TRANZEO-ENROUTE-MUNIWIFI-MIB

File: TRANZEO-ENROUTE-MUNIWIFI-MIB.mib (189200 bytes)

Imported modules

SNMPv2-SMI

RFC-1215

Imported symbols

MODULE-IDENTITY	OBJECT-TYPE	enterprises
Integer32	TRAP-TYPE

Defined Values

enRoute		1.3.6.1.4.1.24350
The Tranzeo EnRoute platform MIB.
MODULE-IDENTITY

version		1.3.6.1.4.1.24350.1
OBJECT IDENTIFIER

versionDriver80211		1.3.6.1.4.1.24350.1.1
80211 driver release version
Status: current	Access: read-only
OBJECT-TYPE
	OCTET STRING

versionFirmware		1.3.6.1.4.1.24350.1.2
firmware release version
Status: current	Access: read-only
OBJECT-TYPE
	OCTET STRING

versionLoaded-profile		1.3.6.1.4.1.24350.1.3
last mcm cfg-load or cfg-save profile
Status: current	Access: read-only
OBJECT-TYPE
	OCTET STRING

versionMcm		1.3.6.1.4.1.24350.1.4
mcm version
Status: current	Access: read-only
OBJECT-TYPE
	OCTET STRING

versionPatches		1.3.6.1.4.1.24350.1.5
applied patches
Status: current	Access: read-only
OBJECT-TYPE
	OCTET STRING

versionQos		1.3.6.1.4.1.24350.1.6
QoS version
Status: current	Access: read-only
OBJECT-TYPE
	OCTET STRING

versionRelease		1.3.6.1.4.1.24350.1.7
software release version
Status: current	Access: read-only
OBJECT-TYPE
	OCTET STRING

sys		1.3.6.1.4.1.24350.2
OBJECT IDENTIFIER

sysApply		1.3.6.1.4.1.24350.2.1
OBJECT IDENTIFIER

sysApplyEffect		1.3.6.1.4.1.24350.2.1.1
approximate severity of applying outstanding changes
Status: current	Access: read-only
OBJECT-TYPE
	OCTET STRING

sysApplyTime		1.3.6.1.4.1.24350.2.1.2
time in seconds to apply outstanding changes
Status: current	Access: read-only
OBJECT-TYPE
	INTEGER

sysDev		1.3.6.1.4.1.24350.2.2
OBJECT IDENTIFIER

sysDevBattery		1.3.6.1.4.1.24350.2.2.1
OBJECT IDENTIFIER

sysDevBatteryEnable		1.3.6.1.4.1.24350.2.2.1.1
enable battery
Status: current	Access: read-write
OBJECT-TYPE
	OCTET STRING

sysDevBatteryInstalled		1.3.6.1.4.1.24350.2.2.1.2
battery hardware could be installed
Status: current	Access: read-only
OBJECT-TYPE
	OCTET STRING

sysDevLed		1.3.6.1.4.1.24350.2.2.2
OBJECT IDENTIFIER

sysDevLedEnable		1.3.6.1.4.1.24350.2.2.2.1
enable led display
Status: current	Access: read-write
OBJECT-TYPE
	OCTET STRING

sysDevPoe		1.3.6.1.4.1.24350.2.2.3
OBJECT IDENTIFIER

sysDevPoeEnable		1.3.6.1.4.1.24350.2.2.3.1
supply power over ethernet
Status: current	Access: read-write
OBJECT-TYPE
	OCTET STRING

sysDevPoeInstalled		1.3.6.1.4.1.24350.2.2.3.2
poe hardware is installed
Status: current	Access: read-only
OBJECT-TYPE
	OCTET STRING

sysDevPoeVoltage		1.3.6.1.4.1.24350.2.2.3.3
power over ethernet voltage - 24 or 48
Status: current	Access: read-write
OBJECT-TYPE
	OCTET STRING

sysDevWlan		1.3.6.1.4.1.24350.2.2.4
OBJECT IDENTIFIER

sysDevWlanCountry		1.3.6.1.4.1.24350.2.2.4.1
ansi country code - 124=canada, 840=us, 826=uk
Status: current	Access: read-write
OBJECT-TYPE
	INTEGER

sysDhcp		1.3.6.1.4.1.24350.2.3
OBJECT IDENTIFIER

sysDhcpArgs		1.3.6.1.4.1.24350.2.3.1
dhcp server arguments
Status: current	Access: read-only
OBJECT-TYPE
	OCTET STRING

sysDhcpEnableserver		1.3.6.1.4.1.24350.2.3.2
enable dhcp server if any of the interfaces require it
Status: current	Access: read-write
OBJECT-TYPE
	OCTET STRING

sysDhcpRelay		1.3.6.1.4.1.24350.2.3.3
OBJECT IDENTIFIER

sysDhcpRelayAgent		1.3.6.1.4.1.24350.2.3.3.1
OBJECT IDENTIFIER

sysDhcpRelayAgentBase		1.3.6.1.4.1.24350.2.3.3.1.1
base octet to use for alias VAP IP addresses
Status: current	Access: read-write
OBJECT-TYPE
	OCTET STRING

sysDhcpRelayArgs		1.3.6.1.4.1.24350.2.3.3.2
roamd arguments except for -D and -a
Status: current	Access: read-write
OBJECT-TYPE
	OCTET STRING

sysDhcpRelayArpnumbc		1.3.6.1.4.1.24350.2.3.3.3
number of unsolicited arp broadcasts to establish ips
Status: current	Access: read-write
OBJECT-TYPE
	INTEGER

sysDhcpRelayBindretries		1.3.6.1.4.1.24350.2.3.3.4
number of interface bind attempts
Status: current	Access: read-write
OBJECT-TYPE
	INTEGER

sysDhcpRelayEnable		1.3.6.1.4.1.24350.2.3.3.5
use remote dhcp server instead of local
Status: current	Access: read-write
OBJECT-TYPE
	OCTET STRING

sysDhcpRelayExtrahosts		1.3.6.1.4.1.24350.2.3.3.6
space separated list of extra host ip addresses to consider external
Status: current	Access: read-write
OBJECT-TYPE
	OCTET STRING

sysDhcpRelayGateway		1.3.6.1.4.1.24350.2.3.3.7
base address to use VAP IP addresses globally
Status: current	Access: read-write
OBJECT-TYPE
	OCTET STRING

sysDhcpRelayImr		1.3.6.1.4.1.24350.2.3.3.8
OBJECT IDENTIFIER

sysDhcpRelayImrNumbc		1.3.6.1.4.1.24350.2.3.3.8.1
notification broadcast count
Status: current	Access: read-write
OBJECT-TYPE
	INTEGER

sysDhcpRelayProxy		1.3.6.1.4.1.24350.2.3.3.9
redirect all dhcp traffic to relay on gateway
Status: current	Access: read-write
OBJECT-TYPE
	OCTET STRING

sysDhcpRelayServer		1.3.6.1.4.1.24350.2.3.3.10
numeric ip address of the external DHCP server
Status: current	Access: read-write
OBJECT-TYPE
	OCTET STRING

sysDhcpRelayStalecheckinterval		1.3.6.1.4.1.24350.2.3.3.11
check for stale route (seconds)
Status: current	Access: read-write
OBJECT-TYPE
	INTEGER

sysDhcpRelayStatic		1.3.6.1.4.1.24350.2.3.3.12
OBJECT IDENTIFIER

sysDhcpRelayStaticBegin		1.3.6.1.4.1.24350.2.3.3.12.1
beginning of statif ip range
Status: current	Access: read-write
OBJECT-TYPE
	OCTET STRING

sysDhcpRelayStaticEnable		1.3.6.1.4.1.24350.2.3.3.12.2
allow static allocation range
Status: current	Access: read-write
OBJECT-TYPE
	OCTET STRING

sysDhcpRelayStaticEnd		1.3.6.1.4.1.24350.2.3.3.12.3
end of static ip range
Status: current	Access: read-write
OBJECT-TYPE
	OCTET STRING

sysDhcpRelaySubnet		1.3.6.1.4.1.24350.2.3.3.13
subnet for roamd
Status: current	Access: read-write
OBJECT-TYPE
	OCTET STRING

sysDhcpRelayTunnel		1.3.6.1.4.1.24350.2.3.3.14
OBJECT IDENTIFIER

sysDhcpRelayTunnelEndpoint		1.3.6.1.4.1.24350.2.3.3.14.1
tunnel subnet for roamd
Status: current	Access: read-write
OBJECT-TYPE
	OCTET STRING

sysDhcpRelayTunnelKeepalive		1.3.6.1.4.1.24350.2.3.3.14.2
tunnel keepalive interval in seconds
Status: current	Access: read-write
OBJECT-TYPE
	INTEGER

sysDhcpRelayTunnelTimeoutfactor		1.3.6.1.4.1.24350.2.3.3.14.3
tunnel timeout factor
Status: current	Access: read-write
OBJECT-TYPE
	INTEGER

sysDns		1.3.6.1.4.1.24350.2.4
OBJECT IDENTIFIER

sysDnsServers		1.3.6.1.4.1.24350.2.4.1
space separated DNS server list
Status: current	Access: read-write
OBJECT-TYPE
	OCTET STRING

sysDnsUpdatestyle		1.3.6.1.4.1.24350.2.4.2
dns update style ('ad-hoc', 'interim', 'none' )
Status: current	Access: read-write
OBJECT-TYPE
	OCTET STRING

sysDnsproxy		1.3.6.1.4.1.24350.2.5
OBJECT IDENTIFIER

sysDnsproxyEnable		1.3.6.1.4.1.24350.2.5.1
enable dns proxy
Status: current	Access: read-write
OBJECT-TYPE
	OCTET STRING

sysDnsproxyHosts		1.3.6.1.4.1.24350.2.5.2
=;=; (etc)
Status: current	Access: read-write
OBJECT-TYPE
	OCTET STRING

sysDomain		1.3.6.1.4.1.24350.2.6
domain for this node
Status: current	Access: read-write
OBJECT-TYPE
	OCTET STRING

sysGui		1.3.6.1.4.1.24350.2.7
OBJECT IDENTIFIER

sysGuiUpgrade		1.3.6.1.4.1.24350.2.7.1
OBJECT IDENTIFIER

sysGuiUpgradeForce		1.3.6.1.4.1.24350.2.7.1.1
gui defaults to forcing upgrade
Status: current	Access: read-write
OBJECT-TYPE
	OCTET STRING

sysHostname		1.3.6.1.4.1.24350.2.8
hostname (also set if you change id.node)
Status: current	Access: read-write
OBJECT-TYPE
	OCTET STRING

sysHosts		1.3.6.1.4.1.24350.2.9
OBJECT IDENTIFIER

sysHostsNms		1.3.6.1.4.1.24350.2.9.1
hostname or ip address of the network management station (snmp)
Status: current	Access: read-write
OBJECT-TYPE
	OCTET STRING

sysId		1.3.6.1.4.1.24350.2.10
OBJECT IDENTIFIER

sysIdLanprefix		1.3.6.1.4.1.24350.2.10.1
first octet for non-mesh interfaces
Status: current	Access: read-write
OBJECT-TYPE
	OCTET STRING

sysIdMesh		1.3.6.1.4.1.24350.2.10.2
3rd mesh octet (2nd octet for other interfaces in implicit mode)
Status: current	Access: read-write
OBJECT-TYPE
	OCTET STRING

sysIdMeshprefix		1.3.6.1.4.1.24350.2.10.3
first two octets for mesh
Status: current	Access: read-write
OBJECT-TYPE
	OCTET STRING

sysIdNode		1.3.6.1.4.1.24350.2.10.4
4th mesh octet (3rd octet for other interfaces in implicit mode)
Status: current	Access: read-write
OBJECT-TYPE
	OCTET STRING

sysImplicit		1.3.6.1.4.1.24350.2.11
OBJECT IDENTIFIER

sysImplicitEnable		1.3.6.1.4.1.24350.2.11.1
use implicit addressing scheme - limits ap ranges
Status: current	Access: read-write
OBJECT-TYPE
	OCTET STRING

sysInfo		1.3.6.1.4.1.24350.2.12
OBJECT IDENTIFIER

sysInfoCluster		1.3.6.1.4.1.24350.2.12.1
freeform string which will be displayed on web pages
Status: current	Access: read-write
OBJECT-TYPE
	OCTET STRING

sysL2		1.3.6.1.4.1.24350.2.13
OBJECT IDENTIFIER

sysL2Bridge		1.3.6.1.4.1.24350.2.13.1
OBJECT IDENTIFIER

sysL2BridgeEnable		1.3.6.1.4.1.24350.2.13.1.1
enable level 2 bridge mode
Status: current	Access: read-write
OBJECT-TYPE
	OCTET STRING

sysL2Clientmacfwd		1.3.6.1.4.1.24350.2.13.2
preserve client source mac to gateway and enable gateway proxy_arp
Status: current	Access: read-write
OBJECT-TYPE
	OCTET STRING

sysL2Hideinternal		1.3.6.1.4.1.24350.2.13.3
OBJECT IDENTIFIER

sysL2HideinternalEnable		1.3.6.1.4.1.24350.2.13.3.1
hide internal subnets from proxy arps
Status: current	Access: read-write
OBJECT-TYPE
	OCTET STRING

sysL2HideinternalGateway		1.3.6.1.4.1.24350.2.13.3.2
OBJECT IDENTIFIER

sysL2HideinternalGatewayAllow		1.3.6.1.4.1.24350.2.13.3.2.1
OBJECT IDENTIFIER

sysL2HideinternalGatewayAllowRelaydhcp		1.3.6.1.4.1.24350.2.13.3.2.1.1
arp for dhcp relay subnet
Status: current	Access: read-write
OBJECT-TYPE
	OCTET STRING

sysL2HideinternalGatewayDeny		1.3.6.1.4.1.24350.2.13.3.2.2
OBJECT IDENTIFIER

sysL2HideinternalGatewayDenyAll		1.3.6.1.4.1.24350.2.13.3.2.2.1
deny all proxy arps from gateway, unless .allowed
Status: current	Access: read-write
OBJECT-TYPE
	OCTET STRING

sysL2HideinternalGatewayDenyMesh		1.3.6.1.4.1.24350.2.13.3.2.2.2
hide mesh from proxy arp
Status: current	Access: read-write
OBJECT-TYPE
	OCTET STRING

sysLocation		1.3.6.1.4.1.24350.2.14
OBJECT IDENTIFIER

sysLocationGps		1.3.6.1.4.1.24350.2.14.1
OBJECT IDENTIFIER

sysLocationGpsAltitude		1.3.6.1.4.1.24350.2.14.1.1
gps altitude in meters
Status: current	Access: read-write
OBJECT-TYPE
	OCTET STRING

sysLocationGpsLatitude		1.3.6.1.4.1.24350.2.14.1.2
gps latitude in decimal degrees
Status: current	Access: read-write
OBJECT-TYPE
	OCTET STRING

sysLocationGpsLongitude		1.3.6.1.4.1.24350.2.14.1.3
gps longitude in decimal degrees
Status: current	Access: read-write
OBJECT-TYPE
	OCTET STRING

sysLocationPostal		1.3.6.1.4.1.24350.2.14.2
useful description of node's physical location
Status: current	Access: read-write
OBJECT-TYPE
	OCTET STRING

sysMainstub		1.3.6.1.4.1.24350.2.15
OBJECT IDENTIFIER

sysMainstubIf		1.3.6.1.4.1.24350.2.15.1
interface to multicast network
Status: current	Access: read-write
OBJECT-TYPE
	OCTET STRING

sysMainstubProxyarp		1.3.6.1.4.1.24350.2.15.2
proxy arp on multicast interface?
Status: current	Access: read-write
OBJECT-TYPE
	OCTET STRING

sysMonitor		1.3.6.1.4.1.24350.2.16
OBJECT IDENTIFIER

sysMonitorHealth		1.3.6.1.4.1.24350.2.16.1
OBJECT IDENTIFIER

sysMonitorHealthEnable		1.3.6.1.4.1.24350.2.16.1.1
enable health monitoring for gateway failover
Status: current	Access: read-write
OBJECT-TYPE
	OCTET STRING

sysMonitorHealthHost		1.3.6.1.4.1.24350.2.16.1.2
host to ping
Status: current	Access: read-write
OBJECT-TYPE
	OCTET STRING

sysNat		1.3.6.1.4.1.24350.2.17
OBJECT IDENTIFIER

sysNatEnable		1.3.6.1.4.1.24350.2.17.1
masquerading (on eth0, if gateway)
Status: current	Access: read-write
OBJECT-TYPE
	OCTET STRING

sysNetbios		1.3.6.1.4.1.24350.2.18
OBJECT IDENTIFIER

sysNetbiosServers		1.3.6.1.4.1.24350.2.18.1
space separated netbios server list
Status: current	Access: read-write
OBJECT-TYPE
	OCTET STRING

sysNets		1.3.6.1.4.1.24350.2.19
OBJECT IDENTIFIER

sysNetsExternal		1.3.6.1.4.1.24350.2.19.1
OBJECT IDENTIFIER

sysNetsExternalCombined		1.3.6.1.4.1.24350.2.19.1.1
coalesced .external.default, external.roamd, and .external.extra subnets
Status: current	Access: read-only
OBJECT-TYPE
	OCTET STRING

sysNetsExternalDefault		1.3.6.1.4.1.24350.2.19.1.2
subnets considered external to the mesh by default
Status: current	Access: read-only
OBJECT-TYPE
	OCTET STRING

sysNetsExternalExtra		1.3.6.1.4.1.24350.2.19.1.3
extra subnets to be considered external to the mesh
Status: current	Access: read-write
OBJECT-TYPE
	OCTET STRING

sysNetsInternal		1.3.6.1.4.1.24350.2.19.2
OBJECT IDENTIFIER

sysNetsInternalCombined		1.3.6.1.4.1.24350.2.19.2.1
coalesced .internal.default and internal.extra internal subnets
Status: current	Access: read-only
OBJECT-TYPE
	OCTET STRING

sysNetsInternalDefault		1.3.6.1.4.1.24350.2.19.2.2
default mesh-internal subnets
Status: current	Access: read-only
OBJECT-TYPE
	OCTET STRING

sysNetsInternalExtra		1.3.6.1.4.1.24350.2.19.2.3
added to .default internal subnets
Status: current	Access: read-write
OBJECT-TYPE
	OCTET STRING

sysNetsInternalFlexipdefault		1.3.6.1.4.1.24350.2.19.2.4
override the .nets.internal.default for flexip
Status: current	Access: read-write
OBJECT-TYPE
	OCTET STRING

sysOrganization		1.3.6.1.4.1.24350.2.20
OBJECT IDENTIFIER

sysOrganizationCity		1.3.6.1.4.1.24350.2.20.1
city or locality
Status: current	Access: read-write
OBJECT-TYPE
	OCTET STRING

sysOrganizationCountry		1.3.6.1.4.1.24350.2.20.2
2 letter country code
Status: current	Access: read-write
OBJECT-TYPE
	OCTET STRING

sysOrganizationName		1.3.6.1.4.1.24350.2.20.3
organization name
Status: current	Access: read-write
OBJECT-TYPE
	OCTET STRING

sysOrganizationState		1.3.6.1.4.1.24350.2.20.4
state or province
Status: current	Access: read-write
OBJECT-TYPE
	OCTET STRING

sysPassword		1.3.6.1.4.1.24350.2.21
OBJECT IDENTIFIER

sysPasswordAdmin		1.3.6.1.4.1.24350.2.21.1
admin account password
Status: current	Access: read-write
OBJECT-TYPE
	OCTET STRING

sysPasswordMonitor		1.3.6.1.4.1.24350.2.21.2
monitor account password
Status: current	Access: read-write
OBJECT-TYPE
	OCTET STRING

sysPlatform		1.3.6.1.4.1.24350.2.22
hardware platform
Status: current	Access: read-only
OBJECT-TYPE
	OCTET STRING

sysProvisioning		1.3.6.1.4.1.24350.2.23
OBJECT IDENTIFIER

sysProvisioningEnable		1.3.6.1.4.1.24350.2.23.1
enable OnRamp provisioning
Status: current	Access: read-write
OBJECT-TYPE
	OCTET STRING

sysRouting		1.3.6.1.4.1.24350.2.24
OBJECT IDENTIFIER

sysRoutingOspf		1.3.6.1.4.1.24350.2.24.1
enable OSPF dynamic routing
Status: current	Access: read-write
OBJECT-TYPE
	OCTET STRING

sysRoutingRip		1.3.6.1.4.1.24350.2.24.2
enable RIP dynamic routing
Status: current	Access: read-write
OBJECT-TYPE
	OCTET STRING

