WANSTATS-MIB

File: WANSTATS-MIB.mib (261727 bytes)

Imported modules

SNMPv2-SMI SNMPv2-TC RMON-MIB

Imported symbols

MODULE-IDENTITY OBJECT-TYPE Counter64
TimeTicks enterprises DisplayString
RowStatus OwnerString

Defined Types

WanT1E1StatsEntry  
SEQUENCE    
  wanT1E1StatsIndex INTEGER 1..65535
  wanT1E1StatsDataSource OBJECT IDENTIFIER
  wanT1E1StatsDropEvents Counter64
  wanT1E1StatsInFrames Counter64
  wanT1E1StatsOutFrames Counter64
  wanT1E1StatsInOctets Counter64
  wanT1E1StatsOutOctets Counter64
  wanT1E1StatsESs Counter64
  wanT1E1StatsSESs Counter64
  wanT1E1StatsSEFSs Counter64
  wanT1E1StatsOOFs Counter64
  wanT1E1StatsUASs Counter64
  wanT1E1StatsCSSs Counter64
  wanT1E1StatsPCVs Counter64
  wanT1E1StatsLESs Counter64
  wanT1E1StatsBESs Counter64
  wanT1E1StatsDMs Counter64
  wanT1E1StatsLCVs Counter64
  wanT1E1StatsLOFs Counter64
  wanT1E1StatsLOSs Counter64
  wanT1E1StatsRAIs Counter64
  wanT1E1StatsAISs Counter64
  wanT1E1StatsTS16AISs Counter64
  wanT1E1StatsLOMFs Counter64
  wanT1E1StatsFarLOMFs Counter64
  wanT1E1StatsOwner OwnerString
  wanT1E1StatsStatus RowStatus

WanT1E1HistoryEntry  
SEQUENCE    
  wanT1E1HistoryIndex INTEGER 1..65535
  wanT1E1HistorySampleIndex INTEGER 1..2147483647
  wanT1E1HistoryIntervalStart TimeTicks
  wanT1E1HistoryDropEvents Counter64
  wanT1E1HistoryInFrames Counter64
  wanT1E1HistoryOutFrames Counter64
  wanT1E1HistoryInOctets Counter64
  wanT1E1HistoryOutOctets Counter64
  wanT1E1HistoryESs Counter64
  wanT1E1HistorySESs Counter64
  wanT1E1HistorySEFSs Counter64
  wanT1E1HistoryOOFs Counter64
  wanT1E1HistoryUASs Counter64
  wanT1E1HistoryCSSs Counter64
  wanT1E1HistoryPCVs Counter64
  wanT1E1HistoryLESs Counter64
  wanT1E1HistoryBESs Counter64
  wanT1E1HistoryDMs Counter64
  wanT1E1HistoryLCVs Counter64
  wanT1E1HistoryLOFs Counter64
  wanT1E1HistoryLOSs Counter64
  wanT1E1HistoryAISs Counter64
  wanT1E1HistoryRAIs Counter64
  wanT1E1HistoryTS16AISs Counter64
  wanT1E1HistoryLOMFs Counter64
  wanT1E1HistoryFarLOMFs Counter64
  wanT1E1HistoryInUtilization INTEGER 0..10000
  wanT1E1HistoryOutUtilization INTEGER 0..10000

WanVSeriesStatsEntry  
SEQUENCE    
  wanVSeriesStatsIndex INTEGER 1..65535
  wanVSeriesStatsDataSource OBJECT IDENTIFIER
  wanVSeriesStatsDropEvents Counter64
  wanVSeriesStatsInFrames Counter64
  wanVSeriesStatsOutFrames Counter64
  wanVSeriesStatsInOctets Counter64
  wanVSeriesStatsOutOctets Counter64
  wanVSeriesStatsInFCSs Counter64
  wanVSeriesStatsOutFCSs Counter64
  wanVSeriesStatsInOverruns Counter64
  wanVSeriesStatsOutOverruns Counter64
  wanVSeriesStatsInterruptedFrames Counter64
  wanVSeriesStatsInAbortedFrames Counter64
  wanVSeriesStatsOutAbortedFrames Counter64
  wanVSeriesStatsOwner OwnerString
  wanVSeriesStatsStatus RowStatus

WanVSeriesHistoryEntry  
SEQUENCE    
  wanVSeriesHistoryIndex INTEGER 1..65535
  wanVSeriesHistorySampleIndex INTEGER 1..2147483647
  wanVSeriesHistoryIntervalStart TimeTicks
  wanVSeriesHistoryDropEvents Counter64
  wanVSeriesHistoryInFrames Counter64
  wanVSeriesHistoryOutFrames Counter64
  wanVSeriesHistoryInOctets Counter64
  wanVSeriesHistoryOutOctets Counter64
  wanVSeriesHistoryInFCSs Counter64
  wanVSeriesHistoryOutFCSs Counter64
  wanVSeriesHistoryInOverruns Counter64
  wanVSeriesHistoryOutOverruns Counter64
  wanVSeriesHistoryInterruptedFrames Counter64
  wanVSeriesHistoryInAbortedFrames Counter64
  wanVSeriesHistoryOutAbortedFrames Counter64
  wanVSeriesHistoryInUtilization INTEGER 0..10000
  wanVSeriesHistoryOutUtilization INTEGER 0..10000

WanHssiStatsEntry  
SEQUENCE    
  wanHssiStatsIndex INTEGER 1..65535
  wanHssiStatsDataSource OBJECT IDENTIFIER
  wanHssiStatsDropEvents Counter64
  wanHssiStatsInFrames Counter64
  wanHssiStatsOutFrames Counter64
  wanHssiStatsInOctets Counter64
  wanHssiStatsOutOctets Counter64
  wanHssiStatsRxLongFrames Counter64
  wanHssiStatsRxCrcErrors Counter64
  wanHssiStatsRxOverruns Counter64
  wanHssiStatsRxAborts Counter64
  wanHssiStatsTxAborts Counter64
  wanHssiStatsTxUnderruns Counter64
  wanHssiStatsRxRingErrors Counter64
  wanHssiStatsRxRingOverruns Counter64
  wanHssiStatsTxRingErrors Counter64
  wanHssiStatsPortOpErrors Counter64
  wanHssiStatsTxCmplProcessings Counter64
  wanHssiStatsOwner OwnerString
  wanHssiStatsStatus RowStatus

WanHssiHistoryEntry  
SEQUENCE    
  wanHssiHistoryIndex INTEGER 1..65535
  wanHssiHistorySampleIndex INTEGER 1..2147483647
  wanHssiHistoryIntervalStart TimeTicks
  wanHssiHistoryDropEvents Counter64
  wanHssiHistoryInFrames Counter64
  wanHssiHistoryOutFrames Counter64
  wanHssiHistoryInOctets Counter64
  wanHssiHistoryOutOctets Counter64
  wanHssiHistoryRxLongFrames Counter64
  wanHssiHistoryRxCrcErrors Counter64
  wanHssiHistoryRxOverruns Counter64
  wanHssiHistoryRxAborts Counter64
  wanHssiHistoryTxAborts Counter64
  wanHssiHistoryTxUnderruns Counter64
  wanHssiHistoryRxRingErrors Counter64
  wanHssiHistoryRxRingOverruns Counter64
  wanHssiHistoryTxRingErrors Counter64
  wanHssiHistoryPortOpErrors Counter64
  wanHssiHistoryTxCmplProcessings Counter64
  wanHssiHistoryInUtilization INTEGER 0..10000
  wanHssiHistoryOutUtilization INTEGER 0..10000

WanT3E3StatsEntry  
SEQUENCE    
  wanT3E3StatsIndex INTEGER 1..65535
  wanT3E3StatsDataSource OBJECT IDENTIFIER
  wanT3E3StatsDropEvents Counter64
  wanT3E3StatsInFrames Counter64
  wanT3E3StatsOutFrames Counter64
  wanT3E3StatsInOctets Counter64
  wanT3E3StatsOutOctets Counter64
  wanT3E3StatsPESs Counter64
  wanT3E3StatsPSESs Counter64
  wanT3E3StatsOOFs Counter64
  wanT3E3StatsSEFSs Counter64
  wanT3E3StatsUASs Counter64
  wanT3E3StatsLCVs Counter64
  wanT3E3StatsPCVs Counter64
  wanT3E3StatsLESs Counter64
  wanT3E3StatsCCVs Counter64
  wanT3E3StatsCESs Counter64
  wanT3E3StatsCSESs Counter64
  wanT3E3StatsRAIs Counter64
  wanT3E3StatsAISs Counter64
  wanT3E3StatsLOFs Counter64
  wanT3E3StatsLOSs Counter64
  wanT3E3StatsOwner OwnerString
  wanT3E3StatsStatus RowStatus

WanT3E3HistoryEntry  
SEQUENCE    
  wanT3E3HistoryIndex INTEGER 1..65535
  wanT3E3HistorySampleIndex INTEGER 1..2147483647
  wanT3E3HistoryIntervalStart TimeTicks
  wanT3E3HistoryDropEvents Counter64
  wanT3E3HistoryInFrames Counter64
  wanT3E3HistoryOutFrames Counter64
  wanT3E3HistoryInOctets Counter64
  wanT3E3HistoryOutOctets Counter64
  wanT3E3HistoryPESs Counter64
  wanT3E3HistoryPSESs Counter64
  wanT3E3HistoryOOFs Counter64
  wanT3E3HistorySEFSs Counter64
  wanT3E3HistoryUASs Counter64
  wanT3E3HistoryLCVs Counter64
  wanT3E3HistoryPCVs Counter64
  wanT3E3HistoryLESs Counter64
  wanT3E3HistoryCCVs Counter64
  wanT3E3HistoryCESs Counter64
  wanT3E3HistoryCSESs Counter64
  wanT3E3HistoryRAIs Counter64
  wanT3E3HistoryAISs Counter64
  wanT3E3HistoryLOFs Counter64
  wanT3E3HistoryLOSs Counter64
  wanT3E3HistoryInUtilization INTEGER 0..10000
  wanT3E3HistoryOutUtilization INTEGER 0..10000

WanAtmStatsEntry  
SEQUENCE    
  wanAtmStatsIndex INTEGER 1..65535
  wanAtmStatsDataSource OBJECT IDENTIFIER
  wanAtmStatsDropEvents Counter64
  wanAtmStatsInCells Counter64
  wanAtmStatsOutCells Counter64
  wanAtmStatsInCLP1 Counter64
  wanAtmStatsOutCLP1 Counter64
  wanAtmStatsConnectionEvents Counter64
  wanAtmStatsErroredPDUs Counter64
  wanAtmStatsSetupAttempts Counter64
  wanAtmStatsInRoutesUnavailable Counter64
  wanAtmStatsOutRoutesUnavailable Counter64
  wanAtmStatsInResourcesUnavailable Counter64
  wanAtmStatsOutResourcesUnavailable Counter64
  wanAtmStatsInUnsuccessfulCalls Counter64
  wanAtmStatsOutUnsuccessfulCalls Counter64
  wanAtmStatsInIncorrectMsgs Counter64
  wanAtmStatsOutIncorrectMsgs Counter64
  wanAtmStatsInPartyEvents Counter64
  wanAtmStatsOutPartyEvents Counter64
  wanAtmStatsInExpiries Counter64
  wanAtmStatsOutExpiries Counter64
  wanAtmStatsInRestartErrors Counter64
  wanAtmStatsOutRestartErrors Counter64
  wanAtmStatsInSVCs Counter64
  wanAtmStatsOutSVCs Counter64
  wanAtmStatsInOCDs Counter64
  wanAtmStatsOutOCDs Counter64
  wanAtmStatsInLOCs Counter64
  wanAtmStatsOutLOCs Counter64
  wanAtmStatsInLOFs Counter64
  wanAtmStatsOutLOFs Counter64
  wanAtmStatsInLOPs Counter64
  wanAtmStatsOutLOPs Counter64
  wanAtmStatsInLOSs Counter64
  wanAtmStatsOutLOSs Counter64
  wanAtmStatsOwner OwnerString
  wanAtmStatsStatus RowStatus

WanAtmHistoryEntry  
SEQUENCE    
  wanAtmHistoryIndex INTEGER 1..65535
  wanAtmHistorySampleIndex INTEGER 1..2147483647
  wanAtmHistoryIntervalStart TimeTicks
  wanAtmHistoryDropEvents Counter64
  wanAtmHistoryInCells Counter64
  wanAtmHistoryOutCells Counter64
  wanAtmHistoryInCLP1 Counter64
  wanAtmHistoryOutCLP1 Counter64
  wanAtmHistoryConnectionEvents Counter64
  wanAtmHistoryErroredPDUs Counter64
  wanAtmHistorySetupAttempts Counter64
  wanAtmHistoryInRoutesUnavailable Counter64
  wanAtmHistoryOutRoutesUnavailable Counter64
  wanAtmHistoryInResourcesUnavailable Counter64
  wanAtmHistoryOutResourcesUnavailable Counter64
  wanAtmHistoryInUnsuccessfulCalls Counter64
  wanAtmHistoryOutUnsuccessfulCalls Counter64
  wanAtmHistoryInIncorrectMsgs Counter64
  wanAtmHistoryOutIncorrectMsgs Counter64
  wanAtmHistoryInPartyEvents Counter64
  wanAtmHistoryOutPartyEvents Counter64
  wanAtmHistoryInExpiries Counter64
  wanAtmHistoryOutExpiries Counter64
  wanAtmHistoryInRestartErrors Counter64
  wanAtmHistoryOutRestartErrors Counter64
  wanAtmHistoryInSVCs Counter64
  wanAtmHistoryOutSVCs Counter64
  wanAtmHistoryInOCDs Counter64
  wanAtmHistoryOutOCDs Counter64
  wanAtmHistoryInLOCs Counter64
  wanAtmHistoryOutLOCs Counter64
  wanAtmHistoryInLOFs Counter64
  wanAtmHistoryOutLOFs Counter64
  wanAtmHistoryInLOPs Counter64
  wanAtmHistoryOutLOPs Counter64
  wanAtmHistoryInLOSs Counter64
  wanAtmHistoryOutLOSs Counter64
  wanAtmHistoryInUtilization INTEGER 0..10000
  wanAtmHistoryOutUtilization INTEGER 0..10000

WanX25StatsEntry  
SEQUENCE    
  wanX25StatsIndex INTEGER 1..65535
  wanX25StatsDataSource OBJECT IDENTIFIER
  wanX25StatsDropEvents Counter64
  wanX25StatsInFrames Counter64
  wanX25StatsOutFrames Counter64
  wanX25StatsInOctets Counter64
  wanX25StatsOutOctets Counter64
  wanX25StatsInRejects Counter64
  wanX25StatsOutRejects Counter64
  wanX25StatsInAttempts Counter64
  wanX25StatsOutAttempts Counter64
  wanX25StatsInFailures Counter64
  wanX25StatsOutFailures Counter64
  wanX25StatsProviderClears Counter64
  wanX25StatsInResets Counter64
  wanX25StatsOutResets Counter64
  wanX25StatsProviderResets Counter64
  wanX25StatsInAccusedErrors Counter64
  wanX25StatsOutAccusedErrors Counter64
  wanX25StatsInInterrupts Counter64
  wanX25StatsOutInterrupts Counter64
  wanX25StatsOwner OwnerString
  wanX25StatsStatus RowStatus

WanX25HistoryEntry  
SEQUENCE    
  wanX25HistoryIndex INTEGER 1..65535
  wanX25HistorySampleIndex INTEGER 1..2147483647
  wanX25HistoryIntervalStart TimeTicks
  wanX25HistoryDropEvents Counter64
  wanX25HistoryInFrames Counter64
  wanX25HistoryOutFrames Counter64
  wanX25HistoryInOctets Counter64
  wanX25HistoryOutOctets Counter64
  wanX25HistoryInRejects Counter64
  wanX25HistoryOutRejects Counter64
  wanX25HistoryInAttempts Counter64
  wanX25HistoryOutAttempts Counter64
  wanX25HistoryInFailures Counter64
  wanX25HistoryOutFailures Counter64
  wanX25HistoryProviderClears Counter64
  wanX25HistoryInResets Counter64
  wanX25HistoryOutResets Counter64
  wanX25HistoryProviderResets Counter64
  wanX25HistoryInAccusedErrors Counter64
  wanX25HistoryOutAccusedErrors Counter64
  wanX25HistoryInInterrupts Counter64
  wanX25HistoryOutInterrupts Counter64
  wanX25HistoryInUtilization INTEGER 0..10000
  wanX25HistoryOutUtilization INTEGER 0..10000

WanFrStatsEntry  
SEQUENCE    
  wanFrStatsIndex INTEGER 1..65535
  wanFrStatsDataSource OBJECT IDENTIFIER
  wanFrStatsDropEvents Counter64
  wanFrStatsInFrames Counter64
  wanFrStatsOutFrames Counter64
  wanFrStatsInOctets Counter64
  wanFrStatsOutOctets Counter64
  wanFrStatsInFECNs Counter64
  wanFrStatsOutFECNs Counter64
  wanFrStatsInBECNs Counter64
  wanFrStatsOutBECNs Counter64
  wanFrStatsInDEs Counter64
  wanFrStatsOutDEs Counter64
  wanFrStatsOwner OwnerString
  wanFrStatsStatus RowStatus

WanFrHistoryEntry  
SEQUENCE    
  wanFrHistoryIndex INTEGER 1..65535
  wanFrHistorySampleIndex INTEGER 1..2147483647
  wanFrHistoryIntervalStart TimeTicks
  wanFrHistoryDropEvents Counter64
  wanFrHistoryInFrames Counter64
  wanFrHistoryOutFrames Counter64
  wanFrHistoryInOctets Counter64
  wanFrHistoryOutOctets Counter64
  wanFrHistoryInFECNs Counter64
  wanFrHistoryOutFECNs Counter64
  wanFrHistoryInBECNs Counter64
  wanFrHistoryOutBECNs Counter64
  wanFrHistoryInDEs Counter64
  wanFrHistoryOutDEs Counter64
  wanFrHistoryInUtilization INTEGER 0..10000
  wanFrHistoryOutUtilization INTEGER 0..10000

WanAal5StatsEntry  
SEQUENCE    
  wanAal5StatsIndex INTEGER 1..65535
  wanAal5StatsDataSource OBJECT IDENTIFIER
  wanAal5StatsDropEvents Counter64
  wanAal5StatsInCells Counter64
  wanAal5StatsOutCells Counter64
  wanAal5StatsInPDUs Counter64
  wanAal5StatsOutPDUs Counter64
  wanAal5StatsInOctets Counter64
  wanAal5StatsOutOctets Counter64
  wanAal5StatsInCLP1 Counter64
  wanAal5StatsOutCLP1 Counter64
  wanAal5StatsInCRCs Counter64
  wanAal5StatsOutCRCs Counter64
  wanAal5StatsInOversizedSDUs Counter64
  wanAal5StatsOutOversizedSDUs Counter64
  wanAal5StatsInSVCs Counter64
  wanAal5StatsOutSVCs Counter64
  wanAal5StatsOwner OwnerString
  wanAal5StatsStatus RowStatus

WanAal5HistoryEntry  
SEQUENCE    
  wanAal5HistoryIndex INTEGER 1..65535
  wanAal5HistorySampleIndex INTEGER 1..2147483647
  wanAal5HistoryIntervalStart TimeTicks
  wanAal5HistoryDropEvents Counter64
  wanAal5HistoryInCells Counter64
  wanAal5HistoryOutCells Counter64
  wanAal5HistoryInPDUs Counter64
  wanAal5HistoryOutPDUs Counter64
  wanAal5HistoryInOctets Counter64
  wanAal5HistoryOutOctets Counter64
  wanAal5HistoryInCLP1 Counter64
  wanAal5HistoryOutCLP1 Counter64
  wanAal5HistoryInCRCs Counter64
  wanAal5HistoryOutCRCs Counter64
  wanAal5HistoryInOversizedSDUs Counter64
  wanAal5HistoryOutOversizedSDUs Counter64
  wanAal5HistoryInSVCs Counter64
  wanAal5HistoryOutSVCs Counter64
  wanAal5HistoryInUtilization INTEGER 0..10000
  wanAal5HistoryOutUtilization INTEGER 0..10000

WanPppStatsEntry  
SEQUENCE    
  wanPppStatsIndex INTEGER 1..65535
  wanPppStatsDataSource OBJECT IDENTIFIER
  wanPppStatsDropEvents Counter64
  wanPppStatsInFrames Counter64
  wanPppStatsOutFrames Counter64
  wanPppStatsInOctets Counter64
  wanPppStatsOutOctets Counter64
  wanPppStatsInBadAddresses Counter64
  wanPppStatsOutBadAddresses Counter64
  wanPppStatsInBadControls Counter64
  wanPppStatsOutBadControls Counter64
  wanPppStatsInLongFrames Counter64
  wanPppStatsOutLongFrames Counter64
  wanPppStatsInBadFCSs Counter64
  wanPppStatsOutBadFCSs Counter64
  wanPppStatsOwner OwnerString
  wanPppStatsStatus RowStatus

WanPppHistoryEntry  
SEQUENCE    
  wanPppHistoryIndex INTEGER 1..65535
  wanPppHistorySampleIndex INTEGER 1..2147483647
  wanPppHistoryIntervalStart TimeTicks
  wanPppHistoryDropEvents Counter64
  wanPppHistoryInFrames Counter64
  wanPppHistoryOutFrames Counter64
  wanPppHistoryInOctets Counter64
  wanPppHistoryOutOctets Counter64
  wanPppHistoryInBadAddresses Counter64
  wanPppHistoryOutBadAddresses Counter64
  wanPppHistoryInBadControls Counter64
  wanPppHistoryOutBadControls Counter64
  wanPppHistoryInLongFrames Counter64
  wanPppHistoryOutLongFrames Counter64
  wanPppHistoryInBadFCSs Counter64
  wanPppHistoryOutBadFCSs Counter64
  wanPppHistoryInUtilization INTEGER 0..10000
  wanPppHistoryOutUtilization INTEGER 0..10000

WanX25PvcStatsEntry  
SEQUENCE    
  wanX25PvcStatsIndex INTEGER 1..65535
  wanX25PvcStatsDataSource OBJECT IDENTIFIER
  wanX25PvcStatsDropEvents Counter64
  wanX25PvcStatsInFrames Counter64
  wanX25PvcStatsOutFrames Counter64
  wanX25PvcStatsInOctets Counter64
  wanX25PvcStatsOutOctets Counter64
  wanX25PvcStatsInResets Counter64
  wanX25PvcStatsOutResets Counter64
  wanX25PvcStatsProviderResets Counter64
  wanX25PvcStatsInAccusedErrors Counter64
  wanX25PvcStatsOutAccusedErrors Counter64
  wanX25PvcStatsInInterrupts Counter64
  wanX25PvcStatsOutInterrupts Counter64
  wanX25PvcStatsUpTime TimeTicks
  wanX25PvcStatsDownTime TimeTicks
  wanX25PvcStatsState INTEGER
  wanX25PvcStatsStateChanges Counter64
  wanX25PvcStatsOwner OwnerString
  wanX25PvcStatsStatus RowStatus

WanX25PvcHistoryEntry  
SEQUENCE    
  wanX25PvcHistoryIndex INTEGER 1..65535
  wanX25PvcHistorySampleIndex INTEGER 1..2147483647
  wanX25PvcHistoryIntervalStart TimeTicks
  wanX25PvcHistoryDropEvents Counter64
  wanX25PvcHistoryInFrames Counter64
  wanX25PvcHistoryOutFrames Counter64
  wanX25PvcHistoryInOctets Counter64
  wanX25PvcHistoryOutOctets Counter64
  wanX25PvcHistoryInResets Counter64
  wanX25PvcHistoryOutResets Counter64
  wanX25PvcHistoryProviderResets Counter64
  wanX25PvcHistoryInAccusedErrors Counter64
  wanX25PvcHistoryOutAccusedErrors Counter64
  wanX25PvcHistoryInInterrupts Counter64
  wanX25PvcHistoryOutInterrupts Counter64
  wanX25PvcHistoryUpTime TimeTicks
  wanX25PvcHistoryDownTime TimeTicks
  wanX25PvcHistoryStateChanges Counter64
  wanX25PvcHistoryInUtilization INTEGER 0..10000
  wanX25PvcHistoryOutUtilization INTEGER 0..10000

WanFrPvcStatsEntry  
SEQUENCE    
  wanFrPvcStatsIndex INTEGER 1..65535
  wanFrPvcStatsDataSource OBJECT IDENTIFIER
  wanFrPvcStatsDropEvents Counter64
  wanFrPvcStatsInFrames Counter64
  wanFrPvcStatsOutFrames Counter64
  wanFrPvcStatsInOctets Counter64
  wanFrPvcStatsOutOctets Counter64
  wanFrPvcStatsInFECNs Counter64
  wanFrPvcStatsOutFECNs Counter64
  wanFrPvcStatsInBECNs Counter64
  wanFrPvcStatsOutBECNs Counter64
  wanFrPvcStatsInDEs Counter64
  wanFrPvcStatsOutDEs Counter64
  wanFrPvcStatsUpTime TimeTicks
  wanFrPvcStatsDownTime TimeTicks
  wanFrPvcStatsState INTEGER
  wanFrPvcStatsStateChanges Counter64
  wanFrPvcStatsOwner OwnerString
  wanFrPvcStatsStatus RowStatus

WanFrPvcHistoryEntry  
SEQUENCE    
  wanFrPvcHistoryIndex INTEGER 1..65535
  wanFrPvcHistorySampleIndex INTEGER 1..2147483647
  wanFrPvcHistoryIntervalStart TimeTicks
  wanFrPvcHistoryDropEvents Counter64
  wanFrPvcHistoryInFrames Counter64
  wanFrPvcHistoryOutFrames Counter64
  wanFrPvcHistoryInOctets Counter64
  wanFrPvcHistoryOutOctets Counter64
  wanFrPvcHistoryInFECNs Counter64
  wanFrPvcHistoryOutFECNs Counter64
  wanFrPvcHistoryInBECNs Counter64
  wanFrPvcHistoryOutBECNs Counter64
  wanFrPvcHistoryInDEs Counter64
  wanFrPvcHistoryOutDEs Counter64
  wanFrPvcHistoryUpTime TimeTicks
  wanFrPvcHistoryDownTime TimeTicks
  wanFrPvcHistoryStateChanges Counter64
  wanFrPvcHistoryInUtilization INTEGER 0..10000
  wanFrPvcHistoryOutUtilization INTEGER 0..10000

