TIMETRA-DIAMETER-MIB

File: TIMETRA-DIAMETER-MIB.mib (70060 bytes)

Imported modules

SNMPv2-SMI	SNMPv2-CONF	SNMPv2-TC
TIMETRA-GLOBAL-MIB	TIMETRA-TC-MIB	INET-ADDRESS-MIB

Imported symbols

MODULE-IDENTITY	OBJECT-TYPE	NOTIFICATION-TYPE
Unsigned32	Counter32	MODULE-COMPLIANCE
OBJECT-GROUP	NOTIFICATION-GROUP	RowStatus
TimeStamp	TruthValue	TEXTUAL-CONVENTION
DisplayString	timetraSRMIBModules	tmnxSRObjs
tmnxSRNotifyPrefix	tmnxSRConfs	TNamedItem
TItemDescription	TmnxVRtrID	TmnxSubNasPortSuffixType
TmnxSubNasPortPrefixType	InetAddressType	InetAddress

Defined Types

TmnxDiameterAdminStatus
The TmnxDiameterAdminStatus data type is an enumerated integer that describes the values used to identify the administrative state.
TEXTUAL-CONVENTION
	INTEGER	enabled(1), disabled(2)

TmnxDiamPeerTransportProt
The TmnxDiamPeerTransportProt data type is an enumerated integer that describes the different transport protocols that can be used to setup a DIAMETER connection.
TEXTUAL-CONVENTION
	INTEGER	tcp(1)

TmnxDiamCcFailureHndlng
The TmnxDiamCcFailureHndlng data type is an enumerated integer that describes the different actions that can be taken after a DCCA (Diameter Credit Control Application) session failure has occured.
TEXTUAL-CONVENTION
	INTEGER	terminate(1), continue(2), retryAndTerminate(3)

TmnxDiamDccaApplicationType
The TmnxDiamDccaApplicationType data type is an enumerated integer that identifies the different DCCA (Diameter Credit Control Application) application types. A particular value of TmnxDiamDccaApplicationType is associated with a set of values for the Authentication-Application-Id AVP (Attribute Value Pair) in Diameter messages.
TEXTUAL-CONVENTION
	INTEGER	vfDccaV2(1), gx(2)

TmnxDiamPlcyVendorSupportType
The TmnxDiamPlcyVendorSupportType data type is an enumerated integer that describes which vendor specific attributes are used in DCCA sessions.
TEXTUAL-CONVENTION
	INTEGER	vodafone(1), threeGpp(2)

TmnxDiamPlcyDccaAvpOriginType
The TmnxDiamPlcyDccaAvpOriginType data type is an enumerated integer that describes the origin of th information to send in the AVP.
TEXTUAL-CONVENTION
	INTEGER	subscriberId(1), circuitId(2), imsi(3), msisdn(4), imei(5)

TmnxDiameterPlcyEntry
SEQUENCE
	tmnxDiamPlcyName	TNamedItem
	tmnxDiamPlcyRowStatus	RowStatus
	tmnxDiamPlcyLastMgmtChange	TimeStamp
	tmnxDiamPlcyDescription	TItemDescription
	tmnxDiamPlcyOriginHost	DisplayString
	tmnxDiamPlcyOriginRealm	DisplayString
	tmnxDiamPlcyRouter	TmnxVRtrID
	tmnxDiamPlcySourceAddrType	InetAddressType
	tmnxDiamPlcySourceAddr	InetAddress
	tmnxDiamPlcyWatchdogTimer	Unsigned32
	tmnxDiamPlcyConnectionTimer	Unsigned32
	tmnxDiamPlcyTransactionTimer	Unsigned32
	tmnxDiamPlcyVendorSupport	TmnxDiamPlcyVendorSupportType

TmnxDiameterPlcyPeerEntry
SEQUENCE
	tmnxDiamPlcyPeerName	TNamedItem
	tmnxDiamPlcyPeerRowStatus	RowStatus
	tmnxDiamPlcyPeerLastMgmtChange	TimeStamp
	tmnxDiamPlcyPeerAdminState	TmnxDiameterAdminStatus
	tmnxDiamPlcyPeerAddrType	InetAddressType
	tmnxDiamPlcyPeerAddr	InetAddress
	tmnxDiamPlcyPeerTransportProt	TmnxDiamPeerTransportProt
	tmnxDiamPlcyPeerTransportPort	Unsigned32
	tmnxDiamPlcyPeerDestHost	DisplayString
	tmnxDiamPlcyPeerDestRealm	DisplayString
	tmnxDiamPlcyPeerWatchdogTimer	Unsigned32
	tmnxDiamPlcyPeerConnectionTimer	Unsigned32
	tmnxDiamPlcyPeerTransactTimer	Unsigned32
	tmnxDiamPlcyPeerPreference	Unsigned32

TmnxDiamPlcyPeerInfoEntry
SEQUENCE
	tmnxDiamPeerPsmState	INTEGER
	tmnxDiamPeerConnectionSuspended	TruthValue
	tmnxDiamPeerCooldownSeqStage	INTEGER
	tmnxDiamPeerOrder	Unsigned32
	tmnxDiamPeerPrimarySecondary	INTEGER
	tmnxDiamPeerTcTimerTimeLeft	Unsigned32
	tmnxDiamPeerTtTimerTimeLeft	Unsigned32
	tmnxDiamPeerTwTimerTimeLeft	Unsigned32
	tmnxDiamPeerWatchdogAlgActive	TruthValue
	tmnxDiamPeerWatchdogAnswPending	TruthValue
	tmnxDiamPeerCooldownSeqPending	TruthValue
	tmnxDiamPeerCooldownSeqActive	TruthValue
	tmnxDiamPeerPeerRemovalPending	TruthValue

TmnxDiamPlcyPeerStatsEntry
SEQUENCE
	tmnxDiamPeerStatsLastClearTime	TimeStamp
	tmnxDiamPeerStCiTcpSendFailed	Counter32
	tmnxDiamPeerStCiDiamRxDropCnt	Counter32
	tmnxDiamPeerStCiDiamTxReqs	Counter32
	tmnxDiamPeerStCiDiamRxResps	Counter32
	tmnxDiamPeerStCiPendMsgsPMQ	Counter32
	tmnxDiamPeerStCiReqTimeoutsPMQ	Counter32
	tmnxDiamPeerStSiTcpSendFailed	Counter32
	tmnxDiamPeerStSiDiamRxDropCnt	Counter32
	tmnxDiamPeerStSiDiamRxReqs	Counter32
	tmnxDiamPeerStSiDiamTxResps	Counter32
	tmnxDiamPeerStErrHdlDiamTxErrCnt	Counter32
	tmnxDiamPeerStErrHdlDiamRxErrCnt	Counter32
	tmnxDiamPeerStCcrInitialTx	Counter32
	tmnxDiamPeerStCcaInitialRx	Counter32
	tmnxDiamPeerStCcrUpdateTx	Counter32
	tmnxDiamPeerStCcaUpdateRx	Counter32
	tmnxDiamPeerStCcrTerminateTx	Counter32
	tmnxDiamPeerStCcaTerminateRx	Counter32
	tmnxDiamPeerStCerTx	Counter32
	tmnxDiamPeerStCeaRx	Counter32
	tmnxDiamPeerStWdrTx	Counter32
	tmnxDiamPeerStWdaRx	Counter32
	tmnxDiamPeerStWdrRx	Counter32
	tmnxDiamPeerStWdaTx	Counter32
	tmnxDiamPeerStAsrRx	Counter32
	tmnxDiamPeerStAsaTx	Counter32
	tmnxDiamPeerStRarRx	Counter32
	tmnxDiamPeerStRaaTx	Counter32
	tmnxDiamPeerStDprTx	Counter32
	tmnxDiamPeerStDpaRx	Counter32
	tmnxDiamPeerStDprRx	Counter32
	tmnxDiamPeerStDpaTx	Counter32

