TIC-RMTI4-G9000-G2020-MIB

File: TIC-RMTI4-G9000-G2020-MIB.mib (57098 bytes)

Imported modules

SNMPv2-TC RFC1155-SMI RFC-1212
RFC-1215

Imported symbols

DisplayString TimeStamp TimeInterval
TestAndIncr AutonomousType enterprises
Integer32 Gauge32 OBJECT-TYPE
TRAP-TYPE

Defined Types

PositiveInteger  
INTEGER 0..2147483647    

NonNegativeInteger  
INTEGER 0..2147483647    

UpsAlarmEntry  
SEQUENCE    
  upsAlarmId PositiveInteger
  upsAlarmDescr AutonomousType
  upsAlarmTime TimeStamp

Defined Values

toshiba 1.3.6.1.4.1.186
OBJECT IDENTIFIER    

equ 1.3.6.1.4.1.186.1
OBJECT IDENTIFIER    

equUPS 1.3.6.1.4.1.186.1.19
OBJECT IDENTIFIER    

ticUPS 1.3.6.1.4.1.186.1.19.2
OBJECT IDENTIFIER    

rmti4 1.3.6.1.4.1.186.1.19.2.5
OBJECT IDENTIFIER    

upsG9000-G2020 1.3.6.1.4.1.186.1.19.2.5.1
OBJECT IDENTIFIER    

upsIdent 1.3.6.1.4.1.186.1.19.2.5.1.1
OBJECT IDENTIFIER    

upsInput 1.3.6.1.4.1.186.1.19.2.5.1.2
OBJECT IDENTIFIER    

upsOutput 1.3.6.1.4.1.186.1.19.2.5.1.3
OBJECT IDENTIFIER    

upsBypass 1.3.6.1.4.1.186.1.19.2.5.1.4
OBJECT IDENTIFIER    

upsBattery 1.3.6.1.4.1.186.1.19.2.5.1.5
OBJECT IDENTIFIER    

upsAlarm 1.3.6.1.4.1.186.1.19.2.5.1.6
OBJECT IDENTIFIER    

upsConfig 1.3.6.1.4.1.186.1.19.2.5.1.7
OBJECT IDENTIFIER    

upsTime 1.3.6.1.4.1.186.1.19.2.5.1.8
OBJECT IDENTIFIER    

upsTrap 1.3.6.1.4.1.186.1.19.2.5.1.9
OBJECT IDENTIFIER    

upsIdentManufacturer 1.3.6.1.4.1.186.1.19.2.5.1.1.1
The name of the UPS manufacturer.
Status: mandatory Access: read-only
OBJECT-TYPE    
  DisplayString Size(0..31)  

upsIdentTypeform 1.3.6.1.4.1.186.1.19.2.5.1.1.2
The UPS Model designation.
Status: mandatory Access: read-only
OBJECT-TYPE    
  DisplayString Size(0..127)  

upsIdentUPSFirmwareVersion 1.3.6.1.4.1.186.1.19.2.5.1.1.3
The UPS firmware version.
Status: mandatory Access: read-only
OBJECT-TYPE    
  DisplayString Size(0..63)  

upsIdentSysName 1.3.6.1.4.1.186.1.19.2.5.1.1.4
A string identifying the UPS. This object is set by the administrator.
Status: mandatory Access: read-write
OBJECT-TYPE    
  DisplayString Size(0..63)  

upsIdentAttachedDevices 1.3.6.1.4.1.186.1.19.2.5.1.1.5
A string identifying the devices attached to the output(s) of the UPS. This object is set by the administrator.
Status: mandatory Access: read-write
OBJECT-TYPE    
  DisplayString Size(0..63)  

upsInputNumOfPhases 1.3.6.1.4.1.186.1.19.2.5.1.2.1
Number of input lines. This data is used by upsInputNumLines.
Status: mandatory Access: read-only
OBJECT-TYPE    
  NonNegativeInteger  

upsInputLLVoltageAB 1.3.6.1.4.1.186.1.19.2.5.1.2.2
The input line to line voltage for AB in RMS volts.
Status: mandatory Access: read-only
OBJECT-TYPE    
  NonNegativeInteger  

upsInputLLVoltageBC 1.3.6.1.4.1.186.1.19.2.5.1.2.3
The input line to line voltage for BC in RMS volts.
Status: mandatory Access: read-only
OBJECT-TYPE    
  NonNegativeInteger  

upsInputLLVoltageCA 1.3.6.1.4.1.186.1.19.2.5.1.2.4
The input line to line voltage for CA in RMS volts.
Status: mandatory Access: read-only
OBJECT-TYPE    
  NonNegativeInteger  

upsInputLLVoltagePercentAB 1.3.6.1.4.1.186.1.19.2.5.1.2.5
The input line to line voltage percent for AB.
Status: mandatory Access: read-only
OBJECT-TYPE    
  NonNegativeInteger  

