TIMETRA-ETH-TUNNEL-MIB

File: TIMETRA-ETH-TUNNEL-MIB.mib (50571 bytes)

Imported modules

SNMPv2-SMI SNMPv2-CONF SNMPv2-TC
TIMETRA-GLOBAL-MIB IF-MIB TIMETRA-SERV-MIB
TIMETRA-SAP-MIB TIMETRA-TC-MIB TIMETRA-CHASSIS-MIB

Imported symbols

MODULE-IDENTITY OBJECT-TYPE NOTIFICATION-TYPE
Unsigned32 Counter32 MODULE-COMPLIANCE
OBJECT-GROUP TEXTUAL-CONVENTION RowStatus
TimeStamp TruthValue timetraSRMIBModules
tmnxSRObjs tmnxSRNotifyPrefix tmnxSRConfs
InterfaceIndexOrZero svcId sapPortId
sapEncapValue TmnxAdminState TmnxOperState
TmnxEncapVal TItemDescription TmnxChassisIndex

Defined Types

TmnxEthTunnelIndex  
The TmnxEthTunnelIndex specifies the unique Ethernet Tunnel Identifier for an Ethernet Tunnel Group. The value of zero (0) is only used by objects which may reference a tmnxEthTunnelConfigEntry. The value zero (0) is an invalid index that specifies that the object is not associated with any Ethernet Tunnel Group.
TEXTUAL-CONVENTION    
  Unsigned32  

TmnxEthTunnelMemberIndex  
The TmnxEthTunnelMemberIndex specifies the unique Ethernet Tunnel Member Identifier. Along with an Object of type TmnxEthTunnelIndex, an Object of this type references a specific member on a specific ethernet tunnel group. The value of zero (0), is only used by objects which may reference a tmnxEthTunnelMemberEntry. The value of zero (0) is an invalid index that specifies that the object is not associated with any Ethernet Tunnel Member.
TEXTUAL-CONVENTION    
  Unsigned32  

TmnxEthTunnelMemberList  
The TmnxEthTunnelMemberList specifies a bit-mask of the members associated with a particular object. Each bit represents a specific tmnxEthTunnelMemberEntry. Bit 0 (first bit) represents the member with the tmnxEthTunnelMemberIndex value of 1. Bit 1, represents the member with the tmnxEthTunnelMemberIndex value of 2, and so forth. member1 (0) -- represents member 1. member2 (1) -- represents member 2. etc.
TEXTUAL-CONVENTION    
  BITS member1(0), member2(1), member3(2), member4(3), member5(4), member6(5), member7(6), member8(7), member9(8), member10(9), member11(10), member12(11), member13(12), member14(13), member15(14), member16(15)  

TmnxEthTunnelApsPduType  
The TmnxEthTunnelApsPduType specifies the 4 byte APS-specific information within each APS PDU. The information is encoded as shown below. 32 29|28 25|24 17|16 9|8 1| +-------+---------+--------+--------+--------+ |Request|Prot.Type|Request |Bridge |Reserved| | State| A|B|D|R | Signal| Signal| | +-------+---------+--------+--------+--------+
TEXTUAL-CONVENTION    
  Unsigned32  

TmnxEthTunnelConfigEntry  
SEQUENCE    
  tmnxEthTunnelIndex TmnxEthTunnelIndex
  tmnxEthTunnelRowStatus RowStatus
  tmnxEthTunnelTimeStamp TimeStamp
  tmnxEthTunnelHoldDownTimeMember Unsigned32
  tmnxEthTunnelProtectionType INTEGER
  tmnxEthTunnelRevertTime Unsigned32
  tmnxEthTunnelHoldUpTimeMember Unsigned32

TmnxEthTunnelOperEntry  
SEQUENCE    
  tmnxEthTunnelChassisIndex TmnxChassisIndex
  tmnxEthTunnelIfIndex InterfaceIndexOrZero
  tmnxEthTunnelMgmtMemberIfIndex InterfaceIndexOrZero
  tmnxEthTunnelActiveMembers TmnxEthTunnelMemberList
  tmnxEthTunnelRevertTimeCountDn Unsigned32

TmnxEthTunnelMemberEntry  
SEQUENCE    
  tmnxEthTunnelMemberIndex TmnxEthTunnelMemberIndex
  tmnxEthTunnelMemberRowStatus RowStatus
  tmnxEthTunnelMemberTimeStamp TimeStamp
  tmnxEthTunnelMemberIfIndex InterfaceIndexOrZero
  tmnxEthTunnelMemberIfCtlTag TmnxEncapVal
  tmnxEthTunnelMemberDescription TItemDescription
  tmnxEthTunnelMemberAdminStatus TmnxAdminState
  tmnxEthTunnelMemberOperStatus TmnxOperState
  tmnxEthTunnelMemberPrecedence Unsigned32

TmnxEthTunnelApsEntry  
SEQUENCE    
  tmnxEthTunnelApsRxPdu TmnxEthTunnelApsPduType
  tmnxEthTunnelApsTxPdu TmnxEthTunnelApsPduType
  tmnxEthTunnelApsDefectStatus BITS
  tmnxEthTunnelApsSwitchoverTime TimeStamp

