SYMBOL-DSSS-ENTERPRISE-PRIVATE-MIB

File: SYMBOL-DSSS-ENTERPRISE-PRIVATE-MIB.mib (148080 bytes)

Imported modules

RFC1155-SMI RFC-1212 RFC1213-MIB
RFC-1215

Imported symbols

enterprises IpAddress Counter
Gauge TimeTicks OBJECT-TYPE
snmp DisplayString PhysAddress
TRAP-TYPE

Defined Types

WEPKeytype128b  
OCTET STRING Size(13)    

ApAdditionalGatewaysEntry  
SEQUENCE    
  additionalGatewaysIndex INTEGER
  apAdditionalGatewaysIPAddr IpAddress

ApAddrFilterEntry  
SEQUENCE    
  disallowedIndex INTEGER
  disallowedMU PhysAddress

ApTypeFilterEntry  
SEQUENCE    
  typeIndex INTEGER
  etherType OCTET STRING

ApWEPKeyEntry  
SEQUENCE    
  ap128bWepkeyIndex INTEGER
  ap128bWepKeyValue WEPKeytype128b

ApTrafficMatrixEntry  
SEQUENCE    
  apTMTableIndex INTEGER
  apProtoItfName DisplayString
  apNPktsToEnets Counter
  apNPktsToPpps Counter
  apNPktsToRfs Counter
  apNPktsToAPStks Counter

ApItfStatEntry  
SEQUENCE    
  apItfStatIndex INTEGER
  apInterfaceName DisplayString
  apPacketsIns Counter
  apPacketsOuts Counter
  apOctetsIns Counter
  apOctetsOuts Counter
  apPktsInPerSec Gauge
  apPktsOutPerSec Gauge
  apOctInPerSec Gauge
  apOctOutPerSec Gauge

ApMUEntry  
SEQUENCE    
  muIndex INTEGER
  muMacAddr PhysAddress
  muInterface INTEGER
  muState INTEGER
  muPowerMode INTEGER
  muStationID INTEGER
  muLastAPAddr PhysAddress
  muTotalAssoc INTEGER
  muAssocStart TimeTicks
  muLstAssStrt TimeTicks
  muLastAssEnd TimeTicks
  muNPktsSents Counter
  muNPktsRcvds Counter
  muNBytesSents Counter
  muNBytesRcvds Counter
  muNDiscdPkts Counter
  muTmLastData TimeTicks
  muPriority INTEGER
  muSupportedRates INTEGER
  muCurrentXmtRate INTEGER
  muLastActivity TimeTicks

ApMUHATEntry  
SEQUENCE    
  muHATMUIpAddr IpAddress
  muHATFrAgIpAddr IpAddress

ApMUFATEntry  
SEQUENCE    
  muFATMUIpAddr IpAddress
  muFATHmAgIpAddr IpAddress

ApKnownAPsEntry  
SEQUENCE    
  apAPMacAddr PhysAddress
  apAPIpAddr IpAddress
  apHoppingSet INTEGER
  apHoppingSeq INTEGER
  apNbrOfMUs INTEGER
  apKBIOS INTEGER
  apAway INTEGER
  ap802dot11Protocol INTEGER
  apFwVer DisplayString
  apDSchannel INTEGER

ApWLAPItfEntry  
SEQUENCE    
  apWLAPItfID OCTET STRING
  apWLAPItfAddr PhysAddress
  apWLAPItfState INTEGER
  apWLAPPathCost INTEGER
  apDsgnatedRoot OCTET STRING
  apDsgnatedCost INTEGER
  apDsgnatedWLAP OCTET STRING
  apDsgnatedItf OCTET STRING

ApRetryHistogramEntry  
SEQUENCE    
  apRetryHistogramIndex INTEGER
  apNumberOfRetries INTEGER
  apPacketsHistogramCounts Counter

ApDSPerFreqStatEntry  
SEQUENCE    
  rfDSFrequency INTEGER
  rfDSPerFqPktsSents Counter
  rfDSPerFqPktsRcvds Counter
  rfDSPerFqRetries Counter

ApAccCtrlEntry  
SEQUENCE    
  allowedIndex INTEGER
  allowedMU PhysAddress

ApACLRangeEntry  
SEQUENCE    
  apACLRangeIndex INTEGER
  lowMacAddr PhysAddress
  highMacAddr PhysAddress

Defined Values

symbol 1.3.6.1.4.1.388
OBJECT IDENTIFIER    

spectrum24 1.3.6.1.4.1.388.1
OBJECT IDENTIFIER    

dsap 1.3.6.1.4.1.388.1.5
OBJECT IDENTIFIER    

apConfigMgmt 1.3.6.1.4.1.388.1.5.1
OBJECT IDENTIFIER    

apPerformMgmt 1.3.6.1.4.1.388.1.5.2
OBJECT IDENTIFIER    

apFaultMgmt 1.3.6.1.4.1.388.1.5.3
OBJECT IDENTIFIER    

apSecurityMgmt 1.3.6.1.4.1.388.1.5.4
OBJECT IDENTIFIER    

apManufactureInfo 1.3.6.1.4.1.388.1.5.1.1
OBJECT IDENTIFIER    

apSystemConfig 1.3.6.1.4.1.388.1.5.1.2
OBJECT IDENTIFIER    

apSNMPInfo 1.3.6.1.4.1.388.1.5.1.3
OBJECT IDENTIFIER    

apRFConfig 1.3.6.1.4.1.388.1.5.1.4
OBJECT IDENTIFIER    

apSerialPortConfig 1.3.6.1.4.1.388.1.5.1.5
OBJECT IDENTIFIER    

apEthernetStatistics 1.3.6.1.4.1.388.1.5.2.3
OBJECT IDENTIFIER    

apRFStatistics 1.3.6.1.4.1.388.1.5.2.4
OBJECT IDENTIFIER    

apSerialPortStatistics 1.3.6.1.4.1.388.1.5.2.6
OBJECT IDENTIFIER    

apWNMPStatistics 1.3.6.1.4.1.388.1.5.2.7
OBJECT IDENTIFIER    

apMUInfo 1.3.6.1.4.1.388.1.5.2.8
OBJECT IDENTIFIER    

apFilterStatistics 1.3.6.1.4.1.388.1.5.2.10
OBJECT IDENTIFIER    

apWLAPInfo 1.3.6.1.4.1.388.1.5.2.11
OBJECT IDENTIFIER    

apMobileIPStatistics 1.3.6.1.4.1.388.1.5.2.14
OBJECT IDENTIFIER    

coldStart 0
Access Point cold boot. - apMyMacAddr is the MAC address of the Access Point sending this trap message.
TRAP-TYPE    

authenticationFailure 4
Invalid SNMP Community string. - apMyMacAddr is the MAC address of the Access Point sending this trap message. - apAPMacAddr is the MAC address of the remote host sending SNMP packet with invalid community.
TRAP-TYPE    

apDSAPRFStartUpTrap 101
RF Driver is up. - apMyMacAddr is the MAC address of the Access Point sending this trap message.
TRAP-TYPE    

apDSAPACLViolationTrap 102
Mobile Unit MAC address not in the Access control Table. - apMyMacAddr is the MAC address of the Access Point sending this trap message. - muMacAddr is the MAC address of the Mobile Unit not in the Access Control Table.
TRAP-TYPE    

apDSAPMUAssocTrap 111
Indicates that there is one Mobile Unit associating with this Access Point. - apMyMacAddr is the MAC address of the Access Point sending this trap message. - muMacAddr is the MAC address of the Mobile Unit. Note : If two or more Mobile Units associate with the Access Point at the same time, muMacAddr belongs to the last Mobile Unit. - apCurrentMUs is the number of Mobile Units currently associating with this Access Point.
TRAP-TYPE    

apDSAPMUUnAssocTrap 112
Indicates that there is one Mobile Unit no longer associating with this Access Point anymore. - apMyMacAddr is the MAC address of the Access Point sending this trap message. - muMacAddr is the MAC address of the Mobile Unit. Note : If two or more Mobile Units un-associate with the Access Point at the same time, muMacAddr belongs to the last Mobile Unit. - apCurrentMUs is the number of Mobile Units currently associating with this Access Point.
TRAP-TYPE    