upsInputLLVoltagePercentBC 1.3.6.1.4.1.186.1.19.2.5.1.2.6
The input line to line voltage percent for BC.
Status: mandatory Access: read-only
OBJECT-TYPE    
  NonNegativeInteger  

upsInputLLVoltagePercentCA 1.3.6.1.4.1.186.1.19.2.5.1.2.7
The input line to line voltage percent for CA.
Status: mandatory Access: read-only
OBJECT-TYPE    
  NonNegativeInteger  

upsInputCurrentPhaseA 1.3.6.1.4.1.186.1.19.2.5.1.2.8
The input phase current for Phase A.
Status: mandatory Access: read-only
OBJECT-TYPE    
  NonNegativeInteger  

upsInputCurrentPhaseB 1.3.6.1.4.1.186.1.19.2.5.1.2.9
The input phase current unit for Phase B.
Status: mandatory Access: read-only
OBJECT-TYPE    
  NonNegativeInteger  

upsInputCurrentPhaseC 1.3.6.1.4.1.186.1.19.2.5.1.2.10
The input phase current unit for Phase C.
Status: mandatory Access: read-only
OBJECT-TYPE    
  NonNegativeInteger  

upsInputFrequency 1.3.6.1.4.1.186.1.19.2.5.1.2.11
The input frequency unit 0.1 Hertz.
Status: mandatory Access: read-only
OBJECT-TYPE    
  NonNegativeInteger  

upsInputActivePowerA 1.3.6.1.4.1.186.1.19.2.5.1.2.12
The magnitude of the present input true power for phase A.
Status: mandatory Access: read-only
OBJECT-TYPE    
  NonNegativeInteger  

upsInputActivePowerB 1.3.6.1.4.1.186.1.19.2.5.1.2.13
The magnitude of the present input true power for phase B.
Status: mandatory Access: read-only
OBJECT-TYPE    
  NonNegativeInteger  

upsInputActivePowerC 1.3.6.1.4.1.186.1.19.2.5.1.2.14
The magnitude of the present input true power for phase C.
Status: mandatory Access: read-only
OBJECT-TYPE    
  NonNegativeInteger  

upsInputTotalActivePower 1.3.6.1.4.1.186.1.19.2.5.1.2.15
The magnitude of the total input true power.
Status: mandatory Access: read-only
OBJECT-TYPE    
  NonNegativeInteger  

upsInputRatedLLVoltage 1.3.6.1.4.1.186.1.19.2.5.1.2.16
The input line to line rated voltage in RMS volts.
Status: mandatory Access: read-only
OBJECT-TYPE    
  NonNegativeInteger  

upsOutputSource 1.3.6.1.4.1.186.1.19.2.5.1.3.1
The present source of output power. The enumeration none(2) indicates that there is no source of output power (and therefore no output power), for example, the system has opened the output breaker.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER other(1), none(2), normal(3), bypass(4), battery(5)  

upsOutputNumOfPhases 1.3.6.1.4.1.186.1.19.2.5.1.3.2
The number of output lines utilized in this device.
Status: mandatory Access: read-only
OBJECT-TYPE    
  NonNegativeInteger  

upsOutputLLVoltageAB 1.3.6.1.4.1.186.1.19.2.5.1.3.3
The output line to line voltage for AB in RMS volts.
Status: mandatory Access: read-only
OBJECT-TYPE    
  NonNegativeInteger  

upsOutputLLVoltageBC 1.3.6.1.4.1.186.1.19.2.5.1.3.4
The output line to line voltage for BC in RMS volts.
Status: mandatory Access: read-only
OBJECT-TYPE    
  NonNegativeInteger  

upsOutputLLVoltageCA 1.3.6.1.4.1.186.1.19.2.5.1.3.5
The output line to line voltage for CA in RMS volts.
Status: mandatory Access: read-only
OBJECT-TYPE    
  NonNegativeInteger  

upsOutputCurrentPhaseA 1.3.6.1.4.1.186.1.19.2.5.1.3.6
The Output phase current for phase A in amps.
Status: mandatory Access: read-only
OBJECT-TYPE    
  NonNegativeInteger  

upsOutputCurrentPhaseB 1.3.6.1.4.1.186.1.19.2.5.1.3.7
The Output phase current for phase B in amps.
Status: mandatory Access: read-only
OBJECT-TYPE    
  NonNegativeInteger  

upsOutputCurrentPhaseC 1.3.6.1.4.1.186.1.19.2.5.1.3.8
The Output phase current for phase C in amps.
Status: mandatory Access: read-only
OBJECT-TYPE    
  NonNegativeInteger  

upsOutputFrequency 1.3.6.1.4.1.186.1.19.2.5.1.3.9
The Output Frequency for phase A in 1/10 of HZ.
Status: mandatory Access: read-only
OBJECT-TYPE    
  NonNegativeInteger  