TmnxEthTunnelApsMemberEntry  
SEQUENCE    
  tmnxEthTunnelApsMemberActCount Counter32
  tmnxEthTunnelApsMemberActTime Counter32

TmnxEthTunnelApsCommandEntry  
SEQUENCE    
  tmnxEthTunnelApsCommandSwitch INTEGER
  tmnxEthTunnelApsCommandExsResult INTEGER

TmnxEthTunnelLEEntry  
SEQUENCE    
  tmnxEthTunnelLEAccessAdaptQos INTEGER
  tmnxEthTunnelLEPerFpIngQueueing TruthValue
  tmnxEthTunnelLEMbrThreshold Unsigned32

TmnxEthTunnelSAPMemberEntry  
SEQUENCE    
  tmnxEthTunnelSAPMemberRowStatus RowStatus
  tmnxEthTunnelSAPMemberTagValue TmnxEncapVal

Defined Values

timetraEthTunnelMIBModule 1.3.6.1.4.1.6527.1.1.3.64
This document is the SNMP MIB module to manage and provision the Ethernet Tunnel components of the Alcatel-Lucent SROS device. Copyright (c) 2009-2011 Alcatel-Lucent. All rights reserved. Reproduction of this document is authorized on the condition that the foregoing copyright notice is included. This SNMP MIB module (Specification) embodies Alcatel-Lucent's proprietary intellectual property. Alcatel-Lucent retains all title and ownership in the Specification, including any revisions. Alcatel-Lucent grants all interested parties a non-exclusive license to use and distribute an unmodified copy of this Specification in connection with management of Alcatel-Lucent products, and without fee, provided this copyright notice and license appear on all copies. This Specification is supplied 'as is', and Alcatel-Lucent makes no warranty, either express or implied, as to the use, operation, condition, or performance of the Specification.
MODULE-IDENTITY    

tmnxEthTunnelObjs 1.3.6.1.4.1.6527.3.1.2.64
OBJECT IDENTIFIER    

tmnxEthTunnelNotifyPrefix 1.3.6.1.4.1.6527.3.1.3.64
OBJECT IDENTIFIER    

tmnxEthTunnelConformance 1.3.6.1.4.1.6527.3.1.1.64
OBJECT IDENTIFIER    

tmnxEthTunnelConfigTimeStamps 1.3.6.1.4.1.6527.3.1.2.64.0
OBJECT IDENTIFIER    

tmnxEthTunnelConfigurations 1.3.6.1.4.1.6527.3.1.2.64.1
OBJECT IDENTIFIER    

tmnxEthTunnelStatistics 1.3.6.1.4.1.6527.3.1.2.64.2
OBJECT IDENTIFIER    

tmnxEthTunnelNotifications 1.3.6.1.4.1.6527.3.1.3.64.0
OBJECT IDENTIFIER    

tmnxEthTunnelCompliances 1.3.6.1.4.1.6527.3.1.1.64.1
OBJECT IDENTIFIER    

tmnxEthTunnelGroups 1.3.6.1.4.1.6527.3.1.1.64.2
OBJECT IDENTIFIER    

tmnxEthTunnelCfgTblLastChanged 1.3.6.1.4.1.6527.3.1.2.64.0.1
The tmnxEthTunnelCfgTblLastChanged indicates the time, since system startup, when a row in the tmnxEthTunnelConfigTable last changed.
Status: current Access: read-only
OBJECT-TYPE    
  TimeStamp  

tmnxEthTunnelConfigTable 1.3.6.1.4.1.6527.3.1.2.64.1.1
The tmnxEthTunnelConfigTable consists of the Ethernet Tunnel Group configuration information.
Status: current Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    TmnxEthTunnelConfigEntry

tmnxEthTunnelConfigEntry 1.3.6.1.4.1.6527.3.1.2.64.1.1.1
The tmnxEthTunnelConfigEntry contains information pertaining to an individual Ethernet Tunnel Group. Rows in this table are created and destroyed using the tmnxEthTunnelRowStatus object. A corresponding row in the tmnxPortTable will exist for each row in this table, based on the tmnxEthTunnelOperEntry tmnxEthTunnelChassisIndex and tmnxEthTunnelIfIndex object pair. The tmnxPortEntry corresponding to this entry manages the administration, description, MAC address and other port related configuration.
Status: current Access: not-accessible
OBJECT-TYPE    
  TmnxEthTunnelConfigEntry  

tmnxEthTunnelIndex 1.3.6.1.4.1.6527.3.1.2.64.1.1.1.1
The tmnxEthTunnelIndex specifies the row index of the Ethernet Tunnel Group.
Status: current Access: not-accessible
OBJECT-TYPE    
  TmnxEthTunnelIndex 1..4294967295  

tmnxEthTunnelRowStatus 1.3.6.1.4.1.6527.3.1.2.64.1.1.1.2
The tmnxEthTunnelRowStatus controls the creation and deletion of row entries in the tmnxEthTunnelConfigTable. A corresponding row in the tmnxPortTable is created by the system when a tmnxEthTunnelRowStatus value of 'createAndGo (4)' is issued on a new row in the tmnxEthTunnelConfigTable. The corresponding row in the tmnxPortTable will be destroyed by the system when the tmnxEthTunnelRowStatus value of 'destroy (6)' is issued.
Status: current Access: read-create
OBJECT-TYPE    
  RowStatus  