apDSAPMUMaxAssocTrap 116
Indicates that the number of MUs associated with this Access Point is at the threshold set by apMaxMUTrigger. - apMyMacAddr is the MAC address of the Access Point sending this trap message. - apCurrentMUs is the number of Mobile Units currently associating with this Access Point.
TRAP-TYPE    

apDSRootWLAPUpTrap 121
Indicates that the Root AP connection is setup and is ready to forward data. - apMyMacAddr is the MAC address of the Access Point sending this trap message. - apAPMacAddr is the MAC address of the Root AP. - apNbrOfWLAPItfs is the number of current WLAP Interfaces established.
TRAP-TYPE    

apDSRootWLAPLostTrap 122
If the current wireless AP does not receive Beacon packet from its Root AP within one second, it will consider the Root AP is lost. The wireless AP will eventually reset itself to re-establish the network topology. - apMyMacAddr is the MAC address of the Access Point sending this trap message. - apAPMacAddr is the MAC address of the Root AP. - apNbrOfWLAPItfs is the number of current WLAP Interfaces established.
TRAP-TYPE    

apDSDsgntedWLAPUpTrap 123
Indicates that the Designated WLAP connection is setup and is ready to forward data. - apMyMacAddr is the MAC address of the Access Point sending this trap message. - apAPMacAddr is the MAC address of the Designated WLAP. - apNbrOfWLAPItfs is the number of current WLAP Interfaces established.
TRAP-TYPE    

apDSDsgnatedWLAPLostTrap 124
If the current wireless AP does not receive Config BPDU (Bridge Protocol Data Unit) packet from its Designated WLAP for MAX AGE time, it will consider that the Designated WLAP is lost. - apMyMacAddr is the MAC address of the Access Point sending this trap message. - apAPMacAddr is the MAC address of the Designated WLAP. - apNbrOfWLAPItfs is the number of current WLAP Interfaces established.
TRAP-TYPE    

apDSAPDHCPConfigChgTrap 130
If there are any DHCP network configuration change, This trap will be issued. - apMyMacAddr is the MAC address of the Access Point sending this trap message.
TRAP-TYPE    

apDSAPDHCPLeaseUpTrap 131
If the Access point(Client) is unable to renew the DHCP lease before the lease is expired, this trap is generated. - apMyMacAddr is the MAC address of the Access Point sending this trap message.
TRAP-TYPE    

apModelnumber 1.3.6.1.4.1.388.1.5.1.1.1
The Model Number of the Access Point device.
Status: mandatory Access: read-only
OBJECT-TYPE    
  DisplayString Size(1..32)  

apSerialnumber 1.3.6.1.4.1.388.1.5.1.1.2
The Serial Number of the Access Point system.
Status: mandatory Access: read-only
OBJECT-TYPE    
  DisplayString Size(1..16)  

apHardwareRev 1.3.6.1.4.1.388.1.5.1.1.3
The current revision of the Access Point hardware.
Status: mandatory Access: read-only
OBJECT-TYPE    
  DisplayString Size(1..8)  

apMyMacAddr 1.3.6.1.4.1.388.1.5.1.1.4
The MAC address of the Access Point.
Status: mandatory Access: read-only
OBJECT-TYPE    
  PhysAddress  

apAPFirmwareRev 1.3.6.1.4.1.388.1.5.1.1.5
The current revision of the Access Point firmware.
Status: mandatory Access: read-only
OBJECT-TYPE    
  DisplayString Size(1..16)  

apRFFirmwareRev 1.3.6.1.4.1.388.1.5.1.1.6
The current revision of the Access Point radio firmware.
Status: mandatory Access: read-only
OBJECT-TYPE    
  DisplayString Size(0..16)  

apMfgDate 1.3.6.1.4.1.388.1.5.1.1.7
The Date this Access Point was manufactured.
Status: mandatory Access: read-only
OBJECT-TYPE    
  DisplayString Size(1..32)  

apHTMLFileRev 1.3.6.1.4.1.388.1.5.1.1.8
The current revision of the Access Point HTML file.
Status: mandatory Access: read-only
OBJECT-TYPE    
  DisplayString Size(1..8)  

apVendorID 1.3.6.1.4.1.388.1.5.1.1.9
Displays the Vendor ID of the vendor for which this AP has been manufactured for. The current values are: - Symbol (5) - 3Com (6) - Ericsson (8) - Intel (9)
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER symbol(5), threeCom(6), ericsson(8), intel(9)  

apUnitName 1.3.6.1.4.1.388.1.5.1.2.1
An ASCII string to identify this Access Point (up to 31 characters).
Status: mandatory Access: read-write
OBJECT-TYPE    
  DisplayString Size(1..31)  

apMyIPAddr 1.3.6.1.4.1.388.1.5.1.2.2
The IP address for the AP.
Status: mandatory Access: read-write
OBJECT-TYPE    
  IpAddress  

apSubnetMask 1.3.6.1.4.1.388.1.5.1.2.3
The IP subnet mask for the AP.
Status: mandatory Access: read-write
OBJECT-TYPE    
  IpAddress  

apGatewayIPAddr 1.3.6.1.4.1.388.1.5.1.2.4
The IP address for the default gateway.
Status: mandatory Access: read-write
OBJECT-TYPE    
  IpAddress  

apDefaultInterface 1.3.6.1.4.1.388.1.5.1.2.5
Specifies the default interface (Ethernet, PPP or WLAP) for the AP to forward an unknown packet. Default is ethernet(1).
Status: mandatory Access: read-write
OBJECT-TYPE    
  INTEGER ethernet(1), ppp(2), wlap(3)  

apEnetPortState 1.3.6.1.4.1.388.1.5.1.2.6
Specifies the state of the Ethernet interface. Default is up(1).
Status: mandatory Access: read-write
OBJECT-TYPE    
  INTEGER up(1), down(2)  

apEthernetTimeOut 1.3.6.1.4.1.388.1.5.1.2.7
If the value is: - 0: the Ethernet Time Out function is disabled. - 1: detect Ethernet timeout by hardware circuitry. - 30-255: Ethernet timeout is detected by software algorithm. When the Ethernet connection is broken and the WLAP mode is either enabled or disabled, the AP will clear the MU table and disable the RF interface until the Etherent connection is up. The following values are only valid when WLAP mode is enabled and it does not matter whetehr WLAP associates with the root AP or not. - 2: send WLAP Alive BPDU on Ethernet interface to let other WLAP on the same Ethernet segment to detect it's existence. - 3: keep track of WLAP Alive BPDU on Ethernet inter- face. If the BPDU is missing for 'WLAP Hello Time' seconds, the Ethernet Activity LEDs will flash and the RF interface is disabled until the WLAP Alive BPDU is received again, then the AP will reset itself. The default value is 0.
Status: mandatory Access: read-write
OBJECT-TYPE    
  INTEGER  

apTelnetEnable 1.3.6.1.4.1.388.1.5.1.2.8
Enables/Disables Telnet access to the AP. Default is enabled(1).
Status: mandatory Access: read-write
OBJECT-TYPE    
  INTEGER enabled(1), disabled(2)  

apAccCtrlEnable 1.3.6.1.4.1.388.1.5.1.2.9
Enables/Disables the Access Control function. When it is enabled, a Mobile Unit can associate with the Access Point only if its MAC address is in the Access Control Table. Default is disabled(2).
Status: mandatory Access: read-write
OBJECT-TYPE    
  INTEGER enabled(1), disabled(2)  

apTypeFilterEnable 1.3.6.1.4.1.388.1.5.1.2.10
Specifies the type of Access Point Type Filtering operation, i.e. Disabled/Forward/Discard. Default is disabled(1).
Status: mandatory Access: read-write
OBJECT-TYPE    
  INTEGER disabled(1), forward(2), discard(3)  