TmnxDiameterPlcyDccaEntry
SEQUENCE
	tmnxDiamPlcyDccaLastMgmtChange	TimeStamp
	tmnxDiamPlcyDccaFailover	TruthValue
	tmnxDiamPlcyDccaFailureHndlng	TmnxDiamCcFailureHndlng
	tmnxDiamPlcyDccaTxTimer	Unsigned32
	tmnxDiamPlcyDccaAvpServCntxtId	DisplayString
	tmnxDiamPlcyDccaAvpCldStationId	DisplayString
	tmnxDiamPlcyDccaAvpRadiusUsrNme	TruthValue
	tmnxDiamPlcyDccaAvpSubIdOrg	TmnxDiamPlcyDccaAvpOriginType
	tmnxDiamPlcyDccaAvpSubIdType	INTEGER
	tmnxDiamPlcyDccaAvpNasP	TruthValue
	tmnxDiamPlcyDccaAvpNasPPfixType	TmnxSubNasPortPrefixType
	tmnxDiamPlcyDccaAvpNasPPfixStr	DisplayString
	tmnxDiamPlcyDccaAvpNasPSfixType	TmnxSubNasPortSuffixType
	tmnxDiamPlcyDccaAvpNasPType	TruthValue
	tmnxDiamPlcyDccaAvpImsiOrg	TmnxDiamPlcyDccaAvpOriginType
	tmnxDiamPlcyDccaApplicationType	TmnxDiamDccaApplicationType
	tmnxDiamPlcyDccaMaxPendingReq	Unsigned32
	tmnxDiamPlcyDccaTxRetryLimit	Unsigned32
	tmnxDiamPlcyDccaOutOfCreditRep	INTEGER

Defined Values

timetraDiameterMIBModule		1.3.6.1.4.1.6527.1.1.3.58
This document is the SNMP MIB module to manage and provision DIAMETER on the Alcatel-Lucent SROS device. Copyright 2008-2012 Alcatel-Lucent. All rights reserved. Reproduction of this document is authorized on the condition that the foregoing copyright notice is included. This SNMP MIB module (Specification) embodies Alcatel-Lucent's proprietary intellectual property. Alcatel-Lucent retains all title and ownership in the Specification, including any revisions. Alcatel-Lucent grants all interested parties a non-exclusive license to use and distribute an unmodified copy of this Specification in connection with management of Alcatel-Lucent products, and without fee, provided this copyright notice and license appear on all copies. This Specification is supplied 'as is', and Alcatel-Lucent makes no warranty, either express or implied, as to the use, operation, condition, or performance of the Specification.
MODULE-IDENTITY

tmnxDiameter		1.3.6.1.4.1.6527.3.1.2.58
OBJECT IDENTIFIER

tmnxDiameterBaseObjects		1.3.6.1.4.1.6527.3.1.2.58.1
OBJECT IDENTIFIER

tmnxDiameterDccaObjects		1.3.6.1.4.1.6527.3.1.2.58.2
OBJECT IDENTIFIER

tmnxDiameterNotificationObjs		1.3.6.1.4.1.6527.3.1.2.58.100
OBJECT IDENTIFIER

tmnxDiameterConformance		1.3.6.1.4.1.6527.3.1.1.58
OBJECT IDENTIFIER

tmnxDiameterCompliances		1.3.6.1.4.1.6527.3.1.1.58.1
OBJECT IDENTIFIER

tmnxDiameterGroups		1.3.6.1.4.1.6527.3.1.1.58.2
OBJECT IDENTIFIER

tmnxDiameterNotifyPrefix		1.3.6.1.4.1.6527.3.1.3.58
OBJECT IDENTIFIER

tmnxDiameterNotifications		1.3.6.1.4.1.6527.3.1.3.58.0
OBJECT IDENTIFIER

tmnxDiameterPlcyTableLastChngd		1.3.6.1.4.1.6527.3.1.2.58.1.1
The value of tmnxDiameterPlcyTableLastChngd indicates the sysUpTime at the time of the most recent management-initiated change to the tmnxDiameterPlcyTable.
Status: current	Access: read-only
OBJECT-TYPE
	TimeStamp

tmnxDiameterPlcyTable		1.3.6.1.4.1.6527.3.1.2.58.1.2
The tmnxDiameterPlcyTable has an entry for each DIAMETER policy configured in the system.
Status: current	Access: not-accessible
OBJECT-TYPE
	SEQUENCE OF
		TmnxDiameterPlcyEntry

tmnxDiameterPlcyEntry		1.3.6.1.4.1.6527.3.1.2.58.1.2.1
Each row entry represents a DIAMETER policy configured in the system. Entries can be created and deleted via SNMP SET operations on the object tmnxDiamPlcyRowStatus.
Status: current	Access: not-accessible
OBJECT-TYPE
	TmnxDiameterPlcyEntry

tmnxDiamPlcyName		1.3.6.1.4.1.6527.3.1.2.58.1.2.1.1
The value of tmnxDiamPlcyName specifies the name of the DIAMETER policy.
Status: current	Access: not-accessible
OBJECT-TYPE
	TNamedItem

tmnxDiamPlcyRowStatus		1.3.6.1.4.1.6527.3.1.2.58.1.2.1.2
The value of tmnxDiamPlcyRowStatus controls the creation and deletion of rows in this table.
Status: current	Access: read-create
OBJECT-TYPE
	RowStatus

tmnxDiamPlcyLastMgmtChange		1.3.6.1.4.1.6527.3.1.2.58.1.2.1.3
The value of tmnxDiamPlcyLastMgmtChange indicates the sysUpTime at the time of the most recent management-initiated change to this table row.
Status: current	Access: read-only
OBJECT-TYPE
	TimeStamp

tmnxDiamPlcyDescription		1.3.6.1.4.1.6527.3.1.2.58.1.2.1.4
The value of tmnxDiamPlcyDescription specifies the user provided description of this DIAMETER policy.
Status: current	Access: read-create
OBJECT-TYPE
	TItemDescription