upsOutputCurrentPercentA 1.3.6.1.4.1.186.1.19.2.5.1.3.10
The output current for phase A in percent.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER  

upsOutputCurrentPercentB 1.3.6.1.4.1.186.1.19.2.5.1.3.11
The output current for phase B in percent.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER  

upsOutputCurrentPercentC 1.3.6.1.4.1.186.1.19.2.5.1.3.12
The output current for phase C in percent.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER  

upsOutputTotalActivePower 1.3.6.1.4.1.186.1.19.2.5.1.3.13
The output active power.
Status: mandatory Access: read-only
OBJECT-TYPE    
  NonNegativeInteger  

upsOutputTotalActivePowerPercent 1.3.6.1.4.1.186.1.19.2.5.1.3.14
The output active power in percent.
Status: mandatory Access: read-only
OBJECT-TYPE    
  NonNegativeInteger  

upsOutputPowerFactor 1.3.6.1.4.1.186.1.19.2.5.1.3.15
The UPS output power factor.
Status: mandatory Access: read-only
OBJECT-TYPE    
  NonNegativeInteger  

upsOutputRatedActivePower 1.3.6.1.4.1.186.1.19.2.5.1.3.16
The output rated active power for the UPS.
Status: mandatory Access: read-only
OBJECT-TYPE    
  NonNegativeInteger  

upsOutputRatedApparentPower 1.3.6.1.4.1.186.1.19.2.5.1.3.17
The output rated apparent power for the UPS.
Status: mandatory Access: read-only
OBJECT-TYPE    
  NonNegativeInteger  

upsOutputRatedLLVoltage 1.3.6.1.4.1.186.1.19.2.5.1.3.18
The output rated line to line voltage for the UPS.
Status: mandatory Access: read-only
OBJECT-TYPE    
  NonNegativeInteger  

upsBypassNumOfPhases 1.3.6.1.4.1.186.1.19.2.5.1.4.1
The number of bypass lines utilized.
Status: mandatory Access: read-only
OBJECT-TYPE    
  NonNegativeInteger  

upsBypassLLVoltageAB 1.3.6.1.4.1.186.1.19.2.5.1.4.2
The Bypass line to line voltage for AB in RMS volts.
Status: mandatory Access: read-only
OBJECT-TYPE    
  NonNegativeInteger  

upsBypassLLVoltageBC 1.3.6.1.4.1.186.1.19.2.5.1.4.3
The Bypass line to line voltage for BC in RMS volts.
Status: mandatory Access: read-only
OBJECT-TYPE    
  NonNegativeInteger  

upsBypassLLVoltageCA 1.3.6.1.4.1.186.1.19.2.5.1.4.4
The Bypass line to line voltage for CA in RMS volts.
Status: mandatory Access: read-only
OBJECT-TYPE    
  NonNegativeInteger  

upsBypassFrequency 1.3.6.1.4.1.186.1.19.2.5.1.4.5
The Bypass frequency in 0.1 Hertz.
Status: mandatory Access: read-only
OBJECT-TYPE    
  NonNegativeInteger  

upsBatteryStatus 1.3.6.1.4.1.186.1.19.2.5.1.5.1
The indication of the capacity remaining in the UPS system's batteries. A value of batteryNormal indicates that the remaining run time sufficient to handle the load. A value of batteryLow indicates the battery level is low. Continued operation in battery mode will deplate batteries. A value of batteryDepleted indicates that the UPS will be unable to sustain the present load when and if the utility power is lost (including the possibility that the utility power is currently absent and the UPS is unable to sustain the output). A value of batteryDischarging indicates UPS system is in Battery power.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER unknown(1), batteryNormal(2), batteryLow(3), batteryDepleted(4), batteryDischarging(5), batteryFailure(6)  

upsElapsedTimeOnBatteryPower 1.3.6.1.4.1.186.1.19.2.5.1.5.2
If the unit is on battery power, the elapsed time since the UPS on battery power, or the time since the network management subsystem was last restarted, whichever is less. Zero shall be returned if the unit is not on battery power.
Status: mandatory Access: read-only
OBJECT-TYPE    
  NonNegativeInteger  

upsEstimatedBatteryRuntime 1.3.6.1.4.1.186.1.19.2.5.1.5.3
An estimate of the time to battery charge depletion under the present load conditions if the utility power is off and remains off, or if it were to be lost and remain off.
Status: mandatory Access: read-only
OBJECT-TYPE    
  PositiveInteger  

upsBatteryVoltage 1.3.6.1.4.1.186.1.19.2.5.1.5.4
The battery voltage DC.
Status: mandatory Access: read-only
OBJECT-TYPE    
  NonNegativeInteger  