tmnxEthTunnelTimeStamp 1.3.6.1.4.1.6527.3.1.2.64.1.1.1.3
The tmnxEthTunnelTimeStamp indicates the time, since system startup, of the last change to this row.
Status: current Access: read-only
OBJECT-TYPE    
  TimeStamp  

tmnxEthTunnelHoldDownTimeMember 1.3.6.1.4.1.6527.3.1.2.64.1.1.1.4
The value of tmnxEthTunnelHoldDownTimeMember specifies the time, in centiseconds, used for the hold-timer for associated Continuity Check (CC) Session down event dampening. This guards against reporting excessive member operational state transitions. This is implemented by not advertising subsequent transitions of the CC state to the Ethernet Tunnel Group until the configured timer has expired. A value of zero (0) specifies that a down transition is reported immediately.
Status: current Access: read-create
OBJECT-TYPE    
  Unsigned32 0..1000  

tmnxEthTunnelProtectionType 1.3.6.1.4.1.6527.3.1.2.64.1.1.1.5
The value of tmnxEthTunnelProtectionType specifies the model used for determining which members are actively receiving and transmitting data. When the value is set to 'g8031-1to1 (1)', as per G.8031 spec, only two members are allowed, and only one of them can be active at one point in time. When the value is set to 'loadsharing (2)', multiple members can be active at one point in time. The value of tmnxEthTunnelProtectionType can only be changed when the corresponding tmnxPortEntry row object tmnxPortAdminStatus is set to 'outOfService (3)'
Status: current Access: read-create
OBJECT-TYPE    
  INTEGER g8031-1to1(1), loadsharing(2)  

tmnxEthTunnelRevertTime 1.3.6.1.4.1.6527.3.1.2.64.1.1.1.6
The value of tmnxEthTunnelRevertTime specifies the time, in seconds, that the tunnel waits to restore the working member. A value of zero (0) sets the behavior of the Ethernet Tunnel Group to be non-revertive, while a positive value specifies the wait time. After clearing of a condition that necessitated an automatic switch, the wait to restore period, indicated by reading the tmnxEthTunnelRevertTimeCountDn object, must elapse before reverting. This is intended to avoid rapid switch oscillations. This object is only applicable when the tmnxEthTunnelProtectionType is set to 'g8031-1to1 (1)'.
Status: current Access: read-create
OBJECT-TYPE    
  Unsigned32 0 | 1..720  

tmnxEthTunnelHoldUpTimeMember 1.3.6.1.4.1.6527.3.1.2.64.1.1.1.7
The value of tmnxEthTunnelHoldUpTimeMember specifies the time, in deciseconds, used for the hold-timer for associated Continuity Check (CC) Session up event dampening. This guards against reporting excessive member operational state transitions. This is implemented by not advertising subsequent transitions of the CC state to the Ethernet Tunnel Group until the configured timer has expired. A value of zero (0) specifies that an up transition is reported immediately.
Status: current Access: read-create
OBJECT-TYPE    
  Unsigned32 0..5000  

tmnxEthTunnelOperTable 1.3.6.1.4.1.6527.3.1.2.64.1.2
The tmnxEthTunnelOperTable consists of the Ethernet Tunnel Group operational information. This table augments the tmnxEthTunnelConfigTable.
Status: current Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    TmnxEthTunnelOperEntry

tmnxEthTunnelOperEntry 1.3.6.1.4.1.6527.3.1.2.64.1.2.1
The tmnxEthTunnelOperEntry contains information pertaining to an individual Ethernet Tunnel Group's operational state.
Status: current Access: not-accessible
OBJECT-TYPE    
  TmnxEthTunnelOperEntry  

tmnxEthTunnelChassisIndex 1.3.6.1.4.1.6527.3.1.2.64.1.2.1.1
The tmnxEthTunnelChassisIndex indicates the chassis index for the Ethernet Tunnel Group. The tmnxEthTunnelChassisIndex along with the tmnxEthTunnelIfIndex specifies the row in tmnxPortEntry that corresponds to the Ethernet Tunnel Group.
Status: current Access: read-only
OBJECT-TYPE    
  TmnxChassisIndex  

tmnxEthTunnelIfIndex 1.3.6.1.4.1.6527.3.1.2.64.1.2.1.2
The tmnxEthTunnelIfIndex indicates the tmnxPortPortID for the Ethernet Tunnel Group. The tmnxEthTunnelChassisIndex along with the tmnxEthTunnelIfIndex specifies the row in tmnxPortEntry that corresponds to the Ethernet Tunnel Group.
Status: current Access: read-only
OBJECT-TYPE    
  InterfaceIndexOrZero  

tmnxEthTunnelMgmtMemberIfIndex 1.3.6.1.4.1.6527.3.1.2.64.1.2.1.3
The tmnxEthTunnelMgmtMemberIfIndex indicates the tmnxEthTunnelMemberIfIndex of the Ethernet Tunnel Group member with which the Ethernet Tunnel Group port (tmnxEthTunnelIfIndex) inherits its port configurations. The management member is set to the first member added to the Ethernet Tunnel or the next higher member in the case of removing the first member from the group. If no members are configured for the group, the tmnxEthTunnelMgmtMemberIfIndex is set to zero (0).
Status: current Access: read-only
OBJECT-TYPE    
  InterfaceIndexOrZero  

