
  wfDs1FeIntervalSEFs Gauge
  wfDs1FeIntervalBPVs Gauge
  wfDs1FeIntervalCVs Gauge

WfDs1FeTotalEntry  
SEQUENCE    
  wfDs1FeTotalIndex INTEGER
  wfDs1FeTotalESs Gauge
  wfDs1FeTotalSESs Gauge
  wfDs1FeTotalSEFs Gauge
  wfDs1FeTotalBPVs Gauge
  wfDs1FeTotalCVs Gauge

WfDs3ConfigEntry  
SEQUENCE    
  wfDs3LineIndex INTEGER
  wfDs3TimeElapsed INTEGER
  wfDs3ValidIntervals INTEGER
  wfDs3LineType INTEGER
  wfDs3ZeroCoding INTEGER
  wfDs3SendCode INTEGER
  wfDs3CircuitIdentifier DisplayString
  wfDs3LoopbackConfig INTEGER
  wfDs3LineStatus INTEGER

WfDs3CurrentEntry  
SEQUENCE    
  wfDs3CurrentIndex INTEGER
  wfDs3CurrentESs Counter
  wfDs3CurrentSESs Counter
  wfDs3CurrentSEFs Counter
  wfDs3CurrentUASs Counter
  wfDs3CurrentBPVs Counter
  wfDs3CurrentCVs Counter

WfDs3IntervalEntry  
SEQUENCE    
  wfDs3IntervalIndex INTEGER
  wfDs3IntervalNumber INTEGER
  wfDs3IntervalESs Gauge
  wfDs3IntervalSESs Gauge
  wfDs3IntervalSEFs Gauge
  wfDs3IntervalUASs Gauge
  wfDs3IntervalBPVs Gauge
  wfDs3IntervalCVs Gauge

WfDs3TotalEntry  
SEQUENCE    
  wfDs3TotalIndex INTEGER
  wfDs3TotalESs Gauge
  wfDs3TotalSESs Gauge
  wfDs3TotalSEFs Gauge
  wfDs3TotalUASs Gauge
  wfDs3TotalBPVs Gauge
  wfDs3TotalCVs Gauge

WfDs3FeConfigEntry  
SEQUENCE    
  wfDs3FeConfigIndex INTEGER
  wfDs3FarEndEquipCode DisplayString
  wfDs3FarEndLocationIDCode DisplayString
  wfDs3FarEndFrameIDCode DisplayString
  wfDs3FarEndUnitCode DisplayString
  wfDs3FarEndFacilityIDCode DisplayString

WfDs3FeCurrentEntry  
SEQUENCE    
  wfDs3FeCurrentIndex INTEGER
  wfDs3FeCurrentESs Counter
  wfDs3FeCurrentSESs Counter
  wfDs3FeCurrentCVs Counter

WfDs3FeIntervalEntry  
SEQUENCE    
  wfDs3FeIntervalIndex INTEGER
  wfDs3FeIntervalNumber INTEGER
  wfDs3FeIntervalESs Gauge
  wfDs3FeIntervalSESs Gauge
  wfDs3FeIntervalCVs Gauge

WfDs3FeTotalEntry  
SEQUENCE    
  wfDs3FeTotalIndex INTEGER
  wfDs3FeTotalESs Gauge
  wfDs3FeTotalSESs Gauge
  wfDs3FeTotalCVs Gauge

WfE1Entry  
SEQUENCE    
  wfE1Delete INTEGER
  wfE1Disable INTEGER
  wfE1State INTEGER
  wfE1Slot INTEGER
  wfE1Connector INTEGER
  wfE1Madr OCTET STRING
  wfE1HDB3Support INTEGER
  wfE1ClockMode INTEGER
  wfE1MiniDacs DisplayString
  wfE1BipolarVios Counter
  wfE1FrameErrs Counter
  wfE1RcvRemAlms Counter
  wfE1RcvMfmAlms Counter
  wfE1MfsErrs Counter
  wfE1SyncLoss Counter
  wfE1RcvSig1s Counter
  wfE1RcvUnfrm1s Counter

WfFddiEntry  
SEQUENCE    
  wfFDDIDelete INTEGER
  wfFDDIEnable INTEGER
  wfFDDIState INTEGER
  wfFDDISlot INTEGER
  wfFDDINode INTEGER
  wfFDDICct INTEGER
  wfFDDIBofl INTEGER
  wfFDDIBoflTmo INTEGER
  wfFDDIMtu INTEGER
  wfFDDIMadr OCTET STRING
  wfFDDIOctetsRxOk Counter
  wfFDDIFramesRxOk Counter
  wfFDDIOctetsTxOk Counter
  wfFDDIFramesTxOk Counter
  wfFDDICrcErrRx Counter
  wfFDDIOverrunRx Counter
  wfFDDIParityErrRx Counter
  wfFDDIMacErrRx Counter
  wfFDDIRingErrRx Counter
  wfFDDISmtRingErrRx Counter
  wfFDDIRingOverrunRx Counter
  wfFDDISmtRingOverrunRx Counter
  wfFDDIAbortTx Counter
  wfFDDIUnderrunTx Counter
  wfFDDIParityErrTx Counter
  wfFDDIRingErrTx Counter
  wfFDDIPortOpErr Counter
  wfFDDIInternOpErr Counter
  wfFDDIHostErr Counter
  wfFDDISmtConnectionPolicy INTEGER
  wfFDDISmtTNotify INTEGER
  wfFDDIMacTReq INTEGER
  wfFDDIMacTMax INTEGER
  wfFDDIMacTvxValue INTEGER
  wfFDDIMacTMin INTEGER
  wfFDDIHardwareFilter INTEGER
  wfFDDISmtEnable INTEGER
  wfFDDITxQueueLength INTEGER
  wfFDDIRxQueueLength INTEGER
  wfFDDITxClipFrames Counter
  wfFDDIRxReplenMisses Counter

WfFddiSmtEntry  
SEQUENCE    
  wfFddiSmtSlot INTEGER
  wfFddiSmtNode INTEGER
  wfFddiSmtCct INTEGER
  wfFddiSmtStationId OCTET STRING
  wfFddiSmtOpVersionId INTEGER
  wfFddiSmtMacCt INTEGER
  wfFddiSmtNonMasterCt INTEGER
  wfFddiSmtEcmState INTEGER
  wfFddiSmtCfState INTEGER

WfFddiMacEntry  
SEQUENCE    
  wfFddiMacSlot INTEGER
  wfFddiMacNode INTEGER
  wfFddiMacCct INTEGER
  wfFddiMacUpstreamNbr OCTET STRING
  wfFddiMacDownstreamNbr OCTET STRING
  wfFddiMacSmtAddress OCTET STRING
  wfFddiMacTNeg INTEGER
  wfFddiMacRmtState INTEGER

WfFddiPortEntry  
SEQUENCE    
  wfFddiPortSlot INTEGER
  wfFddiPortNode INTEGER
  wfFddiPortCct INTEGER
  wfFddiPortIndex INTEGER
  wfFddiPortPcType INTEGER
  wfFddiPortPcNeighbor INTEGER
  wfFddiPortPcmState INTEGER

WfFrDlcmiEntry  
SEQUENCE    
  wfFrDlcmiDelete INTEGER
  wfFrDlcmiDisable INTEGER
  wfFrDlcmiState INTEGER
  wfFrDlcmiCircuit INTEGER
  wfFrDlcmiManagementType INTEGER
  wfFrDlcmiStatus INTEGER
  wfFrDlcmiAddress INTEGER
  wfFrDlcmiAddressLen INTEGER
  wfFrDlcmiPollingInterval INTEGER
  wfFrDlcmiFullEnquiryInterval INTEGER
  wfFrDlcmiErrorThreshold INTEGER
  wfFrDlcmiMonitoredEvents INTEGER
  wfFrDlcmiMaxSupportedVCs INTEGER
  wfFrDlcmiMulticast INTEGER
  wfFrDlcmiSeqCount INTEGER
  wfFrDlcmiLastReceived INTEGER
  wfFrDlcmiPassiveSeqCount INTEGER
  wfFrDlcmiPassiveReceived INTEGER
  wfFrDlcmiPolls INTEGER
  wfFrDlcmiAlarmTimer INTEGER
  wfFrErrType INTEGER
  wfFrErrData OCTET STRING
  wfFrErrTime TimeTicks
  wfFrErrDiscards Counter
  wfFrErrDrops Counter

WfFrCircuitEntry  
SEQUENCE    
  wfFrCircuitDelete INTEGER
  wfFrCircuitNumber INTEGER
  wfFrCircuitDlci INTEGER
  wfFrCircuitState INTEGER
  wfFrCircuitStateSet INTEGER
  wfFrCircuitReceivedFECNs Counter
  wfFrCircuitReceivedBECNs Counter
  wfFrCircuitSentFrames Counter
  wfFrCircuitSentOctets Counter
  wfFrCircuitReceivedFrames Counter
  wfFrCircuitReceivedOctets Counter
  wfFrCircuitCreationTime TimeTicks
  wfFrCircuitLastTimeChange TimeTicks
  wfFrCircuitCommittedBurst INTEGER
  wfFrCircuitExcessBurst INTEGER
  wfFrCircuitThroughput INTEGER
  wfFrCircuitMulticast INTEGER
  wfFrCircuitDiscards Counter
  wfFrCircuitDrops Counter
  wfFrCircuitSubCct INTEGER
  wfFrCircuitMode INTEGER

WfKernelEntry  
SEQUENCE    
  wfKernelSlot INTEGER
  wfKernelMemorySize INTEGER
  wfKernelMemoryFree INTEGER
  wfKernelMemorySegsTotal INTEGER
  wfKernelMemorySegsFree INTEGER
  wfKernelMemoryMaxSegFree INTEGER
  wfKernelBuffersTotal INTEGER
  wfKernelBuffersFree INTEGER
  wfKernelTasksTotal INTEGER
  wfKernelTasksInQueue INTEGER
  wfKernelTimersTotal INTEGER
  wfKernelTimersActive INTEGER
  wfKernelBufOwnerTask1 DisplayString
  wfKernelBufOwnerTask1Bufs INTEGER
  wfKernelBufOwnerTask2 DisplayString
  wfKernelBufOwnerTask2Bufs INTEGER
  wfKernelBufOwnerTask3 DisplayString
  wfKernelBufOwnerTask3Bufs INTEGER
  wfKernelBufOwnerTask4 DisplayString
  wfKernelBufOwnerTask4Bufs INTEGER
  wfKernelBufOwnerTask5 DisplayString
  wfKernelBufOwnerTask5Bufs INTEGER
  wfKernelBufOwnerTask6 DisplayString
  wfKernelBufOwnerTask6Bufs INTEGER
  wfKernelBufOwnerTask7 DisplayString
  wfKernelBufOwnerTask7Bufs INTEGER
  wfKernelBufOwnerTask8 DisplayString
  wfKernelBufOwnerTask8Bufs INTEGER
  wfKernelBufOwnerTask9 DisplayString
  wfKernelBufOwnerTask9Bufs INTEGER
  wfKernelBufOwnerTask10 DisplayString
  wfKernelBufOwnerTask10Bufs INTEGER
  wfKernelMemOwnerTask1 DisplayString
  wfKernelMemOwnerTask1Size INTEGER
  wfKernelMemOwnerTask2 DisplayString
  wfKernelMemOwnerTask2Size INTEGER
  wfKernelMemOwnerTask3 DisplayString
  wfKernelMemOwnerTask3Size INTEGER
  wfKernelMemOwnerTask4 DisplayString
  wfKernelMemOwnerTask4Size INTEGER
  wfKernelMemOwnerTask5 DisplayString
  wfKernelMemOwnerTask5Size INTEGER
  wfKernelMemOwnerTask6 DisplayString
  wfKernelMemOwnerTask6Size INTEGER
  wfKernelMemOwnerTask7 DisplayString
  wfKernelMemOwnerTask7Size INTEGER
  wfKernelMemOwnerTask8 DisplayString
  wfKernelMemOwnerTask8Size INTEGER
  wfKernelMemOwnerTask9 DisplayString
  wfKernelMemOwnerTask9Size INTEGER
  wfKernelMemOwnerTask10 DisplayString
  wfKernelMemOwnerTask10Size INTEGER

WfHwEntry  
SEQUENCE    
  wfHwSlot INTEGER
  wfHwModIdOpt INTEGER
  wfHwModRev OCTET STRING
  wfHwModSerialNumber OCTET STRING
  wfHwMotherBdIdOpt INTEGER
  wfHwMotherBdRev OCTET STRING
  wfHwMotherBdSerialNumber OCTET STRING
  wfHwDaughterBdIdOpt INTEGER
  wfHwDaughterBdRev OCTET STRING
  wfHwDaughterBdSerialNumber OCTET STRING
  wfHwBabyBdIdOpt INTEGER
  wfHwBabyBdRev OCTET STRING
  wfHwBabyBdSerialNumber OCTET STRING
  wfHwDiagPromRev OCTET STRING
  wfHwDiagPromDate DisplayString
  wfHwDiagPromSource DisplayString
  wfHwBootPromRev OCTET STRING
  wfHwBootPromDate DisplayString
  wfHwBootPromSource DisplayString
  wfHwSparePromRev OCTET STRING
  wfHwSparePromDate DisplayString
  wfHwSparePromSource DisplayString
  wfHwFileSysPresent INTEGER

WfHssiEntry  
SEQUENCE    
  wfHssiDelete INTEGER
  wfHssiDisable INTEGER
  wfHssiState INTEGER
  wfHssiSlot INTEGER
  wfHssiConnector INTEGER
  wfHssiCct INTEGER
  wfHssiBofl INTEGER
  wfHssiBoflTmo INTEGER
  wfHssiMtu INTEGER
  wfHssiMadr OCTET STRING
  wfHssiService INTEGER
  wfHssiWanProtocol INTEGER
  wfHssiTransmissionInterface INTEGER
  wfHssiExternalClkSpeed INTEGER
  wfHssiCrcSize INTEGER
  wfHssiInternalClkTestMode INTEGER
  wfHssiRxOctets Counter
  wfHssiRxFrames Counter
  wfHssiTxOctets Counter
  wfHssiTxFrames Counter
  wfHssiInDiscards Counter
  wfHssiInErrors Counter
  wfHssiOutDiscards Counter
  wfHssiOutErrors Counter
  wfHssiRxLongFrames Counter
  wfHssiTxClipFrames Counter
  wfHssiRxReplenMisses Counter
  wfHssiLastRxErrorCtrl INTEGER
  wfHssiRxCrcErrors Counter
  wfHssiRxOverruns Counter
  wfHssiRxAborts Counter
  wfHssiLastTxErrorCtrl INTEGER
  wfHssiTxAborts Counter
  wfHssiTxUnderruns Counter
  wfHssiRxRingErrors Counter
  wfHssiLastRxRingState INTEGER
  wfHssiRxRingOverruns Counter
  wfHssiTxRingErrors Counter
  wfHssiLastTxRingState INTEGER
  wfHssiPortOpErrors Counter
  wfHssiInternOpErrors Counter
  wfHssiHostErrors Counter
  wfHssiRxProcessings Counter
  wfHssiTxProcessings Counter
  wfHssiTxCmplProcessings Counter
  wfHssiIntrProcessings Counter
  wfHssiBoflNum INTEGER
  wfHssiBoflLen INTEGER
  wfHssiRxBufferLength INTEGER
  wfHssiMemPageLength INTEGER
  wfHssiRxRingLength INTEGER
  wfHssiTxRingLength INTEGER
  wfHssiRxFifoWatermark INTEGER
  wfHssiTxFifoWatermark INTEGER
  wfHssiMaxRxMemory INTEGER
  wfHssiLinkInterface INTEGER
  wfHssiTurboBofl INTEGER

WfHwfEntry  
SEQUENCE    
  wfHwfDelete INTEGER
  wfHwfEnable INTEGER
  wfHwfState INTEGER
  wfHwfSlot INTEGER
  wfHwfAvailableLines INTEGER

WfHwfLineEntry  
SEQUENCE    
  wfHwfLineState INTEGER
  wfHwfLineSlot INTEGER
  wfHwfLineNumber INTEGER
  wfHwfLineCct INTEGER
  wfHwfLineCapableMaxTblSize INTEGER
  wfHwfLineCurrentTblSize INTEGER
  wfHwfLineCurrentUsedEntries INTEGER
  wfHwfLineDroppedFrames INTEGER

WfIfEntry  
SEQUENCE    
  wfIfIndex INTEGER
  wfIfDescr DisplayString
  wfIfType INTEGER
  wfIfMtu INTEGER
  wfIfSpeed Gauge
  wfIfPhysAddress OCTET STRING
  wfIfAdminStatus INTEGER
  wfIfOperStatus INTEGER
  wfIfLastChange TimeTicks
  wfIfInOctets Counter
  wfIfInUcastPkts Counter
  wfIfInNUCastPkts Counter
  wfIfInDiscards Counter
  wfIfInErrors Counter
  wfIfInUnknownProtos Counter
  wfIfOutOctets Counter
  wfIfOutUcastPkts Counter
  wfIfOutNUcastPkts Counter
  wfIfOutDiscards Counter
  wfIfOutErrors Counter
  wfIfOutQLen Gauge
  wfIfSpecific OBJECT IDENTIFIER

WfIpBaseRtEntry  
SEQUENCE    
  wfIpBaseRouteDest IpAddress
  wfIpBaseRouteIfIndex INTEGER
  wfIpBaseRouteMetric1 INTEGER
  wfIpBaseRouteMetric2 INTEGER
  wfIpBaseRouteMetric3 INTEGER
  wfIpBaseRouteMetric4 INTEGER
  wfIpBaseRouteNextHop IpAddress
  wfIpBaseRouteType INTEGER
  wfIpBaseRouteProto INTEGER
  wfIpBaseRouteAge INTEGER
  wfIpBaseRouteMask IpAddress
  wfIpBaseRouteMetric5 INTEGER
  wfIpBaseRouteInfo OBJECT IDENTIFIER

WfIpBaseHostEntry  
SEQUENCE    
  wfIpBaseNetToMediaIfIndex INTEGER
  wfIpBaseNetToMediaPhysAddress OCTET STRING
  wfIpBaseNetToMediaNetAddress IpAddress
  wfIpBaseNetToMediaType INTEGER

WfIpInterfaceEntry  
SEQUENCE    
  wfIpInterfaceCreate INTEGER
  wfIpInterfaceEnable INTEGER
  wfIpInterfaceState INTEGER
  wfIpInterfaceAddr IpAddress
  wfIpInterfaceCircuit INTEGER
  wfIpInterfaceMask IpAddress
  wfIpInterfaceCost INTEGER
  wfIpInterfaceCfgBcastAddr IpAddress
  wfIpInterfaceBcastAddr IpAddress
  wfIpInterfaceMTUDiscovery INTEGER
  wfIpInterfaceAMR INTEGER
  wfIpInterfaceASB INTEGER
  wfIpInterfaceAddressResolutionType INTEGER
  wfIpInterfaceProxy INTEGER
  wfIpInterfaceHostCache INTEGER
  wfIpInterfaceUdpXsumOn INTEGER
  wfIpInterfaceCfgMacAddress OCTET STRING
  wfIpInterfaceMacAddress OCTET STRING
  wfIpInterfaceReasmMaxSize INTEGER
  wfIpInterfaceMaxInfo INTEGER
  wfIpInterfaceInReceives Counter
  wfIpInterfaceInHdrErrors Counter
  wfIpInterfaceInAddrErrors Counter
  wfIpInterfaceForwDatagrams Counter
  wfIpInterfaceInUnknownProtos Counter
  wfIpInterfaceInDiscards Counter
  wfIpInterfaceInDelivers Counter
  wfIpInterfaceOutRequests Counter
  wfIpInterfaceOutDiscards Counter
  wfIpInterfaceOutNoRoutes Counter
  wfIpInterfaceReasmTimeout INTEGER
  wfIpInterfaceReasmReqds Counter
  wfIpInterfaceReasmOKs Counter
  wfIpInterfaceReasmFails Counter
  wfIpInterfaceFragOKs Counter
  wfIpInterfaceFragFails Counter
  wfIpInterfaceFragCreates Counter
  wfIpInterfaceIcmpInMsgs Counter
  wfIpInterfaceIcmpInErrors Counter
  wfIpInterfaceIcmpInDestUnreachs Counter
  wfIpInterfaceIcmpInTimeExcds Counter
  wfIpInterfaceIcmpInParmProbs Counter
  wfIpInterfaceIcmpInSrcQuenchs Counter
  wfIpInterfaceIcmpInRedirects Counter
  wfIpInterfaceIcmpInEchos Counter
  wfIpInterfaceIcmpInEchoReps Counter
  wfIpInterfaceIcmpInTimestamps Counter
  wfIpInterfaceIcmpInTimestampReps Counter
  wfIpInterfaceIcmpInAddrMasks Counter
  wfIpInterfaceIcmpInAddrMaskReps Counter
  wfIpInterfaceIcmpOutMsgs Counter
  wfIpInterfaceIcmpOutErrors Counter
  wfIpInterfaceIcmpOutDestUnreachs Counter
  wfIpInterfaceIcmpOutTimeExcds Counter
  wfIpInterfaceIcmpOutParmProbs Counter
  wfIpInterfaceIcmpOutSrcQuenchs Counter
  wfIpInterfaceIcmpOutRedirects Counter
  wfIpInterfaceIcmpOutEchos Counter
  wfIpInterfaceIcmpOutEchoReps Counter
  wfIpInterfaceIcmpOutTimestamps Counter
  wfIpInterfaceIcmpOutTimestampReps Counter
  wfIpInterfaceIcmpOutAddrMasks Counter
  wfIpInterfaceIcmpOutAddrMaskReps Counter
  wfIpInterfaceTrEndStation INTEGER
  wfIpInterfaceSMDSGroupAddress OCTET STRING
  wfIpInterfaceSMDSArpReqAddress OCTET STRING
  wfIpInterfaceFRBcastDlci INTEGER
  wfIpInterfaceFRMcast1Dlci INTEGER
  wfIpInterfaceFRMcast2Dlci INTEGER
  wfIpInterfaceRedirect INTEGER
  wfIpInterfaceEnetArpEncaps INTEGER

WfIpStaticRouteEntry  
SEQUENCE    
  wfIpSrCreate INTEGER
  wfIpSrEnable INTEGER
  wfIpSrIpAddress IpAddress
  wfIpSrIpNetMask IpAddress
  wfIpSrCost INTEGER
  wfIpSrNextHopAddr IpAddress
  wfIpSrNextHopMask IpAddress
  wfIpSrPreference INTEGER
  wfIpSrIpAddressRt INTEGER
  wfIpSrValid INTEGER

WfIpAdjacentHostEntry  
SEQUENCE    
  wfIpAdjHostCreate INTEGER
  wfIpAdjHostEnable INTEGER
  wfIpAdjHostIpAddress IpAddress
  wfIpAdjHostIntf IpAddress
  wfIpAdjHostIntfMask IpAddress
  wfIpAdjHostMacAddr OCTET STRING
  wfIpAdjHostEncaps INTEGER
  wfIpAdjHostValid INTEGER

WfIpTrafficFilterEntry  
SEQUENCE    
  wfIpTrafficFilterCreate INTEGER
  wfIpTrafficFilterEnable INTEGER
  wfIpTrafficFilterStatus INTEGER
  wfIpTrafficFilterCounter Counter
  wfIpTrafficFilterDefinition Opaque
  wfIpTrafficFilterReserved INTEGER
  wfIpTrafficFilterInterface IpAddress
  wfIpTrafficFilterCircuit INTEGER
  wfIpTrafficFilterRuleNumber INTEGER
  wfIpTrafficFilterFragment INTEGER

WfRipIntfEntry  
SEQUENCE    
  wfRipInterfaceCreate INTEGER
  wfRipInterfaceEnable INTEGER
  wfRipInterfaceState INTEGER
  wfRipInterfaceIndex IpAddress
  wfRipInterfaceSupply INTEGER
  wfRipInterfaceListen INTEGER
  wfRipInterfaceDefaultRouteSupply INTEGER
  wfRipInterfaceDefaultRouteListen INTEGER
  wfRipInterfacePoisonedReversed INTEGER

WfArpIntfEntry  
SEQUENCE    
  wfArpCreate INTEGER
  wfArpEnable INTEGER
  wfArpCctno INTEGER

WfIpxBaseRtEntry  
SEQUENCE    
  wfIpxBaseRouteDest OCTET STRING
  wfIpxBaseRouteIfIndex INTEGER
  wfIpxBaseRouteMetric INTEGER
  wfIpxBaseRouteNextHopNetwork OCTET STRING
  wfIpxBaseRouteNextHopHost OCTET STRING
  wfIpxBaseRouteType INTEGER
  wfIpxBaseRouteProto INTEGER
  wfIpxBaseRouteAge INTEGER
  wfIpxBaseRouteInfo OCTET STRING

WfIpxBaseSapEntry  
SEQUENCE    
  wfIpxBaseSapType OCTET STRING
  wfIpxBaseSapNetwork OCTET STRING
  wfIpxBaseSapHost OCTET STRING
  wfIpxBaseSapSocket OCTET STRING
  wfIpxBaseSapName DisplayString
  wfIpxBaseSapAge INTEGER
  wfIpxBaseSapHops INTEGER
  wfIpxBaseSapIndex OCTET STRING
  wfIpxBaseSapIntf OCTET STRING

WfIpxInterfaceEntry  
SEQUENCE    
  wfIpxInterfaceIndex INTEGER
  wfIpxInterfaceDelete INTEGER
  wfIpxInterfaceDisable INTEGER
  wfIpxInterfaceState INTEGER
  wfIpxInterfaceCircuit INTEGER
  wfIpxInterfaceNetworkNumber OCTET STRING
  wfIpxInterfaceCost INTEGER
  wfIpxInterfaceXsumOn INTEGER
  wfIpxInterfaceCfgEncaps INTEGER
  wfIpxInterfaceMacAddress OCTET STRING
  wfIpxInterfaceSMDSGroupAddress OCTET STRING
  wfIpxInterfaceMaxInfo INTEGER
  wfIpxInterfaceInReceives Counter
  wfIpxInterfaceInHdrErrors Counter
  wfIpxInterfaceInAddrErrors Counter
  wfIpxInterfaceForwDatagrams Counter
  wfIpxInterfaceInUnknownProtos Counter
  wfIpxInterfaceInDiscards Counter
  wfIpxInterfaceInDelivers Counter
  wfIpxInterfaceOutRequests Counter
  wfIpxInterfaceOutDiscards Counter
  wfIpxInterfaceOutNoRoutes Counter
  wfIpxInterfaceTrEndStation INTEGER
  wfIpxInterfaceNetbiosAccept INTEGER
  wfIpxInterfaceNetbiosDeliver INTEGER
  wfIpxInterfaceWanSapPeriod INTEGER
  wfIpxInterfaceFRBcast OCTET STRING
  wfIpxInterfaceFRMcast OCTET STRING
  wfIpxInterfaceEncaps INTEGER
  wfIpxInterfaceSplit INTEGER
  wfIpxInterfaceCacheHit Counter

WfIpxRipIntfEntry  
SEQUENCE    
  wfIpxRipInterfaceDelete INTEGER
  wfIpxRipInterfaceDisable INTEGER
  wfIpxRipInterfaceState INTEGER
  wfIpxRipInterfaceIndex OCTET STRING
  wfIpxRipInterfaceSupply INTEGER
  wfIpxRipInterfaceListen INTEGER

WfIpxAdjacentHostEntry  
SEQUENCE    
  wfIpxAhDelete INTEGER
  wfIpxAhDisable INTEGER
  wfIpxAhTargHostNetwork OCTET STRING
  wfIpxAhTargHostId OCTET STRING
  wfIpxAhNextHopIntf OCTET STRING
  wfIpxAhDlci OCTET STRING

WfIpxStaticRouteEntry  
SEQUENCE    
  wfIpxSrDelete INTEGER
  wfIpxSrDisable INTEGER
  wfIpxSrTargNetwork OCTET STRING
  wfIpxSrCost INTEGER
  wfIpxSrNextHopNetwork OCTET STRING
  wfIpxSrNextHopHost OCTET STRING
  wfIpxSrTargNetworkRt INTEGER

WfIpxNetBiosStaticRouteEntry  
SEQUENCE    
  wfIpxNetBiosSrDelete INTEGER
  wfIpxNetBiosSrDisable INTEGER
  wfIpxNetBiosSrTargNetwork OCTET STRING
  wfIpxNetBiosSrName OCTET STRING
  wfIpxNetBiosSrIntf OCTET STRING
  wfIpxNetBiosSrIndex INTEGER

WfIpxSapNetLvlFilter  
SEQUENCE    
  wfIpxSapNetLvlDelete INTEGER
  wfIpxSapNetLvlDisable INTEGER
  wfIpxSapNetLvlTargNetwork OCTET STRING
  wfIpxSapNetLvlType OCTET STRING
  wfIpxSapNetLvlAction INTEGER
  wfIpxSapNetLvlIntf OCTET STRING
  wfIpxSapNetLvlIndex INTEGER

WfIpxSapServLvlFilter  
SEQUENCE    
  wfIpxSapServLvlDelete INTEGER
  wfIpxSapServLvlDisable INTEGER
  wfIpxSapServLvlTargServer DisplayString
  wfIpxSapServLvlType OCTET STRING
  wfIpxSapServLvlAction INTEGER
  wfIpxSapServLvlIntf OCTET STRING
  wfIpxSapServLvlIndex INTEGER

WfIpxTrafficFilterEntry  
SEQUENCE    
  wfIpxTrafficFilterCreate INTEGER
  wfIpxTrafficFilterEnable INTEGER
  wfIpxTrafficFilterStatus INTEGER
  wfIpxTrafficFilterCounter Counter
  wfIpxTrafficFilterDefinition Opaque
  wfIpxTrafficFilterReserved INTEGER
  wfIpxTrafficFilterInterface OCTET STRING
  wfIpxTrafficFilterCircuit INTEGER
  wfIpxTrafficFilterRuleNumber INTEGER
  wfIpxTrafficFilterFragment INTEGER

WfOspfAreaEntry  
SEQUENCE    
  wfOspfAreaDelete INTEGER
  wfOspfAreaDisable INTEGER
  wfOspfAreaState INTEGER
  wfOspfAreaId IpAddress
  wfOspfAuthType INTEGER
  wfOspfImportASExtern INTEGER
  wfOspfStubMetric INTEGER
  wfOspfImportSum INTEGER

WfOspfLsdbEntry  
SEQUENCE    
  wfOspfLsdbAreaId IpAddress
  wfOspfLsdbType INTEGER
  wfOspfLsdbLSID IpAddress
  wfOspfLsdbRouterId IpAddress
  wfOspfLsdbSequence INTEGER
  wfOspfLsdbAge INTEGER
  wfOspfLsdbChecksum INTEGER
  wfOspfLsdbAdvLen INTEGER

WfOspfAreaRangeEntry  
SEQUENCE    
  wfOspfAreaRangeDelete INTEGER
  wfOspfAreaRangeDisable INTEGER
  wfOspfAreaRangeState INTEGER
  wfOspfAreaRangeAreaID IpAddress
  wfOspfAreaRangeNet IpAddress
  wfOspfAreaRangeMask IpAddress

WfOspfIfEntry  
SEQUENCE    
  wfOspfIfDelete INTEGER
  wfOspfIfDisable INTEGER
  wfOspfIfState INTEGER
  wfOspfIfIpAddress IpAddress
  wfOspfAddressLessIf INTEGER
  wfOspfIfAreaId IpAddress
  wfOspfIfType INTEGER
  wfOspfIfRtrPriority INTEGER
  wfOspfIfTransitDelay INTEGER
  wfOspfIfRetransInterval INTEGER
  wfOspfIfHelloInterval INTEGER
  wfOspfIfRtrDeadInterval INTEGER
  wfOspfIfPollInterval INTEGER
  wfOspfIfDesignatedRouter IpAddress
  wfOspfIfBackupDesignatedRouter IpAddress
  wfOspfIfMetricCost INTEGER
  wfOspfIfAuthKey OCTET STRING
  wfOspfIfTxHellos Counter
  wfOspfIfTxDBDescripts Counter
  wfOspfIfTxLinkStateReqs Counter
  wfOspfIfTxLinkStateUpds Counter
  wfOspfIfTxLinkStateAcks Counter
  wfOspfIfRxHellos Counter
  wfOspfIfRxDBDescripts Counter
  wfOspfIfRxLinkStateReqs Counter
  wfOspfIfRxLinkStateUpds Counter
  wfOspfIfRxLinkStateAcks Counter
  wfOspfIfDrops Counter

WfOspfVirtIfEntry  
SEQUENCE    
  wfOspfVirtIfDelete INTEGER
  wfOspfVirtIfDisable INTEGER
  wfOspfVirtIfState INTEGER
  wfOspfVirtIfAreaID IpAddress
  wfOspfVirtIfNeighbor IpAddress
  wfOspfVirtIfTransitDelay INTEGER
  wfOspfVirtIfRetransInterval INTEGER
  wfOspfVirtIfHelloInterval INTEGER
  wfOspfVirtIfRtrDeadInterval INTEGER
  wfOspfVirtIfAuthKey OCTET STRING
  wfOspfVirtIfTxHellos Counter
  wfOspfVirtIfTxDBDescripts Counter
  wfOspfVirtIfTxLinkStateReqs Counter
  wfOspfVirtIfTxLinkStateUpds Counter
  wfOspfVirtIfTxLinkStateAcks Counter
  wfOspfVirtIfRxHellos Counter
  wfOspfVirtIfRxDBDescripts Counter
  wfOspfVirtIfRxLinkStateReqs Counter
  wfOspfVirtIfRxLinkStateUpds Counter
  wfOspfVirtIfRxLinkStateAcks Counter
  wfOspfVirtIfDrops Counter

WfOspfNbrEntry  
SEQUENCE    
  wfOspfNbrDelete INTEGER
  wfOspfNbrDisable INTEGER
  wfOspfNbrState INTEGER
  wfOspfNbrIpAddr IpAddress
  wfOspfNbrIfAddr IpAddress
  wfOspfNbrAddressLessIndex INTEGER
  wfOspfNbrRtrId IpAddress
  wfOspfNbrOptions INTEGER
  wfOspfNbrPriority INTEGER
  wfOspfNbrEvents Counter
  wfOspfNbrLSRetransQLen Gauge

WfOspfVirtNbrEntry  
SEQUENCE    
  wfOspfVirtNbrArea IpAddress
  wfOspfVirtNbrRtrId IpAddress
  wfOspfVirtNbrIpAddr IpAddress
  wfOspfVirtNbrOptions INTEGER
  wfOspfVirtNbrState INTEGER
  wfOspfVirtNbrEvents Counter
  wfOspfVirtNbrLSRetransQLen Gauge

WfOspfDynNbrEntry  
SEQUENCE    
  wfOspfDynNbrState INTEGER
  wfOspfDynNbrIpAddr IpAddress
  wfOspfDynNbrIfAddr IpAddress
  wfOspfDynNbrAddressLessIndex INTEGER
  wfOspfDynNbrRtrId IpAddress
  wfOspfDynNbrOptions INTEGER
  wfOspfDynNbrPriority INTEGER
  wfOspfDynNbrEvents Counter
  wfOspfDynNbrLSRetransQLen Gauge

WfIpRfRipImportEntry  
SEQUENCE    
  wfIpRfRipImportCreate INTEGER
  wfIpRfRipImportEnable INTEGER
  wfIpRfRipImportAddress IpAddress
  wfIpRfRipImportMask IpAddress
  wfIpRfRipImportAction INTEGER
  wfIpRfRipImportPreference INTEGER
  wfIpRfRipImportRipGateway IpAddress
  wfIpRfRipImportRipInterface IpAddress

WfIpRfRipExportEntry  
SEQUENCE    
  wfIpRfRipExportCreate INTEGER
  wfIpRfRipExportEnable INTEGER
  wfIpRfRipExportAddress IpAddress
  wfIpRfRipExportMask IpAddress
  wfIpRfRipExportFromProtocol INTEGER
  wfIpRfRipExportAction INTEGER
  wfIpRfRipExportInterface IpAddress
  wfIpRfRipExportRipMetric INTEGER

WfIpRfOspfImportEntry  
SEQUENCE    
  wfIpRfOspfImportCreate INTEGER
  wfIpRfOspfImportEnable INTEGER
  wfIpRfOspfImportAddress IpAddress
  wfIpRfOspfImportMask IpAddress
  wfIpRfOspfImportAction INTEGER
  wfIpRfOspfImportPreference INTEGER
  wfIpRfOspfImportType INTEGER
  wfIpRfOspfImportTag INTEGER

WfIpRfOspfExportEntry  
SEQUENCE    
  wfIpRfOspfExportCreate INTEGER
  wfIpRfOspfExportEnable INTEGER
  wfIpRfOspfExportAddress IpAddress
  wfIpRfOspfExportMask IpAddress
  wfIpRfOspfExportFromProtocol INTEGER
  wfIpRfOspfExportAction INTEGER
  wfIpRfOspfExportType INTEGER
  wfIpRfOspfExportTag INTEGER

WfSipL2Entry  
SEQUENCE    
  wfSipL2Index INTEGER
  wfSipL2ReceivedCounts Counter
  wfSipL2SentCounts Counter
  wfSipHcsOrCRCErrors Counter
  wfSipL2PayloadLengthErrors Counter
  wfSipL2SequenceNumberErrors Counter
  wfSipL2MidCurrentlyActiveErrors Counter
  wfSipL2BomOrSSMsMIDErrors Counter
  wfSipL2EomsMIDErrors Counter

WfSipDs1PlcpEntry  
SEQUENCE    
  wfSipDs1PlcpIndex INTEGER
  wfSipDs1PlcpSEFs Counter
  wfSipDs1PlcpAlarmState INTEGER
  wfSipDs1PlcpUASs Counter

WfSipDs3PlcpEntry  
SEQUENCE    
  wfSipDs3PlcpIndex INTEGER
  wfSipDs3PlcpSEFs Counter
  wfSipDs3PlcpAlarmState INTEGER
  wfSipDs3PlcpUASs Counter

WfSmdsCircuitEntry  
SEQUENCE    
  wfSmdsCircuitDelete INTEGER
  wfSmdsCircuitDisable INTEGER
  wfSmdsCircuitState INTEGER
  wfSmdsCircuitID INTEGER
  wfSmdsCircuitIndivAddr OCTET STRING
  wfSmdsCircuitGroupAddr OCTET STRING
  wfSmdsCircuitArpAddr OCTET STRING
  wfSmdsCircuitDisableHrtbtPoll INTEGER
  wfSmdsCircuitHrtbtPollInterval INTEGER
  wfSmdsCircuitHrtbtPollDownCount INTEGER
  wfSmdsCircuitDisableNetMgmt INTEGER
  wfSmdsCircuitSipL3ReceivedIndividualDAs Counter
  wfSmdsCircuitSipL3ReceivedGAs Counter
  wfSmdsCircuitSipL3SentIndividualDAs Counter
  wfSmdsCircuitSipL3SentGAs Counter
  wfSmdsCircuitSipL3VersionSupport INTEGER

WfSnmpCommEntry  
SEQUENCE    
  wfSnmpCommDelete INTEGER
  wfSnmpCommIndex INTEGER
  wfSnmpCommName DisplayString
  wfSnmpCommAccess INTEGER

WfSnmpMgrEntry  
SEQUENCE    
  wfSnmpMgrDelete INTEGER
  wfSnmpMgrCommIndex INTEGER
  wfSnmpMgrAddress IpAddress
  wfSnmpMgrName DisplayString
  wfSnmpMgrTrapPort INTEGER
  wfSnmpMgrTraps INTEGER

WfBrStpInterfaceEntry  
SEQUENCE    
  wfBrStpInterfaceDelete INTEGER
  wfBrStpInterfaceEnable INTEGER
  wfBrStpInterfaceCircuit INTEGER
  wfBrStpInterfacePriority INTEGER
  wfBrStpInterfaceState INTEGER
  wfBrStpInterfaceMultiCastAddr OCTET STRING
  wfBrStpInterfacePathCost INTEGER
  wfBrStpInterfaceDesignatedRoot OCTET STRING
  wfBrStpInterfaceDesignatedCost INTEGER
  wfBrStpInterfaceDesignatedBridge OCTET STRING
  wfBrStpInterfaceDesignatedPort INTEGER
  wfBrStpInterfaceForwardTransitions Counter
  wfBrStpInterfacePktsXmitd Counter
  wfBrStpInterfacePktsRcvd Counter

WfBrSrInterfaceEntry  
SEQUENCE    
  wfBrSrInterfaceDelete INTEGER
  wfBrSrInterfaceDisable INTEGER
  wfBrSrInterfaceState INTEGER
  wfBrSrInterfaceCircuit INTEGER
  wfBrSrInterfaceMaxRds INTEGER
  wfBrSrInterfaceRing INTEGER
  wfBrSrInterfaceBlockOutSte INTEGER
  wfBrSrInterfaceBlockInSte INTEGER
  wfBrSrInterfaceBlockIp INTEGER
  wfBrSrInterfaceIpAddress IpAddress
  wfBrSrInterfaceInFrames Counter
  wfBrSrInterfaceOutFrames Counter
  wfBrSrInterfaceOutIpFrames Counter
  wfBrSrInterfaceDropInvalidRcs Counter
  wfBrSrInterfaceDropInvalidRings Counter
  wfBrSrInterfaceDropSrfs Counter

WfBrSrBridgeEntry  
SEQUENCE    
  wfBrSrBridgeDelete INTEGER
  wfBrSrBridgeId INTEGER

WfBrSrIpExplorerEntry  
SEQUENCE    
  wfBrSrIpExplorerDelete INTEGER
  wfBrSrIpExplorerAddr IpAddress

WfBrSrIpEncapsEntry  
SEQUENCE    
  wfBrSrIpEncapsRing INTEGER
  wfBrSrIpEncapsIpAddress IpAddress
  wfBrSrIpEncapsStatus INTEGER

WfBrSrTrafficFilterEntry  
SEQUENCE    
  wfBrSrTrafficFilterCreate INTEGER
  wfBrSrTrafficFilterEnable INTEGER
  wfBrSrTrafficFilterStatus INTEGER
  wfBrSrTrafficFilterCounter Counter
  wfBrSrTrafficFilterDefinition OCTET STRING
  wfBrSrTrafficFilterReserved INTEGER
  wfBrSrTrafficFilterCircuit INTEGER
  wfBrSrTrafficFilterRuleNumber INTEGER
  wfBrSrTrafficFilterFragment INTEGER

WfBrSrEsRifEntry  
SEQUENCE    
  wfBrSrEsRifCircuit INTEGER
  wfBrSrEsRifProtocol OCTET STRING
  wfBrSrEsRifMacAddr OCTET STRING
  wfBrSrEsRifRoute OCTET STRING

WfSyncEntry  
SEQUENCE    
  wfSyncDelete INTEGER
  wfSyncDisable INTEGER
  wfSyncState INTEGER
  wfSyncSlot INTEGER
  wfSyncConnector INTEGER
  wfSyncCct INTEGER
  wfSyncBofl INTEGER
  wfSyncBoflTmo INTEGER
  wfSyncMtu INTEGER
  wfSyncMadr OCTET STRING
  wfSyncPromiscuous INTEGER
  wfSyncXid INTEGER
  wfSyncClkSource INTEGER
  wfSyncClkSpeed INTEGER
  wfSyncSignalMode INTEGER
  wfSyncRtsEnable INTEGER
  wfSyncBurstCount INTEGER
  wfSyncService INTEGER
  wfSyncRetryCount INTEGER
  wfSyncLinkIdleTimer INTEGER
  wfSyncRetryTimer INTEGER
  wfSyncExtendedAddress INTEGER
  wfSyncExtendedAddressForce INTEGER
  wfSyncExtendedControl INTEGER
  wfSyncExtendedControlForce INTEGER
  wfSyncConnectAttempts INTEGER
  wfSyncWindowSizeTx INTEGER
  wfSyncWindowSizeTxExtc INTEGER
  wfSyncMinFrameSpace INTEGER
  wfSyncLocalAddress INTEGER
  wfSyncRemoteAddress INTEGER
  wfSyncPassThruLocalMadr OCTET STRING
  wfSyncPassThruRemoteMadr OCTET STRING
  wfSyncWanProtocol INTEGER
  wfSyncCrcSize INTEGER
  wfSyncRxOctets Counter
  wfSyncRxFrames Counter
  wfSyncTxOctets Counter
  wfSyncTxFrames Counter
  wfSyncRxErrors Counter
  wfSyncTxErrors Counter
  wfSyncLackRescRx Counter
  wfSyncLackRescTx Counter
  wfSyncUnderFlowTx Counter
  wfSyncRejectsTx Counter
  wfSyncRejectsRx Counter
  wfSyncOverFlowRx Counter
  wfSyncFramesIncompRx Counter
  wfSyncBadFramesRx Counter
  wfSyncFrameRejectsRx Counter
  wfSyncRuntsRx Counter
  wfSyncT1Timeouts Counter
  wfSyncMemoryErrors Counter
  wfSyncMediaType INTEGER

WfT1Entry  
SEQUENCE    
  wfT1Delete INTEGER
  wfT1Disable INTEGER
  wfT1State INTEGER
  wfT1Slot INTEGER
  wfT1Connector INTEGER
  wfT1Madr OCTET STRING
  wfT1FrameType INTEGER
  wfT1LineBuildout INTEGER
  wfT1B8ZSSupport INTEGER
  wfT1ClockMode INTEGER
  wfT1MiniDacs DisplayString
  wfT1BipolarVios Counter
  wfT1FrameBitErrs Counter
  wfT1OutOfFrameErrs Counter
  wfT1SuperFrameErrs Counter
  wfT1RcvYelAlarms Counter
  wfT1RcvCarrierLoss Counter
  wfT1RcvRedAlarms Counter

WfTokenRingEntry  
SEQUENCE    
  wfTokenRingDelete INTEGER
  wfTokenRingDisable INTEGER
  wfTokenRingState INTEGER
  wfTokenRingSlot INTEGER
  wfTokenRingConnector INTEGER
  wfTokenRingCct INTEGER
  wfTokenRingMtu INTEGER
  wfTokenRingMadr OCTET STRING
  wfTokenRingCfgMadr OCTET STRING
  wfTokenRingMadrSelect INTEGER
  wfTokenRingSpeed INTEGER
  wfTokenRingEarlyTokenRelease INTEGER
  wfTokenRingStatus INTEGER
  wfTokenRingOpenState INTEGER
  wfTokenRingOpenStatus INTEGER
  wfTokenRingUpStream OCTET STRING
  wfTokenRingRxOctets Counter
  wfTokenRingRxFrames Counter
  wfTokenRingTxOctets Counter
  wfTokenRingTxFrames Counter
  wfTokenRingInDiscards Counter
  wfTokenRingInErrors Counter
  wfTokenRingOutDiscards Counter
  wfTokenRingOutErrors Counter
  wfTokenRingTxClipFrames Counter
  wfTokenRingRxReplenMisses Counter
  wfTokenRingSignalLosses Counter
  wfTokenRingHardErrors Counter
  wfTokenRingSoftErrors Counter
  wfTokenRingTransmitBeacons Counter
  wfTokenRingLobeWireFaults Counter
  wfTokenRingAutoRemovalErrors Counter
  wfTokenRingRequestRemoves Counter
  wfTokenRingCounterOverflows Counter
  wfTokenRingSingleStations Counter
  wfTokenRingRingRecoveries Counter
  wfTokenRingAdapterChecks Counter
  wfTokenRingFirstAdapterCheckCode INTEGER
  wfTokenRingLastAdapterCheckCode INTEGER
  wfTokenRingLineErrors Counter
  wfTokenRingBurstErrors Counter
  wfTokenRingAriFciErrors Counter
  wfTokenRingLostFrameErrors Counter
  wfTokenRingRxCongestionErrors Counter
  wfTokenRingFrameCopiedErrors Counter
  wfTokenRingTokenErrors Counter
  wfTokenRingDmaBusErrors Counter
  wfTokenRingDmaParityErrors Counter
  wfTokenRingSrbNotFreeCmdAborts Counter
  wfTokenRingRxProcessings Counter
  wfTokenRingTxProcessings Counter
  wfTokenRingTxCmplProcessings Counter
  wfTokenRingRxTimeouts Counter
  wfTokenRingCmdTimeouts Counter
  wfTokenRingRxHostIntErrors Counter
  wfTokenRingRxTxBufferSize INTEGER

WfVinesRtpNbrEntry  
SEQUENCE    
  wfVinesRtpNbrNetId Counter
  wfVinesRtpNbrSubNetId INTEGER
  wfVinesRtpNbrType INTEGER
  wfVinesRtpNbrIfType INTEGER
  wfVinesRtpNbrRemAdr OCTET STRING
  wfVinesRtpNbrLocAdr OCTET STRING
  wfVinesRtpNbrLocSlot INTEGER
  wfVinesRtpNbrLocLine INTEGER
  wfVinesRtpNbrSvrName OCTET STRING
  wfVinesRtpNbrCost INTEGER

WfVinesRtpRtEntry  
SEQUENCE    
  wfVinesRtpRtNetid Counter
  wfVinesRtpRtMetric INTEGER
  wfVinesRtpRtIdle INTEGER
  wfVinesRtpRtGateNetid Counter
  wfVinesRtpRtSvrName OCTET STRING
  wfVinesRtpRtGateSvrName OCTET STRING

WfVinesIfEntry  
SEQUENCE    
  wfVinesIfDelete INTEGER
  wfVinesIfDisable INTEGER
  wfVinesIfState INTEGER
  wfVinesIfSlot INTEGER
  wfVinesIfLine INTEGER
  wfVinesIfCct INTEGER
  wfVinesIfSession INTEGER
  wfVinesIfType INTEGER
  wfVinesIfDescr OCTET STRING
  wfVinesIfAdr OCTET STRING
  wfVinesIfDodIpDisable INTEGER
  wfVinesIfArpDisable INTEGER
  wfVinesIfTrEndStation INTEGER
  wfVinesIfInPkts Counter
  wfVinesIfInErrs Counter
  wfVinesIfOutPkts Counter
  wfVinesIfOutErrs Counter
  wfVinesIfInMsgs Counter
  wfVinesIfMux INTEGER
  wfVinesIfFwdDrops Counter
  wfVinesIfZeroHopDrops Counter
  wfVinesIfIcpInErrorNotifs Counter
  wfVinesIfIcpInMetricNotifs Counter
  wfVinesIfIcpInErrors Counter
  wfVinesIfIcpOutErrorNotifs Counter
  wfVinesIfIcpOutMetricNotifs Counter
  wfVinesIfArpInQueries Counter
  wfVinesIfArpInAssgReqs Counter
  wfVinesIfArpInErrors Counter
  wfVinesIfArpOutServRsps Counter
  wfVinesIfArpOutAssgRsps Counter
  wfVinesIfInRedirects Counter
  wfVinesIfOutRedirects Counter
  wfVinesIfEchoInPkts Counter
  wfVinesIfEchoOutPkts Counter
  wfVinesIfReassFails Counter
  wfVinesIfRemClientPrivDisable INTEGER

WfVinesIfX25VCEntry  
SEQUENCE    
  wfVinesIfX25VCSlot INTEGER
  wfVinesIfX25VCLine INTEGER
  wfVinesIfX25VCCct INTEGER
  wfVinesIfX25VCSession INTEGER
  wfVinesIfX25VCTotIn Counter
  wfVinesIfX25VCTotOut Counter
  wfVinesIfX25VCInErrs Counter
  wfVinesIfX25VCOutErrs Counter
  wfVinesIfX25VCPktsOut Counter
  wfVinesIfX25VCPktsAwaitAck INTEGER
  wfVinesIfX25VCBytesOut Counter
  wfVinesIfX25VCBytesAwaitAck INTEGER
  wfVinesIfX25VCPktsIn Counter
  wfVinesIfX25VCBytesIn Counter
  wfVinesIfX25VCResetsIn Counter
  wfVinesIfX25VCResetsOut Counter

WfVinesTrafficFilterEntry  
SEQUENCE    
  wfVinesTrafficFilterCreate INTEGER
  wfVinesTrafficFilterEnable INTEGER
  wfVinesTrafficFilterStatus INTEGER
  wfVinesTrafficFilterCounter Counter
  wfVinesTrafficFilterDefinition OCTET STRING
  wfVinesTrafficFilterReserved INTEGER
  wfVinesTrafficFilterCircuit INTEGER
  wfVinesTrafficFilterRuleNumber INTEGER
  wfVinesTrafficFilterFragment INTEGER

WfVinesNameEntry  
SEQUENCE    
  wfVinesNameDelete INTEGER
  wfVinesNameDisable INTEGER
  wfVinesNameNetid Counter
  wfVinesNameHost DisplayString
  wfVinesNameSubNetid INTEGER

WfXnsBaseRtEntry  
SEQUENCE    
  wfXnsBaseRouteDest OCTET STRING
  wfXnsBaseRouteIfIndex INTEGER
  wfXnsBaseRouteMetric INTEGER
  wfXnsBaseRouteNextHopNetwork OCTET STRING
  wfXnsBaseRouteNextHopHost OCTET STRING
  wfXnsBaseRouteType INTEGER
  wfXnsBaseRouteProto INTEGER
  wfXnsBaseRouteAge INTEGER
  wfXnsBaseRouteInfo OCTET STRING

WfXnsInterfaceEntry  
SEQUENCE    
  wfXnsInterfaceIndex INTEGER
  wfXnsInterfaceDelete INTEGER
  wfXnsInterfaceDisable INTEGER
  wfXnsInterfaceState INTEGER
  wfXnsInterfaceCircuit INTEGER
  wfXnsInterfaceNetworkNumber OCTET STRING
  wfXnsInterfaceCost INTEGER
  wfXnsInterfaceXsumOn INTEGER
  wfXnsInterfaceEncaps INTEGER
  wfXnsInterfaceMacAddress OCTET STRING
  wfXnsInterfaceSMDSGroupAddress OCTET STRING
  wfXnsInterfaceMaxInfo INTEGER
  wfXnsInterfaceExtServer INTEGER
  wfXnsInterfaceExServNetwork OCTET STRING
  wfXnsInterfaceExServHostId OCTET STRING
  wfXnsInterfaceExServPktType OCTET STRING
  wfXnsInterfaceExServSockNm OCTET STRING
  wfXnsInterfaceInReceives Counter
  wfXnsInterfaceInHdrErrors Counter
  wfXnsInterfaceInAddrErrors Counter
  wfXnsInterfaceForwDatagrams Counter
  wfXnsInterfaceInUnknownProtos Counter
  wfXnsInterfaceInDiscards Counter
  wfXnsInterfaceInDelivers Counter
  wfXnsInterfaceOutRequests Counter
  wfXnsInterfaceOutDiscards Counter
  wfXnsInterfaceOutNoRoutes Counter
  wfXnsInterfaceFRBcast OCTET STRING
  wfXnsInterfaceFRMcast OCTET STRING

WfXnsRipIntfEntry  
SEQUENCE    
  wfXnsRipInterfaceDelete INTEGER
  wfXnsRipInterfaceDisable INTEGER
  wfXnsRipInterfaceState INTEGER
  wfXnsRipInterfaceIndex OCTET STRING
  wfXnsRipInterfaceSupply INTEGER
  wfXnsRipInterfaceListen INTEGER

WfXnsAdjacentHostEntry  
SEQUENCE    
  wfXnsAhDelete INTEGER
  wfXnsAhDisable INTEGER
  wfXnsAhTargHostNetwork OCTET STRING
  wfXnsAhTargHostId OCTET STRING
  wfXnsAhNextHopIntf OCTET STRING
  wfXnsAhDlci OCTET STRING

WfXnsStaticRouteEntry  
SEQUENCE    
  wfXnsSrDelete INTEGER
  wfXnsSrDisable INTEGER
  wfXnsSrTargNetwork OCTET STRING
  wfXnsSrCost INTEGER
  wfXnsSrNextHopNetwork OCTET STRING
  wfXnsSrNextHopHost OCTET STRING
  wfXnsSrTargNetworkRt INTEGER

WfXnsTrafficFilterEntry  
SEQUENCE    
  wfXnsTrafficFilterCreate INTEGER
  wfXnsTrafficFilterEnable INTEGER
  wfXnsTrafficFilterStatus INTEGER
  wfXnsTrafficFilterCounter Counter
  wfXnsTrafficFilterDefinition Opaque
  wfXnsTrafficFilterReserved INTEGER
  wfXnsTrafficFilterInterface OCTET STRING
  wfXnsTrafficFilterCircuit INTEGER
  wfXnsTrafficFilterRuleNumber INTEGER
  wfXnsTrafficFilterFragment INTEGER

Defined Values

wellfleet 1.3.6.1.4.1.18
OBJECT IDENTIFIER    

wfSwSeries7 1.3.6.1.4.1.18.3
OBJECT IDENTIFIER    

wfHardwareConfig 1.3.6.1.4.1.18.3.1
OBJECT IDENTIFIER    

wfSoftwareConfig 1.3.6.1.4.1.18.3.2
OBJECT IDENTIFIER    

wfSystem 1.3.6.1.4.1.18.3.3
OBJECT IDENTIFIER    

wfServices 1.3.6.1.4.1.18.3.3.2
OBJECT IDENTIFIER    

wfGameGroup 1.3.6.1.4.1.18.3.3.2.5
OBJECT IDENTIFIER    

wfLine 1.3.6.1.4.1.18.3.4
OBJECT IDENTIFIER    

wfHwFGroup 1.3.6.1.4.1.18.3.4.6
OBJECT IDENTIFIER    

wfDs1Group 1.3.6.1.4.1.18.3.4.12
OBJECT IDENTIFIER    

wfDs3Group 1.3.6.1.4.1.18.3.4.13
OBJECT IDENTIFIER    

wfSipGroup 1.3.6.1.4.1.18.3.4.14
OBJECT IDENTIFIER    

wfSipPlcpGroup 1.3.6.1.4.1.18.3.4.14.2
OBJECT IDENTIFIER    

wfFddiGroup 1.3.6.1.4.1.18.3.4.15
OBJECT IDENTIFIER    

wfFddiSmtGroup 1.3.6.1.4.1.18.3.4.15.1
OBJECT IDENTIFIER    

wfFddiMacGroup 1.3.6.1.4.1.18.3.4.15.2
OBJECT IDENTIFIER    

wfFddiPathGroup 1.3.6.1.4.1.18.3.4.15.3
OBJECT IDENTIFIER    

wfFddiPortGroup 1.3.6.1.4.1.18.3.4.15.4
OBJECT IDENTIFIER    

wfApplication 1.3.6.1.4.1.18.3.5
OBJECT IDENTIFIER    


wfBridgeGroup 1.3.6.1.4.1.18.3.5.1.1
OBJECT IDENTIFIER    

wfBrLearning 1.3.6.1.4.1.18.3.5.1.1.1
OBJECT IDENTIFIER    

wfBrSourceRouting 1.3.6.1.4.1.18.3.5.1.1.2
OBJECT IDENTIFIER    

wfSpanningTree 1.3.6.1.4.1.18.3.5.1.2
OBJECT IDENTIFIER    

wfIfGroup 1.3.6.1.4.1.18.3.5.1.3
OBJECT IDENTIFIER    

wfCircuitOptsGroup 1.3.6.1.4.1.18.3.5.1.4
OBJECT IDENTIFIER    

wfDecGroup 1.3.6.1.4.1.18.3.5.2
OBJECT IDENTIFIER    

wfInternet 1.3.6.1.4.1.18.3.5.3
OBJECT IDENTIFIER    

wfArpGroup 1.3.6.1.4.1.18.3.5.3.1
OBJECT IDENTIFIER    

wfIpRouting 1.3.6.1.4.1.18.3.5.3.2
OBJECT IDENTIFIER    

wfIpGroup 1.3.6.1.4.1.18.3.5.3.2.1
OBJECT IDENTIFIER    

wfRipGroup 1.3.6.1.4.1.18.3.5.3.2.2
OBJECT IDENTIFIER    

wfOspfGroup 1.3.6.1.4.1.18.3.5.3.2.3
OBJECT IDENTIFIER    

wfEgpGroup 1.3.6.1.4.1.18.3.5.3.2.4
OBJECT IDENTIFIER    

wfBgpGroup 1.3.6.1.4.1.18.3.5.3.2.5
OBJECT IDENTIFIER    

wfTcpGroup 1.3.6.1.4.1.18.3.5.3.3
OBJECT IDENTIFIER    

wfUdpGroup 1.3.6.1.4.1.18.3.5.3.4
OBJECT IDENTIFIER    

wfSnmpGroup 1.3.6.1.4.1.18.3.5.3.5
OBJECT IDENTIFIER    

wfTelnetGroup 1.3.6.1.4.1.18.3.5.3.7
OBJECT IDENTIFIER    

wfBootpGroup 1.3.6.1.4.1.18.3.5.3.8
OBJECT IDENTIFIER    

wfAppletalkGroup 1.3.6.1.4.1.18.3.5.4
OBJECT IDENTIFIER    

wfIpxGroup 1.3.6.1.4.1.18.3.5.5
OBJECT IDENTIFIER    

wfOsiGroup 1.3.6.1.4.1.18.3.5.6
OBJECT IDENTIFIER    

wfVinesGroup 1.3.6.1.4.1.18.3.5.8
OBJECT IDENTIFIER    

wfWanGroup 1.3.6.1.4.1.18.3.5.9
OBJECT IDENTIFIER    

wfFrameRelayGroup 1.3.6.1.4.1.18.3.5.9.1
OBJECT IDENTIFIER    

wfPppGroup 1.3.6.1.4.1.18.3.5.9.2
OBJECT IDENTIFIER    

wfX25Group 1.3.6.1.4.1.18.3.5.9.4
OBJECT IDENTIFIER    

wfAtmGroup 1.3.6.1.4.1.18.3.5.9.5
OBJECT IDENTIFIER    

wfXnsGroup 1.3.6.1.4.1.18.3.5.10
OBJECT IDENTIFIER    

wfTestGroup 1.3.6.1.4.1.18.3.5.11
OBJECT IDENTIFIER    

wfAppleBase 1.3.6.1.4.1.18.3.5.4.1
OBJECT IDENTIFIER    

wfAppleBaseDelete 1.3.6.1.4.1.18.3.5.4.1.1
Create/Delete parameter for determining whether or not AppleTalk is configured on this slot.
Status: mandatory Access: read-write
OBJECT-TYPE    
  INTEGER created(1), deleted(2)  

wfAppleBaseDisable 1.3.6.1.4.1.18.3.5.4.1.2
Enable/Disable parameter for determining whether or not to startup AppleTalk.
Status: mandatory Access: read-write
OBJECT-TYPE    
  INTEGER enabled(1), disabled(2)  

wfAppleBaseState 1.3.6.1.4.1.18.3.5.4.1.3
This parameter relfects the current state of AppleTalk.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER up(1), down(2), init(3), notpres(4)  

wfAppleBaseDebugLevel 1.3.6.1.4.1.18.3.5.4.1.4
Appletalk has control of what debug and info messages are printed.
Status: mandatory Access: read-write
OBJECT-TYPE    
  INTEGER  

wfAppleBaseDdpQueLen 1.3.6.1.4.1.18.3.5.4.1.5
Queue clipping is done on all packets destined for the port. This is the length of the queue.
Status: mandatory Access: read-write
OBJECT-TYPE    
  INTEGER default(20)  

wfAppleBaseHomedPort 1.3.6.1.4.1.18.3.5.4.1.6
The circuit number of the port on which NBP will register this router.
Status: mandatory Access: read-write
OBJECT-TYPE    
  INTEGER  

wfAppleBaseTotalNets 1.3.6.1.4.1.18.3.5.4.1.7
The circuit number of the port on which NBP will register this router.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER  

wfAppleBaseTotalZones 1.3.6.1.4.1.18.3.5.4.1.8
The circuit number of the port on which NBP will register this router.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER  

wfAppleRtmpTable 1.3.6.1.4.1.18.3.5.4.2
The table of elements of AppleTalk's routing RTMP table
Status: mandatory Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    WfAppleRtmpEntry

wfAppleRtmpEntry 1.3.6.1.4.1.18.3.5.4.2.1
An entry in the Routing table
Status: mandatory Access: not-accessible
OBJECT-TYPE    
  WfAppleRtmpEntry  

wfAppleRtmpNetStart 1.3.6.1.4.1.18.3.5.4.2.1.1
The destinatination network range of this route to which this entry pertains. The route is considered the best route to that network. There wil only be one route to a single destination. The address will be in the form of [network min - network max].
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER  

wfAppleRtmpNetEnd 1.3.6.1.4.1.18.3.5.4.2.1.2
The network max in the destination network range to which the routing entry pertains.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER  

wfAppleRtmpPort 1.3.6.1.4.1.18.3.5.4.2.1.3
The index value which uniquely identifies the local interface through which the next hop of this route should be reached. The interface identified by a particular value of this index is the same interface as identified by the same value of ifIndex.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER  

wfAppleRtmpHops 1.3.6.1.4.1.18.3.5.4.2.1.4
The routing metric to get to this destination network. The measurement is in terms of hops.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER  

wfAppleRtmpNextHopNet 1.3.6.1.4.1.18.3.5.4.2.1.5
The AppleTalk net of the next hop router for this route.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER  

wfAppleRtmpNextHopNode 1.3.6.1.4.1.18.3.5.4.2.1.6
The AppleTalk node of the next hop router for this route.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER  

wfAppleRtmpState 1.3.6.1.4.1.18.3.5.4.2.1.7
The state of this routing entry: (G)ood, (S)uspect, (GB) GoingBad, or (B)ad. Setting this object to the value bad(4) has the effect of invalidating the corresponding entry in the RTMP table.
Status: mandatory Access: read-write
OBJECT-TYPE    
  INTEGER good(1), suspect(2), goingbad(3), bad(4)  

wfApplePortTable 1.3.6.1.4.1.18.3.5.4.3
The port descriptor table that describes the configuration parameters for this port of the AppleTalk Router.
Status: mandatory Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    WfApplePortEntry

wfApplePortEntry 1.3.6.1.4.1.18.3.5.4.3.1
An entry in the Port Descriptor table
Status: mandatory Access: not-accessible
OBJECT-TYPE    
  WfApplePortEntry  

wfApplePortDelete 1.3.6.1.4.1.18.3.5.4.3.1.1
Create/Delete parameter. Users perform an SNMP SET operation on this object to create/delete an AppleTalk interface. The default is create.
Status: mandatory Access: read-write
OBJECT-TYPE    
  INTEGER created(1), deleted(2)  

