Unisphere-Data-PIM-MIB

File: Unisphere-Data-PIM-MIB.mib (63871 bytes)

Imported modules

SNMPv2-SMI SNMPv2-TC SNMPv2-CONF
PIM-MIB IF-MIB Unisphere-Data-MIBs

Imported symbols

MODULE-IDENTITY OBJECT-TYPE Integer32
IpAddress TimeTicks RowStatus
TruthValue TEXTUAL-CONVENTION MODULE-COMPLIANCE
OBJECT-GROUP pimInterfaceIfIndex pimRPSetComponent
pimRPSetGroupAddress pimRPSetGroupMask pimRPSetAddress
InterfaceIndex usDataMibs

Defined Types

UsdPimType  
This data type is used do identify Sparse mode and Dense mode PIM protocol.
TEXTUAL-CONVENTION    
  INTEGER invalid(0), dense(1), sparse(2), sparseAndDense(3)  

UsdPimInterfaceEntry  
SEQUENCE    
  usdPimIntfNumHelloRcvd Integer32
  usdPimIntfNumJoinPruneRcvd Integer32
  usdPimIntfNumAssertRcvd Integer32
  usdPimIntfNumGraftRcvd Integer32
  usdPimIntfNumGraftAckRcvd Integer32
  usdPimIntfNumHelloSent Integer32
  usdPimIntfNumJoinPruneSent Integer32
  usdPimIntfNumAssertSent Integer32
  usdPimIntfNumGraftSent Integer32
  usdPimIntfNumGraftAckSent Integer32
  usdPimIntfVersion INTEGER
  usdPimIntfNumNbrs Integer32

UsdPimMRouteEntry  
SEQUENCE    
  usdPimMRouteGroup IpAddress
  usdPimMRouteSource IpAddress
  usdPimMRouteSourceMask IpAddress
  usdPimMRouteRPAddress IpAddress
  usdPimMRouteUpstreamAssertTimer TimeTicks
  usdPimMRouteAssertMetric Integer32
  usdPimMRouteAssertPref Integer32
  usdPimMRouteAssertRPTBit TruthValue
  usdPimMRouteBits BITS
  usdPimMRouteRPAddrInUse IpAddress
  usdPimMRouteUpstreamNbr IpAddress
  usdPimMRouteIifAddr IpAddress
  usdPimMRouteIsWaitingToSwitchToSPT TruthValue
  usdPimMRouteEntryExpiryTimer TimeTicks
  usdPimMRouteSenderDRAddr IpAddress
  usdPimMRouteRouteAddr IpAddress
  usdPimMRouteRouteMask IpAddress
  usdPimMRouteGRPAddr IpAddress
  usdPimMRouteGRPMask IpAddress
  usdPimMRouteOtherProtoOifJoinTypeAll TruthValue
  usdPimMRouteOtherProtoOifJoinTypeG TruthValue
  usdPimMRouteOtherProtoOifJoinTypeSG TruthValue
  usdPimMRoutePimType UsdPimType

UsdPimMRouteNextHopEntry  
SEQUENCE    
  usdPimMRouteNextHopGroupAddr IpAddress
  usdPimMRouteNextHopSrcAddr IpAddress
  usdPimMRouteNextHopSrcMask IpAddress
  usdPimMRouteNextHopRPAddr IpAddress
  usdPimMRouteNextHopIfId InterfaceIndex
  usdPimMRouteNextHopAddress IpAddress
  usdPimMRouteNextHopPruneReason INTEGER
  usdPimMRouteNextHopJoinTypeSSRP TruthValue
  usdPimMRouteNextHopJoinTypeG TruthValue
  usdPimMRouteNextHopJoinTypeSG TruthValue
  usdPimMRouteNextHopHasLGM TruthValue
  usdPimMRouteNextHopHasOifAW TruthValue
  usdPimMRouteNextHopHasOifSendAssert TruthValue
  usdPimMRouteNextHopHasOifRegister TruthValue
  usdPimMRouteNextHopHasOifBorderBit TruthValue
  usdPimMRouteNextHopHasOifNullEncapsBit TruthValue
  usdPimMRouteNextHopJoinEndTimer TimeTicks
  usdPimMRouteNextHopAssertEndTimer TimeTicks
  usdPimMRouteNextHopNextAssertTimer TimeTicks
  usdPimMRouteNextHopAssertSrcAddress IpAddress
  usdPimMRouteNextHopRegisterSuppressionTimer TimeTicks
  usdPimMRouteNextHopPimType UsdPimType
  usdPimMRouteNextHopPruneTimeLeft TimeTicks
  usdPimMRouteNextHopsendingIpAddress IpAddress

UsdPimRPSetEntry  
SEQUENCE    
  usdPimRPSetPriority Integer32
  usdPimRPSetTypeInfo INTEGER
  usdPimRPSetAccessListName OCTET STRING

UsdPimStaticRPConfEntry  
SEQUENCE    
  usdPimStaticRPConfComponentIndex Integer32
  usdPimStaticRPConfRPAddr IpAddress
  usdPimStaticRPConfAccessListName OCTET STRING
  usdPimStaticRPConfRowStatus RowStatus
  usdPimStaticRPConfOverride TruthValue

UsdPimAutoRPConfEntry  
SEQUENCE    
  usdPimAutoRPConfComponentIndex Integer32
  usdPimAutoRPConfCandRPAddr IpAddress
  usdPimAutoRPConfGroupAccessListName OCTET STRING
  usdPimAutoRPConfRowStatus RowStatus
  usdPimAutoRPConfTTL Integer32
  usdPimAutoRPConfAncmntIntvl TimeTicks
  usdPimAutoRPConfifId InterfaceIndex

UsdPimAutoRPCandEntry  
SEQUENCE    
  usdPimAutoRPCandComponentIndex Integer32
  usdPimAutoRPCandRPAddr IpAddress
  usdPimAutoRPCandGroupAddr IpAddress
  usdPimAutoRPCandGroupMask IpAddress
  usdPimAutoRPCandRowStatus RowStatus
  usdPimAutoRPCandAccessListName OCTET STRING
  usdPimAutoRPCandAutoRPTTL Integer32
  usdPimAutoRPCandAutoRPAncmntIntvl TimeTicks
  usdPimAutoRPCandIfId InterfaceIndex

UsdPimComponentEntry  
SEQUENCE    
  usdPimComponentIndex Integer32
  usdPimComponentAutoRPMappingAgentRowStatus RowStatus
  usdPimComponentConfiguredAutoRPMappingAgentIfId InterfaceIndex
  usdPimComponentAutoRPMappingAgentInterval TimeTicks
  usdPimComponentAutoRPMappingTTL Integer32
  usdPimComponentAutoRPMappingAgentIntfAddr IpAddress
  usdPimComponentAutoRPMappingAgentWinnerAddr IpAddress
  usdPimComponentAutoRPMappingAgentWinnerLastHeard TimeTicks

UsdPimUnicastRouteEntry  
SEQUENCE    
  usdPimUnicastRouteEntryAddr IpAddress
  usdPimUnicastRouteEntryMask IpAddress
  usdPimUnicastRouteEntryRpfNbr IpAddress
  usdPimUnicastRouteEntryIifId InterfaceIndex
  usdPimUnicastRouteEntryIifAddr IpAddress
  usdPimUnicastRouteEntryPref Integer32
  usdPimUnicastRouteEntryMetric Integer32
  usdPimUnicastRouteEntryPimType UsdPimType

UsdPimSPTThresholdEntry  
SEQUENCE    
  usdPimSPTThresholdAccessListName OCTET STRING
  usdPimSPTThresHoldRowStatus RowStatus
  usdPimSPTThresholdKbps Integer32

Defined Values

usdPimMIB 1.3.6.1.4.1.4874.2.2.43
The enterprise MIB module for management of PIM routers.
MODULE-IDENTITY    

usdPimMIBObjects 1.3.6.1.4.1.4874.2.2.43.1
OBJECT IDENTIFIER    

usdPimTraps 1.3.6.1.4.1.4874.2.2.43.1.0
OBJECT IDENTIFIER    

usdPimGlobal 1.3.6.1.4.1.4874.2.2.43.1.1
OBJECT IDENTIFIER    

usdPimNumHelloRcvd 1.3.6.1.4.1.4874.2.2.43.1.1.1
Total number of Hellos received by PIM on this router.
Status: current Access: read-only
OBJECT-TYPE    
  Integer32  

usdPimNumJoinPruneRcvd 1.3.6.1.4.1.4874.2.2.43.1.1.2
Total number of JoinPrunes received by PIM on this router.
Status: current Access: read-only
OBJECT-TYPE    
  Integer32  

usdPimNumAssertRcvd 1.3.6.1.4.1.4874.2.2.43.1.1.3
Total number of Asserts received by PIM on this router.
Status: current Access: read-only
OBJECT-TYPE    
  Integer32  

usdPimNumGraftRcvd 1.3.6.1.4.1.4874.2.2.43.1.1.4
Total number of Grafts received by PIM on this router.
Status: current Access: read-only
OBJECT-TYPE    
  Integer32  

usdPimNumGraftAckRcvd 1.3.6.1.4.1.4874.2.2.43.1.1.5
Total number of Graft Acks received by PIM on this router.
Status: current Access: read-only
OBJECT-TYPE    
  Integer32  

usdPimNumHelloSent 1.3.6.1.4.1.4874.2.2.43.1.1.6
Total number of Hellos sent by PIM on this router.
Status: current Access: read-only
OBJECT-TYPE    
  Integer32  

usdPimNumJoinPruneSent 1.3.6.1.4.1.4874.2.2.43.1.1.7
Total number of JoinPrunes sent by PIM on this router.
Status: current Access: read-only
OBJECT-TYPE    
  Integer32  

usdPimNumAssertSent 1.3.6.1.4.1.4874.2.2.43.1.1.8
Total number of Asserts sent by PIM on this router.
Status: current Access: read-only
OBJECT-TYPE    
  Integer32  

usdPimNumGraftSent 1.3.6.1.4.1.4874.2.2.43.1.1.9
Total number of Grafts sent by PIM on this router.
Status: current Access: read-only
OBJECT-TYPE    
  Integer32  

usdPimNumGraftAckSent 1.3.6.1.4.1.4874.2.2.43.1.1.10
Total number of Graft Acks sent by PIM on this router.
Status: current Access: read-only
OBJECT-TYPE    
  Integer32  

usdPimInterfaceTable 1.3.6.1.4.1.4874.2.2.43.1.1.11
The (conceptual) table listing enterprise specific information on a subset of the rows of the pimInterfaceTable defined in the standard PIM MIB.
Status: current Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    UsdPimInterfaceEntry

usdPimInterfaceEntry 1.3.6.1.4.1.4874.2.2.43.1.1.11.1
An entry (conceptual row) in the usdPimInterfaceTable. There is one entry per entry in the pimInterfaceTable.
Status: current Access: not-accessible
OBJECT-TYPE    
  UsdPimInterfaceEntry  

usdPimIntfNumHelloRcvd 1.3.6.1.4.1.4874.2.2.43.1.1.11.1.1
Total number of Hellos received by PIM on this interface. It can only be cleared to 0 when doing set. Setting this also sets counters for other types of packets to 0.
Status: current Access: read-write
OBJECT-TYPE    
  Integer32  

usdPimIntfNumJoinPruneRcvd 1.3.6.1.4.1.4874.2.2.43.1.1.11.1.2
Total number of JoinPrunes received by PIM on this interface. It can only be cleared to 0 when doing set. Setting this also sets counters for other types of packets to 0.
Status: current Access: read-write
OBJECT-TYPE    
  Integer32  

usdPimIntfNumAssertRcvd 1.3.6.1.4.1.4874.2.2.43.1.1.11.1.3
Total number of Asserts received by PIM on this interface. It can only be cleared to 0 when doing set. Setting this also sets counters for other types of packets to 0.
Status: current Access: read-write
OBJECT-TYPE    
  Integer32  

usdPimIntfNumGraftRcvd 1.3.6.1.4.1.4874.2.2.43.1.1.11.1.4
Total number of Grafts received by PIM on this interface. It can only be cleared to 0 when doing set. Setting this also sets counters for other types of packets to 0.
Status: current Access: read-write
OBJECT-TYPE    
  Integer32  

usdPimIntfNumGraftAckRcvd 1.3.6.1.4.1.4874.2.2.43.1.1.11.1.5
Total number of Graft Acks received by PIM on this interface. It can only be cleared to 0 when doing set. Setting this also sets counters for other types of packets to 0.
Status: current Access: read-write
OBJECT-TYPE    
  Integer32  

usdPimIntfNumHelloSent 1.3.6.1.4.1.4874.2.2.43.1.1.11.1.6
Total number of Hellos sent by PIM on this interface. It can only be cleared to 0 when doing set. Setting this also sets counters for other types of packets to 0.
Status: current Access: read-write
OBJECT-TYPE    
  Integer32  

usdPimIntfNumJoinPruneSent 1.3.6.1.4.1.4874.2.2.43.1.1.11.1.7
Total number of JoinPrunes sent by PIM on this interface. It can only be cleared to 0 when doing set. Setting this also sets counters for other types of packets to 0.
Status: current Access: read-write
OBJECT-TYPE    
  Integer32  

usdPimIntfNumAssertSent 1.3.6.1.4.1.4874.2.2.43.1.1.11.1.8
Total number of Asserts sent by PIM on this interface. It can only be cleared to 0 when doing set. Setting this also sets counters for other types of packets to 0.
Status: current Access: read-write
OBJECT-TYPE    
  Integer32  

usdPimIntfNumGraftSent 1.3.6.1.4.1.4874.2.2.43.1.1.11.1.9
Total number of Grafts sent by PIM on this interface. It can only be cleared to 0 when doing set. Setting this also sets counters for other types of packets to 0.
Status: current Access: read-write
OBJECT-TYPE    
  Integer32  

usdPimIntfNumGraftAckSent 1.3.6.1.4.1.4874.2.2.43.1.1.11.1.10
Total number of Graft Acks sent by PIM on this interface. It can only be cleared to 0 when doing set. Setting this also sets counters for other types of packets to 0.
Status: current Access: read-write
OBJECT-TYPE    
  Integer32  

usdPimIntfVersion 1.3.6.1.4.1.4874.2.2.43.1.1.11.1.11
The version of PIM running on this interface.
Status: current Access: read-only
OBJECT-TYPE    
  INTEGER 1..2147483647  

usdPimIntfNumNbrs 1.3.6.1.4.1.4874.2.2.43.1.1.11.1.12
Number of PIM neighbors detected on this interface.
Status: current Access: read-only
OBJECT-TYPE    
  Integer32  

usdPimMRouteTable 1.3.6.1.4.1.4874.2.2.43.1.1.12
The (conceptual) table listing PIM multicast routing information describing its <*, *, RP>/ <*, G>/ states.
Status: current Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    UsdPimMRouteEntry

usdPimMRouteEntry 1.3.6.1.4.1.4874.2.2.43.1.1.12.1
An entry (conceptual row) in the usdPimMRouteTable.
Status: current Access: not-accessible
OBJECT-TYPE    
  UsdPimMRouteEntry  

usdPimMRouteGroup 1.3.6.1.4.1.4874.2.2.43.1.1.12.1.1
The group address. Specified as 224.0.0.0 for <*, *, RP> entries.
Status: current Access: not-accessible
OBJECT-TYPE    
  IpAddress  

usdPimMRouteSource 1.3.6.1.4.1.4874.2.2.43.1.1.12.1.2
The source address. Specified as 0.0.0.0 for <*, *, RP> and <*, G> entries.
Status: current Access: not-accessible
OBJECT-TYPE    
  IpAddress  

usdPimMRouteSourceMask 1.3.6.1.4.1.4874.2.2.43.1.1.12.1.3
The source address mask. Specified as 255.255.255.255 for entries and 0.0.0.0 for <*, *, RP> and <*, G> entries.
Status: current Access: not-accessible
OBJECT-TYPE    
  IpAddress  

usdPimMRouteRPAddress 1.3.6.1.4.1.4874.2.2.43.1.1.12.1.4
The RP address used for <*, *, RP>. Specified as 0.0.0.0 for and <*, G> entries.
Status: current Access: not-accessible
OBJECT-TYPE    
  IpAddress  

usdPimMRouteUpstreamAssertTimer 1.3.6.1.4.1.4874.2.2.43.1.1.12.1.5
The time remaining before the router changes its upstream neighbor back to its RPF neighbor. This timer is called the Assert timer in the PIM Sparse and Dense mode specification. A value of 0 indicates that no Assert has changed the upstream neighbor away from the RPF neighbor.
Status: current Access: read-only
OBJECT-TYPE    
  TimeTicks  

usdPimMRouteAssertMetric 1.3.6.1.4.1.4874.2.2.43.1.1.12.1.6
The metric advertised by the assert winner on the upstream interface, or 0 if no such assert is in received.
Status: current Access: read-only
OBJECT-TYPE    
  Integer32  

usdPimMRouteAssertPref 1.3.6.1.4.1.4874.2.2.43.1.1.12.1.7
The preference advertised by the assert winner on the upstream interface, or 0 if no such assert is in effect.
Status: current Access: read-only
OBJECT-TYPE    
  Integer32  

usdPimMRouteAssertRPTBit 1.3.6.1.4.1.4874.2.2.43.1.1.12.1.8
The value of the RPT-bit advertised by the assert winner on the upstream interface, or false if no such assert is in effect.
Status: current Access: read-only
OBJECT-TYPE    
  TruthValue  

usdPimMRouteBits 1.3.6.1.4.1.4874.2.2.43.1.1.12.1.9
This object describes whether the entry is on shared tree (rpt) or shortest path tree (spt).
Status: current Access: read-only
OBJECT-TYPE    
  BITS rpt(0), spt(1)  

usdPimMRouteRPAddrInUse 1.3.6.1.4.1.4874.2.2.43.1.1.12.1.10
The RP Address being used for the RPT/<*, G>/<*, *, RP> entries. Set to 0.0.0.0 for entries on shortest path tree.
Status: current Access: read-only
OBJECT-TYPE    
  IpAddress  

usdPimMRouteUpstreamNbr 1.3.6.1.4.1.4874.2.2.43.1.1.12.1.11
The address of upstream neighbor being used for the entry. Its set to 0.0.0.0 if the router is directly attached to source on one of its interface.
Status: current Access: read-only
OBJECT-TYPE    
  IpAddress  

usdPimMRouteIifAddr 1.3.6.1.4.1.4874.2.2.43.1.1.12.1.12
The address of incoming interface for this entry.
Status: current Access: read-only
OBJECT-TYPE    
  IpAddress  

usdPimMRouteIsWaitingToSwitchToSPT 1.3.6.1.4.1.4874.2.2.43.1.1.12.1.13
This object describes whether the entry is still waiting to switch completely to shortest path tree in case of entries. It waits to do this till it receives first packet from incoming interface towards shortest path tree.
Status: current Access: read-only
OBJECT-TYPE    
  TruthValue  

usdPimMRouteEntryExpiryTimer 1.3.6.1.4.1.4874.2.2.43.1.1.12.1.14
The time after which the entry timer expires for this entry. Set to 0 if entry timer is not active.
Status: current Access: read-only
OBJECT-TYPE    
  TimeTicks  

usdPimMRouteSenderDRAddr 1.3.6.1.4.1.4874.2.2.43.1.1.12.1.15
The address of the designated router on the sender's subnet in case of entries. The sender designated router register encapsulates data to RP. Set to 0.0.0.0 for <*, G> and <*, *, RP> entries.
Status: current Access: read-only
OBJECT-TYPE    
  IpAddress  

usdPimMRouteRouteAddr 1.3.6.1.4.1.4874.2.2.43.1.1.12.1.16
The address of the route being used to do RPF check for this entry. It is set to 0.0.0.0 (with usdPimMRouteRouteMask set to 255.255.255.255) if there is no route available.
Status: current Access: read-only
OBJECT-TYPE    
  IpAddress  

usdPimMRouteRouteMask 1.3.6.1.4.1.4874.2.2.43.1.1.12.1.17
The mask of the route being used to do RPF check for this entry. It is set to 255.255.255.255 (with usdPimMRouteRoute set to 0.0.0.0) if there is no route available.
Status: current Access: read-only
OBJECT-TYPE    
  IpAddress  

usdPimMRouteGRPAddr 1.3.6.1.4.1.4874.2.2.43.1.1.12.1.18
The address of the group-to-RP mapping being used to get the RP for this entry. It is set to 0.0.0.0 (with usdPimMRouteGRPMask set to 0.0.0.0) if there is no group-to-RP mapping available or if entry is <*, *, RP>.
Status: current Access: read-only
OBJECT-TYPE    
  IpAddress  

usdPimMRouteGRPMask 1.3.6.1.4.1.4874.2.2.43.1.1.12.1.19
The mask of the group-to-RP mapping being used to get the RP for this entry. It is set to 255.255.255.255 (with usdPimMRouteGRPAddr set to 0.0.0.0) if there is no group-to-RP mapping available or if entry is <*, *, RP>.
Status: current Access: read-only
OBJECT-TYPE    
  IpAddress  

usdPimMRouteOtherProtoOifJoinTypeAll 1.3.6.1.4.1.4874.2.2.43.1.1.12.1.20
This object indicates if some other multicast protocol is also interested in receiving data for this entry as a result of its interest in receiving all data. This will be particularly true for dense mode protocols which would want all data (<*, *>) from PIM sparse mode protocol.
Status: current Access: read-only
OBJECT-TYPE    
  TruthValue  

usdPimMRouteOtherProtoOifJoinTypeG 1.3.6.1.4.1.4874.2.2.43.1.1.12.1.21
This object indicates if some other multicast protocol is also interested in receiving data for this entry as a result of its interest in receiving data for a given group. This will be particularly true for IGMP which would want data for a given group (<*, G>) from PIM protocol.
Status: current Access: read-only
OBJECT-TYPE    
  TruthValue  

usdPimMRouteOtherProtoOifJoinTypeSG 1.3.6.1.4.1.4874.2.2.43.1.1.12.1.22
This object indicates if some other multicast protocol is also interested in receiving data for this entry as a result of its interest in receiving data for a given . This will be particularly true for IGMPv3 which would want data for a given ) from PIM sparse-mode protocol.
Status: current Access: read-only
OBJECT-TYPE    
  TruthValue  

usdPimMRoutePimType 1.3.6.1.4.1.4874.2.2.43.1.1.12.1.23
This object indicates if the owner of this entry is Sparse mode or Dense mode PIM. Owner is usually determined by the protocol running on the incoming interface of the entry. In case sparse-dense mode PIM is running on the incoming interface, sparse-mode is the owner if RP for the group is known, else dense mode is the owner.
Status: current Access: read-only
OBJECT-TYPE    
  UsdPimType  

usdPimMRouteNextHopTable 1.3.6.1.4.1.4874.2.2.43.1.1.13
The (conceptual) table listing PIM multicast routing information describing its <*, *, RP>/ <*, G>/ outgoing interfaces.
Status: current Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    UsdPimMRouteNextHopEntry

usdPimMRouteNextHopEntry 1.3.6.1.4.1.4874.2.2.43.1.1.13.1
An entry (conceptual row) in the usdPimMRouteNextHopTable.
Status: current Access: not-accessible
OBJECT-TYPE    
  UsdPimMRouteNextHopEntry  

usdPimMRouteNextHopGroupAddr 1.3.6.1.4.1.4874.2.2.43.1.1.13.1.2
The group address. Specified as 224.0.0.0 for <*, *, RP> entries.
Status: current Access: not-accessible
OBJECT-TYPE    
  IpAddress  

usdPimMRouteNextHopSrcAddr 1.3.6.1.4.1.4874.2.2.43.1.1.13.1.3
The source address. Specified as 0.0.0.0 for <*, *, RP> and <*, G> entries.
Status: current Access: not-accessible
OBJECT-TYPE    
  IpAddress  

usdPimMRouteNextHopSrcMask 1.3.6.1.4.1.4874.2.2.43.1.1.13.1.4
The source address mask. Specified as 255.255.255.255 for entries and 0.0.0.0 for <*, *, RP> and <*, G> entries.
Status: current Access: not-accessible
OBJECT-TYPE    
  IpAddress  

usdPimMRouteNextHopRPAddr 1.3.6.1.4.1.4874.2.2.43.1.1.13.1.5
The RP address used for <*, *, RP>. Specified as 0.0.0.0 for and <*, G> entries.
Status: current Access: not-accessible
OBJECT-TYPE    
  IpAddress  

usdPimMRouteNextHopIfId 1.3.6.1.4.1.4874.2.2.43.1.1.13.1.6
The interface index of the outgoing interface (next hop). Specified as 0 for register outgoing interface. Register outgoing interfaces are created by DR on the source subnet to send PIM register encapsulated data (as unicast) to RP. It is also used by PIM boundary routers (PMBRs) to register data to RP.
Status: current Access: not-accessible
OBJECT-TYPE    
  InterfaceIndex  

usdPimMRouteNextHopAddress 1.3.6.1.4.1.4874.2.2.43.1.1.13.1.7
This object takes following different values based on the type of next hop. It should be set to the address of RP in case the next hop interface is register interface i.e. usdPimMRouteNextHopIfId object is set to 0. It should be set to the address of neighbor in case the interface is an NBMA interface. In all other cases it should be set to the group address itself.
Status: current Access: not-accessible
OBJECT-TYPE    
  IpAddress  

usdPimMRouteNextHopPruneReason 1.3.6.1.4.1.4874.2.2.43.1.1.13.1.8
This object indicates why the downstream interface was pruned, whether in response to a PIM prune message or due to PIM Assert processing.
Status: current Access: read-only
OBJECT-TYPE    
  INTEGER other(1), prune(2), assert(3)  

usdPimMRouteNextHopJoinTypeSSRP 1.3.6.1.4.1.4874.2.2.43.1.1.13.1.9
This object indicates whether or not the interface was added as a result of receiving <*, *, RP> join in case of <*, *, RP> entry OR inherited as outgoing interface from corresponding <*, *, RP> entry in case of <*, G> entry.
Status: current Access: read-only
OBJECT-TYPE    
  TruthValue  

usdPimMRouteNextHopJoinTypeG 1.3.6.1.4.1.4874.2.2.43.1.1.13.1.10
This object indicates whether or not the interface was added as a result of receiving <*, G> join in case of <*, G> entry OR inherited as outgoing interface from corresponding <*, G> entry in case of entry.
Status: current Access: read-only
OBJECT-TYPE    
  TruthValue  

usdPimMRouteNextHopJoinTypeSG 1.3.6.1.4.1.4874.2.2.43.1.1.13.1.11
This object indicates whether or not the interface was added as a result of receiving join in case of entry.
Status: current Access: read-only
OBJECT-TYPE    
  TruthValue  

usdPimMRouteNextHopHasLGM 1.3.6.1.4.1.4874.2.2.43.1.1.13.1.12
This object indicates whether or not the interface has local group membership (as indicated by IGMP) in case of <*, G> and entries.
Status: current Access: read-only
OBJECT-TYPE    
  TruthValue  

usdPimMRouteNextHopHasOifAW 1.3.6.1.4.1.4874.2.2.43.1.1.13.1.13
This object indicates whether or not this interface is the winner of assert for corresponding <*, G>/ entry.
Status: current Access: read-only
OBJECT-TYPE    
  TruthValue  

usdPimMRouteNextHopHasOifSendAssert 1.3.6.1.4.1.4874.2.2.43.1.1.13.1.14
This object indicates whether or not this interface is going to send an assert at the end of assert suppression interval. Assert suppression is used to prevent a flood of assert to be generated in response to data or other asserts.
Status: current Access: read-only
OBJECT-TYPE    
  TruthValue  

usdPimMRouteNextHopHasOifRegister 1.3.6.1.4.1.4874.2.2.43.1.1.13.1.15
This object indicates whether or not this next hop is a register outgoing interface.
Status: current Access: read-only
OBJECT-TYPE    
  TruthValue  

usdPimMRouteNextHopHasOifBorderBit 1.3.6.1.4.1.4874.2.2.43.1.1.13.1.16
This object is used to describe a register outgoing interface. It indicates whether or not the border bit is set in the register packet when the packet is sent over the register interface. For all other (non-register) interfaces its set to false.
Status: current Access: read-only
OBJECT-TYPE    
  TruthValue  

usdPimMRouteNextHopHasOifNullEncapsBit 1.3.6.1.4.1.4874.2.2.43.1.1.13.1.17
This object is used to describe a register outgoing interface. It indicates whether or not the NULL encapsulation bit is set (periodically) in the register packet when the packet is sent over the register interface. For all other (non-register) interfaces its set to false.
Status: current Access: read-only
OBJECT-TYPE    
  TruthValue  

usdPimMRouteNextHopJoinEndTimer 1.3.6.1.4.1.4874.2.2.43.1.1.13.1.18
This object indicates the time (in seconds) left when the join timer expires for the outgoing interface. Join timer for an outgoing interface of entry indicates when the join expires, for a <*, G> entry indicates when the <*, G> join expires and for a <*, *, RP> entry indicates when the <*, *, RP> join expires. Inherited joins (like inheriting from <*, G> AND <*, G> inheriting from <*, *, RP>) expire when the corresponding parent join expires.
Status: current Access: read-only
OBJECT-TYPE    
  TimeTicks  

usdPimMRouteNextHopAssertEndTimer 1.3.6.1.4.1.4874.2.2.43.1.1.13.1.19
This object indicates the time (in seconds) left when the assert timer expires on this outgoing inteface.
Status: current Access: read-only
OBJECT-TYPE    
  TimeTicks  

usdPimMRouteNextHopNextAssertTimer 1.3.6.1.4.1.4874.2.2.43.1.1.13.1.20
This object indicates the duration (in seconds) left for which sending an assert has been suppressed on this outgoing interface.
Status: current Access: read-only
OBJECT-TYPE    
  TimeTicks  

usdPimMRouteNextHopAssertSrcAddress 1.3.6.1.4.1.4874.2.2.43.1.1.13.1.21
This object indicates the source address which will be used in the assert packet to send an assert out for the entry on this outgoing interface. For entries it is the address of the source S itself. For <*, G> entries it is the address of the source whose data was forwarded using this <*, G> and caused the assert situation to happen.
Status: current Access: read-only
OBJECT-TYPE    
  IpAddress  

usdPimMRouteNextHopRegisterSuppressionTimer 1.3.6.1.4.1.4874.2.2.43.1.1.13.1.22
This object is used for register outgoing interfaces. It indicates the duration (in seconds) left for which sending a register packet has been suppressed on the register outgoing interface as a result of receiving register-stop from the RP.
Status: current Access: read-only
OBJECT-TYPE    
  TimeTicks  

usdPimMRouteNextHopPimType 1.3.6.1.4.1.4874.2.2.43.1.1.13.1.23
This object indicates whether the outgoing interface was contributed by sparse-mode or dense-mode PIM.
Status: current Access: read-only
OBJECT-TYPE    
  UsdPimType  

usdPimMRouteNextHopPruneTimeLeft 1.3.6.1.4.1.4874.2.2.43.1.1.13.1.24
This object indicates the time (in seconds) left when the prune timer expires on an outgoing inteface. Its used for pruned outgoing interfaces contributed by dense-mode PIM.
Status: current Access: read-only
OBJECT-TYPE    
  TimeTicks  

usdPimMRouteNextHopsendingIpAddress 1.3.6.1.4.1.4874.2.2.43.1.1.13.1.25
This object describes the source IP address used by this interface to send PIM packets out on this outgoing interface.
Status: current Access: read-only
OBJECT-TYPE    
  IpAddress  

usdPimRPSetTable 1.3.6.1.4.1.4874.2.2.43.1.1.14
The (conceptual) table listing enterprise specific information on a subset of the rows of the pimRPSetTable defined in the standard PIM MIB.
Status: current Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    UsdPimRPSetEntry

usdPimRPSetEntry 1.3.6.1.4.1.4874.2.2.43.1.1.14.1
An entry (conceptual row) in the usdPimRPSetTable.
Status: current Access: not-accessible
OBJECT-TYPE    
  UsdPimRPSetEntry  

usdPimRPSetPriority 1.3.6.1.4.1.4874.2.2.43.1.1.14.1.1
This object describes the priority of the RP for this group-to-RP mapping.
Status: current Access: read-only
OBJECT-TYPE    
  Integer32 1..FFFF  

usdPimRPSetTypeInfo 1.3.6.1.4.1.4874.2.2.43.1.1.14.1.2
This object describes the mechanism by which this group to RP mapping has been learnt, i.e. whether its statically configured, AutoRP learnt or BSR learnt. It also indicates whether the mapping is positive or negative. Negative mappings force the groups in that range to fall into dense-mode category if sparse-dense mode is configured or no RP if its purely sparse mode configuration.
Status: current Access: read-only
OBJECT-TYPE    
  INTEGER pimRPTypeInvalid(0), pimRPTypeStatic(1), pimRPTypeStaticOverride(2), pimRPTypeAutoRP(3), pimRPTypeBSR(4), pimRPTypeStaticNegative(5), pimRPTypeStaticOverrideNegative(6), pimRPTypeAutoRPNegative(7), pimRPTypeBSRNegative(8)  

usdPimRPSetAccessListName 1.3.6.1.4.1.4874.2.2.43.1.1.14.1.3
This object lists the name of the access list from which this group-to-RP mapping was picked up in case of statically configured RPs.
Status: current Access: read-only
OBJECT-TYPE    
  OCTET STRING Size(0..32)  

usdPimStaticRPConfTable 1.3.6.1.4.1.4874.2.2.43.1.1.15
The (conceptual) table listing statically configured PIM RPs.
Status: current Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    UsdPimStaticRPConfEntry

usdPimStaticRPConfEntry 1.3.6.1.4.1.4874.2.2.43.1.1.15.1
An entry (conceptual row) in the usdPimStaticRPConfTable.
Status: current Access: not-accessible
OBJECT-TYPE    
  UsdPimStaticRPConfEntry  

usdPimStaticRPConfComponentIndex 1.3.6.1.4.1.4874.2.2.43.1.1.15.1.1
A number uniquely identifying the component. Each protocol instance connected to a separate domain should have a different index value.
Status: current Access: not-accessible
OBJECT-TYPE    
  Integer32 0..2147483647  

usdPimStaticRPConfRPAddr 1.3.6.1.4.1.4874.2.2.43.1.1.15.1.2
Ip address of the RP which for the group-to-RP mapping being configured.
Status: current Access: not-accessible
OBJECT-TYPE    
  IpAddress  

usdPimStaticRPConfAccessListName 1.3.6.1.4.1.4874.2.2.43.1.1.15.1.3
Name of the access list from which group-ranges are picked up for this group-ro-RP mapping. Every deny component in the list is added as negative group-ro-RP mapping.
Status: current Access: not-accessible
OBJECT-TYPE    
  OCTET STRING Size(0..32)  

usdPimStaticRPConfRowStatus 1.3.6.1.4.1.4874.2.2.43.1.1.15.1.4
The status of this row, by which new entries may be created, or old entries deleted from this table.
Status: current Access: read-create
OBJECT-TYPE    
  RowStatus  

usdPimStaticRPConfOverride 1.3.6.1.4.1.4874.2.2.43.1.1.15.1.5
The object indicates whether or not this statically configured group-to-RP mapping should override the group-to-RP mapping learnt via AutoRP for the component group-ranges in the access list. By default AutoRP learnt group-to-RP mappings are preferred over statically configured ones. While setting the rowStatus to create a static RP, this field should be assigned to true if the override property is desired.
Status: current Access: read-create
OBJECT-TYPE    
  TruthValue  

usdPimAutoRPConfTable 1.3.6.1.4.1.4874.2.2.43.1.1.16
The (conceptual) table allowing AutoRP configuration of candidate RPs (advertisement agents).
Status: current Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    UsdPimAutoRPConfEntry

usdPimAutoRPConfEntry 1.3.6.1.4.1.4874.2.2.43.1.1.16.1
An entry (conceptual row) in the usdPimAutoRPConfTable.
Status: current Access: not-accessible
OBJECT-TYPE    
  UsdPimAutoRPConfEntry  

usdPimAutoRPConfComponentIndex 1.3.6.1.4.1.4874.2.2.43.1.1.16.1.1
A number uniquely identifying the component. Each protocol instance connected to a separate domain should have a different index value.
Status: current Access: not-accessible
OBJECT-TYPE    
  Integer32 0..2147483647  

usdPimAutoRPConfCandRPAddr 1.3.6.1.4.1.4874.2.2.43.1.1.16.1.2
The IP address of the candidate RP for this advertising agent configuration.
Status: current Access: not-accessible
OBJECT-TYPE    
  IpAddress  

usdPimAutoRPConfGroupAccessListName 1.3.6.1.4.1.4874.2.2.43.1.1.16.1.3
The access list name from which group ranges are picked up for advertising agent configuration.
Status: current Access: not-accessible
OBJECT-TYPE    
  OCTET STRING Size(0..32)  

usdPimAutoRPConfRowStatus 1.3.6.1.4.1.4874.2.2.43.1.1.16.1.4
The status of this row, by which new entries may be created, or old entries deleted from this table.
Status: current Access: read-create
OBJECT-TYPE    
  RowStatus  

usdPimAutoRPConfTTL 1.3.6.1.4.1.4874.2.2.43.1.1.16.1.5
The time-to-live value used while sending AutoRP advertisement out for this group-to-RP mappings created as a result of this configuration. This should be set along with usdPimAutoRPConfRowStatus while creating an AutoRP advertising agent to denote the TTL value to be used.
Status: current Access: read-create
OBJECT-TYPE    
  Integer32 1..FFFF  

usdPimAutoRPConfAncmntIntvl 1.3.6.1.4.1.4874.2.2.43.1.1.16.1.6
The time interval at which AutoRP advertisements are sent out for the group-to-RP mappings created as a result of this configuration. This should be set along with usdPimAutoRPConfRowStatus while creating an AutoRP advertising agent to denote the announcement interval to be used.
Status: current Access: read-create
OBJECT-TYPE    
  TimeTicks  

usdPimAutoRPConfifId 1.3.6.1.4.1.4874.2.2.43.1.1.16.1.7
The interface index of the interface for the candidate RP if an interface with that address exists else it is set to 0.
Status: current Access: read-only
OBJECT-TYPE    
  InterfaceIndex  

usdPimAutoRPCandTable 1.3.6.1.4.1.4874.2.2.43.1.1.17
The (conceptual) table listing AutoRP candidate RPS (advertising agents).
Status: current Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    UsdPimAutoRPCandEntry

usdPimAutoRPCandEntry 1.3.6.1.4.1.4874.2.2.43.1.1.17.1
An entry (conceptual row) in the usdPimAutoRPCandTable.
Status: current Access: not-accessible
OBJECT-TYPE    
  UsdPimAutoRPCandEntry  

usdPimAutoRPCandComponentIndex 1.3.6.1.4.1.4874.2.2.43.1.1.17.1.1
A number uniquely identifying the component. Each protocol instance connected to a separate domain should have a different index value.
Status: current Access: not-accessible
OBJECT-TYPE    
  Integer32 0..2147483647  

usdPimAutoRPCandRPAddr 1.3.6.1.4.1.4874.2.2.43.1.1.17.1.2
The IP address of the candidate RP for this group-to-RP mapping.
Status: current Access: not-accessible
OBJECT-TYPE    
  IpAddress  

usdPimAutoRPCandGroupAddr 1.3.6.1.4.1.4874.2.2.43.1.1.17.1.3
The group address of the candidate RP for this group-to-RP mapping.
Status: current Access: not-accessible
OBJECT-TYPE    
  IpAddress  

usdPimAutoRPCandGroupMask 1.3.6.1.4.1.4874.2.2.43.1.1.17.1.4
The group mask of the candidate RP for this group-to-RP mapping.
Status: current Access: not-accessible
OBJECT-TYPE    
  IpAddress  

usdPimAutoRPCandRowStatus 1.3.6.1.4.1.4874.2.2.43.1.1.17.1.5
The current status of this row.
Status: current Access: read-only
OBJECT-TYPE    
  RowStatus  

usdPimAutoRPCandAccessListName 1.3.6.1.4.1.4874.2.2.43.1.1.17.1.6
The name of the group list using which this AutoRP group-to-RP candidate RP mapping was configured.
Status: current Access: read-only
OBJECT-TYPE    
  OCTET STRING Size(0..32)  

usdPimAutoRPCandAutoRPTTL 1.3.6.1.4.1.4874.2.2.43.1.1.17.1.7
The time-to-live value used while sending AutoRP advertisement out for this group-to-RP mapping.
Status: current Access: read-only
OBJECT-TYPE    
  Integer32 1..FFFF  

usdPimAutoRPCandAutoRPAncmntIntvl 1.3.6.1.4.1.4874.2.2.43.1.1.17.1.8
The time interval at which AutoRP advertisements are sent out for this group-to-RP mapping.
Status: current Access: read-only
OBJECT-TYPE    
  TimeTicks  

usdPimAutoRPCandIfId 1.3.6.1.4.1.4874.2.2.43.1.1.17.1.9
The interface index of the interface for this AutoRP group-to-RP candidate RP mapping if an interface for RP address exists else it is set to 0.
Status: current Access: read-only
OBJECT-TYPE    
  InterfaceIndex  

usdPimComponentTable 1.3.6.1.4.1.4874.2.2.43.1.1.18
The (conceptual) table listing each component (domain) in PIM.
Status: current Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    UsdPimComponentEntry

usdPimComponentEntry 1.3.6.1.4.1.4874.2.2.43.1.1.18.1
An entry (conceptual row) in the usdPimComponentTable.
Status: current Access: not-accessible
OBJECT-TYPE    
  UsdPimComponentEntry  

usdPimComponentIndex 1.3.6.1.4.1.4874.2.2.43.1.1.18.1.1
A number uniquely identifying the component. Each protocol instance connected to a separate domain should have a different index value.
Status: current Access: not-accessible
OBJECT-TYPE    
  Integer32 0..2147483647  

usdPimComponentAutoRPMappingAgentRowStatus 1.3.6.1.4.1.4874.2.2.43.1.1.18.1.2
The status of AutoRP mapping agent by which this router can be made an AutoRP mapping agent or removed from being an AutoRP mapping agent in this component.
Status: current Access: read-create
OBJECT-TYPE    
  RowStatus  

usdPimComponentConfiguredAutoRPMappingAgentIfId 1.3.6.1.4.1.4874.2.2.43.1.1.18.1.3
The interface index of the interface which mapping agent should use to send AutoRP mapping messages. If not specified, the interface with highest IP address in this domain is picked up for this purpose.
Status: current Access: read-create
OBJECT-TYPE    
  InterfaceIndex  

usdPimComponentAutoRPMappingAgentInterval 1.3.6.1.4.1.4874.2.2.43.1.1.18.1.4
The time interval at which AutoRP mapping messages are sent out in this component. The default value is 60 seconds.
Status: current Access: read-create
OBJECT-TYPE    
  TimeTicks  

usdPimComponentAutoRPMappingTTL 1.3.6.1.4.1.4874.2.2.43.1.1.18.1.5
The time-to-live value used while sending AutoRP mapping messages out in this component.
Status: current Access: read-create
OBJECT-TYPE    
  Integer32 1..FFFF  

usdPimComponentAutoRPMappingAgentIntfAddr 1.3.6.1.4.1.4874.2.2.43.1.1.18.1.6
The IP address of the interface which mapping agent is using to send AutoRP mapping messages.
Status: current Access: read-only
OBJECT-TYPE    
  IpAddress  

usdPimComponentAutoRPMappingAgentWinnerAddr 1.3.6.1.4.1.4874.2.2.43.1.1.18.1.7
The IP address of the winner AutoRP mapping agent. There can be multiple mapping agents configured in a given PIM domain(component). The mapping agent with highest IP address is chosen as the winner and it continues to send AutoRP mapping messages. If the router itself is the winner, then this is set to 0.0.0.0.
Status: current Access: read-only
OBJECT-TYPE    
  IpAddress  

usdPimComponentAutoRPMappingAgentWinnerLastHeard 1.3.6.1.4.1.4874.2.2.43.1.1.18.1.8
The time (in seconds) that has past since an AutoRP mapping message was receieved from the winner AutoRP mapping agent. If the router itself is the winner, then this is set to 0.
Status: current Access: read-only
OBJECT-TYPE    
  TimeTicks  

usdPimUnicastRouteTable 1.3.6.1.4.1.4874.2.2.43.1.1.19
The (conceptual) table listing all the unicast routes currently in use by PIM for diong RPF checking.
Status: current Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    UsdPimUnicastRouteEntry

usdPimUnicastRouteEntry 1.3.6.1.4.1.4874.2.2.43.1.1.19.1
An entry (conceptual row) in the usdPimUnicastRouteTable.
Status: current Access: not-accessible
OBJECT-TYPE    
  UsdPimUnicastRouteEntry  

usdPimUnicastRouteEntryAddr 1.3.6.1.4.1.4874.2.2.43.1.1.19.1.1
The address of route in use.
Status: current Access: not-accessible
OBJECT-TYPE    
  IpAddress  

usdPimUnicastRouteEntryMask 1.3.6.1.4.1.4874.2.2.43.1.1.19.1.2
The mask of route in use.
Status: current Access: not-accessible
OBJECT-TYPE    
  IpAddress  

usdPimUnicastRouteEntryRpfNbr 1.3.6.1.4.1.4874.2.2.43.1.1.19.1.3
The RPF neighbor (next-hop) to reach the route of this entry. It is set to 0.0.0.0 for directly connected routes.
Status: current Access: read-only
OBJECT-TYPE    
  IpAddress  

usdPimUnicastRouteEntryIifId 1.3.6.1.4.1.4874.2.2.43.1.1.19.1.4
The interface index (next-hop) to reach the route of this entry.
Status: current Access: read-only
OBJECT-TYPE    
  InterfaceIndex  

usdPimUnicastRouteEntryIifAddr 1.3.6.1.4.1.4874.2.2.43.1.1.19.1.5
The interface address (next-hop) to reach the route of this entry.
Status: current Access: read-only
OBJECT-TYPE    
  IpAddress  

usdPimUnicastRouteEntryPref 1.3.6.1.4.1.4874.2.2.43.1.1.19.1.6
The preference of the route of this entry.
Status: current Access: read-only
OBJECT-TYPE    
  Integer32  

usdPimUnicastRouteEntryMetric 1.3.6.1.4.1.4874.2.2.43.1.1.19.1.7
The metric of the route of this entry.
Status: current Access: read-only
OBJECT-TYPE    
  Integer32  

usdPimUnicastRouteEntryPimType 1.3.6.1.4.1.4874.2.2.43.1.1.19.1.8
This object indicates whether the route specified in this entry is being used by sparse-mode and/or dense-mode PIM.
Status: current Access: read-only
OBJECT-TYPE    
  UsdPimType  

usdPimSPTThresholdTable 1.3.6.1.4.1.4874.2.2.43.1.1.20
The (conceptual) table listing threshold values set for switching from shared tree to shortest path tree and vice versa for data forwarded by PIM sparse-mode.
Status: current Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    UsdPimSPTThresholdEntry

usdPimSPTThresholdEntry 1.3.6.1.4.1.4874.2.2.43.1.1.20.1
An entry (conceptual row) in the usdPimSPTThresholdTable.
Status: current Access: not-accessible
OBJECT-TYPE    
  UsdPimSPTThresholdEntry  

usdPimSPTThresholdAccessListName 1.3.6.1.4.1.4874.2.2.43.1.1.20.1.1
The name of the access list from which group ranges are picked up for setting SPT threshold in this entry.
Status: current Access: not-accessible
OBJECT-TYPE    
  OCTET STRING Size(0..32)  

usdPimSPTThresHoldRowStatus 1.3.6.1.4.1.4874.2.2.43.1.1.20.1.2
The status of this row, by which new entries may be created, or old entries deleted from this table.
Status: current Access: read-write
OBJECT-TYPE    
  RowStatus  

usdPimSPTThresholdKbps 1.3.6.1.4.1.4874.2.2.43.1.1.20.1.3
The value of SPT threshold in kilobits per second. Default value is 0.
Status: current Access: read-write
OBJECT-TYPE    
  Integer32  

usdPimConformance 1.3.6.1.4.1.4874.2.2.43.2
OBJECT IDENTIFIER    

usdPimCompliances 1.3.6.1.4.1.4874.2.2.43.2.1
OBJECT IDENTIFIER    

usdPimGroups 1.3.6.1.4.1.4874.2.2.43.2.2
OBJECT IDENTIFIER    

usdPimCompliance 1.3.6.1.4.1.4874.2.2.43.2.1.1
The compliance statement for entities which implement the Unisphere PIM MIB.
Status: current Access: read-write
MODULE-COMPLIANCE    

usdPimGeneralGroup 1.3.6.1.4.1.4874.2.2.43.2.2.1
A collection of objects for managing general PIM capabilities in a Unisphere product.
Status: current Access: read-write
OBJECT-GROUP    

usdPimInterfaceGroup 1.3.6.1.4.1.4874.2.2.43.2.2.2
A collection of objects for managing PIM interface capabilities in a Unisphere product.
Status: current Access: read-write
OBJECT-GROUP    

usdPimMRouteConfGroup 1.3.6.1.4.1.4874.2.2.43.2.2.3
A collection of objects for managing PIM multicast route capabilities in a Unisphere product.
Status: current Access: read-write
OBJECT-GROUP    

usdPimMRouteNextHopGroup 1.3.6.1.4.1.4874.2.2.43.2.2.4
A collection of objects for managing PIM multicast route next hop capabilities in a Unisphere product.
Status: current Access: read-write
OBJECT-GROUP    

usdPimRPSetGroup 1.3.6.1.4.1.4874.2.2.43.2.2.5
A collection of objects for managing PIM RP-Set capabilities in a Unisphere product.
Status: current Access: read-write
OBJECT-GROUP    

usdPimStaticRPConfGroup 1.3.6.1.4.1.4874.2.2.43.2.2.6
A collection of objects for managing statically configured PIM RPs capabilities in a Unisphere product.
Status: current Access: read-write
OBJECT-GROUP    

usdPimAutoRPConfGroup 1.3.6.1.4.1.4874.2.2.43.2.2.7
A collection of objects for managing PIM AutoRP candidate advertisment agent RP capabilities in a Unisphere product.
Status: current Access: read-write
OBJECT-GROUP    

usdPimAutoRPCandGroup 1.3.6.1.4.1.4874.2.2.43.2.2.8
A collection of objects for managing PIM AutoRP candidate advertising agent RP capabilities in a Unisphere product.
Status: current Access: read-write
OBJECT-GROUP    

usdPimComponentGroup 1.3.6.1.4.1.4874.2.2.43.2.2.9
A collection of objects for managing PIM component (domain) capabilities in a Unisphere product.
Status: current Access: read-write
OBJECT-GROUP    

usdPimUnicastRouteGroup 1.3.6.1.4.1.4874.2.2.43.2.2.10
A collection of objects for managing PIM unicast route capabilities in a Unisphere product.
Status: current Access: read-write
OBJECT-GROUP    

usdPimSPTThresholdGroup 1.3.6.1.4.1.4874.2.2.43.2.2.11
A collection of objects for managing PIM shortest path tree threshold capabilities in a Unisphere product.
Status: current Access: read-write
OBJECT-GROUP