sysScheme		1.3.6.1.4.1.24350.2.25
wireless node type
Status: current	Access: read-write
OBJECT-TYPE
	OCTET STRING

sysShell		1.3.6.1.4.1.24350.2.26
OBJECT IDENTIFIER

sysShellTimeout		1.3.6.1.4.1.24350.2.26.1
shell inactivity timeout
Status: current	Access: read-write
OBJECT-TYPE
	INTEGER

sysSnmp		1.3.6.1.4.1.24350.2.27
OBJECT IDENTIFIER

sysSnmpCommunity		1.3.6.1.4.1.24350.2.27.1
OBJECT IDENTIFIER

sysSnmpCommunityRo		1.3.6.1.4.1.24350.2.27.1.1
ro community password
Status: current	Access: read-write
OBJECT-TYPE
	OCTET STRING

sysSnmpCommunityRw		1.3.6.1.4.1.24350.2.27.1.2
rw community password
Status: current	Access: read-write
OBJECT-TYPE
	OCTET STRING

sysSnmpCommunityTrap		1.3.6.1.4.1.24350.2.27.1.3
trap community password
Status: current	Access: read-write
OBJECT-TYPE
	OCTET STRING

sysSnmpContact		1.3.6.1.4.1.24350.2.27.2
snmp contact
Status: current	Access: read-write
OBJECT-TYPE
	OCTET STRING

sysSnmpLocation		1.3.6.1.4.1.24350.2.27.3
location (taken from sys.location.postal)
Status: current	Access: read-write
OBJECT-TYPE
	OCTET STRING

sysSnmpPort		1.3.6.1.4.1.24350.2.27.4
snmp port
Status: current	Access: read-write
OBJECT-TYPE
	INTEGER

sysSnmpTrap		1.3.6.1.4.1.24350.2.27.5
OBJECT IDENTIFIER

sysSnmpTrapHost		1.3.6.1.4.1.24350.2.27.5.1
trap host (trapsink)
Status: current	Access: read-write
OBJECT-TYPE
	OCTET STRING

sysSplash		1.3.6.1.4.1.24350.2.28
OBJECT IDENTIFIER

sysSplashAuth		1.3.6.1.4.1.24350.2.28.1
OBJECT IDENTIFIER

sysSplashAuthServer		1.3.6.1.4.1.24350.2.28.1.1
OBJECT IDENTIFIER

sysSplashAuthServerWlan1		1.3.6.1.4.1.24350.2.28.1.1.1
OBJECT IDENTIFIER

sysSplashAuthServerWlan1Enable		1.3.6.1.4.1.24350.2.28.1.1.1.1
require authentication
Status: current	Access: read-write
OBJECT-TYPE
	OCTET STRING

sysSplashAuthServerWlan1Host		1.3.6.1.4.1.24350.2.28.1.1.1.2
host for remote radius authentication
Status: current	Access: read-write
OBJECT-TYPE
	OCTET STRING

sysSplashAuthServerWlan1Port		1.3.6.1.4.1.24350.2.28.1.1.1.3
port for remote radius authentication
Status: current	Access: read-write
OBJECT-TYPE
	INTEGER

sysSplashAuthServerWlan1Secret		1.3.6.1.4.1.24350.2.28.1.1.1.4
shared secret for remote radius authentication
Status: current	Access: read-write
OBJECT-TYPE
	OCTET STRING

sysSplashAuthServerWlan2		1.3.6.1.4.1.24350.2.28.1.1.2
OBJECT IDENTIFIER

sysSplashAuthServerWlan2Enable		1.3.6.1.4.1.24350.2.28.1.1.2.1
require authentication
Status: current	Access: read-write
OBJECT-TYPE
	OCTET STRING

sysSplashAuthServerWlan2Host		1.3.6.1.4.1.24350.2.28.1.1.2.2
host for remote radius authentication
Status: current	Access: read-write
OBJECT-TYPE
	OCTET STRING

sysSplashAuthServerWlan2Port		1.3.6.1.4.1.24350.2.28.1.1.2.3
port for remote radius authentication
Status: current	Access: read-write
OBJECT-TYPE
	INTEGER

sysSplashAuthServerWlan2Secret		1.3.6.1.4.1.24350.2.28.1.1.2.4
shared secret for remote radius authentication
Status: current	Access: read-write
OBJECT-TYPE
	OCTET STRING

sysSplashAuthServerWlan3		1.3.6.1.4.1.24350.2.28.1.1.3
OBJECT IDENTIFIER

sysSplashAuthServerWlan3Enable		1.3.6.1.4.1.24350.2.28.1.1.3.1
require authentication
Status: current	Access: read-write
OBJECT-TYPE
	OCTET STRING

sysSplashAuthServerWlan3Host		1.3.6.1.4.1.24350.2.28.1.1.3.2
host for remote radius authentication
Status: current	Access: read-write
OBJECT-TYPE
	OCTET STRING

sysSplashAuthServerWlan3Port		1.3.6.1.4.1.24350.2.28.1.1.3.3
port for remote radius authentication
Status: current	Access: read-write
OBJECT-TYPE
	INTEGER

sysSplashAuthServerWlan3Secret		1.3.6.1.4.1.24350.2.28.1.1.3.4
shared secret for remote radius authentication
Status: current	Access: read-write
OBJECT-TYPE
	OCTET STRING

sysSplashAuthServerWlan4		1.3.6.1.4.1.24350.2.28.1.1.4
OBJECT IDENTIFIER

sysSplashAuthServerWlan4Enable		1.3.6.1.4.1.24350.2.28.1.1.4.1
require authentication
Status: current	Access: read-write
OBJECT-TYPE
	OCTET STRING

sysSplashAuthServerWlan4Host		1.3.6.1.4.1.24350.2.28.1.1.4.2
host for remote radius authentication
Status: current	Access: read-write
OBJECT-TYPE
	OCTET STRING

sysSplashAuthServerWlan4Port		1.3.6.1.4.1.24350.2.28.1.1.4.3
port for remote radius authentication
Status: current	Access: read-write
OBJECT-TYPE
	INTEGER

sysSplashAuthServerWlan4Secret		1.3.6.1.4.1.24350.2.28.1.1.4.4
shared secret for remote radius authentication
Status: current	Access: read-write
OBJECT-TYPE
	OCTET STRING

sysSplashBypasshosts		1.3.6.1.4.1.24350.2.28.2
comma separated list of hosts to bypass sign in
Status: current	Access: read-write
OBJECT-TYPE
	OCTET STRING

sysSplashEnable		1.3.6.1.4.1.24350.2.28.3
OBJECT IDENTIFIER

sysSplashEnableWlan1		1.3.6.1.4.1.24350.2.28.3.1
enable splash screen for wlan1
Status: current	Access: read-write
OBJECT-TYPE
	OCTET STRING

sysSplashEnableWlan2		1.3.6.1.4.1.24350.2.28.3.2
enable splash screen for wlan2
Status: current	Access: read-write
OBJECT-TYPE
	OCTET STRING

sysSplashEnableWlan3		1.3.6.1.4.1.24350.2.28.3.3
enable splash screen for wlan3
Status: current	Access: read-write
OBJECT-TYPE
	OCTET STRING

sysSplashEnableWlan4		1.3.6.1.4.1.24350.2.28.3.4
enable splash screen for wlan4
Status: current	Access: read-write
OBJECT-TYPE
	OCTET STRING

sysSplashExternal		1.3.6.1.4.1.24350.2.28.4
external network device, set by sys.scheme
Status: current	Access: read-write
OBJECT-TYPE
	OCTET STRING

sysSplashInternal		1.3.6.1.4.1.24350.2.28.5
internal network devices, set by sys.scheme
Status: current	Access: read-only
OBJECT-TYPE
	OCTET STRING

sysSplashTrustedmacs		1.3.6.1.4.1.24350.2.28.6
comma separated list of mac addresses than can pass
Status: current	Access: read-write
OBJECT-TYPE
	OCTET STRING

sysSplashUrl		1.3.6.1.4.1.24350.2.28.7
OBJECT IDENTIFIER

sysSplashUrlWlan1		1.3.6.1.4.1.24350.2.28.7.1
OBJECT IDENTIFIER

sysSplashUrlWlan1Error		1.3.6.1.4.1.24350.2.28.7.1.1
full url to page shown on login (internal) error
Status: current	Access: read-write
OBJECT-TYPE
	OCTET STRING

sysSplashUrlWlan1Fail		1.3.6.1.4.1.24350.2.28.7.1.2
full url to page shown on failed login
Status: current	Access: read-write
OBJECT-TYPE
	OCTET STRING

sysSplashUrlWlan1Login		1.3.6.1.4.1.24350.2.28.7.1.3
full url to desired login page
Status: current	Access: read-write
OBJECT-TYPE
	OCTET STRING

sysSplashUrlWlan1Success		1.3.6.1.4.1.24350.2.28.7.1.4
full url to page shown on successful login
Status: current	Access: read-write
OBJECT-TYPE
	OCTET STRING

sysSplashUrlWlan2		1.3.6.1.4.1.24350.2.28.7.2
OBJECT IDENTIFIER

sysSplashUrlWlan2Error		1.3.6.1.4.1.24350.2.28.7.2.1
full url to page shown on login (internal) error
Status: current	Access: read-write
OBJECT-TYPE
	OCTET STRING

sysSplashUrlWlan2Fail		1.3.6.1.4.1.24350.2.28.7.2.2
full url to page shown on failed login
Status: current	Access: read-write
OBJECT-TYPE
	OCTET STRING

sysSplashUrlWlan2Login		1.3.6.1.4.1.24350.2.28.7.2.3
full url to desired login page
Status: current	Access: read-write
OBJECT-TYPE
	OCTET STRING

sysSplashUrlWlan2Success		1.3.6.1.4.1.24350.2.28.7.2.4
full url to page shown on successful login
Status: current	Access: read-write
OBJECT-TYPE
	OCTET STRING

sysSplashUrlWlan3		1.3.6.1.4.1.24350.2.28.7.3
OBJECT IDENTIFIER

sysSplashUrlWlan3Error		1.3.6.1.4.1.24350.2.28.7.3.1
full url to page shown on login (internal) error
Status: current	Access: read-write
OBJECT-TYPE
	OCTET STRING

sysSplashUrlWlan3Fail		1.3.6.1.4.1.24350.2.28.7.3.2
full url to page shown on failed login
Status: current	Access: read-write
OBJECT-TYPE
	OCTET STRING

sysSplashUrlWlan3Login		1.3.6.1.4.1.24350.2.28.7.3.3
full url to desired login page
Status: current	Access: read-write
OBJECT-TYPE
	OCTET STRING

sysSplashUrlWlan3Success		1.3.6.1.4.1.24350.2.28.7.3.4
full url to page shown on successful login
Status: current	Access: read-write
OBJECT-TYPE
	OCTET STRING

sysSplashUrlWlan4		1.3.6.1.4.1.24350.2.28.7.4
OBJECT IDENTIFIER

sysSplashUrlWlan4Error		1.3.6.1.4.1.24350.2.28.7.4.1
full url to page shown on login (internal) error
Status: current	Access: read-write
OBJECT-TYPE
	OCTET STRING

sysSplashUrlWlan4Fail		1.3.6.1.4.1.24350.2.28.7.4.2
full url to page shown on failed login
Status: current	Access: read-write
OBJECT-TYPE
	OCTET STRING

sysSplashUrlWlan4Login		1.3.6.1.4.1.24350.2.28.7.4.3
full url to desired login page
Status: current	Access: read-write
OBJECT-TYPE
	OCTET STRING

sysSplashUrlWlan4Success		1.3.6.1.4.1.24350.2.28.7.4.4
full url to page shown on successful login
Status: current	Access: read-write
OBJECT-TYPE
	OCTET STRING

sysTime		1.3.6.1.4.1.24350.2.29
OBJECT IDENTIFIER

sysTimeRfc868		1.3.6.1.4.1.24350.2.29.1
OBJECT IDENTIFIER

sysTimeRfc868Server		1.3.6.1.4.1.24350.2.29.1.1
RFC868 time server name or address for gateway nodes
Status: current	Access: read-write
OBJECT-TYPE
	OCTET STRING

sysTimeSyncdelay		1.3.6.1.4.1.24350.2.29.2
how many seconds repeaters should delay syncing to gateway
Status: current	Access: read-write
OBJECT-TYPE
	INTEGER

sysUnits		1.3.6.1.4.1.24350.2.30
imperial (feet) or metric (meters)
Status: current	Access: read-write
OBJECT-TYPE
	OCTET STRING

firewall		1.3.6.1.4.1.24350.3
OBJECT IDENTIFIER

firewallConntrack		1.3.6.1.4.1.24350.3.1
OBJECT IDENTIFIER

firewallConntrackConnlimit		1.3.6.1.4.1.24350.3.1.1
OBJECT IDENTIFIER

firewallConntrackConnlimitConnections		1.3.6.1.4.1.24350.3.1.1.1
number of connections allowed per client
Status: current	Access: read-write
OBJECT-TYPE
	INTEGER

firewallConntrackConnlimitEnable		1.3.6.1.4.1.24350.3.1.1.2
limit the number of tcp connections per client
Status: current	Access: read-write
OBJECT-TYPE
	OCTET STRING

firewallConntrackTablesize		1.3.6.1.4.1.24350.3.1.2
size of connection tracking table
Status: current	Access: read-write
OBJECT-TYPE
	INTEGER

firewallConntrackTcptimeoutestablished		1.3.6.1.4.1.24350.3.1.3
tcp connections completely idle this many seconds can be dropped
Status: current	Access: read-write
OBJECT-TYPE
	INTEGER

firewallGateway		1.3.6.1.4.1.24350.3.2
OBJECT IDENTIFIER

firewallGatewayEnable		1.3.6.1.4.1.24350.3.2.1
prevent incoming connections past gateway node
Status: current	Access: read-write
OBJECT-TYPE
	OCTET STRING

firewallNode		1.3.6.1.4.1.24350.3.3
OBJECT IDENTIFIER

firewallNodeAllowc2c		1.3.6.1.4.1.24350.3.3.1
OBJECT IDENTIFIER

firewallNodeAllowc2cEth0		1.3.6.1.4.1.24350.3.3.1.1
allow clients to see each other if eth0.role=access
Status: current	Access: read-write
OBJECT-TYPE
	OCTET STRING

firewallNodeAllowc2cWlan1		1.3.6.1.4.1.24350.3.3.1.2
allow clients to see each other if wlan1.role=access
Status: current	Access: read-write
OBJECT-TYPE
	OCTET STRING

firewallNodeAllowc2cWlan2		1.3.6.1.4.1.24350.3.3.1.3
allow clients to see each other if wlan2.role=access
Status: current	Access: read-write
OBJECT-TYPE
	OCTET STRING

firewallNodeAllowc2cWlan3		1.3.6.1.4.1.24350.3.3.1.4
allow clients to see each other if wlan3.role=access
Status: current	Access: read-write
OBJECT-TYPE
	OCTET STRING

firewallNodeAllowc2cWlan4		1.3.6.1.4.1.24350.3.3.1.5
allow clients to see each other if wlan4.role=access
Status: current	Access: read-write
OBJECT-TYPE
	OCTET STRING

firewallNodeEnable		1.3.6.1.4.1.24350.3.3.2
enable firewall on the node
Status: current	Access: read-write
OBJECT-TYPE
	OCTET STRING

firewallNodeTcp		1.3.6.1.4.1.24350.3.3.3
OBJECT IDENTIFIER

firewallNodeTcpAllow		1.3.6.1.4.1.24350.3.3.3.1
OBJECT IDENTIFIER

firewallNodeTcpAllowDest		1.3.6.1.4.1.24350.3.3.3.1.1
tcp dest ports (space separated) to allow to this node
Status: current	Access: read-write
OBJECT-TYPE
	OCTET STRING

firewallNodeTcpAllowSource		1.3.6.1.4.1.24350.3.3.3.1.2
tcp source ports (space separated) to allow to this node
Status: current	Access: read-write
OBJECT-TYPE
	OCTET STRING

firewallNodeUdp		1.3.6.1.4.1.24350.3.3.4
OBJECT IDENTIFIER

firewallNodeUdpAllow		1.3.6.1.4.1.24350.3.3.4.1
OBJECT IDENTIFIER

firewallNodeUdpAllowDest		1.3.6.1.4.1.24350.3.3.4.1.1
udp dest ports (space separated) to allow to this node
Status: current	Access: read-write
OBJECT-TYPE
	OCTET STRING

firewallNodeUdpAllowSource		1.3.6.1.4.1.24350.3.3.4.1.2
udp source ports (space separated) to allow to this node
Status: current	Access: read-write
OBJECT-TYPE
	OCTET STRING

qos		1.3.6.1.4.1.24350.4
OBJECT IDENTIFIER

qosEnable		1.3.6.1.4.1.24350.4.1
qos enabled? if not, nothing else here matters.
Status: current	Access: read-write
OBJECT-TYPE
	OCTET STRING

qosExtra		1.3.6.1.4.1.24350.4.2
space separated list of extra = qos values
Status: current	Access: read-write
OBJECT-TYPE
	OCTET STRING

qosIn		1.3.6.1.4.1.24350.4.3
OBJECT IDENTIFIER

qosInDefault		1.3.6.1.4.1.24350.4.3.1
OBJECT IDENTIFIER

qosInDefaultFlowpriority		1.3.6.1.4.1.24350.4.3.1.1
input flow priority 0-99 or 'inherit' (higher is higher priority)
Status: current	Access: read-write
OBJECT-TYPE
	OCTET STRING

qosInDefaultHwpri		1.3.6.1.4.1.24350.4.3.1.2
OBJECT IDENTIFIER

qosInDefaultHwpriMax		1.3.6.1.4.1.24350.4.3.1.2.1
max hardware priority on output (1-4, 0 for default, or 'inherit')
Status: current	Access: read-write
OBJECT-TYPE
	OCTET STRING

qosInDefaultHwpriMin		1.3.6.1.4.1.24350.4.3.1.2.2
min hardware priority on output (1-4, 0 for default, or 'inherit')
Status: current	Access: read-write
OBJECT-TYPE
	OCTET STRING

qosInEth0		1.3.6.1.4.1.24350.4.3.2
OBJECT IDENTIFIER

qosInEth0Flowpriority		1.3.6.1.4.1.24350.4.3.2.1
input flow priority 0-99 or 'inherit' (higher is higher priority)
Status: current	Access: read-write
OBJECT-TYPE
	OCTET STRING

qosInEth0Hwpri		1.3.6.1.4.1.24350.4.3.2.2
OBJECT IDENTIFIER

qosInEth0HwpriMax		1.3.6.1.4.1.24350.4.3.2.2.1
max hardware priority on output (1-4, 0 for default, or 'inherit')
Status: current	Access: read-write
OBJECT-TYPE
	OCTET STRING

qosInEth0HwpriMin		1.3.6.1.4.1.24350.4.3.2.2.2
min hardware priority on output (1-4, 0 for default, or 'inherit')
Status: current	Access: read-write
OBJECT-TYPE
	OCTET STRING

qosInLocal		1.3.6.1.4.1.24350.4.3.3
OBJECT IDENTIFIER

qosInLocalFlowpriority		1.3.6.1.4.1.24350.4.3.3.1
input flow priority 0-99 or 'inherit' (higher is higher priority)
Status: current	Access: read-write
OBJECT-TYPE
	OCTET STRING

qosInLocalHwpri		1.3.6.1.4.1.24350.4.3.3.2
OBJECT IDENTIFIER

qosInLocalHwpriMax		1.3.6.1.4.1.24350.4.3.3.2.1
max hardware priority on output (1-4, 0 for default, or 'inherit')
Status: current	Access: read-write
OBJECT-TYPE
	OCTET STRING

qosInLocalHwpriMin		1.3.6.1.4.1.24350.4.3.3.2.2
min hardware priority on output (1-4, 0 for default, or 'inherit')
Status: current	Access: read-write
OBJECT-TYPE
	OCTET STRING

qosInWlan0		1.3.6.1.4.1.24350.4.3.4
OBJECT IDENTIFIER

qosInWlan0Flowpriority		1.3.6.1.4.1.24350.4.3.4.1
input flow priority 0-99 or 'inherit' (higher is higher priority)
Status: current	Access: read-write
OBJECT-TYPE
	OCTET STRING

