SYNOPTICS-ETHERNET-MIB

File: SYNOPTICS-ETHERNET-MIB.mib (161158 bytes)

Imported modules

RFC1155-SMI RFC1213-MIB RFC-1212
SYNOPTICS-ROOT-MIB SYNOPTICS-COMMON-MIB

Imported symbols

Counter TimeTicks Gauge
IpAddress DisplayString PhysAddress
OBJECT-TYPE SnpxChassisType SnpxBackplaneType
s3000Ethernet S3ModuleType

Defined Types

S3EnetBoardEntry  
SEQUENCE    
  s3EnetBoardIndex INTEGER
  s3EnetBoardType INTEGER
  s3EnetBoardHwVer INTEGER
  s3EnetBoardStatus INTEGER
  s3EnetBoardReset INTEGER
  s3EnetBoardPartStatus INTEGER
  s3EnetBoardNmCntlStatus INTEGER
  s3EnetBoardPsStatus INTEGER
  s3EnetBoardFrmsRxOk Counter
  s3EnetBoardOctetsRxOk Counter
  s3EnetBoardMcastFrmsRxOk Counter
  s3EnetBoardBcastFrmsRxOk Counter
  s3EnetBoardColls Counter
  s3EnetBoardTooLongErrors Counter
  s3EnetBoardRuntErrors Counter
  s3EnetBoardAlignErrors Counter
  s3EnetBoardFcsErrors Counter
  s3EnetBoardLateCollErrors Counter
  s3EnetBoardAuthStatus INTEGER
  s3EnetBoardAuthAction INTEGER
  s3EnetBoardUpStamp TimeTicks

S3EnetLocBridgeEntry  
SEQUENCE    
  s3EnetLocBridgeIndex INTEGER
  s3EnetLocBridgeDescr DisplayString
  s3EnetLocBridgePortCount INTEGER
  s3EnetLocBridgeDiagSts OCTET STRING
  s3EnetLocBridgeBootSts INTEGER
  s3EnetLocBridgeStandbySts INTEGER

S3EnetLocBridgePortEntry  
SEQUENCE    
  s3EnetLocBridgePortSlotIndex INTEGER
  s3EnetLocBridgePortIndex INTEGER
  s3EnetLocBridgePortMdaId INTEGER
  s3EnetLocBridgePortIf INTEGER
  s3EnetLocBridgePortDescr DisplayString
  s3EnetLocBridgePortOpSts INTEGER

S3EnetRemBridgeEntry  
SEQUENCE    
  s3EnetRemBridgeIndex INTEGER
  s3EnetRemBridgeDescr DisplayString
  s3EnetRemBridgePortCount INTEGER
  s3EnetRemBridgeDiagSts OCTET STRING
  s3EnetRemBridgeBootSts INTEGER
  s3EnetRemBridgeStandbySts INTEGER

S3EnetRemBridgePortEntry  
SEQUENCE    
  s3EnetRemBridgePortSlotIndex INTEGER
  s3EnetRemBridgePortIndex INTEGER
  s3EnetRemBridgePortMdaId INTEGER
  s3EnetRemBridgePortDescr DisplayString
  s3EnetRemBridgePortOpSts INTEGER
  s3EnetRemBridgePortRdySnd INTEGER
  s3EnetRemBridgePortClrSnd INTEGER
  s3EnetRemBridgePortCarDt INTEGER

S3EnetRouterEntry  
SEQUENCE    
  s3EnetRouterIndex INTEGER
  s3EnetRouterDescr DisplayString
  s3EnetRouterDiagSts OCTET STRING
  s3EnetRouterStandbySts INTEGER

S3EnetCommonBoardEntry  
SEQUENCE    
  s3EnetCommonBoardIndex INTEGER
  s3EnetCommonBoardEnetAB INTEGER
  s3EnetCommonBoardChanSwitch INTEGER
  s3EnetCommonBoardRedund INTEGER

S3EnetPortEntry  
SEQUENCE    
  s3EnetPortBoardIndex INTEGER
  s3EnetPortIndex INTEGER
  s3EnetPortLinkStatus INTEGER
  s3EnetPortPartStatus INTEGER
  s3EnetPortJabberStatus INTEGER
  s3EnetPortFrmsRxOk Counter
  s3EnetPortOctetsRxOk Counter
  s3EnetPortMcastFrmsRxOk Counter
  s3EnetPortBcastFrmsRxOk Counter
  s3EnetPortColls Counter
  s3EnetPortTooLongErrors Counter
  s3EnetPortRuntErrors Counter
  s3EnetPortAlignErrors Counter
  s3EnetPortFcsErrors Counter
  s3EnetPortLateCollErrors Counter
  s3EnetPortAuthStatus INTEGER
  s3EnetPortAuthAction INTEGER
  s3EnetPortPartTime TimeTicks
  s3EnetPortType INTEGER
  s3EnetPortInterconStatus INTEGER
  s3EnetPortAddrCollect INTEGER
  s3EnetPortAddrLearnMode INTEGER
  s3EnetPortTxSecurity INTEGER

S3EnetCommonPortEntry  
SEQUENCE    
  s3EnetCommonPortBoardIndex INTEGER
  s3EnetCommonPortIndex INTEGER
  s3EnetCommonPortLinkStatus INTEGER
  s3EnetCommonPortPartStatus INTEGER
  s3EnetCommonPortType INTEGER
  s3EnetCommonPortPartTime TimeTicks

S3EnetRedPortEntry  
SEQUENCE    
  s3EnetRedPortBoardIndex INTEGER
  s3EnetRedPortIndex INTEGER
  s3EnetRedPortRedundMode INTEGER
  s3EnetRedPortOperStatus INTEGER
  s3EnetRedPortRemoteOperStatus INTEGER
  s3EnetRedPortCompanionSlotNo INTEGER
  s3EnetRedPortCompanionPortNo INTEGER
  s3EnetRedPortSwitchoverStatus INTEGER
  s3EnetRedPortSwitchoverTime TimeTicks
  s3EnetRedPortCapability INTEGER

S3EnetNmmTrapServerEntry  
SEQUENCE    
  s3EnetNmmTrapType INTEGER
  s3EnetNmmTrapServerAddress IpAddress
  s3EnetNmmTrapServerComm OCTET STRING

S3EnetShowNodesEntry  
SEQUENCE    
  s3EnetShowNodesSlotIndex INTEGER
  s3EnetShowNodesPortIndex INTEGER
  s3EnetShowNodesMacAddress PhysAddress
  s3EnetShowNodesStatus INTEGER
  s3EnetShowNodesVendorType INTEGER
  s3EnetShowNodesAuthStatus INTEGER

S3EnetFindNodesEntry  
SEQUENCE    
  s3EnetFindNodesMacAddress PhysAddress
  s3EnetFindNodesSlotIndex INTEGER
  s3EnetFindNodesPortIndex INTEGER

S3EnetAuthNodesEntry  
SEQUENCE    
  s3EnetAuthNodesMacAddr PhysAddress
  s3EnetAuthNodesSlotIndex INTEGER
  s3EnetAuthNodesPortIndex INTEGER
  s3EnetAuthNodesStatus INTEGER

S3EnetTopNmmEntry  
SEQUENCE    
  s3EnetTopNmmSlot INTEGER
  s3EnetTopNmmPort INTEGER
  s3EnetTopNmmIpAddr IpAddress
  s3EnetTopNmmMacAddr PhysAddress
  s3EnetTopNmmChassisType SnpxChassisType
  s3EnetTopNmmBkplType SnpxBackplaneType
  s3EnetTopNmmLocalSeg INTEGER
  s3EnetTopNmmNumSeen INTEGER
  s3EnetTopNmmModuleType S3ModuleType
  s3EnetTopNmmNumLinks INTEGER
  s3EnetTopNmmChgStatus INTEGER

S3EnetTopNmmSubsetEntry  
SEQUENCE    
  s3EnetTopNmmSubset OCTET STRING

S3EnetTopBridgeEntry  
SEQUENCE    
  s3EnetTopBridgeIpAddr IpAddress
  s3EnetTopBridgeNumber INTEGER
  s3EnetTopBridgeMacAddr PhysAddress
  s3EnetTopBridgeType INTEGER
  s3EnetTopBridgeStatus INTEGER
  s3EnetTopBridgeSlotNum INTEGER
  s3EnetTopBridgePortNum INTEGER
  s3EnetTopBridgeModuleType S3ModuleType
  s3EnetTopBridgeHelloPortNum INTEGER
  s3EnetTopBridgeHelloPortType INTEGER
  s3EnetTopBridgeHelloPortStatus INTEGER
  s3EnetTopBridgeCompBridgeMac1 PhysAddress
  s3EnetTopBridgeCompBridgeMac2 PhysAddress

S3EnetTopBdgSubsetEntry  
SEQUENCE    
  s3EnetTopBdgSubset OCTET STRING

S3EnetThreshEntry  
SEQUENCE    
  s3EnetThreshIndex INTEGER
  s3EnetThreshStatus INTEGER
  s3EnetThreshObject INTEGER
  s3EnetThreshSlot INTEGER
  s3EnetThreshPort INTEGER
  s3EnetThreshType INTEGER
  s3EnetThreshCondition INTEGER
  s3EnetThreshSetValue INTEGER
  s3EnetThreshActualValue INTEGER
  s3EnetThreshAction INTEGER
  s3EnetThreshExceedCount Counter
  s3EnetThreshDuration TimeTicks

S3EnetSdTrafEntry  
SEQUENCE    
  s3EnetSdTrafMacSA PhysAddress
  s3EnetSdTrafMacDA PhysAddress
  s3EnetSdTrafFrames Counter
  s3EnetSdTrafBytes Counter

S3EnetDsTrafEntry  
SEQUENCE    
  s3EnetDsTrafMacDA PhysAddress
  s3EnetDsTrafMacSA PhysAddress
  s3EnetDsTrafFrames Counter
  s3EnetDsTrafBytes Counter

S3EnetPagedTrafEntry  
SEQUENCE    
  s3EnetTrafPageNo INTEGER
  s3EnetTrafPageEntries OCTET STRING

S3EnetPlusPortEntry  
SEQUENCE    
  s3EnetPlusPortBoardIndex INTEGER
  s3EnetPlusPortIndex INTEGER
  s3EnetPortFragments Counter
  s3EnetPortShortEvents Counter
  s3EnetPortAutoPartitions Counter
  s3EnetPortRateMismatches Counter
  s3EnetPortJabbers Counter
  s3EnetPortLastSrcAddr PhysAddress
  s3EnetPortSrcAddrChanges Counter

S3EnetPlusBoardEntry  
SEQUENCE    
  s3EnetPlusBoardIndex INTEGER
  s3EnetBoardFragments Counter
  s3EnetBoardShortEvents Counter
  s3EnetBoardAutoPartitions Counter
  s3EnetBoardRateMismatches Counter
  s3EnetBoardJabbers Counter

S3EnetFrSizePortEntry  
SEQUENCE    
  s3EnetFrSizePortBoardIndex INTEGER
  s3EnetFrSizePortIndex INTEGER
  s3EnetFrSizePort64to127 Counter
  s3EnetFrSizePort128to255 Counter
  s3EnetFrSizePort256to511 Counter
  s3EnetFrSizePort512to1023 Counter
  s3EnetFrSizePort1024to1518 Counter

S3EnetFrSizeBoardEntry  
SEQUENCE    
  s3EnetFrSizeBoardIndex INTEGER
  s3EnetFrSizeBoard64to127 Counter
  s3EnetFrSizeBoard128to255 Counter
  s3EnetFrSizeBoard256to511 Counter
  s3EnetFrSizeBoard512to1023 Counter
  s3EnetFrSizeBoard1024to1518 Counter

S3EnetProtoPortEntry  
SEQUENCE    
  s3EnetProtoPortBoardIndex INTEGER
  s3EnetProtoPortIndex INTEGER
  s3EnetProtoPort8023Frames Counter
  s3EnetProtoPortEthernetFrames Counter
  s3EnetProtoPortOtherFrames Counter
  s3EnetProtoPortSnaFrames Counter
  s3EnetProtoPortIpFrames Counter
  s3EnetProtoPortIsoFrames Counter
  s3EnetProtoPortArpFrames Counter
  s3EnetProtoPortDecIVFrames Counter
  s3EnetProtoPortDecLatFrames Counter
  s3EnetProtoPortEthTalkFrames Counter
  s3EnetProtoPortXnsFrames Counter
  s3EnetProtoPortIpxFrames Counter
  s3EnetProtoPortDecLavcFrames Counter
  s3EnetProtoPortNetBiosFrames Counter
  s3EnetProtoPortBrdgSpanTreeFrames Counter

S3EnetProtoBoardEntry  
SEQUENCE    
  s3EnetProtoBoardIndex INTEGER
  s3EnetProtoBoard8023Frames Counter
  s3EnetProtoBoardEthernetFrames Counter
  s3EnetProtoBoardOtherFrames Counter
  s3EnetProtoBoardSnaFrames Counter
  s3EnetProtoBoardIpFrames Counter
  s3EnetProtoBoardIsoFrames Counter
  s3EnetProtoBoardArpFrames Counter
  s3EnetProtoBoardDecIVFrames Counter
  s3EnetProtoBoardDecLatFrames Counter
  s3EnetProtoBoardEthTalkFrames Counter
  s3EnetProtoBoardXnsFrames Counter
  s3EnetProtoBoardIpxFrames Counter
  s3EnetProtoBoardDecLavcFrames Counter
  s3EnetProtoBoardNetBiosFrames Counter
  s3EnetProtoBoardBrdgSpanTreeFrames Counter

S3EnetHostEntry  
SEQUENCE    
  s3EnetHostIndex INTEGER
  s3EnetHostObserveOrder INTEGER
  s3EnetHostNetAddr OCTET STRING
  s3EnetHostAddrType INTEGER
  s3EnetHostMacAddress PhysAddress
  s3EnetHostSlotIndex INTEGER
  s3EnetHostPortIndex INTEGER
  s3EnetHostLearnMethod INTEGER
  s3EnetHostTimeStamp TimeTicks

Defined Values

s3000EnetConcentrator 1.3.6.1.4.1.45.1.3.2.1
OBJECT IDENTIFIER    

s3000EnetBoard 1.3.6.1.4.1.45.1.3.2.2
OBJECT IDENTIFIER    

s3000EnetLocBridge 1.3.6.1.4.1.45.1.3.2.2.2
OBJECT IDENTIFIER    

s3000EnetRemBridge 1.3.6.1.4.1.45.1.3.2.2.3
OBJECT IDENTIFIER    

s3000EnetRouter 1.3.6.1.4.1.45.1.3.2.2.4
OBJECT IDENTIFIER    

s3000EnetPort 1.3.6.1.4.1.45.1.3.2.3
OBJECT IDENTIFIER    

s3000EnetNmm 1.3.6.1.4.1.45.1.3.2.4
OBJECT IDENTIFIER    

s3000EnetNode 1.3.6.1.4.1.45.1.3.2.5
OBJECT IDENTIFIER    

s3000EnetTopology 1.3.6.1.4.1.45.1.3.2.6
OBJECT IDENTIFIER    

s3000EnetNmmTopology 1.3.6.1.4.1.45.1.3.2.6.1
OBJECT IDENTIFIER    

s3000EnetBridTopology 1.3.6.1.4.1.45.1.3.2.6.2
OBJECT IDENTIFIER    

s3000EnetTopInfo 1.3.6.1.4.1.45.1.3.2.6.3
OBJECT IDENTIFIER    

s3000EnetThreshold 1.3.6.1.4.1.45.1.3.2.8
OBJECT IDENTIFIER    

s3000EnetSADATraffic 1.3.6.1.4.1.45.1.3.2.9
OBJECT IDENTIFIER    

s3000EnetPlusStatistics 1.3.6.1.4.1.45.1.3.2.10
OBJECT IDENTIFIER    

s3000EnetPlusConc 1.3.6.1.4.1.45.1.3.2.10.3
OBJECT IDENTIFIER    

s3000EnetFrameSizeDist 1.3.6.1.4.1.45.1.3.2.11
OBJECT IDENTIFIER    

s3000EnetFrameConc 1.3.6.1.4.1.45.1.3.2.11.3
OBJECT IDENTIFIER    

s3000EnetProtoTypeDist 1.3.6.1.4.1.45.1.3.2.12
OBJECT IDENTIFIER    

s3000EnetProtoConc 1.3.6.1.4.1.45.1.3.2.12.3
OBJECT IDENTIFIER    

s3000EnetHosts 1.3.6.1.4.1.45.1.3.2.13
OBJECT IDENTIFIER    

s3EnetConcRetimingStatus 1.3.6.1.4.1.45.1.3.2.1.1
Does this concentrator have retiming turned on. Writing a 1 will turn off retiming and writing a 2 will turn on retiming. This will change the active state of retiming but will change the value in EEPROM only when agentWriteEeprom is set.The factory default of this state is on. Retiming cannot be disabled in the 2810 concentrator. The 2810 agent will implement this object as read-only.
OBJECT-TYPE    
  INTEGER off(1), on(2)  