tmnxDiamPlcyOriginHost		1.3.6.1.4.1.6527.3.1.2.58.1.2.1.5
The value of tmnxDiamPlcyOriginHost specifies the Origin-Host AVP (Attribute Value Pair) used by this DIAMETER policy.
Status: current	Access: read-create
OBJECT-TYPE
	DisplayString	Size(0..80)

tmnxDiamPlcyOriginRealm		1.3.6.1.4.1.6527.3.1.2.58.1.2.1.6
The value of tmnxDiamPlcyOriginRealm specifies the Origin-Realm AVP (Attribute Value Pair) used by this DIAMETER policy.
Status: current	Access: read-create
OBJECT-TYPE
	DisplayString	Size(0..80)

tmnxDiamPlcyRouter		1.3.6.1.4.1.6527.3.1.2.58.1.2.1.7
The value of tmnxDiamPlcyRouter specifies the virtual router in which the DIAMETER connection(s) will be established by this DIAMETER policy.
Status: current	Access: read-create
OBJECT-TYPE
	TmnxVRtrID

tmnxDiamPlcySourceAddrType		1.3.6.1.4.1.6527.3.1.2.58.1.2.1.8
The value of tmnxDiamPlcySourceAddrType specifies the type of address contained in tmnxDiamPlcySourceAddr.
Status: current	Access: read-create
OBJECT-TYPE
	InetAddressType

tmnxDiamPlcySourceAddr		1.3.6.1.4.1.6527.3.1.2.58.1.2.1.9
The value of tmnxDiamPlcySourceAddr specifies the source IP address used to setup DIAMETER connection in this DIAMETER policy.
Status: current	Access: read-create
OBJECT-TYPE
	InetAddress	Size(0\|4)

tmnxDiamPlcyWatchdogTimer		1.3.6.1.4.1.6527.3.1.2.58.1.2.1.10
The value of tmnxDiamPlcyWatchdogTimer specifies the device watchdog timer (TW) (in seconds) used on all connections by this DIAMETER policy.
Status: current	Access: read-create
OBJECT-TYPE
	Unsigned32	1..1000

tmnxDiamPlcyConnectionTimer		1.3.6.1.4.1.6527.3.1.2.58.1.2.1.11
The value of tmnxDiamPlcyConnectionTimer specifies the connection timer (TC) (in seconds) used by this DIAMETER policy. It defines the time the systems waits before attempting to reconnect to a peer after the connection was lost.
Status: current	Access: read-create
OBJECT-TYPE
	Unsigned32	1..1000

tmnxDiamPlcyTransactionTimer		1.3.6.1.4.1.6527.3.1.2.58.1.2.1.12
The value of tmnxDiamPlcyTransactionTimer specifies the transaction timer (in seconds) used by this DIAMETER policy. This timer defines how long the system will wait for an answer from the peer after sending a request.
Status: current	Access: read-create
OBJECT-TYPE
	Unsigned32	1..1000

tmnxDiamPlcyVendorSupport		1.3.6.1.4.1.6527.3.1.2.58.1.2.1.13
The value of tmnxDiamPlcyVendorSupport specifies which vendor specific attributes are used in DCCA sessions for this DIAMETER policy.
Status: current	Access: read-create
OBJECT-TYPE
	TmnxDiamPlcyVendorSupportType

tmnxDiamPlcyPeerTableLastChngd		1.3.6.1.4.1.6527.3.1.2.58.1.3
The value of tmnxDiamPlcyPeerTableLastChngd indicates the sysUpTime at the time of the most recent management-initiated change to the tmnxDiameterPlcyPeerTable.
Status: current	Access: read-only
OBJECT-TYPE
	TimeStamp

tmnxDiameterPlcyPeerTable		1.3.6.1.4.1.6527.3.1.2.58.1.4
The tmnxDiameterPlcyPeerTable has an entry for each peer defined in a DIAMETER policy configured in the system.
Status: current	Access: not-accessible
OBJECT-TYPE
	SEQUENCE OF
		TmnxDiameterPlcyPeerEntry

tmnxDiameterPlcyPeerEntry		1.3.6.1.4.1.6527.3.1.2.58.1.4.1
Each row entry represents a peer configured in a DIAMETER policy configured in the system. Entries can be created and deleted via SNMP SET operations on the object tmnxDiamPlcyPeerRowStatus.
Status: current	Access: not-accessible
OBJECT-TYPE
	TmnxDiameterPlcyPeerEntry

tmnxDiamPlcyPeerName		1.3.6.1.4.1.6527.3.1.2.58.1.4.1.1
The value of tmnxDiamPlcyPeerName specifies the name of the peer within a DIAMETER policy.
Status: current	Access: not-accessible
OBJECT-TYPE
	TNamedItem

tmnxDiamPlcyPeerRowStatus		1.3.6.1.4.1.6527.3.1.2.58.1.4.1.2
The value of tmnxDiamPlcyPeerRowStatus controls the creation and deletion of rows in this table.
Status: current	Access: read-create
OBJECT-TYPE
	RowStatus

tmnxDiamPlcyPeerLastMgmtChange		1.3.6.1.4.1.6527.3.1.2.58.1.4.1.3
The value of tmnxDiamPlcyPeerLastMgmtChange indicates the sysUpTime at the time of the most recent management-initiated change to this table row.
Status: current	Access: read-only
OBJECT-TYPE
	TimeStamp

tmnxDiamPlcyPeerAdminState		1.3.6.1.4.1.6527.3.1.2.58.1.4.1.4
The value of the object tmnxDiamPlcyPeerAdminState specifies the administrative state of the DIAMETER Policy peer.
Status: current	Access: read-create
OBJECT-TYPE
	TmnxDiameterAdminStatus

tmnxDiamPlcyPeerAddrType		1.3.6.1.4.1.6527.3.1.2.58.1.4.1.5
The value of tmnxDiamPlcyPeerAddrType specifies the type of address contained in tmnxDiamPlcyPeerAddr.
Status: current	Access: read-create
OBJECT-TYPE
	InetAddressType

tmnxDiamPlcyPeerAddr		1.3.6.1.4.1.6527.3.1.2.58.1.4.1.6
The value of tmnxDiamPlcyPeerAddr specifies the IP address of this DIAMETER policy peer.
Status: current	Access: read-create
OBJECT-TYPE
	InetAddress	Size(0\|4)

tmnxDiamPlcyPeerTransportProt		1.3.6.1.4.1.6527.3.1.2.58.1.4.1.7
The value of tmnxDiamPlcyPeerTransportProt specifies the transport protocol used towards this DIAMETER policy peer.
Status: current	Access: read-create
OBJECT-TYPE
	TmnxDiamPeerTransportProt

tmnxDiamPlcyPeerTransportPort		1.3.6.1.4.1.6527.3.1.2.58.1.4.1.8
The value of tmnxDiamPlcyPeerTransportPort specifies the transport protocol port number used towards this DIAMETER policy peer.
Status: current	Access: read-create
OBJECT-TYPE
	Unsigned32	1..65535

