VRRPV3-MIB

File: VRRPV3-MIB.mib (35912 bytes)

Imported modules

SNMPv2-SMI SNMPv2-TC SNMPv2-CONF
IF-MIB INET-ADDRESS-MIB

Imported symbols

MODULE-IDENTITY OBJECT-TYPE NOTIFICATION-TYPE
Counter32 Integer32 mib-2
Unsigned32 Counter64 TimeTicks
TEXTUAL-CONVENTION RowStatus MacAddress
TruthValue TimeStamp TimeInterval
MODULE-COMPLIANCE OBJECT-GROUP NOTIFICATION-GROUP
ifIndex InetAddressType InetAddress

Defined Types

Vrrpv3VrIdTC  
The value of the Virtual Router Identifier noted as (VRID) in RFC 5798. This, along with interface index (ifIndex) and IP version, serves to uniquely identify a virtual router on a given VRRP router.
TEXTUAL-CONVENTION    
  Integer32 1..255  

Vrrpv3OperationsEntry  
SEQUENCE    
  vrrpv3OperationsVrId Vrrpv3VrIdTC
  vrrpv3OperationsInetAddrType InetAddressType
  vrrpv3OperationsMasterIpAddr InetAddress
  vrrpv3OperationsPrimaryIpAddr InetAddress
  vrrpv3OperationsVirtualMacAddr MacAddress
  vrrpv3OperationsStatus INTEGER
  vrrpv3OperationsPriority Unsigned32
  vrrpv3OperationsAddrCount Integer32
  vrrpv3OperationsAdvInterval TimeInterval
  vrrpv3OperationsPreemptMode TruthValue
  vrrpv3OperationsAcceptMode TruthValue
  vrrpv3OperationsUpTime TimeTicks
  vrrpv3OperationsRowStatus RowStatus

Vrrpv3AssociatedIpAddrEntry  
SEQUENCE    
  vrrpv3AssociatedIpAddrAddress InetAddress
  vrrpv3AssociatedIpAddrRowStatus RowStatus

Vrrpv3StatisticsEntry  
SEQUENCE    
  vrrpv3StatisticsMasterTransitions Counter32
  vrrpv3StatisticsNewMasterReason INTEGER
  vrrpv3StatisticsRcvdAdvertisements Counter64
  vrrpv3StatisticsAdvIntervalErrors Counter64
  vrrpv3StatisticsIpTtlErrors Counter64
  vrrpv3StatisticsProtoErrReason INTEGER
  vrrpv3StatisticsRcvdPriZeroPackets Counter64
  vrrpv3StatisticsSentPriZeroPackets Counter64
  vrrpv3StatisticsRcvdInvalidTypePackets Counter64
  vrrpv3StatisticsAddressListErrors Counter64
  vrrpv3StatisticsPacketLengthErrors Counter64
  vrrpv3StatisticsRowDiscontinuityTime TimeStamp
  vrrpv3StatisticsRefreshRate Unsigned32

Defined Values

vrrpv3MIB 1.3.6.1.2.1.207
This MIB describes objects used for managing Virtual Router Redundancy Protocol version 3 (VRRPv3). Copyright (c) 2012 IETF Trust and the persons identified as authors of the code. All rights reserved. Redistribution and use in source and binary forms, with or without modification, is permitted pursuant to, and subject to the license terms contained in, the Simplified BSD License set forth in Section 4.c of the IETF Trust's Legal Provisions Relating to IETF Documents (http://trustee.ietf.org/license-info). This version of the MIB module is part of RFC 6527. Please see the RFC for full legal notices.
MODULE-IDENTITY    