qosInWlan0Hwpri		1.3.6.1.4.1.24350.4.3.4.2
OBJECT IDENTIFIER

qosInWlan0HwpriMax		1.3.6.1.4.1.24350.4.3.4.2.1
max hardware priority on output (1-4, 0 for default, or 'inherit')
Status: current	Access: read-write
OBJECT-TYPE
	OCTET STRING

qosInWlan0HwpriMin		1.3.6.1.4.1.24350.4.3.4.2.2
min hardware priority on output (1-4, 0 for default, or 'inherit')
Status: current	Access: read-write
OBJECT-TYPE
	OCTET STRING

qosInWlan1		1.3.6.1.4.1.24350.4.3.5
OBJECT IDENTIFIER

qosInWlan1Flowpriority		1.3.6.1.4.1.24350.4.3.5.1
input flow priority 0-99 or 'inherit' (higher is higher priority)
Status: current	Access: read-write
OBJECT-TYPE
	OCTET STRING

qosInWlan1Hwpri		1.3.6.1.4.1.24350.4.3.5.2
OBJECT IDENTIFIER

qosInWlan1HwpriMax		1.3.6.1.4.1.24350.4.3.5.2.1
max hardware priority on output (1-4, 0 for default, or 'inherit')
Status: current	Access: read-write
OBJECT-TYPE
	OCTET STRING

qosInWlan1HwpriMin		1.3.6.1.4.1.24350.4.3.5.2.2
min hardware priority on output (1-4, 0 for default, or 'inherit')
Status: current	Access: read-write
OBJECT-TYPE
	OCTET STRING

qosInWlan2		1.3.6.1.4.1.24350.4.3.6
OBJECT IDENTIFIER

qosInWlan2Flowpriority		1.3.6.1.4.1.24350.4.3.6.1
input flow priority 0-99 or 'inherit' (higher is higher priority)
Status: current	Access: read-write
OBJECT-TYPE
	OCTET STRING

qosInWlan2Hwpri		1.3.6.1.4.1.24350.4.3.6.2
OBJECT IDENTIFIER

qosInWlan2HwpriMax		1.3.6.1.4.1.24350.4.3.6.2.1
max hardware priority on output (1-4, 0 for default, or 'inherit')
Status: current	Access: read-write
OBJECT-TYPE
	OCTET STRING

qosInWlan2HwpriMin		1.3.6.1.4.1.24350.4.3.6.2.2
min hardware priority on output (1-4, 0 for default, or 'inherit')
Status: current	Access: read-write
OBJECT-TYPE
	OCTET STRING

qosInWlan3		1.3.6.1.4.1.24350.4.3.7
OBJECT IDENTIFIER

qosInWlan3Flowpriority		1.3.6.1.4.1.24350.4.3.7.1
input flow priority 0-99 or 'inherit' (higher is higher priority)
Status: current	Access: read-write
OBJECT-TYPE
	OCTET STRING

qosInWlan3Hwpri		1.3.6.1.4.1.24350.4.3.7.2
OBJECT IDENTIFIER

qosInWlan3HwpriMax		1.3.6.1.4.1.24350.4.3.7.2.1
max hardware priority on output (1-4, 0 for default, or 'inherit')
Status: current	Access: read-write
OBJECT-TYPE
	OCTET STRING

qosInWlan3HwpriMin		1.3.6.1.4.1.24350.4.3.7.2.2
min hardware priority on output (1-4, 0 for default, or 'inherit')
Status: current	Access: read-write
OBJECT-TYPE
	OCTET STRING

qosInWlan4		1.3.6.1.4.1.24350.4.3.8
OBJECT IDENTIFIER

qosInWlan4Flowpriority		1.3.6.1.4.1.24350.4.3.8.1
input flow priority 0-99 or 'inherit' (higher is higher priority)
Status: current	Access: read-write
OBJECT-TYPE
	OCTET STRING

qosInWlan4Hwpri		1.3.6.1.4.1.24350.4.3.8.2
OBJECT IDENTIFIER

qosInWlan4HwpriMax		1.3.6.1.4.1.24350.4.3.8.2.1
max hardware priority on output (1-4, 0 for default, or 'inherit')
Status: current	Access: read-write
OBJECT-TYPE
	OCTET STRING

qosInWlan4HwpriMin		1.3.6.1.4.1.24350.4.3.8.2.2
min hardware priority on output (1-4, 0 for default, or 'inherit')
Status: current	Access: read-write
OBJECT-TYPE
	OCTET STRING

qosOut		1.3.6.1.4.1.24350.4.4
OBJECT IDENTIFIER

qosOutDefault		1.3.6.1.4.1.24350.4.4.1
OBJECT IDENTIFIER

qosOutDefaultDefault		1.3.6.1.4.1.24350.4.4.1.1
OBJECT IDENTIFIER

qosOutDefaultDefaultLimit		1.3.6.1.4.1.24350.4.4.1.1.1
max bw for all data coming from default
Status: current	Access: read-write
OBJECT-TYPE
	OCTET STRING

qosOutDefaultDefaultReserve		1.3.6.1.4.1.24350.4.4.1.1.2
reserved bw for all data coming from default
Status: current	Access: read-write
OBJECT-TYPE
	OCTET STRING

qosOutDefaultEth0		1.3.6.1.4.1.24350.4.4.1.2
OBJECT IDENTIFIER

qosOutDefaultEth0Limit		1.3.6.1.4.1.24350.4.4.1.2.1
max bw for all data coming from eth0
Status: current	Access: read-write
OBJECT-TYPE
	OCTET STRING

qosOutDefaultEth0Reserve		1.3.6.1.4.1.24350.4.4.1.2.2
reserved bw for all data coming from eth0
Status: current	Access: read-write
OBJECT-TYPE
	OCTET STRING

qosOutDefaultLimit		1.3.6.1.4.1.24350.4.4.1.3
limit total output rate. *if blank, no other rates are used*
Status: current	Access: read-write
OBJECT-TYPE
	OCTET STRING

qosOutDefaultLocal		1.3.6.1.4.1.24350.4.4.1.4
OBJECT IDENTIFIER

qosOutDefaultLocalLimit		1.3.6.1.4.1.24350.4.4.1.4.1
max bw for all data coming from local
Status: current	Access: read-write
OBJECT-TYPE
	OCTET STRING

qosOutDefaultLocalReserve		1.3.6.1.4.1.24350.4.4.1.4.2
reserved bw for all data coming from local
Status: current	Access: read-write
OBJECT-TYPE
	OCTET STRING

qosOutDefaultWlan0		1.3.6.1.4.1.24350.4.4.1.5
OBJECT IDENTIFIER

qosOutDefaultWlan0Limit		1.3.6.1.4.1.24350.4.4.1.5.1
max bw for all data coming from wlan0
Status: current	Access: read-write
OBJECT-TYPE
	OCTET STRING

qosOutDefaultWlan0Reserve		1.3.6.1.4.1.24350.4.4.1.5.2
reserved bw for all data coming from wlan0
Status: current	Access: read-write
OBJECT-TYPE
	OCTET STRING

qosOutDefaultWlan1		1.3.6.1.4.1.24350.4.4.1.6
OBJECT IDENTIFIER

qosOutDefaultWlan1Limit		1.3.6.1.4.1.24350.4.4.1.6.1
max bw for all data coming from wlan1
Status: current	Access: read-write
OBJECT-TYPE
	OCTET STRING

qosOutDefaultWlan1Reserve		1.3.6.1.4.1.24350.4.4.1.6.2
reserved bw for all data coming from wlan1
Status: current	Access: read-write
OBJECT-TYPE
	OCTET STRING

qosOutDefaultWlan2		1.3.6.1.4.1.24350.4.4.1.7
OBJECT IDENTIFIER

qosOutDefaultWlan2Limit		1.3.6.1.4.1.24350.4.4.1.7.1
max bw for all data coming from wlan2
Status: current	Access: read-write
OBJECT-TYPE
	OCTET STRING

qosOutDefaultWlan2Reserve		1.3.6.1.4.1.24350.4.4.1.7.2
reserved bw for all data coming from wlan2
Status: current	Access: read-write
OBJECT-TYPE
	OCTET STRING

qosOutDefaultWlan3		1.3.6.1.4.1.24350.4.4.1.8
OBJECT IDENTIFIER

qosOutDefaultWlan3Limit		1.3.6.1.4.1.24350.4.4.1.8.1
max bw for all data coming from wlan3
Status: current	Access: read-write
OBJECT-TYPE
	OCTET STRING

qosOutDefaultWlan3Reserve		1.3.6.1.4.1.24350.4.4.1.8.2
reserved bw for all data coming from wlan3
Status: current	Access: read-write
OBJECT-TYPE
	OCTET STRING

qosOutDefaultWlan4		1.3.6.1.4.1.24350.4.4.1.9
OBJECT IDENTIFIER

qosOutDefaultWlan4Limit		1.3.6.1.4.1.24350.4.4.1.9.1
max bw for all data coming from wlan4
Status: current	Access: read-write
OBJECT-TYPE
	OCTET STRING

qosOutDefaultWlan4Reserve		1.3.6.1.4.1.24350.4.4.1.9.2
reserved bw for all data coming from wlan4
Status: current	Access: read-write
OBJECT-TYPE
	OCTET STRING

qosOutWlan0		1.3.6.1.4.1.24350.4.4.2
OBJECT IDENTIFIER

qosOutWlan0Default		1.3.6.1.4.1.24350.4.4.2.1
OBJECT IDENTIFIER

qosOutWlan0DefaultBe		1.3.6.1.4.1.24350.4.4.2.1.1
OBJECT IDENTIFIER

qosOutWlan0DefaultBeLimit		1.3.6.1.4.1.24350.4.4.2.1.1.1
max bw for BE data coming from default
Status: current	Access: read-write
OBJECT-TYPE
	OCTET STRING

qosOutWlan0DefaultBeReserve		1.3.6.1.4.1.24350.4.4.2.1.1.2
reserved bw for BE data coming from default
Status: current	Access: read-write
OBJECT-TYPE
	OCTET STRING

qosOutWlan0DefaultBk		1.3.6.1.4.1.24350.4.4.2.1.2
OBJECT IDENTIFIER

qosOutWlan0DefaultBkLimit		1.3.6.1.4.1.24350.4.4.2.1.2.1
max bw for BK data coming from default
Status: current	Access: read-write
OBJECT-TYPE
	OCTET STRING

qosOutWlan0DefaultBkReserve		1.3.6.1.4.1.24350.4.4.2.1.2.2
reserved bw for BK data coming from default
Status: current	Access: read-write
OBJECT-TYPE
	OCTET STRING

qosOutWlan0DefaultLimit		1.3.6.1.4.1.24350.4.4.2.1.3
max bw for all data coming from default
Status: current	Access: read-write
OBJECT-TYPE
	OCTET STRING

qosOutWlan0DefaultReserve		1.3.6.1.4.1.24350.4.4.2.1.4
reserved bw for all data coming from default
Status: current	Access: read-write
OBJECT-TYPE
	OCTET STRING

qosOutWlan0DefaultVi		1.3.6.1.4.1.24350.4.4.2.1.5
OBJECT IDENTIFIER

qosOutWlan0DefaultViLimit		1.3.6.1.4.1.24350.4.4.2.1.5.1
max bw for VI data coming from default
Status: current	Access: read-write
OBJECT-TYPE
	OCTET STRING

qosOutWlan0DefaultViReserve		1.3.6.1.4.1.24350.4.4.2.1.5.2
reserved bw for VI data coming from default
Status: current	Access: read-write
OBJECT-TYPE
	OCTET STRING

qosOutWlan0DefaultVo		1.3.6.1.4.1.24350.4.4.2.1.6
OBJECT IDENTIFIER

qosOutWlan0DefaultVoLimit		1.3.6.1.4.1.24350.4.4.2.1.6.1
max bw for VO data coming from default
Status: current	Access: read-write
OBJECT-TYPE
	OCTET STRING

qosOutWlan0DefaultVoReserve		1.3.6.1.4.1.24350.4.4.2.1.6.2
reserved bw for VO data coming from default
Status: current	Access: read-write
OBJECT-TYPE
	OCTET STRING

qosOutWlan0Eth0		1.3.6.1.4.1.24350.4.4.2.2
OBJECT IDENTIFIER

qosOutWlan0Eth0Be		1.3.6.1.4.1.24350.4.4.2.2.1
OBJECT IDENTIFIER

qosOutWlan0Eth0BeLimit		1.3.6.1.4.1.24350.4.4.2.2.1.1
max bw for BE data coming from eth0
Status: current	Access: read-write
OBJECT-TYPE
	OCTET STRING

qosOutWlan0Eth0BeReserve		1.3.6.1.4.1.24350.4.4.2.2.1.2
reserved bw for BE data coming from eth0
Status: current	Access: read-write
OBJECT-TYPE
	OCTET STRING

qosOutWlan0Eth0Bk		1.3.6.1.4.1.24350.4.4.2.2.2
OBJECT IDENTIFIER

qosOutWlan0Eth0BkLimit		1.3.6.1.4.1.24350.4.4.2.2.2.1
max bw for BK data coming from eth0
Status: current	Access: read-write
OBJECT-TYPE
	OCTET STRING

qosOutWlan0Eth0BkReserve		1.3.6.1.4.1.24350.4.4.2.2.2.2
reserved bw for BK data coming from eth0
Status: current	Access: read-write
OBJECT-TYPE
	OCTET STRING

qosOutWlan0Eth0Limit		1.3.6.1.4.1.24350.4.4.2.2.3
max bw for all data coming from eth0
Status: current	Access: read-write
OBJECT-TYPE
	OCTET STRING

qosOutWlan0Eth0Reserve		1.3.6.1.4.1.24350.4.4.2.2.4
reserved bw for all data coming from eth0
Status: current	Access: read-write
OBJECT-TYPE
	OCTET STRING

qosOutWlan0Eth0Vi		1.3.6.1.4.1.24350.4.4.2.2.5
OBJECT IDENTIFIER

qosOutWlan0Eth0ViLimit		1.3.6.1.4.1.24350.4.4.2.2.5.1
max bw for VI data coming from eth0
Status: current	Access: read-write
OBJECT-TYPE
	OCTET STRING

qosOutWlan0Eth0ViReserve		1.3.6.1.4.1.24350.4.4.2.2.5.2
reserved bw for VI data coming from eth0
Status: current	Access: read-write
OBJECT-TYPE
	OCTET STRING

qosOutWlan0Eth0Vo		1.3.6.1.4.1.24350.4.4.2.2.6
OBJECT IDENTIFIER

qosOutWlan0Eth0VoLimit		1.3.6.1.4.1.24350.4.4.2.2.6.1
max bw for VO data coming from eth0
Status: current	Access: read-write
OBJECT-TYPE
	OCTET STRING

qosOutWlan0Eth0VoReserve		1.3.6.1.4.1.24350.4.4.2.2.6.2
reserved bw for VO data coming from eth0
Status: current	Access: read-write
OBJECT-TYPE
	OCTET STRING

qosOutWlan0Limit		1.3.6.1.4.1.24350.4.4.2.3
limit total output rate. *if blank, no other rates are used*
Status: current	Access: read-write
OBJECT-TYPE
	OCTET STRING

qosOutWlan0Local		1.3.6.1.4.1.24350.4.4.2.4
OBJECT IDENTIFIER

qosOutWlan0LocalBe		1.3.6.1.4.1.24350.4.4.2.4.1
OBJECT IDENTIFIER

qosOutWlan0LocalBeLimit		1.3.6.1.4.1.24350.4.4.2.4.1.1
max bw for BE data coming from local
Status: current	Access: read-write
OBJECT-TYPE
	OCTET STRING

qosOutWlan0LocalBeReserve		1.3.6.1.4.1.24350.4.4.2.4.1.2
reserved bw for BE data coming from local
Status: current	Access: read-write
OBJECT-TYPE
	OCTET STRING

qosOutWlan0LocalBk		1.3.6.1.4.1.24350.4.4.2.4.2
OBJECT IDENTIFIER

qosOutWlan0LocalBkLimit		1.3.6.1.4.1.24350.4.4.2.4.2.1
max bw for BK data coming from local
Status: current	Access: read-write
OBJECT-TYPE
	OCTET STRING

qosOutWlan0LocalBkReserve		1.3.6.1.4.1.24350.4.4.2.4.2.2
reserved bw for BK data coming from local
Status: current	Access: read-write
OBJECT-TYPE
	OCTET STRING

qosOutWlan0LocalLimit		1.3.6.1.4.1.24350.4.4.2.4.3
max bw for all data coming from local
Status: current	Access: read-write
OBJECT-TYPE
	OCTET STRING

qosOutWlan0LocalReserve		1.3.6.1.4.1.24350.4.4.2.4.4
reserved bw for all data coming from local
Status: current	Access: read-write
OBJECT-TYPE
	OCTET STRING

qosOutWlan0LocalVi		1.3.6.1.4.1.24350.4.4.2.4.5
OBJECT IDENTIFIER

qosOutWlan0LocalViLimit		1.3.6.1.4.1.24350.4.4.2.4.5.1
max bw for VI data coming from local
Status: current	Access: read-write
OBJECT-TYPE
	OCTET STRING

qosOutWlan0LocalViReserve		1.3.6.1.4.1.24350.4.4.2.4.5.2
reserved bw for VI data coming from local
Status: current	Access: read-write
OBJECT-TYPE
	OCTET STRING

qosOutWlan0LocalVo		1.3.6.1.4.1.24350.4.4.2.4.6
OBJECT IDENTIFIER

qosOutWlan0LocalVoLimit		1.3.6.1.4.1.24350.4.4.2.4.6.1
max bw for VO data coming from local
Status: current	Access: read-write
OBJECT-TYPE
	OCTET STRING

qosOutWlan0LocalVoReserve		1.3.6.1.4.1.24350.4.4.2.4.6.2
reserved bw for VO data coming from local
Status: current	Access: read-write
OBJECT-TYPE
	OCTET STRING

qosOutWlan0Wlan0		1.3.6.1.4.1.24350.4.4.2.5
OBJECT IDENTIFIER

qosOutWlan0Wlan0Be		1.3.6.1.4.1.24350.4.4.2.5.1
OBJECT IDENTIFIER

qosOutWlan0Wlan0BeLimit		1.3.6.1.4.1.24350.4.4.2.5.1.1
max bw for BE data coming from wlan0
Status: current	Access: read-write
OBJECT-TYPE
	OCTET STRING

qosOutWlan0Wlan0BeReserve		1.3.6.1.4.1.24350.4.4.2.5.1.2
reserved bw for BE data coming from wlan0
Status: current	Access: read-write
OBJECT-TYPE
	OCTET STRING

qosOutWlan0Wlan0Bk		1.3.6.1.4.1.24350.4.4.2.5.2
OBJECT IDENTIFIER

qosOutWlan0Wlan0BkLimit		1.3.6.1.4.1.24350.4.4.2.5.2.1
max bw for BK data coming from wlan0
Status: current	Access: read-write
OBJECT-TYPE
	OCTET STRING

qosOutWlan0Wlan0BkReserve		1.3.6.1.4.1.24350.4.4.2.5.2.2
reserved bw for BK data coming from wlan0
Status: current	Access: read-write
OBJECT-TYPE
	OCTET STRING

qosOutWlan0Wlan0Limit		1.3.6.1.4.1.24350.4.4.2.5.3
max bw for all data coming from wlan0
Status: current	Access: read-write
OBJECT-TYPE
	OCTET STRING

qosOutWlan0Wlan0Reserve		1.3.6.1.4.1.24350.4.4.2.5.4
reserved bw for all data coming from wlan0
Status: current	Access: read-write
OBJECT-TYPE
	OCTET STRING

qosOutWlan0Wlan0Vi		1.3.6.1.4.1.24350.4.4.2.5.5
OBJECT IDENTIFIER

qosOutWlan0Wlan0ViLimit		1.3.6.1.4.1.24350.4.4.2.5.5.1
max bw for VI data coming from wlan0
Status: current	Access: read-write
OBJECT-TYPE
	OCTET STRING

qosOutWlan0Wlan0ViReserve		1.3.6.1.4.1.24350.4.4.2.5.5.2
reserved bw for VI data coming from wlan0
Status: current	Access: read-write
OBJECT-TYPE
	OCTET STRING

qosOutWlan0Wlan0Vo		1.3.6.1.4.1.24350.4.4.2.5.6
OBJECT IDENTIFIER

qosOutWlan0Wlan0VoLimit		1.3.6.1.4.1.24350.4.4.2.5.6.1
max bw for VO data coming from wlan0
Status: current	Access: read-write
OBJECT-TYPE
	OCTET STRING