WanAal5PvcStatsEntry  
SEQUENCE    
  wanAal5PvcStatsIndex INTEGER 1..65535
  wanAal5PvcStatsDataSource OBJECT IDENTIFIER
  wanAal5PvcStatsDropEvents Counter64
  wanAal5PvcStatsInCells Counter64
  wanAal5PvcStatsOutCells Counter64
  wanAal5PvcStatsInPDUs Counter64
  wanAal5PvcStatsOutPDUs Counter64
  wanAal5PvcStatsInOctets Counter64
  wanAal5PvcStatsOutOctets Counter64
  wanAal5PvcStatsInCLP1 Counter64
  wanAal5PvcStatsOutCLP1 Counter64
  wanAal5PvcStatsInCRCs Counter64
  wanAal5PvcStatsOutCRCs Counter64
  wanAal5PvcStatsInOversizedSDUs Counter64
  wanAal5PvcStatsOutOversizedSDUs Counter64
  wanAal5PvcStatsUpTime TimeTicks
  wanAal5PvcStatsDownTime TimeTicks
  wanAal5PvcStatsState INTEGER
  wanAal5PvcStatsStateChanges Counter64
  wanAal5PvcStatsOwner OwnerString
  wanAal5PvcStatsStatus RowStatus

WanAal5PvcHistoryEntry  
SEQUENCE    
  wanAal5PvcHistoryIndex INTEGER 1..65535
  wanAal5PvcHistorySampleIndex INTEGER 1..2147483647
  wanAal5PvcHistoryIntervalStart TimeTicks
  wanAal5PvcHistoryDropEvents Counter64
  wanAal5PvcHistoryInCells Counter64
  wanAal5PvcHistoryOutCells Counter64
  wanAal5PvcHistoryInPDUs Counter64
  wanAal5PvcHistoryOutPDUs Counter64
  wanAal5PvcHistoryInOctets Counter64
  wanAal5PvcHistoryOutOctets Counter64
  wanAal5PvcHistoryInCLP1 Counter64
  wanAal5PvcHistoryOutCLP1 Counter64
  wanAal5PvcHistoryInCRCs Counter64
  wanAal5PvcHistoryOutCRCs Counter64
  wanAal5PvcHistoryInOversizedSDUs Counter64
  wanAal5PvcHistoryOutOversizedSDUs Counter64
  wanAal5PvcHistoryUpTime TimeTicks
  wanAal5PvcHistoryDownTime TimeTicks
  wanAal5PvcHistoryStateChanges Counter64
  wanAal5PvcHistoryInUtilization INTEGER 0..10000
  wanAal5PvcHistoryOutUtilization INTEGER 0..10000

Defined Values

hp 1.3.6.1.4.1.11
OBJECT IDENTIFIER    

nm 1.3.6.1.4.1.11.2
OBJECT IDENTIFIER    

system 1.3.6.1.4.1.11.2.3
OBJECT IDENTIFIER    

netElement 1.3.6.1.4.1.11.2.3.7
OBJECT IDENTIFIER    

lanprobe 1.3.6.1.4.1.11.2.3.7.6
OBJECT IDENTIFIER    

general 1.3.6.1.4.1.11.2.3.7.6.1
OBJECT IDENTIFIER    

rmonExtension 1.3.6.1.4.1.11.2.3.7.6.1.5
OBJECT IDENTIFIER    

statsExtension 1.3.6.1.4.1.11.2.3.7.6.1.5.1
OBJECT IDENTIFIER    

wanStatsMIB 1.3.6.1.4.1.11.2.3.7.6.1.5.1.8
The MIB containing RMON media statistics for WAN links.
MODULE-IDENTITY    

wanStatsMIBObjects 1.3.6.1.4.1.11.2.3.7.6.1.5.1.8.1
OBJECT IDENTIFIER    

wanSignalingStats 1.3.6.1.4.1.11.2.3.7.6.1.5.1.8.1.1
OBJECT IDENTIFIER    

wanProtocolStats 1.3.6.1.4.1.11.2.3.7.6.1.5.1.8.1.2
OBJECT IDENTIFIER    

wanPvcStats 1.3.6.1.4.1.11.2.3.7.6.1.5.1.8.1.3
OBJECT IDENTIFIER    

wanHistoryMIBObjects 1.3.6.1.4.1.11.2.3.7.6.1.5.1.8.2
OBJECT IDENTIFIER    

wanSignalingHistory 1.3.6.1.4.1.11.2.3.7.6.1.5.1.8.2.1
OBJECT IDENTIFIER    

wanProtocolHistory 1.3.6.1.4.1.11.2.3.7.6.1.5.1.8.2.2
OBJECT IDENTIFIER    

wanPvcHistory 1.3.6.1.4.1.11.2.3.7.6.1.5.1.8.2.3
OBJECT IDENTIFIER    

wanT1E1StatsTable 1.3.6.1.4.1.11.2.3.7.6.1.5.1.8.1.1.1
T1/E1 signaling statistics.
OBJECT-TYPE    
  SEQUENCE OF  
    WanT1E1StatsEntry

wanT1E1StatsEntry 1.3.6.1.4.1.11.2.3.7.6.1.5.1.8.1.1.1.1
Statistics for a T1/E1 interface. The near end of the link refers to the side of the link that the probe is monitoring. The far end is the side the probe is not on.
OBJECT-TYPE    
  WanT1E1StatsEntry  

wanT1E1StatsIndex 1.3.6.1.4.1.11.2.3.7.6.1.5.1.8.1.1.1.1.1
The value of this object uniquely identifies this wanT1E1StatsTable entry.
OBJECT-TYPE    
  INTEGER 1..65535  

wanT1E1StatsDataSource 1.3.6.1.4.1.11.2.3.7.6.1.5.1.8.1.1.1.1.2
This object identifies the source of the data that this wanT1E1StatsEntry analyzes. This source can be any DS1 or E1 interface on this device. In order to identify a particular interface, this object shall identify the instance of the ifIndex object, defined in MIB-II [RFC 1573] for the desired interface. The ifType value associated with the ifIndex can only be ds1(18).
OBJECT-TYPE    
  OBJECT IDENTIFIER  

wanT1E1StatsDropEvents 1.3.6.1.4.1.11.2.3.7.6.1.5.1.8.1.1.1.1.3
The total number of events in which frames were dropped by the probe due to lack of resources. Note that this number is not necessarily the number of frames dropped; it is just the number of times this condition has been detected.
OBJECT-TYPE    
  Counter64  

wanT1E1StatsInFrames 1.3.6.1.4.1.11.2.3.7.6.1.5.1.8.1.1.1.1.4
The total number of frames seen originating from the far end of the link including errored frames.
OBJECT-TYPE    
  Counter64  

wanT1E1StatsOutFrames 1.3.6.1.4.1.11.2.3.7.6.1.5.1.8.1.1.1.1.5
The total number of frames seen originating from the near end of the link including errored frames.
OBJECT-TYPE    
  Counter64  

wanT1E1StatsInOctets 1.3.6.1.4.1.11.2.3.7.6.1.5.1.8.1.1.1.1.6
The sum of octets from all frames seen originating from the far end of the link including errored frames.
OBJECT-TYPE    
  Counter64  

wanT1E1StatsOutOctets 1.3.6.1.4.1.11.2.3.7.6.1.5.1.8.1.1.1.1.7
The sum of octets from all frames seen originating from the near end of the link including errored frames.
OBJECT-TYPE    
  Counter64  

wanT1E1StatsESs 1.3.6.1.4.1.11.2.3.7.6.1.5.1.8.1.1.1.1.8
For ESF and E1-CRC links an Errored Second is a second with one or more Path Code Violations OR one or more Out of Frame defects OR one or more Controlled Slip events OR a detected AIS defect. For D4 and E1-noCRC links, the presence of Bipolar Violations also triggers an Errored Second. This is not incremented during an Unavailable Second.
OBJECT-TYPE    
  Counter64  

wanT1E1StatsSESs 1.3.6.1.4.1.11.2.3.7.6.1.5.1.8.1.1.1.1.9
A Severely Errored Second for ESF signals is a second with 320 or more Path Code Violation Error Events OR one or more Out of Frame defects OR a detected AIS defect. For E1-CRC signals, a Severely Errored Second is a second with 832 or more Path Code Violation error events OR one or more Out of Frame defects. For E1-noCRC signals, a Severely Errored Second is a 2048 LCVs or more. For D4 signals, a Severely Errored Second is a count of one-second intervals with Framing Error events, or an OOF defect, or 1544 LCVs or more. Controlled slips are not included in this parameter. This is not incremented during an Unavailable Second.
OBJECT-TYPE    
  Counter64  

wanT1E1StatsSEFSs 1.3.6.1.4.1.11.2.3.7.6.1.5.1.8.1.1.1.1.10
An Severely Errored Framing Second is a second with one or more Out of Frame defects OR a detected AIS defect.
OBJECT-TYPE    
  Counter64  

wanT1E1StatsOOFs 1.3.6.1.4.1.11.2.3.7.6.1.5.1.8.1.1.1.1.11
An OOF defect is the occurrence of a particular density of Framing Error events. For T1 links, an Out of Frame defect is declared when the receiver detects two or more framing errors within a 3 msec period for ESF signals and 0.75 msec for D4 signals, or two or more errors out of five or fewer consecutive framing-bits. For E1 links, an Out Of Frame defect is declared when three consecutive frame alignment signals have been received with an error (see G.706 Section 4.1 [17]). Once an Out Of Frame Defect is declared, the framer starts searching for a correct framing pattern. The Out of Frame defect ends when the signal is in frame. In-frame occurs when there are fewer than two frame bit errors within 3 msec period for ESF signals and 0.75 msec for D4 signals. For E1 links, in-frame occurs when a) in frame N the frame alignment signal is correct and b) in frame N+1 the frame alignment signal is absent (i.e., bit 2 in TS0 is a one) and c) in frame N+2 the frame alignment signal is present and correct.
OBJECT-TYPE    
  Counter64  

wanT1E1StatsUASs 1.3.6.1.4.1.11.2.3.7.6.1.5.1.8.1.1.1.1.12
Unavailable Seconds (UAS) are calculated by counting the number of seconds that the interface is unavailable. The DS1 interface is said to be unavailable from the onset of 10 contiguous SESs, or the onset of the condition leading to a failure (see Failure States). If the condition leading to the failure was immediately preceded by one or more contiguous SESs, then the DS1 interface unavailability starts from the onset of these SESs. Once unavailable, and if no failure is present, the DS1 interface becomes available at the onset of 10 contiguous seconds with no SESs. Once unavailable, and if a failure is present, the DS1 interface becomes available at the onset of 10 contiguous seconds with no SESs, if the failure clearing time is less than or equal to 10 seconds. If the failure clearing time is more than 10 seconds, the DS1 interface becomes available at the onset of 10 contiguous seconds with no SESs, or the onset period leading to the successful clearing condition, whichever occurs later. With respect to the DS1 error counts, all counters are incremented while the DS1 interface is deemed available. While the interface is deemed unavailable, the only count that is incremented is UASs.
OBJECT-TYPE    
  Counter64  

wanT1E1StatsCSSs 1.3.6.1.4.1.11.2.3.7.6.1.5.1.8.1.1.1.1.13
A Controlled Slip Second is a one-second interval containing one or more controlled slips.
OBJECT-TYPE    
  Counter64  

wanT1E1StatsPCVs 1.3.6.1.4.1.11.2.3.7.6.1.5.1.8.1.1.1.1.14
A Path Coding Violation error event is a frame synchronization bit error in the D4 and E1-noCRC formats, or a CRC error in the ESF and E1-CRC formats.
OBJECT-TYPE    
  Counter64  

wanT1E1StatsLESs 1.3.6.1.4.1.11.2.3.7.6.1.5.1.8.1.1.1.1.15
A Line Errored Second, according to T1M1.3, is a second in which one or more Line Code Violation error events were detected. While many implementations are currently unable to detect the zero strings, it is expected that interface manufacturers will add this capability in deference to ANSI; therefore, it will become available in time. In the T1M1.3 specification, near end Line Code Violations and far end Line Errored Seconds are counted. For consistency, we count Line Errored Seconds at both ends.
OBJECT-TYPE    
  Counter64  

wanT1E1StatsBESs 1.3.6.1.4.1.11.2.3.7.6.1.5.1.8.1.1.1.1.16
A Bursty Errored Second (also known as Errored Second type B) is a second with fewer than 320 and more than 1 Path Coding Violation error events, no Severely Errored Frame defects and no detected incoming AIS defects. Controlled slips are not included in this parameter. This is not incremented during an Unavailable Second.
OBJECT-TYPE    
  Counter64  

wanT1E1StatsDMs 1.3.6.1.4.1.11.2.3.7.6.1.5.1.8.1.1.1.1.17
A Degraded Minute is one in which the estimated error rate exceeds 1E-6 but does not exceed 1E-3 (see G.821 [15]). Degraded Minutes are determined by collecting all of the Available Seconds, removing any Severely Errored Seconds grouping the result in 60-second long groups and counting a 60-second long group (a.k.a., minute) as degraded if the cumulative errors during the seconds present in the group exceed 1E-6. Available seconds are merely those seconds which are not Unavailable as described below.
OBJECT-TYPE    
  Counter64  

wanT1E1StatsLCVs 1.3.6.1.4.1.11.2.3.7.6.1.5.1.8.1.1.1.1.18
A Line Coding Violation (LCV) is the occurrence of either a Bipolar Violation (BPV) or Excessive Zeroes (EXZ) Error Event.
OBJECT-TYPE    
  Counter64  

wanT1E1StatsLOFs 1.3.6.1.4.1.11.2.3.7.6.1.5.1.8.1.1.1.1.19
For T1 links, the Loss Of Frame failure is declared when an OOF or LOS defect has persisted for T seconds, where 2 <= T <= 10. The Loss Of Frame failure is cleared when there have been no OOF or LOS defects during a period T where 0 <= T <= 20. Many systems will perform 'hit integration' within the period T before declaring or clearing the failure e.g., see TR 62411 [16]. For E1 links, the Loss Of Frame Failure is declared when an OOF defect is detected.
OBJECT-TYPE    
  Counter64  

wanT1E1StatsLOSs 1.3.6.1.4.1.11.2.3.7.6.1.5.1.8.1.1.1.1.20
For T1, the Loss Of Signal failure is declared upon observing 175 +/- 75 contiguous pulse positions with no pulses of either positive or negative polarity. The LOS failure is cleared upon observing an average pulse density of at least 12.5% over a period of 175 +/- 75 contiguous pulse positions starting with the receipt of a pulse. For E1 links, the Loss Of Signal failure is declared when greater than 10 consecutive zeroes are detected (see O.162 Section 3.4.4).
OBJECT-TYPE    
  Counter64  

wanT1E1StatsRAIs 1.3.6.1.4.1.11.2.3.7.6.1.5.1.8.1.1.1.1.21
The Far End Alarm failure is also known as 'Yellow Alarm' in the T1 case and 'Distant Alarm' in the E1 case. For D4 links, the Far End Alarm failure is declared when bit 6 of all channels has been zero for at least 335 ms and is cleared when bit 6 of at least one channel is non-zero for a period T, where T is usually less than one second and always less than 5 seconds. The Far End Alarm failure is not declared for D4 links when a Loss of Signal is detected. For ESF links, the Far End Alarm failure is declared if the Yellow Alarm signal pattern occurs in at least seven out of ten contiguous 16-bit pattern intervals and is cleared if the Yellow Alarm signal pattern does not occur in ten contiguous 16-bit signal pattern intervals. For E1 links, the Far End Alarm failure is declared when bit 3 of time-slot zero is received set to one on two consecutive occasions. The Far End Alarm failure is cleared when bit 3 of time-slot zero is received set to zero.
OBJECT-TYPE    
  Counter64  

wanT1E1StatsAISs 1.3.6.1.4.1.11.2.3.7.6.1.5.1.8.1.1.1.1.22
The Alarm Indication Signal failure is declared when an AIS defect is detected at the input and the AIS defect still exists after the Loss Of Frame failure (which is caused by the unframed nature of the 'all-ones' signal) is declared. The AIS failure is cleared when the Loss Of Frame failure is cleared.
OBJECT-TYPE    
  Counter64  

wanT1E1StatsTS16AISs 1.3.6.1.4.1.11.2.3.7.6.1.5.1.8.1.1.1.1.23
For E1 links, the TS16 Alarm Indication Signal failure is declared when time-slot 16 is received as all ones for all frames of two consecutive multiframes (see G.732 Section 4.2.6). This condition is never declared for T1.
OBJECT-TYPE    
  Counter64  

wanT1E1StatsLOMFs 1.3.6.1.4.1.11.2.3.7.6.1.5.1.8.1.1.1.1.24
The Loss Of MultiFrame failure is declared when two consecutive multiframe alignment signals (bits 4 through 7 of TS16 of frame 0) have been received with an error. The Loss Of Multiframe failure is cleared when the first correct multiframe alignment signal is received. The Loss Of Multiframe failure can only be declared for E1 links operating with G.732 [18] framing (sometimes called 'Channel Associated Signalling' mode).
OBJECT-TYPE    
  Counter64  

wanT1E1StatsFarLOMFs 1.3.6.1.4.1.11.2.3.7.6.1.5.1.8.1.1.1.1.25
The Far End Loss Of Multiframe failure is declared when bit 2 of TS16 of frame 0 is received set to one on two consecutive occasions. The Far End Loss Of Multiframe failure is cleared when bit 2 of TS16 of frame 0 is received set to zero. The Far End Loss Of Multiframe failure can only be declared for E1 links operating in 'Channel Associated Signalling' mode.
OBJECT-TYPE    
  Counter64  

wanT1E1StatsOwner 1.3.6.1.4.1.11.2.3.7.6.1.5.1.8.1.1.1.1.26
The entity that configured this entry.
OBJECT-TYPE    
  OwnerString  

wanT1E1StatsStatus 1.3.6.1.4.1.11.2.3.7.6.1.5.1.8.1.1.1.1.27
The status of this wanT1E1StatsTable entry.
OBJECT-TYPE    
  RowStatus  

wanT1E1HistoryTable 1.3.6.1.4.1.11.2.3.7.6.1.5.1.8.2.1.1
T1/E1 signaling statistics.
OBJECT-TYPE    
  SEQUENCE OF  
    WanT1E1HistoryEntry

wanT1E1HistoryEntry 1.3.6.1.4.1.11.2.3.7.6.1.5.1.8.2.1.1.1
Statistics for a particular T1/E1 interface. The near end of the link refers to the side of the link that the probe is monitoring. The far end is the side the probe is not on.
OBJECT-TYPE    
  WanT1E1HistoryEntry  

wanT1E1HistoryIndex 1.3.6.1.4.1.11.2.3.7.6.1.5.1.8.2.1.1.1.1
The history of which this entry is a port. The history identified by a particular value of this index is the same history as identified by the same value of historyControlIndex.
OBJECT-TYPE    
  INTEGER 1..65535  

wanT1E1HistorySampleIndex 1.3.6.1.4.1.11.2.3.7.6.1.5.1.8.2.1.1.1.2
An index that uniquely identifies the particular sample this entry represents among all samples associated with the same historyControlEntry. This index starts at 1 and increases by one as each new sample is taken.
OBJECT-TYPE    
  INTEGER 1..2147483647  

wanT1E1HistoryIntervalStart 1.3.6.1.4.1.11.2.3.7.6.1.5.1.8.2.1.1.1.3
The value of sysUpTime at the start of the interval over which this sample was measured. If the probe keeps track of time of day, it should start the first sample of the history at a time such that when the next hour of the day begins, a sample is started at that instant. Note that following this rule may require the probe to delay collection the first sample of the history, as each sample must be of the same interval. Also note that the sample which is currently being collected is not accessible in this table until the end of its interval.
OBJECT-TYPE    
  TimeTicks  

wanT1E1HistoryDropEvents 1.3.6.1.4.1.11.2.3.7.6.1.5.1.8.2.1.1.1.4
The change in value of wanT1E1StatsDropEvents during the interval.
OBJECT-TYPE    
  Counter64  

wanT1E1HistoryInFrames 1.3.6.1.4.1.11.2.3.7.6.1.5.1.8.2.1.1.1.5
The change in value of wanT1E1StatsInFrames during the interval.
OBJECT-TYPE    
  Counter64  

wanT1E1HistoryOutFrames 1.3.6.1.4.1.11.2.3.7.6.1.5.1.8.2.1.1.1.6
The change in value of wanT1E1StatsOutFrames during the interval.
OBJECT-TYPE    
  Counter64  

wanT1E1HistoryInOctets 1.3.6.1.4.1.11.2.3.7.6.1.5.1.8.2.1.1.1.7
The change in value of wanT1E1StatsInOctets during the interval.
OBJECT-TYPE    
  Counter64  

wanT1E1HistoryOutOctets 1.3.6.1.4.1.11.2.3.7.6.1.5.1.8.2.1.1.1.8
The change in value of wanT1E1StatsOutOctets during the interval.
OBJECT-TYPE    
  Counter64  

wanT1E1HistoryESs 1.3.6.1.4.1.11.2.3.7.6.1.5.1.8.2.1.1.1.9
The change in value of wanT1E1StatsESs during the interval.
OBJECT-TYPE    
  Counter64  

wanT1E1HistorySESs 1.3.6.1.4.1.11.2.3.7.6.1.5.1.8.2.1.1.1.10
The change in value of wanT1E1StatsSESs during the interval.
OBJECT-TYPE    
  Counter64  

wanT1E1HistorySEFSs 1.3.6.1.4.1.11.2.3.7.6.1.5.1.8.2.1.1.1.11
The change in value of wanT1E1StatsSEFSs during the interval.
OBJECT-TYPE    
  Counter64  

wanT1E1HistoryOOFs 1.3.6.1.4.1.11.2.3.7.6.1.5.1.8.2.1.1.1.12
The change in value of wanT1E1StatsOOFs during the interval.
OBJECT-TYPE    
  Counter64  

wanT1E1HistoryUASs 1.3.6.1.4.1.11.2.3.7.6.1.5.1.8.2.1.1.1.13
The change in value of wanT1E1StatsUASs during the interval.
OBJECT-TYPE    
  Counter64  

wanT1E1HistoryCSSs 1.3.6.1.4.1.11.2.3.7.6.1.5.1.8.2.1.1.1.14
The change in value of wanT1E1StatsCSSs during the interval.
OBJECT-TYPE    
  Counter64  

wanT1E1HistoryPCVs 1.3.6.1.4.1.11.2.3.7.6.1.5.1.8.2.1.1.1.15
The change in value of wanT1E1StatsPCVs during the interval.
OBJECT-TYPE    
  Counter64  

wanT1E1HistoryLESs 1.3.6.1.4.1.11.2.3.7.6.1.5.1.8.2.1.1.1.16
The change in value of wanT1E1StatsLESs during the interval.
OBJECT-TYPE    
  Counter64  

wanT1E1HistoryBESs 1.3.6.1.4.1.11.2.3.7.6.1.5.1.8.2.1.1.1.17
The change in value of wanT1E1StatsBESs during the interval.
OBJECT-TYPE    
  Counter64  

wanT1E1HistoryDMs 1.3.6.1.4.1.11.2.3.7.6.1.5.1.8.2.1.1.1.18
The change in value of wanT1E1StatsDMs during the interval.
OBJECT-TYPE    
  Counter64  

wanT1E1HistoryLCVs 1.3.6.1.4.1.11.2.3.7.6.1.5.1.8.2.1.1.1.19
The change in value of wanT1E1StatsLCVs during the interval.
OBJECT-TYPE    
  Counter64  

wanT1E1HistoryLOFs 1.3.6.1.4.1.11.2.3.7.6.1.5.1.8.2.1.1.1.20
The change in value of wanT1E1StatsLOFSs during the interval.
OBJECT-TYPE    
  Counter64  

wanT1E1HistoryLOSs 1.3.6.1.4.1.11.2.3.7.6.1.5.1.8.2.1.1.1.21
The change in value of wanT1E1StatsLOSs during the interval.
OBJECT-TYPE    
  Counter64  

wanT1E1HistoryRAIs 1.3.6.1.4.1.11.2.3.7.6.1.5.1.8.2.1.1.1.22
The change in value of wanT1E1StatsRAIs during the interval.
OBJECT-TYPE    
  Counter64  

wanT1E1HistoryAISs 1.3.6.1.4.1.11.2.3.7.6.1.5.1.8.2.1.1.1.23
The change in value of wanT1E1StatsAISs during the interval.
OBJECT-TYPE    
  Counter64  

wanT1E1HistoryTS16AISs 1.3.6.1.4.1.11.2.3.7.6.1.5.1.8.2.1.1.1.24
The change in value of wanT1E1StatsTS16AISs during the interval.
OBJECT-TYPE    
  Counter64  

wanT1E1HistoryLOMFs 1.3.6.1.4.1.11.2.3.7.6.1.5.1.8.2.1.1.1.25
The change in value of wanT1E1StatsLOMFs during the interval.
OBJECT-TYPE    
  Counter64  

wanT1E1HistoryFarLOMFs 1.3.6.1.4.1.11.2.3.7.6.1.5.1.8.2.1.1.1.26
The change in value of wanT1E1StatsFarLOMFs during the interval.
OBJECT-TYPE    
  Counter64  

wanT1E1HistoryInUtilization 1.3.6.1.4.1.11.2.3.7.6.1.5.1.8.2.1.1.1.27
The best estimated of the mean physical layer network utilization of traffic coming from the far end of the link in hundreds of a percent.
OBJECT-TYPE    
  INTEGER 0..10000  

