WINDOWS-NT-PERFORMANCE

File: WINDOWS-NT-PERFORMANCE.mib (346273 bytes)

Imported modules

RFC1155-SMI RFC-1212 RFC1213-MIB

Imported symbols

Counter TimeTicks enterprises
OBJECT-TYPE DisplayString

Defined Types

CpuprocessorEntry  
SEQUENCE    
  cpuprocessorIndex INTEGER
  cpuprocessorInstance DisplayString
  cpuPercentProcessorTime INTEGER
  cpuPercentUserTime INTEGER
  cpuPercentPrivilegedTime INTEGER
  cpuInterruptsPerSec Counter
  cpuPercentDPCTime INTEGER
  cpuPercentInterruptTime INTEGER
  cpuDPCsQueuedPerSec Counter
  cpuDPCRate INTEGER
  cpuDPCBypassesPerSec Counter
  cpuAPCBypassesPerSec Counter

Netnetwork-InterfaceEntry  
SEQUENCE    
  netnetwork-InterfaceIndex INTEGER
  netnetwork-InterfaceInstance DisplayString
  netBytesTotalPerSec Counter
  netPacketsPerSec Counter
  netPacketsReceivedPerSec Counter
  netPacketsSentPerSec Counter
  netCurrentBandwidth INTEGER
  netBytesReceivedPerSec Counter
  netPacketsReceivedUnicastPerSec Counter
  netPacketsReceivedNon-UnicastPerSec Counter
  netPacketsReceivedDiscarded INTEGER
  netPacketsReceivedErrors INTEGER
  netPacketsReceivedUnknown INTEGER
  netBytesSentPerSec Counter
  netPacketsSentUnicastPerSec Counter
  netPacketsSentNon-UnicastPerSec Counter
  netPacketsOutboundDiscarded INTEGER
  netPacketsOutboundErrors INTEGER
  netOutputQueueLength INTEGER

PdiskphysicalDiskEntry  
SEQUENCE    
  pdiskphysicalDiskIndex INTEGER
  pdiskphysicalDiskInstance DisplayString
  pdiskCurrentDiskQueueLength INTEGER
  pdiskPercentDiskTime TimeTicks
  pdiskAvgDiskQueueLength INTEGER
  pdiskPercentDiskReadTime TimeTicks
  pdiskAvgDiskReadQueueLength INTEGER
  pdiskPercentDiskWriteTime TimeTicks
  pdiskAvgDiskWriteQueueLength INTEGER
  pdiskAvgDiskSecPerTransfer TimeTicks
  pdiskAvgDiskSecPerRead TimeTicks
  pdiskAvgDiskSecPerWrite TimeTicks
  pdiskDiskTransfersPerSec Counter
  pdiskDiskReadsPerSec Counter
  pdiskDiskWritesPerSec Counter
  pdiskDiskBytesPerSec INTEGER
  pdiskDiskReadBytesPerSec INTEGER
  pdiskDiskWriteBytesPerSec INTEGER

LdisklogicalDiskEntry  
SEQUENCE    
  ldisklogicalDiskIndex INTEGER
  ldisklogicalDiskInstance DisplayString
  ldiskPercentFreeSpace INTEGER
  ldiskFreeMegabytes INTEGER
  ldiskCurrentDiskQueueLength INTEGER
  ldiskPercentDiskTime TimeTicks
  ldiskAvgDiskQueueLength INTEGER
  ldiskPercentDiskReadTime TimeTicks
  ldiskAvgDiskReadQueueLength INTEGER
  ldiskPercentDiskWriteTime TimeTicks
  ldiskAvgDiskWriteQueueLength INTEGER
  ldiskAvgDiskSecPerTransfer TimeTicks
  ldiskAvgDiskSecPerRead TimeTicks
  ldiskAvgDiskSecPerWrite TimeTicks
  ldiskDiskTransfersPerSec Counter
  ldiskDiskReadsPerSec Counter
  ldiskDiskWritesPerSec Counter
  ldiskDiskBytesPerSec INTEGER
  ldiskDiskReadBytesPerSec INTEGER
  ldiskDiskWriteBytesPerSec INTEGER

Pagefilepaging-FileEntry  
SEQUENCE    
  pagefilepaging-FileIndex INTEGER
  pagefilepaging-FileInstance DisplayString
  pagefilePercentUsage INTEGER
  pagefilePercentUsagePeak INTEGER

ProcessprocessEntry  
SEQUENCE    
  processprocessIndex INTEGER
  processprocessInstance DisplayString
  processPercentProcessorTime INTEGER
  processPercentUserTime INTEGER
  processPercentPrivilegedTime INTEGER
  processVirtualBytesPeak INTEGER
  processVirtualBytes INTEGER
  processPageFaultsPerSec Counter
  processWorkingSetPeak INTEGER
  processWorkingSet INTEGER
  processPageFileBytesPeak INTEGER
  processPageFileBytes INTEGER
  processPrivateBytes INTEGER
  processThreadCount INTEGER
  processPriorityBase INTEGER
  processElapsedTime TimeTicks
  processIDProcess INTEGER
  processPoolPagedBytes INTEGER
  processPoolNonpagedBytes INTEGER
  processHandleCount INTEGER

NetbeuinetBEUIEntry  
SEQUENCE    
  netbeuinetBEUIIndex INTEGER
  netbeuinetBEUIInstance DisplayString
  netbeuiDatagramsPerSec Counter
  netbeuiDatagramBytesPerSec INTEGER
  netbeuiPacketsPerSec Counter
  netbeuiFramesPerSec Counter
  netbeuiFrameBytesPerSec INTEGER
  netbeuiBytesTotalPerSec INTEGER
  netbeuiConnectionsOpen INTEGER
  netbeuiConnectionsNoRetries INTEGER
  netbeuiConnectionsWithRetries INTEGER
  netbeuiDisconnectsLocal INTEGER
  netbeuiDisconnectsRemote INTEGER
  netbeuiFailuresLink INTEGER
  netbeuiFailuresAdapter INTEGER
  netbeuiConnectionSessionTimeouts INTEGER
  netbeuiConnectionsCanceled INTEGER
  netbeuiFailuresResourceRemote INTEGER
  netbeuiFailuresResourceLocal INTEGER
  netbeuiFailuresNotFound INTEGER
  netbeuiFailuresNoListen INTEGER
  netbeuiDatagramsSentPerSec Counter
  netbeuiDatagramBytesSentPerSec INTEGER
  netbeuiDatagramsReceivedPerSec Counter
  netbeuiDatagramBytesReceivedPerSec INTEGER
  netbeuiPacketsSentPerSec Counter
  netbeuiPacketsReceivedPerSec Counter
  netbeuiFramesSentPerSec Counter
  netbeuiFrameBytesSentPerSec INTEGER
  netbeuiFramesReceivedPerSec Counter
  netbeuiFrameBytesReceivedPerSec INTEGER
  netbeuiFramesRe-SentPerSec Counter
  netbeuiFrameBytesRe-SentPerSec INTEGER
  netbeuiFramesRejectedPerSec Counter
  netbeuiFrameBytesRejectedPerSec INTEGER
  netbeuiExpirationsResponse INTEGER
  netbeuiExpirationsAck INTEGER
  netbeuiWindowSendMaximum INTEGER
  netbeuiWindowSendAverage INTEGER
  netbeuiPiggybackAckQueuedPerSec Counter
  netbeuiPiggybackAckTimeouts INTEGER

NbtconnnBT-ConnectionEntry  
SEQUENCE    
  nbtconnnBT-ConnectionIndex INTEGER
  nbtconnnBT-ConnectionInstance DisplayString
  nbtconnBytesReceivedPerSec INTEGER
  nbtconnBytesSentPerSec INTEGER
  nbtconnBytesTotalPerSec INTEGER



Srvrqueuesserver-Work-QueuesEntry  
SEQUENCE    
  srvrqueuesserver-Work-QueuesIndex INTEGER
  srvrqueuesserver-Work-QueuesInstance DisplayString
  srvrqueuesQueueLength INTEGER
  srvrqueuesActiveThreads INTEGER
  srvrqueuesAvailableThreads INTEGER
  srvrqueuesAvailableWorkItems INTEGER
  srvrqueuesBorrowedWorkItems INTEGER
  srvrqueuesWorkItemShortages INTEGER
  srvrqueuesCurrentClients INTEGER
  srvrqueuesBytesReceivedPerSec INTEGER
  srvrqueuesBytesSentPerSec INTEGER
  srvrqueuesBytesTransferredPerSec INTEGER
  srvrqueuesReadOperationsPerSec INTEGER
  srvrqueuesReadBytesPerSec INTEGER
  srvrqueuesWriteOperationsPerSec INTEGER
  srvrqueuesWriteBytesPerSec INTEGER
  srvrqueuesTotalBytesPerSec INTEGER
  srvrqueuesTotalOperationsPerSec INTEGER
  srvrqueuesContextBlocksQueuedPerSec Counter

ExchmtaconnmSExchangeMTA-ConnectionsEntry  
SEQUENCE    
  exchmtaconnmSExchangeMTA-ConnectionsIndex INTEGER
  exchmtaconnmSExchangeMTA-ConnectionsInstance DisplayString
  exchmtaconnAssociations INTEGER
  exchmtaconnReceiveBytesPerSec Counter
  exchmtaconnSendBytesPerSec Counter
  exchmtaconnReceiveMessagesPerSec Counter
  exchmtaconnSendMessagesPerSec Counter
  exchmtaconnQueueLength INTEGER
  exchmtaconnConnectorIndex INTEGER
  exchmtaconnInboundRejectedTotal INTEGER
  exchmtaconnTotalRecipientsQueued INTEGER
  exchmtaconnOldestMessageQueued TimeTicks
  exchmtaconnCurrentInboundAssociations INTEGER
  exchmtaconnCurrentOutboundAssociations INTEGER
  exchmtaconnCumulativeInboundAssociations INTEGER
  exchmtaconnCumulativeOutboundAssociations INTEGER
  exchmtaconnLastInboundAssociation TimeTicks
  exchmtaconnLastOutboundAssociation TimeTicks
  exchmtaconnRejectedInboundAssociations INTEGER
  exchmtaconnFailedOutboundAssociations INTEGER
  exchmtaconnNextAssociationRetry INTEGER
  exchmtaconnInboundRejectReason INTEGER
  exchmtaconnOutboundFailureReason INTEGER
  exchmtaconnInboundMessagesTotal Counter
  exchmtaconnOutboundMessagesTotal Counter
  exchmtaconnInboundBytesTotal Counter
  exchmtaconnQueuedBytes Counter
  exchmtaconnOutboundBytesTotal Counter
  exchmtaconnTotalRecipientsInbound Counter
  exchmtaconnTotalRecipientsOutbound Counter

RasportrAS-PortEntry  
SEQUENCE    
  rasportrAS-PortIndex INTEGER
  rasportrAS-PortInstance DisplayString
  rasportBytesTransmitted INTEGER
  rasportBytesReceived INTEGER
  rasportFramesTransmitted INTEGER
  rasportFramesReceived INTEGER
  rasportPercentCompressionOut INTEGER
  rasportPercentCompressionIn INTEGER
  rasportCRCErrors INTEGER
  rasportTimeoutErrors INTEGER
  rasportSerialOverrunErrors INTEGER
  rasportAlignmentErrors INTEGER
  rasportBufferOverrunErrors INTEGER
  rasportTotalErrors INTEGER
  rasportBytesTransmittedPerSec Counter
  rasportBytesReceivedPerSec Counter
  rasportFramesTransmittedPerSec Counter
  rasportFramesReceivedPerSec Counter
  rasportTotalErrorsPerSec Counter


Webserviceweb-ServiceEntry  
SEQUENCE    
  webserviceweb-ServiceIndex INTEGER
  webserviceweb-ServiceInstance DisplayString
  webserviceBytesSentPerSec INTEGER
  webserviceBytesReceivedPerSec INTEGER
  webserviceBytesTotalPerSec INTEGER
  webserviceTotalFilesSent INTEGER
  webserviceFilesSentPerSec Counter
  webserviceTotalFilesReceived INTEGER
  webserviceFilesReceivedPerSec Counter
  webserviceTotalFilesTransferred INTEGER
  webserviceFilesPerSec Counter
  webserviceCurrentAnonymousUsers INTEGER
  webserviceCurrentNonAnonymousUsers INTEGER
  webserviceTotalAnonymousUsers INTEGER
  webserviceAnonymousUsersPerSec Counter
  webserviceTotalNonAnonymousUsers INTEGER
  webserviceNonAnonymousUsersPerSec Counter
  webserviceMaximumAnonymousUsers INTEGER
  webserviceMaximumNonAnonymousUsers INTEGER
  webserviceCurrentConnections INTEGER
  webserviceMaximumConnections INTEGER
  webserviceTotalConnectionAttempts INTEGER
  webserviceConnectionAttemptsPerSec Counter
  webserviceTotalLogonAttempts INTEGER
  webserviceLogonAttemptsPerSec Counter
  webserviceTotalGetRequests INTEGER
  webserviceGetRequestsPerSec Counter
  webserviceTotalPostRequests INTEGER
  webservicePostRequestsPerSec Counter
  webserviceTotalHeadRequests INTEGER
  webserviceHeadRequestsPerSec Counter
  webserviceTotalPutRequests INTEGER
  webservicePutRequestsPerSec Counter
  webserviceTotalDeleteRequests INTEGER
  webserviceDeleteRequestsPerSec Counter
  webserviceTotalTraceRequests INTEGER
  webserviceSystemCodeResidentBytes Counter
  webserviceTotalOtherRequestMethods INTEGER
  webserviceOtherRequestMethodsPerSec Counter
  webserviceTotalMethodRequests INTEGER
  webserviceTotalMethodRequestsPerSec Counter
  webserviceTotalCGIRequests INTEGER
  webserviceCGIRequestsPerSec Counter
  webserviceTotalISAPIExtensionRequests INTEGER
  webserviceISAPIExtensionRequestsPerSec Counter
  webserviceTotalNotFoundErrors INTEGER
  webserviceNotFoundErrorsPerSec Counter
  webserviceCurrentCGIRequests INTEGER
  webserviceCurrentISAPIExtensionRequests INTEGER
  webserviceMaximumCGIRequests INTEGER
  webserviceMaximumISAPIExtensionRequests INTEGER
  webserviceTotalBlockedAsyncIPerORequests INTEGER
  webserviceTotalAllowedAsyncIPerORequests INTEGER
  webserviceTotalRejectedAsyncIPerORequests INTEGER
  webserviceCurrentBlockedAsyncIPerORequests INTEGER
  webserviceMeasuredAsyncIPerOBandwidthUsage INTEGER

Defined Values

microsoft 1.3.6.1.4.1.311
OBJECT IDENTIFIER    

software 1.3.6.1.4.1.311.1
OBJECT IDENTIFIER    

systems 1.3.6.1.4.1.311.1.1
OBJECT IDENTIFIER    

os 1.3.6.1.4.1.311.1.1.3
OBJECT IDENTIFIER    

winnt 1.3.6.1.4.1.311.1.1.3.1
OBJECT IDENTIFIER    

performance 1.3.6.1.4.1.311.1.1.3.1.1
OBJECT IDENTIFIER    

memory 1.3.6.1.4.1.311.1.1.3.1.1.1
OBJECT IDENTIFIER    

memoryAvailableBytes 1.3.6.1.4.1.311.1.1.3.1.1.1.1
Available Bytes displays the size of the virtual memory currently on the Zeroed, Free, and Standby lists. Zeroed and Free memory is ready for use, with Zeroed memory cleared to zeros. Standby memory is memory removed from a process's Working Set but still available. Notice that this is an instantaneous count, not an average over the time interval.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER  

memoryCommittedBytes 1.3.6.1.4.1.311.1.1.3.1.1.1.2
Committed Bytes displays the size of virtual memory (in bytes) that has been Committed (as opposed to simply reserved). Committed memory must have backing (i.e., disk) storage available, or must be assured never to need disk storage (because main memory is large enough to hold it.) Notice that this is an instantaneous count, not an average over the time interval.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER  

memoryCommitLimit 1.3.6.1.4.1.311.1.1.3.1.1.1.3
Commit Limit is the size (in bytes) of virtual memory that can be committed without having to extend the paging file(s). If the paging file(s) can be extended, this is a soft limit.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER  

memoryPageFaultsPerSec 1.3.6.1.4.1.311.1.1.3.1.1.1.4
Page Faults/sec is a count of the Page Faults in the processor. A page fault occurs when a process refers to a virtual memory page that is not in its Working Set in main memory. A Page Fault will not cause the page to be fetched from disk if that page is on the standby list, and hence already in main memory, or if it is in use by another process with whom the page is shared.
Status: mandatory Access: read-only
OBJECT-TYPE    
  Counter  

memoryWriteCopiesPerSec 1.3.6.1.4.1.311.1.1.3.1.1.1.5
Write Copies/sec is the number of page faults that have been satisfied by making a copy of a page when an attempt to write to the page is made. This is an economical way of sharing data since the copy of the page is only made on an attempt to write to the page; otherwise, the page is shared.
Status: mandatory Access: read-only
OBJECT-TYPE    
  Counter  

memoryTransitionFaultsPerSec 1.3.6.1.4.1.311.1.1.3.1.1.1.6
Transition Faults/sec is the number of page faults resolved by recovering pages that were in transition, i.e., being written to disk at the time of the page fault. The pages were recovered without additional disk activity.
Status: mandatory Access: read-only
OBJECT-TYPE    
  Counter  

memoryCacheFaultsPerSec 1.3.6.1.4.1.311.1.1.3.1.1.1.7
Cache Faults occur whenever the Cache manager does not find a file's page in the immediate Cache and must ask the memory manager to locate the page elsewhere in memory or on the disk so that it can be loaded into the immediate Cache.
Status: mandatory Access: read-only
OBJECT-TYPE    
  Counter  

memoryDemandZeroFaultsPerSec 1.3.6.1.4.1.311.1.1.3.1.1.1.8
Demand Zero Faults are the number of page faults for pages that must be filled with zeros before the fault is satisfied. If the Zeroed list is not empty, the fault can be resolved by removing a page from the Zeroed list.
Status: mandatory Access: read-only
OBJECT-TYPE    
  Counter  

memoryPagesPerSec 1.3.6.1.4.1.311.1.1.3.1.1.1.9
Pages/sec is the number of pages read from the disk or written to the disk to resolve memory references to pages that were not in memory at the time of the reference. This is the sum of Pages Input/sec and Pages Output/sec. This counter includes paging traffic on behalf of the system Cache to access file data for applications. This value also includes the pages to/from non-cached mapped memory files. This is the primary counter to observe if you are concerned about excessive memory pressure (that is, thrashing), and the excessive paging that may result.
Status: mandatory Access: read-only
OBJECT-TYPE    
  Counter  

memoryPagesInputPerSec 1.3.6.1.4.1.311.1.1.3.1.1.1.10
Pages Input/sec is the number of pages read from the disk to resolve memory references to pages that were not in memory at the time of the reference. This counter includes paging traffic on behalf of the system Cache to access file data for applications. This is an important counter to observe if you are concerned about excessive memory pressure (that is, thrashing), and the excessive paging that may result.
Status: mandatory Access: read-only
OBJECT-TYPE    
  Counter  

memoryPageReadsPerSec 1.3.6.1.4.1.311.1.1.3.1.1.1.11
Page Reads/sec is the number of times the disk was read to retrieve pages of virtual memory necessary to resolve page faults. Multiple pages can be read during a disk read operation.
Status: mandatory Access: read-only
OBJECT-TYPE    
  Counter  

memoryPagesOutputPerSec 1.3.6.1.4.1.311.1.1.3.1.1.1.12
Pages Output/sec is a count of the number of pages that are written to disk because the pages have been modified in main memory.
Status: mandatory Access: read-only
OBJECT-TYPE    
  Counter  

memoryPageWritesPerSec 1.3.6.1.4.1.311.1.1.3.1.1.1.13
Page Writes/sec is a count of the number of times pages have been written to the disk because they were changed since last retrieved. Each such write operation may transfer a number of pages.
Status: mandatory Access: read-only
OBJECT-TYPE    
  Counter  

memoryPoolPagedBytes 1.3.6.1.4.1.311.1.1.3.1.1.1.14
Pool Paged Bytes is the number of bytes in the Paged Pool, a system memory area where space is acquired by operating system components as they accomplish their appointed tasks. Paged Pool pages can be paged out to the paging file when not accessed by the system for sustained periods of time.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER  

memoryPoolNonpagedBytes 1.3.6.1.4.1.311.1.1.3.1.1.1.15
Pool Nonpaged Bytes is the number of bytes in the Nonpaged Pool, a system memory area where space is acquired by operating system components as they accomplish their appointed tasks. Nonpaged Pool pages cannot be paged out to the paging file, but instead remain in main memory as long as they are allocated.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER  

memoryPoolPagedAllocs 1.3.6.1.4.1.311.1.1.3.1.1.1.16
Pool Paged Allocs is the number of calls to allocate space in the system Paged Pool. Paged Pool is a system memory area where space is acquired by operating system components as they accomplish their appointed tasks. Paged Pool pages can be paged out to the paging file when not accessed by the system for sustained periods of time.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER  

memoryPoolNonpagedAllocs 1.3.6.1.4.1.311.1.1.3.1.1.1.17
Pool Nonpaged Allocs is the number of calls to allocate space in the system Nonpaged Pool. Nonpaged Pool is a system memory area where space is acquired by operating system components as they accomplish their appointed tasks. Nonpaged Pool pages cannot be paged out to the paging file, but instead remain in main memory as long as they are allocated.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER  

memoryFreeSystemPageTableEntries 1.3.6.1.4.1.311.1.1.3.1.1.1.18
The number of Page Table Entries not currently in use by the system.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER  

memoryCacheBytes 1.3.6.1.4.1.311.1.1.3.1.1.1.19
Cache Bytes measures the number of bytes currently in use by the system Cache. The system Cache is used to buffer data retrieved from disk or LAN. The system Cache uses memory not in use by active processes in the computer.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER  

memoryCacheBytesPeak 1.3.6.1.4.1.311.1.1.3.1.1.1.20
Cache Bytes Peak measures the maximum number of bytes used by the system Cache. The system Cache is used to buffer data retrieved from disk or LAN. The system Cache uses memory not in use by active processes in the computer.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER  

memoryPoolPagedResidentBytes 1.3.6.1.4.1.311.1.1.3.1.1.1.21
Pool Paged Resident Bytes is the size of paged Pool resident in core memory. This is the actual cost of the paged Pool allocation, since this is actively in use and using real physical memory.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER  

memorySystemCodeTotalBytes 1.3.6.1.4.1.311.1.1.3.1.1.1.22
System Code Total Bytes is the number of bytes of pagable pages in ntoskrnl.exe, hal.dll, and the boot drivers and file systems loaded by ntldr/osloader.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER  

memorySystemCodeResidentBytes 1.3.6.1.4.1.311.1.1.3.1.1.1.23
System Code Resident Bytes is the number of bytes of System Code Total Bytes currently resident in core memory. This is the code working set of the pagable executive. In addition to this, there is another ~300k bytes of non-paged kernel code.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER  

memorySystemDriverTotalBytes 1.3.6.1.4.1.311.1.1.3.1.1.1.24
System Driver Total Bytes is the number of bytes of pagable pages in all other loaded device drivers.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER  

memorySystemDriverResidentBytes 1.3.6.1.4.1.311.1.1.3.1.1.1.25
System Driver Resident Bytes is the number of bytes of System Driver Total Bytes currently resident in core memory. This number is the code working set of the pagable drivers. In addition to this, there is another ~700k bytes of non-paged driver code.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER  

memorySystemCacheResidentBytes 1.3.6.1.4.1.311.1.1.3.1.1.1.26
System Cache Resident Bytes is the number of bytes currently resident in the global disk cache.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER  

memoryPercentCommittedBytesInUse 1.3.6.1.4.1.311.1.1.3.1.1.1.27
% Committed Bytes In Use is the ratio of the Commited Bytes to the Commit Limit. This represents the amount of available virtual memory in use. Note that the Commit Limit may change if the paging file is extended. This is an instantaneous value, not an average.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER  

cpuprocessorTable 1.3.6.1.4.1.311.1.1.3.1.1.2
A table containing performance information for instances of 'processor' objects.
Status: mandatory Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    CpuprocessorEntry

cpuprocessorEntry 1.3.6.1.4.1.311.1.1.3.1.1.2.1
Performance information for one particular instance of 'processor' object.
Status: mandatory Access: not-accessible
OBJECT-TYPE    
  CpuprocessorEntry  

cpuprocessorIndex 1.3.6.1.4.1.311.1.1.3.1.1.2.1.1
Index.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER  

cpuprocessorInstance 1.3.6.1.4.1.311.1.1.3.1.1.2.1.2
Instance name.
Status: mandatory Access: read-only
OBJECT-TYPE    
  DisplayString  

cpuPercentProcessorTime 1.3.6.1.4.1.311.1.1.3.1.1.2.1.3
Processor Time is expressed as a percentage of the elapsed time that a processor is busy executing a non-Idle thread. It can be viewed as the fraction of the time spent doing useful work. Each processor is assigned an Idle thread in the Idle process which consumes those unproductive processor cycles not used by any other threads.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER  

cpuPercentUserTime 1.3.6.1.4.1.311.1.1.3.1.1.2.1.4
User Time is the percentage of processor time spent in User Mode in non-Idle threads. All application code and subsystem code execute in User Mode. The graphics engine, graphics device drivers, printer device drivers, and the window manager also execute in User Mode. Code executing in User Mode cannot damage the integrity of the Windows NT Executive, Kernel, and device drivers. Unlike some early operating systems, Windows NT uses process boundaries for subsystem protection in addition to the traditional protection of User and Privileged modes. These subsystem processes provide additional protection. Therefore, some work done by Windows NT on behalf of your application may appear in other subsystem processes in addition to the Privileged Time in your process.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER  

cpuPercentPrivilegedTime 1.3.6.1.4.1.311.1.1.3.1.1.2.1.5
Privileged Time is the percentage of processor time spent in Privileged Mode in non-Idle threads. The Windows NT service layer, the Executive routines, and the Windows NT Kernel execute in Privileged Mode. Device drivers for most devices other than graphics adapters and printers also execute in Privileged Mode. Unlike some early operating systems, Windows NT uses process boundaries for subsystem protection in addition to the traditional protection of User and Privileged modes. These subsystem processes provide additional protection. Therefore, some work done by Windows NT on behalf of your application may appear in other subsystem processes in addition to the Privileged Time in your process.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER  

cpuInterruptsPerSec 1.3.6.1.4.1.311.1.1.3.1.1.2.1.6
Interrupts/sec is the number of device interrupts the processor is experiencing. A device interrupts the processor when it has completed a task or when it otherwise requires attention. Normal thread execution is suspended during interrupts. An interrupt may cause the processor to switch to another, higher priority thread. Clock interrupts are frequent and periodic and create a background of interrupt activity.
Status: mandatory Access: read-only
OBJECT-TYPE    
  Counter  

cpuPercentDPCTime 1.3.6.1.4.1.311.1.1.3.1.1.2.1.7
% DPC Time is the percentage of elapsed time that the Processor spent in Deferred Procedure Calls. When a hardware device interrupts the Processor, the Interrupt Handler may elect to execute the majority of its work in a DPC. DPC's run at lower priority than Interrupts, and so permit Interrupts to occur while DPC's being execute. Deferred Procedure Calls are executed in Privileged Mode, so this is a component of Processor: % Privileged Time. This counter can help determine the source of excessive time being spent in Privileged Mode.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER  

cpuPercentInterruptTime 1.3.6.1.4.1.311.1.1.3.1.1.2.1.8
% Interrupt Time is the percentage of elapsed time that the Processor spent handling hardware Interrupts. When a hardware device interrupts the Processor, the Interrupt Handler will execute to handle the condition, usually by signaling I/O completion and possibly issuing another pending I/O request. Some of this work may be done in a Deferred Procedure Call (see % DPC Time.) However, time spent in DPC's is not counted as time in Interrupts. Interrupts are executed in Privileged Mode, so this is a component of Processor: % Privileged Time. This counter can help determine the source of excessive time being spent in Privileged Mode.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER  

cpuDPCsQueuedPerSec 1.3.6.1.4.1.311.1.1.3.1.1.2.1.9
DPCs Queued/sec is the rate DPC objects are queued to this processor's DPC queue.
Status: mandatory Access: read-only
OBJECT-TYPE    
  Counter  

cpuDPCRate 1.3.6.1.4.1.311.1.1.3.1.1.2.1.10
DPC Rate is the average rate DPC objects are queued to this processor's DPC queue per clock tick.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER  

cpuDPCBypassesPerSec 1.3.6.1.4.1.311.1.1.3.1.1.2.1.11
DPC Bypasses/sec is the rate Dispatch interrupts were short-circuited.
Status: mandatory Access: read-only
OBJECT-TYPE    
  Counter  

cpuAPCBypassesPerSec 1.3.6.1.4.1.311.1.1.3.1.1.2.1.12
APC Bypasses/sec is the rate kernel APC interrupts were short-circuited.
Status: mandatory Access: read-only
OBJECT-TYPE    
  Counter  

netnetwork-InterfaceTable 1.3.6.1.4.1.311.1.1.3.1.1.3
A table containing performance information for instances of 'network-Interface' objects.
Status: mandatory Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    Netnetwork-InterfaceEntry

netnetwork-InterfaceEntry 1.3.6.1.4.1.311.1.1.3.1.1.3.1
Performance information for one particular instance of 'network-Interface' object.
Status: mandatory Access: not-accessible
OBJECT-TYPE    
  Netnetwork-InterfaceEntry  

netnetwork-InterfaceIndex 1.3.6.1.4.1.311.1.1.3.1.1.3.1.1
Index.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER  

netnetwork-InterfaceInstance 1.3.6.1.4.1.311.1.1.3.1.1.3.1.2
Instance name.
Status: mandatory Access: read-only
OBJECT-TYPE    
  DisplayString  

netBytesTotalPerSec 1.3.6.1.4.1.311.1.1.3.1.1.3.1.3
Bytes Total/sec is the rate that bytes are sent and received on the interface, including framing characters.
Status: mandatory Access: read-only
OBJECT-TYPE    
  Counter  

netPacketsPerSec 1.3.6.1.4.1.311.1.1.3.1.1.3.1.4
Packets/sec is the rate that packets are sent and received on the network interface.
Status: mandatory Access: read-only
OBJECT-TYPE    
  Counter  

netPacketsReceivedPerSec 1.3.6.1.4.1.311.1.1.3.1.1.3.1.5
Packets Received/sec is the rate that packets are received on the network interface.
Status: mandatory Access: read-only
OBJECT-TYPE    
  Counter  

netPacketsSentPerSec 1.3.6.1.4.1.311.1.1.3.1.1.3.1.6
Packets Sent/sec is the rate that packets are sent on the network interface.
Status: mandatory Access: read-only
OBJECT-TYPE    
  Counter  

netCurrentBandwidth 1.3.6.1.4.1.311.1.1.3.1.1.3.1.7
Current Bandwidth is an estimate of the interface's current bandwidth in bits per second (bps). For interfaces that do not vary in bandwidth or for those where no accurate estimation can be made, this value is the nominal bandwidth.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER  

netBytesReceivedPerSec 1.3.6.1.4.1.311.1.1.3.1.1.3.1.8
Bytes Received/sec is the rate that bytes are received on the interface, including framing characters.
Status: mandatory Access: read-only
OBJECT-TYPE    
  Counter  