tmnxEthTunnelActiveMembers 1.3.6.1.4.1.6527.3.1.2.64.1.2.1.4
The tmnxEthTunnelActiveMembers indicates which members are actively receiving and transmitting data for the Ethernet Tunnel Group.
Status: current Access: read-only
OBJECT-TYPE    
  TmnxEthTunnelMemberList  

tmnxEthTunnelRevertTimeCountDn 1.3.6.1.4.1.6527.3.1.2.64.1.2.1.5
The tmnxEthTunnelRevertTimeCountDn indicates the remaining time, in seconds, before the Ethernet Tunnel Group reverts back to the working member. A tmnxEthTunnelRevertTimeCountDn value of '0' indicates that the Ethernet Tunnel Group is not in a revertive wait state.
Status: current Access: read-only
OBJECT-TYPE    
  Unsigned32  

tmnxEthTunnelMbrTblLastChanged 1.3.6.1.4.1.6527.3.1.2.64.0.2
The tmnxEthTunnelMbrTblLastChanged indicates the time, since system startup, when a row in the tmnxEthTunnelMemberTable last changed.
Status: current Access: read-only
OBJECT-TYPE    
  TimeStamp  

tmnxEthTunnelMemberTable 1.3.6.1.4.1.6527.3.1.2.64.1.3
The tmnxEthTunnelMemberTable consists of the members associated with the corresponding tmnxEthTunnelConfigEntry.
Status: current Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    TmnxEthTunnelMemberEntry

tmnxEthTunnelMemberEntry 1.3.6.1.4.1.6527.3.1.2.64.1.3.1
The tmnxEthTunnelMemberEntry contains information pertaining to an individual member interface associated with a tmnxEthTunnelConfigEntry. Rows in this table are created and destroyed using the tmnxEthTunnelMemberRowStatus object.
Status: current Access: not-accessible
OBJECT-TYPE    
  TmnxEthTunnelMemberEntry  

tmnxEthTunnelMemberIndex 1.3.6.1.4.1.6527.3.1.2.64.1.3.1.1
The tmnxEthTunnelMemberIndex specifies the row index of the member.
Status: current Access: not-accessible
OBJECT-TYPE    
  TmnxEthTunnelMemberIndex 1..4294967295  

tmnxEthTunnelMemberRowStatus 1.3.6.1.4.1.6527.3.1.2.64.1.3.1.2
The tmnxEthTunnelMemberRowStatus controls the creation and deletion of row entries in the tmnxEthTunnelMemberTable.
Status: current Access: read-create
OBJECT-TYPE    
  RowStatus  

tmnxEthTunnelMemberTimeStamp 1.3.6.1.4.1.6527.3.1.2.64.1.3.1.3
The value of tmnxEthTunnelMemberTimeStamp indicates the time, since system startup, of the last change to this row.
Status: current Access: read-only
OBJECT-TYPE    
  TimeStamp  

tmnxEthTunnelMemberIfIndex 1.3.6.1.4.1.6527.3.1.2.64.1.3.1.4
The value of tmnxEthTunnelMemberIfIndex specifies the member's port tmnxPortPortID associated with the tmnxEthTunnelConfigEntry. Once specified, the tmnxEthTunnelMemberIfIndex can not be changed; the row must be destroyed and re-created.
Status: current Access: read-create
OBJECT-TYPE    
  InterfaceIndexOrZero  

tmnxEthTunnelMemberIfCtlTag 1.3.6.1.4.1.6527.3.1.2.64.1.3.1.5
The value of tmnxEthTunnelMemberIfCtlTag specifies the member's encapsulation. Once specified, the tmnxEthTunnelMemberIfCtlTag can not be changed; the row must be destroyed and re-created. The default value of all ones (0xFFFFFFFF) represents an invalid, unspecified, control tag.
Status: current Access: read-create
OBJECT-TYPE    
  TmnxEncapVal  

tmnxEthTunnelMemberDescription 1.3.6.1.4.1.6527.3.1.2.64.1.3.1.6
The value of tmnxEthTunnelMemberDescription specifies a detailed description of the Ethernet Tunnel member.
Status: current Access: read-create
OBJECT-TYPE    
  TItemDescription  

tmnxEthTunnelMemberAdminStatus 1.3.6.1.4.1.6527.3.1.2.64.1.3.1.7
The value of tmnxEthTunnelMemberAdminStatus specifies the administrative state of the member. 'outOfService (3)' specifies that the member will not partake in Tunnel Redundancy or load sharing.
Status: current Access: read-create
OBJECT-TYPE    
  TmnxAdminState  

tmnxEthTunnelMemberOperStatus 1.3.6.1.4.1.6527.3.1.2.64.1.3.1.8
The tmnxEthTunnelMemberOperStatus indicates the operational state of of the member. The tmnxEthTunnelMemberOperStatus supports the following two TmnxOperState values: inService (2) outOfService (3)
Status: current Access: read-only
OBJECT-TYPE    
  TmnxOperState  