wfApplePortDisable 1.3.6.1.4.1.18.3.5.4.3.1.2
Enable/Disable parameter. Users perforn an SNMP SET operation on this object to enable/disable an AppleTalk interface. Default is enabled.
Status: mandatory Access: read-write
OBJECT-TYPE    
  INTEGER enabled(1), disabled(2)  

wfApplePortCircuit 1.3.6.1.4.1.18.3.5.4.3.1.3
The circuit number for this interface
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER  

wfApplePortState 1.3.6.1.4.1.18.3.5.4.3.1.4
The current state of the AppleTalk port.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER up(1), down(2)  

wfApplePortType 1.3.6.1.4.1.18.3.5.4.3.1.5
The type for the port
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER  

wfApplePortCksumDisable 1.3.6.1.4.1.18.3.5.4.3.1.6
Flag to enable/disable the calculation of the DDP checksum for packets sourced by the router over this interface. This value has no effect on incoming packets.
Status: mandatory Access: read-write
OBJECT-TYPE    
  INTEGER enabled(1), disabled(2)  

wfApplePortTrEndStation 1.3.6.1.4.1.18.3.5.4.3.1.7
When an interface is running token ring this attribute allows for end station source routing. If the interface is not running token ring the attribute has no meaning.
Status: mandatory Access: read-write
OBJECT-TYPE    
  INTEGER enabled(1), disabled(2)  

wfApplePortGniForever 1.3.6.1.4.1.18.3.5.4.3.1.8
During initialization default behavior is to send 3 GetNetInfos and then shut down the port. This will send GetNetInfos forever.
Status: mandatory Access: read-write
OBJECT-TYPE    
  INTEGER  

wfApplePortAarpFlush 1.3.6.1.4.1.18.3.5.4.3.1.9
Setting this to a non-null value causes the aarp table to be emptied of all entries.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER  

wfApplePortMacAddress 1.3.6.1.4.1.18.3.5.4.3.1.10
Configured mac address
Status: mandatory Access: read-write
OBJECT-TYPE    
  OCTET STRING  

wfApplePortNodeId 1.3.6.1.4.1.18.3.5.4.3.1.11
The AppleTalk node id configured for this port/interface.
Status: mandatory Access: read-write
OBJECT-TYPE    
  INTEGER  

wfApplePortNetwork 1.3.6.1.4.1.18.3.5.4.3.1.12
The Network NUMBER for this interface/port.
Status: mandatory Access: read-write
OBJECT-TYPE    
  INTEGER  

wfApplePortNetStart 1.3.6.1.4.1.18.3.5.4.3.1.13
The Network start value in the network range for this interface/port.
Status: mandatory Access: read-write
OBJECT-TYPE    
  INTEGER  

wfApplePortNetEnd 1.3.6.1.4.1.18.3.5.4.3.1.14
The Network end value in the network range for this interface/port.
Status: mandatory Access: read-write
OBJECT-TYPE    
  INTEGER  

wfApplePortDfltZone 1.3.6.1.4.1.18.3.5.4.3.1.15
The default zone name for this network range/ interface.
Status: mandatory Access: read-write
OBJECT-TYPE    
  DisplayString  

wfApplePortCurMacAddress 1.3.6.1.4.1.18.3.5.4.3.1.16
Mac Address used
Status: mandatory Access: read-only
OBJECT-TYPE    
  OCTET STRING  

wfApplePortCurNodeId 1.3.6.1.4.1.18.3.5.4.3.1.17
The AppleTalk node id of this port
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER  

wfApplePortCurNetwork 1.3.6.1.4.1.18.3.5.4.3.1.18
The network number for this port.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER  

wfApplePortCurNetStart 1.3.6.1.4.1.18.3.5.4.3.1.19
The Network start value in the network range for this port.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER  

wfApplePortCurNetEnd 1.3.6.1.4.1.18.3.5.4.3.1.20
The Network end value in the network range for this port.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER  

wfApplePortCurDfltZone 1.3.6.1.4.1.18.3.5.4.3.1.21
The default zone name for this port
Status: mandatory Access: read-only
OBJECT-TYPE    
  DisplayString  

wfApplePortAarpProbeRxs 1.3.6.1.4.1.18.3.5.4.3.1.22
The number of AARP Probe packets received on this interface.
Status: mandatory Access: read-only
OBJECT-TYPE    
  Counter  

wfApplePortAarpProbeTxs 1.3.6.1.4.1.18.3.5.4.3.1.23
The number of AARP Probe packets transmitted on this interface.
Status: mandatory Access: read-only
OBJECT-TYPE    
  Counter  

wfApplePortAarpReqRxs 1.3.6.1.4.1.18.3.5.4.3.1.24
The number of AARP Request packets received on this interface.
Status: mandatory Access: read-only
OBJECT-TYPE    
  Counter  

wfApplePortAarpReqTxs 1.3.6.1.4.1.18.3.5.4.3.1.25
The number of AARP Request packets transmitted on this interface.
Status: mandatory Access: read-only
OBJECT-TYPE    
  Counter  

wfApplePortAarpRspRxs 1.3.6.1.4.1.18.3.5.4.3.1.26
The number of AARP Response packets received on this interface.
Status: mandatory Access: read-only
OBJECT-TYPE    
  Counter  

wfApplePortAarpRspTxs 1.3.6.1.4.1.18.3.5.4.3.1.27
The number of AARP Response packets transmitted on this interface.
Status: mandatory Access: read-only
OBJECT-TYPE    
  Counter  

wfApplePortDdpOutRequests 1.3.6.1.4.1.18.3.5.4.3.1.28
The total number of DDP datagrams which were supplied to DDP by local DDP clients in requests for transmission. Note that this counter does not include any datagrams counted in ddpForwRequests.
Status: mandatory Access: read-only
OBJECT-TYPE    
  Counter  

wfApplePortDdpInReceives 1.3.6.1.4.1.18.3.5.4.3.1.29
The total number of input datagrams received by DDP, including those received in error.
Status: mandatory Access: read-only
OBJECT-TYPE    
  Counter  

wfApplePortDdpInLocalDatagrams 1.3.6.1.4.1.18.3.5.4.3.1.30
The total number of input DDP datagrams for which this entity was their final DDP destination.
Status: mandatory Access: read-only
OBJECT-TYPE    
  Counter  

wfApplePortDdpNoProtocolHandlers 1.3.6.1.4.1.18.3.5.4.3.1.31
The total number of DDP datagrams addressed to this entity that were addressed to an upper layer protocol for which no protocol handler existed.
Status: mandatory Access: read-only
OBJECT-TYPE    
  Counter  

wfApplePortDdpTooShortErrors 1.3.6.1.4.1.18.3.5.4.3.1.32
The total number of input DDP datagrams dropped because the received data length was less than the data length specified in the DDP header or the received data length was less than the length of the expected DDP header.
Status: mandatory Access: read-only
OBJECT-TYPE    
  Counter  

wfApplePortDdpTooLongErrors 1.3.6.1.4.1.18.3.5.4.3.1.33
The total number of input DDP datagrams dropped because the received data length was greater than the data length specified in the DDP header or because they exceeded the maximum DDP datagram size.
Status: mandatory Access: read-only
OBJECT-TYPE    
  Counter  

wfApplePortDdpChecksumErrors 1.3.6.1.4.1.18.3.5.4.3.1.34
The total number of input DDP datagrams for which this DDP entity was their final destination, and which were dropped because of a checksum error.
Status: mandatory Access: read-only
OBJECT-TYPE    
  Counter  

wfApplePortDdpForwRequests 1.3.6.1.4.1.18.3.5.4.3.1.35
The number of input datagrams for which this entity was not their final DDP destination, as a result of which an attempt was made to find a route to forward them to that final destination.
Status: mandatory Access: read-only
OBJECT-TYPE    
  Counter  

wfApplePortDdpOutNoRoutes 1.3.6.1.4.1.18.3.5.4.3.1.36
The total number of DDP datagrams dropped because a route could not be found to their final destination.
Status: mandatory Access: read-only
OBJECT-TYPE    
  Counter  

wfApplePortDdpBroadcastErrors 1.3.6.1.4.1.18.3.5.4.3.1.37
The total number of input DDP datagrams dropped because this entity was not their final destination and they were addressed to the link level broadcast.
Status: mandatory Access: read-only
OBJECT-TYPE    
  Counter  

wfApplePortDdpHopCountErrors 1.3.6.1.4.1.18.3.5.4.3.1.38
The total number of input DDP datagrams dropped because this entity was not their final destination and their hop count would exceed 15.
Status: mandatory Access: read-only
OBJECT-TYPE    
  Counter  

wfApplePortRtmpInDataPkts 1.3.6.1.4.1.18.3.5.4.3.1.39
A count of the number of good RTMP data packets received by this entity.
Status: mandatory Access: read-only
OBJECT-TYPE    
  Counter  

wfApplePortRtmpOutDataPkts 1.3.6.1.4.1.18.3.5.4.3.1.40
A count of the number of RTMP packets sent by this entity.
Status: mandatory Access: read-only
OBJECT-TYPE    
  Counter  

wfApplePortRtmpInRequestPkts 1.3.6.1.4.1.18.3.5.4.3.1.41
A count of the number of good RTMP Request packets received by this entity.
Status: mandatory Access: read-only
OBJECT-TYPE    
  Counter  

wfApplePortRtmpNextIREqualChanges 1.3.6.1.4.1.18.3.5.4.3.1.42
A count of the number of times RTMP changes the Next Internet Router in a routing entry because the hop count advertised in a routing tuple was equal to the current hop count for a particular network.
Status: mandatory Access: read-only
OBJECT-TYPE    
  Counter  

wfApplePortRtmpNextIRLessChanges 1.3.6.1.4.1.18.3.5.4.3.1.43
A count of the number of times RTMP changes the Next Internet Router in a routing entry because the hop count advertised in a routing tuple was less than the current hop count for a particular network.
Status: mandatory Access: read-only
OBJECT-TYPE    
  Counter  

wfApplePortRtmpRouteDeletes 1.3.6.1.4.1.18.3.5.4.3.1.44
A count of the number of times RTMP deletes a route because it was aged out of the table. This can help to detect routing problems.
Status: mandatory Access: read-only
OBJECT-TYPE    
  Counter  

wfApplePortRtmpNetworkMismatchErrors 1.3.6.1.4.1.18.3.5.4.3.1.45
The number of times RTMP receives a Data packet from a router who claims to be on a different network than that configured for the receiving port. This can help to detect configuration errors.
Status: mandatory Access: read-only
OBJECT-TYPE    
  Counter  

wfApplePortRtmpRoutingTableOverflows 1.3.6.1.4.1.18.3.5.4.3.1.46
The number of times RTMP attempted to add a route to the RTMP table but failed due to overflow.
Status: mandatory Access: read-only
OBJECT-TYPE    
  Counter  

wfApplePortZipInZipQueries 1.3.6.1.4.1.18.3.5.4.3.1.47
The number of ZIP Queries received by this entity.
Status: mandatory Access: read-only
OBJECT-TYPE    
  Counter  

wfApplePortZipInZipReplies 1.3.6.1.4.1.18.3.5.4.3.1.48
The number of ZIP Replies received by this entity.
Status: mandatory Access: read-only
OBJECT-TYPE    
  Counter  

wfApplePortZipOutZipReplies 1.3.6.1.4.1.18.3.5.4.3.1.49
The number of ZIP Replies sent by this entity.
Status: mandatory Access: read-only
OBJECT-TYPE    
  Counter  

wfApplePortZipInZipExtendedReplies 1.3.6.1.4.1.18.3.5.4.3.1.50
The number of ZIP Extended Replies received by this entity.
Status: mandatory Access: read-only
OBJECT-TYPE    
  Counter  

wfApplePortZipOutZipExtendedReplies 1.3.6.1.4.1.18.3.5.4.3.1.51
The number of ZIP Extended Replies sent by this entity.
Status: mandatory Access: read-only
OBJECT-TYPE    
  Counter  

wfApplePortZipInGetZoneLists 1.3.6.1.4.1.18.3.5.4.3.1.52
The number of ZIP GetZoneList transactions received by this entity.
Status: mandatory Access: read-only
OBJECT-TYPE    
  Counter  

wfApplePortZipOutGetZoneListReplies 1.3.6.1.4.1.18.3.5.4.3.1.53
The number of ZIP GetZoneListReply transactions sent by this entity.
Status: mandatory Access: read-only
OBJECT-TYPE    
  Counter  

wfApplePortZipInGetLocalZones 1.3.6.1.4.1.18.3.5.4.3.1.54
The number of ZIP GetLocalZone transactions received by this entity.
Status: mandatory Access: read-only
OBJECT-TYPE    
  Counter  

wfApplePortZipOutGetLocalZoneReplies 1.3.6.1.4.1.18.3.5.4.3.1.55
The number of ZIP GetLocalZoneReply transactions sent by this entity.
Status: mandatory Access: read-only
OBJECT-TYPE    
  Counter  

wfApplePortZipInGetMyZones 1.3.6.1.4.1.18.3.5.4.3.1.56
The number of ZIP GetMyZone transactions received by this entity.
Status: mandatory Access: read-only
OBJECT-TYPE    
  Counter  

wfApplePortZipOutGetMyZoneReplies 1.3.6.1.4.1.18.3.5.4.3.1.57
The number of ZIP GetMyZoneReply transactions sent by this entity.
Status: mandatory Access: read-only
OBJECT-TYPE    
  Counter  

wfApplePortZipZoneConflictErrors 1.3.6.1.4.1.18.3.5.4.3.1.58
The number of times a conflict has been detected between this entity's zone information and another entity's zone information.
Status: mandatory Access: read-only
OBJECT-TYPE    
  Counter  

wfApplePortZipInGetNetInfos 1.3.6.1.4.1.18.3.5.4.3.1.59
The number of ZIP GetNetInfo packets received on this port by this entity.
Status: mandatory Access: read-only
OBJECT-TYPE    
  Counter  

wfApplePortZipOutGetNetInfoReplies 1.3.6.1.4.1.18.3.5.4.3.1.60
The number of ZIP GetNetInfoReply packets sent out this port by this entity.
Status: mandatory Access: read-only
OBJECT-TYPE    
  Counter  

wfApplePortZipZoneOutInvalids 1.3.6.1.4.1.18.3.5.4.3.1.61
The number of times this entity has sent a ZIP GetNetInfo Reply with the zone invalid bit set in response to a GetNetInfo Request with an invalid zone name.
Status: mandatory Access: read-only
OBJECT-TYPE    
  Counter  

wfApplePortZipAddressInvalids 1.3.6.1.4.1.18.3.5.4.3.1.62
The number of times this entity had to broadcast a ZIP GetNetInfo Reply because the GetNetInfo Request had an invalid address.
Status: mandatory Access: read-only
OBJECT-TYPE    
  Counter  

wfApplePortZipOutGetNetInfos 1.3.6.1.4.1.18.3.5.4.3.1.63
The number of ZIP GetNetInfo packets sent out this port by this entity.
Status: mandatory Access: read-only
OBJECT-TYPE    
  Counter  

wfApplePortZipInGetNetInfoReplies 1.3.6.1.4.1.18.3.5.4.3.1.64
The number of ZIP GetNetInfoReply packets received on this port by this entity.
Status: mandatory Access: read-only
OBJECT-TYPE    
  Counter  

wfApplePortZipOutZipQueries 1.3.6.1.4.1.18.3.5.4.3.1.65
The number of ZIP Queries sent by this entity.
Status: mandatory Access: read-only
OBJECT-TYPE    
  Counter  

wfApplePortZipInErrors 1.3.6.1.4.1.18.3.5.4.3.1.66
The number of ZIP packets received by this entity that were rejected for any error.
Status: mandatory Access: read-only
OBJECT-TYPE    
  Counter  

wfApplePortNbpInLookUpRequests 1.3.6.1.4.1.18.3.5.4.3.1.67
The number of NBP LookUp Requests received.
Status: mandatory Access: read-only
OBJECT-TYPE    
  Counter  

wfApplePortNbpInLookUpReplies 1.3.6.1.4.1.18.3.5.4.3.1.68
The number of NBP LookUp Replies received.
Status: mandatory Access: read-only
OBJECT-TYPE    
  Counter  

wfApplePortNbpInBroadcastRequests 1.3.6.1.4.1.18.3.5.4.3.1.69
The number of NBP Broadcast Requests received.
Status: mandatory Access: read-only
OBJECT-TYPE    
  Counter  

wfApplePortNbpInForwardRequests 1.3.6.1.4.1.18.3.5.4.3.1.70
The number of NBP Forward Requests received.
Status: mandatory Access: read-only
OBJECT-TYPE    
  Counter  

wfApplePortNbpOutLookUpRequests 1.3.6.1.4.1.18.3.5.4.3.1.71
The number of NBP LookUp Requests sent.
Status: mandatory Access: read-only
OBJECT-TYPE    
  Counter  

wfApplePortNbpOutLookUpReplies 1.3.6.1.4.1.18.3.5.4.3.1.72
The number of NBP LookUp Replies sent.
Status: mandatory Access: read-only
OBJECT-TYPE    
  Counter  

wfApplePortNbpOutBroadcastRequests 1.3.6.1.4.1.18.3.5.4.3.1.73
The number of NBP Broadcast Requests sent.
Status: mandatory Access: read-only
OBJECT-TYPE    
  Counter  

wfApplePortNbpOutForwardRequests 1.3.6.1.4.1.18.3.5.4.3.1.74
The number of NBP Forward Requests sent.
Status: mandatory Access: read-only
OBJECT-TYPE    
  Counter  

wfApplePortNbpRegistrationFailures 1.3.6.1.4.1.18.3.5.4.3.1.75
The number of times this node experienced a failure in attempting to register an NBP entity.
Status: mandatory Access: read-only
OBJECT-TYPE    
  Counter  

wfApplePortNbpInErrors 1.3.6.1.4.1.18.3.5.4.3.1.76
The number of NBP packets received by this entity that were rejected for any error.
Status: mandatory Access: read-only
OBJECT-TYPE    
  Counter  

wfApplePortEchoRequests 1.3.6.1.4.1.18.3.5.4.3.1.77
The number of AppleTalk Echo requests received.
Status: mandatory Access: read-only
OBJECT-TYPE    
  Counter  

wfApplePortEchoReplies 1.3.6.1.4.1.18.3.5.4.3.1.78
The number of AppleTalk Echo replies sent.
Status: mandatory Access: read-only
OBJECT-TYPE    
  Counter  

wfAppleLclZoneTable 1.3.6.1.4.1.18.3.5.4.4
The Local Zone table describes a list of zone names s serviced by a particular AppleTalk port/interface. In other words, the list of zone names that are associated with a particular network range.
Status: mandatory Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    WfAppleLclZoneEntry

wfAppleLclZoneEntry 1.3.6.1.4.1.18.3.5.4.4.1
An entry in the Local Zone table
Status: mandatory Access: not-accessible
OBJECT-TYPE    
  WfAppleLclZoneEntry  

wfAppleLclZoneDelete 1.3.6.1.4.1.18.3.5.4.4.1.1
Create/Delete parameter for adding/deleting a zone name to the Local Zone List for a particular AppleTalk network interface.
Status: mandatory Access: read-write
OBJECT-TYPE    
  INTEGER created(1), deleted(2)  

wfAppleLclZonePortCircuit 1.3.6.1.4.1.18.3.5.4.4.1.2
The circuit number for the corresponding AppleTalk interface /port for this zone list.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER  

wfAppleLclZoneIndex 1.3.6.1.4.1.18.3.5.4.4.1.3
A unique value for this zone name.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER  

wfAppleLclZoneName 1.3.6.1.4.1.18.3.5.4.4.1.4
One of the local zone names defined for this/ interface.
Status: mandatory Access: read-write
OBJECT-TYPE    
  DisplayString  

wfAppleAarpTable 1.3.6.1.4.1.18.3.5.4.5
The AppleTalk Address Translation table contains a mapping of AppleTalk Network addresses to its corresponding physical address.
Status: mandatory Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    WfAppleAarpEntry

wfAppleAarpEntry 1.3.6.1.4.1.18.3.5.4.5.1
An entry in the Address Mapping table
Status: mandatory Access: not-accessible
OBJECT-TYPE    
  WfAppleAarpEntry  

wfAppleAarpIfIndex 1.3.6.1.4.1.18.3.5.4.5.1.1
The unique value for this interface/cct. This value is the same interface as identified by the value of ifIndex.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER  

wfAppleAarpNet 1.3.6.1.4.1.18.3.5.4.5.1.2
The host's AppleTalk address (Net.Nodeid). This address corresponds to the media-dependent 'physical' address for this host.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER  

wfAppleAarpNode 1.3.6.1.4.1.18.3.5.4.5.1.3
The host's AppleTalk address (Net.Nodeid). This address corresponds to the media-dependent 'physical' address for this host.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER  

wfAppleAarpPhysAddress 1.3.6.1.4.1.18.3.5.4.5.1.4
The media-dependent 'physical' address.
Status: mandatory Access: read-only
OBJECT-TYPE    
  OCTET STRING  

wfAppleZipTable 1.3.6.1.4.1.18.3.5.4.6
The Zone Information table for reachable AppleTalk Networks.
Status: mandatory Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    WfAppleZipEntry

wfAppleZipEntry 1.3.6.1.4.1.18.3.5.4.6.1
An entry in the Zone Information table
Status: mandatory Access: not-accessible
OBJECT-TYPE    
  WfAppleZipEntry  

wfAppleZipZoneNetStart 1.3.6.1.4.1.18.3.5.4.6.1.1
The network that starts the range for this entry.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER  

wfAppleZipZoneNetEnd 1.3.6.1.4.1.18.3.5.4.6.1.2
The network that ends the range for this entry.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER  

wfAppleZipIndex 1.3.6.1.4.1.18.3.5.4.6.1.3
The unique value for this zone name.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER  

wfAppleZipZoneName 1.3.6.1.4.1.18.3.5.4.6.1.4
The ASCII xone name of this entry.
Status: mandatory Access: read-only
OBJECT-TYPE    
  DisplayString  

wfAppleZipZoneState 1.3.6.1.4.1.18.3.5.4.6.1.5
The state of the ZIP entry. Setting this object to the value invalid(2) has the effect of invalidating the corresponding entry in the ZipTable. It effectively, disassociates the mapping identified with this entry.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER valid(1), invalid(2)  

wfBrTp 1.3.6.1.4.1.18.3.5.1.1.1.1
OBJECT IDENTIFIER    

wfBrTpBaseDelete 1.3.6.1.4.1.18.3.5.1.1.1.1.1
Create/Delete parameter. Default is created. Users perform an SNMP SET operation on this object in order to create/delete the bridge.
Status: mandatory Access: read-write
OBJECT-TYPE    
  INTEGER created(1), deleted(2)  

wfBrTpBaseEnable 1.3.6.1.4.1.18.3.5.1.1.1.1.2
Enable/Disable parameter. Default is enabled. Users perform an SNMP SET operation on this object in order to enable/disable the bridge.
Status: mandatory Access: read-write
OBJECT-TYPE    
  INTEGER enabled(1), disabled(2)  

wfBrTpBaseState 1.3.6.1.4.1.18.3.5.1.1.1.1.3
The current state of the entire Bridge.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER up(1), down(2), init(3), pres(4)  

wfBrTpFdbTable 1.3.6.1.4.1.18.3.5.1.1.1.2
A table that contains information about unicast entries for which the bridge has forwarding and/or filtering information. This information is used by the transparent bridging function in determining how to propagate a received frame. inst = wfBrTpBaseFdbAddress
Status: mandatory Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    WfBrTpFdbEntry

wfBrTpFdbEntry 1.3.6.1.4.1.18.3.5.1.1.1.2.1
An entry in the wfBrTpFdbTable.
Status: mandatory Access: not-accessible
OBJECT-TYPE    
  WfBrTpFdbEntry  

wfBrTpBaseFdbAddress 1.3.6.1.4.1.18.3.5.1.1.1.2.1.1
A unicast MAC address for which the bridge has forwarding and/or filtering information.
Status: mandatory Access: read-only
OBJECT-TYPE    
  OCTET STRING  

wfBrTpBaseFdbPort 1.3.6.1.4.1.18.3.5.1.1.1.2.1.2
The port number on which the wfBrTpBaseFdbAddress was learned.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER  

wfBrTpBaseFdbStatus 1.3.6.1.4.1.18.3.5.1.1.1.2.1.3
The status of this entry. The meanings of the values are: learned(3) : the value of the corresponding instance of wfBrTpFdbPort was learned, and is being used.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER learned(3)  

wfBrTpInterface 1.3.6.1.4.1.18.3.5.1.1.3
A table that contains information about every interface that is associated with this transparent bridge. inst_id[1] = wfBrTpInterfaceCircuit
Status: mandatory Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    WfBrTpInterfaceEntry

wfBrTpInterfaceEntry 1.3.6.1.4.1.18.3.5.1.1.3.1
An entry in wfBrTpInterface.
Status: mandatory Access: not-accessible
OBJECT-TYPE    
  WfBrTpInterfaceEntry  

wfBrTpInterfaceDelete 1.3.6.1.4.1.18.3.5.1.1.3.1.1
Create/Delete parameter. Default is created. Users perform an SNMP SET operation on this object in order to create/delete an interface.
Status: mandatory Access: read-write
OBJECT-TYPE    
  INTEGER created(1), deleted(2)  

wfBrTpInterfaceEnable 1.3.6.1.4.1.18.3.5.1.1.3.1.2
Enable/Disable parameter. Default is enabled. Users perform an SNMP SET operation on this object in order to enable/disable an interface.
Status: mandatory Access: read-write
OBJECT-TYPE    
  INTEGER enabled(1), disabled(2)  

wfBrTpInterfaceState 1.3.6.1.4.1.18.3.5.1.1.3.1.3
The current state of the interface.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER up(1), down(2), init(3), pres(4)  

wfBrTpInterfaceCircuit 1.3.6.1.4.1.18.3.5.1.1.3.1.4
The circuit that this interface runs over.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER  

wfBrTpInterfaceMaxInfo 1.3.6.1.4.1.18.3.5.1.1.3.1.5
The maximum size of the INFO (non-MAC) field that this port will receive or transmit.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER  

wfBrTpInterfaceInFrames 1.3.6.1.4.1.18.3.5.1.1.3.1.6
The number of frames that have been received by this interface from its circuit.
Status: mandatory Access: read-only
OBJECT-TYPE    
  Counter  

wfBrTpInterfaceOutFrames 1.3.6.1.4.1.18.3.5.1.1.3.1.7
The number of frames that have been transmitted by this interface to its circuit.
Status: mandatory Access: read-only
OBJECT-TYPE    
  Counter  

wfBrTpInterfaceInDiscards 1.3.6.1.4.1.18.3.5.1.1.3.1.8
Count of valid frames received which were received on this interface but then discarded.
Status: mandatory Access: read-only
OBJECT-TYPE    
  Counter  

wfBrTrafficFilterTable 1.3.6.1.4.1.18.3.5.1.1.4
Bridge Traffic Filters
Status: mandatory Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    WfBrTrafficFilterEntry

wfBrTrafficFilterEntry 1.3.6.1.4.1.18.3.5.1.1.4.1
An entry in WfBrTrafficFilterTable.
Status: mandatory Access: not-accessible
OBJECT-TYPE    
  WfBrTrafficFilterEntry  

wfBrTrafficFilterCreate 1.3.6.1.4.1.18.3.5.1.1.4.1.1
Defines the existence of the traffic filter rule: created - traffic filter exists delete - traffic filter does not exist and can be deleted.
Status: mandatory Access: read-write
OBJECT-TYPE    
  INTEGER created(1), deleted(2)  

wfBrTrafficFilterEnable 1.3.6.1.4.1.18.3.5.1.1.4.1.2
Defines whether or not the traffic filter rule should be used: enabled - activate the rule. disabled - inactivate the rule.
Status: mandatory Access: read-write
OBJECT-TYPE    
  INTEGER enabled(1), disabled(2)  

wfBrTrafficFilterStatus 1.3.6.1.4.1.18.3.5.1.1.4.1.3
Defines the current status of the traffic filter: inactive - the rule is not in use. active - the rule is being used. error - the application detected an error in the rule.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER active(1), error(2), inactive(3)  

wfBrTrafficFilterCounter 1.3.6.1.4.1.18.3.5.1.1.4.1.4
The number of received packets that have matched this rule.
Status: mandatory Access: read-only
OBJECT-TYPE    
  Counter  

wfBrTrafficFilterDefinition 1.3.6.1.4.1.18.3.5.1.1.4.1.5
The filter rule definition.
Status: mandatory Access: read-write
OBJECT-TYPE    
  Opaque  

wfBrTrafficFilterReserved 1.3.6.1.4.1.18.3.5.1.1.4.1.6
Reserved field.
Status: mandatory Access: not-accessible
OBJECT-TYPE    
  INTEGER  

wfBrTrafficFilterCircuit 1.3.6.1.4.1.18.3.5.1.1.4.1.7
The ID of the Bridge Circuit to which the filter is applied.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER  

wfBrTrafficFilterRuleNumber 1.3.6.1.4.1.18.3.5.1.1.4.1.8
ID for the rule.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER  

wfBrTrafficFilterFragment 1.3.6.1.4.1.18.3.5.1.1.4.1.9
Fragment number - for large rules.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER  

wfCctOptsTable 1.3.6.1.4.1.18.3.5.1.4.1
The table of circuit names
Status: mandatory Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    WfCctOptsEntry

wfCctOptsEntry 1.3.6.1.4.1.18.3.5.1.4.1.1
Entry format for the table of circuit options
Status: mandatory Access: not-accessible
OBJECT-TYPE    
  WfCctOptsEntry  

wfCctOptsDelete 1.3.6.1.4.1.18.3.5.1.4.1.1.1
Creation and deletion flag for this record
Status: mandatory Access: read-write
OBJECT-TYPE    
  INTEGER created(1), deleted(2)  

wfCctOptsPriorityQueueingDisable 1.3.6.1.4.1.18.3.5.1.4.1.1.2
Priority Queuing option
Status: mandatory Access: read-write
OBJECT-TYPE    
  INTEGER enabled(1), disabled(2)  

wfCctOptsCct 1.3.6.1.4.1.18.3.5.1.4.1.1.3
circuit number
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER  

wfCctOptsHighPriorityQueueLimit 1.3.6.1.4.1.18.3.5.1.4.1.1.4
High Priority Queue limit The minimum valid value is zero. The maximum valid value is 63 (HW xmit ring size) minus the sum of the Normal and Low queue limits.
Status: mandatory Access: read-write
OBJECT-TYPE    
  INTEGER default(20)  

wfCctOptsNormalPriorityQueueLimit 1.3.6.1.4.1.18.3.5.1.4.1.1.5
Normal Priority Queue limit The minimum valid value is zero. The maximum valid value is 63 (HW xmit ring size) minus the sum of the High and Low queue limits.
Status: mandatory Access: read-write
OBJECT-TYPE    
  INTEGER default(20)  

wfCctOptsLowPriorityQueueLimit 1.3.6.1.4.1.18.3.5.1.4.1.1.6
Low Priority Queue limit The minimum valid value is zero. The maximum valid value is 63 (HW xmit ring size) minus the sum of the High and Normal queue limits.
Status: mandatory Access: read-write
OBJECT-TYPE    
  INTEGER default(20)  

wfCctOptsMaxInterruptQueueLatency 1.3.6.1.4.1.18.3.5.1.4.1.1.7
Interrupt Queue Latency
Status: mandatory Access: read-write
OBJECT-TYPE    
  INTEGER minimum(100), default(2500), maximum(5000)  

wfCctOptsMaxHighPriorityQueueLatency 1.3.6.1.4.1.18.3.5.1.4.1.1.8
High Priority Queue Latency
Status: mandatory Access: read-write
OBJECT-TYPE    
  INTEGER minimum(100), default(250), maximum(5000)  

wfCctOptsHiXmits 1.3.6.1.4.1.18.3.5.1.4.1.1.9
High Priority Transmit count
Status: mandatory Access: read-only
OBJECT-TYPE    
  Counter  

wfCctOptsNormalXmits 1.3.6.1.4.1.18.3.5.1.4.1.1.10
Normal Priority Transmit count
Status: mandatory Access: read-only
OBJECT-TYPE    
  Counter  

wfCctOptsLoXmits 1.3.6.1.4.1.18.3.5.1.4.1.1.11
Low Priority Transmit count
Status: mandatory Access: read-only
OBJECT-TYPE    
  Counter  

wfCctOptsHiClippedPkts 1.3.6.1.4.1.18.3.5.1.4.1.1.12
High Prio Transmit Clip Count
Status: mandatory Access: read-only
OBJECT-TYPE    
  Counter  

wfCctOptsNormalClippedPkts 1.3.6.1.4.1.18.3.5.1.4.1.1.13
Normal Prio Transmit Clip Count
Status: mandatory Access: read-only
OBJECT-TYPE    
  Counter  

wfCctOptsLoClippedPkts 1.3.6.1.4.1.18.3.5.1.4.1.1.14
Low Prio Transmit Clip Count
Status: mandatory Access: read-only
OBJECT-TYPE    
  Counter  

wfCctOptsIntrQHighWaterPkts 1.3.6.1.4.1.18.3.5.1.4.1.1.15
Interrupt Queue high-water mark
Status: mandatory Access: read-only
OBJECT-TYPE    
  Gauge  

wfCctOptsHiQHighWaterPkts 1.3.6.1.4.1.18.3.5.1.4.1.1.16
High-priority Queue high-water mark
Status: mandatory Access: read-only
OBJECT-TYPE    
  Gauge  

wfCctOptsNormalQHighWaterPkts 1.3.6.1.4.1.18.3.5.1.4.1.1.17
Normal Queue high-water mark
Status: mandatory Access: read-only
OBJECT-TYPE    
  Gauge  

wfCctOptsLoQHighWaterPkts 1.3.6.1.4.1.18.3.5.1.4.1.1.18
Low-priority Queue high-water mark
Status: mandatory Access: read-only
OBJECT-TYPE    
  Gauge  

wfCctOptsHighWaterPktsClear 1.3.6.1.4.1.18.3.5.1.4.1.1.19
Attribute to clear the high-water marks. When the MIB changes, Priority Queueing (if ENABLED) checks to see if HighWaterPktsClear is different than the last time the MIB was modified in any way. If it is different, all the high water marks (see above) are set to zero.
Status: mandatory Access: read-write
OBJECT-TYPE    
  INTEGER  

wfCctOptsDroppedPkts 1.3.6.1.4.1.18.3.5.1.4.1.1.20
Packets which were filtered in Priority Queueing
Status: mandatory Access: read-only
OBJECT-TYPE    
  Counter  

wfCctOptsLargePkts 1.3.6.1.4.1.18.3.5.1.4.1.1.21
Large Packets which became an exception to latency rules
Status: mandatory Access: read-only
OBJECT-TYPE    
  Counter  

wfCctOptsRxPkts 1.3.6.1.4.1.18.3.5.1.4.1.1.22
Packets received
Status: mandatory Access: read-only
OBJECT-TYPE    
  Counter  

wfCctOptsBrFilterTable 1.3.6.1.4.1.18.3.5.1.4.2
Bridge Filters
Status: mandatory Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    WfCctOptsBrFilterEntry

wfCctOptsBrFilterEntry 1.3.6.1.4.1.18.3.5.1.4.2.1
An entry in WfCctOptsBrFilterTable.
Status: mandatory Access: not-accessible
OBJECT-TYPE    
  WfCctOptsBrFilterEntry  

wfCctOptsBrFilterCreate 1.3.6.1.4.1.18.3.5.1.4.2.1.1
Defines the existence of the traffic filter rule: created - traffic filter exists delete - traffic filter does not exist and can be deleted.
Status: mandatory Access: read-write
OBJECT-TYPE    
  INTEGER created(1), deleted(2)  

wfCctOptsBrFilterEnable 1.3.6.1.4.1.18.3.5.1.4.2.1.2
Defines whether or not the traffic filter rule should be used: enabled - activate the rule. disabled - inactivate the rule.
Status: mandatory Access: read-write
OBJECT-TYPE    
  INTEGER enabled(1), disabled(2)  

wfCctOptsBrFilterState 1.3.6.1.4.1.18.3.5.1.4.2.1.3
Defines the current State of the traffic filter: inactive - the rule is not in use. active - the rule is being used. error - the application detected an error in the rule.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER active(1), error(2), inactive(3)  

wfCctOptsBrFilterCounter 1.3.6.1.4.1.18.3.5.1.4.2.1.4
The number of received packets that have matched this rule.
Status: mandatory Access: read-only
OBJECT-TYPE    
  Counter  

wfCctOptsBrFilterDefinition 1.3.6.1.4.1.18.3.5.1.4.2.1.5
The filter rule definition.
Status: mandatory Access: read-write
OBJECT-TYPE    
  OCTET STRING  

wfCctOptsBrFilterReserved 1.3.6.1.4.1.18.3.5.1.4.2.1.6
Reserved field.
Status: mandatory Access: not-accessible
OBJECT-TYPE    
  INTEGER  

wfCctOptsBrFilterCct 1.3.6.1.4.1.18.3.5.1.4.2.1.7
The ID of the CctBridge Cct to which the filter is applied.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER  

wfCctOptsBrFilterRuleNumber 1.3.6.1.4.1.18.3.5.1.4.2.1.8
ID for the rule.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER  

wfCctOptsBrFilterFragment 1.3.6.1.4.1.18.3.5.1.4.2.1.9
Fragment number - for large rules.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER  

wfCctOptsIpFilterTable 1.3.6.1.4.1.18.3.5.1.4.3
Ip Filters
Status: mandatory Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    WfCctOptsIpFilterEntry

wfCctOptsIpFilterEntry 1.3.6.1.4.1.18.3.5.1.4.3.1
An entry in WfCctOptsIpFilterTable.
Status: mandatory Access: not-accessible
OBJECT-TYPE    
  WfCctOptsIpFilterEntry  

wfCctOptsIpFilterCreate 1.3.6.1.4.1.18.3.5.1.4.3.1.1
Defines the existence of the traffic filter rule: created - traffic filter exists delete - traffic filter does not exist and can be deleted.
Status: mandatory Access: read-write
OBJECT-TYPE    
  INTEGER created(1), deleted(2)  

wfCctOptsIpFilterEnable 1.3.6.1.4.1.18.3.5.1.4.3.1.2
Defines whether or not the traffic filter rule should be used: enabled - activate the rule. disabled - inactivate the rule.
Status: mandatory Access: read-write
OBJECT-TYPE    
  INTEGER enabled(1), disabled(2)  

wfCctOptsIpFilterState 1.3.6.1.4.1.18.3.5.1.4.3.1.3
Defines the current State of the traffic filter: inactive - the rule is not in use. active - the rule is being used. error - the application detected an error in the rule.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER active(1), error(2), inactive(3)  

wfCctOptsIpFilterCounter 1.3.6.1.4.1.18.3.5.1.4.3.1.4
The number of received packets that have matched this rule.
Status: mandatory Access: read-only
OBJECT-TYPE    
  Counter  

wfCctOptsIpFilterDefinition 1.3.6.1.4.1.18.3.5.1.4.3.1.5
The filter rule definition.
Status: mandatory Access: read-write
OBJECT-TYPE    
  OCTET STRING  

wfCctOptsIpFilterReserved 1.3.6.1.4.1.18.3.5.1.4.3.1.6
Reserved field.
Status: mandatory Access: not-accessible
OBJECT-TYPE    
  INTEGER  

wfCctOptsIpFilterCct 1.3.6.1.4.1.18.3.5.1.4.3.1.7
The ID of the CctIp Cct to which the filter is applied.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER  

wfCctOptsIpFilterRuleNumber 1.3.6.1.4.1.18.3.5.1.4.3.1.8
ID for the rule.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER  

wfCctOptsIpFilterFragment 1.3.6.1.4.1.18.3.5.1.4.3.1.9
Fragment number - for large rules.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER  

wfCctOptsLengthBasedTable 1.3.6.1.4.1.18.3.5.1.4.4
Length Based Priority Table
Status: mandatory Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    WfCctOptsLengthBasedEntry

wfCctOptsLengthBasedEntry 1.3.6.1.4.1.18.3.5.1.4.4.1
An entry in WfCctOptsLengthBasedTable.
Status: mandatory Access: not-accessible
OBJECT-TYPE    
  WfCctOptsLengthBasedEntry  

wfCctOptsLengthBasedDelete 1.3.6.1.4.1.18.3.5.1.4.4.1.1
Defines the existence of the length based priority filter rule: created - traffic filter exists delete - traffic filter does not exist and can be deleted.
Status: mandatory Access: read-write
OBJECT-TYPE    
  INTEGER created(1), deleted(2)  

wfCctOptsLengthBasedDisable 1.3.6.1.4.1.18.3.5.1.4.4.1.2
Defines whether or not the length based priority filter rule should be used: enabled - activate the rule. disabled - inactivate the rule.
Status: mandatory Access: read-write
OBJECT-TYPE    
  INTEGER enabled(1), disabled(2)  

wfCctOptsLengthBasedState 1.3.6.1.4.1.18.3.5.1.4.4.1.3
Defines the current State of the length based priority filter: inactive - the rule is not in use. active - the rule is being used. error - the application detected an error in the rule.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER active(1), error(2), inactive(3)  

wfCctOptsLengthBasedCct 1.3.6.1.4.1.18.3.5.1.4.4.1.4
The ID of the Cct to which the filter is applied
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER  

wfCctOptsLengthBasedMux 1.3.6.1.4.1.18.3.5.1.4.4.1.5
packet mux type
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER etype(1), lsap(2), snap(3)  

wfCctOptsLengthBasedData 1.3.6.1.4.1.18.3.5.1.4.4.1.6
a five byte quantity of the form ethernet - 0x6003000000 (e.g. DECnet) lsap - 0xfefe030000 (e.g. OSI) snap - 0x0000000800 (e.g. IP) - 0x0800070800 (e.g. Appletalk DDP)
Status: mandatory Access: read-only
OBJECT-TYPE    
  OCTET STRING  

wfCctOptsLengthBasedLength 1.3.6.1.4.1.18.3.5.1.4.4.1.7
Maximum length of a packet to be considered high priority
Status: mandatory Access: read-write
OBJECT-TYPE    
  INTEGER  

wfCctOptsLengthBasedLessThanQ 1.3.6.1.4.1.18.3.5.1.4.4.1.8
queue into which packets of length less than or equal wfCctOptsLengthBasedLength are placed
Status: mandatory Access: read-write
OBJECT-TYPE    
  INTEGER hi(3), normal(2), lo(1)  

wfCctOptsLengthBasedGreaterThanQ 1.3.6.1.4.1.18.3.5.1.4.4.1.9
queue into which packets of length greater than wfCctOptsLengthBasedLength are placed
Status: mandatory Access: read-write
OBJECT-TYPE    
  INTEGER hi(3), normal(2), lo(1)  

wfCircuitNameTable 1.3.6.1.4.1.18.3.3.2.3
The table of circuit names
Status: mandatory Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    WfCircuitNameEntry

wfCircuitNameEntry 1.3.6.1.4.1.18.3.3.2.3.1
Entry format for the table of circuit names
Status: mandatory Access: not-accessible
OBJECT-TYPE    
  WfCircuitNameEntry  

wfCircuitNameDelete 1.3.6.1.4.1.18.3.3.2.3.1.1
Creation and deletion flag for this record
Status: mandatory Access: read-write
OBJECT-TYPE    
  INTEGER create(1), delete(2)  

wfCircuitNumber 1.3.6.1.4.1.18.3.3.2.3.1.2
circuit number
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER  

wfCircuitName 1.3.6.1.4.1.18.3.3.2.3.1.3
circuit name
Status: mandatory Access: read-write
OBJECT-TYPE    
  DisplayString  

wfCircuitIfType 1.3.6.1.4.1.18.3.3.2.3.1.4
circuit interface type
Status: mandatory Access: read-write
OBJECT-TYPE    
  INTEGER csmacd(10), sync(20), t1(30), e1(40), token(50), fddi(60), hssi(70)  

wfCircuitProtoMap 1.3.6.1.4.1.18.3.3.2.3.1.5
The Circuit-Protocol mask
Status: mandatory Access: read-write
OBJECT-TYPE    
  OCTET STRING  

wfConsole 1.3.6.1.4.1.18.3.3.2.1
OBJECT IDENTIFIER    

wfBaudRate 1.3.6.1.4.1.18.3.3.2.1.1
Baud rate configured on the Technician Interface console
Status: mandatory Access: read-write
OBJECT-TYPE    
  INTEGER  

wfDataBits 1.3.6.1.4.1.18.3.3.2.1.2
Number of data bits configured on the Technician Interface console
Status: mandatory Access: read-write
OBJECT-TYPE    
  INTEGER  

wfParity 1.3.6.1.4.1.18.3.3.2.1.3
Type of parity configured on the Technician Interface console
Status: mandatory Access: read-write
OBJECT-TYPE    
  INTEGER none(1), odd(2), even(3)  

wfStopBits 1.3.6.1.4.1.18.3.3.2.1.4
Number of stop bits configured on the Technician Interface console
Status: mandatory Access: read-write
OBJECT-TYPE    
  INTEGER s1bit(1), s15bit(2), s2bit(3)  

wfModemEnable 1.3.6.1.4.1.18.3.3.2.1.5
Enable the Technician Interface console to run over a modem
Status: mandatory Access: read-write
OBJECT-TYPE    
  INTEGER enabled(1), disabled(2)  

wfLinesPerScreen 1.3.6.1.4.1.18.3.3.2.1.6
Number of lines which can be displayed in one screen on the Technician Interface console
Status: mandatory Access: read-write
OBJECT-TYPE    
  INTEGER  

wfMoreEnable 1.3.6.1.4.1.18.3.3.2.1.7
Enable the 'more' feature on the Technician Interface console
Status: mandatory Access: read-write
OBJECT-TYPE    
  INTEGER enabled(1), disabled(2)  

wfPrompt 1.3.6.1.4.1.18.3.3.2.1.8
Character string which will be used as the system prompt on the Technician Interface console
Status: mandatory Access: read-write
OBJECT-TYPE    
  DisplayString  

wfLoginTimeOut 1.3.6.1.4.1.18.3.3.2.1.9
IF MODEM_ENABLED then time out in minutes to HUP when at the login prompt
Status: mandatory Access: read-write
OBJECT-TYPE    
  INTEGER minimum(1), maximum(99), default(1)  

wfPasswordTimeOut 1.3.6.1.4.1.18.3.3.2.1.10
Timout on Password entry
Status: mandatory Access: read-write
OBJECT-TYPE    
  INTEGER minimum(1), maximum(99), default(1)  

wfCommandTimeOut 1.3.6.1.4.1.18.3.3.2.1.11
IF MODEM_ENABLED then time out in minutes to HUP when at the command prompt
Status: mandatory Access: read-write
OBJECT-TYPE    
  INTEGER minimum(1), maximum(99), default(15)  

wfLoginRetries 1.3.6.1.4.1.18.3.3.2.1.12
IF MODEM_ENABLED then limit # of login attempts then HUP
Status: mandatory Access: read-write
OBJECT-TYPE    
  INTEGER minimum(1), maximum(99), default(3)  

wfTotalLogins 1.3.6.1.4.1.18.3.3.2.1.13
Total number of TI login attempts
Status: mandatory Access: read-only
OBJECT-TYPE    
  Counter  

wfUserLoginErrors 1.3.6.1.4.1.18.3.3.2.1.14
Total number of FAILED User login attempts
Status: mandatory Access: read-only
OBJECT-TYPE    
  Counter  

wfManagerLoginErrors 1.3.6.1.4.1.18.3.3.2.1.15
Total number of FAILED Manager login attempts
Status: mandatory Access: read-only
OBJECT-TYPE    
  Counter  

wfOtherLoginErrors 1.3.6.1.4.1.18.3.3.2.1.16
Total number of FAILED Other login attempts
Status: mandatory Access: read-only
OBJECT-TYPE    
  Counter  

wfTtyFrameErrors 1.3.6.1.4.1.18.3.3.2.1.17
Count of TTY Frame errors
Status: mandatory Access: read-only
OBJECT-TYPE    
  Counter  

wfTtyOverrunErrors 1.3.6.1.4.1.18.3.3.2.1.18
Count of TTY Overrun errors
Status: mandatory Access: read-only
OBJECT-TYPE    
  Counter  

wfTtyParityErrors 1.3.6.1.4.1.18.3.3.2.1.19
Count of TTY Parity errors
Status: mandatory Access: read-only
OBJECT-TYPE    
  Counter  

wfTtyInfifoErrors 1.3.6.1.4.1.18.3.3.2.1.20
Count of TTY Input Fifo errors
Status: mandatory Access: read-only
OBJECT-TYPE    
  Counter  

wfCSMACDTable 1.3.6.1.4.1.18.3.4.1
CSMA/CD line record
Status: mandatory Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    WfCSMACDEntry

wfCSMACDEntry 1.3.6.1.4.1.18.3.4.1.1
An entry in the csmacd table
Status: mandatory Access: not-accessible
OBJECT-TYPE    
  WfCSMACDEntry  

wfCSMACDDelete 1.3.6.1.4.1.18.3.4.1.1.1
create/delete parameter, dflt = created
Status: mandatory Access: read-write
OBJECT-TYPE    
  INTEGER create(1), delete(2)  

wfCSMACDEnable 1.3.6.1.4.1.18.3.4.1.1.2
enable/disable parameter, dflt = enabled
Status: mandatory Access: read-write
OBJECT-TYPE    
  INTEGER enable(1), disable(2)  

wfCSMACDState 1.3.6.1.4.1.18.3.4.1.1.3
line driver state variable, Not Present, Init, Down, Up
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER up(1), down(2), init(3), notpresent(4)  

wfCSMACDSlot 1.3.6.1.4.1.18.3.4.1.1.4
instance ID Slot, filled in by driver
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER minimum(1), maximum(14)  

wfCSMACDConnector 1.3.6.1.4.1.18.3.4.1.1.5
instance ID Connector, filled in by driver
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER one(1), two(2), three(3), four(4)  

wfCSMACDCct 1.3.6.1.4.1.18.3.4.1.1.6
cct number for this line instance
Status: mandatory Access: read-write
OBJECT-TYPE    
  INTEGER minimum(1), maximum(1023)  

wfCSMACDBofl 1.3.6.1.4.1.18.3.4.1.1.7
bofl parameter, dflt = enabled
Status: mandatory Access: read-write
OBJECT-TYPE    
  INTEGER enable(1), disable(2)  

wfCSMACDBoflTmo 1.3.6.1.4.1.18.3.4.1.1.8
bofl parameter, dflt = 5
Status: mandatory Access: read-write
OBJECT-TYPE    
  INTEGER minimum(1), maximum(60), default(5)  

wfCSMACDMtu 1.3.6.1.4.1.18.3.4.1.1.9
mtu parameter, fixed
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER default(1518)  

wfCSMACDMadr 1.3.6.1.4.1.18.3.4.1.1.10
line MAC address, fixed - line driver fills in
Status: mandatory Access: read-only
OBJECT-TYPE    
  OCTET STRING  

wfCSMACDOctetsRxOk 1.3.6.1.4.1.18.3.4.1.1.11
Number of octets received without error
Status: mandatory Access: read-only
OBJECT-TYPE    
  Counter  

wfCSMACDFramesRxOk 1.3.6.1.4.1.18.3.4.1.1.12
Number of frames received without error
Status: mandatory Access: read-only
OBJECT-TYPE    
  Counter  

wfCSMACDOctetsTxOk 1.3.6.1.4.1.18.3.4.1.1.13
Number of octets transmitted without error
Status: mandatory Access: read-only
OBJECT-TYPE    
  Counter  

wfCSMACDFramesTxOk 1.3.6.1.4.1.18.3.4.1.1.14
Number of frames transmitted without error
Status: mandatory Access: read-only
OBJECT-TYPE    
  Counter  

wfCSMACDDeferredTx 1.3.6.1.4.1.18.3.4.1.1.15
Number of deferred transmissions
Status: mandatory Access: read-only
OBJECT-TYPE    
  Counter  

wfCSMACDLateCollnTx 1.3.6.1.4.1.18.3.4.1.1.16
Number of late collisions
Status: mandatory Access: read-only
OBJECT-TYPE    
  Counter  

wfCSMACDExcessvCollnTx 1.3.6.1.4.1.18.3.4.1.1.17
Number of excessive collisions
Status: mandatory Access: read-only
OBJECT-TYPE    
  Counter  

wfCSMACDBablErrorTx 1.3.6.1.4.1.18.3.4.1.1.18
Number of frames transmitted larger than 1518 octets
Status: mandatory Access: read-only
OBJECT-TYPE    
  Counter  

wfCSMACDBufErrorTx 1.3.6.1.4.1.18.3.4.1.1.19
Number of internal buffer errors
Status: mandatory Access: read-only
OBJECT-TYPE    
  Counter  

wfCSMACDLcarTx 1.3.6.1.4.1.18.3.4.1.1.20
Number of loss of carrier errors
Status: mandatory Access: read-only
OBJECT-TYPE    
  Counter  

wfCSMACDUfloTx 1.3.6.1.4.1.18.3.4.1.1.21
Number of transmitter underflow errors
Status: mandatory Access: read-only
OBJECT-TYPE    
  Counter  

wfCSMACDFcsErrorRx 1.3.6.1.4.1.18.3.4.1.1.22
Number of receiver checksum errors
Status: mandatory Access: read-only
OBJECT-TYPE    
  Counter  

wfCSMACDAlignErrorRx 1.3.6.1.4.1.18.3.4.1.1.23
Number of receiver alignment errors
Status: mandatory Access: read-only
OBJECT-TYPE    
  Counter  

wfCSMACDLackRescErrorRx 1.3.6.1.4.1.18.3.4.1.1.24
Number of receiver lack of resource errors
Status: mandatory Access: read-only
OBJECT-TYPE    
  Counter  

wfCSMACDTooLongErrorRx 1.3.6.1.4.1.18.3.4.1.1.25
Number of frames received exceeding 1518 octets
Status: mandatory Access: read-only
OBJECT-TYPE    
  Counter  

wfCSMACDOfloRx 1.3.6.1.4.1.18.3.4.1.1.26
Number of receiver overflow errors
Status: mandatory Access: read-only
OBJECT-TYPE    
  Counter  

wfCSMACDMerr 1.3.6.1.4.1.18.3.4.1.1.27
Number of internal memory errors
Status: mandatory Access: read-only
OBJECT-TYPE    
  Counter  

wfCSMACDCerr 1.3.6.1.4.1.18.3.4.1.1.28
Number of collision errors
Status: mandatory Access: read-only
OBJECT-TYPE    
  Counter  

wfCSMACDHardwareFilter 1.3.6.1.4.1.18.3.4.1.1.29
Hardware filtering parameter.
Status: mandatory Access: read-write
OBJECT-TYPE    
  INTEGER enable(1), disable(2)  

wfCSMACDTxQueueLength 1.3.6.1.4.1.18.3.4.1.1.30
Transmit Queue Length, values larger than the compiled ring size are truncated to the compiled ring size.
Status: mandatory Access: read-write
OBJECT-TYPE    
  INTEGER minimum(1), maximum(255), default(32)  

wfCSMACDRxQueueLength 1.3.6.1.4.1.18.3.4.1.1.31
Receive Queue Length, values larger than the compiled ring size are truncated to the compiled ring size.
Status: mandatory Access: read-write
OBJECT-TYPE    
  INTEGER minimum(1), maximum(255), default(32)  

wfCSMACDTxClipFrames 1.3.6.1.4.1.18.3.4.1.1.32
Number of frames clipped in driver's transmit routine due to transmit congestion.
Status: mandatory Access: read-only
OBJECT-TYPE    
  Counter  

wfCSMACDRxReplenMisses 1.3.6.1.4.1.18.3.4.1.1.33
Number of packet buffer misses while attempting to replenish driver receive ring.
Status: mandatory Access: read-only
OBJECT-TYPE    
  Counter  

wfivRouteGroup 1.3.6.1.4.1.18.3.5.2.1
OBJECT IDENTIFIER    

wfivRouteCreateDelete 1.3.6.1.4.1.18.3.5.2.1.1
'This value determines whether DECnet is configured on this slot.'
Status: mandatory Access: read-write
OBJECT-TYPE    
  INTEGER create(1), delete(2)  

wfivRouteEnableDisable 1.3.6.1.4.1.18.3.5.2.1.2
'This value determines whether DECnet is to startup.'
Status: mandatory Access: read-write
OBJECT-TYPE    
  INTEGER enable(1), disable(2)  

wfivRouteState 1.3.6.1.4.1.18.3.5.2.1.3
'This value determines whether DECnet is to startup.'
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER notpresent(4), initializing(3), down(2), up(1)  

wfivRouteBroadcastRouteTimer 1.3.6.1.4.1.18.3.5.2.1.4
'This value determines the maximum time allowed between Routing updates on Ethernet circuits. When this timer expires before a routing update occurs, a routing update is forced. With a standard calculation, Routing also uses this timer to enforce a minimum delay between routing updates. Seconds is a decimal integer in the range 1-65535.'
Status: mandatory Access: read-write
OBJECT-TYPE    
  INTEGER routetimermin(1), routetimerdflt(180), routetimermax(65535)  

wfivRouteRoutingVers 1.3.6.1.4.1.18.3.5.2.1.5
'This read-only parameter identifies the executor node's Routing version number. The format is the same as for the Network Management version number.'
Status: mandatory Access: read-only
OBJECT-TYPE    
  DisplayString  

wfivRouteMaxAddr 1.3.6.1.4.1.18.3.5.2.1.6
'This value represents the largest node number and, therefore, number of nodes that can be known about by the executor node's home area. The number is an integer in the range 1-1023.'
Status: mandatory Access: read-write
OBJECT-TYPE    
  INTEGER minaddr(1), maxaddr(1023)  

wfivRouteMaxBdcastNonRouters 1.3.6.1.4.1.18.3.5.2.1.7
'This value represents the maximum total number of nonrouters the executor node can have on its broadcast circuits for one slot. The number is an integer in the range 0-1023.'
Status: mandatory Access: read-write
OBJECT-TYPE    
  INTEGER nonroutersdflt(64), nonroutersmax(1023)  

wfivRouteMaxBdcastRouters 1.3.6.1.4.1.18.3.5.2.1.8
'This value represents the maximum total number of routers the executor node can have on its broadcast circuits for one slot. The number is an integer in the range 0-1023.'
Status: mandatory Access: read-write
OBJECT-TYPE    
  INTEGER routersdflt(32), routersdmax(1023)  

wfivRouteMaxCircuits 1.3.6.1.4.1.18.3.5.2.1.9
'This value represents the maximum number of Routing circuits that the executor node can know about. The number is decimal in the range 1-65535. Wellfleet limits this to 1024'
Status: mandatory Access: read-write
OBJECT-TYPE    
  INTEGER circuitsmin(1), circuitsdflt(16), circuitswfmax(1024), circuitsmax(65535)  

wfivRouteMaxCost 1.3.6.1.4.1.18.3.5.2.1.10
'This value represents the maximum total path cost allowed from the executor to any node within an area. The path cost is the sum of the circuit costs along a path between two nodes. This parameter defines the point where the executor node's Routing decision algorithm declares another node unreachable because the cost of the least costly path to the other node is excessive. For correct operation, this parameter must not be less than the maximum path cost of the network. The MAXIMUM COST number is decimal in the range 1-1022.'
Status: mandatory Access: read-write
OBJECT-TYPE    
  INTEGER mincost(1), maxcost(1022)  

wfivRouteMaxHops 1.3.6.1.4.1.18.3.5.2.1.11
'This value represents the maximum number of routing hops allowable from the executor to any other reachable node within an area. (A hop is the logical distance over a circuit between two adjacent nodes.) This parameter defines the point where the executor node's Routing decision algorithm declares another node unreachable because the length of the shortest path between the two nodes is too long. For correct operation, this parameter must not be less than the network diameter. (The network diameter is the reachability distance between the two nodes of the network having the greatest reachability distance, where reachability distance is the length the shortest path between a given pair of nodes.) The MAXIMUM HOPS number is decimal in the range 1-30.'
Status: mandatory Access: read-write
OBJECT-TYPE    
  INTEGER minhops(1), maxhops(30)  

wfivRouteMaxVisits 1.3.6.1.4.1.18.3.5.2.1.12
'This value represents the maximum number of nodes a message coming into the executor node can have visited. If the message is not for this node and the MAXIMUM VISITS number is exceeded, the message is discarded. The MAXIMUM VISITS parameter defines the point where the packet lifetime control algorithm discards a packet that has traversed too many nodes. For correct operation, this parameter must not be less than the maximum path length of the network. (The maximum path length is the routing distance between the two nodes of the network having the greatest routing distance, where routing distance is the length of the least costly path between a given pair of nodes.) The MAXIMUM VISITS number is decimal in the range MAXIMUM HOPS to 63.'
Status: mandatory Access: read-write
OBJECT-TYPE    
  INTEGER maxvisits(63)  

wfivRouteAreaMaxCost 1.3.6.1.4.1.18.3.5.2.1.13
'This value represents the maximum total path cost allowed from the executor to any other level 2 routing node. The AREA MAXIMUM COST number is decimal in the range 1-1022. This parameter is only applicable if the executor node is of type AREA.'
Status: mandatory Access: read-write
OBJECT-TYPE    
  INTEGER amincost(1), amaxcost(1022)  

wfivRouteAreaMaxHops 1.3.6.1.4.1.18.3.5.2.1.14
'This value represents the maximum number of routing hops allowable from the executor to any other level 2 routing node. The AREA MAXIMUM HOPS number is decimal in the range 1-30.This parameter is only applicable if the executor node is of type AREA.'
Status: mandatory Access: read-write
OBJECT-TYPE    
  INTEGER aminhops(1), amaxhops(30)  

wfivRouteMaxArea 1.3.6.1.4.1.18.3.5.2.1.15
'This value represents the largest area number and, therefore, number of areas that can be known about by the executor node's Routing. This parameter is only applicable if the executor node is of type AREA. The number is an integer in the range 1-63.'
Status: mandatory Access: read-write
OBJECT-TYPE    
  INTEGER minarea(1), maxarea(63)  

wfivRouteType 1.3.6.1.4.1.18.3.5.2.1.16
'This parameter indicates the type of the executor node. The node-type is one of the following: ROUTING III NONROUTING III ROUTING IV NONROUTING IV AREA A routing node has full routing capability. A nonrouting node contains a subset of the Routing modules. The III and IV indicate the DNA phase of the node. Nonrouting nodes can deliver and receive packets to and from any node, but cannot route packets from other nodes through to other nodes. An area node routes between areas. Refer to the Routing specification for details. For adjacent nodes, this is a read-only parameter that indicates the type of the reachable adjacent node. NOTE: The ROUTING III and NONROUTING III values are incremented by one compared to the standard DECnet values in order to maintain compliance with RFC 1155)'
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER area(3), routingiv(4), nonroutingiv(5)  

wfivCircuitTable 1.3.6.1.4.1.18.3.5.2.2
' Table of DECnet Circuit Configuration and Counter Records'
Status: mandatory Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    WfivCircuitEntry

wfivCircuitEntry 1.3.6.1.4.1.18.3.5.2.2.1
'Parameters information about all circuits currently known. NOTE: depending on the type of object being querried (e.g., a level 1 vs. a level 2 router or end system) some variables may not be present.'
Status: mandatory Access: not-accessible
OBJECT-TYPE    
  WfivCircuitEntry  

wfivCircuitCreateDelete 1.3.6.1.4.1.18.3.5.2.2.1.1
'This value determines whether the circuit is configured'
Status: mandatory Access: read-write
OBJECT-TYPE    
  INTEGER create(1), delete(2)  

wfivCircuitEnableDisable 1.3.6.1.4.1.18.3.5.2.2.1.2
'This value represents the circuit's Network Management operational state. NOTE: These values are incremented by one compared to the standard DECnet values in order to maintain compliance with RFC 1155.'
Status: mandatory Access: read-write
OBJECT-TYPE    
  INTEGER enable(1), disable(2)  

wfivCircuitCommonState 1.3.6.1.4.1.18.3.5.2.2.1.3
'This value represents the circuit's operational state.'
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER notpresent(4), initializing(3), down(2), up(1)  

wfivCircuitArea 1.3.6.1.4.1.18.3.5.2.2.1.4
'DECnet Phase IV area number for this circuit.'
Status: mandatory Access: read-write
OBJECT-TYPE    
  INTEGER minarea(1), defarea(1), maxarea(63)  

wfivCircuitNodeid 1.3.6.1.4.1.18.3.5.2.2.1.5
'DECnet Phase IV node address for this circuit.'
Status: mandatory Access: read-write
OBJECT-TYPE    
  INTEGER minnodeid(1), defnodeid(1), maxnodeid(1023)  

wfivCircuitNodeAddr 1.3.6.1.4.1.18.3.5.2.2.1.6
'The address of the adjacent node.'
Status: mandatory Access: read-only
OBJECT-TYPE    
  DisplayString  

wfivCircuitID 1.3.6.1.4.1.18.3.5.2.2.1.7
'A unique value for each known circuit.'
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER  

wfivCircuitCommonType 1.3.6.1.4.1.18.3.5.2.2.1.8
'Represents the type of the circuit. For X.25 circuits, the value must be set to X25. For DDCMP and Ethernet circuits it is read only and is the same value as the protocol of the associated line. NOTE: Values 1 - 5 are incremented by one compared to the standard DECnet values in order to maintain compliance with RFC 1155.'
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER sync(1), x25(4), ethernet(6), fddi(15), smds(100), fr(101)  

wfivCircuitExecCost 1.3.6.1.4.1.18.3.5.2.2.1.9
'This value represents the Routing cost of the circuit. Routing routes messages along the path between two nodes having the smallest cost. The cost is a decimal integer in the range 1-63.'
Status: mandatory Access: read-write
OBJECT-TYPE    
  INTEGER mincost(1), defcost(10), maxcost(63)  

wfivCircuitExecHelloTimer 1.3.6.1.4.1.18.3.5.2.2.1.10
'This value determines the frequency of Routing Hello (T3) messages sent to the adjacent node on the circuit. Seconds is a decimal integer in the range 1-8191.'
Status: mandatory Access: read-write
OBJECT-TYPE    
  INTEGER hellomin(1), hellodef(15), hellomax(8191)  

wfivCircuitDesigRouterNodeAddr 1.3.6.1.4.1.18.3.5.2.2.1.11
'This value is the address of the designated router.'
Status: mandatory Access: read-only
OBJECT-TYPE    
  DisplayString  

wfivCircuitMaxRouters 1.3.6.1.4.1.18.3.5.2.2.1.12
'NR -This parameter is the maximum number of routers (including the executor itself) allowed on the circuit by Routing for circuits that are owned by the executor node. Number is a decimal integer in the range 1-33.'
Status: mandatory Access: read-write
OBJECT-TYPE    
  INTEGER maxroutersdef(33), maxroutersmax(33)  

wfivCircuitRouterPri 1.3.6.1.4.1.18.3.5.2.2.1.13
'This parameter is the priority that this router is to have in the selection of designated router for the circuit on circuits that are owned by the executor node. Number is a decimal integer in the range 0-127. The default value is 64.'
Status: mandatory Access: read-write
OBJECT-TYPE    
  INTEGER routerpridef(64), routerprimax(127)  

wfivCircuitCountAgedPktLoss 1.3.6.1.4.1.18.3.5.2.2.1.14
'Aged packet loss.'
Status: mandatory Access: read-only
OBJECT-TYPE    
  Counter  

wfivCircuitCountNodeUnrPktLoss 1.3.6.1.4.1.18.3.5.2.2.1.15
'Node unreachable packet loss.'
Status: mandatory Access: read-only
OBJECT-TYPE    
  Counter  

wfivCircuitCountOutRngePktLoss 1.3.6.1.4.1.18.3.5.2.2.1.16
'Node out-of-range packet loss.'
Status: mandatory Access: read-only
OBJECT-TYPE    
  Counter  

wfivCircuitCountOverSzePktLoss 1.3.6.1.4.1.18.3.5.2.2.1.17
'Oversized packet loss.'
Status: mandatory Access: read-only
OBJECT-TYPE    
  Counter  

wfivCircuitCountPacketFmtErr 1.3.6.1.4.1.18.3.5.2.2.1.18
'Packet format errors.'
Status: mandatory Access: read-only
OBJECT-TYPE    
  Counter  

wfivCircuitCountPtlRteUpdtLoss 1.3.6.1.4.1.18.3.5.2.2.1.19
'Partial routing update loss.'
Status: mandatory Access: read-only
OBJECT-TYPE    
  Counter  

wfivCircuitCountTransitPksRecd 1.3.6.1.4.1.18.3.5.2.2.1.20
'Transit packets Received. This value is stored internally as a 32 bit value.'
Status: mandatory Access: read-only
OBJECT-TYPE    
  Counter  

wfivCircuitCountTransitPkSent 1.3.6.1.4.1.18.3.5.2.2.1.21
'Transit packets sent. This value is stored internally as a 32 bit value.'
Status: mandatory Access: read-only
OBJECT-TYPE    
  Counter  

wfivCircuitCountRtHelloSent 1.3.6.1.4.1.18.3.5.2.2.1.22
' Router Hellos Sent'
Status: mandatory Access: read-only
OBJECT-TYPE    
  Counter  

wfivCircuitCountRtHelloRcvd 1.3.6.1.4.1.18.3.5.2.2.1.23
' Router Hellos Received'
Status: mandatory Access: read-only
OBJECT-TYPE    
  Counter  

wfivCircuitCountHelloSent 1.3.6.1.4.1.18.3.5.2.2.1.24
' Endnode Hellos Sent'
Status: mandatory Access: read-only
OBJECT-TYPE    
  Counter  

wfivCircuitCountHelloRcvd 1.3.6.1.4.1.18.3.5.2.2.1.25
' Endnode Hellos Received'
Status: mandatory Access: read-only
OBJECT-TYPE    
  Counter  

wfivCircuitCountL1UpdSent 1.3.6.1.4.1.18.3.5.2.2.1.26
' Level 1 Routing Updates Sent'
Status: mandatory Access: read-only
OBJECT-TYPE    
  Counter  

wfivCircuitCountL1UpdRcvd 1.3.6.1.4.1.18.3.5.2.2.1.27
' Level 1 Routing Updates Received'
Status: mandatory Access: read-only
OBJECT-TYPE    
  Counter  

wfivCircuitCountAreaUpdSent 1.3.6.1.4.1.18.3.5.2.2.1.28
' Area Routing Updates Sent'
Status: mandatory Access: read-only
OBJECT-TYPE    
  Counter  

wfivCircuitCountAreaUpdRcvd 1.3.6.1.4.1.18.3.5.2.2.1.29
' Area Routing Updates Received'
Status: mandatory Access: read-only
OBJECT-TYPE    
  Counter  

wfivCircuitCountDropped 1.3.6.1.4.1.18.3.5.2.2.1.30
' Dropped Packets '
Status: mandatory Access: read-only
OBJECT-TYPE    
  Counter  

wfivCircuitAllEndnodesMac 1.3.6.1.4.1.18.3.5.2.2.1.31
'This parameter can be used to assign the AllEndnodes multicast MAC address value for use over WAN media (e.g. Frame Relay).'
Status: mandatory Access: read-write
OBJECT-TYPE    
  OCTET STRING  

wfivCircuitAllRoutersMac 1.3.6.1.4.1.18.3.5.2.2.1.32
'This parameter can be used to assign the AllRouters multicast MAC address value for use over WAN media (e.g. Frame Relay).'
Status: mandatory Access: read-write
OBJECT-TYPE    
  OCTET STRING  

wfivCircuitAllAreaRoutersMac 1.3.6.1.4.1.18.3.5.2.2.1.33
'This parameter can be used to assign the AllAreaRouters multicast MAC address value for use over WAN media (e.g. Frame Relay).'
Status: mandatory Access: read-write
OBJECT-TYPE    
  OCTET STRING  

wfivCircuitHelloEnableDisable 1.3.6.1.4.1.18.3.5.2.2.1.34
' This parameter is used to disable to sending of Hellos to Endnodes. It would be used in conjunction with Static Adjacencies to limit the amount of data passed over a WAN link (e.g. Frame Relay).'
Status: mandatory Access: read-write
OBJECT-TYPE    
  INTEGER enable(1), disable(2)  

wfivCircuitRtHelloEnableDisable 1.3.6.1.4.1.18.3.5.2.2.1.35
' This parameter is used to disable to sending of Hellos to Routers. It would be used in conjunction with Static Adjacencies to limit the amount of data passed over a WAN link (e.g. Frame Relay).'
Status: mandatory Access: read-write
OBJECT-TYPE    
  INTEGER enable(1), disable(2)  

wfivCircuitL1UpdateEnableDisable 1.3.6.1.4.1.18.3.5.2.2.1.36
' This parameter is used to disable to sending of Level 1 topology updates. It would be used in conjunction with Static Adjacencies to limit the amount of data passed over a WAN link (e.g. Frame Relay).'
Status: mandatory Access: read-write
OBJECT-TYPE    
  INTEGER enable(1), disable(2)  

wfivLevel1RouteTable 1.3.6.1.4.1.18.3.5.2.3
' Table of Level 1 Routing Table Entries'
Status: mandatory Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    WfivLevel1RouteEntry

wfivLevel1RouteEntry 1.3.6.1.4.1.18.3.5.2.3.1
'A Record in the Level 1 Routing Table'
Status: mandatory Access: not-accessible
OBJECT-TYPE    
  WfivLevel1RouteEntry  

wfivLevel1AreaId 1.3.6.1.4.1.18.3.5.2.3.1.1
'Area Id for this node'
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER  

wfivLevel1NodeId 1.3.6.1.4.1.18.3.5.2.3.1.2
'Area Id for this node'
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER  

wfivLevel1RouteNodeAddr 1.3.6.1.4.1.18.3.5.2.3.1.3
'This value is the address of the node about which routing information is contained in this level 1 routing table.'
Status: mandatory Access: read-only
OBJECT-TYPE    
  DisplayString  

wfivLevel1RouteCircuitID 1.3.6.1.4.1.18.3.5.2.3.1.4
'This READ_ONLY parameter identifies the circuit used to get to a remote node. Circuit-id is an id-string. This parameter can be used when displaying a list of nodes to indicate that the display is to be restricted to those nodes adjacent on the specified circuit.'
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER  

wfivLevel1RouteCost 1.3.6.1.4.1.18.3.5.2.3.1.5
'This READ_ONLY parameter represents the total cost over the current path to the destination node. Cost is a positive integer value associated with using a circuit. Routing routes messages (data) along the path between two nodes with the smallest cost. COST is kept on a remote node basis.'
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER  

wfivLevel1RouteHops 1.3.6.1.4.1.18.3.5.2.3.1.6
'This READ_ONLY parameter represents the number of hops over to a destination node. A hop is Routing value representing the logical distance between two nodes in a network. HOPS is kept on a remote node basis.'
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER  

wfivLevel1RouteNextNode 1.3.6.1.4.1.18.3.5.2.3.1.7
'This READ_ONLY value indicates the next node on the circuit used to get to the node under scrutiny (next hop).'
Status: mandatory Access: read-only
OBJECT-TYPE    
  DisplayString  

wfivAreaTable 1.3.6.1.4.1.18.3.5.2.4
'Table of Area Routing Table Entries'
Status: mandatory Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    WfivAreaEntry

wfivAreaEntry 1.3.6.1.4.1.18.3.5.2.4.1
'The area routing information.'
Status: mandatory Access: not-accessible
OBJECT-TYPE    
  WfivAreaEntry  

wfivAreaNum 1.3.6.1.4.1.18.3.5.2.4.1.1
'This value indicates the area number of this entry.'
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER  

wfivAreaState 1.3.6.1.4.1.18.3.5.2.4.1.2
'This value indicates the state of the area'
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER reachable(4), unreachable(5)  

wfivAreaCost 1.3.6.1.4.1.18.3.5.2.4.1.3
'The total cost over the current path to the destination area. Cost is a value associated with using a circuit. Routing routes messages (data) along the path between 2 areas with the smallest cost.'
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER  

wfivAreaHops 1.3.6.1.4.1.18.3.5.2.4.1.4
'The number of hops to a destination area. A hop is the routing value representing the logical distance between two areas in network.'
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER  

wfivAreaCircuitID 1.3.6.1.4.1.18.3.5.2.4.1.5
'The circuit used to get to the remote area'
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER  

wfivAreaNextNode 1.3.6.1.4.1.18.3.5.2.4.1.6
'The next node on the circuit used to get to the area under scrutiny.'
Status: mandatory Access: read-only
OBJECT-TYPE    
  DisplayString  

wfivAdjTable 1.3.6.1.4.1.18.3.5.2.5
Adjacency Table
Status: mandatory Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    WfivAdjEntry

wfivAdjEntry 1.3.6.1.4.1.18.3.5.2.5.1
' Adjacency Table - the real index is the adjacency index'
Status: mandatory Access: not-accessible
OBJECT-TYPE    
  WfivAdjEntry  

wfivAdjIndex 1.3.6.1.4.1.18.3.5.2.5.1.1
'Index in the Adjacency Table'
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER  

wfivAdjNodeAddr 1.3.6.1.4.1.18.3.5.2.5.1.2
'The address of the adjacent node.'
Status: mandatory Access: read-only
OBJECT-TYPE    
  DisplayString  

wfivAdjBlockSize 1.3.6.1.4.1.18.3.5.2.5.1.3
'This READ_ONLY parameter is the block size that was negotiated with the adjacent Routing layer during Routing initialization over a particular circuit. It includes the routing header, but excludes the data link header. This parameter is qualified by ADJACENT NODE.'
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER  

wfivAdjListenTimer 1.3.6.1.4.1.18.3.5.2.5.1.4
'This READ_ONLY value determines the maximum time allowed to elapse before Routing receives some message (either a Hello message or a user message) from the adjacent node on the circuit. It was agreed during Routing initialization with the adjacent Routing layer. Seconds is a decimal integer in the range 1-65535. This parameter is qualified by ADJACENT NODE.'
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER  

wfivAdjCircuitID 1.3.6.1.4.1.18.3.5.2.5.1.5
'A unique value for each known circuit.'
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER  

wfivAdjType 1.3.6.1.4.1.18.3.5.2.5.1.6
'This parameter indicates the type of adjacency. For adjacent nodes, this is a READ_ONLY parameter that indicates the type of the reachable adjacent node. NOTE: The ROUTING III and NONROUTING III values are incremented by one compared to the standard DECnet values in order to maintain compliance with RFC 1155) ROUTING III (1), NONROUTING III (2), AREA (3), ROUTING IV (4), NONROUTING IV (5)'
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER  

wfivAdjState 1.3.6.1.4.1.18.3.5.2.5.1.7
'This value indicates the state of a router adjacency. On adjacencies over a circuit of type (wfivCircuitCommonType) Ethernet, CI, or FDDI, with an adjacent node of type (wfivAdjType) ROUTING IV or AREA, this variable is the state of the Ethernet Initialization Layer for this adjacency, and can have values INITIALIZING or UP. (See Section 9.1.1 of DECnet Phase IV Routing Layer Functional Specification.) On adjacencies over a circuit of type (wfivCircuitCommonType) Ethernet, CI, or FDDI, with an adjacent node of type (wfivAdjType) NONROUTING IV, this varaible will always take on the value UP. On adjacencies over a circuit of type (wfivCircuitCommonType) DDCMP POINT, DDCMP CONTROL, DDCMP TRIBUTARY, DDCMP DMC, or X.25, this variable is the state of the Routing Layer Initialization Circuit State. (See section 7.3, ibid.) It can have values between RUN and HALT. On adjacencies over a circuit of type (wfivCircuitCommonType) OTHER, this variable may be used in a manner consistent with the Initialization Layer used on that circuit. INITIALIZING (1), -- Ethernet one-way UP (2), -- Ethernet two-way RUN (3), -- The eight DDCMP/X.25 states CIRCUIT REJECTED (4), DATA LINK START (5), ROUTING LAYER INITIALIZE (6), ROUTING LAYER VERIFY (7), ROUTING LAYER COMPLETE (8), OFF (9), HALT (10)'
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER init(1), up(2)  

wfivAdjPriority 1.3.6.1.4.1.18.3.5.2.5.1.8
'Priority assigned by the adjacent node for this circuit.'
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER  

wfivAdjClass 1.3.6.1.4.1.18.3.5.2.5.1.9
'Specifies whether this adjacency is Static or Dynamic'
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER  

wfivTrafficFilterTable 1.3.6.1.4.1.18.3.5.2.6
DECNET Traffic Filters
Status: mandatory Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    WfivTrafficFilterEntry

wfivTrafficFilterEntry 1.3.6.1.4.1.18.3.5.2.6.1
An entry in WfivTrafficFilterTable.
Status: mandatory Access: not-accessible
OBJECT-TYPE    
  WfivTrafficFilterEntry  

wfivTrafficFilterCreate 1.3.6.1.4.1.18.3.5.2.6.1.1
Defines the existence of the traffic filter rule: created - traffic filter exists delete - traffic filter does not exist and can be deleted.
Status: mandatory Access: read-write
OBJECT-TYPE    
  INTEGER created(1), deleted(2)  

wfivTrafficFilterEnable 1.3.6.1.4.1.18.3.5.2.6.1.2
Defines whether or not the traffic filter rule should be used: enabled - activate the rule. disabled - inactivate the rule.
Status: mandatory Access: read-write
OBJECT-TYPE    
  INTEGER enabled(1), disabled(2)  

wfivTrafficFilterStatus 1.3.6.1.4.1.18.3.5.2.6.1.3
Defines the current status of the traffic filter: inactive - the rule is not in use. active - the rule is being used. error - the application detected an error in the rule.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER active(1), error(2), inactive(3)  

wfivTrafficFilterCounter 1.3.6.1.4.1.18.3.5.2.6.1.4
The number of received packets that have matched this rule.
Status: mandatory Access: read-only
OBJECT-TYPE    
  Counter  

wfivTrafficFilterDefinition 1.3.6.1.4.1.18.3.5.2.6.1.5
The filter rule definition.
Status: mandatory Access: read-write
OBJECT-TYPE    
  Opaque  

wfivTrafficFilterReserved 1.3.6.1.4.1.18.3.5.2.6.1.6
Reserved field.
Status: mandatory Access: not-accessible
OBJECT-TYPE    
  INTEGER  

wfivTrafficFilterCircuit 1.3.6.1.4.1.18.3.5.2.6.1.7
The ID of the Circuit to which the filter is applied.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER  

wfivTrafficFilterRuleNumber 1.3.6.1.4.1.18.3.5.2.6.1.8
ID for the rule.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER  

wfivTrafficFilterFragment 1.3.6.1.4.1.18.3.5.2.6.1.9
Fragment number - for large rules.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER  

wfivStaticAdjTable 1.3.6.1.4.1.18.3.5.2.7
Static Adjacency Table
Status: mandatory Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    WfivStaticAdjEntry

wfivStaticAdjEntry 1.3.6.1.4.1.18.3.5.2.7.1
' Static Adjacency Table '
Status: mandatory Access: not-accessible
OBJECT-TYPE    
  WfivStaticAdjEntry  

wfivStaticAdjCreateDelete 1.3.6.1.4.1.18.3.5.2.7.1.1
'This value determines whether the static adjacency is configured'
Status: mandatory Access: read-write
OBJECT-TYPE    
  INTEGER create(1), delete(2)  

wfivStaticAdjEnableDisable 1.3.6.1.4.1.18.3.5.2.7.1.2
'This value determines whether the static adjacency is active '
Status: mandatory Access: read-write
OBJECT-TYPE    
  INTEGER enable(1), disable(2)  

wfivStaticAdjArea 1.3.6.1.4.1.18.3.5.2.7.1.3
'DECnet Phase IV area number for this static Adjacency.'
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER  

wfivStaticAdjNodeid 1.3.6.1.4.1.18.3.5.2.7.1.4
'DECnet Phase IV node address for this static adjacency.'
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER  

wfivStaticAdjCircuitID 1.3.6.1.4.1.18.3.5.2.7.1.5
'The circuit used for this static adjacency.'
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER  

wfivStaticAdjNodeAddr 1.3.6.1.4.1.18.3.5.2.7.1.6
'The address of the adjacent node in display format.'
Status: mandatory Access: read-only
OBJECT-TYPE    
  DisplayString  

wfivStaticAdjType 1.3.6.1.4.1.18.3.5.2.7.1.7
' Specifies whether the static adjacency is to a router or end station.'
Status: mandatory Access: read-write
OBJECT-TYPE    
  INTEGER area(3), routingiv(4), nonroutingiv(5)  

wfivStaticAdjPriority 1.3.6.1.4.1.18.3.5.2.7.1.8
' Specifies the priority of the static adjacency if it's a router.'
Status: mandatory Access: read-write
OBJECT-TYPE    
  INTEGER  

wfivStaticAdjDestMACAddr 1.3.6.1.4.1.18.3.5.2.7.1.9
' Specifies the destination MAC address of the Static Adjacency if the circuit type is Frame Relay or SMDS.'
Status: mandatory Access: read-write
OBJECT-TYPE    
  OCTET STRING  

wfDs1Config 1.3.6.1.4.1.18.3.4.12.1
The DS1 Configuration table
Status: mandatory Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    WfDs1ConfigEntry

wfDs1ConfigEntry 1.3.6.1.4.1.18.3.4.12.1.1
per circuit DS1 configuration objects; wfDs1LineIndex corresponds to Wellfleet circuit number
Status: mandatory Access: not-accessible
OBJECT-TYPE    
  WfDs1ConfigEntry  

wfDs1LineIndex 1.3.6.1.4.1.18.3.4.12.1.1.1
this corresponds to the Wellfleet circuit number
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER minimum(1), maximum(1024)  

wfDs1TimeElapsed 1.3.6.1.4.1.18.3.4.12.1.1.2
1..900 seconds within the current 15-minute interval
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER  

wfDs1ValidIntervals 1.3.6.1.4.1.18.3.4.12.1.1.3
0..96 previous intervals that valid data were collected. This is 96 unless the CSU device was brought on line within the last 24 hours.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER  

wfDs1LineType 1.3.6.1.4.1.18.3.4.12.1.1.4
the variety of DS1 implementing this circuit
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER ds1ansi-esf(4)  

wfDs1ZeroCoding 1.3.6.1.4.1.18.3.4.12.1.1.5
the variety of Zero Code Suppression used on the link
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER ds1b8zs(2), ds1zbtsi(5)  

wfDs1SendCode 1.3.6.1.4.1.18.3.4.12.1.1.6
the type of code being sent across the DS1 circuit by the CSU
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER ds1sendnocode(2)  

wfDs1CircuitIdentifier 1.3.6.1.4.1.18.3.4.12.1.1.7
the transmission vendor's circuit identifier
Status: mandatory Access: read-only
OBJECT-TYPE    
  DisplayString  

wfDs1LoopbackConfig 1.3.6.1.4.1.18.3.4.12.1.1.8
the loopback state of the CSU
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER ds1noloop(1), ds1mgrpayloadloop(2), ds1mgrlineloop(3), ds1netreqpayloadloop(4), ds1netreqlineloop(5), ds1otherloop(6)  

wfDs1LineStatus 1.3.6.1.4.1.18.3.4.12.1.1.9
the state of the DS1 line
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER ds1noalarm(1), ds1farendalarm(2), ds1alarmindicationsignal(4), ds1lossofframe(8), ds1lossofsignal(16), ds1loopbackstate(32)  

wfDs1Current 1.3.6.1.4.1.18.3.4.12.2
The DS1 Current table
Status: mandatory Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    WfDs1CurrentEntry

wfDs1CurrentEntry 1.3.6.1.4.1.18.3.4.12.2.1
per circuit DS1 current objects - wfDs1CurrentIndex corresponds to Wellfleet circuit number
Status: mandatory Access: not-accessible
OBJECT-TYPE    
  WfDs1CurrentEntry  

wfDs1CurrentIndex 1.3.6.1.4.1.18.3.4.12.2.1.1
this corresponds to the Wellfleet circuit number
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER minimum(1), maximum(1024)  

wfDs1CurrentESs 1.3.6.1.4.1.18.3.4.12.2.1.2
the count of errored seconds in the current interval
Status: mandatory Access: read-only
OBJECT-TYPE    
  Counter  

wfDs1CurrentSESs 1.3.6.1.4.1.18.3.4.12.2.1.3
the count of severely errored seconds in the current interval
Status: mandatory Access: read-only
OBJECT-TYPE    
  Counter  

wfDs1CurrentSEFs 1.3.6.1.4.1.18.3.4.12.2.1.4
the count of severely errored framing seconds in the current interval
Status: mandatory Access: read-only
OBJECT-TYPE    
  Counter  

wfDs1CurrentUASs 1.3.6.1.4.1.18.3.4.12.2.1.5
the number of unavailable seconds in the current interval
Status: mandatory Access: read-only
OBJECT-TYPE    
  Counter  

wfDs1CurrentBPVs 1.3.6.1.4.1.18.3.4.12.2.1.6
the count of bipolar violations in the current interval
Status: mandatory Access: read-only
OBJECT-TYPE    
  Counter  

wfDs1CurrentCVs 1.3.6.1.4.1.18.3.4.12.2.1.7
the count of code violation error events in the current interval
Status: mandatory Access: read-only
OBJECT-TYPE    
  Counter  

wfDs1Interval 1.3.6.1.4.1.18.3.4.12.3
The DS1 Interval table
Status: mandatory Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    WfDs1IntervalEntry

wfDs1IntervalEntry 1.3.6.1.4.1.18.3.4.12.3.1
per circuit DS1 interval objects - wfDs1IntervalIndex corresponds to Wellfleet circuit number, wfDs1IntervalNumber is the numbered previous 15-minute interval
Status: mandatory Access: not-accessible
OBJECT-TYPE    
  WfDs1IntervalEntry  

wfDs1IntervalIndex 1.3.6.1.4.1.18.3.4.12.3.1.1
this corresponds to the Wellfleet circuit number
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER minimum(1), maximum(1024)  

wfDs1IntervalNumber 1.3.6.1.4.1.18.3.4.12.3.1.2
1..96 where 1 is the most recent 15-minute interval and 96 is the least
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER minimum(1), maximum(96)  

wfDs1IntervalESs 1.3.6.1.4.1.18.3.4.12.3.1.3
the count of errored seconds in the specified interval
Status: mandatory Access: read-only
OBJECT-TYPE    
  Gauge  

wfDs1IntervalSESs 1.3.6.1.4.1.18.3.4.12.3.1.4
the count of severely errored seconds in the specified interval
Status: mandatory Access: read-only
OBJECT-TYPE    
  Gauge  

wfDs1IntervalSEFs 1.3.6.1.4.1.18.3.4.12.3.1.5
the count of severely errored framing seconds in the specified interval
Status: mandatory Access: read-only
OBJECT-TYPE    
  Gauge  

wfDs1IntervalUASs 1.3.6.1.4.1.18.3.4.12.3.1.6
the number of unavailable seconds in the specified interval
Status: mandatory Access: read-only
OBJECT-TYPE    
  Gauge  

wfDs1IntervalBPVs 1.3.6.1.4.1.18.3.4.12.3.1.7
the count of bipolar violations in the specified interval
Status: mandatory Access: read-only
OBJECT-TYPE    
  Gauge  

wfDs1IntervalCVs 1.3.6.1.4.1.18.3.4.12.3.1.8
the count of code violation error events in the specified interval
Status: mandatory Access: read-only
OBJECT-TYPE    
  Gauge  

wfDs1Total 1.3.6.1.4.1.18.3.4.12.4
The DS1 Total table
Status: mandatory Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    WfDs1TotalEntry

wfDs1TotalEntry 1.3.6.1.4.1.18.3.4.12.4.1
per circuit DS1 total objects - wfDs1TotalIndex corresponds to Wellfleet circuit number
Status: mandatory Access: not-accessible
OBJECT-TYPE    
  WfDs1TotalEntry  

wfDs1TotalIndex 1.3.6.1.4.1.18.3.4.12.4.1.1
this corresponds to the Wellfleet circuit number
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER minimum(1), maximum(1024)  

wfDs1TotalESs 1.3.6.1.4.1.18.3.4.12.4.1.2
total count of errored seconds
Status: mandatory Access: read-only
OBJECT-TYPE    
  Gauge  

wfDs1TotalSESs 1.3.6.1.4.1.18.3.4.12.4.1.3
total count of severely errored seconds
Status: mandatory Access: read-only
OBJECT-TYPE    
  Gauge  

wfDs1TotalSEFs 1.3.6.1.4.1.18.3.4.12.4.1.4
total count of severely errored framing seconds
Status: mandatory Access: read-only
OBJECT-TYPE    
  Gauge  

wfDs1TotalUASs 1.3.6.1.4.1.18.3.4.12.4.1.5
total number of unavailable seconds
Status: mandatory Access: read-only
OBJECT-TYPE    
  Gauge  

wfDs1TotalBPVs 1.3.6.1.4.1.18.3.4.12.4.1.6
total count of bipolar violations
Status: mandatory Access: read-only
OBJECT-TYPE    
  Gauge  

wfDs1TotalCVs 1.3.6.1.4.1.18.3.4.12.4.1.7
total count of code violation error events
Status: mandatory Access: read-only
OBJECT-TYPE    
  Gauge  

wfDs1FeCurrent 1.3.6.1.4.1.18.3.4.12.5
The DS1 Far End Current table
Status: mandatory Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    WfDs1FeCurrentEntry

wfDs1FeCurrentEntry 1.3.6.1.4.1.18.3.4.12.5.1
per circuit DS1 far end current objects wfDs1CurrentIndex corresponds to Wellfleet circuit number
Status: mandatory Access: not-accessible
OBJECT-TYPE    
  WfDs1FeCurrentEntry  

wfDs1FeCurrentIndex 1.3.6.1.4.1.18.3.4.12.5.1.1
this corresponds to the Wellfleet circuit number
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER minimum(1), maximum(1024)  

wfDs1FeCurrentESs 1.3.6.1.4.1.18.3.4.12.5.1.2
the count of errored seconds in the current interval
Status: mandatory Access: read-only
OBJECT-TYPE    
  Counter  

wfDs1FeCurrentSESs 1.3.6.1.4.1.18.3.4.12.5.1.3
the count of severely errored seconds in the current interval
Status: mandatory Access: read-only
OBJECT-TYPE    
  Counter  

wfDs1FeCurrentSEFs 1.3.6.1.4.1.18.3.4.12.5.1.4
the count of severely errored framing seconds in the current interval
Status: mandatory Access: read-only
OBJECT-TYPE    
  Counter  

wfDs1FeCurrentBPVs 1.3.6.1.4.1.18.3.4.12.5.1.5
the count of bipolar violations in the current interval
Status: mandatory Access: read-only
OBJECT-TYPE    
  Counter  

wfDs1FeCurrentCVs 1.3.6.1.4.1.18.3.4.12.5.1.6
the count of code violation error events in the current interval
Status: mandatory Access: read-only
OBJECT-TYPE    
  Counter  

wfDs1FeInterval 1.3.6.1.4.1.18.3.4.12.6
The DS1 Far End Interval table
Status: mandatory Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    WfDs1FeIntervalEntry

wfDs1FeIntervalEntry 1.3.6.1.4.1.18.3.4.12.6.1
per circuit DS1 far end interval objects - wfDs1FeIntervalIndex corresponds to Wellfleet circuit number, wfDs1FeIntervalNumber is the numbered previous 15-minute interval
Status: mandatory Access: not-accessible
OBJECT-TYPE    
  WfDs1FeIntervalEntry  

wfDs1FeIntervalIndex 1.3.6.1.4.1.18.3.4.12.6.1.1
this corresponds to the Wellfleet circuit number
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER minimum(1), maximum(1024)  

wfDs1FeIntervalNumber 1.3.6.1.4.1.18.3.4.12.6.1.2
1..96 where 1 is the most recent 15-minute interval and 96 is the least
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER minimum(1), maximum(96)  

wfDs1FeIntervalESs 1.3.6.1.4.1.18.3.4.12.6.1.3
the count of errored seconds in the specified interval
Status: mandatory Access: read-only
OBJECT-TYPE    
  Gauge  

wfDs1FeIntervalSESs 1.3.6.1.4.1.18.3.4.12.6.1.4
the count of severely errored seconds in the specified interval
Status: mandatory Access: read-only
OBJECT-TYPE    
  Gauge  

wfDs1FeIntervalSEFs 1.3.6.1.4.1.18.3.4.12.6.1.5
the count of severely errored framing seconds in the specified interval
Status: mandatory Access: read-only
OBJECT-TYPE    
  Gauge  

wfDs1FeIntervalBPVs 1.3.6.1.4.1.18.3.4.12.6.1.6
the count of bipolar violations in the specified interval
Status: mandatory Access: read-only
OBJECT-TYPE    
  Gauge  

wfDs1FeIntervalCVs 1.3.6.1.4.1.18.3.4.12.6.1.7
the count of code violation error events in the specified interval
Status: mandatory Access: read-only
OBJECT-TYPE    
  Gauge  

wfDs1FeTotal 1.3.6.1.4.1.18.3.4.12.7
The DS1 Far End Total table
Status: mandatory Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    WfDs1FeTotalEntry

wfDs1FeTotalEntry 1.3.6.1.4.1.18.3.4.12.7.1
per circuit DS1 far end total objects - wfDs1FeTotalIndex corresponds to Wellfleet circuit number
Status: mandatory Access: not-accessible
OBJECT-TYPE    
  WfDs1FeTotalEntry  

wfDs1FeTotalIndex 1.3.6.1.4.1.18.3.4.12.7.1.1
this corresponds to the Wellfleet circuit number
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER minimum(1), maximum(1024)  

wfDs1FeTotalESs 1.3.6.1.4.1.18.3.4.12.7.1.2
total count of errored seconds
Status: mandatory Access: read-only
OBJECT-TYPE    
  Gauge  

wfDs1FeTotalSESs 1.3.6.1.4.1.18.3.4.12.7.1.3
total count of severely errored seconds
Status: mandatory Access: read-only
OBJECT-TYPE    
  Gauge  

wfDs1FeTotalSEFs 1.3.6.1.4.1.18.3.4.12.7.1.4
total count of severely errored framing seconds
Status: mandatory Access: read-only
OBJECT-TYPE    
  Gauge  

wfDs1FeTotalBPVs 1.3.6.1.4.1.18.3.4.12.7.1.5
total count of bipolar violations
Status: mandatory Access: read-only
OBJECT-TYPE    
  Gauge  

wfDs1FeTotalCVs 1.3.6.1.4.1.18.3.4.12.7.1.6
total count of code violation error events
Status: mandatory Access: read-only
OBJECT-TYPE    
  Gauge  

wfDs3Config 1.3.6.1.4.1.18.3.4.13.1
The DS3 Configuration table
Status: mandatory Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    WfDs3ConfigEntry

wfDs3ConfigEntry 1.3.6.1.4.1.18.3.4.13.1.1
per circuit DS3 configuration objects; wfDs3LineIndex corresponds to Wellfleet circuit number
Status: mandatory Access: not-accessible
OBJECT-TYPE    
  WfDs3ConfigEntry  

wfDs3LineIndex 1.3.6.1.4.1.18.3.4.13.1.1.1
this corresponds to the Wellfleet circuit number
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER minimum(1), maximum(1024)  

wfDs3TimeElapsed 1.3.6.1.4.1.18.3.4.13.1.1.2
1..900 seconds within the current 15-minute interval
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER  

wfDs3ValidIntervals 1.3.6.1.4.1.18.3.4.13.1.1.3
0..96 previous intervals that valid data were collected. This is 96 unless the CSU device was brought on line within the last 24 hours.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER  

wfDs3LineType 1.3.6.1.4.1.18.3.4.13.1.1.4
the variety of DS3 implementing this circuit
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER other(1), ds3cbitparity(4), ds3clearchannel(5)  

wfDs3ZeroCoding 1.3.6.1.4.1.18.3.4.13.1.1.5
the variety of Zero Code Suppression used on the link
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER ds3b3zs(2)  

wfDs3SendCode 1.3.6.1.4.1.18.3.4.13.1.1.6
the type of code being sent across the DS3 circuit by the CSU
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER ds3sendnocode(2)  

wfDs3CircuitIdentifier 1.3.6.1.4.1.18.3.4.13.1.1.7
the transmission vendor's circuit identifier
Status: mandatory Access: read-only
OBJECT-TYPE    
  DisplayString  

wfDs3LoopbackConfig 1.3.6.1.4.1.18.3.4.13.1.1.8
the loopback state of the CSU
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER ds3noloop(1), ds3mgrpayloadloop(2), ds3mgrlineloop(3), ds3netreqpayloadloop(4), ds3netreqlineloop(5), ds3otherloop(6)  

wfDs3LineStatus 1.3.6.1.4.1.18.3.4.13.1.1.9
the state of the DS3 line
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER ds3noalarm(1), ds3farendalarm(2), ds3alarmindicationsignal(4), ds3lossofframe(8), ds3lossofsignal(16), ds3loopbackstate(32)  

wfDs3Current 1.3.6.1.4.1.18.3.4.13.2
The DS3 Current table
Status: mandatory Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    WfDs3CurrentEntry

wfDs3CurrentEntry 1.3.6.1.4.1.18.3.4.13.2.1
per circuit DS3 current objects - wfDs3CurrentIndex corresponds to Wellfleet circuit number
Status: mandatory Access: not-accessible
OBJECT-TYPE    
  WfDs3CurrentEntry  

wfDs3CurrentIndex 1.3.6.1.4.1.18.3.4.13.2.1.1
this corresponds to the Wellfleet circuit number
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER minimum(1), maximum(1024)  

wfDs3CurrentESs 1.3.6.1.4.1.18.3.4.13.2.1.2
the count of errored seconds in the current interval
Status: mandatory Access: read-only
OBJECT-TYPE    
  Counter  

wfDs3CurrentSESs 1.3.6.1.4.1.18.3.4.13.2.1.3
the count of severely errored seconds in the current interval
Status: mandatory Access: read-only
OBJECT-TYPE    
  Counter  

wfDs3CurrentSEFs 1.3.6.1.4.1.18.3.4.13.2.1.4
the count of severely errored framing seconds in the current interval
Status: mandatory Access: read-only
OBJECT-TYPE    
  Counter  

wfDs3CurrentUASs 1.3.6.1.4.1.18.3.4.13.2.1.5
the number of unavailable seconds in the current interval
Status: mandatory Access: read-only
OBJECT-TYPE    
  Counter  

wfDs3CurrentBPVs 1.3.6.1.4.1.18.3.4.13.2.1.6
the count of bipolar violations in the current interval
Status: mandatory Access: read-only
OBJECT-TYPE    
  Counter  

wfDs3CurrentCVs 1.3.6.1.4.1.18.3.4.13.2.1.7
the count of code violation error events in the current interval
Status: mandatory Access: read-only
OBJECT-TYPE    
  Counter  

wfDs3Interval 1.3.6.1.4.1.18.3.4.13.3
The DS3 Interval table
Status: mandatory Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    WfDs3IntervalEntry

wfDs3IntervalEntry 1.3.6.1.4.1.18.3.4.13.3.1
per circuit DS3 interval objects - wfDs3IntervalIndex corresponds to Wellfleet circuit number, wfDs3IntervalNumber is the numbered previous 15-minute interval
Status: mandatory Access: not-accessible
OBJECT-TYPE    
  WfDs3IntervalEntry  

wfDs3IntervalIndex 1.3.6.1.4.1.18.3.4.13.3.1.1
this corresponds to the Wellfleet circuit number
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER minimum(1), maximum(1024)  

wfDs3IntervalNumber 1.3.6.1.4.1.18.3.4.13.3.1.2
1..96 where 1 is the most recent 15-minute interval and 96 is the least
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER minimum(1), maximum(96)  

wfDs3IntervalESs 1.3.6.1.4.1.18.3.4.13.3.1.3
the count of errored seconds in the specified interval
Status: mandatory Access: read-only
OBJECT-TYPE    
  Gauge  

wfDs3IntervalSESs 1.3.6.1.4.1.18.3.4.13.3.1.4
the count of severely errored seconds in the specified interval
Status: mandatory Access: read-only
OBJECT-TYPE    
  Gauge  

wfDs3IntervalSEFs 1.3.6.1.4.1.18.3.4.13.3.1.5
the count of severely errored framing seconds in the specified interval
Status: mandatory Access: read-only
OBJECT-TYPE    
  Gauge  

wfDs3IntervalUASs 1.3.6.1.4.1.18.3.4.13.3.1.6
the number of unavailable seconds in the specified interval
Status: mandatory Access: read-only
OBJECT-TYPE    
  Gauge  

wfDs3IntervalBPVs 1.3.6.1.4.1.18.3.4.13.3.1.7
the count of bipolar violations in the specified interval
Status: mandatory Access: read-only
OBJECT-TYPE    
  Gauge  

wfDs3IntervalCVs 1.3.6.1.4.1.18.3.4.13.3.1.8
the count of code violation error events in the specified interval
Status: mandatory Access: read-only
OBJECT-TYPE    
  Gauge  

wfDs3Total 1.3.6.1.4.1.18.3.4.13.4
The DS3 Total table
Status: mandatory Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    WfDs3TotalEntry

wfDs3TotalEntry 1.3.6.1.4.1.18.3.4.13.4.1
per circuit DS3 total objects - wfDs3TotalIndex corresponds to Wellfleet circuit number
Status: mandatory Access: not-accessible
OBJECT-TYPE    
  WfDs3TotalEntry  

wfDs3TotalIndex 1.3.6.1.4.1.18.3.4.13.4.1.1
this corresponds to the Wellfleet circuit number
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER minimum(1), maximum(1024)  

wfDs3TotalESs 1.3.6.1.4.1.18.3.4.13.4.1.2
total count of errored seconds
Status: mandatory Access: read-only
OBJECT-TYPE    
  Gauge  

wfDs3TotalSESs 1.3.6.1.4.1.18.3.4.13.4.1.3
total count of severely errored seconds
Status: mandatory Access: read-only
OBJECT-TYPE    
  Gauge  

wfDs3TotalSEFs 1.3.6.1.4.1.18.3.4.13.4.1.4
total count of severely errored framing seconds
Status: mandatory Access: read-only
OBJECT-TYPE    
  Gauge  

wfDs3TotalUASs 1.3.6.1.4.1.18.3.4.13.4.1.5
total number of unavailable seconds
Status: mandatory Access: read-only
OBJECT-TYPE    
  Gauge  

wfDs3TotalBPVs 1.3.6.1.4.1.18.3.4.13.4.1.6
total count of bipolar violations
Status: mandatory Access: read-only
OBJECT-TYPE    
  Gauge  

wfDs3TotalCVs 1.3.6.1.4.1.18.3.4.13.4.1.7
total count of code violation error events
Status: mandatory Access: read-only
OBJECT-TYPE    
  Gauge  

wfDs3FeConfig 1.3.6.1.4.1.18.3.4.13.5
The DS3 Far End Configuration table
Status: mandatory Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    WfDs3FeConfigEntry

wfDs3FeConfigEntry 1.3.6.1.4.1.18.3.4.13.5.1
per circuit DS3 far end config objects - wfDs3FeIntervalIndex corresponds to Wellfleet circuit number
Status: mandatory Access: not-accessible
OBJECT-TYPE    
  WfDs3FeConfigEntry  

wfDs3FeConfigIndex 1.3.6.1.4.1.18.3.4.13.5.1.1
this corresponds to the Wellfleet circuit number
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER minimum(1), maximum(1024)  

wfDs3FarEndEquipCode 1.3.6.1.4.1.18.3.4.13.5.1.2
equipment description code - C-bit parity only
Status: mandatory Access: read-write
OBJECT-TYPE    
  DisplayString  

wfDs3FarEndLocationIDCode 1.3.6.1.4.1.18.3.4.13.5.1.3
equipment location code - C-bit parity only
Status: mandatory Access: read-write
OBJECT-TYPE    
  DisplayString  

wfDs3FarEndFrameIDCode 1.3.6.1.4.1.18.3.4.13.5.1.4
code for the equipment location within a building
Status: mandatory Access: read-write
OBJECT-TYPE    
  DisplayString  

wfDs3FarEndUnitCode 1.3.6.1.4.1.18.3.4.13.5.1.5
code for the equipment location within a bay
Status: mandatory Access: read-write
OBJECT-TYPE    
  DisplayString  

wfDs3FarEndFacilityIDCode 1.3.6.1.4.1.18.3.4.13.5.1.6
path identification code
Status: mandatory Access: read-write
OBJECT-TYPE    
  DisplayString  

wfDs3FeCurrent 1.3.6.1.4.1.18.3.4.13.6
The DS3 Far End Current table
Status: mandatory Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    WfDs3FeCurrentEntry

wfDs3FeCurrentEntry 1.3.6.1.4.1.18.3.4.13.6.1
per circuit DS3 far end current objects wfDs3FeCurrentIndex corresponds to Wellfleet circuit number
Status: mandatory Access: not-accessible
OBJECT-TYPE    
  WfDs3FeCurrentEntry  

wfDs3FeCurrentIndex 1.3.6.1.4.1.18.3.4.13.6.1.1
this corresponds to the Wellfleet circuit number
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER minimum(1), maximum(1024)  

wfDs3FeCurrentESs 1.3.6.1.4.1.18.3.4.13.6.1.2
the count of errored seconds in the current interval
Status: mandatory Access: read-only
OBJECT-TYPE    
  Counter  

wfDs3FeCurrentSESs 1.3.6.1.4.1.18.3.4.13.6.1.3
the count of severely errored seconds in the current interval
Status: mandatory Access: read-only
OBJECT-TYPE    
  Counter  

wfDs3FeCurrentCVs 1.3.6.1.4.1.18.3.4.13.6.1.4
the count of code violation error events in the current interval
Status: mandatory Access: read-only
OBJECT-TYPE    
  Counter  

wfDs3FeInterval 1.3.6.1.4.1.18.3.4.13.7
The DS3 Far End Interval table
Status: mandatory Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    WfDs3FeIntervalEntry

wfDs3FeIntervalEntry 1.3.6.1.4.1.18.3.4.13.7.1
per circuit DS3 far end interval objects - wfDs3FeIntervalIndex corresponds to Wellfleet circuit number, wfDs3FeIntervalNumber is the numbered previous 15-minute interval
Status: mandatory Access: not-accessible
OBJECT-TYPE    
  WfDs3FeIntervalEntry  

wfDs3FeIntervalIndex 1.3.6.1.4.1.18.3.4.13.7.1.1
this corresponds to the Wellfleet circuit number
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER minimum(1), maximum(1024)  

wfDs3FeIntervalNumber 1.3.6.1.4.1.18.3.4.13.7.1.2
1..96 where 1 is the most recent 15-minute interval and 96 is the least
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER minimum(1), maximum(96)  

wfDs3FeIntervalESs 1.3.6.1.4.1.18.3.4.13.7.1.3
the count of errored seconds in the specified interval
Status: mandatory Access: read-only
OBJECT-TYPE    
  Gauge  

wfDs3FeIntervalSESs 1.3.6.1.4.1.18.3.4.13.7.1.4
the count of severely errored seconds in the specified interval
Status: mandatory Access: read-only
OBJECT-TYPE    
  Gauge  

wfDs3FeIntervalCVs 1.3.6.1.4.1.18.3.4.13.7.1.5
the count of code violation error events in the specified interval
Status: mandatory Access: read-only
OBJECT-TYPE    
  Gauge  

wfDs3FeTotal 1.3.6.1.4.1.18.3.4.13.8
The DS3 Far End Total table
Status: mandatory Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    WfDs3FeTotalEntry

wfDs3FeTotalEntry 1.3.6.1.4.1.18.3.4.13.8.1
per circuit far end DS3 total objects - wfDs3FeTotalIndex corresponds to Wellfleet circuit number
Status: mandatory Access: not-accessible
OBJECT-TYPE    
  WfDs3FeTotalEntry  

wfDs3FeTotalIndex 1.3.6.1.4.1.18.3.4.13.8.1.1
this corresponds to the Wellfleet circuit number
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER minimum(1), maximum(1024)  

wfDs3FeTotalESs 1.3.6.1.4.1.18.3.4.13.8.1.2
total count of errored seconds
Status: mandatory Access: read-only
OBJECT-TYPE    
  Gauge  

wfDs3FeTotalSESs 1.3.6.1.4.1.18.3.4.13.8.1.3
total count of severely errored seconds
Status: mandatory Access: read-only
OBJECT-TYPE    
  Gauge  

wfDs3FeTotalCVs 1.3.6.1.4.1.18.3.4.13.8.1.4
total count of code violation error events
Status: mandatory Access: read-only
OBJECT-TYPE    
  Gauge  

wfE1Table 1.3.6.1.4.1.18.3.4.11
E1 line record
Status: mandatory Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    WfE1Entry

wfE1Entry 1.3.6.1.4.1.18.3.4.11.1
An entry in the E1 table
Status: mandatory Access: not-accessible
OBJECT-TYPE    
  WfE1Entry  

wfE1Delete 1.3.6.1.4.1.18.3.4.11.1.1
create/delete parameter, dflt = created
Status: mandatory Access: read-write
OBJECT-TYPE    
  INTEGER created(1), deleted(2)  

wfE1Disable 1.3.6.1.4.1.18.3.4.11.1.2
enable/disable parameter, dflt = enabled
Status: mandatory Access: read-write
OBJECT-TYPE    
  INTEGER enabled(1), disabled(2)  

wfE1State 1.3.6.1.4.1.18.3.4.11.1.3
line driver state variable, Not Present, Init, Up
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER up(1), init(3), notpresent(4)  

wfE1Slot 1.3.6.1.4.1.18.3.4.11.1.4
instance ID Slot, filled in by driver
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER minimum(1), maximum(14)  

wfE1Connector 1.3.6.1.4.1.18.3.4.11.1.5
instance ID Connector, filled in by driver
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER one(1), two(2)  

wfE1Madr 1.3.6.1.4.1.18.3.4.11.1.6
Line mac address, filled in by driver
Status: mandatory Access: read-only
OBJECT-TYPE    
  OCTET STRING  

wfE1HDB3Support 1.3.6.1.4.1.18.3.4.11.1.7
HDB3 Support - Enables or disables high density bipolar coding
Status: mandatory Access: read-write
OBJECT-TYPE    
  INTEGER enabled(1), disabled(2)  

wfE1ClockMode 1.3.6.1.4.1.18.3.4.11.1.8
Clock Mode - Specifies the source of the E1 transmit clock
Status: mandatory Access: read-write
OBJECT-TYPE    
  INTEGER internal(1), slave(2), manual(4), default(1)  

wfE1MiniDacs 1.3.6.1.4.1.18.3.4.11.1.9
MiniDacs Configuration - assigns each E1 channel to a specific function
Status: mandatory Access: read-write
OBJECT-TYPE    
  DisplayString  

wfE1BipolarVios 1.3.6.1.4.1.18.3.4.11.1.10
Number of Bipolar Violations
Status: mandatory Access: read-only
OBJECT-TYPE    
  Counter  

wfE1FrameErrs 1.3.6.1.4.1.18.3.4.11.1.11
Number of Frame errors
Status: mandatory Access: read-only
OBJECT-TYPE    
  Counter  

wfE1RcvRemAlms 1.3.6.1.4.1.18.3.4.11.1.12
Number of remote alarms received
Status: mandatory Access: read-only
OBJECT-TYPE    
  Counter  

wfE1RcvMfmAlms 1.3.6.1.4.1.18.3.4.11.1.13
Number of Multiframe Alarms Received
Status: mandatory Access: read-only
OBJECT-TYPE    
  Counter  

wfE1MfsErrs 1.3.6.1.4.1.18.3.4.11.1.14
Number of instances of CAS Multiframe resync criteria met
Status: mandatory Access: read-only
OBJECT-TYPE    
  Counter  

wfE1SyncLoss 1.3.6.1.4.1.18.3.4.11.1.15
Number of instances of sync loss
Status: mandatory Access: read-only
OBJECT-TYPE    
  Counter  

wfE1RcvSig1s 1.3.6.1.4.1.18.3.4.11.1.16
Number of instances of receive signalling all 1's
Status: mandatory Access: read-only
OBJECT-TYPE    
  Counter  

wfE1RcvUnfrm1s 1.3.6.1.4.1.18.3.4.11.1.17
Number of instances of Receive unframed all 1's
Status: mandatory Access: read-only
OBJECT-TYPE    
  Counter  

wfFakeEvent 1.3.6.1.4.1.18.3.5.3.5.4
OBJECT IDENTIFIER    

wfFakeEventString 1.3.6.1.4.1.18.3.5.3.5.4.1
A dummy display string. While no string will actually be kept here, the full identifier (object id + attribute id + instance ID ) will be used to wrap event strings passed from the system logger into an SNMP Trap message.
Status: optional Access: read-only
OBJECT-TYPE    
  DisplayString  

wfFddiTable 1.3.6.1.4.1.18.3.4.4
FDDI line record
Status: mandatory Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    WfFddiEntry

wfFddiEntry 1.3.6.1.4.1.18.3.4.4.1
An entry in the FDDI table
Status: mandatory Access: not-accessible
OBJECT-TYPE    
  WfFddiEntry  

wfFDDIDelete 1.3.6.1.4.1.18.3.4.4.1.1
create/delete parameter, default = created
Status: mandatory Access: read-write
OBJECT-TYPE    
  INTEGER create(1), delete(2)  

wfFDDIEnable 1.3.6.1.4.1.18.3.4.4.1.2
enable/disable parameter, default = enabled
Status: mandatory Access: read-write
OBJECT-TYPE    
  INTEGER enable(1), disable(2)  

wfFDDIState 1.3.6.1.4.1.18.3.4.4.1.3
line driver state variable, not present, init, down, up
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER up(1), down(2), init(3), notpresent(4)  

wfFDDISlot 1.3.6.1.4.1.18.3.4.4.1.4
instance ID slot - filled in by driver
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER minimum(1), maximum(14)  

wfFDDINode 1.3.6.1.4.1.18.3.4.4.1.5
instance ID Node - filled in by driver
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER one(1), two(2)  

wfFDDICct 1.3.6.1.4.1.18.3.4.4.1.6
cct number for this line instance
Status: mandatory Access: read-write
OBJECT-TYPE    
  INTEGER minimum(1), maximum(1023)  

wfFDDIBofl 1.3.6.1.4.1.18.3.4.4.1.7
bofl parameter, default = enabled
Status: mandatory Access: read-write
OBJECT-TYPE    
  INTEGER enable(1), disable(2)  

wfFDDIBoflTmo 1.3.6.1.4.1.18.3.4.4.1.8
bofl parameter, default = 5 seconds
Status: mandatory Access: read-write
OBJECT-TYPE    
  INTEGER minimum(1), maximum(60), default(5)  

wfFDDIMtu 1.3.6.1.4.1.18.3.4.4.1.9
mtu parameter, fixed
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER default(4495)  

wfFDDIMadr 1.3.6.1.4.1.18.3.4.4.1.10
line MAC address, fixed - line driver fills in
Status: mandatory Access: read-only
OBJECT-TYPE    
  OCTET STRING  

wfFDDIOctetsRxOk 1.3.6.1.4.1.18.3.4.4.1.11
Number of bytes received without error
Status: mandatory Access: read-only
OBJECT-TYPE    
  Counter  

wfFDDIFramesRxOk 1.3.6.1.4.1.18.3.4.4.1.12
Number of frames received without error
Status: mandatory Access: read-only
OBJECT-TYPE    
  Counter  

wfFDDIOctetsTxOk 1.3.6.1.4.1.18.3.4.4.1.13
Number of bytes transmitted without error
Status: mandatory Access: read-only
OBJECT-TYPE    
  Counter  

wfFDDIFramesTxOk 1.3.6.1.4.1.18.3.4.4.1.14
Number of frames transmitted without error
Status: mandatory Access: read-only
OBJECT-TYPE    
  Counter  

wfFDDICrcErrRx 1.3.6.1.4.1.18.3.4.4.1.15
Number of frames received with CRC errors
Status: mandatory Access: read-only
OBJECT-TYPE    
  Counter  

wfFDDIOverrunRx 1.3.6.1.4.1.18.3.4.4.1.16
Number of frames received with internal overrun errors
Status: mandatory Access: read-only
OBJECT-TYPE    
  Counter  

wfFDDIParityErrRx 1.3.6.1.4.1.18.3.4.4.1.17
Number of frames received with parity errors
Status: mandatory Access: read-only
OBJECT-TYPE    
  Counter  

wfFDDIMacErrRx 1.3.6.1.4.1.18.3.4.4.1.18
Number of frames received with mac errors
Status: mandatory Access: read-only
OBJECT-TYPE    
  Counter  

wfFDDIRingErrRx 1.3.6.1.4.1.18.3.4.4.1.19
Number of receive ring error events
Status: mandatory Access: read-only
OBJECT-TYPE    
  Counter  

wfFDDISmtRingErrRx 1.3.6.1.4.1.18.3.4.4.1.20
Number of SMT receive ring error events
Status: mandatory Access: read-only
OBJECT-TYPE    
  Counter  

wfFDDIRingOverrunRx 1.3.6.1.4.1.18.3.4.4.1.21
Number of LLC receive ring overrun events
Status: mandatory Access: read-only
OBJECT-TYPE    
  Counter  

wfFDDISmtRingOverrunRx 1.3.6.1.4.1.18.3.4.4.1.22
Number of SMT receive ring overrun events
Status: mandatory Access: read-only
OBJECT-TYPE    
  Counter  

wfFDDIAbortTx 1.3.6.1.4.1.18.3.4.4.1.23
Number of transmit frames with internal abort errors
Status: mandatory Access: read-only
OBJECT-TYPE    
  Counter  

wfFDDIUnderrunTx 1.3.6.1.4.1.18.3.4.4.1.24
Number of transmit frames aborted with underrun errors
Status: mandatory Access: read-only
OBJECT-TYPE    
  Counter  

wfFDDIParityErrTx 1.3.6.1.4.1.18.3.4.4.1.25
Number of transmit frames aborted with parity errors
Status: mandatory Access: read-only
OBJECT-TYPE    
  Counter  

wfFDDIRingErrTx 1.3.6.1.4.1.18.3.4.4.1.26
Number of LLC/SMT transmit ring error events
Status: mandatory Access: read-only
OBJECT-TYPE    
  Counter  

wfFDDIPortOpErr 1.3.6.1.4.1.18.3.4.4.1.27
Number of port operation error events
Status: mandatory Access: read-only
OBJECT-TYPE    
  Counter  

wfFDDIInternOpErr 1.3.6.1.4.1.18.3.4.4.1.28
Number of internal operation error events
Status: mandatory Access: read-only
OBJECT-TYPE    
  Counter  

wfFDDIHostErr 1.3.6.1.4.1.18.3.4.4.1.29
Number of host error events
Status: mandatory Access: read-only
OBJECT-TYPE    
  Counter  

wfFDDISmtConnectionPolicy 1.3.6.1.4.1.18.3.4.4.1.30
A value that indicates the connection policies enforced at the station. A station sets the corresponding policy for each of the connection types that it rejects. The letter designations, X and Y, in the 'rejectX-Y' names have the following significance: X represents the PC-Type of the local PORT and Y represents a PC-Neighbor in the evaluation of Connection-Policy (PC-Type, PC- Neighbor) that is done to determine the setting of T-Val(3) in the PC-Signaling sequence. The value is a sum. This value initially takes the value zero, then for each of the connection policies currently enforced on the node, 2 raised to a power is added to the sum. The powers are according to the following table: Policy Power rejectA-A 0 rejectA-B 1 rejectA-S 2 rejectA-M 3 rejectB-A 4 rejectB-B 5 rejectB-S 6 rejectB-M 7 rejectS-A 8 rejectS-B 9 rejectS-S 10 rejectS-M 11 rejectM-A 12 rejectM-B 13 rejectM-S 14 rejectM-M 15
Status: mandatory Access: read-write
OBJECT-TYPE    
  INTEGER default(65381)  

wfFDDISmtTNotify 1.3.6.1.4.1.18.3.4.4.1.31
The timer used in the Neighbor Notification protocol, reported in seconds and ranging from 2 to 30 seconds.
Status: mandatory Access: read-write
OBJECT-TYPE    
  INTEGER min(2), default(22), max(30)  

wfFDDIMacTReq 1.3.6.1.4.1.18.3.4.4.1.32
The requested Target Token Rotation Time (TTRT) for a MAC's synchronous traffic represented in unsigned integer specifying time in octet units (80 nanoseconds).
Status: mandatory Access: read-write
OBJECT-TYPE    
  INTEGER default(2062500)  

wfFDDIMacTMax 1.3.6.1.4.1.18.3.4.4.1.33
The requested maximum TTRT to be supported by a MAC represented in unsigned integer specifying time in octet units (80 nanoseconds).
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER default(2097152)  

wfFDDIMacTvxValue 1.3.6.1.4.1.18.3.4.4.1.34
The requested value of TvxValue represented in unsigned integer specifying time in octet units (80 nanoseconds).
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER default(32768)  

wfFDDIMacTMin 1.3.6.1.4.1.18.3.4.4.1.35
The requested minimum TTRT to be requested by a MAC represented in unsigned integer specifying time in octet units (80 nanoseconds).
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER default(50000)  

wfFDDIHardwareFilter 1.3.6.1.4.1.18.3.4.4.1.36
Hardware filter (CAM) parameter.
Status: mandatory Access: read-write
OBJECT-TYPE    
  INTEGER enable(1), disable(2)  

wfFDDISmtEnable 1.3.6.1.4.1.18.3.4.4.1.37
Status: mandatory Access: read-write
OBJECT-TYPE    
  INTEGER enable(1), disable(2)  

wfFDDITxQueueLength 1.3.6.1.4.1.18.3.4.4.1.38
Transmit Queue Length, values larger than the compiled ring size are truncated to the compiled ring size.
Status: mandatory Access: read-write
OBJECT-TYPE    
  INTEGER minimum(1), maximum(255), default(127)  

wfFDDIRxQueueLength 1.3.6.1.4.1.18.3.4.4.1.39
Receive Queue Length, values larger than the compiled ring size are truncated to the compiled ring size.
Status: mandatory Access: read-write
OBJECT-TYPE    
  INTEGER minimum(1), maximum(255), default(64)  

wfFDDITxClipFrames 1.3.6.1.4.1.18.3.4.4.1.40
Number of frames clipped in driver's transmit routine due to transmit congestion.
Status: mandatory Access: read-only
OBJECT-TYPE    
  Counter  

wfFDDIRxReplenMisses 1.3.6.1.4.1.18.3.4.4.1.41
Number of packet buffer misses while attempting to replenish driver receive ring.
Status: mandatory Access: read-only
OBJECT-TYPE    
  Counter  

wfFddiSmtTable 1.3.6.1.4.1.18.3.4.15.1.2
A list of SMT entries.
Status: mandatory Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    WfFddiSmtEntry

wfFddiSmtEntry 1.3.6.1.4.1.18.3.4.15.1.2.1
An SMT entry containing information common to a given SMT.
Status: mandatory Access: not-accessible
OBJECT-TYPE    
  WfFddiSmtEntry  

wfFddiSmtSlot 1.3.6.1.4.1.18.3.4.15.1.2.1.1
Slot number associated with an SMT entity.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER  

wfFddiSmtNode 1.3.6.1.4.1.18.3.4.15.1.2.1.2
Node/connector number associated with an SMT entity.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER  

wfFddiSmtCct 1.3.6.1.4.1.18.3.4.15.1.2.1.3
Circuit number associated with an SMT entity.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER  

wfFddiSmtStationId 1.3.6.1.4.1.18.3.4.15.1.2.1.4
Unique identifier of an FDDI station.
Status: mandatory Access: read-only
OBJECT-TYPE    
  OCTET STRING  

wfFddiSmtOpVersionId 1.3.6.1.4.1.18.3.4.15.1.2.1.5
The version that this station is using for its operation.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER  

wfFddiSmtMacCt 1.3.6.1.4.1.18.3.4.15.1.2.1.6
The number of MACs in the station or concentrator.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER  

wfFddiSmtNonMasterCt 1.3.6.1.4.1.18.3.4.15.1.2.1.7
The number of Non Master PORTs (A, B, or S PORTs) in the station or concentrator.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER  

wfFddiSmtEcmState 1.3.6.1.4.1.18.3.4.15.1.2.1.8
Indicates the current state of the ECM state machine.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER out(1), in(2), trace(3), leave(4), pathtest(5), insert(6), check(7), deinsert(8)  

wfFddiSmtCfState 1.3.6.1.4.1.18.3.4.15.1.2.1.9
The attachment configuration for the station or concentrator.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER isolated(1), wraps(2), wrapa(3), wrapb(4), wrapab(5), thru(6)  

wfFddiMacTable 1.3.6.1.4.1.18.3.4.15.2.2
A list of MAC entries.
Status: mandatory Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    WfFddiMacEntry

wfFddiMacEntry 1.3.6.1.4.1.18.3.4.15.2.2.1
A MAC entry containing information common to a given MAC.
Status: mandatory Access: not-accessible
OBJECT-TYPE    
  WfFddiMacEntry  

wfFddiMacSlot 1.3.6.1.4.1.18.3.4.15.2.2.1.1
Slot number associated with a MAC entity.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER  

wfFddiMacNode 1.3.6.1.4.1.18.3.4.15.2.2.1.2
Node/connector number associated with a MAC entity.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER  

wfFddiMacCct 1.3.6.1.4.1.18.3.4.15.2.2.1.3
Circuit number associated with a MAC entity.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER  

wfFddiMacUpstreamNbr 1.3.6.1.4.1.18.3.4.15.2.2.1.4
The MAC's upstream neighbor's long individual MAC address. It may be determined by the Neighbor Information Frame protocol. The value shall be reported as '00 00 00 00 00 00' if it is unknown.
Status: mandatory Access: read-only
OBJECT-TYPE    
  OCTET STRING  

wfFddiMacDownstreamNbr 1.3.6.1.4.1.18.3.4.15.2.2.1.5
The MAC's downstream neighbor's long individual MAC address. It may be determined by the Neighbor Information Frame protocol. The value shall be reported as '00 00 00 00 00 00' if it is unknown.
Status: mandatory Access: read-only
OBJECT-TYPE    
  OCTET STRING  

wfFddiMacSmtAddress 1.3.6.1.4.1.18.3.4.15.2.2.1.6
The 48 bit individual address of the MAC used for SMT frames.
Status: mandatory Access: read-only
OBJECT-TYPE    
  OCTET STRING  

wfFddiMacTNeg 1.3.6.1.4.1.18.3.4.15.2.2.1.7
The negotiated TTRT during the claim process represented in unsigned integer specifying time in octet units (80 nanosecond).
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER  

wfFddiMacRmtState 1.3.6.1.4.1.18.3.4.15.2.2.1.8
Indicates the current state of the Ring Management state machine.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER isolated(1), nonop(2), ringop(4), detect(8), nonopdup(16), ringopdup(32), directed(64), trace(128)  

wfFddiPortTable 1.3.6.1.4.1.18.3.4.15.4.2
A list of PORT entries. The number of entries is given by the value of wfFddiPortNumber.
Status: mandatory Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    WfFddiPortEntry

wfFddiPortEntry 1.3.6.1.4.1.18.3.4.15.4.2.1
A PORT entry containing information common to a given PORT.
Status: mandatory Access: not-accessible
OBJECT-TYPE    
  WfFddiPortEntry  

wfFddiPortSlot 1.3.6.1.4.1.18.3.4.15.4.2.1.1
Slot number associated with a PORT entity.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER  

wfFddiPortNode 1.3.6.1.4.1.18.3.4.15.4.2.1.2
Node/connector number associated with a PORT entity.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER  

wfFddiPortCct 1.3.6.1.4.1.18.3.4.15.4.2.1.3
Circuit number associated with a PORT entity.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER  

wfFddiPortIndex 1.3.6.1.4.1.18.3.4.15.4.2.1.4
A unique value for each PORT associated with each slot/connector pair.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER  

wfFddiPortPcType 1.3.6.1.4.1.18.3.4.15.4.2.1.5
PC_Type.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER a(1), b(2), s(3), m(4)  

wfFddiPortPcNeighbor 1.3.6.1.4.1.18.3.4.15.4.2.1.6
The type (PC_Neighbor) of the remote PORT that is determined in PC_Signaling in R_Val (1,2).
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER a(1), b(2), s(3), m(4), unknown(5)  

wfFddiPortPcmState 1.3.6.1.4.1.18.3.4.15.4.2.1.7
State of Physical State Machine.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER off(1), break(2), trace(3), connect(4), next(5), signal(6), join(7), verify(8), active(9), maint(10)  

wfFrDlcmiTable 1.3.6.1.4.1.18.3.5.9.1.1
The Parameters for the Data Link Connection Management Interface
Status: mandatory Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    WfFrDlcmiEntry

wfFrDlcmiEntry 1.3.6.1.4.1.18.3.5.9.1.1.1
The parameters for a particular Data Link Connection Management Interface
Status: mandatory Access: not-accessible
OBJECT-TYPE    
  WfFrDlcmiEntry  

wfFrDlcmiDelete 1.3.6.1.4.1.18.3.5.9.1.1.1.1
Indication to delete this frame relay interface
Status: mandatory Access: read-write
OBJECT-TYPE    
  INTEGER created(1), deleted(2)  

wfFrDlcmiDisable 1.3.6.1.4.1.18.3.5.9.1.1.1.2
Indicates when a dlcmi entry is to be enabled or disabled.
Status: mandatory Access: read-write
OBJECT-TYPE    
  INTEGER enabled(1), disabled(2)  

wfFrDlcmiState 1.3.6.1.4.1.18.3.5.9.1.1.1.3
The current state of Frame Relay. The not present state is not actually valid except when the record is first added. It is included for consistency.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER up(1), down(2), init(3), notpresent(4)  

wfFrDlcmiCircuit 1.3.6.1.4.1.18.3.5.9.1.1.1.4
Instance identifier. The circuit number of this entry
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER  

wfFrDlcmiManagementType 1.3.6.1.4.1.18.3.5.9.1.1.1.5
This variable indicates which Data Link Connection Management scheme is active (and by implication, what DLCI it uses).
Status: mandatory Access: read-write
OBJECT-TYPE    
  INTEGER none(1), lmi(2), t1617d(3), t1617b(4), annexa(5), lmiswitch(6), annexdswitch(7), annexaswitch(8)  

wfFrDlcmiStatus 1.3.6.1.4.1.18.3.5.9.1.1.1.6
Indicates the status of the interface. FR_STATUS_START is the state during rebooting or initial start of circuit FR_STATUS_RUNNING is the sate after the circuit is up (either LMI successful or there is no DLCMI and the system just comes up). FR_STATUS_FAULT is a transient state indicating that errors have caused the circuit to be disabled until DLCMI recovery. FR_STATUS_RECOVERED indicates that an the system has been in the FR_STATUS_FAULT mode before, but has since recovered.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER start(1), running(2), fault(3), recovered(4)  

wfFrDlcmiAddress 1.3.6.1.4.1.18.3.5.9.1.1.1.7
This states which address format is in use on the FR interface. The default is Q922
Status: mandatory Access: read-write
OBJECT-TYPE    
  INTEGER q921(1), q922march90(2), q922november90(3), q922(4)  

wfFrDlcmiAddressLen 1.3.6.1.4.1.18.3.5.9.1.1.1.8
This variable states the address length in octets. In the case of Q922 format, the length indicates the entire length of the address includeding the control portion.
Status: mandatory Access: read-write
OBJECT-TYPE    
  INTEGER twobyte(2), threebyte(3), fourbyte(4)  

wfFrDlcmiPollingInterval 1.3.6.1.4.1.18.3.5.9.1.1.1.9
The number of seconds between successive status enquiry messages
Status: mandatory Access: read-write
OBJECT-TYPE    
  INTEGER minimum(5), default(10), maximum(30)  

wfFrDlcmiFullEnquiryInterval 1.3.6.1.4.1.18.3.5.9.1.1.1.10
The number of status enquiry intervals that pass before issuance of a full status enquiry message.
Status: mandatory Access: read-write
OBJECT-TYPE    
  INTEGER minimum(1), default(6), maximum(255)  

wfFrDlcmiErrorThreshold 1.3.6.1.4.1.18.3.5.9.1.1.1.11
This is the maximum number of unanswered Status Enquiries the equipment shall accept before declaring the interface down.
Status: mandatory Access: read-write
OBJECT-TYPE    
  INTEGER  

wfFrDlcmiMonitoredEvents 1.3.6.1.4.1.18.3.5.9.1.1.1.12
This is the number of status polling intervals over which the error threshold is counted. For example, if within 'MonitoredEvents' number of events the station receives 'ErrorThreshold' number of errors, the interface is marked as down.
Status: mandatory Access: read-write
OBJECT-TYPE    
  INTEGER  

wfFrDlcmiMaxSupportedVCs 1.3.6.1.4.1.18.3.5.9.1.1.1.13
The maximum number of Virtual Circuits allowed for this interface. Usually dictated by the Frame Relay network. The system sets this initially.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER  

wfFrDlcmiMulticast 1.3.6.1.4.1.18.3.5.9.1.1.1.14
This indicates whether the frame relay provider offers a multicast
Status: mandatory Access: read-write
OBJECT-TYPE    
  INTEGER enabled(1), disabled(2)  

wfFrDlcmiSeqCount 1.3.6.1.4.1.18.3.5.9.1.1.1.15
This station's sequence counter. It represents the next value to send.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER minimum(1), maximum(255)  

wfFrDlcmiLastReceived 1.3.6.1.4.1.18.3.5.9.1.1.1.16
The sequence number just received from the switch.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER minimum(1), maximum(255)  

wfFrDlcmiPassiveSeqCount 1.3.6.1.4.1.18.3.5.9.1.1.1.17
This station's sequence counter for answering status enquiry.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER minimum(1), maximum(255)  

wfFrDlcmiPassiveReceived 1.3.6.1.4.1.18.3.5.9.1.1.1.18
The sequence number just received from the enquring station.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER minimum(1), maximum(255)  

wfFrDlcmiPolls 1.3.6.1.4.1.18.3.5.9.1.1.1.19
This is the counter of where we are in the polling cycle.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER  

wfFrDlcmiAlarmTimer 1.3.6.1.4.1.18.3.5.9.1.1.1.20
This is a counter of 1/2 second timeouts. When it reaches 2 x the polling interval, an enquiry message is sent.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER  

wfFrErrType 1.3.6.1.4.1.18.3.5.9.1.1.1.21
Indicate the type of the last specific monitored error.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER unknown(1), short(2), long(3), illegaldlci(4), unknowndlci(5), protoerr(6), unknownie(7), sequenceerr(8), unknownrpt(9), reset(10), cntrl(11)  

wfFrErrData 1.3.6.1.4.1.18.3.5.9.1.1.1.22
Contains as much of the error packet as possible.
Status: mandatory Access: read-only
OBJECT-TYPE    
  OCTET STRING  

wfFrErrTime 1.3.6.1.4.1.18.3.5.9.1.1.1.23
The time the last error occurred.
Status: mandatory Access: read-only
OBJECT-TYPE    
  TimeTicks  

wfFrErrDiscards 1.3.6.1.4.1.18.3.5.9.1.1.1.24
The number of inbound frames dropped because of format or other errors or because the VC was not known.
Status: mandatory Access: read-only
OBJECT-TYPE    
  Counter  

wfFrErrDrops 1.3.6.1.4.1.18.3.5.9.1.1.1.25
The number of outbound frames dropped. Usually this is due the specified DLCI being unknown or a broadcast packet is too long
Status: mandatory Access: read-only
OBJECT-TYPE    
  Counter  

wfFrCircuitTable 1.3.6.1.4.1.18.3.5.9.1.2
Frame Relay Circuit table gives information about a virtual circuits.
Status: mandatory Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    WfFrCircuitEntry

wfFrCircuitEntry 1.3.6.1.4.1.18.3.5.9.1.2.1
An entry in the Frame Relay Circuit table.
Status: mandatory Access: not-accessible
OBJECT-TYPE    
  WfFrCircuitEntry  

wfFrCircuitDelete 1.3.6.1.4.1.18.3.5.9.1.2.1.1
Indication to delete this frame relay interface.
Status: mandatory Access: read-write
OBJECT-TYPE    
  INTEGER created(1), deleted(2), system(3)  

wfFrCircuitNumber 1.3.6.1.4.1.18.3.5.9.1.2.1.2
Instance identifier. The circuit number of this interface.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER  

wfFrCircuitDlci 1.3.6.1.4.1.18.3.5.9.1.2.1.3
Instance identifier. This indicates which virtual circuit.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER twobyteminimum(16), twobytemaximum(1007), threebyteminimum(1024), threebytemaximum(64511), fourbyteminimum(131072), fourbytemaximum(8257535)  

wfFrCircuitState 1.3.6.1.4.1.18.3.5.9.1.2.1.4
Indicates the state of the particular virtual circuit.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER invalid(1), active(2), inactive(3), xoff(4), control(5)  

wfFrCircuitStateSet 1.3.6.1.4.1.18.3.5.9.1.2.1.5
User access for setting the state of a virtual circuit
Status: mandatory Access: read-write
OBJECT-TYPE    
  INTEGER invalid(1), active(2), inactive(3)  

wfFrCircuitReceivedFECNs 1.3.6.1.4.1.18.3.5.9.1.2.1.6
Number of frames received indicating forward congestion.
Status: mandatory Access: read-only
OBJECT-TYPE    
  Counter  

wfFrCircuitReceivedBECNs 1.3.6.1.4.1.18.3.5.9.1.2.1.7
Number of frames received indicating backward congestion.
Status: mandatory Access: read-only
OBJECT-TYPE    
  Counter  

wfFrCircuitSentFrames 1.3.6.1.4.1.18.3.5.9.1.2.1.8
The number of frames sent from this virtual circuit.
Status: mandatory Access: read-only
OBJECT-TYPE    
  Counter  

wfFrCircuitSentOctets 1.3.6.1.4.1.18.3.5.9.1.2.1.9
The number of octets sent from this virtual circuit.
Status: mandatory Access: read-only
OBJECT-TYPE    
  Counter  

wfFrCircuitReceivedFrames 1.3.6.1.4.1.18.3.5.9.1.2.1.10
The number of frames received from this virtual circuit.
Status: mandatory Access: read-only
OBJECT-TYPE    
  Counter  

wfFrCircuitReceivedOctets 1.3.6.1.4.1.18.3.5.9.1.2.1.11
The number of octets received from this virtual circuit.
Status: mandatory Access: read-only
OBJECT-TYPE    
  Counter  

wfFrCircuitCreationTime 1.3.6.1.4.1.18.3.5.9.1.2.1.12
The value of sysUpTime when the vc was created.
Status: mandatory Access: read-only
OBJECT-TYPE    
  TimeTicks  

wfFrCircuitLastTimeChange 1.3.6.1.4.1.18.3.5.9.1.2.1.13
The value of sysUpTime when last there was a change in vc state.
Status: mandatory Access: read-only
OBJECT-TYPE    
  TimeTicks  

wfFrCircuitCommittedBurst 1.3.6.1.4.1.18.3.5.9.1.2.1.14
Indicates the maximum amount of data, in bits, that the network agrees to transfer under normal conditions, during the measurement interval. Wellfleet does not presently support this.
Status: mandatory Access: read-write
OBJECT-TYPE    
  INTEGER  

wfFrCircuitExcessBurst 1.3.6.1.4.1.18.3.5.9.1.2.1.15
Indicates teh maximum amount of uncommitted data bits that the network will attempt to deliver over the measurement interval. Wellfleet does not presently support this.
Status: mandatory Access: read-write
OBJECT-TYPE    
  INTEGER  

wfFrCircuitThroughput 1.3.6.1.4.1.18.3.5.9.1.2.1.16
This is the average number of 'Frame Relay Information Field' bits transferred per second across a user network interface in one direction, measured over the measurement interval. Wellfleet does not presently support this.
Status: mandatory Access: read-write
OBJECT-TYPE    
  INTEGER  

wfFrCircuitMulticast 1.3.6.1.4.1.18.3.5.9.1.2.1.17
Indicates whether this DLCI is used for multicast or single destination.
Status: mandatory Access: read-write
OBJECT-TYPE    
  INTEGER multicast(1), unicast(2)  

wfFrCircuitDiscards 1.3.6.1.4.1.18.3.5.9.1.2.1.18
The number of inbound frames discarded because of format errors, because the VC is inactive or because the protocol was not registered for this circuit.
Status: mandatory Access: read-only
OBJECT-TYPE    
  Counter  

wfFrCircuitDrops 1.3.6.1.4.1.18.3.5.9.1.2.1.19
Indicates how many outbound frames were dropped. Usually these are dropped because the VC is not active.
Status: mandatory Access: read-only
OBJECT-TYPE    
  Counter  

wfFrCircuitSubCct 1.3.6.1.4.1.18.3.5.9.1.2.1.20
Circuit number to use for this VC when configured in hybrid (for bridging) or direct access (VC as a circuit) mode.
Status: mandatory Access: read-write
OBJECT-TYPE    
  INTEGER  

wfFrCircuitMode 1.3.6.1.4.1.18.3.5.9.1.2.1.21
The mode of the given VC. GROUP - treats the VC as one of many vc's on a circuit. HYBRID - treats the VC as one of many vc's on a circuit for protocol traffic, but as a separate circuit for bridging. DIRECT - treats the VC as a separate circuit for all applications.
Status: mandatory Access: read-write
OBJECT-TYPE    
  INTEGER group(1), hybrid(2), direct(3)  

wfKernelTable 1.3.6.1.4.1.18.3.3.2.5.1
Table of kernel statistics, indexed by slot number
Status: mandatory Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    WfKernelEntry

wfKernelEntry 1.3.6.1.4.1.18.3.3.2.5.1.1
A particular interface
Status: mandatory Access: not-accessible
OBJECT-TYPE    
  WfKernelEntry  

wfKernelSlot 1.3.6.1.4.1.18.3.3.2.5.1.1.1
The slot number indexes the kernel statistics table
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER  

wfKernelMemorySize 1.3.6.1.4.1.18.3.3.2.5.1.1.2
The total size of allocatable memory, in bytes
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER  

wfKernelMemoryFree 1.3.6.1.4.1.18.3.3.2.5.1.1.3
The amount of memory which hasn't been allocated yet, in bytes
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER  

wfKernelMemorySegsTotal 1.3.6.1.4.1.18.3.3.2.5.1.1.4
Total number of memory segments in the kernel
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER  

wfKernelMemorySegsFree 1.3.6.1.4.1.18.3.3.2.5.1.1.5
Total number of unallocated memory segments in the kernel
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER  

wfKernelMemoryMaxSegFree 1.3.6.1.4.1.18.3.3.2.5.1.1.6
Size of the largest unallocated memory segment
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER  

wfKernelBuffersTotal 1.3.6.1.4.1.18.3.3.2.5.1.1.7
Total number of packet buffers
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER  

wfKernelBuffersFree 1.3.6.1.4.1.18.3.3.2.5.1.1.8
Number of packet buffers in the free pool
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER  

wfKernelTasksTotal 1.3.6.1.4.1.18.3.3.2.5.1.1.9
Number of tasks running
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER  

wfKernelTasksInQueue 1.3.6.1.4.1.18.3.3.2.5.1.1.10
Number of tasks awaiting scheduling
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER  

wfKernelTimersTotal 1.3.6.1.4.1.18.3.3.2.5.1.1.11
Total number of timers available
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER  

wfKernelTimersActive 1.3.6.1.4.1.18.3.3.2.5.1.1.12
Total number of timers in use by tasks
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER  

wfKernelBufOwnerTask1 1.3.6.1.4.1.18.3.3.2.5.1.1.13
Activation address of task which owns many buffers
Status: mandatory Access: read-only
OBJECT-TYPE    
  DisplayString  

wfKernelBufOwnerTask1Bufs 1.3.6.1.4.1.18.3.3.2.5.1.1.14
Number of buffers owned by the task
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER  

wfKernelBufOwnerTask2 1.3.6.1.4.1.18.3.3.2.5.1.1.15
Activation address of task which owns many buffers
Status: mandatory Access: read-only
OBJECT-TYPE    
  DisplayString  

wfKernelBufOwnerTask2Bufs 1.3.6.1.4.1.18.3.3.2.5.1.1.16
Number of buffers owned by the task
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER  

wfKernelBufOwnerTask3 1.3.6.1.4.1.18.3.3.2.5.1.1.17
Activation address of task which owns many buffers
Status: mandatory Access: read-only
OBJECT-TYPE    
  DisplayString  

wfKernelBufOwnerTask3Bufs 1.3.6.1.4.1.18.3.3.2.5.1.1.18
Number of buffers owned by the task
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER  

wfKernelBufOwnerTask4 1.3.6.1.4.1.18.3.3.2.5.1.1.19
Activation address of task which owns many buffers
Status: mandatory Access: read-only
OBJECT-TYPE    
  DisplayString  

wfKernelBufOwnerTask4Bufs 1.3.6.1.4.1.18.3.3.2.5.1.1.20
Number of buffers owned by the task
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER  

wfKernelBufOwnerTask5 1.3.6.1.4.1.18.3.3.2.5.1.1.21
Activation address of task which owns many buffers
Status: mandatory Access: read-only
OBJECT-TYPE    
  DisplayString  

wfKernelBufOwnerTask5Bufs 1.3.6.1.4.1.18.3.3.2.5.1.1.22
Number of buffers owned by the task
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER  

wfKernelBufOwnerTask6 1.3.6.1.4.1.18.3.3.2.5.1.1.23
Activation address of task which owns many buffers
Status: mandatory Access: read-only
OBJECT-TYPE    
  DisplayString  

wfKernelBufOwnerTask6Bufs 1.3.6.1.4.1.18.3.3.2.5.1.1.24
Number of buffers owned by the task
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER  

wfKernelBufOwnerTask7 1.3.6.1.4.1.18.3.3.2.5.1.1.25
Activation address of task which owns many buffers
Status: mandatory Access: read-only
OBJECT-TYPE    
  DisplayString  

wfKernelBufOwnerTask7Bufs 1.3.6.1.4.1.18.3.3.2.5.1.1.26
Number of buffers owned by the task
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER  

wfKernelBufOwnerTask8 1.3.6.1.4.1.18.3.3.2.5.1.1.27
Activation address of task which owns many buffers
Status: mandatory Access: read-only
OBJECT-TYPE    
  DisplayString  

wfKernelBufOwnerTask8Bufs 1.3.6.1.4.1.18.3.3.2.5.1.1.28
Number of buffers owned by the task
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER  

wfKernelBufOwnerTask9 1.3.6.1.4.1.18.3.3.2.5.1.1.29
Activation address of task which owns many buffers
Status: mandatory Access: read-only
OBJECT-TYPE    
  DisplayString  

wfKernelBufOwnerTask9Bufs 1.3.6.1.4.1.18.3.3.2.5.1.1.30
Number of buffers owned by the task
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER  

wfKernelBufOwnerTask10 1.3.6.1.4.1.18.3.3.2.5.1.1.31
Activation address of task which owns many buffers
Status: mandatory Access: read-only
OBJECT-TYPE    
  DisplayString  

wfKernelBufOwnerTask10Bufs 1.3.6.1.4.1.18.3.3.2.5.1.1.32
Number of buffers owned by the task
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER  

wfKernelMemOwnerTask1 1.3.6.1.4.1.18.3.3.2.5.1.1.33
Activation address of task which owns a sizable amount of memory
Status: mandatory Access: read-only
OBJECT-TYPE    
  DisplayString  

wfKernelMemOwnerTask1Size 1.3.6.1.4.1.18.3.3.2.5.1.1.34
Amount of memory owned by the task
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER  

wfKernelMemOwnerTask2 1.3.6.1.4.1.18.3.3.2.5.1.1.35
Activation address of task which owns a sizable amount of memory
Status: mandatory Access: read-only
OBJECT-TYPE    
  DisplayString  

wfKernelMemOwnerTask2Size 1.3.6.1.4.1.18.3.3.2.5.1.1.36
Amount of memory owned by the task
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER  

wfKernelMemOwnerTask3 1.3.6.1.4.1.18.3.3.2.5.1.1.37
Activation address of task which owns a sizable amount of memory
Status: mandatory Access: read-only
OBJECT-TYPE    
  DisplayString  

wfKernelMemOwnerTask3Size 1.3.6.1.4.1.18.3.3.2.5.1.1.38
Amount of memory owned by the task
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER  

wfKernelMemOwnerTask4 1.3.6.1.4.1.18.3.3.2.5.1.1.39
Activation address of task which owns a sizable amount of memory
Status: mandatory Access: read-only
OBJECT-TYPE    
  DisplayString  

wfKernelMemOwnerTask4Size 1.3.6.1.4.1.18.3.3.2.5.1.1.40
Amount of memory owned by the task
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER  

wfKernelMemOwnerTask5 1.3.6.1.4.1.18.3.3.2.5.1.1.41
Activation address of task which owns a sizable amount of memory
Status: mandatory Access: read-only
OBJECT-TYPE    
  DisplayString  

wfKernelMemOwnerTask5Size 1.3.6.1.4.1.18.3.3.2.5.1.1.42
Amount of memory owned by the task
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER  

wfKernelMemOwnerTask6 1.3.6.1.4.1.18.3.3.2.5.1.1.43
Activation address of task which owns a sizable amount of memory
Status: mandatory Access: read-only
OBJECT-TYPE    
  DisplayString  

wfKernelMemOwnerTask6Size 1.3.6.1.4.1.18.3.3.2.5.1.1.44
Amount of memory owned by the task
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER  

wfKernelMemOwnerTask7 1.3.6.1.4.1.18.3.3.2.5.1.1.45
Activation address of task which owns a sizable amount of memory
Status: mandatory Access: read-only
OBJECT-TYPE    
  DisplayString  

wfKernelMemOwnerTask7Size 1.3.6.1.4.1.18.3.3.2.5.1.1.46
Amount of memory owned by the task
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER  

wfKernelMemOwnerTask8 1.3.6.1.4.1.18.3.3.2.5.1.1.47
Activation address of task which owns a sizable amount of memory
Status: mandatory Access: read-only
OBJECT-TYPE    
  DisplayString  

wfKernelMemOwnerTask8Size 1.3.6.1.4.1.18.3.3.2.5.1.1.48
Amount of memory owned by the task
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER  

wfKernelMemOwnerTask9 1.3.6.1.4.1.18.3.3.2.5.1.1.49
Activation address of task which owns a sizable amount of memory
Status: mandatory Access: read-only
OBJECT-TYPE    
  DisplayString  

wfKernelMemOwnerTask9Size 1.3.6.1.4.1.18.3.3.2.5.1.1.50
Amount of memory owned by the task
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER  

wfKernelMemOwnerTask10 1.3.6.1.4.1.18.3.3.2.5.1.1.51
Activation address of task which owns a sizable amount of memory
Status: mandatory Access: read-only
OBJECT-TYPE    
  DisplayString  

wfKernelMemOwnerTask10Size 1.3.6.1.4.1.18.3.3.2.5.1.1.52
Amount of memory owned by the task
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER  

wfHwBase 1.3.6.1.4.1.18.3.1.1
OBJECT IDENTIFIER    

wfHwBpIdOpt 1.3.6.1.4.1.18.3.1.1.1
The BackPlane identification number.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER acefn(1), aceln(2), acecn(3), fns(4), in(5), freln(16640), frecn(16896)  

wfHwBpRev 1.3.6.1.4.1.18.3.1.1.2
The revision level of the BackPlane. High byte is in upper 2 bytes.
Status: mandatory Access: read-only
OBJECT-TYPE    
  OCTET STRING  

wfHwBpSerialNumber 1.3.6.1.4.1.18.3.1.1.3
The serial number of the BackPlane.
Status: mandatory Access: read-only
OBJECT-TYPE    
  OCTET STRING  

wfBCNPwrSupply1 1.3.6.1.4.1.18.3.1.1.4
Status of BCN Hot-Swappable Power Supply 1
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER ok(1), fail(2), notpresent(3)  

wfBCNPwrSupply2 1.3.6.1.4.1.18.3.1.1.5
Status of BCN Hot-Swappable Power Supply 2
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER ok(1), fail(2), notpresent(3)  

wfBCNPwrSupply3 1.3.6.1.4.1.18.3.1.1.6
Status of BCN Hot-Swappable Power Supply 3
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER ok(1), fail(2), notpresent(3)  

wfBCNPwrSupply4 1.3.6.1.4.1.18.3.1.1.7
Status of BCN Hot-Swappable Power Supply 4
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER ok(1), fail(2), notpresent(3)  

wfBCNFanStatus 1.3.6.1.4.1.18.3.1.1.8
Status of BCN Fan Tray
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER ok(1), fail(2), notpresent(3)  

wfBCNTemperature 1.3.6.1.4.1.18.3.1.1.9
Status of BCN Fan Tray
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER ok(1), caution(2), notpresent(3)  

wfHwTable 1.3.6.1.4.1.18.3.1.2
Hardware Table - indexed by slot number
Status: mandatory Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    WfHwEntry

wfHwEntry 1.3.6.1.4.1.18.3.1.2.1
Hardware specific information about a slot.
Status: mandatory Access: not-accessible
OBJECT-TYPE    
  WfHwEntry  

wfHwSlot 1.3.6.1.4.1.18.3.1.2.1.1
A unique value for each slot. Its value ranges between 1 and 14. There are products in this family that contain 1, 5, and 14 slots.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER  

wfHwModIdOpt 1.3.6.1.4.1.18.3.1.2.1.2
The module identification number. Port Configurations HWStat Name Enet Sync Async Token Framer Fiber ------ ------------ ------ ---- ----- ----- ------ ----- 1 ENET-1 2 0 0 0 0 0 8 ENET-2 2 0 0 0 0 0 16 SYNC-1 0 4 1 0 0 0 17 SYNC-1 [1] 0 4 1 0 0 0 24 T1-1 0 2 1 0 2 0 32 DSE-1 1 2 1 0 0 0 33 DSE-1 [1] 1 2 1 0 0 0 40 DST-4/16 0 2 1 1 0 0 41 SST-4/16 [1] 0 1 1 1 0 0 42 DST-4 0 2 1 1 0 0 43 SST-4 [1] 0 1 1 1 0 0 44 SST-4/16 0 1 1 1 0 0 45 STOK-4/16 [3] 0 0 0 1 0 0 46 SST-4 0 1 1 1 0 0 47 STOK-4 [3] 0 0 0 1 0 0 48 FLOPPY 0 0 0 0 0 0 56 T1-2 0 2 1 0 2 0 57 T1-2 0 2 1 0 2 0 58 ST1 0 1 1 0 1 0 60 T1-56K 0 1 1 0 1 0 61 E1 [3] 0 2 0 0 2 0 62 ST1-56K 0 1 1 0 1 0 63 SE1 [3] 0 1 0 0 1 0 64 T1-2n 0 2 1 0 2 0 65 ST1n 0 1 1 0 1 0 66 T1-56Kn 0 1 1 0 1 0 67 ST1-56Kn 0 1 1 0 1 0 68 E1n [3] 0 2 0 0 2 0 69 SE1n [3] 0 1 0 0 1 0 80 SYNC-2 0 4 1 0 0 0 81 SYNC-2 [1] 0 4 1 0 0 0 88 CMC-FDDI [6] 0 0 0 0 0 1 89 IPHASE-FDDI [6] 0 0 0 0 0 1 104 DT 0 0 0 2 0 0 112 DSDE-1 2 2 1 0 0 0 113 DSDE-1 [1] 2 2 1 0 0 0 114 ENET 2 0 0 0 0 0 116 DSE-2 1 2 1 0 0 0 117 DSE-2 [1] 1 2 1 0 0 0 118 SSE 1 1 1 0 0 0 119 SSE [1] 1 1 1 0 0 0 120 DSDE10BT 2 2 0 0 0 0 132 ENET-3 [2] 2 0 0 0 0 0 156 DSDE-2 [2] 2 2 1 0 0 0 160 QE/NF 4 0 0 0 0 0 161 DE/NF [5] 2 0 0 0 0 0 162 QE/NF 4 0 0 0 0 0 164 QE/F [4] 4 0 0 0 0 0 165 DE/F [4,5] 2 0 0 0 0 0 168 MCT1 0 2 Munich 0 0 2 0 176 DTOK 0 0 0 2 0 0 168 MCE1 0 2 Munich 0 0 2 0 192 WF_FDDI_2M 0 0 0 0 0 1 193 WF_FDDI_1M 0 0 0 0 0 1 194 WF_FDDI_2S 0 0 0 0 0 1 195 WF_FDDI_1S 0 0 0 0 0 1 196 WF_FDDI_2MF 0 0 0 0 0 1 197 WF_FDDI_1MF 0 0 0 0 0 1 198 WF_FDDI_2SF 0 0 0 0 0 1 199 WF_FDDI_1SF 0 0 0 0 0 1 208 FNSDSE [7] 1 2 0 0 0 0 216 FNSDSDT [7] 0 2 0 2 0 0 217 FNSDST [7] 0 2 0 1 0 0 224 DHSSI 0 2 hssi 0 0 0 0 225 SHSSI 0 1 hssi 0 0 0 0 8448 SRML 0 0 0 0 0 0 NOTES: [1] Indicates Module has COM Port 1 configured for ASYNC. The AM8530's port B is configured for COM1. [2] This Module contains the DEFA - Hardware Filtering. CAMS must be programmed (can contain 2 - 6 CAMS onboard). [3] The AM8530 has been removed (depopulated) from this module. Programming this device should not be performed. [4] Contains Dual Defa hardware. (Can be depopulated) [5] Depop'd two ports of hardware to make Dual Ethernet module. [6] These are FDDI modules. The ID cannot be read from the Link module I/O space. [7] These are FNS Platform Integrated 'Modules' - Cannot be detached or be used by any other platform.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER enet1(1), enet2(8), sync1(16), sync1a(17), t11(24), dse1(32), dse1a(33), dst416(40), sst416a(41), dst4(42), sst4a(43), sst416(44), stok416(45), sst4(46), stok4(47), floppy(48), t12(56), t12a(57), st1(58), t156k(60), e1(61), st156k(62), se1(63), t12n(64), st1n(65), t156kn(66), st156kn(67), e1n(68), se1n(69), sync(80), sync2a(81), cmcfddi(88), iphfddi(89), dt(104), dsde1(112), dsde1a(113), enet(114), dse2(116), dse2a(117), sse(118), ssea(119), dsde10bt(120), enet3(132), dsde2(156), oldqenf(160), denf(161), qenf(162), qef(164), def(165), mct1(168), dtok(176), mce1(184), wffddi2m(192), wffddi1m(193), wffddi2s(194), wffddi1s(195), wffddi2mf(196), wffddi1mf(197), wffddi2sf(198), wffddi1sf(199), fnsdse(208), fnsdsdt(216), fnsdst(217), dhssi(224), shssi(225), srml(8448)  

wfHwModRev 1.3.6.1.4.1.18.3.1.2.1.3
The revision level of the module. High byte is in upper 2 bytes.
Status: mandatory Access: read-only
OBJECT-TYPE    
  OCTET STRING  

wfHwModSerialNumber 1.3.6.1.4.1.18.3.1.2.1.4
The serial number of the module.
Status: mandatory Access: read-only
OBJECT-TYPE    
  OCTET STRING  

wfHwMotherBdIdOpt 1.3.6.1.4.1.18.3.1.2.1.5
The mother board identification number.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER sysctrl(1), ace12(2), ace25(3), ace32(4), fns(5), in(6), fre(256), srmf(8704)  

wfHwMotherBdRev 1.3.6.1.4.1.18.3.1.2.1.6
The revision level of the mother board. High byte is in upper 2 bytes.
Status: mandatory Access: read-only
OBJECT-TYPE    
  OCTET STRING  

wfHwMotherBdSerialNumber 1.3.6.1.4.1.18.3.1.2.1.7
The serial number of the mother board.
Status: mandatory Access: read-only
OBJECT-TYPE    
  OCTET STRING  

wfHwDaughterBdIdOpt 1.3.6.1.4.1.18.3.1.2.1.8
The daughter board identification number.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER sysctrl(1), ace68020mhz12(2), ace68020mhz25(3), ace68030mhz32(4), fre68040mhz25(4352), fre68040mhz33(4608)  

wfHwDaughterBdRev 1.3.6.1.4.1.18.3.1.2.1.9
The revision level of the daughter board. High byte is in upper 2 bytes.
Status: mandatory Access: read-only
OBJECT-TYPE    
  OCTET STRING  

wfHwDaughterBdSerialNumber 1.3.6.1.4.1.18.3.1.2.1.10
The serial number of the daughter board.
Status: mandatory Access: read-only
OBJECT-TYPE    
  OCTET STRING  

wfHwBabyBdIdOpt 1.3.6.1.4.1.18.3.1.2.1.11
The baby board identification number.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER  

wfHwBabyBdRev 1.3.6.1.4.1.18.3.1.2.1.12
The revision level of the baby board. High byte is in upper 2 bytes.
Status: mandatory Access: read-only
OBJECT-TYPE    
  OCTET STRING  

wfHwBabyBdSerialNumber 1.3.6.1.4.1.18.3.1.2.1.13
The serial number of the baby board.
Status: mandatory Access: read-only
OBJECT-TYPE    
  OCTET STRING  

wfHwDiagPromRev 1.3.6.1.4.1.18.3.1.2.1.14
The revision level of the Diagnostic PROM. Major revision level is in the upper 2 bytes, minor revision level in the lower 2 bytes.
Status: mandatory Access: read-only
OBJECT-TYPE    
  OCTET STRING  

wfHwDiagPromDate 1.3.6.1.4.1.18.3.1.2.1.15
The creation date of the Diagnostic PROM
Status: mandatory Access: read-only
OBJECT-TYPE    
  DisplayString  

wfHwDiagPromSource 1.3.6.1.4.1.18.3.1.2.1.16
The origin of the Diagnostic PROM contents
Status: mandatory Access: read-only
OBJECT-TYPE    
  DisplayString  

wfHwBootPromRev 1.3.6.1.4.1.18.3.1.2.1.17
The revision level of the BOOT PROM. Major revision level is in the upper 2 bytes, minor revision level in the lower 2 bytes.
Status: mandatory Access: read-only
OBJECT-TYPE    
  OCTET STRING  

wfHwBootPromDate 1.3.6.1.4.1.18.3.1.2.1.18
The creation date of the Boot PROM
Status: mandatory Access: read-only
OBJECT-TYPE    
  DisplayString  

wfHwBootPromSource 1.3.6.1.4.1.18.3.1.2.1.19
The origin of the Boot PROM contents
Status: mandatory Access: read-only
OBJECT-TYPE    
  DisplayString  

wfHwSparePromRev 1.3.6.1.4.1.18.3.1.2.1.20
The revision level of the BOOT PROM. Major revision level is in the upper 2 bytes, minor revision level in the lower 2 bytes.
Status: mandatory Access: read-only
OBJECT-TYPE    
  OCTET STRING  

wfHwSparePromDate 1.3.6.1.4.1.18.3.1.2.1.21
The creation date of the Spare PROM
Status: mandatory Access: read-only
OBJECT-TYPE    
  DisplayString  

wfHwSparePromSource 1.3.6.1.4.1.18.3.1.2.1.22
The origin of the Spare PROM contents
Status: mandatory Access: read-only
OBJECT-TYPE    
  DisplayString  

wfHwFileSysPresent 1.3.6.1.4.1.18.3.1.2.1.23
Flag indicating presence of File System on this slot.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER filesys(1), nofilesys(2)  

wfHssiTable 1.3.6.1.4.1.18.3.4.7
HSSI line record
Status: mandatory Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    WfHssiEntry

wfHssiEntry 1.3.6.1.4.1.18.3.4.7.1
An entry in the HSSI table
Status: mandatory Access: not-accessible
OBJECT-TYPE    
  WfHssiEntry  

wfHssiDelete 1.3.6.1.4.1.18.3.4.7.1.1
Create/Delete parameter
Status: mandatory Access: read-write
OBJECT-TYPE    
  INTEGER created(1), deleted(2)  

wfHssiDisable 1.3.6.1.4.1.18.3.4.7.1.2
Enable/Disable parameter
Status: mandatory Access: read-write
OBJECT-TYPE    
  INTEGER enabled(1), disabled(2)  

wfHssiState 1.3.6.1.4.1.18.3.4.7.1.3
Line Driver state variable, Not Present, Init, Down, Up
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER up(1), lmiwait(2), boflwait(3), cawait(4), init(5), notpresent(6)  

wfHssiSlot 1.3.6.1.4.1.18.3.4.7.1.4
Instance ID Slot, filled in by driver
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER minimum(1), maximum(14)  

wfHssiConnector 1.3.6.1.4.1.18.3.4.7.1.5
Instance ID Connector, filled in by driver
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER one(1), two(2), three(3), four(4)  

wfHssiCct 1.3.6.1.4.1.18.3.4.7.1.6
CCT number for this line instance
Status: mandatory Access: read-write
OBJECT-TYPE    
  INTEGER minimum(1), maximum(1023)  

wfHssiBofl 1.3.6.1.4.1.18.3.4.7.1.7
breath of life parameter
Status: mandatory Access: read-write
OBJECT-TYPE    
  INTEGER enabled(1), disabled(2)  

wfHssiBoflTmo 1.3.6.1.4.1.18.3.4.7.1.8
breath of life frequency in seconds
Status: mandatory Access: read-write
OBJECT-TYPE    
  INTEGER minimum(1), maximum(60), default(1)  

wfHssiMtu 1.3.6.1.4.1.18.3.4.7.1.9
MTU parameter, this is buffer size for HSSI media, fixed
Status: mandatory Access: read-write
OBJECT-TYPE    
  INTEGER minimum(3), maximum(4500), default(4495)  

wfHssiMadr 1.3.6.1.4.1.18.3.4.7.1.10
Line MAC address, fixed - line driver fills in from the 48 bit address stored in the serial number prom for this connector.
Status: mandatory Access: read-only
OBJECT-TYPE    
  OCTET STRING  

wfHssiService 1.3.6.1.4.1.18.3.4.7.1.11
Service type for this circuit. Transparent is raw HDLC mode, and is the only service provided on the current HSSI product
Status: mandatory Access: read-write
OBJECT-TYPE    
  INTEGER transparent(1), undefined(2)  

wfHssiWanProtocol 1.3.6.1.4.1.18.3.4.7.1.12
WAN protocol selection is provided via this parameter. The supported protocols can be selected per interface.
Status: mandatory Access: read-write
OBJECT-TYPE    
  INTEGER standard(1), passthru(2), ppp(3), smds(4), framerelay(5)  

wfHssiTransmissionInterface 1.3.6.1.4.1.18.3.4.7.1.13
T1 or T3, in the future OC1, OC3 and OC12. Used for MIB selection
Status: mandatory Access: read-write
OBJECT-TYPE    
  INTEGER dsone(1), dsthree(3)  

wfHssiExternalClkSpeed 1.3.6.1.4.1.18.3.4.7.1.14
External Clock Speed, Used in the future for route selection
Status: mandatory Access: read-write
OBJECT-TYPE    
  INTEGER minimum(307200), maximum(52638515), default(46359642)  

wfHssiCrcSize 1.3.6.1.4.1.18.3.4.7.1.15
CRC size parameter, 16 bit standard CCITT or extended 32 bit CRC
Status: mandatory Access: read-write
OBJECT-TYPE    
  INTEGER crc16bit(1), crc32bit(2)  

wfHssiInternalClkTestMode 1.3.6.1.4.1.18.3.4.7.1.16
Enables internal transmit clock generation. Should NEVER be enabled for normal operation.
Status: mandatory Access: read-write
OBJECT-TYPE    
  INTEGER enabled(1), disabled(2)  

wfHssiRxOctets 1.3.6.1.4.1.18.3.4.7.1.17
Number of bytes received without error
Status: mandatory Access: read-only
OBJECT-TYPE    
  Counter  

wfHssiRxFrames 1.3.6.1.4.1.18.3.4.7.1.18
Number of frames received without error
Status: mandatory Access: read-only
OBJECT-TYPE    
  Counter  

wfHssiTxOctets 1.3.6.1.4.1.18.3.4.7.1.19
Number of bytes transmitted without error
Status: mandatory Access: read-only
OBJECT-TYPE    
  Counter  

wfHssiTxFrames 1.3.6.1.4.1.18.3.4.7.1.20
Number of frames transmitted without error
Status: mandatory Access: read-only
OBJECT-TYPE    
  Counter  

wfHssiInDiscards 1.3.6.1.4.1.18.3.4.7.1.21
Number of error-free inbound packets discarded. Usually due to lack of memory resources.
Status: mandatory Access: read-only
OBJECT-TYPE    
  Counter  

wfHssiInErrors 1.3.6.1.4.1.18.3.4.7.1.22
Number of inbound packets not delivered to higher-layer protocol because of errors.
Status: mandatory Access: read-only
OBJECT-TYPE    
  Counter  

wfHssiOutDiscards 1.3.6.1.4.1.18.3.4.7.1.23
Number of error-free outbound packets discarded. Usually due to lack of transmission bandwidth.
Status: mandatory Access: read-only
OBJECT-TYPE    
  Counter  

wfHssiOutErrors 1.3.6.1.4.1.18.3.4.7.1.24
Number of outbound packets that could not be transmitted because of errors.
Status: mandatory Access: read-only
OBJECT-TYPE    
  Counter  

wfHssiRxLongFrames 1.3.6.1.4.1.18.3.4.7.1.25
Number of Long frames dropped on receive because of length
Status: mandatory Access: read-only
OBJECT-TYPE    
  Counter  

wfHssiTxClipFrames 1.3.6.1.4.1.18.3.4.7.1.26
Number of frames clipped in the transmit routine
Status: mandatory Access: read-only
OBJECT-TYPE    
  Counter  

wfHssiRxReplenMisses 1.3.6.1.4.1.18.3.4.7.1.27
Number of failed attempts by the line driver to aquire a packet buffer
Status: mandatory Access: read-only
OBJECT-TYPE    
  Counter  

wfHssiLastRxErrorCtrl 1.3.6.1.4.1.18.3.4.7.1.28
Last errored receive descriptor's control field
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER  

wfHssiRxCrcErrors 1.3.6.1.4.1.18.3.4.7.1.29
Number of frames received with CRC errors
Status: mandatory Access: read-only
OBJECT-TYPE    
  Counter  

wfHssiRxOverruns 1.3.6.1.4.1.18.3.4.7.1.30
Number of frames received with fifo overrun errors
Status: mandatory Access: read-only
OBJECT-TYPE    
  Counter  

wfHssiRxAborts 1.3.6.1.4.1.18.3.4.7.1.31
Number of frames received with abort status
Status: mandatory Access: read-only
OBJECT-TYPE    
  Counter  

wfHssiLastTxErrorCtrl 1.3.6.1.4.1.18.3.4.7.1.32
Last errored transmit descriptor's control field
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER  

wfHssiTxAborts 1.3.6.1.4.1.18.3.4.7.1.33
Number of transmit frames with internal abort errors
Status: mandatory Access: read-only
OBJECT-TYPE    
  Counter  

wfHssiTxUnderruns 1.3.6.1.4.1.18.3.4.7.1.34
Number of transmit frames aborted with underrun errors
Status: mandatory Access: read-only
OBJECT-TYPE    
  Counter  

wfHssiRxRingErrors 1.3.6.1.4.1.18.3.4.7.1.35
Number of receive ring error events
Status: mandatory Access: read-only
OBJECT-TYPE    
  Counter  

wfHssiLastRxRingState 1.3.6.1.4.1.18.3.4.7.1.36
Last 8 bit value from the recv ring state register
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER  

wfHssiRxRingOverruns 1.3.6.1.4.1.18.3.4.7.1.37
Number of receive ring overrun events
Status: mandatory Access: read-only
OBJECT-TYPE    
  Counter  

wfHssiTxRingErrors 1.3.6.1.4.1.18.3.4.7.1.38
Number of transmit ring error events
Status: mandatory Access: read-only
OBJECT-TYPE    
  Counter  

wfHssiLastTxRingState 1.3.6.1.4.1.18.3.4.7.1.39
Last 8 bit value from the transmit ring state register
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER  

wfHssiPortOpErrors 1.3.6.1.4.1.18.3.4.7.1.40
Number of port operation error events
Status: mandatory Access: read-only
OBJECT-TYPE    
  Counter  

wfHssiInternOpErrors 1.3.6.1.4.1.18.3.4.7.1.41
Number of internal operation error events
Status: mandatory Access: read-only
OBJECT-TYPE    
  Counter  

wfHssiHostErrors 1.3.6.1.4.1.18.3.4.7.1.42
Number of parity errs on host accesses to directly accessable registers.
Status: mandatory Access: read-only
OBJECT-TYPE    
  Counter  

wfHssiRxProcessings 1.3.6.1.4.1.18.3.4.7.1.43
Number of receive frame processings (RINT)
Status: mandatory Access: read-only
OBJECT-TYPE    
  Counter  

wfHssiTxProcessings 1.3.6.1.4.1.18.3.4.7.1.44
Number of transmit processings, invokations of transmit routine
Status: mandatory Access: read-only
OBJECT-TYPE    
  Counter  

wfHssiTxCmplProcessings 1.3.6.1.4.1.18.3.4.7.1.45
Number of transmit complete processings (TINT)
Status: mandatory Access: read-only
OBJECT-TYPE    
  Counter  

wfHssiIntrProcessings 1.3.6.1.4.1.18.3.4.7.1.46
Number of Interrupt processings, invokations of intr routine
Status: mandatory Access: read-only
OBJECT-TYPE    
  Counter  

wfHssiBoflNum 1.3.6.1.4.1.18.3.4.7.1.47
Number of breath of life packets per breath of life
Status: mandatory Access: read-write
OBJECT-TYPE    
  INTEGER minimum(1), maximum(127), default(5)  

wfHssiBoflLen 1.3.6.1.4.1.18.3.4.7.1.48
breath of life packet length
Status: mandatory Access: read-write
OBJECT-TYPE    
  INTEGER minimum(22), maximum(4450), default(100)  

wfHssiRxBufferLength 1.3.6.1.4.1.18.3.4.7.1.49
Performance tunning parameter controls Receive buffer size.
Status: mandatory Access: read-write
OBJECT-TYPE    
  INTEGER length4k(64), length8k(128)  

wfHssiMemPageLength 1.3.6.1.4.1.18.3.4.7.1.50
Performance tunning parameter controls device memory access burst length.
Status: mandatory Access: read-write
OBJECT-TYPE    
  INTEGER length32(1), length256(3)  

wfHssiRxRingLength 1.3.6.1.4.1.18.3.4.7.1.51
Performance tunning parameter controls the receive queue length. Receive Queue Length, values larger than the compiled ring size are truncated to the compiled ring size.
Status: mandatory Access: read-write
OBJECT-TYPE    
  INTEGER minimum(1), maximum(255), default(64)  

wfHssiTxRingLength 1.3.6.1.4.1.18.3.4.7.1.52
Performance tunning parameter controls the transmit queue length. Transmit Queue Length, values larger than the compiled ring size are truncated to the compiled ring size.
Status: mandatory Access: read-write
OBJECT-TYPE    
  INTEGER minimum(1), maximum(255), default(127)  

wfHssiRxFifoWatermark 1.3.6.1.4.1.18.3.4.7.1.53
Performance tunning parameter controls the receive watermark.
Status: mandatory Access: read-write
OBJECT-TYPE    
  INTEGER minimum(2), maximum(255), default(2)  

wfHssiTxFifoWatermark 1.3.6.1.4.1.18.3.4.7.1.54
Performance tunning parameter controls the transmit watermark.
Status: mandatory Access: read-write
OBJECT-TYPE    
  INTEGER minimum(2), maximum(255), default(16)  

wfHssiMaxRxMemory 1.3.6.1.4.1.18.3.4.7.1.55
Performance tunning parameter controls fifo area allowed for receive.
Status: mandatory Access: read-write
OBJECT-TYPE    
  INTEGER minimum(1), maximum(255), default(1)  

wfHssiLinkInterface 1.3.6.1.4.1.18.3.4.7.1.56
Only for DEBUG.
Status: mandatory Access: read-write
OBJECT-TYPE    
  INTEGER default(1), ace25(2), ace32(3)  

wfHssiTurboBofl 1.3.6.1.4.1.18.3.4.7.1.57
Only for DEBUG, Turbo breath of life parameter
Status: mandatory Access: read-write
OBJECT-TYPE    
  INTEGER enabled(1), disabled(2)  

wfHwfTable 1.3.6.1.4.1.18.3.4.6.1
The following table will contain information about a collection of Hardware Filter (HWF) driver records. Only one HWF driver may be spawned, by the loader, on a given slot. Hence, only the slot number is used as the instance identifier into the table.
Status: mandatory Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    WfHwfEntry

wfHwfEntry 1.3.6.1.4.1.18.3.4.6.1.1
Slot number used as instance identifier.
Status: mandatory Access: not-accessible
OBJECT-TYPE    
  WfHwfEntry  

wfHwfDelete 1.3.6.1.4.1.18.3.4.6.1.1.1
Create/delete parameter.
Status: mandatory Access: read-write
OBJECT-TYPE    
  INTEGER created(1), deleted(2)  

wfHwfEnable 1.3.6.1.4.1.18.3.4.6.1.1.2
Enable/disable parameter.
Status: mandatory Access: read-write
OBJECT-TYPE    
  INTEGER enabled(1), disabled(2)  

wfHwfState 1.3.6.1.4.1.18.3.4.6.1.1.3
Driver state variable.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER up(1), down(2), init(3), notpresent(4)  

wfHwfSlot 1.3.6.1.4.1.18.3.4.6.1.1.4
Slot number -- instance ID.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER minimum(1), maximum(14)  

wfHwfAvailableLines 1.3.6.1.4.1.18.3.4.6.1.1.5
Number of available lines on module.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER  

wfHwfLineTable 1.3.6.1.4.1.18.3.4.6.2
The following table will contain information about a collection of Hardware Filter (HWF) line records.
Status: mandatory Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    WfHwfLineEntry

wfHwfLineEntry 1.3.6.1.4.1.18.3.4.6.2.1
Slot number and line number used as instance identifier.
Status: mandatory Access: not-accessible
OBJECT-TYPE    
  WfHwfLineEntry  

wfHwfLineState 1.3.6.1.4.1.18.3.4.6.2.1.1
State of filtering hardware on a per line basis.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER operational(1), disabled(2), full(3)  

wfHwfLineSlot 1.3.6.1.4.1.18.3.4.6.2.1.2
Slot number -- instance ID.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER  

wfHwfLineNumber 1.3.6.1.4.1.18.3.4.6.2.1.3
Line number -- instance ID.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER one(1), two(2), three(3), four(4)  

wfHwfLineCct 1.3.6.1.4.1.18.3.4.6.2.1.4
Circuit number associated with a line.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER  

wfHwfLineCapableMaxTblSize 1.3.6.1.4.1.18.3.4.6.2.1.5
This attribute specifies the maximum number of table entries capable of being used by a line based upon actual hardware filter devices present and available.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER  

wfHwfLineCurrentTblSize 1.3.6.1.4.1.18.3.4.6.2.1.6
Current capacity of the hardware filter table. Hardware filter table resources are dynamically allocated (in increments of 256) on an as-needed basis up to the available table size.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER  

wfHwfLineCurrentUsedEntries 1.3.6.1.4.1.18.3.4.6.2.1.7
Number of hardware filter table entries used.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER  

wfHwfLineDroppedFrames 1.3.6.1.4.1.18.3.4.6.2.1.8
Number of frames dropped because of hardware filter match.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER  

wfMod 1.3.6.1.4.1.18.3.1.3
OBJECT IDENTIFIER    

wfModState 1.3.6.1.4.1.18.3.1.3.1
State of this record
Status: mandatory Access: not-accessible
OBJECT-TYPE    
  INTEGER init(1)  

wfModSlot 1.3.6.1.4.1.18.3.1.3.2
Instance of this record
Status: mandatory Access: not-accessible
OBJECT-TYPE    
  INTEGER  

wfModIdOpt 1.3.6.1.4.1.18.3.1.3.3
actual module ID and Option
Status: mandatory Access: not-accessible
OBJECT-TYPE    
  INTEGER  

wfModRev 1.3.6.1.4.1.18.3.1.3.4
actual module Revision
Status: mandatory Access: not-accessible
OBJECT-TYPE    
  INTEGER  

wfModProm 1.3.6.1.4.1.18.3.1.3.5
module PROM
Status: mandatory Access: not-accessible
OBJECT-TYPE    
  INTEGER  

wfModMidr 1.3.6.1.4.1.18.3.1.3.6
module ID register
Status: mandatory Access: not-accessible
OBJECT-TYPE    
  INTEGER  

wfModMled 1.3.6.1.4.1.18.3.1.3.7
module LED register
Status: mandatory Access: not-accessible
OBJECT-TYPE    
  INTEGER  

wfModMisr 1.3.6.1.4.1.18.3.1.3.8
module MISR register
Status: mandatory Access: not-accessible
OBJECT-TYPE    
  INTEGER  

wfModSnprom 1.3.6.1.4.1.18.3.1.3.9
module SNPROM
Status: mandatory Access: not-accessible
OBJECT-TYPE    
  INTEGER  

wfModMadr1 1.3.6.1.4.1.18.3.1.3.10
SNPROM MAC address connector 1
Status: mandatory Access: not-accessible
OBJECT-TYPE    
  OCTET STRING  

wfModMadr2 1.3.6.1.4.1.18.3.1.3.11
SNPROM MAC address connector 2
Status: mandatory Access: not-accessible
OBJECT-TYPE    
  OCTET STRING  

wfModMadr3 1.3.6.1.4.1.18.3.1.3.12
SNPROM MAC address connector 3
Status: mandatory Access: not-accessible
OBJECT-TYPE    
  OCTET STRING  

wfModMadr4 1.3.6.1.4.1.18.3.1.3.13
SNPROM MAC address connector 4
Status: mandatory Access: not-accessible
OBJECT-TYPE    
  OCTET STRING  

wfModLance1 1.3.6.1.4.1.18.3.1.3.14
LANCE line 1
Status: mandatory Access: not-accessible
OBJECT-TYPE    
  INTEGER  

wfModLance2 1.3.6.1.4.1.18.3.1.3.15
LANCE line 2
Status: mandatory Access: not-accessible
OBJECT-TYPE    
  INTEGER  

wfModMk50251 1.3.6.1.4.1.18.3.1.3.16
MK5025 line 1
Status: mandatory Access: not-accessible
OBJECT-TYPE    
  INTEGER  

wfModMk50252 1.3.6.1.4.1.18.3.1.3.17
MK5025 line 2
Status: mandatory Access: not-accessible
OBJECT-TYPE    
  INTEGER  

wfModMk50253 1.3.6.1.4.1.18.3.1.3.18
MK5025 line 3
Status: mandatory Access: not-accessible
OBJECT-TYPE    
  INTEGER  

wfModMk50254 1.3.6.1.4.1.18.3.1.3.19
MK5025 line 4
Status: mandatory Access: not-accessible
OBJECT-TYPE    
  INTEGER  

wfModSicr 1.3.6.1.4.1.18.3.1.3.20
SYNC interface control register
Status: mandatory Access: not-accessible
OBJECT-TYPE    
  INTEGER  

wfModSbrr 1.3.6.1.4.1.18.3.1.3.21
SYNC baudrate register
Status: mandatory Access: not-accessible
OBJECT-TYPE    
  INTEGER  

wfMod8530 1.3.6.1.4.1.18.3.1.3.22
8530 DUART
Status: mandatory Access: not-accessible
OBJECT-TYPE    
  INTEGER  

wfModCar 1.3.6.1.4.1.18.3.1.3.23
CAM assembly register
Status: mandatory Access: not-accessible
OBJECT-TYPE    
  INTEGER  

wfModDefaA 1.3.6.1.4.1.18.3.1.3.24
DEFA A chip
Status: mandatory Access: not-accessible
OBJECT-TYPE    
  INTEGER  

wfModCamALock 1.3.6.1.4.1.18.3.1.3.25
CAM A lock
Status: mandatory Access: not-accessible
OBJECT-TYPE    
  INTEGER  

wfModCamAUnlock 1.3.6.1.4.1.18.3.1.3.26
CAM A unlock
Status: mandatory Access: not-accessible
OBJECT-TYPE    
  INTEGER  

wfModDefaB 1.3.6.1.4.1.18.3.1.3.27
DEFA B chip
Status: mandatory Access: not-accessible
OBJECT-TYPE    
  INTEGER  

wfModCamBLock 1.3.6.1.4.1.18.3.1.3.28
CAM B lock
Status: mandatory Access: not-accessible
OBJECT-TYPE    
  INTEGER  

wfModCamBUnlock 1.3.6.1.4.1.18.3.1.3.29
CAM B unlock
Status: mandatory Access: not-accessible
OBJECT-TYPE    
  INTEGER  

wfModIlacc1 1.3.6.1.4.1.18.3.1.3.30
ILACC line 1
Status: mandatory Access: not-accessible
OBJECT-TYPE    
  INTEGER  

wfModIlacc2 1.3.6.1.4.1.18.3.1.3.31
ILACC line 2
Status: mandatory Access: not-accessible
OBJECT-TYPE    
  INTEGER  

wfModIlacc3 1.3.6.1.4.1.18.3.1.3.32
ILACC line 3
Status: mandatory Access: not-accessible
OBJECT-TYPE    
  INTEGER  

wfModIlacc4 1.3.6.1.4.1.18.3.1.3.33
ILACC line 4
Status: mandatory Access: not-accessible
OBJECT-TYPE    
  INTEGER  

wfModTms3801 1.3.6.1.4.1.18.3.1.3.34
TOKEN ring chip line 1
Status: mandatory Access: not-accessible
OBJECT-TYPE    
  INTEGER  

wfModTms3802 1.3.6.1.4.1.18.3.1.3.35
TOKEN ring chip line 2
Status: mandatory Access: not-accessible
OBJECT-TYPE    
  INTEGER  

wfModTocr 1.3.6.1.4.1.18.3.1.3.36
TOKEN control register
Status: mandatory Access: not-accessible
OBJECT-TYPE    
  INTEGER  

wfModTsra 1.3.6.1.4.1.18.3.1.3.37
TOKEN source route accelerator
Status: mandatory Access: not-accessible
OBJECT-TYPE    
  INTEGER  

wfModMuxram1 1.3.6.1.4.1.18.3.1.3.38
T1 mux RAM active
Status: mandatory Access: not-accessible
OBJECT-TYPE    
  INTEGER  

wfModMuxram2 1.3.6.1.4.1.18.3.1.3.39
T1 mux RAM inactive
Status: mandatory Access: not-accessible
OBJECT-TYPE    
  INTEGER  

wfModTicr 1.3.6.1.4.1.18.3.1.3.40
T1 interface control register
Status: mandatory Access: not-accessible
OBJECT-TYPE    
  INTEGER  

wfModFramer1 1.3.6.1.4.1.18.3.1.3.41
T1 framer line 1
Status: mandatory Access: not-accessible
OBJECT-TYPE    
  INTEGER  

wfModFramer2 1.3.6.1.4.1.18.3.1.3.42
T1 framer line 2
Status: mandatory Access: not-accessible
OBJECT-TYPE    
  INTEGER  

wfModFsi1 1.3.6.1.4.1.18.3.1.3.43
FDDI FSI line 1
Status: mandatory Access: not-accessible
OBJECT-TYPE    
  INTEGER  

wfModMac1 1.3.6.1.4.1.18.3.1.3.44
FDDI MAC line 1
Status: mandatory Access: not-accessible
OBJECT-TYPE    
  INTEGER  

wfModElmA1 1.3.6.1.4.1.18.3.1.3.45
FDDI ELM A line 1
Status: mandatory Access: not-accessible
OBJECT-TYPE    
  INTEGER  

wfModElmB1 1.3.6.1.4.1.18.3.1.3.46
FDDI ELM B line 1
Status: mandatory Access: not-accessible
OBJECT-TYPE    
  INTEGER  

wfModMcr1 1.3.6.1.4.1.18.3.1.3.47
FDDI Module control register line 1
Status: mandatory Access: not-accessible
OBJECT-TYPE    
  INTEGER  

wfModHssiFsi1 1.3.6.1.4.1.18.3.1.3.48
HSSI FSI line 1
Status: mandatory Access: not-accessible
OBJECT-TYPE    
  INTEGER  

wfModHssiFsi2 1.3.6.1.4.1.18.3.1.3.49
HSSI FSI line 2
Status: mandatory Access: not-accessible
OBJECT-TYPE    
  INTEGER  

wfModHssiUga1 1.3.6.1.4.1.18.3.1.3.50
HSSI UGA-330-2 line 1
Status: mandatory Access: not-accessible
OBJECT-TYPE    
  INTEGER  

wfModHssiUga2 1.3.6.1.4.1.18.3.1.3.51
HSSI UGA-330-2 line 2
Status: mandatory Access: not-accessible
OBJECT-TYPE    
  INTEGER  

wfModHicr 1.3.6.1.4.1.18.3.1.3.52
HSSI Control Register address
Status: mandatory Access: not-accessible
OBJECT-TYPE    
  INTEGER  

wfModHicrData 1.3.6.1.4.1.18.3.1.3.53
HSSI Last value written to the HICR
Status: mandatory Access: not-accessible
OBJECT-TYPE    
  INTEGER  

wfModHlsr 1.3.6.1.4.1.18.3.1.3.54
HSSI Line Status Register address
Status: mandatory Access: not-accessible
OBJECT-TYPE    
  INTEGER  

wfModHlsrData 1.3.6.1.4.1.18.3.1.3.55
HSSI Last value read from HLSR
Status: mandatory Access: not-accessible
OBJECT-TYPE    
  INTEGER  

wfIf 1.3.6.1.4.1.18.3.5.1.3.1
OBJECT IDENTIFIER    

wfIfNumber 1.3.6.1.4.1.18.3.5.1.3.1.1
Total number of possible active interfaces
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER  

wfIfTable 1.3.6.1.4.1.18.3.5.1.3.2
A table containing active interfaces
Status: mandatory Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    WfIfEntry

wfIfEntry 1.3.6.1.4.1.18.3.5.1.3.2.1
A particular interface
Status: mandatory Access: not-accessible
OBJECT-TYPE    
  WfIfEntry  

wfIfIndex 1.3.6.1.4.1.18.3.5.1.3.2.1.1
Corresponds to same attribute of MIB-II's ifTable
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER  

wfIfDescr 1.3.6.1.4.1.18.3.5.1.3.2.1.2
Corresponds to same attribute of MIB-II's ifTable
Status: mandatory Access: read-only
OBJECT-TYPE    
  DisplayString  

wfIfType 1.3.6.1.4.1.18.3.5.1.3.2.1.3
Corresponds to same attribute of MIB-II's ifTable
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER  

wfIfMtu 1.3.6.1.4.1.18.3.5.1.3.2.1.4
Corresponds to same attribute of MIB-II's ifTable
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER  

wfIfSpeed 1.3.6.1.4.1.18.3.5.1.3.2.1.5
Corresponds to same attribute of MIB-II's ifTable
Status: mandatory Access: read-only
OBJECT-TYPE    
  Gauge  

wfIfPhysAddress 1.3.6.1.4.1.18.3.5.1.3.2.1.6
Corresponds to same attribute of MIB-II's ifTable
Status: mandatory Access: read-only
OBJECT-TYPE    
  OCTET STRING  

wfIfAdminStatus 1.3.6.1.4.1.18.3.5.1.3.2.1.7
Corresponds to same attribute of MIB-II's ifTable
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER  

wfIfOperStatus 1.3.6.1.4.1.18.3.5.1.3.2.1.8
Corresponds to same attribute of MIB-II's ifTable
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER  

wfIfLastChange 1.3.6.1.4.1.18.3.5.1.3.2.1.9
Corresponds to same attribute of MIB-II's ifTable
Status: mandatory Access: read-only
OBJECT-TYPE    
  TimeTicks  

wfIfInOctets 1.3.6.1.4.1.18.3.5.1.3.2.1.10
Corresponds to same attribute of MIB-II's ifTable
Status: mandatory Access: read-only
OBJECT-TYPE    
  Counter  

wfIfInUcastPkts 1.3.6.1.4.1.18.3.5.1.3.2.1.11
Corresponds to same attribute of MIB-II's ifTable
Status: mandatory Access: read-only
OBJECT-TYPE    
  Counter  

wfIfInNUCastPkts 1.3.6.1.4.1.18.3.5.1.3.2.1.12
Corresponds to same attribute of MIB-II's ifTable
Status: mandatory Access: read-only
OBJECT-TYPE    
  Counter  

wfIfInDiscards 1.3.6.1.4.1.18.3.5.1.3.2.1.13
Corresponds to same attribute of MIB-II's ifTable
Status: mandatory Access: read-only
OBJECT-TYPE    
  Counter  

wfIfInErrors 1.3.6.1.4.1.18.3.5.1.3.2.1.14
Corresponds to same attribute of MIB-II's ifTable
Status: mandatory Access: read-only
OBJECT-TYPE    
  Counter  

wfIfInUnknownProtos 1.3.6.1.4.1.18.3.5.1.3.2.1.15
Corresponds to same attribute of MIB-II's ifTable
Status: mandatory Access: read-only
OBJECT-TYPE    
  Counter  

wfIfOutOctets 1.3.6.1.4.1.18.3.5.1.3.2.1.16
Corresponds to same attribute of MIB-II's ifTable
Status: mandatory Access: read-only
OBJECT-TYPE    
  Counter  

wfIfOutUcastPkts 1.3.6.1.4.1.18.3.5.1.3.2.1.17
Corresponds to same attribute of MIB-II's ifTable
Status: mandatory Access: read-only
OBJECT-TYPE    
  Counter  

wfIfOutNUcastPkts 1.3.6.1.4.1.18.3.5.1.3.2.1.18
Corresponds to same attribute of MIB-II's ifTable
Status: mandatory Access: read-only
OBJECT-TYPE    
  Counter  

wfIfOutDiscards 1.3.6.1.4.1.18.3.5.1.3.2.1.19
Corresponds to same attribute of MIB-II's ifTable
Status: mandatory Access: read-only
OBJECT-TYPE    
  Counter  

wfIfOutErrors 1.3.6.1.4.1.18.3.5.1.3.2.1.20
Corresponds to same attribute of MIB-II's ifTable
Status: mandatory Access: read-only
OBJECT-TYPE    
  Counter  

wfIfOutQLen 1.3.6.1.4.1.18.3.5.1.3.2.1.21
Corresponds to same attribute of MIB-II's ifTable
Status: mandatory Access: read-only
OBJECT-TYPE    
  Gauge  

wfIfSpecific 1.3.6.1.4.1.18.3.5.1.3.2.1.22
Corresponds to same attribute of MIB-II's ifTable
Status: mandatory Access: read-only
OBJECT-TYPE    
  OBJECT IDENTIFIER  

wfIpBase 1.3.6.1.4.1.18.3.5.3.2.1.1
OBJECT IDENTIFIER    

wfIpBaseCreate 1.3.6.1.4.1.18.3.5.3.2.1.1.1
Create/Delete parameter. Default is created. Users perform a set operation on this object in order to create/delete IP.
Status: mandatory Access: read-write
OBJECT-TYPE    
  INTEGER created(1), deleted(2)  