vrrpv3Notifications 1.3.6.1.2.1.207.0
OBJECT IDENTIFIER    

vrrpv3Objects 1.3.6.1.2.1.207.1
OBJECT IDENTIFIER    

vrrpv3Conformance 1.3.6.1.2.1.207.2
OBJECT IDENTIFIER    

vrrpv3Operations 1.3.6.1.2.1.207.1.1
OBJECT IDENTIFIER    

vrrpv3Statistics 1.3.6.1.2.1.207.1.2
OBJECT IDENTIFIER    

vrrpv3OperationsTable 1.3.6.1.2.1.207.1.1.1
Unified Operations table for a VRRP router that consists of a sequence (i.e., one or more conceptual rows) of 'vrrpv3OperationsEntry' items each of which describe the operational characteristics of a virtual router.
Status: current Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    Vrrpv3OperationsEntry

vrrpv3OperationsEntry 1.3.6.1.2.1.207.1.1.1.1
An entry in the vrrpv3OperationsTable containing the operational characteristics of a virtual router. On a VRRP router, a given virtual router is identified by a combination of ifIndex, VRID, and the IP version. ifIndex represents an interface of the router. A row must be created with vrrpv3OperationsStatus set to initialize(1) and cannot transition to backup(2) or master(3) until vrrpv3OperationsRowStatus is transitioned to active(1). The information in this table is persistent and when written the entity SHOULD save the change to non- volatile storage.
Status: current Access: not-accessible
OBJECT-TYPE    
  Vrrpv3OperationsEntry  

vrrpv3OperationsVrId 1.3.6.1.2.1.207.1.1.1.1.1
This object contains the Virtual Router Identifier (VRID).
Status: current Access: not-accessible
OBJECT-TYPE    
  Vrrpv3VrIdTC  

vrrpv3OperationsInetAddrType 1.3.6.1.2.1.207.1.1.1.1.2
The IP address type of Vrrpv3OperationsEntry and Vrrpv3AssociatedIpAddrEntry. This value determines the type for vrrpv3OperationsMasterIpAddr, vrrpv3OperationsPrimaryIpAddr, and vrrpv3AssociatedIpAddrAddress. ipv4(1) and ipv6(2) are the only two values supported in this MIB module.
Status: current Access: not-accessible
OBJECT-TYPE    
  InetAddressType  

vrrpv3OperationsMasterIpAddr 1.3.6.1.2.1.207.1.1.1.1.3
The master router's real IP address. The master router would set this address to vrrpv3OperationsPrimaryIpAddr while transitioning to master state. For backup routers, this is the IP address listed as the source in the VRRP advertisement last received by this virtual router.
Status: current Access: read-only
OBJECT-TYPE    
  InetAddress  

vrrpv3OperationsPrimaryIpAddr 1.3.6.1.2.1.207.1.1.1.1.4
In the case where there is more than one IP Address (associated IP addresses) for a given 'ifIndex', this object is used to specify the IP address that will become the vrrpv3OperationsMasterIpAddr', should the virtual router transition from backup state to master.
Status: current Access: read-create
OBJECT-TYPE    
  InetAddress  

vrrpv3OperationsVirtualMacAddr 1.3.6.1.2.1.207.1.1.1.1.5
The virtual MAC address of the virtual router. Although this object can be derived from the 'vrrpv3OperationsVrId' object, it is defined so that it is easily obtainable by a management application and can be included in VRRP-related SNMP notifications.
Status: current Access: read-only
OBJECT-TYPE    
  MacAddress  

vrrpv3OperationsStatus 1.3.6.1.2.1.207.1.1.1.1.6
The current state of the virtual router. This object has three defined values: - 'initialize', which indicates that the virtual router is waiting for a startup event. - 'backup', which indicates that the virtual router is monitoring the availability of the master router. - 'master', which indicates that the virtual router is forwarding packets for IP addresses that are associated with this router.
Status: current Access: read-only
OBJECT-TYPE    
  INTEGER initialize(1), backup(2), master(3)  

