TPLINK-LLDPCONFIG-MIB

File: TPLINK-LLDPCONFIG-MIB.mib (13368 bytes)

Imported modules

TPLINK-TC-MIB SNMPv2-SMI TPLINK-LLDP-MIB
RFC1213-MIB

Imported symbols

TPRowStatus OBJECT-TYPE IpAddress
tplinkLldpMIBObjects ifIndex

Defined Types

MacAddress  
OCTET STRING Size(6)    

LLDPPORTCONFIGENTRY  
SEQUENCE    
  lldpConfigPortId OCTET STRING
  lldpConfigPortStatus INTEGER
  lldpConfigPortSnmpNotifyEnable INTEGER
  lldpConfigPortTlvDescr INTEGER
  lldpConfigPortTlvSysCap INTEGER
  lldpConfigPortTlvSysDescr INTEGER
  lldpConfigPortTlvSysName INTEGER
  lldpConfigPortTlvManageAddr INTEGER
  lldpConfigPortTlvPortVlanId INTEGER
  lldpConfigPortTlvProtoVlanId INTEGER
  lldpConfigPortTlvVlanName INTEGER
  lldpConfigPortTlvLinkAggre INTEGER
  lldpConfigPortTlvPortStatus INTEGER
  lldpConfigPortTlvMaxFrame INTEGER
  lldpConfigPortTlvPower INTEGER

Defined Values

lldpConfig 1.3.6.1.4.1.11863.6.35.1.1
OBJECT IDENTIFIER    

lldpGlobalConfig 1.3.6.1.4.1.11863.6.35.1.1.1
OBJECT IDENTIFIER    

lldpGlobalConfigEnable 1.3.6.1.4.1.11863.6.35.1.1.1.1
Select Enable/Disable LLDP function globally on the Switch. 0. disable 1. enable
Status: current Access: read-write
OBJECT-TYPE    
  INTEGER disable(0), enable(1)  

lldpGlobalConfigTxInterval 1.3.6.1.4.1.11863.6.35.1.1.1.2
The interval of the local device send the LLDPDU to the neighbor device.
Status: current Access: read-write
OBJECT-TYPE    
  INTEGER 5..32768  

lldpGlobalConfigTtl 1.3.6.1.4.1.11863.6.35.1.1.1.3
TTL multiplier determines the TTL value in the LLDPDU packet which the local device send to the neighbor device. TTL value is the time of the local information enabled in the neighbor device, TTL value = TTL multiplier * interval
Status: current Access: read-write
OBJECT-TYPE    
  INTEGER 2..10  

lldpGlobalConfigTxDelay 1.3.6.1.4.1.11863.6.35.1.1.1.4
The delay time of the local device send the LLDPDU packet to the neighbor device. When the config of the local device is changed, it will notify the neighbor device after the setting time delay, which can avoid continually sending the LLPDDU packet to the neighbor device when local device continually change the config.
Status: current Access: read-write
OBJECT-TYPE    
  INTEGER 1..8192  

lldpGlobalConfigInitDelay 1.3.6.1.4.1.11863.6.35.1.1.1.5
When the LLDP mode is changed, the device will initialize after a setting time delay, which can avoid continually initialized when the device continually change the LLDP mode .
Status: current Access: read-write
OBJECT-TYPE    
  INTEGER 1..10  

lldpGlobalConfigTrap 1.3.6.1.4.1.11863.6.35.1.1.1.6
The interval of sending the trap information. When a trap event has happened,just as finded a new neighbor or the neighbor information has changed,the local device would send a trap information to the SNMP server.
Status: current Access: read-write
OBJECT-TYPE    
  INTEGER 5..3600  

lldpGlobalConfigFastCount 1.3.6.1.4.1.11863.6.35.1.1.1.7
When the LLDP mode of the port changed from disable(or just receive) to send and receive(or just send), the quick send mechanism will be enabled for other device find the local device as fast as it can,and at this time, the LLDP packet is sended per second, and it get right after sended the setting num LLDPDU packet.
Status: current Access: read-write
OBJECT-TYPE    
  INTEGER 1..10  

lldpPortConfigTable 1.3.6.1.4.1.11863.6.35.1.1.2
A table that contains LLDP information of every port.
Status: current Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    LLDPPORTCONFIGENTRY

lldpPortConfigEntry 1.3.6.1.4.1.11863.6.35.1.1.2.1
A list of LLDP information for every port of the device.
Status: current Access: not-accessible
OBJECT-TYPE    
  LLDPPORTCONFIGENTRY  