upsBatteryVoltagePercent 1.3.6.1.4.1.186.1.19.2.5.1.5.5
Battery voltage in percent.
Status: mandatory Access: read-only
OBJECT-TYPE    
  NonNegativeInteger  

upsBatteryEstimatedCharge 1.3.6.1.4.1.186.1.19.2.5.1.5.6
An estimate of the charge to battery charge depletion under the present load conditions if the utility power is off and remains off, or if it were to be lost and remain off.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER 0..100  

upsBatteryDischargeCurrent 1.3.6.1.4.1.186.1.19.2.5.1.5.7
The present battery discharge Current in percent.
Status: mandatory Access: read-only
OBJECT-TYPE    
  Integer32  

upsBatteryChargeCurrent 1.3.6.1.4.1.186.1.19.2.5.1.5.8
The present battery charge Current in percent.
Status: mandatory Access: read-only
OBJECT-TYPE    
  Integer32  

upsBatteryModel 1.3.6.1.4.1.186.1.19.2.5.1.5.9
The Battery manufacturer.
Status: mandatory Access: read-write
OBJECT-TYPE    
  DisplayString Size(0..15)  

upsBatteryInSeries 1.3.6.1.4.1.186.1.19.2.5.1.5.10
The Battery rated holding time in minutes.
Status: mandatory Access: read-write
OBJECT-TYPE    
  NonNegativeInteger  

upsBatteryNumStrings 1.3.6.1.4.1.186.1.19.2.5.1.5.11
The Battery rated holding time in minutes.
Status: mandatory Access: read-write
OBJECT-TYPE    
  NonNegativeInteger  

upsBatteryRatedAmpereHour 1.3.6.1.4.1.186.1.19.2.5.1.5.12
The Battery rated holding time in minutes.
Status: mandatory Access: read-write
OBJECT-TYPE    
  NonNegativeInteger  

upsBatteryRatedBackupTime 1.3.6.1.4.1.186.1.19.2.5.1.5.13
The Battery rated holding time in minutes.
Status: mandatory Access: read-write
OBJECT-TYPE    
  DisplayString Size(0..8)  

upsBatteryInstallationDate 1.3.6.1.4.1.186.1.19.2.5.1.5.14
The battery install date.
Status: mandatory Access: read-only
OBJECT-TYPE    
  DisplayString Size(10)  

upsAlarmsPresent 1.3.6.1.4.1.186.1.19.2.5.1.6.1
The present number of active alarm conditions.
Status: mandatory Access: read-only
OBJECT-TYPE    
  Gauge32  

upsAlarmTable 1.3.6.1.4.1.186.1.19.2.5.1.6.2
A list of alarm table entries. The table contains zero, one, or many rows at any moment, depending upon the number of alarm conditions in effect. The table is initially empty at agent startup. The agent creates a row in the table each time a condition is detected and deletes that row when that condition no longer pertains. The agent creates the first row with upsAlarmId equal to 1, and increments the value of upsAlarmId each time a new row is created, wrapping to the first free value greater than or equal to 1 when the maximum value of upsAlarmId would otherwise be exceeded. Consequently, after multiple operations, the table may become sparse, e.g., containing entries for rows 95, 100, 101, and 203 and the entries should not be assumed to be in chronological order because upsAlarmId might have wrapped. Alarms are named by an OBJECT IDENTIFIER, upsAlarmDescr, to allow a single table to reflect well known alarms plus alarms defined by a particular implementation, i.e., as documented in the private enterprise MIB definition for the device. No two rows will have the same value of upsAlarmDescr, since alarms define conditions. In order to meet this requirement, care should be taken in the definition of alarm conditions to insure that a system cannot enter the same condition multiple times simultaneously. The number of rows in the table at any given time is reflected by the value of upsAlarmsPresent.
Status: mandatory Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    UpsAlarmEntry

upsAlarmEntry 1.3.6.1.4.1.186.1.19.2.5.1.6.2.1
An entry containing information applicable to a particular alarm.
Status: mandatory Access: not-accessible
OBJECT-TYPE    
  UpsAlarmEntry  

upsAlarmId 1.3.6.1.4.1.186.1.19.2.5.1.6.2.1.1
A unique identifier for an alarm condition. This value must remain constant.
Status: mandatory Access: not-accessible
OBJECT-TYPE    
  PositiveInteger  

upsAlarmDescr 1.3.6.1.4.1.186.1.19.2.5.1.6.2.1.2
A reference to an alarm description object. The object referenced should not be accessible, but rather be used to provide a unique description of the alarm condition.
Status: mandatory Access: read-only
OBJECT-TYPE    
  AutonomousType  

upsAlarmTime 1.3.6.1.4.1.186.1.19.2.5.1.6.2.1.3
The value of sysUpTime when the alarm condition was detected. If the alarm condition was detected at the time of agent startup and presumably existed before agent startup, the value of upsAlarmTime shall equal 0.
Status: mandatory Access: read-only
OBJECT-TYPE    
  TimeStamp  

