VERTICALT1-E1-MIB

File: VERTICALT1-E1-MIB.mib (50957 bytes)

Imported modules

RFC1155-SMI RFC1213-MIB RFC-1212
RFC-1215

Imported symbols

Gauge enterprises DisplayString
OBJECT-TYPE TRAP-TYPE

Defined Types

VDsx1CardEntry  
SEQUENCE    
  vdsx1cardSlotNumber INTEGER
  vdsx1cardType INTEGER
  vdsx1cardDescr INTEGER
  vdsx1cardRevision INTEGER
  vdsx1cardDriverVersion INTEGER
  vdsx1cardIOPortAddress INTEGER
  vdsx1cardErrorLED INTEGER
  vdsx1cardReadyLED INTEGER

VDsx1TrunkEntry  
SEQUENCE    
  vdsx1TrunkIfIndex INTEGER
  vdsx1TrunkIndex INTEGER
  vdsx1TrunkIdentifier DisplayString
  vdsx1TrunkSlotNumber INTEGER
  vdsx1TrunkDeviceNumber INTEGER
  vdsx1TrunkInterrupt INTEGER
  vdsx1TrunkEnabled INTEGER
  vdsx1TrunkMasterPriority INTEGER
  vdsx1TrunkStream INTEGER
  vdsx1TrunkStartingChannel INTEGER
  vdsx1TrunkType INTEGER
  vdsx1TrunkIsdnSignalingProtocol INTEGER
  vdsx1TrunkLineCoding INTEGER
  vdsx1TrunkFraming INTEGER
  vdsx1TrunkDChannelSlot INTEGER
  vdsx1TrunkDChannelDevice INTEGER
  vdsx1TrunkNumberOfChannels INTEGER
  vdsx1TrunkLineBuildOut INTEGER
  vdsx1TrunkLoopback INTEGER
  vdsx1TrunkRedLED INTEGER
  vdsx1TrunkYellowLED INTEGER
  vdsx1TrunkChangePending INTEGER

VDsx1ChannelEntry  
SEQUENCE    
  vdsx1channelIndex INTEGER
  vdsx1channelTrunkIndex INTEGER
  vdsx1channelSlotNumber INTEGER
  vdsx1channelTrunkDeviceNumber INTEGER
  vdsx1channelEnabled INTEGER
  vdsx1channelType INTEGER
  vdsx1channelState INTEGER
  vdsx1channelCallerID DisplayString
  vdsx1channelExternalAddress DisplayString
  vdsx1channelExternalSubAddress DisplayString
  vdsx1channelLocalAddress DisplayString
  vdsx1channelLocalSubAddress DisplayString
  vdsx1channelChangePending INTEGER

Defined Values

vertical 1.3.6.1.4.1.2338
OBJECT IDENTIFIER    

vds1 1.3.6.1.4.1.2338.3
OBJECT IDENTIFIER    

vdsx1CardTable 1.3.6.1.4.1.2338.3.1
The Vertical DS1 Configuration table extension.
Status: mandatory Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    VDsx1CardEntry

vdsx1CardEntry 1.3.6.1.4.1.2338.3.1.1
An entry in the Vertical Card Configuration table (an extension to the rfc1406 Configuration table.
Status: mandatory Access: not-accessible
OBJECT-TYPE    
  VDsx1CardEntry  

vdsx1cardSlotNumber 1.3.6.1.4.1.2338.3.1.1.1
Physical slot in the system in which the card is installed.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER 1..14  

vdsx1cardType 1.3.6.1.4.1.2338.3.1.1.2
The Vertical's card Type. The following types are defined: cardTYPE-DUAL-T1 = 1, cardTYPE-8-CHANNEL-CO-POTS = 3, cardTYPE-BRIDGE1 = 4, cardTYPE-NOT-CONFIGURED = 100
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER cardTYPE-DUAL-T1(1), cardTYPE-8-CHANNEL-CO-POTS(3), cardTYPE-BRIDGE1(4), cardTYPE-NOT-CONFIGURED(100)  

vdsx1cardDescr 1.3.6.1.4.1.2338.3.1.1.3
Vertical card identification number.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER 0..255  

vdsx1cardRevision 1.3.6.1.4.1.2338.3.1.1.4
Vertical card revision level.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER 0..255  

vdsx1cardDriverVersion 1.3.6.1.4.1.2338.3.1.1.5
Vertical card driver version.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER 0..255  

vdsx1cardIOPortAddress 1.3.6.1.4.1.2338.3.1.1.6
The ISA bus base address for this Card.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER 0..7fffffff  