qosOutWlan0Wlan0VoReserve		1.3.6.1.4.1.24350.4.4.2.5.6.2
reserved bw for VO data coming from wlan0
Status: current	Access: read-write
OBJECT-TYPE
	OCTET STRING

qosOutWlan0Wlan1		1.3.6.1.4.1.24350.4.4.2.6
OBJECT IDENTIFIER

qosOutWlan0Wlan1Be		1.3.6.1.4.1.24350.4.4.2.6.1
OBJECT IDENTIFIER

qosOutWlan0Wlan1BeLimit		1.3.6.1.4.1.24350.4.4.2.6.1.1
max bw for BE data coming from wlan1
Status: current	Access: read-write
OBJECT-TYPE
	OCTET STRING

qosOutWlan0Wlan1BeReserve		1.3.6.1.4.1.24350.4.4.2.6.1.2
reserved bw for BE data coming from wlan1
Status: current	Access: read-write
OBJECT-TYPE
	OCTET STRING

qosOutWlan0Wlan1Bk		1.3.6.1.4.1.24350.4.4.2.6.2
OBJECT IDENTIFIER

qosOutWlan0Wlan1BkLimit		1.3.6.1.4.1.24350.4.4.2.6.2.1
max bw for BK data coming from wlan1
Status: current	Access: read-write
OBJECT-TYPE
	OCTET STRING

qosOutWlan0Wlan1BkReserve		1.3.6.1.4.1.24350.4.4.2.6.2.2
reserved bw for BK data coming from wlan1
Status: current	Access: read-write
OBJECT-TYPE
	OCTET STRING

qosOutWlan0Wlan1Limit		1.3.6.1.4.1.24350.4.4.2.6.3
max bw for all data coming from wlan1
Status: current	Access: read-write
OBJECT-TYPE
	OCTET STRING

qosOutWlan0Wlan1Reserve		1.3.6.1.4.1.24350.4.4.2.6.4
reserved bw for all data coming from wlan1
Status: current	Access: read-write
OBJECT-TYPE
	OCTET STRING

qosOutWlan0Wlan1Vi		1.3.6.1.4.1.24350.4.4.2.6.5
OBJECT IDENTIFIER

qosOutWlan0Wlan1ViLimit		1.3.6.1.4.1.24350.4.4.2.6.5.1
max bw for VI data coming from wlan1
Status: current	Access: read-write
OBJECT-TYPE
	OCTET STRING

qosOutWlan0Wlan1ViReserve		1.3.6.1.4.1.24350.4.4.2.6.5.2
reserved bw for VI data coming from wlan1
Status: current	Access: read-write
OBJECT-TYPE
	OCTET STRING

qosOutWlan0Wlan1Vo		1.3.6.1.4.1.24350.4.4.2.6.6
OBJECT IDENTIFIER

qosOutWlan0Wlan1VoLimit		1.3.6.1.4.1.24350.4.4.2.6.6.1
max bw for VO data coming from wlan1
Status: current	Access: read-write
OBJECT-TYPE
	OCTET STRING

qosOutWlan0Wlan1VoReserve		1.3.6.1.4.1.24350.4.4.2.6.6.2
reserved bw for VO data coming from wlan1
Status: current	Access: read-write
OBJECT-TYPE
	OCTET STRING

qosOutWlan0Wlan2		1.3.6.1.4.1.24350.4.4.2.7
OBJECT IDENTIFIER

qosOutWlan0Wlan2Be		1.3.6.1.4.1.24350.4.4.2.7.1
OBJECT IDENTIFIER

qosOutWlan0Wlan2BeLimit		1.3.6.1.4.1.24350.4.4.2.7.1.1
max bw for BE data coming from wlan2
Status: current	Access: read-write
OBJECT-TYPE
	OCTET STRING

qosOutWlan0Wlan2BeReserve		1.3.6.1.4.1.24350.4.4.2.7.1.2
reserved bw for BE data coming from wlan2
Status: current	Access: read-write
OBJECT-TYPE
	OCTET STRING

qosOutWlan0Wlan2Bk		1.3.6.1.4.1.24350.4.4.2.7.2
OBJECT IDENTIFIER

qosOutWlan0Wlan2BkLimit		1.3.6.1.4.1.24350.4.4.2.7.2.1
max bw for BK data coming from wlan2
Status: current	Access: read-write
OBJECT-TYPE
	OCTET STRING

qosOutWlan0Wlan2BkReserve		1.3.6.1.4.1.24350.4.4.2.7.2.2
reserved bw for BK data coming from wlan2
Status: current	Access: read-write
OBJECT-TYPE
	OCTET STRING

qosOutWlan0Wlan2Limit		1.3.6.1.4.1.24350.4.4.2.7.3
max bw for all data coming from wlan2
Status: current	Access: read-write
OBJECT-TYPE
	OCTET STRING

qosOutWlan0Wlan2Reserve		1.3.6.1.4.1.24350.4.4.2.7.4
reserved bw for all data coming from wlan2
Status: current	Access: read-write
OBJECT-TYPE
	OCTET STRING

qosOutWlan0Wlan2Vi		1.3.6.1.4.1.24350.4.4.2.7.5
OBJECT IDENTIFIER

qosOutWlan0Wlan2ViLimit		1.3.6.1.4.1.24350.4.4.2.7.5.1
max bw for VI data coming from wlan2
Status: current	Access: read-write
OBJECT-TYPE
	OCTET STRING

qosOutWlan0Wlan2ViReserve		1.3.6.1.4.1.24350.4.4.2.7.5.2
reserved bw for VI data coming from wlan2
Status: current	Access: read-write
OBJECT-TYPE
	OCTET STRING

qosOutWlan0Wlan2Vo		1.3.6.1.4.1.24350.4.4.2.7.6
OBJECT IDENTIFIER

qosOutWlan0Wlan2VoLimit		1.3.6.1.4.1.24350.4.4.2.7.6.1
max bw for VO data coming from wlan2
Status: current	Access: read-write
OBJECT-TYPE
	OCTET STRING

qosOutWlan0Wlan2VoReserve		1.3.6.1.4.1.24350.4.4.2.7.6.2
reserved bw for VO data coming from wlan2
Status: current	Access: read-write
OBJECT-TYPE
	OCTET STRING

qosOutWlan0Wlan3		1.3.6.1.4.1.24350.4.4.2.8
OBJECT IDENTIFIER

qosOutWlan0Wlan3Be		1.3.6.1.4.1.24350.4.4.2.8.1
OBJECT IDENTIFIER

qosOutWlan0Wlan3BeLimit		1.3.6.1.4.1.24350.4.4.2.8.1.1
max bw for BE data coming from wlan3
Status: current	Access: read-write
OBJECT-TYPE
	OCTET STRING

qosOutWlan0Wlan3BeReserve		1.3.6.1.4.1.24350.4.4.2.8.1.2
reserved bw for BE data coming from wlan3
Status: current	Access: read-write
OBJECT-TYPE
	OCTET STRING

qosOutWlan0Wlan3Bk		1.3.6.1.4.1.24350.4.4.2.8.2
OBJECT IDENTIFIER

qosOutWlan0Wlan3BkLimit		1.3.6.1.4.1.24350.4.4.2.8.2.1
max bw for BK data coming from wlan3
Status: current	Access: read-write
OBJECT-TYPE
	OCTET STRING

qosOutWlan0Wlan3BkReserve		1.3.6.1.4.1.24350.4.4.2.8.2.2
reserved bw for BK data coming from wlan3
Status: current	Access: read-write
OBJECT-TYPE
	OCTET STRING

qosOutWlan0Wlan3Limit		1.3.6.1.4.1.24350.4.4.2.8.3
max bw for all data coming from wlan3
Status: current	Access: read-write
OBJECT-TYPE
	OCTET STRING

qosOutWlan0Wlan3Reserve		1.3.6.1.4.1.24350.4.4.2.8.4
reserved bw for all data coming from wlan3
Status: current	Access: read-write
OBJECT-TYPE
	OCTET STRING

qosOutWlan0Wlan3Vi		1.3.6.1.4.1.24350.4.4.2.8.5
OBJECT IDENTIFIER

qosOutWlan0Wlan3ViLimit		1.3.6.1.4.1.24350.4.4.2.8.5.1
max bw for VI data coming from wlan3
Status: current	Access: read-write
OBJECT-TYPE
	OCTET STRING

qosOutWlan0Wlan3ViReserve		1.3.6.1.4.1.24350.4.4.2.8.5.2
reserved bw for VI data coming from wlan3
Status: current	Access: read-write
OBJECT-TYPE
	OCTET STRING

qosOutWlan0Wlan3Vo		1.3.6.1.4.1.24350.4.4.2.8.6
OBJECT IDENTIFIER

qosOutWlan0Wlan3VoLimit		1.3.6.1.4.1.24350.4.4.2.8.6.1
max bw for VO data coming from wlan3
Status: current	Access: read-write
OBJECT-TYPE
	OCTET STRING

qosOutWlan0Wlan3VoReserve		1.3.6.1.4.1.24350.4.4.2.8.6.2
reserved bw for VO data coming from wlan3
Status: current	Access: read-write
OBJECT-TYPE
	OCTET STRING

qosOutWlan0Wlan4		1.3.6.1.4.1.24350.4.4.2.9
OBJECT IDENTIFIER

qosOutWlan0Wlan4Be		1.3.6.1.4.1.24350.4.4.2.9.1
OBJECT IDENTIFIER

qosOutWlan0Wlan4BeLimit		1.3.6.1.4.1.24350.4.4.2.9.1.1
max bw for BE data coming from wlan4
Status: current	Access: read-write
OBJECT-TYPE
	OCTET STRING

qosOutWlan0Wlan4BeReserve		1.3.6.1.4.1.24350.4.4.2.9.1.2
reserved bw for BE data coming from wlan4
Status: current	Access: read-write
OBJECT-TYPE
	OCTET STRING

qosOutWlan0Wlan4Bk		1.3.6.1.4.1.24350.4.4.2.9.2
OBJECT IDENTIFIER

qosOutWlan0Wlan4BkLimit		1.3.6.1.4.1.24350.4.4.2.9.2.1
max bw for BK data coming from wlan4
Status: current	Access: read-write
OBJECT-TYPE
	OCTET STRING

qosOutWlan0Wlan4BkReserve		1.3.6.1.4.1.24350.4.4.2.9.2.2
reserved bw for BK data coming from wlan4
Status: current	Access: read-write
OBJECT-TYPE
	OCTET STRING

qosOutWlan0Wlan4Limit		1.3.6.1.4.1.24350.4.4.2.9.3
max bw for all data coming from wlan4
Status: current	Access: read-write
OBJECT-TYPE
	OCTET STRING

qosOutWlan0Wlan4Reserve		1.3.6.1.4.1.24350.4.4.2.9.4
reserved bw for all data coming from wlan4
Status: current	Access: read-write
OBJECT-TYPE
	OCTET STRING

qosOutWlan0Wlan4Vi		1.3.6.1.4.1.24350.4.4.2.9.5
OBJECT IDENTIFIER

qosOutWlan0Wlan4ViLimit		1.3.6.1.4.1.24350.4.4.2.9.5.1
max bw for VI data coming from wlan4
Status: current	Access: read-write
OBJECT-TYPE
	OCTET STRING

qosOutWlan0Wlan4ViReserve		1.3.6.1.4.1.24350.4.4.2.9.5.2
reserved bw for VI data coming from wlan4
Status: current	Access: read-write
OBJECT-TYPE
	OCTET STRING

qosOutWlan0Wlan4Vo		1.3.6.1.4.1.24350.4.4.2.9.6
OBJECT IDENTIFIER

qosOutWlan0Wlan4VoLimit		1.3.6.1.4.1.24350.4.4.2.9.6.1
max bw for VO data coming from wlan4
Status: current	Access: read-write
OBJECT-TYPE
	OCTET STRING

qosOutWlan0Wlan4VoReserve		1.3.6.1.4.1.24350.4.4.2.9.6.2
reserved bw for VO data coming from wlan4
Status: current	Access: read-write
OBJECT-TYPE
	OCTET STRING

logs		1.3.6.1.4.1.24350.5
OBJECT IDENTIFIER

logsMconfd		1.3.6.1.4.1.24350.5.1
OBJECT IDENTIFIER

logsMconfdFiles		1.3.6.1.4.1.24350.5.1.1
number of old files kept
Status: current	Access: read-write
OBJECT-TYPE
	INTEGER

logsMconfdSize		1.3.6.1.4.1.24350.5.1.2
maximum file size in bytes
Status: current	Access: read-write
OBJECT-TYPE
	OCTET STRING

logsSecure		1.3.6.1.4.1.24350.5.2
OBJECT IDENTIFIER

logsSecureFiles		1.3.6.1.4.1.24350.5.2.1
number of old files kept
Status: current	Access: read-write
OBJECT-TYPE
	INTEGER

logsSecureSize		1.3.6.1.4.1.24350.5.2.2
maximum file size in bytes
Status: current	Access: read-write
OBJECT-TYPE
	OCTET STRING

logsSnmp		1.3.6.1.4.1.24350.5.3
OBJECT IDENTIFIER

logsSnmpFiles		1.3.6.1.4.1.24350.5.3.1
number of old files kept
Status: current	Access: read-write
OBJECT-TYPE
	INTEGER

logsSnmpSize		1.3.6.1.4.1.24350.5.3.2
maximum file size in bytes
Status: current	Access: read-write
OBJECT-TYPE
	OCTET STRING

logsSyslog		1.3.6.1.4.1.24350.5.4
OBJECT IDENTIFIER

logsSyslogFiles		1.3.6.1.4.1.24350.5.4.1
number of old files kept
Status: current	Access: read-write
OBJECT-TYPE
	INTEGER

logsSyslogSize		1.3.6.1.4.1.24350.5.4.2
maximum file size in bytes
Status: current	Access: read-write
OBJECT-TYPE
	OCTET STRING

eth0		1.3.6.1.4.1.24350.6
OBJECT IDENTIFIER

eth0Acl		1.3.6.1.4.1.24350.6.1
OBJECT IDENTIFIER

eth0AclMode		1.3.6.1.4.1.24350.6.1.1
access control list mode ( 'none', 'whitelist', 'blacklist' )
Status: current	Access: read-write
OBJECT-TYPE
	OCTET STRING

eth0Dhcp		1.3.6.1.4.1.24350.6.2
OBJECT IDENTIFIER

eth0DhcpAlwaysbroadcast		1.3.6.1.4.1.24350.6.2.1
always broadcast dhcp responses
Status: current	Access: read-write
OBJECT-TYPE
	OCTET STRING

eth0DhcpDefaultleasetime		1.3.6.1.4.1.24350.6.2.2
default dhcp lease expiration in seconds
Status: current	Access: read-write
OBJECT-TYPE
	INTEGER

eth0DhcpMaxleasetime		1.3.6.1.4.1.24350.6.2.3
maximum requestable dhcp lease expiration in seconds
Status: current	Access: read-write
OBJECT-TYPE
	INTEGER

eth0DhcpRelay		1.3.6.1.4.1.24350.6.2.4
OBJECT IDENTIFIER

eth0DhcpRelayEnable		1.3.6.1.4.1.24350.6.2.4.1
use dhcp relay (if sys.dhcp.relay.enable=yes)
Status: current	Access: read-write
OBJECT-TYPE
	OCTET STRING

eth0DhcpReserve		1.3.6.1.4.1.24350.6.2.5
ip addresses to reserve at bottom of range for static assignments
Status: current	Access: read-write
OBJECT-TYPE
	INTEGER

eth0DhcpRole		1.3.6.1.4.1.24350.6.2.6
interface dhcp role (none, client, server)
Status: current	Access: read-write
OBJECT-TYPE
	OCTET STRING

eth0Enable		1.3.6.1.4.1.24350.6.3
interface is enabled
Status: current	Access: read-write
OBJECT-TYPE
	OCTET STRING

eth0If		1.3.6.1.4.1.24350.6.4
interface associated with this module
Status: current	Access: read-only
OBJECT-TYPE
	OCTET STRING

eth0Ip		1.3.6.1.4.1.24350.6.5
OBJECT IDENTIFIER

eth0IpAddress		1.3.6.1.4.1.24350.6.5.1
ip address
Status: current	Access: read-only
OBJECT-TYPE
	OCTET STRING

eth0IpAddressforce		1.3.6.1.4.1.24350.6.5.2
override .ip.address (or blank)
Status: current	Access: read-write
OBJECT-TYPE
	OCTET STRING

eth0IpBroadcast		1.3.6.1.4.1.24350.6.5.3
broadcast address
Status: current	Access: read-only
OBJECT-TYPE
	OCTET STRING

eth0IpBroadcastforce		1.3.6.1.4.1.24350.6.5.4
override .ip.broadcast (or blank)
Status: current	Access: read-write
OBJECT-TYPE
	OCTET STRING

eth0IpGateway		1.3.6.1.4.1.24350.6.5.5
gateway address
Status: current	Access: read-only
OBJECT-TYPE
	OCTET STRING

eth0IpGatewayforce		1.3.6.1.4.1.24350.6.5.6
override .ip.gateway (or blank)
Status: current	Access: read-write
OBJECT-TYPE
	OCTET STRING

eth0IpImplicit		1.3.6.1.4.1.24350.6.5.7
OBJECT IDENTIFIER

eth0IpImplicitSize		1.3.6.1.4.1.24350.6.5.7.1
OBJECT IDENTIFIER

eth0IpImplicitSizeActual		1.3.6.1.4.1.24350.6.5.7.1.1
actual size of assigned address range
Status: current	Access: read-only
OBJECT-TYPE
	INTEGER

eth0IpImplicitSizeRequested		1.3.6.1.4.1.24350.6.5.7.1.2
requested size of address range (multiple of 32 minus 1)
Status: current	Access: read-write
OBJECT-TYPE
	OCTET STRING

eth0IpImplicitStart		1.3.6.1.4.1.24350.6.5.7.2
OBJECT IDENTIFIER

eth0IpImplicitStartActual		1.3.6.1.4.1.24350.6.5.7.2.1
actual assigned fourth octet
Status: current	Access: read-only
OBJECT-TYPE
	INTEGER

eth0IpImplicitStartRequested		1.3.6.1.4.1.24350.6.5.7.2.2
requested interface fourth octet (multiple of 32 plus 1)
Status: current	Access: read-write
OBJECT-TYPE
	OCTET STRING

eth0IpNetmask		1.3.6.1.4.1.24350.6.5.8
network mask
Status: current	Access: read-only
OBJECT-TYPE
	OCTET STRING

eth0IpNetmaskforce		1.3.6.1.4.1.24350.6.5.9
override .ip.netmask (or blank)
Status: current	Access: read-write
OBJECT-TYPE
	OCTET STRING

eth0Role		1.3.6.1.4.1.24350.6.6
intended interface role (gateway, access, bridge)
Status: current	Access: read-write
OBJECT-TYPE
	OCTET STRING

eth0Routes		1.3.6.1.4.1.24350.6.7
OBJECT IDENTIFIER

eth0RoutesStatic		1.3.6.1.4.1.24350.6.7.1
static routes for this interface
Status: current	Access: read-write
OBJECT-TYPE
	OCTET STRING

eth0Vlan		1.3.6.1.4.1.24350.6.8
OBJECT IDENTIFIER

eth0VlanEnable		1.3.6.1.4.1.24350.6.8.1
use a vlan for this interface
Status: current	Access: read-write
OBJECT-TYPE
	OCTET STRING

eth0VlanId		1.3.6.1.4.1.24350.6.8.2
vlan id (0 and 1 are usually reserved)
Status: current	Access: read-write
OBJECT-TYPE
	INTEGER

eth0Vpn		1.3.6.1.4.1.24350.6.9
OBJECT IDENTIFIER

eth0VpnDevice		1.3.6.1.4.1.24350.6.9.1
device type (tap or tun)
Status: current	Access: read-write
OBJECT-TYPE
	OCTET STRING

eth0VpnEnable		1.3.6.1.4.1.24350.6.9.2
enable vpn on gateway node
Status: current	Access: read-write
OBJECT-TYPE
	OCTET STRING

eth0VpnKeyfile		1.3.6.1.4.1.24350.6.9.3
base name of crt/key files
Status: current	Access: read-write
OBJECT-TYPE
	OCTET STRING

eth0VpnPort		1.3.6.1.4.1.24350.6.9.4
port number at vpn server
Status: current	Access: read-write
OBJECT-TYPE
	INTEGER

eth0VpnProtocol		1.3.6.1.4.1.24350.6.9.5
protocol used for vpn
Status: current	Access: read-write
OBJECT-TYPE
	OCTET STRING

eth0VpnServer		1.3.6.1.4.1.24350.6.9.6
hostname or ip address of the vpn server
Status: current	Access: read-write
OBJECT-TYPE
	OCTET STRING

br0		1.3.6.1.4.1.24350.7
OBJECT IDENTIFIER

br0Acl		1.3.6.1.4.1.24350.7.1
OBJECT IDENTIFIER

br0AclMode		1.3.6.1.4.1.24350.7.1.1
access control list mode ( 'none', 'whitelist', 'blacklist' )
Status: current	Access: read-write
OBJECT-TYPE
	OCTET STRING

br0Dhcp		1.3.6.1.4.1.24350.7.2
OBJECT IDENTIFIER

br0DhcpAlwaysbroadcast		1.3.6.1.4.1.24350.7.2.1
always broadcast dhcp responses
Status: current	Access: read-write
OBJECT-TYPE
	OCTET STRING

br0DhcpDefaultleasetime		1.3.6.1.4.1.24350.7.2.2
default dhcp lease expiration in seconds
Status: current	Access: read-write
OBJECT-TYPE
	INTEGER

br0DhcpMaxleasetime		1.3.6.1.4.1.24350.7.2.3
maximum requestable dhcp lease expiration in seconds
Status: current	Access: read-write
OBJECT-TYPE
	INTEGER

br0DhcpRelay		1.3.6.1.4.1.24350.7.2.4
OBJECT IDENTIFIER

br0DhcpRelayEnable		1.3.6.1.4.1.24350.7.2.4.1
use dhcp relay (if sys.dhcp.relay.enable=yes)
Status: current	Access: read-write
OBJECT-TYPE
	OCTET STRING

br0DhcpReserve		1.3.6.1.4.1.24350.7.2.5
ip addresses to reserve at bottom of range for static assignments
Status: current	Access: read-write
OBJECT-TYPE
	INTEGER

br0DhcpRole		1.3.6.1.4.1.24350.7.2.6
interface dhcp role (none, client, server)
Status: current	Access: read-write
OBJECT-TYPE
	OCTET STRING

br0Enable		1.3.6.1.4.1.24350.7.3
interface is enabled
Status: current	Access: read-write
OBJECT-TYPE
	OCTET STRING

br0Forwardingdelay		1.3.6.1.4.1.24350.7.4
how long bridge watches traffic before participating
Status: current	Access: read-write
OBJECT-TYPE
	INTEGER

br0If		1.3.6.1.4.1.24350.7.5
interface associated with this module
Status: current	Access: read-only
OBJECT-TYPE
	OCTET STRING

br0Ip		1.3.6.1.4.1.24350.7.6
OBJECT IDENTIFIER

br0IpAddress		1.3.6.1.4.1.24350.7.6.1
ip address
Status: current	Access: read-only
OBJECT-TYPE
	OCTET STRING

br0IpAddressforce		1.3.6.1.4.1.24350.7.6.2
override .ip.address (or blank)
Status: current	Access: read-write
OBJECT-TYPE
	OCTET STRING

br0IpBroadcast		1.3.6.1.4.1.24350.7.6.3
broadcast address
Status: current	Access: read-only
OBJECT-TYPE
	OCTET STRING

br0IpBroadcastforce		1.3.6.1.4.1.24350.7.6.4
override .ip.broadcast (or blank)
Status: current	Access: read-write
OBJECT-TYPE
	OCTET STRING

br0IpGateway		1.3.6.1.4.1.24350.7.6.5
gateway address
Status: current	Access: read-only
OBJECT-TYPE
	OCTET STRING

br0IpGatewayforce		1.3.6.1.4.1.24350.7.6.6
override .ip.gateway (or blank)
Status: current	Access: read-write
OBJECT-TYPE
	OCTET STRING

br0IpNetmask		1.3.6.1.4.1.24350.7.6.7
network mask
Status: current	Access: read-only
OBJECT-TYPE
	OCTET STRING

br0IpNetmaskforce		1.3.6.1.4.1.24350.7.6.8
override .ip.netmask (or blank)
Status: current	Access: read-write
OBJECT-TYPE
	OCTET STRING

br0Role		1.3.6.1.4.1.24350.7.7
intended interface role (bridge)
Status: current	Access: read-only
OBJECT-TYPE
	OCTET STRING

br0Routes		1.3.6.1.4.1.24350.7.8
OBJECT IDENTIFIER

br0RoutesStatic		1.3.6.1.4.1.24350.7.8.1
static routes for this interface
Status: current	Access: read-write
OBJECT-TYPE
	OCTET STRING

br0Stp		1.3.6.1.4.1.24350.7.9
OBJECT IDENTIFIER

br0StpEnable		1.3.6.1.4.1.24350.7.9.1
enable spanning tree protocol
Status: current	Access: read-write
OBJECT-TYPE
	OCTET STRING

alias99		1.3.6.1.4.1.24350.8
OBJECT IDENTIFIER

alias99If		1.3.6.1.4.1.24350.8.1
interface associated with this module
Status: current	Access: read-only
OBJECT-TYPE
	OCTET STRING

alias99Ip		1.3.6.1.4.1.24350.8.2
OBJECT IDENTIFIER

alias99IpAddress		1.3.6.1.4.1.24350.8.2.1
ip address
Status: current	Access: read-write
OBJECT-TYPE
	OCTET STRING

alias99IpBroadcast		1.3.6.1.4.1.24350.8.2.2
broadcast address
Status: current	Access: read-write
OBJECT-TYPE
	OCTET STRING

alias99IpGateway		1.3.6.1.4.1.24350.8.2.3
gateway address
Status: current	Access: read-write
OBJECT-TYPE
	OCTET STRING

alias99IpNetmask		1.3.6.1.4.1.24350.8.2.4
network mask
Status: current	Access: read-write
OBJECT-TYPE
	OCTET STRING

radio0		1.3.6.1.4.1.24350.9
OBJECT IDENTIFIER

radio0Channel		1.3.6.1.4.1.24350.9.1
wireless channel
Status: current	Access: read-write
OBJECT-TYPE
	INTEGER

radio0Chansize		1.3.6.1.4.1.24350.9.2
wireless channel size - 1=full, 2=half, 4=quarter
Status: current	Access: read-write
OBJECT-TYPE
	OCTET STRING

radio0Distance		1.3.6.1.4.1.24350.9.3
distance (in miles or km, see sys.units) of maximum link distance, or blank
Status: current	Access: read-write
OBJECT-TYPE
	OCTET STRING

radio0Distancemeters		1.3.6.1.4.1.24350.9.4
distance in meters
Status: current	Access: read-write
OBJECT-TYPE
	OCTET STRING

radio0Frequency		1.3.6.1.4.1.24350.9.5
wireless frequency (overrides radio0.channel)
Status: current	Access: read-write
OBJECT-TYPE
	OCTET STRING

radio0Mode		1.3.6.1.4.1.24350.9.6
802.11 mode (0=auto, 1=802.11a, 2=802.11b, 3=802.11g)
Status: current	Access: read-write
OBJECT-TYPE
	INTEGER

radio0Modes		1.3.6.1.4.1.24350.9.7
802.11 modes supported by this card
Status: current	Access: read-only
OBJECT-TYPE
	OCTET STRING

radio0Pureg		1.3.6.1.4.1.24350.9.8
802.11g only mode (no 802.11b)
Status: current	Access: read-write
OBJECT-TYPE
	OCTET STRING

radio0Ratectl		1.3.6.1.4.1.24350.9.9
rate control algorithm (sample, minstrel)
Status: current	Access: read-write
OBJECT-TYPE
	OCTET STRING

radio0Rts		1.3.6.1.4.1.24350.9.10
rts threshold
Status: current	Access: read-write
OBJECT-TYPE
	OCTET STRING

radio0Shortpreamble		1.3.6.1.4.1.24350.9.11
allow short preamble - buggy old clients may need this off
Status: current	Access: read-write
OBJECT-TYPE
	OCTET STRING

radio0Turbo		1.3.6.1.4.1.24350.9.12
802.11g turbo mode
Status: current	Access: read-write
OBJECT-TYPE
	OCTET STRING

radio0Txpower		1.3.6.1.4.1.24350.9.13
max transmit power in dBm (0-30)
Status: current	Access: read-write
OBJECT-TYPE
	OCTET STRING

radio0Wlans		1.3.6.1.4.1.24350.9.14
wlans mapped to this radio
Status: current	Access: read-only
OBJECT-TYPE
	OCTET STRING

radio0Wlansextra		1.3.6.1.4.1.24350.9.15
Tok_String
Status: current	Access: read-only
OBJECT-TYPE
	OCTET STRING

radio1		1.3.6.1.4.1.24350.10
OBJECT IDENTIFIER

radio1Channel		1.3.6.1.4.1.24350.10.1
wireless channel
Status: current	Access: read-write
OBJECT-TYPE
	INTEGER

radio1Chansize		1.3.6.1.4.1.24350.10.2
wireless channel size - 1=full, 2=half, 4=quarter
Status: current	Access: read-write
OBJECT-TYPE
	OCTET STRING

radio1Distance		1.3.6.1.4.1.24350.10.3
distance (in miles or km, see sys.units) of maximum link distance, or blank
Status: current	Access: read-write
OBJECT-TYPE
	OCTET STRING

radio1Distancemeters		1.3.6.1.4.1.24350.10.4
distance in meters
Status: current	Access: read-write
OBJECT-TYPE
	OCTET STRING

radio1Frequency		1.3.6.1.4.1.24350.10.5
wireless frequency (overrides radio1.channel)
Status: current	Access: read-write
OBJECT-TYPE
	OCTET STRING

radio1Mode		1.3.6.1.4.1.24350.10.6
802.11 mode (0=auto, 1=802.11a, 2=802.11b, 3=802.11g)
Status: current	Access: read-write
OBJECT-TYPE
	INTEGER

radio1Modes		1.3.6.1.4.1.24350.10.7
802.11 modes supported by this card
Status: current	Access: read-only
OBJECT-TYPE
	OCTET STRING

radio1Pureg		1.3.6.1.4.1.24350.10.8
802.11g only mode (no 802.11b)
Status: current	Access: read-write
OBJECT-TYPE
	OCTET STRING

radio1Ratectl		1.3.6.1.4.1.24350.10.9
rate control algorithm (sample, minstrel)
Status: current	Access: read-write
OBJECT-TYPE
	OCTET STRING

radio1Rts		1.3.6.1.4.1.24350.10.10
rts threshold
Status: current	Access: read-write
OBJECT-TYPE
	OCTET STRING

radio1Shortpreamble		1.3.6.1.4.1.24350.10.11
allow short preamble - buggy old clients may need this off
Status: current	Access: read-write
OBJECT-TYPE
	OCTET STRING

radio1Turbo		1.3.6.1.4.1.24350.10.12
802.11g turbo mode
Status: current	Access: read-write
OBJECT-TYPE
	OCTET STRING

radio1Txpower		1.3.6.1.4.1.24350.10.13
max transmit power in dBm (0-30)
Status: current	Access: read-write
OBJECT-TYPE
	OCTET STRING

radio1Wlans		1.3.6.1.4.1.24350.10.14
wlans mapped to this radio
Status: current	Access: read-only
OBJECT-TYPE
	OCTET STRING

radio1Wlansextra		1.3.6.1.4.1.24350.10.15
Tok_String
Status: current	Access: read-only
OBJECT-TYPE
	OCTET STRING

wlan0		1.3.6.1.4.1.24350.11
OBJECT IDENTIFIER

wlan0Acl		1.3.6.1.4.1.24350.11.1
OBJECT IDENTIFIER

wlan0AclMode		1.3.6.1.4.1.24350.11.1.1
access control list mode ( 'none', 'whitelist', 'blacklist' )
Status: current	Access: read-write
OBJECT-TYPE
	OCTET STRING

wlan0Beaconinterval		1.3.6.1.4.1.24350.11.2
beacon interval in milliseconds
Status: current	Access: read-write
OBJECT-TYPE
	INTEGER

wlan0Cellid		1.3.6.1.4.1.24350.11.3
adhoc cell id
Status: current	Access: read-only
OBJECT-TYPE
	OCTET STRING

wlan0Dhcp		1.3.6.1.4.1.24350.11.4
OBJECT IDENTIFIER

wlan0DhcpAlwaysbroadcast		1.3.6.1.4.1.24350.11.4.1
always broadcast dhcp responses
Status: current	Access: read-write
OBJECT-TYPE
	OCTET STRING

wlan0DhcpDefaultleasetime		1.3.6.1.4.1.24350.11.4.2
default dhcp lease expiration in seconds
Status: current	Access: read-write
OBJECT-TYPE
	INTEGER

wlan0DhcpMaxleasetime		1.3.6.1.4.1.24350.11.4.3
maximum requestable dhcp lease expiration in seconds
Status: current	Access: read-write
OBJECT-TYPE
	INTEGER

wlan0DhcpRelay		1.3.6.1.4.1.24350.11.4.4
OBJECT IDENTIFIER

wlan0DhcpRelayEnable		1.3.6.1.4.1.24350.11.4.4.1
use dhcp relay (if sys.dhcp.relay.enable=yes)
Status: current	Access: read-write
OBJECT-TYPE
	OCTET STRING

wlan0DhcpReserve		1.3.6.1.4.1.24350.11.4.5
ip addresses to reserve at bottom of range for static assignments
Status: current	Access: read-write
OBJECT-TYPE
	INTEGER

wlan0DhcpRole		1.3.6.1.4.1.24350.11.4.6
interface dhcp role (none, client, server)
Status: current	Access: read-write
OBJECT-TYPE
	OCTET STRING

wlan0Enable		1.3.6.1.4.1.24350.11.5
interface is enabled
Status: current	Access: read-write
OBJECT-TYPE
	OCTET STRING

wlan0Enhsec		1.3.6.1.4.1.24350.11.6
ignore clients that specify 'ANY' ssid
Status: current	Access: read-write
OBJECT-TYPE
	OCTET STRING

wlan0Essid		1.3.6.1.4.1.24350.11.7
essid for this ap
Status: current	Access: read-write
OBJECT-TYPE
	OCTET STRING

wlan0Fabric		1.3.6.1.4.1.24350.11.8
OBJECT IDENTIFIER

wlan0FabricArgs		1.3.6.1.4.1.24350.11.8.1
mesh fabric arguments - touch at your peril!
Status: current	Access: read-write
OBJECT-TYPE
	OCTET STRING

wlan0FabricBridge		1.3.6.1.4.1.24350.11.8.2
bridge argument
Status: current	Access: read-write
OBJECT-TYPE
	OCTET STRING

wlan0FabricCmd1		1.3.6.1.4.1.24350.11.8.3
command to activate mesh fabric part 1
Status: current	Access: read-write
OBJECT-TYPE
	OCTET STRING

wlan0FabricCmd2		1.3.6.1.4.1.24350.11.8.4
command to activate mesh part 2
Status: current	Access: read-write
OBJECT-TYPE
	OCTET STRING

wlan0FabricEnable		1.3.6.1.4.1.24350.11.8.5
run mesh fabric?
Status: current	Access: read-write
OBJECT-TYPE
	OCTET STRING

wlan0FabricGateway		1.3.6.1.4.1.24350.11.8.6
OBJECT IDENTIFIER

wlan0FabricGatewayEnable		1.3.6.1.4.1.24350.11.8.6.1
is this node a gateway
Status: current	Access: read-only
OBJECT-TYPE
	OCTET STRING

wlan0FabricGatewayIf		1.3.6.1.4.1.24350.11.8.6.2
interface acting as mesh gateway, if any
Status: current	Access: read-only
OBJECT-TYPE
	OCTET STRING

wlan0FabricMargin		1.3.6.1.4.1.24350.11.8.7
if rssi drops this far below .join, drop the neighbor
Status: current	Access: read-write
OBJECT-TYPE
	INTEGER

wlan0FabricRouteadvert		1.3.6.1.4.1.24350.11.8.8
route advertisement arguments
Status: current	Access: read-write
OBJECT-TYPE
	OCTET STRING

wlan0FabricRssi		1.3.6.1.4.1.24350.11.8.9
OBJECT IDENTIFIER

wlan0FabricRssiJoin		1.3.6.1.4.1.24350.11.8.9.1
rssi level to join neighbor
Status: current	Access: read-write
OBJECT-TYPE
	INTEGER

wlan0FabricRssiMargin		1.3.6.1.4.1.24350.11.8.9.2
if rssi drops this far below .join, drop neighbor
Status: current	Access: read-write
OBJECT-TYPE
	INTEGER

wlan0Frag		1.3.6.1.4.1.24350.11.9
fragmentation threshold
Status: current	Access: read-write
OBJECT-TYPE
	OCTET STRING

wlan0Hideessid		1.3.6.1.4.1.24350.11.10
don't broadcast the essid
Status: current	Access: read-write
OBJECT-TYPE
	OCTET STRING

wlan0If		1.3.6.1.4.1.24350.11.11
interface associated with this module
Status: current	Access: read-only
OBJECT-TYPE
	OCTET STRING

wlan0Ip		1.3.6.1.4.1.24350.11.12
OBJECT IDENTIFIER

wlan0IpAddress		1.3.6.1.4.1.24350.11.12.1
ip address
Status: current	Access: read-only
OBJECT-TYPE
	OCTET STRING

wlan0IpAddressforce		1.3.6.1.4.1.24350.11.12.2
override .ip.address (or blank)
Status: current	Access: read-only
OBJECT-TYPE
	OCTET STRING

wlan0IpBroadcast		1.3.6.1.4.1.24350.11.12.3
broadcast address
Status: current	Access: read-only
OBJECT-TYPE
	OCTET STRING

wlan0IpBroadcastforce		1.3.6.1.4.1.24350.11.12.4
override .ip.broadcast (or blank)
Status: current	Access: read-only
OBJECT-TYPE
	OCTET STRING

wlan0IpGateway		1.3.6.1.4.1.24350.11.12.5
gateway address
Status: current	Access: read-only
OBJECT-TYPE
	OCTET STRING

wlan0IpGatewayforce		1.3.6.1.4.1.24350.11.12.6
override .ip.gateway (or blank)
Status: current	Access: read-only
OBJECT-TYPE
	OCTET STRING

wlan0IpNetmask		1.3.6.1.4.1.24350.11.12.7
network mask
Status: current	Access: read-write
OBJECT-TYPE
	OCTET STRING

wlan0IpNetmaskforce		1.3.6.1.4.1.24350.11.12.8
override .ip.netmask (or blank)
Status: current	Access: read-only
OBJECT-TYPE
	OCTET STRING

wlan0Iwconfig		1.3.6.1.4.1.24350.11.13
OBJECT IDENTIFIER

wlan0IwconfigCmd		1.3.6.1.4.1.24350.11.13.1
parameters to pass to iwconfig after all other settings
Status: current	Access: read-write
OBJECT-TYPE
	OCTET STRING

wlan0Iwpriv		1.3.6.1.4.1.24350.11.14
OBJECT IDENTIFIER

wlan0IwprivCmd		1.3.6.1.4.1.24350.11.14.1
parameters to pass to iwpriv after all other settings
Status: current	Access: read-write
OBJECT-TYPE
	OCTET STRING

wlan0Key		1.3.6.1.4.1.24350.11.15
wep key - if present, overrides .keys
Status: current	Access: read-write
OBJECT-TYPE
	OCTET STRING

wlan0Keys		1.3.6.1.4.1.24350.11.16
OBJECT IDENTIFIER

wlan0Keys1		1.3.6.1.4.1.24350.11.16.1
one of four keys selected with .keys.default
Status: current	Access: read-write
OBJECT-TYPE
	OCTET STRING

wlan0Keys2		1.3.6.1.4.1.24350.11.16.2
one of four keys selected with .keys.default
Status: current	Access: read-write
OBJECT-TYPE
	OCTET STRING

wlan0Keys3		1.3.6.1.4.1.24350.11.16.3
one of four keys selected with .keys.default
Status: current	Access: read-write
OBJECT-TYPE
	OCTET STRING

wlan0Keys4		1.3.6.1.4.1.24350.11.16.4
one of four keys selected with .keys.default
Status: current	Access: read-write
OBJECT-TYPE
	OCTET STRING

wlan0KeysDefault		1.3.6.1.4.1.24350.11.16.5
1 to 4 to choose which of wlan0.keys.1-4 to use
Status: current	Access: read-write
OBJECT-TYPE
	OCTET STRING

wlan0Mconfd		1.3.6.1.4.1.24350.11.17
OBJECT IDENTIFIER

wlan0MconfdEnable		1.3.6.1.4.1.24350.11.17.1
run mconfd daemon? distributed mesh configuration
Status: current	Access: read-write
OBJECT-TYPE
	OCTET STRING