s3EnetConcFrmsRxOk 1.3.6.1.4.1.45.1.3.2.1.2
This contains a count of frames that are successfully received by the concentrator. This does not include frames received with a frame-too-long, runt, FCS, or alignment errors. This counter includes broadcast and multicast frames that are received.
OBJECT-TYPE    
  Counter  

s3EnetConcOctetsRxOk 1.3.6.1.4.1.45.1.3.2.1.3
Contains a count of data and padding octets in frames that are successfully received by the concentrator. This does not include frames received with a frame-too-long, runt, FCS, or alignment errors. This counter includes octets in broadcast and multicast frames that are received. This counter does not include the octets in the CRC field. The octets in the address and length/type fields are counted.
OBJECT-TYPE    
  Counter  

s3EnetConcMcastFrmsRxOk 1.3.6.1.4.1.45.1.3.2.1.4
This contains a count of frames that are successfully received by the concentrator and are directed to an active non-broadcast group address. This does not include frames received with a frame-too-long, runt, FCS, or alignment errors. Only frames that are for a multicast address that this interface is receiving are counted. Broadcast packets are not included.
OBJECT-TYPE    
  Counter  

s3EnetConcBcastFrmsRxOk 1.3.6.1.4.1.45.1.3.2.1.5
This contains a count of frames that are successfully received by the concentrator and are directed to the broadcast group address. This does not include frames received with a frame-too-long, runt, FCS, or alignment errors. Multicast packets are not included.
OBJECT-TYPE    
  Counter  

s3EnetConcColls 1.3.6.1.4.1.45.1.3.2.1.6
This contains a count of the collisions at the concentrator level. For NMM+ this is a true counter. For other NMMs this is a summation of all the port level collision 'flags' for all ports.
OBJECT-TYPE    
  Counter  

s3EnetConcTooLongErrors 1.3.6.1.4.1.45.1.3.2.1.7
This contains a count of frames that are received by the concentrator and exceed the maximum permitted frame size. This counter is incremented when the frameTooLong error is detected.
OBJECT-TYPE    
  Counter  

s3EnetConcRuntErrors 1.3.6.1.4.1.45.1.3.2.1.8
This contains a count of frames received by the concentrator that are less than the minimum permitted frame size and have a good FCS.
OBJECT-TYPE    
  Counter  

s3EnetConcFragErrors 1.3.6.1.4.1.45.1.3.2.1.9
This contains a count of frames received by the concentrator that are less than the minimum permitted frame size and have a bad FCS or alignment error.
OBJECT-TYPE    
  Counter  

s3EnetConcAlignErrors 1.3.6.1.4.1.45.1.3.2.1.10
This contains a count of frames received by the concentrator that are not an integral number of octets in length and do not pass the FCS check. This counter is incremented when the alignment Error status is detected.
OBJECT-TYPE    
  Counter  

s3EnetConcFcsErrors 1.3.6.1.4.1.45.1.3.2.1.11
This contains a count of frames received by the concentrator that are an integral number of octets in length that do not pass the FCS check. This counter is incremented when the frame Check Error status is detected.
OBJECT-TYPE    
  Counter  

s3EnetConcLateCollErrors 1.3.6.1.4.1.45.1.3.2.1.12
This contains a total concentrator count of the late collisions. For NMM+ this is a true counter. For other NMMs this is a summation of all the port level late collision 'flags' for all ports.
OBJECT-TYPE    
  Counter  

s3EnetConcSecureStatus 1.3.6.1.4.1.45.1.3.2.1.13
This s3EnetConcSecureStatus object indicates whether the security features (both allowed nodes and LattisSecure) for the concentrator are active or inactive. If security is active, this object also indicates whether the allowed nodes feature is controlled at the concentrator, board, or port level. LattisSecure features are always controlled at the port level. (See the Authorized Nodes tables for more information about how the allowed nodes and LattisSecure receive security features are configured.) If this object is set to concSecureOn(2), then the allowed nodes feature is controlled at the concentrator level and activated for every non-LattisSecure Ethernet port in the concentrator. If an authorized node violation occurs on any port, the action specified in s3EnetConcAuthAction is taken. If this object is set to portCheckOn(3), then allowed nodes is controlled at the port level by the s3EnetPortSecureStatus object for that port. The port's s3EnetPortAuthAction determines the action taken when authorized nodes violations occur on that port. If this object is set to slotCheckOn(4), then allowed nodes is controlled at the board level by the s3EnetBoardSecureStatus object for that board. The board's s3EnetBoardAuthAction determines the action taken when authorized nodes violations occur on that board's ports. If this object is set to concentratorOff(5), then all security features, including LattisSecure, are deactivated for the entire concentrator. No matter what the status of this object, the board and port level SecureStatus and AuthAction are not lost even if they are not currently being used. Thus, the user can change a port's status even if this object is slotCheckOn(4). If this object is then changed to portCheckOn(3), then the change will take effect. The agent must support download of this object in the CFG file. In release 4.0, this object was called s3EnetConcAuthStatus.
OBJECT-TYPE    
  INTEGER other(1), concSecureOn(2), portCheckOn(3), slotCheckOn(4), concSecureOff(5)  

s3EnetConcAuthAction 1.3.6.1.4.1.45.1.3.2.1.14
If s3EnetConcSecureStatus is concSecureOn(2) and a violation occurs, then the action specified by this object will take place. On a partition, only the port that the violation occurs on will be partitioned. This object does not apply to LattisSecure ports. The agent must support download of this object in the CFG file.
OBJECT-TYPE    
  INTEGER other(1), noAction(2), sendTrap(3), partition(4), sendTrapPartition(5)  

s3EnetConcSecurityLock 1.3.6.1.4.1.45.1.3.2.1.15
If s3EnetConcSecurityLock is locked(2), the agent will refuse all requests to modify the 'security configuration' (defined below) by returning a BadValue return value. If s3EnetConcSecurityLock is notLocked(3), requests to modify security configuration will be handled in the usual manner. SetRequests for objects not included in the security configuration are not affected by the state of this object. Objects that are part of the security configuration are s3EnetConcAuthStatus, s3EnetConcAuthAction, s3EnetBoardAuthStatus, s3EnetBoardAuthAction, s3EnetPortAuthStatus, s3EnetPortAuthAction, s3EnetPortAddrLearnMode, s3EnetPortTxSecurity, and all of the objects in the s3EnetAuthNodesTable.
OBJECT-TYPE    
  INTEGER other(1), locked(2), notLocked(3)  

s3EnetConcEnetChan 1.3.6.1.4.1.45.1.3.2.1.16
Identifies the channel to which this NMM is currently monitoring.
OBJECT-TYPE    
  INTEGER other(1), enetA(2), enetB(3)  

s3EnetBoardTable 1.3.6.1.4.1.45.1.3.2.2.1
A table of board-related objects. The number of entries is given by the number of Ethernet host module and network management module boards that are contained in same backplane Ethernet segment as the reporting NMM.
OBJECT-TYPE    
  SEQUENCE OF  
    S3EnetBoardEntry

s3EnetBoardEntry 1.3.6.1.4.1.45.1.3.2.2.1.1
A table containing objects about Ethernet boards which are currently plugged into the 3000 chassis.
OBJECT-TYPE    
  S3EnetBoardEntry  

s3EnetBoardIndex 1.3.6.1.4.1.45.1.3.2.2.1.1.1
A unique value for each board. Its value ranges between 1 and 12. The value for each board must remain constant at least from one re-initialization of the entity's network management system to the next re-initialization.
OBJECT-TYPE    
  INTEGER  

s3EnetBoardType 1.3.6.1.4.1.45.1.3.2.2.1.1.2
See s3SlotModuleType
OBJECT-TYPE    
  INTEGER empty(1), other(2), m3302(3), m3304-ST(4), m3305(5), m3308(6), m3313(7), m3313M(8), m3314-ST(9), m3314M-ST(10), m3323(11), m3324-ST(12), m3301(16), m3307(17), m3356(18), m3383(24), m3384(25), m331x(26), m3386(32), m3394(33), m3395(34), m3323S(35), m3324S-ST(36), m3307A(37), m3308A(38)  

s3EnetBoardHwVer 1.3.6.1.4.1.45.1.3.2.2.1.1.3
See s3CommonBoardHwVer
OBJECT-TYPE    
  INTEGER  

s3EnetBoardStatus 1.3.6.1.4.1.45.1.3.2.2.1.1.4
See s3CommonBoardStatus
OBJECT-TYPE    
  INTEGER ok(1), fail(2)  

s3EnetBoardReset 1.3.6.1.4.1.45.1.3.2.2.1.1.5
See s3CommonBoardReset
OBJECT-TYPE    
  INTEGER noReset(1), reset(2)  

s3EnetBoardPartStatus 1.3.6.1.4.1.45.1.3.2.2.1.1.6
See s3CommonBoardPartStatus
OBJECT-TYPE    
  INTEGER enabled(1), partition(2)  

s3EnetBoardNmCntlStatus 1.3.6.1.4.1.45.1.3.2.2.1.1.7
See s3CommonBoardCntlStatus
OBJECT-TYPE    
  INTEGER notNmControl(1), nmControl(2)  

s3EnetBoardPsStatus 1.3.6.1.4.1.45.1.3.2.2.1.1.8
See s3CommonBoardPsStatus
OBJECT-TYPE    
  INTEGER ok(1), fail(2)  

s3EnetBoardFrmsRxOk 1.3.6.1.4.1.45.1.3.2.2.1.1.9
This contains a count of frames that are successfully received by the board. This does not include frames received with a frame-too-long, runt, FCS, or alignment errors. This counter includes broadcast and multicast frames that are received.
OBJECT-TYPE    
  Counter  

s3EnetBoardOctetsRxOk 1.3.6.1.4.1.45.1.3.2.2.1.1.10
Contains a count of data and padding octets in frames that are successfully received by the board. This does not include frames received with a frame-too-long, runt, FCS, or alignment errors. This counter includes octets in broadcast and multicast frames that are received. This counter does not include the octets in the CRC field. The octets in the address and length/type fields are counted.
OBJECT-TYPE    
  Counter  

s3EnetBoardMcastFrmsRxOk 1.3.6.1.4.1.45.1.3.2.2.1.1.11
This contains a count of frames that are successfully received by the board and are directed to an active non-broadcast group address. This does not include frames received with a frame-too-long, runt, FCS, or alignment errors. Only frames that are for a multicast address that this interface is receiving are counted. Broadcast packets are not included.
OBJECT-TYPE    
  Counter  

s3EnetBoardBcastFrmsRxOk 1.3.6.1.4.1.45.1.3.2.2.1.1.12
This contains a count of frames that are successfully received by the board and are directed to the broadcast group address. This does not include frames received with a frame-too-long, runt, FCS, or alignment errors. Multicast packets are not included.
OBJECT-TYPE    
  Counter  

s3EnetBoardColls 1.3.6.1.4.1.45.1.3.2.2.1.1.13
This contains a board level count of collisions. For NMM+ this is a true counter. For other NMMs this is a summation of all the port level collision 'flags' for this board.
OBJECT-TYPE    
  Counter  

s3EnetBoardTooLongErrors 1.3.6.1.4.1.45.1.3.2.2.1.1.14
This contains a count of frames that are received by the board and exceed the maximum permitted frame size. This counter is incremented when the frameTooLong error is detected.
OBJECT-TYPE    
  Counter  

s3EnetBoardRuntErrors 1.3.6.1.4.1.45.1.3.2.2.1.1.15
This contains a count of frames received by the board that are less than the minimum permitted frame size and have a good FCS.
OBJECT-TYPE    
  Counter  

s3EnetBoardAlignErrors 1.3.6.1.4.1.45.1.3.2.2.1.1.16
This contains a count of frames received by the board that are not an integral number of octets in length and do not pass the FCS check. This counter is incremented when the alignmentError status is detected.
OBJECT-TYPE    
  Counter  

s3EnetBoardFcsErrors 1.3.6.1.4.1.45.1.3.2.2.1.1.17
This contains a count of frames received by the board that are an integral number of octets in length that do not pass the FCS check. This counter is incremented when the frameCheckError status is detected.
OBJECT-TYPE    
  Counter  

s3EnetBoardLateCollErrors 1.3.6.1.4.1.45.1.3.2.2.1.1.18
This contains a count of the board level late collisions. For NMM+ this is a true counter. For other NMMs this is a summation of all the port level late collision 'flags' for this board.
OBJECT-TYPE    
  Counter  

s3EnetBoardAuthStatus 1.3.6.1.4.1.45.1.3.2.2.1.1.19
This object is only used if s3EnetConcSecureStatus is set to slotCheckOn(4). In this case, turning this object on(2) means that any node that is heard on this board which is not allowed on this board (i.e., not in AuthNode table with the slotIndex equal to this board or 0 for all boards) will cause the action specified in s3EnetBoardAuthAction to take place. If s3EnetConcSecureStatus is set to slotCheckOn(4) but this object is set to off(3), then the authorized nodes feature for this board is deactivated. If s3EnetConcSecureStatus is not set to slotCheckOn(4), then this object will not be used but will maintain its settings unless explicitly changed. This object does not affect the configuration or functioning of security features on LattisSecure Host Modules.
OBJECT-TYPE    
  INTEGER other(1), on(2), off(3)  

s3EnetBoardAuthAction 1.3.6.1.4.1.45.1.3.2.2.1.1.20
If s3EnetConcSecureStatus is slotCheckOn(4) and s3EnetBoardAuthStatus is on(2) and an authorized nodes violation occurs on the board, then the action specified by this object will take place. On a partition, only the port that the violation occurs on will be partitioned. This object does not apply to LattisSecure ports.
OBJECT-TYPE    
  INTEGER other(1), noAction(2), sendTrap(3), partition(4), sendTrapPartition(5)  

s3EnetBoardUpStamp 1.3.6.1.4.1.45.1.3.2.2.1.1.21
The time ( in hundredths of a second) that the board was first seen as a member of this NMM's segment.
OBJECT-TYPE    
  TimeTicks  

s3EnetLocBridgeSlotTable 1.3.6.1.4.1.45.1.3.2.2.2.1
A table of Local Bridge Board entries. The number of entries is determined by the Concentrator Slot Configuration Table. Only those entries that are Ethernet local bridges will have entries in this list.
OBJECT-TYPE    
  SEQUENCE OF  
    S3EnetLocBridgeEntry

s3EnetLocBridgeEntry 1.3.6.1.4.1.45.1.3.2.2.2.1.1
A table containing objects about Boards which are local bridges that are currently plugged into the 3000 chassis.
OBJECT-TYPE    
  S3EnetLocBridgeEntry  

s3EnetLocBridgeIndex 1.3.6.1.4.1.45.1.3.2.2.2.1.1.1
A unique value for each board. Its value ranges between 1 and 12. The value for each board must remain constant at least from one re-initialization of the entity's network management system to the next re-initialization.
OBJECT-TYPE    
  INTEGER  

s3EnetLocBridgeDescr 1.3.6.1.4.1.45.1.3.2.2.2.1.1.2
Description of the local bridge board.
OBJECT-TYPE    
  DisplayString Size(0..128)  

s3EnetLocBridgePortCount 1.3.6.1.4.1.45.1.3.2.2.2.1.1.3
Number of ports that are on the local bridge board.
OBJECT-TYPE    
  INTEGER  

s3EnetLocBridgeDiagSts 1.3.6.1.4.1.45.1.3.2.2.2.1.1.4
Latest Diagnostic LED Status that has been recorded.
OBJECT-TYPE    
  OCTET STRING Size(4)  

s3EnetLocBridgeBootSts 1.3.6.1.4.1.45.1.3.2.2.2.1.1.5
The current status of the board as it relates to rebooting.
OBJECT-TYPE    
  INTEGER other(1), reqstToBoot(2), notReqstToBoot(3)  

s3EnetLocBridgeStandbySts 1.3.6.1.4.1.45.1.3.2.2.2.1.1.6
This status says whether the local bridge is active or in standby mode.
OBJECT-TYPE    
  INTEGER other(1), standby(2), notStandby(3)  

s3EnetLocBridgePortTable 1.3.6.1.4.1.45.1.3.2.2.2.2
A table of Port entries that are part of a local bridge. The number of entries is determined by knowing the number of local bridge boards that are installed by looking at s3ChassisSlotConfigTable and by knowing how many ports are on a local bridge board by looking at s3EnetLocBridgePortCount.
OBJECT-TYPE    
  SEQUENCE OF  
    S3EnetLocBridgePortEntry