upsWellKnownAlarms 1.3.6.1.4.1.186.1.19.2.5.1.6.3
OBJECT IDENTIFIER    

upsAlarmFault 1.3.6.1.4.1.186.1.19.2.5.1.6.3.1
Fault: A UPS fault/Alarm condition exists.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER  

upsAlarmOnBattery 1.3.6.1.4.1.186.1.19.2.5.1.6.3.2
Info: The UPS is on Battery mode; it is supplying output power from its batteries.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER  

upsAlarmBatteryLow 1.3.6.1.4.1.186.1.19.2.5.1.6.3.3
Warning: The battery level is low. It has dropped to less than 90% of its nominal value. Continued operation in Battery Mode will deplete Batteries and result in UPS output shut down. Reduce critical load to increase battery runtime.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER  

upsAlarmBatteryDepleted 1.3.6.1.4.1.186.1.19.2.5.1.6.3.4
Warning: UPS contains depleted batteries, it will be unable to support critical loads. Shut down excess equipment to reduce Load.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER  

upsAlarmBatteryOverheat 1.3.6.1.4.1.186.1.19.2.5.1.6.3.5
Fault: Detection of over temperature at the batteries.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER  

upsAlarmBatteryVoltageAbnormal 1.3.6.1.4.1.186.1.19.2.5.1.6.3.6
Fault: Battery voltage is abnormality.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER  

upsAlarmUPSOverheat 1.3.6.1.4.1.186.1.19.2.5.1.6.3.7
Fault: The UPS is overheating (warning is given when the internal temperature reaches and exceeds 50?C rise @ 40?C ambient). Check to see if the ambient temperature is abnormally high (40?C or more). If so, turn on air conditioning. Also, check ventilation fan at the back of the UPS for operation or obstructions. Otherwise, shut down the UPS and contact your Toshiba authorized service center.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER  

upsAlarmPowerFailure 1.3.6.1.4.1.186.1.19.2.5.1.6.3.8
Info: Power Failure.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER  

upsAlarmUPSOverload 1.3.6.1.4.1.186.1.19.2.5.1.6.3.9
Fault: The UPS is overloaded. UPS will switch to bypass operation or shut down if no action is taken. Shut down excess equipment to reduce Load.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER  

upsAlarmUserDefinedOverloadWarning 1.3.6.1.4.1.186.1.19.2.5.1.6.3.10
Warning: The inverter output load % is greater than the user defined overload set point (default: 110%).
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER  

upsAlarmOnBypass 1.3.6.1.4.1.186.1.19.2.5.1.6.3.11
Warning: The UPS is in Stop (Bypass) mode.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER  

upsAlarmOutputOff 1.3.6.1.4.1.186.1.19.2.5.1.6.3.12
Info: The UPS output is off.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER  

upsAlarmAsyncOperation 1.3.6.1.4.1.186.1.19.2.5.1.6.3.13
Warning: Async Operation
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER  

upsAlarmDCBusOverCurrent 1.3.6.1.4.1.186.1.19.2.5.1.6.3.14
Fault: UPS is reporting a DC bus overcurrent condition. Contact your Toshiba authorized service center for examination of a DCOC fault.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER  

upsAlarmDCBusOverVoltage 1.3.6.1.4.1.186.1.19.2.5.1.6.3.15
Fault: UPS is reporting a DC bus overvoltage condition. Contact your Toshiba authorized service center for examination of a DCOV fault.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER  

upsAlarmDCBusUnderVoltage 1.3.6.1.4.1.186.1.19.2.5.1.6.3.16
Fault: UPS is reporting a DC bus undervoltage condition. Contact your Toshiba authorized service center for examination of a DCUV fault.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER  

upsAlarmDCBusImbalanced 1.3.6.1.4.1.186.1.19.2.5.1.6.3.17
Fault: The DC imbalanced alarm detection.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER  

upsAlarmOutputUnderVoltage 1.3.6.1.4.1.186.1.19.2.5.1.6.3.18
Fault: UPS is reporting an output undervoltage condition. Contact your Toshiba authorized service center for examination of a INVUV fault.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER  

upsAlarmOutputOverVoltage 1.3.6.1.4.1.186.1.19.2.5.1.6.3.19
Fault: UPS is reporting an output overvoltage condition. Contact your Toshiba authorized service center for examination of a INVOV fault.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER  

upsAlarmInverterOverload 1.3.6.1.4.1.186.1.19.2.5.1.6.3.20
Fault: Short time over-current has been detected.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER  

upsAlarmInverterOvercurrent 1.3.6.1.4.1.186.1.19.2.5.1.6.3.21
Fault: Detection of inverter overcurrent.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER  

