VDSL-LINE-EXT-SCM-MIB

File: VDSL-LINE-EXT-SCM-MIB.mib (15304 bytes)

Imported modules

SNMPv2-SMI SNMPv2-TC SNMPv2-CONF
IF-MIB VDSL-LINE-MIB

Imported symbols

MODULE-IDENTITY OBJECT-TYPE Integer32
transmission Unsigned32 TEXTUAL-CONVENTION
TruthValue RowStatus MODULE-COMPLIANCE
OBJECT-GROUP ifIndex vdslLineConfProfileName

Defined Types

VdslSCMBandId  
This data type is used as the syntax for the VDSL SCM Band Identity. Attributes with this syntax identify the SCM Band referred to. Specified as an INTEGER, the possible values are: optionalBand (1) -- the optional Band range [25kHz - 138kHz] firstDownstreamBand (2) -- first Downstream Band firstUpstreamBand (3) -- first Upstream Band secondDownstreamBand (4) -- second Downstream Band secondUpstreamBand (5) -- second Upstream Band thirdDownstreamBand (6) -- third Downstream Band thirdUpstreamBand (7) -- third Upstream Band
TEXTUAL-CONVENTION    
  INTEGER optionalBand(1), firstDownstreamBand(2), firstUpstreamBand(3), secondDownstreamBand(4), secondUpstreamBand(5), thirdDownstreamBand(6), thirdUpstreamBand(7)  

VdslLineSCMConfProfileBandEntry  
SEQUENCE    
  vdslLineSCMConfProfileBandId VdslSCMBandId
  vdslLineSCMConfProfileBandInUse TruthValue
  vdslLineSCMConfProfileBandCenterFrequency Unsigned32
  vdslLineSCMConfProfileBandSymbolRate Unsigned32
  vdslLineSCMConfProfileBandConstellationSize Unsigned32
  vdslLineSCMConfProfileBandTransmitPSDLevel Unsigned32
  vdslLineSCMConfProfileBandRowStatus RowStatus

VdslLineSCMPhysBandEntry  
SEQUENCE    
  vdslLineSCMPhysBandId VdslSCMBandId
  vdslLineSCMPhysBandInUse TruthValue
  vdslLineSCMPhysBandCurrCenterFrequency Unsigned32
  vdslLineSCMPhysBandCurrSymbolRate Unsigned32
  vdslLineSCMPhysBandCurrConstellationSize Unsigned32
  vdslLineSCMPhysBandCurrPSDLevel Unsigned32
  vdslLineSCMPhysBandCurrSnrMgn Integer32
  vdslLineSCMPhysBandCurrAtn Unsigned32

Defined Values

vdslExtSCMMIB 1.3.6.1.2.1.10.228
The VDSL-LINE-MIB found in RFC 3728 defines objects for the management of a pair of VDSL transceivers at each end of the VDSL line. The VDSL-LINE-MIB configures and monitors the line code independent parameters (TC layer) of the VDSL line. This MIB module is an optional extension of the VDSL-LINE-MIB and defines objects for configuration and monitoring of the line code specific (LCS) elements (PMD layer) for VDSL lines using SCM coding. The objects in this extension MIB MUST NOT be used for VDSL lines using Multiple Carrier Modulation (MCM) line coding. If an object in this extension MIB is referenced by a line which does not use SCM, it has no effect on the operation of that line. Naming Conventions: Vtuc -- VDSL transceiver at near (Central) end of line Vtur -- VDSL transceiver at Remote end of line Vtu -- One of either Vtuc or Vtur Curr -- Current Atn -- Attenuation LCS -- Line Code Specific Max -- Maximum Mgn -- Margin PSD -- Power Spectral Density Rx -- Receive Snr -- Signal to Noise Ratio Tx -- Transmit Copyright (C) The Internet Society (2005). This version of this MIB module is part of RFC 4069: see the RFC itself for full legal notices.
MODULE-IDENTITY    

vdslLineExtSCMMib 1.3.6.1.2.1.10.228.1
OBJECT IDENTIFIER    

vdslLineExtSCMMibObjects 1.3.6.1.2.1.10.228.1.1
OBJECT IDENTIFIER    

vdslLineSCMConfProfileBandTable 1.3.6.1.2.1.10.228.1.1.1
This table contains transmit band descriptor configuration information for a VDSL line. Each entry in this table reflects the configuration for one of possibly many bands of a single carrier modulation (SCM) VDSL line. For each profile which is associated with a VDSL line using SCM line coding, five entries in this table will exist, one for each of the five bands. Bands which are not in use will be marked as unused. These entries are defined by a manager and can be used to configure the VDSL line. If an entry in this table is referenced by a line which does not use SCM, it has no effect on the operation of that line.
Status: current Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    VdslLineSCMConfProfileBandEntry

vdslLineSCMConfProfileBandEntry 1.3.6.1.2.1.10.228.1.1.1.1
Each entry consists of a list of parameters that represents the configuration of a single carrier modulation VDSL modem transmit band. A default profile with an index of 'DEFVAL', will always exist and its parameters will be set to vendor specific values, unless otherwise specified in this document. All read-create objects defined in this MIB module SHOULD be stored persistently.
Status: current Access: not-accessible
OBJECT-TYPE    
  VdslLineSCMConfProfileBandEntry  

vdslLineSCMConfProfileBandId 1.3.6.1.2.1.10.228.1.1.1.1.1
The BandId for this entry, which specifies which band is being referred to.
Status: current Access: not-accessible
OBJECT-TYPE    
  VdslSCMBandId  