s3EnetLocBridgePortEntry 1.3.6.1.4.1.45.1.3.2.2.2.2.1
A table containing objects about the ports of the local bridges that are currently plugged into the 3000 chassis.
OBJECT-TYPE    
  S3EnetLocBridgePortEntry  

s3EnetLocBridgePortSlotIndex 1.3.6.1.4.1.45.1.3.2.2.2.2.1.1
A unique value for each board. Its value ranges between 1 and 12. The value for each board must remain constant at least from one re-initialization of the entity's network management system to the next re-initialization.
OBJECT-TYPE    
  INTEGER  

s3EnetLocBridgePortIndex 1.3.6.1.4.1.45.1.3.2.2.2.2.1.2
A unique value for each port. Its value ranges between 1 and 12. The value for each port must remain constant at least from one re-initialization of the entity's network management system to the next re-initialization.
OBJECT-TYPE    
  INTEGER  

s3EnetLocBridgePortMdaId 1.3.6.1.4.1.45.1.3.2.2.2.2.1.3
Medium dependent ID for the port. See s3SlotModuleMdaId in the SynOptics Common MIB.
OBJECT-TYPE    
  INTEGER  

s3EnetLocBridgePortIf 1.3.6.1.4.1.45.1.3.2.2.2.2.1.4
Bridge interface types.
OBJECT-TYPE    
  INTEGER other(1), etherEther(2), etherTokenRing(3)  

s3EnetLocBridgePortDescr 1.3.6.1.4.1.45.1.3.2.2.2.2.1.5
A text description of the port.
OBJECT-TYPE    
  DisplayString Size(0..128)  

s3EnetLocBridgePortOpSts 1.3.6.1.4.1.45.1.3.2.2.2.2.1.6
Operating status of the port.
OBJECT-TYPE    
  INTEGER other(1), standby(2), notStandby(3)  

s3EnetRemBridgeSlotTable 1.3.6.1.4.1.45.1.3.2.2.3.1
A table of Remote Bridge Board entries. The number of entries is determined by the Concentrator Slot Configuration Table. Only those entries that are Ethernet remote bridges will have entries in this list.
OBJECT-TYPE    
  SEQUENCE OF  
    S3EnetRemBridgeEntry

s3EnetRemBridgeEntry 1.3.6.1.4.1.45.1.3.2.2.3.1.1
A table containing objects about Boards which are remote bridges that are currently plugged into the 3000 chassis.
OBJECT-TYPE    
  S3EnetRemBridgeEntry  

s3EnetRemBridgeIndex 1.3.6.1.4.1.45.1.3.2.2.3.1.1.1
A unique value for each board. Its value ranges between 1 and 12. The value for each board must remain constant at least from one re-initialization of the entity's network management system to the next re-initialization.
OBJECT-TYPE    
  INTEGER  

s3EnetRemBridgeDescr 1.3.6.1.4.1.45.1.3.2.2.3.1.1.2
Description of the board.
OBJECT-TYPE    
  DisplayString Size(0..128)  

s3EnetRemBridgePortCount 1.3.6.1.4.1.45.1.3.2.2.3.1.1.3
Number of ports that are on the board.
OBJECT-TYPE    
  INTEGER  

s3EnetRemBridgeDiagSts 1.3.6.1.4.1.45.1.3.2.2.3.1.1.4
Latest Diagnostic LED Status that has been recorded.
OBJECT-TYPE    
  OCTET STRING Size(4)  

s3EnetRemBridgeBootSts 1.3.6.1.4.1.45.1.3.2.2.3.1.1.5
The current status of the board as it relates to rebooting.
OBJECT-TYPE    
  INTEGER other(1), reqstToBoot(2), notReqstToBoot(3)  

s3EnetRemBridgeStandbySts 1.3.6.1.4.1.45.1.3.2.2.3.1.1.6
This status says whether the remote bridge is active or in standby mode.
OBJECT-TYPE    
  INTEGER other(1), standby(2), notStandby(3)  

s3EnetRemBridgePortTable 1.3.6.1.4.1.45.1.3.2.2.3.2
A table of Port entries that are part of a remote bridge. The number of entries is determined by knowing the number of remote bridge boards that are installed by looking at s3ChassisSlotConfigTable and by knowing how many ports are on a remote bridge board by looking at s3EnetRemBridgePortCount.
OBJECT-TYPE    
  SEQUENCE OF  
    S3EnetRemBridgePortEntry

s3EnetRemBridgePortEntry 1.3.6.1.4.1.45.1.3.2.2.3.2.1
A table containing objects about the ports of the remote bridges that are currently plugged into the 3000 chassis.
OBJECT-TYPE    
  S3EnetRemBridgePortEntry  

s3EnetRemBridgePortSlotIndex 1.3.6.1.4.1.45.1.3.2.2.3.2.1.1
A unique value for each board. Its value ranges between 1 and 12. The value for each board must remain constant at least from one re-initialization of the entity's network management system to the next re-initialization.
OBJECT-TYPE    
  INTEGER  

s3EnetRemBridgePortIndex 1.3.6.1.4.1.45.1.3.2.2.3.2.1.2
A unique value for each port. Its value ranges between 1 and 12. The value for each port must remain constant at least from one re-initialization of the entity's network management system to the next re-initialization.
OBJECT-TYPE    
  INTEGER  

s3EnetRemBridgePortMdaId 1.3.6.1.4.1.45.1.3.2.2.3.2.1.3
Medium dependent ID for the port.
OBJECT-TYPE    
  INTEGER other(1), ethernet(2), x21Barrier(3), x21Unbarrier(4), rs232(5), rs449(6), v35(7), g703(8), t1(9)  

s3EnetRemBridgePortDescr 1.3.6.1.4.1.45.1.3.2.2.3.2.1.4
A text description of the port.
OBJECT-TYPE    
  DisplayString Size(0..128)  

s3EnetRemBridgePortOpSts 1.3.6.1.4.1.45.1.3.2.2.3.2.1.5
Operating status of the port.
OBJECT-TYPE    
  INTEGER other(1), standby(2), operational(3), noLink(4)  

s3EnetRemBridgePortRdySnd 1.3.6.1.4.1.45.1.3.2.2.3.2.1.6
Ready to send status of the port.
OBJECT-TYPE    
  INTEGER other(1), rdySnd(2), notRdySnd(3)  

s3EnetRemBridgePortClrSnd 1.3.6.1.4.1.45.1.3.2.2.3.2.1.7
Clear to send status of the port.
OBJECT-TYPE    
  INTEGER other(1), clrSnd(2), notClrSnd(3)  

s3EnetRemBridgePortCarDt 1.3.6.1.4.1.45.1.3.2.2.3.2.1.8
Carrier detect status of the port.
OBJECT-TYPE    
  INTEGER other(1), carDt(2), noCarDt(3)  

s3EnetRouterSlotTable 1.3.6.1.4.1.45.1.3.2.2.4.1
A table of Router Board entries. The number of entries is determined by the Concentrator Slot Configuration Table. Only those entries that are Ethernet routers will have entries in this list.
OBJECT-TYPE    
  SEQUENCE OF  
    S3EnetRouterEntry

s3EnetRouterEntry 1.3.6.1.4.1.45.1.3.2.2.4.1.1
A table containing objects about Boards which are routers that are currently plugged into the 3000 chassis.
OBJECT-TYPE    
  S3EnetRouterEntry  

s3EnetRouterIndex 1.3.6.1.4.1.45.1.3.2.2.4.1.1.1
A unique value for each board. Its value ranges between 1 and 12. The value for each board must remain constant at least from one re-initialization of the entity's network management system to the next re-initialization.
OBJECT-TYPE    
  INTEGER  

s3EnetRouterDescr 1.3.6.1.4.1.45.1.3.2.2.4.1.1.2
Description of the router board.
OBJECT-TYPE    
  DisplayString Size(0..128)  

s3EnetRouterDiagSts 1.3.6.1.4.1.45.1.3.2.2.4.1.1.3
Latest Diagnostic LED Status that has been recorded.
OBJECT-TYPE    
  OCTET STRING Size(4)  

s3EnetRouterStandbySts 1.3.6.1.4.1.45.1.3.2.2.4.1.1.4
This status says whether the router is active or in standby mode.
OBJECT-TYPE    
  INTEGER other(1), standby(2), notStandby(3)  

s3EnetCommonBoardTable 1.3.6.1.4.1.45.1.3.2.2.5
Information maintained for each Ethernet board. The information can be retrieved for any Ethernet board, even if the board is not on the same backplane Ethernet segment as this NMM. The instance is the slot number of the concentrator that the board occupies.
OBJECT-TYPE    
  SEQUENCE OF  
    S3EnetCommonBoardEntry

s3EnetCommonBoardEntry 1.3.6.1.4.1.45.1.3.2.2.5.1
There is one entry per Ethernet board in this table.
OBJECT-TYPE    
  S3EnetCommonBoardEntry  

s3EnetCommonBoardIndex 1.3.6.1.4.1.45.1.3.2.2.5.1.1
A unique value for each board. Its value ranges between 1 and 12. The value for each board must remain constant at least from one re-initialization of the entity's network management system to the next re-initialization.
OBJECT-TYPE    
  INTEGER  

s3EnetCommonBoardEnetAB 1.3.6.1.4.1.45.1.3.2.2.5.1.2
The channel to which the board is connected. The primary use of this object is for providing realtime switching of boards between channel A and channel B. It is also returned in the enetChannelChange trap, in which case it indicates a board is switched from one channel to the other. The write capability of this object can only apply to those modules with channel switching function. Any attempt to write this object for a non-switchable board, the agent will return badValue.
OBJECT-TYPE    
  INTEGER other(1), enetA(2), enetB(3), enetAandEnetB(4)  

s3EnetCommonBoardChanSwitch 1.3.6.1.4.1.45.1.3.2.2.5.1.3
The agent will return switchCapable(2) for any Ethernet host board which can be switched between Ethernet channels. The value notSwitchCapable(3) indicates that the Ethernet board can not be switched to another channel.
OBJECT-TYPE    
  INTEGER other(1), switchCapable(2), notSwitchCapable(3)  

s3EnetCommonBoardRedund 1.3.6.1.4.1.45.1.3.2.2.5.1.4
The agent will return redundCapable(2) for any Ethernet host board which can provide hardware and/or software controlled redundancy on the port level. The value notRedundCapable(3) indicates that the Ethernet board can not support port redundancy.
OBJECT-TYPE    
  INTEGER other(1), redundCapable(2), notRedundCapable(3)  

s3EnetPortTable 1.3.6.1.4.1.45.1.3.2.3.1
A list of port entries. The number of entries is given by learning the type of board from the information in the s3ChassisSlotConfigTable.
OBJECT-TYPE    
  SEQUENCE OF  
    S3EnetPortEntry

s3EnetPortEntry 1.3.6.1.4.1.45.1.3.2.3.1.1
A table containing objects about the Ports of each board plugged into the 3000 chassis which are on the same backplane Ethernet segment as the reporting NMM.
OBJECT-TYPE    
  S3EnetPortEntry  

s3EnetPortBoardIndex 1.3.6.1.4.1.45.1.3.2.3.1.1.1
A unique value for each board. Its value ranges between 1 and 12. The value for each board must remain constant at least from one reinitialization of the entity's network management system to the next reinitialization.
OBJECT-TYPE    
  INTEGER  

s3EnetPortIndex 1.3.6.1.4.1.45.1.3.2.3.1.1.2
A unique value for each port. Its value is dependent on the board type. The value for each port must remain constant at least from one re-initialization of the entity's network management system to the next re-initialization.
OBJECT-TYPE    
  INTEGER  

s3EnetPortLinkStatus 1.3.6.1.4.1.45.1.3.2.3.1.1.3
Tells whether the port is receiving link status.
OBJECT-TYPE    
  INTEGER off(1), on(2), other(3)  

s3EnetPortPartStatus 1.3.6.1.4.1.45.1.3.2.3.1.1.4
This indicates the operational status of the Port. Writing a partition(2) will partition the port indefinitely and enabled(1) will enable the port. If a timed partition is desired, then writing timedPartition(4) to this object at the same time that a time value is supplied in s3EnetPortPartTime is required. Timed partitions will not survive across a reset. In this case the port will go to the partition(2) state. The value latSecPartition(5) is returned when the port has been automatically partitioned by the LattisSecure Host Module because of a security violation. The value autoPartition(3) is returned when the port has been automatically partitioned by the repeater using the 802.3 repeater auto-partition function. The agent will not allow this object to be set to autoPartition(3) or latSecPartition(5) using an SNMP request.
OBJECT-TYPE    
  INTEGER enabled(1), partition(2), autoPartition(3), timedPartition(4), latSecPartition(5)  

s3EnetPortJabberStatus 1.3.6.1.4.1.45.1.3.2.3.1.1.5
Tells whether the DTE connected to the Port is jabbering or not.
OBJECT-TYPE    
  INTEGER ok(1), jabbering(2)  

s3EnetPortFrmsRxOk 1.3.6.1.4.1.45.1.3.2.3.1.1.6
This contains a count of frames that are successfully received by the port. This does not include frames received with a frame-too-long, runt, FCS, or alignment errors. This counter includes broadcast and multicast frames that are received.
OBJECT-TYPE    
  Counter  

s3EnetPortOctetsRxOk 1.3.6.1.4.1.45.1.3.2.3.1.1.7
Contains a count of data and padding octets in frames that are successfully received by the port. This does not include frames received with a frame-too-long, runt, FCS, or alignment errors. This counter includes octets in broadcast and multicast frames that are received. This counter does not include the octets in the CRC field. The octets in the address and length/type fields are counted.
OBJECT-TYPE    
  Counter  

s3EnetPortMcastFrmsRxOk 1.3.6.1.4.1.45.1.3.2.3.1.1.8
This contains a count of frames that are successfully received by the port and are directed to an active non-broadcast group address. This does not include frames received with a frame-too-long, runt, FCS, or alignment errors. Only frames that are for a multicast address that this interface is receiving are counted. Broadcast packets are not included.
OBJECT-TYPE    
  Counter  

s3EnetPortBcastFrmsRxOk 1.3.6.1.4.1.45.1.3.2.3.1.1.9
This contains a count of frames that are successfully received by the port and are directed to the broadcast group address. This does not include frames received with a frame-too-long, runt, FCS, or alignment errors. Multicast packets are not included.
OBJECT-TYPE    
  Counter  

s3EnetPortColls 1.3.6.1.4.1.45.1.3.2.3.1.1.10
This contains a count of collisions. For NMM+ this is a true counter. For other NMMs this is a count of the collision flags.
OBJECT-TYPE    
  Counter  

s3EnetPortTooLongErrors 1.3.6.1.4.1.45.1.3.2.3.1.1.11
This contains a count of frames that are received by the port and exceed the maximum permitted frame size. This counter is incremented when the frameTooLong error is detected.
OBJECT-TYPE    
  Counter  

s3EnetPortRuntErrors 1.3.6.1.4.1.45.1.3.2.3.1.1.12
This contains a count of frames received by the port that are less than the minimum permitted frame size and have a good FCS.
OBJECT-TYPE    
  Counter  

s3EnetPortAlignErrors 1.3.6.1.4.1.45.1.3.2.3.1.1.13
This contains a count of frames received by the port that are not an integral number of octets in length and do not pass the FCS check. This counter is incremented when the alignmentError status is detected.
OBJECT-TYPE    
  Counter  

s3EnetPortFcsErrors 1.3.6.1.4.1.45.1.3.2.3.1.1.14
This contains a count of frames received the port that are an integral number of octets in length that do not pass the FCS check. This counter is incremented when the frameCheckError status is detected.
OBJECT-TYPE    
  Counter  

s3EnetPortLateCollErrors 1.3.6.1.4.1.45.1.3.2.3.1.1.15
This contains a count of late collisions. For NMM+ this is a true counter. For other NMMs this is a count of the late collision flags.
OBJECT-TYPE    
  Counter  

s3EnetPortAuthStatus 1.3.6.1.4.1.45.1.3.2.3.1.1.16
This object is only used if s3EnetConcSecureStatus is set to portCheckOn(3) or if the port is on a LattisSecure Host Module. In this case, turning this object on(2) means that any node that heard on this port which is not allowed on this port will cause the action specified in s3EnetPortAuthAction to take place. This object does not affect the LattisSecure transmit security feature for the port. It is incompatible with LattisSecure continuous learning mode. If the value of s3EnetPortAddrLearnMode for a LattisSecure port is continuousLearn(3), turning this object to on(2) for that port will not have any affect. If s3EnetConcSecureStatus is set to portCheckOn(3) but this object is set to off(3), then all authorized nodes or LattisSecure receive security features for this port are deactivated. If s3EnetConcSecureStatus is not set to portCheckOn(3), then this object will not be used for allowed nodes, but will be used for LattisSecure.
OBJECT-TYPE    
  INTEGER other(1), on(2), off(3)  