wanT1E1HistoryOutUtilization 1.3.6.1.4.1.11.2.3.7.6.1.5.1.8.2.1.1.1.28
The best estimated of the mean physical layer network utilization of traffic coming from the near end of the link in hundreds of a percent.
OBJECT-TYPE    
  INTEGER 0..10000  

wanVSeriesStatsTable 1.3.6.1.4.1.11.2.3.7.6.1.5.1.8.1.1.2
V-series interface statistics.
OBJECT-TYPE    
  SEQUENCE OF  
    WanVSeriesStatsEntry

wanVSeriesStatsEntry 1.3.6.1.4.1.11.2.3.7.6.1.5.1.8.1.1.2.1
The statistics for a V-series interface. The near end of the link refers to the side of the link that the probe is monitoring. The far end is the side the probe is not on.
OBJECT-TYPE    
  WanVSeriesStatsEntry  

wanVSeriesStatsIndex 1.3.6.1.4.1.11.2.3.7.6.1.5.1.8.1.1.2.1.1
The value of this object uniquely identifies this wanVSeriesStatsTable entry.
OBJECT-TYPE    
  INTEGER 1..65535  

wanVSeriesStatsDataSource 1.3.6.1.4.1.11.2.3.7.6.1.5.1.8.1.1.2.1.2
This object identifies the source of the data that this wanVSeriesStatsEntry analyzes. This source can be and V-series interface on this device. In order to identify a particular interface, this object shall identify the instance of the ifIndex object, defined in MIB-II [RFC 1573] for the desired interface. The ifType value associated with the ifIndex can only be rs232(33) , v35(45), v11(64), or v36(65).
OBJECT-TYPE    
  OBJECT IDENTIFIER  

wanVSeriesStatsDropEvents 1.3.6.1.4.1.11.2.3.7.6.1.5.1.8.1.1.2.1.3
The total number of events in which frames were dropped by the probe due to lack of resources. Note that this number is not necessarily the number of frames dropped; it is just the number of times this condition has been detected.
OBJECT-TYPE    
  Counter64  

wanVSeriesStatsInFrames 1.3.6.1.4.1.11.2.3.7.6.1.5.1.8.1.1.2.1.4
The total number of frames seen originating from the far end of the link including errored.
OBJECT-TYPE    
  Counter64  

wanVSeriesStatsOutFrames 1.3.6.1.4.1.11.2.3.7.6.1.5.1.8.1.1.2.1.5
The total number of frames seen originating from the near end of the link including errored frames.
OBJECT-TYPE    
  Counter64  

wanVSeriesStatsInOctets 1.3.6.1.4.1.11.2.3.7.6.1.5.1.8.1.1.2.1.6
The sum of octets from all frames seen originating from the far end of the link including errored frames.
OBJECT-TYPE    
  Counter64  

wanVSeriesStatsOutOctets 1.3.6.1.4.1.11.2.3.7.6.1.5.1.8.1.1.2.1.7
The sum of octets from all frames seen originating from the near end of the link including errored frames.
OBJECT-TYPE    
  Counter64  

wanVSeriesStatsInFCSs 1.3.6.1.4.1.11.2.3.7.6.1.5.1.8.1.1.2.1.8
Total number of frames with an invalid frame check from the far end of the link.
OBJECT-TYPE    
  Counter64  

wanVSeriesStatsOutFCSs 1.3.6.1.4.1.11.2.3.7.6.1.5.1.8.1.1.2.1.9
Total number of frames with an invalid frame check from the near end of the link.
OBJECT-TYPE    
  Counter64  

wanVSeriesStatsInOverruns 1.3.6.1.4.1.11.2.3.7.6.1.5.1.8.1.1.2.1.10
Total number of frames from the far end of the link that failed to be received because the receiver did not accept the data in time.
OBJECT-TYPE    
  Counter64  

wanVSeriesStatsOutOverruns 1.3.6.1.4.1.11.2.3.7.6.1.5.1.8.1.1.2.1.11
Total number of frames from the near end of the link that failed to be received because the receiver did not accept the data in time.
OBJECT-TYPE    
  Counter64  

wanVSeriesStatsInterruptedFrames 1.3.6.1.4.1.11.2.3.7.6.1.5.1.8.1.1.2.1.12
Total number of frames that failed to be received or transmitted on the port due to loss of modem signals.
OBJECT-TYPE    
  Counter64  

wanVSeriesStatsInAbortedFrames 1.3.6.1.4.1.11.2.3.7.6.1.5.1.8.1.1.2.1.13
Number of frames from the far end of the link aborted on the port due to receiving an abort sequence.
OBJECT-TYPE    
  Counter64  

wanVSeriesStatsOutAbortedFrames 1.3.6.1.4.1.11.2.3.7.6.1.5.1.8.1.1.2.1.14
Number of frames from the near end of the link aborted on the port due to receiving an abort sequence.
OBJECT-TYPE    
  Counter64  

wanVSeriesStatsOwner 1.3.6.1.4.1.11.2.3.7.6.1.5.1.8.1.1.2.1.15
The entity that configured this entry.
OBJECT-TYPE    
  OwnerString  

wanVSeriesStatsStatus 1.3.6.1.4.1.11.2.3.7.6.1.5.1.8.1.1.2.1.16
The status of this wanVSeriesStatsTable entry.
OBJECT-TYPE    
  RowStatus  

wanVSeriesHistoryTable 1.3.6.1.4.1.11.2.3.7.6.1.5.1.8.2.1.2
The history of which this entry is a port. The history identified by a particular value of this index is the same history as identified by the same value of historyControlIndex.
OBJECT-TYPE    
  SEQUENCE OF  
    WanVSeriesHistoryEntry

wanVSeriesHistoryEntry 1.3.6.1.4.1.11.2.3.7.6.1.5.1.8.2.1.2.1
The statistics for a V-series interface. The near end of the link refers to the side of the link that the probe is monitoring. The far end is the side the probe is not on.
OBJECT-TYPE    
  WanVSeriesHistoryEntry  

wanVSeriesHistoryIndex 1.3.6.1.4.1.11.2.3.7.6.1.5.1.8.2.1.2.1.1
The history of which this entry is a port. The history identified by a particular value of this index is the same history as identified by the same value of historyControlIndex.
OBJECT-TYPE    
  INTEGER 1..65535  

wanVSeriesHistorySampleIndex 1.3.6.1.4.1.11.2.3.7.6.1.5.1.8.2.1.2.1.2
An index that uniquely identifies the particular sample this entry represents among all samples associated with the same historyControlEntry. This index starts at 1 and increases by one as each new sample is taken.
OBJECT-TYPE    
  INTEGER 1..2147483647  

wanVSeriesHistoryIntervalStart 1.3.6.1.4.1.11.2.3.7.6.1.5.1.8.2.1.2.1.3
The value of sysUpTime at the start of the interval over which this sample was measured. If the probe keeps track of time of day, it should start the first sample of the history at a time such that when the next hour of the day begins, a sample is started at that instant. Note that following this rule may require the probe to delay collection the first sample of the history, as each sample must be of the same interval. Also note that the sample which is currently being collected is not accessible in this table until the end of its interval.
OBJECT-TYPE    
  TimeTicks  

wanVSeriesHistoryDropEvents 1.3.6.1.4.1.11.2.3.7.6.1.5.1.8.2.1.2.1.4
The change in value of wanVSeriesStatsDropEvents during the interval.
OBJECT-TYPE    
  Counter64  

wanVSeriesHistoryInFrames 1.3.6.1.4.1.11.2.3.7.6.1.5.1.8.2.1.2.1.5
The change in value of wanVSeriesStatsInFrames during the interval.
OBJECT-TYPE    
  Counter64  

wanVSeriesHistoryOutFrames 1.3.6.1.4.1.11.2.3.7.6.1.5.1.8.2.1.2.1.6
The change in value of wanVSeriesStatsOutFrames during the interval.
OBJECT-TYPE    
  Counter64  

wanVSeriesHistoryInOctets 1.3.6.1.4.1.11.2.3.7.6.1.5.1.8.2.1.2.1.7
The change in value of wanVSeriesStatsInOctets during the interval.
OBJECT-TYPE    
  Counter64  

wanVSeriesHistoryOutOctets 1.3.6.1.4.1.11.2.3.7.6.1.5.1.8.2.1.2.1.8
The change in value of wanVSeriesStatsOutOctets during the interval.
OBJECT-TYPE    
  Counter64  

wanVSeriesHistoryInFCSs 1.3.6.1.4.1.11.2.3.7.6.1.5.1.8.2.1.2.1.9
The change in value of wanVSeriesStatsInFCSs during the interval.
OBJECT-TYPE    
  Counter64  

wanVSeriesHistoryOutFCSs 1.3.6.1.4.1.11.2.3.7.6.1.5.1.8.2.1.2.1.10
The change in value of wanVSeriesStatsOutFCSs during the interval.
OBJECT-TYPE    
  Counter64  

wanVSeriesHistoryInOverruns 1.3.6.1.4.1.11.2.3.7.6.1.5.1.8.2.1.2.1.11
The change in value of wanVSeriesStatsInOverruns during the interval.
OBJECT-TYPE    
  Counter64  

wanVSeriesHistoryOutOverruns 1.3.6.1.4.1.11.2.3.7.6.1.5.1.8.2.1.2.1.12
The change in value of wanVSeriesStatsOutOverruns during the interval.
OBJECT-TYPE    
  Counter64  

wanVSeriesHistoryInterruptedFrames 1.3.6.1.4.1.11.2.3.7.6.1.5.1.8.2.1.2.1.13
The change in value of wanVSeriesStatsInterruptedFrames during the interval.
OBJECT-TYPE    
  Counter64  

wanVSeriesHistoryInAbortedFrames 1.3.6.1.4.1.11.2.3.7.6.1.5.1.8.2.1.2.1.14
The change in value of wanVSeriesStatsInAbortedFrames during the interval.
OBJECT-TYPE    
  Counter64  

wanVSeriesHistoryOutAbortedFrames 1.3.6.1.4.1.11.2.3.7.6.1.5.1.8.2.1.2.1.15
The change in value of wanVSeriesStatsOutAbortedFrames during the interval.
OBJECT-TYPE    
  Counter64  

wanVSeriesHistoryInUtilization 1.3.6.1.4.1.11.2.3.7.6.1.5.1.8.2.1.2.1.16
The best estimated of the mean physical layer network utilization of traffic coming from the far end of the link in hundreds of a percent.
OBJECT-TYPE    
  INTEGER 0..10000  

wanVSeriesHistoryOutUtilization 1.3.6.1.4.1.11.2.3.7.6.1.5.1.8.2.1.2.1.17
The best estimated of the mean physical layer network utilization of traffic coming from the near end of the link in hundreds of a percent.
OBJECT-TYPE    
  INTEGER 0..10000  

wanHssiStatsTable 1.3.6.1.4.1.11.2.3.7.6.1.5.1.8.1.1.3
HSSI interface statistics.
OBJECT-TYPE    
  SEQUENCE OF  
    WanHssiStatsEntry

wanHssiStatsEntry 1.3.6.1.4.1.11.2.3.7.6.1.5.1.8.1.1.3.1
The statistics for a HSSI interface. The near end of the link refers to the side of the link that the probe is monitoring. The far end is the side the probe is not on.
OBJECT-TYPE    
  WanHssiStatsEntry  

wanHssiStatsIndex 1.3.6.1.4.1.11.2.3.7.6.1.5.1.8.1.1.3.1.1
The value of this object uniquely identifies this wanHssiStatsTable entry.
OBJECT-TYPE    
  INTEGER 1..65535  

wanHssiStatsDataSource 1.3.6.1.4.1.11.2.3.7.6.1.5.1.8.1.1.3.1.2
This object identifies the source of the data that this wanT1E1StatsEntry analyzes. This source can be any HSSI interface on this device. In order to identify a particular interface, this object shall identify the instance of the ifIndex object, defined in MIB-II [RFC 1573] for the desired interface. The ifType value associated with the ifIndex can only be hssi(46).
OBJECT-TYPE    
  OBJECT IDENTIFIER  

wanHssiStatsDropEvents 1.3.6.1.4.1.11.2.3.7.6.1.5.1.8.1.1.3.1.3
The total number of events in which frames were dropped by the probe due to lack of resources. Note that this number is not necessarily the number of frames dropped; it is just the number of times this condition has been detected.
OBJECT-TYPE    
  Counter64  

wanHssiStatsInFrames 1.3.6.1.4.1.11.2.3.7.6.1.5.1.8.1.1.3.1.4
The total number of frames seen originating from the far end of the link including errored frames.
OBJECT-TYPE    
  Counter64  

wanHssiStatsOutFrames 1.3.6.1.4.1.11.2.3.7.6.1.5.1.8.1.1.3.1.5
The total number of frames seen originating from the near end of the link including errored frames.
OBJECT-TYPE    
  Counter64  

wanHssiStatsInOctets 1.3.6.1.4.1.11.2.3.7.6.1.5.1.8.1.1.3.1.6
The sum of octets from all frames seen originating from the far end of the link including errored frames.
OBJECT-TYPE    
  Counter64  

wanHssiStatsOutOctets 1.3.6.1.4.1.11.2.3.7.6.1.5.1.8.1.1.3.1.7
The sum of octets from all frames seen originating from the near end of the link including errored frames.
OBJECT-TYPE    
  Counter64  

wanHssiStatsRxLongFrames 1.3.6.1.4.1.11.2.3.7.6.1.5.1.8.1.1.3.1.8
Number of long frames from the far end of the link.
OBJECT-TYPE    
  Counter64  

wanHssiStatsRxCrcErrors 1.3.6.1.4.1.11.2.3.7.6.1.5.1.8.1.1.3.1.9
Number of frames from far end of link with CRC errors.
OBJECT-TYPE    
  Counter64  

wanHssiStatsRxOverruns 1.3.6.1.4.1.11.2.3.7.6.1.5.1.8.1.1.3.1.10
Number of frames from far end of link with FIFO overrun errors.
OBJECT-TYPE    
  Counter64  

wanHssiStatsRxAborts 1.3.6.1.4.1.11.2.3.7.6.1.5.1.8.1.1.3.1.11
Number of frames from far end of link with abort status.
OBJECT-TYPE    
  Counter64  

wanHssiStatsTxAborts 1.3.6.1.4.1.11.2.3.7.6.1.5.1.8.1.1.3.1.12
Number of frames from near end of link with internal abort errors.
OBJECT-TYPE    
  Counter64  

wanHssiStatsTxUnderruns 1.3.6.1.4.1.11.2.3.7.6.1.5.1.8.1.1.3.1.13
Number of frames from near end of link aborted with underrun errors.
OBJECT-TYPE    
  Counter64  

wanHssiStatsRxRingErrors 1.3.6.1.4.1.11.2.3.7.6.1.5.1.8.1.1.3.1.14
Number of receive ring error events.
OBJECT-TYPE    
  Counter64  

wanHssiStatsRxRingOverruns 1.3.6.1.4.1.11.2.3.7.6.1.5.1.8.1.1.3.1.15
Number of receive ring overrun events.
OBJECT-TYPE    
  Counter64  

wanHssiStatsTxRingErrors 1.3.6.1.4.1.11.2.3.7.6.1.5.1.8.1.1.3.1.16
Number of transmit ring error events.
OBJECT-TYPE    
  Counter64  

wanHssiStatsPortOpErrors 1.3.6.1.4.1.11.2.3.7.6.1.5.1.8.1.1.3.1.17
Number of port operation error events.
OBJECT-TYPE    
  Counter64  

wanHssiStatsTxCmplProcessings 1.3.6.1.4.1.11.2.3.7.6.1.5.1.8.1.1.3.1.18
Number of transmit complete processings (TINT).
OBJECT-TYPE    
  Counter64  

wanHssiStatsOwner 1.3.6.1.4.1.11.2.3.7.6.1.5.1.8.1.1.3.1.19
The entity that configured this entry.
OBJECT-TYPE    
  OwnerString  

wanHssiStatsStatus 1.3.6.1.4.1.11.2.3.7.6.1.5.1.8.1.1.3.1.20
The status of this wanHssiStatsTable entry.
OBJECT-TYPE    
  RowStatus  

wanHssiHistoryTable 1.3.6.1.4.1.11.2.3.7.6.1.5.1.8.2.1.3
HSSI interface statistics.
OBJECT-TYPE    
  SEQUENCE OF  
    WanHssiHistoryEntry

wanHssiHistoryEntry 1.3.6.1.4.1.11.2.3.7.6.1.5.1.8.2.1.3.1
The statistics for a HSSI interface. The near end of the link refers to the side of the link that the probe is monitoring. The far end is the side the probe is not on.
OBJECT-TYPE    
  WanHssiHistoryEntry  

wanHssiHistoryIndex 1.3.6.1.4.1.11.2.3.7.6.1.5.1.8.2.1.3.1.1
The history of which this entry is a port. The history identified by a particular value of this index is the same history as identified by the same value of historyControlIndex.
OBJECT-TYPE    
  INTEGER 1..65535  

wanHssiHistorySampleIndex 1.3.6.1.4.1.11.2.3.7.6.1.5.1.8.2.1.3.1.2
An index that uniquely identifies the particular sample this entry represents among all samples associated with the same historyControlEntry. This index starts at 1 and increases by one as each new sample is taken.
OBJECT-TYPE    
  INTEGER 1..2147483647  

wanHssiHistoryIntervalStart 1.3.6.1.4.1.11.2.3.7.6.1.5.1.8.2.1.3.1.3
The value of sysUpTime at the start of the interval over which this sample was measured. If the probe keeps track of time of day, it should start the first sample of the history at a time such that when the next hour of the day begins, a sample is started at that instant. Note that following this rule may require the probe to delay collection the first sample of the history, as each sample must be of the same interval. Also note that the sample which is currently being collected is not accessible in this table until the end of its interval.
OBJECT-TYPE    
  TimeTicks  

wanHssiHistoryDropEvents 1.3.6.1.4.1.11.2.3.7.6.1.5.1.8.2.1.3.1.4
The change in value of wanHssiStatsDropEvents during the interval.
OBJECT-TYPE    
  Counter64  

wanHssiHistoryInFrames 1.3.6.1.4.1.11.2.3.7.6.1.5.1.8.2.1.3.1.5
The change in value of wanHssiStatsInFrames during the interval.
OBJECT-TYPE    
  Counter64  

wanHssiHistoryOutFrames 1.3.6.1.4.1.11.2.3.7.6.1.5.1.8.2.1.3.1.6
The change in value of wanHssiStatsOutFrames during the interval.
OBJECT-TYPE    
  Counter64  

wanHssiHistoryInOctets 1.3.6.1.4.1.11.2.3.7.6.1.5.1.8.2.1.3.1.7
The change in value of wanHssiStatsInOctets during the interval.
OBJECT-TYPE    
  Counter64  

wanHssiHistoryOutOctets 1.3.6.1.4.1.11.2.3.7.6.1.5.1.8.2.1.3.1.8
The change in value of wanHssiStatsOutOctets during the interval.
OBJECT-TYPE    
  Counter64  

wanHssiHistoryRxLongFrames 1.3.6.1.4.1.11.2.3.7.6.1.5.1.8.2.1.3.1.9
The change in value of wanHssiStatsRxLongFrames during the interval.
OBJECT-TYPE    
  Counter64  

wanHssiHistoryRxCrcErrors 1.3.6.1.4.1.11.2.3.7.6.1.5.1.8.2.1.3.1.10
The change in value of wanHssiStatsRxCrcErrors during the interval.
OBJECT-TYPE    
  Counter64  

wanHssiHistoryRxOverruns 1.3.6.1.4.1.11.2.3.7.6.1.5.1.8.2.1.3.1.11
The change in value of wanHssiStatsRxOverruns during the interval.
OBJECT-TYPE    
  Counter64  

wanHssiHistoryRxAborts 1.3.6.1.4.1.11.2.3.7.6.1.5.1.8.2.1.3.1.12
The change in value of wanHssiStatsRxAborts during the interval.
OBJECT-TYPE    
  Counter64  

wanHssiHistoryTxAborts 1.3.6.1.4.1.11.2.3.7.6.1.5.1.8.2.1.3.1.13
The change in value of wanHssiStatsTxAborts during the interval.
OBJECT-TYPE    
  Counter64  

wanHssiHistoryTxUnderruns 1.3.6.1.4.1.11.2.3.7.6.1.5.1.8.2.1.3.1.14
The change in value of wanHssiStatsTxUnderruns during the interval.
OBJECT-TYPE    
  Counter64  

wanHssiHistoryRxRingErrors 1.3.6.1.4.1.11.2.3.7.6.1.5.1.8.2.1.3.1.15
The change in value of wanHssiStatsTxRingErrors during the interval.
OBJECT-TYPE    
  Counter64  

wanHssiHistoryRxRingOverruns 1.3.6.1.4.1.11.2.3.7.6.1.5.1.8.2.1.3.1.16
The change in value of wanHssiStatsRxRingOverruns during the interval.
OBJECT-TYPE    
  Counter64  

wanHssiHistoryTxRingErrors 1.3.6.1.4.1.11.2.3.7.6.1.5.1.8.2.1.3.1.17
The change in value of wanHssiStatsTxRingErrors during the interval.
OBJECT-TYPE    
  Counter64  

wanHssiHistoryPortOpErrors 1.3.6.1.4.1.11.2.3.7.6.1.5.1.8.2.1.3.1.18
The change in value of wanHssiStatsPortOpErrors during the interval.
OBJECT-TYPE    
  Counter64  

wanHssiHistoryTxCmplProcessings 1.3.6.1.4.1.11.2.3.7.6.1.5.1.8.2.1.3.1.19
The change in value of wanHssiStatsTxCmplProcessings during the interval.
OBJECT-TYPE    
  Counter64  

wanHssiHistoryInUtilization 1.3.6.1.4.1.11.2.3.7.6.1.5.1.8.2.1.3.1.20
The best estimated of the mean physical layer network utilization of traffic coming from the far end of the link in hundreds of a percent.
OBJECT-TYPE    
  INTEGER 0..10000  

wanHssiHistoryOutUtilization 1.3.6.1.4.1.11.2.3.7.6.1.5.1.8.2.1.3.1.21
The best estimated of the mean physical layer network utilization of traffic coming from the near end of the link in hundreds of a percent.
OBJECT-TYPE    
  INTEGER 0..10000  

wanT3E3StatsTable 1.3.6.1.4.1.11.2.3.7.6.1.5.1.8.1.1.4
T3/E3 signaling statistics
OBJECT-TYPE    
  SEQUENCE OF  
    WanT3E3StatsEntry

wanT3E3StatsEntry 1.3.6.1.4.1.11.2.3.7.6.1.5.1.8.1.1.4.1
Statistics for a T3/E3 interface. The near end of the link refers to the side of the link that the probe is monitoring. The far end is the side the probe is not on.
OBJECT-TYPE    
  WanT3E3StatsEntry  

wanT3E3StatsIndex 1.3.6.1.4.1.11.2.3.7.6.1.5.1.8.1.1.4.1.1
The value of this object uniquely identifies this wanT3E3StatsTable entry.
OBJECT-TYPE    
  INTEGER 1..65535  

wanT3E3StatsDataSource 1.3.6.1.4.1.11.2.3.7.6.1.5.1.8.1.1.4.1.2
This object identifies the source of the data that this wanT3E3StatsEntry analyzes. This source can be any DS3 or E3 interface on this device. In order to identify a particular interface, this object shall identify the instance of the ifIndex object, defined in MIB-II [RFC 1573] for the desired interface. The ifType value of the associated ifIndex can only be ds3(30).
OBJECT-TYPE    
  OBJECT IDENTIFIER  

wanT3E3StatsDropEvents 1.3.6.1.4.1.11.2.3.7.6.1.5.1.8.1.1.4.1.3
The total number of events in which frames were dropped by the probe due to lack of resources. Note that this number is not necessarily the number of frames dropped; it is just the number of times this condition has been detected.
OBJECT-TYPE    
  Counter64  

wanT3E3StatsInFrames 1.3.6.1.4.1.11.2.3.7.6.1.5.1.8.1.1.4.1.4
The total number of frames seen originating from the far end of the link including errored frames.
OBJECT-TYPE    
  Counter64  

wanT3E3StatsOutFrames 1.3.6.1.4.1.11.2.3.7.6.1.5.1.8.1.1.4.1.5
The total number of frames seen originating from the near end of the link including errored frames.
OBJECT-TYPE    
  Counter64  

wanT3E3StatsInOctets 1.3.6.1.4.1.11.2.3.7.6.1.5.1.8.1.1.4.1.6
The sum of octets from all frames seen originating from the far end of the link including errored frames.
OBJECT-TYPE    
  Counter64  

wanT3E3StatsOutOctets 1.3.6.1.4.1.11.2.3.7.6.1.5.1.8.1.1.4.1.7
The sum of octets from all frames seen originating from the near end of the link including errored frames.
OBJECT-TYPE    
  Counter64  

wanT3E3StatsPESs 1.3.6.1.4.1.11.2.3.7.6.1.5.1.8.1.1.4.1.8
A PES is a second with one or more PCVs OR one or more Out of Frame defects OR a detected incoming AIS. This gauge is not incremented when UASs are counted.
OBJECT-TYPE    
  Counter64  

wanT3E3StatsPSESs 1.3.6.1.4.1.11.2.3.7.6.1.5.1.8.1.1.4.1.9
A PSES is a second with 44 or more PCVs OR one or more Out of Frame defects OR a detected incoming AIS. This gauge is not incremented when UASs are counted.
OBJECT-TYPE    
  Counter64  

wanT3E3StatsOOFs 1.3.6.1.4.1.11.2.3.7.6.1.5.1.8.1.1.4.1.10
A DS3 OOF defect is detected when any three or more errors in sixteen or fewer consecutive F-bits occur within a DS3 M-frame. An OOF defect may also be called a Severely Errored Frame (SEF) defect. An OOF defect is cleared when reframe occurs. A DS3 Loss of Frame (LOF) failure is declared when the DS3 OOF defect is consistent for 2 to 10 seconds. The DS3 OOF defect ends when reframe occurs. The DS3 LOF failure is cleared when the DS3 OOF defect is absent for 10 to 20 seconds. An E3 OOF defect is detected when four consecutive frame alignment signals have been incorrectly received in there predicted positions in an E3 signal. E3 frame alignment occurs when the presence of three consecutive frame alignment signals have been detected.
OBJECT-TYPE    
  Counter64  