apWNMPEnable 1.3.6.1.4.1.388.1.5.1.2.13
Enables/Disables Use of the WNMP agent. Default is enabled(1).
Status: mandatory Access: read-write
OBJECT-TYPE    
  INTEGER enabled(1), disabled(2)  

apAPStateXchgEnable 1.3.6.1.4.1.388.1.5.1.2.14
Enables/Disables exchanging Access Point to Access Point state information by using WNMP protocol. Default is enabled(1).
Status: mandatory Access: read-write
OBJECT-TYPE    
  INTEGER enabled(1), disabled(2)  

apS24MobileIPEnable 1.3.6.1.4.1.388.1.5.1.2.15
Enables/Disables Spectrum24 Mobile IP support, i.e. AP will act as Mobility Agent. Default is disabled(2).
Status: mandatory Access: read-write
OBJECT-TYPE    
  INTEGER enabled(1), disabled(2)  

apAgentAdInterval 1.3.6.1.4.1.388.1.5.1.2.16
Interval in second at which Mobility Agent Advertise- ments are sent by the Third Party Mobility Agent(s). AP will cache the Third Party Advertisement and pass it to MU at association time. If AP does not receive the Advertisement within the interval seconds, the cached Advertisement will be deleted. If the interval is 0 or apS24MobileIPEnable is enabled, caching of the Advertisement will not occur. Range (0..1200) 3*Seconds . Default is 0.
Status: mandatory Access: read-write
OBJECT-TYPE    
  INTEGER 0..1200  

apWebServerEnable 1.3.6.1.4.1.388.1.5.1.2.17
Enables/Disables Access Point Web Server. When enabled, the Access Point will serve Web clients. Default is enabled(1)
Status: mandatory Access: read-write
OBJECT-TYPE    
  INTEGER enabled(1), disabled(2)  

apMobileHomeMD5Key 1.3.6.1.4.1.388.1.5.1.2.18
The MD5 key is a secret key shared between home agent and the mobile unit. This is used to generate a MD5 checksum, which is used for packet authentication. Length of this variable should not exceed 13 characters.
Status: mandatory Access: read-write
OBJECT-TYPE    
  DisplayString Size(1..13)  

apAdditionalGatewaysTable 1.3.6.1.4.1.388.1.5.1.2.19
A table of information for additional Gateways. The current number of entries is 7.
Status: mandatory Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    ApAdditionalGatewaysEntry

apAdditionalGatewaysEntry 1.3.6.1.4.1.388.1.5.1.2.19.1
An entry in the table of information for additional gateways for this access point. A row in this table cannot be created or deleted by SNMP operations on columns of the table.
Status: mandatory Access: not-accessible
OBJECT-TYPE    
  ApAdditionalGatewaysEntry  

additionalGatewaysIndex 1.3.6.1.4.1.388.1.5.1.2.19.1.1
Specific Gateway information Table index. Range (1..8).
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER 1..8  

apAdditionalGatewaysIPAddr 1.3.6.1.4.1.388.1.5.1.2.19.1.2
The IP address of the Gateway used for this AP.
Status: mandatory Access: read-write
OBJECT-TYPE    
  IpAddress  

apMUMUDisallowed 1.3.6.1.4.1.388.1.5.1.2.20
Controls inter-MU communication. When enabled(on), it will disallow one MU to talk to another MU through RF only.
Status: mandatory Access: read-write
OBJECT-TYPE    
  INTEGER on(1), off(2)  

apEncryptAdmin 1.3.6.1.4.1.388.1.5.1.2.21
Controls the administration of Encryption keys. This variable could only be modified thru the Serial Interface. Default is any(2).
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER serial(1), any(2)  

apSNMPMode 1.3.6.1.4.1.388.1.5.1.3.1
Specifies the mode of the SNMP Agent operation, i.e. Disabled/Readonly/ReadWrite. Default is readwrite(3).
Status: mandatory Access: read-write
OBJECT-TYPE    
  INTEGER disabled(1), readonly(2), readwrite(3)  

apROCommunityName 1.3.6.1.4.1.388.1.5.1.3.2
The Read-Only community name of the SNMP command for management station accessing this Access Point (up to 31 characters).
Status: mandatory Access: read-write
OBJECT-TYPE    
  DisplayString Size(1..31)  

apRWCommunityName 1.3.6.1.4.1.388.1.5.1.3.3
The Read-Write community name of the SNMP command for management station accessing this Access Point (up to 13 characters). This community name is same as the System Password or Telnet Password. For security purpose, if the management station uses the READ-ONLY community name to access this object, a string of 'xxxxx' will be returned.
Status: mandatory Access: read-write
OBJECT-TYPE    
  DisplayString Size(1..13)  

apTrapHost1IpAdr 1.3.6.1.4.1.388.1.5.1.3.4
Trap receiver's (i.e. Network Manager's) IP address.
Status: mandatory Access: read-write
OBJECT-TYPE    
  IpAddress  

apAllTrapsEnable 1.3.6.1.4.1.388.1.5.1.3.5
Enables/Disables all SNMP traps. Default is disabled (2).
Status: mandatory Access: read-write
OBJECT-TYPE    
  INTEGER enabled(1), disabled(2)  

apColdBootTrapEnable 1.3.6.1.4.1.388.1.5.1.3.6
Enables/Disables Access Point Cold Boot trap. Default is disabled(1). This is a generic-trap and the trap code is 0. When not disabled the trap could be directed to TrapHost1, TrapHost2 or all TrapHosts. The apAllTrapsEnable flag should be enabled for this trap to be issued.
Status: mandatory Access: read-write
OBJECT-TYPE    
  INTEGER disabled(1), trapHost1(2), trapHost2(3), all-TrapHosts(4)  

apAuthenFailureTrapEnable 1.3.6.1.4.1.388.1.5.1.3.7
Enables/Disables authentication failure trap. Default is disabled(2). This is a generic-trap and the trap code is 4. When not disabled the trap could be directed to TrapHost1, TrapHost2 or all TrapHosts. The apAllTrapsEnable flag should be enabled for this trap to be issued.
Status: mandatory Access: read-write
OBJECT-TYPE    
  INTEGER disabled(1), trapHost1(2), trapHost2(3), all-TrapHosts(4)  

apRFTrapEnable 1.3.6.1.4.1.388.1.5.1.3.8
Enables/Disables Access Point RF driver startup trap. Default is disabled(2). This is an enterprise-specific trap and the trap code is 101. When not disabled the trap could be directed to TrapHost1, TrapHost2 or all TrapHosts. The apAllTrapsEnable flag should be enabled for this trap to be issued.
Status: mandatory Access: read-write
OBJECT-TYPE    
  INTEGER disabled(1), trapHost1(2), trapHost2(3), all-TrapHosts(4)  

apACLTrapEnable 1.3.6.1.4.1.388.1.5.1.3.9
Enables/Disables Access Control violation trap. Default is disabled(2). This is an enterprise-specific trap and the trap code is 102. When not disabled the trap could be directed to TrapHost1, TrapHost2 or all TrapHosts. The apAllTrapsEnable flag should be enabled for this trap to be issued.
Status: mandatory Access: read-write
OBJECT-TYPE    
  INTEGER disabled(1), trapHost1(2), trapHost2(3), all-TrapHosts(4)  

apMUStateChngTrapEnable 1.3.6.1.4.1.388.1.5.1.3.10
Enables/Disables Mobile Unit State Change trap. Default is disabled(1). When not disabled, the following four (2) enterprise-specific traps will be generated and directed to trapHost1, TrapHost2 or all traphosts.: - MU Association Trap, the trap code is 111. - MU Un-association Trap, the trap code is 112. The enabled/disabled state of this trap depends on the state of apAllTrapsEnable.
Status: mandatory Access: read-write
OBJECT-TYPE    
  INTEGER disabled(1), trapHost1(2), trapHost2(3), all-TrapHosts(4)  