s3EnetPortAuthAction 1.3.6.1.4.1.45.1.3.2.3.1.1.17
If s3EnetConcSecureStatus is portCheckOn(3) or this port is on a LattisSecure Host Module, and s3EnetPortAuthStatus is on(2) and an authorized nodes violation occurs on this port, then the action specified by this object will take place on this port. If the port is a LattisSecure port, the authorized nodes security will be implemented by the LattisSecure Host Module.
OBJECT-TYPE    
  INTEGER other(1), noAction(2), sendTrap(3), partition(4), sendTrapPartition(5)  

s3EnetPortPartTime 1.3.6.1.4.1.45.1.3.2.3.1.1.18
When partitioning the port for a specified time, s3EnetPortPartStatus must be set with timedpartition(4) and this object must be supplied with the duration value. If a PDU sets s3EnetPortPartStatus and not this object, the port will not be partitioned.
OBJECT-TYPE    
  TimeTicks  

s3EnetPortType 1.3.6.1.4.1.45.1.3.2.3.1.1.19
The media connection type for this port. Note that this object was called s3EnetPortMDIXSwitch in the Ethernet 3.3 and 4.0 MIBs.
OBJECT-TYPE    
  INTEGER other(1), tenBaseT(2), tenBaseTMdi(3), aui(4), bnc(5), foirl(6), tenBaseFL(7), switch(8), switchMdi(9), tenBaseFLRedund(10)  

s3EnetPortInterconStatus 1.3.6.1.4.1.45.1.3.2.3.1.1.20
This object tells whether the port is connected to a host or to an interconnect (defined to be another NMM that is sending hello messages). The NMM agent will assign this object the value other(1) on initialization. If it sees hello messages coming in on the port, it will change the InterconStatus to be interconnect(2).
OBJECT-TYPE    
  INTEGER other(1), interconnect(2)  

s3EnetPortAddrCollect 1.3.6.1.4.1.45.1.3.2.3.1.1.21
This object tells whether the NMM should collect node address information from this port for the Find Nodes, Show Nodes, and Traffic Matrix (NMM+ only) tables. By default, the node addresses are collected only from ports that are not identified as interconnect ports. In addition, allowed nodes checking is done only on ports that are not interconnect ports. This object provides a means of overriding the default for collection and checking of node addresses. Setting this variable to default(1) tells the NMM to collect and check addresses if and only the port has not been identified as an interconnect port. To disable node address collection and checking on a port, set this object to neverCollect(2). To collect and check node addresses for an interconnect port, set this object to alwaysCollect(3). This object and its default setting has no affect on LattisSecure receive or transmit security features. To restore the 'natural' value for the port, set this object to default(1).
OBJECT-TYPE    
  INTEGER default(1), neverCollect(2), alwaysCollect(3)  

s3EnetPortAddrLearnMode 1.3.6.1.4.1.45.1.3.2.3.1.1.22
This object indicates whether the port should automatically learn the port address by reading the source address on the incoming packets. This object applies only to ports on a LattisSecure Host Module. For other ports, the agent returns the value other. A Get will return the current learning mode of the port. Setting to noAutoLearn(2) can be used to turn off continuousLearn (3) or oneShotLearn(4). The value of this object is in effect regardless of the value of s3EnetConcSecureStatus or s3EnetPortAuthStatus. Continuous learning is not compatible with LattisSecure receive security, thus s3EnetPortAddrLearnMode should not be set to continuousLearn(3) when s3EnetPortAuthStatus is on(2). If this combination is set, the receive security will not function. If this object is set to oneShotLearn(4), the agent will store the address (when it is learned) into the allowed nodes tables. This can cause the current address to be written over. Because continuous learning is not compatible with receive security, addresses learned while the port is in continuous learning mode will not be stored in the allowed nodes tables. Attempts to set the value to other(1) on a LattisSecure port will be rejected by the agent. Likewise, attempts to set the value to noAutoLearn(2), continuousLearn(3), or oneShotLearn(4) on a non-LattisSecure port will be rejected.
OBJECT-TYPE    
  INTEGER other(1), noAutoLearn(2), continuousLearn(3), oneShotLearn(4)  

s3EnetPortTxSecurity 1.3.6.1.4.1.45.1.3.2.3.1.1.23
This value of this object is meaningful only when s3EnetConcSecureStatus is not set to concSecureOff(5) (i.e., if security features are activated on the concentrator). This object applies only to ports on LattisSecure Host Modules. For other ports, the agent will return other(1) in response to a get request. The value off(3) indicates that LattisSecure transmit security is disabled on this LattisSecure port. The value on(2) indicates that LattisSecure transmit security is enabled on this LattisSecure port. Attempts to set the value to other(1) on a LattisSecure port will be rejected by the agent. Likewise, attempts to set the value to on(2) or off(3) on a non-LattisSecure port will be rejected.
OBJECT-TYPE    
  INTEGER other(1), on(2), off(3)  

s3EnetCommonPortTable 1.3.6.1.4.1.45.1.3.2.3.2
This table provides a list of port entries. The number of entries is given for any Ethernet board in the concentrator, even if the board is not on the same Ethernet segment as this NMM.
OBJECT-TYPE    
  SEQUENCE OF  
    S3EnetCommonPortEntry

s3EnetCommonPortEntry 1.3.6.1.4.1.45.1.3.2.3.2.1
A table containing objects about the ports of each Ethernet board plugged into the 3000-series chassis.
OBJECT-TYPE    
  S3EnetCommonPortEntry  

s3EnetCommonPortBoardIndex 1.3.6.1.4.1.45.1.3.2.3.2.1.1
A unique value for each board. Its value ranges between 1 and 12. The value for each board must remain constant at least from one re-initialization of the entity's network management system to the next re-initialization.
OBJECT-TYPE    
  INTEGER  

s3EnetCommonPortIndex 1.3.6.1.4.1.45.1.3.2.3.2.1.2
A unique value for each port. Its value is dependent on the board type.
OBJECT-TYPE    
  INTEGER  

s3EnetCommonPortLinkStatus 1.3.6.1.4.1.45.1.3.2.3.2.1.3
Tells whether the port is receiving link status.
OBJECT-TYPE    
  INTEGER off(1), on(2), other(3)  

s3EnetCommonPortPartStatus 1.3.6.1.4.1.45.1.3.2.3.2.1.4
This indicates the operational status of the Port. Writing a partition(2) will partition the port indefinitely and enabled(1) will enable the port. If a timed partition is desired, then writing timedPartition(4) to this object at the same time that a time value is supplied in s3EnetCommonPortPartTime is required. Timed partitions will not survive across a reset. In this case the port will go to the partition(2) state. The value latSecPartition(5) is returned when the port has been automatically partitioned by the LattisSecure Host Module because of a security violation. The value autoPartition(3) is returned when the port has been automatically partitioned by the repeater using the 802.3 repeater auto-partition function. The agent will not allow this object to be set to autoPartition(3) or latSecPartition(5) using an SNMP request. Note that the value timedPartition(4) is returned only when the board is timed partitioned by this NMM.
OBJECT-TYPE    
  INTEGER enabled(1), partition(2), autoPartition(3), timedPartition(4), latSecPartition(5)  

s3EnetCommonPortType 1.3.6.1.4.1.45.1.3.2.3.2.1.5
The media connnection type for this port. Note that this object was called s3EnetPortMDIXSwitch in the Ethernet 3.3 and 4.0 MIBs.
OBJECT-TYPE    
  INTEGER other(1), tenBaseT(2), tenBaseTMdi(3), aui(4), bnc(5), foirl(6), tenBaseFL(7), switch(8), switchMdi(9), tenBaseFLRedund(10)  

s3EnetCommonPortPartTime 1.3.6.1.4.1.45.1.3.2.3.2.1.6
When partitioning the port for a specified time, s3EnetCommonPortPartStatus must be set with timedPartition(4) and this object must be supplied with the duration value. If a PDU sets s3EnetCommonPortPartStatus and not this object, the port will not be partitioned.
OBJECT-TYPE    
  TimeTicks  

s3EnetRedPortTable 1.3.6.1.4.1.45.1.3.2.3.3
A table of ports for each 10BASE-FL board with redundancy capability. The number of boards is determined by checking s3EnetCommonBoardRedund having a value of redundCapable(2) for each board in table s3EnetCommonBoardTable.
OBJECT-TYPE    
  SEQUENCE OF  
    S3EnetRedPortEntry

s3EnetRedPortEntry 1.3.6.1.4.1.45.1.3.2.3.3.1
An entry in the table of ports on boards with redundancy capability. Entries in the table cannot be created or deleted via SNMP. Row modification via SNMP is allowed only for ports that support either hardware or software redundancy, but the amount of modifications between the two varies. Entries for boards that support hardware-redundancy only allow the objects s3EnetRedPortRedundMode, s3EnetRedPortSwitchoverStatus, and s3EnetRedPortSwitchoverTime to be modified. The object s3EnetRedPortRedundMode can only be modified on certain agent versions (see the description of the object for more details). Entries for boards that support software-redundancy allow the objects s3EnetRedPortRedundMode, s3EnetRedPortCompanionSlotNo, s3EnetRedPortCompanionPortNo, s3EnetRedPortSwitchoverStatus, and s3EnetRedPortSwitchoverTime to be modified. Software-redundant pairs are configured by sending the objects s3EnetRedPortRedundMode, s3EnetRedPortCompanionSlotNo, and s3EnetRedPortCompanionPortNo in the same SNMP SET PDU, with the object s3EnetRedPortRedundMode set to the value of swActive(4) or swStandby(5). When changing an existing software-redundant pair, the existing pair must first be broken up by setting the object s3EnetRedPortRedundMode to standalone(1), and then a new pair must be configured as described above.
OBJECT-TYPE    
  S3EnetRedPortEntry  

s3EnetRedPortBoardIndex 1.3.6.1.4.1.45.1.3.2.3.3.1.1
The index of the slot containing the board. The value for each board must remain constant at least from one re-initialization of the entity's network management system to the next re-initialization.
OBJECT-TYPE    
  INTEGER  

s3EnetRedPortIndex 1.3.6.1.4.1.45.1.3.2.3.3.1.2
The index of the port on the module.
OBJECT-TYPE    
  INTEGER  

s3EnetRedPortRedundMode 1.3.6.1.4.1.45.1.3.2.3.3.1.3
The redundancy mode of the port. The possible values read, which report the redundancy mode of the port, are: standalone(1)...the port is not in any redundant pair. hwActive(2).....the port is the active companion in a hardware-redundant pair. hwStandby(3)....the port is the standby companion in a hardware-redundant pair. swActive(4).....the port is the active companion in a software-redundant pair. swStandby(5)....the port is the standby companion in a software-redundant pair. The values that can be written, which change the redundancy mode, are: standalone(1)...causes the software-redundant pair to be broken up. hwActive(2).....if the previous value was hwStandby(3), this value will cause the port to become the active port in the hardware-redundant pair (i.e., a switchover). hwStandby(3)....if the previous value was hwActive(2), this value will cause the port to become the standby port in the hardware-redundant pair (i.e., a switchover). swActive(4).....if the previous value was swStandby(5), this value will cause the port to become the active port in the software-redundant pair (i.e., a switchover). swStandby(5)....if the previous value was swActive(4), this value will cause the port to become the standby port in the software-redundant pair (i.e., a switchover). Notes: 1.) The value standalone(1) cannot be written to effect hardware-redundant pairs.
OBJECT-TYPE    
  INTEGER standAlone(1), hwActive(2), hwStandby(3), swActive(4), swStandby(5)  

s3EnetRedPortOperStatus 1.3.6.1.4.1.45.1.3.2.3.3.1.4
This object indicates port's redundancy status. The values are: other(1).........none of the following ok(2)............no fault localFault(3)....the local port has sensed a fault condition. remoteFault(4)...the remote port has sensed a fault condition and has signaled the local port accordingly. Either a localFault(3) or remoteFault(4) condition should cause a redundant port pair to switchover. Notes: If the redundant link is generating on 10BASE-FL without remote fault capability, the value remoteFault(4) will not be reported.
OBJECT-TYPE    
  INTEGER other(1), ok(2), localFault(3), remoteFault(4)  

s3EnetRedPortRemoteOperStatus 1.3.6.1.4.1.45.1.3.2.3.3.1.5
This object reflects the real time status of the received data from the remote port. A value of snpxFLRemFltCpblPortUp(1) indicates that the remote port is capable of 10BASE-FL signaling, as well as SynOptics proprietary remote fault signaling. A remote fault on such a port is indicated by snpxRemFltCpblPortFault(5). A value of snpxFLFBRemFltCpblPortUp(2) indicates that the remote port is capable of 10BASE-FL, 10BASE-FB and SynOptics proprietary remote fault signaling. A remote fault on such a port is indicated by snpxRemFltCpblPortFault(5). A value of tenBaseFLPortUp(3) indicates that the remote port uses regular idle 10BASE-FL signaling, and is incapable of remote fault signaling. A value of tenBaseFBPortUp(4) indicates that the remote port uses 10BASE-FB synchronous signaling. A remote fault on such a port is indicated by tenBaseFBPortFault(6). A value of unknown(7) indicates that the remote signal received is none of the above.
OBJECT-TYPE    
  INTEGER snpxFLRemFltCpblPortUp(1), snpxFLFBRemFltCpblPortUp(2), tenBaseFLPortUp(3), tenBaseFBPortUp(4), snpxRemFltCpblPortFault(5), tenBaseFBPortFault(6), unknown(7)  

s3EnetRedPortCompanionSlotNo 1.3.6.1.4.1.45.1.3.2.3.3.1.6
The slot number of the other port which is in the redundant pair. In the case of a standalone port, a value of 0 will be returned. Note: This object is only writable for ports that support software-redundancy.
OBJECT-TYPE    
  INTEGER  

s3EnetRedPortCompanionPortNo 1.3.6.1.4.1.45.1.3.2.3.3.1.7
The port number of the other port which is in the redundant pair. In the case of a standalone port, a value of 0 will be returned. Note: This object is only writable for ports that support software-redundancy.
OBJECT-TYPE    
  INTEGER  

s3EnetRedPortSwitchoverStatus 1.3.6.1.4.1.45.1.3.2.3.3.1.8
The switchover status of the redundant port pair. The following values can be written: timedSwitchover(2)...Immediately causes the active port to become the standby port, and the standby port to become the active port. Then once the value of s3EnetRedPortSwitchoverTime has elapsed to zero, the ports revert back to their orignal roles. The following values can be read: other(1).............The port is NOT undergoing a timed switchover. timedSwitchover(2)...The port is undergoing a timed switchover. Notes: 1.) When writing timedSwitchover(2) to this object, the SET request must also specify a value for the object s3EnetRedSwitchoverTime. 2.) Once the timed switchover has taken place, the value of this object reverts from timedSwitchover(2) to other(1).
OBJECT-TYPE    
  INTEGER other(1), timedSwitchover(2)  

s3EnetRedPortSwitchoverTime 1.3.6.1.4.1.45.1.3.2.3.3.1.9
The length of time before the ports making up the redundant port pair revert back to their orignal active or standby roles as defined before the timed switchover was setup. The value of this object is meaningful (i.e., non-zero) only when the redundant port pair is undergoing a timed switchover, which is indicated by the object s3EnetRedPortSwitchoverStatus having the value of timedSwitchover(2). This object may only be written in the same SET request that changes the object s3EnetRedPortSwitchoverStatus to timedSwitchover(2). Afterwards, it indicates the amount of time left before the timed switchover is completed, at which time another switchover occurs and s3EnetRedPortSwitchoverStatus is changed to other(1). This object has the value of zero if the port is not undergoing a timed switchover, or if the amount of time is unavailable.
OBJECT-TYPE    
  TimeTicks  

s3EnetRedPortCapability 1.3.6.1.4.1.45.1.3.2.3.3.1.10
The redundancy capability of the port: hwRedOnly(1).........hardware redundancy only. swRedOnly(2).........software redundacy only. notRedunCapable(3)...port not capable of being configured into a redundant port pair. A value of hwRedOnly(1) or swRedOnly(2) means that the port is capable of being configured into a redundant port pair.
OBJECT-TYPE    
  INTEGER hwRedOnly(1), swRedOnly(2), notRedunCapable(3)  

s3EnetRedPortLastChg 1.3.6.1.4.1.45.1.3.2.3.4
The value of sysUptime when the last change in the redundant ports table was observed by the agent.
OBJECT-TYPE    
  TimeTicks  

