VDSL-LINE-EXT-MCM-MIB
File:
VDSL-LINE-EXT-MCM-MIB.mib (25443 bytes)
Imported modules
Imported symbols
Defined Types
VdslLineMCMConfProfileEntry |
|
SEQUENCE |
|
|
|
|
vdslLineMCMConfProfileTxWindowLength |
Unsigned32 |
|
|
vdslLineMCMConfProfileRowStatus |
RowStatus |
|
VdslLineMCMConfProfileTxBandEntry |
|
SEQUENCE |
|
|
|
|
vdslLineMCMConfProfileTxBandNumber |
Unsigned32 |
|
|
vdslLineMCMConfProfileTxBandStart |
Unsigned32 |
|
|
vdslLineMCMConfProfileTxBandStop |
Unsigned32 |
|
|
vdslLineMCMConfProfileTxBandRowStatus |
RowStatus |
|
VdslLineMCMConfProfileRxBandEntry |
|
SEQUENCE |
|
|
|
|
vdslLineMCMConfProfileRxBandNumber |
Unsigned32 |
|
|
vdslLineMCMConfProfileRxBandStart |
Unsigned32 |
|
|
vdslLineMCMConfProfileRxBandStop |
Unsigned32 |
|
|
vdslLineMCMConfProfileRxBandRowStatus |
RowStatus |
|
VdslLineMCMConfProfileTxPSDEntry |
|
SEQUENCE |
|
|
|
|
vdslLineMCMConfProfileTxPSDNumber |
Unsigned32 |
|
|
vdslLineMCMConfProfileTxPSDTone |
Unsigned32 |
|
|
vdslLineMCMConfProfileTxPSDPSD |
Unsigned32 |
|
|
vdslLineMCMConfProfileTxPSDRowStatus |
RowStatus |
|
VdslLineMCMConfProfileMaxTxPSDEntry |
|
SEQUENCE |
|
|
|
|
vdslLineMCMConfProfileMaxTxPSDNumber |
Unsigned32 |
|
|
vdslLineMCMConfProfileMaxTxPSDTone |
Unsigned32 |
|
|
vdslLineMCMConfProfileMaxTxPSDPSD |
Unsigned32 |
|
|
vdslLineMCMConfProfileMaxTxPSDRowStatus |
RowStatus |
|
VdslLineMCMConfProfileMaxRxPSDEntry |
|
SEQUENCE |
|
|
|
|
vdslLineMCMConfProfileMaxRxPSDNumber |
Unsigned32 |
|
|
vdslLineMCMConfProfileMaxRxPSDTone |
Unsigned32 |
|
|
vdslLineMCMConfProfileMaxRxPSDPSD |
Unsigned32 |
|
|
vdslLineMCMConfProfileMaxRxPSDRowStatus |
RowStatus |
|
Defined Values
vdslExtMCMMIB |
1.3.6.1.2.1.10.229 |
The VDSL-LINE-MIB found in RFC 3728 defines objects for
the management of a pair of VDSL transceivers at each end of
the VDSL line. The VDSL-LINE-MIB configures and monitors the
line code independent parameters (TC layer) of the VDSL line.
This MIB module is an optional extension of the VDSL-LINE-MIB
and defines objects for configuration and monitoring of the
line code specific (LCS) elements (PMD layer) for VDSL lines
using MCM coding. The objects in this extension MIB MUST NOT
be used for VDSL lines using Single Carrier Modulation (SCM)
line coding. If an object in this extension MIB is referenced
by a line which does not use MCM, it has no effect on the
operation of that line.
Naming Conventions:
Vtuc -- (VTUC) transceiver at near (Central) end of line
Vtur -- (VTUR) transceiver at Remote end of line
Vtu -- One of either Vtuc or Vtur
Curr -- Current
LCS -- Line Code Specific
Max -- Maximum
PSD -- Power Spectral Density
Rx -- Receive
Tx -- Transmit
Copyright (C) The Internet Society (2005). This version
of this MIB module is part of RFC 4070: see the RFC
itself for full legal notices. |
MODULE-IDENTITY |
|
|
|
vdslLineMCMConfProfileTable |
1.3.6.1.2.1.10.229.1.1.1 |
This table contains additional information on multiple
carrier VDSL lines. One entry in this table reflects a
profile defined by a manager which can be used to
configure the VDSL line.