vdsx1cardErrorLED 1.3.6.1.4.1.2338.3.1.1.7
All Vertical cards have an ERROR LED and a READY LED. The combined values of these LEDs are as follows - ERRORLed READYLed VALUE OPERATIONAL DEFINITION OFF OFF (0 0) Invalid state ON OFF (1 0) Just after power up. This state remains until card is ready to service io. ON ON (1 1) Statue during software initialization OFF ON (0 1) The normal operational state of the card.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER 0..1  

vdsx1cardReadyLED 1.3.6.1.4.1.2338.3.1.1.8
All Vertical cards have a READY LED and an ERROR LED. The combined values of these LEDs are as follows - ERRORLed READYLed OPERATIONAL DEFINITION OFF OFF invalid state ON OFF Just after power up. This state remains until card is ready to service io. ON ON Statue during software initialization OFF ON The normal operational state of the card.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER 0..1  

vdsx1TrunkTable 1.3.6.1.4.1.2338.3.2
The DS1 Trunk table extensions for Vertical Networks Instant Office.
Status: mandatory Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    VDsx1TrunkEntry

vdsx1TrunkEntry 1.3.6.1.4.1.2338.3.2.1
An entry in the Vertical DS1 Trunk table
Status: mandatory Access: not-accessible
OBJECT-TYPE    
  VDsx1TrunkEntry  

vdsx1TrunkIfIndex 1.3.6.1.4.1.2338.3.2.1.1
The interface Index for this trunk. The value for this object is equal to the value of dsx1IfIndex from the Interfaces table of DS1/E1 (RFC 1406). Which also correlates to the IfIndex found in MIB-II.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER 1..7fffffff  

vdsx1TrunkIndex 1.3.6.1.4.1.2338.3.2.1.2
This object is the index into the number of trunks associated with the card defined in the card group.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER 1..7fffffff  

vdsx1TrunkIdentifier 1.3.6.1.4.1.2338.3.2.1.3
This value for this object is equal to the value of dsx1CircuitIdentifier from the Configuration table of DS1/E1 (RFC 1406). This is a vendor specific field used to help identify each specific interface for diagnostic purposes.
Status: mandatory Access: read-only
OBJECT-TYPE    
  DisplayString Size(0..255)  

vdsx1TrunkSlotNumber 1.3.6.1.4.1.2338.3.2.1.4
The value for this object is the logical number of the slot in which the card containing this trunk is located, (vdsx1cardSlotNumber).
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER 0..255  

vdsx1TrunkDeviceNumber 1.3.6.1.4.1.2338.3.2.1.5
The value for this object is the logical device number of this trunk within its slot. This number may be used to identify this device in the registry.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER 0..255  

vdsx1TrunkInterrupt 1.3.6.1.4.1.2338.3.2.1.6
Interrupt Request level for this card/trunk. Note: all trunks in the same card have the same IRQ.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER 1..2147483647  

vdsx1TrunkEnabled 1.3.6.1.4.1.2338.3.2.1.7
Setting this variable to Deactivated will disable this particular trunk.
Status: mandatory Access: read-write
OBJECT-TYPE    
  INTEGER vdsx1TrunkActivated(1), vdsx1TrunkNotConfigured(2), vdsx1TrunkDeactivated(100)  

vdsx1TrunkMasterPriority 1.3.6.1.4.1.2338.3.2.1.8
Designates the priority for selecting which trunk is to drive the MVIP SEC8K clock, i.e. which trunk drives the master timing system. This value must be diffrent for each Trunk in the system.Valid values mean: notUsed (100)=> never choose this trunk as clock master primary (1)=> choose this trunk as first choice firstAlternate (2)=> choose this trunk as second choice secondAlternate (3)=> choose this trunk as third choice
Status: mandatory Access: read-write
OBJECT-TYPE    
  INTEGER primary(1), firstAlternate(2), secondAlternate(3), notUsed(100)  

vdsx1TrunkStream 1.3.6.1.4.1.2338.3.2.1.9
The MVIP Stream assigned to the Trunk.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER 0..7  

vdsx1TrunkStartingChannel 1.3.6.1.4.1.2338.3.2.1.10
The starting MVIP channel within the MVIP Stream. If CardType is DTM or WAN1, this value is 0; if CardType is CO-POTS, this value is 16 or 24.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER 0..24  