tmnxEthTunnelMemberPrecedence 1.3.6.1.4.1.6527.3.1.2.64.1.3.1.9
The value of tmnxEthTunnelMemberPrecedence specifies the precedence level of the Member. When tmnxEthTunnelProtectionType of the group is set to 'g8031-1to1 (1)', only two precedence values are valid, and each member MUST have a different precedence. 0 - This is considered the primary member, or the working member. 1 - This is considered the secondary member, or the protection member. When tmnxEthTunnelProtectionType is set to the value 'loadsharing (2)' the precedence of all members should be the same.
Status: current Access: read-create
OBJECT-TYPE    
  Unsigned32 0..7  

tmnxEthTunnelAPSConfigs 1.3.6.1.4.1.6527.3.1.2.64.1.4
OBJECT IDENTIFIER    

tmnxEthTunnelApsTable 1.3.6.1.4.1.6527.3.1.2.64.1.4.1
The tmnxEthTunnelApsTable consists of APS configuration for Ethernet Tunnel Groups configured with a tmnxEthTunnelProtectionType set to 'g8031-1to1 (1)'.
Status: current Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    TmnxEthTunnelApsEntry

tmnxEthTunnelApsEntry 1.3.6.1.4.1.6527.3.1.2.64.1.4.1.1
The tmnxEthTunnelApsEntry contains APS information for an individual Ethernet Tunnel Group. Entries in the tmnxEthTunnelApsTable are created and destroyed by the system by changing the tmnxEthTunnelProtectionType object.
Status: current Access: not-accessible
OBJECT-TYPE    
  TmnxEthTunnelApsEntry  

tmnxEthTunnelApsRxPdu 1.3.6.1.4.1.6527.3.1.2.64.1.4.1.1.1
The value of tmnxEthTunnelApsRxPdu indicates the PDU last received on the Ethernet Tunnel Group.
Status: current Access: read-only
OBJECT-TYPE    
  TmnxEthTunnelApsPduType  

tmnxEthTunnelApsTxPdu 1.3.6.1.4.1.6527.3.1.2.64.1.4.1.1.2
The value of tmnxEthTunnelApsTxPdu indicates the PDU last transmitted on the Ethernet Tunnel Group.
Status: current Access: read-only
OBJECT-TYPE    
  TmnxEthTunnelApsPduType  

tmnxEthTunnelApsDefectStatus 1.3.6.1.4.1.6527.3.1.2.64.1.4.1.1.3
The value of tmnxEthTunnelApsDefectStatus indicates what defects are active on the Ethernet Tunnel Group. The Defects are defined as: dFopCM -- Configuration Mismatch dFopPM -- Provisioning Mismatch dFopNR -- Protocol No Response
Status: current Access: read-only
OBJECT-TYPE    
  BITS dFopCM(0), dFopPM(1), dFopNR(2)  

tmnxEthTunnelApsSwitchoverTime 1.3.6.1.4.1.6527.3.1.2.64.1.4.1.1.4
The value of tmnxEthTunnelApsSwitchoverTime indicates the time that the Ethernet Tunnel Group last experienced an APS switchover.
Status: current Access: read-only
OBJECT-TYPE    
  TimeStamp  

tmnxEthTunnelApsMemberTable 1.3.6.1.4.1.6527.3.1.2.64.1.4.2
The tmnxEthTunnelApsMemberTable consists of Ethernet Tunnel Group members which are associated with an Ethernet Tunnel Group where the tmnxEthTunnelProtectionType is set to 'g8031-1to1 (1)'.
Status: current Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    TmnxEthTunnelApsMemberEntry

tmnxEthTunnelApsMemberEntry 1.3.6.1.4.1.6527.3.1.2.64.1.4.2.1
The tmnxEthTunnelApsMemberEntry contains the APS information pertaining to an Ethernet Tunnel Group member. Entries in the tmnxEthTunnelApsMemberTable are created and destroyed by the system, when the Ethernet Tunnel Group object tmnxEthTunnelProtectionType is changed.
Status: current Access: not-accessible
OBJECT-TYPE    
  TmnxEthTunnelApsMemberEntry  

tmnxEthTunnelApsMemberActCount 1.3.6.1.4.1.6527.3.1.2.64.1.4.2.1.1
The value of tmnxEthTunnelApsMemberActCount indicates the number of times, since system startup, that the Ethernet Tunnel Group member has been active.
Status: current Access: read-only
OBJECT-TYPE    
  Counter32  

tmnxEthTunnelApsMemberActTime 1.3.6.1.4.1.6527.3.1.2.64.1.4.2.1.2
The value of tmnxEthTunnelApsMemberActTime indicates the accumulative time (in seconds) that the Ethernet Tunnel Group member has been active.
Status: current Access: read-only
OBJECT-TYPE    
  Counter32  

tmnxEthTunnelApsCommandTable 1.3.6.1.4.1.6527.3.1.2.64.1.4.3
The tmnxEthTunnelApsCommandTable consists of the one-shot action commands that effect state of Ethernet Tunnel APS configuration.
Status: current Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    TmnxEthTunnelApsCommandEntry

tmnxEthTunnelApsCommandEntry 1.3.6.1.4.1.6527.3.1.2.64.1.4.3.1
The tmnxEthTunnelApsCommandEntry contains the commands available to exist on an existing Ethernet Tunnel APS Group Member. Rows in this table are created and destroyed by the system.
Status: current Access: not-accessible
OBJECT-TYPE    
  TmnxEthTunnelApsCommandEntry  