wanT3E3StatsSEFSs 1.3.6.1.4.1.11.2.3.7.6.1.5.1.8.1.1.4.1.11
A SEFS is a second with one or more Out of Frame defects OR a detected incoming AIS.
OBJECT-TYPE    
  Counter64  

wanT3E3StatsUASs 1.3.6.1.4.1.11.2.3.7.6.1.5.1.8.1.1.4.1.12
UAS are calculated by counting the number of seconds that the interface is unavailable. The DS3 interface is said to be unavailable from the onset of 10 contiguous PSESs, or the onset of the condition leading to a failure (see Failure States). If the condition leading to the failure was immediately preceded by one or more contiguous PSESs, then the DS3 interface unavailability starts from the onset of these PSESs. Once unavailable, and if no failure is present, the DS3 interface becomes available at the onset of 10 contiguous seconds with no PSESs. Once unavailable, and if a failure is present, the DS3 interface becomes available at the onset of 10 contiguous seconds with no PSESs, if the failure clearing time is less than or equal to 10 seconds. If the failure clearing time is more than 10 seconds, the DS3 interface becomes available at the onset of 10 contiguous seconds with no PSESs, or the onset period leading to the successful clearing condition, whichever occurs later. With respect to the DS3 error counts, all counters are incremented while the DS3 interface is deemed available. While the interface is deemed unavailable, the only count that is incremented is UASs.
OBJECT-TYPE    
  Counter64  

wanT3E3StatsLCVs 1.3.6.1.4.1.11.2.3.7.6.1.5.1.8.1.1.4.1.13
This parameter is a count of both BPVs and EXZs occurring over the accumulation period. An EXZ increments the LCV by one regardless of the length of the zero string.
OBJECT-TYPE    
  Counter64  

wanT3E3StatsPCVs 1.3.6.1.4.1.11.2.3.7.6.1.5.1.8.1.1.4.1.14
For all DS3 applications, a coding violation error event is a P-bit Parity Error event. A P-bit Parity Error event is the occurrence of a received P-bit code on the DS3 M-frame that is not identical to the corresponding locally- calculated code.
OBJECT-TYPE    
  Counter64  

wanT3E3StatsLESs 1.3.6.1.4.1.11.2.3.7.6.1.5.1.8.1.1.4.1.15
A Line Errored Second is a second in which one or more CVs occurred OR one or more LOS defects.
OBJECT-TYPE    
  Counter64  

wanT3E3StatsCCVs 1.3.6.1.4.1.11.2.3.7.6.1.5.1.8.1.1.4.1.16
For C-bit Parity and SYNTRAN DS3 applications, this is the count of coding violations reported via the C-bits. For C-bit Parity, it is a count of CP-bit parity errors occurring in the accumulation interval. For SYNTRAN, it is a count of CRC-9 errors occurring in the accumulation interval.
OBJECT-TYPE    
  Counter64  

wanT3E3StatsCESs 1.3.6.1.4.1.11.2.3.7.6.1.5.1.8.1.1.4.1.17
An CES is a second with one or more CCVs OR one or more Out of Frame defects OR a detected incoming AIS. This count is only for the SYNTRAN and C-bit Parity DS3 applications. This gauge is not incremented when UASs are counted.
OBJECT-TYPE    
  Counter64  

wanT3E3StatsCSESs 1.3.6.1.4.1.11.2.3.7.6.1.5.1.8.1.1.4.1.18
A CSES is a second with 44 or more CCVs OR one or more Out of Frame defects OR a detected incoming AIS. This count is only for the SYNTRAN and C-bit Parity DS3 applications. This gauge is not incremented when UASs are counted.
OBJECT-TYPE    
  Counter64  

wanT3E3StatsRAIs 1.3.6.1.4.1.11.2.3.7.6.1.5.1.8.1.1.4.1.19
The Remote Alarm Indication (RAI) failure, in SYNTRAN applications, is declared after detecting the Yellow Alarm Signal on the alarm channel. See ANSI T1.107a-1990 [10]. The Remote Alarm Indication failure, in C-bit Parity DS3 applications, is declared as soon as the preqsence of either one or two alarm signals are detected on then Far End Alarm Channel. See [10]. The Remote Alarm Indication failure may also be declared after detecting the far-end SEF/AIS defect (aka yellow). The Remote Alarm Indication failure is cleared as soon as the presence of the any of the above alarms are removed. Also, the incoming failure state is declared when a defect persists for at least 2-10 seconds. The defects are the following: Loss of Signal (LOS), an Out of Frame (OOF) or an incoming Alarm Indication Signal (AIS). The Failure State is cleared when the defect is absent for less than or equal to 20 seconds.
OBJECT-TYPE    
  Counter64  

wanT3E3StatsAISs 1.3.6.1.4.1.11.2.3.7.6.1.5.1.8.1.1.4.1.20
The DS3 AIS is framed with 'stuck stuffing.' This implies that it has a valid M-subframe alignments bits, M-frame alignment bits, and P bits. The information bits are set to a 1010... sequence, starting with a one (1) after each M-subframe alignment bit, M-frame alignment bit, X bit, P bit, and C bit. The C bits are all set to zero giving what is called 'stuck stuffing.' The X bits are set to one. The DS3 AIS defect is declared after DS3 AIS is present in contiguous M-frames for a time equal to or greater than T, where 0.2 ms <= T <= 100 ms. The DS3 AIS defect is terminated after AIS is absent in contiguous M-frames for a time equal to or greater than T. The E3 binary content of the AIS is nominally a continuous stream of ones. AIS detection and the application of consequent actions, should be completed within a time limit of 1 ms.
OBJECT-TYPE    
  Counter64  

wanT3E3StatsLOFs 1.3.6.1.4.1.11.2.3.7.6.1.5.1.8.1.1.4.1.21
A DS3 Loss of Frame (LOF) failure is declared when the DS3 OOF defect is consistent for 2 to 10 seconds. The DS3 OOF defect ends when reframe occurs. The DS3 LOF failure is cleared when the DS3 OOF defect is absent for 10 to 20 seconds. (See T1.231 section 7.1.2.2.1)
OBJECT-TYPE    
  Counter64  

wanT3E3StatsLOSs 1.3.6.1.4.1.11.2.3.7.6.1.5.1.8.1.1.4.1.22
The DS3 LOS defect is declared upon observing 175 +/- 75 contiguous pulse positions with no pulses of either positive or negative polarity. The DS3 LOS defect is terminated upon observing an average pulse density of at least 33% over a period of 175 +/- 75 contiguous pulse positions starting with the receipt of a pulse.
OBJECT-TYPE    
  Counter64  

wanT3E3StatsOwner 1.3.6.1.4.1.11.2.3.7.6.1.5.1.8.1.1.4.1.23
The entity that configured this entry.
OBJECT-TYPE    
  OwnerString  

wanT3E3StatsStatus 1.3.6.1.4.1.11.2.3.7.6.1.5.1.8.1.1.4.1.24
The status of this wanT3E3StatsTable entry.
OBJECT-TYPE    
  RowStatus  

wanT3E3HistoryTable 1.3.6.1.4.1.11.2.3.7.6.1.5.1.8.2.1.4
T3/E3 signaling statistics
OBJECT-TYPE    
  SEQUENCE OF  
    WanT3E3HistoryEntry

wanT3E3HistoryEntry 1.3.6.1.4.1.11.2.3.7.6.1.5.1.8.2.1.4.1
Statistics for a T3/E3 interface. The near end of the link refers to the side of the link that the probe is monitoring. The far end is the side the probe is not on.
OBJECT-TYPE    
  WanT3E3HistoryEntry  

wanT3E3HistoryIndex 1.3.6.1.4.1.11.2.3.7.6.1.5.1.8.2.1.4.1.1
The history of which this entry is a port. The history identified by a particular value of this index is the same history as identified by the same value of historyControlIndex.
OBJECT-TYPE    
  INTEGER 1..65535  

wanT3E3HistorySampleIndex 1.3.6.1.4.1.11.2.3.7.6.1.5.1.8.2.1.4.1.2
An index that uniquely identifies the particular sample this entry represents among all samples associated with the same historyControlEntry. This index starts at 1 and increases by one as each new sample is taken.
OBJECT-TYPE    
  INTEGER 1..2147483647  

wanT3E3HistoryIntervalStart 1.3.6.1.4.1.11.2.3.7.6.1.5.1.8.2.1.4.1.3
The value of sysUpTime at the start of the interval over which this sample was measured. If the probe keeps track of time of day, it should start the first sample of the history at a time such that when the next hour of the day begins, a sample is started at that instant. Note that following this rule may require the probe to delay collection the first sample of the history, as each sample must be of the same interval. Also note that the sample which is currently being collected is not accessible in this table until the end of its interval.
OBJECT-TYPE    
  TimeTicks  

wanT3E3HistoryDropEvents 1.3.6.1.4.1.11.2.3.7.6.1.5.1.8.2.1.4.1.4
The change in value of wanT3E3StatsDropEvents during the interval.
OBJECT-TYPE    
  Counter64  

wanT3E3HistoryInFrames 1.3.6.1.4.1.11.2.3.7.6.1.5.1.8.2.1.4.1.5
The change in value of wanT3E3StatsInFrames during the interval.
OBJECT-TYPE    
  Counter64  

wanT3E3HistoryOutFrames 1.3.6.1.4.1.11.2.3.7.6.1.5.1.8.2.1.4.1.6
The change in value of wanT3E3StatsOutFrames during the interval.
OBJECT-TYPE    
  Counter64  

wanT3E3HistoryInOctets 1.3.6.1.4.1.11.2.3.7.6.1.5.1.8.2.1.4.1.7
The change in value of wanT3E3StatsInOctets during the interval.
OBJECT-TYPE    
  Counter64  

wanT3E3HistoryOutOctets 1.3.6.1.4.1.11.2.3.7.6.1.5.1.8.2.1.4.1.8
The change in value of wanT3E3StatsOutOctets during the interval.
OBJECT-TYPE    
  Counter64  

wanT3E3HistoryPESs 1.3.6.1.4.1.11.2.3.7.6.1.5.1.8.2.1.4.1.9
The change in value of wanT3E3StatsPESs during the interval.
OBJECT-TYPE    
  Counter64  

wanT3E3HistoryPSESs 1.3.6.1.4.1.11.2.3.7.6.1.5.1.8.2.1.4.1.10
The change in value of wanT3E3StatsPSESs during the interval.
OBJECT-TYPE    
  Counter64  

wanT3E3HistoryOOFs 1.3.6.1.4.1.11.2.3.7.6.1.5.1.8.2.1.4.1.11
The change in value of wanT3E3StatsOOFs during the interval.
OBJECT-TYPE    
  Counter64  

wanT3E3HistorySEFSs 1.3.6.1.4.1.11.2.3.7.6.1.5.1.8.2.1.4.1.12
The change in value of wanT3E3StatsSEFs during the interval.
OBJECT-TYPE    
  Counter64  

wanT3E3HistoryUASs 1.3.6.1.4.1.11.2.3.7.6.1.5.1.8.2.1.4.1.13
The change in value of wanT3E3StatsUASs during the interval.
OBJECT-TYPE    
  Counter64  

wanT3E3HistoryLCVs 1.3.6.1.4.1.11.2.3.7.6.1.5.1.8.2.1.4.1.14
The change in value of wanT3E3StatsLCVs during the interval.
OBJECT-TYPE    
  Counter64  

wanT3E3HistoryPCVs 1.3.6.1.4.1.11.2.3.7.6.1.5.1.8.2.1.4.1.15
The change in value of wanT3E3StatsPCVs during the interval.
OBJECT-TYPE    
  Counter64  

wanT3E3HistoryLESs 1.3.6.1.4.1.11.2.3.7.6.1.5.1.8.2.1.4.1.16
The change in value of wanT3E3StatsLESs during the interval.
OBJECT-TYPE    
  Counter64  

wanT3E3HistoryCCVs 1.3.6.1.4.1.11.2.3.7.6.1.5.1.8.2.1.4.1.17
The change in value of wanT3E3StatsCCVs during the interval.
OBJECT-TYPE    
  Counter64  

wanT3E3HistoryCESs 1.3.6.1.4.1.11.2.3.7.6.1.5.1.8.2.1.4.1.18
The change in value of wanT3E3StatsCESs during the interval.
OBJECT-TYPE    
  Counter64  

wanT3E3HistoryCSESs 1.3.6.1.4.1.11.2.3.7.6.1.5.1.8.2.1.4.1.19
The change in value of wanT3E3StatsCSESs during the interval.
OBJECT-TYPE    
  Counter64  

wanT3E3HistoryRAIs 1.3.6.1.4.1.11.2.3.7.6.1.5.1.8.2.1.4.1.20
The change in value of wanT3E3StatsRAIs during the interval.
OBJECT-TYPE    
  Counter64  

wanT3E3HistoryAISs 1.3.6.1.4.1.11.2.3.7.6.1.5.1.8.2.1.4.1.21
The change in value of wanT3E3StatsAISs during the interval.
OBJECT-TYPE    
  Counter64  

wanT3E3HistoryLOFs 1.3.6.1.4.1.11.2.3.7.6.1.5.1.8.2.1.4.1.22
The change in value of wanT3E3StatsLOFs during the interval.
OBJECT-TYPE    
  Counter64  

wanT3E3HistoryLOSs 1.3.6.1.4.1.11.2.3.7.6.1.5.1.8.2.1.4.1.23
The change in value of wanT3E3StatsLOSs during the interval.
OBJECT-TYPE    
  Counter64  

wanT3E3HistoryInUtilization 1.3.6.1.4.1.11.2.3.7.6.1.5.1.8.2.1.4.1.24
The best estimated of the mean physical layer network utilization of traffic coming from the far end of the link in hundreds of a percent.
OBJECT-TYPE    
  INTEGER 0..10000  

wanT3E3HistoryOutUtilization 1.3.6.1.4.1.11.2.3.7.6.1.5.1.8.2.1.4.1.25
The best estimated of the mean physical layer network utilization of traffic coming from the near end of the link in hundreds of a percent.
OBJECT-TYPE    
  INTEGER 0..10000  

wanAtmStatsTable 1.3.6.1.4.1.11.2.3.7.6.1.5.1.8.1.1.5
ATM signaling statistics.
OBJECT-TYPE    
  SEQUENCE OF  
    WanAtmStatsEntry

wanAtmStatsEntry 1.3.6.1.4.1.11.2.3.7.6.1.5.1.8.1.1.5.1
The statistics for an ATM interface. The near end of the link refers to the side of the link that the probe is monitoring. The far end is the side the probe is not on. In an ATM network, there are many far ends of the link, but they shall be logically grouped into one end in this table.
OBJECT-TYPE    
  WanAtmStatsEntry  

wanAtmStatsIndex 1.3.6.1.4.1.11.2.3.7.6.1.5.1.8.1.1.5.1.1
The value of this object uniquely identifies this wanAtmStatsTable entry.
OBJECT-TYPE    
  INTEGER 1..65535  

wanAtmStatsDataSource 1.3.6.1.4.1.11.2.3.7.6.1.5.1.8.1.1.5.1.2
This object identifies the source of the data that this wanAtmStatsEntry analyzes. This source can be any interface on this device. in order to identify a particular interface, this object shall identify the instance of the ifIndex object, defined in MIB-II [RFC 1573] for the desired interface. The ifType value associated with the ifIndex can only be atm(37).
OBJECT-TYPE    
  OBJECT IDENTIFIER  

wanAtmStatsDropEvents 1.3.6.1.4.1.11.2.3.7.6.1.5.1.8.1.1.5.1.3
The total number of events in which frames were dropped by the probe due to lack of resources. Note that this number is not necessarily the number of frames dropped; it is just the number of times this condition has been detected.
OBJECT-TYPE    
  Counter64  

wanAtmStatsInCells 1.3.6.1.4.1.11.2.3.7.6.1.5.1.8.1.1.5.1.4
The total number of cells seen coming from the far end of the link including errored cells.
OBJECT-TYPE    
  Counter64  

wanAtmStatsOutCells 1.3.6.1.4.1.11.2.3.7.6.1.5.1.8.1.1.5.1.5
The total number of cells seen coming from the near end of the link including errored cells.
OBJECT-TYPE    
  Counter64  

wanAtmStatsInCLP1 1.3.6.1.4.1.11.2.3.7.6.1.5.1.8.1.1.5.1.6
The total number of cells with the CLP bit set seen coming from the far end of the link.
OBJECT-TYPE    
  Counter64  

wanAtmStatsOutCLP1 1.3.6.1.4.1.11.2.3.7.6.1.5.1.8.1.1.5.1.7
The total number of cells with the CLP bit set seen coming from the near end of the link.
OBJECT-TYPE    
  Counter64  

wanAtmStatsConnectionEvents 1.3.6.1.4.1.11.2.3.7.6.1.5.1.8.1.1.5.1.8
This counter counts the sum of the following errors: 1) SSCOP Connection Disconnect Counter The abnormal occurrence of this event is characterized by the expiry of Timer_NO_RESPONSE. (This event is communicated to the layer management with MAA-ERROR code P. See ITU-T Q.2110.) 2) SSCOP Connection Initiation Failure This condition indicates the inability to establish an SSCOP connection. This event occurs whenever the number of expiries of the connection control timer (Timer_CC) exceeds the MaxCC or upon receipt of a connection reject message BGREJ PDU. (This event is communicated to layer management with MAA-ERROR code O. See ITU-T Q.2110.) 3) SSCOP Connection Re-Establ/Resynch This event occurs upon receipt of a BGN PDU or RESYNC PDU.
OBJECT-TYPE    
  Counter64  

wanAtmStatsErroredPDUs 1.3.6.1.4.1.11.2.3.7.6.1.5.1.8.1.1.5.1.9
This counter counts the sum of the following errors: 1) Invalid PDUs. These are defined in SSCOP and consist of PDUs with incorrect length (MAA-ERROR code U), undefined PDU type code or not 32-bit aligned. 2) PDUs that result in MAA error codes and are discarded See Errors A-M and Q-T defined in ITU-T Q.2110.
OBJECT-TYPE    
  Counter64  

wanAtmStatsSetupAttempts 1.3.6.1.4.1.11.2.3.7.6.1.5.1.8.1.1.5.1.10
This counter counts the number of call setup attempts (both successful and unsuccessful) detected on this interface.
OBJECT-TYPE    
  Counter64  

wanAtmStatsInRoutesUnavailable 1.3.6.1.4.1.11.2.3.7.6.1.5.1.8.1.1.5.1.11
This counter is incremented when a RELEASE, RELEASE COMPLETE (only when not preceded by a RELEASE mesg for the same call), ADD PARTY REJECT, or STATUS message that contains one of the following cause code values is received (Note: These cause values apply to both UNI3.0 and UNI3.1): Cause Value Meaning 1 unallocated (unassigned) number 2 no route to specified transit network 3 no route to destination 88 incompatible destination NOTE: For this counter, RELEASE COMPLETE messages that are a reply to a previous RELEASE message and contain the same cause value, are redundant (for counting purposes) and should not be counted.
OBJECT-TYPE    
  Counter64  

wanAtmStatsOutRoutesUnavailable 1.3.6.1.4.1.11.2.3.7.6.1.5.1.8.1.1.5.1.12
This counter is incremented when a RELEASE, RELEASE COMPLETE (only when not preceded by a RELEASE mesg for the same call), ADD PARTY REJECT, or STATUS message that contains one of the following cause code values is transmitted (Note: These cause values apply to both UNI3.0 and UNI3.1): Cause Value Meaning 1 unallocated (unassigned) number 2 no route to specified transit network 3 no route to destination NOTE: For this counter, RELEASE COMPLETE messages that are a reply to a previous RELEASE message and contain the same cause value, are redundant(for counting purposes) and should not be counted.
OBJECT-TYPE    
  Counter64  

wanAtmStatsInResourcesUnavailable 1.3.6.1.4.1.11.2.3.7.6.1.5.1.8.1.1.5.1.13
This counter is incremented when a RELEASE, RELEASE COMPLETE (only when not preceded by a RELEASE mesg for the same call), ADD PARTY REJECT, or STATUS message that contains one of the following cause code values is received (Note: These cause values apply to both UNI3.0 and UNI3.1 unless otherwise stated): Cause Value Meaning 35 requested VPCI/VCI not available 37 user cell rate not available (UNI3.1 only) 38 network out of order 41 temporary failure 45 no VPCI/VCI available 47 resource unavailable, unspecified 49 Quality of Service unavailable 51 user cell rate not available (UNI3.0 only) 58 bearer capability not presently available 63 Service or option not available, unspecified 92 too many pending add party requests NOTE: For this counter, RELEASE COMPLETE messages that are a reply to a previous RELEASE message and contain the same cause value, are redundant (for counting purposes) and should not be counted.
OBJECT-TYPE    
  Counter64  

wanAtmStatsOutResourcesUnavailable 1.3.6.1.4.1.11.2.3.7.6.1.5.1.8.1.1.5.1.14
This counter is incremented when a RELEASE, RELEASE COMPLETE (only when not preceded by a RELEASE mesg for the same call), ADD PARTY REJECT, or STATUS message that contains one of the following cause code values is transmitted (Note: These cause values apply to both UNI3.0 and UNI3.1 unless otherwise stated): Cause Value Meaning 35 requested VPCI/VCI not available 37 user cell rate not available (UNI3.1 only) 38 network out of order 41 temporary failure 45 no VPCI/VCI available 47 resource unavailable, unspecified 49 Quality of Service unavailable 51 user cell rate not available (UNI3.0 only) 58 bearer capability not presently available 63 Service or option not available, unspecified 92 too many pending add party requests NOTE: For this counter, RELEASE COMPLETE messages that are a reply to a previous RELEASE message and contain the same cause value, are redundant (for counting purposes) and should not be counted.
OBJECT-TYPE    
  Counter64  

wanAtmStatsInUnsuccessfulCalls 1.3.6.1.4.1.11.2.3.7.6.1.5.1.8.1.1.5.1.15
This counter is incremented when a RELEASE, RELEASE COMPLETE (only when not preceded by a RELEASE mesg for the same call), ADD PARTY REJECT, or STATUS message that contains one of the following cause code values is received (Note: These cause values apply to both UNI3.0 and UNI3.1): Cause Value Meaning 17 user busy 18 no user responding 21 call rejected 22 number changed 23 user rejects all calls with calling line id restriction 27 destination out of order 31 normal, unspecified 88 incompatible destination NOTE: For this counter, RELEASE COMPLETE messages that are a reply to a previous RELEASE message and contain the same cause value, are redundant (for counting purposes) and should not be counted. Note: Cause Value #30 'response to STATUS ENQUIRY' was not included in this memo since it did not apply to a hard failure.
OBJECT-TYPE    
  Counter64  

wanAtmStatsOutUnsuccessfulCalls 1.3.6.1.4.1.11.2.3.7.6.1.5.1.8.1.1.5.1.16
This counter is incremented when a RELEASE, RELEASE COMPLETE (only when not preceded by a RELEASE mesg for the same call), ADD PARTY REJECT, or STATUS message that contains one of the following cause code values is transmitted (Note: These cause values apply to both UNI3.0 and UNI3.1): Cause Value Meaning 17 user busy 18 no user responding 21 call rejected 22 number changed 23 user rejects all calls with calling line id restriction (CLIR) 27 destination out of order 31 normal, unspecified 88 incompatible destination NOTE: For this counter, RELEASE COMPLETE messages that are a reply to a previous RELEASE message and contain the same cause value, are redundant(for counting purposes) and should not be counted. Note: Cause Value #30 'response to STATUS ENQUIRY' was not included in this memo since it did not apply to a hard failure.
OBJECT-TYPE    
  Counter64  

wanAtmStatsInIncorrectMsgs 1.3.6.1.4.1.11.2.3.7.6.1.5.1.8.1.1.5.1.17
The Incorrect Messages Counter reflects any sort of incorrect information in a message. This includes: ? RELEASE, RELEASE COMPLETE, ADD PARTY REJECT, and STATUS messages transmitted or received, that contain any of the Cause values listed below. ? Ignored messages. These messages are dropped because the message was so damaged that it could not be further processed. A list of dropped messages is compiled below: Message with invalid protocol discriminator Message with errors in the call reference I.E. ? Bits 5-8 of the first octet not equal to '0000' ? Bits 1-4 of the first octet indicating a length other than 3 octets ? RELEASE COMPLETE message received with a call reference that does not relate to a call active or in progress ? SETUP message received with call reference flag incorrectly set to 1 ? SETUP message received with a call reference for a call that is already active or in progress. Message too short The following cause values are monitored by this counter (Note: These cause values apply to both UNI3.0 and UNI3.1 unless otherwise stated) Cause Value Meaning 10 VPCI/VCI unacceptable (UNI3.0 only) 36 VPCI/VCI assignment failure (UNI3.1 only) 81 invalid call reference value 82 identified channel does not exist 89 invalid endpoint reference 96 mandatory information element is missing 97 message type non-existent or not implemented 99 information element non-existent or not implemented 100 invalid information element contents 101 message not compatible with call state 104 incorrect message length 111 protocol error, unspecified NOTE: For this counter, RELEASE COMPLETE messages that are a reply to a previous RELEASE message and contain the same cause value, are redundant (for counting purposes) and should not be counted.
OBJECT-TYPE    
  Counter64  