netPacketsReceivedUnicastPerSec 1.3.6.1.4.1.311.1.1.3.1.1.3.1.9
Packets Received Unicast/sec is the rate that (subnet) unicast packets are delivered to a higher-layer protocol.
Status: mandatory Access: read-only
OBJECT-TYPE    
  Counter  

netPacketsReceivedNon-UnicastPerSec 1.3.6.1.4.1.311.1.1.3.1.1.3.1.10
Packets Received Non-Unicast/sec is the rate that non-unicast (i.e., subnet broadcast or subnet multicast) packets are delivered to a higher-layer protocol.
Status: mandatory Access: read-only
OBJECT-TYPE    
  Counter  

netPacketsReceivedDiscarded 1.3.6.1.4.1.311.1.1.3.1.1.3.1.11
Packets Received Discarded is the number of inbound packets that were chosen to be discarded even though no errors had been detected to prevent their being deliverable to a higher-layer protocol. One possible reason for discarding such a packet could be to free up buffer space.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER  

netPacketsReceivedErrors 1.3.6.1.4.1.311.1.1.3.1.1.3.1.12
Packets Received Errors is the number of inbound packets that contained errors preventing them from being deliverable to a higher-layer protocol.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER  

netPacketsReceivedUnknown 1.3.6.1.4.1.311.1.1.3.1.1.3.1.13
Packets Received Unknown is the number of packets received via the interface that were discarded because of an unknown or unsupported protocol.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER  

netBytesSentPerSec 1.3.6.1.4.1.311.1.1.3.1.1.3.1.14
Bytes Sent/sec is the rate that bytes are sent on the interface, including framing characters.
Status: mandatory Access: read-only
OBJECT-TYPE    
  Counter  

netPacketsSentUnicastPerSec 1.3.6.1.4.1.311.1.1.3.1.1.3.1.15
Packets Sent Unicast/sec is the rate that packets are requested to be transmitted to subnet-unicast addresses by higher-level protocols. The rate includes the packets that were discarded or not sent.
Status: mandatory Access: read-only
OBJECT-TYPE    
  Counter  

netPacketsSentNon-UnicastPerSec 1.3.6.1.4.1.311.1.1.3.1.1.3.1.16
Packets Sent Non-Unicast/sec is the rate that packets are requested to be transmitted to non-unicast (i.e., subnet broadcast or subnet multicast) addresses by higher-level protocols. The rate includes the packets that were discarded or not sent.
Status: mandatory Access: read-only
OBJECT-TYPE    
  Counter  

netPacketsOutboundDiscarded 1.3.6.1.4.1.311.1.1.3.1.1.3.1.17
Packets Outbound Discarded is the number of outbound packets that were chosen to be discarded even though no errors had been detected to prevent their being transmitted. One possible reason for discarding such a packet could be to free up buffer space.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER  

netPacketsOutboundErrors 1.3.6.1.4.1.311.1.1.3.1.1.3.1.18
Packets Outbound Errors is the number of outbound packets that could not be transmitted because of errors.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER  

netOutputQueueLength 1.3.6.1.4.1.311.1.1.3.1.1.3.1.19
Output Queue Length is the length of the output packet queue (in packets.) If this is longer than 2, delays are being experienced and the bottleneck should be found and eliminated if possible. Since the requests are queued by NDIS in this implementations, this will always be 0.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER  

pdiskphysicalDiskTable 1.3.6.1.4.1.311.1.1.3.1.1.4
A table containing performance information for instances of 'physicalDisk' objects.
Status: mandatory Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    PdiskphysicalDiskEntry

pdiskphysicalDiskEntry 1.3.6.1.4.1.311.1.1.3.1.1.4.1
Performance information for one particular instance of 'physicalDisk' object.
Status: mandatory Access: not-accessible
OBJECT-TYPE    
  PdiskphysicalDiskEntry  

pdiskphysicalDiskIndex 1.3.6.1.4.1.311.1.1.3.1.1.4.1.1
Index.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER  

pdiskphysicalDiskInstance 1.3.6.1.4.1.311.1.1.3.1.1.4.1.2
Instance name.
Status: mandatory Access: read-only
OBJECT-TYPE    
  DisplayString  

pdiskCurrentDiskQueueLength 1.3.6.1.4.1.311.1.1.3.1.1.4.1.3
Current Disk Queue Length is the number of requests outstanding on the disk at the time the performance data is collected. It includes requests in service at the time of the snapshot. This is an instantaneous length, not an average over the time interval. Multi-spindle disk devices can have multiple requests active at one time, but other concurrent requests are awaiting service. This counter may reflect a transitory high or low queue length, but if there is a sustained load on the disk drive, it is likely that this will be consistently high. Requests are experiencing delays proportional to the length of this queue minus the number of spindles on the disks. This difference should average less than 2 for good performance.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER  

pdiskPercentDiskTime 1.3.6.1.4.1.311.1.1.3.1.1.4.1.4
Disk Time is the percentage of elapsed time that the selected disk drive is busy servicing read or write requests.
Status: mandatory Access: read-only
OBJECT-TYPE    
  TimeTicks  

pdiskAvgDiskQueueLength 1.3.6.1.4.1.311.1.1.3.1.1.4.1.5
Avg. Disk Queue Length is the average number of both read and write requests that were queued for the selected disk during the sample interval.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER  

pdiskPercentDiskReadTime 1.3.6.1.4.1.311.1.1.3.1.1.4.1.6
Disk Read Time is the percentage of elapsed time that the selected disk drive is busy servicing read requests.
Status: mandatory Access: read-only
OBJECT-TYPE    
  TimeTicks  

pdiskAvgDiskReadQueueLength 1.3.6.1.4.1.311.1.1.3.1.1.4.1.7
Avg. Disk Read Queue Length is the average number of read requests that were queued for the selected disk during the sample interval.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER  

pdiskPercentDiskWriteTime 1.3.6.1.4.1.311.1.1.3.1.1.4.1.8
Disk Write Time is the percentage of elapsed time that the selected disk drive is busy servicing write requests.
Status: mandatory Access: read-only
OBJECT-TYPE    
  TimeTicks  

pdiskAvgDiskWriteQueueLength 1.3.6.1.4.1.311.1.1.3.1.1.4.1.9
Avg. Disk Write Queue Length is the average number of write requests that were queued for the selected disk during the sample interval.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER  

pdiskAvgDiskSecPerTransfer 1.3.6.1.4.1.311.1.1.3.1.1.4.1.10
Avg. Disk sec/Transfer is the time in seconds of the average disk transfer.
Status: mandatory Access: read-only
OBJECT-TYPE    
  TimeTicks  

pdiskAvgDiskSecPerRead 1.3.6.1.4.1.311.1.1.3.1.1.4.1.11
Avg. Disk sec/Read is the average time in seconds of a read of data from the disk.
Status: mandatory Access: read-only
OBJECT-TYPE    
  TimeTicks  

pdiskAvgDiskSecPerWrite 1.3.6.1.4.1.311.1.1.3.1.1.4.1.12
Avg. Disk sec/Write is the average time in seconds of a write of data to the disk.
Status: mandatory Access: read-only
OBJECT-TYPE    
  TimeTicks  

pdiskDiskTransfersPerSec 1.3.6.1.4.1.311.1.1.3.1.1.4.1.13
Disk Transfers/sec is the rate of read and write operations on the disk.
Status: mandatory Access: read-only
OBJECT-TYPE    
  Counter  

pdiskDiskReadsPerSec 1.3.6.1.4.1.311.1.1.3.1.1.4.1.14
Disk Reads/sec is the rate of read operations on the disk.
Status: mandatory Access: read-only
OBJECT-TYPE    
  Counter  

pdiskDiskWritesPerSec 1.3.6.1.4.1.311.1.1.3.1.1.4.1.15
Disk Writes/sec is the rate of write operations on the disk.
Status: mandatory Access: read-only
OBJECT-TYPE    
  Counter  

pdiskDiskBytesPerSec 1.3.6.1.4.1.311.1.1.3.1.1.4.1.16
Disk Bytes/sec is the rate bytes are transferred to or from the disk during write or read operations.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER  

pdiskDiskReadBytesPerSec 1.3.6.1.4.1.311.1.1.3.1.1.4.1.17
Disk Read Bytes/sec is the rate bytes are transferred from the disk during read operations.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER  

pdiskDiskWriteBytesPerSec 1.3.6.1.4.1.311.1.1.3.1.1.4.1.18
Disk Write Bytes is rate bytes are transferred to the disk during write operations.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER  

ldisklogicalDiskTable 1.3.6.1.4.1.311.1.1.3.1.1.5
A table containing performance information for instances of 'logicalDisk' objects.
Status: mandatory Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    LdisklogicalDiskEntry

ldisklogicalDiskEntry 1.3.6.1.4.1.311.1.1.3.1.1.5.1
Performance information for one particular instance of 'logicalDisk' object.
Status: mandatory Access: not-accessible
OBJECT-TYPE    
  LdisklogicalDiskEntry  

ldisklogicalDiskIndex 1.3.6.1.4.1.311.1.1.3.1.1.5.1.1
Index.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER  

ldisklogicalDiskInstance 1.3.6.1.4.1.311.1.1.3.1.1.5.1.2
Instance name.
Status: mandatory Access: read-only
OBJECT-TYPE    
  DisplayString  

ldiskPercentFreeSpace 1.3.6.1.4.1.311.1.1.3.1.1.5.1.3
Percent Free Space is the ratio of the free space available on the logical disk unit to the total usable space provided by the selected logical disk drive
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER  

ldiskFreeMegabytes 1.3.6.1.4.1.311.1.1.3.1.1.5.1.4
Free Megabytes displays the unallocated space on the disk drive in megabytes. One megabyte = 1,048,576 bytes.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER  

ldiskCurrentDiskQueueLength 1.3.6.1.4.1.311.1.1.3.1.1.5.1.5
Current Disk Queue Length is the number of requests outstanding on the disk at the time the performance data is collected. It includes requests in service at the time of the snapshot. This is an instantaneous length, not an average over the time interval. Multi-spindle disk devices can have multiple requests active at one time, but other concurrent requests are awaiting service. This counter may reflect a transitory high or low queue length, but if there is a sustained load on the disk drive, it is likely that this will be consistently high. Requests are experiencing delays proportional to the length of this queue minus the number of spindles on the disks. This difference should average less than 2 for good performance.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER  

ldiskPercentDiskTime 1.3.6.1.4.1.311.1.1.3.1.1.5.1.6
Disk Time is the percentage of elapsed time that the selected disk drive is busy servicing read or write requests.
Status: mandatory Access: read-only
OBJECT-TYPE    
  TimeTicks  

ldiskAvgDiskQueueLength 1.3.6.1.4.1.311.1.1.3.1.1.5.1.7
Avg. Disk Queue Length is the average number of both read and write requests that were queued for the selected disk during the sample interval.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER  

ldiskPercentDiskReadTime 1.3.6.1.4.1.311.1.1.3.1.1.5.1.8
Disk Read Time is the percentage of elapsed time that the selected disk drive is busy servicing read requests.
Status: mandatory Access: read-only
OBJECT-TYPE    
  TimeTicks  

ldiskAvgDiskReadQueueLength 1.3.6.1.4.1.311.1.1.3.1.1.5.1.9
Avg. Disk Read Queue Length is the average number of read requests that were queued for the selected disk during the sample interval.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER  

ldiskPercentDiskWriteTime 1.3.6.1.4.1.311.1.1.3.1.1.5.1.10
Disk Write Time is the percentage of elapsed time that the selected disk drive is busy servicing write requests.
Status: mandatory Access: read-only
OBJECT-TYPE    
  TimeTicks  

ldiskAvgDiskWriteQueueLength 1.3.6.1.4.1.311.1.1.3.1.1.5.1.11
Avg. Disk Write Queue Length is the average number of write requests that were queued for the selected disk during the sample interval.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER  

ldiskAvgDiskSecPerTransfer 1.3.6.1.4.1.311.1.1.3.1.1.5.1.12
Avg. Disk sec/Transfer is the time in seconds of the average disk transfer.
Status: mandatory Access: read-only
OBJECT-TYPE    
  TimeTicks  

ldiskAvgDiskSecPerRead 1.3.6.1.4.1.311.1.1.3.1.1.5.1.13
Avg. Disk sec/Read is the average time in seconds of a read of data from the disk.
Status: mandatory Access: read-only
OBJECT-TYPE    
  TimeTicks  

ldiskAvgDiskSecPerWrite 1.3.6.1.4.1.311.1.1.3.1.1.5.1.14
Avg. Disk sec/Write is the average time in seconds of a write of data to the disk.
Status: mandatory Access: read-only
OBJECT-TYPE    
  TimeTicks  

ldiskDiskTransfersPerSec 1.3.6.1.4.1.311.1.1.3.1.1.5.1.15
Disk Transfers/sec is the rate of read and write operations on the disk.
Status: mandatory Access: read-only
OBJECT-TYPE    
  Counter  

ldiskDiskReadsPerSec 1.3.6.1.4.1.311.1.1.3.1.1.5.1.16
Disk Reads/sec is the rate of read operations on the disk.
Status: mandatory Access: read-only
OBJECT-TYPE    
  Counter  

ldiskDiskWritesPerSec 1.3.6.1.4.1.311.1.1.3.1.1.5.1.17
Disk Writes/sec is the rate of write operations on the disk.
Status: mandatory Access: read-only
OBJECT-TYPE    
  Counter  

ldiskDiskBytesPerSec 1.3.6.1.4.1.311.1.1.3.1.1.5.1.18
Disk Bytes/sec is the rate bytes are transferred to or from the disk during write or read operations.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER  

ldiskDiskReadBytesPerSec 1.3.6.1.4.1.311.1.1.3.1.1.5.1.19
Disk Read Bytes/sec is the rate bytes are transferred from the disk during read operations.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER  

ldiskDiskWriteBytesPerSec 1.3.6.1.4.1.311.1.1.3.1.1.5.1.20
Disk Write Bytes is rate bytes are transferred to the disk during write operations.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER  

pagefilepaging-FileTable 1.3.6.1.4.1.311.1.1.3.1.1.6
A table containing performance information for instances of 'paging-File' objects.
Status: mandatory Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    Pagefilepaging-FileEntry

pagefilepaging-FileEntry 1.3.6.1.4.1.311.1.1.3.1.1.6.1
Performance information for one particular instance of 'paging-File' object.
Status: mandatory Access: not-accessible
OBJECT-TYPE    
  Pagefilepaging-FileEntry  

pagefilepaging-FileIndex 1.3.6.1.4.1.311.1.1.3.1.1.6.1.1
Index.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER  

pagefilepaging-FileInstance 1.3.6.1.4.1.311.1.1.3.1.1.6.1.2
Instance name.
Status: mandatory Access: read-only
OBJECT-TYPE    
  DisplayString  

pagefilePercentUsage 1.3.6.1.4.1.311.1.1.3.1.1.6.1.3
The amount of the Page File instance in use in percent. See also Process:Page File Bytes.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER  

pagefilePercentUsagePeak 1.3.6.1.4.1.311.1.1.3.1.1.6.1.4
The peak usage of the Page File instance in percent. See also Process:Page File Bytes Peak.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER  

processprocessTable 1.3.6.1.4.1.311.1.1.3.1.1.7
A table containing performance information for instances of 'process' objects.
Status: mandatory Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    ProcessprocessEntry

processprocessEntry 1.3.6.1.4.1.311.1.1.3.1.1.7.1
Performance information for one particular instance of 'process' object.
Status: mandatory Access: not-accessible
OBJECT-TYPE    
  ProcessprocessEntry  

processprocessIndex 1.3.6.1.4.1.311.1.1.3.1.1.7.1.1
Index.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER  

processprocessInstance 1.3.6.1.4.1.311.1.1.3.1.1.7.1.2
Instance name.
Status: mandatory Access: read-only
OBJECT-TYPE    
  DisplayString  

processPercentProcessorTime 1.3.6.1.4.1.311.1.1.3.1.1.7.1.3
Processor Time is the percentage of elapsed time that all of the threads of this process used the processor to execute instructions. An instruction is the basic unit of execution in a computer, a thread is the object that executes instructions, and a process is the object created when a program is run. Code executed to handle certain hardware interrupts or trap conditions may be counted for this process.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER  

processPercentUserTime 1.3.6.1.4.1.311.1.1.3.1.1.7.1.4
User Time is the percentage of elapsed time that this process's threads have spent executing code in User Mode. Applications execute in User Mode, as do subsystems like the window manager and the graphics engine. Code executing in User Mode cannot damage the integrity of the Windows NT Executive, Kernel, and device drivers. Unlike some early operating systems, Windows NT uses process boundaries for subsystem protection in addition to the traditional protection of User and Privileged modes. These subsystem processes provide additional protection. Therefore, some work done by Windows NT on behalf of your application may appear in other subsystem processes in addition to the Privileged Time in your process.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER  

processPercentPrivilegedTime 1.3.6.1.4.1.311.1.1.3.1.1.7.1.5
Privileged Time is the percentage of elapsed time that this process's threads have spent executing code in Privileged Mode. When a Windows NT system service is called, the service will often run in Privileged Mode to gain access to system-private data. Such data is protected from access by threads executing in User Mode. Calls to the system may be explicit, or they may be implicit such as when a page fault or an interrupt occurs. Unlike some early operating systems, Windows NT uses process boundaries for subsystem protection in addition to the traditional protection of User and Privileged modes. These subsystem processes provide additional protection. Therefore, some work done by Windows NT on behalf of your application may appear in other subsystem processes in addition to the Privileged Time in your process.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER  

processVirtualBytesPeak 1.3.6.1.4.1.311.1.1.3.1.1.7.1.6
Virtual Bytes Peak is the maximum number of bytes of virtual address space the process has used at any one time. Use of virtual address space does not necessarily imply corresponding use of either disk or main memory pages. Virtual space is however finite, and by using too much, the process may limit its ability to load libraries.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER  

processVirtualBytes 1.3.6.1.4.1.311.1.1.3.1.1.7.1.7
Virtual Bytes is the current size in bytes of the virtual address space the process is using. Use of virtual address space does not necessarily imply corresponding use of either disk or main memory pages. Virtual space is however finite, and by using too much, the process may limit its ability to load libraries.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER  

processPageFaultsPerSec 1.3.6.1.4.1.311.1.1.3.1.1.7.1.8
Page Faults/sec is the rate of Page Faults by the threads executing in this process. A page fault occurs when a thread refers to a virtual memory page that is not in its working set in main memory. This will not cause the page to be fetched from disk if it is on the standby list and hence already in main memory, or if it is in use by another process with whom the page is shared.
Status: mandatory Access: read-only
OBJECT-TYPE    
  Counter  

processWorkingSetPeak 1.3.6.1.4.1.311.1.1.3.1.1.7.1.9
Working Set Peak is the maximum number of bytes in the Working Set of this process at any point in time. The Working Set is the set of memory pages touched recently by the threads in the process. If free memory in the computer is above a threshold, pages are left in the Working Set of a process even if they are not in use. When free memory falls below a threshold, pages are trimmed from Working Sets. If they are needed they will then be soft-faulted back into the Working Set before they leave main memory.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER  

processWorkingSet 1.3.6.1.4.1.311.1.1.3.1.1.7.1.10
Working Set is the current number of bytes in the Working Set of this process. The Working Set is the set of memory pages touched recently by the threads in the process. If free memory in the computer is above a threshold, pages are left in the Working Set of a process even if they are not in use. When free memory falls below a threshold, pages are trimmed from Working Sets. If they are needed they will then be soft-faulted back into the Working Set before they leave main memory.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER  

processPageFileBytesPeak 1.3.6.1.4.1.311.1.1.3.1.1.7.1.11
Page File Bytes Peak is the maximum number of bytes this process has used in the paging file(s). Paging files are used to store pages of memory used by the process that are not contained in other files. Paging files are shared by all processes, and lack of space in paging files can prevent other processes from allocating memory.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER  

processPageFileBytes 1.3.6.1.4.1.311.1.1.3.1.1.7.1.12
Page File Bytes is the current number of bytes this process has used in the paging file(s). Paging files are used to store pages of memory used by the process that are not contained in other files. Paging files are shared by all processes, and lack of space in paging files can prevent other processes from allocating memory.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER  

processPrivateBytes 1.3.6.1.4.1.311.1.1.3.1.1.7.1.13
Private Bytes is the current number of bytes this process has allocated that cannot be shared with other processes.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER  

processThreadCount 1.3.6.1.4.1.311.1.1.3.1.1.7.1.14
The number of threads currently active in this process. An instruction is the basic unit of execution in a processor, and a thread is the object that executes instructions. Every running process has at least one thread.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER  

processPriorityBase 1.3.6.1.4.1.311.1.1.3.1.1.7.1.15
The current base priority of this process. Threads within a process can raise and lower their own base priority relative to the process's base priority.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER  

processElapsedTime 1.3.6.1.4.1.311.1.1.3.1.1.7.1.16
The total elapsed time (in seconds) this process has been running.
Status: mandatory Access: read-only
OBJECT-TYPE    
  TimeTicks  

processIDProcess 1.3.6.1.4.1.311.1.1.3.1.1.7.1.17
ID Process is the unique identifier of this process. ID Process numbers are reused, so they only identify a process for the lifetime of that process.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER  

processPoolPagedBytes 1.3.6.1.4.1.311.1.1.3.1.1.7.1.18
Pool Paged Bytes is the number of bytes in the Paged Pool, a system memory area where space is acquired by operating system components as they accomplish their appointed tasks. Paged Pool pages can be paged out to the paging file when not accessed by the system for sustained periods of time.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER  

processPoolNonpagedBytes 1.3.6.1.4.1.311.1.1.3.1.1.7.1.19
Pool Nonpaged Bytes is the number of bytes in the Nonpaged Pool, a system memory area where space is acquired by operating system components as they accomplish their appointed tasks. Nonpaged Pool pages cannot be paged out to the paging file, but instead remain in main memory as long as they are allocated.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER  

processHandleCount 1.3.6.1.4.1.311.1.1.3.1.1.7.1.20
The total number of handles currently open by this process. This number is the sum of the handles currently open by each thread in this process.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER  

redirector 1.3.6.1.4.1.311.1.1.3.1.1.8
OBJECT IDENTIFIER    

redirectorBytesTotalPerSec 1.3.6.1.4.1.311.1.1.3.1.1.8.1
Bytes Total/sec is the rate the Redirector is processing data bytes. This includes all application and file data in addition to protocol information such as packet headers.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER  

redirectorFileDataOperationsPerSec 1.3.6.1.4.1.311.1.1.3.1.1.8.2
File Data Operations/sec is the rate the Redirector is processing data operations. One operation includes (hopefully) many bytes. We say hopefully here because each operation has overhead. You can determine the efficiency of this path by dividing the Bytes/sec by this counter to determine the average number of bytes transferred/operation.
Status: mandatory Access: read-only
OBJECT-TYPE    
  Counter  

redirectorPacketsPerSec 1.3.6.1.4.1.311.1.1.3.1.1.8.3
Packets/sec is the rate the Redirector is processing data packets. One packet includes (hopefully) many bytes. We say hopefully here because each packet has protocol overhead. You can determine the efficiency of this path by dividing the Bytes/sec by this counter to determine the average number of bytes transferred/packet. You can also divide this counter by Operations/sec to determine the average number of packets per operation, another measure of efficiency.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER  

redirectorBytesReceivedPerSec 1.3.6.1.4.1.311.1.1.3.1.1.8.4
Bytes Received/sec is the rate of bytes coming in to the Redirector from the network. It includes all application data as well as network protocol information (such as packet headers.)
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER  

redirectorPacketsReceivedPerSec 1.3.6.1.4.1.311.1.1.3.1.1.8.5
Packets Received/sec is the rate that the Redirector is receiving packets (also called SMBs or Server Message Blocks). Network transmissions are divided into packets. The average number of bytes received in a packet can be obtained by dividing Bytes Received/sec by this counter. Some packets received may not contain incoming data, for example an acknowledgment to a write made by the Redirector would count as an incoming packet.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER  

redirectorReadBytesPagingPerSec 1.3.6.1.4.1.311.1.1.3.1.1.8.6
Read Bytes Paging/sec is the rate that the Redirector is attempting to read bytes in response to page faults. Page faults are caused by loading of modules (such as programs and libraries), by a miss in the Cache (see Read Bytes Cache/sec), or by files directly mapped into the address space of applications (a high-performance feature of Windows NT.)
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER  

redirectorReadBytesNon-PagingPerSec 1.3.6.1.4.1.311.1.1.3.1.1.8.7
Read Bytes Non-Paging/sec are those bytes read by the Redirector in response to normal file requests by an application when they are redirected to come from another computer. In addition to file requests, this counter includes other methods of reading across the network such as Named Pipes and Transactions. This counter does not count network protocol information, just application data.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER  

redirectorReadBytesCachePerSec 1.3.6.1.4.1.311.1.1.3.1.1.8.8
Read Bytes Cache/sec is the rate that applications on your computer are accessing the Cache using the Redirector. Some of these data requests may be satisfied by merely retrieving the data from the system Cache on your own computer if it happened to be used recently and there was room to keep it in the Cache. Requests that miss the Cache will cause a page fault (see Read Bytes Paging/sec).
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER  

redirectorReadBytesNetworkPerSec 1.3.6.1.4.1.311.1.1.3.1.1.8.9
Read Bytes Network/sec is the rate that applications are reading data across the network. For one reason or another the data was not in the system Cache, and these bytes actually came across the network. Dividing this number by Bytes Received/sec will indicate the 'efficiency' of data coming in from the network, since all of these bytes are real application data (see Bytes Received/sec.)
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER  

redirectorBytesTransmittedPerSec 1.3.6.1.4.1.311.1.1.3.1.1.8.10
Bytes Transmitted/sec is the rate that bytes are leaving the Redirector to the network. It includes all application data as well as network protocol information (such as packet headers and the like.)
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER  

redirectorPacketsTransmittedPerSec 1.3.6.1.4.1.311.1.1.3.1.1.8.11
Packets Transmitted/sec is the rate that the Redirector is sending packets (also called SMBs or Server Message Blocks). Network transmissions are divided into packets. The average number of bytes transmitted in a packet can be obtained by dividing Bytes Transmitted/sec by this counter.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER  

redirectorWriteBytesPagingPerSec 1.3.6.1.4.1.311.1.1.3.1.1.8.12
Write Bytes Paging/sec is the rate that the Redirector is attempting to write bytes changed in the pages being used by applications. The program data changed by modules (such as programs and libraries) that were loaded over the network are 'paged out' when no longer needed. Other output pages come from the Cache (see Write Bytes Cache/sec).
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER  

redirectorWriteBytesNon-PagingPerSec 1.3.6.1.4.1.311.1.1.3.1.1.8.13
Write Bytes Non-Paging/sec is the rate of the bytes that are written by the Redirector in response to normal file outputs by an application when they are redirected to go to another computer. In addition to file requests this counter includes other methods of writing across the network such as Named Pipes and Transactions. This counter does not count network protocol information, just application data.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER  

redirectorWriteBytesCachePerSec 1.3.6.1.4.1.311.1.1.3.1.1.8.14
Write Bytes Cache/sec is the rate that applications on your computer are writing to the Cache using the Redirector. The data may not leave your computer immediately, but may be retained in the Cache for further modification before being written to the network. This saves network traffic. Each write of a byte into the Cache is counted here.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER  

redirectorWriteBytesNetworkPerSec 1.3.6.1.4.1.311.1.1.3.1.1.8.15
Write Bytes Network/sec is the rate that your applications are writing data across the network. Either the system Cache was bypassed, as for Named Pipes or Transactions, or else the Cache wrote the bytes to make room for other data. Dividing this counter by Bytes Transmitted/sec will indicate the 'efficiency' of data written to the network, since all of these bytes are real application data (see Transmitted Bytes/sec.)
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER  

redirectorFileReadOperationsPerSec 1.3.6.1.4.1.311.1.1.3.1.1.8.16
File Read Operations/sec is the rate that applications are asking the Redirector for data. Each call to a file system or similar Application Program Interface (API) call counts as one operation.
Status: mandatory Access: read-only
OBJECT-TYPE    
  Counter  

redirectorReadOperationsRandomPerSec 1.3.6.1.4.1.311.1.1.3.1.1.8.17
Read Operations Random/sec counts the rate that, on a file-by-file basis, reads are made that are not sequential. If a read is made using a particular file handle, and then is followed by another read that is not immediately the contiguous next byte, this counter is incremented by one.
Status: mandatory Access: read-only
OBJECT-TYPE    
  Counter  

redirectorReadPacketsPerSec 1.3.6.1.4.1.311.1.1.3.1.1.8.18
Read Packets/sec is the rate that read packets are being placed on the network. Each time a single packet is sent with a request to read data remotely, this counter is incremented by one.
Status: mandatory Access: read-only
OBJECT-TYPE    
  Counter  

redirectorReadsLargePerSec 1.3.6.1.4.1.311.1.1.3.1.1.8.19
Reads Large/sec is the rate that reads over 2 times the server's negotiated buffer size are made by applications. Too many of these could place a strain on server resources. This counter is incremented once for each read. It does not count packets.
Status: mandatory Access: read-only
OBJECT-TYPE    
  Counter  

redirectorReadPacketsSmallPerSec 1.3.6.1.4.1.311.1.1.3.1.1.8.20
Read Packets Small/sec is the rate that reads less than one-fourth of the server's negotiated buffer size are made by applications. Too many of these could indicate a waste of buffers on the server. This counter is incremented once for each read. It does not count packets.
Status: mandatory Access: read-only
OBJECT-TYPE    
  Counter  

redirectorFileWriteOperationsPerSec 1.3.6.1.4.1.311.1.1.3.1.1.8.21
File Write Operations/sec is the rate that applications are sending data to the Redirector. Each call to a file system or similar Application Program Interface (API) call counts as one operation.
Status: mandatory Access: read-only
OBJECT-TYPE    
  Counter  

redirectorWriteOperationsRandomPerSec 1.3.6.1.4.1.311.1.1.3.1.1.8.22
Write Operations Random/sec is the rate that, on a file-by-file basis, writes are made that are not sequential. If a write is made using a particular file handle, and then is followed by another write that is not immediately the next contiguous byte, this counter is incremented by one.
Status: mandatory Access: read-only
OBJECT-TYPE    
  Counter  

redirectorWritePacketsPerSec 1.3.6.1.4.1.311.1.1.3.1.1.8.23
Write Packets/sec is the rate that writes are being sent to the network. Each time a single packet is sent with a request to write remote data, this counter is incremented by one.
Status: mandatory Access: read-only
OBJECT-TYPE    
  Counter  

redirectorWritesLargePerSec 1.3.6.1.4.1.311.1.1.3.1.1.8.24
Writes Large/sec is the rate that writes are made by applications that are over 2 times the server's negotiated buffer size. Too many of these could place a strain on server resources. This counter is incremented once for each write: it counts writes, not packets.
Status: mandatory Access: read-only
OBJECT-TYPE    
  Counter  

redirectorWritePacketsSmallPerSec 1.3.6.1.4.1.311.1.1.3.1.1.8.25
Write Packets Small/sec is the rate that writes are made by applications that are less than one-fourth of the server's negotiated buffer size. Too many of these could indicate a waste of buffers on the server. This counter is incremented once for each write: it counts writes, not packets!
Status: mandatory Access: read-only
OBJECT-TYPE    
  Counter  