upsAlarmRemotEyeCommError 1.3.6.1.4.1.186.1.19.2.5.1.6.3.22
Warning: Communication error between the RemotEye 4 and the UPS.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER  

upsConfigModelIDString 1.3.6.1.4.1.186.1.19.2.5.1.7.1
UPS Model ID string. This string contains codes for the UPS series,input voltage, output voltage, output VA, and addition option.
Status: mandatory Access: read-only
OBJECT-TYPE    
  DisplayString Size(0..63)  

upsConfigUPSFirmwareVersion 1.3.6.1.4.1.186.1.19.2.5.1.7.2
The G9000 software version.
Status: mandatory Access: read-only
OBJECT-TYPE    
  DisplayString Size(0..63)  

upsConfigInputNumOfPhases 1.3.6.1.4.1.186.1.19.2.5.1.7.3
Number of input lines. This data is used by upsInputNumLines.
Status: mandatory Access: read-only
OBJECT-TYPE    
  NonNegativeInteger  

upsConfigRatedInputFrequency 1.3.6.1.4.1.186.1.19.2.5.1.7.4
The nominal input frequency. On those systems which support read-write access to this object, if there is an attempt to set this variable to a value that is not supported, the request must be rejected and the agent shall respond with an appropriate error message, i.e., badValue for SNMPv1, or inconsistentValue for SNMPv2.
Status: mandatory Access: read-only
OBJECT-TYPE    
  NonNegativeInteger  

upsConfigRatedInputLLVoltage 1.3.6.1.4.1.186.1.19.2.5.1.7.5
The magnitude of the nominal input voltage. On those systems which support read-write access to this object, if there is an attempt to set this variable to a value that is not supported, the request must be rejected and the agent shall respond with an appropriate error message, i.e., badValue for SNMPv1, or inconsistentValue for SNMPv2.
Status: mandatory Access: read-write
OBJECT-TYPE    
  NonNegativeInteger  

upsConfigRatedInputPowerFactor 1.3.6.1.4.1.186.1.19.2.5.1.7.6
UNITS are in hundredths. For 0.95 = 95.
Status: mandatory Access: read-only
OBJECT-TYPE    
  PositiveInteger  

upsConfigOutputNumOfPhases 1.3.6.1.4.1.186.1.19.2.5.1.7.7
Number of output lines. This data is used by upsOutputNumLines.
Status: mandatory Access: read-only
OBJECT-TYPE    
  NonNegativeInteger  

upsConfigRatedOutputFrequency 1.3.6.1.4.1.186.1.19.2.5.1.7.8
The nominal output frequency. On those systems which support read-write access to this object, if there is an attempt to set this variable to a value that is not supported, the request must be rejected and the agent shall respond with an appropriate error message, i.e., bad Value for SNMPv1, or inconsistent Value for SNMPv2.
Status: mandatory Access: read-only
OBJECT-TYPE    
  NonNegativeInteger  

upsConfigRatedOutputLLVoltage 1.3.6.1.4.1.186.1.19.2.5.1.7.9
The magnitude of the nominal output voltage. On those systems which support read-write access to this object, if there is an attempt to set this variable to a value that is not supported, the request must be rejected and the agent shall respond with an appropriate error message, i.e., bad Value for SNMPv1, or inconsistent Value for SNMPv2.
Status: mandatory Access: read-write
OBJECT-TYPE    
  NonNegativeInteger  

upsConfigRatedOutputApperentPower 1.3.6.1.4.1.186.1.19.2.5.1.7.10
The magnitude of the nominal Volt-Amp rating.
Status: mandatory Access: read-only
OBJECT-TYPE    
  NonNegativeInteger  

upsConfigRatedOutputActivePower 1.3.6.1.4.1.186.1.19.2.5.1.7.11
The magnitude of the nominal true power rating.
Status: mandatory Access: read-only
OBJECT-TYPE    
  NonNegativeInteger  

upsConfigRatedOutputPowerFactor 1.3.6.1.4.1.186.1.19.2.5.1.7.12
UNITS are in hundredths. For 0.70 = 70.
Status: mandatory Access: read-only
OBJECT-TYPE    
  NonNegativeInteger  

upsConfigBypassNumOfPhases 1.3.6.1.4.1.186.1.19.2.5.1.7.13
The number of bypass lines utilized.
Status: mandatory Access: read-only
OBJECT-TYPE    
  NonNegativeInteger  

upsConfigLowVoltageTransferPoint 1.3.6.1.4.1.186.1.19.2.5.1.7.14
The minimum input line voltage allowed before the UPS system transfers to battery backup.
Status: mandatory Access: read-write
OBJECT-TYPE    
  NonNegativeInteger  