apWLAPConnChngTrapEnable 1.3.6.1.4.1.388.1.5.1.3.11
When Enabled, if there are any WLAP Connection Change, one of four (4) following enterprise-specific traps will be issued. - Root AP Up Trap, the trap code is 121. - Root AP Lost Trap, the trap code is 122. - Designated WLAP Up Trap, the trap code is 123. - Designated WLAP Lost Trap, the trap code is 124. Default is disabled(2). When not disabled the trap could be directed to TrapHost1, TrapHost2 or all TrapHosts. The apAllTrapsEnable flag should be enabled for this trap to be issued.
Status: mandatory Access: read-write
OBJECT-TYPE    
  INTEGER disabled(1), trapHost1(2), trapHost2(3), all-TrapHosts(4)  

apDHCPChangeEnable 1.3.6.1.4.1.388.1.5.1.3.12
When Enabled, if there are any DHCP network configuration change, a trap will be issued. Default is disabled(2). When not disabled the trap could be directed to TrapHost1, TrapHost2 or all TrapHosts. The apAllTrapsEnable flag should be enabled for this trap to be issued.
Status: mandatory Access: read-write
OBJECT-TYPE    
  INTEGER disabled(1), trapHost1(2), trapHost2(3), all-TrapHosts(4)  

apSNMPRequests 1.3.6.1.4.1.388.1.5.1.3.13
Indicates the number of SNMP requests to this SNMP Agent.
Status: mandatory Access: read-only
OBJECT-TYPE    
  Counter  

apSNMPTraps 1.3.6.1.4.1.388.1.5.1.3.14
Indicates the number of Traps that were generated by this SNMP Agent.
Status: mandatory Access: read-only
OBJECT-TYPE    
  Counter  

apTrapHost2IpAdr 1.3.6.1.4.1.388.1.5.1.3.15
Trap receiver's (i.e. Network Manager's) IP address.
Status: mandatory Access: read-write
OBJECT-TYPE    
  IpAddress  

apRFPortState 1.3.6.1.4.1.388.1.5.1.4.1
Specifies the state of the RF Interface. Default is up(1).
Status: mandatory Access: read-write
OBJECT-TYPE    
  INTEGER up(1), down(2)  

apNetID 1.3.6.1.4.1.388.1.5.1.4.2
The current RF Network ID for the AP. The Network name can have up to 32 alphanumerical characters.
Status: mandatory Access: read-write
OBJECT-TYPE    
  DisplayString Size(1..32)  

apCountryName 1.3.6.1.4.1.388.1.5.1.4.5
The country for which the Access Point radio is configured. It is set at the factory and may not be altered.
Status: mandatory Access: read-only
OBJECT-TYPE    
  DisplayString  

apAntennaSelect 1.3.6.1.4.1.388.1.5.1.4.6
Select either Primary antenna only (i.e. Disable antenna diversity) or both Primary and Secondary antennas (i.e. Enable antenna diversity-On). Default is diversity-On(2).
Status: mandatory Access: read-write
OBJECT-TYPE    
  INTEGER primary-only(1), diversity-On(2)  

apBCMCQMax 1.3.6.1.4.1.388.1.5.1.4.8
The maximum size of broadcast/multicast queue. Range (0..32). Default is 10.
Status: mandatory Access: read-write
OBJECT-TYPE    
  INTEGER 0..32  

apReassemblyTimeOut 1.3.6.1.4.1.388.1.5.1.4.9
Sets the time in 0.5 ms units before a timeout occurs during a packet re-assembly. Packet re-assemblies occur when a large Ethernet packet is fragmented into smaller wireless network packets. Range : 0...9999. Default is 9000.
Status: mandatory Access: read-write
OBJECT-TYPE    
  INTEGER  

apMaxRetries 1.3.6.1.4.1.388.1.5.1.4.10
The maximum number of allowed retries before aborting a single transmission. Range (0..32). Default is 15.
Status: mandatory Access: read-write
OBJECT-TYPE    
  INTEGER 0..32  

apMulticastMask 1.3.6.1.4.1.388.1.5.1.4.11
Supports broadcast download protocol for Point-of-Sale terminals that load a new operating image over the network instead of using a local non-volatile drive. The multicast mask is the top 32 bits of the MAC address and allows for a series of MAC addresses to receive multicast messages. These messages are transmitted by the AP immediately and not queued for processing at DTIM intervals.
Status: mandatory Access: read-write
OBJECT-TYPE    
  OCTET STRING Size(1..4)  

apAcceptBCESSID 1.3.6.1.4.1.388.1.5.1.4.14
Enables/Disables the function to accept Broadcast ESS ID. Enabling this feature is NOT recommended. See manual for details. Default is disabled(2).
Status: mandatory Access: read-write
OBJECT-TYPE    
  INTEGER enabled(1), disabled(2)  

apMUInactivityTimeOut 1.3.6.1.4.1.388.1.5.1.4.15
Allowable Mobile Unit inactivity time in minutes. The time out limit is from 3 to 600 minutes. Default is 60 minutes.
Status: mandatory Access: read-write
OBJECT-TYPE    
  INTEGER 3..600  

apWLAPMode 1.3.6.1.4.1.388.1.5.1.4.16
Enables/Disables Wireless AP capability and set link required option to wireless AP. Once in link-required mode, upon power-up, Root AP requires connection to the Ethernet cable and WLAP requires association with the Root AP and WLAP will keep probing forever. Default is disabled(2).
Status: mandatory Access: read-write
OBJECT-TYPE    
  INTEGER enabled(1), disabled(2), link-required(3)  

apWLAPPriority 1.3.6.1.4.1.388.1.5.1.4.17
Provides a user with the influence to determine the Root AP in wireless operation. The priority value is added as the most significant portion of the MAC address to form the WLAP ID. A WLAP with a lower numerical value for priority is more likely to become the Root AP. Priority 0xFFFF is special. It grants the WLAP with roaming capability. Default is 8000 hex from the 0 - 0xFFFF range. Reset AP for value to take effect.
Status: mandatory Access: read-write
OBJECT-TYPE    
  OCTET STRING Size(1..2)  

apWLAPManualBSSID 1.3.6.1.4.1.388.1.5.1.4.18
Specifies the BSS-ID of a particular WLAP and forces the current WLAP to associate only with that WLAP. When WLAP Manaul BSS ID is set to the current WLAP MAC address, the current WLAP jumps into Functional state immediately and waits for an Association Request from the other WLAP. Reset AP for value to take effect.
Status: mandatory Access: read-write
OBJECT-TYPE    
  PhysAddress  

apWLAPHelloTime 1.3.6.1.4.1.388.1.5.1.4.19
Sets the time lapse, in seconds, between Configuration BPDUs (Bridge Protocol Data Unit) sent to the Root AP by a designated WLAP to indicate that it is still alive. Default is 20 seconds. Reset AP for value to take effect. Range: 0..9999.
Status: mandatory Access: read-write
OBJECT-TYPE    
  INTEGER  

apWLAPMaxAge 1.3.6.1.4.1.388.1.5.1.4.20
Specifies how long, in seconds, a Configuration BPDU (Bridge Protocol Data Unit) is kept by the Root AP before it is judged too old and discarded. Consequently, the interface is considered to be disconnected. Default is 100 seconds. Recommended value is multiple of the WLAP Hello Time. Reset AP for value to take effect. Range: 0..9999.
Status: mandatory Access: read-write
OBJECT-TYPE    
  INTEGER  

apWLAPFwdDelay 1.3.6.1.4.1.388.1.5.1.4.21
Specifies how long, in seconds, an WLAP is prevented from forwarding data packets to an interface. This delay is to allow the spread of news of a topology change to all parts of a network. Default is 5 seconds. Reset AP for value to take effect. Range: 0..9999.
Status: mandatory Access: read-write
OBJECT-TYPE    
  INTEGER  

apMaxMUTrigger 1.3.6.1.4.1.388.1.5.1.4.24
Indicates the trigger point for sending apMUMaxAssocTrap trap. Range (1..255). The default value is 255.
Status: mandatory Access: read-write
OBJECT-TYPE    
  INTEGER 1..255  