wlan0MconfdExternalhosts		1.3.6.1.4.1.24350.11.17.2
list of external hosts we try to make external
Status: current	Access: read-only
OBJECT-TYPE
	OCTET STRING

wlan0Mode		1.3.6.1.4.1.24350.11.18
operating mode ( ap/master, adhoc, adhoc-demo, sta/client )
Status: current	Access: read-write
OBJECT-TYPE
	OCTET STRING

wlan0Mroute		1.3.6.1.4.1.24350.11.19
OBJECT IDENTIFIER

wlan0MrouteArgs		1.3.6.1.4.1.24350.11.19.1
mroute arguments
Status: current	Access: read-write
OBJECT-TYPE
	OCTET STRING

wlan0MrouteCmd		1.3.6.1.4.1.24350.11.19.2
mroute command
Status: current	Access: read-write
OBJECT-TYPE
	OCTET STRING

wlan0MrouteEnable		1.3.6.1.4.1.24350.11.19.3
run mroute daemon - IGMP query utility
Status: current	Access: read-write
OBJECT-TYPE
	OCTET STRING

wlan0Mtu		1.3.6.1.4.1.24350.11.20
maximum transmission unit - may cause serious problems if set too low
Status: current	Access: read-write
OBJECT-TYPE
	INTEGER

wlan0Radio		1.3.6.1.4.1.24350.11.21
which physical radio this vap is on (0 or 1)
Status: current	Access: read-write
OBJECT-TYPE
	OCTET STRING

wlan0Rate		1.3.6.1.4.1.24350.11.22
communications rate
Status: current	Access: read-write
OBJECT-TYPE
	OCTET STRING

wlan0Role		1.3.6.1.4.1.24350.11.23
intended interface role (mesh, pxp (point to point), bridge)
Status: current	Access: read-write
OBJECT-TYPE
	OCTET STRING

wlan0Routes		1.3.6.1.4.1.24350.11.24
OBJECT IDENTIFIER

wlan0RoutesAddprivnets		1.3.6.1.4.1.24350.11.24.1
add sys.nets.internal.combined to mesh static routes?
Status: current	Access: read-write
OBJECT-TYPE
	OCTET STRING

wlan0RoutesStatic		1.3.6.1.4.1.24350.11.24.2
static routes for this interface
Status: current	Access: read-write
OBJECT-TYPE
	OCTET STRING

wlan0Topomc		1.3.6.1.4.1.24350.11.25
OBJECT IDENTIFIER

wlan0TopomcArgs		1.3.6.1.4.1.24350.11.25.1
topomc arguments
Status: current	Access: read-write
OBJECT-TYPE
	OCTET STRING

wlan0TopomcCmd		1.3.6.1.4.1.24350.11.25.2
topomc command
Status: current	Access: read-write
OBJECT-TYPE
	OCTET STRING

wlan0TopomcEnable		1.3.6.1.4.1.24350.11.25.3
run topomc daemon? - network topology reporting
Status: current	Access: read-write
OBJECT-TYPE
	OCTET STRING

wlan1		1.3.6.1.4.1.24350.12
OBJECT IDENTIFIER

wlan1Acl		1.3.6.1.4.1.24350.12.1
OBJECT IDENTIFIER

wlan1AclMode		1.3.6.1.4.1.24350.12.1.1
access control list mode ( 'none', 'whitelist', 'blacklist' )
Status: current	Access: read-write
OBJECT-TYPE
	OCTET STRING

wlan1Beaconinterval		1.3.6.1.4.1.24350.12.2
beacon interval in milliseconds
Status: current	Access: read-write
OBJECT-TYPE
	INTEGER

wlan1Cellid		1.3.6.1.4.1.24350.12.3
cell id for adhoc mode
Status: current	Access: read-write
OBJECT-TYPE
	OCTET STRING

wlan1Dhcp		1.3.6.1.4.1.24350.12.4
OBJECT IDENTIFIER

wlan1DhcpAlwaysbroadcast		1.3.6.1.4.1.24350.12.4.1
always broadcast dhcp responses
Status: current	Access: read-write
OBJECT-TYPE
	OCTET STRING

wlan1DhcpDefaultleasetime		1.3.6.1.4.1.24350.12.4.2
default dhcp lease expiration in seconds
Status: current	Access: read-write
OBJECT-TYPE
	INTEGER

wlan1DhcpMaxleasetime		1.3.6.1.4.1.24350.12.4.3
maximum requestable dhcp lease expiration in seconds
Status: current	Access: read-write
OBJECT-TYPE
	INTEGER

wlan1DhcpRelay		1.3.6.1.4.1.24350.12.4.4
OBJECT IDENTIFIER

wlan1DhcpRelayEnable		1.3.6.1.4.1.24350.12.4.4.1
use dhcp relay (if sys.dhcp.relay.enable=yes)
Status: current	Access: read-write
OBJECT-TYPE
	OCTET STRING

wlan1DhcpReserve		1.3.6.1.4.1.24350.12.4.5
ip addresses to reserve at bottom of range for static assignments
Status: current	Access: read-write
OBJECT-TYPE
	INTEGER

wlan1DhcpRole		1.3.6.1.4.1.24350.12.4.6
interface dhcp role (none, client, server)
Status: current	Access: read-write
OBJECT-TYPE
	OCTET STRING

wlan1Enable		1.3.6.1.4.1.24350.12.5
interface is enabled
Status: current	Access: read-write
OBJECT-TYPE
	OCTET STRING

wlan1Enhsec		1.3.6.1.4.1.24350.12.6
ignore clients that specify 'ANY' ssid
Status: current	Access: read-write
OBJECT-TYPE
	OCTET STRING

wlan1Essid		1.3.6.1.4.1.24350.12.7
essid for this ap
Status: current	Access: read-write
OBJECT-TYPE
	OCTET STRING

wlan1Frag		1.3.6.1.4.1.24350.12.8
fragmentation threshold
Status: current	Access: read-write
OBJECT-TYPE
	OCTET STRING

wlan1Hideessid		1.3.6.1.4.1.24350.12.9
don't broadcast the essid
Status: current	Access: read-write
OBJECT-TYPE
	OCTET STRING

wlan1If		1.3.6.1.4.1.24350.12.10
interface associated with this module
Status: current	Access: read-only
OBJECT-TYPE
	OCTET STRING

wlan1Ip		1.3.6.1.4.1.24350.12.11
OBJECT IDENTIFIER

wlan1IpAddress		1.3.6.1.4.1.24350.12.11.1
ip address
Status: current	Access: read-only
OBJECT-TYPE
	OCTET STRING

wlan1IpAddressforce		1.3.6.1.4.1.24350.12.11.2
override .ip.address (or blank)
Status: current	Access: read-write
OBJECT-TYPE
	OCTET STRING

wlan1IpBroadcast		1.3.6.1.4.1.24350.12.11.3
broadcast address
Status: current	Access: read-only
OBJECT-TYPE
	OCTET STRING

wlan1IpBroadcastforce		1.3.6.1.4.1.24350.12.11.4
override .ip.broadcast (or blank)
Status: current	Access: read-write
OBJECT-TYPE
	OCTET STRING

wlan1IpGateway		1.3.6.1.4.1.24350.12.11.5
gateway address
Status: current	Access: read-only
OBJECT-TYPE
	OCTET STRING

wlan1IpGatewayforce		1.3.6.1.4.1.24350.12.11.6
override .ip.gateway (or blank)
Status: current	Access: read-write
OBJECT-TYPE
	OCTET STRING

wlan1IpImplicit		1.3.6.1.4.1.24350.12.11.7
OBJECT IDENTIFIER

wlan1IpImplicitSize		1.3.6.1.4.1.24350.12.11.7.1
OBJECT IDENTIFIER

wlan1IpImplicitSizeActual		1.3.6.1.4.1.24350.12.11.7.1.1
actual size of assigned address range
Status: current	Access: read-only
OBJECT-TYPE
	INTEGER

wlan1IpImplicitSizeRequested		1.3.6.1.4.1.24350.12.11.7.1.2
requested size of address range (multiple of 32 minus 1)
Status: current	Access: read-write
OBJECT-TYPE
	OCTET STRING

wlan1IpImplicitStart		1.3.6.1.4.1.24350.12.11.7.2
OBJECT IDENTIFIER

wlan1IpImplicitStartActual		1.3.6.1.4.1.24350.12.11.7.2.1
actual assigned fourth octet
Status: current	Access: read-only
OBJECT-TYPE
	INTEGER

wlan1IpImplicitStartRequested		1.3.6.1.4.1.24350.12.11.7.2.2
requested interface fourth octet (multiple of 32 plus 1)
Status: current	Access: read-write
OBJECT-TYPE
	OCTET STRING

wlan1IpNetmask		1.3.6.1.4.1.24350.12.11.8
network mask
Status: current	Access: read-only
OBJECT-TYPE
	OCTET STRING

wlan1IpNetmaskforce		1.3.6.1.4.1.24350.12.11.9
override .ip.netmask (or blank)
Status: current	Access: read-write
OBJECT-TYPE
	OCTET STRING

wlan1Iwconfig		1.3.6.1.4.1.24350.12.12
OBJECT IDENTIFIER

wlan1IwconfigCmd		1.3.6.1.4.1.24350.12.12.1
parameters to pass to iwconfig after all other settings
Status: current	Access: read-write
OBJECT-TYPE
	OCTET STRING

wlan1Iwpriv		1.3.6.1.4.1.24350.12.13
OBJECT IDENTIFIER

wlan1IwprivCmd		1.3.6.1.4.1.24350.12.13.1
parameters to pass to iwpriv after all other settings
Status: current	Access: read-write
OBJECT-TYPE
	OCTET STRING

wlan1Key		1.3.6.1.4.1.24350.12.14
wep key - if present, overrides .keys
Status: current	Access: read-write
OBJECT-TYPE
	OCTET STRING

wlan1Keys		1.3.6.1.4.1.24350.12.15
OBJECT IDENTIFIER

wlan1Keys1		1.3.6.1.4.1.24350.12.15.1
one of four keys selected with .keys.default
Status: current	Access: read-write
OBJECT-TYPE
	OCTET STRING

wlan1Keys2		1.3.6.1.4.1.24350.12.15.2
one of four keys selected with .keys.default
Status: current	Access: read-write
OBJECT-TYPE
	OCTET STRING

wlan1Keys3		1.3.6.1.4.1.24350.12.15.3
one of four keys selected with .keys.default
Status: current	Access: read-write
OBJECT-TYPE
	OCTET STRING

wlan1Keys4		1.3.6.1.4.1.24350.12.15.4
one of four keys selected with .keys.default
Status: current	Access: read-write
OBJECT-TYPE
	OCTET STRING

wlan1KeysDefault		1.3.6.1.4.1.24350.12.15.5
1 to 4 to choose which of wlan1.keys.1-4 to use
Status: current	Access: read-write
OBJECT-TYPE
	OCTET STRING

wlan1Mode		1.3.6.1.4.1.24350.12.16
operating mode ( ap/master, adhoc, adhoc-demo, sta/client )
Status: current	Access: read-write
OBJECT-TYPE
	OCTET STRING

wlan1Mtu		1.3.6.1.4.1.24350.12.17
maximum transmission unit - may cause serious problems if set too low
Status: current	Access: read-write
OBJECT-TYPE
	INTEGER

wlan1Radio		1.3.6.1.4.1.24350.12.18
which physical radio this vap is on (0 or 1)
Status: current	Access: read-write
OBJECT-TYPE
	OCTET STRING

wlan1Rate		1.3.6.1.4.1.24350.12.19
communications rate
Status: current	Access: read-write
OBJECT-TYPE
	OCTET STRING

wlan1Role		1.3.6.1.4.1.24350.12.20
intended interface role (access, bridge)
Status: current	Access: read-write
OBJECT-TYPE
	OCTET STRING

wlan1Routes		1.3.6.1.4.1.24350.12.21
OBJECT IDENTIFIER

wlan1RoutesStatic		1.3.6.1.4.1.24350.12.21.1
static routes for this interface
Status: current	Access: read-write
OBJECT-TYPE
	OCTET STRING

wlan1Vlan		1.3.6.1.4.1.24350.12.22
OBJECT IDENTIFIER

wlan1VlanEnable		1.3.6.1.4.1.24350.12.22.1
use a vlan for this interface
Status: current	Access: read-write
OBJECT-TYPE
	OCTET STRING

wlan1VlanId		1.3.6.1.4.1.24350.12.22.2
vlan id (0 and 1 are usually reserved)
Status: current	Access: read-write
OBJECT-TYPE
	INTEGER

wlan1Wpa		1.3.6.1.4.1.24350.12.23
OBJECT IDENTIFIER

wlan1WpaAuth		1.3.6.1.4.1.24350.12.23.1
OBJECT IDENTIFIER

wlan1WpaAuthArgs		1.3.6.1.4.1.24350.12.23.1.1
arguments passed to authenticator
Status: current	Access: read-write
OBJECT-TYPE
	OCTET STRING

wlan1WpaAuthCustom		1.3.6.1.4.1.24350.12.23.1.2
command used to start authenticator if .wpa.auth.type is 'custom'
Status: current	Access: read-write
OBJECT-TYPE
	OCTET STRING

wlan1WpaAuthInternal		1.3.6.1.4.1.24350.12.23.1.3
0 for external, 1 for internal
Status: current	Access: read-write
OBJECT-TYPE
	OCTET STRING

wlan1WpaAuthServer		1.3.6.1.4.1.24350.12.23.1.4
OBJECT IDENTIFIER

wlan1WpaAuthServerAddr		1.3.6.1.4.1.24350.12.23.1.4.1
authentication server address
Status: current	Access: read-write
OBJECT-TYPE
	OCTET STRING

wlan1WpaAuthServerPort		1.3.6.1.4.1.24350.12.23.1.4.2
authentication server port
Status: current	Access: read-write
OBJECT-TYPE
	INTEGER

wlan1WpaAuthServerSharedsecret		1.3.6.1.4.1.24350.12.23.1.4.3
shared secret
Status: current	Access: read-write
OBJECT-TYPE
	OCTET STRING

wlan1WpaAuthType		1.3.6.1.4.1.24350.12.23.1.5
'hostapd' or 'custom'
Status: current	Access: read-write
OBJECT-TYPE
	OCTET STRING

wlan1WpaBridge		1.3.6.1.4.1.24350.12.23.2
bridge if any, set by sys.l2.bridge.enable
Status: current	Access: read-only
OBJECT-TYPE
	OCTET STRING

wlan1WpaCa		1.3.6.1.4.1.24350.12.23.3
OBJECT IDENTIFIER

wlan1WpaCaCert		1.3.6.1.4.1.24350.12.23.3.1
OBJECT IDENTIFIER

wlan1WpaCaCertFile		1.3.6.1.4.1.24350.12.23.3.1.1
ca_cert file
Status: current	Access: read-write
OBJECT-TYPE
	OCTET STRING

wlan1WpaEapol		1.3.6.1.4.1.24350.12.23.4
OBJECT IDENTIFIER

wlan1WpaEapolVersion		1.3.6.1.4.1.24350.12.23.4.1
2 is default, but some older clients need 1
Status: current	Access: read-write
OBJECT-TYPE
	OCTET STRING

wlan1WpaEnable		1.3.6.1.4.1.24350.12.23.5
wpa support enabled?
Status: current	Access: read-write
OBJECT-TYPE
	OCTET STRING

wlan1WpaEssid		1.3.6.1.4.1.24350.12.23.6
essid for wpa authentication
Status: current	Access: read-write
OBJECT-TYPE
	OCTET STRING

wlan1WpaIf		1.3.6.1.4.1.24350.12.23.7
management frame interface, same as wlan1.if
Status: current	Access: read-only
OBJECT-TYPE
	OCTET STRING

wlan1WpaKeymgmt		1.3.6.1.4.1.24350.12.23.8
WPA-PSK and/or WPA-EAP
Status: current	Access: read-write
OBJECT-TYPE
	OCTET STRING

wlan1WpaMode		1.3.6.1.4.1.24350.12.23.9
wpa modes: 1=wpa1, 2=wpa2, 3=both
Status: current	Access: read-write
OBJECT-TYPE
	INTEGER

wlan1WpaNode		1.3.6.1.4.1.24350.12.23.10
OBJECT IDENTIFIER

wlan1WpaNodeCert		1.3.6.1.4.1.24350.12.23.10.1
OBJECT IDENTIFIER

wlan1WpaNodeCertFile		1.3.6.1.4.1.24350.12.23.10.1.1
server_cert file
Status: current	Access: read-write
OBJECT-TYPE
	OCTET STRING

wlan1WpaNodeKey		1.3.6.1.4.1.24350.12.23.10.2
OBJECT IDENTIFIER

wlan1WpaNodeKeyFile		1.3.6.1.4.1.24350.12.23.10.2.1
private_key file
Status: current	Access: read-write
OBJECT-TYPE
	OCTET STRING

wlan1WpaNodeKeyPassphrase		1.3.6.1.4.1.24350.12.23.10.2.2
passphrase for the node's private key
Status: current	Access: read-write
OBJECT-TYPE
	OCTET STRING

wlan1WpaPairwise		1.3.6.1.4.1.24350.12.23.11
accepted cipher suites - CCMP and/or TKIP
Status: current	Access: read-write
OBJECT-TYPE
	OCTET STRING

wlan1WpaPassphrase		1.3.6.1.4.1.24350.12.23.12
wpa passphrase
Status: current	Access: read-write
OBJECT-TYPE
	OCTET STRING

wlan2		1.3.6.1.4.1.24350.13
OBJECT IDENTIFIER

wlan2Acl		1.3.6.1.4.1.24350.13.1
OBJECT IDENTIFIER

wlan2AclMode		1.3.6.1.4.1.24350.13.1.1
access control list mode ( 'none', 'whitelist', 'blacklist' )
Status: current	Access: read-write
OBJECT-TYPE
	OCTET STRING

wlan2Beaconinterval		1.3.6.1.4.1.24350.13.2
beacon interval in milliseconds
Status: current	Access: read-write
OBJECT-TYPE
	INTEGER

wlan2Cellid		1.3.6.1.4.1.24350.13.3
cell id for adhoc mode
Status: current	Access: read-write
OBJECT-TYPE
	OCTET STRING

wlan2Dhcp		1.3.6.1.4.1.24350.13.4
OBJECT IDENTIFIER

wlan2DhcpAlwaysbroadcast		1.3.6.1.4.1.24350.13.4.1
always broadcast dhcp responses
Status: current	Access: read-write
OBJECT-TYPE
	OCTET STRING

wlan2DhcpDefaultleasetime		1.3.6.1.4.1.24350.13.4.2
default dhcp lease expiration in seconds
Status: current	Access: read-write
OBJECT-TYPE
	INTEGER

wlan2DhcpMaxleasetime		1.3.6.1.4.1.24350.13.4.3
maximum requestable dhcp lease expiration in seconds
Status: current	Access: read-write
OBJECT-TYPE
	INTEGER

wlan2DhcpRelay		1.3.6.1.4.1.24350.13.4.4
OBJECT IDENTIFIER

wlan2DhcpRelayEnable		1.3.6.1.4.1.24350.13.4.4.1
use dhcp relay (if sys.dhcp.relay.enable=yes)
Status: current	Access: read-write
OBJECT-TYPE
	OCTET STRING

wlan2DhcpReserve		1.3.6.1.4.1.24350.13.4.5
ip addresses to reserve at bottom of range for static assignments
Status: current	Access: read-write
OBJECT-TYPE
	INTEGER

wlan2DhcpRole		1.3.6.1.4.1.24350.13.4.6
interface dhcp role (none, client, server)
Status: current	Access: read-write
OBJECT-TYPE
	OCTET STRING

wlan2Enable		1.3.6.1.4.1.24350.13.5
interface is enabled
Status: current	Access: read-write
OBJECT-TYPE
	OCTET STRING

wlan2Enhsec		1.3.6.1.4.1.24350.13.6
ignore clients that specify 'ANY' ssid
Status: current	Access: read-write
OBJECT-TYPE
	OCTET STRING

wlan2Essid		1.3.6.1.4.1.24350.13.7
essid for this ap
Status: current	Access: read-write
OBJECT-TYPE
	OCTET STRING

wlan2Frag		1.3.6.1.4.1.24350.13.8
fragmentation threshold
Status: current	Access: read-write
OBJECT-TYPE
	OCTET STRING