If an entry in this table is referenced by a line which
does not use MCM, it has no effect on the operation of that
line.
All read-create-objects defined in this table SHOULD be
stored persistently. |
Status: current |
Access: not-accessible |
OBJECT-TYPE |
|
|
|
|
SEQUENCE OF |
|
|
|
|
VdslLineMCMConfProfileEntry |
|
vdslLineMCMConfProfileEntry |
1.3.6.1.2.1.10.229.1.1.1.1 |
Each entry consists of a list of parameters that
represents the configuration of a multiple carrier
modulation VDSL modem. |
Status: current |
Access: not-accessible |
OBJECT-TYPE |
|
|
|
|
VdslLineMCMConfProfileEntry |
|
|
vdslLineMCMConfProfileTxWindowLength |
1.3.6.1.2.1.10.229.1.1.1.1.1 |
Specifies the length of the transmit window, counted
in samples at the sampling rate corresponding to the
negotiated value of N. |
Status: current |
Access: read-create |
OBJECT-TYPE |
|
|
|
|
Unsigned32 |
1..255 |
|
vdslLineMCMConfProfileRowStatus |
1.3.6.1.2.1.10.229.1.1.1.1.2 |
This object is used to create a new row or modify or
delete an existing row in this table.
A profile is activated by setting this object to `active'.
When `active' is set, the system will validate the profile.
None of the columns in this row may be modified while the
row is in the 'active' state.
Before a profile can be deleted or taken out of
service, (by setting this object to `destroy' or
`notInService') it must first be unreferenced
from all associated lines. |
Status: current |
Access: read-create |
OBJECT-TYPE |
|
|
|
|
RowStatus |
|
|
vdslLineMCMConfProfileTxBandTable |
1.3.6.1.2.1.10.229.1.1.2 |
This table contains transmit band descriptor configuration
information for a VDSL line. Each entry in this table
reflects the configuration for one of possibly many bands
with a multiple carrier modulation (MCM) VDSL line.
These entries are defined by a manager and can be used to
configure the VDSL line.
If an entry in this table is referenced by a line which
does not use MCM, it has no effect on the operation of that
line.
All read-create-objects defined in this table SHOULD be
stored persistently. |
Status: current |
Access: not-accessible |
OBJECT-TYPE |
|
|
|
|
SEQUENCE OF |
|
|
|
|
VdslLineMCMConfProfileTxBandEntry |
|
vdslLineMCMConfProfileTxBandEntry |
1.3.6.1.2.1.10.229.1.1.2.1 |
Each entry consists of a transmit band descriptor, which
is defined by a start and a stop tone index. |
Status: current |
Access: not-accessible |
OBJECT-TYPE |
|
|
|
|
VdslLineMCMConfProfileTxBandEntry |
|
|
vdslLineMCMConfProfileTxBandRowStatus |
1.3.6.1.2.1.10.229.1.1.2.1.4 |
This object is used to create a new row or modify or
delete an existing row in this table.
A profile is activated by setting this object to `active'.
When `active' is set, the system will validate the profile.
Each entry must be internally consistent, the Stop Tone must
be greater than the Start Tone. Each entry must also be
externally consistent, all entries indexed by a specific
profile must not overlap. Validation of the profile will
check both internal and external consistency.
None of the columns in this row may be modified while the
row is in the 'active' state.
Before a profile can be deleted or taken out of
service, (by setting this object to `destroy' or
`notInService') it must be first unreferenced
from all associated lines. |
Status: current |
Access: read-create |
OBJECT-TYPE |
|
|
|
|
RowStatus |
|
|
vdslLineMCMConfProfileRxBandTable |
1.3.6.1.2.1.10.229.1.1.3 |
This table contains receive band descriptor configuration
information for a VDSL line. Each entry in this table
reflects the configuration for one of possibly many bands
with a multiple carrier modulation (MCM) VDSL line.
These entries are defined by a manager and can be used to
configure the VDSL line.