wanAtmStatsOutIncorrectMsgs 1.3.6.1.4.1.11.2.3.7.6.1.5.1.8.1.1.5.1.18
The Incorrect Messages Counter reflects any sort of incorrect information in a message. This includes: ? RELEASE, RELEASE COMPLETE, ADD PARTY REJECT, and STATUS messages transmitted or received, that contain any of the Cause values listed below. ? Ignored messages. These messages are dropped because the message was so damaged that it could not be further processed. A list of dropped messages is compiled below: Message with invalid protocol discriminator Message with errors in the call reference I.E. ? Bits 5-8 of the first octet not equal to '0000' ? Bits 1-4 of the first octet indicating a length other than 3 octets ? RELEASE COMPLETE message received with a call reference that does not relate to a call active or in progress ? SETUP message received with call reference flag incorrectly set to 1 ? SETUP message received with a call reference for a call that is already active or in progress. Message too short The following cause values are monitored by this counter Note: These cause values apply to both UNI3.0 and UNI3.1 unless otherwise stated) Cause Value Meaning 10 VPCI/VCI unacceptable (UNI3.0 only) 36 VPCI/VCI assignment failure (UNI3.1 only) 81 invalid call reference value 82 identified channel does not exist 89 invalid endpoint reference 96 mandatory information element is missing 97 message type non-existent or not implemented 99 information element non-existent or not implemented 100 invalid information element contents 101 message not compatible with call state 104 incorrect message length 111 protocol error, unspecified NOTE: For this counter, RELEASE COMPLETE messages that are a reply to a previous RELEASE message and contain the same cause value, are redundant (for counting purposes) and should not be counted.
OBJECT-TYPE    
  Counter64  

wanAtmStatsInPartyEvents 1.3.6.1.4.1.11.2.3.7.6.1.5.1.8.1.1.5.1.19
This counter monitors error events that occur due to the originating user doing something wrong. This counter is incremented when a RELEASE, RELEASE COMPLETE (only when not preceded by a RELEASE mesg for the same call), ADD PARTY REJECT, or STATUS message that contains one of the following cause code values is received (Note: These cause values apply to both UNI3.0 and UNI3.1): Cause Value Meaning 28 invalid number format (address incomplete) 43 access information discarded 57 bearer capability not authorized 65 bearer capability not implemented 73 unsupported combination of traffic parameters 78 AAL parameters cannot be supported (UNI3.1 only) 91 invalid transit network selection 93 AAL parameters cannot be supported (UNI3.0 only) NOTE: For this counter, RELEASE COMPLETE messages that are a reply to a previous RELEASE message and contain the same cause value, are redundant(for counting purposes) and should not be counted.
OBJECT-TYPE    
  Counter64  

wanAtmStatsOutPartyEvents 1.3.6.1.4.1.11.2.3.7.6.1.5.1.8.1.1.5.1.20
This counter monitors error events that occur due to the originating user doing something wrong. This counter is incremented when a RELEASE, RELEASE COMPLETE (only when not preceded by a RELEASE mesg for the same call), ADD PARTY REJECT, or STATUS message that contains one of the following cause code values is transmitted (Note: These cause values apply to both UNI3.0 and UNI3.1): Cause Value Meaning 28 invalid number format (address incomplete) 43 access information discarded 57 bearer capability not authorized 65 bearer capability not implemented 73 unsupported combination of traffic parameters 78 AAL parameters cannot be supported (UNI3.1 only) 91 invalid transit network selection 93 AAL parameters cannot be supported (UNI3.0 only) NOTE: For this counter, RELEASE COMPLETE messages that are a reply to a previous RELEASE message and contain the same cause value, are redundant (for counting purposes) and should not be counted.
OBJECT-TYPE    
  Counter64  

wanAtmStatsInExpiries 1.3.6.1.4.1.11.2.3.7.6.1.5.1.8.1.1.5.1.21
The Timer Expiries Counter provides a count of network timer expiries, and to some extent, host or switch timer expiries. The conditions for incrementing this counter are: ? Expiry of any network timer ? Receipt of a RELEASE or RELEASE COMPLETE message with Cause #102, 'recovery on timer expiry'. NOTE: For this counter, RELEASE COMPLETE messages that are a reply to a previous RELEASE message and contain the same cause value, are redundant (for counting purposes) and should not be counted.
OBJECT-TYPE    
  Counter64  

wanAtmStatsOutExpiries 1.3.6.1.4.1.11.2.3.7.6.1.5.1.8.1.1.5.1.22
The Timer Expiries Counter provides a count of network timer expiries, and to some extent, host or switch timer expiries. The conditions for incrementing this counter are: ? Expiry of any network timer ? Receipt of a RELEASE or RELEASE COMPLETE message with Cause #102, 'recovery on timer expiry'. NOTE: For this counter, RELEASE COMPLETE messages that are a reply to a previous RELEASE message and contain the same cause value, are redundant (for counting purposes) and should not be counted.
OBJECT-TYPE    
  Counter64  

wanAtmStatsInRestartErrors 1.3.6.1.4.1.11.2.3.7.6.1.5.1.8.1.1.5.1.23
The Restart Activity Counter provides a count of host, switch, or network restart activity. This counter is incremented when receiving a RESTART message.
OBJECT-TYPE    
  Counter64  

wanAtmStatsOutRestartErrors 1.3.6.1.4.1.11.2.3.7.6.1.5.1.8.1.1.5.1.24
The Restart Activity Counter provides a count of host, switch, or network restart activity. This counter is incremented when transmitting a RESTART message.
OBJECT-TYPE    
  Counter64  

wanAtmStatsInSVCs 1.3.6.1.4.1.11.2.3.7.6.1.5.1.8.1.1.5.1.25
SVC VCCs established at this signaling entity for incoming connections.
OBJECT-TYPE    
  Counter64  

wanAtmStatsOutSVCs 1.3.6.1.4.1.11.2.3.7.6.1.5.1.8.1.1.5.1.26
SVC VCCs established at this signaling entity for outgoing connections.
OBJECT-TYPE    
  Counter64  

wanAtmStatsInOCDs 1.3.6.1.4.1.11.2.3.7.6.1.5.1.8.1.1.5.1.27
An out of cell delineation from far end of the link.
OBJECT-TYPE    
  Counter64  

wanAtmStatsOutOCDs 1.3.6.1.4.1.11.2.3.7.6.1.5.1.8.1.1.5.1.28
An out of cell delineation from near end of the link.
OBJECT-TYPE    
  Counter64  

wanAtmStatsInLOCs 1.3.6.1.4.1.11.2.3.7.6.1.5.1.8.1.1.5.1.29
A loss of cell delineation error from far end of the link. This is a persistent OCD condition.
OBJECT-TYPE    
  Counter64  

wanAtmStatsOutLOCs 1.3.6.1.4.1.11.2.3.7.6.1.5.1.8.1.1.5.1.30
A loss of cell delineation error from near end of link. This is a persistent OCD condition.
OBJECT-TYPE    
  Counter64  

wanAtmStatsInLOFs 1.3.6.1.4.1.11.2.3.7.6.1.5.1.8.1.1.5.1.31
A loss of frame error from far end of link.
OBJECT-TYPE    
  Counter64  

wanAtmStatsOutLOFs 1.3.6.1.4.1.11.2.3.7.6.1.5.1.8.1.1.5.1.32
A loss of frame error from near end of link.
OBJECT-TYPE    
  Counter64  

wanAtmStatsInLOPs 1.3.6.1.4.1.11.2.3.7.6.1.5.1.8.1.1.5.1.33
A loss of pointer error from far end of link.
OBJECT-TYPE    
  Counter64  

wanAtmStatsOutLOPs 1.3.6.1.4.1.11.2.3.7.6.1.5.1.8.1.1.5.1.34
A loss of pointer error from near end of link.
OBJECT-TYPE    
  Counter64  

wanAtmStatsInLOSs 1.3.6.1.4.1.11.2.3.7.6.1.5.1.8.1.1.5.1.35
A loss of signal error from far end of link.
OBJECT-TYPE    
  Counter64  

wanAtmStatsOutLOSs 1.3.6.1.4.1.11.2.3.7.6.1.5.1.8.1.1.5.1.36
A loss of signal error from near end of link.
OBJECT-TYPE    
  Counter64  

wanAtmStatsOwner 1.3.6.1.4.1.11.2.3.7.6.1.5.1.8.1.1.5.1.37
The entity that configured this entry.
OBJECT-TYPE    
  OwnerString  

wanAtmStatsStatus 1.3.6.1.4.1.11.2.3.7.6.1.5.1.8.1.1.5.1.38
The status of this wanAtmStatsTable entry.
OBJECT-TYPE    
  RowStatus  

wanAtmHistoryTable 1.3.6.1.4.1.11.2.3.7.6.1.5.1.8.2.1.5
ATM signaling statistics.
OBJECT-TYPE    
  SEQUENCE OF  
    WanAtmHistoryEntry

wanAtmHistoryEntry 1.3.6.1.4.1.11.2.3.7.6.1.5.1.8.2.1.5.1
The statistics for an ATM interface. The near end of the link refers to the side of the link that the probe is monitoring. The far end is the side the probe is not on. In an ATM network, there are many far ends of the link, but they shall be logically grouped into one end in this table.
OBJECT-TYPE    
  WanAtmHistoryEntry  

wanAtmHistoryIndex 1.3.6.1.4.1.11.2.3.7.6.1.5.1.8.2.1.5.1.1
The history of which this entry is a port. The history identified by a particular value of this index is the same history as identified by the same value of historyControlIndex.
OBJECT-TYPE    
  INTEGER 1..65535  

wanAtmHistorySampleIndex 1.3.6.1.4.1.11.2.3.7.6.1.5.1.8.2.1.5.1.2
An index that uniquely identifies the particular sample this entry represents among all samples associated with the same historyControlEntry. This index starts at 1 and increases by one as each new sample is taken.
OBJECT-TYPE    
  INTEGER 1..2147483647  

wanAtmHistoryIntervalStart 1.3.6.1.4.1.11.2.3.7.6.1.5.1.8.2.1.5.1.3
The value of sysUpTime at the start of the interval over which this sample was measured. If the probe keeps track of time of day, it should start the first sample of the history at a time such that when the next hour of the day begins, a sample is started at that instant. Note that following this rule may require the probe to delay collection the first sample of the history, as each sample must be of the same interval. Also note that the sample which is currently being collected is not accessible in this table until the end of its interval.
OBJECT-TYPE    
  TimeTicks  

wanAtmHistoryDropEvents 1.3.6.1.4.1.11.2.3.7.6.1.5.1.8.2.1.5.1.4
The change in value of wanAtmStatsDropEvents during the interval.
OBJECT-TYPE    
  Counter64  

wanAtmHistoryInCells 1.3.6.1.4.1.11.2.3.7.6.1.5.1.8.2.1.5.1.5
The change in value of wanAtmStatsInCells during the interval.
OBJECT-TYPE    
  Counter64  

wanAtmHistoryOutCells 1.3.6.1.4.1.11.2.3.7.6.1.5.1.8.2.1.5.1.6
The change in value of wanAtmStatsOutCells during the interval.
OBJECT-TYPE    
  Counter64  

wanAtmHistoryInCLP1 1.3.6.1.4.1.11.2.3.7.6.1.5.1.8.2.1.5.1.7
The change in value of wanAtmStatsInCLP1 during the interval.
OBJECT-TYPE    
  Counter64  

wanAtmHistoryOutCLP1 1.3.6.1.4.1.11.2.3.7.6.1.5.1.8.2.1.5.1.8
The change in value of wanAtmStatsOutCLP1 during the interval.
OBJECT-TYPE    
  Counter64  

wanAtmHistoryConnectionEvents 1.3.6.1.4.1.11.2.3.7.6.1.5.1.8.2.1.5.1.9
The change in value of wanAtmStatsConnectionEvents during the interval.
OBJECT-TYPE    
  Counter64  

wanAtmHistoryErroredPDUs 1.3.6.1.4.1.11.2.3.7.6.1.5.1.8.2.1.5.1.10
The change in value of wanAtmStatsErroredPDUs during the interval.
OBJECT-TYPE    
  Counter64  

wanAtmHistorySetupAttempts 1.3.6.1.4.1.11.2.3.7.6.1.5.1.8.2.1.5.1.11
The change in value of wanAtmStatsSetupAttempts during the interval.
OBJECT-TYPE    
  Counter64  

wanAtmHistoryInRoutesUnavailable 1.3.6.1.4.1.11.2.3.7.6.1.5.1.8.2.1.5.1.12
The change in value of wanAtmStatsInRoutesUnavailable during the interval.
OBJECT-TYPE    
  Counter64  

wanAtmHistoryOutRoutesUnavailable 1.3.6.1.4.1.11.2.3.7.6.1.5.1.8.2.1.5.1.13
The change in value of wanAtmStatsOutRoutesUnavailable during the interval.
OBJECT-TYPE    
  Counter64  

wanAtmHistoryInResourcesUnavailable 1.3.6.1.4.1.11.2.3.7.6.1.5.1.8.2.1.5.1.14
The change in value of wanAtmStatsInResourcesUnavailable during the interval.
OBJECT-TYPE    
  Counter64  

wanAtmHistoryOutResourcesUnavailable 1.3.6.1.4.1.11.2.3.7.6.1.5.1.8.2.1.5.1.15
The change in value of wanAtmStatsOutResourcesUnavailable during the interval.
OBJECT-TYPE    
  Counter64  

wanAtmHistoryInUnsuccessfulCalls 1.3.6.1.4.1.11.2.3.7.6.1.5.1.8.2.1.5.1.16
The change in value of wanAtmStatsInUnsuccessfulCalls during the interval.
OBJECT-TYPE    
  Counter64  

wanAtmHistoryOutUnsuccessfulCalls 1.3.6.1.4.1.11.2.3.7.6.1.5.1.8.2.1.5.1.17
The change in value of wanAtmStatsOutUnsuccessfulCalls during the interval.
OBJECT-TYPE    
  Counter64  

wanAtmHistoryInIncorrectMsgs 1.3.6.1.4.1.11.2.3.7.6.1.5.1.8.2.1.5.1.18
The change in value of wanAtmStatsInIncorrectMsgs during the interval.
OBJECT-TYPE    
  Counter64  

wanAtmHistoryOutIncorrectMsgs 1.3.6.1.4.1.11.2.3.7.6.1.5.1.8.2.1.5.1.19
The change in value of wanAtmStatsOutIncorrectMsgs during the interval.
OBJECT-TYPE    
  Counter64  

wanAtmHistoryInPartyEvents 1.3.6.1.4.1.11.2.3.7.6.1.5.1.8.2.1.5.1.20
The change in value of wanAtmStatsInPartyEvents during the interval.
OBJECT-TYPE    
  Counter64  

wanAtmHistoryOutPartyEvents 1.3.6.1.4.1.11.2.3.7.6.1.5.1.8.2.1.5.1.21
The change in value of wanAtmStatsOutPartyEvents during the interval.
OBJECT-TYPE    
  Counter64  

wanAtmHistoryInExpiries 1.3.6.1.4.1.11.2.3.7.6.1.5.1.8.2.1.5.1.22
The change in value of wanAtmStatsInExpiries during the interval.
OBJECT-TYPE    
  Counter64  

wanAtmHistoryOutExpiries 1.3.6.1.4.1.11.2.3.7.6.1.5.1.8.2.1.5.1.23
The change in value of wanAtmStatsOutExpiries during the interval.
OBJECT-TYPE    
  Counter64  

wanAtmHistoryInRestartErrors 1.3.6.1.4.1.11.2.3.7.6.1.5.1.8.2.1.5.1.24
The change in value of wanAtmStatsInRestartErrors during the interval.
OBJECT-TYPE    
  Counter64  

wanAtmHistoryOutRestartErrors 1.3.6.1.4.1.11.2.3.7.6.1.5.1.8.2.1.5.1.25
The change in value of wanAtmStatsOutRestartErrors during the interval.
OBJECT-TYPE    
  Counter64  

wanAtmHistoryInSVCs 1.3.6.1.4.1.11.2.3.7.6.1.5.1.8.2.1.5.1.26
The change in value of wanAtmStatsInSVCs during the interval.
OBJECT-TYPE    
  Counter64  

wanAtmHistoryOutSVCs 1.3.6.1.4.1.11.2.3.7.6.1.5.1.8.2.1.5.1.27
The change in value of wanAtmStatsOutSVCs during the interval.
OBJECT-TYPE    
  Counter64  

wanAtmHistoryInOCDs 1.3.6.1.4.1.11.2.3.7.6.1.5.1.8.2.1.5.1.28
The change in value of wanAtmStatsInOCDs during the interval.
OBJECT-TYPE    
  Counter64  

wanAtmHistoryOutOCDs 1.3.6.1.4.1.11.2.3.7.6.1.5.1.8.2.1.5.1.29
The change in value of wanAtmStatsOutOCDs during the interval.
OBJECT-TYPE    
  Counter64  

wanAtmHistoryInLOCs 1.3.6.1.4.1.11.2.3.7.6.1.5.1.8.2.1.5.1.30
The change in value of wanAtmStatsInLOCs during the interval.
OBJECT-TYPE    
  Counter64  

wanAtmHistoryOutLOCs 1.3.6.1.4.1.11.2.3.7.6.1.5.1.8.2.1.5.1.31
The change in value of wanAtmStatsOutLOCs during the interval.
OBJECT-TYPE    
  Counter64  

wanAtmHistoryInLOFs 1.3.6.1.4.1.11.2.3.7.6.1.5.1.8.2.1.5.1.32
The change in value of wanAtmStatsInLOFs during the interval.
OBJECT-TYPE    
  Counter64  

wanAtmHistoryOutLOFs 1.3.6.1.4.1.11.2.3.7.6.1.5.1.8.2.1.5.1.33
The change in value of wanAtmStatsOutLOFs during the interval.
OBJECT-TYPE    
  Counter64  

wanAtmHistoryInLOPs 1.3.6.1.4.1.11.2.3.7.6.1.5.1.8.2.1.5.1.34
The change in value of wanAtmStatsInLOPs during the interval.
OBJECT-TYPE    
  Counter64  

wanAtmHistoryOutLOPs 1.3.6.1.4.1.11.2.3.7.6.1.5.1.8.2.1.5.1.35
The change in value of wanAtmStatsOutLOPs during the interval.
OBJECT-TYPE    
  Counter64  

wanAtmHistoryInLOSs 1.3.6.1.4.1.11.2.3.7.6.1.5.1.8.2.1.5.1.36
The change in value of wanAtmStatsInLOSs during the interval.
OBJECT-TYPE    
  Counter64  

wanAtmHistoryOutLOSs 1.3.6.1.4.1.11.2.3.7.6.1.5.1.8.2.1.5.1.37
The change in value of wanAtmStatsOutLOSs during the interval.
OBJECT-TYPE    
  Counter64  

wanAtmHistoryInUtilization 1.3.6.1.4.1.11.2.3.7.6.1.5.1.8.2.1.5.1.38
The best estimated of the mean physical layer network utilization of traffic coming from the far end of the link in hundreds of a percent.
OBJECT-TYPE    
  INTEGER 0..10000  

wanAtmHistoryOutUtilization 1.3.6.1.4.1.11.2.3.7.6.1.5.1.8.2.1.5.1.39
The best estimated of the mean physical layer network utilization of traffic coming from the near end of the link in hundreds of a percent.
OBJECT-TYPE    
  INTEGER 0..10000  

wanX25StatsTable 1.3.6.1.4.1.11.2.3.7.6.1.5.1.8.1.2.1
X.25 Packet layer statistics.
OBJECT-TYPE    
  SEQUENCE OF  
    WanX25StatsEntry

wanX25StatsEntry 1.3.6.1.4.1.11.2.3.7.6.1.5.1.8.1.2.1.1
The statistics for an X.25 interface across all LCIs. The near end of the link refers to the side of the link that the probe is monitoring. The far end is the side the probe is not on. In an X.25 network, there are many far ends of the link, but they shall be logically grouped into one end in this table.
OBJECT-TYPE    
  WanX25StatsEntry  

wanX25StatsIndex 1.3.6.1.4.1.11.2.3.7.6.1.5.1.8.1.2.1.1.1
The value of this object uniquely identifies this wanX25StatsTable entry.
OBJECT-TYPE    
  INTEGER 1..65535  

wanX25StatsDataSource 1.3.6.1.4.1.11.2.3.7.6.1.5.1.8.1.2.1.1.2
This object identifies the source of the data that this wanX25StatsEntry analyzes. This source can be any interface on this device. In order to identify a particular interface, this object shall identify the instance of the ifIndex object, defined in MIB-II [RFC 1573] for the desired interface. The ifType value associated with the ifIndex can only be rfc887-x25(5).
OBJECT-TYPE    
  OBJECT IDENTIFIER  

wanX25StatsDropEvents 1.3.6.1.4.1.11.2.3.7.6.1.5.1.8.1.2.1.1.3
The total number of events in which frames were dropped by the probe due to lack of resources. Note that this number is not necessarily the number of frames dropped; it is just the number of times this condition has been detected.
OBJECT-TYPE    
  Counter64  

wanX25StatsInFrames 1.3.6.1.4.1.11.2.3.7.6.1.5.1.8.1.2.1.1.4
The total number of frames seen coming from the far end of the link including error packets.
OBJECT-TYPE    
  Counter64  

wanX25StatsOutFrames 1.3.6.1.4.1.11.2.3.7.6.1.5.1.8.1.2.1.1.5
The total number of frames seen coming from the near end of the link including error packets.
OBJECT-TYPE    
  Counter64  

wanX25StatsInOctets 1.3.6.1.4.1.11.2.3.7.6.1.5.1.8.1.2.1.1.6
The sum of octets from all frames seen originating from the far end of the link including errored frames.
OBJECT-TYPE    
  Counter64  

wanX25StatsOutOctets 1.3.6.1.4.1.11.2.3.7.6.1.5.1.8.1.2.1.1.7
The sum of octets from all frames seen originating from the near end of the link including errored frames.
OBJECT-TYPE    
  Counter64  

wanX25StatsInRejects 1.3.6.1.4.1.11.2.3.7.6.1.5.1.8.1.2.1.1.8
The number of REJ or SREJ frames see coming from the far end of the link.
OBJECT-TYPE    
  Counter64  

wanX25StatsOutRejects 1.3.6.1.4.1.11.2.3.7.6.1.5.1.8.1.2.1.1.9
The number of REJ or SREJ frames see coming from the near end of the link.
OBJECT-TYPE    
  Counter64  

wanX25StatsInAttempts 1.3.6.1.4.1.11.2.3.7.6.1.5.1.8.1.2.1.1.10
The number of call setup attempts initiated from the far end of the link.
OBJECT-TYPE    
  Counter64  

wanX25StatsOutAttempts 1.3.6.1.4.1.11.2.3.7.6.1.5.1.8.1.2.1.1.11
The number of call setup attempts initiated from the near end of the link.
OBJECT-TYPE    
  Counter64  

wanX25StatsInFailures 1.3.6.1.4.1.11.2.3.7.6.1.5.1.8.1.2.1.1.12
The number call setup attempt failures seen coming from the far end of the link.
OBJECT-TYPE    
  Counter64  

wanX25StatsOutFailures 1.3.6.1.4.1.11.2.3.7.6.1.5.1.8.1.2.1.1.13
The number call setup attempt failures seen coming from the near end of the link.
OBJECT-TYPE    
  Counter64  

wanX25StatsProviderClears 1.3.6.1.4.1.11.2.3.7.6.1.5.1.8.1.2.1.1.14
The number of clear request seen with a cause code other than DTE initiated.
OBJECT-TYPE    
  Counter64  

wanX25StatsInResets 1.3.6.1.4.1.11.2.3.7.6.1.5.1.8.1.2.1.1.15
The number of reset requests seen from the far end of the link with cause code DTE initiated.
OBJECT-TYPE    
  Counter64  

wanX25StatsOutResets 1.3.6.1.4.1.11.2.3.7.6.1.5.1.8.1.2.1.1.16
The number of reset requests seen from the near end of the link with cause code DTE initiated.
OBJECT-TYPE    
  Counter64  

wanX25StatsProviderResets 1.3.6.1.4.1.11.2.3.7.6.1.5.1.8.1.2.1.1.17
The number of reset requests seen with cause code other than DTE initiated.
OBJECT-TYPE    
  Counter64  

wanX25StatsInAccusedErrors 1.3.6.1.4.1.11.2.3.7.6.1.5.1.8.1.2.1.1.18
The numbers of packets seen from the far end of the link containing a procedure error cause code. These include clear, reset, restart, or diagnostic packets.
OBJECT-TYPE    
  Counter64  

wanX25StatsOutAccusedErrors 1.3.6.1.4.1.11.2.3.7.6.1.5.1.8.1.2.1.1.19
The numbers of packets seen from the near end of the link containing a procedure error cause code. These include clear, reset, restart, or diagnostic packets.
OBJECT-TYPE    
  Counter64  

wanX25StatsInInterrupts 1.3.6.1.4.1.11.2.3.7.6.1.5.1.8.1.2.1.1.20
The number of interrupts packets seen coming from the far end of the link over all VCs.
OBJECT-TYPE    
  Counter64  

wanX25StatsOutInterrupts 1.3.6.1.4.1.11.2.3.7.6.1.5.1.8.1.2.1.1.21
The number of interrupts packets seen coming from the near end of the link over all VCs.
OBJECT-TYPE    
  Counter64  

wanX25StatsOwner 1.3.6.1.4.1.11.2.3.7.6.1.5.1.8.1.2.1.1.22
The entity that configured this entry.
OBJECT-TYPE    
  OwnerString  

wanX25StatsStatus 1.3.6.1.4.1.11.2.3.7.6.1.5.1.8.1.2.1.1.23
The status of this wanX25StatsTable entry.
OBJECT-TYPE    
  RowStatus  

wanX25HistoryTable 1.3.6.1.4.1.11.2.3.7.6.1.5.1.8.2.2.1
X.25 Packet layer statistics.
OBJECT-TYPE    
  SEQUENCE OF  
    WanX25HistoryEntry

wanX25HistoryEntry 1.3.6.1.4.1.11.2.3.7.6.1.5.1.8.2.2.1.1
The statistics for an X.25 interface across all LCIs. The near end of the link refers to the side of the link that the probe is monitoring. The far end is the side the probe is not on. In a X.25 network, there are many far ends of the link, but they shall be logically grouped into one end in this table.
OBJECT-TYPE    
  WanX25HistoryEntry  