redirectorReadsDeniedPerSec 1.3.6.1.4.1.311.1.1.3.1.1.8.26
Reads Denied/sec is the rate that the server is unable to accommodate requests for Raw Reads. When a read is much larger than the server's negotiated buffer size, the Redirector requests a Raw Read which, if granted, would permit the transfer of the data without lots of protocol overhead on each packet. To accomplish this the server must lock out other requests, so the request is denied if the server is really busy.
Status: mandatory Access: read-only
OBJECT-TYPE    
  Counter  

redirectorWritesDeniedPerSec 1.3.6.1.4.1.311.1.1.3.1.1.8.27
Writes Denied/sec is the rate that the server is unable to accommodate requests for Raw Writes. When a write is much larger than the server's negotiated buffer size, the Redirector requests a Raw Write which, if granted, would permit the transfer of the data without lots of protocol overhead on each packet. To accomplish this the server must lock out other requests, so the request is denied if the server is really busy.
Status: mandatory Access: read-only
OBJECT-TYPE    
  Counter  

redirectorNetworkErrorsPerSec 1.3.6.1.4.1.311.1.1.3.1.1.8.28
Network Errors/sec counts serious unexpected errors that generally indicate the Redirector and one or more Servers are having serious communication difficulties. For example an SMB (Server Manager Block) protocol error will generate a Network Error. These result in an entry in the system Event Log, so look there for details.
Status: mandatory Access: read-only
OBJECT-TYPE    
  Counter  

redirectorServerSessions 1.3.6.1.4.1.311.1.1.3.1.1.8.29
Server Sessions counts the total number of security objects the Redirector has managed. For example, a Logon to a server followed by a network access to the same server will establish one connection, but two sessions.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER  

redirectorServerReconnects 1.3.6.1.4.1.311.1.1.3.1.1.8.30
Server Reconnects counts the number of times your Redirector has had to reconnect to a server in order to complete a new active request. You can be disconnected by the Server if you remain inactive for too long. Locally even if all your remote files are closed, the Redirector will keep your connections intact for (nominally) ten minutes. Such inactive connections are called Dormant Connections. Reconnecting is expensive in time.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER  

redirectorConnectsCore 1.3.6.1.4.1.311.1.1.3.1.1.8.31
Connects Core counts the number of connections you have to servers running the original MS-Net SMB protocol, including MS-Net itself and Xenix and Vax's.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER  

redirectorConnectsLanManager20 1.3.6.1.4.1.311.1.1.3.1.1.8.32
Connects Lan Manager 2.0 counts connections to Lan Manager 2.0 servers, including LMX servers.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER  

redirectorConnectsLanManager21 1.3.6.1.4.1.311.1.1.3.1.1.8.33
Connects Lan Manager 2.1 counts connections to Lan Manager 2.1 servers, including LMX servers.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER  

redirectorConnectsWindowsNT 1.3.6.1.4.1.311.1.1.3.1.1.8.34
Connects Windows NT counts the connections to Windows NT computers. Good choice!
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER  

redirectorServerDisconnects 1.3.6.1.4.1.311.1.1.3.1.1.8.35
Server Disconnects counts the number of times a Server has disconnected your Redirector. See also Server Reconnects.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER  

redirectorServerSessionsHung 1.3.6.1.4.1.311.1.1.3.1.1.8.36
Server Sessions Hung counts the number of active sessions that are timed out and unable to proceed due to a lack of response from the remote server.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER  

redirectorCurrentCommands 1.3.6.1.4.1.311.1.1.3.1.1.8.37
Current Commands counts the number of requests to the Redirector that are currently queued for service. If this number is much larger than the number of network adapter cards installed in the computer, then the network(s) and/or the server(s) being accessed are seriously bottlenecked.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER  

tCP 1.3.6.1.4.1.311.1.1.3.1.1.9
OBJECT IDENTIFIER    

tcpSegmentsPerSec 1.3.6.1.4.1.311.1.1.3.1.1.9.1
Segments/sec is the rate that TCP segments are sent or received using the TCP protocol.
Status: mandatory Access: read-only
OBJECT-TYPE    
  Counter  

tcpConnectionsEstablished 1.3.6.1.4.1.311.1.1.3.1.1.9.2
Connections Established is the number of TCP connections for which the current state is either ESTABLISHED or CLOSE-WAIT.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER  

tcpConnectionsActive 1.3.6.1.4.1.311.1.1.3.1.1.9.3
Connections Active is the number of times TCP connections have made a direct transition to the SYN-SENT state from the CLOSED state.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER  

tcpConnectionsPassive 1.3.6.1.4.1.311.1.1.3.1.1.9.4
Connections Passive is the number of times TCP connections have made a direct transition to the SYN-RCVD state from the LISTEN state.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER  

tcpConnectionFailures 1.3.6.1.4.1.311.1.1.3.1.1.9.5
Connection Failures is the number of times TCP connections have made a direct transition to the CLOSED state from the SYN-SENT state or the SYN-RCVD state, plus the number of times TCP connections have made a direct transition to the LISTEN state from the SYN-RCVD state.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER  

tcpConnectionsReset 1.3.6.1.4.1.311.1.1.3.1.1.9.6
Connections Reset is the number of times TCP connections have made a direct transition to the CLOSED state from either the ESTABLISHED state or the CLOSE-WAIT state.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER  

tcpSegmentsReceivedPerSec 1.3.6.1.4.1.311.1.1.3.1.1.9.7
Segments Received/sec is the rate that segments are received, including those received in error. This count includes segments received on currently established connections.
Status: mandatory Access: read-only
OBJECT-TYPE    
  Counter  

tcpSegmentsSentPerSec 1.3.6.1.4.1.311.1.1.3.1.1.9.8
Segments Sent/sec is the rate that segments are sent, including those on current connections, but excluding those containing only retransmitted bytes.
Status: mandatory Access: read-only
OBJECT-TYPE    
  Counter  

tcpSegmentsRetransmittedPerSec 1.3.6.1.4.1.311.1.1.3.1.1.9.9
Segments Retransmitted/sec is the rate that segments are retransmitted, that is, segments transmitted containing one or more previously transmitted bytes.
Status: mandatory Access: read-only
OBJECT-TYPE    
  Counter  

iP 1.3.6.1.4.1.311.1.1.3.1.1.10
OBJECT IDENTIFIER    

ipDatagramsPerSec 1.3.6.1.4.1.311.1.1.3.1.1.10.1
Datagrams/sec is the rate that IP datagrams are received from or sent to the interfaces, including those in error. Any forwarded datagrams are not included in this rate.
Status: mandatory Access: read-only
OBJECT-TYPE    
  Counter  

ipDatagramsReceivedPerSec 1.3.6.1.4.1.311.1.1.3.1.1.10.2
Datagrams Received/sec is the rate that IP datagrams are received from the interfaces, including those in error.
Status: mandatory Access: read-only
OBJECT-TYPE    
  Counter  

ipDatagramsReceivedHeaderErrors 1.3.6.1.4.1.311.1.1.3.1.1.10.3
Datagrams Received Header Errors is the number of input datagrams discarded due to errors in their IP headers, including bad checksums, version number mismatch, other format errors, time-to-live exceeded, errors discovered in processing their IP options, etc.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER  

ipDatagramsReceivedAddressErrors 1.3.6.1.4.1.311.1.1.3.1.1.10.4
Datagrams Received Address Errors is the number of input datagrams discarded because the IP address in their IP header's destination field was not a valid address to be received at this entity. This count includes invalid addresses (e.g., 0.0. 0.0) and addresses of unsupported Classes (e.g., Class E). For entities that are not IP Gateways and therefore do not forward datagrams, this counter includes datagrams discarded because the destination address was not a local address.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER  

ipDatagramsForwardedPerSec 1.3.6.1.4.1.311.1.1.3.1.1.10.5
Datagrams Forwarded/sec is the rate of input datagrams for that this entity was not their final IP destination, as a result of which an attempt was made to find a route to forward them to that final destination. In entities that do not act as IP Gateways, this rate will include only those packets that were Source-Routed via this entity, and the Source-Route option processing was successful.
Status: mandatory Access: read-only
OBJECT-TYPE    
  Counter  

ipDatagramsReceivedUnknownProtocol 1.3.6.1.4.1.311.1.1.3.1.1.10.6
Datagrams Received Unknown Protocol is the number of locally-addressed datagrams received successfully but discarded because of an unknown or unsupported protocol.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER  

ipDatagramsReceivedDiscarded 1.3.6.1.4.1.311.1.1.3.1.1.10.7
Datagrams Received Discarded is the number of input IP datagrams for which no problems were encountered to prevent their continued processing, but which were discarded (e.g., for lack of buffer space). This counter does not include any datagrams discarded while awaiting re-assembly.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER  

ipDatagramsReceivedDeliveredPerSec 1.3.6.1.4.1.311.1.1.3.1.1.10.8
Datagrams Received Delivered/sec is the rate that input datagrams are successfully delivered to IP user-protocols (including ICMP).
Status: mandatory Access: read-only
OBJECT-TYPE    
  Counter  

ipDatagramsSentPerSec 1.3.6.1.4.1.311.1.1.3.1.1.10.9
Datagrams Sent/sec is the rate that IP datagrams are supplied to IP for transmission by local IP user-protocols (including ICMP). That this counter does not include any datagrams counted in Datagrams Forwarded.
Status: mandatory Access: read-only
OBJECT-TYPE    
  Counter  

ipDatagramsOutboundDiscarded 1.3.6.1.4.1.311.1.1.3.1.1.10.10
Datagrams Outbound Discarded is the number of output IP datagrams for which no problems were encountered to prevent their transmission to their destination, but which were discarded (e.g., for lack of buffer space.) This counter would include datagrams counted in Datagrams Forwarded if any such packets met this (discretionary) discard criterion.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER  

ipDatagramsOutboundNoRoute 1.3.6.1.4.1.311.1.1.3.1.1.10.11
Datagrams Outbound No Route is the number of IP datagrams discarded because no route could be found to transmit them to their destination. This counter includes any packets counted in Datagrams Forwarded that meet this `no route' criterion.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER  

ipFragmentsReceivedPerSec 1.3.6.1.4.1.311.1.1.3.1.1.10.12
Fragments Received/sec is the rate that IP fragments that need to be re-assembled at this entity are received.
Status: mandatory Access: read-only
OBJECT-TYPE    
  Counter  

ipFragmentsRe-assembledPerSec 1.3.6.1.4.1.311.1.1.3.1.1.10.13
Fragments Re-assembled/sec is the rate that IP fragments are successfully re-assembled.
Status: mandatory Access: read-only
OBJECT-TYPE    
  Counter  

ipFragmentRe-assemblyFailures 1.3.6.1.4.1.311.1.1.3.1.1.10.14
Fragment Re-assembly Failures is the number of failures detected by the IP re-assembly algorithm (for whatever reason: timed out, errors, etc.) This is not necessarily a count of discarded IP fragments since some algorithms (notably RFC 815) can lose track of the number of fragments by combining them as they are received.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER  

ipFragmentedDatagramsPerSec 1.3.6.1.4.1.311.1.1.3.1.1.10.15
Fragmented Datagrams/sec is the rate that datagrams are successfully fragmented at this entity.
Status: mandatory Access: read-only
OBJECT-TYPE    
  Counter  

ipFragmentationFailures 1.3.6.1.4.1.311.1.1.3.1.1.10.16
Fragmentation Failures is the number of IP datagrams that have been discarded because they needed to be fragmented at this entity but could not be, e.g., because their `Don't Fragment' flag was set.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER  

ipFragmentsCreatedPerSec 1.3.6.1.4.1.311.1.1.3.1.1.10.17
Fragments Created/sec is the rate that IP datagram fragments have been generated as a result of fragmentation at this entity.
Status: mandatory Access: read-only
OBJECT-TYPE    
  Counter  

uDP 1.3.6.1.4.1.311.1.1.3.1.1.11
OBJECT IDENTIFIER    

udpDatagramsPerSec 1.3.6.1.4.1.311.1.1.3.1.1.11.1
Datagrams/sec is the rate that UDP datagrams are sent or received by the entity.
Status: mandatory Access: read-only
OBJECT-TYPE    
  Counter  

udpDatagramsReceivedPerSec 1.3.6.1.4.1.311.1.1.3.1.1.11.2
Datagrams Received/sec is the rate that UDP datagrams are delivered to UDP users.
Status: mandatory Access: read-only
OBJECT-TYPE    
  Counter  

udpDatagramsNoPortPerSec 1.3.6.1.4.1.311.1.1.3.1.1.11.3
Datagrams No Port/sec is the rate of received UDP datagrams for which there was no application at the destination port.
Status: mandatory Access: read-only
OBJECT-TYPE    
  Counter  

udpDatagramsReceivedErrors 1.3.6.1.4.1.311.1.1.3.1.1.11.4
Datagrams Received Errors is the number of received UDP datagrams that could not be delivered for reasons other than the lack of an application at the destination port.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER  

udpDatagramsSentPerSec 1.3.6.1.4.1.311.1.1.3.1.1.11.5
Datagrams Sent/sec is the rate that UDP datagrams are sent from the entity.
Status: mandatory Access: read-only
OBJECT-TYPE    
  Counter  

netbeuinetBEUITable 1.3.6.1.4.1.311.1.1.3.1.1.12
A table containing performance information for instances of 'netBEUI' objects.
Status: mandatory Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    NetbeuinetBEUIEntry

netbeuinetBEUIEntry 1.3.6.1.4.1.311.1.1.3.1.1.12.1
Performance information for one particular instance of 'netBEUI' object.
Status: mandatory Access: not-accessible
OBJECT-TYPE    
  NetbeuinetBEUIEntry  

netbeuinetBEUIIndex 1.3.6.1.4.1.311.1.1.3.1.1.12.1.1
Index.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER  

netbeuinetBEUIInstance 1.3.6.1.4.1.311.1.1.3.1.1.12.1.2
Instance name.
Status: mandatory Access: read-only
OBJECT-TYPE    
  DisplayString  

netbeuiDatagramsPerSec 1.3.6.1.4.1.311.1.1.3.1.1.12.1.3
Datagrams/sec is the rate that datagrams are processed by the computer. This counter displays the sum of datagrams sent and datagrams received. A datagram is a connectionless packet whose delivery to a remote is not guaranteed.
Status: mandatory Access: read-only
OBJECT-TYPE    
  Counter  

netbeuiDatagramBytesPerSec 1.3.6.1.4.1.311.1.1.3.1.1.12.1.4
Datagram Bytes/sec is the rate that datagram bytes are processed by the computer. This counter is the sum of datagram bytes that are sent as well as received. A datagram is a connectionless packet whose delivery to a remote is not guaranteed.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER  

netbeuiPacketsPerSec 1.3.6.1.4.1.311.1.1.3.1.1.12.1.5
Packets/sec is the rate that packets are processed by the computer. This count is the sum of Packets Sent and Packets Received per second. This counter includes all packets processed: control as well as data packets.
Status: mandatory Access: read-only
OBJECT-TYPE    
  Counter  

netbeuiFramesPerSec 1.3.6.1.4.1.311.1.1.3.1.1.12.1.6
Frames/sec is the rate that data frames (or packets) are processed by the computer. This counter is the sum of data frames sent and data frames received. This counter only counts those frames (packets) that carry data.
Status: mandatory Access: read-only
OBJECT-TYPE    
  Counter  

netbeuiFrameBytesPerSec 1.3.6.1.4.1.311.1.1.3.1.1.12.1.7
Frame Bytes/sec is the rate that data bytes are processed by the computer. This counter is the sum of data frame bytes sent and received. This counter only counts the byte in frames (packets) that carry data.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER  

netbeuiBytesTotalPerSec 1.3.6.1.4.1.311.1.1.3.1.1.12.1.8
Bytes Total/sec is the sum of Frame Bytes/sec and Datagram Bytes/sec. This is the total rate of bytes sent to or received from the network by the protocol, but only counts the bytes in frames (i.e., packets) which carry data.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER  

netbeuiConnectionsOpen 1.3.6.1.4.1.311.1.1.3.1.1.12.1.9
Connections Open is the number of connections currently open for this protocol. This counter shows the current count only and does not accumulate over time.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER  

netbeuiConnectionsNoRetries 1.3.6.1.4.1.311.1.1.3.1.1.12.1.10
Connections No Retries is the total count of connections that were successfully made on the first try. This number is an accumulator and shows a running total.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER  

netbeuiConnectionsWithRetries 1.3.6.1.4.1.311.1.1.3.1.1.12.1.11
Connections With Retries is the total count of connections that were made after retrying the attempt. A retry occurs when the first connection attempt failed. This number is an accumulator and shows a running total.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER  

netbeuiDisconnectsLocal 1.3.6.1.4.1.311.1.1.3.1.1.12.1.12
Disconnects Local is the number of session disconnections that were initiated by the local computer. This number is an accumulator and shows a running total.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER  

netbeuiDisconnectsRemote 1.3.6.1.4.1.311.1.1.3.1.1.12.1.13
Disconnects Remote is the number of session disconnections that were initiated by the remote computer. This number is an accumulator and shows a running total.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER  


netbeuiFailuresAdapter 1.3.6.1.4.1.311.1.1.3.1.1.12.1.15
Failures Adapter is the number of connections that were dropped due to an adapter failure. This number is an accumulator and shows a running total.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER  

netbeuiConnectionSessionTimeouts 1.3.6.1.4.1.311.1.1.3.1.1.12.1.16
Connection Session Timeouts is the number of connections that were dropped due to a session timeout. This number is an accumulator and shows a running total.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER  

netbeuiConnectionsCanceled 1.3.6.1.4.1.311.1.1.3.1.1.12.1.17
Connections Canceled is the number of connections that were canceled. This number is an accumulator and shows a running total.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER  

netbeuiFailuresResourceRemote 1.3.6.1.4.1.311.1.1.3.1.1.12.1.18
Failures Resource Remote is the number of connections that failed because of resource problems or shortages on the remote computer. This number is an accumulator and shows a running total.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER  

netbeuiFailuresResourceLocal 1.3.6.1.4.1.311.1.1.3.1.1.12.1.19
Failures Resource Local is the number of connections that failed because of resource problems or shortages on the local computer. This number is an accumulator and shows a running total.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER  

netbeuiFailuresNotFound 1.3.6.1.4.1.311.1.1.3.1.1.12.1.20
Failures Not Found is the number of connection attempts that failed because the remote computer could not be found. This number is an accumulator and shows a running total.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER  

netbeuiFailuresNoListen 1.3.6.1.4.1.311.1.1.3.1.1.12.1.21
Failures No Listen is the number of connections that were rejected because the remote computer was not listening for connection requests.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER  

netbeuiDatagramsSentPerSec 1.3.6.1.4.1.311.1.1.3.1.1.12.1.22
Datagrams Sent/sec is the rate that datagrams are sent from the computer. A datagram is a connectionless packet whose delivery to a remote computer is not guaranteed.
Status: mandatory Access: read-only
OBJECT-TYPE    
  Counter  

netbeuiDatagramBytesSentPerSec 1.3.6.1.4.1.311.1.1.3.1.1.12.1.23
Datagram Bytes Sent/sec is the rate that datagram bytes are sent from the computer. A datagram is a connectionless packet whose delivery to a remote computer is not guaranteed.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER  

netbeuiDatagramsReceivedPerSec 1.3.6.1.4.1.311.1.1.3.1.1.12.1.24
Datagrams Received/sec is the rate that datagrams are received by the computer. A datagram is a connectionless packet whose delivery to a remote computer is not guaranteed.
Status: mandatory Access: read-only
OBJECT-TYPE    
  Counter  

netbeuiDatagramBytesReceivedPerSec 1.3.6.1.4.1.311.1.1.3.1.1.12.1.25
Datagram Bytes Received/sec is the rate that datagram bytes are received by the computer. A datagram is a connectionless packet whose delivery to a remote computer is not guaranteed.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER  

netbeuiPacketsSentPerSec 1.3.6.1.4.1.311.1.1.3.1.1.12.1.26
Packets Sent/sec is the rate that packets are sent by the computer. This counter counts all packets sent by the computer, i.e. control as well as data packets.
Status: mandatory Access: read-only
OBJECT-TYPE    
  Counter  

netbeuiPacketsReceivedPerSec 1.3.6.1.4.1.311.1.1.3.1.1.12.1.27
Packets Received/sec is the rate that packets are received by the computer. This counter counts all packets processed: control as well as data packets.
Status: mandatory Access: read-only
OBJECT-TYPE    
  Counter  

netbeuiFramesSentPerSec 1.3.6.1.4.1.311.1.1.3.1.1.12.1.28
Frames Sent/sec is the rate that data frames are sent by the computer. This counter only counts the frames (packets) that carry data.
Status: mandatory Access: read-only
OBJECT-TYPE    
  Counter  

netbeuiFrameBytesSentPerSec 1.3.6.1.4.1.311.1.1.3.1.1.12.1.29
Frame Bytes Sent/sec is the rate that data bytes are sent by the computer. This counter only counts the bytes in frames (packets) that carry data.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER  

netbeuiFramesReceivedPerSec 1.3.6.1.4.1.311.1.1.3.1.1.12.1.30
Frames Received/sec is the rate that data frames are received by the computer. This counter only counts the frames (packets) that carry data.
Status: mandatory Access: read-only
OBJECT-TYPE    
  Counter  

netbeuiFrameBytesReceivedPerSec 1.3.6.1.4.1.311.1.1.3.1.1.12.1.31
Frame Bytes Received/sec is the rate that data bytes are received by the computer. This counter only counts the frames (packets) that carry data.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER  

netbeuiFramesRe-SentPerSec 1.3.6.1.4.1.311.1.1.3.1.1.12.1.32
Frames Re-Sent/sec is the rate that data frames (packets) are re-sent by the computer. This counter only counts the frames or packets that carry data.
Status: mandatory Access: read-only
OBJECT-TYPE    
  Counter  

netbeuiFrameBytesRe-SentPerSec 1.3.6.1.4.1.311.1.1.3.1.1.12.1.33
Frame Bytes Re-Sent/sec is the rate that data bytes are re-sent by the computer. This counter only counts the bytes in frames that carry data.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER  

netbeuiFramesRejectedPerSec 1.3.6.1.4.1.311.1.1.3.1.1.12.1.34
Frames Rejected/sec is the rate that data frames are rejected. This counter only counts the frames (packets) that carry data.
Status: mandatory Access: read-only
OBJECT-TYPE    
  Counter  

netbeuiFrameBytesRejectedPerSec 1.3.6.1.4.1.311.1.1.3.1.1.12.1.35
Frame Bytes Rejected/sec is the rate that data bytes are rejected. This counter only counts the bytes in data frames (packets) that carry data.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER  

netbeuiExpirationsResponse 1.3.6.1.4.1.311.1.1.3.1.1.12.1.36
Expirations Response is the count of T1 timer expirations.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER  

netbeuiExpirationsAck 1.3.6.1.4.1.311.1.1.3.1.1.12.1.37
Expirations Ack is the count of T2 timer expirations
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER  

netbeuiWindowSendMaximum 1.3.6.1.4.1.311.1.1.3.1.1.12.1.38
Window Send Maximum is the maximum number of bytes of data that will be sent before waiting for an acknowledgment from the remote computer.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER  

netbeuiWindowSendAverage 1.3.6.1.4.1.311.1.1.3.1.1.12.1.39
Window Send Average is the running average number of data bytes that were sent before waiting for an acknowledgment from the remote computer.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER  

netbeuiPiggybackAckQueuedPerSec 1.3.6.1.4.1.311.1.1.3.1.1.12.1.40
Piggyback Ack Queued/sec is the rate that piggybacked acknowledgments are queued. Piggyback acknowledgments are acknowledgments to received packets that are to be included in the next outgoing packet to the remote computer.
Status: mandatory Access: read-only
OBJECT-TYPE    
  Counter  

netbeuiPiggybackAckTimeouts 1.3.6.1.4.1.311.1.1.3.1.1.12.1.41
Piggyback Ack Timeouts is the number of times that a piggyback acknowledgment could not be sent because there was no outgoing packet to the remote on which to piggyback. A piggyback ack is an acknowledgment to a received packet that is sent along in an outgoing data packet to the remote computer. If no outgoing packet is sent within the timeout period, then an ack packet is sent and this counter is incremented.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER  

nbtconnnBT-ConnectionTable 1.3.6.1.4.1.311.1.1.3.1.1.13
A table containing performance information for instances of 'nBT-Connection' objects.
Status: mandatory Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    NbtconnnBT-ConnectionEntry

nbtconnnBT-ConnectionEntry 1.3.6.1.4.1.311.1.1.3.1.1.13.1
Performance information for one particular instance of 'nBT-Connection' object.
Status: mandatory Access: not-accessible
OBJECT-TYPE    
  NbtconnnBT-ConnectionEntry  

nbtconnnBT-ConnectionIndex 1.3.6.1.4.1.311.1.1.3.1.1.13.1.1
Index.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER  

nbtconnnBT-ConnectionInstance 1.3.6.1.4.1.311.1.1.3.1.1.13.1.2
Instance name.
Status: mandatory Access: read-only
OBJECT-TYPE    
  DisplayString  

nbtconnBytesReceivedPerSec 1.3.6.1.4.1.311.1.1.3.1.1.13.1.3
Bytes Received/sec is the rate that bytes are received by the local computer over an NBT connection to some remote computer. All the bytes received by the local computer over the particular NBT connection are counted.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER  

nbtconnBytesSentPerSec 1.3.6.1.4.1.311.1.1.3.1.1.13.1.4
Bytes Sent/sec is the rate that bytes are sent by the local computer over an NBT connection to some remote computer. All the bytes sent by the local computer over the particular NBT connection are counted.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER  

nbtconnBytesTotalPerSec 1.3.6.1.4.1.311.1.1.3.1.1.13.1.5
Total Bytes/sec is the rate that bytes are sent or received by the local computer over an NBT connection to some remote computer. All the bytes sent or received by the local computer over the particular NBT connection are counted.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER  





nwlinkipxDatagramsPerSec 1.3.6.1.4.1.311.1.1.3.1.1.14.1.3
Datagrams/sec is the rate that datagrams are processed by the computer. This counter displays the sum of datagrams sent and datagrams received. A datagram is a connectionless packet whose delivery to a remote is not guaranteed.
Status: mandatory Access: read-only
OBJECT-TYPE    
  Counter  

nwlinkipxDatagramBytesPerSec 1.3.6.1.4.1.311.1.1.3.1.1.14.1.4
Datagram Bytes/sec is the rate that datagram bytes are processed by the computer. This counter is the sum of datagram bytes that are sent as well as received. A datagram is a connectionless packet whose delivery to a remote is not guaranteed.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER  

nwlinkipxPacketsPerSec 1.3.6.1.4.1.311.1.1.3.1.1.14.1.5
Packets/sec is the rate that packets are processed by the computer. This count is the sum of Packets Sent and Packets Received per second. This counter includes all packets processed: control as well as data packets.
Status: mandatory Access: read-only
OBJECT-TYPE    
  Counter  

nwlinkipxFramesPerSec 1.3.6.1.4.1.311.1.1.3.1.1.14.1.6
Frames/sec is the rate that data frames (or packets) are processed by the computer. This counter is the sum of data frames sent and data frames received. This counter only counts those frames (packets) that carry data.
Status: mandatory Access: read-only
OBJECT-TYPE    
  Counter  

nwlinkipxFrameBytesPerSec 1.3.6.1.4.1.311.1.1.3.1.1.14.1.7
Frame Bytes/sec is the rate that data bytes are processed by the computer. This counter is the sum of data frame bytes sent and received. This counter only counts the byte in frames (packets) that carry data.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER  

nwlinkipxBytesTotalPerSec 1.3.6.1.4.1.311.1.1.3.1.1.14.1.8
Bytes Total/sec is the sum of Frame Bytes/sec and Datagram Bytes/sec. This is the total rate of bytes sent to or received from the network by the protocol, but only counts the bytes in frames (i.e., packets) which carry data.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER  

nwlinkipxConnectionsOpen 1.3.6.1.4.1.311.1.1.3.1.1.14.1.9
Connections Open is the number of connections currently open for this protocol. This counter shows the current count only and does not accumulate over time.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER  

nwlinkipxConnectionsNoRetries 1.3.6.1.4.1.311.1.1.3.1.1.14.1.10
Connections No Retries is the total count of connections that were successfully made on the first try. This number is an accumulator and shows a running total.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER  

nwlinkipxConnectionsWithRetries 1.3.6.1.4.1.311.1.1.3.1.1.14.1.11
Connections With Retries is the total count of connections that were made after retrying the attempt. A retry occurs when the first connection attempt failed. This number is an accumulator and shows a running total.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER  

nwlinkipxDisconnectsLocal 1.3.6.1.4.1.311.1.1.3.1.1.14.1.12
Disconnects Local is the number of session disconnections that were initiated by the local computer. This number is an accumulator and shows a running total.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER  

nwlinkipxDisconnectsRemote 1.3.6.1.4.1.311.1.1.3.1.1.14.1.13
Disconnects Remote is the number of session disconnections that were initiated by the remote computer. This number is an accumulator and shows a running total.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER  


nwlinkipxFailuresAdapter 1.3.6.1.4.1.311.1.1.3.1.1.14.1.15
Failures Adapter is the number of connections that were dropped due to an adapter failure. This number is an accumulator and shows a running total.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER  

nwlinkipxConnectionSessionTimeouts 1.3.6.1.4.1.311.1.1.3.1.1.14.1.16
Connection Session Timeouts is the number of connections that were dropped due to a session timeout. This number is an accumulator and shows a running total.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER  

nwlinkipxConnectionsCanceled 1.3.6.1.4.1.311.1.1.3.1.1.14.1.17
Connections Canceled is the number of connections that were canceled. This number is an accumulator and shows a running total.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER  

nwlinkipxFailuresResourceRemote 1.3.6.1.4.1.311.1.1.3.1.1.14.1.18
Failures Resource Remote is the number of connections that failed because of resource problems or shortages on the remote computer. This number is an accumulator and shows a running total.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER  

nwlinkipxFailuresResourceLocal 1.3.6.1.4.1.311.1.1.3.1.1.14.1.19
Failures Resource Local is the number of connections that failed because of resource problems or shortages on the local computer. This number is an accumulator and shows a running total.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER  

nwlinkipxFailuresNotFound 1.3.6.1.4.1.311.1.1.3.1.1.14.1.20
Failures Not Found is the number of connection attempts that failed because the remote computer could not be found. This number is an accumulator and shows a running total.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER  

nwlinkipxFailuresNoListen 1.3.6.1.4.1.311.1.1.3.1.1.14.1.21
Failures No Listen is the number of connections that were rejected because the remote computer was not listening for connection requests.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER  

nwlinkipxDatagramsSentPerSec 1.3.6.1.4.1.311.1.1.3.1.1.14.1.22
Datagrams Sent/sec is the rate that datagrams are sent from the computer. A datagram is a connectionless packet whose delivery to a remote computer is not guaranteed.
Status: mandatory Access: read-only
OBJECT-TYPE    
  Counter  

nwlinkipxDatagramBytesSentPerSec 1.3.6.1.4.1.311.1.1.3.1.1.14.1.23
Datagram Bytes Sent/sec is the rate that datagram bytes are sent from the computer. A datagram is a connectionless packet whose delivery to a remote computer is not guaranteed.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER  

nwlinkipxDatagramsReceivedPerSec 1.3.6.1.4.1.311.1.1.3.1.1.14.1.24
Datagrams Received/sec is the rate that datagrams are received by the computer. A datagram is a connectionless packet whose delivery to a remote computer is not guaranteed.
Status: mandatory Access: read-only
OBJECT-TYPE    
  Counter  