tmnxDiamPlcyPeerDestHost		1.3.6.1.4.1.6527.3.1.2.58.1.4.1.9
The value of tmnxDiamPlcyPeerDestHost specifies the Destination-Host AVP used by this DIAMETER policy peer.
Status: current	Access: read-create
OBJECT-TYPE
	DisplayString	Size(0..80)

tmnxDiamPlcyPeerDestRealm		1.3.6.1.4.1.6527.3.1.2.58.1.4.1.10
The value of tmnxDiamPlcyPeerDestRealm specifies the Destination-Realm AVP used by this DIAMETER policy peer.
Status: current	Access: read-create
OBJECT-TYPE
	DisplayString	Size(0..80)

tmnxDiamPlcyPeerWatchdogTimer		1.3.6.1.4.1.6527.3.1.2.58.1.4.1.11
The value of tmnxDiamPlcyPeerWatchdogTimer specifies the device watchdog timer (in seconds) used by this DIAMETER policy peer. A value '0' will cause the peer to use the watchdog timer defined at DIAMETER base level (tmnxDiamPlcyWatchdogTimer).
Status: current	Access: read-create
OBJECT-TYPE
	Unsigned32	0 \| 1..1000

tmnxDiamPlcyPeerConnectionTimer		1.3.6.1.4.1.6527.3.1.2.58.1.4.1.12
The value of tmnxDiamPlcyPeerConnectionTimer specifies the device connection timer (in seconds) used by this DIAMETER policy peer. A value '0' will cause the peer to use the connection timer defined at DIAMETER base level (tmnxDiamPlcyConnectionTimer).
Status: current	Access: read-create
OBJECT-TYPE
	Unsigned32	0 \| 1..1000

tmnxDiamPlcyPeerTransactTimer		1.3.6.1.4.1.6527.3.1.2.58.1.4.1.13
The value of tmnxDiamPlcyPeerTransactTimer specifies the device transaction timer (in seconds) used by this DIAMETER policy peer. A value '0' will cause the peer to use the transaction timer defined at DIAMETER base level (tmnxDiamPlcyTransactionTimer).
Status: current	Access: read-create
OBJECT-TYPE
	Unsigned32	0 \| 1..1000

tmnxDiamPlcyPeerPreference		1.3.6.1.4.1.6527.3.1.2.58.1.4.1.14
The value of tmnxDiamPlcyPeerPreference specifies the preference given to this DIAMETER policy peer with respect to the other peers associated with this DIAMETER policy. If multiple peers are available for this policy, only the available peer with the highest preference will be used. If multiple peers with the same preference are available, one of them will be used. The highest preference is specified by the value '1'.
Status: current	Access: read-create
OBJECT-TYPE
	Unsigned32	1..100

tmnxDiamPlcyPeerInfoTable		1.3.6.1.4.1.6527.3.1.2.58.1.5
The tmnxDiamPlcyPeerInfoTable contains detailed runtime information about the peers defined in a DIAMETER policy.
Status: current	Access: not-accessible
OBJECT-TYPE
	SEQUENCE OF
		TmnxDiamPlcyPeerInfoEntry

tmnxDiamPlcyPeerInfoEntry		1.3.6.1.4.1.6527.3.1.2.58.1.5.1
Each conceptual row contains detailed runtime information about a peer defined in a DIAMETER policy. Entries in this table are created and removed automatically by the system
Status: current	Access: not-accessible
OBJECT-TYPE
	TmnxDiamPlcyPeerInfoEntry

tmnxDiamPeerPsmState		1.3.6.1.4.1.6527.3.1.2.58.1.5.1.1
The value of tmnxDiamPeerPsmState indicates the current state of the DIAMETER peer's state machine.
Status: current	Access: read-only
OBJECT-TYPE
	INTEGER	closed(0), wait-conn-ack(1), wait-i-cea(2), i-open(3), closing(4)

tmnxDiamPeerConnectionSuspended		1.3.6.1.4.1.6527.3.1.2.58.1.5.1.2
The value of tmnxDiamPeerConnectionSuspended indicates whether the peer's DIAMETER connection that is in I-Open state has been temporarily put on suspension.
Status: current	Access: read-only
OBJECT-TYPE
	TruthValue

tmnxDiamPeerCooldownSeqStage		1.3.6.1.4.1.6527.3.1.2.58.1.5.1.3
While the value of tmnxDiamPeerCooldownSeqActive is 'true', the value of tmnxDiamPeerCooldownSeqStage indicates the current stage of the cooling down sequence.
Status: current	Access: read-only
OBJECT-TYPE
	INTEGER	stage1(0), stage2(1), stage3(2)

tmnxDiamPeerOrder		1.3.6.1.4.1.6527.3.1.2.58.1.5.1.4
The value of tmnxDiamPeerOrder indicates the runtime order of the DIAMETER policy's peers. It is determined both by the configuration level preference and other runtime conditions. A value of zero indicates this field is currently not applicable for this peer.
Status: current	Access: read-only
OBJECT-TYPE
	Unsigned32

tmnxDiamPeerPrimarySecondary		1.3.6.1.4.1.6527.3.1.2.58.1.5.1.5
The value of tmnxDiamPeerPrimarySecondary indicates whether the DIAMETER peer figures as primary or secondary peer in its policy.
Status: current	Access: read-only
OBJECT-TYPE
	INTEGER	none(0), primary(1), secondary(2)

tmnxDiamPeerTcTimerTimeLeft		1.3.6.1.4.1.6527.3.1.2.58.1.5.1.6
The value of tmnxDiamPeerTcTimerTimeLeft indicates the current countdown progress of the DIAMETER peer's connection timer.
Status: current	Access: read-only
OBJECT-TYPE
	Unsigned32

tmnxDiamPeerTtTimerTimeLeft		1.3.6.1.4.1.6527.3.1.2.58.1.5.1.7
The value of tmnxDiamPeerTtTimerTimeLeft indicates the current countdown progress of the DIAMETER peer's transaction timer.
Status: current	Access: read-only
OBJECT-TYPE
	Unsigned32

tmnxDiamPeerTwTimerTimeLeft		1.3.6.1.4.1.6527.3.1.2.58.1.5.1.8
The value of tmnxDiamPeerTwTimerTimeLeft indicates the current countdown progress of the DIAMETER peer's watchdog timer.
Status: current	Access: read-only
OBJECT-TYPE
	Unsigned32

tmnxDiamPeerWatchdogAlgActive		1.3.6.1.4.1.6527.3.1.2.58.1.5.1.9
The value of tmnxDiamPeerWatchdogAlgActive indicates whether the DIAMETER application-layer watchdog algorithm is currently running.
Status: current	Access: read-only
OBJECT-TYPE
	TruthValue

tmnxDiamPeerWatchdogAnswPending		1.3.6.1.4.1.6527.3.1.2.58.1.5.1.10
The value of tmnxDiamPeerWatchdogAnswPending indicates whether reception of a DIAMETER Device Watchdog Answer (DWA) is expected for a corresponding Device Watchdog Request (DWR) waiting in the Pending Message Queue (PMQ).
Status: current	Access: read-only
OBJECT-TYPE
	TruthValue