s3EnetNmmType 1.3.6.1.4.1.45.1.3.2.4.1
See s3AgentType
OBJECT-TYPE    
  INTEGER other(1), m3313(2), m3313M(3), m3314-ST(4), m3314M-ST(5), m3138(6)  

s3EnetNmmMdaHwVer 1.3.6.1.4.1.45.1.3.2.4.2
See AgentMdaHwVer
OBJECT-TYPE    
  INTEGER  

s3EnetNmmFwVer 1.3.6.1.4.1.45.1.3.2.4.3
See s3AgentFwVer
OBJECT-TYPE    
  INTEGER  

s3EnetNmmSwMajorVer 1.3.6.1.4.1.45.1.3.2.4.4
See s3AgentSwMajor
OBJECT-TYPE    
  INTEGER  

s3EnetNmmSwMinorVer 1.3.6.1.4.1.45.1.3.2.4.5
See s3AgentSwMinor
OBJECT-TYPE    
  INTEGER  

s3EnetNmmStatus 1.3.6.1.4.1.45.1.3.2.4.6
See s3AgentStatus
OBJECT-TYPE    
  INTEGER offline(1), online(2)  

s3EnetNmmMode 1.3.6.1.4.1.45.1.3.2.4.7
See s3AgentMode
OBJECT-TYPE    
  INTEGER primary(1), secondary(2)  

s3EnetNmmReset 1.3.6.1.4.1.45.1.3.2.4.8
See s3AgentReset
OBJECT-TYPE    
  INTEGER notreset(1), reset(2)  

s3EnetNmmRestart 1.3.6.1.4.1.45.1.3.2.4.9
See s3AgentRestart
OBJECT-TYPE    
  INTEGER notrestart(1), restart(2)  

s3EnetNmmIpAddr 1.3.6.1.4.1.45.1.3.2.4.10
See s3AgentIpAddr
OBJECT-TYPE    
  IpAddress  

s3EnetNmmNetMask 1.3.6.1.4.1.45.1.3.2.4.11
See s3AgentNetMask
OBJECT-TYPE    
  IpAddress  

s3EnetNmmDefaultGateway 1.3.6.1.4.1.45.1.3.2.4.12
See s3AgentDefaultGateway
OBJECT-TYPE    
  IpAddress  

s3EnetNmmFileServerAddr 1.3.6.1.4.1.45.1.3.2.4.13
See s3AgentBootServerAddr
OBJECT-TYPE    
  IpAddress  

s3EnetNmmBootFile 1.3.6.1.4.1.45.1.3.2.4.14
See s3AgentBootFile
OBJECT-TYPE    
  OCTET STRING Size(0..64)  

s3EnetNmmBootMode 1.3.6.1.4.1.45.1.3.2.4.15
See s3AgentBootMode
OBJECT-TYPE    
  INTEGER eeprom(1), bootp(2)  

s3EnetNmmWriteEeprom 1.3.6.1.4.1.45.1.3.2.4.16
See s3AgentWriteEeprom
OBJECT-TYPE    
  INTEGER notWriteEeprom(1), writeEeprom(2)  

s3EnetNmmBaudRate 1.3.6.1.4.1.45.1.3.2.4.17
See s3AgentBaudRate
OBJECT-TYPE    
  Gauge  

s3EnetNmmInitString 1.3.6.1.4.1.45.1.3.2.4.18
See s3AgentInitString
OBJECT-TYPE    
  OCTET STRING Size(0..64)  

s3EnetNmmLocation 1.3.6.1.4.1.45.1.3.2.4.19
See s3AgentLocation
OBJECT-TYPE    
  OCTET STRING Size(0..64)  

s3EnetNmmTrapServerTable 1.3.6.1.4.1.45.1.3.2.4.20
See s3AgentTrapReceiverTable
OBJECT-TYPE    
  SEQUENCE OF  
    S3EnetNmmTrapServerEntry

s3EnetNmmTrapServerEntry 1.3.6.1.4.1.45.1.3.2.4.20.1
See s3AgentTrapReceiverEntry
OBJECT-TYPE    
  S3EnetNmmTrapServerEntry  

s3EnetNmmTrapType 1.3.6.1.4.1.45.1.3.2.4.20.1.1
See s3AgentTrapRcvrStatus
OBJECT-TYPE    
  INTEGER other(1), invalid(2)  

s3EnetNmmTrapServerAddress 1.3.6.1.4.1.45.1.3.2.4.20.1.2
See s3AgentTrapRcvrNetAddress
OBJECT-TYPE    
  IpAddress  

s3EnetNmmTrapServerComm 1.3.6.1.4.1.45.1.3.2.4.20.1.3
See s3AgentTrapRcvrComm
OBJECT-TYPE    
  OCTET STRING Size(0..20)  

s3EnetNmmAuthTrap 1.3.6.1.4.1.45.1.3.2.4.21
See s3AgentAuthTrap
OBJECT-TYPE    
  INTEGER disable(1), enable(2)  

s3EnetShowNodesTable 1.3.6.1.4.1.45.1.3.2.5.1
Table containing a list of all of the nodes that have been active during the aging interval that are currently connected to the network through this concentrator. This table is different from the FindNodes table in that this table is indexed using the slot, port, and MAC address attributes associated with the node. This allows a manager to get all nodes based on slot, slot-port, or slot-port-MAC.
OBJECT-TYPE    
  SEQUENCE OF  
    S3EnetShowNodesEntry

s3EnetShowNodesEntry 1.3.6.1.4.1.45.1.3.2.5.1.1
List of nodes active on the concentrator and the slot and port the nodes are on.
OBJECT-TYPE    
  S3EnetShowNodesEntry  

s3EnetShowNodesSlotIndex 1.3.6.1.4.1.45.1.3.2.5.1.1.1
The board number the node is on. Valid entries are 1-12.
OBJECT-TYPE    
  INTEGER  

s3EnetShowNodesPortIndex 1.3.6.1.4.1.45.1.3.2.5.1.1.2
The port number the node is on. Valid entries are 1-12.
OBJECT-TYPE    
  INTEGER  

s3EnetShowNodesMacAddress 1.3.6.1.4.1.45.1.3.2.5.1.1.3
This object contains the MAC address (i.e. the Ethernet address) of the node.
OBJECT-TYPE    
  PhysAddress Size(6)  

s3EnetShowNodesStatus 1.3.6.1.4.1.45.1.3.2.5.1.1.4
The status of the node. Determines whether the node has actively transmitted or not over the last 5 seconds.
OBJECT-TYPE    
  INTEGER active(1), inactive(2)  

s3EnetShowNodesVendorType 1.3.6.1.4.1.45.1.3.2.5.1.1.5
The vendor type of the adapter seen on this port. If the vendor is unknown other(1) should be returned.
OBJECT-TYPE    
  INTEGER other(1), threeCom(2)  

s3EnetShowNodesAuthStatus 1.3.6.1.4.1.45.1.3.2.5.1.1.6
The object is used determine how the node was added to this table. If the node was learned by listening to the network then on reads network(2) should be returned. If the node is another NMM or known concentrator device, then nmm(3) is returned. If the device's MAC address is unknown because of some unknown but legal configuration, then other(1) should be returned and s3EnetShowNodesMacAddress should return all zeros. If the node was entered into the AllowedNode list via management control, and was seen on a port that it was authorized to use, then authorized(4) should be returned.
OBJECT-TYPE    
  INTEGER other(1), network(2), nmm(3), authorized(4)  

s3EnetNodeAgeInterval 1.3.6.1.4.1.45.1.3.2.5.2
The time used for aging of the nodes in tables s3EnetShowNodesTable and s3EnetFindNodesTable. Once a node has completely aged it will be removed from these tables. Note: Agents that implement the s3EnetSdTrafTable and s3EnetDsTrafTable tables and do not implement the the object s3EnetTrafAgeInterval (i.e., agents prior to version 5.3), also use s3EnetNodeAgeInterval to age the nodes in these two tables.
OBJECT-TYPE    
  TimeTicks  

s3EnetFindNodesTable 1.3.6.1.4.1.45.1.3.2.5.3
Table containing a list of all of the nodes that have been active during the aging interval that are currently connected to the network through this concentrator. This table is different than the ShowNodes table in that this table is index using only the MAC address attribute associated with the node. This allows a manager to be able to quickly determine if a node with a particular MAC address is located on this concentrator or not.
OBJECT-TYPE    
  SEQUENCE OF  
    S3EnetFindNodesEntry

s3EnetFindNodesEntry 1.3.6.1.4.1.45.1.3.2.5.3.1
Entry in the table containing the slot, port and MAC address of a node connected to the Ethernet through this concentrator.
OBJECT-TYPE    
  S3EnetFindNodesEntry  

s3EnetFindNodesMacAddress 1.3.6.1.4.1.45.1.3.2.5.3.1.1
MAC address of node that this entry in the table is for.
OBJECT-TYPE    
  PhysAddress Size(6)  

s3EnetFindNodesSlotIndex 1.3.6.1.4.1.45.1.3.2.5.3.1.2
The board that the node is connected through.
OBJECT-TYPE    
  INTEGER  

s3EnetFindNodesPortIndex 1.3.6.1.4.1.45.1.3.2.5.3.1.3
The port that the node is connected through.
OBJECT-TYPE    
  INTEGER  

s3EnetAuthNodesTable 1.3.6.1.4.1.45.1.3.2.5.4
Table containing a list of MAC addresses and the slot and ports that the MAC address is allowed to be heard on, in case the authorized node feature is turned on. If a MAC is allowed on any slot and port then the entry will have the slot=0 and the port=0. If the MAC address is allowed on a particular board then slot=allowed board and port=0. If the MAC is only allowed on one port then the entry will contain a slot value and port value between 1-12. Allowed nodes for LattisSecure ports must be configured for that specific port. The agent will reject an attempt to create a slot-level entry for slot=x, port=0, if the board in slot x is a LattisSecure Host Module. Only a single address may be configured for a LattisSecure port. Adding a second address (with the same LattisSecure slot-port number) to the table will cause the first address to be replaced with the new entry. A MAC address can only appear in the table one time. To determine when a station heard on the network must be verified in this table please read the complete description of the authorized node list feature as described with object S3EnetConcAuthStatus. Entries in this table may be downloaded via the CFG file or can be added via SNMP. All adds via SNMP will be lost when the system is reset.
OBJECT-TYPE    
  SEQUENCE OF  
    S3EnetAuthNodesEntry

s3EnetAuthNodesEntry 1.3.6.1.4.1.45.1.3.2.5.4.1
Entry in the table containing a MAC address of a node that is allowed on the ethernet through this concentrator.
OBJECT-TYPE    
  S3EnetAuthNodesEntry  

s3EnetAuthNodesMacAddr 1.3.6.1.4.1.45.1.3.2.5.4.1.1
MAC address of node that this entry in the table is for.
OBJECT-TYPE    
  PhysAddress Size(6)  

s3EnetAuthNodesSlotIndex 1.3.6.1.4.1.45.1.3.2.5.4.1.2
The board that the node is allowed to be heard through. If this object is 0, then the MAC address is allowed on any board in the concentrator. In this case s3EnetAuthNodesPortIndex should also be 0. Otherwise, this object describes the slot that the MAC address of this entry is allowed to connect to.
OBJECT-TYPE    
  INTEGER  

s3EnetAuthNodesPortIndex 1.3.6.1.4.1.45.1.3.2.5.4.1.3
The port that the node is allowed to be heard through. If this object is 0, then the MAC address of this entry is allowed to connect to any port on the board (if s3EnetAuthNodesSlotIndex is not 0) or if s3EnetAuthNodesSlotIndex is 0, then the MAC address is allowed to be heard from any port on the concentrator. Otherwise, this object specifies which port on the s3EnetAuthNodesSlotIndex this MAC address is allowed to be heard on.
OBJECT-TYPE    
  INTEGER  

s3EnetAuthNodesStatus 1.3.6.1.4.1.45.1.3.2.5.4.1.4
The status of the AuthNodes entry. The primary use of this object is for modifying the AuthNodes table. It is also returned in the enetAuthViolation trap, in which case it indicates whether the violating MAC address was found in the AuthNodes table. Setting this entry to invalid(1) causes the entry to be deleted from the table. Setting a new entry with valid(2) causes the entry to be created in the table. The response to a get request or get-next request will always indicate a status of valid(2), since invalid entries are removed from the table.
OBJECT-TYPE    
  INTEGER invalid(1), valid(2)  

s3EnetMaxNodesPerPort 1.3.6.1.4.1.45.1.3.2.5.5
Maximun number of MAC address remembered by the agent on a per port basis, this number should be smaller than the maximum limit imposed by the agent.
OBJECT-TYPE    
  INTEGER 0..65535  

s3EnetTopNmmTable 1.3.6.1.4.1.45.1.3.2.6.1.1
A table of the NMM's in the flat network.
OBJECT-TYPE    
  SEQUENCE OF  
    S3EnetTopNmmEntry

s3EnetTopNmmEntry 1.3.6.1.4.1.45.1.3.2.6.1.1.1
Table that contains information about NMMs that are in the same flat network as this NMM.
OBJECT-TYPE    
  S3EnetTopNmmEntry  

s3EnetTopNmmSlot 1.3.6.1.4.1.45.1.3.2.6.1.1.1.1
Slot that the NMM this entry is for can be found using the topology protocol. This is the slot from which a topology message was received.
OBJECT-TYPE    
  INTEGER  

s3EnetTopNmmPort 1.3.6.1.4.1.45.1.3.2.6.1.1.1.2
Port that the NMM this entry is for can be found using the topology protocol. This is the port from which a topology message was received.
OBJECT-TYPE    
  INTEGER  

s3EnetTopNmmIpAddr 1.3.6.1.4.1.45.1.3.2.6.1.1.1.3
IpAddress of the NMM this entry is for. This is the IP address of the NMM that sent a topology message.
OBJECT-TYPE    
  IpAddress  

s3EnetTopNmmMacAddr 1.3.6.1.4.1.45.1.3.2.6.1.1.1.4
MAC Address of the NMM this entry is for.
OBJECT-TYPE    
  PhysAddress Size(6)  

s3EnetTopNmmChassisType 1.3.6.1.4.1.45.1.3.2.6.1.1.1.5
Concentrator type of the NMM this entry is for. The enumerated values of this object are the same as defined in the common MIB for object s3ChassisType.
OBJECT-TYPE    
  SnpxChassisType  

s3EnetTopNmmBkplType 1.3.6.1.4.1.45.1.3.2.6.1.1.1.6
Concentrator backplane type of the NMM this entry is for. The enumerated values of this object are the same as defined in the common MIB for object s3ChassisBkplType.
OBJECT-TYPE    
  SnpxBackplaneType  

s3EnetTopNmmLocalSeg 1.3.6.1.4.1.45.1.3.2.6.1.1.1.7
Does this entry NMM exist in the same segment as this (the reporting) NMM.
OBJECT-TYPE    
  INTEGER true(1), false(2)  

s3EnetTopNmmNumSeen 1.3.6.1.4.1.45.1.3.2.6.1.1.1.8
Number of NMMs visible from the slot-port pair that this NMM is seen through.
OBJECT-TYPE    
  INTEGER  

s3EnetTopNmmModuleType 1.3.6.1.4.1.45.1.3.2.6.1.1.1.9
The module type of the NMM that this entry is for. The values of this object are equivalent to those defined in the common MIB for object s3SlotModuleType.
OBJECT-TYPE    
  S3ModuleType  


s3EnetTopNmmChgStatus 1.3.6.1.4.1.45.1.3.2.6.1.1.1.11
If this NMM has detected any change of topology relative to itself it will set this object to change(1), otherwise noChange(2) will be returned.
OBJECT-TYPE    
  INTEGER changed(1), noChange(2)  

s3EnetTopNmmHelloTime 1.3.6.1.4.1.45.1.3.2.6.1.2
Hello Time interval used in the topology update protocol.
OBJECT-TYPE    
  TimeTicks  

s3EnetTopNmmSubsetTable 1.3.6.1.4.1.45.1.3.2.6.1.3
Encoded octet string of the s3EnetTopNmmTable.
OBJECT-TYPE    
  SEQUENCE OF  
    S3EnetTopNmmSubsetEntry

s3EnetTopNmmSubsetEntry 1.3.6.1.4.1.45.1.3.2.6.1.3.1
Encoded octet string of the s3EnetTopNmmTable. Instance returned in Response PDU: On GETs: instance specified is the instance returned. On GET-NEXTs: instance returned is the instance of the last record contained in the octet string.
OBJECT-TYPE    
  S3EnetTopNmmSubsetEntry  

s3EnetTopNmmSubset 1.3.6.1.4.1.45.1.3.2.6.1.3.1.1
Encoded octet string. On reads it contains an integral number of s3EnetTopNmmEntry records. All entries are the same size. Values are specified in SynOptics technical documents.
OBJECT-TYPE    
  OCTET STRING Size(0..1400)  