vdsx1TrunkType 1.3.6.1.4.1.2338.3.2.1.11
Specifies the TrunkType for this trunk. Defines E1 vs T1 as well as Common Channel Signalling (CCS) vs. Channel Associated Signalling (CAS). Valid values are : dev-undef, // 100 : undefined dev-t1CAS, // 1 : T1 Channel Associated Signaling dev-t1CCS, // 2 : T1 Common Channel Signaling : with D channel dev-coPots, // 7 : CO Pots (analog)
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER dev-t1CAS(1), dev-t1CCS(2), dev-coPots(7), dev-undef(100)  

vdsx1TrunkIsdnSignalingProtocol 1.3.6.1.4.1.2338.3.2.1.12
Defines the switch type for the Isdn protocol stack. The following are all the possible types: other(1), none of the following ess4(5), U.S.A. / AT&T 4ESS ess5(6), U.S.A. / AT&T 5ESS dms100(7), U.S.A. / Northern Telecom DMS100 ni2(10), U.S.A. / National ISDN 2 (BRI, PRI) dms100s100 (263) NT DMS-100 switch / S-100
Status: mandatory Access: read-write
OBJECT-TYPE    
  INTEGER other(1), ess4(5), ess5(6), dms100(7), ni2(10), dms100s100(263)  

vdsx1TrunkLineCoding 1.3.6.1.4.1.2338.3.2.1.13
Line Coding, i.e. the zero code suppression used for this Trunk. Valid values are: b8ZS (2) -> use of a specified pattern of normal bits and bipolar violations which are used to replace a sequence of eight zero bits. aMI (5) -> a mode wherein no zero code suppression is present other (6) -> none of the codes described above, or Not Applicable, whichever is appropriate Presently, T1 trunk can be either b8zs (2) or ami (5). E1 trunk must be hdb3 (3).
Status: mandatory Access: read-write
OBJECT-TYPE    
  INTEGER b8zs(2), ami(5), other(6)  

vdsx1TrunkFraming 1.3.6.1.4.1.2338.3.2.1.14
Defines framing for Trunk. T1 trunk can be either esf (2) or d4 (3). E1 trunk can be either e1-crc (5) or e1-mf (6). In cases where Framing is not applicable, value 1 (other) would be displayed.
Status: mandatory Access: read-write
OBJECT-TYPE    
  INTEGER other(1), esf(2), d4(3)  

vdsx1TrunkDChannelSlot 1.3.6.1.4.1.2338.3.2.1.15
Slot number of trunk whose DChannel controls the B channels of this trunk.
Status: mandatory Access: read-write
OBJECT-TYPE    
  INTEGER 1..18  

vdsx1TrunkDChannelDevice 1.3.6.1.4.1.2338.3.2.1.16
Specifies the device number of the trunk whose D channel controls the B channels of this trunk.
Status: mandatory Access: read-write
OBJECT-TYPE    
  INTEGER 1..9  

vdsx1TrunkNumberOfChannels 1.3.6.1.4.1.2338.3.2.1.17
Maximum number of channels to be initialized for this trunk - 0..24 for T1, 0..31 for E1, 0..8 for COPots.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER 0..24  

vdsx1TrunkLineBuildOut 1.3.6.1.4.1.2338.3.2.1.18
Defines the line build out option. The following are applicable values : buildOut-minus15dB , i.e. -15 dB (1), buildOut-0dB , i.e. 0 dB (2), buildOut-minus7point5dB , i.e. -7.5 db (3) .
Status: mandatory Access: read-write
OBJECT-TYPE    
  INTEGER buildOut-minus15dB(1), buildOut-0dB(2), buildOut-minus7point5dB(3), notApplicable(100)  

vdsx1TrunkLoopback 1.3.6.1.4.1.2338.3.2.1.19
This variable represents the loopback confi- guration of the DS1 interface. Agents support- ing read/write access should return badValue in response to a requested loopback state that the interface does not support. The values mean: vdsx1NoLoop Not in the loopback state. A device that is not capable of performing a loopback on the interface shall always return this as it's value. vdsx1PayloadLoop The received signal at this interface is looped through the device. Typically the received signal is looped back for re- transmission after it has passed through the device's framing function. vdsx1LineLoop The received signal at this interface does not go through the device (minimum pene- tration) but is looped back out. vdsx1OtherLoop Loopbacks that are not defined here.
Status: mandatory Access: read-write
OBJECT-TYPE    
  INTEGER vdsx1NoLoop(1), vdsx1PayloadLoop(2), vdsx1LineLoop(3), vdsx1OtherLoop(4)  

vdsx1TrunkRedLED 1.3.6.1.4.1.2338.3.2.1.20
Specifies the RED LED status of the trunk OFF = 0, ON = 1.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER 0..1  