nwlinkipxDatagramBytesReceivedPerSec 1.3.6.1.4.1.311.1.1.3.1.1.14.1.25
Datagram Bytes Received/sec is the rate that datagram bytes are received by the computer. A datagram is a connectionless packet whose delivery to a remote computer is not guaranteed.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER  

nwlinkipxPacketsSentPerSec 1.3.6.1.4.1.311.1.1.3.1.1.14.1.26
Packets Sent/sec is the rate that packets are sent by the computer. This counter counts all packets sent by the computer, i.e. control as well as data packets.
Status: mandatory Access: read-only
OBJECT-TYPE    
  Counter  

nwlinkipxPacketsReceivedPerSec 1.3.6.1.4.1.311.1.1.3.1.1.14.1.27
Packets Received/sec is the rate that packets are received by the computer. This counter counts all packets processed: control as well as data packets.
Status: mandatory Access: read-only
OBJECT-TYPE    
  Counter  

nwlinkipxFramesSentPerSec 1.3.6.1.4.1.311.1.1.3.1.1.14.1.28
Frames Sent/sec is the rate that data frames are sent by the computer. This counter only counts the frames (packets) that carry data.
Status: mandatory Access: read-only
OBJECT-TYPE    
  Counter  

nwlinkipxFrameBytesSentPerSec 1.3.6.1.4.1.311.1.1.3.1.1.14.1.29
Frame Bytes Sent/sec is the rate that data bytes are sent by the computer. This counter only counts the bytes in frames (packets) that carry data.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER  

nwlinkipxFramesReceivedPerSec 1.3.6.1.4.1.311.1.1.3.1.1.14.1.30
Frames Received/sec is the rate that data frames are received by the computer. This counter only counts the frames (packets) that carry data.
Status: mandatory Access: read-only
OBJECT-TYPE    
  Counter  

nwlinkipxFrameBytesReceivedPerSec 1.3.6.1.4.1.311.1.1.3.1.1.14.1.31
Frame Bytes Received/sec is the rate that data bytes are received by the computer. This counter only counts the frames (packets) that carry data.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER  

nwlinkipxFramesRe-SentPerSec 1.3.6.1.4.1.311.1.1.3.1.1.14.1.32
Frames Re-Sent/sec is the rate that data frames (packets) are re-sent by the computer. This counter only counts the frames or packets that carry data.
Status: mandatory Access: read-only
OBJECT-TYPE    
  Counter  

nwlinkipxFrameBytesRe-SentPerSec 1.3.6.1.4.1.311.1.1.3.1.1.14.1.33
Frame Bytes Re-Sent/sec is the rate that data bytes are re-sent by the computer. This counter only counts the bytes in frames that carry data.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER  

nwlinkipxFramesRejectedPerSec 1.3.6.1.4.1.311.1.1.3.1.1.14.1.34
Frames Rejected/sec is the rate that data frames are rejected. This counter only counts the frames (packets) that carry data.
Status: mandatory Access: read-only
OBJECT-TYPE    
  Counter  

nwlinkipxFrameBytesRejectedPerSec 1.3.6.1.4.1.311.1.1.3.1.1.14.1.35
Frame Bytes Rejected/sec is the rate that data bytes are rejected. This counter only counts the bytes in data frames (packets) that carry data.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER  

nwlinkipxExpirationsResponse 1.3.6.1.4.1.311.1.1.3.1.1.14.1.36
Expirations Response is the count of T1 timer expirations.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER  

nwlinkipxExpirationsAck 1.3.6.1.4.1.311.1.1.3.1.1.14.1.37
Expirations Ack is the count of T2 timer expirations
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER  

nwlinkipxWindowSendMaximum 1.3.6.1.4.1.311.1.1.3.1.1.14.1.38
Window Send Maximum is the maximum number of bytes of data that will be sent before waiting for an acknowledgment from the remote computer.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER  

nwlinkipxWindowSendAverage 1.3.6.1.4.1.311.1.1.3.1.1.14.1.39
Window Send Average is the running average number of data bytes that were sent before waiting for an acknowledgment from the remote computer.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER  

nwlinkipxPiggybackAckQueuedPerSec 1.3.6.1.4.1.311.1.1.3.1.1.14.1.40
Piggyback Ack Queued/sec is the rate that piggybacked acknowledgments are queued. Piggyback acknowledgments are acknowledgments to received packets that are to be included in the next outgoing packet to the remote computer.
Status: mandatory Access: read-only
OBJECT-TYPE    
  Counter  

nwlinkipxPiggybackAckTimeouts 1.3.6.1.4.1.311.1.1.3.1.1.14.1.41
Piggyback Ack Timeouts is the number of times that a piggyback acknowledgment could not be sent because there was no outgoing packet to the remote on which to piggyback. A piggyback ack is an acknowledgment to a received packet that is sent along in an outgoing data packet to the remote computer. If no outgoing packet is sent within the timeout period, then an ack packet is sent and this counter is incremented.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER  





nwlinkspxDatagramsPerSec 1.3.6.1.4.1.311.1.1.3.1.1.15.1.3
Datagrams/sec is the rate that datagrams are processed by the computer. This counter displays the sum of datagrams sent and datagrams received. A datagram is a connectionless packet whose delivery to a remote is not guaranteed.
Status: mandatory Access: read-only
OBJECT-TYPE    
  Counter  

nwlinkspxDatagramBytesPerSec 1.3.6.1.4.1.311.1.1.3.1.1.15.1.4
Datagram Bytes/sec is the rate that datagram bytes are processed by the computer. This counter is the sum of datagram bytes that are sent as well as received. A datagram is a connectionless packet whose delivery to a remote is not guaranteed.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER  

nwlinkspxPacketsPerSec 1.3.6.1.4.1.311.1.1.3.1.1.15.1.5
Packets/sec is the rate that packets are processed by the computer. This count is the sum of Packets Sent and Packets Received per second. This counter includes all packets processed: control as well as data packets.
Status: mandatory Access: read-only
OBJECT-TYPE    
  Counter  

nwlinkspxFramesPerSec 1.3.6.1.4.1.311.1.1.3.1.1.15.1.6
Frames/sec is the rate that data frames (or packets) are processed by the computer. This counter is the sum of data frames sent and data frames received. This counter only counts those frames (packets) that carry data.
Status: mandatory Access: read-only
OBJECT-TYPE    
  Counter  

nwlinkspxFrameBytesPerSec 1.3.6.1.4.1.311.1.1.3.1.1.15.1.7
Frame Bytes/sec is the rate that data bytes are processed by the computer. This counter is the sum of data frame bytes sent and received. This counter only counts the byte in frames (packets) that carry data.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER  

nwlinkspxBytesTotalPerSec 1.3.6.1.4.1.311.1.1.3.1.1.15.1.8
Bytes Total/sec is the sum of Frame Bytes/sec and Datagram Bytes/sec. This is the total rate of bytes sent to or received from the network by the protocol, but only counts the bytes in frames (i.e., packets) which carry data.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER  

nwlinkspxConnectionsOpen 1.3.6.1.4.1.311.1.1.3.1.1.15.1.9
Connections Open is the number of connections currently open for this protocol. This counter shows the current count only and does not accumulate over time.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER  

nwlinkspxConnectionsNoRetries 1.3.6.1.4.1.311.1.1.3.1.1.15.1.10
Connections No Retries is the total count of connections that were successfully made on the first try. This number is an accumulator and shows a running total.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER  

nwlinkspxConnectionsWithRetries 1.3.6.1.4.1.311.1.1.3.1.1.15.1.11
Connections With Retries is the total count of connections that were made after retrying the attempt. A retry occurs when the first connection attempt failed. This number is an accumulator and shows a running total.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER  

nwlinkspxDisconnectsLocal 1.3.6.1.4.1.311.1.1.3.1.1.15.1.12
Disconnects Local is the number of session disconnections that were initiated by the local computer. This number is an accumulator and shows a running total.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER  

nwlinkspxDisconnectsRemote 1.3.6.1.4.1.311.1.1.3.1.1.15.1.13
Disconnects Remote is the number of session disconnections that were initiated by the remote computer. This number is an accumulator and shows a running total.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER  


nwlinkspxFailuresAdapter 1.3.6.1.4.1.311.1.1.3.1.1.15.1.15
Failures Adapter is the number of connections that were dropped due to an adapter failure. This number is an accumulator and shows a running total.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER  

nwlinkspxConnectionSessionTimeouts 1.3.6.1.4.1.311.1.1.3.1.1.15.1.16
Connection Session Timeouts is the number of connections that were dropped due to a session timeout. This number is an accumulator and shows a running total.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER  

nwlinkspxConnectionsCanceled 1.3.6.1.4.1.311.1.1.3.1.1.15.1.17
Connections Canceled is the number of connections that were canceled. This number is an accumulator and shows a running total.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER  

nwlinkspxFailuresResourceRemote 1.3.6.1.4.1.311.1.1.3.1.1.15.1.18
Failures Resource Remote is the number of connections that failed because of resource problems or shortages on the remote computer. This number is an accumulator and shows a running total.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER  

nwlinkspxFailuresResourceLocal 1.3.6.1.4.1.311.1.1.3.1.1.15.1.19
Failures Resource Local is the number of connections that failed because of resource problems or shortages on the local computer. This number is an accumulator and shows a running total.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER  

nwlinkspxFailuresNotFound 1.3.6.1.4.1.311.1.1.3.1.1.15.1.20
Failures Not Found is the number of connection attempts that failed because the remote computer could not be found. This number is an accumulator and shows a running total.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER  

nwlinkspxFailuresNoListen 1.3.6.1.4.1.311.1.1.3.1.1.15.1.21
Failures No Listen is the number of connections that were rejected because the remote computer was not listening for connection requests.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER  

nwlinkspxDatagramsSentPerSec 1.3.6.1.4.1.311.1.1.3.1.1.15.1.22
Datagrams Sent/sec is the rate that datagrams are sent from the computer. A datagram is a connectionless packet whose delivery to a remote computer is not guaranteed.
Status: mandatory Access: read-only
OBJECT-TYPE    
  Counter  

nwlinkspxDatagramBytesSentPerSec 1.3.6.1.4.1.311.1.1.3.1.1.15.1.23
Datagram Bytes Sent/sec is the rate that datagram bytes are sent from the computer. A datagram is a connectionless packet whose delivery to a remote computer is not guaranteed.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER  

nwlinkspxDatagramsReceivedPerSec 1.3.6.1.4.1.311.1.1.3.1.1.15.1.24
Datagrams Received/sec is the rate that datagrams are received by the computer. A datagram is a connectionless packet whose delivery to a remote computer is not guaranteed.
Status: mandatory Access: read-only
OBJECT-TYPE    
  Counter  

nwlinkspxDatagramBytesReceivedPerSec 1.3.6.1.4.1.311.1.1.3.1.1.15.1.25
Datagram Bytes Received/sec is the rate that datagram bytes are received by the computer. A datagram is a connectionless packet whose delivery to a remote computer is not guaranteed.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER  

nwlinkspxPacketsSentPerSec 1.3.6.1.4.1.311.1.1.3.1.1.15.1.26
Packets Sent/sec is the rate that packets are sent by the computer. This counter counts all packets sent by the computer, i.e. control as well as data packets.
Status: mandatory Access: read-only
OBJECT-TYPE    
  Counter  

nwlinkspxPacketsReceivedPerSec 1.3.6.1.4.1.311.1.1.3.1.1.15.1.27
Packets Received/sec is the rate that packets are received by the computer. This counter counts all packets processed: control as well as data packets.
Status: mandatory Access: read-only
OBJECT-TYPE    
  Counter  

nwlinkspxFramesSentPerSec 1.3.6.1.4.1.311.1.1.3.1.1.15.1.28
Frames Sent/sec is the rate that data frames are sent by the computer. This counter only counts the frames (packets) that carry data.
Status: mandatory Access: read-only
OBJECT-TYPE    
  Counter  

nwlinkspxFrameBytesSentPerSec 1.3.6.1.4.1.311.1.1.3.1.1.15.1.29
Frame Bytes Sent/sec is the rate that data bytes are sent by the computer. This counter only counts the bytes in frames (packets) that carry data.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER  

nwlinkspxFramesReceivedPerSec 1.3.6.1.4.1.311.1.1.3.1.1.15.1.30
Frames Received/sec is the rate that data frames are received by the computer. This counter only counts the frames (packets) that carry data.
Status: mandatory Access: read-only
OBJECT-TYPE    
  Counter  

nwlinkspxFrameBytesReceivedPerSec 1.3.6.1.4.1.311.1.1.3.1.1.15.1.31
Frame Bytes Received/sec is the rate that data bytes are received by the computer. This counter only counts the frames (packets) that carry data.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER  

nwlinkspxFramesRe-SentPerSec 1.3.6.1.4.1.311.1.1.3.1.1.15.1.32
Frames Re-Sent/sec is the rate that data frames (packets) are re-sent by the computer. This counter only counts the frames or packets that carry data.
Status: mandatory Access: read-only
OBJECT-TYPE    
  Counter  

nwlinkspxFrameBytesRe-SentPerSec 1.3.6.1.4.1.311.1.1.3.1.1.15.1.33
Frame Bytes Re-Sent/sec is the rate that data bytes are re-sent by the computer. This counter only counts the bytes in frames that carry data.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER  

nwlinkspxFramesRejectedPerSec 1.3.6.1.4.1.311.1.1.3.1.1.15.1.34
Frames Rejected/sec is the rate that data frames are rejected. This counter only counts the frames (packets) that carry data.
Status: mandatory Access: read-only
OBJECT-TYPE    
  Counter  

nwlinkspxFrameBytesRejectedPerSec 1.3.6.1.4.1.311.1.1.3.1.1.15.1.35
Frame Bytes Rejected/sec is the rate that data bytes are rejected. This counter only counts the bytes in data frames (packets) that carry data.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER  

nwlinkspxExpirationsResponse 1.3.6.1.4.1.311.1.1.3.1.1.15.1.36
Expirations Response is the count of T1 timer expirations.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER  

nwlinkspxExpirationsAck 1.3.6.1.4.1.311.1.1.3.1.1.15.1.37
Expirations Ack is the count of T2 timer expirations
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER  

nwlinkspxWindowSendMaximum 1.3.6.1.4.1.311.1.1.3.1.1.15.1.38
Window Send Maximum is the maximum number of bytes of data that will be sent before waiting for an acknowledgment from the remote computer.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER  

nwlinkspxWindowSendAverage 1.3.6.1.4.1.311.1.1.3.1.1.15.1.39
Window Send Average is the running average number of data bytes that were sent before waiting for an acknowledgment from the remote computer.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER  

nwlinkspxPiggybackAckQueuedPerSec 1.3.6.1.4.1.311.1.1.3.1.1.15.1.40
Piggyback Ack Queued/sec is the rate that piggybacked acknowledgments are queued. Piggyback acknowledgments are acknowledgments to received packets that are to be included in the next outgoing packet to the remote computer.
Status: mandatory Access: read-only
OBJECT-TYPE    
  Counter  

nwlinkspxPiggybackAckTimeouts 1.3.6.1.4.1.311.1.1.3.1.1.15.1.41
Piggyback Ack Timeouts is the number of times that a piggyback acknowledgment could not be sent because there was no outgoing packet to the remote on which to piggyback. A piggyback ack is an acknowledgment to a received packet that is sent along in an outgoing data packet to the remote computer. If no outgoing packet is sent within the timeout period, then an ack packet is sent and this counter is incremented.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER  

rAS-Total 1.3.6.1.4.1.311.1.1.3.1.1.16
OBJECT IDENTIFIER    

rastotalBytesTransmitted 1.3.6.1.4.1.311.1.1.3.1.1.16.1
The number of bytes transmitted total for this connection.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER  

rastotalBytesReceived 1.3.6.1.4.1.311.1.1.3.1.1.16.2
The number of bytes received total for this connection.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER  

rastotalFramesTransmitted 1.3.6.1.4.1.311.1.1.3.1.1.16.3
The number of data frames transmitted total for this connection.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER  

rastotalFramesReceived 1.3.6.1.4.1.311.1.1.3.1.1.16.4
The number of data frames received total for this connection.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER  

rastotalPercentCompressionOut 1.3.6.1.4.1.311.1.1.3.1.1.16.5
The compression ratio for bytes being transmitted.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER  

rastotalPercentCompressionIn 1.3.6.1.4.1.311.1.1.3.1.1.16.6
The compression ratio for bytes being received.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER  

rastotalCRCErrors 1.3.6.1.4.1.311.1.1.3.1.1.16.7
The total number of CRC Errors for this connection. CRC Errors occur when the frame received contains erroneous data.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER  

rastotalTimeoutErrors 1.3.6.1.4.1.311.1.1.3.1.1.16.8
The total number of Timeout Errors for this connection. Timeout Errors occur when an expected is not received in time.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER  

rastotalSerialOverrunErrors 1.3.6.1.4.1.311.1.1.3.1.1.16.9
The total number of Serial Overrun Errors for this connection. Serial Overrun Errors occur when the hardware cannot handle the rate at which data is received.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER  

rastotalAlignmentErrors 1.3.6.1.4.1.311.1.1.3.1.1.16.10
The total number of Alignment Errors for this connection. Alignment Errors occur when a byte received is different from the byte expected.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER  

rastotalBufferOverrunErrors 1.3.6.1.4.1.311.1.1.3.1.1.16.11
The total number of Buffer Overrun Errors for this connection. Buffer Overrun Errors when the software cannot handle the rate at which data is received.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER  

rastotalTotalErrors 1.3.6.1.4.1.311.1.1.3.1.1.16.12
The total number of CRC, Timeout, Serial Overrun, Alignment, and Buffer Overrun Errors for this connection.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER  

rastotalBytesTransmittedPerSec 1.3.6.1.4.1.311.1.1.3.1.1.16.13
The number of bytes transmitted per second.
Status: mandatory Access: read-only
OBJECT-TYPE    
  Counter  

rastotalBytesReceivedPerSec 1.3.6.1.4.1.311.1.1.3.1.1.16.14
The number of bytes received per second.
Status: mandatory Access: read-only
OBJECT-TYPE    
  Counter  

rastotalFramesTransmittedPerSec 1.3.6.1.4.1.311.1.1.3.1.1.16.15
The number of frames transmitted per second.
Status: mandatory Access: read-only
OBJECT-TYPE    
  Counter  

rastotalFramesReceivedPerSec 1.3.6.1.4.1.311.1.1.3.1.1.16.16
The number of frames received per second.
Status: mandatory Access: read-only
OBJECT-TYPE    
  Counter  

rastotalTotalErrorsPerSec 1.3.6.1.4.1.311.1.1.3.1.1.16.17
The total number of CRC, Timeout, Serial Overrun, Alignment, and Buffer Overrun Errors per second.
Status: mandatory Access: read-only
OBJECT-TYPE    
  Counter  

rastotalTotalConnections 1.3.6.1.4.1.311.1.1.3.1.1.16.18
The total number of Remote Access connections.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER  

server 1.3.6.1.4.1.311.1.1.3.1.1.17
OBJECT IDENTIFIER    

serverBytesTotalPerSec 1.3.6.1.4.1.311.1.1.3.1.1.17.1
The number of bytes the server has sent to and received from the network. This value provides an overall indication of how busy the server is.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER  

serverBytesReceivedPerSec 1.3.6.1.4.1.311.1.1.3.1.1.17.2
The number of bytes the server has received from the network. Indicates how busy the server is.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER  

serverBytesTransmittedPerSec 1.3.6.1.4.1.311.1.1.3.1.1.17.3
The number of bytes the server has sent on the network. Indicates how busy the server is.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER  

serverSessionsTimedOut 1.3.6.1.4.1.311.1.1.3.1.1.17.4
The number of sessions that have been closed due to their idle time exceeding the autodisconnect parameter for the server. Shows whether the autodisconnect setting is helping to conserve resources.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER  

serverSessionsErroredOut 1.3.6.1.4.1.311.1.1.3.1.1.17.5
The number of sessions that have been closed due to unexpected error conditions. Indicates how frequently network problems are causing dropped sessions on the server.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER  

serverSessionsLoggedOff 1.3.6.1.4.1.311.1.1.3.1.1.17.6
The number of sessions that have terminated normally. Useful in interpreting the Sessions Times Out and Sessions Errored Out statistics--allows percentage calculations.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER  

serverSessionsForcedOff 1.3.6.1.4.1.311.1.1.3.1.1.17.7
The number of sessions that have been forced to logoff. Can indicate how many sessions were forced to logoff due to logon time constraints.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER  

serverErrorsLogon 1.3.6.1.4.1.311.1.1.3.1.1.17.8
The number of failed logon attempts to the server. Can indicate whether password guessing programs are being used to crack the security on the server.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER  

serverErrorsAccessPermissions 1.3.6.1.4.1.311.1.1.3.1.1.17.9
The number of times opens on behalf of clients have failed with STATUS_ACCESS_DENIED. Can indicate whether somebody is randomly attempting to access files in hopes of getting at something that was not properly protected.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER  

serverErrorsGrantedAccess 1.3.6.1.4.1.311.1.1.3.1.1.17.10
The number of times accesses to files opened successfully were denied. Can indicate attempts to access files without proper access authorization.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER  

serverErrorsSystem 1.3.6.1.4.1.311.1.1.3.1.1.17.11
The number of times an internal Server Error was detected. Unexpected errors usually indicate a problem with the Server.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER  

serverBlockingRequestsRejected 1.3.6.1.4.1.311.1.1.3.1.1.17.12
The number of times the server has rejected blocking SMBs due to insufficient count of free work items. Indicates whether the maxworkitem or minfreeworkitems server parameters may need tuning.
Status: mandatory Access: read-only
OBJECT-TYPE    
  Counter  

serverWorkItemShortages 1.3.6.1.4.1.311.1.1.3.1.1.17.13
The number of times STATUS_DATA_NOT_ACCEPTED was returned at receive indication time. This occurs when no work item is available or can be allocated to service the incoming request. Indicates whether the initworkitems or maxworkitems parameters may need tuning.
Status: mandatory Access: read-only
OBJECT-TYPE    
  Counter  

serverFilesOpenedTotal 1.3.6.1.4.1.311.1.1.3.1.1.17.14
The number of successful open attempts performed by the server of behalf of clients. Useful in determining the amount of file I/O, determining overhead for path-based operations, determining the effectiveness of oplocks.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER  

serverFilesOpen 1.3.6.1.4.1.311.1.1.3.1.1.17.15
The number of files currently opened in the server. Indicates current server activity.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER  

serverServerSessions 1.3.6.1.4.1.311.1.1.3.1.1.17.16
The number of sessions currently active in the server. Indicates current server activity.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER  

serverFileDirectorySearches 1.3.6.1.4.1.311.1.1.3.1.1.17.17
The number of searches for files currently active in the server. Indicates current server activity.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER  

serverPoolNonpagedBytes 1.3.6.1.4.1.311.1.1.3.1.1.17.18
The number of bytes of non-pageable computer memory the server is currently using. Can help in determining good values for the maxnonpagedmemoryusage parameter.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER  

serverPoolNonpagedFailures 1.3.6.1.4.1.311.1.1.3.1.1.17.19
The number of times allocations from nonpaged pool have failed. Indicates that the computer's physical memory is too small.
Status: mandatory Access: read-only
OBJECT-TYPE    
  Counter  

serverPoolNonpagedPeak 1.3.6.1.4.1.311.1.1.3.1.1.17.20
The maximum number of bytes of nonpaged pool the server has had in use at any one point. Indicates how much physical memory the computer should have.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER  

serverPoolPagedBytes 1.3.6.1.4.1.311.1.1.3.1.1.17.21
The number of bytes of pageable computer memory the server is currently using. Can help in determining good values for the maxpagedmemoryusage parameter.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER  

serverPoolPagedFailures 1.3.6.1.4.1.311.1.1.3.1.1.17.22
The number of times allocations from paged pool have failed. Indicates that the computer's physical memory of pagefile are too small.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER  

serverPoolPagedPeak 1.3.6.1.4.1.311.1.1.3.1.1.17.23
The maximum number of bytes of paged pool the server has had allocated. Indicates the proper sizes of the Page File(s) and physical memory.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER  

serverContextBlocksQueuedPerSec 1.3.6.1.4.1.311.1.1.3.1.1.17.24
Context Blocks Queued per second is the rate that work context blocks had to be placed on the server's FSP queue to await server action.
Status: mandatory Access: read-only
OBJECT-TYPE    
  Counter  

serverLogonPerSec 1.3.6.1.4.1.311.1.1.3.1.1.17.25
Logon/sec is the rate of all server logons
Status: mandatory Access: read-only
OBJECT-TYPE    
  Counter  

serverLogonTotal 1.3.6.1.4.1.311.1.1.3.1.1.17.26
Logon Total includes all interactive logons, network logons, service logons, successful logon, and failed logons since the machine is last rebooted.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER  

srvrqueuesserver-Work-QueuesTable 1.3.6.1.4.1.311.1.1.3.1.1.18
A table containing performance information for instances of 'server-Work-Queues' objects.
Status: mandatory Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    Srvrqueuesserver-Work-QueuesEntry

srvrqueuesserver-Work-QueuesEntry 1.3.6.1.4.1.311.1.1.3.1.1.18.1
Performance information for one particular instance of 'server-Work-Queues' object.
Status: mandatory Access: not-accessible
OBJECT-TYPE    
  Srvrqueuesserver-Work-QueuesEntry  

srvrqueuesserver-Work-QueuesIndex 1.3.6.1.4.1.311.1.1.3.1.1.18.1.1
Index.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER  

srvrqueuesserver-Work-QueuesInstance 1.3.6.1.4.1.311.1.1.3.1.1.18.1.2
Instance name.
Status: mandatory Access: read-only
OBJECT-TYPE    
  DisplayString  

srvrqueuesQueueLength 1.3.6.1.4.1.311.1.1.3.1.1.18.1.3
Queue Length is the current length of the server work queue for this CPU. A sustained queue length greater than four may indicate processor congestion. This is an instantaneous count, not an average over time.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER  

srvrqueuesActiveThreads 1.3.6.1.4.1.311.1.1.3.1.1.18.1.4
Active Threads is the number of threads currently working on a request from the server client for this CPU. The system keeps this number as low as possible to minimize unnecessary context switching. This is an instantaneous count for the CPU, not an average over time.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER  

srvrqueuesAvailableThreads 1.3.6.1.4.1.311.1.1.3.1.1.18.1.5
Available Threads is the number of server threads on this CPU not currently working on requests from a client. The server dynamically adjusts the number of threads to maximize server performance.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER  

srvrqueuesAvailableWorkItems 1.3.6.1.4.1.311.1.1.3.1.1.18.1.6
Every request from a client is represented in the server as a 'work item,' and the server maintains a pool of available work items per CPU to speed processing. This is the instantaneous number of available work items for this CPU. A sustained near-zero value indicates the need to increase the MinFreeWorkItems registry value for the Server service. This value will always be 0 in the Blocking Queue instance.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER  

srvrqueuesBorrowedWorkItems 1.3.6.1.4.1.311.1.1.3.1.1.18.1.7
Every request from a client is represented in the server as a 'work item,' and the server maintains a pool of available work items per CPU to speed processing. When a CPU runs out of work items, it borrows a free work item from another CPU. An increasing value of this running counter may indicate the need to increase the 'MaxWorkItems' or 'MinFreeWorkItems' registry values for the Server service. This value will always be 0 in the Blocking Queue instance.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER  

srvrqueuesWorkItemShortages 1.3.6.1.4.1.311.1.1.3.1.1.18.1.8
Every request from a client is represented in the server as a 'work item,' and the server maintains a pool of available work items per CPU to speed processing. A sustained value greater than zero indicates the need to increase the 'MaxWorkItems' registry value for the Server service. This value will always be 0 in the Blocking Queue instance.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER  

srvrqueuesCurrentClients 1.3.6.1.4.1.311.1.1.3.1.1.18.1.9
Current Clients is the instantaneous count of the clients being serviced by this CPU. The server actively balances the client load across all of the CPU's in the system. This value will always be 0 in the Blocking Queue instance.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER  

srvrqueuesBytesReceivedPerSec 1.3.6.1.4.1.311.1.1.3.1.1.18.1.10
The rate at which the Server is receiving bytes from the network clients on this CPU. This value is a measure of how busy the Server is.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER  

srvrqueuesBytesSentPerSec 1.3.6.1.4.1.311.1.1.3.1.1.18.1.11
The rate at which the Server is sending bytes to the network clients on this CPU. This value is a measure of how busy the Server is.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER  

srvrqueuesBytesTransferredPerSec 1.3.6.1.4.1.311.1.1.3.1.1.18.1.12
The rate at which the Server is sending and receiving bytes with the network clients on this CPU. This value is a measure of how busy the Server is.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER  

srvrqueuesReadOperationsPerSec 1.3.6.1.4.1.311.1.1.3.1.1.18.1.13
Read Operations/sec is the rate the server is performing file read operations for the clients on this CPU. This value is a measure of how busy the Server is. This value will always be 0 in the Blocking Queue instance.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER  

srvrqueuesReadBytesPerSec 1.3.6.1.4.1.311.1.1.3.1.1.18.1.14
Read Bytes/sec is the rate the server is reading data from files for the clients on this CPU. This value is a measure of how busy the Server is.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER  

srvrqueuesWriteOperationsPerSec 1.3.6.1.4.1.311.1.1.3.1.1.18.1.15
Write Operations/sec is the rate the server is performing file write operations for the clients on this CPU. This value is a measure of how busy the Server is. This value will always be 0 in the Blocking Queue instance.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER  

srvrqueuesWriteBytesPerSec 1.3.6.1.4.1.311.1.1.3.1.1.18.1.16
Write Bytes/sec is the rate the server is writing data to files for the clients on this CPU. This value is a measure of how busy the Server is.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER  

srvrqueuesTotalBytesPerSec 1.3.6.1.4.1.311.1.1.3.1.1.18.1.17
Total Bytes/sec is the rate the Server is reading and writing data to and from the files for the clients on this CPU. This value is a measure of how busy the Server is.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER  

srvrqueuesTotalOperationsPerSec 1.3.6.1.4.1.311.1.1.3.1.1.18.1.18
Total Operations/sec is the rate the Server is performing file read and file write operations for the cliens on this CPU. This value is a measure of how busy the Server is. This value will always be 0 in the Blocking Queue instance.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER  

srvrqueuesContextBlocksQueuedPerSec 1.3.6.1.4.1.311.1.1.3.1.1.18.1.19
Context Blocks Queued per second is the rate that work context blocks had to be placed on the server's FSP queue to await server action.
Status: mandatory Access: read-only
OBJECT-TYPE    
  Counter  

cache 1.3.6.1.4.1.311.1.1.3.1.1.19
OBJECT IDENTIFIER    

cacheDataMapsPerSec 1.3.6.1.4.1.311.1.1.3.1.1.19.1
Data Maps/sec is the frequency that a file system such as NTFS or HPFS maps a page of a file into the Cache to read the page.
Status: mandatory Access: read-only
OBJECT-TYPE    
  Counter  

cacheSyncDataMapsPerSec 1.3.6.1.4.1.311.1.1.3.1.1.19.2
Sync Data Maps/sec counts the frequency that a file system such as NTFS or HPFS maps a page of a file into the Cache to read the page, and wishes to wait for the Cache to retrieve the page if it is not in main memory.
Status: mandatory Access: read-only
OBJECT-TYPE    
  Counter  