wlan2Hideessid		1.3.6.1.4.1.24350.13.9
don't broadcast the essid
Status: current	Access: read-write
OBJECT-TYPE
	OCTET STRING

wlan2If		1.3.6.1.4.1.24350.13.10
interface associated with this module
Status: current	Access: read-only
OBJECT-TYPE
	OCTET STRING

wlan2Ip		1.3.6.1.4.1.24350.13.11
OBJECT IDENTIFIER

wlan2IpAddress		1.3.6.1.4.1.24350.13.11.1
ip address
Status: current	Access: read-only
OBJECT-TYPE
	OCTET STRING

wlan2IpAddressforce		1.3.6.1.4.1.24350.13.11.2
override .ip.address (or blank)
Status: current	Access: read-write
OBJECT-TYPE
	OCTET STRING

wlan2IpBroadcast		1.3.6.1.4.1.24350.13.11.3
broadcast address
Status: current	Access: read-only
OBJECT-TYPE
	OCTET STRING

wlan2IpBroadcastforce		1.3.6.1.4.1.24350.13.11.4
override .ip.broadcast (or blank)
Status: current	Access: read-write
OBJECT-TYPE
	OCTET STRING

wlan2IpGateway		1.3.6.1.4.1.24350.13.11.5
gateway address
Status: current	Access: read-only
OBJECT-TYPE
	OCTET STRING

wlan2IpGatewayforce		1.3.6.1.4.1.24350.13.11.6
override .ip.gateway (or blank)
Status: current	Access: read-write
OBJECT-TYPE
	OCTET STRING

wlan2IpImplicit		1.3.6.1.4.1.24350.13.11.7
OBJECT IDENTIFIER

wlan2IpImplicitSize		1.3.6.1.4.1.24350.13.11.7.1
OBJECT IDENTIFIER

wlan2IpImplicitSizeActual		1.3.6.1.4.1.24350.13.11.7.1.1
actual size of assigned address range
Status: current	Access: read-only
OBJECT-TYPE
	INTEGER

wlan2IpImplicitSizeRequested		1.3.6.1.4.1.24350.13.11.7.1.2
requested size of address range (multiple of 32 minus 1)
Status: current	Access: read-write
OBJECT-TYPE
	OCTET STRING

wlan2IpImplicitStart		1.3.6.1.4.1.24350.13.11.7.2
OBJECT IDENTIFIER

wlan2IpImplicitStartActual		1.3.6.1.4.1.24350.13.11.7.2.1
actual assigned fourth octet
Status: current	Access: read-only
OBJECT-TYPE
	INTEGER

wlan2IpImplicitStartRequested		1.3.6.1.4.1.24350.13.11.7.2.2
requested interface fourth octet (multiple of 32 plus 1)
Status: current	Access: read-write
OBJECT-TYPE
	OCTET STRING

wlan2IpNetmask		1.3.6.1.4.1.24350.13.11.8
network mask
Status: current	Access: read-only
OBJECT-TYPE
	OCTET STRING

wlan2IpNetmaskforce		1.3.6.1.4.1.24350.13.11.9
override .ip.netmask (or blank)
Status: current	Access: read-write
OBJECT-TYPE
	OCTET STRING

wlan2Iwconfig		1.3.6.1.4.1.24350.13.12
OBJECT IDENTIFIER

wlan2IwconfigCmd		1.3.6.1.4.1.24350.13.12.1
parameters to pass to iwconfig after all other settings
Status: current	Access: read-write
OBJECT-TYPE
	OCTET STRING

wlan2Iwpriv		1.3.6.1.4.1.24350.13.13
OBJECT IDENTIFIER

wlan2IwprivCmd		1.3.6.1.4.1.24350.13.13.1
parameters to pass to iwpriv after all other settings
Status: current	Access: read-write
OBJECT-TYPE
	OCTET STRING

wlan2Key		1.3.6.1.4.1.24350.13.14
wep key - if present, overrides .keys
Status: current	Access: read-write
OBJECT-TYPE
	OCTET STRING

wlan2Keys		1.3.6.1.4.1.24350.13.15
OBJECT IDENTIFIER

wlan2Keys1		1.3.6.1.4.1.24350.13.15.1
one of four keys selected with .keys.default
Status: current	Access: read-write
OBJECT-TYPE
	OCTET STRING

wlan2Keys2		1.3.6.1.4.1.24350.13.15.2
one of four keys selected with .keys.default
Status: current	Access: read-write
OBJECT-TYPE
	OCTET STRING

wlan2Keys3		1.3.6.1.4.1.24350.13.15.3
one of four keys selected with .keys.default
Status: current	Access: read-write
OBJECT-TYPE
	OCTET STRING

wlan2Keys4		1.3.6.1.4.1.24350.13.15.4
one of four keys selected with .keys.default
Status: current	Access: read-write
OBJECT-TYPE
	OCTET STRING

wlan2KeysDefault		1.3.6.1.4.1.24350.13.15.5
1 to 4 to choose which of wlan2.keys.1-4 to use
Status: current	Access: read-write
OBJECT-TYPE
	OCTET STRING

wlan2Mode		1.3.6.1.4.1.24350.13.16
operating mode ( ap/master, adhoc, adhoc-demo, sta/client )
Status: current	Access: read-write
OBJECT-TYPE
	OCTET STRING

wlan2Mtu		1.3.6.1.4.1.24350.13.17
maximum transmission unit - may cause serious problems if set too low
Status: current	Access: read-write
OBJECT-TYPE
	INTEGER

wlan2Radio		1.3.6.1.4.1.24350.13.18
which physical radio this vap is on (0 or 1)
Status: current	Access: read-write
OBJECT-TYPE
	OCTET STRING

wlan2Rate		1.3.6.1.4.1.24350.13.19
communications rate
Status: current	Access: read-write
OBJECT-TYPE
	OCTET STRING

wlan2Role		1.3.6.1.4.1.24350.13.20
intended interface role (access, bridge)
Status: current	Access: read-write
OBJECT-TYPE
	OCTET STRING

wlan2Routes		1.3.6.1.4.1.24350.13.21
OBJECT IDENTIFIER

wlan2RoutesStatic		1.3.6.1.4.1.24350.13.21.1
static routes for this interface
Status: current	Access: read-write
OBJECT-TYPE
	OCTET STRING

wlan2Vlan		1.3.6.1.4.1.24350.13.22
OBJECT IDENTIFIER

wlan2VlanEnable		1.3.6.1.4.1.24350.13.22.1
use a vlan for this interface
Status: current	Access: read-write
OBJECT-TYPE
	OCTET STRING

wlan2VlanId		1.3.6.1.4.1.24350.13.22.2
vlan id (0 and 1 are usually reserved)
Status: current	Access: read-write
OBJECT-TYPE
	INTEGER

wlan2Wpa		1.3.6.1.4.1.24350.13.23
OBJECT IDENTIFIER

wlan2WpaAuth		1.3.6.1.4.1.24350.13.23.1
OBJECT IDENTIFIER

wlan2WpaAuthArgs		1.3.6.1.4.1.24350.13.23.1.1
arguments passed to authenticator
Status: current	Access: read-write
OBJECT-TYPE
	OCTET STRING

wlan2WpaAuthCustom		1.3.6.1.4.1.24350.13.23.1.2
command used to start authenticator if .wpa.auth.type is 'custom'
Status: current	Access: read-write
OBJECT-TYPE
	OCTET STRING

wlan2WpaAuthInternal		1.3.6.1.4.1.24350.13.23.1.3
0 for external, 1 for internal
Status: current	Access: read-write
OBJECT-TYPE
	OCTET STRING

wlan2WpaAuthServer		1.3.6.1.4.1.24350.13.23.1.4
OBJECT IDENTIFIER

wlan2WpaAuthServerAddr		1.3.6.1.4.1.24350.13.23.1.4.1
authentication server address
Status: current	Access: read-write
OBJECT-TYPE
	OCTET STRING

wlan2WpaAuthServerPort		1.3.6.1.4.1.24350.13.23.1.4.2
authentication server port
Status: current	Access: read-write
OBJECT-TYPE
	INTEGER

wlan2WpaAuthServerSharedsecret		1.3.6.1.4.1.24350.13.23.1.4.3
shared secret
Status: current	Access: read-write
OBJECT-TYPE
	OCTET STRING

wlan2WpaAuthType		1.3.6.1.4.1.24350.13.23.1.5
'hostapd' or 'custom'
Status: current	Access: read-write
OBJECT-TYPE
	OCTET STRING

wlan2WpaBridge		1.3.6.1.4.1.24350.13.23.2
bridge if any, set by sys.l2.bridge.enable
Status: current	Access: read-only
OBJECT-TYPE
	OCTET STRING

wlan2WpaCa		1.3.6.1.4.1.24350.13.23.3
OBJECT IDENTIFIER

wlan2WpaCaCert		1.3.6.1.4.1.24350.13.23.3.1
OBJECT IDENTIFIER

wlan2WpaCaCertFile		1.3.6.1.4.1.24350.13.23.3.1.1
ca_cert file
Status: current	Access: read-write
OBJECT-TYPE
	OCTET STRING

wlan2WpaEapol		1.3.6.1.4.1.24350.13.23.4
OBJECT IDENTIFIER

wlan2WpaEapolVersion		1.3.6.1.4.1.24350.13.23.4.1
2 is default, but some older clients need 1
Status: current	Access: read-write
OBJECT-TYPE
	OCTET STRING

wlan2WpaEnable		1.3.6.1.4.1.24350.13.23.5
wpa support enabled?
Status: current	Access: read-write
OBJECT-TYPE
	OCTET STRING

wlan2WpaEssid		1.3.6.1.4.1.24350.13.23.6
essid for wpa authentication
Status: current	Access: read-write
OBJECT-TYPE
	OCTET STRING

wlan2WpaIf		1.3.6.1.4.1.24350.13.23.7
management frame interface, same as wlan2.if
Status: current	Access: read-only
OBJECT-TYPE
	OCTET STRING

wlan2WpaKeymgmt		1.3.6.1.4.1.24350.13.23.8
WPA-PSK and/or WPA-EAP
Status: current	Access: read-write
OBJECT-TYPE
	OCTET STRING

wlan2WpaMode		1.3.6.1.4.1.24350.13.23.9
wpa modes: 1=wpa1, 2=wpa2, 3=both
Status: current	Access: read-write
OBJECT-TYPE
	INTEGER

wlan2WpaNode		1.3.6.1.4.1.24350.13.23.10
OBJECT IDENTIFIER

wlan2WpaNodeCert		1.3.6.1.4.1.24350.13.23.10.1
OBJECT IDENTIFIER

wlan2WpaNodeCertFile		1.3.6.1.4.1.24350.13.23.10.1.1
server_cert file
Status: current	Access: read-write
OBJECT-TYPE
	OCTET STRING

wlan2WpaNodeKey		1.3.6.1.4.1.24350.13.23.10.2
OBJECT IDENTIFIER

wlan2WpaNodeKeyFile		1.3.6.1.4.1.24350.13.23.10.2.1
private_key file
Status: current	Access: read-write
OBJECT-TYPE
	OCTET STRING

wlan2WpaNodeKeyPassphrase		1.3.6.1.4.1.24350.13.23.10.2.2
passphrase for the node's private key
Status: current	Access: read-write
OBJECT-TYPE
	OCTET STRING

wlan2WpaPairwise		1.3.6.1.4.1.24350.13.23.11
accepted cipher suites - CCMP and/or TKIP
Status: current	Access: read-write
OBJECT-TYPE
	OCTET STRING

wlan2WpaPassphrase		1.3.6.1.4.1.24350.13.23.12
wpa passphrase
Status: current	Access: read-write
OBJECT-TYPE
	OCTET STRING

wlan3		1.3.6.1.4.1.24350.14
OBJECT IDENTIFIER

wlan3Acl		1.3.6.1.4.1.24350.14.1
OBJECT IDENTIFIER

wlan3AclMode		1.3.6.1.4.1.24350.14.1.1
access control list mode ( 'none', 'whitelist', 'blacklist' )
Status: current	Access: read-write
OBJECT-TYPE
	OCTET STRING

wlan3Beaconinterval		1.3.6.1.4.1.24350.14.2
beacon interval in milliseconds
Status: current	Access: read-write
OBJECT-TYPE
	INTEGER

wlan3Cellid		1.3.6.1.4.1.24350.14.3
cell id for adhoc mode
Status: current	Access: read-write
OBJECT-TYPE
	OCTET STRING

wlan3Dhcp		1.3.6.1.4.1.24350.14.4
OBJECT IDENTIFIER

wlan3DhcpAlwaysbroadcast		1.3.6.1.4.1.24350.14.4.1
always broadcast dhcp responses
Status: current	Access: read-write
OBJECT-TYPE
	OCTET STRING

wlan3DhcpDefaultleasetime		1.3.6.1.4.1.24350.14.4.2
default dhcp lease expiration in seconds
Status: current	Access: read-write
OBJECT-TYPE
	INTEGER

wlan3DhcpMaxleasetime		1.3.6.1.4.1.24350.14.4.3
maximum requestable dhcp lease expiration in seconds
Status: current	Access: read-write
OBJECT-TYPE
	INTEGER

wlan3DhcpRelay		1.3.6.1.4.1.24350.14.4.4
OBJECT IDENTIFIER

wlan3DhcpRelayEnable		1.3.6.1.4.1.24350.14.4.4.1
use dhcp relay (if sys.dhcp.relay.enable=yes)
Status: current	Access: read-write
OBJECT-TYPE
	OCTET STRING

wlan3DhcpReserve		1.3.6.1.4.1.24350.14.4.5
ip addresses to reserve at bottom of range for static assignments
Status: current	Access: read-write
OBJECT-TYPE
	INTEGER

wlan3DhcpRole		1.3.6.1.4.1.24350.14.4.6
interface dhcp role (none, client, server)
Status: current	Access: read-write
OBJECT-TYPE
	OCTET STRING

wlan3Enable		1.3.6.1.4.1.24350.14.5
interface is enabled
Status: current	Access: read-write
OBJECT-TYPE
	OCTET STRING

wlan3Enhsec		1.3.6.1.4.1.24350.14.6
ignore clients that specify 'ANY' ssid
Status: current	Access: read-write
OBJECT-TYPE
	OCTET STRING

wlan3Essid		1.3.6.1.4.1.24350.14.7
essid for this ap
Status: current	Access: read-write
OBJECT-TYPE
	OCTET STRING

wlan3Frag		1.3.6.1.4.1.24350.14.8
fragmentation threshold
Status: current	Access: read-write
OBJECT-TYPE
	OCTET STRING

wlan3Hideessid		1.3.6.1.4.1.24350.14.9
don't broadcast the essid
Status: current	Access: read-write
OBJECT-TYPE
	OCTET STRING

wlan3If		1.3.6.1.4.1.24350.14.10
interface associated with this module
Status: current	Access: read-only
OBJECT-TYPE
	OCTET STRING

wlan3Ip		1.3.6.1.4.1.24350.14.11
OBJECT IDENTIFIER

wlan3IpAddress		1.3.6.1.4.1.24350.14.11.1
ip address
Status: current	Access: read-only
OBJECT-TYPE
	OCTET STRING

wlan3IpAddressforce		1.3.6.1.4.1.24350.14.11.2
override .ip.address (or blank)
Status: current	Access: read-write
OBJECT-TYPE
	OCTET STRING

wlan3IpBroadcast		1.3.6.1.4.1.24350.14.11.3
broadcast address
Status: current	Access: read-only
OBJECT-TYPE
	OCTET STRING

wlan3IpBroadcastforce		1.3.6.1.4.1.24350.14.11.4
override .ip.broadcast (or blank)
Status: current	Access: read-write
OBJECT-TYPE
	OCTET STRING

wlan3IpGateway		1.3.6.1.4.1.24350.14.11.5
gateway address
Status: current	Access: read-only
OBJECT-TYPE
	OCTET STRING

wlan3IpGatewayforce		1.3.6.1.4.1.24350.14.11.6
override .ip.gateway (or blank)
Status: current	Access: read-write
OBJECT-TYPE
	OCTET STRING

wlan3IpImplicit		1.3.6.1.4.1.24350.14.11.7
OBJECT IDENTIFIER

wlan3IpImplicitSize		1.3.6.1.4.1.24350.14.11.7.1
OBJECT IDENTIFIER

wlan3IpImplicitSizeActual		1.3.6.1.4.1.24350.14.11.7.1.1
actual size of assigned address range
Status: current	Access: read-only
OBJECT-TYPE
	INTEGER

wlan3IpImplicitSizeRequested		1.3.6.1.4.1.24350.14.11.7.1.2
requested size of address range (multiple of 32 minus 1)
Status: current	Access: read-write
OBJECT-TYPE
	OCTET STRING

wlan3IpImplicitStart		1.3.6.1.4.1.24350.14.11.7.2
OBJECT IDENTIFIER

wlan3IpImplicitStartActual		1.3.6.1.4.1.24350.14.11.7.2.1
actual assigned fourth octet
Status: current	Access: read-only
OBJECT-TYPE
	INTEGER

wlan3IpImplicitStartRequested		1.3.6.1.4.1.24350.14.11.7.2.2
requested interface fourth octet (multiple of 32 plus 1)
Status: current	Access: read-write
OBJECT-TYPE
	OCTET STRING

wlan3IpNetmask		1.3.6.1.4.1.24350.14.11.8
network mask
Status: current	Access: read-only
OBJECT-TYPE
	OCTET STRING

wlan3IpNetmaskforce		1.3.6.1.4.1.24350.14.11.9
override .ip.netmask (or blank)
Status: current	Access: read-write
OBJECT-TYPE
	OCTET STRING

wlan3Iwconfig		1.3.6.1.4.1.24350.14.12
OBJECT IDENTIFIER

wlan3IwconfigCmd		1.3.6.1.4.1.24350.14.12.1
parameters to pass to iwconfig after all other settings
Status: current	Access: read-write
OBJECT-TYPE
	OCTET STRING

wlan3Iwpriv		1.3.6.1.4.1.24350.14.13
OBJECT IDENTIFIER

wlan3IwprivCmd		1.3.6.1.4.1.24350.14.13.1
parameters to pass to iwpriv after all other settings
Status: current	Access: read-write
OBJECT-TYPE
	OCTET STRING

wlan3Key		1.3.6.1.4.1.24350.14.14
wep key - if present, overrides .keys
Status: current	Access: read-write
OBJECT-TYPE
	OCTET STRING

wlan3Keys		1.3.6.1.4.1.24350.14.15
OBJECT IDENTIFIER

wlan3Keys1		1.3.6.1.4.1.24350.14.15.1
one of four keys selected with .keys.default
Status: current	Access: read-write
OBJECT-TYPE
	OCTET STRING

wlan3Keys2		1.3.6.1.4.1.24350.14.15.2
one of four keys selected with .keys.default
Status: current	Access: read-write
OBJECT-TYPE
	OCTET STRING

wlan3Keys3		1.3.6.1.4.1.24350.14.15.3
one of four keys selected with .keys.default
Status: current	Access: read-write
OBJECT-TYPE
	OCTET STRING

wlan3Keys4		1.3.6.1.4.1.24350.14.15.4
one of four keys selected with .keys.default
Status: current	Access: read-write
OBJECT-TYPE
	OCTET STRING

wlan3KeysDefault		1.3.6.1.4.1.24350.14.15.5
1 to 4 to choose which of wlan3.keys.1-4 to use
Status: current	Access: read-write
OBJECT-TYPE
	OCTET STRING

wlan3Mode		1.3.6.1.4.1.24350.14.16
operating mode ( ap/master, adhoc, adhoc-demo, sta/client )
Status: current	Access: read-write
OBJECT-TYPE
	OCTET STRING

wlan3Mtu		1.3.6.1.4.1.24350.14.17
maximum transmission unit - may cause serious problems if set too low
Status: current	Access: read-write
OBJECT-TYPE
	INTEGER

wlan3Radio		1.3.6.1.4.1.24350.14.18
which physical radio this vap is on (0 or 1)
Status: current	Access: read-write
OBJECT-TYPE
	OCTET STRING

wlan3Rate		1.3.6.1.4.1.24350.14.19
communications rate
Status: current	Access: read-write
OBJECT-TYPE
	OCTET STRING

wlan3Role		1.3.6.1.4.1.24350.14.20
intended interface role (access, bridge)
Status: current	Access: read-write
OBJECT-TYPE
	OCTET STRING

wlan3Routes		1.3.6.1.4.1.24350.14.21
OBJECT IDENTIFIER

wlan3RoutesStatic		1.3.6.1.4.1.24350.14.21.1
static routes for this interface
Status: current	Access: read-write
OBJECT-TYPE
	OCTET STRING