vdsx1TrunkYellowLED 1.3.6.1.4.1.2338.3.2.1.21
Specifies the YELLOW LED status of the trunk OFF = 0, ON = 1.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER 0..1  

vdsx1TrunkChangePending 1.3.6.1.4.1.2338.3.2.1.22
Indicates that a change to the device values have been made to the registry. The intepretation of the values are : 1 => change made to the registry, but not incorporated in the device yet 0 => the device changes the value to 0 from 1, after it incorporates the value from registry.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER 0..1  

vdsx1ChannelTable 1.3.6.1.4.1.2338.3.9
Channel entries for each of the channels associated with each trunk defined in the trunk table.
Status: mandatory Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    VDsx1ChannelEntry

vdsx1ChannelEntry 1.3.6.1.4.1.2338.3.9.1
Each entry is one channel in a T1/E1 trunk.
Status: mandatory Access: not-accessible
OBJECT-TYPE    
  VDsx1ChannelEntry  

vdsx1channelIndex 1.3.6.1.4.1.2338.3.9.1.1
This is the logical channel number of the channel within its trunk. For T1 it is between 1 and 24 for E1 it is between 1 and 32.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER 1..32  

vdsx1channelTrunkIndex 1.3.6.1.4.1.2338.3.9.1.2
This is the index of the trunk (relative to its card) to which this channel belongs.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER 0..255  

vdsx1channelSlotNumber 1.3.6.1.4.1.2338.3.9.1.3
The value for this object is the logical number of the slot in which the card (and trunk) containing is located (vdsx1cardSlotNumber)..
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER 0..255  

vdsx1channelTrunkDeviceNumber 1.3.6.1.4.1.2338.3.9.1.4
The value for this object is the logical device number of the trunk containing this channel within its slot, ie vdsx1TrunkDeviceNumber
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER 0..255  

vdsx1channelEnabled 1.3.6.1.4.1.2338.3.9.1.5
Setting this variable to Deactivated will disable this particular channel. Valid values are : vdsx1channelDeactivated (100) vdsx1channelActivated (1) vdsx1channelNotConfigured (2)
Status: mandatory Access: read-write
OBJECT-TYPE    
  INTEGER vdsx1channelActivated(1), vdsx1channelNotConfigured(2), vdsx1channelDeactivated(100)  

vdsx1channelType 1.3.6.1.4.1.2338.3.9.1.6
Channel type, vdsx1channelTypeUnknown : Unknown type vdsx1channelTypeWink : E&M (Ear and Mouth) start vdsx1channelTypeGS : Ground Start Digital trunk. vdsx1channelTypeClear : Nailed up clear channel, for data vdsx1channelTypeAnalogImm: Analog Trunk, Immediate start vdsx1channelTypeBChan: PRI B channel on T1 or E1 vdsx1channelTypeDChan: PRI D channel on T1 or E1 vdsx1channelTypeAnalogDt: Analog channel, dialtone start vdsx1channelTypeAnalogGs: Analog channel, ground start vdsx1channelTypeDDS: DDS channel (56K or 64K) vdsx1channelTypeAnalogDID: Analog channel, DID wink
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER vdsx1channelTypeWink(2), vdsx1channelTypeGS(5), vdsx1channelTypeClear(6), vdsx1channelTypeAnalogImm(7), vdsx1channelTypeBChan(8), vdsx1channelTypeDChan(9), vdsx1channelTypeAnalogDt(11), vdsx1channelTypeAnalogGs(12), vdsx1channelTypeDDS(13), vdsx1channelTypeAnalogDID(14), vdsx1channelTypeUnknown(100)  

vdsx1channelState 1.3.6.1.4.1.2338.3.9.1.7
The Call State of this particular channel. Valid values are : Out of Service (channelStateOOS - 1), Idle (channelStateIdle - 2), InBound Call (channelStateInCall - 3), OutBound Call (channelStateOutCall - 4), Off line (channelStateOffline - 5), Other state (channelStateOther - 6), Data (channelStateData - 7), Error (channelStateError - 8), Ringing Far End (channelStateFeRinging - 9), Incoming Ringing (channelStateNeRinging - 10), Sending Digits (channelStateDigitSend - 11), Receiving Digits (channelStateDigitRcv - 12), Incall Established (channelStateIncallEst - 13), Outcall Established (channelStateOutcallEst - 14), Incall Clearing (channelStateIncallClear - 15), Outcall Clearing (channelStateOutcallClear - 16).
Status: mandatory Access: read-write
OBJECT-TYPE    
  INTEGER channelStateOOS(1), channelStateIdle(2), channelStateInCall(3), channelStateOutCall(4), channelStateOffline(5), channelStateOther(6), channelStateData(7), channelStateError(8), channelStateFeRinging(9), channelStateNeRinging(10), channelStateDigitSend(11), channelStateDigitRcv(12), channelStateIncallEst(13), channelStateOutcallEst(14), channelStateIncallClear(15), channelStateOutcallClear(16)  