cacheAsyncDataMapsPerSec 1.3.6.1.4.1.311.1.1.3.1.1.19.3
Async Data Maps/sec is the frequency that an application using a file system such as NTFS or HPFS to map a page of a file into the Cache to read the page, and does not wish to wait for the Cache to retrieve the page if it is not in main memory.
Status: mandatory Access: read-only
OBJECT-TYPE    
  Counter  

cacheDataMapHitsPercent 1.3.6.1.4.1.311.1.1.3.1.1.19.4
Data Map Hits is the percentage of Data Maps in the Cache that could be resolved without having to retrieve a page from the disk, i.e. the page was already in physical memory.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER  

cacheDataMapPinsPerSec 1.3.6.1.4.1.311.1.1.3.1.1.19.6
Data Map Pins/sec is the frequency of Data Maps in the Cache that resulted in pinning a page in main memory, an action usually preparatory to writing to the file on disk. While pinned, a page's physical address in main memory and virtual address in the Cache will not be altered.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER  

cachePinReadsPerSec 1.3.6.1.4.1.311.1.1.3.1.1.19.8
Pin Reads/sec is the frequency of reading data into the Cache preparatory to writing the data back to disk. Pages read in this fashion are pinned in memory at the completion of the read. While pinned, a page's physical address in the Cache will not be altered.
Status: mandatory Access: read-only
OBJECT-TYPE    
  Counter  

cacheSyncPinReadsPerSec 1.3.6.1.4.1.311.1.1.3.1.1.19.9
Sync Pin Reads/sec is the frequency of reading data into the Cache preparatory to writing the data back to disk. Pages read in this fashion are pinned in memory at the completion of the read. The file system will not regain control until the page is pinned in the Cache, in particular if the disk must be accessed to retrieve the page. While pinned, a page's physical address in the Cache will not be altered.
Status: mandatory Access: read-only
OBJECT-TYPE    
  Counter  

cacheAsyncPinReadsPerSec 1.3.6.1.4.1.311.1.1.3.1.1.19.10
Async Pin Reads/sec is the frequency of reading data into the Cache preparatory to writing the data back to disk. Pages read in this fashion are pinned in memory at the completion of the read. The file system will regain control immediately even if the disk must be accessed to retrieve the page. While pinned, a page's physical address will not be altered.
Status: mandatory Access: read-only
OBJECT-TYPE    
  Counter  

cachePinReadHitsPercent 1.3.6.1.4.1.311.1.1.3.1.1.19.11
Pin Read Hits is the percentage of Cache Pin Read requests that hit the Cache, i.e., did not require a disk read in order to provide access to the page in the Cache. While pinned, a page's physical address in the Cache will not be altered. The LAN Redirector uses this method for retrieving Cache information, as does the LAN Server for small transfers. This is usually the method used by the disk file systems as well.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER  

cacheCopyReadsPerSec 1.3.6.1.4.1.311.1.1.3.1.1.19.13
Copy Reads/sec is the frequency of reads from Cache pages that involve a memory copy of the data from the Cache to the application's buffer. The LAN Redirector uses this method for retrieving Cache information, as does the LAN Server for small transfers. This is a method used by the disk file systems as well.
Status: mandatory Access: read-only
OBJECT-TYPE    
  Counter  

cacheSyncCopyReadsPerSec 1.3.6.1.4.1.311.1.1.3.1.1.19.14
Sync Copy Reads/sec is the frequency of reads from Cache pages that involve a memory copy of the data from the Cache to the application's buffer. The file system will not regain control until the copy operation is complete, even if the disk must be accessed to retrieve the page.
Status: mandatory Access: read-only
OBJECT-TYPE    
  Counter  

cacheAsyncCopyReadsPerSec 1.3.6.1.4.1.311.1.1.3.1.1.19.15
Async Copy Reads/sec is the frequency of reads from Cache pages that involve a memory copy of the data from the Cache to the application's buffer. The application will regain control immediately even if the disk must be accessed to retrieve the page.
Status: mandatory Access: read-only
OBJECT-TYPE    
  Counter  

cacheCopyReadHitsPercent 1.3.6.1.4.1.311.1.1.3.1.1.19.16
Copy Read Hits is the percentage of Cache Copy Read requests that hit the Cache, i.e., did not require a disk read in order to provide access to the page in the Cache. A Copy Read is a file read operation that is satisfied by a memory copy from a Cache page to the application's buffer. The LAN Redirector uses this method for retrieving Cache information, as does the LAN Server for small transfers. This is a method used by the disk file systems as well.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER  

cacheMDLReadsPerSec 1.3.6.1.4.1.311.1.1.3.1.1.19.18
MDL Reads/sec is the frequency of reads from Cache pages that use a Memory Descriptor List (MDL) to access the data. The MDL contains the physical address of each page involved in the transfer, and thus can employ a hardware Direct Memory Access (DMA) device to effect the copy. The LAN Server uses this method for large transfers out of the server.
Status: mandatory Access: read-only
OBJECT-TYPE    
  Counter  

cacheSyncMDLReadsPerSec 1.3.6.1.4.1.311.1.1.3.1.1.19.19
Sync MDL Reads/sec is the frequency of reads from Cache pages that use a Memory Descriptor List (MDL) to access the pages. The MDL contains the physical address of each page in the transfer, thus permitting Direct Memory Access (DMA) of the pages. If the accessed page(s) are not in main memory, the caller will wait for the pages to fault in from the disk.
Status: mandatory Access: read-only
OBJECT-TYPE    
  Counter  

cacheAsyncMDLReadsPerSec 1.3.6.1.4.1.311.1.1.3.1.1.19.20
Async MDL Reads/sec is the frequency of reads from Cache pages using a Memory Descriptor List (MDL) to access the pages. The MDL contains the physical address of each page in the transfer, thus permitting Direct Memory Access (DMA) of the pages. If the accessed page(s) are not in main memory, the calling application program will not wait for the pages to fault in from disk.
Status: mandatory Access: read-only
OBJECT-TYPE    
  Counter  

cacheMDLReadHitsPercent 1.3.6.1.4.1.311.1.1.3.1.1.19.21
MDL Read Hits is the percentage of Cache Memory Descriptor List (MDL) Read requests that hit the Cache, i.e., did not require disk accesses in order to provide memory access to the page(s) in the Cache.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER  

cacheReadAheadsPerSec 1.3.6.1.4.1.311.1.1.3.1.1.19.23
Read Aheads/sec is the frequency of Cache reads where the Cache detects sequential access to a file. The read aheads permit the data to be transferred in larger blocks than those being requested by the application, reducing the overhead per access.
Status: mandatory Access: read-only
OBJECT-TYPE    
  Counter  

cacheFastReadsPerSec 1.3.6.1.4.1.311.1.1.3.1.1.19.24
Fast Reads/sec is the frequency of reads from Cache pages that bypass the installed file system and retrieve the data directly from the Cache. Normally, file I/O requests invoke the appropriate file system to retrieve data from a file, but this path permits direct retrieval of Cache data without file system involvement if the data is in the Cache. Even if the data is not in the Cache, one invocation of the file system is avoided.
Status: mandatory Access: read-only
OBJECT-TYPE    
  Counter  

cacheSyncFastReadsPerSec 1.3.6.1.4.1.311.1.1.3.1.1.19.25
Sync Fast Reads/sec is the frequency of reads from Cache pages that bypass the installed file system and retrieve the data directly from the Cache. Normally, file I/O requests invoke the appropriate file system to retrieve data from a file, but this path permits direct retrieval of Cache data without file system involvement if the data is in the Cache. Even if the data is not in the Cache, one invocation of the file system is avoided. If the data is not in the Cache, the request (application program call) will wait until the data has been retrieved from disk.
Status: mandatory Access: read-only
OBJECT-TYPE    
  Counter  

cacheAsyncFastReadsPerSec 1.3.6.1.4.1.311.1.1.3.1.1.19.26
Async Fast Reads/sec is the frequency of reads from Cache pages that bypass the installed file system and retrieve the data directly from the Cache. Normally, file I/O requests will invoke the appropriate file system to retrieve data from a file, but this path permits direct retrieval of Cache data without file system involvement if the data is in the Cache. Even if the data is not in the Cache, one invocation of the file system is avoided. If the data is not in the Cache, the request (application program call) will not wait until the data has been retrieved from disk, but will get control immediately.
Status: mandatory Access: read-only
OBJECT-TYPE    
  Counter  

cacheFastReadResourceMissesPerSec 1.3.6.1.4.1.311.1.1.3.1.1.19.27
Fast Read Resource Misses/sec is the frequency of Cache misses necessitated by the lack of available resources to satisfy the request.
Status: mandatory Access: read-only
OBJECT-TYPE    
  Counter  

cacheFastReadNotPossiblesPerSec 1.3.6.1.4.1.311.1.1.3.1.1.19.28
Fast Read Not Possibles/sec is the frequency of attempts by an Application Program Interface (API) function call to bypass the file system to get at Cache data, that could not be honored without invoking the file system after all.
Status: mandatory Access: read-only
OBJECT-TYPE    
  Counter  

cacheLazyWriteFlushesPerSec 1.3.6.1.4.1.311.1.1.3.1.1.19.29
Lazy Write Flushes/sec is the frequency the Cache's Lazy Write thread has written to disk. Lazy Writing is the process of updating the disk after the page has been changed in memory, so the application making the change to the file does not have to wait for the disk write to complete before proceeding. More than one page can be transferred on each write operation.
Status: mandatory Access: read-only
OBJECT-TYPE    
  Counter  

cacheLazyWritePagesPerSec 1.3.6.1.4.1.311.1.1.3.1.1.19.30
Lazy Write Pages/sec is the frequency the Cache's Lazy Write thread has written to disk. Lazy Writing is the process of updating the disk after the page has been changed in memory, so the application making the change to the file does not have to wait for the disk write to complete before proceeding. More than one page can be transferred on a single disk write operation.
Status: mandatory Access: read-only
OBJECT-TYPE    
  Counter  

cacheDataFlushesPerSec 1.3.6.1.4.1.311.1.1.3.1.1.19.31
Data Flushes/sec is the frequency the Cache has flushed its contents to disk as the result of a request to flush or to satisfy a write-through file write request. More than one page can be transferred on each flush operation.
Status: mandatory Access: read-only
OBJECT-TYPE    
  Counter  

cacheDataFlushPagesPerSec 1.3.6.1.4.1.311.1.1.3.1.1.19.32
Data Flush Pages/sec is the number of pages the Cache has flushed to disk as a result of a request to flush or to satisfy a write-through file write request. More than one page can be transferred on each flush operation.
Status: mandatory Access: read-only
OBJECT-TYPE    
  Counter  

mSExchangeMTA 1.3.6.1.4.1.311.1.1.3.1.1.20
OBJECT IDENTIFIER    

exchmtaAdjacentMTAAssociations 1.3.6.1.4.1.311.1.1.3.1.1.20.1
Adjacent MTA Associations is the number of open associations this MTA has to other MTAs.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER  

exchmtaMessagesPerSec 1.3.6.1.4.1.311.1.1.3.1.1.20.2
Messages/sec is the rate that messages are processed.
Status: mandatory Access: read-only
OBJECT-TYPE    
  Counter  

exchmtaMessageBytesPerSec 1.3.6.1.4.1.311.1.1.3.1.1.20.3
Message Bytes/sec is the rate that message bytes are processed.
Status: mandatory Access: read-only
OBJECT-TYPE    
  Counter  

exchmtaFreeElements 1.3.6.1.4.1.311.1.1.3.1.1.20.4
Free Elements is the number of free buffer elements in the MTA pool.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER  

exchmtaFreeHeaders 1.3.6.1.4.1.311.1.1.3.1.1.20.5
Free Headers is the number of free buffer headers in the MTA pool.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER  

exchmtaAdminConnections 1.3.6.1.4.1.311.1.1.3.1.1.20.6
Admin Connections is the number of Microsoft Exchange Administrator programs connected to this MTA.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER  

exchmtaThreadsInUse 1.3.6.1.4.1.311.1.1.3.1.1.20.7
Threads in Use is the number of threads in use by the MTA (does not include RPC threads). This number can be used to determine whether additional processors could be of benefit.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER  

exchmtaWorkQueueLength 1.3.6.1.4.1.311.1.1.3.1.1.20.8
Work Queue Length is the number of outstanding messages in the Work Queue, which indicates the number of messages not yet processed to completion by the MTA.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER  

exchmtaXAPIGateways 1.3.6.1.4.1.311.1.1.3.1.1.20.9
XAPI Gateways is the number of gateways connected to the MTA using the XAPI MT/OM interface. A single gateway may have multiple XAPI gateway sessions.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER  

exchmtaXAPIClients 1.3.6.1.4.1.311.1.1.3.1.1.20.10
XAPI Clients is the number of XAPI clients connected to the MTA using the XAPI MA/OM interface. A single client may have multiple XAPI client sessions.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER  

exchmtaDiskFileDeletesPerSec 1.3.6.1.4.1.311.1.1.3.1.1.20.11
Disk File Deletes/sec is the rate of disk file delete operations.
Status: mandatory Access: read-only
OBJECT-TYPE    
  Counter  

exchmtaDiskFileSyncsPerSec 1.3.6.1.4.1.311.1.1.3.1.1.20.12
Disk File Syncs/sec is the rate of disk file sync operations.
Status: mandatory Access: read-only
OBJECT-TYPE    
  Counter  

exchmtaDiskFileOpensPerSec 1.3.6.1.4.1.311.1.1.3.1.1.20.13
Disk File Opens/sec is the rate of disk file open operations.
Status: mandatory Access: read-only
OBJECT-TYPE    
  Counter  

exchmtaDiskFileReadsPerSec 1.3.6.1.4.1.311.1.1.3.1.1.20.14
Disk File Reads/sec is the rate of disk file read operations.
Status: mandatory Access: read-only
OBJECT-TYPE    
  Counter  

exchmtaDiskFileWritesPerSec 1.3.6.1.4.1.311.1.1.3.1.1.20.15
Disk File Writes/sec is the rate of disk file write operations.
Status: mandatory Access: read-only
OBJECT-TYPE    
  Counter  

exchmtaExDSReadCallsPerSec 1.3.6.1.4.1.311.1.1.3.1.1.20.16
ExDS Read Calls/sec is the rate of read calls to the directory service.
Status: mandatory Access: read-only
OBJECT-TYPE    
  Counter  

exchmtaXAPIReceiveBytesPerSec 1.3.6.1.4.1.311.1.1.3.1.1.20.17
XAPI Receive Bytes/sec is the rate that bytes are received over a XAPI connection.
Status: mandatory Access: read-only
OBJECT-TYPE    
  Counter  

exchmtaXAPITransmitBytesPerSec 1.3.6.1.4.1.311.1.1.3.1.1.20.18
XAPI Transmit Bytes/sec is the rate that bytes are transmitted over a XAPI connection.
Status: mandatory Access: read-only
OBJECT-TYPE    
  Counter  

exchmtaAdminInterfaceReceiveBytesPerSec 1.3.6.1.4.1.311.1.1.3.1.1.20.19
Admin Interface Receive Bytes/sec is the rate that bytes are received over an Admin connection.
Status: mandatory Access: read-only
OBJECT-TYPE    
  Counter  

exchmtaAdminInterfaceTransmitBytesPerSec 1.3.6.1.4.1.311.1.1.3.1.1.20.20
Admin Interface Transmit Bytes/sec is the rate that bytes are transmitted over an Admin connection.
Status: mandatory Access: read-only
OBJECT-TYPE    
  Counter  

exchmtaLANReceiveBytesPerSec 1.3.6.1.4.1.311.1.1.3.1.1.20.21
LAN Receive Bytes/sec is the rate that bytes are received over a LAN from MTAs.
Status: mandatory Access: read-only
OBJECT-TYPE    
  Counter  

exchmtaLANTransmitBytesPerSec 1.3.6.1.4.1.311.1.1.3.1.1.20.22
LAN Transmit Bytes/sec is the rate that bytes are transmitted over a LAN to MTAs.
Status: mandatory Access: read-only
OBJECT-TYPE    
  Counter  

exchmtaRASReceiveBytesPerSec 1.3.6.1.4.1.311.1.1.3.1.1.20.23
RAS Receive Bytes/sec is the rate that bytes are received over a RAS connection.
Status: mandatory Access: read-only
OBJECT-TYPE    
  Counter  

exchmtaRASTransmitBytesPerSec 1.3.6.1.4.1.311.1.1.3.1.1.20.24
RAS Transmit Bytes/sec is the rate that bytes are transmitted over a RAS connection.
Status: mandatory Access: read-only
OBJECT-TYPE    
  Counter  

exchmtaTCPPerIPReceiveBytesPerSec 1.3.6.1.4.1.311.1.1.3.1.1.20.25
TCP/IP Receive Bytes/sec is the rate that bytes are received over a TCP/IP connection.
Status: mandatory Access: read-only
OBJECT-TYPE    
  Counter  

exchmtaTCPPerIPTransmitBytesPerSec 1.3.6.1.4.1.311.1.1.3.1.1.20.26
TCP/IP Transmit Bytes/sec is the rate that bytes are transmitted over a TCP/IP connection.
Status: mandatory Access: read-only
OBJECT-TYPE    
  Counter  

exchmtaTP4ReceiveBytesPerSec 1.3.6.1.4.1.311.1.1.3.1.1.20.27
TP4 Receive Bytes/sec is the rate that bytes are received over a TP4 connection.
Status: mandatory Access: read-only
OBJECT-TYPE    
  Counter  

exchmtaTP4TransmitBytesPerSec 1.3.6.1.4.1.311.1.1.3.1.1.20.28
TP4 Transmit Bytes/sec is the rate that bytes are transmitted over a TP4 connection.
Status: mandatory Access: read-only
OBJECT-TYPE    
  Counter  

exchmtaX25ReceiveBytesPerSec 1.3.6.1.4.1.311.1.1.3.1.1.20.29
X.25 Receive Bytes/sec is the rate that bytes are received over an X.25 connection.
Status: mandatory Access: read-only
OBJECT-TYPE    
  Counter  

exchmtaX25TransmitBytesPerSec 1.3.6.1.4.1.311.1.1.3.1.1.20.30
X.25 Transmit Bytes/sec is the rate that bytes are transmitted over an X.25 connection.
Status: mandatory Access: read-only
OBJECT-TYPE    
  Counter  

exchmtaDeferredDeliveryMsgs 1.3.6.1.4.1.311.1.1.3.1.1.20.31
Deferred Delivery Msgs is the total number of deferred delivery messages currently stored in the MTA.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER  

exchmtaTotalRecipientsQueued 1.3.6.1.4.1.311.1.1.3.1.1.20.32
Total Recipients Queued is the total number of recipients specified in all messages currently stored in the MTA.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER  

exchmtaTotalSuccessfulConversions 1.3.6.1.4.1.311.1.1.3.1.1.20.33
Total Successful Conversions is the total number of messages successfully converted from one form to another since MTA initialization.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER  

exchmtaTotalFailedConversions 1.3.6.1.4.1.311.1.1.3.1.1.20.34
Total Failed Conversions is the total number of messages which failed to be converted from one form to another since MTA initialization.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER  

exchmtaTotalLoopsDetected 1.3.6.1.4.1.311.1.1.3.1.1.20.35
Total Loops Detected is the total number of messages detected to have looped since MTA initialization.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER  

exchmtaInboundMessagesTotal 1.3.6.1.4.1.311.1.1.3.1.1.20.36
Inbound Messages Total is the total number of messages received since MTA initialization.
Status: mandatory Access: read-only
OBJECT-TYPE    
  Counter  

exchmtaOutboundMessagesTotal 1.3.6.1.4.1.311.1.1.3.1.1.20.37
Outbound Messages Total is the total number of messages transmitted since MTA initialization.
Status: mandatory Access: read-only
OBJECT-TYPE    
  Counter  

exchmtaInboundBytesTotal 1.3.6.1.4.1.311.1.1.3.1.1.20.38
Inbound Bytes Total is the total volume of message content received since MTA initialization, measured in kilobytes.
Status: mandatory Access: read-only
OBJECT-TYPE    
  Counter  

exchmtaWorkQueueBytes 1.3.6.1.4.1.311.1.1.3.1.1.20.39
Work Queue Bytes is the total volume of message content currently stored in the MTA, measured in kilobytes.
Status: mandatory Access: read-only
OBJECT-TYPE    
  Counter  

exchmtaOutboundBytesTotal 1.3.6.1.4.1.311.1.1.3.1.1.20.40
Outbound Bytes Total is the total volume of message content transmitted since MTA initialization, measured in kilobytes.
Status: mandatory Access: read-only
OBJECT-TYPE    
  Counter  

exchmtaTotalRecipientsInbound 1.3.6.1.4.1.311.1.1.3.1.1.20.41
Total Recipients Inbound is the total number of recipients specified in all messages received since MTA initialization.
Status: mandatory Access: read-only
OBJECT-TYPE    
  Counter  

exchmtaTotalRecipientsOutbound 1.3.6.1.4.1.311.1.1.3.1.1.20.42
Total Recipients Outbound is the total number of recipients specified in all messages transmitted since MTA initialization.
Status: mandatory Access: read-only
OBJECT-TYPE    
  Counter  

exchmtaconnmSExchangeMTA-ConnectionsTable 1.3.6.1.4.1.311.1.1.3.1.1.21
A table containing performance information for instances of 'mSExchangeMTA-Connections' objects.
Status: mandatory Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    ExchmtaconnmSExchangeMTA-ConnectionsEntry

exchmtaconnmSExchangeMTA-ConnectionsEntry 1.3.6.1.4.1.311.1.1.3.1.1.21.1
Performance information for one particular instance of 'mSExchangeMTA-Connections' object.
Status: mandatory Access: not-accessible
OBJECT-TYPE    
  ExchmtaconnmSExchangeMTA-ConnectionsEntry  

exchmtaconnmSExchangeMTA-ConnectionsIndex 1.3.6.1.4.1.311.1.1.3.1.1.21.1.1
Index.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER  

exchmtaconnmSExchangeMTA-ConnectionsInstance 1.3.6.1.4.1.311.1.1.3.1.1.21.1.2
Instance name.
Status: mandatory Access: read-only
OBJECT-TYPE    
  DisplayString  

exchmtaconnAssociations 1.3.6.1.4.1.311.1.1.3.1.1.21.1.3
Associations is the number of associations between the MTA and the connected entity. MTAs may open multiple associations if additional transfer throughput is necessary.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER  

exchmtaconnReceiveBytesPerSec 1.3.6.1.4.1.311.1.1.3.1.1.21.1.4
Receive Bytes/sec is the rate that bytes are received from the connected entity.
Status: mandatory Access: read-only
OBJECT-TYPE    
  Counter  

exchmtaconnSendBytesPerSec 1.3.6.1.4.1.311.1.1.3.1.1.21.1.5
Send Bytes/sec is the rate that bytes are sent to the connected entity.
Status: mandatory Access: read-only
OBJECT-TYPE    
  Counter  

exchmtaconnReceiveMessagesPerSec 1.3.6.1.4.1.311.1.1.3.1.1.21.1.6
Receive Messages/sec is the rate that messages are received from the connected entity.
Status: mandatory Access: read-only
OBJECT-TYPE    
  Counter  

exchmtaconnSendMessagesPerSec 1.3.6.1.4.1.311.1.1.3.1.1.21.1.7
Send Messages/sec is the rate that messages are sent to the connected entity.
Status: mandatory Access: read-only
OBJECT-TYPE    
  Counter  

exchmtaconnQueueLength 1.3.6.1.4.1.311.1.1.3.1.1.21.1.8
Queue Length is the number of outstanding messages queued for transfer to the entity.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER  

exchmtaconnConnectorIndex 1.3.6.1.4.1.311.1.1.3.1.1.21.1.9
Connector Index is a unique index associated with a connector entity.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER  

exchmtaconnInboundRejectedTotal 1.3.6.1.4.1.311.1.1.3.1.1.21.1.10
Inbound Rejected Total is the total number of messages rejected from this entity since MTA initialization.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER  

exchmtaconnTotalRecipientsQueued 1.3.6.1.4.1.311.1.1.3.1.1.21.1.11
Total Recipients Queued is the total number of recipients specified in all messages currently stored in this entity's queue.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER  

exchmtaconnOldestMessageQueued 1.3.6.1.4.1.311.1.1.3.1.1.21.1.12
Oldest Message Queued is the time (secs) since the oldest message in this entity's queue was placed in the queue.
Status: mandatory Access: read-only
OBJECT-TYPE    
  TimeTicks  

exchmtaconnCurrentInboundAssociations 1.3.6.1.4.1.311.1.1.3.1.1.21.1.13
Current Inbound Associations is the current number of inbound (remote initiated) associations with the entity.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER  

exchmtaconnCurrentOutboundAssociations 1.3.6.1.4.1.311.1.1.3.1.1.21.1.14
Current Outbound Associations is the current number of outbound (locally initiated) associations with the entity.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER  

exchmtaconnCumulativeInboundAssociations 1.3.6.1.4.1.311.1.1.3.1.1.21.1.15
Cumulative Inbound Associations is the total number of inbound (remote initiated) associations with the entity, since MTA initialization.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER  

exchmtaconnCumulativeOutboundAssociations 1.3.6.1.4.1.311.1.1.3.1.1.21.1.16
Cumulative Outbound Associations is the total number of outbound (locally initiated) associations with the entity, since MTA initialization.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER  

exchmtaconnLastInboundAssociation 1.3.6.1.4.1.311.1.1.3.1.1.21.1.17
Last Inbound Association is the time (secs) since the last time an inbound (remote initiated) association for this entity was active.
Status: mandatory Access: read-only
OBJECT-TYPE    
  TimeTicks  

exchmtaconnLastOutboundAssociation 1.3.6.1.4.1.311.1.1.3.1.1.21.1.18
Last Outbound Association is the time (secs) since the last time an outbound (locally initiated) association for this entity was active.
Status: mandatory Access: read-only
OBJECT-TYPE    
  TimeTicks  

exchmtaconnRejectedInboundAssociations 1.3.6.1.4.1.311.1.1.3.1.1.21.1.19
Rejected Inbound Associations is the total number of inbound (remote initiated) associations that have been rejected, since MTA initialization.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER  

exchmtaconnFailedOutboundAssociations 1.3.6.1.4.1.311.1.1.3.1.1.21.1.20
Failed Outbound Associations is the total number of outbound (locally initiated) associations that have failed, since MTA initialization.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER  

exchmtaconnNextAssociationRetry 1.3.6.1.4.1.311.1.1.3.1.1.21.1.21
Next Association Retry is the time (secs since 00:00 1st Jan 1970) when this entity is next scheduled to attempt to open an association.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER  

exchmtaconnInboundRejectReason 1.3.6.1.4.1.311.1.1.3.1.1.21.1.22
Inbound Reject Reason is the reject reason code, if any, for the last association rejected from this entity.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER  

exchmtaconnOutboundFailureReason 1.3.6.1.4.1.311.1.1.3.1.1.21.1.23
Outbound Failure Reason is the failure reason code, if any, for the last association attempt to this entity.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER  

exchmtaconnInboundMessagesTotal 1.3.6.1.4.1.311.1.1.3.1.1.21.1.24
Inbound Messages Total is the total number of messages received from this entity since MTA initialization.
Status: mandatory Access: read-only
OBJECT-TYPE    
  Counter  

exchmtaconnOutboundMessagesTotal 1.3.6.1.4.1.311.1.1.3.1.1.21.1.25
Outbound Messages Total is the total number of messages transmitted to this entity since MTA initialization.
Status: mandatory Access: read-only
OBJECT-TYPE    
  Counter  

exchmtaconnInboundBytesTotal 1.3.6.1.4.1.311.1.1.3.1.1.21.1.26
Inbound Bytes Total is the total volume of message content received from this entity since MTA initialization, measured in kilobytes.
Status: mandatory Access: read-only
OBJECT-TYPE    
  Counter  

exchmtaconnQueuedBytes 1.3.6.1.4.1.311.1.1.3.1.1.21.1.27
Queued Bytes is the total volume of message content currently stored in this entity's queue, measured in kilobytes.
Status: mandatory Access: read-only
OBJECT-TYPE    
  Counter  

exchmtaconnOutboundBytesTotal 1.3.6.1.4.1.311.1.1.3.1.1.21.1.28
Outbound Bytes Total is the total volume of message content transmitted to this entity since MTA initialization, measured in kilobytes.
Status: mandatory Access: read-only
OBJECT-TYPE    
  Counter  

exchmtaconnTotalRecipientsInbound 1.3.6.1.4.1.311.1.1.3.1.1.21.1.29
Total Recipients Inbound is the total number of recipients specified in all messages received from this entity since MTA initialization.
Status: mandatory Access: read-only
OBJECT-TYPE    
  Counter  

exchmtaconnTotalRecipientsOutbound 1.3.6.1.4.1.311.1.1.3.1.1.21.1.30
Total Recipients Outbound is the total number of recipients specified in all messages transmitted to this entity since MTA initialization.
Status: mandatory Access: read-only
OBJECT-TYPE    
  Counter  

mSExchangeIMC 1.3.6.1.4.1.311.1.1.3.1.1.22
OBJECT IDENTIFIER    

exchimcQueuedMTS-IN 1.3.6.1.4.1.311.1.1.3.1.1.22.1
The number of messages awaiting final delivery in MS Exchange Server
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER  

exchimcBytesQueuedMTS-IN 1.3.6.1.4.1.311.1.1.3.1.1.22.2
The size, in bytes, of the messages that have been converted from Internet Mail and are awaiting final delivery within MS Exchange Server
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER  

exchimcMessagesEnteringMTS-IN 1.3.6.1.4.1.311.1.1.3.1.1.22.3
The number of messages entering the MTS-IN folder after conversion from Internet Mail format per hour
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER  

exchimcQueuedMTS-OUT 1.3.6.1.4.1.311.1.1.3.1.1.22.4
The number of messages waiting to be converted to Internet Mail format
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER  

exchimcBytesQueuedMTS-OUT 1.3.6.1.4.1.311.1.1.3.1.1.22.5
The size, in bytes, of the messages waiting to be converted to Internet Mail format
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER  

exchimcMessagesEnteringMTS-OUT 1.3.6.1.4.1.311.1.1.3.1.1.22.6
Messages that have entered the Internet Mail Service
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER  

exchimcMessagesLeavingMTS-OUT 1.3.6.1.4.1.311.1.1.3.1.1.22.7
The number of messages entering the Outbound Queue per hour
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER  

exchimcConnectionsInbound 1.3.6.1.4.1.311.1.1.3.1.1.22.8
The number of current SMTP connections to the Internet Mail Service established by other SMTP hosts
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER  

exchimcConnectionsOutbound 1.3.6.1.4.1.311.1.1.3.1.1.22.9
The number of current SMTP connections the Internet Mail Service has established to other SMTP hosts
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER  

exchimcConnectionsTotalOutbound 1.3.6.1.4.1.311.1.1.3.1.1.22.10
The total number of successful SMTP connections that the Internet Mail Service has established since it was started
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER  

exchimcConnectionsTotalInbound 1.3.6.1.4.1.311.1.1.3.1.1.22.11
The total number of SMTP connections the Internet Mail Service has accepted from other hosts since it was started
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER  

exchimcConnectionsTotalRejected 1.3.6.1.4.1.311.1.1.3.1.1.22.12
The total number of SMTP connections that the Internet Mail Service has rejected from other hosts since it was started
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER  