wanX25HistoryIndex 1.3.6.1.4.1.11.2.3.7.6.1.5.1.8.2.2.1.1.1
The history of which this entry is a port. The history identified by a particular value of this index is the same history as identified by the same value of historyControlIndex.
OBJECT-TYPE    
  INTEGER 1..65535  

wanX25HistorySampleIndex 1.3.6.1.4.1.11.2.3.7.6.1.5.1.8.2.2.1.1.2
An index that uniquely identifies the particular sample this entry represents among all samples associated with the same historyControlEntry. This index starts at 1 and increases by one as each new sample is taken.
OBJECT-TYPE    
  INTEGER 1..2147483647  

wanX25HistoryIntervalStart 1.3.6.1.4.1.11.2.3.7.6.1.5.1.8.2.2.1.1.3
The value of sysUpTime at the start of the interval over which this sample was measured. If the probe keeps track of time of day, it should start the first sample of the history at a time such that when the next hour of the day begins, a sample is started at that instant. Note that following this rule may require the probe to delay collection the first sample of the history, as each sample must be of the same interval. Also note that the sample which is currently being collected is not accessible in this table until the end of its interval.
OBJECT-TYPE    
  TimeTicks  

wanX25HistoryDropEvents 1.3.6.1.4.1.11.2.3.7.6.1.5.1.8.2.2.1.1.4
The change in value of wanX25StatsDropEvents during the interval.
OBJECT-TYPE    
  Counter64  

wanX25HistoryInFrames 1.3.6.1.4.1.11.2.3.7.6.1.5.1.8.2.2.1.1.5
The change in value of wanX25StatsInFrames during the interval.
OBJECT-TYPE    
  Counter64  

wanX25HistoryOutFrames 1.3.6.1.4.1.11.2.3.7.6.1.5.1.8.2.2.1.1.6
The change in value of wanX25StatsOutFrames during the interval.
OBJECT-TYPE    
  Counter64  

wanX25HistoryInOctets 1.3.6.1.4.1.11.2.3.7.6.1.5.1.8.2.2.1.1.7
The change in value of wanX25StatsInOctets during the interval.
OBJECT-TYPE    
  Counter64  

wanX25HistoryOutOctets 1.3.6.1.4.1.11.2.3.7.6.1.5.1.8.2.2.1.1.8
The change in value of wanX25StatsOutOctets during the interval.
OBJECT-TYPE    
  Counter64  

wanX25HistoryInRejects 1.3.6.1.4.1.11.2.3.7.6.1.5.1.8.2.2.1.1.9
The change in value of wanX25StatsInRejects during the interval.
OBJECT-TYPE    
  Counter64  

wanX25HistoryOutRejects 1.3.6.1.4.1.11.2.3.7.6.1.5.1.8.2.2.1.1.10
The change in value of wanX25StatsOutRejects during the interval.
OBJECT-TYPE    
  Counter64  

wanX25HistoryInAttempts 1.3.6.1.4.1.11.2.3.7.6.1.5.1.8.2.2.1.1.11
The change in value of wanX25StatsInAttempts during the interval.
OBJECT-TYPE    
  Counter64  

wanX25HistoryOutAttempts 1.3.6.1.4.1.11.2.3.7.6.1.5.1.8.2.2.1.1.12
The change in value of wanX25StatsOutAttempts during the interval.
OBJECT-TYPE    
  Counter64  

wanX25HistoryInFailures 1.3.6.1.4.1.11.2.3.7.6.1.5.1.8.2.2.1.1.13
The change in value of wanX25StatsInFailures during the interval.
OBJECT-TYPE    
  Counter64  

wanX25HistoryOutFailures 1.3.6.1.4.1.11.2.3.7.6.1.5.1.8.2.2.1.1.14
The change in value of wanX25StatsOutFailures during the interval.
OBJECT-TYPE    
  Counter64  

wanX25HistoryProviderClears 1.3.6.1.4.1.11.2.3.7.6.1.5.1.8.2.2.1.1.15
The change in value of wanX25StatsProviderClears during the interval.
OBJECT-TYPE    
  Counter64  

wanX25HistoryInResets 1.3.6.1.4.1.11.2.3.7.6.1.5.1.8.2.2.1.1.16
The change in value of wanX25StatsInResets during the interval.
OBJECT-TYPE    
  Counter64  

wanX25HistoryOutResets 1.3.6.1.4.1.11.2.3.7.6.1.5.1.8.2.2.1.1.17
The change in value of wanX25StatsOutResets during the interval.
OBJECT-TYPE    
  Counter64  

wanX25HistoryProviderResets 1.3.6.1.4.1.11.2.3.7.6.1.5.1.8.2.2.1.1.18
The change in value of wanX25StatsProviderResets during the interval.
OBJECT-TYPE    
  Counter64  

wanX25HistoryInAccusedErrors 1.3.6.1.4.1.11.2.3.7.6.1.5.1.8.2.2.1.1.19
The change in value of wanX25StatsInAccusedErrors during the interval.
OBJECT-TYPE    
  Counter64  

wanX25HistoryOutAccusedErrors 1.3.6.1.4.1.11.2.3.7.6.1.5.1.8.2.2.1.1.20
The change in value of wanX25StatsOutAccusedErrors during the interval.
OBJECT-TYPE    
  Counter64  

wanX25HistoryInInterrupts 1.3.6.1.4.1.11.2.3.7.6.1.5.1.8.2.2.1.1.21
The change in value of wanX25StatsInInterrupts during the interval.
OBJECT-TYPE    
  Counter64  

wanX25HistoryOutInterrupts 1.3.6.1.4.1.11.2.3.7.6.1.5.1.8.2.2.1.1.22
The change in value of wanX25StatsOutInterrupts during the interval.
OBJECT-TYPE    
  Counter64  

wanX25HistoryInUtilization 1.3.6.1.4.1.11.2.3.7.6.1.5.1.8.2.2.1.1.23
The best estimated of the mean physical layer network utilization of traffic coming from the far end of the link in hundreds of a percent.
OBJECT-TYPE    
  INTEGER 0..10000  

wanX25HistoryOutUtilization 1.3.6.1.4.1.11.2.3.7.6.1.5.1.8.2.2.1.1.24
The best estimated of the mean physical layer network utilization of traffic coming from the near end of the link in hundreds of a percent.
OBJECT-TYPE    
  INTEGER 0..10000  

wanFrStatsTable 1.3.6.1.4.1.11.2.3.7.6.1.5.1.8.1.2.2
Frame Relay statistics.
OBJECT-TYPE    
  SEQUENCE OF  
    WanFrStatsEntry

wanFrStatsEntry 1.3.6.1.4.1.11.2.3.7.6.1.5.1.8.1.2.2.1
The statistics for a frame relay interface across all DLCIs. The near end of the link refers to the side of the link that the probe is monitoring. The far end is the side the probe is not on. In a frame relay network, there are many far ends of the link, but they shall be logically grouped into one end in this table.
OBJECT-TYPE    
  WanFrStatsEntry  

wanFrStatsIndex 1.3.6.1.4.1.11.2.3.7.6.1.5.1.8.1.2.2.1.1
The value of this object uniquely identifies this wanFrStatsTable entry.
OBJECT-TYPE    
  INTEGER 1..65535  

wanFrStatsDataSource 1.3.6.1.4.1.11.2.3.7.6.1.5.1.8.1.2.2.1.2
This object identifies the source of the data that this wanFrStatsEntry analyzes. This source can be any frame relay interface on this device. In order to identify a particular interface, this object shall identify the instance of the ifIndex object, defined in MIB-II [RFC 1573] for the desired interface. The ifType value associated with the ifIndex can only be frameRelay(32).
OBJECT-TYPE    
  OBJECT IDENTIFIER  

wanFrStatsDropEvents 1.3.6.1.4.1.11.2.3.7.6.1.5.1.8.1.2.2.1.3
The total number of events in which frames were dropped by the probe due to lack of resources. Note that this number is not necessarily the number of frames dropped; it is just the number of times this condition has been detected.
OBJECT-TYPE    
  Counter64  

wanFrStatsInFrames 1.3.6.1.4.1.11.2.3.7.6.1.5.1.8.1.2.2.1.4
The total number of frames seen coming from the far end of the link including error packets.
OBJECT-TYPE    
  Counter64  

wanFrStatsOutFrames 1.3.6.1.4.1.11.2.3.7.6.1.5.1.8.1.2.2.1.5
The total number of frames seen coming from the near end of the link including error packets.
OBJECT-TYPE    
  Counter64  

wanFrStatsInOctets 1.3.6.1.4.1.11.2.3.7.6.1.5.1.8.1.2.2.1.6
The sum of octets from all frames seen originating from the far end of the link including errored frames.
OBJECT-TYPE    
  Counter64  

wanFrStatsOutOctets 1.3.6.1.4.1.11.2.3.7.6.1.5.1.8.1.2.2.1.7
The sum of octets from all frames seen originating from the near end of the link including errored frames.
OBJECT-TYPE    
  Counter64  

wanFrStatsInFECNs 1.3.6.1.4.1.11.2.3.7.6.1.5.1.8.1.2.2.1.8
The number of frames see coming form the far end of the link with the FECN bit set.
OBJECT-TYPE    
  Counter64  

wanFrStatsOutFECNs 1.3.6.1.4.1.11.2.3.7.6.1.5.1.8.1.2.2.1.9
The number of frames see coming form the near end of the link with the FECN bit set.
OBJECT-TYPE    
  Counter64  

wanFrStatsInBECNs 1.3.6.1.4.1.11.2.3.7.6.1.5.1.8.1.2.2.1.10
The number of frames seen coming from the far end of the link with the BECN bit set.
OBJECT-TYPE    
  Counter64  

wanFrStatsOutBECNs 1.3.6.1.4.1.11.2.3.7.6.1.5.1.8.1.2.2.1.11
The number of frames seen coming from the near end of the link with the BECN bit set.
OBJECT-TYPE    
  Counter64  

wanFrStatsInDEs 1.3.6.1.4.1.11.2.3.7.6.1.5.1.8.1.2.2.1.12
The number of frames seen coming from the far end of the link with the DE bit set.
OBJECT-TYPE    
  Counter64  

wanFrStatsOutDEs 1.3.6.1.4.1.11.2.3.7.6.1.5.1.8.1.2.2.1.13
The number of frames seen coming from the near end of the link with the DE bit set.
OBJECT-TYPE    
  Counter64  

wanFrStatsOwner 1.3.6.1.4.1.11.2.3.7.6.1.5.1.8.1.2.2.1.14
The entity that configured this entry.
OBJECT-TYPE    
  OwnerString  

wanFrStatsStatus 1.3.6.1.4.1.11.2.3.7.6.1.5.1.8.1.2.2.1.15
The status of this wanFrStatsTable entry.
OBJECT-TYPE    
  RowStatus  

wanFrHistoryTable 1.3.6.1.4.1.11.2.3.7.6.1.5.1.8.2.2.2
Frame Relay statistics.
OBJECT-TYPE    
  SEQUENCE OF  
    WanFrHistoryEntry

wanFrHistoryEntry 1.3.6.1.4.1.11.2.3.7.6.1.5.1.8.2.2.2.1
The statistics for a frame relay interface across all DLCIs. The near end of the link refers to the side of the link that the probe is monitoring. The far end is the side the probe is not on. In a frame relay network, there are many far ends of the link, but they shall be logically grouped into one end in this table.
OBJECT-TYPE    
  WanFrHistoryEntry  

wanFrHistoryIndex 1.3.6.1.4.1.11.2.3.7.6.1.5.1.8.2.2.2.1.1
The history of which this entry is a port. The history identified by a particular value of this index is the same history as identified by the same value of historyControlIndex.
OBJECT-TYPE    
  INTEGER 1..65535  

wanFrHistorySampleIndex 1.3.6.1.4.1.11.2.3.7.6.1.5.1.8.2.2.2.1.2
An index that uniquely identifies the particular sample this entry represents among all samples associated with the same historyControlEntry. This index starts at 1 and increases by one as each new sample is taken.
OBJECT-TYPE    
  INTEGER 1..2147483647  

wanFrHistoryIntervalStart 1.3.6.1.4.1.11.2.3.7.6.1.5.1.8.2.2.2.1.3
The value of sysUpTime at the start of the interval over which this sample was measured. If the probe keeps track of time of day, it should start the first sample of the history at a time such that when the next hour of the day begins, a sample is started at that instant. Note that following this rule may require the probe to delay collection the first sample of the history, as each sample must be of the same interval. Also note that the sample which is currently being collected is not accessible in this table until the end of its interval.
OBJECT-TYPE    
  TimeTicks  

wanFrHistoryDropEvents 1.3.6.1.4.1.11.2.3.7.6.1.5.1.8.2.2.2.1.4
The change in value of wanFrStatsDropEvents during the interval.
OBJECT-TYPE    
  Counter64  

wanFrHistoryInFrames 1.3.6.1.4.1.11.2.3.7.6.1.5.1.8.2.2.2.1.5
The change in value of wanFrStatsInFrames during the interval.
OBJECT-TYPE    
  Counter64  

wanFrHistoryOutFrames 1.3.6.1.4.1.11.2.3.7.6.1.5.1.8.2.2.2.1.6
The change in value of wanFrStatsOutFrames during the interval.
OBJECT-TYPE    
  Counter64  

wanFrHistoryInOctets 1.3.6.1.4.1.11.2.3.7.6.1.5.1.8.2.2.2.1.7
The change in value of wanFrStatsInOctets during the interval.
OBJECT-TYPE    
  Counter64  

wanFrHistoryOutOctets 1.3.6.1.4.1.11.2.3.7.6.1.5.1.8.2.2.2.1.8
The change in value of wanFrStatsOutOctets during the interval.
OBJECT-TYPE    
  Counter64  

wanFrHistoryInFECNs 1.3.6.1.4.1.11.2.3.7.6.1.5.1.8.2.2.2.1.9
The change in value of wanFrStatsInFECSs during the interval.
OBJECT-TYPE    
  Counter64  

wanFrHistoryOutFECNs 1.3.6.1.4.1.11.2.3.7.6.1.5.1.8.2.2.2.1.10
The change in value of wanFrStatsOutFECNs during the interval.
OBJECT-TYPE    
  Counter64  

wanFrHistoryInBECNs 1.3.6.1.4.1.11.2.3.7.6.1.5.1.8.2.2.2.1.11
The change in value of wanFrStatsInBECNs during the interval.
OBJECT-TYPE    
  Counter64  

wanFrHistoryOutBECNs 1.3.6.1.4.1.11.2.3.7.6.1.5.1.8.2.2.2.1.12
The change in value of wanFrStatsOutBECNs during the interval.
OBJECT-TYPE    
  Counter64  

wanFrHistoryInDEs 1.3.6.1.4.1.11.2.3.7.6.1.5.1.8.2.2.2.1.13
The change in value of wanFrStatsInDEs during the interval.
OBJECT-TYPE    
  Counter64  

wanFrHistoryOutDEs 1.3.6.1.4.1.11.2.3.7.6.1.5.1.8.2.2.2.1.14
The change in value of wanFrStatsDOutDEs during the interval.
OBJECT-TYPE    
  Counter64  

wanFrHistoryInUtilization 1.3.6.1.4.1.11.2.3.7.6.1.5.1.8.2.2.2.1.15
The best estimated of the mean physical layer network utilization of traffic coming from the far end of the link in hundreds of a percent.
OBJECT-TYPE    
  INTEGER 0..10000  

wanFrHistoryOutUtilization 1.3.6.1.4.1.11.2.3.7.6.1.5.1.8.2.2.2.1.16
The best estimated of the mean physical layer network utilization of traffic coming from the near end of the link in hundreds of a percent.
OBJECT-TYPE    
  INTEGER 0..10000  

wanAal5StatsTable 1.3.6.1.4.1.11.2.3.7.6.1.5.1.8.1.2.3
AAL/5 statistics.
OBJECT-TYPE    
  SEQUENCE OF  
    WanAal5StatsEntry

wanAal5StatsEntry 1.3.6.1.4.1.11.2.3.7.6.1.5.1.8.1.2.3.1
The statistics for a AAL/5 interface. The near end of the link refers to the side of the link that the probe is monitoring. The far end is the side the probe is not on. In an ATM network, there are many far ends of the link, but they shall be logically grouped into one end in this table.
OBJECT-TYPE    
  WanAal5StatsEntry  

wanAal5StatsIndex 1.3.6.1.4.1.11.2.3.7.6.1.5.1.8.1.2.3.1.1
The value of this object uniquely identifies this wanAal5StatsTable entry.
OBJECT-TYPE    
  INTEGER 1..65535  

wanAal5StatsDataSource 1.3.6.1.4.1.11.2.3.7.6.1.5.1.8.1.2.3.1.2
This object identifies the source of the data that this wanAal5StatsEntry analyzes. This source can be any interface on this device. In order to identify a particular interface, this object shall identify the instance of the ifIndex object, defined in MIB-II [RFC 1573] for the desired interface. The ifType value associated with the ifIndex can only be aal5(49).
OBJECT-TYPE    
  OBJECT IDENTIFIER  

wanAal5StatsDropEvents 1.3.6.1.4.1.11.2.3.7.6.1.5.1.8.1.2.3.1.3
The total number of events in which frames were dropped by the probe due to lack of resources. Note that this number is not necessarily the number of frames dropped; it is just the number of times this condition has been detected.
OBJECT-TYPE    
  Counter64  

wanAal5StatsInCells 1.3.6.1.4.1.11.2.3.7.6.1.5.1.8.1.2.3.1.4
The total number of cells for any AAL-5 connection seen coming from the far end of the link.
OBJECT-TYPE    
  Counter64  

wanAal5StatsOutCells 1.3.6.1.4.1.11.2.3.7.6.1.5.1.8.1.2.3.1.5
The total number of cells for any AAL-5 connection seen coming from the near end of the link.
OBJECT-TYPE    
  Counter64  

wanAal5StatsInPDUs 1.3.6.1.4.1.11.2.3.7.6.1.5.1.8.1.2.3.1.6
The total number of AAL-5 PDUs seen coming from the far end of the link including error PDUs.
OBJECT-TYPE    
  Counter64  

wanAal5StatsOutPDUs 1.3.6.1.4.1.11.2.3.7.6.1.5.1.8.1.2.3.1.7
The total number of AAL-5 PDUs seen coming from the near end of the link including error PDUs.
OBJECT-TYPE    
  Counter64  

wanAal5StatsInOctets 1.3.6.1.4.1.11.2.3.7.6.1.5.1.8.1.2.3.1.8
The sum of octets from all AAL-5 PDUs seen originating from the far end of the link including errored PDUs.
OBJECT-TYPE    
  Counter64  

wanAal5StatsOutOctets 1.3.6.1.4.1.11.2.3.7.6.1.5.1.8.1.2.3.1.9
The sum of octets from all AAL-5 PDUs seen originating from the near end of the link including errored PDUs.
OBJECT-TYPE    
  Counter64  

wanAal5StatsInCLP1 1.3.6.1.4.1.11.2.3.7.6.1.5.1.8.1.2.3.1.10
The total number of cells for any AAL-5 connection with the CLP bit set seen coming from the far end of the link.
OBJECT-TYPE    
  Counter64  

wanAal5StatsOutCLP1 1.3.6.1.4.1.11.2.3.7.6.1.5.1.8.1.2.3.1.11
The total number of cells for any AAL-5 connection with the CLP bit set seen coming from the near end of the link.
OBJECT-TYPE    
  Counter64  

wanAal5StatsInCRCs 1.3.6.1.4.1.11.2.3.7.6.1.5.1.8.1.2.3.1.12
The total number of AAL-5 PDUs with CRC errors from the far end of the link.
OBJECT-TYPE    
  Counter64  

wanAal5StatsOutCRCs 1.3.6.1.4.1.11.2.3.7.6.1.5.1.8.1.2.3.1.13
The total number of AAL-5 PDUs with CRC errors from the near end of the link.
OBJECT-TYPE    
  Counter64  

wanAal5StatsInOversizedSDUs 1.3.6.1.4.1.11.2.3.7.6.1.5.1.8.1.2.3.1.14
The total number of AAL-5 SDUs from the far end of the link that were too large.
OBJECT-TYPE    
  Counter64  

wanAal5StatsOutOversizedSDUs 1.3.6.1.4.1.11.2.3.7.6.1.5.1.8.1.2.3.1.15
The total number of AAL-5 SDUs from the near end of the link that were too large.
OBJECT-TYPE    
  Counter64  

wanAal5StatsInSVCs 1.3.6.1.4.1.11.2.3.7.6.1.5.1.8.1.2.3.1.16
The total number of AAL/5 connections seen initiated from the far end of the link.
OBJECT-TYPE    
  Counter64  

wanAal5StatsOutSVCs 1.3.6.1.4.1.11.2.3.7.6.1.5.1.8.1.2.3.1.17
The total number of AAL-5 connections seen initiated from the near end of the link.
OBJECT-TYPE    
  Counter64  

wanAal5StatsOwner 1.3.6.1.4.1.11.2.3.7.6.1.5.1.8.1.2.3.1.18
The entity that configured this entry.
OBJECT-TYPE    
  OwnerString  

wanAal5StatsStatus 1.3.6.1.4.1.11.2.3.7.6.1.5.1.8.1.2.3.1.19
The status of this wanAal5StatsTable entry.
OBJECT-TYPE    
  RowStatus  

wanAal5HistoryTable 1.3.6.1.4.1.11.2.3.7.6.1.5.1.8.2.2.3
AAL/5 statistics.
OBJECT-TYPE    
  SEQUENCE OF  
    WanAal5HistoryEntry

wanAal5HistoryEntry 1.3.6.1.4.1.11.2.3.7.6.1.5.1.8.2.2.3.1
The statistics for a AAL/5 interface. The near end of the link refers to the side of the link that the probe is monitoring. The far end is the side the probe is not on. In an ATM network, there are many far ends of the link, but they shall be logically grouped into one end in this table.
OBJECT-TYPE    
  WanAal5HistoryEntry  

wanAal5HistoryIndex 1.3.6.1.4.1.11.2.3.7.6.1.5.1.8.2.2.3.1.1
The history of which this entry is a port. The history identified by a particular value of this index is the same history as identified by the same value of historyControlIndex.
OBJECT-TYPE    
  INTEGER 1..65535  

wanAal5HistorySampleIndex 1.3.6.1.4.1.11.2.3.7.6.1.5.1.8.2.2.3.1.2
An index that uniquely identifies the particular sample this entry represents among all samples associated with the same historyControlEntry. This index starts at 1 and increases by one as each new sample is taken.
OBJECT-TYPE    
  INTEGER 1..2147483647  

wanAal5HistoryIntervalStart 1.3.6.1.4.1.11.2.3.7.6.1.5.1.8.2.2.3.1.3
The value of sysUpTime at the start of the interval over which this sample was measured. If the probe keeps track of time of day, it should start the first sample of the history at a time such that when the next hour of the day begins, a sample is started at that instant. Note that following this rule may require the probe to delay collection the first sample of the history, as each sample must be of the same interval. Also note that the sample which is currently being collected is not accessible in this table until the end of its interval.
OBJECT-TYPE    
  TimeTicks  

wanAal5HistoryDropEvents 1.3.6.1.4.1.11.2.3.7.6.1.5.1.8.2.2.3.1.4
The change in value of wanAal5StatsDropEvents during the interval.
OBJECT-TYPE    
  Counter64  

wanAal5HistoryInCells 1.3.6.1.4.1.11.2.3.7.6.1.5.1.8.2.2.3.1.5
The change in value of wanAal5StatsInCells during the interval.
OBJECT-TYPE    
  Counter64  

wanAal5HistoryOutCells 1.3.6.1.4.1.11.2.3.7.6.1.5.1.8.2.2.3.1.6
The change in value of wanAal5StatsOutCells during the interval.
OBJECT-TYPE    
  Counter64  

wanAal5HistoryInPDUs 1.3.6.1.4.1.11.2.3.7.6.1.5.1.8.2.2.3.1.7
The change in value of wanAal5StatsInPDUs during the interval.
OBJECT-TYPE    
  Counter64  

wanAal5HistoryOutPDUs 1.3.6.1.4.1.11.2.3.7.6.1.5.1.8.2.2.3.1.8
The change in value of wanAal5StatsOutPDUs during the interval.
OBJECT-TYPE    
  Counter64  

wanAal5HistoryInOctets 1.3.6.1.4.1.11.2.3.7.6.1.5.1.8.2.2.3.1.9
The change in value of wanAal5StatsInOctets during the interval.
OBJECT-TYPE    
  Counter64  

wanAal5HistoryOutOctets 1.3.6.1.4.1.11.2.3.7.6.1.5.1.8.2.2.3.1.10
The change in value of wanAal5StatsOutOctets during the interval.
OBJECT-TYPE    
  Counter64  

wanAal5HistoryInCLP1 1.3.6.1.4.1.11.2.3.7.6.1.5.1.8.2.2.3.1.11
The change in value of wanAal5StatsInCLP1 the interval.
OBJECT-TYPE    
  Counter64  

wanAal5HistoryOutCLP1 1.3.6.1.4.1.11.2.3.7.6.1.5.1.8.2.2.3.1.12
The change in value of wanAal5StatsOutCLP1 during the interval.
OBJECT-TYPE    
  Counter64  

wanAal5HistoryInCRCs 1.3.6.1.4.1.11.2.3.7.6.1.5.1.8.2.2.3.1.13
The change in value of wanAal5StatsInCRCs during the interval.
OBJECT-TYPE    
  Counter64  

wanAal5HistoryOutCRCs 1.3.6.1.4.1.11.2.3.7.6.1.5.1.8.2.2.3.1.14
The change in value of wanAal5StatsOutCRCs during the interval.
OBJECT-TYPE    
  Counter64  

wanAal5HistoryInOversizedSDUs 1.3.6.1.4.1.11.2.3.7.6.1.5.1.8.2.2.3.1.15
The change in value of wanAal5StatsInOversizedSDUs during the interval.
OBJECT-TYPE    
  Counter64  