apMaxRetriesVoice 1.3.6.1.4.1.388.1.5.1.4.25
The maximum number of allowed retries before aborting a single transmission. Range (0..32). Default is 5.
Status: mandatory Access: read-write
OBJECT-TYPE    
  INTEGER 0..32  

apMcastMaskVoice 1.3.6.1.4.1.388.1.5.1.4.26
This is used for Spectrum 24 telephone for intercomm function. The multicast mask is the top 32 bits of the MAC address and allows for a series of MAC addresses to receive multicast messages. These messages are transmitted by the AP immediately and not queued for processing at DTIM intervals..
Status: mandatory Access: read-write
OBJECT-TYPE    
  OCTET STRING Size(1..4)  

apWEPAlgorithm 1.3.6.1.4.1.388.1.5.1.4.30
This attribute is a set of all the shared key WEP algorithms supported by the STAs. The following are the default values and the associated algorithm. Value = 1: 128 bit Key Value = 2: 40 bit Key. IMPORTANT NOTE: The 128 bit WEP key ENcryption is currently restricted by U.S. laws. In order to activate the 128 bit Encryption, an authentic License key has to be obtained and entered through one of the interfaces such as Telnet, SNMP or Web. Upon authentication of the key the AP will enable the 128 bit ENcryption. See Access Point manual for details.
Status: mandatory Access: read-write
OBJECT-TYPE    
  INTEGER wep-128b-Key(1), wep-40b-Key(2)  

apRFRate11Mb 1.3.6.1.4.1.388.1.5.1.4.31
Specifies the Current state of the RF data rate. There are three options: - optional(1) - not-used(2) - required(3) Default is optional for 11 Mb/s data rate.
Status: mandatory Access: read-write
OBJECT-TYPE    
  INTEGER optional(1), not-used(2), required(3)  

apRFRate5-5Mb 1.3.6.1.4.1.388.1.5.1.4.32
Specifies the Current state of the RF data rate. There are three options: - optional(1) - not-used(2) - required(3) Default is optional for 5.5 Mb/S data rate.
Status: mandatory Access: read-write
OBJECT-TYPE    
  INTEGER optional(1), not-used(2), required(3)  

apRFRate2Mb 1.3.6.1.4.1.388.1.5.1.4.33
Specifies the Current state of the RF data rate. There are three options: - optional(1) - not-used(2) - required(3) Default is optional for 2 Mb/s data rate.
Status: mandatory Access: read-write
OBJECT-TYPE    
  INTEGER optional(1), not-used(2), required(3)  

apRFRate1Mb 1.3.6.1.4.1.388.1.5.1.4.34
Specifies the Current state of the RF data rate. There are three options: - optional(1) - not-used(2) - required(3) Default is required for 1 Mb/s data rate.
Status: mandatory Access: read-write
OBJECT-TYPE    
  INTEGER optional(1), not-used(2), required(3)  

apRFPreamble 1.3.6.1.4.1.388.1.5.1.4.35
This attribute is set to disabled for compatibility within the 802.11 community. Setting it to enabled shall result in performance enhancement. Default is enabled. NOTE: Only radios with version 2 hardware support RF Preamble, hence configurable to enabled state.
Status: mandatory Access: read-write
OBJECT-TYPE    
  INTEGER enabled(1), disabled(2)  

apRadioType 1.3.6.1.4.1.388.1.5.1.4.36
This attribute displays the type of radio installed in the Access Point. ds11-v1 Ver.1 Hardware short RF Preamble not supported. ds11-V2 Ver.2 Hardware Short RF Preamble supported.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER ds11-V2(1), ds11-v1(2)  

apPPPState 1.3.6.1.4.1.388.1.5.1.5.1
Indicates the current state of the PPP connection machine. Default is down(2).
Status: mandatory Access: read-write
OBJECT-TYPE    
  INTEGER up(1), down(2)  

apSerialPortUse 1.3.6.1.4.1.388.1.5.1.5.2
Specifies whether the Serial Interface is to be used as User Interface(UI) or PPP. Default is ui(2).
Status: mandatory Access: read-write
OBJECT-TYPE    
  INTEGER ppp(1), ui(2)  

apModemConnected 1.3.6.1.4.1.388.1.5.1.5.3
Specifies whether the Serial Interface has a modem attached to it. Default is no(2).
Status: mandatory Access: read-write
OBJECT-TYPE    
  INTEGER yes(1), no(2)  

apConnectMode 1.3.6.1.4.1.388.1.5.1.5.4
Specifies the Modem connection mode: - originate(1): AP sends dial-out information. - answer(2): AP waits for dial-in information. Default is answer(2).
Status: mandatory Access: read-write
OBJECT-TYPE    
  INTEGER originate(1), answer(2)  

apDialOutNumber 1.3.6.1.4.1.388.1.5.1.5.5
Specifies the number to be dialed by the modem.
Status: mandatory Access: read-write
OBJECT-TYPE    
  DisplayString Size(1..32)  

apDialOutMode 1.3.6.1.4.1.388.1.5.1.5.6
Specifies the dialout mode: - auto(1): Modem dial out during startup time. - manual(2): Modem dial out by manned intervention Default is auto(1).
Status: mandatory Access: read-write
OBJECT-TYPE    
  INTEGER auto(1), manual(2)  

apAnswerWaitTime 1.3.6.1.4.1.388.1.5.1.5.7
Specifies the period (in seconds) the AP will wait for the remote unit to answer the call. Default is 60 seconds.
Status: mandatory Access: read-write
OBJECT-TYPE    
  INTEGER  

apModemSpeaker 1.3.6.1.4.1.388.1.5.1.5.8
Specifies if modem speaker is turned on(1) or off(2). Default is on(1).
Status: mandatory Access: read-write
OBJECT-TYPE    
  INTEGER on(1), off(2)  

apInactivityTimeout 1.3.6.1.4.1.388.1.5.1.5.9
Specifies the User Interface inactivity timeout in minutes. 0 means no timeout. Default is 5 minutes.
Status: mandatory Access: read-write
OBJECT-TYPE    
  INTEGER  

apPPPTimeout 1.3.6.1.4.1.388.1.5.1.5.10
Specifies the PPP event timeout in seconds. Default is 3 seconds.
Status: mandatory Access: read-write
OBJECT-TYPE    
  INTEGER  

apPPPTerminates 1.3.6.1.4.1.388.1.5.1.5.11
Specifies the maximum number of PPP terminate requests. Default is 10.
Status: mandatory Access: read-write
OBJECT-TYPE    
  Counter  

apAddrFilterTable 1.3.6.1.4.1.388.1.5.1.6
A table of MAC addresses not allowed to associate with the Access Point. The maximum number of entries in the table is 512.
Status: mandatory Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    ApAddrFilterEntry

apAddrFilterEntry 1.3.6.1.4.1.388.1.5.1.6.1
An entry in the table of Address Filter. A row in this table is created by setting the value of disallowedMU to the MAC address of the MU not allowed to associate with the Access Point. A row in this table is deleted by setting the value of disallowedMU to '000000000000'.
Status: mandatory Access: not-accessible
OBJECT-TYPE    
  ApAddrFilterEntry  

disallowedIndex 1.3.6.1.4.1.388.1.5.1.6.1.1
Address Filter Table index. Range (1..512).
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER 1..512  

disallowedMU 1.3.6.1.4.1.388.1.5.1.6.1.2
MU MAC address which is not allowed to be associated with this Access Point.
Status: mandatory Access: read-write
OBJECT-TYPE    
  PhysAddress  

apTypeFilterTable 1.3.6.1.4.1.388.1.5.1.7
A table of Ethernet types (i.e. 16-bit DIX Ethernet type), which are entered by the user and supported for the type filtering function. The maximum number of entries in the table is 16.
Status: mandatory Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    ApTypeFilterEntry

apTypeFilterEntry 1.3.6.1.4.1.388.1.5.1.7.1
An entry in the table of Type Filter. A row in this table is created by setting the value of etherType to Ethernet packet type in hexadecimal. A row in this table is deleted by setting the value of etherType to 00
Status: mandatory Access: not-accessible
OBJECT-TYPE    
  ApTypeFilterEntry  