vrrpv3OperationsPriority 1.3.6.1.2.1.207.1.1.1.1.7
This object specifies the priority to be used for the virtual router master election process; higher values imply higher priority. A priority of '0', although not settable, is sent by the master router to indicate that this router has ceased to participate in VRRP, and a backup virtual router should transition to become a new master. A priority of 255 is used for the router that owns the associated IP address(es) for VRRP over IPv4 and hence is not settable. Setting the values of this object to 0 or 255 should be rejected by the agents implementing this MIB module. For example, an SNMP agent would return 'badValue(3)' when a user tries to set the values 0 or 255 for this object.
Status: current Access: read-create
OBJECT-TYPE    
  Unsigned32 0..255  

vrrpv3OperationsAddrCount 1.3.6.1.2.1.207.1.1.1.1.8
The number of IP addresses that are associated with this virtual router. This number is equal to the number of rows in the vrrpv3AssociatedAddrTable that correspond to a given ifIndex/VRID/IP version.
Status: current Access: read-only
OBJECT-TYPE    
  Integer32 0..255  

vrrpv3OperationsAdvInterval 1.3.6.1.2.1.207.1.1.1.1.9
The time interval, in centiseconds, between sending advertisement messages. Only the master router sends VRRP advertisements.
Status: current Access: read-create
OBJECT-TYPE    
  TimeInterval 1..4095  

vrrpv3OperationsPreemptMode 1.3.6.1.2.1.207.1.1.1.1.10
Controls whether a higher priority virtual router will preempt a lower priority master.
Status: current Access: read-create
OBJECT-TYPE    
  TruthValue  

vrrpv3OperationsAcceptMode 1.3.6.1.2.1.207.1.1.1.1.11
Controls whether a virtual router in master state will accept packets addressed to the address owner's IPv6 address as its own if it is not the IPv6 address owner. Default is false(2). This object is not relevant for rows representing VRRP over IPv4 and should be set to false(2).
Status: current Access: read-create
OBJECT-TYPE    
  TruthValue  

vrrpv3OperationsUpTime 1.3.6.1.2.1.207.1.1.1.1.12
This value represents the amount of time, in TimeTicks (hundredth of a second), since this virtual router (i.e., the 'vrrpv3OperationsStatus') transitioned out of 'initialize'.
Status: current Access: read-only
OBJECT-TYPE    
  TimeTicks  

vrrpv3OperationsRowStatus 1.3.6.1.2.1.207.1.1.1.1.13
The RowStatus variable should be used in accordance to installation and removal conventions for conceptual rows. To create a row in this table, a manager sets this object to either createAndGo(4) or createAndWait(5). Until instances of all corresponding columns are appropriately configured, the value of the corresponding instance of the 'vrrpv3OperationsRowStatus' column will be read as notReady(3). In particular, a newly created row cannot be made active(1) until (minimally) the corresponding instance of vrrpv3OperationsInetAddrType, vrrpv3OperationsVrId, and vrrpv3OperationsPrimaryIpAddr has been set, and there is at least one active row in the 'vrrpv3AssociatedIpAddrTable' defining an associated IP address. notInService(2) should be used to administratively bring the row down. A typical order of operation to add a row is: 1. Create a row in vrrpv3OperationsTable with createAndWait(5). 2. Create one or more corresponding rows in vrrpv3AssociatedIpAddrTable. 3. Populate the vrrpv3OperationsEntry. 4. Set vrrpv3OperationsRowStatus to active(1). A typical order of operation to delete an entry is: 1. Set vrrpv3OperationsRowStatus to notInService(2). 2. Set the corresponding rows in vrrpv3AssociatedIpAddrTable to destroy(6) to delete the entry. 3. Set vrrpv3OperationsRowStatus to destroy(6) to delete the entry.
Status: current Access: read-create
OBJECT-TYPE    
  RowStatus  

vrrpv3AssociatedIpAddrTable 1.3.6.1.2.1.207.1.1.2
The table of addresses associated with each virtual router.
Status: current Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    Vrrpv3AssociatedIpAddrEntry