tmnxDiamPeerCooldownSeqPending		1.3.6.1.4.1.6527.3.1.2.58.1.5.1.11
The value of tmnxDiamPeerCooldownSeqPending indicates whether the DIAMETER peer's connection manages to get in a non-suspended I-Open state.
Status: current	Access: read-only
OBJECT-TYPE
	TruthValue

tmnxDiamPeerCooldownSeqActive		1.3.6.1.4.1.6527.3.1.2.58.1.5.1.12
The value of tmnxDiamPeerCooldownSeqActive indicates whether the DIAMETER Cooldown Sequence is currently running.
Status: current	Access: read-only
OBJECT-TYPE
	TruthValue

tmnxDiamPeerPeerRemovalPending		1.3.6.1.4.1.6527.3.1.2.58.1.5.1.13
The value of tmnxDiamPeerPeerRemovalPending indicates whether the execution of a DIAMETER peer's removal is still pending until the disconnect-peer roundtrip has finished.
Status: current	Access: read-only
OBJECT-TYPE
	TruthValue

tmnxDiamPlcyPeerStatsTable		1.3.6.1.4.1.6527.3.1.2.58.1.6
The tmnxDiamPlcyPeerStatsTable contains detailed statistics about the peers defined in a DIAMETER policy.
Status: current	Access: not-accessible
OBJECT-TYPE
	SEQUENCE OF
		TmnxDiamPlcyPeerStatsEntry

tmnxDiamPlcyPeerStatsEntry		1.3.6.1.4.1.6527.3.1.2.58.1.6.1
Each conceptual row contains detailed statistics about a peer defined in a DIAMETER policy. Entries in this table are created and removed automatically by the system
Status: current	Access: not-accessible
OBJECT-TYPE
	TmnxDiamPlcyPeerStatsEntry

tmnxDiamPeerStatsLastClearTime		1.3.6.1.4.1.6527.3.1.2.58.1.6.1.1
The value of tmnxDiamPeerStatsLastClearTime indicates the sysUpTime when the counters of this row were last reset. A value of zero for this object indicates that the counters have not been reset since the system has last been initialized.
Status: current	Access: read-only
OBJECT-TYPE
	TimeStamp

tmnxDiamPeerStCiTcpSendFailed		1.3.6.1.4.1.6527.3.1.2.58.1.6.1.2
The value of tmnxDiamPeerStCiTcpSendFailed indicates client initiated roundtrip DIAMETER statistics regarding the number of TCP send failures.
Status: current	Access: read-only
OBJECT-TYPE
	Counter32

tmnxDiamPeerStCiDiamRxDropCnt		1.3.6.1.4.1.6527.3.1.2.58.1.6.1.3
The value of tmnxDiamPeerStCiDiamRxDropCnt indicates client initiated roundtrip DIAMETER statistics regarding the number of dropped response messages upon reception from server.
Status: current	Access: read-only
OBJECT-TYPE
	Counter32

tmnxDiamPeerStCiDiamTxReqs		1.3.6.1.4.1.6527.3.1.2.58.1.6.1.4
The value of tmnxDiamPeerStCiDiamTxReqs indicates client initiated roundtrip DIAMETER statistics regarding the number of request messages sent to server.
Status: current	Access: read-only
OBJECT-TYPE
	Counter32

tmnxDiamPeerStCiDiamRxResps		1.3.6.1.4.1.6527.3.1.2.58.1.6.1.5
The value of tmnxDiamPeerStCiDiamRxResps indicates client initiated roundtrip DIAMETER statistics regarding the number of response messages received from server.
Status: current	Access: read-only
OBJECT-TYPE
	Counter32

tmnxDiamPeerStCiPendMsgsPMQ		1.3.6.1.4.1.6527.3.1.2.58.1.6.1.6
The value of tmnxDiamPeerStCiPendMsgsPMQ indicates client initiated roundtrip DIAMETER statistics regarding the number of request messages in the Pending Message Queue waiting to be matched with corresponding response messages from the server.
Status: current	Access: read-only
OBJECT-TYPE
	Counter32

tmnxDiamPeerStCiReqTimeoutsPMQ		1.3.6.1.4.1.6527.3.1.2.58.1.6.1.7
The value of tmnxDiamPeerStCiReqTimeoutsPMQ indicates client initiated roundtrip DIAMETER statistics regarding the number of request messages that were removed from the Pending Message Queue due to a match timeout.
Status: current	Access: read-only
OBJECT-TYPE
	Counter32

tmnxDiamPeerStSiTcpSendFailed		1.3.6.1.4.1.6527.3.1.2.58.1.6.1.8
The value of tmnxDiamPeerStSiTcpSendFailed indicates client initiated roundtrip DIAMETER statistics regarding the number of TCP send failures.
Status: current	Access: read-only
OBJECT-TYPE
	Counter32

tmnxDiamPeerStSiDiamRxDropCnt		1.3.6.1.4.1.6527.3.1.2.58.1.6.1.9
The value of tmnxDiamPeerStSiDiamRxDropCnt indicates client initiated roundtrip DIAMETER statistics regarding the number of dropped request messages upon reception from server.
Status: current	Access: read-only
OBJECT-TYPE
	Counter32

tmnxDiamPeerStSiDiamRxReqs		1.3.6.1.4.1.6527.3.1.2.58.1.6.1.10
The value of tmnxDiamPeerStSiDiamRxReqs indicates client initiated roundtrip DIAMETER statistics regarding the number of request messages received from server.
Status: current	Access: read-only
OBJECT-TYPE
	Counter32

tmnxDiamPeerStSiDiamTxResps		1.3.6.1.4.1.6527.3.1.2.58.1.6.1.11
The value of tmnxDiamPeerStSiDiamTxResps indicates client initiated roundtrip DIAMETER statistics regarding the number of response messages sent to server.
Status: current	Access: read-only
OBJECT-TYPE
	Counter32

tmnxDiamPeerStErrHdlDiamTxErrCnt		1.3.6.1.4.1.6527.3.1.2.58.1.6.1.12
The value of this object is always equal to zero.
Status: current	Access: read-only
OBJECT-TYPE
	Counter32

tmnxDiamPeerStErrHdlDiamRxErrCnt		1.3.6.1.4.1.6527.3.1.2.58.1.6.1.13
The value of this object is always equal to zero.
Status: current	Access: read-only
OBJECT-TYPE
	Counter32

tmnxDiamPeerStCcrInitialTx		1.3.6.1.4.1.6527.3.1.2.58.1.6.1.14
The value of tmnxDiamPeerStCcrInitialTx indicates the number of Credit Control Request messages with CC-Request-Type AVP equal to INITIAL_REQUEST that are transmitted to the server.
Status: current	Access: read-only
OBJECT-TYPE
	Counter32