exchimcConnectionsTotalFailed 1.3.6.1.4.1.311.1.1.3.1.1.22.13
The total number of SMTP connections the Internet Mail Service has attempted to other hosts that failed since it was started
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER  

exchimcQueuedOutbound 1.3.6.1.4.1.311.1.1.3.1.1.22.14
The number of messages from MS Exchange Server, that are queued to be delivered to the Internet
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER  

exchimcQueuedInbound 1.3.6.1.4.1.311.1.1.3.1.1.22.15
The number of messages received from the Internet destined for MS Exchange Server
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER  

exchimcNDRsTotalInbound 1.3.6.1.4.1.311.1.1.3.1.1.22.16
The total number of Non-delivery reports generated for inbound mail
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER  

exchimcNDRsTotalOutbound 1.3.6.1.4.1.311.1.1.3.1.1.22.17
The total number of Non-delivery reports generated for outbound mail
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER  

exchimcTotalInboundKilobytes 1.3.6.1.4.1.311.1.1.3.1.1.22.18
The total kilobytes of message data transferred into the MS Exchange Server
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER  

exchimcTotalOutboundKilobytes 1.3.6.1.4.1.311.1.1.3.1.1.22.19
The total kilobytes of message data transferred out of the MS Exchange Server
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER  

exchimcInboundMessagesTotal 1.3.6.1.4.1.311.1.1.3.1.1.22.20
The total number of Internet messages delivered into MS Exchange Server
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER  

exchimcOutboundMessagesTotal 1.3.6.1.4.1.311.1.1.3.1.1.22.21
The total number of outbound messages delivered to their destinations
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER  

exchimcInboundBytesPerHr 1.3.6.1.4.1.311.1.1.3.1.1.22.22
The hourly rate of bytes transferred to the MS Exchange Server
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER  

exchimcOutboundBytesPerHr 1.3.6.1.4.1.311.1.1.3.1.1.22.23
The hourly rate of bytes transferred to the Internet
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER  

exchimcInboundMessagesPerHr 1.3.6.1.4.1.311.1.1.3.1.1.22.24
The hourly rate messages are transferred to the MS Exchange server
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER  

exchimcOutboundMessagesPerHr 1.3.6.1.4.1.311.1.1.3.1.1.22.25
The hourly rate messages are transferred to the Internet
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER  

exchimcOutboundConnectionsPerHr 1.3.6.1.4.1.311.1.1.3.1.1.22.26
The hourly rate at which outbound connections were made
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER  

exchimcInboundConnectionsPerHr 1.3.6.1.4.1.311.1.1.3.1.1.22.27
The hourly rate at which inbound connections were received
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER  

exchimcTotalMessagesQueued 1.3.6.1.4.1.311.1.1.3.1.1.22.28
Total messages waiting in the Internet Mail Service queues
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER  

exchimcTotalKilobytesQueued 1.3.6.1.4.1.311.1.1.3.1.1.22.29
Total kilobytes of message data queued in the Internet Mail Service queues
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER  

exchimcTotalInboundRecipients 1.3.6.1.4.1.311.1.1.3.1.1.22.30
Total number of recipients processed inbound since the Internet Mail Service was started
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER  

exchimcTotalOutboundRecipients 1.3.6.1.4.1.311.1.1.3.1.1.22.31
Total number of recipients processed outbound since the Internet Mail Service was started
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER  

exchimcTotalRecipientsQueued 1.3.6.1.4.1.311.1.1.3.1.1.22.32
Total number of recipients in the Internet Mail Service queues
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER  

exchimcTotalSuccessfulConversions 1.3.6.1.4.1.311.1.1.3.1.1.22.33
Total message format conversions between internet format and Exchange format that succeeded.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER  

exchimcTotalFailedConversions 1.3.6.1.4.1.311.1.1.3.1.1.22.34
Total message format conversions between internet format and Exchange format that failed.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER  

exchimcTotalLoopsDetected 1.3.6.1.4.1.311.1.1.3.1.1.22.35
Total number of messages NDRd because they appeared to be looping infinitely.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER  

mSExchangeIS 1.3.6.1.4.1.311.1.1.3.1.1.23
OBJECT IDENTIFIER    

exchisRPCPacketsPerSec 1.3.6.1.4.1.311.1.1.3.1.1.23.1
RPC Packets/sec is the rate that RPC packets are processed.
Status: mandatory Access: read-only
OBJECT-TYPE    
  Counter  

exchisRPCOperationsPerSec 1.3.6.1.4.1.311.1.1.3.1.1.23.2
RPC Operations/sec is the rate that RPC operations occur.
Status: mandatory Access: read-only
OBJECT-TYPE    
  Counter  

exchisReadBytesRPCClientsPerSec 1.3.6.1.4.1.311.1.1.3.1.1.23.3
Read Bytes RPC Clients/sec is the rate that bytes are read from RPC clients.
Status: mandatory Access: read-only
OBJECT-TYPE    
  Counter  

exchisWriteBytesRPCClientsPerSec 1.3.6.1.4.1.311.1.1.3.1.1.23.4
Write Bytes RPC Clients/sec is the rate that bytes are written to RPC clients.
Status: mandatory Access: read-only
OBJECT-TYPE    
  Counter  

exchisPushNotificationsGeneratedPerSec 1.3.6.1.4.1.311.1.1.3.1.1.23.5
Push Notifications Generated/sec is the rate at which notifications are being sent to clients that have registered for notifications of changes to tables in the information store.
Status: mandatory Access: read-only
OBJECT-TYPE    
  Counter  

exchisPushNotificationsSkippedPerSec 1.3.6.1.4.1.311.1.1.3.1.1.23.6
Push Notifications Skipped/sec is the number of push notifications that have been skipped by caching at the server.
Status: mandatory Access: read-only
OBJECT-TYPE    
  Counter  

exchisRPCRequests 1.3.6.1.4.1.311.1.1.3.1.1.23.7
RPC Requests is the number of client requests that are currently being processed by the information store.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER  

exchisRPCRequestsPeak 1.3.6.1.4.1.311.1.1.3.1.1.23.8
RPC Requests Peak is the maximum number of client requests that were processed simultaneously by the information store since it was started.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER  

exchisUserCount 1.3.6.1.4.1.311.1.1.3.1.1.23.9
User Count is the number of users connected to the information store.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER  

exchisActiveUserCount 1.3.6.1.4.1.311.1.1.3.1.1.23.10
Number of user connections that have shown some activity in the last 10 minutes.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER  

exchisMaximumUsers 1.3.6.1.4.1.311.1.1.3.1.1.23.11
Maximum Users is the maximum number of concurrent users since startup.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER  

exchisAnonymousUserCount 1.3.6.1.4.1.311.1.1.3.1.1.23.12
Anonymous User Count is the number of anonymous users connected to the information store.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER  

exchisActiveAnonymousUserCount 1.3.6.1.4.1.311.1.1.3.1.1.23.13
Number of active users.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER  

exchisMaximumAnonymousUsers 1.3.6.1.4.1.311.1.1.3.1.1.23.14
The maximum number of anonymous users since startup.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER  

exchisConnectionCount 1.3.6.1.4.1.311.1.1.3.1.1.23.15
Connection Count is the number of client processes connected to the information store.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER  

exchisActiveConnectionCount 1.3.6.1.4.1.311.1.1.3.1.1.23.16
Number of connections that have shown some activity in the last 10 minutes.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER  

exchisMaximumConnections 1.3.6.1.4.1.311.1.1.3.1.1.23.17
The maximum number of concurrent connections since startup.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER  

exchisPushNotificationsCacheSize 1.3.6.1.4.1.311.1.1.3.1.1.23.18
The current size of the Push Notifications Cache.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER  

exchisPeakPushNotificationsCacheSize 1.3.6.1.4.1.311.1.1.3.1.1.23.19
The maximum size of the Push Notifications Cache.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER  

exchisDatabaseSessionHitRate 1.3.6.1.4.1.311.1.1.3.1.1.23.20
Database Session Hit Rate is the percent hit rate on re-using database sessions.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER  

exchisIMAPMessagesSent 1.3.6.1.4.1.311.1.1.3.1.1.23.22
Messages Sent to clients connected via the IMAP external network interface.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER  

exchisIMAPCommandsIssued 1.3.6.1.4.1.311.1.1.3.1.1.23.23
Total number of commands issued by clients connected via the IMAP external network interface
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER  

exchisIMAPMessageSendRate 1.3.6.1.4.1.311.1.1.3.1.1.23.24
Rate at which messages are sent to clients connected via the IMAP external network interface.
Status: mandatory Access: read-only
OBJECT-TYPE    
  Counter  

exchisIMAPCommandsIssuedRate 1.3.6.1.4.1.311.1.1.3.1.1.23.25
Rate at which commands are issued by clients connected via the IMAP external network interface
Status: mandatory Access: read-only
OBJECT-TYPE    
  Counter  

exchisPOP3MessagesSent 1.3.6.1.4.1.311.1.1.3.1.1.23.26
Messages Sent to clients connected via the POP3 external network interface.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER  

exchisPOP3CommandsIssued 1.3.6.1.4.1.311.1.1.3.1.1.23.27
Total number of commands issued by clients connected via the POP3 external network interface
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER  

exchisPOP3MessagesSendRate 1.3.6.1.4.1.311.1.1.3.1.1.23.28
Rate at which messages are sent to clients connected via the POP3 external network interface.
Status: mandatory Access: read-only
OBJECT-TYPE    
  Counter  

exchisPOP3CommandsIssuedRate 1.3.6.1.4.1.311.1.1.3.1.1.23.29
Rate at which commands are issued by clients connected via the POP3 external network interface
Status: mandatory Access: read-only
OBJECT-TYPE    
  Counter  

exchisNNTPMessagesRead 1.3.6.1.4.1.311.1.1.3.1.1.23.30
NNTP Messages Read is the the total number of messages sent from the information store to NNTP clients since service startup.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER  

exchisNNTPMessagesPosted 1.3.6.1.4.1.311.1.1.3.1.1.23.31
NNTP Messages Posted is the total number of messages posted by NNTP clients into the information store since service startup.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER  

exchisNNTPFailedPosts 1.3.6.1.4.1.311.1.1.3.1.1.23.32
NNTP Failed Posts is the total number of messages posted by NNTP clients that were rejected due to missing required headers or other errors.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER  

exchisNewsfeedMessagesReceived 1.3.6.1.4.1.311.1.1.3.1.1.23.33
Newsfeed Messages Received is the total number of messages received into the information store from NNTP newsfeeds since service startup.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER  

exchisNewsfeedInboundRejectedMessages 1.3.6.1.4.1.311.1.1.3.1.1.23.34
Newsfeed Inbound Rejected Messages is the total number of messages received in newsfeeds from other NNTP servers that have been rejected as duplicates or due to errors.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER  

exchisNNTPCommandsIssued 1.3.6.1.4.1.311.1.1.3.1.1.23.35
Total number of commands issued by clients connected via the NNTP external network interface
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER  

exchisNNTPMessagesReadRate 1.3.6.1.4.1.311.1.1.3.1.1.23.36
Rate at which messages are sent to NNTP clients
Status: mandatory Access: read-only
OBJECT-TYPE    
  Counter  

exchisNNTPMessagesPostedRate 1.3.6.1.4.1.311.1.1.3.1.1.23.37
Rate at which NNTP messages are posted by NNTP clients
Status: mandatory Access: read-only
OBJECT-TYPE    
  Counter  

exchisNNTPFailedPostsRate 1.3.6.1.4.1.311.1.1.3.1.1.23.38
Rate at which messages posted by NNTP clients are rejected
Status: mandatory Access: read-only
OBJECT-TYPE    
  Counter  

exchisNewsfeedMessagesReceivedRate 1.3.6.1.4.1.311.1.1.3.1.1.23.39
Rate at which messages are received into the information store from NNTP newsfeeds
Status: mandatory Access: read-only
OBJECT-TYPE    
  Counter  

exchisNewsfeedInboundRejectedMessagesRate 1.3.6.1.4.1.311.1.1.3.1.1.23.40
Rate at which messages received in newsfeeds from other NNTP servers are rejected
Status: mandatory Access: read-only
OBJECT-TYPE    
  Counter  

exchisNNTPCommandsIssuedRate 1.3.6.1.4.1.311.1.1.3.1.1.23.41
Rate at which commands are issued by clients connected via the NNTP external network interface
Status: mandatory Access: read-only
OBJECT-TYPE    
  Counter  

exchisNewsfeedMessagesSent 1.3.6.1.4.1.311.1.1.3.1.1.23.42
Newsfeed Messages Sent is the total number of messages sent from the information store to other NNTP servers by the Internet News Service since startup.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER  

exchisNewsfeedMessagesSentPerSec 1.3.6.1.4.1.311.1.1.3.1.1.23.43
Newsfeed Messages Sent/sec is the rate at which messages are sent from the information store to other NNTP servers by the Internet News Service.
Status: mandatory Access: read-only
OBJECT-TYPE    
  Counter  

exchisNewsfeedBytesSent 1.3.6.1.4.1.311.1.1.3.1.1.23.44
Newsfeed Bytes Sent is the total number of bytes sent from the information store to other NNTP servers by the Internet News Service since startup.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER  

exchisNewsfeedBytesSentPerSec 1.3.6.1.4.1.311.1.1.3.1.1.23.45
Newsfeed Bytes Sent/sec is the rate data is sent from the information store to other NNTP servers by the Internet News Service.
Status: mandatory Access: read-only
OBJECT-TYPE    
  Counter  

exchisNewsfeedOutboundRejectedMessages 1.3.6.1.4.1.311.1.1.3.1.1.23.46
Newsfeed Outbound Rejected Messages is the total number of messages sent in newsfeeds to other NNTP servers that have been rejected as duplicates or due to errors since service startup.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER  

exchisNNTPOutboundConnections 1.3.6.1.4.1.311.1.1.3.1.1.23.47
NNTP Outbound Connections is the total number of outbound TCP/IP connections to other NNTP servers that have been made by the Internet News Service for push or pull newsfeeds since startup.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER  

exchisNNTPCurrentOutboundConnections 1.3.6.1.4.1.311.1.1.3.1.1.23.48
NNTP Current Outbound Connections is the current number of outbound TCP/IP connections from the Internet News Service to other NNTP servers for push or pull newsfeeds.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER  

exchisNumberOfArticleIndexTableRowsExpired 1.3.6.1.4.1.311.1.1.3.1.1.23.49
Number of article index table rows expired
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER  

mSExchangeIS-Public 1.3.6.1.4.1.311.1.1.3.1.1.24
OBJECT IDENTIFIER    

exchispubSendQueueSize 1.3.6.1.4.1.311.1.1.3.1.1.24.1
Send Queue Size is the number of messages in the public information store's send queue.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER  

exchispubReceiveQueueSize 1.3.6.1.4.1.311.1.1.3.1.1.24.2
Receive Queue Size is the number of messages in the public information store's receive queue.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER  

exchispubCategorizationCount 1.3.6.1.4.1.311.1.1.3.1.1.24.3
Categorization Count is the number of categorizations that exist in the information store. Categorizations are created when a user creates a filtered view or performs a search. When the information store must maintain an excessive number of categorizations, performance can be affected.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER  

exchispubMessagesDelivered 1.3.6.1.4.1.311.1.1.3.1.1.24.4
Messages Delivered is the total number of messages delivered to all recipients since startup.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER  

exchispubMessageRecipientsDelivered 1.3.6.1.4.1.311.1.1.3.1.1.24.5
Message Recipients Delivered is the total number of recipients that have received a message since startup.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER  

exchispubMessagesSent 1.3.6.1.4.1.311.1.1.3.1.1.24.6
Messages Sent is the total number of messages sent to other storage providers via the message transfer agent (MTA) since startup.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER  

exchispubMessagesSubmitted 1.3.6.1.4.1.311.1.1.3.1.1.24.7
Messages Submitted is the total number of messages submitted by clients since startup.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER  

exchispubSingleInstanceRatio 1.3.6.1.4.1.311.1.1.3.1.1.24.8
Single Instance Ratio is the average number of references to each message in the public information store.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER  

exchispubMessagesDeliveredPerMin 1.3.6.1.4.1.311.1.1.3.1.1.24.10
Messages Delivered/min is the rate that messages are delivered to all recipients.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER  

exchispubMessageRecipientsDeliveredPerMin 1.3.6.1.4.1.311.1.1.3.1.1.24.11
Message Recipients Delivered/min is the rate that recipients receive messages.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER  

exchispubMessagesSentPerMin 1.3.6.1.4.1.311.1.1.3.1.1.24.12
Messages Sent/min is the rate that messages are sent to other storage providers via the message transfter agent (MTA).
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER  

exchispubMessageSubmittedPerMin 1.3.6.1.4.1.311.1.1.3.1.1.24.13
Messages Submitted/min is the rate that messages are submitted by clients.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER  

exchispubAverageTimeForDelivery 1.3.6.1.4.1.311.1.1.3.1.1.24.14
Average Time for Delivery is the average time between the submission of a message to the information store and submission to the messages transfer agent (MTA) for the last 10 messages.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER  

exchispubAverageTimeForLocalDelivery 1.3.6.1.4.1.311.1.1.3.1.1.24.15
Average Time for Local Delivery is the average time between the submission of a message to the information store and the delivery to all local recipients (recipients on the same server) for the last 10 messages.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER  

exchispubTotalSizeOfRecoverableItems 1.3.6.1.4.1.311.1.1.3.1.1.24.16
Total Size of Recoverable Items is the total size in kilobytes of items retained for Item Recovery
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER  

exchispubTotalCountOfRecoverableItems 1.3.6.1.4.1.311.1.1.3.1.1.24.17
Total Count of Recoverable Items is the total number of items retained for Item Recovery
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER  

exchispubReplicationMessagesSent 1.3.6.1.4.1.311.1.1.3.1.1.24.18
Replication Messages Sent is the total number of replication messages that have been sent to other servers since service startup.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER  

exchispubReplicationFolderTreeMessagesSent 1.3.6.1.4.1.311.1.1.3.1.1.24.19
Replication Folder Tree Messages Sent is the number of replication messages due to public folder hierarchy changes that have been sent to other servers since service startup.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER  

exchispubReplicationFolderChangesSent 1.3.6.1.4.1.311.1.1.3.1.1.24.20
Replication Folder Tree Messages Sent is the number of replication messages due to public folder hierarchy changes that have been sent to other servers since service startup.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER  

exchispubReplicationFolderDataMessagesSent 1.3.6.1.4.1.311.1.1.3.1.1.24.21
Replication Folder Data Message Messages sent is the number of replication messages due to changes to items in public folders that have been sent to other servers since service startup.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER  

exchispubReplicationMessageChangesSent 1.3.6.1.4.1.311.1.1.3.1.1.24.22
Replication Message Changes Sent is the number of changes to items in public folders that have been replicated to other servers since service startup.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER  

exchispubReplicationStatusMessagesSent 1.3.6.1.4.1.311.1.1.3.1.1.24.23
Replication Status Messages Sent is the number of replication status request or response messages that have been sent to other servers since service startup.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER  

exchispubReplicationBackfillRequestsSent 1.3.6.1.4.1.311.1.1.3.1.1.24.24
Replication Backfill Requests Sent is the number of backfill request replication messages that have been sent to other servers since service startup.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER  

exchispubReplicationBackfillDataMessagesSent 1.3.6.1.4.1.311.1.1.3.1.1.24.25
Replication Backfill Data Messages Sent is the number of replication messages sent in response to backfill requests from other servers since service startup.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER  

exchispubReplicationMessagesReceived 1.3.6.1.4.1.311.1.1.3.1.1.24.26
Replication Messages Received is the total number of replication messages received from other servers since service startup.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER  

exchispubReplicationFolderTreeMessagesReceived 1.3.6.1.4.1.311.1.1.3.1.1.24.27
Replication Folder Tree Messages Received is the number of replication messages due to public folder hierarchy changes that have been received from other servers since service startup.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER  

exchispubReplicationFolderChangesReceived 1.3.6.1.4.1.311.1.1.3.1.1.24.28
Replication Folder Changes Received is the number of folder changes that have been replicated from other servers since service startup.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER  

exchispubReplicationFolderDataMessagesReceived 1.3.6.1.4.1.311.1.1.3.1.1.24.29
Replication Folder Data Messages Received is the number of replication messages due to changes to items in public folders that have been received from other service since service startup.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER  

exchispubReplicationMessageChangesReceived 1.3.6.1.4.1.311.1.1.3.1.1.24.30
Replication Message Changes Received is the number of changes to items in public folders that have been received from other servers since service startup.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER  

exchispubReplicationStatusMessagesReceived 1.3.6.1.4.1.311.1.1.3.1.1.24.31
Status Messages Received is the number of replication status request or response messages that have been received from other servers since service startup.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER  

exchispubReplicationBackfillRequestsReceived 1.3.6.1.4.1.311.1.1.3.1.1.24.32
Replication Backfill Requests Received is the number of backfill request replication messages that have been received from other servers since service startup.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER  

exchispubReplicationBackfillDataMessagesReceived 1.3.6.1.4.1.311.1.1.3.1.1.24.33
Replication Backfill Data Messages Received is the number of replication messages received from other servers in response to backfill requests since service startup.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER  

exchispubReplicationReceiveQueueSize 1.3.6.1.4.1.311.1.1.3.1.1.24.34
Replication Receive Queue Size is the number of replication messages waiting to be processed.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER  

exchispubNumberOfMessagesExpiredFromPublicFolders 1.3.6.1.4.1.311.1.1.3.1.1.24.35
Number of messages expired from public folders
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER  

exchispubClientLogons 1.3.6.1.4.1.311.1.1.3.1.1.24.36
Client Logons is the number of clients (including system processes) currently logged on.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER  

exchispubActiveClientLogons 1.3.6.1.4.1.311.1.1.3.1.1.24.37
Active Client Logons is the number of clients that performed any action within the last ten minute time interval.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER  

exchispubPeakClientLogons 1.3.6.1.4.1.311.1.1.3.1.1.24.38
Peak Client Logons is the maximum number of concurrent client logons since service startup.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER  

exchispubFolderOpensPerSec 1.3.6.1.4.1.311.1.1.3.1.1.24.41
Folder opens/sec is the rate that requests to open folders are submitted to the information store.
Status: mandatory Access: read-only
OBJECT-TYPE    
  Counter  

exchispubMessageOpensPerSec 1.3.6.1.4.1.311.1.1.3.1.1.24.42
Message Opens/sec is the rate that requests to open messages are submitted to the information store.
Status: mandatory Access: read-only
OBJECT-TYPE    
  Counter  

mSExchangeIS-Private 1.3.6.1.4.1.311.1.1.3.1.1.25
OBJECT IDENTIFIER    

exchisprivSendQueueSize 1.3.6.1.4.1.311.1.1.3.1.1.25.1
Send Queue Size is the number of messages in the private information store's send queue.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER  

exchisprivReceiveQueueSize 1.3.6.1.4.1.311.1.1.3.1.1.25.2
Receive Queue Size is the number of messages in the private information store's receive queue.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER  

exchisprivCategorizationCount 1.3.6.1.4.1.311.1.1.3.1.1.25.3
Categorization Count is the number of categorizations that exist in the private information store. Categorizations are created when a user creates a filtered view or performs a search. When the information store must maintain an excessive number of categorizations, performance can be affected.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER  

exchisprivMessagesDelivered 1.3.6.1.4.1.311.1.1.3.1.1.25.4
Messages Delivered is the total number of messages delivered to all recipients since startup.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER  

exchisprivMessageRecipientsDelivered 1.3.6.1.4.1.311.1.1.3.1.1.25.5
Message Recipients Delivered is the total number of recipients that have received a message since startup.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER  

exchisprivMessagesSent 1.3.6.1.4.1.311.1.1.3.1.1.25.6
Messages Sent is the total number of messages sent to other storage providers via the message transfter agent (MTA) since startup.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER  

exchisprivMessagesSubmitted 1.3.6.1.4.1.311.1.1.3.1.1.25.7
Messages Submitted is the total number of messages submitted by clients since service startup.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER  

exchisprivSingleInstanceRatio 1.3.6.1.4.1.311.1.1.3.1.1.25.8
Single Instance Ratio is the average number of references to each message in the private information store.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER  

exchisprivMessagesDeliveredPerMin 1.3.6.1.4.1.311.1.1.3.1.1.25.10
Messages Delivered/min is the rate that messages are delivered to all recipients.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER  

exchisprivMessageRecipientsDeliveredPerMin 1.3.6.1.4.1.311.1.1.3.1.1.25.11
Message Recipients Delivered/min is the rate that recipients receive messages.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER  

exchisprivMessagesSentPerMin 1.3.6.1.4.1.311.1.1.3.1.1.25.12
Messages Sent/min is the rate that messages are sent to other storage providers via the message transfter agent (MTA).
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER  

exchisprivMessagesSubmittedPerMin 1.3.6.1.4.1.311.1.1.3.1.1.25.13
Messages Submitted/min is the rate that messages are submitted by clients.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER  

exchisprivAverageDeliveryTime 1.3.6.1.4.1.311.1.1.3.1.1.25.14
Average Delivery Time is the average time between the submission of a message to the information store and submission to the message transfer agent (MTA) for the last 10 messages.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER  

exchisprivAverageLocalDeliveryTime 1.3.6.1.4.1.311.1.1.3.1.1.25.15
Average Local Delivery Time is the average time between the submission of a message to the information store and the delivery to all local recipients (recipients on the same server) for the last 10 messages.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER  

exchisprivTotalSizeOfRecoverableItems 1.3.6.1.4.1.311.1.1.3.1.1.25.16
Total Size of Recoverable Items is the total size in kilobytes of items retained for Item Recovery
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER  

exchisprivTotalCountOfRecoverableItems 1.3.6.1.4.1.311.1.1.3.1.1.25.17
Total Count of Recoverable Items is the total number of items retained for Item Recovery
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER  

exchisprivClientLogons 1.3.6.1.4.1.311.1.1.3.1.1.25.36
Client Logons is the number of clients (including system processes) currently logged on.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER  

exchisprivActiveClientLogons 1.3.6.1.4.1.311.1.1.3.1.1.25.37
Active Client Logons is the number of clients that performed any action within the last ten minute time interval.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER  

exchisprivPeakClientLogons 1.3.6.1.4.1.311.1.1.3.1.1.25.38
Peak Client Logons is the maximum number of concurrent client logons since the service started.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER  

exchisprivLocalDeliveries 1.3.6.1.4.1.311.1.1.3.1.1.25.39
Total number of messages delivered locally
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER  

exchisprivLocalDeliveryRate 1.3.6.1.4.1.311.1.1.3.1.1.25.40
Rate at which messages are delivered locally
Status: mandatory Access: read-only
OBJECT-TYPE    
  Counter  

exchisprivFolderOpensPerSec 1.3.6.1.4.1.311.1.1.3.1.1.25.41
Folder Opens/sec is the rate that requests to open folders are submitted to the information store.
Status: mandatory Access: read-only
OBJECT-TYPE    
  Counter  

exchisprivMessageOpensPerSec 1.3.6.1.4.1.311.1.1.3.1.1.25.42
Message Opens/sec is the rate that requests to open messages are submitted to the information store.
Status: mandatory Access: read-only
OBJECT-TYPE    
  Counter  

mSExchangeDS 1.3.6.1.4.1.311.1.1.3.1.1.26
OBJECT IDENTIFIER    

exchdsAccessViolations 1.3.6.1.4.1.311.1.1.3.1.1.26.1
Access Violations is the number of times that directory service write operations were refused for security reasons.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER  

exchdsABBrowsesPerSec 1.3.6.1.4.1.311.1.1.3.1.1.26.2
AB Browses/sec is the rate at which Address Book clients perform browse operations.
Status: mandatory Access: read-only
OBJECT-TYPE    
  Counter  

exchdsABReadsPerSec 1.3.6.1.4.1.311.1.1.3.1.1.26.3
AB Reads/sec is the rate at which Address Book clients perform read operations.
Status: mandatory Access: read-only
OBJECT-TYPE    
  Counter  

exchdsExDSReadsPerSec 1.3.6.1.4.1.311.1.1.3.1.1.26.4
ExDS Reads/sec is the rate at which Extended Directory Service clients perform read operations.
Status: mandatory Access: read-only
OBJECT-TYPE    
  Counter  

exchdsReplicationUpdatesPerSec 1.3.6.1.4.1.311.1.1.3.1.1.26.5
Replication Updates/sec is the rate at which replication updates are applied by the local directory service. This indicates how much replication activity is occuring on the server.
Status: mandatory Access: read-only
OBJECT-TYPE    
  Counter  

exchdsThreadsInUse 1.3.6.1.4.1.311.1.1.3.1.1.26.6
Threads in Use is the current number of threads in use by the directory service (different than the number of threads in the directory service process). Threads in Use is the number of RPC-generated threads currently in API calls and can be used to indicate whether additional processors could be of benefit.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER  

exchdsABWritesPerSec 1.3.6.1.4.1.311.1.1.3.1.1.26.7
AB Writes/sec is the rate at which Address Book clients perform write operations.
Status: mandatory Access: read-only
OBJECT-TYPE    
  Counter  

exchdsExDSWritesPerSec 1.3.6.1.4.1.311.1.1.3.1.1.26.8
ExDS Writes/sec is the rate at which Extended Directory Service clients perform write operations.
Status: mandatory Access: read-only
OBJECT-TYPE    
  Counter  

exchdsExDSClientSessions 1.3.6.1.4.1.311.1.1.3.1.1.26.9
ExDS Client Sessions is the number of connected Extended Directory Service client sessions. This indicates the number of connections from other Microsoft Exchange services and the Microsoft Exchange Administrator program.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER  

exchdsABClientSessions 1.3.6.1.4.1.311.1.1.3.1.1.26.10
AB Client Sessions is the number of connected Address Book client sessions.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER  

exchdsPendingReplicationSynchronizations 1.3.6.1.4.1.311.1.1.3.1.1.26.11
Pending Replication Synchronizations is the number of directory synchronizations that are queued for this server but not yet processed.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER  

exchdsRemainingReplicationUpdates 1.3.6.1.4.1.311.1.1.3.1.1.26.12
Remaining Replication Updates is the number of object modifications received in the current directory replication update packet that have not yet been applied to the local server.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER  

exchdsObjectsReplicatedOutPerSec 1.3.6.1.4.1.311.1.1.3.1.1.26.13
This is the number of objects replicated out per second from this machine to other Directory Servers.
Status: mandatory Access: read-only
OBJECT-TYPE    
  Counter  

exchdsAddressBookViewReadsPerSec 1.3.6.1.4.1.311.1.1.3.1.1.26.14
Number of directory objects read per second by the View Consistency Checker.
Status: mandatory Access: read-only
OBJECT-TYPE    
  Counter  

exchdsAddressBookViewWritesPerSec 1.3.6.1.4.1.311.1.1.3.1.1.26.15
Number of Address Book View containers created per second by the View Consistency Checker.
Status: mandatory Access: read-only
OBJECT-TYPE    
  Counter  

exchdsAddressBookViewModifiesPerSec 1.3.6.1.4.1.311.1.1.3.1.1.26.16
Number of directory objects modified per second by the View Consistency Checker.
Status: mandatory Access: read-only
OBJECT-TYPE    
  Counter  

exchdsLDAPSearches 1.3.6.1.4.1.311.1.1.3.1.1.26.17
Total number of LDAP searches performed since the DSA started.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER  