typeIndex 1.3.6.1.4.1.388.1.5.1.7.1.1
Filter Type Table index. Range (1..16).
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER 1..16  

etherType 1.3.6.1.4.1.388.1.5.1.7.1.2
A 16-bit Ethernet Protocol Type in hexadecimal. Range of valid Entries: 0X05DD .. 0XFFFE
Status: mandatory Access: read-write
OBJECT-TYPE    
  OCTET STRING Size(1..2)  

ap128bWEPKeyTable 1.3.6.1.4.1.388.1.5.1.8
A table of default WEP Keys The maximum number of entries in the table is 4.
Status: mandatory Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    ApWEPKeyEntry

apWEPKeyEntry 1.3.6.1.4.1.388.1.5.1.8.1
An entry in the table of Default WEP Keys.
Status: mandatory Access: not-accessible
OBJECT-TYPE    
  ApWEPKeyEntry  

ap128bWepkeyIndex 1.3.6.1.4.1.388.1.5.1.8.1.1
WEP Key Table index. Range (1..4).
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER 1..4  

ap128bWepKeyValue 1.3.6.1.4.1.388.1.5.1.8.1.2
A Default WEP Key Value. This value should be 26 character long. IMPORTANT NOTE: The 128 bit WEP key Encryption is currently restricted by U.S. laws. Its use is restricted to AP's manufactured for U.S. only. In order to activate the 128 bit Encryption for all other countries, an access code has to be obtained and entered through one of the interfaces such as Serial, Telnet, SNMP or Web. Upon authentication of the key the AP will enable the 128 bit Encryption. See Access Point manual for details.
Status: mandatory Access: read-write
OBJECT-TYPE    
  WEPKeytype128b  

apTrafficMatrixTable 1.3.6.1.4.1.388.1.5.2.1
A table of Access Point Traffic Matrix which provides information on packets transmitted from one interface to another (Ethernet, PPP, radio, AP). The table also displays the number of broadcast packets transmitted from the Access Point. The current number of entries is 5.
Status: mandatory Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    ApTrafficMatrixEntry

apTrafficMatrixEntry 1.3.6.1.4.1.388.1.5.2.1.1
An entry in the table of Access Point Traffic Matrix. A row in this table cannot be created or deleted by SNMP operations on columns of the table.
Status: mandatory Access: not-accessible
OBJECT-TYPE    
  ApTrafficMatrixEntry  

apTMTableIndex 1.3.6.1.4.1.388.1.5.2.1.1.1
Access Point Traffic Matrix Table index. Range (1..5).
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER 1..5  

apProtoItfName 1.3.6.1.4.1.388.1.5.2.1.1.2
Access Point Protocol Interface Name (i.e. Ethernet, PPP, Radio, AP).
Status: mandatory Access: read-only
OBJECT-TYPE    
  DisplayString Size(1..12)  

apNPktsToEnets 1.3.6.1.4.1.388.1.5.2.1.1.3
Indicates the number of packets sent from the Access Point Protocol Interface to the Ethernet Interface. This field should always be zero if the Access Point Protocol Interface is Ethernet.
Status: mandatory Access: read-only
OBJECT-TYPE    
  Counter  

apNPktsToPpps 1.3.6.1.4.1.388.1.5.2.1.1.4
Indicates the number of packets sent from the Access Point Protocol Interface to the PPP Interface. This field is meaningful only if the PPP interface is enabled.
Status: mandatory Access: read-only
OBJECT-TYPE    
  Counter  

apNPktsToRfs 1.3.6.1.4.1.388.1.5.2.1.1.5
Indicates the number of packets sent from the Access Point Protocol Interface to the RF Interface. If the Access Point Protocol Interface is RF, these are frames from one MU to another.
Status: mandatory Access: read-only
OBJECT-TYPE    
  Counter  

apNPktsToAPStks 1.3.6.1.4.1.388.1.5.2.1.1.6
Indicates the number of packets sent from the Access Point Protocol Interface to the internal Access Point stack. This field should always be zero if the Access Point Protocol Interface is Access Point Stack.
Status: mandatory Access: read-only
OBJECT-TYPE    
  Counter  

apItfStatTable 1.3.6.1.4.1.388.1.5.2.2
A table of Access Point Interfaces Statistics, which provides packets forwarding statistics for each inter- face (Ethernet, PPP, RF, AP stack). Interface statistics also provide performance informa- tion for each interface in Packets-per-second (PPS) and Bytes- per-second (BPS). The AP interface indicates packets sent to the AP stack (e.g. configuration requests, SNMP, Telnet etc.). The current number of entries is 4.
Status: mandatory Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    ApItfStatEntry

apItfStatEntry 1.3.6.1.4.1.388.1.5.2.2.1
An entry in the table of Access Point Interface Statistics. A row in this table cannot be created or deleted by SNMP operations on columns of the table.
Status: mandatory Access: not-accessible
OBJECT-TYPE    
  ApItfStatEntry  

apItfStatIndex 1.3.6.1.4.1.388.1.5.2.2.1.1
Access Point Interface Statistics Table index. Range (1..4).
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER 1..4  

apInterfaceName 1.3.6.1.4.1.388.1.5.2.2.1.2
Access Point Interface Name (Ethernet, PPP, RF, AP).
Status: mandatory Access: read-only
OBJECT-TYPE    
  DisplayString Size(1..12)  

apPacketsIns 1.3.6.1.4.1.388.1.5.2.2.1.3
Indicates the number of good packets received on the specified interface.
Status: mandatory Access: read-only
OBJECT-TYPE    
  Counter  

apPacketsOuts 1.3.6.1.4.1.388.1.5.2.2.1.4
Indicates the number of packets successfully transmitted on the specified interface.
Status: mandatory Access: read-only
OBJECT-TYPE    
  Counter  

apOctetsIns 1.3.6.1.4.1.388.1.5.2.2.1.5
Indicates the number of good bytes received on the specified interface.
Status: mandatory Access: read-only
OBJECT-TYPE    
  Counter  

apOctetsOuts 1.3.6.1.4.1.388.1.5.2.2.1.6
Indicates the number of bytes successfully transmitted on the specified interface.
Status: mandatory Access: read-only
OBJECT-TYPE    
  Counter  

apPktsInPerSec 1.3.6.1.4.1.388.1.5.2.2.1.7
Indicates the number of good packets per second received on the specified Interface.
Status: mandatory Access: read-only
OBJECT-TYPE    
  Gauge  

apPktsOutPerSec 1.3.6.1.4.1.388.1.5.2.2.1.8
Indicates the number of packets per second successfully transmitted on the specified interface.
Status: mandatory Access: read-only
OBJECT-TYPE    
  Gauge  

apOctInPerSec 1.3.6.1.4.1.388.1.5.2.2.1.9
Indicates the number of good bytes per second received on the specified Interface.
Status: mandatory Access: read-only
OBJECT-TYPE    
  Gauge  

apOctOutPerSec 1.3.6.1.4.1.388.1.5.2.2.1.10
Indicates the number of bytes per second successfully transmitted on the specified interface.
Status: mandatory Access: read-only
OBJECT-TYPE    
  Gauge  

apEPktsSeens 1.3.6.1.4.1.388.1.5.2.3.1
Indicates the number of packets that have been seen on the Ethernet interface. Most of these packets are for stations other than those associated with this AP.
Status: mandatory Access: read-only
OBJECT-TYPE    
  Counter  

apEPktsForwardeds 1.3.6.1.4.1.388.1.5.2.3.2
Indicates the number of Ethernet packets forwarded from the Ethernet interface to other interfaces.
Status: mandatory Access: read-only
OBJECT-TYPE    
  Counter  

apEPktsDiscNoMatchs 1.3.6.1.4.1.388.1.5.2.3.3
Indicates the number of packets discarded due to unknown destination (i.e. no database entry).
Status: mandatory Access: read-only
OBJECT-TYPE    
  Counter  