wfIpBaseEnable 1.3.6.1.4.1.18.3.5.3.2.1.1.2
Enable/Disable parameter. Default is enabled. Users perform a set operation on this object in order to enable/disable IP.
Status: mandatory Access: read-write
OBJECT-TYPE    
  INTEGER enabled(1), disabled(2)  

wfIpBaseState 1.3.6.1.4.1.18.3.5.3.2.1.1.3
The current state of the entire IP.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER up(1), down(2), init(3), notpres(4)  

wfIpBaseForwarding 1.3.6.1.4.1.18.3.5.3.2.1.1.4
The indication of whether this entity is acting as an IP gateway in respect to the forwarding of datagrams received by, but not addressed to, this entity. IP gateways forward datagrams. IP hosts do not (except those source-routed via the host). Note that for some managed nodes, this object may take on only a subset of the values possible. Accordingly, it is appropriate for an agent to return a `badValue' response if a management station attempts to change this object to an inappropriate value.
Status: mandatory Access: read-write
OBJECT-TYPE    
  INTEGER forwarding(1), notforwarding(2)  

wfIpBaseDefaultTTL 1.3.6.1.4.1.18.3.5.3.2.1.1.5
The default value inserted into the Time-To-Live field of the IP header of datagrams originated at this entity, whenever a TTL value is not supplied by the transport layer protocol.
Status: mandatory Access: read-write
OBJECT-TYPE    
  INTEGER default(30), ttlmax(255)  

wfIpBaseRipDiameter 1.3.6.1.4.1.18.3.5.3.2.1.1.6
The Diameter of the RIP network. 1 less than 'infinity'
Status: mandatory Access: read-write
OBJECT-TYPE    
  INTEGER dflt(15), maximum(15)  

wfIpBaseRtEntryTable 1.3.6.1.4.1.18.3.5.3.2.1.2
The list of elements in IP's routing table
Status: mandatory Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    WfIpBaseRtEntry

wfIpBaseRtEntry 1.3.6.1.4.1.18.3.5.3.2.1.2.1
A description of a route
Status: mandatory Access: not-accessible
OBJECT-TYPE    
  WfIpBaseRtEntry  

wfIpBaseRouteDest 1.3.6.1.4.1.18.3.5.3.2.1.2.1.1
The destination IP address of this route. An entry with a value of 0.0.0.0 is considered a default route. Multiple routes to a single destination can appear in the table, but access to such multiple entries is dependent on the table- access mechanisms defined by the network management protocol in use.
Status: mandatory Access: read-only
OBJECT-TYPE    
  IpAddress  

wfIpBaseRouteIfIndex 1.3.6.1.4.1.18.3.5.3.2.1.2.1.2
The index value which uniquely identifies the local interface through which the next hop of this route should be reached. The interface identified by a particular value of this index is the same interface as identified by the same value of ifIndex.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER  

wfIpBaseRouteMetric1 1.3.6.1.4.1.18.3.5.3.2.1.2.1.3
The primary routing metric for this route. The semantics of this metric are determined by the routing-protocol specified in the route's ipRouteProto value. If this metric is not used, its value should be set to -1.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER  

wfIpBaseRouteMetric2 1.3.6.1.4.1.18.3.5.3.2.1.2.1.4
An alternate routing metric for this route. The semantics of this metric are determined by the routing-protocol specified in the route's ipRouteProto value. If this metric is not used, its value should be set to -1.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER  

wfIpBaseRouteMetric3 1.3.6.1.4.1.18.3.5.3.2.1.2.1.5
An alternate routing metric for this route. The semantics of this metric are determined by the routing-protocol specified in the route's ipRouteProto value. If this metric is not used, its value should be set to -1.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER  

wfIpBaseRouteMetric4 1.3.6.1.4.1.18.3.5.3.2.1.2.1.6
An alternate routing metric for this route. The semantics of this metric are determined by the routing-protocol specified in the route's ipRouteProto value. If this metric is not used, its value should be set to -1.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER  

wfIpBaseRouteNextHop 1.3.6.1.4.1.18.3.5.3.2.1.2.1.7
The IP address of the next hop of this route. (In the case of a route bound to an interface which is realized via a broadcast media, the value of this field is the agent's IP address on that interface.)
Status: mandatory Access: read-only
OBJECT-TYPE    
  IpAddress  

wfIpBaseRouteType 1.3.6.1.4.1.18.3.5.3.2.1.2.1.8
The type of route. Note that the values direct(3) and indirect(4) refer to the notion of direct and indirect routing in the IP architecture. Setting this object to the value invalid(2) has the effect of invalidating the corresponding entry in the ipRouteTable object. That is, it effectively dissasociates the destination identified with said entry from the route identified with said entry. It is an implementation-specific matter as to whether the agent removes an invalidated entry from the table. nagement stations must be prepared to receive tabular information from agents that corresponds to entries not currently in use. Proper interpretation of such entries requires examination of the relevant ipRouteType object.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER other(1), invalid(2), direct(3), indirect(4)  

wfIpBaseRouteProto 1.3.6.1.4.1.18.3.5.3.2.1.2.1.9
The routing mechanism via which this route was learned. Inclusion of values for gateway routing protocols is not intended to imply that hosts should support those protocols.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER other(1), local(2), netmgmt(3), icmp(4), egp(5), ggp(6), hello(7), rip(8), is(9), ospf(13), bgp(14)  

wfIpBaseRouteAge 1.3.6.1.4.1.18.3.5.3.2.1.2.1.10
The number of seconds since this route was last updated or otherwise determined to be correct. Note that no semantics of `too old' can be implied except through knowledge of the routing protocol by which the route was learned.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER  

wfIpBaseRouteMask 1.3.6.1.4.1.18.3.5.3.2.1.2.1.11
Indicate the mask to be logical-ANDed with the destination address before being compared to the value in the ipRouteDest field. For those systems that do not support arbitrary subnet masks, an agent constructs the value of the ipRouteMask by determining whether the value of the correspondent ipRouteDest field belong to a class-A, B, or C network, and then using one of: mask network 255.0.0.0 class-A 255.255.0.0 class-B 255.255.255.0 class-C If the value of the ipRouteDest is 0.0.0.0 (a default route), then the mask value is also 0.0.0.0. It should be noted that all IP routing subsystems implicitly use this mechanism.
Status: mandatory Access: read-only
OBJECT-TYPE    
  IpAddress  

wfIpBaseRouteMetric5 1.3.6.1.4.1.18.3.5.3.2.1.2.1.12
An alternate routing metric for this route. The semantics of this metric are determined by the routing-protocol specified in the route's ipRouteProto value. If this metric is not used, its value should be set to -1.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER  

wfIpBaseRouteInfo 1.3.6.1.4.1.18.3.5.3.2.1.2.1.13
A user-defined string which describes this Route entry
Status: mandatory Access: read-only
OBJECT-TYPE    
  OBJECT IDENTIFIER  

wfIpBaseHostEntryTable 1.3.6.1.4.1.18.3.5.3.2.1.3
The list of elements in IP's host table
Status: mandatory Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    WfIpBaseHostEntry

wfIpBaseHostEntry 1.3.6.1.4.1.18.3.5.3.2.1.3.1
A description of a resolved host
Status: mandatory Access: not-accessible
OBJECT-TYPE    
  WfIpBaseHostEntry  

wfIpBaseNetToMediaIfIndex 1.3.6.1.4.1.18.3.5.3.2.1.3.1.1
The interface on which this entry's equivalence is effective. The interface identified by a particular value of this index is the same interface as identified by the same value of ifIndex.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER  

wfIpBaseNetToMediaPhysAddress 1.3.6.1.4.1.18.3.5.3.2.1.3.1.2
The media-dependent `physical' address.
Status: mandatory Access: read-only
OBJECT-TYPE    
  OCTET STRING  

wfIpBaseNetToMediaNetAddress 1.3.6.1.4.1.18.3.5.3.2.1.3.1.3
The IpAddress corresponding to the media-dependent `physical' address.
Status: mandatory Access: read-only
OBJECT-TYPE    
  IpAddress  

wfIpBaseNetToMediaType 1.3.6.1.4.1.18.3.5.3.2.1.3.1.4
The type of mapping. Setting this object to the value invalid(2) has the effect of invalidating the corresponding entry in the ipNetToMediaTable. That is, it effectively dissasociates the interface identified with said entry from the mapping identified with said entry. It is an implementation-specific matter as to whether the agent removes an invalidated entry from the table. Accordingly, management stations must be prepared to receive tabular information from agents that corresponds to entries not currently in use. Proper interpretation of such entries requires examination of the relevant ipNetToMediaType object.
Status: mandatory Access: read-write
OBJECT-TYPE    
  INTEGER other(1), invalid(2), dynamic(3), static(4)  

wfIpInterfaceTable 1.3.6.1.4.1.18.3.5.3.2.1.4
The list of configured IP interface
Status: mandatory Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    WfIpInterfaceEntry

wfIpInterfaceEntry 1.3.6.1.4.1.18.3.5.3.2.1.4.1
An IP interface description
Status: mandatory Access: not-accessible
OBJECT-TYPE    
  WfIpInterfaceEntry  

wfIpInterfaceCreate 1.3.6.1.4.1.18.3.5.3.2.1.4.1.1
Create/Delete parameter. Default is created. Users perform a set operation on this object in order to create/delete an IP interface.
Status: mandatory Access: read-write
OBJECT-TYPE    
  INTEGER create(1), delete(2)  

wfIpInterfaceEnable 1.3.6.1.4.1.18.3.5.3.2.1.4.1.2
Enable/Disable parameter. Default is enabled. Users perform a set operation on this object in order to enable/disable an IP interface.
Status: mandatory Access: read-write
OBJECT-TYPE    
  INTEGER enable(1), disable(2)  

wfIpInterfaceState 1.3.6.1.4.1.18.3.5.3.2.1.4.1.3
INvalid indicates an error in processing the cfg record
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER up(1), down(2), init(3), invalid(4), notpres(5)  

wfIpInterfaceAddr 1.3.6.1.4.1.18.3.5.3.2.1.4.1.4
The IP Address to which this entry's addressing information pertains
Status: mandatory Access: read-only
OBJECT-TYPE    
  IpAddress  

wfIpInterfaceCircuit 1.3.6.1.4.1.18.3.5.3.2.1.4.1.5
The Circuit Number that this interface runs over
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER  

wfIpInterfaceMask 1.3.6.1.4.1.18.3.5.3.2.1.4.1.6
The subnet mask associated with the IP address of this entry. The value of the mask is an IP address with all the network bits set to 1 and all the hosts bits set to 0.
Status: mandatory Access: read-write
OBJECT-TYPE    
  IpAddress  

wfIpInterfaceCost 1.3.6.1.4.1.18.3.5.3.2.1.4.1.7
The Cost metric associated with the IP Address of this entry
Status: mandatory Access: read-write
OBJECT-TYPE    
  INTEGER  

wfIpInterfaceCfgBcastAddr 1.3.6.1.4.1.18.3.5.3.2.1.4.1.8
The user can specifcy a broadcast address for a NWIF
Status: mandatory Access: read-write
OBJECT-TYPE    
  IpAddress  

wfIpInterfaceBcastAddr 1.3.6.1.4.1.18.3.5.3.2.1.4.1.9
The value of the broadcast address used for sending datagrams on the (logical) interface associated with the IP address of this entry. This value applies to both the subnet and network broadcasts addresses used by the entity on this (logical) interface. This is value used by the software
Status: mandatory Access: read-only
OBJECT-TYPE    
  IpAddress  

wfIpInterfaceMTUDiscovery 1.3.6.1.4.1.18.3.5.3.2.1.4.1.10
Whether MTU discovery option is on/off
Status: mandatory Access: read-write
OBJECT-TYPE    
  INTEGER on(1), off(2)  

wfIpInterfaceAMR 1.3.6.1.4.1.18.3.5.3.2.1.4.1.11
Whether Address Mask Reply is ON/OFF
Status: mandatory Access: read-write
OBJECT-TYPE    
  INTEGER on(1), off(2)  

wfIpInterfaceASB 1.3.6.1.4.1.18.3.5.3.2.1.4.1.12
Whether All-Subnet Broadcasts Are excepted and Sent out this NWIF
Status: mandatory Access: read-write
OBJECT-TYPE    
  INTEGER on(1), off(2)  

wfIpInterfaceAddressResolutionType 1.3.6.1.4.1.18.3.5.3.2.1.4.1.13
Indicates which Address Resolution Type to use
Status: mandatory Access: read-write
OBJECT-TYPE    
  INTEGER arp(1), probe(2), ddn(3), pdn(4), inarp(5), arpinarp(6)  

wfIpInterfaceProxy 1.3.6.1.4.1.18.3.5.3.2.1.4.1.14
Indicates Whether Proxy is on this Interface or not
Status: mandatory Access: read-write
OBJECT-TYPE    
  INTEGER on(1), off(2)  

wfIpInterfaceHostCache 1.3.6.1.4.1.18.3.5.3.2.1.4.1.15
Whether the Host Cache (Address Aging) is on or not. A Range of discrete values is specified as well as a value meaning don't age
Status: mandatory Access: read-write
OBJECT-TYPE    
  INTEGER cacheoff(1), cache120(120), cache180(180), cache240(240), cache300(300), cache600(600), cache900(900), cache1200(1200)  

wfIpInterfaceUdpXsumOn 1.3.6.1.4.1.18.3.5.3.2.1.4.1.16
Whether to turn UDP checksum verification on for UDP packets recieved and transmitted by this router
Status: mandatory Access: read-write
OBJECT-TYPE    
  INTEGER on(1), off(2)  

wfIpInterfaceCfgMacAddress 1.3.6.1.4.1.18.3.5.3.2.1.4.1.17
The desired mac set by the user
Status: mandatory Access: read-write
OBJECT-TYPE    
  OCTET STRING  

wfIpInterfaceMacAddress 1.3.6.1.4.1.18.3.5.3.2.1.4.1.18
The MAC Address for this Interface- actual one used
Status: mandatory Access: read-only
OBJECT-TYPE    
  OCTET STRING  

wfIpInterfaceReasmMaxSize 1.3.6.1.4.1.18.3.5.3.2.1.4.1.19
The size of the largest IP datagram which this entity can re-assemble from incoming IP fragmented datagrams received on this interface.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER  

wfIpInterfaceMaxInfo 1.3.6.1.4.1.18.3.5.3.2.1.4.1.20
The maximum size of the INFO (non-MAC) field that this port will receive or transmit.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER  

wfIpInterfaceInReceives 1.3.6.1.4.1.18.3.5.3.2.1.4.1.21
The total number of input datagrams received from interfaces, including those received in error.
Status: mandatory Access: read-only
OBJECT-TYPE    
  Counter  

wfIpInterfaceInHdrErrors 1.3.6.1.4.1.18.3.5.3.2.1.4.1.22
The number of input datagrams discarded due to errors in their IP headers, including bad checksums, version number mismatch, other format errors, time-to-live exceeded, errors discovered in processing their IP options, etc.
Status: mandatory Access: read-only
OBJECT-TYPE    
  Counter  

wfIpInterfaceInAddrErrors 1.3.6.1.4.1.18.3.5.3.2.1.4.1.23
The number of input datagrams discarded because the IP address in their IP header's destination field was not a valid address to be received at this entity. This count includes invalid addresses (e.g., 0.0.0.0) and addresses of unsupported Classes (e.g., Class E). For entities which are not IP Gateways and therefore do not forward datagrams, this counter includes datagrams discarded because the destination address was not a local address.
Status: mandatory Access: read-only
OBJECT-TYPE    
  Counter  

wfIpInterfaceForwDatagrams 1.3.6.1.4.1.18.3.5.3.2.1.4.1.24
The number of input datagrams for which this entity was not their final IP destination, as a result of which an attempt was made to find a route to forward them to that final destination. In entities which do not act as IP Gateways, this counter will include only those packets which were Source-Routed via this entity, and the Source- Route option processing was successful.
Status: mandatory Access: read-only
OBJECT-TYPE    
  Counter  

wfIpInterfaceInUnknownProtos 1.3.6.1.4.1.18.3.5.3.2.1.4.1.25
The number of locally-addressed datagrams received successfully but discarded because of an unknown or unsupported protocol.
Status: mandatory Access: read-only
OBJECT-TYPE    
  Counter  

wfIpInterfaceInDiscards 1.3.6.1.4.1.18.3.5.3.2.1.4.1.26
The number of input IP datagrams for which no problems were encountered to prevent their continued processing, but which were discarded (e.g., for lack of buffer space). Note that this counter does not include any datagrams discarded while awaiting re-assembly.
Status: mandatory Access: read-only
OBJECT-TYPE    
  Counter  

wfIpInterfaceInDelivers 1.3.6.1.4.1.18.3.5.3.2.1.4.1.27
The total number of input datagrams successfully delivered to IP user-protocols (including ICMP).
Status: mandatory Access: read-only
OBJECT-TYPE    
  Counter  

wfIpInterfaceOutRequests 1.3.6.1.4.1.18.3.5.3.2.1.4.1.28
The total number of IP datagrams which local IP user-protocols (including ICMP) supplied to IP in requests for transmission. Note that this counter does not include any datagrams counted in ipForwDatagrams.
Status: mandatory Access: read-only
OBJECT-TYPE    
  Counter  

wfIpInterfaceOutDiscards 1.3.6.1.4.1.18.3.5.3.2.1.4.1.29
The number of output IP datagrams for which no problem was encountered to prevent their transmission to their destination, but which were discarded (e.g., for lack of buffer space). Note that this counter would include datagrams counted in ipForwDatagrams if any such packets met this (discretionary) discard criterion.
Status: mandatory Access: read-only
OBJECT-TYPE    
  Counter  

wfIpInterfaceOutNoRoutes 1.3.6.1.4.1.18.3.5.3.2.1.4.1.30
The number of IP datagrams discarded because no route could be found to transmit them to their destination. Note that this counter includes any packets counted in ipForwDatagrams which meet this `no-route' criterion. Note that this includes any datagarms which a host cannot route because all of its default gateways are down.
Status: mandatory Access: read-only
OBJECT-TYPE    
  Counter  

wfIpInterfaceReasmTimeout 1.3.6.1.4.1.18.3.5.3.2.1.4.1.31
The maximum number of seconds which received fragments are held while they are awaiting reassembly at this entity.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER  

wfIpInterfaceReasmReqds 1.3.6.1.4.1.18.3.5.3.2.1.4.1.32
The number of IP fragments received which needed to be reassembled at this entity.
Status: mandatory Access: read-only
OBJECT-TYPE    
  Counter  

wfIpInterfaceReasmOKs 1.3.6.1.4.1.18.3.5.3.2.1.4.1.33
The number of IP datagrams successfully reassembled.
Status: mandatory Access: read-only
OBJECT-TYPE    
  Counter  

wfIpInterfaceReasmFails 1.3.6.1.4.1.18.3.5.3.2.1.4.1.34
The number of failures detected by the IP re- assembly algorithm (for whatever reason: timed out, errors, etc). Note that this is not necessarily a count of discarded IP fragments since some algorithms (notably the algorithm in RFC 815) can lose track of the number of fragments by combining them as they are received.
Status: mandatory Access: read-only
OBJECT-TYPE    
  Counter  

wfIpInterfaceFragOKs 1.3.6.1.4.1.18.3.5.3.2.1.4.1.35
The number of IP datagrams that have been successfully fragmented at this entity.
Status: mandatory Access: read-only
OBJECT-TYPE    
  Counter  

wfIpInterfaceFragFails 1.3.6.1.4.1.18.3.5.3.2.1.4.1.36
The number of IP datagrams that have been discarded because they needed to be fragmented at this entity but could not be, e.g., because their Don't Fragment flag was set.
Status: mandatory Access: read-only
OBJECT-TYPE    
  Counter  

wfIpInterfaceFragCreates 1.3.6.1.4.1.18.3.5.3.2.1.4.1.37
The number of IP datagram fragments that have been generated as a result of fragmentation at this entity.
Status: mandatory Access: read-only
OBJECT-TYPE    
  Counter  

wfIpInterfaceIcmpInMsgs 1.3.6.1.4.1.18.3.5.3.2.1.4.1.38
The total number of ICMP messages which includes all those counted by wfIpInterfaceIcmpInErrors.
Status: mandatory Access: read-only
OBJECT-TYPE    
  Counter  

wfIpInterfaceIcmpInErrors 1.3.6.1.4.1.18.3.5.3.2.1.4.1.39
The number of ICMP messages which the entity received but determined as having ICMP-specific errors (bad ICMP checksums, bad length, etc.).
Status: mandatory Access: read-only
OBJECT-TYPE    
  Counter  

wfIpInterfaceIcmpInDestUnreachs 1.3.6.1.4.1.18.3.5.3.2.1.4.1.40
The number of ICMP Destination Unreachable messages received.
Status: mandatory Access: read-only
OBJECT-TYPE    
  Counter  

wfIpInterfaceIcmpInTimeExcds 1.3.6.1.4.1.18.3.5.3.2.1.4.1.41
The number of ICMP Time Exceeded messages received.
Status: mandatory Access: read-only
OBJECT-TYPE    
  Counter  

wfIpInterfaceIcmpInParmProbs 1.3.6.1.4.1.18.3.5.3.2.1.4.1.42
The number of ICMP Parameter Problem messages received.
Status: mandatory Access: read-only
OBJECT-TYPE    
  Counter  

wfIpInterfaceIcmpInSrcQuenchs 1.3.6.1.4.1.18.3.5.3.2.1.4.1.43
The number of ICMP Source Quench messages received.
Status: mandatory Access: read-only
OBJECT-TYPE    
  Counter  

wfIpInterfaceIcmpInRedirects 1.3.6.1.4.1.18.3.5.3.2.1.4.1.44
The number of ICMP Redirect messages received.
Status: mandatory Access: read-only
OBJECT-TYPE    
  Counter  

wfIpInterfaceIcmpInEchos 1.3.6.1.4.1.18.3.5.3.2.1.4.1.45
The number of ICMP Echo (request) messages received.
Status: mandatory Access: read-only
OBJECT-TYPE    
  Counter  

wfIpInterfaceIcmpInEchoReps 1.3.6.1.4.1.18.3.5.3.2.1.4.1.46
The number of ICMP Echo Reply messages received.
Status: mandatory Access: read-only
OBJECT-TYPE    
  Counter  

wfIpInterfaceIcmpInTimestamps 1.3.6.1.4.1.18.3.5.3.2.1.4.1.47
The number of ICMP Timestamp (request) messages received.
Status: mandatory Access: read-only
OBJECT-TYPE    
  Counter  

wfIpInterfaceIcmpInTimestampReps 1.3.6.1.4.1.18.3.5.3.2.1.4.1.48
The number of ICMP Timestamp Reply messages received.
Status: mandatory Access: read-only
OBJECT-TYPE    
  Counter  

wfIpInterfaceIcmpInAddrMasks 1.3.6.1.4.1.18.3.5.3.2.1.4.1.49
The number of ICMP Address Mask Request messages received.
Status: mandatory Access: read-only
OBJECT-TYPE    
  Counter  

wfIpInterfaceIcmpInAddrMaskReps 1.3.6.1.4.1.18.3.5.3.2.1.4.1.50
The number of ICMP Address Mask Reply messages received.
Status: mandatory Access: read-only
OBJECT-TYPE    
  Counter  

wfIpInterfaceIcmpOutMsgs 1.3.6.1.4.1.18.3.5.3.2.1.4.1.51
The total number of ICMP messages which this entity attempted to send. Note that this counter includes all those counted by icmpOutErrors.
Status: mandatory Access: read-only
OBJECT-TYPE    
  Counter  

wfIpInterfaceIcmpOutErrors 1.3.6.1.4.1.18.3.5.3.2.1.4.1.52
The number of ICMP messages which this entity did not send due to problems discovered within ICMP such as a lack of buffers. This value should not include errors discovered outside the ICMP layer such as the inability of IP to route the resultant datagram. In some implementations there may be no types of error which contribute to this counter's value.
Status: mandatory Access: read-only
OBJECT-TYPE    
  Counter  

wfIpInterfaceIcmpOutDestUnreachs 1.3.6.1.4.1.18.3.5.3.2.1.4.1.53
The number of ICMP Destination Unreachable messages sent.
Status: mandatory Access: read-only
OBJECT-TYPE    
  Counter  

wfIpInterfaceIcmpOutTimeExcds 1.3.6.1.4.1.18.3.5.3.2.1.4.1.54
The number of ICMP Time Exceeded messages sent.
Status: mandatory Access: read-only
OBJECT-TYPE    
  Counter  

wfIpInterfaceIcmpOutParmProbs 1.3.6.1.4.1.18.3.5.3.2.1.4.1.55
The number of ICMP Parameter Problem messages sent.
Status: mandatory Access: read-only
OBJECT-TYPE    
  Counter  

wfIpInterfaceIcmpOutSrcQuenchs 1.3.6.1.4.1.18.3.5.3.2.1.4.1.56
The number of ICMP Source Quench messages sent.
Status: mandatory Access: read-only
OBJECT-TYPE    
  Counter  

wfIpInterfaceIcmpOutRedirects 1.3.6.1.4.1.18.3.5.3.2.1.4.1.57
The number of ICMP Redirect messages sent. For a host, this object will always be zero, since hosts do not send redirects.
Status: mandatory Access: read-only
OBJECT-TYPE    
  Counter  

wfIpInterfaceIcmpOutEchos 1.3.6.1.4.1.18.3.5.3.2.1.4.1.58
The number of ICMP Echo (request) messages sent.
Status: mandatory Access: read-only
OBJECT-TYPE    
  Counter  

wfIpInterfaceIcmpOutEchoReps 1.3.6.1.4.1.18.3.5.3.2.1.4.1.59
The number of ICMP Echo Reply messages sent.
Status: mandatory Access: read-only
OBJECT-TYPE    
  Counter  

wfIpInterfaceIcmpOutTimestamps 1.3.6.1.4.1.18.3.5.3.2.1.4.1.60
The number of ICMP Timestamp (request) messages sent.
Status: mandatory Access: read-only
OBJECT-TYPE    
  Counter  

wfIpInterfaceIcmpOutTimestampReps 1.3.6.1.4.1.18.3.5.3.2.1.4.1.61
The number of ICMP Timestamp Reply messages sent.
Status: mandatory Access: read-only
OBJECT-TYPE    
  Counter  

wfIpInterfaceIcmpOutAddrMasks 1.3.6.1.4.1.18.3.5.3.2.1.4.1.62
The number of ICMP Address Mask Request messages sent.
Status: mandatory Access: read-only
OBJECT-TYPE    
  Counter  

wfIpInterfaceIcmpOutAddrMaskReps 1.3.6.1.4.1.18.3.5.3.2.1.4.1.63
The number of ICMP Address Mask Reply messages sent.
Status: mandatory Access: read-only
OBJECT-TYPE    
  Counter  

wfIpInterfaceTrEndStation 1.3.6.1.4.1.18.3.5.3.2.1.4.1.64
Use Source Routing over token ring selection. Only applies if pam type is TRING.
Status: mandatory Access: read-write
OBJECT-TYPE    
  INTEGER on(1), off(2)  

wfIpInterfaceSMDSGroupAddress 1.3.6.1.4.1.18.3.5.3.2.1.4.1.65
The SMDS group address
Status: mandatory Access: read-write
OBJECT-TYPE    
  OCTET STRING  

wfIpInterfaceSMDSArpReqAddress 1.3.6.1.4.1.18.3.5.3.2.1.4.1.66
The SMDS arp req address
Status: mandatory Access: read-write
OBJECT-TYPE    
  OCTET STRING  

wfIpInterfaceFRBcastDlci 1.3.6.1.4.1.18.3.5.3.2.1.4.1.67
Frame Relay broadcast dlci
Status: mandatory Access: read-write
OBJECT-TYPE    
  INTEGER  

wfIpInterfaceFRMcast1Dlci 1.3.6.1.4.1.18.3.5.3.2.1.4.1.68
Frame Relay multicast dlci #1
Status: mandatory Access: read-write
OBJECT-TYPE    
  INTEGER  

wfIpInterfaceFRMcast2Dlci 1.3.6.1.4.1.18.3.5.3.2.1.4.1.69
Frame Relay multicast dlci #2
Status: mandatory Access: read-write
OBJECT-TYPE    
  INTEGER  

wfIpInterfaceRedirect 1.3.6.1.4.1.18.3.5.3.2.1.4.1.70
Indicates Whether we're sending out redirects on this Interface or not
Status: mandatory Access: read-write
OBJECT-TYPE    
  INTEGER on(1), off(2)  

wfIpInterfaceEnetArpEncaps 1.3.6.1.4.1.18.3.5.3.2.1.4.1.71
The data link encapsulation type to use for ARP packets if the the media is ethernet.
Status: mandatory Access: read-write
OBJECT-TYPE    
  INTEGER enet(1), snap(2), both(3)  

wfIpStaticRouteTable 1.3.6.1.4.1.18.3.5.3.2.1.5
The list of static routes
Status: mandatory Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    WfIpStaticRouteEntry

wfIpStaticRouteEntry 1.3.6.1.4.1.18.3.5.3.2.1.5.1
A static route definition
Status: mandatory Access: not-accessible
OBJECT-TYPE    
  WfIpStaticRouteEntry  

wfIpSrCreate 1.3.6.1.4.1.18.3.5.3.2.1.5.1.1
Create/Delete parameter. Default is created. Users perform a set operation on this object in order to create/delete the IP Static Route.
Status: mandatory Access: read-write
OBJECT-TYPE    
  INTEGER create(1), delete(2)  

wfIpSrEnable 1.3.6.1.4.1.18.3.5.3.2.1.5.1.2
Enable/Disable parameter. Default is enabled. Users perform a set operation on this object in order to enable/disable this IP Static Route.
Status: mandatory Access: read-write
OBJECT-TYPE    
  INTEGER enable(1), disable(2)  

wfIpSrIpAddress 1.3.6.1.4.1.18.3.5.3.2.1.5.1.3
The Address of this static route
Status: mandatory Access: read-only
OBJECT-TYPE    
  IpAddress  

wfIpSrIpNetMask 1.3.6.1.4.1.18.3.5.3.2.1.5.1.4
The IP Network Mask for this Static Route
Status: mandatory Access: read-only
OBJECT-TYPE    
  IpAddress  

wfIpSrCost 1.3.6.1.4.1.18.3.5.3.2.1.5.1.5
The Cost of this Static Route
Status: mandatory Access: read-write
OBJECT-TYPE    
  INTEGER cost(1)  

wfIpSrNextHopAddr 1.3.6.1.4.1.18.3.5.3.2.1.5.1.6
The Next Hop IP Address
Status: mandatory Access: read-write
OBJECT-TYPE    
  IpAddress  

wfIpSrNextHopMask 1.3.6.1.4.1.18.3.5.3.2.1.5.1.7
The Next Hop IP Netmask
Status: mandatory Access: read-write
OBJECT-TYPE    
  IpAddress  

wfIpSrPreference 1.3.6.1.4.1.18.3.5.3.2.1.5.1.8
This Routes Preference
Status: mandatory Access: read-write
OBJECT-TYPE    
  INTEGER pref(16)  

wfIpSrIpAddressRt 1.3.6.1.4.1.18.3.5.3.2.1.5.1.9
The Route Identifier Which numbered route this is to be
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER  

wfIpSrValid 1.3.6.1.4.1.18.3.5.3.2.1.5.1.10
Whether this Static Route is valid or not
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER valid(1), invalid(2)  

wfIpAdjacentHostTable 1.3.6.1.4.1.18.3.5.3.2.1.6
The list of Adjacent Hosts (static IP-Mac resolutions)
Status: mandatory Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    WfIpAdjacentHostEntry

wfIpAdjacentHostEntry 1.3.6.1.4.1.18.3.5.3.2.1.6.1
A description of an adjacent host
Status: mandatory Access: not-accessible
OBJECT-TYPE    
  WfIpAdjacentHostEntry  

wfIpAdjHostCreate 1.3.6.1.4.1.18.3.5.3.2.1.6.1.1
Whether to Delete this Adjacent Host
Status: mandatory Access: read-write
OBJECT-TYPE    
  INTEGER create(1), delete(2)  

wfIpAdjHostEnable 1.3.6.1.4.1.18.3.5.3.2.1.6.1.2
Whether to Disable this Host
Status: mandatory Access: read-write
OBJECT-TYPE    
  INTEGER enable(1), disable(2)  

wfIpAdjHostIpAddress 1.3.6.1.4.1.18.3.5.3.2.1.6.1.3
The IP address of this Adjacent Host
Status: mandatory Access: read-only
OBJECT-TYPE    
  IpAddress  

wfIpAdjHostIntf 1.3.6.1.4.1.18.3.5.3.2.1.6.1.4
The Interface for this Adjacent Host
Status: mandatory Access: read-write
OBJECT-TYPE    
  IpAddress  

wfIpAdjHostIntfMask 1.3.6.1.4.1.18.3.5.3.2.1.6.1.5
The Network Mask of this Intf
Status: mandatory Access: read-write
OBJECT-TYPE    
  IpAddress  

wfIpAdjHostMacAddr 1.3.6.1.4.1.18.3.5.3.2.1.6.1.6
The LAN Address for this HOST
Status: mandatory Access: read-write
OBJECT-TYPE    
  OCTET STRING  

wfIpAdjHostEncaps 1.3.6.1.4.1.18.3.5.3.2.1.6.1.7
The encapsulation type of this entry
Status: mandatory Access: read-write
OBJECT-TYPE    
  INTEGER enet(1), snap(2)  

wfIpAdjHostValid 1.3.6.1.4.1.18.3.5.3.2.1.6.1.8
Whether the record passed validation or not
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER valid(1), invalid(2)  

wfIpTrafficFilterTable 1.3.6.1.4.1.18.3.5.3.2.1.7
IP Traffic Filters
Status: mandatory Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    WfIpTrafficFilterEntry

wfIpTrafficFilterEntry 1.3.6.1.4.1.18.3.5.3.2.1.7.1
A traffic filter definition
Status: mandatory Access: not-accessible
OBJECT-TYPE    
  WfIpTrafficFilterEntry  

wfIpTrafficFilterCreate 1.3.6.1.4.1.18.3.5.3.2.1.7.1.1
Defines the existence of the traffic filter rule: created - traffic filter exists delete - traffic filter does not exist and can be deleted.
Status: mandatory Access: read-write
OBJECT-TYPE    
  INTEGER created(1), deleted(2)  

wfIpTrafficFilterEnable 1.3.6.1.4.1.18.3.5.3.2.1.7.1.2
Defines whether or not the traffic filter rule should be used: enabled - activate the rule. disabled - inactivate the rule.
Status: mandatory Access: read-write
OBJECT-TYPE    
  INTEGER enabled(1), disabled(2)  

wfIpTrafficFilterStatus 1.3.6.1.4.1.18.3.5.3.2.1.7.1.3
Defines the current status of the traffic filter: inactive - the rule is not in use. active - the rule is being used. error - the application detected an error in the rule.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER active(1), error(2), inactive(3)  

wfIpTrafficFilterCounter 1.3.6.1.4.1.18.3.5.3.2.1.7.1.4
The number of received packets that have matched this rule.
Status: mandatory Access: read-only
OBJECT-TYPE    
  Counter  

wfIpTrafficFilterDefinition 1.3.6.1.4.1.18.3.5.3.2.1.7.1.5
The filter rule definition.
Status: mandatory Access: read-write
OBJECT-TYPE    
  Opaque  

wfIpTrafficFilterReserved 1.3.6.1.4.1.18.3.5.3.2.1.7.1.6
Reserved field.
Status: mandatory Access: not-accessible
OBJECT-TYPE    
  INTEGER  

wfIpTrafficFilterInterface 1.3.6.1.4.1.18.3.5.3.2.1.7.1.7
The network address of the IP interface to which this filter is applied.
Status: mandatory Access: read-only
OBJECT-TYPE    
  IpAddress  

wfIpTrafficFilterCircuit 1.3.6.1.4.1.18.3.5.3.2.1.7.1.8
The ID of the Circuit to which the filter is applied.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER  

wfIpTrafficFilterRuleNumber 1.3.6.1.4.1.18.3.5.3.2.1.7.1.9
ID for the rule.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER  

wfIpTrafficFilterFragment 1.3.6.1.4.1.18.3.5.3.2.1.7.1.10
Fragment number - for large rules.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER  

wfRipIntfTable 1.3.6.1.4.1.18.3.5.3.2.2.1
The list of configured RIP interfaces
Status: mandatory Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    WfRipIntfEntry

wfRipIntfEntry 1.3.6.1.4.1.18.3.5.3.2.2.1.1
A description of a RIP interface
Status: mandatory Access: not-accessible
OBJECT-TYPE    
  WfRipIntfEntry  

wfRipInterfaceCreate 1.3.6.1.4.1.18.3.5.3.2.2.1.1.1
Create/Delete parameter. Default is created. Users perform a set operation on this object in order to create/delete an RIP Interface instance.
Status: mandatory Access: read-write
OBJECT-TYPE    
  INTEGER create(1), delete(2)  

wfRipInterfaceEnable 1.3.6.1.4.1.18.3.5.3.2.2.1.1.2
Enable/Disable parameter. Default is enabled. Users perform a set operation on this object in order to enable/disable a RIP interface.
Status: mandatory Access: read-write
OBJECT-TYPE    
  INTEGER enable(1), disable(2)  

wfRipInterfaceState 1.3.6.1.4.1.18.3.5.3.2.2.1.1.3
The current state of RIP on this interface.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER up(1), down(2), init(3), notpres(4)  

wfRipInterfaceIndex 1.3.6.1.4.1.18.3.5.3.2.2.1.1.4
The IP interface to run RIP on.
Status: mandatory Access: read-only
OBJECT-TYPE    
  IpAddress  

wfRipInterfaceSupply 1.3.6.1.4.1.18.3.5.3.2.2.1.1.5
Transmit RIP packets.
Status: mandatory Access: read-write
OBJECT-TYPE    
  INTEGER enable(1), disable(2)  

wfRipInterfaceListen 1.3.6.1.4.1.18.3.5.3.2.2.1.1.6
Whether to listen to RIP packets
Status: mandatory Access: read-write
OBJECT-TYPE    
  INTEGER enable(1), disable(2)  

wfRipInterfaceDefaultRouteSupply 1.3.6.1.4.1.18.3.5.3.2.2.1.1.7
Transmit the default route, 0.0.0.0, in RIP packets.
Status: mandatory Access: read-write
OBJECT-TYPE    
  INTEGER enable(1), disable(2)  

wfRipInterfaceDefaultRouteListen 1.3.6.1.4.1.18.3.5.3.2.2.1.1.8
Receive the default route, 0.0.0.0, in RIP packets.
Status: mandatory Access: read-write
OBJECT-TYPE    
  INTEGER enable(1), disable(2)  

wfRipInterfacePoisonedReversed 1.3.6.1.4.1.18.3.5.3.2.2.1.1.9
Specifies how the router advertises routes it has learned from a neighboring router in periodic updates subsequently sent to the neighbor. If 'Poisoned', the node implements poisoned reverse. The router now advertises routes learned from a neighbor in RIP updates subsequently sent to that neighbor with a hop count of wfRipBaseRipNetworkDiameter plus 1, (thus declaring the destination unreachable). If 'Split', the router implements a split-horizon, and omits routes learned from a neighbor in RIP updates subsequently sent to that neighbor. If 'Actual', the learned cost of the route is advertised.
Status: mandatory Access: read-write
OBJECT-TYPE    
  INTEGER poisoned(1), actual(2), split(3)  

wfArpBase 1.3.6.1.4.1.18.3.5.3.1.1
OBJECT IDENTIFIER    

wfArpBaseCreate 1.3.6.1.4.1.18.3.5.3.1.1.1
Create/Delete parameter. Default is created. Users perform a set operation on this object in order to create/delete ARP.
Status: mandatory Access: read-write
OBJECT-TYPE    
  INTEGER created(1), deleted(2)  

wfArpBaseEnable 1.3.6.1.4.1.18.3.5.3.1.1.2
Enable/Disable Parameter indicates whether this ARP record is enabled or disabled.
Status: mandatory Access: read-write
OBJECT-TYPE    
  INTEGER enabled(1), disabled(2)  

wfArpBaseForwarding 1.3.6.1.4.1.18.3.5.3.1.1.3
Equivalent to IP Host Only. This attribute says that ARP should send unknown addresses to the bridge for further handling
Status: mandatory Access: read-write
OBJECT-TYPE    
  INTEGER forwarding(1), notforwarding(2)  

wfArpIntfTable 1.3.6.1.4.1.18.3.5.3.1.2
List of configured ARP interfaces
Status: mandatory Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    WfArpIntfEntry

wfArpIntfEntry 1.3.6.1.4.1.18.3.5.3.1.2.1
A description of an ARP interface
Status: mandatory Access: not-accessible
OBJECT-TYPE    
  WfArpIntfEntry  

wfArpCreate 1.3.6.1.4.1.18.3.5.3.1.2.1.1
Indicates whether this ARP intf record is to be deleted or created
Status: mandatory Access: read-write
OBJECT-TYPE    
  INTEGER created(1), deleted(2)  

wfArpEnable 1.3.6.1.4.1.18.3.5.3.1.2.1.2
Indicates whether this ARP intf record is to be enabled or disabled
Status: mandatory Access: read-write
OBJECT-TYPE    
  INTEGER enabled(1), disabled(2)  

wfArpCctno 1.3.6.1.4.1.18.3.5.3.1.2.1.3
Which Circuit arp should run on
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER  

wfIpxBase 1.3.6.1.4.1.18.3.5.5.1
OBJECT IDENTIFIER    

wfIpxBaseDelete 1.3.6.1.4.1.18.3.5.5.1.1
Create/Delete parameter. Default is created. Users perform an SNMP SET operation on this object in order to create/delete IPX.
Status: mandatory Access: read-write
OBJECT-TYPE    
  INTEGER created(1), deleted(2)  

wfIpxBaseDisable 1.3.6.1.4.1.18.3.5.5.1.2
Enable/Disable parameter. Default is enabled. Users perform an SNMP SET operation on this object in order to enable/disable IPX.
Status: mandatory Access: read-write
OBJECT-TYPE    
  INTEGER enabled(1), disabled(2)  

wfIpxBaseState 1.3.6.1.4.1.18.3.5.5.1.3
The current state of the entire IPX.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER up(1), down(2), in(3), notpresent(4)  

wfIpxBaseCfgHostNumber 1.3.6.1.4.1.18.3.5.5.1.4
box generated hostnumber.
Status: mandatory Access: read-write
OBJECT-TYPE    
  OCTET STRING  

wfIpxBaseActiveHostNumber 1.3.6.1.4.1.18.3.5.5.1.5
generated variable.
Status: mandatory Access: read-only
OBJECT-TYPE    
  OCTET STRING  

wfIpxBaseNetCount 1.3.6.1.4.1.18.3.5.5.1.6
Count the total number of nets in the box.
Status: mandatory Access: read-only
OBJECT-TYPE    
  Counter  

wfIpxBaseServiceCount 1.3.6.1.4.1.18.3.5.5.1.7
Count the total number of saps in the box.
Status: mandatory Access: read-only
OBJECT-TYPE    
  Counter  

wfIpxBaseLogFilter 1.3.6.1.4.1.18.3.5.5.1.8
Filter out some log messages, Default filters out debugs, info, and trace messages.
Status: mandatory Access: read-write
OBJECT-TYPE    
  INTEGER debug(1), info(2), trace(16), debuginfo(3), debugtrace(17), infotrace(18), debuginfotrace(19)  

wfIpxBaseNetTblSize 1.3.6.1.4.1.18.3.5.5.1.9
Tell me how much space to set aside when creating the forwarding and network tables.
Status: mandatory Access: read-write
OBJECT-TYPE    
  INTEGER size(250)  

wfIpxBaseRtEntryTable 1.3.6.1.4.1.18.3.5.5.2
The table of Elements in IPX's routing table
Status: mandatory Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    WfIpxBaseRtEntry

wfIpxBaseRtEntry 1.3.6.1.4.1.18.3.5.5.2.1
An entry in the Routing Table
Status: mandatory Access: not-accessible
OBJECT-TYPE    
  WfIpxBaseRtEntry  

wfIpxBaseRouteDest 1.3.6.1.4.1.18.3.5.5.2.1.1
Multiple routes to a single destination can appear in the table, but access to such multiple entries is dependent on the table- access mechanisms defined by the network management protocol in use.
Status: mandatory Access: read-only
OBJECT-TYPE    
  OCTET STRING  

wfIpxBaseRouteIfIndex 1.3.6.1.4.1.18.3.5.5.2.1.2
The index value which uniquely identifies the local interface through which the next hop of this route should be reached. The interface identified by a particular value of this index is the same interface as identified by the same value of ifIndex.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER  

wfIpxBaseRouteMetric 1.3.6.1.4.1.18.3.5.5.2.1.3
The primary routing metric for this route. The semantics of this metric are determined by the routing-protocol specified in the route's ipRouteProto value. If this metric is not used, its value should be set to -1.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER  

wfIpxBaseRouteNextHopNetwork 1.3.6.1.4.1.18.3.5.5.2.1.4
(In the case of a route bound to an interface which is realized via a broadcast media, the value of this field is the agent's IPX address on that interface.)
Status: mandatory Access: read-only
OBJECT-TYPE    
  OCTET STRING  

wfIpxBaseRouteNextHopHost 1.3.6.1.4.1.18.3.5.5.2.1.5
Full network.host_id address of nexthop host for this network.
Status: mandatory Access: read-only
OBJECT-TYPE    
  OCTET STRING  

wfIpxBaseRouteType 1.3.6.1.4.1.18.3.5.5.2.1.6
The type of route. Note that the values direct(3) and indirect(4) refer to the notion of direct and indirect routing in the IPX architecture. Setting this object to the value invalid(2) has the effect of invalidating the corresponding entry in the ipRouteTable object. That is, it effectively dissasociates the destination identified with said entry from the route identified with said entry. It is an implementation-specific matter as to whether the agent removes an invalidated entry from the table. nagement stations must be prepared to receive tabular information from agents that corresponds to entries not currently in use. Proper interpretation of such entries requires examination of the relevant ipRouteType object.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER other(1), invalid(2), direct(3), indirect(4), static(5)  

wfIpxBaseRouteProto 1.3.6.1.4.1.18.3.5.5.2.1.7
The routing mechanism via which this route was learned. Inclusion of values for gateway routing protocols is not intended to imply that hosts should support those protocols.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER other(1), local(2), netmgmt(3), rip(4)  

wfIpxBaseRouteAge 1.3.6.1.4.1.18.3.5.5.2.1.8
The number of seconds since this route was last updated or otherwise determined to be correct. Note that no semantics of `too old' can be implied except through knowledge of the routing protocol by which the route was learned.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER  

wfIpxBaseRouteInfo 1.3.6.1.4.1.18.3.5.5.2.1.9
A user-defined string which describes this Route entry
Status: mandatory Access: read-only
OBJECT-TYPE    
  OCTET STRING  

wfIpxBaseSapEntryTable 1.3.6.1.4.1.18.3.5.5.3
The table of Elements in IPX's SAP table
Status: mandatory Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    WfIpxBaseSapEntry

wfIpxBaseSapEntry 1.3.6.1.4.1.18.3.5.5.3.1
An entry in the Routing Table
Status: mandatory Access: not-accessible
OBJECT-TYPE    
  WfIpxBaseSapEntry  

wfIpxBaseSapType 1.3.6.1.4.1.18.3.5.5.3.1.1
Multiple routes to a single destination can appear in the table, but access to such multiple entries is dependent on the table- access mechanisms defined by the network management protocol in use.
Status: mandatory Access: read-only
OBJECT-TYPE    
  OCTET STRING  

wfIpxBaseSapNetwork 1.3.6.1.4.1.18.3.5.5.3.1.2
The network address of this service.
Status: mandatory Access: read-only
OBJECT-TYPE    
  OCTET STRING  

wfIpxBaseSapHost 1.3.6.1.4.1.18.3.5.5.3.1.3
The host address for this service.
Status: mandatory Access: read-only
OBJECT-TYPE    
  OCTET STRING  

wfIpxBaseSapSocket 1.3.6.1.4.1.18.3.5.5.3.1.4
The socket for this particular service
Status: mandatory Access: read-only
OBJECT-TYPE    
  OCTET STRING  

wfIpxBaseSapName 1.3.6.1.4.1.18.3.5.5.3.1.5
The server name.
Status: mandatory Access: read-only
OBJECT-TYPE    
  DisplayString  

wfIpxBaseSapAge 1.3.6.1.4.1.18.3.5.5.3.1.6
The number of seconds since SAP entry has been updated.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER  

wfIpxBaseSapHops 1.3.6.1.4.1.18.3.5.5.3.1.7
The number of Hops away service is from router.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER  

wfIpxBaseSapIndex 1.3.6.1.4.1.18.3.5.5.3.1.8
Index string comprised of type.network.hostid.socket. Makes sorting easier and its a ah work around.
Status: mandatory Access: read-only
OBJECT-TYPE    
  OCTET STRING  

wfIpxBaseSapIntf 1.3.6.1.4.1.18.3.5.5.3.1.9
Network Address of Nexthop Interface.
Status: mandatory Access: read-only
OBJECT-TYPE    
  OCTET STRING  

wfIpxInterfaceTable 1.3.6.1.4.1.18.3.5.5.4
The network interface record
Status: mandatory Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    WfIpxInterfaceEntry

wfIpxInterfaceEntry 1.3.6.1.4.1.18.3.5.5.4.1
An entry in the Routing Table
Status: mandatory Access: not-accessible
OBJECT-TYPE    
  WfIpxInterfaceEntry  

wfIpxInterfaceIndex 1.3.6.1.4.1.18.3.5.5.4.1.1
A unique value for each IPX interface. Its value ranges between 1 and the value of MAXCIRCUITS.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER  

wfIpxInterfaceDelete 1.3.6.1.4.1.18.3.5.5.4.1.2
Create/Delete parameter. Default is created. Users perform an SNMP SET operation on this object in order to create/delete an IPX interface.
Status: mandatory Access: read-write
OBJECT-TYPE    
  INTEGER created(1), deleted(2)  

wfIpxInterfaceDisable 1.3.6.1.4.1.18.3.5.5.4.1.3
Enable/Disable parameter. Default is enabled. Users perform an SNMP SET operation on this object in order to enable/disable an IPX interface.
Status: mandatory Access: read-write
OBJECT-TYPE    
  INTEGER enabled(1), disabled(2)  

wfIpxInterfaceState 1.3.6.1.4.1.18.3.5.5.4.1.4
The current state of the IPX interface
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER up(1), down(2), init(3), notpresent(4)  

wfIpxInterfaceCircuit 1.3.6.1.4.1.18.3.5.5.4.1.5
The Circuit Number that this interface runs over
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER  

wfIpxInterfaceNetworkNumber 1.3.6.1.4.1.18.3.5.5.4.1.6
The IPX Address to which this entry's addressing information pertains
Status: mandatory Access: read-only
OBJECT-TYPE    
  OCTET STRING  

wfIpxInterfaceCost 1.3.6.1.4.1.18.3.5.5.4.1.7
The Cost associated with the IPX Address of this entry
Status: mandatory Access: read-write
OBJECT-TYPE    
  INTEGER cost(1)  

wfIpxInterfaceXsumOn 1.3.6.1.4.1.18.3.5.5.4.1.8
Flag for checksums
Status: mandatory Access: read-write
OBJECT-TYPE    
  INTEGER enabled(1), disabled(2)  

wfIpxInterfaceCfgEncaps 1.3.6.1.4.1.18.3.5.5.4.1.9
The encapsulation method associated with this interface chosen by the user but not necessarily the one used. (See wfIpxInterfaceEncaps)
Status: mandatory Access: read-write
OBJECT-TYPE    
  INTEGER ethernet(1), lsap(2), novell(3), snap(4)  

wfIpxInterfaceMacAddress 1.3.6.1.4.1.18.3.5.5.4.1.10
The MacAddress of this interface this port will receive or transmit.
Status: mandatory Access: read-only
OBJECT-TYPE    
  OCTET STRING  

wfIpxInterfaceSMDSGroupAddress 1.3.6.1.4.1.18.3.5.5.4.1.11
The SMDS group address
Status: mandatory Access: read-only
OBJECT-TYPE    
  OCTET STRING  

wfIpxInterfaceMaxInfo 1.3.6.1.4.1.18.3.5.5.4.1.12
The maximum size of the INFO (non-MAC) field that this port will receive or transmit.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER  

wfIpxInterfaceInReceives 1.3.6.1.4.1.18.3.5.5.4.1.13
The total number of input datagrams received from interfaces, including those received in error.
Status: mandatory Access: read-only
OBJECT-TYPE    
  Counter  

wfIpxInterfaceInHdrErrors 1.3.6.1.4.1.18.3.5.5.4.1.14
The number of input datagrams discarded due to errors in their IPX headers, including bad checksums, version number mismatch, other format errors, time-to-live exceeded, errors discovered in processing their IPX options, etc.
Status: mandatory Access: read-only
OBJECT-TYPE    
  Counter  

wfIpxInterfaceInAddrErrors 1.3.6.1.4.1.18.3.5.5.4.1.15
The number of input datagrams discarded because the IPX address in their IPX header's destination field was not a valid address to be received at this entity.
Status: mandatory Access: read-only
OBJECT-TYPE    
  Counter  

wfIpxInterfaceForwDatagrams 1.3.6.1.4.1.18.3.5.5.4.1.16
The number of input datagrams for which this entity was not their final IPX destination, as a result of which an attempt was made to find a route to forward them to that final destination. In entities which do not act as IPX Gateways, this counter will include only those packets which were Source-Routed via this entity, and the Source- Route option processing was successful.
Status: mandatory Access: read-only
OBJECT-TYPE    
  Counter  

wfIpxInterfaceInUnknownProtos 1.3.6.1.4.1.18.3.5.5.4.1.17
The number of locally-addressed datagrams received successfully but discarded because of an unknown or unsupported protocol.
Status: mandatory Access: read-only
OBJECT-TYPE    
  Counter  

wfIpxInterfaceInDiscards 1.3.6.1.4.1.18.3.5.5.4.1.18
The number of input IPX datagrams for which no problems were encountered to prevent their continued processing, but which were discarded (e.g., for lack of buffer space). Note that this counter does not include any datagrams discarded while awaiting re-assembly.
Status: mandatory Access: read-only
OBJECT-TYPE    
  Counter  

wfIpxInterfaceInDelivers 1.3.6.1.4.1.18.3.5.5.4.1.19
The total number of input datagrams successfully delivered to IPX user-protocols .
Status: mandatory Access: read-only
OBJECT-TYPE    
  Counter  

wfIpxInterfaceOutRequests 1.3.6.1.4.1.18.3.5.5.4.1.20
The total number of IPX datagrams which local IPX user-protocols supplied to IPX in requests for transmission. Note that this counter does not include any datagrams counted in ipxForwDatagrams.
Status: mandatory Access: read-only
OBJECT-TYPE    
  Counter  

wfIpxInterfaceOutDiscards 1.3.6.1.4.1.18.3.5.5.4.1.21
The number of output IPX datagrams for which no problem was encountered to prevent their transmission to their destination, but which were discarded (e.g., for lack of buffer space). Note that this counter would include datagrams counted in ipForwDatagrams if any such packets met this (discretionary) discard criterion.
Status: mandatory Access: read-only
OBJECT-TYPE    
  Counter  

wfIpxInterfaceOutNoRoutes 1.3.6.1.4.1.18.3.5.5.4.1.22
The number of IPX datagrams discarded because no route could be found to transmit them to their destination. Note that this counter includes any packets counted in ipForwDatagrams which meet this `no-route' criterion. Note that this includes any datagarms which a host cannot route because all of its default gateways are down.
Status: mandatory Access: read-only
OBJECT-TYPE    
  Counter  

wfIpxInterfaceTrEndStation 1.3.6.1.4.1.18.3.5.5.4.1.23
Source Routing flag
Status: mandatory Access: read-write
OBJECT-TYPE    
  INTEGER enabled(1), disabled(2)  

wfIpxInterfaceNetbiosAccept 1.3.6.1.4.1.18.3.5.5.4.1.24
Accept NetBios All Networks Broadcast Packets
Status: mandatory Access: read-write
OBJECT-TYPE    
  INTEGER enabled(1), disabled(2)  

wfIpxInterfaceNetbiosDeliver 1.3.6.1.4.1.18.3.5.5.4.1.25
Deliver NetBios All Networks Broadcast Packets
Status: mandatory Access: read-write
OBJECT-TYPE    
  INTEGER enabled(1), disabled(2)  

wfIpxInterfaceWanSapPeriod 1.3.6.1.4.1.18.3.5.5.4.1.26
Timer for Sap entries over WAN
Status: mandatory Access: read-write
OBJECT-TYPE    
  INTEGER default(1)  

wfIpxInterfaceFRBcast 1.3.6.1.4.1.18.3.5.5.4.1.27
Configurable Frame Relay broadcast address
Status: mandatory Access: read-write
OBJECT-TYPE    
  OCTET STRING  

wfIpxInterfaceFRMcast 1.3.6.1.4.1.18.3.5.5.4.1.28
Configurable Frame Relay multicast address
Status: mandatory Access: read-write
OBJECT-TYPE    
  OCTET STRING  

wfIpxInterfaceEncaps 1.3.6.1.4.1.18.3.5.5.4.1.29
The Active or final encapsulation method associated with this interface as determined by the router's implementation of encapsulation algorithms (rules, restrictions) based on media type.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER ethernet(1), lsap(2), novell(3), snap(4)  

wfIpxInterfaceSplit 1.3.6.1.4.1.18.3.5.5.4.1.30
Comes into to play for non full-meshed WAN networks (Frame Relay)
Status: mandatory Access: read-write
OBJECT-TYPE    
  INTEGER enabled(1), disabled(2)  

wfIpxInterfaceCacheHit 1.3.6.1.4.1.18.3.5.5.4.1.31
Will provide information that will determine the usefullness of caching.
Status: mandatory Access: read-only
OBJECT-TYPE    
  Counter  

wfIpxRipIntfTable 1.3.6.1.4.1.18.3.5.5.5
The list of RIP interfaces
Status: mandatory Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    WfIpxRipIntfEntry

wfIpxRipIntfEntry 1.3.6.1.4.1.18.3.5.5.5.1
An entry in the Routing Table
Status: mandatory Access: not-accessible
OBJECT-TYPE    
  WfIpxRipIntfEntry  

wfIpxRipInterfaceDelete 1.3.6.1.4.1.18.3.5.5.5.1.1
Create/Delete parameter. Default is created. Users perform an SNMP SET operation on this object in order to create/delete an RIP Interface instance.
Status: mandatory Access: read-write
OBJECT-TYPE    
  INTEGER created(1), deleted(2)  

wfIpxRipInterfaceDisable 1.3.6.1.4.1.18.3.5.5.5.1.2
Enable/Disable parameter. Default is enabled. Users perform an SNMP SET operation on this object in order to enable/disable an RIP instance.
Status: mandatory Access: read-write
OBJECT-TYPE    
  INTEGER enabled(1), disabled(2)  

wfIpxRipInterfaceState 1.3.6.1.4.1.18.3.5.5.5.1.3
The current state of RIP on this interface.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER up(1), down(2), init(3), notpresent(4)  

wfIpxRipInterfaceIndex 1.3.6.1.4.1.18.3.5.5.5.1.4
The IPX interface to run RIP on (instance id ).
Status: mandatory Access: read-only
OBJECT-TYPE    
  OCTET STRING  

wfIpxRipInterfaceSupply 1.3.6.1.4.1.18.3.5.5.5.1.5
Transmit RIP packets.
Status: mandatory Access: read-write
OBJECT-TYPE    
  INTEGER enabled(1), disabled(2)  

wfIpxRipInterfaceListen 1.3.6.1.4.1.18.3.5.5.5.1.6
Receive RIP packets.
Status: mandatory Access: read-write
OBJECT-TYPE    
  INTEGER enabled(1), disabled(2)  

wfIpxAdjacentHostTable 1.3.6.1.4.1.18.3.5.5.6
must be configured for a nexthop host.
Status: mandatory Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    WfIpxAdjacentHostEntry

wfIpxAdjacentHostEntry 1.3.6.1.4.1.18.3.5.5.6.1
An entry in the Adjacent Host Table
Status: mandatory Access: not-accessible
OBJECT-TYPE    
  WfIpxAdjacentHostEntry  

wfIpxAhDelete 1.3.6.1.4.1.18.3.5.5.6.1.1
Create/Delete parameter. Default is created. Users perform an SNMP SET operation on this object in order to create/delete the IPX Static Host.
Status: mandatory Access: read-write
OBJECT-TYPE    
  INTEGER created(1), deleted(2)  

wfIpxAhDisable 1.3.6.1.4.1.18.3.5.5.6.1.2
Enable/Disable parameter. Default is enabled. Users perform an SNMP SET operation on this object in order to enable/disable this IPX Static Route.
Status: mandatory Access: read-write
OBJECT-TYPE    
  INTEGER enabled(1), disabled(2)  

wfIpxAhTargHostNetwork 1.3.6.1.4.1.18.3.5.5.6.1.3
The network address of the static host.
Status: mandatory Access: read-only
OBJECT-TYPE    
  OCTET STRING  

wfIpxAhTargHostId 1.3.6.1.4.1.18.3.5.5.6.1.4
The Address of this static host.
Status: mandatory Access: read-only
OBJECT-TYPE    
  OCTET STRING  

wfIpxAhNextHopIntf 1.3.6.1.4.1.18.3.5.5.6.1.5
The Next Hop Interface Network Address
Status: mandatory Access: read-write
OBJECT-TYPE    
  OCTET STRING  

wfIpxAhDlci 1.3.6.1.4.1.18.3.5.5.6.1.6
The next Hop Host address
Status: mandatory Access: read-write
OBJECT-TYPE    
  OCTET STRING  

wfIpxStaticRouteTable 1.3.6.1.4.1.18.3.5.5.7
The list of static routes used for Configuring IPX
Status: mandatory Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    WfIpxStaticRouteEntry

wfIpxStaticRouteEntry 1.3.6.1.4.1.18.3.5.5.7.1
An entry in the Routing Table
Status: mandatory Access: not-accessible
OBJECT-TYPE    
  WfIpxStaticRouteEntry  

wfIpxSrDelete 1.3.6.1.4.1.18.3.5.5.7.1.1
Create/Delete parameter. Default is created. Users perform an SNMP SET operation on this object in order to create/delete the IPX Static Route.
Status: mandatory Access: read-write
OBJECT-TYPE    
  INTEGER created(1), deleted(2)  

wfIpxSrDisable 1.3.6.1.4.1.18.3.5.5.7.1.2
Enable/Disable parameter. Default is enabled. Users perform an SNMP SET operation on this object in order to enable/disable this IPX Static Route.
Status: mandatory Access: read-write
OBJECT-TYPE    
  INTEGER enabled(1), disabled(2)  

wfIpxSrTargNetwork 1.3.6.1.4.1.18.3.5.5.7.1.3
The Address of this static route
Status: mandatory Access: read-only
OBJECT-TYPE    
  OCTET STRING  

wfIpxSrCost 1.3.6.1.4.1.18.3.5.5.7.1.4
The Cost of this Static Route
Status: mandatory Access: read-write
OBJECT-TYPE    
  INTEGER  

wfIpxSrNextHopNetwork 1.3.6.1.4.1.18.3.5.5.7.1.5
The Next Hop IPX Address
Status: mandatory Access: read-only
OBJECT-TYPE    
  OCTET STRING  

wfIpxSrNextHopHost 1.3.6.1.4.1.18.3.5.5.7.1.6
The next Hop Host address
Status: mandatory Access: read-write
OBJECT-TYPE    
  OCTET STRING  

wfIpxSrTargNetworkRt 1.3.6.1.4.1.18.3.5.5.7.1.7
The Route Identifier Which numbered route this is to be
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER  

wfIpxNetBiosStaticRouteTable 1.3.6.1.4.1.18.3.5.5.8
The list of static routes used for Configuring IPX
Status: mandatory Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    WfIpxNetBiosStaticRouteEntry

wfIpxNetBiosStaticRouteEntry 1.3.6.1.4.1.18.3.5.5.8.1
An entry in the Routing Table
Status: mandatory Access: not-accessible
OBJECT-TYPE    
  WfIpxNetBiosStaticRouteEntry  

wfIpxNetBiosSrDelete 1.3.6.1.4.1.18.3.5.5.8.1.1
Create/Delete parameter. Default is created. Users perform an SNMP SET operation on this object in order to create/delete the IPX NETBIOS Static Route.
Status: mandatory Access: read-write
OBJECT-TYPE    
  INTEGER created(1), deleted(2)  

wfIpxNetBiosSrDisable 1.3.6.1.4.1.18.3.5.5.8.1.2
Enable/Disable parameter. Default is enabled. Users perform an SNMP SET operation on this object in order to enable/disable this IPX NETBIOS Static Route.
Status: mandatory Access: read-write
OBJECT-TYPE    
  INTEGER enabled(1), disabled(2)  

wfIpxNetBiosSrTargNetwork 1.3.6.1.4.1.18.3.5.5.8.1.3
The Address of this static route
Status: mandatory Access: read-only
OBJECT-TYPE    
  OCTET STRING  

wfIpxNetBiosSrName 1.3.6.1.4.1.18.3.5.5.8.1.4
The Name of the Target Server
Status: mandatory Access: read-write
OBJECT-TYPE    
  OCTET STRING  

wfIpxNetBiosSrIntf 1.3.6.1.4.1.18.3.5.5.8.1.5
The Interface Identifier for this static entry
Status: mandatory Access: read-only
OBJECT-TYPE    
  OCTET STRING  

wfIpxNetBiosSrIndex 1.3.6.1.4.1.18.3.5.5.8.1.6
The Entry Index Which identifies this is entry
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER  

wfIpxSapNetLvlFilterTable 1.3.6.1.4.1.18.3.5.5.9
The list of Network Level SAP Filters
Status: mandatory Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    WfIpxSapNetLvlFilter

wfIpxSapNetLvlFilter 1.3.6.1.4.1.18.3.5.5.9.1
An entry in the Filter Table
Status: mandatory Access: not-accessible
OBJECT-TYPE    
  WfIpxSapNetLvlFilter  

wfIpxSapNetLvlDelete 1.3.6.1.4.1.18.3.5.5.9.1.1
Create/Delete parameter. Default is created. Users perform an SNMP SET operation on this object in order to create/delete the IPX Sap network level filter.
Status: mandatory Access: read-write
OBJECT-TYPE    
  INTEGER created(1), deleted(2)  

wfIpxSapNetLvlDisable 1.3.6.1.4.1.18.3.5.5.9.1.2
Enable/Disable parameter. Default is enabled. Users perform an SNMP SET operation on this object in order to enable/disable this IPX network level SAP filter.
Status: mandatory Access: read-write
OBJECT-TYPE    
  INTEGER enabled(1), disabled(2)  

wfIpxSapNetLvlTargNetwork 1.3.6.1.4.1.18.3.5.5.9.1.3
The Target Network address to monitor
Status: mandatory Access: read-write
OBJECT-TYPE    
  OCTET STRING  

wfIpxSapNetLvlType 1.3.6.1.4.1.18.3.5.5.9.1.4
The Type of service to monitor
Status: mandatory Access: read-write
OBJECT-TYPE    
  OCTET STRING  

wfIpxSapNetLvlAction 1.3.6.1.4.1.18.3.5.5.9.1.5
The Action to take Advertise or not Advertise
Status: mandatory Access: read-write
OBJECT-TYPE    
  INTEGER active(1), inactive(2)  

wfIpxSapNetLvlIntf 1.3.6.1.4.1.18.3.5.5.9.1.6
The Interface identifier for this filter
Status: mandatory Access: read-only
OBJECT-TYPE    
  OCTET STRING  

wfIpxSapNetLvlIndex 1.3.6.1.4.1.18.3.5.5.9.1.7
The Filter Index .
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER  

wfIpxSapServtLvlFilterTable 1.3.6.1.4.1.18.3.5.5.10
The list of Server Level SAP Filters
Status: mandatory Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    WfIpxSapServLvlFilter

wfIpxSapServLvlFilter 1.3.6.1.4.1.18.3.5.5.10.1
An entry in the Filter Table
Status: mandatory Access: not-accessible
OBJECT-TYPE    
  WfIpxSapServLvlFilter  

wfIpxSapServLvlDelete 1.3.6.1.4.1.18.3.5.5.10.1.1
Create/Delete parameter. Default is created. Users perform an SNMP SET operation on this object in order to create/delete the IPX server-level SAP filter.
Status: mandatory Access: read-write
OBJECT-TYPE    
  INTEGER created(1), deleted(2)  

wfIpxSapServLvlDisable 1.3.6.1.4.1.18.3.5.5.10.1.2
Enable/Disable parameter. Default is enabled. Users perform an SNMP SET operation on this object in order to enable/disable this IPX server-level SAP filter.
Status: mandatory Access: read-write
OBJECT-TYPE    
  INTEGER enabled(1), disabled(2)  

wfIpxSapServLvlTargServer 1.3.6.1.4.1.18.3.5.5.10.1.3
The Server Name to monitor.
Status: mandatory Access: read-write
OBJECT-TYPE    
  DisplayString  

wfIpxSapServLvlType 1.3.6.1.4.1.18.3.5.5.10.1.4
Type of service File server, Printer, etc...
Status: mandatory Access: read-write
OBJECT-TYPE    
  OCTET STRING  

wfIpxSapServLvlAction 1.3.6.1.4.1.18.3.5.5.10.1.5
Associated Action (advertise or ignore )
Status: mandatory Access: read-write
OBJECT-TYPE    
  INTEGER active(1), inactive(2)  

wfIpxSapServLvlIntf 1.3.6.1.4.1.18.3.5.5.10.1.6
The Interface identifier for this filter
Status: mandatory Access: read-only
OBJECT-TYPE    
  OCTET STRING  

wfIpxSapServLvlIndex 1.3.6.1.4.1.18.3.5.5.10.1.7
The Filter Index .
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER  

wfIpxTrafficFilterTable 1.3.6.1.4.1.18.3.5.5.11
IPX Traffic Filters
Status: mandatory Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    WfIpxTrafficFilterEntry

wfIpxTrafficFilterEntry 1.3.6.1.4.1.18.3.5.5.11.1
A traffic filter definition
Status: mandatory Access: not-accessible
OBJECT-TYPE    
  WfIpxTrafficFilterEntry  

wfIpxTrafficFilterCreate 1.3.6.1.4.1.18.3.5.5.11.1.1
Defines the existence of the traffic filter rule: created - traffic filter exists delete - traffic filter does not exist and can be deleted.
Status: mandatory Access: read-write
OBJECT-TYPE    
  INTEGER created(1), deleted(2)  

wfIpxTrafficFilterEnable 1.3.6.1.4.1.18.3.5.5.11.1.2
Defines whether or not the traffic filter rule should be used: enabled - activate the rule. disabled - inactivate the rule.
Status: mandatory Access: read-write
OBJECT-TYPE    
  INTEGER enabled(1), disabled(2)  

wfIpxTrafficFilterStatus 1.3.6.1.4.1.18.3.5.5.11.1.3
Defines the current status of the traffic filter: inactive - the rule is not in use. active - the rule is being used. error - the application detected an error in the rule.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER active(1), error(2), inactive(3)  

wfIpxTrafficFilterCounter 1.3.6.1.4.1.18.3.5.5.11.1.4
The number of received packets that have matched this rule.
Status: mandatory Access: read-only
OBJECT-TYPE    
  Counter  

wfIpxTrafficFilterDefinition 1.3.6.1.4.1.18.3.5.5.11.1.5
The filter rule definition.
Status: mandatory Access: read-write
OBJECT-TYPE    
  Opaque  

wfIpxTrafficFilterReserved 1.3.6.1.4.1.18.3.5.5.11.1.6
Reserved field.
Status: mandatory Access: not-accessible
OBJECT-TYPE    
  INTEGER  

wfIpxTrafficFilterInterface 1.3.6.1.4.1.18.3.5.5.11.1.7
The network address of the IPX interface to which this filter is applied.
Status: mandatory Access: read-only
OBJECT-TYPE    
  OCTET STRING  

wfIpxTrafficFilterCircuit 1.3.6.1.4.1.18.3.5.5.11.1.8
The ID of the Circuit to which the filter is applied.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER  

wfIpxTrafficFilterRuleNumber 1.3.6.1.4.1.18.3.5.5.11.1.9
ID for the rule.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER  

wfIpxTrafficFilterFragment 1.3.6.1.4.1.18.3.5.5.11.1.10
Fragment number - for large rules.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER  

wfProtocols 1.3.6.1.4.1.18.3.2.1
OBJECT IDENTIFIER    

wfIPROTOLoad 1.3.6.1.4.1.18.3.2.1.1
Bit mask for loading the IP routing suite (RIP, EGP, OSPF) on slots 1-14. The MSBit represents slot 1, the next most significant bit represents slot 2, and so forth.
Status: mandatory Access: read-write
OBJECT-TYPE    
  Counter  

wfDECNETLoad 1.3.6.1.4.1.18.3.2.1.2
Bit mask for loading the DECNet router on slots 1-14. The MSBit represents slot 1, the next most significant bit represents slot 2, and so forth.
Status: mandatory Access: read-write
OBJECT-TYPE    
  Counter  

wfATLoad 1.3.6.1.4.1.18.3.2.1.3
Bit mask for loading the AppleTalk router on slots 1-14. The MSBit represents slot 1, the next most significant bit represents slot 2, and so forth.
Status: mandatory Access: read-write
OBJECT-TYPE    
  Counter  

wfXNSLoad 1.3.6.1.4.1.18.3.2.1.4
Bit mask for loading the XNS router on slots 1-14. The MSBit represents slot 1, the next most significant bit represents slot 2, and so forth.
Status: mandatory Access: read-write
OBJECT-TYPE    
  Counter  

wfIPXLoad 1.3.6.1.4.1.18.3.2.1.5
Bit mask for loading the IPX router on slots 1-14. The MSBit represents slot 1, the next most significant bit represents slot 2, and so forth.
Status: mandatory Access: read-write
OBJECT-TYPE    
  Counter  

wfOSILoad 1.3.6.1.4.1.18.3.2.1.6
Bit mask for loading the ISO router on slots 1-14. The MSBit represents slot 1, the next most significant bit represents slot 2, and so forth.
Status: mandatory Access: read-write
OBJECT-TYPE    
  Counter  

wfX25DTELoad 1.3.6.1.4.1.18.3.2.1.7
Bit mask for loading the X.25 DTE protocol on slots 1-14. The MSBit represents slot 1, the next most significant bit represents slot 2, and so forth.
Status: mandatory Access: read-write
OBJECT-TYPE    
  Counter  

wfX25DCELoad 1.3.6.1.4.1.18.3.2.1.8
Bit mask for loading the X.25 DCE protocol on slots 1-14. The MSBit represents slot 1, the next most significant bit represents slot 2, and so forth.
Status: mandatory Access: read-write
OBJECT-TYPE    
  Counter  

wfVINESLoad 1.3.6.1.4.1.18.3.2.1.9
Bit mask for loading the VINES router on slots 1-14. The MSBit represents slot 1, the next most significant bit represents slot 2, and so forth.
Status: mandatory Access: read-write
OBJECT-TYPE    
  Counter  

wfLinkModules 1.3.6.1.4.1.18.3.2.2
OBJECT IDENTIFIER    

wfENETIILoad 1.3.6.1.4.1.18.3.2.2.1
Bit mask for loading the Ethernet II driver on slots 1-14. The MSBit represents slot 1, the next most significant bit represents slot 2, and so forth.
Status: mandatory Access: read-write
OBJECT-TYPE    
  Counter  

wfQENETLoad 1.3.6.1.4.1.18.3.2.2.2
Bit mask for loading the Quad Ethernet driver on slots 1-14. The MSBit represents slot 1, the next most significant bit represents slot 2, and so forth.
Status: mandatory Access: read-write
OBJECT-TYPE    
  Counter  

wfFDDILoad 1.3.6.1.4.1.18.3.2.2.3
Bit mask for loading the FDDI driver on slots 1-14. The MSBit represents slot 1, the next most significant bit represents slot 2 and so forth.
Status: mandatory Access: read-write
OBJECT-TYPE    
  Counter  

wfDSDELoad 1.3.6.1.4.1.18.3.2.2.4
Bit mask for loading the Dual Sync - Dual Enet driver on slots 1-14. The MSBit represents slot 1, the next most significant bit represents slot 2, and so forth.
Status: mandatory Access: read-write
OBJECT-TYPE    
  Counter  

wfDSDEIILoad 1.3.6.1.4.1.18.3.2.2.5
Bit mask for loading the Dual Sync - Dual Enet II driver on slots 1-14. The MSBit represents slot 1, the next most significant bit represents slot 2, and so forth.
Status: mandatory Access: read-write
OBJECT-TYPE    
  Counter  

wfQSYNCLoad 1.3.6.1.4.1.18.3.2.2.6
Bit mask for loading the Quad Sync driver on slots 1-14. The MSBit represents slot 1, the next most significant bit represents slot 2, and so forth.
Status: mandatory Access: read-write
OBJECT-TYPE    
  Counter  

wfDTLoad 1.3.6.1.4.1.18.3.2.2.7
Bit mask for loading the Dual Token driver on slots 1-14. The MSBit represents slot 1, the next most significant bit represents slot 2 and so forth.
Status: mandatory Access: read-write
OBJECT-TYPE    
  Counter  

wfDSTLoad 1.3.6.1.4.1.18.3.2.2.8
Bit mask for loading the DST driver on slots 1-14. The MSBit represents slot 1, the next most significant bit represents slot 2 and so forth.
Status: mandatory Access: read-write
OBJECT-TYPE    
  Counter  

wfT1IILoad 1.3.6.1.4.1.18.3.2.2.9
Bit mask for loading the T1 II driver on slots 1-14. The MSBit represents slot 1, the next most significant bit represents slot 2 and so forth.
Status: mandatory Access: read-write
OBJECT-TYPE    
  Counter  

wfE1IILoad 1.3.6.1.4.1.18.3.2.2.10
Bit mask for loading the E1 II driver on slots 1-14. The MSBit represents slot 1, the next most significant bit represents slot 2 and so forth.
Status: mandatory Access: read-write
OBJECT-TYPE    
  Counter  

wfHSSILoad 1.3.6.1.4.1.18.3.2.2.11
Bit mask for loading the HSSI driver on slots 1-14. The MSBit represents slot 1, the next most significant bit represents slot 2 and so forth.
Status: mandatory Access: read-write
OBJECT-TYPE    
  Counter  

wfFNSDSELoad 1.3.6.1.4.1.18.3.2.2.12
Bit mask for loading the FNSDSE driver on slot 2 (FNES Only). The MSBit represents slot 1, the next most significant bit represents slot 2 and so forth.
Status: mandatory Access: read-write
OBJECT-TYPE    
  Counter  

wfFNSDSDTLoad 1.3.6.1.4.1.18.3.2.2.13
Bit mask for loading the FNSDSDT driver on slot 2 (FNTS Only). The MSBit represents slot 1, the next most significant bit represents slot 2 and so forth.
Status: mandatory Access: read-write
OBJECT-TYPE    
  Counter  

wfDrivers 1.3.6.1.4.1.18.3.2.3
OBJECT IDENTIFIER    

wfLANCELoad 1.3.6.1.4.1.18.3.2.3.1
Bit mask for loading the LANCE chip driver on slots 1-14. The MSBit represents slot 1, the next most significant bit represents slot 2 and so forth.
Status: mandatory Access: read-write
OBJECT-TYPE    
  Counter  

wfILACCLoad 1.3.6.1.4.1.18.3.2.3.2
Bit mask for loading the ILACC chip driver on slots 1-14. The MSBit represents slot 1, the next most significant bit represents slot 2 and so forth.
Status: mandatory Access: read-write
OBJECT-TYPE    
  Counter  

wfFSILoad 1.3.6.1.4.1.18.3.2.3.3
Bit mask for loading the FDDI System Interface (FSI) chip driver on slots 1-14. The MSBit represents slot 1, the next most significant bit represents slot 2 and so forth. This attribute shall be used to configure the FSI chip driver on the appropriate slots for FDDI only (see wfHSSIFSILoad for other usage).
Status: mandatory Access: read-write
OBJECT-TYPE    
  Counter  

wfTMS380Load 1.3.6.1.4.1.18.3.2.3.4
Bit mask for loading the TMS380 chip driver on slots 1-14. The MSBit represents slot 1, the next most significant bit represents slot 2 and so forth.
Status: mandatory Access: read-write
OBJECT-TYPE    
  Counter  

wfMK5025Load 1.3.6.1.4.1.18.3.2.3.5
Bit mask for loading the MK5025 chip driver on slots 1-14. The MSBit represents slot 1, the next most significant bit represents slot 2 and so forth.
Status: mandatory Access: read-write
OBJECT-TYPE    
  Counter  

wfDS2180Load 1.3.6.1.4.1.18.3.2.3.6
Bit mask for loading the DS2180 chip driver on slots 1-14. The MSBit represents slot 1, the next most significant bit represents slot 2 and so forth.
Status: mandatory Access: read-write
OBJECT-TYPE    
  Counter  

wfDS2181Load 1.3.6.1.4.1.18.3.2.3.7
Bit mask for loading the DS2181 chip driver on slots 1-14. The MSBit represents slot 1, the next most significant bit represents slot 2 and so forth.
Status: mandatory Access: read-write
OBJECT-TYPE    
  Counter  

wfDEFALoad 1.3.6.1.4.1.18.3.2.3.8
Bit mask for loading the AM99C10 chip driver on slots 1-14. The MSBit represents slot 1, the next most significant bit represents slot 2 and so forth. The AM99C10 chip is Content Addressable Memory (CAM) and the driver to control it is represented by this attribute. The generic name of this attribute shall be the Hardware Filter Driver which will also provide control of the Dual Ethernet Filter Accelerator (DEFA) chip.
Status: mandatory Access: read-write
OBJECT-TYPE    
  Counter  

wfAMZ8530Load 1.3.6.1.4.1.18.3.2.3.9
Bit mask for loading the AMZ8530 chip driver on slots 1-14. The MSBit represents slot 1, the next most significant bit represents slot 2, and so forth.
Status: mandatory Access: read-write
OBJECT-TYPE    
  Counter  

wfHSSIFSILoad 1.3.6.1.4.1.18.3.2.3.10
Bit mask for loading the HSSI FSI chip driver on slots 1-14. The MSBit represents slot 1, the next most significant bit represents slot 2, and so forth.
Status: mandatory Access: read-write
OBJECT-TYPE    
  Counter  

wfOspfGeneralGroup 1.3.6.1.4.1.18.3.5.3.2.3.1
OBJECT IDENTIFIER    

wfOspfGeneralDelete 1.3.6.1.4.1.18.3.5.3.2.3.1.1
'This value determines whether OSPF is configured'
Status: mandatory Access: read-write
OBJECT-TYPE    
  INTEGER created(1), deleted(2)  

wfOspfGeneralDisable 1.3.6.1.4.1.18.3.5.3.2.3.1.2
'The administrative status of OSPF in the router. The value 'enabled' denotes that the OSPF Process is active on at least one interface; 'disabled' disables it on all interfaces.'
Status: mandatory Access: read-write
OBJECT-TYPE    
  INTEGER enabled(1), disabled(2)  

wfOspfGeneralState 1.3.6.1.4.1.18.3.5.3.2.3.1.3
'The state of OSPF'
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER up(1), down(2), init(3), notpresent(4)  

wfOspfRouterId 1.3.6.1.4.1.18.3.5.3.2.3.1.4
'A 32-bit integer uniquely identifying the router in the Autonomous System. By convention, to ensure uniqueness, this should default to the value of one of the router's IP interface addresses.' REFERENCE 'OSPF Version 2, C.1 Global parameters'
Status: mandatory Access: read-write
OBJECT-TYPE    
  IpAddress  

wfOspfVersionNumber 1.3.6.1.4.1.18.3.5.3.2.3.1.5
'The current version number of the OSPF protocol is 2.' REFERENCE 'OSPF Version 2, Title'
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER  

wfOspfAreaBdrRtrStatus 1.3.6.1.4.1.18.3.5.3.2.3.1.6
'A flag to note whether this router is an area border router.' REFERENCE 'OSPF Version 2, Section 3 Splitting the AS into Areas'
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER true(1), false(2)  

wfOspfASBdrRtrStatus 1.3.6.1.4.1.18.3.5.3.2.3.1.7
'A flag to note whether this router is an Autonomous System border router.' REFERENCE 'OSPF Version 2, Section 3.3 Classification of routers'
Status: mandatory Access: read-write
OBJECT-TYPE    
  INTEGER true(1), false(2)  

wfOspfTOSSupport 1.3.6.1.4.1.18.3.5.3.2.3.1.8
'The router's support for type-of-service routing.' REFERENCE 'OSPF Version 2, Appendix F.1.2 Optional TOS support'
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER true(1), false(2)  

wfOspfSpfHoldDown 1.3.6.1.4.1.18.3.5.3.2.3.1.9
Hold Down Timer for the SPF. The SPF will run at most once per hold down timer value. A value of 0 means no hold down.
Status: mandatory Access: read-write
OBJECT-TYPE    
  INTEGER defval(1), maximum(10)  

wfOspfSlotMask 1.3.6.1.4.1.18.3.5.3.2.3.1.10
Slot mask for which slots OSPF is eligible to run on. The LSBit represents slot 1, the next least significant bit represents slot 2, and so on... Slots can be 1-14.
Status: mandatory Access: read-write
OBJECT-TYPE    
  INTEGER slotmask(16383)  

wfOspfAreaTable 1.3.6.1.4.1.18.3.5.3.2.3.2
-- The OSPF Area Data Structure contains information -- regarding the various areas. The interfaces and -- virtual links are configured as part of these areas. -- Area 0.0.0.0, by definition, is the Backbone Area 'Information describing the configured parameters and cumulative statistics of the router's attached areas.' REFERENCE 'OSPF Version 2, Section 6 The Area Data Structure'
Status: mandatory Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    WfOspfAreaEntry

wfOspfAreaEntry 1.3.6.1.4.1.18.3.5.3.2.3.2.1
'Information describing the configured parameters and cumulative statistics of one of the router's attached areas.'
Status: mandatory Access: not-accessible
OBJECT-TYPE    
  WfOspfAreaEntry  

wfOspfAreaDelete 1.3.6.1.4.1.18.3.5.3.2.3.2.1.1
This value determines if the OSPF router is configured with this area.
Status: mandatory Access: read-write
OBJECT-TYPE    
  INTEGER created(1), deleted(2)  

wfOspfAreaDisable 1.3.6.1.4.1.18.3.5.3.2.3.2.1.2
This value indicates the state of this area on the OSPF router.
Status: mandatory Access: read-write
OBJECT-TYPE    
  INTEGER enabled(1), disabled(2)  

wfOspfAreaState 1.3.6.1.4.1.18.3.5.3.2.3.2.1.3
This value indicates the state of the OSPF Area.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER up(1), down(2)  

wfOspfAreaId 1.3.6.1.4.1.18.3.5.3.2.3.2.1.4
'A 32-bit integer uniquely identifying an area. Area ID 0.0.0.0 is used for the OSPF backbone.' REFERENCE 'OSPF Version 2, Appendix C.2 Area parameters'
Status: mandatory Access: read-only
OBJECT-TYPE    
  IpAddress  

wfOspfAuthType 1.3.6.1.4.1.18.3.5.3.2.3.2.1.5
'The authentication type specified for an area. Additional authentication types may be assigned locally on a per Area basis.' REFERENCE 'OSPF Version 2, Appendix E Authentication' -- none (0), -- simplePassword (1) -- reserved for future specification (2..255) -- reserved for AS specific values (> 255)
Status: mandatory Access: read-write
OBJECT-TYPE    
  INTEGER nopassword(1), simplepassword(2)  

wfOspfImportASExtern 1.3.6.1.4.1.18.3.5.3.2.3.2.1.6
'The area's support for importing AS external link- state advertisements.' REFERENCE 'OSPF Version 2, Appendix C.2 Area parameters'
Status: mandatory Access: read-write
OBJECT-TYPE    
  INTEGER true(1), false(2)  

wfOspfStubMetric 1.3.6.1.4.1.18.3.5.3.2.3.2.1.7
'The metric value applied at the indicated type of service. By default, this equals the least metric at the type of service among the interfaces to other areas.'
Status: mandatory Access: read-write
OBJECT-TYPE    
  INTEGER minimum(1), maximum(16777215)  

wfOspfImportSum 1.3.6.1.4.1.18.3.5.3.2.3.2.1.8
'The area's support for importing Summary advertisements into a stub area. This variable should not be set unless wfOspfImportASExtern is set to FALSE'
Status: mandatory Access: read-write
OBJECT-TYPE    
  INTEGER true(1), false(2)  

wfOspfLsdbTable 1.3.6.1.4.1.18.3.5.3.2.3.3
-- OSPF Link State Database -- The Link State Database contains the Link State -- Advertisements from throughout the areas that the -- device is attached to. 'The OSPF Process's Links State Database.' REFERENCE 'OSPF Version 2, Section 12 Link State Advertisements'
Status: mandatory Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    WfOspfLsdbEntry

wfOspfLsdbEntry 1.3.6.1.4.1.18.3.5.3.2.3.3.1
'A single Link State Advertisement.'
Status: mandatory Access: not-accessible
OBJECT-TYPE    
  WfOspfLsdbEntry  

wfOspfLsdbAreaId 1.3.6.1.4.1.18.3.5.3.2.3.3.1.1
'The 32 bit identifier of the Area from which the LSA was received.' REFERENCE 'OSPF Version 2, Appendix C.2 Area parameters'
Status: mandatory Access: read-only
OBJECT-TYPE    
  IpAddress  

wfOspfLsdbType 1.3.6.1.4.1.18.3.5.3.2.3.3.1.2
'The type of the link state advertisement. Each link state type has a separate advertisement format.' REFERENCE 'OSPF Version 2, Appendix A.4.1 The Link State Advertisement header' stubLink (0), routerLink (1), networkLink (2), summaryLink (3), asSummaryLink (4), asExternalLink (5)
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER routerlink(1), networklink(2), summarylink(3), assummarylink(4), asexternallink(5)  

wfOspfLsdbLSID 1.3.6.1.4.1.18.3.5.3.2.3.3.1.3
'The Link State ID is an LS Type Specific field containing either a Router ID or an IP Address; it identifies the piece of the routing domain that is being described by the advertisement.' REFERENCE 'OSPF Version 2, Section 12.1.4 Link State ID'
Status: mandatory Access: read-only
OBJECT-TYPE    
  IpAddress  

wfOspfLsdbRouterId 1.3.6.1.4.1.18.3.5.3.2.3.3.1.4
'The 32 bit number that uniquely identifies the originating router in the Autonomous System.' REFERENCE 'OSPF Version 2, Appendix C.1 Global parameters'
Status: mandatory Access: read-only
OBJECT-TYPE    
  IpAddress  

wfOspfLsdbSequence 1.3.6.1.4.1.18.3.5.3.2.3.3.1.5
-- Note that the OSPF Sequence Number is a 32 bit signed -- integer. It starts with the value '80000001'h, -- or -'7FFFFFFF'h, and increments until '7FFFFFFF'h -- Thus, a typical sequence number will be very negative. 'The sequence number field is a signed 32-bit integer. It is used to detect old and duplicate link state advertisements. The space of sequence numbers is linearly ordered. The larger the sequence number the more recent the advertisement.' REFERENCE 'OSPF Version 2, Section 12.1.6 LS sequence number'
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER  

wfOspfLsdbAge 1.3.6.1.4.1.18.3.5.3.2.3.3.1.6
'This field is the age of the link state advertisement in seconds.' (OSPF_LSDBMINAGE = 0) REFERENCE 'OSPF Version 2, Section 12.1.1 LS age'
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER lsdbmaxage(3600)  

wfOspfLsdbChecksum 1.3.6.1.4.1.18.3.5.3.2.3.3.1.7
'This field is the checksum of the complete contents of the advertisement, excepting the age field. The age field is excepted so that an advertisement's age can be incremented without updating the checksum. The checksum used is the same that is used for ISO connectionless datagrams; it is commonly referred to as the Fletcher checksum.' REFERENCE 'OSPF Version 2, Section 12.1.7 LS checksum'
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER  

wfOspfLsdbAdvLen 1.3.6.1.4.1.18.3.5.3.2.3.3.1.8
'The length of entire Link State Advertisement, including its header.' REFERENCE 'OSPF Version 2, Section 12 Link State Advertisements'
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER  

wfOspfAreaRangeTable 1.3.6.1.4.1.18.3.5.3.2.3.4
'A range if IP addresses specified by an IP address/IP network mask pair. For example, class B address range of X.X.X.X with a network mask of 255.255.0.0 includes all IP addresses from X.X.0.0 to X.X.255.255' REFERENCE 'OSPF Version 2, Appendix C.2 Area parameters'
Status: mandatory Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    WfOspfAreaRangeEntry

wfOspfAreaRangeEntry 1.3.6.1.4.1.18.3.5.3.2.3.4.1
Status: mandatory Access: not-accessible
OBJECT-TYPE    
  WfOspfAreaRangeEntry  

wfOspfAreaRangeDelete 1.3.6.1.4.1.18.3.5.3.2.3.4.1.1
This value determines if an Area Range has been configured for the OSPF router.
Status: mandatory Access: read-write
OBJECT-TYPE    
  INTEGER created(1), deleted(2)  

wfOspfAreaRangeDisable 1.3.6.1.4.1.18.3.5.3.2.3.4.1.2
'This variable displays the status of the entry. Setting it to 'DISBALED' has the effect of rendering it inoperative. The internal effect (row removal) is implementation dependent.'
Status: mandatory Access: read-write
OBJECT-TYPE    
  INTEGER enabled(1), disabled(2)  

wfOspfAreaRangeState 1.3.6.1.4.1.18.3.5.3.2.3.4.1.3
The state of the OSPF Area Range.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER up(1), down(2)  

wfOspfAreaRangeAreaID 1.3.6.1.4.1.18.3.5.3.2.3.4.1.4
'The Area the Address Range is to be found within.' REFERENCE 'OSPF Version 2, Appendix C.2 Area parameters'
Status: mandatory Access: read-only
OBJECT-TYPE    
  IpAddress  

wfOspfAreaRangeNet 1.3.6.1.4.1.18.3.5.3.2.3.4.1.5
'The IP Address of the Net or Subnet indicated by the range.' REFERENCE 'OSPF Version 2, Appendix C.2 Area parameters'
Status: mandatory Access: read-only
OBJECT-TYPE    
  IpAddress  

wfOspfAreaRangeMask 1.3.6.1.4.1.18.3.5.3.2.3.4.1.6
'The Subnet Mask that pertains to the Net or Subnet.' REFERENCE 'OSPF Version 2, Appendix C.2 Area parameters'
Status: mandatory Access: read-write
OBJECT-TYPE    
  IpAddress  

wfOspfIfTable 1.3.6.1.4.1.18.3.5.3.2.3.5
-- OSPF Interface Table -- The OSPF Interface Table augments the ifTable with OSPF -- specific information. 'The OSPF Interface Table describes the interfaces from the viewpoint of OSPF.' REFERENCE 'OSPF Version 2, Appendix C.3 Router interface parameters'
Status: mandatory Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    WfOspfIfEntry

wfOspfIfEntry 1.3.6.1.4.1.18.3.5.3.2.3.5.1
'The OSPF Interface Entry describes one interface from the viewpoint of OSPF.'
Status: mandatory Access: not-accessible
OBJECT-TYPE    
  WfOspfIfEntry  

wfOspfIfDelete 1.3.6.1.4.1.18.3.5.3.2.3.5.1.1
This variable determines in an OSPF Interface has been configured on the router.
Status: mandatory Access: read-write
OBJECT-TYPE    
  INTEGER created(1), deleted(2)  

wfOspfIfDisable 1.3.6.1.4.1.18.3.5.3.2.3.5.1.2
'The OSPF interface's administrative status. The value 'enabled' denotes that neighbor relationships may be formed on the interface, and the interface will be advertised as an internal route to some area. The value 'disabled' denotes that the interface is external to OSPF.'
Status: mandatory Access: read-write
OBJECT-TYPE    
  INTEGER enabled(1), disabled(2)  

wfOspfIfState 1.3.6.1.4.1.18.3.5.3.2.3.5.1.3
'The OSPF Interface State.' down (1), loopback (2), waiting (3), pointToPoint (4), designatedRouter (5), backupDesignatedRouter (6), otherDesignatedRouter (7)
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER down(1), loopback(2), waiting(3), pointtopoint(4), designatedrouter(5), backupdesignatedrouter(6), otherdesignatedrouter(7)  

wfOspfIfIpAddress 1.3.6.1.4.1.18.3.5.3.2.3.5.1.4
'The IP address of this OSPF interface.'
Status: mandatory Access: read-only
OBJECT-TYPE    
  IpAddress  

wfOspfAddressLessIf 1.3.6.1.4.1.18.3.5.3.2.3.5.1.5
'For the purpose of easing the instancing of addressed and addressless interfaces; This variable takes the value 0 on interfaces with IP Addresses, and the corresponding value of ifIndex for interfaces having no IP Address.'
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER  

wfOspfIfAreaId 1.3.6.1.4.1.18.3.5.3.2.3.5.1.6
'A 32-bit integer uniquely identifying the area to which the interface connects. Area ID 0.0.0.0 is used for the OSPF backbone.' default { '00000000'H } -- 0.0.0.0
Status: mandatory Access: read-write
OBJECT-TYPE    
  IpAddress  

wfOspfIfType 1.3.6.1.4.1.18.3.5.3.2.3.5.1.7
'The OSPF interface type. By way of a default, this field may be intuited from the corresponding value of ifType. Broadcast LANs, such as Ethernet and IEEE 802.5, take the value 'broadcast', X.25, Frame Relay, and similar technologies take the value 'nbma', and links that are definitively point to point take the value 'pointToPoint'.' broadcast (1), nbma (2), pointToPoint (3)
Status: mandatory Access: read-write
OBJECT-TYPE    
  INTEGER broadcast(1), nbma(2), pointtopoint(3)  

wfOspfIfRtrPriority 1.3.6.1.4.1.18.3.5.3.2.3.5.1.8
'The priority of this interface. Used in multi-access networks, this field is used in the designated router election algorithm. The value 0 signifies that the router is not eligible to become the designated router on this particular network. In the event of a tie in this value, routers will use their router id as a tie breaker.'
Status: mandatory Access: read-write
OBJECT-TYPE    
  INTEGER defval(1), maximum(255)  

wfOspfIfTransitDelay 1.3.6.1.4.1.18.3.5.3.2.3.5.1.9
'The estimated number of seconds it takes to transmit a link- state update packet over this interface.'
Status: mandatory Access: read-write
OBJECT-TYPE    
  INTEGER minimum(1), defval(1), maximum(3600)  

wfOspfIfRetransInterval 1.3.6.1.4.1.18.3.5.3.2.3.5.1.10
'The number of seconds between link-state advertisement retransmissions, for adjacencies belonging to this interface. This value is also used when retransmitting database description and link-state request packets.'
Status: mandatory Access: read-write
OBJECT-TYPE    
  INTEGER minimum(1), defval(5), maximum(3600)  

wfOspfIfHelloInterval 1.3.6.1.4.1.18.3.5.3.2.3.5.1.11
'The length of time, in seconds, between the Hello packets that the router sends on the interface. This value must be the same for all routers attached to a common network.'
Status: mandatory Access: read-write
OBJECT-TYPE    
  INTEGER minimum(1), defval(10), maximum(65535)  

wfOspfIfRtrDeadInterval 1.3.6.1.4.1.18.3.5.3.2.3.5.1.12
'The number of seconds that a router's Hello packets have not been seen before it's neighbors declare the router down. This should be some multiple of the Hello interval. This value must be the same for all routers attached to a common network.'
Status: mandatory Access: read-write
OBJECT-TYPE    
  INTEGER minimum(1), defval(40), maximum(2147483647)  

wfOspfIfPollInterval 1.3.6.1.4.1.18.3.5.3.2.3.5.1.13
'The larger time interval, in seconds, between the Hello packets sent to an inactive non-broadcast multi- access neighbor.'
Status: mandatory Access: read-write
OBJECT-TYPE    
  INTEGER minimum(1), defval(120), maximum(2147483647)  

wfOspfIfDesignatedRouter 1.3.6.1.4.1.18.3.5.3.2.3.5.1.14
'The IP Address of the Designated Router.' default { '00000000'H } -- 0.0.0.0
Status: mandatory Access: read-only
OBJECT-TYPE    
  IpAddress  

wfOspfIfBackupDesignatedRouter 1.3.6.1.4.1.18.3.5.3.2.3.5.1.15
'The IP Address of the Backup Designated Router.' default { '00000000'H } -- 0.0.0.0
Status: mandatory Access: read-only
OBJECT-TYPE    
  IpAddress  

wfOspfIfMetricCost 1.3.6.1.4.1.18.3.5.3.2.3.5.1.16
'The cost of using this type of service on this interface. The default value of the TOS 0 Metric is 10^8 / ifSpeed. The value FFFF is distinguished to mean 'no route via this TOS'.'
Status: mandatory Access: read-write
OBJECT-TYPE    
  INTEGER minimum(1), maximum(65535)  

wfOspfIfAuthKey 1.3.6.1.4.1.18.3.5.3.2.3.5.1.17
'The Authentication Key. If the Area's Authorization Type is simplePassword, and the key length is shorter than 8 octets, the agent will left adjust and zero fill to 8 octets. When read, ospfIfAuthKey always returns an Octet String of length zero.' default { '0000000000000000'H } -- 0.0.0.0.0.0.0.0 REFERENCE 'OSPF Version 2, Section 9 The Interface Data Structure'
Status: mandatory Access: read-write
OBJECT-TYPE    
  OCTET STRING  

wfOspfIfTxHellos 1.3.6.1.4.1.18.3.5.3.2.3.5.1.18
Number of OSPF Hello packets transmitted.
Status: mandatory Access: read-only
OBJECT-TYPE    
  Counter  

wfOspfIfTxDBDescripts 1.3.6.1.4.1.18.3.5.3.2.3.5.1.19
Number of OSPF DataBase Description packets transmitted.
Status: mandatory Access: read-only
OBJECT-TYPE    
  Counter  

wfOspfIfTxLinkStateReqs 1.3.6.1.4.1.18.3.5.3.2.3.5.1.20
Number of OSPF Link State Request packets transmitted.
Status: mandatory Access: read-only
OBJECT-TYPE    
  Counter  

wfOspfIfTxLinkStateUpds 1.3.6.1.4.1.18.3.5.3.2.3.5.1.21
Number of OSPF Link State Update packets transmitted.
Status: mandatory Access: read-only
OBJECT-TYPE    
  Counter  

wfOspfIfTxLinkStateAcks 1.3.6.1.4.1.18.3.5.3.2.3.5.1.22
Number of OSPF Link States Acknowledgements transmitted.
Status: mandatory Access: read-only
OBJECT-TYPE    
  Counter  

wfOspfIfRxHellos 1.3.6.1.4.1.18.3.5.3.2.3.5.1.23
Number of OSPF Hello packets received.
Status: mandatory Access: read-only
OBJECT-TYPE    
  Counter  

wfOspfIfRxDBDescripts 1.3.6.1.4.1.18.3.5.3.2.3.5.1.24
Number of OSPF DataBase Description packets received.
Status: mandatory Access: read-only
OBJECT-TYPE    
  Counter  

wfOspfIfRxLinkStateReqs 1.3.6.1.4.1.18.3.5.3.2.3.5.1.25
Number of OSPF Link State Requests received.
Status: mandatory Access: read-only
OBJECT-TYPE    
  Counter  

wfOspfIfRxLinkStateUpds 1.3.6.1.4.1.18.3.5.3.2.3.5.1.26
Number of OSPF Link State Updates received.
Status: mandatory Access: read-only
OBJECT-TYPE    
  Counter  

wfOspfIfRxLinkStateAcks 1.3.6.1.4.1.18.3.5.3.2.3.5.1.27
Number of OSPF Link State Acknowledgements received.
Status: mandatory Access: read-only
OBJECT-TYPE    
  Counter  

wfOspfIfDrops 1.3.6.1.4.1.18.3.5.3.2.3.5.1.28
Number of OSPF packets dropped because of invalid information in the packet.
Status: mandatory Access: read-only
OBJECT-TYPE    
  Counter  

wfOspfVirtIfTable 1.3.6.1.4.1.18.3.5.3.2.3.6
-- OSPF Virtual Interface Table -- The Virtual Interface Table describes the virtual -- links that the OSPF Process is configured to -- carry on. 'Information about this router's virtual interfaces.' REFERENCE 'OSPF Version 2, Appendix C.4 Virtual link parameters'
Status: mandatory Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    WfOspfVirtIfEntry

wfOspfVirtIfEntry 1.3.6.1.4.1.18.3.5.3.2.3.6.1
'Information about a single Virtual Interface.'
Status: mandatory Access: not-accessible
OBJECT-TYPE    
  WfOspfVirtIfEntry  

wfOspfVirtIfDelete 1.3.6.1.4.1.18.3.5.3.2.3.6.1.1
Status: mandatory Access: read-write
OBJECT-TYPE    
  INTEGER created(1), deleted(2)  

wfOspfVirtIfDisable 1.3.6.1.4.1.18.3.5.3.2.3.6.1.2
'This variable displays the validity or invalidity of the entry. Setting it to 'invalid' has the effect of rendering it inoperative. The internal effect (row removal) is implementation dependent.'
Status: mandatory Access: read-write
OBJECT-TYPE    
  INTEGER enabled(1), disabled(2)  

wfOspfVirtIfState 1.3.6.1.4.1.18.3.5.3.2.3.6.1.3
'OSPF virtual interface states.' down (1), -- these use the same encoding pointToPoint (4) -- as the ospfIfTable
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER down(1), pointtopoint(4)  

wfOspfVirtIfAreaID 1.3.6.1.4.1.18.3.5.3.2.3.6.1.4
'The Transit Area that the Virtual Link traverses. By definition, this is not 0.0.0.0'
Status: mandatory Access: read-only
OBJECT-TYPE    
  IpAddress  

wfOspfVirtIfNeighbor 1.3.6.1.4.1.18.3.5.3.2.3.6.1.5
'The Router ID of the Virtual Neighbor.'
Status: mandatory Access: read-only
OBJECT-TYPE    
  IpAddress  

wfOspfVirtIfTransitDelay 1.3.6.1.4.1.18.3.5.3.2.3.6.1.6
'The estimated number of seconds it takes to transmit a link- state update packet over this interface.'
Status: mandatory Access: read-write
OBJECT-TYPE    
  INTEGER minimum(1), defval(1), maximum(3600)  

wfOspfVirtIfRetransInterval 1.3.6.1.4.1.18.3.5.3.2.3.6.1.7
'The number of seconds between link-state advertisement retransmissions, for adjacencies belonging to this interface. This value is also used when retransmitting database description and link-state request packets. This value should be well over the expected round-trip time.'
Status: mandatory Access: read-write
OBJECT-TYPE    
  INTEGER minimum(1), defval(5), maximum(3600)  

wfOspfVirtIfHelloInterval 1.3.6.1.4.1.18.3.5.3.2.3.6.1.8
'The length of time, in seconds, between the Hello packets that the router sends on the interface. This value must be the same for the virtual neighbor.'
Status: mandatory Access: read-write
OBJECT-TYPE    
  INTEGER minimum(1), defval(15), maximum(65535)  

wfOspfVirtIfRtrDeadInterval 1.3.6.1.4.1.18.3.5.3.2.3.6.1.9
'The number of seconds that a router's Hello packets have not been seen before it's neighbors declare the router down. This should be some multiple of the Hello interval. This value must be the same for the virtual neighbor.'
Status: mandatory Access: read-write
OBJECT-TYPE    
  INTEGER minimum(1), defval(60), maximum(2147483647)  

wfOspfVirtIfAuthKey 1.3.6.1.4.1.18.3.5.3.2.3.6.1.10
'If Authentication Type is simplePassword, the device will left adjust and zero fill to 8 octets. When read, ospfVifAuthKey always returns a string of length zero.' REFERENCE 'OSPF Version 2, Section 9 The Interface Data Structure'
Status: mandatory Access: read-write
OBJECT-TYPE    
  OCTET STRING  

wfOspfVirtIfTxHellos 1.3.6.1.4.1.18.3.5.3.2.3.6.1.11
Number of OSPF Hello packets transmitted on Virtual Interfaces.
Status: mandatory Access: read-only
OBJECT-TYPE    
  Counter  

wfOspfVirtIfTxDBDescripts 1.3.6.1.4.1.18.3.5.3.2.3.6.1.12
Number of OSPF DataBase Description packets transmitted on Virtual Interfaces.
Status: mandatory Access: read-only
OBJECT-TYPE    
  Counter  

wfOspfVirtIfTxLinkStateReqs 1.3.6.1.4.1.18.3.5.3.2.3.6.1.13
Number of OSPF Link State Request packets transmitted on Virtual Interfaces.
Status: mandatory Access: read-only
OBJECT-TYPE    
  Counter  

wfOspfVirtIfTxLinkStateUpds 1.3.6.1.4.1.18.3.5.3.2.3.6.1.14
Number of OSPF Link State Update packets transmitted on Virtual Interfaces.
Status: mandatory Access: read-only
OBJECT-TYPE    
  Counter  

wfOspfVirtIfTxLinkStateAcks 1.3.6.1.4.1.18.3.5.3.2.3.6.1.15
Number of OSPF Link State Acknowledgement packets transmitted on Virtual Interfaces.
Status: mandatory Access: read-only
OBJECT-TYPE    
  Counter  

wfOspfVirtIfRxHellos 1.3.6.1.4.1.18.3.5.3.2.3.6.1.16
Number of OSPF Hello packets received on Virtual Interfaces.
Status: mandatory Access: read-only
OBJECT-TYPE    
  Counter  

wfOspfVirtIfRxDBDescripts 1.3.6.1.4.1.18.3.5.3.2.3.6.1.17
Number of OSPF DataBase Description packets received on Virtual Interfaces.
Status: mandatory Access: read-only
OBJECT-TYPE    
  Counter  

wfOspfVirtIfRxLinkStateReqs 1.3.6.1.4.1.18.3.5.3.2.3.6.1.18
Number of OSPF Link State Request packets recieved on Virtual Interfaces.
Status: mandatory Access: read-only
OBJECT-TYPE    
  Counter  

wfOspfVirtIfRxLinkStateUpds 1.3.6.1.4.1.18.3.5.3.2.3.6.1.19
Number of OSPF Link State Update packets received on Virtual Interfaces.
Status: mandatory Access: read-only
OBJECT-TYPE    
  Counter  

wfOspfVirtIfRxLinkStateAcks 1.3.6.1.4.1.18.3.5.3.2.3.6.1.20
Number of OSPF Link State Acknowledgement packets received on Virtual Interfaces.
Status: mandatory Access: read-only
OBJECT-TYPE    
  Counter  

wfOspfVirtIfDrops 1.3.6.1.4.1.18.3.5.3.2.3.6.1.21
Number of OSPF packets dropped on Virtual Interfaces.
Status: mandatory Access: read-only
OBJECT-TYPE    
  Counter  

wfOspfNbrTable 1.3.6.1.4.1.18.3.5.3.2.3.7
-- OSPF Neighbor Table -- The OSPF Neighbor Table describes all neighbors in -- the locality of the subject router. 'A table of non-virtual neighbor information.' REFERENCE 'OSPF Version 2, Section 10 The Neighbor Data Structure'
Status: mandatory Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    WfOspfNbrEntry

wfOspfNbrEntry 1.3.6.1.4.1.18.3.5.3.2.3.7.1
'The information regarding a single neighbor.' REFERENCE 'OSPF Version 2, Section 10 The Neighbor Data Structure'
Status: mandatory Access: not-accessible
OBJECT-TYPE    
  WfOspfNbrEntry  

wfOspfNbrDelete 1.3.6.1.4.1.18.3.5.3.2.3.7.1.1
This variable indicates the existence of a static OSPF neighbor.
Status: mandatory Access: read-write
OBJECT-TYPE    
  INTEGER created(1), deleted(2)  

wfOspfNbrDisable 1.3.6.1.4.1.18.3.5.3.2.3.7.1.2
'This variable displays the status of the entry. Setting it to 'DISABLED' has the effect of rendering it inoperative. The internal effect (row removal) is implementation dependent.'
Status: mandatory Access: read-write
OBJECT-TYPE    
  INTEGER enabled(1), disabled(2)  

wfOspfNbrState 1.3.6.1.4.1.18.3.5.3.2.3.7.1.3
'The State of the relationship with this Neighbor.' REFERENCE 'OSPF Version 2, Section 10.1 Neighbor States' down (1), attempt (2), init (3), twoWay (4), exchangeStart (5), exchange (6), loading (7), full (8)
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER down(1), attempt(2), init(3), twoway(4), exchangstart(5), exchange(6), loading(7), full(8)  

wfOspfNbrIpAddr 1.3.6.1.4.1.18.3.5.3.2.3.7.1.4
'The IP address of this neighbor.'
Status: mandatory Access: read-only
OBJECT-TYPE    
  IpAddress  

wfOspfNbrIfAddr 1.3.6.1.4.1.18.3.5.3.2.3.7.1.5
'The Interface IP address for this neighbor.'
Status: mandatory Access: read-write
OBJECT-TYPE    
  IpAddress  

wfOspfNbrAddressLessIndex 1.3.6.1.4.1.18.3.5.3.2.3.7.1.6
' On an interface having an IP Address, zero. On addressless interfaces, the corresponding value of ifIndex in the Internet Standard MIB. On row creation, this can be derived from the instance.'
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER  

wfOspfNbrRtrId 1.3.6.1.4.1.18.3.5.3.2.3.7.1.7
'A 32-bit integer (represented as a type IpAddress) uniquely identifying the neighboring router in the Autonomous System.' default { '00000000'H } -- 0.0.0.0
Status: mandatory Access: read-only
OBJECT-TYPE    
  IpAddress  

wfOspfNbrOptions 1.3.6.1.4.1.18.3.5.3.2.3.7.1.8
'A Bit Mask corresponding to the neighbor's options field. Bit 0, if set, indicates that the area accepts and operates on external information; if zero, it is a stub area. Bit 1, if set, indicates that the system will operate on Type of Service metrics other than TOS 0. If zero, the neighbor will ignore all metrics except the TOS 0 metric.' REFERENCE 'OSPF Version 2, Section 12.1.2 Options'
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER  

wfOspfNbrPriority 1.3.6.1.4.1.18.3.5.3.2.3.7.1.9
'The priority of this neighbor in the designated router election algorithm. The value 0 signifies that the neighbor is not eligible to become the designated router on this particular network.'
Status: mandatory Access: read-write
OBJECT-TYPE    
  INTEGER defval(1), maximum(255)  

wfOspfNbrEvents 1.3.6.1.4.1.18.3.5.3.2.3.7.1.10
'The number of times this neighbor relationship has changed state, or an error has occurred.'
Status: mandatory Access: read-only
OBJECT-TYPE    
  Counter  

wfOspfNbrLSRetransQLen 1.3.6.1.4.1.18.3.5.3.2.3.7.1.11
'The current length of the retransmission queue.'
Status: mandatory Access: read-only
OBJECT-TYPE    
  Gauge  

wfOspfVirtNbrTable 1.3.6.1.4.1.18.3.5.3.2.3.8
-- WFOSPF Virtual Neighbor Table -- This table describes all virtual neighbors. -- Since Virtual Links are configured in the -- virtual interface table, this table is read-only. 'A table of virtual neighbor information.' REFERENCE 'OSPF Version 2, '
Status: mandatory Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    WfOspfVirtNbrEntry

wfOspfVirtNbrEntry 1.3.6.1.4.1.18.3.5.3.2.3.8.1
'Virtual neighbor information.' REFERENCE 'OSPF Version 2, '
Status: mandatory Access: not-accessible
OBJECT-TYPE    
  WfOspfVirtNbrEntry  

wfOspfVirtNbrArea 1.3.6.1.4.1.18.3.5.3.2.3.8.1.1
'The Transit Area Identifier.'
Status: mandatory Access: read-only
OBJECT-TYPE    
  IpAddress  

wfOspfVirtNbrRtrId 1.3.6.1.4.1.18.3.5.3.2.3.8.1.2
'A 32-bit integer uniquely identifying the neighboring router in the Autonomous System.'
Status: mandatory Access: read-only
OBJECT-TYPE    
  IpAddress  

wfOspfVirtNbrIpAddr 1.3.6.1.4.1.18.3.5.3.2.3.8.1.3
'The IP address this Virtual Neighbor is using.'
Status: mandatory Access: read-only
OBJECT-TYPE    
  IpAddress  

wfOspfVirtNbrOptions 1.3.6.1.4.1.18.3.5.3.2.3.8.1.4
'A bit map corresponding to the neighbor's options field. Thus, Bit 1, if set, indicates that the neighbor supports Type of Service Routing; if zero, no metrics other than TOS 0 are in use by the neighbor.'
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER  

wfOspfVirtNbrState 1.3.6.1.4.1.18.3.5.3.2.3.8.1.5
'The state of the Virtual Neighbor Relationship.' down (1), attempt (2), init (3), twoWay (4), exchangeStart (5), exchange (6), loading (7), full (8)
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER down(1), attempt(2), init(3), twoway(4), exchangstart(5), exchange(6), loading(7), full(8)  

wfOspfVirtNbrEvents 1.3.6.1.4.1.18.3.5.3.2.3.8.1.6
'The number of times this virtual link has changed its state, or an error has occurred.'
Status: mandatory Access: read-only
OBJECT-TYPE    
  Counter  

wfOspfVirtNbrLSRetransQLen 1.3.6.1.4.1.18.3.5.3.2.3.8.1.7
'The current length of the retransmission queue.'
Status: mandatory Access: read-only
OBJECT-TYPE    
  Gauge  

wfOspfDynNbrTable 1.3.6.1.4.1.18.3.5.3.2.3.9
-- OSPF Dynamic Neighbor Table -- The OSPF Dynamic Neighbor Table describes all neighbors in -- the locality of the subject router learned during operation. 'A table of non-virtual neighbor information.' REFERENCE 'OSPF Version 2, Section 10 The Neighbor Data Structure'
Status: mandatory Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    WfOspfDynNbrEntry

wfOspfDynNbrEntry 1.3.6.1.4.1.18.3.5.3.2.3.9.1
'The information regarding a single neighbor.' REFERENCE 'OSPF Version 2, Section 10 The Neighbor Data Structure'
Status: mandatory Access: not-accessible
OBJECT-TYPE    
  WfOspfDynNbrEntry  

wfOspfDynNbrState 1.3.6.1.4.1.18.3.5.3.2.3.9.1.1
'The State of the relationship with this Neighbor.' REFERENCE 'OSPF Version 2, Section 10.1 Neighbor States' down (1), attempt (2), init (3), twoWay (4), exchangeStart (5), exchange (6), loading (7), full (8)
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER down(1), attempt(2), init(3), twoway(4), exchangstart(5), exchange(6), loading(7), full(8)  

wfOspfDynNbrIpAddr 1.3.6.1.4.1.18.3.5.3.2.3.9.1.2
'The IP address of this neighbor.'
Status: mandatory Access: read-only
OBJECT-TYPE    
  IpAddress  

wfOspfDynNbrIfAddr 1.3.6.1.4.1.18.3.5.3.2.3.9.1.3
'The Interface IP address for this neighbor.'
Status: mandatory Access: read-only
OBJECT-TYPE    
  IpAddress  

wfOspfDynNbrAddressLessIndex 1.3.6.1.4.1.18.3.5.3.2.3.9.1.4
' On an interface having an IP Address, zero. On addressless interfaces, the corresponding value of ifIndex in the Internet Standard MIB. On row creation, this can be derived from the instance.'
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER  

wfOspfDynNbrRtrId 1.3.6.1.4.1.18.3.5.3.2.3.9.1.5
'A 32-bit integer (represented as a type IpAddress) uniquely identifying the neighboring router in the Autonomous System.' default { '00000000'H } -- 0.0.0.0
Status: mandatory Access: read-only
OBJECT-TYPE    
  IpAddress  

wfOspfDynNbrOptions 1.3.6.1.4.1.18.3.5.3.2.3.9.1.6
'A Bit Mask corresponding to the neighbor's options field. Bit 0, if set, indicates that the area accepts and operates on external information; if zero, it is a stub area. Bit 1, if set, indicates that the system will operate on Type of Service metrics other than TOS 0. If zero, the neighbor will ignore all metrics except the TOS 0 metric.' REFERENCE 'OSPF Version 2, Section 12.1.2 Options'
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER  

wfOspfDynNbrPriority 1.3.6.1.4.1.18.3.5.3.2.3.9.1.7
'The priority of this neighbor in the designated router election algorithm. The value 0 signifies that the neighbor is not eligible to become the designated router on this particular network.'
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER  

wfOspfDynNbrEvents 1.3.6.1.4.1.18.3.5.3.2.3.9.1.8
'The number of times this neighbor relationship has changed state, or an error has occurred.'
Status: mandatory Access: read-only
OBJECT-TYPE    
  Counter  

wfOspfDynNbrLSRetransQLen 1.3.6.1.4.1.18.3.5.3.2.3.9.1.9
'The current length of the retransmission queue.'
Status: mandatory Access: read-only
OBJECT-TYPE    
  Gauge  

wfIpRfRipImportTable 1.3.6.1.4.1.18.3.5.3.2.1.8
The list of Rip Import Route Filter Rules in IP
Status: mandatory Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    WfIpRfRipImportEntry

wfIpRfRipImportEntry 1.3.6.1.4.1.18.3.5.3.2.1.8.1
An entry in the Rip Import Rule Table
Status: mandatory Access: not-accessible
OBJECT-TYPE    
  WfIpRfRipImportEntry  

wfIpRfRipImportCreate 1.3.6.1.4.1.18.3.5.3.2.1.8.1.1
Create/Delete parameter. Default is created. Users perform an SNMP SET operation on this object in order to create/delete this Rule.
Status: mandatory Access: read-write
OBJECT-TYPE    
  INTEGER create(1), delete(2)  

wfIpRfRipImportEnable 1.3.6.1.4.1.18.3.5.3.2.1.8.1.2
Enable/Disable parameter. Default is enabled. Users perform an SNMP SET operation on this object in order to enable/disable this Rule.
Status: mandatory Access: read-write
OBJECT-TYPE    
  INTEGER enable(1), disable(2)  

wfIpRfRipImportAddress 1.3.6.1.4.1.18.3.5.3.2.1.8.1.3
The IP address to which this filter applies
Status: mandatory Access: read-only
OBJECT-TYPE    
  IpAddress  

wfIpRfRipImportMask 1.3.6.1.4.1.18.3.5.3.2.1.8.1.4
The Mask to which this filter applies. When combined with the Address, a range is specified for application of this rule
Status: mandatory Access: read-only
OBJECT-TYPE    
  IpAddress  

wfIpRfRipImportAction 1.3.6.1.4.1.18.3.5.3.2.1.8.1.5
The Action of this Filter
Status: mandatory Access: read-write
OBJECT-TYPE    
  INTEGER accept(1), ignore(3)  

wfIpRfRipImportPreference 1.3.6.1.4.1.18.3.5.3.2.1.8.1.6
The Preference associated with this filter - only valid if accept
Status: mandatory Access: read-write
OBJECT-TYPE    
  INTEGER maximum(16)  

wfIpRfRipImportRipGateway 1.3.6.1.4.1.18.3.5.3.2.1.8.1.7
The RIP Gateway to be concerned with
Status: mandatory Access: read-only
OBJECT-TYPE    
  IpAddress  

wfIpRfRipImportRipInterface 1.3.6.1.4.1.18.3.5.3.2.1.8.1.8
The IP Network Interface to be concerned with
Status: mandatory Access: read-only
OBJECT-TYPE    
  IpAddress  

wfIpRfRipExportTable 1.3.6.1.4.1.18.3.5.3.2.1.9
The list of Rip Export Route Filter Rules in IP
Status: mandatory Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    WfIpRfRipExportEntry

wfIpRfRipExportEntry 1.3.6.1.4.1.18.3.5.3.2.1.9.1
An entry in the Rip Export Rule Table
Status: mandatory Access: not-accessible
OBJECT-TYPE    
  WfIpRfRipExportEntry  

wfIpRfRipExportCreate 1.3.6.1.4.1.18.3.5.3.2.1.9.1.1
Create/Delete parameter. Default is created. Users perform an SNMP SET operation on this object in order to create/delete this Rule.
Status: mandatory Access: read-write
OBJECT-TYPE    
  INTEGER create(1), delete(2)  

wfIpRfRipExportEnable 1.3.6.1.4.1.18.3.5.3.2.1.9.1.2
Enable/Disable parameter. Default is enabled. Users perform an SNMP SET operation on this object in order to enable/disable this Rule.
Status: mandatory Access: read-write
OBJECT-TYPE    
  INTEGER enable(1), disable(2)  

wfIpRfRipExportAddress 1.3.6.1.4.1.18.3.5.3.2.1.9.1.3
The IP address to which this filter applies
Status: mandatory Access: read-only
OBJECT-TYPE    
  IpAddress  

wfIpRfRipExportMask 1.3.6.1.4.1.18.3.5.3.2.1.9.1.4
The Mask for the Address Above. When combined with the Address, a range is specified for application of this filter rule
Status: mandatory Access: read-only
OBJECT-TYPE    
  IpAddress  

wfIpRfRipExportFromProtocol 1.3.6.1.4.1.18.3.5.3.2.1.9.1.5
The protocol from which this Information is derived
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER rip(1), ospf(3), direct(4), static(5)  

wfIpRfRipExportAction 1.3.6.1.4.1.18.3.5.3.2.1.9.1.6
The action of this export filter
Status: mandatory Access: read-write
OBJECT-TYPE    
  INTEGER propa(2), ignore(3)  

wfIpRfRipExportInterface 1.3.6.1.4.1.18.3.5.3.2.1.9.1.7
The optional outbound interface on which to apply this filter
Status: mandatory Access: read-only
OBJECT-TYPE    
  IpAddress  

wfIpRfRipExportRipMetric 1.3.6.1.4.1.18.3.5.3.2.1.9.1.8
The optional export RIP metric to apply to this filter. Zero means: use the route's actual cost. Only valid for propagate
Status: mandatory Access: read-write
OBJECT-TYPE    
  INTEGER maximum(15)  

wfIpRfOspfImportTable 1.3.6.1.4.1.18.3.5.3.2.1.10
The list of OSPF Import Route Filter Rules in IP
Status: mandatory Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    WfIpRfOspfImportEntry

wfIpRfOspfImportEntry 1.3.6.1.4.1.18.3.5.3.2.1.10.1
An entry in the OSPF Import Route Filter Table
Status: mandatory Access: not-accessible
OBJECT-TYPE    
  WfIpRfOspfImportEntry  

wfIpRfOspfImportCreate 1.3.6.1.4.1.18.3.5.3.2.1.10.1.1
Create/Delete parameter. Default is created. Users perform an SNMP SET operation on this object in order to create/delete this Rule.
Status: mandatory Access: read-write
OBJECT-TYPE    
  INTEGER create(1), delete(2)  

wfIpRfOspfImportEnable 1.3.6.1.4.1.18.3.5.3.2.1.10.1.2
Enable/Disable parameter. Default is enabled. Users perform an SNMP SET operation on this object in order to enable/disable this Rule.
Status: mandatory Access: read-write
OBJECT-TYPE    
  INTEGER enable(1), disable(2)  

wfIpRfOspfImportAddress 1.3.6.1.4.1.18.3.5.3.2.1.10.1.3
The IP Address to which this filter applies
Status: mandatory Access: read-only
OBJECT-TYPE    
  IpAddress  

wfIpRfOspfImportMask 1.3.6.1.4.1.18.3.5.3.2.1.10.1.4
The Mask to which this filter applies. When combined with the Address, a range is specified for application of this rule
Status: mandatory Access: read-only
OBJECT-TYPE    
  IpAddress  

wfIpRfOspfImportAction 1.3.6.1.4.1.18.3.5.3.2.1.10.1.5
The Action of this Filter
Status: mandatory Access: read-write
OBJECT-TYPE    
  INTEGER accept(1), ignore(3)  

wfIpRfOspfImportPreference 1.3.6.1.4.1.18.3.5.3.2.1.10.1.6
The Preference associated with this filter - only valid if accept
Status: mandatory Access: read-write
OBJECT-TYPE    
  INTEGER maximum(16)  

wfIpRfOspfImportType 1.3.6.1.4.1.18.3.5.3.2.1.10.1.7
The OSPF route Type to be concerned with. The valid values are null (any route type), 1 (OSPF external type 1), and 2 (OSPF external type 2).
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER  

wfIpRfOspfImportTag 1.3.6.1.4.1.18.3.5.3.2.1.10.1.8
The OSPF Tag to be concerned with
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER  

wfIpRfOspfExportTable 1.3.6.1.4.1.18.3.5.3.2.1.11
The list of OSPF Export Route Filter Rules in IP
Status: mandatory Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    WfIpRfOspfExportEntry

wfIpRfOspfExportEntry 1.3.6.1.4.1.18.3.5.3.2.1.11.1
An entry in the OSPF Export Route Filter Table
Status: mandatory Access: not-accessible
OBJECT-TYPE    
  WfIpRfOspfExportEntry  

wfIpRfOspfExportCreate 1.3.6.1.4.1.18.3.5.3.2.1.11.1.1
Create/Delete parameter. Default is created. Users perform an SNMP SET operation on this object in order to create/delete this Rule.
Status: mandatory Access: read-write
OBJECT-TYPE    
  INTEGER create(1), delete(2)  

wfIpRfOspfExportEnable 1.3.6.1.4.1.18.3.5.3.2.1.11.1.2
Enable/Disable parameter. Default is enabled. Users perform an SNMP SET operation on this object in order to enable/disable this Rule.
Status: mandatory Access: read-write
OBJECT-TYPE    
  INTEGER enable(1), disable(2)  

wfIpRfOspfExportAddress 1.3.6.1.4.1.18.3.5.3.2.1.11.1.3
The IP address to which this filter applies
Status: mandatory Access: read-only
OBJECT-TYPE    
  IpAddress  

wfIpRfOspfExportMask 1.3.6.1.4.1.18.3.5.3.2.1.11.1.4
The Mask for the Address Above. When combined with the Address, a range is specified for application of this filter rule
Status: mandatory Access: read-only
OBJECT-TYPE    
  IpAddress  

wfIpRfOspfExportFromProtocol 1.3.6.1.4.1.18.3.5.3.2.1.11.1.5
The protocol from which this Information is derived
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER rip(1), ospf(3), direct(4), static(5)  

wfIpRfOspfExportAction 1.3.6.1.4.1.18.3.5.3.2.1.11.1.6
The action of this export filter
Status: mandatory Access: read-write
OBJECT-TYPE    
  INTEGER propa(2), ignore(3)  

wfIpRfOspfExportType 1.3.6.1.4.1.18.3.5.3.2.1.11.1.7
The ospf type to use when this filter matches
Status: mandatory Access: read-write
OBJECT-TYPE    
  INTEGER type1(1), type2(2)  

wfIpRfOspfExportTag 1.3.6.1.4.1.18.3.5.3.2.1.11.1.8
The ospf tag to use when this filter matches
Status: mandatory Access: read-write
OBJECT-TYPE    
  INTEGER  

wfSipL2 1.3.6.1.4.1.18.3.4.14.1
The SIP L2 Table
Status: mandatory Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    WfSipL2Entry

wfSipL2Entry 1.3.6.1.4.1.18.3.4.14.1.1
per circuit SIP Level 2 objects - wfSipL2Index corresponds to Wellfleet circuit number
Status: mandatory Access: not-accessible
OBJECT-TYPE    
  WfSipL2Entry  

wfSipL2Index 1.3.6.1.4.1.18.3.4.14.1.1.1
this corresponds to the Wellfleet circuit number
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER minimum(1), maximum(1024)  

wfSipL2ReceivedCounts 1.3.6.1.4.1.18.3.4.14.1.1.2
total of unerrored received SIP L2 PDUs
Status: mandatory Access: read-only
OBJECT-TYPE    
  Counter  

wfSipL2SentCounts 1.3.6.1.4.1.18.3.4.14.1.1.3
total of unerrored SIP L2 PDU's sent across the SNI
Status: mandatory Access: read-only
OBJECT-TYPE    
  Counter  

wfSipHcsOrCRCErrors 1.3.6.1.4.1.18.3.4.14.1.1.4
total SIP L2 PDUs with HCS or CRC errors
Status: mandatory Access: read-only
OBJECT-TYPE    
  Counter  

wfSipL2PayloadLengthErrors 1.3.6.1.4.1.18.3.4.14.1.1.5
total SIP L2 PDUs with length errors
Status: mandatory Access: read-only
OBJECT-TYPE    
  Counter  

wfSipL2SequenceNumberErrors 1.3.6.1.4.1.18.3.4.14.1.1.6
total SIP L2 PDUs with unexpected sequence numbers
Status: mandatory Access: read-only
OBJECT-TYPE    
  Counter  

wfSipL2MidCurrentlyActiveErrors 1.3.6.1.4.1.18.3.4.14.1.1.7
number of SIP L2 PDUs with BOMs previously started
Status: mandatory Access: read-only
OBJECT-TYPE    
  Counter  

wfSipL2BomOrSSMsMIDErrors 1.3.6.1.4.1.18.3.4.14.1.1.8
number of SIP L2 PDUs with zero BOMs or SSMs not zero
Status: mandatory Access: read-only
OBJECT-TYPE    
  Counter  

wfSipL2EomsMIDErrors 1.3.6.1.4.1.18.3.4.14.1.1.9
number of SIP L2 PDUs with zero EOMs or EOMs without BOMs
Status: mandatory Access: read-only
OBJECT-TYPE    
  Counter  

wfSipDs1Plcp 1.3.6.1.4.1.18.3.4.14.2.1
The SIP DS1 PLCP Table
Status: mandatory Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    WfSipDs1PlcpEntry

wfSipDs1PlcpEntry 1.3.6.1.4.1.18.3.4.14.2.1.1
per circuit DS1 PLCP objects - wfSipDs1PlcpIndex corresponds to Wellfleet circuit number
Status: mandatory Access: not-accessible
OBJECT-TYPE    
  WfSipDs1PlcpEntry  

wfSipDs1PlcpIndex 1.3.6.1.4.1.18.3.4.14.2.1.1.1
this corresponds to the Wellfleet circuit number
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER minimum(1), maximum(1024)  

wfSipDs1PlcpSEFs 1.3.6.1.4.1.18.3.4.14.2.1.1.2
number of second intervals containing one or more severely errored seconds
Status: mandatory Access: read-only
OBJECT-TYPE    
  Counter  

wfSipDs1PlcpAlarmState 1.3.6.1.4.1.18.3.4.14.2.1.1.3
alarm state
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER noalarm(1), receivedfarendalarm(2), incominglof(3)  

wfSipDs1PlcpUASs 1.3.6.1.4.1.18.3.4.14.2.1.1.4
number of second intervals containing one or more unavailable seconds
Status: mandatory Access: read-only
OBJECT-TYPE    
  Counter  

wfSipDs3Plcp 1.3.6.1.4.1.18.3.4.14.2.2
The SIP DS3 PLCP Table
Status: mandatory Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    WfSipDs3PlcpEntry

wfSipDs3PlcpEntry 1.3.6.1.4.1.18.3.4.14.2.2.1
per circuit DS3 PLCP objects - wfSipDs3PlcpIndex corresponds to Wellfleet circuit number
Status: mandatory Access: not-accessible
OBJECT-TYPE    
  WfSipDs3PlcpEntry  

wfSipDs3PlcpIndex 1.3.6.1.4.1.18.3.4.14.2.2.1.1
this corresponds to the Wellfleet circuit number
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER minimum(1), maximum(1024)  

wfSipDs3PlcpSEFs 1.3.6.1.4.1.18.3.4.14.2.2.1.2
number of second intervals containing one or more severely errored seconds
Status: mandatory Access: read-only
OBJECT-TYPE    
  Counter  

wfSipDs3PlcpAlarmState 1.3.6.1.4.1.18.3.4.14.2.2.1.3
alarm state
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER noalarm(1), receivedfarendalarm(2), incominglof(3)  

wfSipDs3PlcpUASs 1.3.6.1.4.1.18.3.4.14.2.2.1.4
number of second intervals containing one or more unavailable seconds
Status: mandatory Access: read-only
OBJECT-TYPE    
  Counter  

wfSmdsCircuitTable 1.3.6.1.4.1.18.3.5.9.3
The Wellfleet SMDS Circuit Record
Status: mandatory Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    WfSmdsCircuitEntry

wfSmdsCircuitEntry 1.3.6.1.4.1.18.3.5.9.3.1
per Wellfleet circuit SMDS configuration parameters and counters
Status: mandatory Access: not-accessible
OBJECT-TYPE    
  WfSmdsCircuitEntry  

wfSmdsCircuitDelete 1.3.6.1.4.1.18.3.5.9.3.1.1
create/delete parameter, dflt = created
Status: mandatory Access: read-write
OBJECT-TYPE    
  INTEGER created(1), deleted(2)  

wfSmdsCircuitDisable 1.3.6.1.4.1.18.3.5.9.3.1.2
enable/disable parameter, dflt = enabled
Status: mandatory Access: read-write
OBJECT-TYPE    
  INTEGER enabled(1), disabled(2)  

wfSmdsCircuitState 1.3.6.1.4.1.18.3.5.9.3.1.3
SMDS state variable, Up, Down Init, Not Present
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER up(1), down(2), init(3), notpresent(4)  

wfSmdsCircuitID 1.3.6.1.4.1.18.3.5.9.3.1.4
cct number for this instance
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER minimum(1), maximum(1023)  

wfSmdsCircuitIndivAddr 1.3.6.1.4.1.18.3.5.9.3.1.5
SMDS E.164 Individual address for this Wellfleet circuit - must be 8 octets long
Status: mandatory Access: read-write
OBJECT-TYPE    
  OCTET STRING  

wfSmdsCircuitGroupAddr 1.3.6.1.4.1.18.3.5.9.3.1.6
SMDS E.164 Group address for this Wellfleet circuit - must be 8 octets long
Status: mandatory Access: read-write
OBJECT-TYPE    
  OCTET STRING  

wfSmdsCircuitArpAddr 1.3.6.1.4.1.18.3.5.9.3.1.7
SMDS E.164 ARP address for this Wellfleet circuit - must be 8 octets long
Status: mandatory Access: read-write
OBJECT-TYPE    
  OCTET STRING  

wfSmdsCircuitDisableHrtbtPoll 1.3.6.1.4.1.18.3.5.9.3.1.8
determine use of DXI heartbeat poll
Status: mandatory Access: read-write
OBJECT-TYPE    
  INTEGER enabled(1), disabled(2)  

wfSmdsCircuitHrtbtPollInterval 1.3.6.1.4.1.18.3.5.9.3.1.9
heartbeat polling messages get sent every this many seconds - we don't want the polling interval to be less than or equal to the unacknowledgment timer, which is 5 seconds
Status: mandatory Access: read-write
OBJECT-TYPE    
  INTEGER minimum(6), default(10)  

wfSmdsCircuitHrtbtPollDownCount 1.3.6.1.4.1.18.3.5.9.3.1.10
if this many consecutive heartbeat polling messages go unacknowledged, log an event declaring the line down
Status: mandatory Access: read-write
OBJECT-TYPE    
  INTEGER minimum(1), default(3)  

wfSmdsCircuitDisableNetMgmt 1.3.6.1.4.1.18.3.5.9.3.1.11
determine use of LMI network management
Status: mandatory Access: read-write
OBJECT-TYPE    
  INTEGER enabled(1), disabled(2)  

wfSmdsCircuitSipL3ReceivedIndividualDAs 1.3.6.1.4.1.18.3.5.9.3.1.12
The total number of individually addressed SIP Level 3 PDUs received from the remote system across the SNI. The total includes only unerrored L3PDUs.
Status: mandatory Access: read-only
OBJECT-TYPE    
  Counter  

wfSmdsCircuitSipL3ReceivedGAs 1.3.6.1.4.1.18.3.5.9.3.1.13
The total number of group addressed SIP Level 3 PDUs received from the remote system across the SNI. The total includes only unerrored L3PDUs.
Status: mandatory Access: read-only
OBJECT-TYPE    
  Counter  

wfSmdsCircuitSipL3SentIndividualDAs 1.3.6.1.4.1.18.3.5.9.3.1.14
The number of individually addressed SIP Level 3 PDUs that have been sent by this system across the SNI.
Status: mandatory Access: read-only
OBJECT-TYPE    
  Counter  

wfSmdsCircuitSipL3SentGAs 1.3.6.1.4.1.18.3.5.9.3.1.15
The number of group addressed SIP L3PDUs that have been sent by this system across the SNI.
Status: mandatory Access: read-only
OBJECT-TYPE    
  Counter  

wfSmdsCircuitSipL3VersionSupport 1.3.6.1.4.1.18.3.5.9.3.1.16
A value which indicates the version(s) of SIP that this interface supports. The value is a sum. This sum initially takes the value zero. For each version, V, that this interface supports, 2 raised to (V - 1) is added to the sum. For example, a port supporting versions 1 and 2 would have a value of (2^(1-1)+2^(2-1))=3. The SipL3VersionSupport is effectively a bit mask with Version 1 equal to the least significant bit (LSB).
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER version(1)  

wfSnmp 1.3.6.1.4.1.18.3.5.3.5.1
OBJECT IDENTIFIER    

wfSnmpDisable 1.3.6.1.4.1.18.3.5.3.5.1.1
Enables or disables the SNMP subsystem
Status: mandatory Access: read-write
OBJECT-TYPE    
  INTEGER enabled(1), disabled(2)  

wfSnmpUseLock 1.3.6.1.4.1.18.3.5.3.5.1.2
Flag to indicate whether locking mechanism is enabled or disabled
Status: mandatory Access: read-write
OBJECT-TYPE    
  INTEGER enabled(1), disabled(2)  

wfSnmpLockAddress 1.3.6.1.4.1.18.3.5.3.5.1.3
Address of remote manager that is enforcing the lock. This value is set by the SNMP agent. Remote managers are only allowed to clear it.
Status: mandatory Access: read-write
OBJECT-TYPE    
  IpAddress  

wfSnmpLockTimeOut 1.3.6.1.4.1.18.3.5.3.5.1.4
The maximum time (in minutes) a lock can be idle before it is cleared.
Status: mandatory Access: read-write
OBJECT-TYPE    
  INTEGER default(2), minimum(1), maximum(60)  

wfSnmpAuth 1.3.6.1.4.1.18.3.5.3.5.1.5
The type of authentication used by the agent
Status: mandatory Access: read-write
OBJECT-TYPE    
  INTEGER trivial(1), party(2)  

wfSnmpInPkts 1.3.6.1.4.1.18.3.5.3.5.1.6
Total number of PDUs received by SNMP from transport entity
Status: mandatory Access: read-only
OBJECT-TYPE    
  Counter  

wfSnmpOutPkts 1.3.6.1.4.1.18.3.5.3.5.1.7
Total number of PDUs sent by SNMP to transport entity
Status: mandatory Access: read-only
OBJECT-TYPE    
  Counter  

wfSnmpInBadVersions 1.3.6.1.4.1.18.3.5.3.5.1.8
Total number of PDUs requesting unsupported versions
Status: mandatory Access: read-only
OBJECT-TYPE    
  Counter  

wfSnmpInBadCommunityNames 1.3.6.1.4.1.18.3.5.3.5.1.9
Total number of PDUs which had an invalid community string
Status: mandatory Access: read-only
OBJECT-TYPE    
  Counter  

wfSnmpInBadCommunityUses 1.3.6.1.4.1.18.3.5.3.5.1.10
Total number of PDUs requesting an operation unsupported by the community
Status: mandatory Access: read-only
OBJECT-TYPE    
  Counter  

wfSnmpInASNParseErrs 1.3.6.1.4.1.18.3.5.3.5.1.11
Total number of ASN.1 parsing errors during decoding
Status: mandatory Access: read-only
OBJECT-TYPE    
  Counter  

wfSnmpInBadTypes 1.3.6.1.4.1.18.3.5.3.5.1.12
Total number of PDUs having an unknown PDU type
Status: mandatory Access: read-only
OBJECT-TYPE    
  Counter  

wfSnmpInTooBigs 1.3.6.1.4.1.18.3.5.3.5.1.13
Total number of PDUs delivered with ErrorStatus='tooBig'
Status: mandatory Access: read-only
OBJECT-TYPE    
  Counter  

wfSnmpInNoSuchNames 1.3.6.1.4.1.18.3.5.3.5.1.14
Total number of PDUs delivered with ErrorStatus='noSuchName'
Status: mandatory Access: read-only
OBJECT-TYPE    
  Counter  

wfSnmpInBadValues 1.3.6.1.4.1.18.3.5.3.5.1.15
Total number of PDUs delivered with ErrorStatus='badValue'
Status: mandatory Access: read-only
OBJECT-TYPE    
  Counter  

wfSnmpInReadOnlys 1.3.6.1.4.1.18.3.5.3.5.1.16
Total number of PDUs delivered with ErrorStatus='readOnly'
Status: mandatory Access: read-only
OBJECT-TYPE    
  Counter  

wfSnmpInGenErrs 1.3.6.1.4.1.18.3.5.3.5.1.17
Total number of PDUs delivered with ErrorStatus='genErr'
Status: mandatory Access: read-only
OBJECT-TYPE    
  Counter  

wfSnmpInTotalReqVars 1.3.6.1.4.1.18.3.5.3.5.1.18
Total number of MIB objects retrieved successfully by the agent
Status: mandatory Access: read-only
OBJECT-TYPE    
  Counter  

wfSnmpInTotalSetVars 1.3.6.1.4.1.18.3.5.3.5.1.19
Total number of MIB objects which have been SET successfully
Status: mandatory Access: read-only
OBJECT-TYPE    
  Counter  

wfSnmpInGetRequests 1.3.6.1.4.1.18.3.5.3.5.1.20
Total number of Get-Request PDUS accepted and processed
Status: mandatory Access: read-only
OBJECT-TYPE    
  Counter  

wfSnmpInGetNexts 1.3.6.1.4.1.18.3.5.3.5.1.21
Total number of GetNext-Request PDUS accepted and processed
Status: mandatory Access: read-only
OBJECT-TYPE    
  Counter  

wfSnmpInSetRequests 1.3.6.1.4.1.18.3.5.3.5.1.22
Total number of Set-Request PDUS accepted and processed
Status: mandatory Access: read-only
OBJECT-TYPE    
  Counter  

wfSnmpInGetResponses 1.3.6.1.4.1.18.3.5.3.5.1.23
Total number of GetResponse PDUs accepted and processed
Status: mandatory Access: read-only
OBJECT-TYPE    
  Counter  

wfSnmpInTraps 1.3.6.1.4.1.18.3.5.3.5.1.24
Total number of Trap PDUs accepted and processed
Status: mandatory Access: read-only
OBJECT-TYPE    
  Counter  

wfSnmpOutTooBigs 1.3.6.1.4.1.18.3.5.3.5.1.25
Total number of PDUs generated by the agent with ErrorStatus='tooBig'
Status: mandatory Access: read-only
OBJECT-TYPE    
  Counter  

wfSnmpOutNoSuchNames 1.3.6.1.4.1.18.3.5.3.5.1.26
Total number of PDUs generated by the agent with ErrorStatus='noSuchName'
Status: mandatory Access: read-only
OBJECT-TYPE    
  Counter  

wfSnmpOutBadValues 1.3.6.1.4.1.18.3.5.3.5.1.27
Total number of PDUs generated by the agent with ErrorStatus='badValue'
Status: mandatory Access: read-only
OBJECT-TYPE    
  Counter  

wfSnmpOutReadOnlys 1.3.6.1.4.1.18.3.5.3.5.1.28
Total number of PDUs generated by the agent with ErrorStatus='readOnly'
Status: mandatory Access: read-only
OBJECT-TYPE    
  Counter  

wfSnmpOutGenErrs 1.3.6.1.4.1.18.3.5.3.5.1.29
Total number of PDUs generated by the agent with ErrorStatus='genErr'
Status: mandatory Access: read-only
OBJECT-TYPE    
  Counter  

wfSnmpOutGetRequests 1.3.6.1.4.1.18.3.5.3.5.1.30
Total number of Get-Request PDUs generated by the agent
Status: mandatory Access: read-only
OBJECT-TYPE    
  Counter  

wfSnmpOutGetNexts 1.3.6.1.4.1.18.3.5.3.5.1.31
Total number of Get-Next-Request PDUs generated by the agent
Status: mandatory Access: read-only
OBJECT-TYPE    
  Counter  

wfSnmpOutSetRequests 1.3.6.1.4.1.18.3.5.3.5.1.32
Total number of Set-Request PDUs generated by the agent
Status: mandatory Access: read-only
OBJECT-TYPE    
  Counter  

wfSnmpOutGetResponses 1.3.6.1.4.1.18.3.5.3.5.1.33
Total number of Get-Response PDUs generated by the agent
Status: mandatory Access: read-only
OBJECT-TYPE    
  Counter  

wfSnmpOutTraps 1.3.6.1.4.1.18.3.5.3.5.1.34
Total number of Trap PDUs generated by the agent
Status: mandatory Access: read-only
OBJECT-TYPE    
  Counter  

wfSnmpEnableAuthTraps 1.3.6.1.4.1.18.3.5.3.5.1.35
Idicates whether agent can generate Authentication Failure Traps
Status: mandatory Access: read-write
OBJECT-TYPE    
  INTEGER enabled(1), disabled(2)  

wfSnmpTrapDebug 1.3.6.1.4.1.18.3.5.3.5.1.36
This attribute controls the specific trap filter for debug messages
Status: mandatory Access: read-write
OBJECT-TYPE    
  INTEGER on(1), off(2)  

wfSnmpTrapTrace 1.3.6.1.4.1.18.3.5.3.5.1.37
This attribute controls the specific trap filter for trace messages
Status: mandatory Access: read-write
OBJECT-TYPE    
  INTEGER on(1), off(2)  

wfSnmpTrapInfo 1.3.6.1.4.1.18.3.5.3.5.1.38
This attribute controls the specific trap filter for informational messages
Status: mandatory Access: read-write
OBJECT-TYPE    
  INTEGER on(1), off(2)  

wfSnmpTrapWarn 1.3.6.1.4.1.18.3.5.3.5.1.39
This attribute controls the specific trap filter for warning messages
Status: mandatory Access: read-write
OBJECT-TYPE    
  INTEGER on(1), off(2)  

wfSnmpTrapFault 1.3.6.1.4.1.18.3.5.3.5.1.40
This attribute controls the specific trap filter for fault messages
Status: mandatory Access: read-write
OBJECT-TYPE    
  INTEGER on(1), off(2)  

wfSnmpCommTable 1.3.6.1.4.1.18.3.5.3.5.2
A table containing valid management communities
Status: mandatory Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    WfSnmpCommEntry

wfSnmpCommEntry 1.3.6.1.4.1.18.3.5.3.5.2.1
Information about a particular community
Status: mandatory Access: not-accessible
OBJECT-TYPE    
  WfSnmpCommEntry  

wfSnmpCommDelete 1.3.6.1.4.1.18.3.5.3.5.2.1.1
A flag to indicate community instance deletion
Status: mandatory Access: read-write
OBJECT-TYPE    
  INTEGER created(1), deleted(2)  

wfSnmpCommIndex 1.3.6.1.4.1.18.3.5.3.5.2.1.2
A unique numeric value that has a one to one correspondence with the community name
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER  

wfSnmpCommName 1.3.6.1.4.1.18.3.5.3.5.2.1.3
Community name
Status: mandatory Access: read-write
OBJECT-TYPE    
  DisplayString  

wfSnmpCommAccess 1.3.6.1.4.1.18.3.5.3.5.2.1.4
Community access mode
Status: mandatory Access: read-write
OBJECT-TYPE    
  INTEGER readonly(1), readwrite(2)  

wfSnmpMgrTable 1.3.6.1.4.1.18.3.5.3.5.3
A table containing managers and their respective communities
Status: mandatory Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    WfSnmpMgrEntry

wfSnmpMgrEntry 1.3.6.1.4.1.18.3.5.3.5.3.1
Information about a manager of a community
Status: mandatory Access: not-accessible
OBJECT-TYPE    
  WfSnmpMgrEntry  

wfSnmpMgrDelete 1.3.6.1.4.1.18.3.5.3.5.3.1.1
A flag to indicate manager instance deletion */
Status: mandatory Access: read-write
OBJECT-TYPE    
  INTEGER created(1), deleted(2)  

wfSnmpMgrCommIndex 1.3.6.1.4.1.18.3.5.3.5.3.1.2
Associates this manager with a community in the community table
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER  

wfSnmpMgrAddress 1.3.6.1.4.1.18.3.5.3.5.3.1.3
IP Address of this manager
Status: mandatory Access: read-only
OBJECT-TYPE    
  IpAddress  

wfSnmpMgrName 1.3.6.1.4.1.18.3.5.3.5.3.1.4
A name for this manager
Status: mandatory Access: read-write
OBJECT-TYPE    
  DisplayString  

wfSnmpMgrTrapPort 1.3.6.1.4.1.18.3.5.3.5.3.1.5
The UDP Port on which this manager is listening for traps
Status: mandatory Access: read-write
OBJECT-TYPE    
  INTEGER  

wfSnmpMgrTraps 1.3.6.1.4.1.18.3.5.3.5.3.1.6
Allowable Traps to be sent to Manager, defaults to only generic trap types
Status: mandatory Access: read-write
OBJECT-TYPE    
  INTEGER none(1), generic(2), specific(4), all(7)  

wfBrStp 1.3.6.1.4.1.18.3.5.1.2.1
OBJECT IDENTIFIER    

wfBrStpBaseDelete 1.3.6.1.4.1.18.3.5.1.2.1.1
Create/Delete parameter. Default is created. Users perform an SNMP SET operation on this object in order to create/delete the Spanning tree.
Status: mandatory Access: read-write
OBJECT-TYPE    
  INTEGER created(1), deleted(2)  

wfBrStpBaseEnable 1.3.6.1.4.1.18.3.5.1.2.1.2
Enable/Disable parameter. Default is enabled. Users perform an SNMP SET operation on this object in order to enable/disable the spanning tree.
Status: mandatory Access: read-write
OBJECT-TYPE    
  INTEGER enabled(1), disabled(2)  

wfBrStpBaseState 1.3.6.1.4.1.18.3.5.1.2.1.3
The current state of the spanning tree.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER up(1), down(2), init(3), pres(4)  

wfBrStpProtocolSpecification 1.3.6.1.4.1.18.3.5.1.2.1.4
The version of the Spanning Tree protocol being run.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER unknown(1), declb100(2), ieee8021d(3)  

wfBrStpBridgeID 1.3.6.1.4.1.18.3.5.1.2.1.5
The Spanning Tree Bridge ID assigned to this bridge. It is a 8-octet string. The first two octets make up the bridge priority, and the last six are the MAC address of this bridge, which is commonly the MAC address of the first port on the bridge.
Status: mandatory Access: read-write
OBJECT-TYPE    
  OCTET STRING  

wfBrStpTimeSinceTopologyChange 1.3.6.1.4.1.18.3.5.1.2.1.6
The time (in hundredths of a second) since the last topology change was detected by the bridge.
Status: mandatory Access: read-only
OBJECT-TYPE    
  Counter  

wfBrStpTopChanges 1.3.6.1.4.1.18.3.5.1.2.1.7
The total number of topology changes detected by this bridge since it was last reset or initialized
Status: mandatory Access: read-only
OBJECT-TYPE    
  Counter  

wfBrStpDesignatedRoot 1.3.6.1.4.1.18.3.5.1.2.1.8
The bridge ID of the root of the spanning tree as determined by the Spanning Tree Protocol as executed by the bridge. This value is used as the Root Identifier parameter in all Configuration Bridge PDUs originated by this node. It is a 8-octet string. The first two octets make up the priority, and the last six are the MAC address of the designated root bridge.
Status: mandatory Access: read-only
OBJECT-TYPE    
  OCTET STRING  

wfBrStpRootCost 1.3.6.1.4.1.18.3.5.1.2.1.9
The cost of the path to the root as seen from this bridge.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER  

wfBrStpRootPort 1.3.6.1.4.1.18.3.5.1.2.1.10
The port identifier of the port which offers the lowest cost path from this bridge to the root bridge.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER  

wfBrStpMaxAge 1.3.6.1.4.1.18.3.5.1.2.1.11
The maximum age of the Spanning Tree Protocol information learned from the network on any port before it is discarded, in hundredths of a second. This represents the value actually in use by the bridge.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER  

wfBrStpHelloTime 1.3.6.1.4.1.18.3.5.1.2.1.12
The amount of time between transmission of configuration BPDUs by this bridge on any port, when it is the root of the spanning tree or trying to become so, in hundreths of a second. This represents the value actually in use by the bridge.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER  

wfBrStpHoldTime 1.3.6.1.4.1.18.3.5.1.2.1.13
The value that determines the interval length during which no more than two configuration BPDUs shall be transmitted by this bridge, in hundredths of a second.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER time(100)  

wfBrStpForwardDelay 1.3.6.1.4.1.18.3.5.1.2.1.14
The time, in hundredths of a second, that a port on this bridge will stay in a transitional state (e.g. LISTENING) before moving to the next state (e.g. LEARNING). This value is also used to age all dynamic entries in the Forwarding Database when a topology changed has been detected and is underway. This represents the value actually in use by the bridge.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER  

wfBrStpBridgeMaxAge 1.3.6.1.4.1.18.3.5.1.2.1.15
The value that all bridges use for MaxAge when this bridge acting as the root.
Status: mandatory Access: read-write
OBJECT-TYPE    
  INTEGER minimum(600), default(2000), maximum(4000)  

wfBrStpBridgeHelloTime 1.3.6.1.4.1.18.3.5.1.2.1.16
The value that all bridges use for HelloTime when this bridge acting as the root.
Status: mandatory Access: read-write
OBJECT-TYPE    
  INTEGER minimum(100), default(200), maximum(1000)  

wfBrStpBridgeForwardDelay 1.3.6.1.4.1.18.3.5.1.2.1.17
The value that all bridges use for ForwardDelay when this bridge acting as the root.
Status: mandatory Access: read-write
OBJECT-TYPE    
  INTEGER minimum(400), default(1500), maximum(3000)  

wfBrStpInterface 1.3.6.1.4.1.18.3.5.1.2.2
inst_id[1] = wfBrStpInterfaceCircuit
Status: mandatory Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    WfBrStpInterfaceEntry

wfBrStpInterfaceEntry 1.3.6.1.4.1.18.3.5.1.2.2.1
An entry in wfBrStpInterface.
Status: mandatory Access: not-accessible
OBJECT-TYPE    
  WfBrStpInterfaceEntry  

wfBrStpInterfaceDelete 1.3.6.1.4.1.18.3.5.1.2.2.1.1
Create/Delete parameter. Default is created. Users perform an SNMP SET operation on this object in order to create/delete an interface for the Spanning Tree.
Status: mandatory Access: read-write
OBJECT-TYPE    
  INTEGER created(1), deleted(2)  

wfBrStpInterfaceEnable 1.3.6.1.4.1.18.3.5.1.2.2.1.2
Enable/Disable parameter. Default is enabled. Users perform an SNMP SET operation on this object in order to enable/disable an interface for the Spanning Tree.
Status: mandatory Access: read-write
OBJECT-TYPE    
  INTEGER enabled(1), disabled(2)  

wfBrStpInterfaceCircuit 1.3.6.1.4.1.18.3.5.1.2.2.1.3
The circuit number on which this interface is defined.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER  

wfBrStpInterfacePriority 1.3.6.1.4.1.18.3.5.1.2.2.1.4
The value of the priority field which is contained in the first octet of the (2 octet long) port ID for this circuit. The other octet of the port ID is given by wfBrStpInterfaceCircuit.
Status: mandatory Access: read-write
OBJECT-TYPE    
  INTEGER default(128), maximum(255)  

wfBrStpInterfaceState 1.3.6.1.4.1.18.3.5.1.2.2.1.5
The current state of the port as defined by the application of the Spanning Tree Protocol.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER disabled(1), blocking(2), listening(3), learning(4), forwarding(5), broken(6)  

wfBrStpInterfaceMultiCastAddr 1.3.6.1.4.1.18.3.5.1.2.2.1.6
The MAC address used as the destination for all BPDU packets generated out this port.
Status: mandatory Access: read-only
OBJECT-TYPE    
  OCTET STRING  

wfBrStpInterfacePathCost 1.3.6.1.4.1.18.3.5.1.2.2.1.7
The contribution of this port the the root path cost of paths toward the spanning tree root which include this port.
Status: mandatory Access: read-write
OBJECT-TYPE    
  INTEGER minimum(1), maximum(65535)  

wfBrStpInterfaceDesignatedRoot 1.3.6.1.4.1.18.3.5.1.2.2.1.8
The unique Bridge Identifier of the Bridge recorded as the Root in the Configuration BPDUs transmitted by the Designated Bridge for the segment to which this port is attached. Bridge IDs are made up of a 2-byte priority field, and a 6-byte MAC address.
Status: mandatory Access: read-only
OBJECT-TYPE    
  OCTET STRING  

wfBrStpInterfaceDesignatedCost 1.3.6.1.4.1.18.3.5.1.2.2.1.9
The path cost of the Designated Port of the segment connected to this port. This value is compared to the Root Path Cost field in received bridge PDUs.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER  

wfBrStpInterfaceDesignatedBridge 1.3.6.1.4.1.18.3.5.1.2.2.1.10
The Bridge Identifier of the bridge which this port considers to be the Designated Bridge for this port's segment.
Status: mandatory Access: read-only
OBJECT-TYPE    
  OCTET STRING  

wfBrStpInterfaceDesignatedPort 1.3.6.1.4.1.18.3.5.1.2.2.1.11
The Port Identifier of the port on the Designated Bridge for this port's segment.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER  

wfBrStpInterfaceForwardTransitions 1.3.6.1.4.1.18.3.5.1.2.2.1.12
The number of times this port has transitioned from the Learning State to the Forwarding state.
Status: mandatory Access: read-only
OBJECT-TYPE    
  Counter  

wfBrStpInterfacePktsXmitd 1.3.6.1.4.1.18.3.5.1.2.2.1.13
The number of BPDU packets transmitted out this port
Status: mandatory Access: read-only
OBJECT-TYPE    
  Counter  

wfBrStpInterfacePktsRcvd 1.3.6.1.4.1.18.3.5.1.2.2.1.14
The number of BPDU packets received on this port
Status: mandatory Access: read-only
OBJECT-TYPE    
  Counter  

wfBrSr 1.3.6.1.4.1.18.3.5.1.1.2.1
OBJECT IDENTIFIER    

wfBrSrBaseDelete 1.3.6.1.4.1.18.3.5.1.1.2.1.1
Create/Delete parameter. Default is created. Users perform an SNMP SET operation on this object in order to create/delete the bridge.
Status: mandatory Access: read-write
OBJECT-TYPE    
  INTEGER created(1), deleted(2)  

wfBrSrBaseDisable 1.3.6.1.4.1.18.3.5.1.1.2.1.2
Enable/Disable parameter. Default is enabled. Users perform an SNMP SET operation on this object in order to enable/disable the bridge.
Status: mandatory Access: read-write
OBJECT-TYPE    
  INTEGER enabled(1), disabled(2)  

wfBrSrBaseState 1.3.6.1.4.1.18.3.5.1.1.2.1.3
The current state of the SR bridge.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER up(1), down(2), init(3), notpresent(4)  

wfBrSrBaseInternalLanId 1.3.6.1.4.1.18.3.5.1.1.2.1.4
The SR bridge internal LAN ID
Status: mandatory Access: read-write
OBJECT-TYPE    
  INTEGER  

wfBrSrBaseBridgeId 1.3.6.1.4.1.18.3.5.1.1.2.1.5
The SR bridge Id
Status: mandatory Access: read-write
OBJECT-TYPE    
  INTEGER  

wfBrSrBaseGroupLanId 1.3.6.1.4.1.18.3.5.1.1.2.1.6
The SR bridge Group LAN ID
Status: mandatory Access: read-write
OBJECT-TYPE    
  INTEGER  

wfBrSrBaseIpEncapsDisable 1.3.6.1.4.1.18.3.5.1.1.2.1.7
IP Encapsulation Enable/Disable
Status: mandatory Access: read-write
OBJECT-TYPE    
  INTEGER enabled(1), disabled(2)  

wfBrSrBaseIpNetworkRingId 1.3.6.1.4.1.18.3.5.1.1.2.1.8
The ring number of a connected IP network
Status: mandatory Access: read-write
OBJECT-TYPE    
  INTEGER  

wfBrSrBaseIpInReceives 1.3.6.1.4.1.18.3.5.1.1.2.1.9
The number IP frames received by the network
Status: mandatory Access: read-only
OBJECT-TYPE    
  Counter  

wfBrSrBaseIpSeqErrors 1.3.6.1.4.1.18.3.5.1.1.2.1.10
The number IP frames received by the network
Status: mandatory Access: read-only
OBJECT-TYPE    
  Counter  

wfBrSrBaseIpMtuSize 1.3.6.1.4.1.18.3.5.1.1.2.1.11
to the LF code in the Route Control field
Status: mandatory Access: read-write
OBJECT-TYPE    
  INTEGER  

wfBrSrInterfaceTable 1.3.6.1.4.1.18.3.5.1.1.2.2
A table that contains information about every interface that is associated with this source routing bridge. inst_id[1] = wfBrSrInterfaceCircuit
Status: mandatory Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    WfBrSrInterfaceEntry

wfBrSrInterfaceEntry 1.3.6.1.4.1.18.3.5.1.1.2.2.1
An entry in wfBrSrInterface.
Status: mandatory Access: not-accessible
OBJECT-TYPE    
  WfBrSrInterfaceEntry  

wfBrSrInterfaceDelete 1.3.6.1.4.1.18.3.5.1.1.2.2.1.1
Create/Delete parameter. Default is created. Users perform an SNMP SET operation on this object in order to create/delete an interface.
Status: mandatory Access: read-write
OBJECT-TYPE    
  INTEGER created(1), deleted(2)  

wfBrSrInterfaceDisable 1.3.6.1.4.1.18.3.5.1.1.2.2.1.2
Enable/Disable parameter. Default is enabled. Users perform an SNMP SET operation on this object in order to enable/disable an interface.
Status: mandatory Access: read-write
OBJECT-TYPE    
  INTEGER enabled(1), disabled(2)  

wfBrSrInterfaceState 1.3.6.1.4.1.18.3.5.1.1.2.2.1.3
The current state of the interface.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER up(1), down(2), init(3), notpresent(4)  

wfBrSrInterfaceCircuit 1.3.6.1.4.1.18.3.5.1.1.2.2.1.4
The circuit that this interface runs over.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER  

wfBrSrInterfaceMaxRds 1.3.6.1.4.1.18.3.5.1.1.2.2.1.5
The maximum number of RDs permitted in incoming explorer frames
Status: mandatory Access: read-write
OBJECT-TYPE    
  INTEGER  

wfBrSrInterfaceRing 1.3.6.1.4.1.18.3.5.1.1.2.2.1.6
The ring number of the source routing circuit. Even non-ring circuit need a ring number if it is to do source routing
Status: mandatory Access: read-write
OBJECT-TYPE    
  INTEGER  

wfBrSrInterfaceBlockOutSte 1.3.6.1.4.1.18.3.5.1.1.2.2.1.7
Enables blocking of outbound STEs
Status: mandatory Access: read-write
OBJECT-TYPE    
  INTEGER block(1), accept(2)  

wfBrSrInterfaceBlockInSte 1.3.6.1.4.1.18.3.5.1.1.2.2.1.8
Enables blocking of inbound STEs
Status: mandatory Access: read-write
OBJECT-TYPE    
  INTEGER block(1), accept(2)  

wfBrSrInterfaceBlockIp 1.3.6.1.4.1.18.3.5.1.1.2.2.1.9
Enables blocking of inbound explorers that have have already been through the IP network
Status: mandatory Access: read-write
OBJECT-TYPE    
  INTEGER block(1), accept(2)  

wfBrSrInterfaceIpAddress 1.3.6.1.4.1.18.3.5.1.1.2.2.1.10
Ip address for this ring. This should match the the IP address in the IP MIB
Status: mandatory Access: read-write
OBJECT-TYPE    
  IpAddress  

wfBrSrInterfaceInFrames 1.3.6.1.4.1.18.3.5.1.1.2.2.1.11
The number of frames that have been received by this interface from its circuit.
Status: mandatory Access: read-only
OBJECT-TYPE    
  Counter  

wfBrSrInterfaceOutFrames 1.3.6.1.4.1.18.3.5.1.1.2.2.1.12
The number of frames that have been transmitted by this interface
Status: mandatory Access: read-only
OBJECT-TYPE    
  Counter  

wfBrSrInterfaceOutIpFrames 1.3.6.1.4.1.18.3.5.1.1.2.2.1.13
The number of frames that have been transmitted by this interface to the IP network
Status: mandatory Access: read-only
OBJECT-TYPE    
  Counter  

wfBrSrInterfaceDropInvalidRcs 1.3.6.1.4.1.18.3.5.1.1.2.2.1.14
Count of frames received which were discarded because of a bad Route Control field
Status: mandatory Access: read-only
OBJECT-TYPE    
  Counter  

wfBrSrInterfaceDropInvalidRings 1.3.6.1.4.1.18.3.5.1.1.2.2.1.15
Count of frames received which were discarded because of a invalid incoming ring
Status: mandatory Access: read-only
OBJECT-TYPE    
  Counter  

wfBrSrInterfaceDropSrfs 1.3.6.1.4.1.18.3.5.1.1.2.2.1.16
Count of specifically routed frames received which were discarded due to filtering or no next circuit
Status: mandatory Access: read-only
OBJECT-TYPE    
  Counter  

wfBrSrBridgeTable 1.3.6.1.4.1.18.3.5.1.1.2.3
A table that contains the bridge numbers used by Wellfleet bridges in a source routing network inst_id[2] = wfBrSrBridgeId
Status: mandatory Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    WfBrSrBridgeEntry

wfBrSrBridgeEntry 1.3.6.1.4.1.18.3.5.1.1.2.3.1
An entry in wfBrSrBridge.
Status: mandatory Access: not-accessible
OBJECT-TYPE    
  WfBrSrBridgeEntry  

wfBrSrBridgeDelete 1.3.6.1.4.1.18.3.5.1.1.2.3.1.1
Create/Delete parameter. Default is created. Users perform an SNMP SET operation on this object in order to create/delete an IP encapsulation peer record.
Status: mandatory Access: read-write
OBJECT-TYPE    
  INTEGER created(1), deleted(2)  

wfBrSrBridgeId 1.3.6.1.4.1.18.3.5.1.1.2.3.1.2
The Bridge Id reserved for Wellfleet bridges
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER  

wfBrSrIpExplorerTable 1.3.6.1.4.1.18.3.5.1.1.2.4
A table that contains the table of IP addresses to which source routing explorers should be sent inst_id[2] = wfBrSrIpExplorerAddress
Status: mandatory Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    WfBrSrIpExplorerEntry

wfBrSrIpExplorerEntry 1.3.6.1.4.1.18.3.5.1.1.2.4.1
An entry in wfBrSrIpExplorer.
Status: mandatory Access: not-accessible
OBJECT-TYPE    
  WfBrSrIpExplorerEntry  

wfBrSrIpExplorerDelete 1.3.6.1.4.1.18.3.5.1.1.2.4.1.1
Create/Delete parameter. Default is created. Users perform an SNMP SET operation on this object in order to create/delete an IP encapsulation peer record.
Status: mandatory Access: read-write
OBJECT-TYPE    
  INTEGER created(1), deleted(2)  

wfBrSrIpExplorerAddr 1.3.6.1.4.1.18.3.5.1.1.2.4.1.2
The IP address of this encapsulation peer.
Status: mandatory Access: read-only
OBJECT-TYPE    
  IpAddress  

wfBrSrIpEncapsTable 1.3.6.1.4.1.18.3.5.1.1.2.5
A table that contains information about IP Encapsulation ring-to-IP Address mappings. This information is used to make the 'next ring' IP Address decision. inst = wfBrSrIpEncapsRing
Status: mandatory Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    WfBrSrIpEncapsEntry

wfBrSrIpEncapsEntry 1.3.6.1.4.1.18.3.5.1.1.2.5.1
An entry in the wfBrSrIpEncapsTable.
Status: mandatory Access: not-accessible
OBJECT-TYPE    
  WfBrSrIpEncapsEntry  

wfBrSrIpEncapsRing 1.3.6.1.4.1.18.3.5.1.1.2.5.1.1
The remote ring number for which we have a ring to IP Address mapping.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER  

wfBrSrIpEncapsIpAddress 1.3.6.1.4.1.18.3.5.1.1.2.5.1.2
The IP Address of the Wellfleet IP Encapsulation peer to which this ring is connected.
Status: mandatory Access: read-only
OBJECT-TYPE    
  IpAddress  

wfBrSrIpEncapsStatus 1.3.6.1.4.1.18.3.5.1.1.2.5.1.3
The status of this entry. The meanings of the values are: learned(3) : the value of the corresponding instance of wfBrSrIpEncapsRing was learned, and is being used.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER learned(3)  

wfBrSrTrafficFilterTable 1.3.6.1.4.1.18.3.5.1.1.2.6
SR Bridge Traffic Filters
Status: mandatory Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    WfBrSrTrafficFilterEntry

wfBrSrTrafficFilterEntry 1.3.6.1.4.1.18.3.5.1.1.2.6.1
An entry in WfBrSrTrafficFilterTable.
Status: mandatory Access: not-accessible
OBJECT-TYPE    
  WfBrSrTrafficFilterEntry  

wfBrSrTrafficFilterCreate 1.3.6.1.4.1.18.3.5.1.1.2.6.1.1
Defines the existence of the traffic filter rule: created - traffic filter exists delete - traffic filter does not exist and can be deleted.
Status: mandatory Access: read-write
OBJECT-TYPE    
  INTEGER created(1), deleted(2)  

wfBrSrTrafficFilterEnable 1.3.6.1.4.1.18.3.5.1.1.2.6.1.2
Defines whether or not the traffic filter rule should be used: enabled - activate the rule. disabled - inactivate the rule.
Status: mandatory Access: read-write
OBJECT-TYPE    
  INTEGER enabled(1), disabled(2)  

wfBrSrTrafficFilterStatus 1.3.6.1.4.1.18.3.5.1.1.2.6.1.3
Defines the current status of the traffic filter: inactive - the rule is not in use. active - the rule is being used. error - the application detected an error in the rule.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER active(1), error(2), inactive(3)  

wfBrSrTrafficFilterCounter 1.3.6.1.4.1.18.3.5.1.1.2.6.1.4
The number of received packets that have matched this rule.
Status: mandatory Access: read-only
OBJECT-TYPE    
  Counter  

wfBrSrTrafficFilterDefinition 1.3.6.1.4.1.18.3.5.1.1.2.6.1.5
The filter rule definition.
Status: mandatory Access: read-write
OBJECT-TYPE    
  OCTET STRING  

wfBrSrTrafficFilterReserved 1.3.6.1.4.1.18.3.5.1.1.2.6.1.6
Reserved field.
Status: mandatory Access: not-accessible
OBJECT-TYPE    
  INTEGER  

wfBrSrTrafficFilterCircuit 1.3.6.1.4.1.18.3.5.1.1.2.6.1.7
The ID of the Bridge Circuit to which the filter is applied.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER  

wfBrSrTrafficFilterRuleNumber 1.3.6.1.4.1.18.3.5.1.1.2.6.1.8
ID for the rule.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER  

wfBrSrTrafficFilterFragment 1.3.6.1.4.1.18.3.5.1.1.2.6.1.9
Fragment number - for large rules.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER  

wfBrSrEsRifTable 1.3.6.1.4.1.18.3.5.1.1.2.7
A table that contains the currently active RIFs in use by Router End Station Support inst_id[9] = wfBrSrIpExplorerAddress
Status: mandatory Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    WfBrSrEsRifEntry

wfBrSrEsRifEntry 1.3.6.1.4.1.18.3.5.1.1.2.7.1
An entry in wfBrSrEsRif.
Status: mandatory Access: not-accessible
OBJECT-TYPE    
  WfBrSrEsRifEntry  

wfBrSrEsRifCircuit 1.3.6.1.4.1.18.3.5.1.1.2.7.1.1
The circuit on which this entry was learned
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER  

wfBrSrEsRifProtocol 1.3.6.1.4.1.18.3.5.1.1.2.7.1.2
protocol type.
Status: mandatory Access: read-only
OBJECT-TYPE    
  OCTET STRING  

wfBrSrEsRifMacAddr 1.3.6.1.4.1.18.3.5.1.1.2.7.1.3
to this RIF.
Status: mandatory Access: read-only
OBJECT-TYPE    
  OCTET STRING  

wfBrSrEsRifRoute 1.3.6.1.4.1.18.3.5.1.1.2.7.1.4
The route contained in the RIF field
Status: mandatory Access: read-only
OBJECT-TYPE    
  OCTET STRING  

wfSyncTable 1.3.6.1.4.1.18.3.4.5
SYNC line record
Status: mandatory Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    WfSyncEntry

wfSyncEntry 1.3.6.1.4.1.18.3.4.5.1
An entry in the SYNC table
Status: mandatory Access: not-accessible
OBJECT-TYPE    
  WfSyncEntry  

wfSyncDelete 1.3.6.1.4.1.18.3.4.5.1.1
Create/Delete parameter
Status: mandatory Access: read-write
OBJECT-TYPE    
  INTEGER created(1), deleted(2)  

wfSyncDisable 1.3.6.1.4.1.18.3.4.5.1.2
Enable/Disable parameter
Status: mandatory Access: read-write
OBJECT-TYPE    
  INTEGER enabled(1), disabled(2)  

wfSyncState 1.3.6.1.4.1.18.3.4.5.1.3
Line Driver state variable, Not Present, Init, Down, Up
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER up(1), down(2), init(3), wait(4), notpresent(5)  

wfSyncSlot 1.3.6.1.4.1.18.3.4.5.1.4
Instance ID Slot, filled in by driver
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER minimum(1), maximum(14)  

wfSyncConnector 1.3.6.1.4.1.18.3.4.5.1.5
Instance ID Connector, filled in by driver
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER one(1), two(2), three(3), four(4)  

wfSyncCct 1.3.6.1.4.1.18.3.4.5.1.6
CCT number for this line instance
Status: mandatory Access: read-write
OBJECT-TYPE    
  INTEGER minimum(1), maximum(1023)  

wfSyncBofl 1.3.6.1.4.1.18.3.4.5.1.7
breath of life parameter
Status: mandatory Access: read-write
OBJECT-TYPE    
  INTEGER enabled(1), disabled(2)  

wfSyncBoflTmo 1.3.6.1.4.1.18.3.4.5.1.8
breath of life timeout in seconds
Status: mandatory Access: read-write
OBJECT-TYPE    
  INTEGER minimum(1), maximum(60), default(5)  

wfSyncMtu 1.3.6.1.4.1.18.3.4.5.1.9
MTU parameter, this is buffer size for SYNC media, fixed
Status: mandatory Access: read-write
OBJECT-TYPE    
  INTEGER minimum(3), maximum(4500), default(1600)  

wfSyncMadr 1.3.6.1.4.1.18.3.4.5.1.10
Line MAC address, fixed - line driver fills in from the 48 bit address stored in the serial number prom for this connector.
Status: mandatory Access: read-only
OBJECT-TYPE    
  OCTET STRING  

wfSyncPromiscuous 1.3.6.1.4.1.18.3.4.5.1.11
The promiscuous parameter allows address filtering based on the local and remote addresses. When enabled, all frames are received, disabled indicates only frames destined for this local address are received
Status: mandatory Access: read-write
OBJECT-TYPE    
  INTEGER enabled(1), disabled(2)  

wfSyncXid 1.3.6.1.4.1.18.3.4.5.1.12
XID enable/disable parameter. This parameter is used to enable or disable transmission/reception of Test XID frames.
Status: mandatory Access: read-write
OBJECT-TYPE    
  INTEGER enabled(1), disabled(2)  

wfSyncClkSource 1.3.6.1.4.1.18.3.4.5.1.13
Tx/Rx clock source is either internally or external generated.
Status: mandatory Access: read-write
OBJECT-TYPE    
  INTEGER internal(1), external(2)  

wfSyncClkSpeed 1.3.6.1.4.1.18.3.4.5.1.14
Tx/Rx clock speed. This speed selection is valid only when the internal clock speed parameter has been selected.
Status: mandatory Access: read-write
OBJECT-TYPE    
  INTEGER clk1200b(1200), clk2400b(2401), clk4800b(4807), clk7200b(7204), clk9600b(9615), clk19200b(19230), clk32000b(32051), clk38400b(38461), clk56k(56818), clk64k(64102), clk125k(125000), clk230k(227272), clk420k(416666), clk625k(625000), clk833k(833333), clk1mb(1250000), clk2mb(2500000), clk5mb(5000000)  

wfSyncSignalMode 1.3.6.1.4.1.18.3.4.5.1.15
The signal mode parameter indicates the line paramter balanced or unbalanced.
Status: mandatory Access: read-write
OBJECT-TYPE    
  INTEGER balanced(1), unbalanced(2)  

wfSyncRtsEnable 1.3.6.1.4.1.18.3.4.5.1.16
The RTS parameter enables/disables detection of RTS signals on the interface. Normal default mode is running without RTS enabled.
Status: mandatory Access: read-write
OBJECT-TYPE    
  INTEGER enabled(1), disabled(2)  

wfSyncBurstCount 1.3.6.1.4.1.18.3.4.5.1.17
Allows single or multiple DMA burst cycles. When enabled the chip performs 8 word burst's. Single word cycles are performed when disabled
Status: mandatory Access: read-write
OBJECT-TYPE    
  INTEGER enabled(1), disabled(2)  

wfSyncService 1.3.6.1.4.1.18.3.4.5.1.18
Service type for this circuit. Transparent is raw HDLC mode, LLC1 will prefix the HDLC address and control fields to the frame. The LLC2 service provides the LAPB protocol service.
Status: mandatory Access: read-write
OBJECT-TYPE    
  INTEGER transparent(1), llc1(2), llc2(3)  

wfSyncRetryCount 1.3.6.1.4.1.18.3.4.5.1.19
The Retry count parameter indicates the number of retransmission attempts which will be tried per frame before a line is determined to be down. The retry count is max attempts following expiration of the T1 timer. This parameter is equal to the N2 counter in ICB.
Status: mandatory Access: read-write
OBJECT-TYPE    
  INTEGER minimum(1), maximum(64), default(16)  

wfSyncLinkIdleTimer 1.3.6.1.4.1.18.3.4.5.1.20
The link idle parameter is the number of seconds before a line has been determined to be idle. An idle line is considered disconnectd This value is expressed in seconds.
Status: mandatory Access: read-write
OBJECT-TYPE    
  INTEGER minimum(1), maximum(9999), default(3)  

wfSyncRetryTimer 1.3.6.1.4.1.18.3.4.5.1.21
The Retry Timer parameter indicates the timeout in seconds for a response to be heard form the link. Link control frames are sent at the expiration of this timer value. The frames will be resent up to retry count (N2) at which time the link will be disconnected.
Status: mandatory Access: read-write
OBJECT-TYPE    
  INTEGER minimum(1), maximum(9999), default(3)  

wfSyncExtendedAddress 1.3.6.1.4.1.18.3.4.5.1.22
This parameter controls length determination of the address field. When this parameter is enabled, the first bit of the address field be tested to determine the length of address field in octets.
Status: mandatory Access: read-write
OBJECT-TYPE    
  INTEGER enabled(1), disabled(2)  

wfSyncExtendedAddressForce 1.3.6.1.4.1.18.3.4.5.1.23
When this parameter is enabled, the receiver will assume that all address fields are 2 octets in length regardless of the first two bits of the control field. Usefull only in Transparent Mode.
Status: mandatory Access: read-write
OBJECT-TYPE    
  INTEGER enabled(1), disabled(2)  

wfSyncExtendedControl 1.3.6.1.4.1.18.3.4.5.1.24
This parameter allows the control fields of all S and I frames to become 2 octets in length instead of one. Numbering of all I frame become modulo 128 instead of modulo 8. The control field of U frames remains one octet in length.
Status: mandatory Access: read-write
OBJECT-TYPE    
  INTEGER enabled(1), disabled(2)  

wfSyncExtendedControlForce 1.3.6.1.4.1.18.3.4.5.1.25
This parameter when enabled will force all control fields to become two octets in length regardless the first two bits in the control field. Usefull only in Transparent Mode. (LLC1)
Status: mandatory Access: read-write
OBJECT-TYPE    
  INTEGER enabled(1), disabled(2)  

wfSyncConnectAttempts 1.3.6.1.4.1.18.3.4.5.1.26
This parameter controls the number of connection attempts which will be made during a LAPB connection request. This parameter is applicable only during LLC2 service.
Status: mandatory Access: read-write
OBJECT-TYPE    
  INTEGER minimum(1), maximum(9999), default(10)  

wfSyncWindowSizeTx 1.3.6.1.4.1.18.3.4.5.1.27
The window size parameter controls the number of I frames which may be transmitted without acknowledgement. Non EXTC mode.
Status: mandatory Access: read-write
OBJECT-TYPE    
  INTEGER minimum(1), maximum(7), default(1)  

wfSyncWindowSizeTxExtc 1.3.6.1.4.1.18.3.4.5.1.28
The window size parameter controls the number of I frames which may be transmitted without acknowledgement in EXTC mode.
Status: mandatory Access: read-write
OBJECT-TYPE    
  INTEGER minimum(1), maximum(7), default(1)  

wfSyncMinFrameSpace 1.3.6.1.4.1.18.3.4.5.1.29
The minimum frame spacing parameter defines the number of flags that are transmitted between adjacent frames.
Status: mandatory Access: read-write
OBJECT-TYPE    
  INTEGER minimum(1), maximum(32), default(1)  

wfSyncLocalAddress 1.3.6.1.4.1.18.3.4.5.1.30
The local address parameter contains the DTE,DCE or EXPLICIT value expressed as a single octet. It may be extended to 2 octets if EXTA has been set.
Status: mandatory Access: read-write
OBJECT-TYPE    
  INTEGER addressdte(1), addressdce(3), addressexplicit(7)  

wfSyncRemoteAddress 1.3.6.1.4.1.18.3.4.5.1.31
The remote address parameter contains the DTE,DCE or EXPLICIT value expressed as a single octet. It may be extended to 2 octets if EXTA has been set.
Status: mandatory Access: read-write
OBJECT-TYPE    
  INTEGER addressdte(1), addressdce(3), addressexplicit(7)  

wfSyncPassThruLocalMadr 1.3.6.1.4.1.18.3.4.5.1.32
48 bit MAC address of Local end of Sync Passthru circuit
Status: mandatory Access: read-write
OBJECT-TYPE    
  OCTET STRING  

wfSyncPassThruRemoteMadr 1.3.6.1.4.1.18.3.4.5.1.33
48 bit MAC address of Remote end of Sync Passthru circuit
Status: mandatory Access: read-write
OBJECT-TYPE    
  OCTET STRING  

wfSyncWanProtocol 1.3.6.1.4.1.18.3.4.5.1.34
WAN protocol selection is provided via this parameter. The supported protocols can be selected per interface.
Status: mandatory Access: read-write
OBJECT-TYPE    
  INTEGER standard(1), passthru(2), ppp(3), smds(4), framerelay(5)  

wfSyncCrcSize 1.3.6.1.4.1.18.3.4.5.1.35
CRC size parameter, 16 bit standard CCITT or extended 32 bit CRC
Status: mandatory Access: read-write
OBJECT-TYPE    
  INTEGER crc16bit(1), crc32bit(2)  

wfSyncRxOctets 1.3.6.1.4.1.18.3.4.5.1.36
Number of octets received without error
Status: mandatory Access: read-only
OBJECT-TYPE    
  Counter  

wfSyncRxFrames 1.3.6.1.4.1.18.3.4.5.1.37
Number of frames received without error
Status: mandatory Access: read-only
OBJECT-TYPE    
  Counter  

wfSyncTxOctets 1.3.6.1.4.1.18.3.4.5.1.38
Number of octets transmitted without error
Status: mandatory Access: read-only
OBJECT-TYPE    
  Counter  

wfSyncTxFrames 1.3.6.1.4.1.18.3.4.5.1.39
Number of frames transmitted without error
Status: mandatory Access: read-only
OBJECT-TYPE    
  Counter  

wfSyncRxErrors 1.3.6.1.4.1.18.3.4.5.1.40
Number of receive errors
Status: mandatory Access: read-only
OBJECT-TYPE    
  Counter  

wfSyncTxErrors 1.3.6.1.4.1.18.3.4.5.1.41
Number of transmission errors
Status: mandatory Access: read-only
OBJECT-TYPE    
  Counter  

wfSyncLackRescRx 1.3.6.1.4.1.18.3.4.5.1.42
Number of Rx frames dropped due to lack of buffer resources
Status: mandatory Access: read-only
OBJECT-TYPE    
  Counter  

wfSyncLackRescTx 1.3.6.1.4.1.18.3.4.5.1.43
Number of Tx frames dropped due to lack of buffer resources
Status: mandatory Access: read-only
OBJECT-TYPE    
  Counter  

wfSyncUnderFlowTx 1.3.6.1.4.1.18.3.4.5.1.44
Number of transmission underflows, device FIFO went empty before next DMA request was granted.
Status: mandatory Access: read-only
OBJECT-TYPE    
  Counter  

wfSyncRejectsTx 1.3.6.1.4.1.18.3.4.5.1.45
Number of reject frames which were transmitted
Status: mandatory Access: read-only
OBJECT-TYPE    
  Counter  

wfSyncRejectsRx 1.3.6.1.4.1.18.3.4.5.1.46
Number of reject frames which were received
Status: mandatory Access: read-only
OBJECT-TYPE    
  Counter  

wfSyncOverFlowRx 1.3.6.1.4.1.18.3.4.5.1.47
Number of receive overflows, device FIFO overflowed before next DMA cycle granted. No buffer resources available.
Status: mandatory Access: read-only
OBJECT-TYPE    
  Counter  

wfSyncFramesIncompRx 1.3.6.1.4.1.18.3.4.5.1.48
Number of frames which were incompletely received. These are frames which may have resulted from FRMRR errors.
Status: mandatory Access: read-only
OBJECT-TYPE    
  Counter  

wfSyncBadFramesRx 1.3.6.1.4.1.18.3.4.5.1.49
Number of bad receive frames, caused by FCS errors or non octet aligned.
Status: mandatory Access: read-only
OBJECT-TYPE    
  Counter  

wfSyncFrameRejectsRx 1.3.6.1.4.1.18.3.4.5.1.50
Number of Frame Rejects received
Status: mandatory Access: read-only
OBJECT-TYPE    
  Counter  

wfSyncRuntsRx 1.3.6.1.4.1.18.3.4.5.1.51
Number of runt frames received
Status: mandatory Access: read-only
OBJECT-TYPE    
  Counter  

wfSyncT1Timeouts 1.3.6.1.4.1.18.3.4.5.1.52
Number of T1 timeout's detected. The T1 timer is the link retransmission timer. Link control frames will be retransmitted when T1 expires. This is a count of the number of timeouts.
Status: mandatory Access: read-only
OBJECT-TYPE    
  Counter  

wfSyncMemoryErrors 1.3.6.1.4.1.18.3.4.5.1.53
Number of memory access errors detected. A MERR is the expiration of a DMA cycle without the bus being granted within 26us.
Status: mandatory Access: read-only
OBJECT-TYPE    
  Counter  

wfSyncMediaType 1.3.6.1.4.1.18.3.4.5.1.54
Media type selection is provided via this parameter
Status: mandatory Access: read-write
OBJECT-TYPE    
  INTEGER default(1), t1(2), e1(3)  

wfSys 1.3.6.1.4.1.18.3.3.1
OBJECT IDENTIFIER    

wfSysDescr 1.3.6.1.4.1.18.3.3.1.1
A textual description of the entity including full name and version of the system's hardware type, OS, and networking SW
Status: mandatory Access: read-only
OBJECT-TYPE    
  DisplayString  

wfSysObjectID 1.3.6.1.4.1.18.3.3.1.2
Provides an unambiguous means for determining the MIB type (old product vs. harpoon MIB).
Status: mandatory Access: read-only
OBJECT-TYPE    
  OBJECT IDENTIFIER  

wfSysUpTime 1.3.6.1.4.1.18.3.3.1.3
Time in seconds/100 since the last cold start
Status: mandatory Access: read-only
OBJECT-TYPE    
  TimeTicks  

wfSysContact 1.3.6.1.4.1.18.3.3.1.4
Contact person for this node and where/how to contact them
Status: mandatory Access: read-write
OBJECT-TYPE    
  DisplayString  

wfSysName 1.3.6.1.4.1.18.3.3.1.5
Node's fully qualified domain name or administratively assigned name
Status: mandatory Access: read-write
OBJECT-TYPE    
  DisplayString  

wfSysLocation 1.3.6.1.4.1.18.3.3.1.6
Physical Location of this Node
Status: mandatory Access: read-write
OBJECT-TYPE    
  DisplayString  

wfSysServices 1.3.6.1.4.1.18.3.3.1.7
A sum of numbers indicating the set of services the entity offers. For each layer L, add 2**(L - 1). Example: 78 = Layers 2,3,4, and 7.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER  

wfSysGmtOffset 1.3.6.1.4.1.18.3.3.1.8
The positive or negative offset from Greenwich Mean Time (GMT). This effectively describes the time zone.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER  

wfSysMibVersion 1.3.6.1.4.1.18.3.3.1.9
The version of the private management information base currently being used by the system software. Format is: xV.RR
Status: mandatory Access: read-only
OBJECT-TYPE    
  DisplayString  

wfT1Table 1.3.6.1.4.1.18.3.4.10
T1 line record
Status: mandatory Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    WfT1Entry

wfT1Entry 1.3.6.1.4.1.18.3.4.10.1
An entry in the T1 table
Status: mandatory Access: not-accessible
OBJECT-TYPE    
  WfT1Entry  

wfT1Delete 1.3.6.1.4.1.18.3.4.10.1.1
create/delete parameter, dflt = created
Status: mandatory Access: read-write
OBJECT-TYPE    
  INTEGER created(1), deleted(2)  

wfT1Disable 1.3.6.1.4.1.18.3.4.10.1.2
enable/disable parameter, dflt = enabled
Status: mandatory Access: read-write
OBJECT-TYPE    
  INTEGER enabled(1), disabled(2)  

wfT1State 1.3.6.1.4.1.18.3.4.10.1.3
line driver state variable, Not Present, Init, Up
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER up(1), init(3), notpresent(4)  

wfT1Slot 1.3.6.1.4.1.18.3.4.10.1.4
instance ID Slot, filled in by driver
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER minimum(1), maximum(14)  

wfT1Connector 1.3.6.1.4.1.18.3.4.10.1.5
instance ID Connector, filled in by driver
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER one(1), two(2)  

wfT1Madr 1.3.6.1.4.1.18.3.4.10.1.6
Line mac address, filled in by driver
Status: mandatory Access: read-only
OBJECT-TYPE    
  OCTET STRING  

wfT1FrameType 1.3.6.1.4.1.18.3.4.10.1.7
Frame Type - differentiates between two tarrifed framing formats D4 and ESF.
Status: mandatory Access: read-write
OBJECT-TYPE    
  INTEGER d4(1), esf(2)  

wfT1LineBuildout 1.3.6.1.4.1.18.3.4.10.1.8
Line Buildout - Approximate length of cable
Status: mandatory Access: read-write
OBJECT-TYPE    
  INTEGER minimum(1), maximum(655), default(1)  

wfT1B8ZSSupport 1.3.6.1.4.1.18.3.4.10.1.9
B8ZS Support - Enables or disables Binary 8 zeros suppression
Status: mandatory Access: read-write
OBJECT-TYPE    
  INTEGER enabled(1), disabled(2)  

wfT1ClockMode 1.3.6.1.4.1.18.3.4.10.1.10
Clock Mode - Specifies the source of the T1 transmit clock
Status: mandatory Access: read-write
OBJECT-TYPE    
  INTEGER internal(1), slave(2), manual(4), default(1)  

wfT1MiniDacs 1.3.6.1.4.1.18.3.4.10.1.11
MiniDacs Configuration - assigns each T1 channel to a specific function
Status: mandatory Access: read-write
OBJECT-TYPE    
  DisplayString  

wfT1BipolarVios 1.3.6.1.4.1.18.3.4.10.1.12
Number of Bipolar Violations
Status: mandatory Access: read-only
OBJECT-TYPE    
  Counter  

wfT1FrameBitErrs 1.3.6.1.4.1.18.3.4.10.1.13
Number of frame bit errors
Status: mandatory Access: read-only
OBJECT-TYPE    
  Counter  

wfT1OutOfFrameErrs 1.3.6.1.4.1.18.3.4.10.1.14
Number of Out of Frame errors
Status: mandatory Access: read-only
OBJECT-TYPE    
  Counter  

wfT1SuperFrameErrs 1.3.6.1.4.1.18.3.4.10.1.15
Number of Superframe errors
Status: mandatory Access: read-only
OBJECT-TYPE    
  Counter  

wfT1RcvYelAlarms 1.3.6.1.4.1.18.3.4.10.1.16
Number of Yellow Alarms Received
Status: mandatory Access: read-only
OBJECT-TYPE    
  Counter  

wfT1RcvCarrierLoss 1.3.6.1.4.1.18.3.4.10.1.17
Number of instances of carrier loss
Status: mandatory Access: read-only
OBJECT-TYPE    
  Counter  

wfT1RcvRedAlarms 1.3.6.1.4.1.18.3.4.10.1.18
Number of Red Alarm Received
Status: mandatory Access: read-only
OBJECT-TYPE    
  Counter  

wfTftp 1.3.6.1.4.1.18.3.5.3.6
OBJECT IDENTIFIER    

wfTftpDisable 1.3.6.1.4.1.18.3.5.3.6.1
Enables or Disables TFTP Subsystem
Status: mandatory Access: read-write
OBJECT-TYPE    
  INTEGER enabled(1), disabled(2)  

wfTftpDefaultVolume 1.3.6.1.4.1.18.3.5.3.6.2
The file system volume number to which transferred files will be written and from which they will be retrieved. The volume number corresponds to the slot number on which the volume resides. Slot 1 is reserved for SRM.
Status: mandatory Access: read-write
OBJECT-TYPE    
  INTEGER minimum(2), default(2), maximum(14)  

wfTftpXfers 1.3.6.1.4.1.18.3.5.3.6.3
Number of Transfers in Progress
Status: mandatory Access: read-only
OBJECT-TYPE    
  Counter  

wfTftpTimeOut 1.3.6.1.4.1.18.3.5.3.6.4
General Retransmission time-out value (seconds)
Status: mandatory Access: read-write
OBJECT-TYPE    
  INTEGER  

wfTftpCloseTimeOut 1.3.6.1.4.1.18.3.5.3.6.5
Retransmission time-out value for sender of final ACK (seconds)
Status: mandatory Access: read-write
OBJECT-TYPE    
  INTEGER  

wfTftpRexmit 1.3.6.1.4.1.18.3.5.3.6.6
Maximum Number of Retransmissions
Status: mandatory Access: read-write
OBJECT-TYPE    
  INTEGER  