vrrpv3AssociatedIpAddrEntry 1.3.6.1.2.1.207.1.1.2.1
An entry in the table contains an IP address that is associated with a virtual router. The number of rows for a given IP version, VrID, and ifIndex will equal the number of IP addresses associated (e.g., backed up) by the virtual router (equivalent to 'vrrpv3OperationsIpAddrCount'). Rows in the table cannot be modified unless the value of 'vrrpv3OperationsStatus' for the corresponding entry in the vrrpv3OperationsTable has transitioned to initialize(1). The information in this table is persistent and when written the entity SHOULD save the change to non- volatile storage.
Status: current Access: not-accessible
OBJECT-TYPE    
  Vrrpv3AssociatedIpAddrEntry  

vrrpv3AssociatedIpAddrAddress 1.3.6.1.2.1.207.1.1.2.1.1
The assigned IP addresses that a virtual router is responsible for backing up. The IP address type is determined by the value of vrrpv3OperationsInetAddrType in the index of this row.
Status: current Access: not-accessible
OBJECT-TYPE    
  InetAddress Size(0|4|16)  

vrrpv3AssociatedIpAddrRowStatus 1.3.6.1.2.1.207.1.1.2.1.2
The row status variable, used according to installation and removal conventions for conceptual rows. To create a row in this table, a manager sets this object to either createAndGo(4) or createAndWait(5). Setting this object to active(1) results in the addition of an associated address for a virtual router. Setting this object to notInService(2) results in administratively bringing down the row. Destroying the entry or setting it to destroy(6) removes the associated address from the virtual router. The use of other values is implementation-dependent. Implementations should not allow deletion of the last row corresponding to an active row in vrrpv3OperationsTable. Refer to the description of vrrpv3OperationsRowStatus for typical row creation and deletion scenarios.
Status: current Access: read-create
OBJECT-TYPE    
  RowStatus  

vrrpv3RouterChecksumErrors 1.3.6.1.2.1.207.1.2.1
The total number of VRRP packets received with an invalid VRRP checksum value. Discontinuities in the value of this counter can occur at re-initialization of the management system, and at other times as indicated by the value of vrrpv3GlobalStatisticsDiscontinuityTime.
Status: current Access: read-only
OBJECT-TYPE    
  Counter64  

vrrpv3RouterVersionErrors 1.3.6.1.2.1.207.1.2.2
The total number of VRRP packets received with an unknown or unsupported version number. Discontinuities in the value of this counter can occur at re-initialization of the management system, and at other times as indicated by the value of vrrpv3GlobalStatisticsDiscontinuityTime.
Status: current Access: read-only
OBJECT-TYPE    
  Counter64  

vrrpv3RouterVrIdErrors 1.3.6.1.2.1.207.1.2.3
The total number of VRRP packets received with a VRID that is not valid for any virtual router on this router. Discontinuities in the value of this counter can occur at re-initialization of the management system, and at other times as indicated by the value of vrrpv3GlobalStatisticsDiscontinuityTime.
Status: current Access: read-only
OBJECT-TYPE    
  Counter64  

vrrpv3GlobalStatisticsDiscontinuityTime 1.3.6.1.2.1.207.1.2.4
The value of sysUpTime on the most recent occasion at which one of vrrpv3RouterChecksumErrors, vrrpv3RouterVersionErrors, and vrrpv3RouterVrIdErrors suffered a discontinuity. If no such discontinuities have occurred since the last re-initialization of the local management subsystem, then this object contains a zero value.
Status: current Access: read-only
OBJECT-TYPE    
  TimeStamp  

vrrpv3StatisticsTable 1.3.6.1.2.1.207.1.2.5
Table of virtual router statistics.
Status: current Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    Vrrpv3StatisticsEntry

vrrpv3StatisticsEntry 1.3.6.1.2.1.207.1.2.5.1
An entry in the table containing statistics information about a given virtual router.
Status: current Access: not-accessible
OBJECT-TYPE    
  Vrrpv3StatisticsEntry  