exchdsLDAPSearchesPerSec 1.3.6.1.4.1.311.1.1.3.1.1.26.18
LDAP Searches/sec is the rate at which LDAP clients perform search operations.
Status: mandatory Access: read-only
OBJECT-TYPE    
  Counter  

web-Proxy-Server-Service 1.3.6.1.4.1.311.1.1.3.1.1.27
OBJECT IDENTIFIER    

webproxysrvrUpstreamBytesSentPerSec 1.3.6.1.4.1.311.1.1.3.1.1.27.1
Upstream Bytes Sent/sec is the rate at which data bytes are sent by the Web Proxy Server to remote servers on the Internet or to a chained Web Proxy Server.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER  

webproxysrvrUpstreamBytesReceivedPerSec 1.3.6.1.4.1.311.1.1.3.1.1.27.2
Upstream Bytes Received/sec is the rate at which data bytes are received by the Web Proxy Server from remote servers on the Internet or from a chained Web Proxy Server in response to requests from this Proxy.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER  

webproxysrvrUpstreamBytesTotalPerSec 1.3.6.1.4.1.311.1.1.3.1.1.27.3
Upstream Bytes Total/sec is the sum of Inet Bytes Sent/sec and Bytes Received/sec. This is the total rate for all bytes transferred between the Proxy Server and remote servers on the Internet or a chained Web Proxy Server.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER  

webproxysrvrClientBytesSentPerSec 1.3.6.1.4.1.311.1.1.3.1.1.27.4
Client Bytes Sent/sec is the rate at which data bytes are sent by the Web Proxy Server to Web Proxy clients.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER  

webproxysrvrClientBytesReceivedPerSec 1.3.6.1.4.1.311.1.1.3.1.1.27.5
Client Bytes Received/sec is the rate at which data bytes are received by the Web Proxy Server from Web Proxy clients.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER  

webproxysrvrClientBytesTotalPerSec 1.3.6.1.4.1.311.1.1.3.1.1.27.6
Client Bytes Total/sec is the sum of Client Bytes Sent/sec and Bytes Received/sec. This is the total rate for all bytes transferred between the Web Proxy Server and Web Proxy clients.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER  

webproxysrvrSSLClientBytesSentPerSec 1.3.6.1.4.1.311.1.1.3.1.1.27.7
SSL Client Bytes Sent/sec is the rate at which Secure Sockets Layer (SSL) data bytes are sent by the Web Proxy Server to secured Web Proxy clients.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER  

webproxysrvrSSLClientBytesReceivedPerSec 1.3.6.1.4.1.311.1.1.3.1.1.27.8
SSL Client Bytes Received/sec is the rate at which Secure Sockets Layer (SSL) data bytes are received by the Web Proxy Server from secured Web Proxy clients.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER  

webproxysrvrSSLClientBytesTotalPerSec 1.3.6.1.4.1.311.1.1.3.1.1.27.9
SSL Client Bytes Total/sec is the sum of SSL Client Bytes Sent/sec and Bytes Received/sec. This is the total rate for all bytes transferred between the Web Proxy Server and secured Web Proxy clients.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER  

webproxysrvrSocksClientBytesSentPerSec 1.3.6.1.4.1.311.1.1.3.1.1.27.10
Socks Client Bytes Sent/sec is the rate at which data is transferred by the Web Proxy Server from Socks clients to connected servers.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER  

webproxysrvrSocksClientBytesReceivedPerSec 1.3.6.1.4.1.311.1.1.3.1.1.27.11
Socks Client Bytes Received/sec is the rate at which data is transferred by the Web Proxy Server from connected servers to Socks clients.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER  

webproxysrvrSocksClientBytesTotalPerSec 1.3.6.1.4.1.311.1.1.3.1.1.27.12
Socks Client Bytes Total/sec is the sum of Socks Client Bytes Sent/sec and Bytes Received/sec. This is the total rate for all bytes transferred between the Web Proxy Server and Socks clients.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER  

webproxysrvrCurrentUsers 1.3.6.1.4.1.311.1.1.3.1.1.27.13
Current Users is the number of users currently connected to the Web Proxy Server.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER  

webproxysrvrTotalUsers 1.3.6.1.4.1.311.1.1.3.1.1.27.14
Total Users is the total number of users that have ever connected to the Web Proxy Server.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER  

webproxysrvrMaximumUsers 1.3.6.1.4.1.311.1.1.3.1.1.27.15
Maximum Users is the maximum number of users that have connected to the Web Proxy Server simultaneously.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER  

webproxysrvrFtpRequests 1.3.6.1.4.1.311.1.1.3.1.1.27.16
Ftp Requests is the number of Ftp requests that have been made to the Web Proxy Server.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER  

webproxysrvrGopherRequests 1.3.6.1.4.1.311.1.1.3.1.1.27.17
Gopher Requests is the number of Gopher requests that have been made to the Web Proxy Server.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER  

webproxysrvrHttpRequests 1.3.6.1.4.1.311.1.1.3.1.1.27.18
Http Requests is the number of Http requests that have been made to the Web Proxy Server.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER  

webproxysrvrTotalRequests 1.3.6.1.4.1.311.1.1.3.1.1.27.19
Total Requests is the total number of requests that have ever been made to the Web Proxy Server.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER  

webproxysrvrTotalSuccessfulRequests 1.3.6.1.4.1.311.1.1.3.1.1.27.20
Total Successful Requests is the total number of requests that have been successfully processed by the Web Proxy Server.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER  

webproxysrvrTotalFailingRequests 1.3.6.1.4.1.311.1.1.3.1.1.27.21
Total Failing Requests is the total number of requests that have failed to be processed by the Web Proxy Server due to errors. Errors can be the result of the Web Proxy Server failing to locate a requested server URL on the Internet or because the client failed to be authorized access to the requested URL.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER  

webproxysrvrTotalCacheFetches 1.3.6.1.4.1.311.1.1.3.1.1.27.22
Total Cache Fetches is the total number of requests that have been served by using cached data from the Web Proxy Server cache.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER  

webproxysrvrTotalUpstreamFetches 1.3.6.1.4.1.311.1.1.3.1.1.27.23
Total Upstream Fetches is the total number of requests that have been served by using data retrieved from servers on the Internet or from a chained Web Proxy Server.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER  

webproxysrvrCacheHitRatioPercent 1.3.6.1.4.1.311.1.1.3.1.1.27.24
Cache Hit Ratio is the percentage of requests that have been served using cached data out of the total number of requests to the Web Proxy Server.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER  

webproxysrvrSitesDenied 1.3.6.1.4.1.311.1.1.3.1.1.27.25
Sites Denied is the total number of Internet sites to which the Web Proxy Server has denied access.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER  

webproxysrvrSitesGranted 1.3.6.1.4.1.311.1.1.3.1.1.27.26
Sites Granted is the total number of Internet sites to which the Web Proxy Server has granted access.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER  

webproxysrvrDNSCacheEntries 1.3.6.1.4.1.311.1.1.3.1.1.27.27
DNS Cache Entries is the current number of DNS domain name entries cached by the Web Proxy Server.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER  

webproxysrvrDNSRetrievals 1.3.6.1.4.1.311.1.1.3.1.1.27.28
DNS Retrievals is the total number of DNS domain names that have been retrieved by the Web Proxy Server.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER  

webproxysrvrDNSCacheFlushes 1.3.6.1.4.1.311.1.1.3.1.1.27.29
DNS Cache Flushes is the total number of times that the DNS domain name cache has been flushed or cleared by the Web Proxy Server.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER  

webproxysrvrDNSCacheHits 1.3.6.1.4.1.311.1.1.3.1.1.27.30
DNS Cache Hits is the total number of times a DNS domain name was found within the DNS Cache.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER  

webproxysrvrDNSCacheHitsPercent 1.3.6.1.4.1.311.1.1.3.1.1.27.31
DNS Cache Hits % is the percentage of DNS domain names served from the Web Proxy Server cache, from the total of all DNS entries that have been retrieved by the Web Proxy Server.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER  

webproxysrvrHTTPSSessions 1.3.6.1.4.1.311.1.1.3.1.1.27.33
HTTPS sessions is the total number of HTTP-secured sessions serviced by the Secure Sockets Layer (SSL) tunnel.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER  

webproxysrvrSNEWSSessions 1.3.6.1.4.1.311.1.1.3.1.1.27.34
SNEWS sessions is the total number of SNEWS sessions serviced by the Secure Sockets Layer (SSL) tunnel.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER  

webproxysrvrUnknownSSLSessions 1.3.6.1.4.1.311.1.1.3.1.1.27.35
Unknown SSL sessions is the total number of unknown Secure Sockets Layer (SSL) sessions serviced by the SSL tunnel.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER  

webproxysrvrTotalSSLSessions 1.3.6.1.4.1.311.1.1.3.1.1.27.36
Total SSL sessions is the total number of Secure Sockets Layer (SSL) sessions serviced by the SSL tunnel.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER  

webproxysrvrSocksSessions 1.3.6.1.4.1.311.1.1.3.1.1.27.37
Socks sessions is the current number of active sessions between Socks clients and connected servers serviced by the Web Proxy Server.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER  

webproxysrvrTotalSocksSessions 1.3.6.1.4.1.311.1.1.3.1.1.27.38
Total Socks Sessions is the accumulative number of Socks sessions serviced by the Web Proxy Server.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER  

webproxysrvrTotalSuccessfulSocksSessions 1.3.6.1.4.1.311.1.1.3.1.1.27.39
Total Successful Socks Sessions is the accumulative number of Socks requests that were successfully serviced by the Web Proxy Server.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER  

webproxysrvrTotalFailedSocksSessions 1.3.6.1.4.1.311.1.1.3.1.1.27.40
Total Failed Socks Sessions is the accumulative number of Socks requests that were were not serviced by the Web Proxy Server because the client did not have the access rights to satisfy the request, or an initial protocol error.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER  

webproxysrvrThreadPoolSize 1.3.6.1.4.1.311.1.1.3.1.1.27.41
Thread Pool Size is the number of threads in the thread pool.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER  

webproxysrvrThreadPoolFailures 1.3.6.1.4.1.311.1.1.3.1.1.27.42
Thread Pool Failures is the number of requests rejected because the thread pool was overcommitted.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER  

webproxysrvrSSLSessionsScavenged 1.3.6.1.4.1.311.1.1.3.1.1.27.43
SSL sessions scavenged is the number of Secure Sockets Layer (SSL) sessions closed because of idle timeout and excessive SSL demand.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER  

webproxysrvrThreadPoolActiveSessions 1.3.6.1.4.1.311.1.1.3.1.1.27.44
Thread Pool active sessions is the number of sessions being actively serviced by thread pool threads.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER  

webproxysrvrArrayBytesSentPerSec 1.3.6.1.4.1.311.1.1.3.1.1.27.45
Array Bytes Sent/sec is the rate at which data bytes are sent by the Web Proxy Server to other proxies within the same array.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER  

webproxysrvrArrayBytesReceivedPerSec 1.3.6.1.4.1.311.1.1.3.1.1.27.46
Array Bytes Received/sec is the rate at which data bytes are received by the Web Proxy Server from other Proxies within the same array in response to requests from this Proxy.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER  

webproxysrvrArrayBytesTotalPerSec 1.3.6.1.4.1.311.1.1.3.1.1.27.47
Array Bytes Total/sec is the sum of Array Bytes Sent/sec and Bytes Received/sec. This is the total rate for all bytes transferred between the Proxy Server and other members of the same array.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER  

webproxysrvrTotalArrayFetches 1.3.6.1.4.1.311.1.1.3.1.1.27.50
Total Array Fetches is the total number of requests that have been served by requesting the data from another Web Proxy Server within this array.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER  

webproxysrvrReverseBytesSentPerSec 1.3.6.1.4.1.311.1.1.3.1.1.27.51
Reverse Bytes Sent/sec is the rate at which data bytes are sent by the Web Proxy Server to web publishing servers in response to Reverse Proxy requests.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER  

webproxysrvrReverseBytesReceivedPerSec 1.3.6.1.4.1.311.1.1.3.1.1.27.52
Reverse Bytes Received/sec is the rate at which data bytes are received by the Web Proxy Server from web publishing serverse in response Reverse Proxy requests.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER  

webproxysrvrReverseBytesTotalPerSec 1.3.6.1.4.1.311.1.1.3.1.1.27.53
Reverse Bytes Total/sec is the sum of Reverse Bytes Sent/sec and Bytes Received/sec. This is the total rate for all bytes transferred between the Proxy Server and web publishing servers in response to Reverse Proxy requests.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER  

webproxysrvrTotalReverseFetches 1.3.6.1.4.1.311.1.1.3.1.1.27.54
Total Reverse Fetches is the total number of Reverse Proxy requests that have been served by requesting the data from web publishing servers.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER  

webproxysrvrRequestsPerSec 1.3.6.1.4.1.311.1.1.3.1.1.27.55
Requests/sec is the rate of incoming requests that have been made to the Web Proxy Server.
Status: mandatory Access: read-only
OBJECT-TYPE    
  Counter  

webproxysrvrFailingRequestsPerSec 1.3.6.1.4.1.311.1.1.3.1.1.27.56
Failing Requests/sec is the rate of requests that have completed with some type of error.
Status: mandatory Access: read-only
OBJECT-TYPE    
  Counter  

winSock-Proxy-Server 1.3.6.1.4.1.311.1.1.3.1.1.28
OBJECT IDENTIFIER    

winsockproxysrvrSuccessfulDNSResolutions 1.3.6.1.4.1.311.1.1.3.1.1.28.1
Number of 'gethostbyname' and 'gethostbyaddr' API calls successfully returned. These are calls used to resolve host DNS domain names and IP addresses for WinSock Proxy connections.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER  

winsockproxysrvrFailedDNSResolutions 1.3.6.1.4.1.311.1.1.3.1.1.28.2
Number of 'gethostbyname' and 'gethostbyaddr' API calls that have failed. These are calls used to resolve host DNS domain names and IP addresses for WinSock Proxy connections.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER  

winsockproxysrvrPendingDNSResolutions 1.3.6.1.4.1.311.1.1.3.1.1.28.3
Number of 'gethostbyname' and 'gethostbyaddr' API calls pending resolution. These are calls used to resolve host DNS domain names and IP addresses for WinSock Proxy connections.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER  

winsockproxysrvrActiveSessions 1.3.6.1.4.1.311.1.1.3.1.1.28.4
The number of active sessions for WinSock Proxy Server.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER  

winsockproxysrvrActiveTCPConnections 1.3.6.1.4.1.311.1.1.3.1.1.28.5
The total number of active TCP connections currently passing data. Connections pending or not yet established are counted elsewhere.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER  

winsockproxysrvrActiveUDPConnections 1.3.6.1.4.1.311.1.1.3.1.1.28.6
Total number of active UDP connections.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER  

winsockproxysrvrConnectingTCPConnections 1.3.6.1.4.1.311.1.1.3.1.1.28.7
Total number of TCP connections pending. These are connections awaiting completion between WinSock Proxy Server and remote computers.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER  

winsockproxysrvrBack-ConnectingTCPConnections 1.3.6.1.4.1.311.1.1.3.1.1.28.8
Total number of TCP connections awaiting an inbound 'connect' call to complete. These are connections placed by WinSock Proxy (WSP) to a client after WSP accepts a connection from the Internet on a listening socket.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER  

winsockproxysrvrAcceptingTCPConnections 1.3.6.1.4.1.311.1.1.3.1.1.28.9
Number of connection objects that wait for TCP connection from WinSock Proxy clients.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER  

winsockproxysrvrListeningTCPConnections 1.3.6.1.4.1.311.1.1.3.1.1.28.10
Number of connection objects that wait for TCP connections from remote Internet computers.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER  

winsockproxysrvrWorkerThreads 1.3.6.1.4.1.311.1.1.3.1.1.28.11
The number of WinSock Proxy worker threads that are currently alive.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER  

winsockproxysrvrAvailableWorkerThreads 1.3.6.1.4.1.311.1.1.3.1.1.28.12
The number of WinSock Proxy worker threads that are available (waiting in completion port queue).
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER  

winsockproxysrvrBytesReadPerSec 1.3.6.1.4.1.311.1.1.3.1.1.28.13
Number of bytes read by the data-pump per second.
Status: mandatory Access: read-only
OBJECT-TYPE    
  Counter  

winsockproxysrvrBytesWrittenPerSec 1.3.6.1.4.1.311.1.1.3.1.1.28.14
Number of bytes written by data-pump per second.
Status: mandatory Access: read-only
OBJECT-TYPE    
  Counter  

winsockproxysrvrNon-connectedUDPMappings 1.3.6.1.4.1.311.1.1.3.1.1.28.15
The number of mappings available for UDP connections.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER  

winsockproxysrvrDNSCacheEntries 1.3.6.1.4.1.311.1.1.3.1.1.28.16
DNS Cache Entries is the current number of DNS domain name entries cached by the Web Proxy Server.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER  

winsockproxysrvrDNSCacheHits 1.3.6.1.4.1.311.1.1.3.1.1.28.17
DNS Cache Hits is the total number of times a DNS domain name was found within the DNS Cache.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER  

winsockproxysrvrDNSCacheFlushes 1.3.6.1.4.1.311.1.1.3.1.1.28.18
DNS Cache Flushes is the total number of times that the DNS domain name cache has been flushed or cleared by the Web Proxy Server.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER  

winsockproxysrvrDNSRetrievals 1.3.6.1.4.1.311.1.1.3.1.1.28.19
DNS Retrievals is the total number of DNS domain names that have been retrieved by the Web Proxy Server.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER  

winsockproxysrvrDNSCacheHitsPercent 1.3.6.1.4.1.311.1.1.3.1.1.28.20
DNS Cache Hits % is the percentage of DNS domain names served from the Web Proxy Server cache, from the total of all DNS entries that have been retrieved by the Web Proxy Server.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER  

web-Proxy-Server-Cache 1.3.6.1.4.1.311.1.1.3.1.1.29
OBJECT IDENTIFIER    

webproxysrvrcacheURLsInCache 1.3.6.1.4.1.311.1.1.3.1.1.29.1
URLs in Cache is the current number of URLs in the URL Cache.
Status: mandatory Access: read-only
OBJECT-TYPE    
  Counter  

webproxysrvrcacheBytesInCache 1.3.6.1.4.1.311.1.1.3.1.1.29.2
Bytes in Cache is the total number of bytes currently contained in the URL Cache.
Status: mandatory Access: read-only
OBJECT-TYPE    
  Counter  

webproxysrvrcacheTotalBytesCached 1.3.6.1.4.1.311.1.1.3.1.1.29.3
Total Bytes Cached is the cumulative number of bytes that have been placed into the URL Cache.
Status: mandatory Access: read-only
OBJECT-TYPE    
  Counter  

webproxysrvrcacheTotalBytesRetrieved 1.3.6.1.4.1.311.1.1.3.1.1.29.4
Total Bytes Retrieved is the cumulative number of bytes that have been retrieved from the URL Cache.
Status: mandatory Access: read-only
OBJECT-TYPE    
  Counter  

webproxysrvrcacheTotalURLsCached 1.3.6.1.4.1.311.1.1.3.1.1.29.5
Total URLs Cached is the cumulative number of URLs that have been stored into the URL Cache.
Status: mandatory Access: read-only
OBJECT-TYPE    
  Counter  

webproxysrvrcacheTotalURLsRetrieved 1.3.6.1.4.1.311.1.1.3.1.1.29.6
Total URLs Retrieved is the cumulative number of URLs that have been retrieved from the URL Cache.
Status: mandatory Access: read-only
OBJECT-TYPE    
  Counter  

webproxysrvrcacheMaxBytesCached 1.3.6.1.4.1.311.1.1.3.1.1.29.7
Max Bytes Cached is the maximum number of bytes that have been stored in the URL Cache.
Status: mandatory Access: read-only
OBJECT-TYPE    
  Counter  

webproxysrvrcacheMaxURLsCached 1.3.6.1.4.1.311.1.1.3.1.1.29.8
Max URLs Cached is the maximum number of URLs that have been stored in the URL Cache.
Status: mandatory Access: read-only
OBJECT-TYPE    
  Counter  

webproxysrvrcacheTotalActivelyRefreshedURLs 1.3.6.1.4.1.311.1.1.3.1.1.29.9
Total Actively Refreshed URLs is the cumulative number of popular URLs in the URL cache that have been preemptively refreshed from the Internet.
Status: mandatory Access: read-only
OBJECT-TYPE    
  Counter  

webproxysrvrcacheTotalBytesActivelyRefreshed 1.3.6.1.4.1.311.1.1.3.1.1.29.10
Total Bytes Actively Refreshed is the total of bytes that have been retrieved from the Internet to preemptively refresh popular URLs in the URL cache.
Status: mandatory Access: read-only
OBJECT-TYPE    
  Counter  

webproxysrvrcacheURLRetrieveRate 1.3.6.1.4.1.311.1.1.3.1.1.29.11
URL Retrieve Rate is the rate at which URLs are retrieved from the URL cache.
Status: mandatory Access: read-only
OBJECT-TYPE    
  Counter  

webproxysrvrcacheBytesRetrievedRate 1.3.6.1.4.1.311.1.1.3.1.1.29.12
Bytes Retrieved Rate is the rate at which bytes of data are retrieved from the URL cache.
Status: mandatory Access: read-only
OBJECT-TYPE    
  Counter  

webproxysrvrcacheURLCommitRate 1.3.6.1.4.1.311.1.1.3.1.1.29.13
URL Commit Rate is the rate at which URLs are commited to the URL cache.
Status: mandatory Access: read-only
OBJECT-TYPE    
  Counter  

webproxysrvrcacheBytesCommitedRate 1.3.6.1.4.1.311.1.1.3.1.1.29.14
Bytes Commited Rate is the rate at which bytes of data are commited to the URL cache.
Status: mandatory Access: read-only
OBJECT-TYPE    
  Counter  

webproxysrvrcacheActiveURLRefreshRate 1.3.6.1.4.1.311.1.1.3.1.1.29.15
Active URL Refresh Rate is the rate at which popular URLs in the URL cache are preemptively refreshed from the Internet.
Status: mandatory Access: read-only
OBJECT-TYPE    
  Counter  

webproxysrvrcacheActiveRefreshBytesRate 1.3.6.1.4.1.311.1.1.3.1.1.29.16
Active Refresh Bytes Rate is the rate at which bytes of data are retrieved from the Internet to preemptively refresh popular URLs in the URL cache.
Status: mandatory Access: read-only
OBJECT-TYPE    
  Counter  

telephony 1.3.6.1.4.1.311.1.1.3.1.1.30
OBJECT IDENTIFIER    

telephonyLines 1.3.6.1.4.1.311.1.1.3.1.1.30.1
The number of telephone lines serviced by this computer.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER  

telephonyTelephoneDevices 1.3.6.1.4.1.311.1.1.3.1.1.30.2
The number of telephone devices serviced by this computer.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER  

telephonyActiveLines 1.3.6.1.4.1.311.1.1.3.1.1.30.3
The number of telephone lines serviced by this computer that are currently active.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER  

telephonyActiveTelephones 1.3.6.1.4.1.311.1.1.3.1.1.30.4
The number of telephone devices that are currently being monitored.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER  

telephonyOutgoingCallsPerSec 1.3.6.1.4.1.311.1.1.3.1.1.30.5
The rate of outgoing calls made by this computer.
Status: mandatory Access: read-only
OBJECT-TYPE    
  Counter  

telephonyIncomingCallsPerSec 1.3.6.1.4.1.311.1.1.3.1.1.30.6
The rate of incoming calls answered by this computer.
Status: mandatory Access: read-only
OBJECT-TYPE    
  Counter  

telephonyClientApps 1.3.6.1.4.1.311.1.1.3.1.1.30.7
The number of applications that are currently using telephony services.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER  

telephonyCurrentOutgoingCalls 1.3.6.1.4.1.311.1.1.3.1.1.30.8
Current outgoing calls being serviced by this computer.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER  

telephonyCurrentIncomingCalls 1.3.6.1.4.1.311.1.1.3.1.1.30.9
Current incoming calls being serviced by this computer.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER  

rasportrAS-PortTable 1.3.6.1.4.1.311.1.1.3.1.1.31
A table containing performance information for instances of 'rAS-Port' objects.
Status: mandatory Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    RasportrAS-PortEntry

rasportrAS-PortEntry 1.3.6.1.4.1.311.1.1.3.1.1.31.1
Performance information for one particular instance of 'rAS-Port' object.
Status: mandatory Access: not-accessible
OBJECT-TYPE    
  RasportrAS-PortEntry  

rasportrAS-PortIndex 1.3.6.1.4.1.311.1.1.3.1.1.31.1.1
Index.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER  

rasportrAS-PortInstance 1.3.6.1.4.1.311.1.1.3.1.1.31.1.2
Instance name.
Status: mandatory Access: read-only
OBJECT-TYPE    
  DisplayString  

rasportBytesTransmitted 1.3.6.1.4.1.311.1.1.3.1.1.31.1.3
The number of bytes transmitted total for this connection.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER  

rasportBytesReceived 1.3.6.1.4.1.311.1.1.3.1.1.31.1.4
The number of bytes received total for this connection.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER  

rasportFramesTransmitted 1.3.6.1.4.1.311.1.1.3.1.1.31.1.5
The number of data frames transmitted total for this connection.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER  

rasportFramesReceived 1.3.6.1.4.1.311.1.1.3.1.1.31.1.6
The number of data frames received total for this connection.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER  

rasportPercentCompressionOut 1.3.6.1.4.1.311.1.1.3.1.1.31.1.7
The compression ratio for bytes being transmitted.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER  

rasportPercentCompressionIn 1.3.6.1.4.1.311.1.1.3.1.1.31.1.8
The compression ratio for bytes being received.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER  

rasportCRCErrors 1.3.6.1.4.1.311.1.1.3.1.1.31.1.9
The total number of CRC Errors for this connection. CRC Errors occur when the frame received contains erroneous data.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER  

rasportTimeoutErrors 1.3.6.1.4.1.311.1.1.3.1.1.31.1.10
The total number of Timeout Errors for this connection. Timeout Errors occur when an expected is not received in time.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER  

rasportSerialOverrunErrors 1.3.6.1.4.1.311.1.1.3.1.1.31.1.11
The total number of Serial Overrun Errors for this connection. Serial Overrun Errors occur when the hardware cannot handle the rate at which data is received.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER  

rasportAlignmentErrors 1.3.6.1.4.1.311.1.1.3.1.1.31.1.12
The total number of Alignment Errors for this connection. Alignment Errors occur when a byte received is different from the byte expected.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER  

rasportBufferOverrunErrors 1.3.6.1.4.1.311.1.1.3.1.1.31.1.13
The total number of Buffer Overrun Errors for this connection. Buffer Overrun Errors when the software cannot handle the rate at which data is received.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER  

rasportTotalErrors 1.3.6.1.4.1.311.1.1.3.1.1.31.1.14
The total number of CRC, Timeout, Serial Overrun, Alignment, and Buffer Overrun Errors for this connection.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER  

rasportBytesTransmittedPerSec 1.3.6.1.4.1.311.1.1.3.1.1.31.1.15
The number of bytes transmitted per second.
Status: mandatory Access: read-only
OBJECT-TYPE    
  Counter  

rasportBytesReceivedPerSec 1.3.6.1.4.1.311.1.1.3.1.1.31.1.16
The number of bytes received per second.
Status: mandatory Access: read-only
OBJECT-TYPE    
  Counter  

rasportFramesTransmittedPerSec 1.3.6.1.4.1.311.1.1.3.1.1.31.1.17
The number of frames transmitted per second.
Status: mandatory Access: read-only
OBJECT-TYPE    
  Counter  

rasportFramesReceivedPerSec 1.3.6.1.4.1.311.1.1.3.1.1.31.1.18
The number of frames received per second.
Status: mandatory Access: read-only
OBJECT-TYPE    
  Counter  

rasportTotalErrorsPerSec 1.3.6.1.4.1.311.1.1.3.1.1.31.1.19
The total number of CRC, Timeout, Serial Overrun, Alignment, and Buffer Overrun Errors per second.
Status: mandatory Access: read-only
OBJECT-TYPE    
  Counter  





nwnetbiosDatagramsPerSec 1.3.6.1.4.1.311.1.1.3.1.1.32.1.3
Datagrams/sec is the rate that datagrams are processed by the computer. This counter displays the sum of datagrams sent and datagrams received. A datagram is a connectionless packet whose delivery to a remote is not guaranteed.
Status: mandatory Access: read-only
OBJECT-TYPE    
  Counter  

nwnetbiosDatagramBytesPerSec 1.3.6.1.4.1.311.1.1.3.1.1.32.1.4
Datagram Bytes/sec is the rate that datagram bytes are processed by the computer. This counter is the sum of datagram bytes that are sent as well as received. A datagram is a connectionless packet whose delivery to a remote is not guaranteed.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER  

nwnetbiosPacketsPerSec 1.3.6.1.4.1.311.1.1.3.1.1.32.1.5
Packets/sec is the rate that packets are processed by the computer. This count is the sum of Packets Sent and Packets Received per second. This counter includes all packets processed: control as well as data packets.
Status: mandatory Access: read-only
OBJECT-TYPE    
  Counter  

nwnetbiosFramesPerSec 1.3.6.1.4.1.311.1.1.3.1.1.32.1.6
Frames/sec is the rate that data frames (or packets) are processed by the computer. This counter is the sum of data frames sent and data frames received. This counter only counts those frames (packets) that carry data.
Status: mandatory Access: read-only
OBJECT-TYPE    
  Counter  

nwnetbiosFrameBytesPerSec 1.3.6.1.4.1.311.1.1.3.1.1.32.1.7
Frame Bytes/sec is the rate that data bytes are processed by the computer. This counter is the sum of data frame bytes sent and received. This counter only counts the byte in frames (packets) that carry data.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER  

nwnetbiosBytesTotalPerSec 1.3.6.1.4.1.311.1.1.3.1.1.32.1.8
Bytes Total/sec is the sum of Frame Bytes/sec and Datagram Bytes/sec. This is the total rate of bytes sent to or received from the network by the protocol, but only counts the bytes in frames (i.e., packets) which carry data.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER  

nwnetbiosConnectionsOpen 1.3.6.1.4.1.311.1.1.3.1.1.32.1.9
Connections Open is the number of connections currently open for this protocol. This counter shows the current count only and does not accumulate over time.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER  

nwnetbiosConnectionsNoRetries 1.3.6.1.4.1.311.1.1.3.1.1.32.1.10
Connections No Retries is the total count of connections that were successfully made on the first try. This number is an accumulator and shows a running total.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER  

nwnetbiosConnectionsWithRetries 1.3.6.1.4.1.311.1.1.3.1.1.32.1.11
Connections With Retries is the total count of connections that were made after retrying the attempt. A retry occurs when the first connection attempt failed. This number is an accumulator and shows a running total.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER  

nwnetbiosDisconnectsLocal 1.3.6.1.4.1.311.1.1.3.1.1.32.1.12
Disconnects Local is the number of session disconnections that were initiated by the local computer. This number is an accumulator and shows a running total.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER  

nwnetbiosDisconnectsRemote 1.3.6.1.4.1.311.1.1.3.1.1.32.1.13
Disconnects Remote is the number of session disconnections that were initiated by the remote computer. This number is an accumulator and shows a running total.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER  