tmnxDiamPeerStCcaInitialRx		1.3.6.1.4.1.6527.3.1.2.58.1.6.1.15
The value of tmnxDiamPeerStCcaInitialRx indicates the number of Credit Control Answer messages in response to the CCR INITIAL_REQUEST that are received from the server.
Status: current	Access: read-only
OBJECT-TYPE
	Counter32

tmnxDiamPeerStCcrUpdateTx		1.3.6.1.4.1.6527.3.1.2.58.1.6.1.16
The value of tmnxDiamPeerStCcrUpdateTx indicates the number of Credit Control Request messages with CC-Request-Type AVP equal to UPDATE_REQUEST that are transmitted to the server.
Status: current	Access: read-only
OBJECT-TYPE
	Counter32

tmnxDiamPeerStCcaUpdateRx		1.3.6.1.4.1.6527.3.1.2.58.1.6.1.17
The value of tmnxDiamPeerStCcaUpdateRx indicates the number of Credit Control Answer messages in response to the CCR UPDATE_REQUEST that are received from the server.
Status: current	Access: read-only
OBJECT-TYPE
	Counter32

tmnxDiamPeerStCcrTerminateTx		1.3.6.1.4.1.6527.3.1.2.58.1.6.1.18
The value of tmnxDiamPeerStCcrTerminateTx indicates the number of Credit Control Request messages with CC-Request-Type AVP equal to TERMINATION_REQUEST that are transmitted to the server.
Status: current	Access: read-only
OBJECT-TYPE
	Counter32

tmnxDiamPeerStCcaTerminateRx		1.3.6.1.4.1.6527.3.1.2.58.1.6.1.19
The value of tmnxDiamPeerStCcaTerminateRx indicates the number of Credit Control Answer messages in response to the CCR TERMINATION_REQUEST that are received from the server.
Status: current	Access: read-only
OBJECT-TYPE
	Counter32

tmnxDiamPeerStCerTx		1.3.6.1.4.1.6527.3.1.2.58.1.6.1.20
The value of tmnxDiamPeerStCerTx indicates the number of Capabilities-Exchange-Request messages that are transmitted to the server.
Status: current	Access: read-only
OBJECT-TYPE
	Counter32

tmnxDiamPeerStCeaRx		1.3.6.1.4.1.6527.3.1.2.58.1.6.1.21
The value of tmnxDiamPeerStCeaRx indicates the number of Capabilities-Exchange-Answer messages that are received from the server.
Status: current	Access: read-only
OBJECT-TYPE
	Counter32

tmnxDiamPeerStWdrTx		1.3.6.1.4.1.6527.3.1.2.58.1.6.1.24
The value of tmnxDiamPeerStWdrTx indicates the number of Device-Watchdog-Request messages that are transmitted to the server.
Status: current	Access: read-only
OBJECT-TYPE
	Counter32

tmnxDiamPeerStWdaRx		1.3.6.1.4.1.6527.3.1.2.58.1.6.1.25
The value of tmnxDiamPeerStWdaRx indicates the number of Device-Watchdog-Answer messages that are received from the server.
Status: current	Access: read-only
OBJECT-TYPE
	Counter32

tmnxDiamPeerStWdrRx		1.3.6.1.4.1.6527.3.1.2.58.1.6.1.26
The value of tmnxDiamPeerStWdrRx indicates the number of Device-Watchdog-Request messages that are received from the server.
Status: current	Access: read-only
OBJECT-TYPE
	Counter32

tmnxDiamPeerStWdaTx		1.3.6.1.4.1.6527.3.1.2.58.1.6.1.27
The value of tmnxDiamPeerStWdaTx indicates the number of Device-Watchdog-Answer messages that are transmitted to the server.
Status: current	Access: read-only
OBJECT-TYPE
	Counter32

tmnxDiamPeerStAsrRx		1.3.6.1.4.1.6527.3.1.2.58.1.6.1.30
The value of tmnxDiamPeerStAsrRx indicates the number of Abort-Session-Request messages that are received from the server.
Status: current	Access: read-only
OBJECT-TYPE
	Counter32

tmnxDiamPeerStAsaTx		1.3.6.1.4.1.6527.3.1.2.58.1.6.1.31
The value of tmnxDiamPeerStAsaTx indicates the number of Abort-Session-Answer messages that are transmitted to the server.
Status: current	Access: read-only
OBJECT-TYPE
	Counter32

tmnxDiamPeerStRarRx		1.3.6.1.4.1.6527.3.1.2.58.1.6.1.34
The value of tmnxDiamPeerStRarRx indicates the number of Re-Auth-Request messages that are received from the server.
Status: current	Access: read-only
OBJECT-TYPE
	Counter32

tmnxDiamPeerStRaaTx		1.3.6.1.4.1.6527.3.1.2.58.1.6.1.35
The value of tmnxDiamPeerStRaaTx indicates the number of Re-Auth-Answer messages that are transmitted to the server.
Status: current	Access: read-only
OBJECT-TYPE
	Counter32

tmnxDiamPeerStDprTx		1.3.6.1.4.1.6527.3.1.2.58.1.6.1.36
The value of tmnxDiamPeerStDprTx indicates the number of Disconnect-Peer-Request messages that are transmitted to the server.
Status: current	Access: read-only
OBJECT-TYPE
	Counter32

tmnxDiamPeerStDpaRx		1.3.6.1.4.1.6527.3.1.2.58.1.6.1.37
The value of tmnxDiamPeerStDpaRx indicates the number of Disconnect-Peer-Answer messages that are received from the server.
Status: current	Access: read-only
OBJECT-TYPE
	Counter32

tmnxDiamPeerStDprRx		1.3.6.1.4.1.6527.3.1.2.58.1.6.1.38
The value of tmnxDiamPeerStDprRx indicates the number of Disconnect-Peer-Request messages that are received from the server.
Status: current	Access: read-only
OBJECT-TYPE
	Counter32

tmnxDiamPeerStDpaTx		1.3.6.1.4.1.6527.3.1.2.58.1.6.1.39
The value of tmnxDiamPeerStDpaTx indicates the number of Disconnect-Peer-Answer messages that are transmitted to the server.
Status: current	Access: read-only
OBJECT-TYPE
	Counter32

tmnxDiamPlcyDccaTableLastChngd		1.3.6.1.4.1.6527.3.1.2.58.2.1
The value of tmnxDiamPlcyDccaTableLastChngd indicates the sysUpTime at the time of the most recent management-initiated change to the tmnxDiameterPlcyDccaTable. DCCA = Diameter Credit Control Application.
Status: current	Access: read-only
OBJECT-TYPE
	TimeStamp

tmnxDiameterPlcyDccaTable		1.3.6.1.4.1.6527.3.1.2.58.2.2
The tmnxDiameterPlcyDccaTable has an entry for each DIAMETER policy configured in the system.
Status: current	Access: not-accessible
OBJECT-TYPE
	SEQUENCE OF
		TmnxDiameterPlcyDccaEntry

tmnxDiameterPlcyDccaEntry		1.3.6.1.4.1.6527.3.1.2.58.2.2.1
Each row entry represents DCCA parameters defined for this DIAMETER policy. Entries are created and deleted by the system.
Status: current	Access: not-accessible
OBJECT-TYPE
	TmnxDiameterPlcyDccaEntry