vrrpv3StatisticsMasterTransitions 1.3.6.1.2.1.207.1.2.5.1.1
The total number of times that this virtual router's state has transitioned to master state. Discontinuities in the value of this counter can occur at re-initialization of the management system, and at other times as indicated by the value of vrrpv3StatisticsRowDiscontinuityTime.
Status: current Access: read-only
OBJECT-TYPE    
  Counter32  

vrrpv3StatisticsNewMasterReason 1.3.6.1.2.1.207.1.2.5.1.2
This indicates the reason for the virtual router to transition to master state. If the virtual router never transitioned to master state, the value of this object is notMaster(0). Otherwise, this indicates the reason this virtual router transitioned to master state the last time. Used by vrrpv3NewMaster notification.
Status: current Access: read-only
OBJECT-TYPE    
  INTEGER notMaster(0), priority(1), preempted(2), masterNoResponse(3)  

vrrpv3StatisticsRcvdAdvertisements 1.3.6.1.2.1.207.1.2.5.1.3
The total number of VRRP advertisements received by this virtual router. Discontinuities in the value of this counter can occur at re-initialization of the management system, and at other times as indicated by the value of vrrpv3StatisticsRowDiscontinuityTime.
Status: current Access: read-only
OBJECT-TYPE    
  Counter64  

vrrpv3StatisticsAdvIntervalErrors 1.3.6.1.2.1.207.1.2.5.1.4
The total number of VRRP advertisement packets received for which the advertisement interval is different from the vrrpv3OperationsAdvInterval configured on this virtual router. Discontinuities in the value of this counter can occur at re-initialization of the management system, and at other times as indicated by the value of vrrpv3StatisticsRowDiscontinuityTime.
Status: current Access: read-only
OBJECT-TYPE    
  Counter64  

vrrpv3StatisticsIpTtlErrors 1.3.6.1.2.1.207.1.2.5.1.5
The total number of VRRP packets received by the virtual router with IPv4 TTL (for VRRP over IPv4) or IPv6 Hop Limit (for VRRP over IPv6) not equal to 255. Discontinuities in the value of this counter can occur at re-initialization of the management system, and at other times as indicated by the value of vrrpv3StatisticsRowDiscontinuityTime.
Status: current Access: read-only
OBJECT-TYPE    
  Counter64  

vrrpv3StatisticsProtoErrReason 1.3.6.1.2.1.207.1.2.5.1.6
This indicates the reason for the last protocol error. This SHOULD be set to noError(0) when no protocol errors are encountered. Used by vrrpv3ProtoError notification.
Status: current Access: read-only
OBJECT-TYPE    
  INTEGER noError(0), ipTtlError(1), versionError(2), checksumError(3), vrIdError(4)  

vrrpv3StatisticsRcvdPriZeroPackets 1.3.6.1.2.1.207.1.2.5.1.7
The total number of VRRP packets received by the virtual router with a priority of '0'. Discontinuities in the value of this counter can occur at re-initialization of the management system, and at other times as indicated by the value of vrrpv3StatisticsRowDiscontinuityTime.
Status: current Access: read-only
OBJECT-TYPE    
  Counter64  

vrrpv3StatisticsSentPriZeroPackets 1.3.6.1.2.1.207.1.2.5.1.8
The total number of VRRP packets sent by the virtual router with a priority of '0'. Discontinuities in the value of this counter can occur at re-initialization of the management system, and at other times as indicated by the value of vrrpv3StatisticsRowDiscontinuityTime.
Status: current Access: read-only
OBJECT-TYPE    
  Counter64  

vrrpv3StatisticsRcvdInvalidTypePackets 1.3.6.1.2.1.207.1.2.5.1.9
The number of VRRP packets received by the virtual router with an invalid value in the 'type' field. Discontinuities in the value of this counter can occur at re-initialization of the management system, and at other times as indicated by the value of vrrpv3StatisticsRowDiscontinuityTime.
Status: current Access: read-only
OBJECT-TYPE    
  Counter64  