s3EnetTopBridgeTable 1.3.6.1.4.1.45.1.3.2.6.2.1
A table of Bridges that are in the same segment as this NMM network.
OBJECT-TYPE    
  SEQUENCE OF  
    S3EnetTopBridgeEntry

s3EnetTopBridgeEntry 1.3.6.1.4.1.45.1.3.2.6.2.1.1
Table that contains information about Bridges that are in the same segment as this NMM.
OBJECT-TYPE    
  S3EnetTopBridgeEntry  

s3EnetTopBridgeIpAddr 1.3.6.1.4.1.45.1.3.2.6.2.1.1.1
IP address of the bridge from the Hello PDU.
OBJECT-TYPE    
  IpAddress  

s3EnetTopBridgeNumber 1.3.6.1.4.1.45.1.3.2.6.2.1.1.2
Bridge Number assigned to this bridge.
OBJECT-TYPE    
  INTEGER  

s3EnetTopBridgeMacAddr 1.3.6.1.4.1.45.1.3.2.6.2.1.1.3
MAC Address of this bridge.
OBJECT-TYPE    
  PhysAddress Size(6)  

s3EnetTopBridgeType 1.3.6.1.4.1.45.1.3.2.6.2.1.1.4
Kind of bridge this entry represents.
OBJECT-TYPE    
  INTEGER other(1), localSyn2Port(2), remoteSyn3Port(3), etherSwitch(4)  

s3EnetTopBridgeStatus 1.3.6.1.4.1.45.1.3.2.6.2.1.1.5
Current operational status of this bridge.
OBJECT-TYPE    
  INTEGER other(1), active(2), standby(3)  

s3EnetTopBridgeSlotNum 1.3.6.1.4.1.45.1.3.2.6.2.1.1.6
Slot on the concentrator that the Hello PDU from the bridge was received.
OBJECT-TYPE    
  INTEGER  

s3EnetTopBridgePortNum 1.3.6.1.4.1.45.1.3.2.6.2.1.1.7
Port on concentrator that the Hello PDU from the bridge was received.
OBJECT-TYPE    
  INTEGER  

s3EnetTopBridgeModuleType 1.3.6.1.4.1.45.1.3.2.6.2.1.1.8
Module type of the board that the Hello PDU from the Bridge was received.
OBJECT-TYPE    
  S3ModuleType  

s3EnetTopBridgeHelloPortNum 1.3.6.1.4.1.45.1.3.2.6.2.1.1.9
Port Number on the Bridge from which the Hello PDU was sent.
OBJECT-TYPE    
  INTEGER  

s3EnetTopBridgeHelloPortType 1.3.6.1.4.1.45.1.3.2.6.2.1.1.10
Type of the Port on the Bridge from which the Hello PDU was sent.
OBJECT-TYPE    
  INTEGER other(1), ether(2), tokenRing4(3), tokenRing16(4), fddi(5), t1(6)  

s3EnetTopBridgeHelloPortStatus 1.3.6.1.4.1.45.1.3.2.6.2.1.1.11
Status of the Port on the Bridge from which the Hello PDU was sent.
OBJECT-TYPE    
  INTEGER other(1), active(2), standby(3)  

s3EnetTopBridgeCompBridgeMac1 1.3.6.1.4.1.45.1.3.2.6.2.1.1.12
Contains one of the 2 companion MAC addresses of the remote bridge. If this entry is for a local bridge or is unknown, then this object should contain the MAC address of 0:0:0:0:0:0.
OBJECT-TYPE    
  PhysAddress Size(6)  

s3EnetTopBridgeCompBridgeMac2 1.3.6.1.4.1.45.1.3.2.6.2.1.1.13
Contains one of the 2 companion MAC addresses of the remote bridge. If this entry is for a local bridge or is unknown, then this object should contain the MAC address of 0:0:0:0:0:0.
OBJECT-TYPE    
  PhysAddress Size(6)  

s3EnetTopBdgSubsetTable 1.3.6.1.4.1.45.1.3.2.6.2.2
Encoded octet string of the s3EnetTopBridgeTable.
OBJECT-TYPE    
  SEQUENCE OF  
    S3EnetTopBdgSubsetEntry

s3EnetTopBdgSubsetEntry 1.3.6.1.4.1.45.1.3.2.6.2.2.1
Encoded octet string of the s3EnetTopBridgeTable. Instance returned in Response PDU: On GETs: instance specified is the instance returned. On GET-NEXTs: instance returned is the instance of the last record contained in the octet string.
OBJECT-TYPE    
  S3EnetTopBdgSubsetEntry  

s3EnetTopBdgSubset 1.3.6.1.4.1.45.1.3.2.6.2.2.1.1
Encoded octet string. On reads it contains an integral number of s3EnetTopBridgeEntry records. All entries are the same size. Values are specified in SynOptics technical documents.
OBJECT-TYPE    
  OCTET STRING Size(0..1400)  

s3EnetTopNmmLstChg 1.3.6.1.4.1.45.1.3.2.6.3.1
The value of sysUpTime the last time an entry in the NMM topology table was added, deleted, or modified. If the NMM topology table has not changed since cold/warm start of the agent, then the value is zero.
OBJECT-TYPE    
  TimeTicks  

s3EnetTopBridgeLstChg 1.3.6.1.4.1.45.1.3.2.6.3.2
The value of sysUpTime the last time an entry in the bridge topology table was added, deleted, or modified. If the bridge topology table has not changed since cold/warm start of the agent, then the value is zero.
OBJECT-TYPE    
  TimeTicks  

s3EnetThreshTable 1.3.6.1.4.1.45.1.3.2.8.1
The table of thresholds. There are three kinds of thresholds supported in the threshold table: port thresholds, slot thresholds, and concentrator thresholds. The object s3EnetThreshObject in the threshold table is used to specify the kind of threshold for the table entry. When the value of the object s3EnetThreshObject is port(4), the threshold entry applies to a specific port, which is identified by the value of the objects s3EnetThreshSlot and s3EnetThreshPort. The port must be on the same segment as the NMM in order for the NMM to monitor the threshold. When the value of the object s3EnetThreshObject is slot(3), the threshold entry applies to a specific slot, which is identified by the value of the object s3EnetThreshSlot. The slot must be on the same segment as the NMM in order for the NMM to monitor the threshold. When the value of the object s3EnetThreshObject is concentrator(2), the threshold entry applies to the segment the NMM is connected to within the concentrator.
OBJECT-TYPE    
  SEQUENCE OF  
    S3EnetThreshEntry

s3EnetThreshEntry 1.3.6.1.4.1.45.1.3.2.8.1.1
A row in the Ethernet Threshold Table. The following columns must be specified in a SNMP SET request to create a row in the table for each of the three kinds of thresholds (each name is prefixed by s3EnetThresh): PORT SLOT CONCENTRATOR ========= ========= ============ Status=(1) Status=(1) Status=(1) Object=(4) Object=(3) Object=(2) Slot Slot Port Type Type Type Condition Condition Condition SetValue SetValue SetValue Action Action Action *Duration Duration Duration with the object s3EnetThreshStatus set to the value addActive(1). Notes: 1.) The value of s3EnetThreshObject selects the kind of threshold for the row (i.e., for port thresholds it is set to the value port(4), for slot thresholds it is set to the value slot(3), and for concentrator thresholds it is set to the value concentrator(2)). 2.) The object s3EnetThreshPort is not used for creating slot level thresholds, and is set to 0 by the agent when the row is created. 3.) The objects s3EnetThreshPort and s3EnetThreshSlot are not used for creating concentrator level thresholds, and are both set to 0 by the agent when the row is created. 4.) The value of s3EnetThreshDuration is ignored for port level link status thresholds. To delete a row in the table, the object s3EnetThreshStatus needs to be specified in a SNMP SET request with its value equal to delDead(2).
OBJECT-TYPE    
  S3EnetThreshEntry  

s3EnetThreshIndex 1.3.6.1.4.1.45.1.3.2.8.1.1.1
The index into the threshold table.
OBJECT-TYPE    
  INTEGER  

s3EnetThreshStatus 1.3.6.1.4.1.45.1.3.2.8.1.1.2
The status of the threshold. The possible values for a write are: addActive(1)...If the entry does not exist, the entry is created as long as the other necessary objects are in the SNMP SET request. If the entry does exist and is inactive, it is activated. delDead(2).....Causes the entry to be deleted from the table. It could take 5 seconds after delDead(2) is written to actually delete the entry due to task scheduling. The possible values for a read are: addActive(1)...This threshold entry is active. delDead(2).....This threshold entry is inactive and will be deleted in 5 seconds or less.
OBJECT-TYPE    
  INTEGER addActive(1), delDead(2)  

s3EnetThreshObject 1.3.6.1.4.1.45.1.3.2.8.1.1.3
Specifies the part of the concentrator the threshold applies. The possible values are: other(1)..........Unknown threshold (error) concentrator(2)...The threshold applies to the segment the NMM is connected to within the concentrator slot(3)...........The threshold applies to a specific slot in the concentrator identified by s3EnetThreshSlot port(4)...........The threshold applies to a specific port in the concentrator identified by s3EnetThreshSlot and s3EnetThreshPort All values are read-write with the exception of other(1), which is read-only. See the description of the object s3EnetThreshType for the explanation of which thresholds are applicable to port(4), slot(3), and concentrator(2).
OBJECT-TYPE    
  INTEGER other(1), concentrator(2), slot(3), port(4)  

s3EnetThreshSlot 1.3.6.1.4.1.45.1.3.2.8.1.1.4
If s3EnetThreshObject is slot(3) or port(4), then this contains a valid slot. Otherwise, the contents of this object is meaningless.
OBJECT-TYPE    
  INTEGER  

s3EnetThreshPort 1.3.6.1.4.1.45.1.3.2.8.1.1.5
If s3EnetThreshObject is port(4), then this contains a valid port. Otherwise, the contents of this object is meaningless.
OBJECT-TYPE    
  INTEGER  

s3EnetThreshType 1.3.6.1.4.1.45.1.3.2.8.1.1.6
Determines which type of threshold applies to this entry. The possible values that can be read and written are listed below. Applicable to ALL Thresholds ============================================== goodBytes(2).........Count of good bytes goodPkts(3)..........Count of good packets badPkts(4)...........Count of bad packets crcPkts(5)...........Count of packets with CRC errors misaligned(6)........Count of misaligned packets runtPkts(7)..........Count of runt packets fragPkts(8)..........Count of fragmented packets tooLong(9)...........Count of too long packets collision(10)........Count of collisions lateColls(11)........Count of late collisions multicast(13)........Count of multicast packets broadcast(14)........Count of broadcast packets shortEvents(15)......Count of short events dataRateMismatches(17).... Count of data rate mismatches networkErrors(18)......... Count of short events, late collisions, and data rate mismatches badToGoodPktRatio(19)..... Ratio of bad packets to good packets, where bad packets is the sum of packets with alignment errors, packets with FCS errors, runt packets, and packets that are too long netErrToGoodPktRatio(20)... Ratio of network error packets to good packets, where network error packets is the sum of short event packets, packets with late collisions, and data rate mismatch packets colltoGoodPktRatio(21)..... Ratio of collision packets to good packets Applicable ONLY to Port Thresholds ============================================== linkStatus(12).......Status of the link srcAddrChanges(16)...Count of source address changes Applicable ONLY to Concentrator Thresholds ============================================== collBackOffErr(22)...Count of collision backoff errors Note: 1.) The value other(1) can only be read and it indicates the entry has an invalid or unknown threshold type.
OBJECT-TYPE    
  INTEGER other(1), goodBytes(2), goodPkts(3), badPkts(4), crcPkts(5), misaligned(6), runtPkts(7), fragPkts(8), tooLong(9), collision(10), lateColls(11), linkStatus(12), multicast(13), broadcast(14), shortEvents(15), srcAddrChanges(16), dataRateMismatches(17), networkErrors(18), badToGoodPktRatio(19), netErrToGoodPktRatio(20), colltoGoodPktRatio(21), collBackOffErr(22)  

s3EnetThreshCondition 1.3.6.1.4.1.45.1.3.2.8.1.1.7
Conditions that set off the threshold. The possible values are: other(1)........None of the following crossValue(2)...The value of s3EnetThreshActualValue crosses the value of s3EnetThreshSetValue (i.e., either from lower to higher or from higher to lower) overValue(3)....The value of s3EnetThreshActualValue is greater than s3EnetThreshSetValue overRate(4).....The rate of s3EnetThreshActualValue/sec is greater than s3EnetThreshSetValue/sec linkOn(5).......The link status of the port has changed to ON linkOff(6)......The link status of the port has changed to OFF overRatio(7)....The ratio in s3EnetThreshActualValue is greater than s3EnetThreshSetValue. Both values are in units of 0.01% (i.e., 100 equals 1.0%) The values that the object s3EnetThreshCondition can have is actually dependent on the value of the object s3EnetThreshType. The table below shows the valid combinations between the two objects. If s3EnetThreshType Allowed Values For Is Equal To s3EnetThreshCondition Are =================== ========================= goodBytes(2) 2, 3, 4 goodPkts(3) 2, 3, 4 badPkts(4) 2, 3, 4 crcPkts(5) 2, 3, 4 misaligned(6) 2, 3, 4 runtPkts(7) 2, 3, 4 fragPkts(8) 2, 3, 4 tooLong(9) 2, 3, 4 collision(10) 2, 3, 4 lateColls(11) 2, 3, 4 linkStatus(12) 5, 6 multicast(13) 2, 3, 4 broadcast(14) 2, 3, 4 shortEvents(15) 2, 3, 4 srcAddrChanges(16) 2, 3, 4 dataRateMismatches(17) 2, 3, 4 networkErrors(18) 2, 3, 4 badToGoodPktRatio(19) 7 netErrToGoodPktRatio(20) 7 colltoGoodPktRatio(21) 7 collBackOffErr(22) 2, 3, 4 When the condition specified is crossValue(2) or overValue(3), the value of s3EnetThreshActualValue is accumulated from the beginning of the duration window and is checked every 5 seconds. When the condition specified is overRate(4) or overRatio(5), and the duration is less than or equal to 5 seconds, the value of s3EnetThreshActualValue is based on the data accumulated during the 5 second sampling period. When the condition specified is overRate(4) or overRatio(5), and the duration is greater than 5 seconds, the value of s3EnetThreshActualValue is based on the data accumulated during the entire duration window.
OBJECT-TYPE    
  INTEGER other(1), crossValue(2), overValue(3), overRate(4), linkOn(5), linkOff(6), overRatio(7)  

s3EnetThreshSetValue 1.3.6.1.4.1.45.1.3.2.8.1.1.8
Threshold setting value.
OBJECT-TYPE    
  INTEGER  

s3EnetThreshActualValue 1.3.6.1.4.1.45.1.3.2.8.1.1.9
Current value of the threshold counter. This object is set to zero at the begining of each duration window.
OBJECT-TYPE    
  INTEGER  

s3EnetThreshAction 1.3.6.1.4.1.45.1.3.2.8.1.1.10
Determines what action is to take place if the threshold condition occurs. The possible values that can be read and written are listed below. Applicable to ALL Thresholds ============================================== noAction(2)............Take no action sendTrap(3)............Send a trap Applicable ONLY to Port Thresholds ============================================== partSlot(6)............Partition the slot identified by s3EnetThreshSlot partSlotPort(7)........Partition the port identified by s3EnetThreshSlot and s3EnetThreshPort Applicable ONLY to Slot Thresholds ============================================== trapPartSlot(10).......Send a trap and partition the slot identified by s3EnetThreshSlot trapPartSlotPort(11)...Send a trap and partition the port identified by s3EnetThreshSlot and s3EnetThreshPort Notes: 1.) The value other(1) can only be read and it indicates the entry has an invalid or unknown threshold action. 2.) The values res4(4), res5(5), res8(8), and res9(9) are no longer used and should never be read or written. The timing and frequency of the action taken when the threshold condition is met is dependent upon the type of condition (i.e., s3EnetThreshCondition) and the length of the duration window (i.e., s3EnetThreshDuration). If the threshold condition is crossValue(2), the action will be taken only ONCE during the duration window at the sampling period the condition is first met. If the threshold condition is overValue(3), linkOn(5), or linkOff(6), the action will be taken at each sampling period the condition is met until the end of the duration window. If the threshold condition is overRate(4) or overRatio(5) the action will be taken only ONCE at the end of the duration window if the condition is met.
OBJECT-TYPE    
  INTEGER other(1), noAction(2), sendTrap(3), res4(4), res5(5), partSlot(6), partSlotPort(7), res8(8), res9(9), trapPartSlot(10), trapPartSlotPort(11)  