If an entry in this table is referenced by a line which
does not use MCM, it has no effect on the operation of that
line.
All read-create-objects defined in this table SHOULD be
stored persistently. |
Status: current |
Access: not-accessible |
OBJECT-TYPE |
|
|
|
|
SEQUENCE OF |
|
|
|
|
VdslLineMCMConfProfileRxBandEntry |
|
vdslLineMCMConfProfileRxBandEntry |
1.3.6.1.2.1.10.229.1.1.3.1 |
Each entry consists of a transmit band descriptor, which
is defined by a start and a stop tone index. |
Status: current |
Access: not-accessible |
OBJECT-TYPE |
|
|
|
|
VdslLineMCMConfProfileRxBandEntry |
|
|
vdslLineMCMConfProfileRxBandRowStatus |
1.3.6.1.2.1.10.229.1.1.3.1.4 |
This object is used to create a new row or modify or
delete an existing row in this table.
A profile is activated by setting this object to `active'.
When `active' is set, the system will validate the profile.
Each entry must be internally consistent, the Stop Tone must
be greater than the Start Tone. Each entry must also be
externally consistent, all entries indexed by a specific
profile must not overlap. Validation of the profile will
check both internal and external consistency.
None of the columns in this row may be modified while the
row is in the 'active' state.
Before a profile can be deleted or taken out of
service, (by setting this object to `destroy' or
`notInService') it must be first unreferenced
from all associated lines. |
Status: current |
Access: read-create |
OBJECT-TYPE |
|
|
|
|
RowStatus |
|
|
vdslLineMCMConfProfileTxPSDTable |
1.3.6.1.2.1.10.229.1.1.4 |
This table contains transmit PSD mask descriptor
configuration information for a VDSL line. Each entry in
this table reflects the configuration for one tone within
a multiple carrier modulation (MCM) VDSL line. These
entries are defined by a manager and can be used to
configure the VDSL line.
If an entry in this table is referenced by a line which
does not use MCM, it has no effect on the operation of that
line.
All read-create-objects defined in this table SHOULD be
stored persistently. |
Status: current |
Access: not-accessible |
OBJECT-TYPE |
|
|
|
|
SEQUENCE OF |
|
|
|
|
VdslLineMCMConfProfileTxPSDEntry |
|
vdslLineMCMConfProfileTxPSDEntry |
1.3.6.1.2.1.10.229.1.1.4.1 |
Each entry consists of a transmit PSD mask descriptor,
which defines the power spectral density (PSD) for a tone. |
Status: current |
Access: not-accessible |
OBJECT-TYPE |
|
|
|
|
VdslLineMCMConfProfileTxPSDEntry |
|
|
vdslLineMCMConfProfileTxPSDRowStatus |
1.3.6.1.2.1.10.229.1.1.4.1.4 |
This object is used to create a new row or modify or
delete an existing row in this table.
A profile is activated by setting this object to `active'.
When `active' is set, the system will validate the profile.
None of the columns in this row may be modified while the
row is in the 'active' state.
Before a profile can be deleted or taken out of
service, (by setting this object to `destroy' or
`notInService') it must be first unreferenced
from all associated lines. |
Status: current |
Access: read-create |
OBJECT-TYPE |
|
|
|
|
RowStatus |
|
|
vdslLineMCMConfProfileMaxTxPSDTable |
1.3.6.1.2.1.10.229.1.1.5 |
This table contains transmit maximum PSD mask descriptor
configuration information for a VDSL line. Each entry in
this table reflects the configuration for one tone within
a multiple carrier modulation (MCM) VDSL modem. These
entries are defined by a manager and can be used to
configure the VDSL line.
If an entry in this table is referenced by a line which
does not use MCM, it has no effect on the operation of that
line.