wlan3Vlan		1.3.6.1.4.1.24350.14.22
OBJECT IDENTIFIER

wlan3VlanEnable		1.3.6.1.4.1.24350.14.22.1
use a vlan for this interface
Status: current	Access: read-write
OBJECT-TYPE
	OCTET STRING

wlan3VlanId		1.3.6.1.4.1.24350.14.22.2
vlan id (0 and 1 are usually reserved)
Status: current	Access: read-write
OBJECT-TYPE
	INTEGER

wlan3Wpa		1.3.6.1.4.1.24350.14.23
OBJECT IDENTIFIER

wlan3WpaAuth		1.3.6.1.4.1.24350.14.23.1
OBJECT IDENTIFIER

wlan3WpaAuthArgs		1.3.6.1.4.1.24350.14.23.1.1
arguments passed to authenticator
Status: current	Access: read-write
OBJECT-TYPE
	OCTET STRING

wlan3WpaAuthCustom		1.3.6.1.4.1.24350.14.23.1.2
command used to start authenticator if .wpa.auth.type is 'custom'
Status: current	Access: read-write
OBJECT-TYPE
	OCTET STRING

wlan3WpaAuthInternal		1.3.6.1.4.1.24350.14.23.1.3
0 for external, 1 for internal
Status: current	Access: read-write
OBJECT-TYPE
	OCTET STRING

wlan3WpaAuthServer		1.3.6.1.4.1.24350.14.23.1.4
OBJECT IDENTIFIER

wlan3WpaAuthServerAddr		1.3.6.1.4.1.24350.14.23.1.4.1
authentication server address
Status: current	Access: read-write
OBJECT-TYPE
	OCTET STRING

wlan3WpaAuthServerPort		1.3.6.1.4.1.24350.14.23.1.4.2
authentication server port
Status: current	Access: read-write
OBJECT-TYPE
	INTEGER

wlan3WpaAuthServerSharedsecret		1.3.6.1.4.1.24350.14.23.1.4.3
shared secret
Status: current	Access: read-write
OBJECT-TYPE
	OCTET STRING

wlan3WpaAuthType		1.3.6.1.4.1.24350.14.23.1.5
'hostapd' or 'custom'
Status: current	Access: read-write
OBJECT-TYPE
	OCTET STRING

wlan3WpaBridge		1.3.6.1.4.1.24350.14.23.2
bridge if any, set by sys.l2.bridge.enable
Status: current	Access: read-only
OBJECT-TYPE
	OCTET STRING

wlan3WpaCa		1.3.6.1.4.1.24350.14.23.3
OBJECT IDENTIFIER

wlan3WpaCaCert		1.3.6.1.4.1.24350.14.23.3.1
OBJECT IDENTIFIER

wlan3WpaCaCertFile		1.3.6.1.4.1.24350.14.23.3.1.1
ca_cert file
Status: current	Access: read-write
OBJECT-TYPE
	OCTET STRING

wlan3WpaEapol		1.3.6.1.4.1.24350.14.23.4
OBJECT IDENTIFIER

wlan3WpaEapolVersion		1.3.6.1.4.1.24350.14.23.4.1
2 is default, but some older clients need 1
Status: current	Access: read-write
OBJECT-TYPE
	OCTET STRING

wlan3WpaEnable		1.3.6.1.4.1.24350.14.23.5
wpa support enabled?
Status: current	Access: read-write
OBJECT-TYPE
	OCTET STRING

wlan3WpaEssid		1.3.6.1.4.1.24350.14.23.6
essid for wpa authentication
Status: current	Access: read-write
OBJECT-TYPE
	OCTET STRING

wlan3WpaIf		1.3.6.1.4.1.24350.14.23.7
management frame interface, same as wlan3.if
Status: current	Access: read-only
OBJECT-TYPE
	OCTET STRING

wlan3WpaKeymgmt		1.3.6.1.4.1.24350.14.23.8
WPA-PSK and/or WPA-EAP
Status: current	Access: read-write
OBJECT-TYPE
	OCTET STRING

wlan3WpaMode		1.3.6.1.4.1.24350.14.23.9
wpa modes: 1=wpa1, 2=wpa2, 3=both
Status: current	Access: read-write
OBJECT-TYPE
	INTEGER

wlan3WpaNode		1.3.6.1.4.1.24350.14.23.10
OBJECT IDENTIFIER

wlan3WpaNodeCert		1.3.6.1.4.1.24350.14.23.10.1
OBJECT IDENTIFIER

wlan3WpaNodeCertFile		1.3.6.1.4.1.24350.14.23.10.1.1
server_cert file
Status: current	Access: read-write
OBJECT-TYPE
	OCTET STRING

wlan3WpaNodeKey		1.3.6.1.4.1.24350.14.23.10.2
OBJECT IDENTIFIER

wlan3WpaNodeKeyFile		1.3.6.1.4.1.24350.14.23.10.2.1
private_key file
Status: current	Access: read-write
OBJECT-TYPE
	OCTET STRING

wlan3WpaNodeKeyPassphrase		1.3.6.1.4.1.24350.14.23.10.2.2
passphrase for the node's private key
Status: current	Access: read-write
OBJECT-TYPE
	OCTET STRING

wlan3WpaPairwise		1.3.6.1.4.1.24350.14.23.11
accepted cipher suites - CCMP and/or TKIP
Status: current	Access: read-write
OBJECT-TYPE
	OCTET STRING

wlan3WpaPassphrase		1.3.6.1.4.1.24350.14.23.12
wpa passphrase
Status: current	Access: read-write
OBJECT-TYPE
	OCTET STRING

wlan4		1.3.6.1.4.1.24350.15
OBJECT IDENTIFIER

wlan4Acl		1.3.6.1.4.1.24350.15.1
OBJECT IDENTIFIER

wlan4AclMode		1.3.6.1.4.1.24350.15.1.1
access control list mode ( 'none', 'whitelist', 'blacklist' )
Status: current	Access: read-write
OBJECT-TYPE
	OCTET STRING

wlan4Beaconinterval		1.3.6.1.4.1.24350.15.2
beacon interval in milliseconds
Status: current	Access: read-write
OBJECT-TYPE
	INTEGER

wlan4Cellid		1.3.6.1.4.1.24350.15.3
cell id for adhoc mode
Status: current	Access: read-write
OBJECT-TYPE
	OCTET STRING

wlan4Dhcp		1.3.6.1.4.1.24350.15.4
OBJECT IDENTIFIER

wlan4DhcpAlwaysbroadcast		1.3.6.1.4.1.24350.15.4.1
always broadcast dhcp responses
Status: current	Access: read-write
OBJECT-TYPE
	OCTET STRING

wlan4DhcpDefaultleasetime		1.3.6.1.4.1.24350.15.4.2
default dhcp lease expiration in seconds
Status: current	Access: read-write
OBJECT-TYPE
	INTEGER

wlan4DhcpMaxleasetime		1.3.6.1.4.1.24350.15.4.3
maximum requestable dhcp lease expiration in seconds
Status: current	Access: read-write
OBJECT-TYPE
	INTEGER

wlan4DhcpRelay		1.3.6.1.4.1.24350.15.4.4
OBJECT IDENTIFIER

wlan4DhcpRelayEnable		1.3.6.1.4.1.24350.15.4.4.1
use dhcp relay (if sys.dhcp.relay.enable=yes)
Status: current	Access: read-write
OBJECT-TYPE
	OCTET STRING

wlan4DhcpReserve		1.3.6.1.4.1.24350.15.4.5
ip addresses to reserve at bottom of range for static assignments
Status: current	Access: read-write
OBJECT-TYPE
	INTEGER

wlan4DhcpRole		1.3.6.1.4.1.24350.15.4.6
interface dhcp role (none, client, server)
Status: current	Access: read-write
OBJECT-TYPE
	OCTET STRING

wlan4Enable		1.3.6.1.4.1.24350.15.5
interface is enabled
Status: current	Access: read-write
OBJECT-TYPE
	OCTET STRING

wlan4Enhsec		1.3.6.1.4.1.24350.15.6
ignore clients that specify 'ANY' ssid
Status: current	Access: read-write
OBJECT-TYPE
	OCTET STRING

wlan4Essid		1.3.6.1.4.1.24350.15.7
essid for this ap
Status: current	Access: read-write
OBJECT-TYPE
	OCTET STRING

wlan4Frag		1.3.6.1.4.1.24350.15.8
fragmentation threshold
Status: current	Access: read-write
OBJECT-TYPE
	OCTET STRING

wlan4Hideessid		1.3.6.1.4.1.24350.15.9
don't broadcast the essid
Status: current	Access: read-write
OBJECT-TYPE
	OCTET STRING

wlan4If		1.3.6.1.4.1.24350.15.10
interface associated with this module
Status: current	Access: read-only
OBJECT-TYPE
	OCTET STRING

wlan4Ip		1.3.6.1.4.1.24350.15.11
OBJECT IDENTIFIER

wlan4IpAddress		1.3.6.1.4.1.24350.15.11.1
ip address
Status: current	Access: read-only
OBJECT-TYPE
	OCTET STRING

wlan4IpAddressforce		1.3.6.1.4.1.24350.15.11.2
override .ip.address (or blank)
Status: current	Access: read-write
OBJECT-TYPE
	OCTET STRING

wlan4IpBroadcast		1.3.6.1.4.1.24350.15.11.3
broadcast address
Status: current	Access: read-only
OBJECT-TYPE
	OCTET STRING

wlan4IpBroadcastforce		1.3.6.1.4.1.24350.15.11.4
override .ip.broadcast (or blank)
Status: current	Access: read-write
OBJECT-TYPE
	OCTET STRING

wlan4IpGateway		1.3.6.1.4.1.24350.15.11.5
gateway address
Status: current	Access: read-only
OBJECT-TYPE
	OCTET STRING

wlan4IpGatewayforce		1.3.6.1.4.1.24350.15.11.6
override .ip.gateway (or blank)
Status: current	Access: read-write
OBJECT-TYPE
	OCTET STRING

wlan4IpImplicit		1.3.6.1.4.1.24350.15.11.7
OBJECT IDENTIFIER

wlan4IpImplicitSize		1.3.6.1.4.1.24350.15.11.7.1
OBJECT IDENTIFIER

wlan4IpImplicitSizeActual		1.3.6.1.4.1.24350.15.11.7.1.1
actual size of assigned address range
Status: current	Access: read-only
OBJECT-TYPE
	INTEGER

wlan4IpImplicitSizeRequested		1.3.6.1.4.1.24350.15.11.7.1.2
requested size of address range (multiple of 32 minus 1)
Status: current	Access: read-write
OBJECT-TYPE
	OCTET STRING

wlan4IpImplicitStart		1.3.6.1.4.1.24350.15.11.7.2
OBJECT IDENTIFIER

wlan4IpImplicitStartActual		1.3.6.1.4.1.24350.15.11.7.2.1
actual assigned fourth octet
Status: current	Access: read-only
OBJECT-TYPE
	INTEGER

wlan4IpImplicitStartRequested		1.3.6.1.4.1.24350.15.11.7.2.2
requested interface fourth octet (multiple of 32 plus 1)
Status: current	Access: read-write
OBJECT-TYPE
	OCTET STRING

wlan4IpNetmask		1.3.6.1.4.1.24350.15.11.8
network mask
Status: current	Access: read-only
OBJECT-TYPE
	OCTET STRING

wlan4IpNetmaskforce		1.3.6.1.4.1.24350.15.11.9
override .ip.netmask (or blank)
Status: current	Access: read-write
OBJECT-TYPE
	OCTET STRING

wlan4Iwconfig		1.3.6.1.4.1.24350.15.12
OBJECT IDENTIFIER

wlan4IwconfigCmd		1.3.6.1.4.1.24350.15.12.1
parameters to pass to iwconfig after all other settings
Status: current	Access: read-write
OBJECT-TYPE
	OCTET STRING

wlan4Iwpriv		1.3.6.1.4.1.24350.15.13
OBJECT IDENTIFIER

wlan4IwprivCmd		1.3.6.1.4.1.24350.15.13.1
parameters to pass to iwpriv after all other settings
Status: current	Access: read-write
OBJECT-TYPE
	OCTET STRING

wlan4Key		1.3.6.1.4.1.24350.15.14
wep key - if present, overrides .keys
Status: current	Access: read-write
OBJECT-TYPE
	OCTET STRING

wlan4Keys		1.3.6.1.4.1.24350.15.15
OBJECT IDENTIFIER

wlan4Keys1		1.3.6.1.4.1.24350.15.15.1
one of four keys selected with .keys.default
Status: current	Access: read-write
OBJECT-TYPE
	OCTET STRING

wlan4Keys2		1.3.6.1.4.1.24350.15.15.2
one of four keys selected with .keys.default
Status: current	Access: read-write
OBJECT-TYPE
	OCTET STRING

wlan4Keys3		1.3.6.1.4.1.24350.15.15.3
one of four keys selected with .keys.default
Status: current	Access: read-write
OBJECT-TYPE
	OCTET STRING

wlan4Keys4		1.3.6.1.4.1.24350.15.15.4
one of four keys selected with .keys.default
Status: current	Access: read-write
OBJECT-TYPE
	OCTET STRING

wlan4KeysDefault		1.3.6.1.4.1.24350.15.15.5
1 to 4 to choose which of wlan4.keys.1-4 to use
Status: current	Access: read-write
OBJECT-TYPE
	OCTET STRING

wlan4Mode		1.3.6.1.4.1.24350.15.16
operating mode ( ap/master, adhoc, adhoc-demo, sta/client )
Status: current	Access: read-write
OBJECT-TYPE
	OCTET STRING

wlan4Mtu		1.3.6.1.4.1.24350.15.17
maximum transmission unit - may cause serious problems if set too low
Status: current	Access: read-write
OBJECT-TYPE
	INTEGER

wlan4Radio		1.3.6.1.4.1.24350.15.18
which physical radio this vap is on (0 or 1)
Status: current	Access: read-write
OBJECT-TYPE
	OCTET STRING

wlan4Rate		1.3.6.1.4.1.24350.15.19
communications rate
Status: current	Access: read-write
OBJECT-TYPE
	OCTET STRING

wlan4Role		1.3.6.1.4.1.24350.15.20
intended interface role (access, bridge)
Status: current	Access: read-write
OBJECT-TYPE
	OCTET STRING

wlan4Routes		1.3.6.1.4.1.24350.15.21
OBJECT IDENTIFIER

wlan4RoutesStatic		1.3.6.1.4.1.24350.15.21.1
static routes for this interface
Status: current	Access: read-write
OBJECT-TYPE
	OCTET STRING

wlan4Vlan		1.3.6.1.4.1.24350.15.22
OBJECT IDENTIFIER

wlan4VlanEnable		1.3.6.1.4.1.24350.15.22.1
use a vlan for this interface
Status: current	Access: read-write
OBJECT-TYPE
	OCTET STRING

wlan4VlanId		1.3.6.1.4.1.24350.15.22.2
vlan id (0 and 1 are usually reserved)
Status: current	Access: read-write
OBJECT-TYPE
	INTEGER

wlan4Wpa		1.3.6.1.4.1.24350.15.23
OBJECT IDENTIFIER

wlan4WpaAuth		1.3.6.1.4.1.24350.15.23.1
OBJECT IDENTIFIER

wlan4WpaAuthArgs		1.3.6.1.4.1.24350.15.23.1.1
arguments passed to authenticator
Status: current	Access: read-write
OBJECT-TYPE
	OCTET STRING

wlan4WpaAuthCustom		1.3.6.1.4.1.24350.15.23.1.2
command used to start authenticator if .wpa.auth.type is 'custom'
Status: current	Access: read-write
OBJECT-TYPE
	OCTET STRING

wlan4WpaAuthInternal		1.3.6.1.4.1.24350.15.23.1.3
0 for external, 1 for internal
Status: current	Access: read-write
OBJECT-TYPE
	OCTET STRING

wlan4WpaAuthServer		1.3.6.1.4.1.24350.15.23.1.4
OBJECT IDENTIFIER

wlan4WpaAuthServerAddr		1.3.6.1.4.1.24350.15.23.1.4.1
authentication server address
Status: current	Access: read-write
OBJECT-TYPE
	OCTET STRING

wlan4WpaAuthServerPort		1.3.6.1.4.1.24350.15.23.1.4.2
authentication server port
Status: current	Access: read-write
OBJECT-TYPE
	INTEGER

wlan4WpaAuthServerSharedsecret		1.3.6.1.4.1.24350.15.23.1.4.3
shared secret
Status: current	Access: read-write
OBJECT-TYPE
	OCTET STRING

wlan4WpaAuthType		1.3.6.1.4.1.24350.15.23.1.5
'hostapd' or 'custom'
Status: current	Access: read-write
OBJECT-TYPE
	OCTET STRING

wlan4WpaBridge		1.3.6.1.4.1.24350.15.23.2
bridge if any, set by sys.l2.bridge.enable
Status: current	Access: read-only
OBJECT-TYPE
	OCTET STRING

wlan4WpaCa		1.3.6.1.4.1.24350.15.23.3
OBJECT IDENTIFIER

wlan4WpaCaCert		1.3.6.1.4.1.24350.15.23.3.1
OBJECT IDENTIFIER

wlan4WpaCaCertFile		1.3.6.1.4.1.24350.15.23.3.1.1
ca_cert file
Status: current	Access: read-write
OBJECT-TYPE
	OCTET STRING

wlan4WpaEapol		1.3.6.1.4.1.24350.15.23.4
OBJECT IDENTIFIER

wlan4WpaEapolVersion		1.3.6.1.4.1.24350.15.23.4.1
2 is default, but some older clients need 1
Status: current	Access: read-write
OBJECT-TYPE
	OCTET STRING

wlan4WpaEnable		1.3.6.1.4.1.24350.15.23.5
wpa support enabled?
Status: current	Access: read-write
OBJECT-TYPE
	OCTET STRING

wlan4WpaEssid		1.3.6.1.4.1.24350.15.23.6
essid for wpa authentication
Status: current	Access: read-write
OBJECT-TYPE
	OCTET STRING

wlan4WpaIf		1.3.6.1.4.1.24350.15.23.7
management frame interface, same as wlan4.if
Status: current	Access: read-only
OBJECT-TYPE
	OCTET STRING

wlan4WpaKeymgmt		1.3.6.1.4.1.24350.15.23.8
WPA-PSK and/or WPA-EAP
Status: current	Access: read-write
OBJECT-TYPE
	OCTET STRING

wlan4WpaMode		1.3.6.1.4.1.24350.15.23.9
wpa modes: 1=wpa1, 2=wpa2, 3=both
Status: current	Access: read-write
OBJECT-TYPE
	INTEGER

wlan4WpaNode		1.3.6.1.4.1.24350.15.23.10
OBJECT IDENTIFIER

wlan4WpaNodeCert		1.3.6.1.4.1.24350.15.23.10.1
OBJECT IDENTIFIER

wlan4WpaNodeCertFile		1.3.6.1.4.1.24350.15.23.10.1.1
server_cert file
Status: current	Access: read-write
OBJECT-TYPE
	OCTET STRING

wlan4WpaNodeKey		1.3.6.1.4.1.24350.15.23.10.2
OBJECT IDENTIFIER

wlan4WpaNodeKeyFile		1.3.6.1.4.1.24350.15.23.10.2.1
private_key file
Status: current	Access: read-write
OBJECT-TYPE
	OCTET STRING

wlan4WpaNodeKeyPassphrase		1.3.6.1.4.1.24350.15.23.10.2.2
passphrase for the node's private key
Status: current	Access: read-write
OBJECT-TYPE
	OCTET STRING

wlan4WpaPairwise		1.3.6.1.4.1.24350.15.23.11
accepted cipher suites - CCMP and/or TKIP
Status: current	Access: read-write
OBJECT-TYPE
	OCTET STRING

wlan4WpaPassphrase		1.3.6.1.4.1.24350.15.23.12
wpa passphrase
Status: current	Access: read-write
OBJECT-TYPE
	OCTET STRING

enRouteTraps		1.3.6.1.4.1.24350.100
OBJECT IDENTIFIER

enRouteConfigChange		1
This trap is triggered when any modification is done in the node configuration. Important note: modifying interface status on a node does not send a linkDown or linkUp trap to the NMS because the change occurs at a node reboot. Only a config change trap (this one) is sent.
TRAP-TYPE

enRouteConfigReset		2
This trap is triggered when the node configuration is reloaded
TRAP-TYPE