vdslLineSCMConfProfileBandInUse 1.3.6.1.2.1.10.228.1.1.1.1.2
Indicates whether this band is in use. If set to True this band is in use.
Status: current Access: read-create
OBJECT-TYPE    
  TruthValue  

vdslLineSCMConfProfileBandCenterFrequency 1.3.6.1.2.1.10.228.1.1.1.1.3
Specifies the center frequency in Hz
Status: current Access: read-create
OBJECT-TYPE    
  Unsigned32  

vdslLineSCMConfProfileBandSymbolRate 1.3.6.1.2.1.10.228.1.1.1.1.4
The requested symbol rate in baud.
Status: current Access: read-create
OBJECT-TYPE    
  Unsigned32  

vdslLineSCMConfProfileBandConstellationSize 1.3.6.1.2.1.10.228.1.1.1.1.5
Specifies the constellation size.
Status: current Access: read-create
OBJECT-TYPE    
  Unsigned32 0..16  

vdslLineSCMConfProfileBandTransmitPSDLevel 1.3.6.1.2.1.10.228.1.1.1.1.6
The requested transmit power spectral density for the VDSL modem. The Actual value in -0.25 dBm/Hz.
Status: current Access: read-create
OBJECT-TYPE    
  Unsigned32  

vdslLineSCMConfProfileBandRowStatus 1.3.6.1.2.1.10.228.1.1.1.1.7
This object is used to create a new row or modify or delete an existing row in this table. A profile activated by setting this object to `active'. When `active' is set, the system will validate the profile. None of the columns in this row may be modified while the row is in the `active' state. Before a profile can be deleted or taken out of service, (by setting this object to `destroy' or `notInService') it must be first unreferenced from all associated lines.
Status: current Access: read-create
OBJECT-TYPE    
  RowStatus  

vdslLineSCMPhysBandTable 1.3.6.1.2.1.10.228.1.1.2
This table provides one row for each SCM Vtu band. This table is read only as it reflects the current physical parameters of each band. For each ifIndex which is associated with a VDSL line using SCM line coding, five entries in this table will exist, one for each of the five bands. Bands which are not in use will be marked as unused.
Status: current Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    VdslLineSCMPhysBandEntry

vdslLineSCMPhysBandEntry 1.3.6.1.2.1.10.228.1.1.2.1
An entry in the vdslLineSCMPhysBandTable.
Status: current Access: not-accessible
OBJECT-TYPE    
  VdslLineSCMPhysBandEntry  

vdslLineSCMPhysBandId 1.3.6.1.2.1.10.228.1.1.2.1.1
The BandId for this entry, which specifies which band is being referred to.
Status: current Access: not-accessible
OBJECT-TYPE    
  VdslSCMBandId  

vdslLineSCMPhysBandInUse 1.3.6.1.2.1.10.228.1.1.2.1.2
Indicates whether this band is in use. If set to True this band is in use.
Status: current Access: read-only
OBJECT-TYPE    
  TruthValue  

vdslLineSCMPhysBandCurrCenterFrequency 1.3.6.1.2.1.10.228.1.1.2.1.3
The current center frequency in Hz for this band.
Status: current Access: read-only
OBJECT-TYPE    
  Unsigned32  

vdslLineSCMPhysBandCurrSymbolRate 1.3.6.1.2.1.10.228.1.1.2.1.4
The current value of the symbol rate in baud for this band.
Status: current Access: read-only
OBJECT-TYPE    
  Unsigned32  

vdslLineSCMPhysBandCurrConstellationSize 1.3.6.1.2.1.10.228.1.1.2.1.5
The current constellation size on this band.
Status: current Access: read-only
OBJECT-TYPE    
  Unsigned32 0..16  

vdslLineSCMPhysBandCurrPSDLevel 1.3.6.1.2.1.10.228.1.1.2.1.6
The transmit power spectral density for the VDSL modem.
Status: current Access: read-only
OBJECT-TYPE    
  Unsigned32  

vdslLineSCMPhysBandCurrSnrMgn 1.3.6.1.2.1.10.228.1.1.2.1.7
Noise margin as seen by this Vtu and band with respect to its received signal in 0.25 dB.
Status: current Access: read-only
OBJECT-TYPE    
  Integer32  

vdslLineSCMPhysBandCurrAtn 1.3.6.1.2.1.10.228.1.1.2.1.8
Measured difference in the total power transmitted by the peer Vtu on this band and the total power received by this Vtu on this band in 0.25 dB.
Status: current Access: read-only
OBJECT-TYPE    
  Unsigned32 0..255  

vdslLineExtSCMConformance 1.3.6.1.2.1.10.228.1.2
OBJECT IDENTIFIER    

vdslLineExtSCMGroups 1.3.6.1.2.1.10.228.1.2.1
OBJECT IDENTIFIER    

vdslLineExtSCMCompliances 1.3.6.1.2.1.10.228.1.2.2
OBJECT IDENTIFIER    

vdslLineExtSCMMibCompliance 1.3.6.1.2.1.10.228.1.2.2.1
The compliance statement for SNMP entities which manage VDSL interfaces.
Status: current Access: read-only
MODULE-COMPLIANCE    

vdslLineExtSCMGroup 1.3.6.1.2.1.10.228.1.2.1.1
A collection of objects providing configuration information for a VDSL line based upon single carrier modulation modem.
Status: current Access: read-only
OBJECT-GROUP