upsConfigHighVoltageTransferPoint 1.3.6.1.4.1.186.1.19.2.5.1.7.15
The maximum line voltage allowed before the UPS system transfers to battery backup.
Status: mandatory Access: read-write
OBJECT-TYPE    
  NonNegativeInteger  

upsConfigBatteryInSeries 1.3.6.1.4.1.186.1.19.2.5.1.7.16
The number of batteries in each string connected in series.
Status: mandatory Access: read-write
OBJECT-TYPE    
  NonNegativeInteger  

upsConfigBatteryNumStrings 1.3.6.1.4.1.186.1.19.2.5.1.7.17
The number of parallel battery strings.
Status: mandatory Access: read-write
OBJECT-TYPE    
  NonNegativeInteger  

upsConfigRatedBatteryVoltage 1.3.6.1.4.1.186.1.19.2.5.1.7.18
Rated voltage of a single battery.
Status: mandatory Access: read-write
OBJECT-TYPE    
  NonNegativeInteger  

upsConfigRatedBatteryAmpereHour 1.3.6.1.4.1.186.1.19.2.5.1.7.19
The rated battery in ampere hour.
Status: mandatory Access: read-write
OBJECT-TYPE    
  INTEGER  

upsConfigBatteryModel 1.3.6.1.4.1.186.1.19.2.5.1.7.20
The manufacturer of the battery.
Status: mandatory Access: read-write
OBJECT-TYPE    
  DisplayString Size(0..31)  

upsConfigBatteryRatedBackupTime 1.3.6.1.4.1.186.1.19.2.5.1.7.21
The rated duration batteries can hold when unit is in backup mode with full load.
Status: mandatory Access: read-write
OBJECT-TYPE    
  NonNegativeInteger  

upsConfigUserDefinedOverloadSetPoint 1.3.6.1.4.1.186.1.19.2.5.1.7.22
The maximum output load % defined by the user.
Status: mandatory Access: read-write
OBJECT-TYPE    
  INTEGER  

upsConfigBatteryInstallationDate 1.3.6.1.4.1.186.1.19.2.5.1.7.23
The battery install date.
Status: mandatory Access: read-write
OBJECT-TYPE    
  DisplayString Size(10)  

upsConfigSysName 1.3.6.1.4.1.186.1.19.2.5.1.7.24
A string identifying the UPS. This object is set by the administrator.
Status: mandatory Access: read-write
OBJECT-TYPE    
  DisplayString Size(0..31)  

upsConfigAttachedDevices 1.3.6.1.4.1.186.1.19.2.5.1.7.25
A string identifying the devices attached to the output(s) of the UPS. This object is set by the administrator.
Status: mandatory Access: read-write
OBJECT-TYPE    
  DisplayString Size(0..31)  

upsConfigPassword 1.3.6.1.4.1.186.1.19.2.5.1.7.26
Password.
Status: mandatory Access: read-write
OBJECT-TYPE    
  DisplayString Size(0..31)  

upsTimeRealDate 1.3.6.1.4.1.186.1.19.2.5.1.8.1
Present date: year-month-date-day of the week.
Status: mandatory Access: read-write
OBJECT-TYPE    
  DisplayString Size(0..31)  

upsTimeRealTime 1.3.6.1.4.1.186.1.19.2.5.1.8.2
Present time (military format): hour-minute-second. For example,2:00pm would be 14:00:00.
Status: mandatory Access: read-write
OBJECT-TYPE    
  DisplayString Size(0..31)  

upsTrapFault 1
Alarm: One or more fault/status alarm(s) reported.
TRAP-TYPE    

upsTrapFaultClear 2
Alarm Clear: One or more fault/status reported.
TRAP-TYPE    

upsTrapOnBattery 3
Info: The UPS is on Battery Mode.
TRAP-TYPE    

upsTrapOnBatteryClear 4
Info Clear: The UPS is on Battery Mode.
TRAP-TYPE    

upsTrapBatteryLow 5
Warning: Battery Low Voltage.
TRAP-TYPE    

upsTrapBatteryLowClear 6
Warning Clear: Battery Low Voltage.
TRAP-TYPE    

upsTrapBatteryDepleted 7
Warning: UPS contains depleted batteries, it will be unable to support critical loads. Shutdown excess equipment to reduce load.
TRAP-TYPE    

upsTrapBatteryDepletedClear 8
Warning Clear: UPS contains depleted batteries, it will be unable to support critical loads. Shutdown excess equipment to reduce load..
TRAP-TYPE    

upsTrapBatteryOverheat 9
Fault: Battery Overheat.
TRAP-TYPE    

upsTrapBatteryOverheatClear 10
Fault Clear: Battery Overheat.
TRAP-TYPE    

upsTrapBatteryVoltageAbnormal 11
Fault: Battery Voltage Abnormal. Contact your Toshiba authorized service center for examination.
TRAP-TYPE    