tmnxDiamPlcyDccaLastMgmtChange		1.3.6.1.4.1.6527.3.1.2.58.2.2.1.1
The value of tmnxDiamPlcyDccaLastMgmtChange indicates the sysUpTime at the time of the most recent management-initiated change to this table row.
Status: current	Access: read-only
OBJECT-TYPE
	TimeStamp

tmnxDiamPlcyDccaFailover		1.3.6.1.4.1.6527.3.1.2.58.2.2.1.2
The value of tmnxDiamPlcyDccaFailover specifies whether or not moving the CC message stream to a backup server during an ongoing CC session is supported for this DIAMETER policy.
Status: current	Access: read-create
OBJECT-TYPE
	TruthValue

tmnxDiamPlcyDccaFailureHndlng		1.3.6.1.4.1.6527.3.1.2.58.2.2.1.3
The value of tmnxDiamPlcyDccaFailureHndlng specifies what action to take in case of a DCCA session failure for this DIAMETER policy.
Status: current	Access: read-create
OBJECT-TYPE
	TmnxDiamCcFailureHndlng

tmnxDiamPlcyDccaTxTimer		1.3.6.1.4.1.6527.3.1.2.58.2.2.1.4
The value of tmnxDiamPlcyDccaTxTimer specifies the DCCA Tx Timer (in seconds) for this DIAMETER policy.
Status: current	Access: read-create
OBJECT-TYPE
	Unsigned32	10..1000

tmnxDiamPlcyDccaAvpServCntxtId		1.3.6.1.4.1.6527.3.1.2.58.2.2.1.5
The value of tmnxDiamPlcyDccaAvpServCntxtId specifies the DCCA Service-Context-Id AVP. If set the AVP will be included in CCR (Credit Control Request) messages.
Status: current	Access: read-create
OBJECT-TYPE
	DisplayString	Size(0..32)

tmnxDiamPlcyDccaAvpCldStationId		1.3.6.1.4.1.6527.3.1.2.58.2.2.1.6
The value of tmnxDiamPlcyDccaAvpCldStationId specifies the RADIUS Called-Station-Id AVP. If set, the AVP will be included in CCR (Credit Control Request) messages.
Status: current	Access: read-create
OBJECT-TYPE
	DisplayString	Size(0..64)

tmnxDiamPlcyDccaAvpRadiusUsrNme		1.3.6.1.4.1.6527.3.1.2.58.2.2.1.7
The value of tmnxDiamPlcyDccaAvpRadiusUsrNme specifies whether or not the DIAMETER User-Name AVP will be included in CCR(Credit Control Request) messages.
Status: current	Access: read-create
OBJECT-TYPE
	TruthValue

tmnxDiamPlcyDccaAvpSubIdOrg		1.3.6.1.4.1.6527.3.1.2.58.2.2.1.8
The value of tmnxDiamPlcyDccaAvpSubIdOrg specifies the origin of the information to send in the Subscription-Id-Data AVP.
Status: current	Access: read-create
OBJECT-TYPE
	TmnxDiamPlcyDccaAvpOriginType

tmnxDiamPlcyDccaAvpSubIdType		1.3.6.1.4.1.6527.3.1.2.58.2.2.1.9
The value of tmnxDiamPlcyDccaAvpSubIdType specifies the type of the identifier stored in the Subscription-Id-Data AVP.
Status: current	Access: read-create
OBJECT-TYPE
	INTEGER	endUserE164(0), endUserImsi(1), endUserPrivate(4)

tmnxDiamPlcyDccaAvpNasP		1.3.6.1.4.1.6527.3.1.2.58.2.2.1.10
The value of tmnxDiamPlcyDccaAvpNasP specifies if the NAS-Port-Id AVP will be included in applicable DIAMETER messages.
Status: current	Access: read-create
OBJECT-TYPE
	TruthValue

tmnxDiamPlcyDccaAvpNasPPfixType		1.3.6.1.4.1.6527.3.1.2.58.2.2.1.11
The value of tmnxDiamPlcyDccaAvpNasPPfixType specifies what type of prefix will be added to the NAS-Port AVP if included in DIAMETER messages.
Status: current	Access: read-create
OBJECT-TYPE
	TmnxSubNasPortPrefixType

tmnxDiamPlcyDccaAvpNasPPfixStr		1.3.6.1.4.1.6527.3.1.2.58.2.2.1.12
The value of tmnxDiamPlcyDccaAvpNasPPfixStr specifies the user configurable string to be added as prefix to the NAS-Port AVP if included in DIAMETER messages. This field is only applicable if tmnxDiamPlcyDccaAvpNasPPfixType is set to 'userString'.
Status: current	Access: read-create
OBJECT-TYPE
	DisplayString	Size(0..8)

tmnxDiamPlcyDccaAvpNasPSfixType		1.3.6.1.4.1.6527.3.1.2.58.2.2.1.13
The value of tmnxDiamPlcyDccaAvpNasPSfixType specifies what type of suffix will be added to the NAS-Port attribute NAS-Port AVP if included in DIAMETER messages.
Status: current	Access: read-create
OBJECT-TYPE
	TmnxSubNasPortSuffixType

tmnxDiamPlcyDccaAvpNasPType		1.3.6.1.4.1.6527.3.1.2.58.2.2.1.14
The value of tmnxDiamPlcyDccaAvpNasP specifies if the NAS-Port-Type AVP will be included in applicable DIAMETER messages.
Status: current	Access: read-create
OBJECT-TYPE
	TruthValue

tmnxDiamPlcyDccaAvpImsiOrg		1.3.6.1.4.1.6527.3.1.2.58.2.2.1.15
The value of tmnxDiamPlcyDccaAvpImsiOrg specifies the origin of the information to send in the International Mobile Subscriber Identity (IMSI) AVP.
Status: current	Access: read-create
OBJECT-TYPE
	TmnxDiamPlcyDccaAvpOriginType

tmnxDiamPlcyDccaApplicationType		1.3.6.1.4.1.6527.3.1.2.58.2.2.1.50
The value of tmnxDiamPlcyDccaApplicationType specifies the application type associated with this policy. It defines the set of supported values for the Auth-Application-Id AVP. tmnxDiamPlcyDccaApplicationType \| Auth-Application-Id --------------------------------\|------------------------------------- vfDccaV2 \| 4 (standard) gx \| 16777238 (vendor-specific 3GPP)
Status: current	Access: read-create
OBJECT-TYPE
	TmnxDiamDccaApplicationType

tmnxDiamPlcyDccaMaxPendingReq		1.3.6.1.4.1.6527.3.1.2.58.2.2.1.51
The value of tmnxDiamPlcyDccaMaxPendingReq specifies the maximum number of pending requests for this DIAMETER policy. If the maximum number of pending requests has been exceeded, further requests are buffered or dropped.
Status: current	Access: read-create
OBJECT-TYPE
	Unsigned32	10..131072