s3EnetThreshExceedCount 1.3.6.1.4.1.45.1.3.2.8.1.1.11
Counter for how many times the selected threshold has reached its setting value.
OBJECT-TYPE    
  Counter  

s3EnetThreshDuration 1.3.6.1.4.1.45.1.3.2.8.1.1.12
Length of window over which threshold counts are summed, specified in intervals of 500 TimeTicks (i.e., 5 seconds). This window is broken down into 5 second sampling periods for purposes of checking the threshold conditions, and determining when the actions specified need to take place when the condition occurs. If this object is written with a value that is not evenly divisible by 500, the agent will internally round the value up to the closest integral of 500 before it is used in threshold calculations (i.e., a value of 12 can be written, but will be interpreted as 15). Notes: 1.) A value of zero indicates an infinite duration window if the value of s3EnetThreshCondition is crossValue(2) or overValue(3). 2.) If the value of s3EnetThreshCondition is overRate(4) or overRatio(5), a value of zero is equivalent to a duration window of 5 seconds. 3.) If the value of s3EnetThreshType is linkStatus(12), this value of this object is ignore and assumed to be infinite.
OBJECT-TYPE    
  TimeTicks  

s3EnetThreshTableSize 1.3.6.1.4.1.45.1.3.2.8.2
The maximum number of entries in the table s3EnetThreshTable.
OBJECT-TYPE    
  INTEGER  

s3EnetSdTrafTable 1.3.6.1.4.1.45.1.3.2.9.1
This table contains a list of entries which provide SA-DA traffic information. Specifically frame and byte counter values are provided per unique SA-DA pair. The indexing scheme of this table allows an SA list to be retrieved using GETNEXT. An SA list is a list of entries that have a common SA, however, different DAs.
OBJECT-TYPE    
  SEQUENCE OF  
    S3EnetSdTrafEntry

s3EnetSdTrafEntry 1.3.6.1.4.1.45.1.3.2.9.1.1
An entry in the SA-DA traffic table.
OBJECT-TYPE    
  S3EnetSdTrafEntry  

s3EnetSdTrafMacSA 1.3.6.1.4.1.45.1.3.2.9.1.1.1
Source MAC address.
OBJECT-TYPE    
  PhysAddress Size(6)  

s3EnetSdTrafMacDA 1.3.6.1.4.1.45.1.3.2.9.1.1.2
Destination MAC address.
OBJECT-TYPE    
  PhysAddress Size(6)  

s3EnetSdTrafFrames 1.3.6.1.4.1.45.1.3.2.9.1.1.3
The number of good frames received by the concentrator for a SA-DA pair.
OBJECT-TYPE    
  Counter  

s3EnetSdTrafBytes 1.3.6.1.4.1.45.1.3.2.9.1.1.4
The number of bytes in good frames received by the concentrator for a SA-DA pair.
OBJECT-TYPE    
  Counter  

s3EnetDsTrafTable 1.3.6.1.4.1.45.1.3.2.9.2
This table contains a list of entries which provide DA-SA traffic information. Specifically frame and byte counter values are provided per unique DA-SA pair. The indexing scheme of this table allows a DA list to be retrieved using GETNEXT. A DA list is a list of entries that have a common DA, however, different SAs.
OBJECT-TYPE    
  SEQUENCE OF  
    S3EnetDsTrafEntry

s3EnetDsTrafEntry 1.3.6.1.4.1.45.1.3.2.9.2.1
An entry in the DA-SA table.
OBJECT-TYPE    
  S3EnetDsTrafEntry  

s3EnetDsTrafMacDA 1.3.6.1.4.1.45.1.3.2.9.2.1.1
Destination MAC address.
OBJECT-TYPE    
  PhysAddress Size(6)  

s3EnetDsTrafMacSA 1.3.6.1.4.1.45.1.3.2.9.2.1.2
Source MAC address.
OBJECT-TYPE    
  PhysAddress Size(6)  

s3EnetDsTrafFrames 1.3.6.1.4.1.45.1.3.2.9.2.1.3
The number of good frames received by the concentrator for a DA-SA pair.
OBJECT-TYPE    
  Counter  

s3EnetDsTrafBytes 1.3.6.1.4.1.45.1.3.2.9.2.1.4
The number of bytes in good frames received by the concentrator for a DA-SA pair.
OBJECT-TYPE    
  Counter  

s3EnetPagedTrafTable 1.3.6.1.4.1.45.1.3.2.9.3
This table contains a list of entries for the 'paged' Traffic Matrix table.
OBJECT-TYPE    
  SEQUENCE OF  
    S3EnetPagedTrafEntry

s3EnetPagedTrafEntry 1.3.6.1.4.1.45.1.3.2.9.3.1
A 'paged' entry in the Traffic Matrix table.
OBJECT-TYPE    
  S3EnetPagedTrafEntry  

s3EnetTrafPageNo 1.3.6.1.4.1.45.1.3.2.9.3.1.1
A specific page in the Traffic Matrix table.
OBJECT-TYPE    
  INTEGER  

s3EnetTrafPageEntries 1.3.6.1.4.1.45.1.3.2.9.3.1.2
This OCTET STRING contains up to 20 valid Traffic Matrix table entries. The entries will not be in any logical order. Each entry consists of a 20-byte octet string including a 6-byte source MAC address, a 6-byte destination MAC address, a received good frame count, and a byte count in good frames received. The counters are 4-bytes each where the first one is high-order byte and the last one is low-order byte.
OBJECT-TYPE    
  OCTET STRING Size(1..400)  

s3EnetTrafAgeInterval 1.3.6.1.4.1.45.1.3.2.9.4
The time used for aging of the nodes in tables s3EnetSdTrafTable and s3EnetDsTrafTable. Once a node has completely aged it will be removed from these tables. Note: Agents that do not implement this object (i.e., agents prior to version 5.3) use the object s3EnetNodeAgeInterval to perform this function.
OBJECT-TYPE    
  TimeTicks  

s3EnetPlusPortTable 1.3.6.1.4.1.45.1.3.2.10.1
This table provides a list of entries, each entry providing information related to frame MAC level error conditions per port. This table is conceptually an extension to the s3EnetPortTable and is only implemented by the 3313S and 3314S NMMs.
OBJECT-TYPE    
  SEQUENCE OF  
    S3EnetPlusPortEntry

s3EnetPlusPortEntry 1.3.6.1.4.1.45.1.3.2.10.1.1
An entry in the Plus Port table.
OBJECT-TYPE    
  S3EnetPlusPortEntry  

s3EnetPlusPortBoardIndex 1.3.6.1.4.1.45.1.3.2.10.1.1.1
A unique value for each board. Its value ranges between 1 and 12. (This is the slot number.)
OBJECT-TYPE    
  INTEGER  

s3EnetPlusPortIndex 1.3.6.1.4.1.45.1.3.2.10.1.1.2
A unique value for each port. Its value typically ranges between 1 and 12.
OBJECT-TYPE    
  INTEGER  

s3EnetPortFragments 1.3.6.1.4.1.45.1.3.2.10.1.1.3
This contains a count of fragments received by the board between 80-512 bits (64 bytes), inclusively, with invalid FCS or alignment errors. (These commonly represent collision fragments, and are not errors. Collision fragments were called FragErrors in the rev 3.x MIB, and were counted only on a per-board basis.)
OBJECT-TYPE    
  Counter  

s3EnetPortShortEvents 1.3.6.1.4.1.45.1.3.2.10.1.1.4
This contains a count of fragments received by the port shorter than 80 bits.
OBJECT-TYPE    
  Counter  

s3EnetPortAutoPartitions 1.3.6.1.4.1.45.1.3.2.10.1.1.5
This contains a count of times the ports on the board have autopartitioned due to excessive collisions (more than 32 consecutive collisions). This count is an approximation and may be less than the total count.
OBJECT-TYPE    
  Counter  

s3EnetPortRateMismatches 1.3.6.1.4.1.45.1.3.2.10.1.1.6
This contains a count of the occurrences of out of spec bit rates. This indicates the number of times FIFO buffer over-runs or underruns due to transmission rate errors.
OBJECT-TYPE    
  Counter  

s3EnetPortJabbers 1.3.6.1.4.1.45.1.3.2.10.1.1.7
This contains a count of the times that MAU jabber lockup protection (MJLP) was invoked because transmission of data from this port exceeded 5 msec in duration. This information can be useful in identifying faulty stations.
OBJECT-TYPE    
  Counter  

s3EnetPortLastSrcAddr 1.3.6.1.4.1.45.1.3.2.10.1.1.8
This is the source address of the last packet received through this port.
OBJECT-TYPE    
  PhysAddress Size(6)  

s3EnetPortSrcAddrChanges 1.3.6.1.4.1.45.1.3.2.10.1.1.9
This is the number of times that the s3EnetPortLastSrcAddr object for this has changed.
OBJECT-TYPE    
  Counter  

s3EnetPlusBoardTable 1.3.6.1.4.1.45.1.3.2.10.2
This table provides a list of entries, each entry providing information related to frame MAC level error conditions per board. This table is conceptually an extension to the s3EnetboardTable and is only implemented by the 3313S and 3314S NMMs.
OBJECT-TYPE    
  SEQUENCE OF  
    S3EnetPlusBoardEntry

s3EnetPlusBoardEntry 1.3.6.1.4.1.45.1.3.2.10.2.1
An entry in the Plus Board table.
OBJECT-TYPE    
  S3EnetPlusBoardEntry  

s3EnetPlusBoardIndex 1.3.6.1.4.1.45.1.3.2.10.2.1.1
The board number part of an index.
OBJECT-TYPE    
  INTEGER  

s3EnetBoardFragments 1.3.6.1.4.1.45.1.3.2.10.2.1.2
This contains a count of fragments received by the board between 80-512 bits (64 bytes), inclusively, with invalid FCS or alignment errors. (These commonly represent collision fragments, and are not errors. Collision fragments were called FragErrors in the rev 3.x MIB, and were counted only on a per-concentrator basis.)
OBJECT-TYPE    
  Counter  

s3EnetBoardShortEvents 1.3.6.1.4.1.45.1.3.2.10.2.1.3
This contains a count of fragments received by the board shorter than 80 bits.
OBJECT-TYPE    
  Counter  

s3EnetBoardAutoPartitions 1.3.6.1.4.1.45.1.3.2.10.2.1.4
This contains a count of times the ports on this board have been autopartitioned due to excessive collisions (more than 32 consecutive collisions). This count is an approximation and may be less than the total count.
OBJECT-TYPE    
  Counter  

s3EnetBoardRateMismatches 1.3.6.1.4.1.45.1.3.2.10.2.1.5
This contains a count of the occurrences of out of spec bit rates. This indicates the number of times FIFO buffer over-runs or underruns due to transmission rate errors.
OBJECT-TYPE    
  Counter  

s3EnetBoardJabbers 1.3.6.1.4.1.45.1.3.2.10.2.1.6
This contains a count of the times that MAU jabber lockup protection (MJLP) was invoked because transmission of data from a port on this board exceeded 5 msec in duration. This information can be useful in identifying faulty stations.
OBJECT-TYPE    
  Counter  

s3EnetConcShortEvents 1.3.6.1.4.1.45.1.3.2.10.3.1
This contains a count of fragments received by the concentrator shorter than 80 bits.
OBJECT-TYPE    
  Counter  

s3EnetConcAutoPartitions 1.3.6.1.4.1.45.1.3.2.10.3.2
This contains a count of times the ports on this concentrator have been autopartitioned due to excessive collisions (more than 32 consecutive collisions). This count is based on a one-bit counter (flag) per port in the host modules, and will not always represent the total count.
OBJECT-TYPE    
  Counter  

s3EnetConcRateMismatches 1.3.6.1.4.1.45.1.3.2.10.3.3
This contains a count of the occurrences of out of spec bit rates. This indicates the number of times FIFO buffer over-runs or underruns due to transmission rate errors.
OBJECT-TYPE    
  Counter  

s3EnetConcJabbers 1.3.6.1.4.1.45.1.3.2.10.3.4
This contains a count of the times that MAU jabber lockup protection (MJLP) was invoked because transmission of data from a port on this concentrator exceeded 5 msec in duration. This information can be useful in identifying faulty stations.
OBJECT-TYPE    
  Counter  

s3EnetConcCollBackoffErrors 1.3.6.1.4.1.45.1.3.2.10.3.5
This contains a total concentrator count of the collision events that occur during the normal collision window (i.e., the collisions is not a late collision) and do not have a runt error.
OBJECT-TYPE    
  Counter  

s3EnetFrSizePortTable 1.3.6.1.4.1.45.1.3.2.11.1
This table provides a list of entries, each entry providing information related to frame sizes of packets received on a port. The variables defined for the entries are only supported by 3313S and 3314S NMM.
OBJECT-TYPE    
  SEQUENCE OF  
    S3EnetFrSizePortEntry

s3EnetFrSizePortEntry 1.3.6.1.4.1.45.1.3.2.11.1.1
An entry in the FrSize Port table.
OBJECT-TYPE    
  S3EnetFrSizePortEntry  

s3EnetFrSizePortBoardIndex 1.3.6.1.4.1.45.1.3.2.11.1.1.1
A unique value for each board. Its value ranges between 1 and 12. (This is the slot number.)
OBJECT-TYPE    
  INTEGER  

s3EnetFrSizePortIndex 1.3.6.1.4.1.45.1.3.2.11.1.1.2
A unique value for each port. Its value typically ranges between 1 and 12.
OBJECT-TYPE    
  INTEGER  

s3EnetFrSizePort64to127 1.3.6.1.4.1.45.1.3.2.11.1.1.3
This contains a count of frames received by the port that are in the range of 64 octets to 127 octets, inclusive.
OBJECT-TYPE    
  Counter  

s3EnetFrSizePort128to255 1.3.6.1.4.1.45.1.3.2.11.1.1.4
This contains a count of frames received by the port that are in the range of 128 octets to 255 octets, inclusive.
OBJECT-TYPE    
  Counter  

s3EnetFrSizePort256to511 1.3.6.1.4.1.45.1.3.2.11.1.1.5
This contains a count of frames received by the port that are in the range of 256 octets to 511 octets, inclusive.
OBJECT-TYPE    
  Counter  

s3EnetFrSizePort512to1023 1.3.6.1.4.1.45.1.3.2.11.1.1.6
This contains a count of frames received by the port that are in the range of 512 octets to 1023 octets, inclusive.
OBJECT-TYPE    
  Counter  

s3EnetFrSizePort1024to1518 1.3.6.1.4.1.45.1.3.2.11.1.1.7
This contains a count of frames received by the port that are in the range of 1024 octets to 1518 octets, inclusive.
OBJECT-TYPE    
  Counter  

s3EnetFrSizeBoardTable 1.3.6.1.4.1.45.1.3.2.11.2
This table provides a list of entries, each entry providing information related to frame MAC level error conditions per board. The variables defined for the entries are only supported by 3313S and 3314S NMMs. The use of any variable in this table for other NMMs will cause the NMMs to return noSuchName error status in the response.
OBJECT-TYPE    
  SEQUENCE OF  
    S3EnetFrSizeBoardEntry

s3EnetFrSizeBoardEntry 1.3.6.1.4.1.45.1.3.2.11.2.1
An entry in the FrSize Board table.
OBJECT-TYPE    
  S3EnetFrSizeBoardEntry  

s3EnetFrSizeBoardIndex 1.3.6.1.4.1.45.1.3.2.11.2.1.1
A unique value for each board. Its value ranges between 1 and 12. (This is the slot number.)
OBJECT-TYPE    
  INTEGER  

s3EnetFrSizeBoard64to127 1.3.6.1.4.1.45.1.3.2.11.2.1.2
This contains a count of frames received by the board that are in the range of 64 octets to 127 octets, inclusive.
OBJECT-TYPE    
  Counter  

s3EnetFrSizeBoard128to255 1.3.6.1.4.1.45.1.3.2.11.2.1.3
This contains a count of frames received by the board that are in the range of 128 octets to 255 octets, inclusive.
OBJECT-TYPE    
  Counter  

s3EnetFrSizeBoard256to511 1.3.6.1.4.1.45.1.3.2.11.2.1.4
This contains a count of frames received by the board that are in the range of 256 octets to 511 octets, inclusive.
OBJECT-TYPE    
  Counter  

s3EnetFrSizeBoard512to1023 1.3.6.1.4.1.45.1.3.2.11.2.1.5
This contains a count of frames received by the board that are in the range of 512 octets to 1023 octets, inclusive.
OBJECT-TYPE    
  Counter  

s3EnetFrSizeBoard1024to1518 1.3.6.1.4.1.45.1.3.2.11.2.1.6
This contains a count of frames received by the board that are in the range of 1024 octets to 1518 octets, inclusive.
OBJECT-TYPE    
  Counter  