All read-create-objects defined in this table SHOULD be
stored persistently. |
Status: current |
Access: not-accessible |
OBJECT-TYPE |
|
|
|
|
SEQUENCE OF |
|
|
|
|
VdslLineMCMConfProfileMaxTxPSDEntry |
|
vdslLineMCMConfProfileMaxTxPSDEntry |
1.3.6.1.2.1.10.229.1.1.5.1 |
Each entry consists of a transmit PSD mask descriptor,
which defines the maximum power spectral density (PSD)
for a tone. |
Status: current |
Access: not-accessible |
OBJECT-TYPE |
|
|
|
|
VdslLineMCMConfProfileMaxTxPSDEntry |
|
|
vdslLineMCMConfProfileMaxTxPSDTone |
1.3.6.1.2.1.10.229.1.1.5.1.2 |
The tone index for which the PSD is being specified.
There must not be multiple rows defined, for a particular
profile, with the same value for this field. |
Status: current |
Access: read-create |
OBJECT-TYPE |
|
|
|
|
Unsigned32 |
1..4096 |
|
vdslLineMCMConfProfileMaxTxPSDRowStatus |
1.3.6.1.2.1.10.229.1.1.5.1.4 |
This object is used to create a new row or modify or
delete an existing row in this table.
A profile is activated by setting this object to `active'.
When `active' is set, the system will validate the profile.
There must be only one entry in this table for each tone
associated with a specific profile. This will be checked
during the validation process.
None of the columns in this row may be modified while the
row is in the 'active' state.
Before a profile can be deleted or taken out of
service, (by setting this object to `destroy' or
`notInService') it must be first unreferenced
from all associated lines. |
Status: current |
Access: read-create |
OBJECT-TYPE |
|
|
|
|
RowStatus |
|
|
vdslLineMCMConfProfileMaxRxPSDTable |
1.3.6.1.2.1.10.229.1.1.6 |
This table contains maximum receive PSD mask descriptor
configuration information for a VDSL line. Each entry in
this table reflects the configuration for one tone within
a multiple carrier modulation (MCM) VDSL modem. These
entries are defined by a manager and can be used to
configure the VDSL line.
If an entry in this table is referenced by a line which
does not use MCM, it has no effect on the operation of that
line.
All read-create-objects defined in this table SHOULD be
stored persistently. |
Status: current |
Access: not-accessible |
OBJECT-TYPE |
|
|
|
|
SEQUENCE OF |
|
|
|
|
VdslLineMCMConfProfileMaxRxPSDEntry |
|
vdslLineMCMConfProfileMaxRxPSDEntry |
1.3.6.1.2.1.10.229.1.1.6.1 |
Each entry consists of a transmit PSD mask descriptor,
which defines the power spectral density (PSD) for a
tone. |
Status: current |
Access: not-accessible |
OBJECT-TYPE |
|
|
|
|
VdslLineMCMConfProfileMaxRxPSDEntry |
|
|
vdslLineMCMConfProfileMaxRxPSDTone |
1.3.6.1.2.1.10.229.1.1.6.1.2 |
The tone index for which the PSD is being specified.
There must not be multiple rows defined, for a particular
profile, with the same value for this field. |
Status: current |
Access: read-create |
OBJECT-TYPE |
|
|
|
|
Unsigned32 |
1..4096 |
|
vdslLineMCMConfProfileMaxRxPSDRowStatus |
1.3.6.1.2.1.10.229.1.1.6.1.4 |
This object is used to create a new row or modify or
delete an existing row in this table.
A profile is activated by setting this object to `active'.
When `active' is set, the system will validate the profile.
There must be only one entry in this table for each tone
associated with a specific profile. This will be checked
during the validation process.
None of the columns in this row may be modified while the
row is in the 'active' state.
Before a profile can be deleted or taken out of
service, (by setting this object to `destroy' or
`notInService') it must be first unreferenced
from all associated lines. |
Status: current |
Access: read-create |
OBJECT-TYPE |
|
|
|
|
RowStatus |
|
|
vdslLineExtMCMMibCompliance |
1.3.6.1.2.1.10.229.1.2.2.1 |
The compliance statement for SNMP entities which
manage VDSL interfaces. |
Status: current |
Access: read-create |
MODULE-COMPLIANCE |
|
|
|
vdslLineExtMCMGroup |
1.3.6.1.2.1.10.229.1.2.1.1 |
A collection of objects providing configuration
information for a VDSL line based upon multiple
carrier modulation modem. |
Status: current |
Access: read-create |
OBJECT-GROUP |
|
|
|