apEPktsDiscForceds 1.3.6.1.4.1.388.1.5.2.3.4
Indicates the number of packets discarded due to Type or Address filters applied.
Status: mandatory Access: read-only
OBJECT-TYPE    
  Counter  

apEPktsDiscBuffers 1.3.6.1.4.1.388.1.5.2.3.5
Indicates the number of packets discarded due to lack of available buffers in AP.
Status: mandatory Access: read-only
OBJECT-TYPE    
  Counter  

apEPktsDiscCRCs 1.3.6.1.4.1.388.1.5.2.3.6
Indicates the number of packets discarded due to CRC errors.
Status: mandatory Access: read-only
OBJECT-TYPE    
  Counter  

apEPktsSents 1.3.6.1.4.1.388.1.5.2.3.7
Indicates the number of packets sent by this Ethernet Port.
Status: mandatory Access: read-only
OBJECT-TYPE    
  Counter  

apEAnyCollisions 1.3.6.1.4.1.388.1.5.2.3.8
Indicates the number of packets that suffer at least one collision.
Status: mandatory Access: read-only
OBJECT-TYPE    
  Counter  

apE1orMoreColls 1.3.6.1.4.1.388.1.5.2.3.9
Indicates the number of packets that suffer more than one collision.
Status: mandatory Access: read-only
OBJECT-TYPE    
  Counter  

apEMaxCollisions 1.3.6.1.4.1.388.1.5.2.3.10
Indicates the number of packets that suffer more than the maximum number of collisions.
Status: mandatory Access: read-only
OBJECT-TYPE    
  Counter  

apELateCollisions 1.3.6.1.4.1.388.1.5.2.3.11
Indicates the number of packets that suffer late collisions.
Status: mandatory Access: read-only
OBJECT-TYPE    
  Counter  

apEPktsDefers 1.3.6.1.4.1.388.1.5.2.3.12
Indicates the times AP had to defer transmit requests on Ethernet due to busy medium.
Status: mandatory Access: read-only
OBJECT-TYPE    
  Counter  

apEBcMcPkts 1.3.6.1.4.1.388.1.5.2.3.13
Indicates the number of broadcast/multicast packets that have been transmitted.
Status: mandatory Access: read-only
OBJECT-TYPE    
  Counter  

apEIndividualAddrs 1.3.6.1.4.1.388.1.5.2.3.14
Indicates the number of individual address (unicast) packets that have been received.
Status: mandatory Access: read-only
OBJECT-TYPE    
  Counter  

rfBcMcPktsSents 1.3.6.1.4.1.388.1.5.2.4.1
Indicates the number of broadcast/multicast packets that have been successfully transmitted.
Status: mandatory Access: read-only
OBJECT-TYPE    
  Counter  

rfBcMcPktsRcvds 1.3.6.1.4.1.388.1.5.2.4.2
Indicates the number of broadcast/multicast packets that have been successfully received.
Status: mandatory Access: read-only
OBJECT-TYPE    
  Counter  

rfBcMcOctSents 1.3.6.1.4.1.388.1.5.2.4.3
Indicates the number of broadcast/multicast bytes that have been successfully transmitted.
Status: mandatory Access: read-only
OBJECT-TYPE    
  Counter  

rfBcMcOctRcvds 1.3.6.1.4.1.388.1.5.2.4.4
Indicates the number of broadcast/multicast bytes that have been successfully received.
Status: mandatory Access: read-only
OBJECT-TYPE    
  Counter  

rfSysPktsSents 1.3.6.1.4.1.388.1.5.2.4.5
Indicates the number of system packets (includes probe operations packets) that have been successfully transmitted.
Status: mandatory Access: read-only
OBJECT-TYPE    
  Counter  

rfSysPktsRcvds 1.3.6.1.4.1.388.1.5.2.4.6
Indicates the number of system packets (includes probes /associate packets) that have been successfully received.
Status: mandatory Access: read-only
OBJECT-TYPE    
  Counter  

rfSBcMcPktsSents 1.3.6.1.4.1.388.1.5.2.4.7
Indicates the number of system broadcast/multicast packets (includes beacons) that have been successfully transmitted.
Status: mandatory Access: read-only
OBJECT-TYPE    
  Counter  

rfSBcMcPktsRcvds 1.3.6.1.4.1.388.1.5.2.4.8
Indicates the number of system broadcast/multicast (includes beacons) packets that have been successfully received.
Status: mandatory Access: read-only
OBJECT-TYPE    
  Counter  

rfSuccFragPkts 1.3.6.1.4.1.388.1.5.2.4.9
Indicates the number of packets that were fragmented and for which all fragments were acked.
Status: mandatory Access: read-only
OBJECT-TYPE    
  Counter  

rfUnsuccFragPkts 1.3.6.1.4.1.388.1.5.2.4.10
Indicates the number of packets that were fragmented but for which one or more fragments were not acked.
Status: mandatory Access: read-only
OBJECT-TYPE    
  Counter  

rfTotalFragSents 1.3.6.1.4.1.388.1.5.2.4.11
Indicates the number of packets fragments that have been sent.
Status: mandatory Access: read-only
OBJECT-TYPE    
  Counter  

rfTotalFragRcvds 1.3.6.1.4.1.388.1.5.2.4.12
Indicates the number of packets fragments that have been received.
Status: mandatory Access: read-only
OBJECT-TYPE    
  Counter  

rfSuccReassPkts 1.3.6.1.4.1.388.1.5.2.4.13
Indicates the number of packets that were reassigned and successfully reassembled.
Status: mandatory Access: read-only
OBJECT-TYPE    
  Counter  

rfUnsuccReassPkts 1.3.6.1.4.1.388.1.5.2.4.14
Indicates the number of packets that were unsuccessfully reassembled.
Status: mandatory Access: read-only
OBJECT-TYPE    
  Counter  

rfAssocMUs 1.3.6.1.4.1.388.1.5.2.4.15
Indicates the number of MUs currently associated with this AP.
Status: mandatory Access: read-only
OBJECT-TYPE    
  Counter  

rfRcvdCRCErrors 1.3.6.1.4.1.388.1.5.2.4.16
Indicates the number of packets that were received but had the CRC errors.
Status: mandatory Access: read-only
OBJECT-TYPE    
  Counter  

rfRcvdDupPkts 1.3.6.1.4.1.388.1.5.2.4.17
Indicates the number of packets that were received but were duplicates of previously received. This is usually an indication that an ACK was not received by the sending unit.
Status: mandatory Access: read-only
OBJECT-TYPE    
  Counter  

rfTotalCollisions 1.3.6.1.4.1.388.1.5.2.4.18
Indicates the number of collisions that have occured on the interface. A collision on the RF interface means that an ack was not received or that a RTS was not answered by a CTS.
Status: mandatory Access: read-only
OBJECT-TYPE    
  Counter  

rfPktsWithoutColls 1.3.6.1.4.1.388.1.5.2.4.19
Indicates the number of packets without any collision.
Status: mandatory Access: read-only
OBJECT-TYPE    
  Counter  

rfPktsWithMaxColls 1.3.6.1.4.1.388.1.5.2.4.20
Indicates the number of packets that suffered the maximum number of collisions.
Status: mandatory Access: read-only
OBJECT-TYPE    
  Counter  

rfPktsWithColls 1.3.6.1.4.1.388.1.5.2.4.21
Indicates the number of packets that suffered at least one collision.
Status: mandatory Access: read-only
OBJECT-TYPE    
  Counter  

rfDataPktsSents 1.3.6.1.4.1.388.1.5.2.4.22
Indicates the number of packets transmitted.
Status: mandatory Access: read-only
OBJECT-TYPE    
  Counter  

rfDataPktsRcvds 1.3.6.1.4.1.388.1.5.2.4.23
Indicates the number of packets that were successfully received.
Status: mandatory Access: read-only
OBJECT-TYPE    
  Counter  

rfDataOctetsSents 1.3.6.1.4.1.388.1.5.2.4.24
Indicates the number of octets transmitted.
Status: mandatory Access: read-only
OBJECT-TYPE    
  Counter  