wanAal5HistoryOutOversizedSDUs 1.3.6.1.4.1.11.2.3.7.6.1.5.1.8.2.2.3.1.16
The change in value of wanAal5StatsOutOversizedSDUs during the interval.
OBJECT-TYPE    
  Counter64  

wanAal5HistoryInSVCs 1.3.6.1.4.1.11.2.3.7.6.1.5.1.8.2.2.3.1.17
The change in value of wanAal5StatsInSVCs during the interval.
OBJECT-TYPE    
  Counter64  

wanAal5HistoryOutSVCs 1.3.6.1.4.1.11.2.3.7.6.1.5.1.8.2.2.3.1.18
The change in value of wanAal5StatsOutSVCs during the interval.
OBJECT-TYPE    
  Counter64  

wanAal5HistoryInUtilization 1.3.6.1.4.1.11.2.3.7.6.1.5.1.8.2.2.3.1.19
The best estimated of the mean AAL-5 layer network utilization of traffic coming from the far end of the link in hundreds of a percent.
OBJECT-TYPE    
  INTEGER 0..10000  

wanAal5HistoryOutUtilization 1.3.6.1.4.1.11.2.3.7.6.1.5.1.8.2.2.3.1.20
The best estimated of the mean AAL-5 layer network utilization of traffic coming from the near end of the link in hundreds of a percent.
OBJECT-TYPE    
  INTEGER 0..10000  

wanPppStatsTable 1.3.6.1.4.1.11.2.3.7.6.1.5.1.8.1.2.4
PPP in HDLC service statistics.
OBJECT-TYPE    
  SEQUENCE OF  
    WanPppStatsEntry

wanPppStatsEntry 1.3.6.1.4.1.11.2.3.7.6.1.5.1.8.1.2.4.1
The statistics for a PPP in HDLC service. The near end of the link refers to the side of the link that the probe is monitoring. The far end is the side the probe is not on.
OBJECT-TYPE    
  WanPppStatsEntry  

wanPppStatsIndex 1.3.6.1.4.1.11.2.3.7.6.1.5.1.8.1.2.4.1.1
The value of this object uniquely identifies this wanPppStatsTable entry.
OBJECT-TYPE    
  INTEGER 1..65535  

wanPppStatsDataSource 1.3.6.1.4.1.11.2.3.7.6.1.5.1.8.1.2.4.1.2
This object identifies the source of the data that this wanPppStatsEntry analyzes. This source can be any interface on this device. In order to identify a particular interface, this object shall identify the instance of the ifIndex object, defined in MIB-II [RFC 1573] for the desired interface. The ifType value associated with the ifIndex can only be ppp(22).
OBJECT-TYPE    
  OBJECT IDENTIFIER  

wanPppStatsDropEvents 1.3.6.1.4.1.11.2.3.7.6.1.5.1.8.1.2.4.1.3
The total number of events in which frames were dropped by the probe due to lack of resources. Note that this number is not necessarily the number of frames dropped; it is just the number of times this condition has been detected.
OBJECT-TYPE    
  Counter64  

wanPppStatsInFrames 1.3.6.1.4.1.11.2.3.7.6.1.5.1.8.1.2.4.1.4
The total number of frames seen coming from the far end of the link including error frames.
OBJECT-TYPE    
  Counter64  

wanPppStatsOutFrames 1.3.6.1.4.1.11.2.3.7.6.1.5.1.8.1.2.4.1.5
The total number of frames seen coming from the near end of the link including error frames.
OBJECT-TYPE    
  Counter64  

wanPppStatsInOctets 1.3.6.1.4.1.11.2.3.7.6.1.5.1.8.1.2.4.1.6
The sum of octets from all frames seen coming from the far end of the link including errored frames.
OBJECT-TYPE    
  Counter64  

wanPppStatsOutOctets 1.3.6.1.4.1.11.2.3.7.6.1.5.1.8.1.2.4.1.7
The sum of octets from all frames seen coming from the near end of the link including errored frames.
OBJECT-TYPE    
  Counter64  

wanPppStatsInBadAddresses 1.3.6.1.4.1.11.2.3.7.6.1.5.1.8.1.2.4.1.8
The number of frames seen from the far end of the link with an incorrect address field.
OBJECT-TYPE    
  Counter64  

wanPppStatsOutBadAddresses 1.3.6.1.4.1.11.2.3.7.6.1.5.1.8.1.2.4.1.9
The number of frames seen from the near end of the link with an incorrect address field
OBJECT-TYPE    
  Counter64  

wanPppStatsInBadControls 1.3.6.1.4.1.11.2.3.7.6.1.5.1.8.1.2.4.1.10
The number of frames seen from the far end of the link with an incorrect control field.
OBJECT-TYPE    
  Counter64  

wanPppStatsOutBadControls 1.3.6.1.4.1.11.2.3.7.6.1.5.1.8.1.2.4.1.11
The number of frames seen from the near end of the link with an incorrect control field.
OBJECT-TYPE    
  Counter64  

wanPppStatsInLongFrames 1.3.6.1.4.1.11.2.3.7.6.1.5.1.8.1.2.4.1.12
The number of frames seen from the far end of the link that exceed the MRU.
OBJECT-TYPE    
  Counter64  

wanPppStatsOutLongFrames 1.3.6.1.4.1.11.2.3.7.6.1.5.1.8.1.2.4.1.13
The number of frames seen from the near end of the link that exceed the MRU.
OBJECT-TYPE    
  Counter64  

wanPppStatsInBadFCSs 1.3.6.1.4.1.11.2.3.7.6.1.5.1.8.1.2.4.1.14
The number of packets seen from the far end of the link with incorrect FCSs.
OBJECT-TYPE    
  Counter64  

wanPppStatsOutBadFCSs 1.3.6.1.4.1.11.2.3.7.6.1.5.1.8.1.2.4.1.15
The number of packets seen from the near end of the link with incorrect FCSs.
OBJECT-TYPE    
  Counter64  

wanPppStatsOwner 1.3.6.1.4.1.11.2.3.7.6.1.5.1.8.1.2.4.1.16
The entity that configured this entry.
OBJECT-TYPE    
  OwnerString  

wanPppStatsStatus 1.3.6.1.4.1.11.2.3.7.6.1.5.1.8.1.2.4.1.17
The status of this wanPppStatsTable entry.
OBJECT-TYPE    
  RowStatus  

wanPppHistoryTable 1.3.6.1.4.1.11.2.3.7.6.1.5.1.8.2.2.4
PPP in HDLC service statistics.
OBJECT-TYPE    
  SEQUENCE OF  
    WanPppHistoryEntry

wanPppHistoryEntry 1.3.6.1.4.1.11.2.3.7.6.1.5.1.8.2.2.4.1
The statistics for a PPP in HDLC service. The near end of the link refers to the side of the link that the probe is monitoring. The far end is the side the probe is not on.
OBJECT-TYPE    
  WanPppHistoryEntry  

wanPppHistoryIndex 1.3.6.1.4.1.11.2.3.7.6.1.5.1.8.2.2.4.1.1
The history of which this entry is a port. The history identified by a particular value of this index is the same history as identified by the same value of historyControlIndex.
OBJECT-TYPE    
  INTEGER 1..65535  

wanPppHistorySampleIndex 1.3.6.1.4.1.11.2.3.7.6.1.5.1.8.2.2.4.1.2
An index that uniquely identifies the particular sample this entry represents among all samples associated with the same historyControlEntry. This index starts at 1 and increases by one as each new sample is taken.
OBJECT-TYPE    
  INTEGER 1..2147483647  

wanPppHistoryIntervalStart 1.3.6.1.4.1.11.2.3.7.6.1.5.1.8.2.2.4.1.3
The value of sysUpTime at the start of the interval over which this sample was measured. If the probe keeps track of time of day, it should start the first sample of the history at a time such that when the next hour of the day begins, a sample is started at that instant. Note that following this rule may require the probe to delay collection the first sample of the history, as each sample must be of the same interval. Also note that the sample which is currently being collected is not accessible in this table until the end of its interval.
OBJECT-TYPE    
  TimeTicks  

wanPppHistoryDropEvents 1.3.6.1.4.1.11.2.3.7.6.1.5.1.8.2.2.4.1.4
The change in value of wanPppStatsDropEvents during the interval.
OBJECT-TYPE    
  Counter64  

wanPppHistoryInFrames 1.3.6.1.4.1.11.2.3.7.6.1.5.1.8.2.2.4.1.5
The change in value of wanPppStatsInFrames during the interval.
OBJECT-TYPE    
  Counter64  

wanPppHistoryOutFrames 1.3.6.1.4.1.11.2.3.7.6.1.5.1.8.2.2.4.1.6
The change in value of wanPppStatsOutFrames during the interval.
OBJECT-TYPE    
  Counter64  

wanPppHistoryInOctets 1.3.6.1.4.1.11.2.3.7.6.1.5.1.8.2.2.4.1.7
The change in value of wanPppStatsInOctets during the interval.
OBJECT-TYPE    
  Counter64  

wanPppHistoryOutOctets 1.3.6.1.4.1.11.2.3.7.6.1.5.1.8.2.2.4.1.8
The change in value of wanPppStatsOutOctets during the interval.
OBJECT-TYPE    
  Counter64  

wanPppHistoryInBadAddresses 1.3.6.1.4.1.11.2.3.7.6.1.5.1.8.2.2.4.1.9
The change in value of wanPppStatsInBadAddresses during the interval.
OBJECT-TYPE    
  Counter64  

wanPppHistoryOutBadAddresses 1.3.6.1.4.1.11.2.3.7.6.1.5.1.8.2.2.4.1.10
The change in value of wanPppStatsOutBadAddresses during the interval.
OBJECT-TYPE    
  Counter64  

wanPppHistoryInBadControls 1.3.6.1.4.1.11.2.3.7.6.1.5.1.8.2.2.4.1.11
The change in value of wanPppStatsInBadControls during the interval.
OBJECT-TYPE    
  Counter64  

wanPppHistoryOutBadControls 1.3.6.1.4.1.11.2.3.7.6.1.5.1.8.2.2.4.1.12
The change in value of wanPppStatsOutBadControls during the interval.
OBJECT-TYPE    
  Counter64  

wanPppHistoryInLongFrames 1.3.6.1.4.1.11.2.3.7.6.1.5.1.8.2.2.4.1.13
The change in value of wanPppStatsInLongFrames during the interval.
OBJECT-TYPE    
  Counter64  

wanPppHistoryOutLongFrames 1.3.6.1.4.1.11.2.3.7.6.1.5.1.8.2.2.4.1.14
The change in value of wanPppStatsOutLongFrames during the interval.
OBJECT-TYPE    
  Counter64  

wanPppHistoryInBadFCSs 1.3.6.1.4.1.11.2.3.7.6.1.5.1.8.2.2.4.1.15
The change in value of wanPppStatsInBadFCSs during the interval.
OBJECT-TYPE    
  Counter64  

wanPppHistoryOutBadFCSs 1.3.6.1.4.1.11.2.3.7.6.1.5.1.8.2.2.4.1.16
The change in value of wanPppStatsOutBadFCSs during the interval.
OBJECT-TYPE    
  Counter64  

wanPppHistoryInUtilization 1.3.6.1.4.1.11.2.3.7.6.1.5.1.8.2.2.4.1.17
The best estimated of the mean physical layer network utilization of traffic coming from the far end of the link in hundreds of a percent.
OBJECT-TYPE    
  INTEGER 0..10000  

wanPppHistoryOutUtilization 1.3.6.1.4.1.11.2.3.7.6.1.5.1.8.2.2.4.1.18
The best estimated of the mean physical layer network utilization of traffic coming from the near end of the link in hundreds of a percent.
OBJECT-TYPE    
  INTEGER 0..10000  

wanX25PvcStatsTable 1.3.6.1.4.1.11.2.3.7.6.1.5.1.8.1.3.1
X.25 per-LCI statistics for a PVC.
OBJECT-TYPE    
  SEQUENCE OF  
    WanX25PvcStatsEntry

wanX25PvcStatsEntry 1.3.6.1.4.1.11.2.3.7.6.1.5.1.8.1.3.1.1
The statistics for a X.25 PVC. The near end of the link refers to the side of the link that the probe is monitoring. The far end is the sides the probe is not on.
OBJECT-TYPE    
  WanX25PvcStatsEntry  

wanX25PvcStatsIndex 1.3.6.1.4.1.11.2.3.7.6.1.5.1.8.1.3.1.1.1
The value of this object uniquely identifies this wanX25PvcStatsTable entry.
OBJECT-TYPE    
  INTEGER 1..65535  

wanX25PvcStatsDataSource 1.3.6.1.4.1.11.2.3.7.6.1.5.1.8.1.3.1.1.2
This object identifies the source of the data that this wanX25PvcStatsEntry analyzes. This source can be any pvcEntry associated with an X.25 interface. In order to identify a particular LCI to monitor, this object shall identify the instance of the pvcIndex object that corresponds to a X.25 PVC, defined above for the desired interface.
OBJECT-TYPE    
  OBJECT IDENTIFIER  

wanX25PvcStatsDropEvents 1.3.6.1.4.1.11.2.3.7.6.1.5.1.8.1.3.1.1.3
The total number of events in which frames were dropped by the probe due to lack of resources. Note that this number is not necessarily the number of frames dropped; it is just the number of times this condition has been detected.
OBJECT-TYPE    
  Counter64  

wanX25PvcStatsInFrames 1.3.6.1.4.1.11.2.3.7.6.1.5.1.8.1.3.1.1.4
The total number of frames seen coming from the far end of the link on this LCI.
OBJECT-TYPE    
  Counter64  

wanX25PvcStatsOutFrames 1.3.6.1.4.1.11.2.3.7.6.1.5.1.8.1.3.1.1.5
The total number of frames seen coming from the near end of the link on this LCI.
OBJECT-TYPE    
  Counter64  

wanX25PvcStatsInOctets 1.3.6.1.4.1.11.2.3.7.6.1.5.1.8.1.3.1.1.6
The sum of octets from all frames seen originating from the far end of the link on this LCI.
OBJECT-TYPE    
  Counter64  

wanX25PvcStatsOutOctets 1.3.6.1.4.1.11.2.3.7.6.1.5.1.8.1.3.1.1.7
The sum of octets from all frames seen originating from the near end of the link on this LCI.
OBJECT-TYPE    
  Counter64  

wanX25PvcStatsInResets 1.3.6.1.4.1.11.2.3.7.6.1.5.1.8.1.3.1.1.8
The number of reset requests seen from the far end of the link with cause code DTE initiated for this LCI.
OBJECT-TYPE    
  Counter64  

wanX25PvcStatsOutResets 1.3.6.1.4.1.11.2.3.7.6.1.5.1.8.1.3.1.1.9
The number of reset requests seen from the far end of the link with cause code DTE initiated for this LCI.
OBJECT-TYPE    
  Counter64  

wanX25PvcStatsProviderResets 1.3.6.1.4.1.11.2.3.7.6.1.5.1.8.1.3.1.1.10
The number of reset requests seen with cause code other than DTE initiated for this LCI.
OBJECT-TYPE    
  Counter64  

wanX25PvcStatsInAccusedErrors 1.3.6.1.4.1.11.2.3.7.6.1.5.1.8.1.3.1.1.11
The numbers of frames seen from the far end of the link containing a procedure error cause code on this LCI. These include clear, reset, restart, or diagnostic packets.
OBJECT-TYPE    
  Counter64  

wanX25PvcStatsOutAccusedErrors 1.3.6.1.4.1.11.2.3.7.6.1.5.1.8.1.3.1.1.12
The numbers of frames seen from the near end of the link containing a procedure error cause code on this LCI. These include clear, reset, restart, or diagnostic packets.
OBJECT-TYPE    
  Counter64  

wanX25PvcStatsInInterrupts 1.3.6.1.4.1.11.2.3.7.6.1.5.1.8.1.3.1.1.13
The number of interrupts frames seen coming from the far end of the link on this LCI.
OBJECT-TYPE    
  Counter64  

wanX25PvcStatsOutInterrupts 1.3.6.1.4.1.11.2.3.7.6.1.5.1.8.1.3.1.1.14
The number of interrupts frames seen coming from the far end of the link on this LCI.
OBJECT-TYPE    
  Counter64  

wanX25PvcStatsUpTime 1.3.6.1.4.1.11.2.3.7.6.1.5.1.8.1.3.1.1.15
The total amount of time in one-hundreds of a second that the probe is sure this LCI was active, i.e., the total time the value of wanX25PvcStatsState was equal to up(1). A value of less than the age of this entry does not necessarily mean that this LCI was down. It only means the probe was not certain it was up. Note: the sum of wanX25PvcStatsUpTime and wanX25PvcStatsDownTime may be less than the age of this entry. In this case, the unaccounted for time is the time the probe was uncertain of the state of this LCI, i.e., the total time the value of wanX25PvcStatsState was unknown(3).
OBJECT-TYPE    
  TimeTicks  

wanX25PvcStatsDownTime 1.3.6.1.4.1.11.2.3.7.6.1.5.1.8.1.3.1.1.16
The total amount of time in one-hundreds of a second that the probe is sure this LCI was down, i.e., the total time the value of wanX25PvcStatsState was equal to down(3). A value of less than the age of this entry does not necessarily mean that this LCI was up at some point. It only means the probe was not certain it was down. Note: the sum of wanX25PvcStatsUpTime and wanX25PvcStatsDownTime may be less than the age of this entry. In this case, the unaccounted for time is the time the probe was uncertain of the state of this LCI, i.e., the total time the value of wanX25PvcStatsState was unknown(3).
OBJECT-TYPE    
  TimeTicks  

wanX25PvcStatsState 1.3.6.1.4.1.11.2.3.7.6.1.5.1.8.1.3.1.1.17
The current state of this LCI as inferred by the probe. A value of up(2) means the LCI is active. A value of down(2) means the LCI is inactive. And a value of unknown(3) means the probe cannot currently infer the state.
OBJECT-TYPE    
  INTEGER up(1), down(2), unknown(3)  

wanX25PvcStatsStateChanges 1.3.6.1.4.1.11.2.3.7.6.1.5.1.8.1.3.1.1.18
The count of the number of times the wanX25PvcStatsState has gone from up(1) to down(2) or vice versa. The number of times wanX25PvcStatsState goes to unknown(3) is not counted. However, if the value goes from up(1) to unknown(3) and then to down(2) should be counted as 1. Likewise going from down(2) to unknown(3) and then to up(3) should be counted as 1.
OBJECT-TYPE    
  Counter64  

wanX25PvcStatsOwner 1.3.6.1.4.1.11.2.3.7.6.1.5.1.8.1.3.1.1.19
The entity that configured this entry.
OBJECT-TYPE    
  OwnerString  

wanX25PvcStatsStatus 1.3.6.1.4.1.11.2.3.7.6.1.5.1.8.1.3.1.1.20
The status of this wanX25PvcStatsTable entry.
OBJECT-TYPE    
  RowStatus  

wanX25PvcHistoryTable 1.3.6.1.4.1.11.2.3.7.6.1.5.1.8.2.3.1
X.25 per LCI statistics.
OBJECT-TYPE    
  SEQUENCE OF  
    WanX25PvcHistoryEntry

wanX25PvcHistoryEntry 1.3.6.1.4.1.11.2.3.7.6.1.5.1.8.2.3.1.1
The statistics for a X.25 LCI. The near end of the link refers to the side of the link that the probe is monitoring. The far end is the side the probe is not on.
OBJECT-TYPE    
  WanX25PvcHistoryEntry  

wanX25PvcHistoryIndex 1.3.6.1.4.1.11.2.3.7.6.1.5.1.8.2.3.1.1.1
The history of which this entry is a port. The history identified by a particular value of this index is the same history as identified by the same value of historyControlIndex.
OBJECT-TYPE    
  INTEGER 1..65535  

wanX25PvcHistorySampleIndex 1.3.6.1.4.1.11.2.3.7.6.1.5.1.8.2.3.1.1.2
An index that uniquely identifies the particular sample this entry represents among all samples associated with the same historyControlEntry. This index starts at 1 and increases by one as each new sample is taken.
OBJECT-TYPE    
  INTEGER 1..2147483647  

wanX25PvcHistoryIntervalStart 1.3.6.1.4.1.11.2.3.7.6.1.5.1.8.2.3.1.1.3
The value of sysUpTime at the start of the interval over which this sample was measured. If the probe keeps track of time of day, it should start the first sample of the history at a time such that when the next hour of the day begins, a sample is started at that instant. Note that following this rule may require the probe to delay collection the first sample of the history, as each sample must be of the same interval. Also note that the sample which is currently being collected is not accessible in this table until the end of its interval.
OBJECT-TYPE    
  TimeTicks  

wanX25PvcHistoryDropEvents 1.3.6.1.4.1.11.2.3.7.6.1.5.1.8.2.3.1.1.4
The change in value of wanX25PvcStatsDropEvents during the interval.
OBJECT-TYPE    
  Counter64  

wanX25PvcHistoryInFrames 1.3.6.1.4.1.11.2.3.7.6.1.5.1.8.2.3.1.1.5
The change in value of wanX25PvcStatsInFrames during the interval.
OBJECT-TYPE    
  Counter64  

wanX25PvcHistoryOutFrames 1.3.6.1.4.1.11.2.3.7.6.1.5.1.8.2.3.1.1.6
The change in value of wanX25PvcStatsOutFrames during the interval.
OBJECT-TYPE    
  Counter64  

wanX25PvcHistoryInOctets 1.3.6.1.4.1.11.2.3.7.6.1.5.1.8.2.3.1.1.7
The change in value of wanX25PvcStatsInOctets during the interval.
OBJECT-TYPE    
  Counter64  

wanX25PvcHistoryOutOctets 1.3.6.1.4.1.11.2.3.7.6.1.5.1.8.2.3.1.1.8
The change in value of wanX25PvcStatsOutOctets during the interval.
OBJECT-TYPE    
  Counter64  

wanX25PvcHistoryInResets 1.3.6.1.4.1.11.2.3.7.6.1.5.1.8.2.3.1.1.9
The change in value of wanX25PvcStatsInResets during the interval.
OBJECT-TYPE    
  Counter64  

wanX25PvcHistoryOutResets 1.3.6.1.4.1.11.2.3.7.6.1.5.1.8.2.3.1.1.10
The change in value of wanX25PvcStatsOutResets during the interval.
OBJECT-TYPE    
  Counter64  

wanX25PvcHistoryProviderResets 1.3.6.1.4.1.11.2.3.7.6.1.5.1.8.2.3.1.1.11
The change in value of wanX25PvcStatsProviderResets during the interval.
OBJECT-TYPE    
  Counter64  

wanX25PvcHistoryInAccusedErrors 1.3.6.1.4.1.11.2.3.7.6.1.5.1.8.2.3.1.1.12
The change in value of wanX25PvcStatsInAccusedErrors during the interval.
OBJECT-TYPE    
  Counter64  

wanX25PvcHistoryOutAccusedErrors 1.3.6.1.4.1.11.2.3.7.6.1.5.1.8.2.3.1.1.13
The change in value of wanX25PvcStatsOutAccusedErrors during the interval.
OBJECT-TYPE    
  Counter64  

wanX25PvcHistoryInInterrupts 1.3.6.1.4.1.11.2.3.7.6.1.5.1.8.2.3.1.1.14
The change in value of wanX25PvcStatsInInterrupts during the interval.
OBJECT-TYPE    
  Counter64  

wanX25PvcHistoryOutInterrupts 1.3.6.1.4.1.11.2.3.7.6.1.5.1.8.2.3.1.1.15
The change in value of wanX25PvcStatsOutInterrupts during the interval.
OBJECT-TYPE    
  Counter64  

wanX25PvcHistoryUpTime 1.3.6.1.4.1.11.2.3.7.6.1.5.1.8.2.3.1.1.16
The change in value of wanX25PvcStatsUpTime during the interval.
OBJECT-TYPE    
  TimeTicks  

wanX25PvcHistoryDownTime 1.3.6.1.4.1.11.2.3.7.6.1.5.1.8.2.3.1.1.17
The change in value of wanX25PvcStatsDownTime during the interval.
OBJECT-TYPE    
  TimeTicks  

wanX25PvcHistoryStateChanges 1.3.6.1.4.1.11.2.3.7.6.1.5.1.8.2.3.1.1.18
The change in value of wanX25PvcStatsStateChanges during the interval.
OBJECT-TYPE    
  Counter64  

wanX25PvcHistoryInUtilization 1.3.6.1.4.1.11.2.3.7.6.1.5.1.8.2.3.1.1.19
The best estimated of the mean utilization of traffic on this LCI coming from the far end of the link in hundreds of percent of the CIR.
OBJECT-TYPE    
  INTEGER 0..10000  

wanX25PvcHistoryOutUtilization 1.3.6.1.4.1.11.2.3.7.6.1.5.1.8.2.3.1.1.20
The best estimated of the mean utilization of traffic on this LCI coming from the near end of the link in hundreds of percent of CIR.
OBJECT-TYPE    
  INTEGER 0..10000  

wanFrPvcStatsTable 1.3.6.1.4.1.11.2.3.7.6.1.5.1.8.1.3.2
Frame Relay per-DLCI statistics.
OBJECT-TYPE    
  SEQUENCE OF  
    WanFrPvcStatsEntry

wanFrPvcStatsEntry 1.3.6.1.4.1.11.2.3.7.6.1.5.1.8.1.3.2.1
The statistics for a frame relay DLCI. The near end of the link refers to the side of the link that the probe is monitoring. The far end is the side the probe is not on.
OBJECT-TYPE    
  WanFrPvcStatsEntry  

wanFrPvcStatsIndex 1.3.6.1.4.1.11.2.3.7.6.1.5.1.8.1.3.2.1.1
The value of this object uniquely identifies this wanFrPvcStatsTable entry.
OBJECT-TYPE    
  INTEGER 1..65535  