vrrpv3StatisticsAddressListErrors 1.3.6.1.2.1.207.1.2.5.1.10
The total number of packets received for which the address list does not match the locally configured list for the virtual router. Discontinuities in the value of this counter can occur at re-initialization of the management system, and at other times as indicated by the value of vrrpv3StatisticsRowDiscontinuityTime.
Status: current Access: read-only
OBJECT-TYPE    
  Counter64  

vrrpv3StatisticsPacketLengthErrors 1.3.6.1.2.1.207.1.2.5.1.11
The total number of packets received with a packet length less than the length of the VRRP header. Discontinuities in the value of this counter can occur at re-initialization of the management system, and at other times as indicated by the value of vrrpv3StatisticsRowDiscontinuityTime.
Status: current Access: read-only
OBJECT-TYPE    
  Counter64  

vrrpv3StatisticsRowDiscontinuityTime 1.3.6.1.2.1.207.1.2.5.1.12
The value of sysUpTime on the most recent occasion at which any one or more of this entry's counters suffered a discontinuity. If no such discontinuities have occurred since the last re-initialization of the local management subsystem, then this object contains a zero value.
Status: current Access: read-only
OBJECT-TYPE    
  TimeStamp  

vrrpv3StatisticsRefreshRate 1.3.6.1.2.1.207.1.2.5.1.13
The minimum reasonable polling interval for this entry. This object provides an indication of the minimum amount of time required to update the counters in this entry.
Status: current Access: read-only
OBJECT-TYPE    
  Unsigned32  

vrrpv3NewMaster 1.3.6.1.2.1.207.0.1
The newMaster notification indicates that the sending agent has transitioned to master state.
Status: current Access: read-only
NOTIFICATION-TYPE    

vrrpv3ProtoError 1.3.6.1.2.1.207.0.2
The notification indicates that the sending agent has encountered the protocol error indicated by vrrpv3StatisticsProtoErrReason.
Status: current Access: read-only
NOTIFICATION-TYPE    

vrrpv3Compliances 1.3.6.1.2.1.207.2.1
OBJECT IDENTIFIER    

vrrpv3Groups 1.3.6.1.2.1.207.2.2
OBJECT IDENTIFIER    

vrrpv3FullCompliance 1.3.6.1.2.1.207.2.1.1
The compliance statement
Status: current Access: read-only
MODULE-COMPLIANCE    

vrrpv3ReadOnlyCompliance 1.3.6.1.2.1.207.2.1.2
When this MIB module is implemented without support for read-create (i.e., in read-only mode), then such an implementation can claim read-only compliance. Such a device can then be monitored, but cannot be configured with this MIB.
Status: current Access: read-only
MODULE-COMPLIANCE    

vrrpv3OperationsGroup 1.3.6.1.2.1.207.2.2.1
Conformance group for VRRPv3 operations.
Status: current Access: read-only
OBJECT-GROUP    

vrrpv3StatisticsGroup 1.3.6.1.2.1.207.2.2.2
Conformance group for VRRPv3 statistics.
Status: current Access: read-only
OBJECT-GROUP    

vrrpv3StatisticsDiscontinuityGroup 1.3.6.1.2.1.207.2.2.3
Objects providing information about counter discontinuities.
Status: current Access: read-only
OBJECT-GROUP    

vrrpv3InfoGroup 1.3.6.1.2.1.207.2.2.4
Conformance group for objects contained in VRRPv3 notifications.
Status: current Access: read-only
OBJECT-GROUP    

vrrpv3NotificationsGroup 1.3.6.1.2.1.207.2.2.5
The VRRP MIB Notification Group.
Status: current Access: read-only
NOTIFICATION-GROUP    

Generation date: July 28, 2023, 16:18:13, Copyright © 2007 - 2022 - Circitor