lldpConfigPortId 1.3.6.1.4.1.11863.6.35.1.1.2.1.1
The port id of the switch.
Status: current Access: read-only
OBJECT-TYPE    
  OCTET STRING Size(0..255)  

lldpConfigPortStatus 1.3.6.1.4.1.11863.6.35.1.1.2.1.2
Select Enable/Disable Tx/Rx for the Port. 0. Disable 1. EnableTx 2. EnableRx 3. EnableRxTx
Status: current Access: read-write
OBJECT-TYPE    
  INTEGER disable(0), enableTx(1), enableRx(2), enableRxTx(3)  

lldpConfigPortSnmpNotifyEnable 1.3.6.1.4.1.11863.6.35.1.1.2.1.3
Select Enable/Disable Snmp Notify for the Port. 0. Disable 1. Enable
Status: current Access: read-write
OBJECT-TYPE    
  INTEGER disable(0), enable(1)  

lldpConfigPortTlvDescr 1.3.6.1.4.1.11863.6.35.1.1.2.1.4
Select Enable/Disable TLV description for the Port. 0. Disable 1. Enable
Status: current Access: read-write
OBJECT-TYPE    
  INTEGER disable(0), enable(1)  

lldpConfigPortTlvSysCap 1.3.6.1.4.1.11863.6.35.1.1.2.1.5
Select Enable/Disable TLV system cap for the Port. 0. Disable 1. Enable
Status: current Access: read-write
OBJECT-TYPE    
  INTEGER disable(0), enable(1)  

lldpConfigPortTlvSysDescr 1.3.6.1.4.1.11863.6.35.1.1.2.1.6
Select Enable/Disable TLV System description for the Port. 0. Disable 1. Enable
Status: current Access: read-write
OBJECT-TYPE    
  INTEGER disable(0), enable(1)  

lldpConfigPortTlvSysName 1.3.6.1.4.1.11863.6.35.1.1.2.1.7
Select Enable/Disable TLV System name for the Port. 0. Disable 1. Enable
Status: current Access: read-write
OBJECT-TYPE    
  INTEGER disable(0), enable(1)  

lldpConfigPortTlvManageAddr 1.3.6.1.4.1.11863.6.35.1.1.2.1.8
Select Enable/Disable TLV manage address for the Port. 0. Disable 1. Enable
Status: current Access: read-write
OBJECT-TYPE    
  INTEGER disable(0), enable(1)  

lldpConfigPortTlvPortVlanId 1.3.6.1.4.1.11863.6.35.1.1.2.1.9
Select Enable/Disable TLV port Vlan ID for the Port. 0. Disable 1. Enable
Status: current Access: read-write
OBJECT-TYPE    
  INTEGER disable(0), enable(1)  

lldpConfigPortTlvProtoVlanId 1.3.6.1.4.1.11863.6.35.1.1.2.1.10
Select Enable/Disable TLV Portocol VlanId for the Port. 0. Disable 1. Enable
Status: current Access: read-write
OBJECT-TYPE    
  INTEGER disable(0), enable(1)  

lldpConfigPortTlvVlanName 1.3.6.1.4.1.11863.6.35.1.1.2.1.11
Select Enable/Disable TLV Vlan name for the Port. 0. Disable 1. Enable
Status: current Access: read-write
OBJECT-TYPE    
  INTEGER disable(0), enable(1)  

lldpConfigPortTlvLinkAggre 1.3.6.1.4.1.11863.6.35.1.1.2.1.12
Select Enable/Disable TLV link aggre for the Port. 0. Disable 1. Enable
Status: current Access: read-write
OBJECT-TYPE    
  INTEGER disable(0), enable(1)  

lldpConfigPortTlvPortStatus 1.3.6.1.4.1.11863.6.35.1.1.2.1.13
Select Enable/Disable TLV port status for the Port. 0. Disable 1. Enable
Status: current Access: read-write
OBJECT-TYPE    
  INTEGER disable(0), enable(1)  

lldpConfigPortTlvMaxFrame 1.3.6.1.4.1.11863.6.35.1.1.2.1.14
Select Enable/Disable TLV max frame for the Port. 0. Disable 1. Enable
Status: current Access: read-write
OBJECT-TYPE    
  INTEGER disable(0), enable(1)  

lldpConfigPortTlvPower 1.3.6.1.4.1.11863.6.35.1.1.2.1.15
Select Enable/Disable TLV power for the Port. 0. Disable 1. Enable
Status: current Access: read-write
OBJECT-TYPE    
  INTEGER disable(0), enable(1)