tmnxEthTunnelApsCommandSwitch 1.3.6.1.4.1.6527.3.1.2.64.1.4.3.1.1
The value of tmnxEthTunnelApsCommandSwitch specifies the switch command to initiate on an Ethernet Tunnel APS Group. When read, this object returns the last command written or 'noCmd (0)' if no command has been written to this Ethernet Tunnel APS Group since initialization. The return of the last command written does not imply that this command is currently in effect. This request may be preempted by a higher priority local or remote request. In order to determine the current state of the group it is necessary to read the objects tmnxEthTunnelApsRxPdu and tmnxEthTunnelApsTxPdu. The value 'noCmd (0)' may not be used in a write command. The value 'clear (1)' clears all the switch commands listed below for the specified member. In addition, if tmnxEthTunnelRevertTime is a non-zero value (revertive mode) the active WTR (Wait To Restore) state is also cleared. The value 'lockoutOfSecondary (2)' prevents the primary (working) member from switching to the secondary (protection) member. The specified member should be the secondary member index, otherwise an inconsistentValue error is returned. The value 'forceSwitchPrimaryToSecondary (3)' switches the primary member to the secondary member. If the secondary member is specified an inconsistentValue error is returned. The value 'manualSwitchPrimaryToSecondary (4)' switches the specified primary member ot the secondary member. If the secondary member is specified an inconsistentValue error is returned. The value 'exercise (5)' exercises the protocol for a protection switch of the specified member by issuing an Exercise request for that member and checking the response on the APS member.
Status: current Access: read-write
OBJECT-TYPE    
  INTEGER noCmd(0), clear(1), lockoutOfSecondary(2), forceSwitchPrimaryToSecondary(3), manualSwitchPrimaryToSecondary(4), exercise(5)  

tmnxEthTunnelApsCommandExsResult 1.3.6.1.4.1.6527.3.1.2.64.1.4.3.1.2
The value of tmnxEthTunnelApsCommandExsResult indicates the result of the last 'excerise (5)' command issued from the tmnxEthTunnelApsCommandSwitch object. When this object returns 'unknown (4)' no 'excersie (5)' command has been written to this Ethernet Tunnel Group Member since initialization.
Status: current Access: read-only
OBJECT-TYPE    
  INTEGER passed(1), failed(2), preempted(3), unknown(4)  

tmnxEthTunnelLEConfigs 1.3.6.1.4.1.6527.3.1.2.64.1.5
OBJECT IDENTIFIER    

tmnxEthTunnelLETableChanged 1.3.6.1.4.1.6527.3.1.2.64.0.3
The value of tmnxEthTunnelLETableChanged indicates the time, since system startup, when a row in the tmnxEthTunnelLETable last changed.
Status: current Access: read-only
OBJECT-TYPE    
  TimeStamp  

tmnxEthTunnelLETable 1.3.6.1.4.1.6527.3.1.2.64.1.5.1
The tmnxEthTunnelLETable consists of the configuration for Ethernet Tunnel Groups that have tmnxEthTunnelProtectionType set to 'loadsharing (2)'.
Status: current Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    TmnxEthTunnelLEEntry

tmnxEthTunnelLEEntry 1.3.6.1.4.1.6527.3.1.2.64.1.5.1.1
The tmnxEthTunnelLEEntry contains the load sharing information pertaining to an Ethernet Tunnel Group. Entries in the tmnxEthTunnelLETable are created or destroyed by setting the tmnxEthTunnelProtectionType to or from 'loadsharing (2)'.
Status: current Access: not-accessible
OBJECT-TYPE    
  TmnxEthTunnelLEEntry  

tmnxEthTunnelLEAccessAdaptQos 1.3.6.1.4.1.6527.3.1.2.64.1.5.1.1.1
The value of tmnxEthTunnelLEAccessAdaptQos specifies how the Ethernet Tunnel Group SAP queue and virtual scheduler buffering and rate parameters are adapted over multiple active MDAs. link (1) - The Ethernet Tunnel Group will create the SAP queues and virtual schedulers with the actual parameters on each MDA. distribute(2) - Each MDA will receive a fraction of the SAP and scheduler parameters.
Status: current Access: read-write
OBJECT-TYPE    
  INTEGER link(1), distribute(2)  

tmnxEthTunnelLEPerFpIngQueueing 1.3.6.1.4.1.6527.3.1.2.64.1.5.1.1.2
The value of tmnxEthTunnelLEPerFpIngQueueing specifies whether a more efficient method of queue allocation for Ethernet Tunnel Group SAPs should be utilized. An 'inconsistentValue' error is returned if this object is set to a different value when there are existing members in the Ethernet Tunnel Group.
Status: current Access: read-write
OBJECT-TYPE    
  TruthValue  

tmnxEthTunnelLEMbrThreshold 1.3.6.1.4.1.6527.3.1.2.64.1.5.1.1.3
The value of tmnxEthTunnelLEMbrThreshold specifies the threshold for the Ethernet Tunnel Group. When a physical port member state changes and the number of operational physical port members is less than or equal to tmnxEthTunnelLEMbrThreshold, the Ethernet Tunnel Group is set operationally down. When the number of operational physical members become greater than tmnxEthTunnelLEMbrThreshold, the Ethernet Tunnel Group is set operationally up The value of zero specifies to bring the Ethernet Tunnel Group operationally down only when all members are operationally down, and bring the Ethernet Tunnel Group operationally up when at least one member is operationally up.
Status: current Access: read-write
OBJECT-TYPE    
  Unsigned32  