wanFrPvcStatsDataSource 1.3.6.1.4.1.11.2.3.7.6.1.5.1.8.1.3.2.1.2
This object identifies the source of the data that this wanFrPvcStatsEntry analyzes. This source can be any pvcEntry associated with a frame relay interface on this device. In order to identify a particular DLCI, this object shall identify the instance of the frame relay pvcIndex object, defined in the PVCCONFIG-MIB.
OBJECT-TYPE    
  OBJECT IDENTIFIER  

wanFrPvcStatsDropEvents 1.3.6.1.4.1.11.2.3.7.6.1.5.1.8.1.3.2.1.3
The total number of events in which frames were dropped by the probe due to lack of resources. Note that this number is not necessarily the number of frames dropped; it is just the number of times this condition has been detected.
OBJECT-TYPE    
  Counter64  

wanFrPvcStatsInFrames 1.3.6.1.4.1.11.2.3.7.6.1.5.1.8.1.3.2.1.4
The total number of frames seen coming from the far end of the link on this DLCI.
OBJECT-TYPE    
  Counter64  

wanFrPvcStatsOutFrames 1.3.6.1.4.1.11.2.3.7.6.1.5.1.8.1.3.2.1.5
The total number of frames seen coming from the near end of the link on this DLCI.
OBJECT-TYPE    
  Counter64  

wanFrPvcStatsInOctets 1.3.6.1.4.1.11.2.3.7.6.1.5.1.8.1.3.2.1.6
The sum of octets from all frames seen originating from the far end of the link on this DLCI.
OBJECT-TYPE    
  Counter64  

wanFrPvcStatsOutOctets 1.3.6.1.4.1.11.2.3.7.6.1.5.1.8.1.3.2.1.7
The sum of octets from all frames seen originating from the near end of the link on this DLCI.
OBJECT-TYPE    
  Counter64  

wanFrPvcStatsInFECNs 1.3.6.1.4.1.11.2.3.7.6.1.5.1.8.1.3.2.1.8
The number of frames see coming form the far end of the link with the FECN bit set on this DLCI.
OBJECT-TYPE    
  Counter64  

wanFrPvcStatsOutFECNs 1.3.6.1.4.1.11.2.3.7.6.1.5.1.8.1.3.2.1.9
The number of frames seen coming from the far end of the link with the BECN bit set on this DLCI.
OBJECT-TYPE    
  Counter64  

wanFrPvcStatsInBECNs 1.3.6.1.4.1.11.2.3.7.6.1.5.1.8.1.3.2.1.10
The number of frames see coming form the near end of the link with the FECN bit set.
OBJECT-TYPE    
  Counter64  

wanFrPvcStatsOutBECNs 1.3.6.1.4.1.11.2.3.7.6.1.5.1.8.1.3.2.1.11
The number of frames seen coming from the near end of the link with the BECN bit set on this DLCI.
OBJECT-TYPE    
  Counter64  

wanFrPvcStatsInDEs 1.3.6.1.4.1.11.2.3.7.6.1.5.1.8.1.3.2.1.12
The number of frames seen coming from the far end of the link with the DE bit set on this DCLI.
OBJECT-TYPE    
  Counter64  

wanFrPvcStatsOutDEs 1.3.6.1.4.1.11.2.3.7.6.1.5.1.8.1.3.2.1.13
The number of frames seen coming from the near end of the link with the DE bit set on this DLCI.
OBJECT-TYPE    
  Counter64  

wanFrPvcStatsUpTime 1.3.6.1.4.1.11.2.3.7.6.1.5.1.8.1.3.2.1.14
The total amount of time in one-hundreds of a second that the probe is sure this LCI was active, i.e., the total time the value of wanFrPvcStatsState was equal to up(1). A value of less than the age of this entry does not necessarily mean that this LCI was down. It only means the probe was not certain it was up. Note: the sum of wanFrPvcStatsUpTime and wanFrPvcStatsDownTime may be less than the age of this entry. In this case, the unaccounted for time is the time the probe was uncertain of the state of this DLCI, i.e., the total time the value of wanFrPvcStatsState was unknown(3).
OBJECT-TYPE    
  TimeTicks  

wanFrPvcStatsDownTime 1.3.6.1.4.1.11.2.3.7.6.1.5.1.8.1.3.2.1.15
The total amount of time in one-hundreds of a second that the probe is sure this LCI was down, i.e., the total time the value of wanFrPvcStatsState was equal to down(3). A value of less than the age of this entry does not necessarily mean that this LCI was up at some point. It only means the probe was not certain it was down. Note: the sum of wanX25PvcStatsUpTime and wanFrPvcStatsDownTime may be less than the age of this entry. In this case, the unaccounted for time is the time the probe was uncertain of the state of this DLCI, i.e., the total time the value of wanFrPvcStatsState was unknown(3).
OBJECT-TYPE    
  TimeTicks  

wanFrPvcStatsState 1.3.6.1.4.1.11.2.3.7.6.1.5.1.8.1.3.2.1.16
The current state of this DLCI as inferred by the probe. A value of up(2) means the DLCI is active. A value of down(2) means the DLCI is inactive. And a value of unknown(3) means the probe cannot currently infer the state.
OBJECT-TYPE    
  INTEGER up(1), down(2), unknown(3)  

wanFrPvcStatsStateChanges 1.3.6.1.4.1.11.2.3.7.6.1.5.1.8.1.3.2.1.17
The count of the number of times the wanFrPvcStatsState has gone from up(1) to down(2) or vice versa. The number of times wanFrPvcStatsState goes to unknown(3) is not counted. However, if the value goes from up(1) to unknown(3) and then to down(2) should be counted as 1. Likewise going from down(2) to unknown(3) and then to up(3) should be counted as 1.
OBJECT-TYPE    
  Counter64  

wanFrPvcStatsOwner 1.3.6.1.4.1.11.2.3.7.6.1.5.1.8.1.3.2.1.18
The entity that configured this entry.
OBJECT-TYPE    
  OwnerString  

wanFrPvcStatsStatus 1.3.6.1.4.1.11.2.3.7.6.1.5.1.8.1.3.2.1.19
The status of this wanFrPvcStatsTable entry.
OBJECT-TYPE    
  RowStatus  

wanFrPvcHistoryTable 1.3.6.1.4.1.11.2.3.7.6.1.5.1.8.2.3.2
Frame Relay per-DCLI statistics.
OBJECT-TYPE    
  SEQUENCE OF  
    WanFrPvcHistoryEntry

wanFrPvcHistoryEntry 1.3.6.1.4.1.11.2.3.7.6.1.5.1.8.2.3.2.1
The statistics for a frame relay DLCI. The near end of the link refers to the side of the link that the probe is monitoring. The far end is the side the probe is not on.
OBJECT-TYPE    
  WanFrPvcHistoryEntry  

wanFrPvcHistoryIndex 1.3.6.1.4.1.11.2.3.7.6.1.5.1.8.2.3.2.1.1
The history of which this entry is a port. The history identified by a particular value of this index is the same history as identified by the same value of historyControlIndex.
OBJECT-TYPE    
  INTEGER 1..65535  

wanFrPvcHistorySampleIndex 1.3.6.1.4.1.11.2.3.7.6.1.5.1.8.2.3.2.1.2
An index that uniquely identifies the particular sample this entry represents among all samples associated with the same historyControlEntry. This index starts at 1 and increases by one as each new sample is taken.
OBJECT-TYPE    
  INTEGER 1..2147483647  

wanFrPvcHistoryIntervalStart 1.3.6.1.4.1.11.2.3.7.6.1.5.1.8.2.3.2.1.3
The value of sysUpTime at the start of the interval over which this sample was measured. If the probe keeps track of time of day, it should start the first sample of the history at a time such that when the next hour of the day begins, a sample is started at that instant. Note that following this rule may require the probe to delay collection the first sample of the history, as each sample must be of the same interval. Also note that the sample which is currently being collected is not accessible in this table until the end of its interval.
OBJECT-TYPE    
  TimeTicks  

wanFrPvcHistoryDropEvents 1.3.6.1.4.1.11.2.3.7.6.1.5.1.8.2.3.2.1.4
The change in value of wanFrPvcStatsDropEvents during the interval.
OBJECT-TYPE    
  Counter64  

wanFrPvcHistoryInFrames 1.3.6.1.4.1.11.2.3.7.6.1.5.1.8.2.3.2.1.5
The change in value of wanFrPvcStatsInFrames during the interval.
OBJECT-TYPE    
  Counter64  

wanFrPvcHistoryOutFrames 1.3.6.1.4.1.11.2.3.7.6.1.5.1.8.2.3.2.1.6
The change in value of wanFrPvcStatsOutFrames during the interval.
OBJECT-TYPE    
  Counter64  

wanFrPvcHistoryInOctets 1.3.6.1.4.1.11.2.3.7.6.1.5.1.8.2.3.2.1.7
The change in value of wanFrPvcStatsInOctets during the interval.
OBJECT-TYPE    
  Counter64  

wanFrPvcHistoryOutOctets 1.3.6.1.4.1.11.2.3.7.6.1.5.1.8.2.3.2.1.8
The change in value of wanFrPvcStatsOutOctets during the interval.
OBJECT-TYPE    
  Counter64  

wanFrPvcHistoryInFECNs 1.3.6.1.4.1.11.2.3.7.6.1.5.1.8.2.3.2.1.9
The change in value of wanFrPvcStatsInFECNs during the interval.
OBJECT-TYPE    
  Counter64  

wanFrPvcHistoryOutFECNs 1.3.6.1.4.1.11.2.3.7.6.1.5.1.8.2.3.2.1.10
The change in value of wanFrPvcStatsOutFECNs during the interval.
OBJECT-TYPE    
  Counter64  

wanFrPvcHistoryInBECNs 1.3.6.1.4.1.11.2.3.7.6.1.5.1.8.2.3.2.1.11
The change in value of wanFrPvcStatsInBECNs during the interval.
OBJECT-TYPE    
  Counter64  

wanFrPvcHistoryOutBECNs 1.3.6.1.4.1.11.2.3.7.6.1.5.1.8.2.3.2.1.12
The change in value of wanFrPvcStatsOutBECNs during the interval.
OBJECT-TYPE    
  Counter64  

wanFrPvcHistoryInDEs 1.3.6.1.4.1.11.2.3.7.6.1.5.1.8.2.3.2.1.13
The change in value of wanFrPvcStatsInDEs during the interval.
OBJECT-TYPE    
  Counter64  

wanFrPvcHistoryOutDEs 1.3.6.1.4.1.11.2.3.7.6.1.5.1.8.2.3.2.1.14
The change in value of wanFrPvcStatsOutDEs during the interval.
OBJECT-TYPE    
  Counter64  

wanFrPvcHistoryUpTime 1.3.6.1.4.1.11.2.3.7.6.1.5.1.8.2.3.2.1.15
The change in value of wanFrPvcStatsUpTime during the interval.
OBJECT-TYPE    
  TimeTicks  

wanFrPvcHistoryDownTime 1.3.6.1.4.1.11.2.3.7.6.1.5.1.8.2.3.2.1.16
The change in value of wanFrPvcStatsDownTime during the interval.
OBJECT-TYPE    
  TimeTicks  

wanFrPvcHistoryStateChanges 1.3.6.1.4.1.11.2.3.7.6.1.5.1.8.2.3.2.1.17
The change in value of wanFrPvcStatsStateChanges during the interval.
OBJECT-TYPE    
  Counter64  

wanFrPvcHistoryInUtilization 1.3.6.1.4.1.11.2.3.7.6.1.5.1.8.2.3.2.1.18
The best estimated of the mean utilization of traffic on this DLCI coming from the far end of the link in hundreds of percent of the CIR.
OBJECT-TYPE    
  INTEGER 0..10000  

wanFrPvcHistoryOutUtilization 1.3.6.1.4.1.11.2.3.7.6.1.5.1.8.2.3.2.1.19
The best estimated of the mean utilization of traffic on this DLCI coming from the near end of the link in hundreds of percent of CIR.
OBJECT-TYPE    
  INTEGER 0..10000  

wanAal5PvcStatsTable 1.3.6.1.4.1.11.2.3.7.6.1.5.1.8.1.3.3
AAL/5 per-VPI/VCI statistics.
OBJECT-TYPE    
  SEQUENCE OF  
    WanAal5PvcStatsEntry

wanAal5PvcStatsEntry 1.3.6.1.4.1.11.2.3.7.6.1.5.1.8.1.3.3.1
The statistics for a AAL-5 VCI/VPI. The near end of the link refers to the side of the link that the probe is monitoring. The far end is the side the probe is not on.
OBJECT-TYPE    
  WanAal5PvcStatsEntry  

wanAal5PvcStatsIndex 1.3.6.1.4.1.11.2.3.7.6.1.5.1.8.1.3.3.1.1
The value of this object uniquely identifies this wanAal5PvcStatsTable entry.
OBJECT-TYPE    
  INTEGER 1..65535  

wanAal5PvcStatsDataSource 1.3.6.1.4.1.11.2.3.7.6.1.5.1.8.1.3.3.1.2
This object identifies the source of the data that this wanAal5StatsEntry analyzes. This source can be any pvcEntry that is associated with an ATM interface on this device. In order to identify a particular VPI/VCI, this object shall identify the instance of the pvcIndex object, defined in the PVCCONFIG-MIB.
OBJECT-TYPE    
  OBJECT IDENTIFIER  

wanAal5PvcStatsDropEvents 1.3.6.1.4.1.11.2.3.7.6.1.5.1.8.1.3.3.1.3
The total number of events in which frames were dropped by the probe due to lack of resources. Note that this number is not necessarily the number of frames dropped; it is just the number of times this condition has been detected.
OBJECT-TYPE    
  Counter64  

wanAal5PvcStatsInCells 1.3.6.1.4.1.11.2.3.7.6.1.5.1.8.1.3.3.1.4
The total number of cells for seen coming from the far end of the link on this VPI/VCI.
OBJECT-TYPE    
  Counter64  

wanAal5PvcStatsOutCells 1.3.6.1.4.1.11.2.3.7.6.1.5.1.8.1.3.3.1.5
The total number of cells seen coming from the near end of the link on this VPI/VCI.
OBJECT-TYPE    
  Counter64  

wanAal5PvcStatsInPDUs 1.3.6.1.4.1.11.2.3.7.6.1.5.1.8.1.3.3.1.6
The total number of AAL-5 PDUs seen coming from the far end of the link on this VPI/VCI.
OBJECT-TYPE    
  Counter64  

wanAal5PvcStatsOutPDUs 1.3.6.1.4.1.11.2.3.7.6.1.5.1.8.1.3.3.1.7
The total number of AAL-5 PDUs seen coming from the near end of the link on this VPI/VCI.
OBJECT-TYPE    
  Counter64  

wanAal5PvcStatsInOctets 1.3.6.1.4.1.11.2.3.7.6.1.5.1.8.1.3.3.1.8
The sum of octets from all AAL-5 PDUs seen originating from the far end of the link on this VCI/VPI.
OBJECT-TYPE    
  Counter64  

wanAal5PvcStatsOutOctets 1.3.6.1.4.1.11.2.3.7.6.1.5.1.8.1.3.3.1.9
The sum of octets from all AAL-5 PDUs seen originating from the near end of the link on this VPI/VCI.
OBJECT-TYPE    
  Counter64  

wanAal5PvcStatsInCLP1 1.3.6.1.4.1.11.2.3.7.6.1.5.1.8.1.3.3.1.10
The total number of cells with the CLP bit set seen coming from the far end of the link on this VCI/VPI.
OBJECT-TYPE    
  Counter64  

wanAal5PvcStatsOutCLP1 1.3.6.1.4.1.11.2.3.7.6.1.5.1.8.1.3.3.1.11
The total number of cells with the CLP bit set seen coming from the near end of the link on this VCI/VPI.
OBJECT-TYPE    
  Counter64  

wanAal5PvcStatsInCRCs 1.3.6.1.4.1.11.2.3.7.6.1.5.1.8.1.3.3.1.12
The total number of AAL-5 PDUs with CRC errors seen coming from the far end of the link on this VCI/VPI.
OBJECT-TYPE    
  Counter64  

wanAal5PvcStatsOutCRCs 1.3.6.1.4.1.11.2.3.7.6.1.5.1.8.1.3.3.1.13
The total number of AAL-5 PDUs with CRC errors seen coming from the near end of the link on this VPI/VCI.
OBJECT-TYPE    
  Counter64  

wanAal5PvcStatsInOversizedSDUs 1.3.6.1.4.1.11.2.3.7.6.1.5.1.8.1.3.3.1.14
The number of AAL5 SDUs from the far end of the link that were too large on this VPI/VCI.
OBJECT-TYPE    
  Counter64  

wanAal5PvcStatsOutOversizedSDUs 1.3.6.1.4.1.11.2.3.7.6.1.5.1.8.1.3.3.1.15
The number of AAL5 SDUs from the near end of the link that were too large on this VPI/VCI.
OBJECT-TYPE    
  Counter64  

wanAal5PvcStatsUpTime 1.3.6.1.4.1.11.2.3.7.6.1.5.1.8.1.3.3.1.16
The total amount of time in one-hundreds of a second that the probe is sure this LCI was active, i.e., the total time the value of wanAal5PvcStatsState was equal to up(1). A value of less than the age of this entry does not necessarily mean that this VPI/VCI was down. It only means the probe was not certain it was up. Note: the sum of wanAal5PvcStatsUpTime and wanAal5PvcStatsDownTime may be less than the age of this entry. In this case, the unaccounted for time is the time the probe was uncertain of the state of this VPI/VCI, i.e., the total time the value of wanAal5PvcStatsState was unknown(3).
OBJECT-TYPE    
  TimeTicks  

wanAal5PvcStatsDownTime 1.3.6.1.4.1.11.2.3.7.6.1.5.1.8.1.3.3.1.17
The total amount of time in one-hundreds of a second that the probe is sure this LCI was down, i.e., the total time the value of wanAal5PvcStatsState was equal to down(3). A value of less than the age of this entry does not necessarily mean that this VPI/VCI was up at some point. It only means the probe was not certain it was down. Note: the sum of wanAal5PvcStatsUpTime and wanAal5PvcStatsDownTime may be less than the age of this entry. In this case, the unaccounted for time is the time the probe was uncertain of the state of this VPI/VCI, i.e., the total time the value of wanAal5PvcStatsState was unknown(3).
OBJECT-TYPE    
  TimeTicks  

wanAal5PvcStatsState 1.3.6.1.4.1.11.2.3.7.6.1.5.1.8.1.3.3.1.18
The current state of this VPI/VCI as inferred by the probe. A value of up(2) means the LCI is active. A value of down(2) means the VPI/VCI is inactive. And a value of unknown(3) means the probe cannot currently infer the state.
OBJECT-TYPE    
  INTEGER up(1), down(2), unknown(3)  

wanAal5PvcStatsStateChanges 1.3.6.1.4.1.11.2.3.7.6.1.5.1.8.1.3.3.1.19
The count of the number of times the wanAal5PvcStatsState has gone from up(1) to down(2) or vice versa. The number of times wanAal5PvcStatsState goes to unknown(3) is not counted. However, if the value goes from up(1) to unknown(3) and then to down(2) should be counted as 1. Likewise going from down(2) to unknown(3) and then to up(3) should be counted as 1.
OBJECT-TYPE    
  Counter64  

wanAal5PvcStatsOwner 1.3.6.1.4.1.11.2.3.7.6.1.5.1.8.1.3.3.1.20
The entity that configured this entry.
OBJECT-TYPE    
  OwnerString  

wanAal5PvcStatsStatus 1.3.6.1.4.1.11.2.3.7.6.1.5.1.8.1.3.3.1.21
The status of this wanAal5PvcStatsTable entry.
OBJECT-TYPE    
  RowStatus  

wanAal5PvcHistoryTable 1.3.6.1.4.1.11.2.3.7.6.1.5.1.8.2.3.3
AAL-5 per-VPI/VCI statistics.
OBJECT-TYPE    
  SEQUENCE OF  
    WanAal5PvcHistoryEntry

wanAal5PvcHistoryEntry 1.3.6.1.4.1.11.2.3.7.6.1.5.1.8.2.3.3.1
The statistics for a AAL-5 VCI/VPI. The near end of the link refers to the side of the link that the probe is monitoring. The far end is the side the probe is not on.
OBJECT-TYPE    
  WanAal5PvcHistoryEntry  

wanAal5PvcHistoryIndex 1.3.6.1.4.1.11.2.3.7.6.1.5.1.8.2.3.3.1.1
The history of which this entry is a port. The history identified by a particular value of this index is the same history as identified by the same value of historyControlIndex.
OBJECT-TYPE    
  INTEGER 1..65535  

wanAal5PvcHistorySampleIndex 1.3.6.1.4.1.11.2.3.7.6.1.5.1.8.2.3.3.1.2
An index that uniquely identifies the particular sample this entry represents among all samples associated with the same historyControlEntry. This index starts at 1 and increases by one as each new sample is taken.
OBJECT-TYPE    
  INTEGER 1..2147483647  

wanAal5PvcHistoryIntervalStart 1.3.6.1.4.1.11.2.3.7.6.1.5.1.8.2.3.3.1.3
The value of sysUpTime at the start of the interval over which this sample was measured. If the probe keeps track of time of day, it should start the first sample of the history at a time such that when the next hour of the day begins, a sample is started at that instant. Note that following this rule may require the probe to delay collection the first sample of the history, as each sample must be of the same interval. Also note that the sample which is currently being collected is not accessible in this table until the end of its interval.
OBJECT-TYPE    
  TimeTicks  

wanAal5PvcHistoryDropEvents 1.3.6.1.4.1.11.2.3.7.6.1.5.1.8.2.3.3.1.4
The change in value of wanAal5PvcStatsDropEvents during the interval.
OBJECT-TYPE    
  Counter64  

wanAal5PvcHistoryInCells 1.3.6.1.4.1.11.2.3.7.6.1.5.1.8.2.3.3.1.5
The change in value of wanAal5PvcStatsInCells during the interval.
OBJECT-TYPE    
  Counter64  

wanAal5PvcHistoryOutCells 1.3.6.1.4.1.11.2.3.7.6.1.5.1.8.2.3.3.1.6
The change in value of wanAal5PvcStatsOutCells during the interval.
OBJECT-TYPE    
  Counter64  

wanAal5PvcHistoryInPDUs 1.3.6.1.4.1.11.2.3.7.6.1.5.1.8.2.3.3.1.7
The change in value of wanAal5PvcStatsInPDUs during the interval.
OBJECT-TYPE    
  Counter64  

wanAal5PvcHistoryOutPDUs 1.3.6.1.4.1.11.2.3.7.6.1.5.1.8.2.3.3.1.8
The change in value of wanAal5PvcStatsOutPDUs during the interval.
OBJECT-TYPE    
  Counter64  

wanAal5PvcHistoryInOctets 1.3.6.1.4.1.11.2.3.7.6.1.5.1.8.2.3.3.1.9
The change in value of wanAal5PvcStatsInOctets during the interval.
OBJECT-TYPE    
  Counter64  

wanAal5PvcHistoryOutOctets 1.3.6.1.4.1.11.2.3.7.6.1.5.1.8.2.3.3.1.10
The change in value of wanAal5PvcStatsOutOctets during the interval.
OBJECT-TYPE    
  Counter64  

wanAal5PvcHistoryInCLP1 1.3.6.1.4.1.11.2.3.7.6.1.5.1.8.2.3.3.1.11
The change in value of wanAal5PvcStatsInCLP1 during the interval.
OBJECT-TYPE    
  Counter64  

wanAal5PvcHistoryOutCLP1 1.3.6.1.4.1.11.2.3.7.6.1.5.1.8.2.3.3.1.12
The change in value of wanAal5PvcStatsOutCLP1 during the interval.
OBJECT-TYPE    
  Counter64  

wanAal5PvcHistoryInCRCs 1.3.6.1.4.1.11.2.3.7.6.1.5.1.8.2.3.3.1.13
The change in value of wanAal5PvcStatsInCRCs during the interval.
OBJECT-TYPE    
  Counter64  

wanAal5PvcHistoryOutCRCs 1.3.6.1.4.1.11.2.3.7.6.1.5.1.8.2.3.3.1.14
The change in value of wanAal5PvcStatsOutCRCs during the interval.
OBJECT-TYPE    
  Counter64  

wanAal5PvcHistoryInOversizedSDUs 1.3.6.1.4.1.11.2.3.7.6.1.5.1.8.2.3.3.1.15
The change in value of wanAal5PvcStatsInOversizedSDUs during the interval.
OBJECT-TYPE    
  Counter64  

wanAal5PvcHistoryOutOversizedSDUs 1.3.6.1.4.1.11.2.3.7.6.1.5.1.8.2.3.3.1.16
The change in value of wanAal5PvcStatsOutOversizedSDUs during the interval.
OBJECT-TYPE    
  Counter64  

wanAal5PvcHistoryUpTime 1.3.6.1.4.1.11.2.3.7.6.1.5.1.8.2.3.3.1.17
The change in value of wanAal5PvcStatsUpTime during the interval.
OBJECT-TYPE    
  TimeTicks  

wanAal5PvcHistoryDownTime 1.3.6.1.4.1.11.2.3.7.6.1.5.1.8.2.3.3.1.18
The change in value of wanAal5PvcStatsDownTime during the interval.
OBJECT-TYPE    
  TimeTicks  

wanAal5PvcHistoryStateChanges 1.3.6.1.4.1.11.2.3.7.6.1.5.1.8.2.3.3.1.19
The change in value of wanAal5PvcStatsStateChanges during the interval.
OBJECT-TYPE    
  Counter64  

wanAal5PvcHistoryInUtilization 1.3.6.1.4.1.11.2.3.7.6.1.5.1.8.2.3.3.1.20
The best estimated of the mean utilization of traffic on this VPI/VCI coming from the far end of the link in hundreds of percent of the CIR.
OBJECT-TYPE    
  INTEGER 0..10000  

wanAal5PvcHistoryOutUtilization 1.3.6.1.4.1.11.2.3.7.6.1.5.1.8.2.3.3.1.21
The best estimated of the mean utilization of traffic on this VPI/VCI coming from the near end of the link in hundreds of percent of CIR.
OBJECT-TYPE    
  INTEGER 0..10000