wfTftpInFiles 1.3.6.1.4.1.18.3.5.3.6.7
Number of files Successfully received
Status: mandatory Access: read-only
OBJECT-TYPE    
  Counter  

wfTftpOutFiles 1.3.6.1.4.1.18.3.5.3.6.8
Number of files Successfully sent
Status: mandatory Access: read-only
OBJECT-TYPE    
  Counter  

wfTftpInWRQ 1.3.6.1.4.1.18.3.5.3.6.9
Number of write requests received
Status: mandatory Access: read-only
OBJECT-TYPE    
  Counter  

wfTftpOutWRQ 1.3.6.1.4.1.18.3.5.3.6.10
Number of write requests sent
Status: mandatory Access: read-only
OBJECT-TYPE    
  Counter  

wfTftpInRRQ 1.3.6.1.4.1.18.3.5.3.6.11
Number of read requests received
Status: mandatory Access: read-only
OBJECT-TYPE    
  Counter  

wfTftpOutRRQ 1.3.6.1.4.1.18.3.5.3.6.12
Number of read requests sent
Status: mandatory Access: read-only
OBJECT-TYPE    
  Counter  

wfTftpRexmitPkts 1.3.6.1.4.1.18.3.5.3.6.13
Number of Re-transmitted packets
Status: mandatory Access: read-only
OBJECT-TYPE    
  Counter  

wfTftpInErr 1.3.6.1.4.1.18.3.5.3.6.14
Number of Error PDUs Received
Status: mandatory Access: read-only
OBJECT-TYPE    
  Counter  

wfTftpOutErr 1.3.6.1.4.1.18.3.5.3.6.15
Number of Error PDUs Sent
Status: mandatory Access: read-only
OBJECT-TYPE    
  Counter  

wfTftpAborts 1.3.6.1.4.1.18.3.5.3.6.16
Number of Aborted Pseudo Connections
Status: mandatory Access: read-only
OBJECT-TYPE    
  Counter  

wfTiRui 1.3.6.1.4.1.18.3.3.2.2
OBJECT IDENTIFIER    

wfTiRuiState 1.3.6.1.4.1.18.3.3.2.2.1
The state of the ti rui command processor. Idle is normal state. Busy indicates a command is being processed.
Status: optional Access: read-only
OBJECT-TYPE    
  INTEGER idle(1), busy(2)  

wfTiRuiAction 1.3.6.1.4.1.18.3.3.2.2.2
Ti command request string
Status: optional Access: read-write
OBJECT-TYPE    
  DisplayString  

wfTiRuiResult 1.3.6.1.4.1.18.3.3.2.2.3
The result of the Ti command requst
Status: optional Access: read-only
OBJECT-TYPE    
  DisplayString  

wfTiRuiInReqs 1.3.6.1.4.1.18.3.3.2.2.4
Total number of command requests
Status: optional Access: read-only
OBJECT-TYPE    
  Counter  

wfTiRuiOutResults 1.3.6.1.4.1.18.3.3.2.2.5
Total number of command requests that processed without error
Status: optional Access: read-only
OBJECT-TYPE    
  Counter  

wfTiRuiOutResultsErr 1.3.6.1.4.1.18.3.3.2.2.6
Total number of command requests that could not be processed because of errors
Status: optional Access: read-only
OBJECT-TYPE    
  Counter  

wfTokenRingTable 1.3.6.1.4.1.18.3.4.2
TOKEN RING line record
Status: mandatory Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    WfTokenRingEntry

wfTokenRingEntry 1.3.6.1.4.1.18.3.4.2.1
An entry in the token table
Status: mandatory Access: not-accessible
OBJECT-TYPE    
  WfTokenRingEntry  

wfTokenRingDelete 1.3.6.1.4.1.18.3.4.2.1.1
create/delete parameter.
Status: mandatory Access: read-write
OBJECT-TYPE    
  INTEGER created(1), deleted(2)  

wfTokenRingDisable 1.3.6.1.4.1.18.3.4.2.1.2
enable/disable parameter.
Status: mandatory Access: read-write
OBJECT-TYPE    
  INTEGER enabled(1), disabled(2)  

wfTokenRingState 1.3.6.1.4.1.18.3.4.2.1.3
line driver state variable, Not Present, Init, Down, Up
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER up(1), down(2), init(3), notpresent(4)  

wfTokenRingSlot 1.3.6.1.4.1.18.3.4.2.1.4
instance ID Slot, filled in by driver
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER minimum(1), maximum(14)  

wfTokenRingConnector 1.3.6.1.4.1.18.3.4.2.1.5
instance ID Connector, filled in by driver
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER one(1), two(2)  

wfTokenRingCct 1.3.6.1.4.1.18.3.4.2.1.6
cct number for this line instance, configuration required
Status: mandatory Access: read-write
OBJECT-TYPE    
  INTEGER minimum(1), maximum(1023)  

wfTokenRingMtu 1.3.6.1.4.1.18.3.4.2.1.7
mtu parameter, fixed. This mtu of 4568 allows a type 3 Source Route Frame (info=4472) to be IP encapsulated over Token Ring. The components are: AC_FC (2) + SNAP (12+8) + SNAP_IP (12+8+20) + SR (12+18) + TYPE3_INFO (4472) + FCS (4) --------------------- total 4568 bytes
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER default(4568)  

wfTokenRingMadr 1.3.6.1.4.1.18.3.4.2.1.8
line MAC address, line driver fills in the currently used 48 bit MAC address.
Status: mandatory Access: read-only
OBJECT-TYPE    
  OCTET STRING  

wfTokenRingCfgMadr 1.3.6.1.4.1.18.3.4.2.1.9
Configured line MAC address. Only used if wfTokenRingMadrSelect is set appropriately.
Status: mandatory Access: read-write
OBJECT-TYPE    
  OCTET STRING  

wfTokenRingMadrSelect 1.3.6.1.4.1.18.3.4.2.1.10
Selector determines which MAC address the interface will use.
Status: mandatory Access: read-write
OBJECT-TYPE    
  INTEGER boxwide(1), prom(2), cnfg(3)  

wfTokenRingSpeed 1.3.6.1.4.1.18.3.4.2.1.11
Token Ring speed parameter - 4 and 16 Mbps are only valid values
Status: mandatory Access: read-write
OBJECT-TYPE    
  INTEGER mbps4(4194304), mbps16(16777216)  

wfTokenRingEarlyTokenRelease 1.3.6.1.4.1.18.3.4.2.1.12
Early Token Release parameter, only valid with 16Mbps
Status: mandatory Access: read-write
OBJECT-TYPE    
  INTEGER enabled(1), disabled(2)  

wfTokenRingStatus 1.3.6.1.4.1.18.3.4.2.1.13
The current interface status. This attribute is only valid when the wfTokenRingOpenState attribute is set to OPENED. The attribute's value is a sum of values, one for each currently applicable condition (ie, bit positions indicate active conditions). Occurrences of each condition are separately counted and the counts are included in this MIB as attributes wfTokenRingSignalLosses through wfTokenRingRingRecoveries. The following values are defined: 32768 = Signal Losses 16384 = Hard Errors 8192 = Soft Errors 4096 = Transmit Beacons 2048 = Lobe Wire Faults 1024 = Auto-Removal Errors 256 = Remove Received 128 = Counter Overflows 64 = Single Stations 32 = Ring Recoveries This attribute is the most recent sum of these conditions. More information on each condition is include in the descriptions of the individual counter attributes.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER  

wfTokenRingOpenState 1.3.6.1.4.1.18.3.4.2.1.14
The current interface state with respect to entering or leaving the ring.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER opened(1), opening(2), closing(3), openfailure(4), ringfailure(5), closed(6)  

wfTokenRingOpenStatus 1.3.6.1.4.1.18.3.4.2.1.15
Indicates the success, or the reason for failure, of the station's most recent attempt to enter the ring.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER open(1), badparam(2), lobefailed(3), signalloss(4), insertiontimeout(5), ringfailed(6), beaconing(7), duplicatemac(8), requestfailed(9), removereceived(10), unkerror(11), noopen(12)  

wfTokenRingUpStream 1.3.6.1.4.1.18.3.4.2.1.16
MAC address of Up Stream neighbor. Only valid when 'opened'.
Status: mandatory Access: read-only
OBJECT-TYPE    
  OCTET STRING  

wfTokenRingRxOctets 1.3.6.1.4.1.18.3.4.2.1.17
Number of octets received without error.
Status: mandatory Access: read-only
OBJECT-TYPE    
  Counter  

wfTokenRingRxFrames 1.3.6.1.4.1.18.3.4.2.1.18
Number of frames received without error.
Status: mandatory Access: read-only
OBJECT-TYPE    
  Counter  

wfTokenRingTxOctets 1.3.6.1.4.1.18.3.4.2.1.19
Number of octets transmitted without error.
Status: mandatory Access: read-only
OBJECT-TYPE    
  Counter  

wfTokenRingTxFrames 1.3.6.1.4.1.18.3.4.2.1.20
Number of frames transmitted without error.
Status: mandatory Access: read-only
OBJECT-TYPE    
  Counter  

wfTokenRingInDiscards 1.3.6.1.4.1.18.3.4.2.1.21
Number of error-free inbound packets discarded. Usually due to lack of memory resources. This is equivalent to wfTokenRingRxCongestionErrors.
Status: mandatory Access: read-only
OBJECT-TYPE    
  Counter  

wfTokenRingInErrors 1.3.6.1.4.1.18.3.4.2.1.22
Number of inbound packets not delivered to higher-layer protocol due to errors. The sum of wfTokenRingLineErrors and wfTokenRingBurstErrors.
Status: mandatory Access: read-only
OBJECT-TYPE    
  Counter  

wfTokenRingOutDiscards 1.3.6.1.4.1.18.3.4.2.1.23
Number of error-free outbound packets discarded. Usually due to lack of transmission bandwidth. This is equivalent to wfTokenRingTxClipFrames.
Status: mandatory Access: read-only
OBJECT-TYPE    
  Counter  

wfTokenRingOutErrors 1.3.6.1.4.1.18.3.4.2.1.24
Number of outbound packets that could not be transmitted because of errors. This is equivalent to wfTokenRingLostFrameErrors.
Status: mandatory Access: read-only
OBJECT-TYPE    
  Counter  

wfTokenRingTxClipFrames 1.3.6.1.4.1.18.3.4.2.1.25
Number of frames clipped in driver's transmit routine due to transmit congestion.
Status: mandatory Access: read-only
OBJECT-TYPE    
  Counter  

wfTokenRingRxReplenMisses 1.3.6.1.4.1.18.3.4.2.1.26
Number of packet buffer misses while attempting to replenish driver receive ring.
Status: mandatory Access: read-only
OBJECT-TYPE    
  Counter  

wfTokenRingSignalLosses 1.3.6.1.4.1.18.3.4.2.1.27
Number of ring signal losses detected.
Status: mandatory Access: read-only
OBJECT-TYPE    
  Counter  

wfTokenRingHardErrors 1.3.6.1.4.1.18.3.4.2.1.28
Number of events causing the adapter to transmit or receive beacon MAC frames.
Status: mandatory Access: read-only
OBJECT-TYPE    
  Counter  

wfTokenRingSoftErrors 1.3.6.1.4.1.18.3.4.2.1.29
Number of soft errors. Corresponds to the number of Report Error MAC frames transmitted by this station.
Status: mandatory Access: read-only
OBJECT-TYPE    
  Counter  

wfTokenRingTransmitBeacons 1.3.6.1.4.1.18.3.4.2.1.30
Number of events causing the adapter to transmit beacon frames.
Status: mandatory Access: read-only
OBJECT-TYPE    
  Counter  

wfTokenRingLobeWireFaults 1.3.6.1.4.1.18.3.4.2.1.31
Number of opens or shorts (cable faults) between the adapter and the MAU.
Status: mandatory Access: read-only
OBJECT-TYPE    
  Counter  

wfTokenRingAutoRemovalErrors 1.3.6.1.4.1.18.3.4.2.1.32
Number of lobe wrap test failures during beacon auto_removal process.
Status: mandatory Access: read-only
OBJECT-TYPE    
  Counter  

wfTokenRingRequestRemoves 1.3.6.1.4.1.18.3.4.2.1.33
Number of Remove Ring Station MAC frames received. Each frame causes this station to leave the ring.
Status: mandatory Access: read-only
OBJECT-TYPE    
  Counter  

wfTokenRingCounterOverflows 1.3.6.1.4.1.18.3.4.2.1.34
Number of adapter error counter overflows.
Status: mandatory Access: read-only
OBJECT-TYPE    
  Counter  

wfTokenRingSingleStations 1.3.6.1.4.1.18.3.4.2.1.35
Number of ring status change interrupts while adapter is only station on the ring.
Status: mandatory Access: read-only
OBJECT-TYPE    
  Counter  

wfTokenRingRingRecoveries 1.3.6.1.4.1.18.3.4.2.1.36
Number of claim token MAC frames (ring recoveries) observed on the ring.
Status: mandatory Access: read-only
OBJECT-TYPE    
  Counter  

wfTokenRingAdapterChecks 1.3.6.1.4.1.18.3.4.2.1.37
Number of internal adapter errors that result in adapter crashes.
Status: mandatory Access: read-only
OBJECT-TYPE    
  Counter  

wfTokenRingFirstAdapterCheckCode 1.3.6.1.4.1.18.3.4.2.1.38
Adapter Check Code of first occurrence.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER  

wfTokenRingLastAdapterCheckCode 1.3.6.1.4.1.18.3.4.2.1.39
Adapter Check Code of most recent (last) occurrence.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER  

wfTokenRingLineErrors 1.3.6.1.4.1.18.3.4.2.1.40
Number of frames copied or repeated by this station with bad format or an FCS error.
Status: mandatory Access: read-only
OBJECT-TYPE    
  Counter  

wfTokenRingBurstErrors 1.3.6.1.4.1.18.3.4.2.1.41
Number of errored frames with no transition for 5 1/2 bit times.
Status: mandatory Access: read-only
OBJECT-TYPE    
  Counter  

wfTokenRingAriFciErrors 1.3.6.1.4.1.18.3.4.2.1.42
Number of occurrences of this station receiving both an AMP MAC frame and a SMP MAC frame with the a & c bits clear or more than one SMP MAC frame with the a & c bits clear without an intervening AMP MAC frame. This condition indicates that the up-stream neighbor is unable to set the a & c bits in a frame that it has copied.
Status: mandatory Access: read-only
OBJECT-TYPE    
  Counter  

wfTokenRingLostFrameErrors 1.3.6.1.4.1.18.3.4.2.1.43
Number of frames being stripped which are missing their tails.
Status: mandatory Access: read-only
OBJECT-TYPE    
  Counter  

wfTokenRingRxCongestionErrors 1.3.6.1.4.1.18.3.4.2.1.44
Number of frames dropped due to receive congestion.
Status: mandatory Access: read-only
OBJECT-TYPE    
  Counter  

wfTokenRingFrameCopiedErrors 1.3.6.1.4.1.18.3.4.2.1.45
Number of specifically addressed frames for this station that had their a & c bits previously set.
Status: mandatory Access: read-only
OBJECT-TYPE    
  Counter  

wfTokenRingTokenErrors 1.3.6.1.4.1.18.3.4.2.1.46
Number of token protocol errors. Only relevant when this station is the active monitor.
Status: mandatory Access: read-only
OBJECT-TYPE    
  Counter  

wfTokenRingDmaBusErrors 1.3.6.1.4.1.18.3.4.2.1.47
Number of bus errors during DMA that do not exceed threshold.
Status: mandatory Access: read-only
OBJECT-TYPE    
  Counter  

wfTokenRingDmaParityErrors 1.3.6.1.4.1.18.3.4.2.1.48
Number of parity errors during DMA that do not exceed threshold.
Status: mandatory Access: read-only
OBJECT-TYPE    
  Counter  

wfTokenRingSrbNotFreeCmdAborts 1.3.6.1.4.1.18.3.4.2.1.49
Number of host to adapter commands aborted because of in-completed in process commands.
Status: mandatory Access: read-only
OBJECT-TYPE    
  Counter  

wfTokenRingRxProcessings 1.3.6.1.4.1.18.3.4.2.1.50
Number of processings of received frames (similar to RINT).
Status: mandatory Access: read-only
OBJECT-TYPE    
  Counter  

wfTokenRingTxProcessings 1.3.6.1.4.1.18.3.4.2.1.51
Number of processings of frames for transmit.
Status: mandatory Access: read-only
OBJECT-TYPE    
  Counter  

wfTokenRingTxCmplProcessings 1.3.6.1.4.1.18.3.4.2.1.52
Number of processings of transmitted frames (similar to TINT).
Status: mandatory Access: read-only
OBJECT-TYPE    
  Counter  

wfTokenRingRxTimeouts 1.3.6.1.4.1.18.3.4.2.1.53
Number of re-initializations due to receiver time-outs.
Status: mandatory Access: read-only
OBJECT-TYPE    
  Counter  

wfTokenRingCmdTimeouts 1.3.6.1.4.1.18.3.4.2.1.54
Number of re-initializations due to command time-outs.
Status: mandatory Access: read-only
OBJECT-TYPE    
  Counter  

wfTokenRingRxHostIntErrors 1.3.6.1.4.1.18.3.4.2.1.55
Number of re-initializations due to receive host interface errors.
Status: mandatory Access: read-only
OBJECT-TYPE    
  Counter  

wfTokenRingRxTxBufferSize 1.3.6.1.4.1.18.3.4.2.1.56
Internal Adapter RAM buffer size.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER  

wfVinesBase 1.3.6.1.4.1.18.3.5.8.1
OBJECT IDENTIFIER    

wfVinesBaseDelete 1.3.6.1.4.1.18.3.5.8.1.1
Create/Delete parameter. This value determines whether or not VINES is configured on this slot.
Status: mandatory Access: read-write
OBJECT-TYPE    
  INTEGER created(1), deleted(2)  

wfVinesBaseDisable 1.3.6.1.4.1.18.3.5.8.1.2
This parameter determines whether or not VINES is to startup.
Status: mandatory Access: read-write
OBJECT-TYPE    
  INTEGER enabled(1), disabled(2)  

wfVinesBaseState 1.3.6.1.4.1.18.3.5.8.1.3
This parameter reflects the current state of VINES.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER up(1), down(2), init(3), notpresent(4)  

wfVinesBaseUserNetid 1.3.6.1.4.1.18.3.5.8.1.4
The network ID as defined by the user. A null value indicates that the user is not configuring a Network ID and that the the router should assign it.
Status: mandatory Access: read-write
OBJECT-TYPE    
  INTEGER minimum(1), maximum(2097151)  

wfVinesBaseRouterNetid 1.3.6.1.4.1.18.3.5.8.1.5
The network ID as defined by the router. If the user configures a Network ID in the above attribute, we will take that value and add in the Wellfleet code for VINES and save it here.
Status: mandatory Access: read-only
OBJECT-TYPE    
  Counter  

wfVinesBaseBcastClass 1.3.6.1.4.1.18.3.5.8.1.6
The broadcast modifier. This value defines the class of broadcast packets that are originated by this node.
Status: mandatory Access: read-write
OBJECT-TYPE    
  INTEGER bcast(1), chrg(2), cost(3), lans(4), srvr(5), nochrg(6), locost(7), alllans(8)  

wfVinesIp 1.3.6.1.4.1.18.3.5.8.2
OBJECT IDENTIFIER    

wfVinesIpTotIn 1.3.6.1.4.1.18.3.5.8.2.1
The total number of VINES IP packets received.
Status: mandatory Access: read-only
OBJECT-TYPE    
  Counter  

wfVinesIpTotOut 1.3.6.1.4.1.18.3.5.8.2.2
The total number of VINES IP packets sent.
Status: mandatory Access: read-only
OBJECT-TYPE    
  Counter  

wfVinesIpBad 1.3.6.1.4.1.18.3.5.8.2.3
The total number of badly formed packets that were received. This field is incremented when a packet is received with an improper checksum.
Status: mandatory Access: read-only
OBJECT-TYPE    
  Counter  

wfVinesIpRouted 1.3.6.1.4.1.18.3.5.8.2.4
The total number of packets received that were routed to another node. This statistic includes the number of IP packets encapsulated within routed VINES IP headers. Each routed packet counts as both an incoming and outgoing packet.
Status: mandatory Access: read-only
OBJECT-TYPE    
  Counter  

wfVinesIpRoutedHWM 1.3.6.1.4.1.18.3.5.8.2.5
The largest number of packets routed in one second since the server was last booted.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER  

wfVinesIpBcast 1.3.6.1.4.1.18.3.5.8.2.6
The number of VINES IP broadcast packets sent, both locally generated and routed from other nodes.
Status: mandatory Access: read-only
OBJECT-TYPE    
  Counter  

wfVinesIpBcastHWM 1.3.6.1.4.1.18.3.5.8.2.7
The largest number of packets broadcast in one second since the server was last booted.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER  

wfVinesIpReass 1.3.6.1.4.1.18.3.5.8.2.8
The number of times that packets were reassembled. Reassemblies result from the transmission of packets that must be broken into smaller pieces, then reassembled due to differences in transmission media.
Status: mandatory Access: read-only
OBJECT-TYPE    
  Counter  

wfVinesIpFrags 1.3.6.1.4.1.18.3.5.8.2.9
The number of packet fragmentations performed.
Status: mandatory Access: read-only
OBJECT-TYPE    
  Counter  

wfVinesIpToDodIP 1.3.6.1.4.1.18.3.5.8.2.10
The number of packets that VINES IP passed to IP for encapsulation in IP headers. These packets were initially handled by VINES IP, but were passed to IP for routing. If the TCP/IP Server-to-Server option is not installed, this value will be zero.
Status: mandatory Access: read-only
OBJECT-TYPE    
  Counter  

wfVinesIpFromDodIP 1.3.6.1.4.1.18.3.5.8.2.11
The number of packets that VINES IP received from IP to be decapsulated into VINES packets. IP initially handled these packets, but had to pass them on to VINES IP for routing. If the server is not running a TCP/IP option, this value will be zero.
Status: mandatory Access: read-only
OBJECT-TYPE    
  Counter  

wfVinesRtpNbr 1.3.6.1.4.1.18.3.5.8.3
OBJECT IDENTIFIER    

wfVinesRtpNbrNumber 1.3.6.1.4.1.18.3.5.8.3.1
Number of entries in the Table of Neighbors.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER  

wfVinesRtpNbrTable 1.3.6.1.4.1.18.3.5.8.4
This is the Table of Neighbors.
Status: mandatory Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    WfVinesRtpNbrEntry

wfVinesRtpNbrEntry 1.3.6.1.4.1.18.3.5.8.4.1
An entry in the Table of Neighbors.
Status: mandatory Access: not-accessible
OBJECT-TYPE    
  WfVinesRtpNbrEntry  

wfVinesRtpNbrNetId 1.3.6.1.4.1.18.3.5.8.4.1.1
The network ID of this neighbor.
Status: mandatory Access: read-only
OBJECT-TYPE    
  Counter  

wfVinesRtpNbrSubNetId 1.3.6.1.4.1.18.3.5.8.4.1.2
The subnetwork ID of this neighbor.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER  

wfVinesRtpNbrType 1.3.6.1.4.1.18.3.5.8.4.1.3
The type of node: client or server.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER workst(1), server(2)  

wfVinesRtpNbrIfType 1.3.6.1.4.1.18.3.5.8.4.1.4
This describes the type of interface.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER enet(1), tr4k(2), tr16k(3), hdlc1200(4), hdlc4800(5), hdlc9600(6), hdlc56000(7), async1200(8), async4800(9), async9600(10), async56000(11), x251200(12), x254800(13), x259600(14), x2556000(15), t145k(16), t1128k(17), t1192k(18), t1256k(19), t1320k(20), t1384k(21), t1448k(22), t1512k(23), t1576k(24), t1640k(25), t1704k(26), t1896k(27), t11088k(28), t11344k(29), tunnel(30), fddi(31)  

wfVinesRtpNbrRemAdr 1.3.6.1.4.1.18.3.5.8.4.1.5
Remote MAC address.
Status: mandatory Access: read-only
OBJECT-TYPE    
  OCTET STRING  

wfVinesRtpNbrLocAdr 1.3.6.1.4.1.18.3.5.8.4.1.6
Local MAC address.
Status: mandatory Access: read-only
OBJECT-TYPE    
  OCTET STRING  

wfVinesRtpNbrLocSlot 1.3.6.1.4.1.18.3.5.8.4.1.7
Slot connected to this neighbor.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER  

wfVinesRtpNbrLocLine 1.3.6.1.4.1.18.3.5.8.4.1.8
Line connected to this neighbor.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER  

wfVinesRtpNbrSvrName 1.3.6.1.4.1.18.3.5.8.4.1.9
Name of the server (N/A).
Status: mandatory Access: read-only
OBJECT-TYPE    
  OCTET STRING  

wfVinesRtpNbrCost 1.3.6.1.4.1.18.3.5.8.4.1.10
Cost for this neighbor.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER  

wfVinesRtpRt 1.3.6.1.4.1.18.3.5.8.5
OBJECT IDENTIFIER    

wfVinesRtpRtNumber 1.3.6.1.4.1.18.3.5.8.5.1
Number of entries in the Table of Networks.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER  

wfVinesRtpRtTable 1.3.6.1.4.1.18.3.5.8.6
This is the Table of Networks.
Status: mandatory Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    WfVinesRtpRtEntry

wfVinesRtpRtEntry 1.3.6.1.4.1.18.3.5.8.6.1
An entry in the Table of Networks.
Status: mandatory Access: not-accessible
OBJECT-TYPE    
  WfVinesRtpRtEntry  

wfVinesRtpRtNetid 1.3.6.1.4.1.18.3.5.8.6.1.1
The network ID number.
Status: mandatory Access: read-only
OBJECT-TYPE    
  Counter  

wfVinesRtpRtMetric 1.3.6.1.4.1.18.3.5.8.6.1.2
The routing metric to get to this network.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER  

wfVinesRtpRtIdle 1.3.6.1.4.1.18.3.5.8.6.1.3
The idle time for this network.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER  

wfVinesRtpRtGateNetid 1.3.6.1.4.1.18.3.5.8.6.1.4
The network ID of the gateway to this network.
Status: mandatory Access: read-only
OBJECT-TYPE    
  Counter  

wfVinesRtpRtSvrName 1.3.6.1.4.1.18.3.5.8.6.1.5
The servers name (N/A).
Status: mandatory Access: read-only
OBJECT-TYPE    
  OCTET STRING  

wfVinesRtpRtGateSvrName 1.3.6.1.4.1.18.3.5.8.6.1.6
The name of the gateway server.
Status: mandatory Access: read-only
OBJECT-TYPE    
  OCTET STRING  

wfVinesIf 1.3.6.1.4.1.18.3.5.8.7
OBJECT IDENTIFIER    

wfVinesIfNumber 1.3.6.1.4.1.18.3.5.8.7.1
This is the number of entries in the Interfaces Table.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER  

wfVinesIfTable 1.3.6.1.4.1.18.3.5.8.8
This is the Table of Interfaces.
Status: mandatory Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    WfVinesIfEntry

wfVinesIfEntry 1.3.6.1.4.1.18.3.5.8.8.1
An entry to the Interface Table.
Status: mandatory Access: not-accessible
OBJECT-TYPE    
  WfVinesIfEntry  

wfVinesIfDelete 1.3.6.1.4.1.18.3.5.8.8.1.1
Create/Delete parameter. Users perform an SNMP set command to create/delete a VINES interface.
Status: mandatory Access: read-write
OBJECT-TYPE    
  INTEGER created(1), deleted(2)  

wfVinesIfDisable 1.3.6.1.4.1.18.3.5.8.8.1.2
Enable/Disable parameter. Users perform an SNMP set command to enable/disable a VINES interface.
Status: mandatory Access: read-write
OBJECT-TYPE    
  INTEGER enabled(1), disabled(2)  

wfVinesIfState 1.3.6.1.4.1.18.3.5.8.8.1.3
This parameter reflects the current state of the VINES interface.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER up(1), down(2), init(3), notpresent(4)  

wfVinesIfSlot 1.3.6.1.4.1.18.3.5.8.8.1.4
The slot on which this interface is configured.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER  

wfVinesIfLine 1.3.6.1.4.1.18.3.5.8.8.1.5
The line on which this interface is configured.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER  

wfVinesIfCct 1.3.6.1.4.1.18.3.5.8.8.1.6
The circuit number for this interface.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER  

wfVinesIfSession 1.3.6.1.4.1.18.3.5.8.8.1.7
The session number for this interface.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER  

wfVinesIfType 1.3.6.1.4.1.18.3.5.8.8.1.8
The type of interface this is.
Status: mandatory Access: read-write
OBJECT-TYPE    
  INTEGER enet(1), tr4k(2), tr16k(3), hdlc1200(4), hdlc4800(5), hdlc9600(6), hdlc56000(7), async1200(8), async4800(9), async9600(10), async56000(11), x251200(12), x254800(13), x259600(14), x2556000(15), t145k(16), t1128k(17), t1192k(18), t1256k(19), t1320k(20), t1384k(21), t1448k(22), t1512k(23), t1576k(24), t1640k(25), t1704k(26), t1896k(27), t11088k(28), t11344k(29), tunnel(30), fddi(31)  

wfVinesIfDescr 1.3.6.1.4.1.18.3.5.8.8.1.9
Description of this interface.
Status: mandatory Access: read-only
OBJECT-TYPE    
  OCTET STRING  

wfVinesIfAdr 1.3.6.1.4.1.18.3.5.8.8.1.10
The MAC address of this interface.
Status: mandatory Access: read-only
OBJECT-TYPE    
  OCTET STRING  

wfVinesIfDodIpDisable 1.3.6.1.4.1.18.3.5.8.8.1.11
This parameter indicates if this interface is enabled to encapsulate VINES packets over DoD IP.
Status: mandatory Access: read-write
OBJECT-TYPE    
  INTEGER enabled(1), disabled(2)  

wfVinesIfArpDisable 1.3.6.1.4.1.18.3.5.8.8.1.12
This parameter indicates if this interface is enabled to support VINES ARP.
Status: mandatory Access: read-write
OBJECT-TYPE    
  INTEGER enabled(1), disabled(2)  

wfVinesIfTrEndStation 1.3.6.1.4.1.18.3.5.8.8.1.13
This parameter indicates if this interface is enabled for source routing end station support.
Status: mandatory Access: read-write
OBJECT-TYPE    
  INTEGER enabled(1), disabled(2)  

wfVinesIfInPkts 1.3.6.1.4.1.18.3.5.8.8.1.14
The number of packets received on this interface.
Status: mandatory Access: read-only
OBJECT-TYPE    
  Counter  

wfVinesIfInErrs 1.3.6.1.4.1.18.3.5.8.8.1.15
The number of packets received with errors.
Status: mandatory Access: read-only
OBJECT-TYPE    
  Counter  

wfVinesIfOutPkts 1.3.6.1.4.1.18.3.5.8.8.1.16
The number of packets transmitted on this interface.
Status: mandatory Access: read-only
OBJECT-TYPE    
  Counter  

wfVinesIfOutErrs 1.3.6.1.4.1.18.3.5.8.8.1.17
The number of errors on packets transmitted.
Status: mandatory Access: read-only
OBJECT-TYPE    
  Counter  

wfVinesIfInMsgs 1.3.6.1.4.1.18.3.5.8.8.1.18
The number of messages received on this interface.
Status: mandatory Access: read-only
OBJECT-TYPE    
  Counter  

wfVinesIfMux 1.3.6.1.4.1.18.3.5.8.8.1.19
Muxing scheme for this interface. VINES currently only supports Ethernet encapsulation, but they plan to switch to SNAP.
Status: mandatory Access: read-write
OBJECT-TYPE    
  INTEGER enet(1), snap(2)  

wfVinesIfFwdDrops 1.3.6.1.4.1.18.3.5.8.8.1.20
The number of pakets that were dropped because of no forwarding information for the destination.
Status: mandatory Access: read-only
OBJECT-TYPE    
  Counter  

wfVinesIfZeroHopDrops 1.3.6.1.4.1.18.3.5.8.8.1.21
The number of pakets that were dropped because of a zero hop count.
Status: mandatory Access: read-only
OBJECT-TYPE    
  Counter  

wfVinesIfIcpInErrorNotifs 1.3.6.1.4.1.18.3.5.8.8.1.22
The number of ICP error notification packets received.
Status: mandatory Access: read-only
OBJECT-TYPE    
  Counter  

wfVinesIfIcpInMetricNotifs 1.3.6.1.4.1.18.3.5.8.8.1.23
The number of ICP metric notification packets received.
Status: mandatory Access: read-only
OBJECT-TYPE    
  Counter  

wfVinesIfIcpInErrors 1.3.6.1.4.1.18.3.5.8.8.1.24
The number of ICP packets received with errors.
Status: mandatory Access: read-only
OBJECT-TYPE    
  Counter  

wfVinesIfIcpOutErrorNotifs 1.3.6.1.4.1.18.3.5.8.8.1.25
The number of ICP error notification packets transmitted.
Status: mandatory Access: read-only
OBJECT-TYPE    
  Counter  

wfVinesIfIcpOutMetricNotifs 1.3.6.1.4.1.18.3.5.8.8.1.26
The number of ICP metric notification packets transmitted.
Status: mandatory Access: read-only
OBJECT-TYPE    
  Counter  

wfVinesIfArpInQueries 1.3.6.1.4.1.18.3.5.8.8.1.27
The number of ARP queries received.
Status: mandatory Access: read-only
OBJECT-TYPE    
  Counter  

wfVinesIfArpInAssgReqs 1.3.6.1.4.1.18.3.5.8.8.1.28
The number of ARP assignment requests received.
Status: mandatory Access: read-only
OBJECT-TYPE    
  Counter  

wfVinesIfArpInErrors 1.3.6.1.4.1.18.3.5.8.8.1.29
The number of ARP packets received with errors.
Status: mandatory Access: read-only
OBJECT-TYPE    
  Counter  

wfVinesIfArpOutServRsps 1.3.6.1.4.1.18.3.5.8.8.1.30
The number of ARP service responses sent.
Status: mandatory Access: read-only
OBJECT-TYPE    
  Counter  

wfVinesIfArpOutAssgRsps 1.3.6.1.4.1.18.3.5.8.8.1.31
The number of ARP assignment responses sent.
Status: mandatory Access: read-only
OBJECT-TYPE    
  Counter  

wfVinesIfInRedirects 1.3.6.1.4.1.18.3.5.8.8.1.32
The number of Redirect packets received.
Status: mandatory Access: read-only
OBJECT-TYPE    
  Counter  

wfVinesIfOutRedirects 1.3.6.1.4.1.18.3.5.8.8.1.33
The number of Redirect packets sent.
Status: mandatory Access: read-only
OBJECT-TYPE    
  Counter  

wfVinesIfEchoInPkts 1.3.6.1.4.1.18.3.5.8.8.1.34
The number of Echo packets received.
Status: mandatory Access: read-only
OBJECT-TYPE    
  Counter  

wfVinesIfEchoOutPkts 1.3.6.1.4.1.18.3.5.8.8.1.35
The number of Echo packets sent.
Status: mandatory Access: read-only
OBJECT-TYPE    
  Counter  

wfVinesIfReassFails 1.3.6.1.4.1.18.3.5.8.8.1.36
The number of packet reassemblies that failed.
Status: mandatory Access: read-only
OBJECT-TYPE    
  Counter  

wfVinesIfRemClientPrivDisable 1.3.6.1.4.1.18.3.5.8.8.1.37
This parameter indicates that this interface will allow remote clients privileges on this segment. This means that a client is not restricted to being within one hop of a VINES server.
Status: mandatory Access: read-write
OBJECT-TYPE    
  INTEGER enabled(1), disabled(2)  

wfVinesIfX25VC 1.3.6.1.4.1.18.3.5.8.9
OBJECT IDENTIFIER    

wfVinesIfX25VCNumber 1.3.6.1.4.1.18.3.5.8.9.1
This is the number of entries in the X.25 Virtual Circuit Table.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER  

wfVinesIfX25VCTable 1.3.6.1.4.1.18.3.5.8.10
This is the Table of X.25 Virtual Circuits.
Status: mandatory Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    WfVinesIfX25VCEntry

wfVinesIfX25VCEntry 1.3.6.1.4.1.18.3.5.8.10.1
An entry in the Table of X.25 Virtual Circuits.
Status: mandatory Access: not-accessible
OBJECT-TYPE    
  WfVinesIfX25VCEntry  

wfVinesIfX25VCSlot 1.3.6.1.4.1.18.3.5.8.10.1.1
The number of the slot in which the card is installed.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER  

wfVinesIfX25VCLine 1.3.6.1.4.1.18.3.5.8.10.1.2
For a serial line, this is the number of the line on the card.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER  

wfVinesIfX25VCCct 1.3.6.1.4.1.18.3.5.8.10.1.3
Local circuit number for this Virtual Circuit.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER  

wfVinesIfX25VCSession 1.3.6.1.4.1.18.3.5.8.10.1.4
Local session number for this Virtual Circuit.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER  

wfVinesIfX25VCTotIn 1.3.6.1.4.1.18.3.5.8.10.1.5
The total number of VINES IP packets received on this VC. Depending on the size of the X.25 packets received, more than one X.25 packet can make up a VINES IP packet.
Status: mandatory Access: read-only
OBJECT-TYPE    
  Counter  

wfVinesIfX25VCTotOut 1.3.6.1.4.1.18.3.5.8.10.1.6
The total number of VINES IP packets sent on this VC. Depending on the size of the X.25 packets sent, more than one X.25 packet can make up a VINES IP packet.
Status: mandatory Access: read-only
OBJECT-TYPE    
  Counter  

wfVinesIfX25VCInErrs 1.3.6.1.4.1.18.3.5.8.10.1.7
The total number of input errors.
Status: mandatory Access: read-only
OBJECT-TYPE    
  Counter  

wfVinesIfX25VCOutErrs 1.3.6.1.4.1.18.3.5.8.10.1.8
The total number of output errors.
Status: mandatory Access: read-only
OBJECT-TYPE    
  Counter  

wfVinesIfX25VCPktsOut 1.3.6.1.4.1.18.3.5.8.10.1.9
The total number of X.25 packets transmitted on this VC.
Status: mandatory Access: read-only
OBJECT-TYPE    
  Counter  

wfVinesIfX25VCPktsAwaitAck 1.3.6.1.4.1.18.3.5.8.10.1.10
Total number of X.25 packets transmitted on this VC waiting for ACK.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER  

wfVinesIfX25VCBytesOut 1.3.6.1.4.1.18.3.5.8.10.1.11
Total Bytes transmitted on this VC.
Status: mandatory Access: read-only
OBJECT-TYPE    
  Counter  

wfVinesIfX25VCBytesAwaitAck 1.3.6.1.4.1.18.3.5.8.10.1.12
Total bytes transmitted on this VC that are waiting for ACK.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER  

wfVinesIfX25VCPktsIn 1.3.6.1.4.1.18.3.5.8.10.1.13
Total X.25 packets received on this VC.
Status: mandatory Access: read-only
OBJECT-TYPE    
  Counter  

wfVinesIfX25VCBytesIn 1.3.6.1.4.1.18.3.5.8.10.1.14
Total Bytes received on this VC.
Status: mandatory Access: read-only
OBJECT-TYPE    
  Counter  

wfVinesIfX25VCResetsIn 1.3.6.1.4.1.18.3.5.8.10.1.15
Number of X.25 reset packets received on this VC.
Status: mandatory Access: read-only
OBJECT-TYPE    
  Counter  

wfVinesIfX25VCResetsOut 1.3.6.1.4.1.18.3.5.8.10.1.16
Number of X.25 reset packets transmitted on this VC.
Status: mandatory Access: read-only
OBJECT-TYPE    
  Counter  

wfVinesTrafficFilterTable 1.3.6.1.4.1.18.3.5.8.11
VINES Traffic Filters
Status: mandatory Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    WfVinesTrafficFilterEntry

wfVinesTrafficFilterEntry 1.3.6.1.4.1.18.3.5.8.11.1
An entry in WfVinesTrafficFilterTable.
Status: mandatory Access: not-accessible
OBJECT-TYPE    
  WfVinesTrafficFilterEntry  

wfVinesTrafficFilterCreate 1.3.6.1.4.1.18.3.5.8.11.1.1
Defines the existence of the traffic filter rule: created - traffic filter exists delete - traffic filter does not exist and can be deleted.
Status: mandatory Access: read-write
OBJECT-TYPE    
  INTEGER created(1), deleted(2)  

wfVinesTrafficFilterEnable 1.3.6.1.4.1.18.3.5.8.11.1.2
Defines whether or not the traffic filter rule should be used: enabled - activate the rule. disabled - inactivate the rule.
Status: mandatory Access: read-write
OBJECT-TYPE    
  INTEGER enabled(1), disabled(2)  

wfVinesTrafficFilterStatus 1.3.6.1.4.1.18.3.5.8.11.1.3
Defines the current status of the traffic filter: inactive - the rule is not in use. active - the rule is being used. error - the application detected an error in the rule.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER active(1), error(2), inactive(3)  

wfVinesTrafficFilterCounter 1.3.6.1.4.1.18.3.5.8.11.1.4
The number of received packets that have matched this rule.
Status: mandatory Access: read-only
OBJECT-TYPE    
  Counter  

wfVinesTrafficFilterDefinition 1.3.6.1.4.1.18.3.5.8.11.1.5
The filter rule definition.
Status: mandatory Access: read-write
OBJECT-TYPE    
  OCTET STRING  

wfVinesTrafficFilterReserved 1.3.6.1.4.1.18.3.5.8.11.1.6
Reserved field.
Status: mandatory Access: not-accessible
OBJECT-TYPE    
  INTEGER  

wfVinesTrafficFilterCircuit 1.3.6.1.4.1.18.3.5.8.11.1.7
The ID of the Circuit to which the filter is applied.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER  

wfVinesTrafficFilterRuleNumber 1.3.6.1.4.1.18.3.5.8.11.1.8
ID for the rule.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER  

wfVinesTrafficFilterFragment 1.3.6.1.4.1.18.3.5.8.11.1.9
Fragment number - for large rules.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER  

wfVinesNameTable 1.3.6.1.4.1.18.3.5.8.12
This is the Name-to-Address Binding Table.
Status: mandatory Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    WfVinesNameEntry

wfVinesNameEntry 1.3.6.1.4.1.18.3.5.8.12.1
An entry in the Table of Names.
Status: mandatory Access: not-accessible
OBJECT-TYPE    
  WfVinesNameEntry  

wfVinesNameDelete 1.3.6.1.4.1.18.3.5.8.12.1.1
Create/Delete parameter. Users perform an SNMP set command to create/delete this name.
Status: mandatory Access: read-write
OBJECT-TYPE    
  INTEGER created(1), deleted(2)  

wfVinesNameDisable 1.3.6.1.4.1.18.3.5.8.12.1.2
Enable/Disable parameter. Users perform an SNMP set command to enable/disable a name.
Status: mandatory Access: read-write
OBJECT-TYPE    
  INTEGER enabled(1), disabled(2)  

wfVinesNameNetid 1.3.6.1.4.1.18.3.5.8.12.1.3
This is the network number for the host.
Status: mandatory Access: read-write
OBJECT-TYPE    
  Counter  

wfVinesNameHost 1.3.6.1.4.1.18.3.5.8.12.1.4
This is the name of the host.
Status: mandatory Access: read-write
OBJECT-TYPE    
  DisplayString  

wfVinesNameSubNetid 1.3.6.1.4.1.18.3.5.8.12.1.5
This is the subnetwork number for the host.
Status: mandatory Access: read-write
OBJECT-TYPE    
  INTEGER  

wfVinesArp 1.3.6.1.4.1.18.3.5.8.13
OBJECT IDENTIFIER    

wfVinesArpDelete 1.3.6.1.4.1.18.3.5.8.13.1
Create/Delete parameter. Default is created. Users perform an SNMP SET operation on this object in order to create/delete ARP.
Status: mandatory Access: read-write
OBJECT-TYPE    
  INTEGER created(1), deleted(2)  

wfVinesArpDisable 1.3.6.1.4.1.18.3.5.8.13.2
Enable/Disable Parameter indicates whether this ARP record is enabled or disabled.
Status: mandatory Access: read-write
OBJECT-TYPE    
  INTEGER enabled(1), disabled(2)  

wfVinesArpState 1.3.6.1.4.1.18.3.5.8.13.3
State of ARP.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER up(1), down(2)  

wfVinesArpSubnetid 1.3.6.1.4.1.18.3.5.8.13.4
The next subnetwork ID to be assigned.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER  

wfVinesArpSubnetBlock 1.3.6.1.4.1.18.3.5.8.13.5
The size of the block of subnet ids a slot can grab.
Status: mandatory Access: read-write
OBJECT-TYPE    
  INTEGER minimum(1), default(2), maximum(32)  

wfVinesArpAssignDeniedPkts 1.3.6.1.4.1.18.3.5.8.13.6
Number of ARP Assignment packets received for which we didn't have a free subnet number.
Status: mandatory Access: read-only
OBJECT-TYPE    
  Counter  

wfXnsBase 1.3.6.1.4.1.18.3.5.10.1
OBJECT IDENTIFIER    

wfXnsBaseDelete 1.3.6.1.4.1.18.3.5.10.1.1
Create/Delete parameter. Default is created. Users perform an SNMP SET operation on this object in order to create/delete XNS.
Status: mandatory Access: read-write
OBJECT-TYPE    
  INTEGER created(1), deleted(2)  

wfXnsBaseDisable 1.3.6.1.4.1.18.3.5.10.1.2
Enable/Disable parameter. Default is enabled. Users perform an SNMP SET operation on this object in order to enable/disable XNS.
Status: mandatory Access: read-write
OBJECT-TYPE    
  INTEGER enabled(1), disabled(2)  

wfXnsBaseState 1.3.6.1.4.1.18.3.5.10.1.3
The current state of the entire XNS.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER up(1), down(2), init(3), notpresent(4)  

wfXnsBaseHostNumber 1.3.6.1.4.1.18.3.5.10.1.4
Host Number of Router and potential MAC address of box.
Status: mandatory Access: read-write
OBJECT-TYPE    
  OCTET STRING  

wfXnsBaseRtEntryTable 1.3.6.1.4.1.18.3.5.10.2
The table of Elements in XNS's routing table
Status: mandatory Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    WfXnsBaseRtEntry

wfXnsBaseRtEntry 1.3.6.1.4.1.18.3.5.10.2.1
An entry in the Routing Table
Status: mandatory Access: not-accessible
OBJECT-TYPE    
  WfXnsBaseRtEntry  

wfXnsBaseRouteDest 1.3.6.1.4.1.18.3.5.10.2.1.1
The destination XNS address of this route. An entry with a value of 0.0.0.0 is considered a default route. Multiple routes to a single destination can appear in the table, but access to such multiple entries is dependent on the table- access mechanisms defined by the network management protocol in use.
Status: mandatory Access: read-only
OBJECT-TYPE    
  OCTET STRING  

wfXnsBaseRouteIfIndex 1.3.6.1.4.1.18.3.5.10.2.1.2
The index value which uniquely identifies the local interface through which the next hop of this route should be reached. The interface identified by a particular value of this index is the same interface as identified by the same value of ifIndex.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER  

wfXnsBaseRouteMetric 1.3.6.1.4.1.18.3.5.10.2.1.3
The primary routing metric for this route. The semantics of this metric are determined by the routing-protocol specified in the route's ipRouteProto value. If this metric is not used, its value should be set to -1.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER  

wfXnsBaseRouteNextHopNetwork 1.3.6.1.4.1.18.3.5.10.2.1.4
(In the case of a route bound to an interface which is realized via a broadcast media, the value of this field is the agent's XNS address on that interface.)
Status: mandatory Access: read-only
OBJECT-TYPE    
  OCTET STRING  

wfXnsBaseRouteNextHopHost 1.3.6.1.4.1.18.3.5.10.2.1.5
Full network.host_id address of nexthop host for this network.
Status: mandatory Access: read-only
OBJECT-TYPE    
  OCTET STRING  

wfXnsBaseRouteType 1.3.6.1.4.1.18.3.5.10.2.1.6
The type of route. Note that the values direct(3) and indirect(4) refer to the notion of direct and indirect routing in the XNS architecture. Setting this object to the value invalid(2) has the effect of invalidating the corresponding entry in the ipRouteTable object. That is, it effectively dissasociates the destination identified with said entry from the route identified with said entry. It is an implementation-specific matter as to whether the agent removes an invalidated entry from the table. nagement stations must be prepared to receive tabular information from agents that corresponds to entries not currently in use. Proper interpretation of such entries requires examination of the relevant ipRouteType object.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER other(1), invalid(2), direct(3), indirect(4), static(5)  

wfXnsBaseRouteProto 1.3.6.1.4.1.18.3.5.10.2.1.7
The routing mechanism via which this route was learned. Inclusion of values for gateway routing protocols is not intended to imply that hosts should support those protocols.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER other(1), local(2), netmgmt(3), rip(4)  

wfXnsBaseRouteAge 1.3.6.1.4.1.18.3.5.10.2.1.8
The number of seconds since this route was last updated or otherwise determined to be correct. Note that no semantics of `too old' can be implied except through knowledge of the routing protocol by which the route was learned.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER  

wfXnsBaseRouteInfo 1.3.6.1.4.1.18.3.5.10.2.1.9
A user-defined string which describes this Route entry
Status: mandatory Access: read-only
OBJECT-TYPE    
  OCTET STRING  

wfXnsInterfaceTable 1.3.6.1.4.1.18.3.5.10.3
The network interface record
Status: mandatory Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    WfXnsInterfaceEntry

wfXnsInterfaceEntry 1.3.6.1.4.1.18.3.5.10.3.1
An entry in the Routing Table
Status: mandatory Access: not-accessible
OBJECT-TYPE    
  WfXnsInterfaceEntry  

wfXnsInterfaceIndex 1.3.6.1.4.1.18.3.5.10.3.1.1
A unique value for each XNS interface. Its value ranges between 1 and the value of MAXCIRCUITS.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER  

wfXnsInterfaceDelete 1.3.6.1.4.1.18.3.5.10.3.1.2
Create/Delete parameter. Default is created. Users perform an SNMP SET operation on this object in order to create/delete an XNS interface.
Status: mandatory Access: read-write
OBJECT-TYPE    
  INTEGER created(1), deleted(2)  

wfXnsInterfaceDisable 1.3.6.1.4.1.18.3.5.10.3.1.3
Enable/Disable parameter. Default is enabled. Users perform an SNMP SET operation on this object in order to enable/disable an XNS interface.
Status: mandatory Access: read-write
OBJECT-TYPE    
  INTEGER enabled(1), disabled(2)  

wfXnsInterfaceState 1.3.6.1.4.1.18.3.5.10.3.1.4
The current state of the XNS interface
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER up(1), down(2), init(3), notpresent(4)  

wfXnsInterfaceCircuit 1.3.6.1.4.1.18.3.5.10.3.1.5
The Circuit Number that this interface runs over
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER  

wfXnsInterfaceNetworkNumber 1.3.6.1.4.1.18.3.5.10.3.1.6
The XNS Address to which this entry's addressing information pertains
Status: mandatory Access: read-only
OBJECT-TYPE    
  OCTET STRING  

wfXnsInterfaceCost 1.3.6.1.4.1.18.3.5.10.3.1.7
The Cost associated with the XNS Address of this entry
Status: mandatory Access: read-write
OBJECT-TYPE    
  INTEGER  

wfXnsInterfaceXsumOn 1.3.6.1.4.1.18.3.5.10.3.1.8
Flag for checksums
Status: mandatory Access: read-write
OBJECT-TYPE    
  INTEGER enabled(1), disabled(2)  

wfXnsInterfaceEncaps 1.3.6.1.4.1.18.3.5.10.3.1.9
If changed while router is running yowsa !!!!
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER ethernet(1), snap(2)  

wfXnsInterfaceMacAddress 1.3.6.1.4.1.18.3.5.10.3.1.10
The MacAddress of this interface this port will receive or transmit.
Status: mandatory Access: read-write
OBJECT-TYPE    
  OCTET STRING  

wfXnsInterfaceSMDSGroupAddress 1.3.6.1.4.1.18.3.5.10.3.1.11
The SMDS Group Address of this interface this port will receive or transmit.
Status: mandatory Access: read-write
OBJECT-TYPE    
  OCTET STRING  

wfXnsInterfaceMaxInfo 1.3.6.1.4.1.18.3.5.10.3.1.12
The maximum size of the INFO (non-MAC) field that this port will receive or transmit.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER  

wfXnsInterfaceExtServer 1.3.6.1.4.1.18.3.5.10.3.1.13
Flag indicating if this interface has External server capabilities turned on. Allows interface to pass on defined packets, such as PEP/TP requests, to a remote server not located on local network.
Status: mandatory Access: read-write
OBJECT-TYPE    
  INTEGER enabled(1), disabled(2)  

wfXnsInterfaceExServNetwork 1.3.6.1.4.1.18.3.5.10.3.1.14
The Network address of the remote server.
Status: mandatory Access: read-write
OBJECT-TYPE    
  OCTET STRING  

wfXnsInterfaceExServHostId 1.3.6.1.4.1.18.3.5.10.3.1.15
The Host ID of the remote server.
Status: mandatory Access: read-write
OBJECT-TYPE    
  OCTET STRING  

wfXnsInterfaceExServPktType 1.3.6.1.4.1.18.3.5.10.3.1.16
The packet type of the requests which are to be passed on to the specified remote server.
Status: mandatory Access: read-write
OBJECT-TYPE    
  OCTET STRING  

wfXnsInterfaceExServSockNm 1.3.6.1.4.1.18.3.5.10.3.1.17
The destination socket number of the requests which are to be passed on to the specified remote server. If no socket number is specified then all packets of the specified type that this interface receives will be forwarded to specified remote server.
Status: mandatory Access: read-write
OBJECT-TYPE    
  OCTET STRING  

wfXnsInterfaceInReceives 1.3.6.1.4.1.18.3.5.10.3.1.18
The total number of input datagrams received from interfaces, including those received in error.
Status: mandatory Access: read-only
OBJECT-TYPE    
  Counter  

wfXnsInterfaceInHdrErrors 1.3.6.1.4.1.18.3.5.10.3.1.19
The number of input datagrams discarded due to errors in their XNS headers, including bad checksums, version number mismatch, other format errors, time-to-live exceeded, errors discovered in processing their XNS options, etc.
Status: mandatory Access: read-only
OBJECT-TYPE    
  Counter  

wfXnsInterfaceInAddrErrors 1.3.6.1.4.1.18.3.5.10.3.1.20
The number of input datagrams discarded because the XNS address in their XNS header's destination field was not a valid address to be received at this entity. This count includes invalid addresses (e.g., 0.0.0.0) and addresses of unsupported Classes (e.g., Class E). For entities which are not XNS Gateways and therefore do not forward datagrams, this counter includes datagrams discarded because the destination address was not a local address.
Status: mandatory Access: read-only
OBJECT-TYPE    
  Counter  

wfXnsInterfaceForwDatagrams 1.3.6.1.4.1.18.3.5.10.3.1.21
The number of input datagrams for which this entity was not their final XNS destination, as a result of which an attempt was made to find a route to forward them to that final destination. In entities which do not act as XNS Gateways, this counter will include only those packets which were Source-Routed via this entity, and the Source- Route option processing was successful.
Status: mandatory Access: read-only
OBJECT-TYPE    
  Counter  

wfXnsInterfaceInUnknownProtos 1.3.6.1.4.1.18.3.5.10.3.1.22
The number of locally-addressed datagrams received successfully but discarded because of an unknown or unsupported protocol.
Status: mandatory Access: read-only
OBJECT-TYPE    
  Counter  

wfXnsInterfaceInDiscards 1.3.6.1.4.1.18.3.5.10.3.1.23
The number of input XNS datagrams for which no problems were encountered to prevent their continued processing, but which were discarded (e.g., for lack of buffer space). Note that this counter does not include any datagrams discarded while awaiting re-assembly.
Status: mandatory Access: read-only
OBJECT-TYPE    
  Counter  

wfXnsInterfaceInDelivers 1.3.6.1.4.1.18.3.5.10.3.1.24
The total number of input datagrams successfully delivered to XNS user-protocols (including ICMP).
Status: mandatory Access: read-only
OBJECT-TYPE    
  Counter  

wfXnsInterfaceOutRequests 1.3.6.1.4.1.18.3.5.10.3.1.25
The total number of XNS datagrams which local XNS user-protocols supplied to XNS in requests for transmission. Note that this counter does not include any datagrams counted in XnsInteraceFwdDatagrams.
Status: mandatory Access: read-only
OBJECT-TYPE    
  Counter  

wfXnsInterfaceOutDiscards 1.3.6.1.4.1.18.3.5.10.3.1.26
The number of output XNS datagrams for which no problem was encountered to prevent their transmission to their destination, but which were discarded (e.g., for lack of buffer space). Note that this counter would include datagrams counted in XnsForwDatagrams if any such packets met this (discretionary) discard criterion.
Status: mandatory Access: read-only
OBJECT-TYPE    
  Counter  

wfXnsInterfaceOutNoRoutes 1.3.6.1.4.1.18.3.5.10.3.1.27
The number of XNS datagrams discarded because no route could be found to transmit them to their destination. Note that this counter includes any packets counted in ipForwDatagrams which meet this `no-route' criterion. Note that this includes any datagarms which a host cannot route because all of its default gateways are down.
Status: mandatory Access: read-only
OBJECT-TYPE    
  Counter  

wfXnsInterfaceFRBcast 1.3.6.1.4.1.18.3.5.10.3.1.28
Configurable Frame Relay broadcast address
Status: mandatory Access: read-write
OBJECT-TYPE    
  OCTET STRING  

wfXnsInterfaceFRMcast 1.3.6.1.4.1.18.3.5.10.3.1.29
Configurable Frame Relay multicast address
Status: mandatory Access: read-write
OBJECT-TYPE    
  OCTET STRING  

wfXnsRipIntfTable 1.3.6.1.4.1.18.3.5.10.4
The list of RIP interfaces
Status: mandatory Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    WfXnsRipIntfEntry

wfXnsRipIntfEntry 1.3.6.1.4.1.18.3.5.10.4.1
An entry in the Routing Table
Status: mandatory Access: not-accessible
OBJECT-TYPE    
  WfXnsRipIntfEntry  

wfXnsRipInterfaceDelete 1.3.6.1.4.1.18.3.5.10.4.1.1
Create/Delete parameter. Default is created. Users perform an SNMP SET operation on this object in order to create/delete an RIP Interface instance.
Status: mandatory Access: read-write
OBJECT-TYPE    
  INTEGER created(1), deleted(2)  

wfXnsRipInterfaceDisable 1.3.6.1.4.1.18.3.5.10.4.1.2
Enable/Disable parameter. Default is enabled. Users perform an SNMP SET operation on this object in order to enable/disable a RIP instance.
Status: mandatory Access: read-write
OBJECT-TYPE    
  INTEGER enabled(1), disabled(2)  

wfXnsRipInterfaceState 1.3.6.1.4.1.18.3.5.10.4.1.3
The current state of RIP on this interface.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER up(1), down(2), init(3), notpresent(4)  

wfXnsRipInterfaceIndex 1.3.6.1.4.1.18.3.5.10.4.1.4
The XNS interface to run RIP on.
Status: mandatory Access: read-only
OBJECT-TYPE    
  OCTET STRING  

wfXnsRipInterfaceSupply 1.3.6.1.4.1.18.3.5.10.4.1.5
Transmit RIP packets.
Status: mandatory Access: read-write
OBJECT-TYPE    
  INTEGER enabled(1), disabled(2)  

wfXnsRipInterfaceListen 1.3.6.1.4.1.18.3.5.10.4.1.6
Receive RIP packets.
Status: mandatory Access: read-write
OBJECT-TYPE    
  INTEGER enabled(1), disabled(2)  

wfXnsAdjacentHostTable 1.3.6.1.4.1.18.3.5.10.5
must be configured for a nexthop host.
Status: mandatory Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    WfXnsAdjacentHostEntry

wfXnsAdjacentHostEntry 1.3.6.1.4.1.18.3.5.10.5.1
An entry in the Adjacent Host Table
Status: mandatory Access: not-accessible
OBJECT-TYPE    
  WfXnsAdjacentHostEntry  

wfXnsAhDelete 1.3.6.1.4.1.18.3.5.10.5.1.1
Create/Delete parameter. Default is created. Users perform an SNMP SET operation on this object in order to create/delete the IPX Static Host.
Status: mandatory Access: read-write
OBJECT-TYPE    
  INTEGER created(1), deleted(2)  

wfXnsAhDisable 1.3.6.1.4.1.18.3.5.10.5.1.2
Enable/Disable parameter. Default is enabled. Users perform an SNMP SET operation on this object in order to enable/disable this IPX Static Route.
Status: mandatory Access: read-write
OBJECT-TYPE    
  INTEGER enabled(1), disabled(2)  

wfXnsAhTargHostNetwork 1.3.6.1.4.1.18.3.5.10.5.1.3
The network address of the static host.
Status: mandatory Access: read-only
OBJECT-TYPE    
  OCTET STRING  

wfXnsAhTargHostId 1.3.6.1.4.1.18.3.5.10.5.1.4
The Address of this static host.
Status: mandatory Access: read-only
OBJECT-TYPE    
  OCTET STRING  

wfXnsAhNextHopIntf 1.3.6.1.4.1.18.3.5.10.5.1.5
The Next Hop Interface Network Address
Status: mandatory Access: read-write
OBJECT-TYPE    
  OCTET STRING  

wfXnsAhDlci 1.3.6.1.4.1.18.3.5.10.5.1.6
The next Hop Host address
Status: mandatory Access: read-write
OBJECT-TYPE    
  OCTET STRING  

wfXnsStaticRouteTable 1.3.6.1.4.1.18.3.5.10.6
The list of Adjacent Hosts used for Configuring XNS
Status: mandatory Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    WfXnsStaticRouteEntry

wfXnsStaticRouteEntry 1.3.6.1.4.1.18.3.5.10.6.1
An entry in the Host Table
Status: mandatory Access: not-accessible
OBJECT-TYPE    
  WfXnsStaticRouteEntry  

wfXnsSrDelete 1.3.6.1.4.1.18.3.5.10.6.1.1
Create/Delete parameter. Default is created. Users perform an SNMP SET operation on this object in order to create/delete the XNS Static Route.
Status: mandatory Access: read-write
OBJECT-TYPE    
  INTEGER created(1), deleted(2)  

wfXnsSrDisable 1.3.6.1.4.1.18.3.5.10.6.1.2
Enable/Disable parameter. Default is enabled. Users perform an SNMP SET operation on this object in order to enable/disable this XNS Static Route.
Status: mandatory Access: read-write
OBJECT-TYPE    
  INTEGER enabled(1), disabled(2)  

wfXnsSrTargNetwork 1.3.6.1.4.1.18.3.5.10.6.1.3
The Address of this static route
Status: mandatory Access: read-only
OBJECT-TYPE    
  OCTET STRING  

wfXnsSrCost 1.3.6.1.4.1.18.3.5.10.6.1.4
The Cost of this Static Route
Status: mandatory Access: read-write
OBJECT-TYPE    
  INTEGER  

wfXnsSrNextHopNetwork 1.3.6.1.4.1.18.3.5.10.6.1.5
The Next Hop XNS Address
Status: mandatory Access: read-only
OBJECT-TYPE    
  OCTET STRING  

wfXnsSrNextHopHost 1.3.6.1.4.1.18.3.5.10.6.1.6
The next Hop Host address
Status: mandatory Access: read-write
OBJECT-TYPE    
  OCTET STRING  

wfXnsSrTargNetworkRt 1.3.6.1.4.1.18.3.5.10.6.1.7
The Route Identifier Which numbered route this is to be
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER  

wfXnsTrafficFilterTable 1.3.6.1.4.1.18.3.5.10.7
XNS Traffic Filters
Status: mandatory Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    WfXnsTrafficFilterEntry

wfXnsTrafficFilterEntry 1.3.6.1.4.1.18.3.5.10.7.1
A traffic filter definition
Status: mandatory Access: not-accessible
OBJECT-TYPE    
  WfXnsTrafficFilterEntry  

wfXnsTrafficFilterCreate 1.3.6.1.4.1.18.3.5.10.7.1.1
Defines the existence of the traffic filter rule: created - traffic filter exists delete - traffic filter does not exist and can be deleted.
Status: mandatory Access: read-write
OBJECT-TYPE    
  INTEGER created(1), deleted(2)  

wfXnsTrafficFilterEnable 1.3.6.1.4.1.18.3.5.10.7.1.2
Defines whether or not the traffic filter rule should be used: enabled - activate the rule. disabled - inactivate the rule.
Status: mandatory Access: read-write
OBJECT-TYPE    
  INTEGER enabled(1), disabled(2)  

wfXnsTrafficFilterStatus 1.3.6.1.4.1.18.3.5.10.7.1.3
Defines the current status of the traffic filter: inactive - the rule is not in use. active - the rule is being used. error - the application detected an error in the rule.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER active(1), error(2), inactive(3)  

wfXnsTrafficFilterCounter 1.3.6.1.4.1.18.3.5.10.7.1.4
The number of received packets that have matched this rule.
Status: mandatory Access: read-only
OBJECT-TYPE    
  Counter  

wfXnsTrafficFilterDefinition 1.3.6.1.4.1.18.3.5.10.7.1.5
The filter rule definition.
Status: mandatory Access: read-write
OBJECT-TYPE    
  Opaque  

wfXnsTrafficFilterReserved 1.3.6.1.4.1.18.3.5.10.7.1.6
Reserved field.
Status: mandatory Access: not-accessible
OBJECT-TYPE    
  INTEGER  

wfXnsTrafficFilterInterface 1.3.6.1.4.1.18.3.5.10.7.1.7
The network address of the XNS interface to which this filter is applied.
Status: mandatory Access: read-only
OBJECT-TYPE    
  OCTET STRING  

wfXnsTrafficFilterCircuit 1.3.6.1.4.1.18.3.5.10.7.1.8
The ID of the Circuit to which the filter is applied.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER  

wfXnsTrafficFilterRuleNumber 1.3.6.1.4.1.18.3.5.10.7.1.9
ID for the rule.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER  

wfXnsTrafficFilterFragment 1.3.6.1.4.1.18.3.5.10.7.1.10
Fragment number - for large rules.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER  

Generation date: July 28, 2023, 16:18:13, Copyright © 2007 - 2022 - Circitor