tmnxEthTunnelSAPConfigs 1.3.6.1.4.1.6527.3.1.2.64.1.6
OBJECT IDENTIFIER    

tmnxEthTunnelSAPMbrTblChanged 1.3.6.1.4.1.6527.3.1.2.64.0.4
The tmnxEthTunnelSAPMbrTblChanged indicates the time, since system startup, when a row in the tmnxEthTunnelSAPMemberTable last changed.
Status: current Access: read-only
OBJECT-TYPE    
  TimeStamp  

tmnxEthTunnelSAPMemberTable 1.3.6.1.4.1.6527.3.1.2.64.1.6.1
The tmnxEthTunnelSAPMemberTable consists of the configuration for Ethernet Tunnel Group members associated to SAPs.
Status: current Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    TmnxEthTunnelSAPMemberEntry

tmnxEthTunnelSAPMemberEntry 1.3.6.1.4.1.6527.3.1.2.64.1.6.1.1
The tmnxEthTunnelSAPMemberEntry contains the SAP information pertaining to an Ethernet Tunnel Group member. Entries in the tmnxEthTunnelSAPMemberTable are created and destroyed by setting the tmnxEthTunnelSAPMemberRowStatus object. Entries in this table corresponding to control SAPs, those with the index sapEncapValue set to 8191 (0x1FFF), are not writable. For a data SAP that is sharing the fate of a control SAP, these entries allow the configuration of the tag values for the corresponding path in the Ethernet Tunnel port.
Status: current Access: not-accessible
OBJECT-TYPE    
  TmnxEthTunnelSAPMemberEntry  

tmnxEthTunnelSAPMemberRowStatus 1.3.6.1.4.1.6527.3.1.2.64.1.6.1.1.1
The tmnxEthTunnelSAPMemberRowStatus controls the creation and deletion of row entries in the tmnxEthTunnelSAPMemberTable.
Status: current Access: read-create
OBJECT-TYPE    
  RowStatus  

tmnxEthTunnelSAPMemberTagValue 1.3.6.1.4.1.6527.3.1.2.64.1.6.1.1.2
The value of tmnxEthTunnelSAPMemberTagValue specifies the members' encapsulation for the SAP. The default value of all ones (0xFFFFFFFF) represents an invalid or unspecified tag.
Status: current Access: read-create
OBJECT-TYPE    
  TmnxEncapVal  

tmnxEthTunnelApsNotifications 1.3.6.1.4.1.6527.3.1.3.64.0.2
OBJECT IDENTIFIER    

tmnxEthTunnelApsCfgRaiseAlarm 1.3.6.1.4.1.6527.3.1.3.64.0.2.1
The tmnxEthTunnelApsCfgRaiseAlarm is generated when an Ethernet Tunnel Group working and protection configuration mismatch is detected, at the ETH layer, by detecting the reception of APS protocol from the working transport entity.
Status: current Access: read-create
NOTIFICATION-TYPE    

tmnxEthTunnelApsCfgClearAlarm 1.3.6.1.4.1.6527.3.1.3.64.0.2.2
The tmnxEthTunnelApsCfgClearAlarm is generated when an Ethernet Tunnel Group working and protection configuration mismatch is cleared.
Status: current Access: read-create
NOTIFICATION-TYPE    

tmnxEthTunnelApsPrvsnRaiseAlarm 1.3.6.1.4.1.6527.3.1.3.64.0.2.3
The tmnxEthTunnelApsPrvsnRaiseAlarm is generated when an Ethernet Tunnel Group provisioning mismatch is detected, at the ETH layer, by comparing A, B and D bits of the transmitted and received APS protocol. The provision mismatch state is considered as if there is a signal failure on the protection member. This ensures that the working member is kept as active member in the provision mismatch state.
Status: current Access: read-create
NOTIFICATION-TYPE    

tmnxEthTunnelApsPrvsnClearAlarm 1.3.6.1.4.1.6527.3.1.3.64.0.2.4
The tmnxEthTunnelApsPrvsnClearAlarm is generated when an Ethernet Tunnel Group provisioning mismatch is cleared.
Status: current Access: read-create
NOTIFICATION-TYPE    

tmnxEthTunnelApsNoRspRaiseAlarm 1.3.6.1.4.1.6527.3.1.3.64.0.2.5
The tmnxEthTunnelApsNoRspRaiseAlarm is generated when an Ethernet Tunnel Group experiences an incompletion of protection switching, at the ETH layer, by comparing the transmitted 'Requested Signal' values and the received 'Bridged Signal' in the APS protocol.
Status: current Access: read-create
NOTIFICATION-TYPE    

tmnxEthTunnelApsNoRspClearAlarm 1.3.6.1.4.1.6527.3.1.3.64.0.2.6
The tmnxEthTunnelApsNoRspClearAlarm is generated when an Ethernet Tunnel Group no longer experiences an incompletion of protection switching at the ETH layer.
Status: current Access: read-create
NOTIFICATION-TYPE    