upsTrapBatteryVoltageAbnormalClear 12
Fault Clear: Battery Voltage Abnormal. Contact your Toshiba authorized service center for examination.
TRAP-TYPE    

upsTrapUPSOverheat 13
Fault: UPS Overheat, heatsinks temperature exceeds thermal settings. Contact your Toshiba authorized service center for examination.
TRAP-TYPE    

upsTrapUPSOverheatClear 14
Fault Clear: UPS Overheat, heatsinks temperature exceeds thermal settings. Contact your Toshiba authorized service center for examination.
TRAP-TYPE    

upsTrapPowerFailure 15
Info: Power Failure.
TRAP-TYPE    

upsTrapPowerFailureClear 16
Info Clear: PowerFailure.
TRAP-TYPE    

upsTrapUPSOverload 17
Fault: UPS Overload (OL), the output load exceeds the rated current. Decrease load.
TRAP-TYPE    

upsTrapUPSOverloadClear 18
Fault Clear: UPS Overload (OL), the output load exceeds the rated current. Decrease load.
TRAP-TYPE    

upsTrapUserDefinedOverloadWarning 19
Warning: The inverter output load % is greater than the user defined overload set point (default: 110%).
TRAP-TYPE    

upsTrapUserDefinedOverloadWarningClear 20
Warning Clear: The inverter output load % is greater than the user defined overload set point (default: 110%).
TRAP-TYPE    

upsTrapOnBypass 21
Warning:On Bypass.
TRAP-TYPE    

upsTrapOnBypassClear 22
Warning Clear: On Bypass.
TRAP-TYPE    

upsTrapOutputOff 23
Info: The UPS output is off.
TRAP-TYPE    

upsTrapOutputOffClear 24
Info Clear: The UPS output is off.
TRAP-TYPE    

upsTrapAsyncOperation 25
Warning: Inverter Synchronous.
TRAP-TYPE    

upsTrapAsyncOperationClear 26
Warning Clear: Inverter Synchronous.
TRAP-TYPE    

upsTrapDCBusOverCurrent 27
Fault: DC Overcurrent (DCOC). Contact your Toshiba authorized service center for examination.
TRAP-TYPE    

upsTrapDCBusOverCurrentClear 28
Fault Clear: DC Overcurrent (DCOC). Contact your Toshiba authorized service center for examination.
TRAP-TYPE    

upsTrapDCBusOverVoltage 29
Fault: DC Overvoltage (DCOV). Contact your Toshiba authorized service center for examination.
TRAP-TYPE    

upsTrapDCBusOverVoltageClear 30
Fault Clear: DC Overvoltage (DCOV). Contact your Toshiba authorized service center for examination.
TRAP-TYPE    

upsTrapDCBusUnderVoltage 31
Fault: DC Undervoltage (DCUV). Contact your Toshiba authorized service center for examination.
TRAP-TYPE    

upsTrapDCBusUnderVoltageClear 32
Fault Clear: DC Undervoltage (DCUV). Contact your Toshiba authorized service center for examination.
TRAP-TYPE    

upsTrapDCBusImbalance 33
Fault: DC Unbalance. Contact your Toshiba authorized service center for examination.
TRAP-TYPE    

upsTrapDCBusImbalanceClear 34
Fault Clear: DC Unbalance. Contact your Toshiba authorized service center for examination.
TRAP-TYPE    

upsTrapOutputUnderVoltage 35
Fault: Output Undervoltage. Contact your Toshiba authorized service center for examination.
TRAP-TYPE    

upsTrapOutputUnderVoltageClear 36
Fault Clear: Output Undervoltage. Contact your Toshiba authorized service center for examination.
TRAP-TYPE    

upsTrapOutputOverVoltage 37
Fault: Output Overvoltage (VLOV). Contact your Toshiba authorized service center for examination.
TRAP-TYPE    

upsTrapOutputOverVoltageClear 38
Fault Clear: Output Overvoltage (VLOV). Contact your Toshiba authorized service center for examination.
TRAP-TYPE    

upsTrapInverterOverload 39
Fault: UPS Overload, short time over-current has been detected during On-Line operation. Decrease Load.
TRAP-TYPE    

upsTrapInverterOverloadClear 40
Fault Clear: UPS Overload, short time over-current has been detected during On-Line operation. Decrease Load.
TRAP-TYPE    

upsTrapInverterOvercurrent 41
Fault: Inverter Overcurrent. Contact your Toshiba authorized service center for examination.
TRAP-TYPE    

upsTrapInverterOvercurrentClear 42
Fault Clear: Inverter Overcurrent. Contact your Toshiba authorized service center for examination.
TRAP-TYPE    

upsTrapRemotEyeCommError 43
Warning: RemotEye UPS communication error.
TRAP-TYPE    

upsTrapRemotEyeCommErrorClear 44
Warning Clear:RemotEye UPS communication error.
TRAP-TYPE