s3EnetFrSizeConc64to127 1.3.6.1.4.1.45.1.3.2.11.3.1
This contains a count of frames received by the concentrator that are in the range of 64 octets to 127 octets, inclusive.
OBJECT-TYPE    
  Counter  

s3EnetFrSizeConc128to255 1.3.6.1.4.1.45.1.3.2.11.3.2
This contains a count of frames received by the concentrator that are in the range of 128 octets to 255 octets, inclusive.
OBJECT-TYPE    
  Counter  

s3EnetFrSizeConc256to511 1.3.6.1.4.1.45.1.3.2.11.3.3
This contains a count of frames received by the concentrator that are in the range of 256 octets to 511 octets, inclusive.
OBJECT-TYPE    
  Counter  

s3EnetFrSizeConc512to1023 1.3.6.1.4.1.45.1.3.2.11.3.4
This contains a count of frames received by the concentrator that are in the range of 512 octets to 1023 octets, inclusive.
OBJECT-TYPE    
  Counter  

s3EnetFrSizeConc1024to1518 1.3.6.1.4.1.45.1.3.2.11.3.5
This contains a count of frames received by the concentrator that are in the range of 1024 octets to 1518 octets, inclusive.
OBJECT-TYPE    
  Counter  

s3EnetProtoPortTable 1.3.6.1.4.1.45.1.3.2.12.1
This table provides a list of entries, each entry providing information related to packet protocol type distributions per port. The variables defined for the entries are only supported by 3313S and 3314S NMMs. The use of any variable in this table for other NMMs will cause the NMMs to return noSuchName error status in the response.
OBJECT-TYPE    
  SEQUENCE OF  
    S3EnetProtoPortEntry

s3EnetProtoPortEntry 1.3.6.1.4.1.45.1.3.2.12.1.1
An entry in the Proto Port table.
OBJECT-TYPE    
  S3EnetProtoPortEntry  

s3EnetProtoPortBoardIndex 1.3.6.1.4.1.45.1.3.2.12.1.1.1
A unique value for each board. Its value ranges between 1 and 12. (This is the slot number.)
OBJECT-TYPE    
  INTEGER  

s3EnetProtoPortIndex 1.3.6.1.4.1.45.1.3.2.12.1.1.2
A unique value for each port. Its value typically ranges between 1 and 12.
OBJECT-TYPE    
  INTEGER  

s3EnetProtoPort8023Frames 1.3.6.1.4.1.45.1.3.2.12.1.1.3
This contains a count of frames received by the port that are of 802.3 type.
OBJECT-TYPE    
  Counter  

s3EnetProtoPortEthernetFrames 1.3.6.1.4.1.45.1.3.2.12.1.1.4
This contains a count of frames received by the port that are of Ethernet type.
OBJECT-TYPE    
  Counter  

s3EnetProtoPortOtherFrames 1.3.6.1.4.1.45.1.3.2.12.1.1.5
This contains a count of frames received by the port that are of types not counted by individual counters below.
OBJECT-TYPE    
  Counter  

s3EnetProtoPortSnaFrames 1.3.6.1.4.1.45.1.3.2.12.1.1.6
This contains a count of frames received by the port that are of SNA type.
OBJECT-TYPE    
  Counter  

s3EnetProtoPortIpFrames 1.3.6.1.4.1.45.1.3.2.12.1.1.7
This contains a count of frames received by the port that are of IP type.
OBJECT-TYPE    
  Counter  

s3EnetProtoPortIsoFrames 1.3.6.1.4.1.45.1.3.2.12.1.1.8
This contains a count of frames received by the port that are of ISO type.
OBJECT-TYPE    
  Counter  

s3EnetProtoPortArpFrames 1.3.6.1.4.1.45.1.3.2.12.1.1.9
This contains a count of frames received by the port that are of ARP type.
OBJECT-TYPE    
  Counter  

s3EnetProtoPortDecIVFrames 1.3.6.1.4.1.45.1.3.2.12.1.1.10
This contains a count of frames received by the port that are of DECIV type.
OBJECT-TYPE    
  Counter  

s3EnetProtoPortDecLatFrames 1.3.6.1.4.1.45.1.3.2.12.1.1.11
This contains a count of frames received by the port that are of DECLAT type.
OBJECT-TYPE    
  Counter  

s3EnetProtoPortEthTalkFrames 1.3.6.1.4.1.45.1.3.2.12.1.1.12
This contains a count of frames received by the port that are of EtherTalk type.
OBJECT-TYPE    
  Counter  

s3EnetProtoPortXnsFrames 1.3.6.1.4.1.45.1.3.2.12.1.1.13
This contains a count of frames received by the port that are of XNS type.
OBJECT-TYPE    
  Counter  

s3EnetProtoPortIpxFrames 1.3.6.1.4.1.45.1.3.2.12.1.1.14
This contains a count of frames received by the port that are of IPX type.
OBJECT-TYPE    
  Counter  

s3EnetProtoPortDecLavcFrames 1.3.6.1.4.1.45.1.3.2.12.1.1.15
This contains a count of frames received by the port that are of DEC LAVC type.
OBJECT-TYPE    
  Counter  

s3EnetProtoPortNetBiosFrames 1.3.6.1.4.1.45.1.3.2.12.1.1.16
This contains a count of frames received by the port that are of NETBIOS type.
OBJECT-TYPE    
  Counter  

s3EnetProtoPortBrdgSpanTreeFrames 1.3.6.1.4.1.45.1.3.2.12.1.1.17
This contains a count of frames received by the port that are of Bridge Spanning Tree type.
OBJECT-TYPE    
  Counter  

s3EnetProtoBoardTable 1.3.6.1.4.1.45.1.3.2.12.2
This table provides a list of entries, each entry providing information related to packet protocol type distribution per board. The variables defined for the entries are only supported by 3313S and 3314S NMMs. The use of any variable in this table for other NMMs will cause the NMMs to return noSuchName error status in the response.
OBJECT-TYPE    
  SEQUENCE OF  
    S3EnetProtoBoardEntry

s3EnetProtoBoardEntry 1.3.6.1.4.1.45.1.3.2.12.2.1
An entry in the Proto Board table.
OBJECT-TYPE    
  S3EnetProtoBoardEntry  

s3EnetProtoBoardIndex 1.3.6.1.4.1.45.1.3.2.12.2.1.1
A unique value for each board. Its value ranges between 1 and 12. (This is the slot number.)
OBJECT-TYPE    
  INTEGER  

s3EnetProtoBoard8023Frames 1.3.6.1.4.1.45.1.3.2.12.2.1.2
This contains a count of frames received by the board that are of 802.3 type.
OBJECT-TYPE    
  Counter  

s3EnetProtoBoardEthernetFrames 1.3.6.1.4.1.45.1.3.2.12.2.1.3
This contains a count of frames received by the board that are of Ethernet type.
OBJECT-TYPE    
  Counter  

s3EnetProtoBoardOtherFrames 1.3.6.1.4.1.45.1.3.2.12.2.1.4
This contains a count of frames received by the board that are of types not specified below.
OBJECT-TYPE    
  Counter  

s3EnetProtoBoardSnaFrames 1.3.6.1.4.1.45.1.3.2.12.2.1.5
This contains a count of frames received by the board that are of SNA type.
OBJECT-TYPE    
  Counter  

s3EnetProtoBoardIpFrames 1.3.6.1.4.1.45.1.3.2.12.2.1.6
This contains a count of frames received by the board that are of IP type.
OBJECT-TYPE    
  Counter  

s3EnetProtoBoardIsoFrames 1.3.6.1.4.1.45.1.3.2.12.2.1.7
This contains a count of frames received by the board that are of ISO type.
OBJECT-TYPE    
  Counter  

s3EnetProtoBoardArpFrames 1.3.6.1.4.1.45.1.3.2.12.2.1.8
This contains a count of frames received by the board that are of ARP type.
OBJECT-TYPE    
  Counter  

s3EnetProtoBoardDecIVFrames 1.3.6.1.4.1.45.1.3.2.12.2.1.9
This contains a count of frames received by the board that are of DECIV type.
OBJECT-TYPE    
  Counter  

s3EnetProtoBoardDecLatFrames 1.3.6.1.4.1.45.1.3.2.12.2.1.10
This contains a count of frames received by the board that are of DECLAT type.
OBJECT-TYPE    
  Counter  

s3EnetProtoBoardEthTalkFrames 1.3.6.1.4.1.45.1.3.2.12.2.1.11
This contains a count of frames received by the board that are of EtherTalk type.
OBJECT-TYPE    
  Counter  

s3EnetProtoBoardXnsFrames 1.3.6.1.4.1.45.1.3.2.12.2.1.12
This contains a count of frames received by the board that are of XNS type.
OBJECT-TYPE    
  Counter  

s3EnetProtoBoardIpxFrames 1.3.6.1.4.1.45.1.3.2.12.2.1.13
This contains a count of frames received by the board that are of IPX type.
OBJECT-TYPE    
  Counter  

s3EnetProtoBoardDecLavcFrames 1.3.6.1.4.1.45.1.3.2.12.2.1.14
This contains a count of frames received by the board that are of DEC LAVC type.
OBJECT-TYPE    
  Counter  

s3EnetProtoBoardNetBiosFrames 1.3.6.1.4.1.45.1.3.2.12.2.1.15
This contains a count of frames received by the board that are of NETBIOS type.
OBJECT-TYPE    
  Counter  

s3EnetProtoBoardBrdgSpanTreeFrames 1.3.6.1.4.1.45.1.3.2.12.2.1.16
This contains a count of frames received by the board that are of Bridge Spanning Tree type.
OBJECT-TYPE    
  Counter  

s3EnetProtoConc8023Frames 1.3.6.1.4.1.45.1.3.2.12.3.1
This contains a count of frames received by the concentrator that are of 802.3 type.
OBJECT-TYPE    
  Counter  

s3EnetProtoConcEthernetFrames 1.3.6.1.4.1.45.1.3.2.12.3.2
This contains a count of frames received by the concentrator that are of Ethernet type.
OBJECT-TYPE    
  Counter  

s3EnetProtoConcOtherFrames 1.3.6.1.4.1.45.1.3.2.12.3.3
This contains a count of frames received by the concentrator that are of types not specified below.
OBJECT-TYPE    
  Counter  

s3EnetProtoConcSnaFrames 1.3.6.1.4.1.45.1.3.2.12.3.4
This contains a count of frames received by the concentrator that are of SNA type.
OBJECT-TYPE    
  Counter  

s3EnetProtoConcIpFrames 1.3.6.1.4.1.45.1.3.2.12.3.5
This contains a count of frames received by the concentrator that are of IP type.
OBJECT-TYPE    
  Counter  

s3EnetProtoConcIsoFrames 1.3.6.1.4.1.45.1.3.2.12.3.6
This contains a count of frames received by the concentrator that are of ISO type.
OBJECT-TYPE    
  Counter  

s3EnetProtoConcArpFrames 1.3.6.1.4.1.45.1.3.2.12.3.7
This contains a count of frames received by the concentrator that are of ARP type.
OBJECT-TYPE    
  Counter  

s3EnetProtoConcDecIVFrames 1.3.6.1.4.1.45.1.3.2.12.3.8
This contains a count of frames received by the concentrator that are of DECIV type.
OBJECT-TYPE    
  Counter  

s3EnetProtoConcDecLatFrames 1.3.6.1.4.1.45.1.3.2.12.3.9
This contains a count of frames received by the concentrator that are of DECLAT type.
OBJECT-TYPE    
  Counter  

s3EnetProtoConcEthTalkFrames 1.3.6.1.4.1.45.1.3.2.12.3.10
This contains a count of frames received by the concentrator that are of EtherTalk type.
OBJECT-TYPE    
  Counter  

s3EnetProtoConcXnsFrames 1.3.6.1.4.1.45.1.3.2.12.3.11
This contains a count of frames received by the concentrator that are of XNS type.
OBJECT-TYPE    
  Counter  

s3EnetProtoConcIpxFrames 1.3.6.1.4.1.45.1.3.2.12.3.12
This contains a count of frames received by the concentrator that are of IPX type.
OBJECT-TYPE    
  Counter  

s3EnetProtoConcDecLavcFrames 1.3.6.1.4.1.45.1.3.2.12.3.13
This contains a count of frames received by the concentrator that are of DEC LAVC type.
OBJECT-TYPE    
  Counter  

s3EnetProtoConcNetBiosFrames 1.3.6.1.4.1.45.1.3.2.12.3.14
This contains a count of frames received by the concentrator that are of NETBIOS type.
OBJECT-TYPE    
  Counter  

s3EnetProtoConcBrdgSpanTreeFrames 1.3.6.1.4.1.45.1.3.2.12.3.15
This contains a count of frames received by the concentrator that are of Bridge Spanning Tree type.
OBJECT-TYPE    
  Counter  

s3EnetHostTableSize 1.3.6.1.4.1.45.1.3.2.13.1
The current number of entries in table s3EnetHostTable.
OBJECT-TYPE    
  INTEGER 0..65535  

s3EnetHostLastDeleteTime 1.3.6.1.4.1.45.1.3.2.13.2
The value of sysUpTime when the last entry was deleted from table s3EnetHostTable due to a shortage of resources. If no deletions have occurred, then the value is zero.
OBJECT-TYPE    
  TimeTicks  

s3EnetHostTable 1.3.6.1.4.1.45.1.3.2.13.3
A Table containing MAC/Network address pairs that have been detected on the segment.
OBJECT-TYPE    
  SEQUENCE OF  
    S3EnetHostEntry

s3EnetHostEntry 1.3.6.1.4.1.45.1.3.2.13.3.1
A row in the table of MAC/Network address pairs. Entries can not be created or deleted via SNMP operations. New entries are added when a new MAC/Network address pair is detected. An entry is removed to add a new entry when the table is full. The entry that is removed is the one that has been least recently observed.
OBJECT-TYPE    
  S3EnetHostEntry  

s3EnetHostIndex 1.3.6.1.4.1.45.1.3.2.13.3.1.1
The index of the MAC/Network address pair. The value is between 1 and N, where N is the value of s3EnetHostTableSize. The association of this index to a pair may change when a pair is removed from the table due to a resource shortage. s3EnetHostLastDeleteTime must be monitored to determine when this condition has occured.
OBJECT-TYPE    
  INTEGER 1..65535  

s3EnetHostObserveOrder 1.3.6.1.4.1.45.1.3.2.13.3.1.2
The relative ordering of the MAC/Network adddress pair. There is a global value that starts at 1 and increases by one for each observation of an address pair. When the maximum value of 65535 is reached, the next value will be 1. The global value is used to update this object each time the MAC/Network address pair is observed (and when the entry is initially created). Since the global value starts over again after it reaches its maximum value, there may be more than one entry that has the same value.
OBJECT-TYPE    
  INTEGER 1..65535  

s3EnetHostNetAddr 1.3.6.1.4.1.45.1.3.2.13.3.1.3
The network address (in network order) of the MAC/Network address pair.
OBJECT-TYPE    
  OCTET STRING  

s3EnetHostAddrType 1.3.6.1.4.1.45.1.3.2.13.3.1.4
The type of address that is stored in the object s3EnetHostNetAddr for this entry. The values are: other(1)...Unknown type ip(2)......IP address ipx(3).....IPX address
OBJECT-TYPE    
  INTEGER other(1), ip(2), ipx(3)  

s3EnetHostMacAddress 1.3.6.1.4.1.45.1.3.2.13.3.1.5
The MAC address (in canonical order) of the MAC/Network address pair.
OBJECT-TYPE    
  PhysAddress Size(6)  

s3EnetHostSlotIndex 1.3.6.1.4.1.45.1.3.2.13.3.1.6
The board index that the host is connected through.
OBJECT-TYPE    
  INTEGER  

s3EnetHostPortIndex 1.3.6.1.4.1.45.1.3.2.13.3.1.7
The port index that the host is connected through.
OBJECT-TYPE    
  INTEGER  

s3EnetHostLearnMethod 1.3.6.1.4.1.45.1.3.2.13.3.1.8
Indicates the method that was used to discover the MAC/Network address pair. The methods that can be used for discovery are shown below. other(1).........Indicates an unknown discovery method. arpRequest(2)....Indicates that ARP request packets were used for discovery. arpResponse(3)...Indicates that ARP response packets were used for discovery. ripRequest(4)....Indicates that RIP request packets were used for discovery. ripResponse(5)...Indicates that RIP response packets were used for discovery.
OBJECT-TYPE    
  INTEGER other(1), arpRequest(2), arpResponse(3), ripRequest(4), ripResponse(5)  

s3EnetHostTimeStamp 1.3.6.1.4.1.45.1.3.2.13.3.1.9
The value of sysUpTime when the MAC/Network address pair was last observed on the segment.
OBJECT-TYPE    
  TimeTicks