nwnetbiosFailuresAdapter 1.3.6.1.4.1.311.1.1.3.1.1.32.1.15
Failures Adapter is the number of connections that were dropped due to an adapter failure. This number is an accumulator and shows a running total.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER  

nwnetbiosConnectionSessionTimeouts 1.3.6.1.4.1.311.1.1.3.1.1.32.1.16
Connection Session Timeouts is the number of connections that were dropped due to a session timeout. This number is an accumulator and shows a running total.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER  

nwnetbiosConnectionsCanceled 1.3.6.1.4.1.311.1.1.3.1.1.32.1.17
Connections Canceled is the number of connections that were canceled. This number is an accumulator and shows a running total.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER  

nwnetbiosFailuresResourceRemote 1.3.6.1.4.1.311.1.1.3.1.1.32.1.18
Failures Resource Remote is the number of connections that failed because of resource problems or shortages on the remote computer. This number is an accumulator and shows a running total.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER  

nwnetbiosFailuresResourceLocal 1.3.6.1.4.1.311.1.1.3.1.1.32.1.19
Failures Resource Local is the number of connections that failed because of resource problems or shortages on the local computer. This number is an accumulator and shows a running total.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER  

nwnetbiosFailuresNotFound 1.3.6.1.4.1.311.1.1.3.1.1.32.1.20
Failures Not Found is the number of connection attempts that failed because the remote computer could not be found. This number is an accumulator and shows a running total.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER  

nwnetbiosFailuresNoListen 1.3.6.1.4.1.311.1.1.3.1.1.32.1.21
Failures No Listen is the number of connections that were rejected because the remote computer was not listening for connection requests.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER  

nwnetbiosDatagramsSentPerSec 1.3.6.1.4.1.311.1.1.3.1.1.32.1.22
Datagrams Sent/sec is the rate that datagrams are sent from the computer. A datagram is a connectionless packet whose delivery to a remote computer is not guaranteed.
Status: mandatory Access: read-only
OBJECT-TYPE    
  Counter  

nwnetbiosDatagramBytesSentPerSec 1.3.6.1.4.1.311.1.1.3.1.1.32.1.23
Datagram Bytes Sent/sec is the rate that datagram bytes are sent from the computer. A datagram is a connectionless packet whose delivery to a remote computer is not guaranteed.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER  

nwnetbiosDatagramsReceivedPerSec 1.3.6.1.4.1.311.1.1.3.1.1.32.1.24
Datagrams Received/sec is the rate that datagrams are received by the computer. A datagram is a connectionless packet whose delivery to a remote computer is not guaranteed.
Status: mandatory Access: read-only
OBJECT-TYPE    
  Counter  

nwnetbiosDatagramBytesReceivedPerSec 1.3.6.1.4.1.311.1.1.3.1.1.32.1.25
Datagram Bytes Received/sec is the rate that datagram bytes are received by the computer. A datagram is a connectionless packet whose delivery to a remote computer is not guaranteed.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER  

nwnetbiosPacketsSentPerSec 1.3.6.1.4.1.311.1.1.3.1.1.32.1.26
Packets Sent/sec is the rate that packets are sent by the computer. This counter counts all packets sent by the computer, i.e. control as well as data packets.
Status: mandatory Access: read-only
OBJECT-TYPE    
  Counter  

nwnetbiosPacketsReceivedPerSec 1.3.6.1.4.1.311.1.1.3.1.1.32.1.27
Packets Received/sec is the rate that packets are received by the computer. This counter counts all packets processed: control as well as data packets.
Status: mandatory Access: read-only
OBJECT-TYPE    
  Counter  

nwnetbiosFramesSentPerSec 1.3.6.1.4.1.311.1.1.3.1.1.32.1.28
Frames Sent/sec is the rate that data frames are sent by the computer. This counter only counts the frames (packets) that carry data.
Status: mandatory Access: read-only
OBJECT-TYPE    
  Counter  

nwnetbiosFrameBytesSentPerSec 1.3.6.1.4.1.311.1.1.3.1.1.32.1.29
Frame Bytes Sent/sec is the rate that data bytes are sent by the computer. This counter only counts the bytes in frames (packets) that carry data.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER  

nwnetbiosFramesReceivedPerSec 1.3.6.1.4.1.311.1.1.3.1.1.32.1.30
Frames Received/sec is the rate that data frames are received by the computer. This counter only counts the frames (packets) that carry data.
Status: mandatory Access: read-only
OBJECT-TYPE    
  Counter  

nwnetbiosFrameBytesReceivedPerSec 1.3.6.1.4.1.311.1.1.3.1.1.32.1.31
Frame Bytes Received/sec is the rate that data bytes are received by the computer. This counter only counts the frames (packets) that carry data.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER  

nwnetbiosFramesRe-SentPerSec 1.3.6.1.4.1.311.1.1.3.1.1.32.1.32
Frames Re-Sent/sec is the rate that data frames (packets) are re-sent by the computer. This counter only counts the frames or packets that carry data.
Status: mandatory Access: read-only
OBJECT-TYPE    
  Counter  

nwnetbiosFrameBytesRe-SentPerSec 1.3.6.1.4.1.311.1.1.3.1.1.32.1.33
Frame Bytes Re-Sent/sec is the rate that data bytes are re-sent by the computer. This counter only counts the bytes in frames that carry data.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER  

nwnetbiosFramesRejectedPerSec 1.3.6.1.4.1.311.1.1.3.1.1.32.1.34
Frames Rejected/sec is the rate that data frames are rejected. This counter only counts the frames (packets) that carry data.
Status: mandatory Access: read-only
OBJECT-TYPE    
  Counter  

nwnetbiosFrameBytesRejectedPerSec 1.3.6.1.4.1.311.1.1.3.1.1.32.1.35
Frame Bytes Rejected/sec is the rate that data bytes are rejected. This counter only counts the bytes in data frames (packets) that carry data.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER  

nwnetbiosExpirationsResponse 1.3.6.1.4.1.311.1.1.3.1.1.32.1.36
Expirations Response is the count of T1 timer expirations.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER  

nwnetbiosExpirationsAck 1.3.6.1.4.1.311.1.1.3.1.1.32.1.37
Expirations Ack is the count of T2 timer expirations
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER  

nwnetbiosWindowSendMaximum 1.3.6.1.4.1.311.1.1.3.1.1.32.1.38
Window Send Maximum is the maximum number of bytes of data that will be sent before waiting for an acknowledgment from the remote computer.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER  

nwnetbiosWindowSendAverage 1.3.6.1.4.1.311.1.1.3.1.1.32.1.39
Window Send Average is the running average number of data bytes that were sent before waiting for an acknowledgment from the remote computer.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER  

nwnetbiosPiggybackAckQueuedPerSec 1.3.6.1.4.1.311.1.1.3.1.1.32.1.40
Piggyback Ack Queued/sec is the rate that piggybacked acknowledgments are queued. Piggyback acknowledgments are acknowledgments to received packets that are to be included in the next outgoing packet to the remote computer.
Status: mandatory Access: read-only
OBJECT-TYPE    
  Counter  

nwnetbiosPiggybackAckTimeouts 1.3.6.1.4.1.311.1.1.3.1.1.32.1.41
Piggyback Ack Timeouts is the number of times that a piggyback acknowledgment could not be sent because there was no outgoing packet to the remote on which to piggyback. A piggyback ack is an acknowledgment to a received packet that is sent along in an outgoing data packet to the remote computer. If no outgoing packet is sent within the timeout period, then an ack packet is sent and this counter is incremented.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER  

ntsystem 1.3.6.1.4.1.311.1.1.3.1.1.33
OBJECT IDENTIFIER    

ntsystemFileReadOperationsPerSec 1.3.6.1.4.1.311.1.1.3.1.1.33.1
File Read Operations/sec is an aggregate of all the file system read operations on the computer.
Status: mandatory Access: read-only
OBJECT-TYPE    
  Counter  

ntsystemFileWriteOperationsPerSec 1.3.6.1.4.1.311.1.1.3.1.1.33.2
File Write Operations/sec is an aggregate of all the file system write operations on the computer.
Status: mandatory Access: read-only
OBJECT-TYPE    
  Counter  

ntsystemFileControlOperationsPerSec 1.3.6.1.4.1.311.1.1.3.1.1.33.3
File Control Operations/sec is an aggregate of all file system operations that are neither reads nor writes. These operations usually include file system control requests or requests for information about device characteristics or status.
Status: mandatory Access: read-only
OBJECT-TYPE    
  Counter  

ntsystemFileReadBytesPerSec 1.3.6.1.4.1.311.1.1.3.1.1.33.4
File Read Bytes/sec is an aggregate of the bytes transferred for all the file system read operations on the computer.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER  

ntsystemFileWriteBytesPerSec 1.3.6.1.4.1.311.1.1.3.1.1.33.5
File Write Bytes/sec is an aggregate of the bytes transferred for all the file system write operations on the computer.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER  

ntsystemFileControlBytesPerSec 1.3.6.1.4.1.311.1.1.3.1.1.33.6
File Control Bytes/sec is an aggregate of bytes transferred for all file system operations that are neither reads nor writes. These operations usually include file system control requests or requests for information about device characteristics or status.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER  

ntsystemContextSwitchesPerSec 1.3.6.1.4.1.311.1.1.3.1.1.33.7
Context Switches/sec is the rate of switches from one thread to another. Thread switches can occur either inside of a single process or across processes. A thread switch may be caused either by one thread asking another for information, or by a thread being preempted by another, higher priority thread becoming ready to run. Unlike some early operating systems, Windows NT uses process boundaries for subsystem protection in addition to the traditional protection of User and Privileged modes. These subsystem processes provide additional protection. Therefore, some work done by Windows NT on behalf of an application may appear in other subsystem processes in addition to the Privileged Time in the application. Switching to the subsystem process causes one Context Switch in the application thread. Switching back causes another Context Switch in the subsystem thread.
Status: mandatory Access: read-only
OBJECT-TYPE    
  Counter  

ntsystemSystemCallsPerSec 1.3.6.1.4.1.311.1.1.3.1.1.33.8
Systems Calls/sec is the frequency of calls to Windows NT system service routines. These routines perform all of the basic scheduling and synchronization of activities on the computer, and provide access to non-graphical devices, memory management, and name space management.
Status: mandatory Access: read-only
OBJECT-TYPE    
  Counter  

ntsystemPercentTotalProcessorTime 1.3.6.1.4.1.311.1.1.3.1.1.33.9
The % Total Processor Time is the average percentage of time that all the processors on the system are busy executing non-idle threads. On a multi-processor system, if all processors are always busy this is 100%, if all processors are 50% busy this is 50% and if 1/4th of the processors are 100% busy this is 25%. It can be viewed as the fraction of the time spent doing useful work. Each processor is assigned an Idle thread in the Idle process which consumes those unproductive processor cycles not used by any other threads.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER  

ntsystemPercentTotalUserTime 1.3.6.1.4.1.311.1.1.3.1.1.33.10
The % Total User Time is the average percentage of time spent in User mode by all processors. On a multi-processor system, if all processors are always in User mode this is 100%, if all processors are 50% in User mode this is 50% and if 1/4th of the processors are in User mode this is 25%. Applications execute in User Mode, as do subsystems like the window manager and the graphics engine. Code executing in User Mode cannot damage the integrity of the Windows NT Executive, Kernel, and device drivers. Unlike some early operating systems, Windows NT uses process boundaries for subsystem protection in addition to the traditional protection of User and Privileged modes. These subsystem processes provide additional protection. Therefore, some work done by Windows NT on behalf of an application may appear in other subsystem processes in addition to the Privileged Time in the application process.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER  

ntsystemPercentTotalPrivilegedTime 1.3.6.1.4.1.311.1.1.3.1.1.33.11
The % Total Privileged Time is the average percentage of time spent in Privileged mode by all processors. On a multi-processor system, if all processors are always in Privileged mode this is 100%, and if 1/4th of the processors are in Privileged mode this is 25%. When a Windows NT system service is called, the service will often run in Privileged Mode in order to gain access to system-private data. Such data is protected from access by threads executing in User Mode. Calls to the system may be explicit, or they may be implicit such as when a page fault or an interrupt occurs. Unlike some early operating systems, Windows NT uses process boundaries for subsystem protection in addition to the traditional protection of User and Privileged modes. These subsystem processes provide additional protection. Therefore, some work done by Windows NT on behalf of an application may appear in other subsystem processes in addition to the Privileged Time in the application process.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER  

ntsystemTotalInterruptsPerSec 1.3.6.1.4.1.311.1.1.3.1.1.33.12
Total Interrupts/sec is the rate the computer is receiving and servicing hardware interrupts. Some devices that may generate interrupts are the system timer, the mouse, data communication lines, network interface cards and other peripheral devices. This counter provides an indication of how busy these devices are on a computer-wide basis. See also Processor:Interrupts/sec.
Status: mandatory Access: read-only
OBJECT-TYPE    
  Counter  

ntsystemFileDataOperationsPerSec 1.3.6.1.4.1.311.1.1.3.1.1.33.13
File Data Operations per second is the rate that the computer is issuing Read and Write operations to file system devices. It does not include File Control Operations.
Status: mandatory Access: read-only
OBJECT-TYPE    
  Counter  

ntsystemSystemUpTime 1.3.6.1.4.1.311.1.1.3.1.1.33.14
Total Time (in seconds) that the computer has been operational since it was last started.
Status: mandatory Access: read-only
OBJECT-TYPE    
  TimeTicks  

ntsystemProcessorQueueLength 1.3.6.1.4.1.311.1.1.3.1.1.33.15
Processor Queue Length is the instantaneous length of the processor queue in units of threads. This counter is always 0 unless you are also monitoring a thread counter. All processors use a single queue in which threads wait for processor cycles. This length does not include the threads that are currently executing. A sustained processor queue length greater than two generally indicates processor congestion. This is an instantaneous count, not an average over the time interval.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER  

ntsystemAlignmentFixupsPerSec 1.3.6.1.4.1.311.1.1.3.1.1.33.16
Alignment Fixups/sec is the rate of alignment faults fixed by the system.
Status: mandatory Access: read-only
OBJECT-TYPE    
  Counter  

ntsystemExceptionDispatchesPerSec 1.3.6.1.4.1.311.1.1.3.1.1.33.17
Exception Dispatches/sec is the rate of exceptions dispatched by the system.
Status: mandatory Access: read-only
OBJECT-TYPE    
  Counter  

ntsystemFloatingEmulationsPerSec 1.3.6.1.4.1.311.1.1.3.1.1.33.18
Floating Emulations/sec is the rate of floating emulations performed by the system.
Status: mandatory Access: read-only
OBJECT-TYPE    
  Counter  

ntsystemPercentTotalDPCTime 1.3.6.1.4.1.311.1.1.3.1.1.33.19
% Total DPC Time is the sum of % DPC Time of all processors divided by the number of processors in the system. (See Processor: % DPC Time for detail.)
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER  

ntsystemPercentTotalInterruptTime 1.3.6.1.4.1.311.1.1.3.1.1.33.20
% Total Interrupt Time is the sum of % Interrupt Time of all processors divided by the number of processors in the system. (See Processor: % Interrupt Time for detail.)
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER  

ntsystemTotalDPCsQueuedPerSec 1.3.6.1.4.1.311.1.1.3.1.1.33.21
Total DPCs Queued/sec is the rate DPC objects are queued to all processors' DPC queues.
Status: mandatory Access: read-only
OBJECT-TYPE    
  Counter  

ntsystemTotalDPCRate 1.3.6.1.4.1.311.1.1.3.1.1.33.22
Total DPC Rate is the average rate DPC objects are queued to all processors' DPC queue per clock tick.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER  

ntsystemTotalDPCBypassesPerSec 1.3.6.1.4.1.311.1.1.3.1.1.33.23
Total DPC Bypasses/sec is the overall rate Dispatch interrupts were short-circuited across all processors.
Status: mandatory Access: read-only
OBJECT-TYPE    
  Counter  

ntsystemTotalAPCBypassesPerSec 1.3.6.1.4.1.311.1.1.3.1.1.33.24
Total APC Bypasses/sec is the overall rate kernel APC interrupts were short-circuited across all processors.
Status: mandatory Access: read-only
OBJECT-TYPE    
  Counter  

ntsystemPercentRegistryQuotaInUse 1.3.6.1.4.1.311.1.1.3.1.1.33.25
% Registry Quota In Use indicates the percentage of the Total Registry Quota Allowed currently in use by the system.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER  

packet-Filtering 1.3.6.1.4.1.311.1.1.3.1.1.34
OBJECT IDENTIFIER    

packetfilterTotalDroppedFrames 1.3.6.1.4.1.311.1.1.3.1.1.34.1
The total number of dropped or filtered frames.
Status: mandatory Access: read-only
OBJECT-TYPE    
  Counter  

packetfilterFramesDroppedDueToFilterDenial 1.3.6.1.4.1.311.1.1.3.1.1.34.2
Total number of frames dropped because dynamic packet filtering did not allow the data.
Status: mandatory Access: read-only
OBJECT-TYPE    
  Counter  

packetfilterFramesDroppedDueToProtocolViolations 1.3.6.1.4.1.311.1.1.3.1.1.34.3
This is the total of the number of frames dropped because of some protocol irregularity.
Status: mandatory Access: read-only
OBJECT-TYPE    
  Counter  

packetfilterTotalIncomingConnections 1.3.6.1.4.1.311.1.1.3.1.1.34.4
This is the total of the number of connections made through the filtered interfaces.
Status: mandatory Access: read-only
OBJECT-TYPE    
  Counter  

packetfilterTotalLostLoggingFrames 1.3.6.1.4.1.311.1.1.3.1.1.34.5
This is the total of the number of frames dropped that could not be logged.
Status: mandatory Access: read-only
OBJECT-TYPE    
  Counter  

webserviceweb-ServiceTable 1.3.6.1.4.1.311.1.1.3.1.1.35
A table containing performance information for instances of 'web-Service' objects.
Status: mandatory Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    Webserviceweb-ServiceEntry

webserviceweb-ServiceEntry 1.3.6.1.4.1.311.1.1.3.1.1.35.1
Performance information for one particular instance of 'web-Service' object.
Status: mandatory Access: not-accessible
OBJECT-TYPE    
  Webserviceweb-ServiceEntry  

webserviceweb-ServiceIndex 1.3.6.1.4.1.311.1.1.3.1.1.35.1.1
Index.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER  

webserviceweb-ServiceInstance 1.3.6.1.4.1.311.1.1.3.1.1.35.1.2
Instance name.
Status: mandatory Access: read-only
OBJECT-TYPE    
  DisplayString  

webserviceBytesSentPerSec 1.3.6.1.4.1.311.1.1.3.1.1.35.1.3
Bytes Sent/sec is the rate that data bytes are sent by the Web service.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER  

webserviceBytesReceivedPerSec 1.3.6.1.4.1.311.1.1.3.1.1.35.1.4
Bytes Received/sec is the rate that data bytes are received by the Web service.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER  

webserviceBytesTotalPerSec 1.3.6.1.4.1.311.1.1.3.1.1.35.1.5
Bytes Total/sec is the sum of Bytes Sent/sec and Bytes Received/sec. This is the total rate of bytes transferred by the Web service.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER  

webserviceTotalFilesSent 1.3.6.1.4.1.311.1.1.3.1.1.35.1.6
Total Files Sent is the total number of files sent by the Web service (counted since service startup).
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER  

webserviceFilesSentPerSec 1.3.6.1.4.1.311.1.1.3.1.1.35.1.7
The rate files are sent by the Web service.
Status: mandatory Access: read-only
OBJECT-TYPE    
  Counter  

webserviceTotalFilesReceived 1.3.6.1.4.1.311.1.1.3.1.1.35.1.8
Total Files Received is the total number of files received by the Web service (counted since service startup).
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER  

webserviceFilesReceivedPerSec 1.3.6.1.4.1.311.1.1.3.1.1.35.1.9
The rate files are received by the Web service.
Status: mandatory Access: read-only
OBJECT-TYPE    
  Counter  

webserviceTotalFilesTransferred 1.3.6.1.4.1.311.1.1.3.1.1.35.1.10
Total Files Transferred is the sum of Files Sent and Files Received. This is the total number of files transferred by the Web service (counted since service startup).
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER  

webserviceFilesPerSec 1.3.6.1.4.1.311.1.1.3.1.1.35.1.11
The rate files are transferred, that is, sent and received by the Web service.
Status: mandatory Access: read-only
OBJECT-TYPE    
  Counter  

webserviceCurrentAnonymousUsers 1.3.6.1.4.1.311.1.1.3.1.1.35.1.12
Current Anonymous Users is the number of users who currently have an anonymous connection using the Web service.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER  

webserviceCurrentNonAnonymousUsers 1.3.6.1.4.1.311.1.1.3.1.1.35.1.13
Current NonAnonymous Users is the number of users who currently have a non-anonymous connection using the Web service.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER  

webserviceTotalAnonymousUsers 1.3.6.1.4.1.311.1.1.3.1.1.35.1.14
Total Anonymous Users is the total number of users who established an anonymous connection with the Web service (counted since service startup).
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER  

webserviceAnonymousUsersPerSec 1.3.6.1.4.1.311.1.1.3.1.1.35.1.15
The rate users are making anonymous connections using the Web service.
Status: mandatory Access: read-only
OBJECT-TYPE    
  Counter  

webserviceTotalNonAnonymousUsers 1.3.6.1.4.1.311.1.1.3.1.1.35.1.16
Total NonAnonymous Users is the total number of users who established a non-anonymous connection with the Web service (counted since service startup).
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER  

webserviceNonAnonymousUsersPerSec 1.3.6.1.4.1.311.1.1.3.1.1.35.1.17
The rate users are making non-anonymous connections using the Web service.
Status: mandatory Access: read-only
OBJECT-TYPE    
  Counter  

webserviceMaximumAnonymousUsers 1.3.6.1.4.1.311.1.1.3.1.1.35.1.18
Maximum Anonymous Users is the maximum number of users who established concurrent anonymous connections using the Web service (counted since service startup).
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER  

webserviceMaximumNonAnonymousUsers 1.3.6.1.4.1.311.1.1.3.1.1.35.1.19
Maximum NonAnonymous Users is the maximum number of users who established concurrent non-anonymous connections using the Web service (counted since service startup).
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER  

webserviceCurrentConnections 1.3.6.1.4.1.311.1.1.3.1.1.35.1.20
Current Connections is the current number of connections established with the Web service.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER  

webserviceMaximumConnections 1.3.6.1.4.1.311.1.1.3.1.1.35.1.21
Maximum Connections is the maximum number of simultaneous connections established with the Web service.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER  

webserviceTotalConnectionAttempts 1.3.6.1.4.1.311.1.1.3.1.1.35.1.22
Total Connection Attempts is the number of connections that have been attempted using the Web service (counted since service startup).
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER  

webserviceConnectionAttemptsPerSec 1.3.6.1.4.1.311.1.1.3.1.1.35.1.23
The rate that connections using the Web service are being attempted.
Status: mandatory Access: read-only
OBJECT-TYPE    
  Counter  

webserviceTotalLogonAttempts 1.3.6.1.4.1.311.1.1.3.1.1.35.1.24
Total Logon Attempts is the number of logons that have been attempted using the Web service (counted since service startup).
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER  

webserviceLogonAttemptsPerSec 1.3.6.1.4.1.311.1.1.3.1.1.35.1.25
The rate that logons using the Web service are being attempted.
Status: mandatory Access: read-only
OBJECT-TYPE    
  Counter  

webserviceTotalGetRequests 1.3.6.1.4.1.311.1.1.3.1.1.35.1.26
Total Get Requests is the number of HTTP requests using the GET method (counted since service startup). Get requests are generally used for basic file retrievals or image maps, though they can be used with forms.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER  

webserviceGetRequestsPerSec 1.3.6.1.4.1.311.1.1.3.1.1.35.1.27
The rate HTTP requests using the GET method are made. Get requests are generally used for basic file retrievals or image maps, though they can be used with forms.
Status: mandatory Access: read-only
OBJECT-TYPE    
  Counter  

webserviceTotalPostRequests 1.3.6.1.4.1.311.1.1.3.1.1.35.1.28
Total Post Requests is the number of HTTP requests using the POST method (counted since service startup). Post requests are generally used for forms or gateway requests.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER  

webservicePostRequestsPerSec 1.3.6.1.4.1.311.1.1.3.1.1.35.1.29
The rate HTTP requests using the POST method are made. Post requests are generally used for forms or gateway requests.
Status: mandatory Access: read-only
OBJECT-TYPE    
  Counter  

webserviceTotalHeadRequests 1.3.6.1.4.1.311.1.1.3.1.1.35.1.30
Total Head Requests is the number of HTTP requests using the HEAD method (counted since service startup). Head requests generally indicate a client is querying the state of a document they already have to see if it needs to be refreshed.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER  

webserviceHeadRequestsPerSec 1.3.6.1.4.1.311.1.1.3.1.1.35.1.31
The rate HTTP requests using the HEAD method are made. Head requests generally indicate a client is querying the state of a document they already have to see if it needs to be refreshed.
Status: mandatory Access: read-only
OBJECT-TYPE    
  Counter  

webserviceTotalPutRequests 1.3.6.1.4.1.311.1.1.3.1.1.35.1.32
Total Put Requests is the number of HTTP requests using the PUT method (counted since service startup).
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER  

webservicePutRequestsPerSec 1.3.6.1.4.1.311.1.1.3.1.1.35.1.33
The rate HTTP requests using the PUT method are made.
Status: mandatory Access: read-only
OBJECT-TYPE    
  Counter  

webserviceTotalDeleteRequests 1.3.6.1.4.1.311.1.1.3.1.1.35.1.34
Total Delete Requests is the number of HTTP requests using the DELETE method (counted since service startup). Delete requests are generally used for file removals.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER  

webserviceDeleteRequestsPerSec 1.3.6.1.4.1.311.1.1.3.1.1.35.1.35
The rate HTTP requests using the DELETE method are made. Delete requests are generally used for file removals.
Status: mandatory Access: read-only
OBJECT-TYPE    
  Counter  

webserviceTotalTraceRequests 1.3.6.1.4.1.311.1.1.3.1.1.35.1.36
Total Trace Requests is the number of HTTP requests using the TRACE method (counted since service startup). Trace requests allow the client to see what is being received at the end of the request chain and use the information for diagnostic purposes.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER  

webserviceSystemCodeResidentBytes 1.3.6.1.4.1.311.1.1.3.1.1.35.1.37
System Code Resident Bytes
Status: mandatory Access: read-only
OBJECT-TYPE    
  Counter  

webserviceTotalOtherRequestMethods 1.3.6.1.4.1.311.1.1.3.1.1.35.1.38
Total Other Request Methods is the number of HTTP requests that are not GET, POST, PUT, DELETE, TRACE or HEAD methods (counted since service startup). These may include LINK or other methods supported by gateway applications.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER  

webserviceOtherRequestMethodsPerSec 1.3.6.1.4.1.311.1.1.3.1.1.35.1.39
The rate HTTP requests are made that do not use the GET, POST, PUT, DELETE, TRACE or HEAD methods. These may include LINK or other methods supported by gateway applications.
Status: mandatory Access: read-only
OBJECT-TYPE    
  Counter  

webserviceTotalMethodRequests 1.3.6.1.4.1.311.1.1.3.1.1.35.1.40
Total Method Requests is the number of HTTP GET, POST, PUT, DELETE, TRACE, HEAD and other method requests (counted since service startup).
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER  

webserviceTotalMethodRequestsPerSec 1.3.6.1.4.1.311.1.1.3.1.1.35.1.41
The rate HTTP requests using GET, POST, PUT, DELETE, TRACE or HEAD methods are made.
Status: mandatory Access: read-only
OBJECT-TYPE    
  Counter  

webserviceTotalCGIRequests 1.3.6.1.4.1.311.1.1.3.1.1.35.1.42
Total Common Gateway Interface (CGI) requests are custom gateway executables (.exe) the administrator can install to add forms processing or other dynamic data sources. CGI requests spawn a process on the server which can be a large drain on server resources. The count is the total since service startup.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER  

webserviceCGIRequestsPerSec 1.3.6.1.4.1.311.1.1.3.1.1.35.1.43
The rate of CGI requests that are simultaneously being processed by the Web service.
Status: mandatory Access: read-only
OBJECT-TYPE    
  Counter  

webserviceTotalISAPIExtensionRequests 1.3.6.1.4.1.311.1.1.3.1.1.35.1.44
Total ISAPI Extension Requests are custom gateway Dynamic Link Libraries (.dll) the administrator can install to add forms processing or other dynamic data sources. Unlike CGI requests, ISAPI requests are simple calls to a DLL library routine, thus they are better suited to high performance gateway applications. The count is the total since service startup.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER  

webserviceISAPIExtensionRequestsPerSec 1.3.6.1.4.1.311.1.1.3.1.1.35.1.45
The rate of ISAPI Extension requests that are simultaneously being processed by the Web service.
Status: mandatory Access: read-only
OBJECT-TYPE    
  Counter  

webserviceTotalNotFoundErrors 1.3.6.1.4.1.311.1.1.3.1.1.35.1.46
Total Not Found Errors is the number of requests that couldn't be satisfied by the server because the requested document could not be found. These are generally reported as an HTTP 404 error code to the client. The count is the total since service startup.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER  

webserviceNotFoundErrorsPerSec 1.3.6.1.4.1.311.1.1.3.1.1.35.1.47
The rate of errors due to requests that couldn't be satisfied by the server because the requested document could not be found. These are generally reported as an HTTP 404 error code to the client.
Status: mandatory Access: read-only
OBJECT-TYPE    
  Counter  

webserviceCurrentCGIRequests 1.3.6.1.4.1.311.1.1.3.1.1.35.1.48
Current CGI Requests is the current number of CGI requests that are simultaneously being processed by the Web service.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER  

webserviceCurrentISAPIExtensionRequests 1.3.6.1.4.1.311.1.1.3.1.1.35.1.49
Current ISAPI Extension Requests is the current number of Extension requests that are simultaneously being processed by the Web service.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER  

webserviceMaximumCGIRequests 1.3.6.1.4.1.311.1.1.3.1.1.35.1.50
Maximum CGI Requests is the maximum number of CGI requests simultaneously processed by the Web service.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER  

webserviceMaximumISAPIExtensionRequests 1.3.6.1.4.1.311.1.1.3.1.1.35.1.51
Maximum ISAPI Extension Requests is the maximum number of Extension requests simultaneously processed by the Web service.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER  

webserviceTotalBlockedAsyncIPerORequests 1.3.6.1.4.1.311.1.1.3.1.1.35.1.52
Total requests temporarily blocked due to bandwidth throttling settings (counted since service startup).
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER  

webserviceTotalAllowedAsyncIPerORequests 1.3.6.1.4.1.311.1.1.3.1.1.35.1.53
Total requests allowed by bandwidth throttling settings (counted since service startup).
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER  

webserviceTotalRejectedAsyncIPerORequests 1.3.6.1.4.1.311.1.1.3.1.1.35.1.54
Total requests rejected due to bandwidth throttling settings (counted since service startup).
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER  

webserviceCurrentBlockedAsyncIPerORequests 1.3.6.1.4.1.311.1.1.3.1.1.35.1.55
Current requests temporarily blocked due to bandwidth throttling settings.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER  

webserviceMeasuredAsyncIPerOBandwidthUsage 1.3.6.1.4.1.311.1.1.3.1.1.35.1.56
Measured bandwidth of asynchronous I/O averaged over a minute.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER