Unisphere-Data-FRACTIONAL-T1-MIB
File:
Unisphere-Data-FRACTIONAL-T1-MIB.mib (11107 bytes)
Imported modules
Imported symbols
Defined Types
UsdFt1IfEntry |
|
SEQUENCE |
|
|
|
|
usdFt1IfIndex |
InterfaceIndex |
|
|
usdFt1IfRowStatus |
RowStatus |
|
|
usdFt1IfLowerIfIndex |
InterfaceIndexOrZero |
|
|
usdFt1IfTimeSlotMap |
UsdTimeSlotMap |
|
|
usdFt1IfTimeSlotRate |
INTEGER |
|
|
usdFt1IfDataPolarity |
INTEGER |
|
|
usdFt1IfLoopbackConfig |
INTEGER |
|
Defined Values
usdFt1MIB |
1.3.6.1.4.1.4874.2.2.6 |
The Fractional T1 MIB for the Unisphere Networks Inc. enterprise. |
MODULE-IDENTITY |
|
|
|
usdFt1NextIfIndex |
1.3.6.1.4.1.4874.2.2.6.1.1 |
Coordinate ifIndex value allocation for entries
in usdFt1IfTable.
A GET of this object returns the next available ifIndex
value to be used to create an entry in the associated
interface table; or zero, if no valid ifIndex value is
available. This object also returns a value of zero when
it is the lexicographic successor of a varbind presented
in an SNMP GETNEXT or GETBULK request, for which circumstance
it is assumed that ifIndex allocation is unintended.
Successive GETs will typically return different
values, thus avoiding collisions among cooperating
management clients seeking to create table entries
simultaneously.
|
Status: current |
Access: read-only |
OBJECT-TYPE |
|
|
|
|
UsdNextIfIndex |
|
|
usdFt1IfTable |
1.3.6.1.4.1.4874.2.2.6.1.2 |
This table contains entries for FT1 interfaces present in the system. |
Status: current |
Access: not-accessible |
OBJECT-TYPE |
|
|
|
|
SEQUENCE OF |
|
|
|
|
UsdFt1IfEntry |
|
usdFt1IfEntry |
1.3.6.1.4.1.4874.2.2.6.1.2.1 |
Each entry describes the characteristics of an FT1 interface.
Creating/deleting entries in this table causes corresponding
entries for be created /deleted in ifTable/ifXTable/usdIfTable. |
Status: current |
Access: not-accessible |
OBJECT-TYPE |
|
|
|
|
UsdFt1IfEntry |
|
|
usdFt1IfIndex |
1.3.6.1.4.1.4874.2.2.6.1.2.1.1 |
The ifIndex of the FT1 interface. When
creating entries in this table, suitable values
for this object are determined by reading
usdFt1NextIfIndex. |
Status: current |
Access: not-accessible |
OBJECT-TYPE |
|
|
|
|
InterfaceIndex |
|
|
usdFt1IfRowStatus |
1.3.6.1.4.1.4874.2.2.6.1.2.1.2 |
Controls creation/deletion of entries in this table
according to the RowStatus textual convention,
constrained to support the following values only:
createAndGo
destroy
To create an entry in this table, the following
entry objects MUST be explicitly configured:
usdFt1IfRowStatus
usdFt1IfLowerIfIndex
usdFt1IfTimeSlotMap
In addition, when creating an entry the following
conditions must hold:
A value for usdFt1IfIndex must have been determined
previously, by reading usdFt1NextIfIndex.
The DS1 interface identified by usdFt1IfLowerIfIndex
must exist.
The DS0s specified in usdFt1IfTimeSlotMap must be
available (unallocated) on the DS1 interface
identified by usdFt1IfLowerIfIndex.
A corresponding entry in ifTable/ifXTable/usdIfTable is
created/destroyed as a result of creating/destroying an entry
in this table.
|
Status: current |
Access: read-create |
OBJECT-TYPE |
|
|
|
|
RowStatus |
|
|
usdFt1IfLowerIfIndex |
1.3.6.1.4.1.4874.2.2.6.1.2.1.3 |
The ifIndex of a DS1 interface over which this FT1 interface
is to be layered. A value of zero indicates no layering.
An implementation may choose to require that a nonzero value
be configured at entry creation. |
Status: current |
Access: read-create |
OBJECT-TYPE |
|
|
|
|
InterfaceIndexOrZero |
|
|
usdFt1IfTimeSlotMap |
1.3.6.1.4.1.4874.2.2.6.1.2.1.4 |
A bitmap representing the DS0s on the underlying DS1 interface
that have been allocated to this FT1 interface. |
Status: current |
Access: read-create |
OBJECT-TYPE |
|
|
|
|
UsdTimeSlotMap |
|
|
usdFt1IfTimeSlotRate |
1.3.6.1.4.1.4874.2.2.6.1.2.1.5 |
Data rate per time slot allocated to this FT1 interface. |
Status: current |
Access: read-create |
OBJECT-TYPE |
|
|
|
|
INTEGER |
nx56kbps(0), nx64kbps(1) |
|
usdFt1IfDataPolarity |
1.3.6.1.4.1.4874.2.2.6.1.2.1.6 |
Polarity of data transmitted on this FT1 interface. Inverted data is
used for certain line coding configurations to ensure sufficient
one's density for timing recovery by the remote end. |
Status: obsolete |
Access: read-create |
OBJECT-TYPE |
|
|
|
|
INTEGER |
normal(0), inverted(1) |
|
usdFt1IfLoopbackConfig |
1.3.6.1.4.1.4874.2.2.6.1.2.1.7 |
Selects loopback configuration. loop(1) causes received data to be
looped back out the transmitter. |
Status: current |
Access: read-create |
OBJECT-TYPE |
|
|
|
|
INTEGER |
noLoop(0), loop(1) |
|
usdFt1Compliance |
1.3.6.1.4.1.4874.2.2.6.4.1.1 |
The compliance statement for entities that implement the Unisphere FT1
MIB. |
Status: obsolete |
Access: read-create |
MODULE-COMPLIANCE |
|
|
|
usdFt1Compliance2 |
1.3.6.1.4.1.4874.2.2.6.4.1.2 |
The compliance statement for entities that implement the Unisphere FT1
MIB. |
Status: current |
Access: read-create |
MODULE-COMPLIANCE |
|
|
|
usdFt1Group |
1.3.6.1.4.1.4874.2.2.6.4.2.1 |
A collection of objects providing management of FT1 interfaces
in a Unisphere product. |
Status: obsolete |
Access: read-create |
OBJECT-GROUP |
|
|
|
usdFt1Group2 |
1.3.6.1.4.1.4874.2.2.6.4.2.2 |
A collection of objects providing management of FT1 interfaces
in a Unisphere product. |
Status: current |
Access: read-create |
OBJECT-GROUP |
|
|
|