tmnxDiamPlcyDccaTxRetryLimit		1.3.6.1.4.1.6527.3.1.2.58.2.2.1.52
The value of tmnxDiamPlcyDccaTxRetryLimit specifies the maximum number of retries for a CCR message associated with this DIAMETER policy.
Status: current	Access: read-create
OBJECT-TYPE
	Unsigned32	0..3

tmnxDiamPlcyDccaOutOfCreditRep		1.3.6.1.4.1.6527.3.1.2.58.2.2.1.53
The value of tmnxDiamPlcyDccaOutOfCreditRep specifies the reporting reason in an intermediate interrogation when the final granted units have been consumed and a corresponding out-of-credit-action different from 'disconnect-host' is started.
Status: current	Access: read-create
OBJECT-TYPE
	INTEGER	final(1), quotaExhausted(2)

tmnxDiamAppPlcyName		1.3.6.1.4.1.6527.3.1.2.58.100.1
The value of tmnxDiamAppPlcyName specifies the name of the DIAMETER policy.
Status: current	Access: accessible-for-notify
OBJECT-TYPE
	TNamedItem

tmnxDiamAppPeerName		1.3.6.1.4.1.6527.3.1.2.58.100.2
The value of tmnxDiamAppPeerName specifies the name of the peer within a DIAMETER policy.
Status: current	Access: accessible-for-notify
OBJECT-TYPE
	TNamedItem

tmnxDiamAppTrapDescription		1.3.6.1.4.1.6527.3.1.2.58.100.3
The value of tmnxDiamAppTrapDescription specifies the diameter application provided description of the failure for this trap.
Status: current	Access: accessible-for-notify
OBJECT-TYPE
	TItemDescription

tmnxDiamAppSessionId		1.3.6.1.4.1.6527.3.1.2.58.100.4
The value of tmnxDiamAppSessionId specifies the diameter session id for this trap.
Status: current	Access: accessible-for-notify
OBJECT-TYPE
	DisplayString	Size(1..102)

tmnxDiamAppSubscrId		1.3.6.1.4.1.6527.3.1.2.58.100.5
The value of tmnxDiamAppSubscrId specifies the subscriber identification for this trap.
Status: current	Access: accessible-for-notify
OBJECT-TYPE
	DisplayString	Size(1..32)

tmnxDiamAppSapId		1.3.6.1.4.1.6527.3.1.2.58.100.6
The value of tmnxDiamAppSapId specifies the SAP identification for this trap.
Status: current	Access: accessible-for-notify
OBJECT-TYPE
	DisplayString	Size(1..32)

tmnxDiamAppSLAProfName		1.3.6.1.4.1.6527.3.1.2.58.100.7
The value of tmnxDiamAppSLAProfName specifies the SLA profile name for this trap.
Status: current	Access: accessible-for-notify
OBJECT-TYPE
	TNamedItem

tmnxDiamPolicyPeerStateChange		1.3.6.1.4.1.6527.3.1.3.58.0.1
A tmnxDiamPolicyPeerStateChange notification is generated when the state of a DIAMETER policy peer changes.
Status: current	Access: accessible-for-notify
NOTIFICATION-TYPE

tmnxDiamAppMessageDropped		1.3.6.1.4.1.6527.3.1.3.58.0.2
The tmnxDiamAppMessageDropped notification indicates that the DIAMETER protocol has dropped a message due to some reason.
Status: current	Access: accessible-for-notify
NOTIFICATION-TYPE

tmnxDiamAppSessionFailure		1.3.6.1.4.1.6527.3.1.3.58.0.3
The tmnxDiamAppSessionFailure notification indicates that the DIAMETER protocol has a session failure.
Status: current	Access: accessible-for-notify
NOTIFICATION-TYPE

tmnxDiameterBaseV7v0Group		1.3.6.1.4.1.6527.3.1.1.58.2.1
The group of objects supporting DIAMETER on Alcatel-Lucent SROS series systems 7.0 release.
Status: obsolete	Access: accessible-for-notify
OBJECT-GROUP

tmnxDiameterDccaGroup		1.3.6.1.4.1.6527.3.1.1.58.2.2
The group of objects supporting DIAMETER DCCA on Alcatel-Lucent SROS series systems.
Status: current	Access: accessible-for-notify
OBJECT-GROUP

tmnxDiameterBaseV8v0Group		1.3.6.1.4.1.6527.3.1.1.58.2.3
The group of objects supporting DIAMETER on Alcatel-Lucent SROS series systems 8.0 release.
Status: current	Access: accessible-for-notify
OBJECT-GROUP

tmnxDiameterDccaGxGroup		1.3.6.1.4.1.6527.3.1.1.58.2.6
The group of objects supporting DIAMETER DCCA Gx Interface on Alcatel-Lucent SROS series systems.
Status: current	Access: accessible-for-notify
OBJECT-GROUP

tmnxDiameterDccaV10v0Group		1.3.6.1.4.1.6527.3.1.1.58.2.7
The group of objects supporting DIAMETER vendor type on Alcatel-Lucent SROS series systems.
Status: current	Access: accessible-for-notify
OBJECT-GROUP

tmnxDiameterNotifyV8v0Group		1.3.6.1.4.1.6527.3.1.1.58.2.4
The group of notifications supporting DIAMETER on Alcatel-Lucent SROS series systems 8.0 release.
Status: obsolete	Access: accessible-for-notify
NOTIFICATION-GROUP

tmnxDiameterV8v0NotifyObjsGroup		1.3.6.1.4.1.6527.3.1.1.58.2.5
The group of objects supporting management of DIAMETER notification objects on Alcatel-Lucent SROS series systems 8.0 release.
Status: obsolete	Access: accessible-for-notify
OBJECT-GROUP

tmnxDiameterNotifyV10v0Group		1.3.6.1.4.1.6527.3.1.1.58.2.8
The group of notifications supporting DIAMETER on Alcatel-Lucent SROS series systems 10.0 release.
Status: current	Access: accessible-for-notify
NOTIFICATION-GROUP

tmnxDiameterV10v0NotifyObjsGroup		1.3.6.1.4.1.6527.3.1.1.58.2.9
The group of objects supporting management of DIAMETER notification objects on Alcatel-Lucent SROS series systems 10.0 release.
Status: current	Access: accessible-for-notify
OBJECT-GROUP

tmnxDiameterV8v0MIBCompliance		1.3.6.1.4.1.6527.3.1.1.58.1.1
The compliance statement for TIMETRA-DIAMETER-MIB on Alcatel-Lucent SROS and 7710 series systems release R8.0.
Status: obsolete	Access: accessible-for-notify
MODULE-COMPLIANCE

tmnxDiameterV10v0MIBCompliance		1.3.6.1.4.1.6527.3.1.1.58.1.2
The compliance statement for TIMETRA-DIAMETER-MIB on Alcatel-Lucent SROS and 7710 series systems release R10.0.
Status: current	Access: accessible-for-notify
MODULE-COMPLIANCE