tmnxEthTunnelApsSwitchoverAlarm 1.3.6.1.4.1.6527.3.1.3.64.0.2.7
The tmnxEthTunnelApsSwitchoverAlarm is generated when an Ethernet Tunnel Group experiences a member activity switchover. The tmnxEthTunnelMemberPrecedence always specifies the active member.
Status: current Access: read-create
NOTIFICATION-TYPE    

tmnxEthTunnelCompliance 1.3.6.1.4.1.6527.3.1.1.64.1.1
The compliance statement for revision 1.0 of TIMETRA-ETH-TUNNEL-MIB.
Status: obsolete Access: read-create
MODULE-COMPLIANCE    

tmnxEthTunnelV8v0Compliance 1.3.6.1.4.1.6527.3.1.1.64.1.2
The compliance statement for revision 2.0 of TIMETRA-ETH-TUNNEL-MIB.
Status: current Access: read-create
MODULE-COMPLIANCE    

tmnxEthTunnelTSGroups 1.3.6.1.4.1.6527.3.1.1.64.2.0
OBJECT IDENTIFIER    

tmnxEthTunnelTimeStampGroup 1.3.6.1.4.1.6527.3.1.1.64.2.0.1
The group of objects that track configuration changes for the maintenance of Ethernet Tunnels for the 7x50.
Status: current Access: read-create
OBJECT-GROUP    

tmnxEthTunnelTimeStampV8v0Group 1.3.6.1.4.1.6527.3.1.1.64.2.0.2
The group of objects that track configuration changes for the maintenance of Ethernet Tunnels for Release 8.0 of the 7x50.
Status: current Access: read-create
OBJECT-GROUP    

tmnxEthTunnelConfigGroups 1.3.6.1.4.1.6527.3.1.1.64.2.1
OBJECT IDENTIFIER    

tmnxEthTunnelBaseConfigGroup 1.3.6.1.4.1.6527.3.1.1.64.2.1.1
The group of objects for management of Ethernet Tunnel Group configurations for the 7x50.
Status: current Access: read-create
OBJECT-GROUP    

tmnxEthTunnelBaseConfigV8v0Group 1.3.6.1.4.1.6527.3.1.1.64.2.1.2
The group of objects for management of Ethernet Tunnel Group configurations for Release 8.0 of the 7x50.
Status: current Access: read-create
OBJECT-GROUP    

tmnxEthTunnelOperGroups 1.3.6.1.4.1.6527.3.1.1.64.2.2
OBJECT IDENTIFIER    

tmnxEthTunnelBaseOperGroup 1.3.6.1.4.1.6527.3.1.1.64.2.2.1
The group of objects for management of Ethernet Tunnel Group operations for the 7x50.
Status: current Access: read-create
OBJECT-GROUP    

tmnxEthTunnelMemberGroups 1.3.6.1.4.1.6527.3.1.1.64.2.3
OBJECT IDENTIFIER    

tmnxEthTunnelBaseMemberGroup 1.3.6.1.4.1.6527.3.1.1.64.2.3.1
The group of objects for management of Ethernet Tunnel Group Member configurations for the 7x50.
Status: current Access: read-create
OBJECT-GROUP    

tmnxEthTunnelAPSGroups 1.3.6.1.4.1.6527.3.1.1.64.2.4
OBJECT IDENTIFIER    

tmnxEthTunnelBaseAPSGroup 1.3.6.1.4.1.6527.3.1.1.64.2.4.1
The group of objects for management of Ethernet Tunnel Group APS configurations for the 7x50.
Status: current Access: read-create
OBJECT-GROUP    

tmnxEthTunnelBaseAPSV8v0Group 1.3.6.1.4.1.6527.3.1.1.64.2.4.2
The group of objects for management of Ethernet Tunnel Group APS configurations for the 7x50 in release 8.0.
Status: current Access: read-create
OBJECT-GROUP    

tmnxEthTunnelNotifyGroups 1.3.6.1.4.1.6527.3.1.1.64.2.5
OBJECT IDENTIFIER    

tmnxEthTunnelAPSNotifyGroup 1.3.6.1.4.1.6527.3.1.1.64.2.5.1
The group of notifications supporting the management of Ethernet Tunnel Group configuration for the 7x50.
Status: current Access: read-create
NOTIFICATION-GROUP    

tmnxEthTunnelSAPGroups 1.3.6.1.4.1.6527.3.1.1.64.2.6
OBJECT IDENTIFIER    

tmnxEthTunnelSAPMemberGroup 1.3.6.1.4.1.6527.3.1.1.64.2.6.1
The group of objects added in Release 8.0 to support configuration and maintenance of Ethernet Tunnel Groups on SAPs for the 7x50.
Status: current Access: read-create
OBJECT-GROUP    

tmnxEthTunnelLEGroups 1.3.6.1.4.1.6527.3.1.1.64.2.7
OBJECT IDENTIFIER    

tmnxEthTunnelLEGroup 1.3.6.1.4.1.6527.3.1.1.64.2.7.1
The group of objects added in Release 8.0 to support configuration and maintenance of Ethernet Tunnel Groups for loadsharing (LAG) for the 7x50.
Status: current Access: read-create
OBJECT-GROUP