vdsx1channelCallerID 1.3.6.1.4.1.2338.3.9.1.8
The callerID of an incoming caller, if available. If the callerID is not available, then it will have a length of zero
Status: mandatory Access: read-write
OBJECT-TYPE    
  DisplayString Size(0..32)  

vdsx1channelExternalAddress 1.3.6.1.4.1.2338.3.9.1.9
The far end number of a connected call on this channel.If the number is not available, then it will have a length of zero.
Status: mandatory Access: read-write
OBJECT-TYPE    
  DisplayString Size(0..32)  

vdsx1channelExternalSubAddress 1.3.6.1.4.1.2338.3.9.1.10
The far end sub address of a connected call on this channel.If this is not available, then it will have a length of zero
Status: mandatory Access: read-write
OBJECT-TYPE    
  DisplayString Size(0..32)  

vdsx1channelLocalAddress 1.3.6.1.4.1.2338.3.9.1.11
The local number of a connected call on this channel.If the number is not available, then it will have a length of zero
Status: mandatory Access: read-write
OBJECT-TYPE    
  DisplayString Size(0..32)  

vdsx1channelLocalSubAddress 1.3.6.1.4.1.2338.3.9.1.12
The local sub address of a connected call on this channel.If the number is not available, then it will have a length of zero
Status: mandatory Access: read-write
OBJECT-TYPE    
  DisplayString Size(0..32)  

vdsx1channelChangePending 1.3.6.1.4.1.2338.3.9.1.13
Indicates that a change to the channel values have been made to the registry. The intepretation of the values are : 1 => change made to the registry, but not incorporated in the device yet 0 => the device changes the value to 0 from 1, after it incorporates the value from registry.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER 0..1  

vdsx1TrunkRedClear 1
This notification is sent when the specific trunk RED alarm condition clears.
TRAP-TYPE    

vdsx1TrunkRed 2
This notification is sent when the specific trunk goes into the RED alarm situation. Red alarm condition signifies LOS (Loss of Signal) failure, i.e. the receiver sees no positive or negative pulses
TRAP-TYPE    

vdsx1TrunkYellowClear 3
This notification is sent when the specific trunk YELLOW alarm condition clears.
TRAP-TYPE    

vdsx1TrunkYellow 4
This notification is sent when the specific trunk goes into the YELLOW alarm situation. Yellow alarm condition signifies a LOF (Loss of Frame) condition, i.e. the receiver does not see the expected framing pattern.
TRAP-TYPE    

vdsx1TrunkBlueClear 5
This notification is sent when the specific trunk BLUE alarm condition clears.
TRAP-TYPE    

vdsx1TrunkBlue 6
This notification is sent when the specific trunk goes into the BLUE alarm situation. Blue alarm conditions occurs when the source goes into AIS (Alarm indication Signal) state. This means that the source has a problem that prevents it from sending its normal, framed payload. Instead, it sends an unframed stream of 1's.
TRAP-TYPE    

vdsx1TrunkReconfigComplete 7
This notification is sent when the specific trunk successfully reads and incorporates the values from the registry. This is typically done in response to a SET command on any of the Trunk's (or its channel's) read-write parameters
TRAP-TYPE    

vdsx1TrunkReconfigError 8
This notification is sent when the specific trunk fails to incorporate the values read from the registry. Typically, the trunk tries to re-read the registry values in response to a SET command on any of the Trunk's (or its channel's) read-write parameters
TRAP-TYPE    

vdsx1TrunkLoopbackPayloadOn 43
This notification is sent when the specific trunk enters a payload loopback state. Payload loopback means that the received signal at this interface is looped through the device. Typically the received signal is looped back for re- transmission after it has passed through the device's framing function
TRAP-TYPE    

vdsx1TrunkLoopbackPayloadOff 44
This notification is sent when the specific trunk moves from a payload loopback state to a non loopback state.
TRAP-TYPE    

vdsx1TrunkLoopbackLineOn 45
This notification is sent when the specific trunk enters a line loopback state. Under this state the received signal at this interface does not go through the device (minimum penetration) but is looped back out.
TRAP-TYPE    

vdsx1TrunkLoopbackLineOff 46
This notification is sent when the specific trunk goes out of a Line Looped state
TRAP-TYPE