rfDataOctetsRcvds 1.3.6.1.4.1.388.1.5.2.4.25
Indicates the number of octets that were successfully received.
Status: mandatory Access: read-only
OBJECT-TYPE    
  Counter  

rfEncrypPktsSents 1.3.6.1.4.1.388.1.5.2.4.26
Indicates the number of Encrypted packets transmitted.
Status: mandatory Access: read-only
OBJECT-TYPE    
  Counter  

rfEncrypPktsRcvds 1.3.6.1.4.1.388.1.5.2.4.27
Indicates the number of Encrypted packets that were successfully received.
Status: mandatory Access: read-only
OBJECT-TYPE    
  Counter  

apNbrOfDialouts 1.3.6.1.4.1.388.1.5.2.6.1
Indicates the number of dialout attempts by the AP.
Status: mandatory Access: read-only
OBJECT-TYPE    
  Counter  

apDialoutFailures 1.3.6.1.4.1.388.1.5.2.6.2
Indicates the number of dialout failures by the AP.
Status: mandatory Access: read-only
OBJECT-TYPE    
  Counter  

apNbrOfAnswers 1.3.6.1.4.1.388.1.5.2.6.3
Indicates the number of answer attempts by the AP.
Status: mandatory Access: read-only
OBJECT-TYPE    
  Counter  

apCurrCallTime 1.3.6.1.4.1.388.1.5.2.6.4
Indicates the length in seconds of current connection session. Note: the time is relative to the boot time of this AP.
Status: mandatory Access: read-only
OBJECT-TYPE    
  TimeTicks  

apLastCallTime 1.3.6.1.4.1.388.1.5.2.6.5
Indicates the length in seconds of last connection session. Note: the time is relative to the boot time of this AP.
Status: mandatory Access: read-only
OBJECT-TYPE    
  TimeTicks  

apWNMPCfgPkts 1.3.6.1.4.1.388.1.5.2.7.1
Indicates the number of WNMP configuration requests received from NetVision.
Status: mandatory Access: read-only
OBJECT-TYPE    
  Counter  

wEchoRequests 1.3.6.1.4.1.388.1.5.2.7.2
Indicates the number of WNMP Echo Requests received by this AP.
Status: mandatory Access: read-only
OBJECT-TYPE    
  Counter  

wPingRequests 1.3.6.1.4.1.388.1.5.2.7.3
Indicates the number of WNMP ping requests received by this AP.
Status: mandatory Access: read-only
OBJECT-TYPE    
  Counter  

wPktsFromNVs 1.3.6.1.4.1.388.1.5.2.7.4
Indicates the number of WNMP packets that were received from NetVision via this AP.
Status: mandatory Access: read-only
OBJECT-TYPE    
  Counter  

wPPktsToNVs 1.3.6.1.4.1.388.1.5.2.7.5
Indicates the number of WNMP packets that were sent to the NetVision via this AP.
Status: mandatory Access: read-only
OBJECT-TYPE    
  Counter  

wPassThruEchoes 1.3.6.1.4.1.388.1.5.2.7.6
Indicates the number of WNMP packets for other stations that passed through this AP.
Status: mandatory Access: read-only
OBJECT-TYPE    
  Counter  

apCurrentMUs 1.3.6.1.4.1.388.1.5.2.8.1
Indicates the number of MUs currently associated with this AP.
Status: mandatory Access: read-only
OBJECT-TYPE    
  Counter  

apMaxMUs 1.3.6.1.4.1.388.1.5.2.8.2
Indicates the highest number of MUs ever associated with this AP.
Status: mandatory Access: read-only
OBJECT-TYPE    
  Counter  

apTotalAssocs 1.3.6.1.4.1.388.1.5.2.8.3
Indicates the total number of associations by all MUs with this AP.
Status: mandatory Access: read-only
OBJECT-TYPE    
  Counter  

apMUTable 1.3.6.1.4.1.388.1.5.2.8.4
A table of information for a specific MU associated with this Access Point. The current number of entries is 127.
Status: mandatory Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    ApMUEntry

apMUEntry 1.3.6.1.4.1.388.1.5.2.8.4.1
An entry in the table of information for a specific MU associated with this Access Point. A row in this table cannot be created or deleted by SNMP operations on columns of the table.
Status: mandatory Access: not-accessible
OBJECT-TYPE    
  ApMUEntry  

muIndex 1.3.6.1.4.1.388.1.5.2.8.4.1.1
Specific MU information Table index. Range (1..127).
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER 1..127  

muMacAddr 1.3.6.1.4.1.388.1.5.2.8.4.1.2
The MAC address of the MU associated with this AP.
Status: mandatory Access: read-only
OBJECT-TYPE    
  PhysAddress  

muInterface 1.3.6.1.4.1.388.1.5.2.8.4.1.3
Indicates the interface on which this MU is located. Note: The AP may learn of an MU via the RF network or from the wired networks such as Ethernet or PPP. In this release, the AP does not keep track of those MUs reachable via the Ethernet, but that will change in future releases.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER ethernet(1), ppp(2), rf(3), apstack(4)  

muState 1.3.6.1.4.1.388.1.5.2.8.4.1.4
Indicates the state of this MU.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER associated(3), not-associated(4)  

muPowerMode 1.3.6.1.4.1.388.1.5.2.8.4.1.5
Indicates the MU power mode (Power Save Protocol mode or Continue Active Mode.)
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER cam(1), psp(2)  

muStationID 1.3.6.1.4.1.388.1.5.2.8.4.1.6
Indicates the MU station ID.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER  

muLastAPAddr 1.3.6.1.4.1.388.1.5.2.8.4.1.7
Indicates the MAC address of the last AP with which this MU had an association.
Status: mandatory Access: read-only
OBJECT-TYPE    
  PhysAddress  

muTotalAssoc 1.3.6.1.4.1.388.1.5.2.8.4.1.8
Indicates the total associations for this MU.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER  

muAssocStart 1.3.6.1.4.1.388.1.5.2.8.4.1.9
Indicates when the MU began its current association with this AP. Note: Time is represented in seconds and the time is relative to the boot time of this AP. This is also true for all the association objects listed below.
Status: mandatory Access: read-only
OBJECT-TYPE    
  TimeTicks  

muLstAssStrt 1.3.6.1.4.1.388.1.5.2.8.4.1.10
Indicates when the MU began its prior association with this AP. If this is the first association with this AP, this value is zero.
Status: mandatory Access: read-only
OBJECT-TYPE    
  TimeTicks  

muLastAssEnd 1.3.6.1.4.1.388.1.5.2.8.4.1.11
Indicates when the MU ended its previous association with this AP. If this is the first association with this AP, this value is zero.
Status: mandatory Access: read-only
OBJECT-TYPE    
  TimeTicks  

muNPktsSents 1.3.6.1.4.1.388.1.5.2.8.4.1.12
Indicates the number of packets successfully transmitted to this MU.
Status: mandatory Access: read-only
OBJECT-TYPE    
  Counter  

muNPktsRcvds 1.3.6.1.4.1.388.1.5.2.8.4.1.13
Indicates the number of Good Packets received from this MU.
Status: mandatory Access: read-only
OBJECT-TYPE    
  Counter  

muNBytesSents 1.3.6.1.4.1.388.1.5.2.8.4.1.14
Indicates the number of bytes successfully transmitted to this MU.
Status: mandatory Access: read-only
OBJECT-TYPE    
  Counter  

muNBytesRcvds 1.3.6.1.4.1.388.1.5.2.8.4.1.15
Indicates the number of Good Bytes received from this MU.
Status: mandatory Access: read-only
OBJECT-TYPE    
  Counter  

muNDiscdPkts 1.3.6.1.4.1.388.1.5.2.8.4.1.16
Indicates the number of received packets discarded because no buffers.
Status: mandatory Access: read-only
OBJECT-TYPE    
  Counter  

muTmLastData 1.3.6.1.4.1.388.1.5.2.8.4.1.17
Indicates the time when the last good packet was received from this MU. The packet may be either an ACK, Data, or Poll.
Status: mandatory Access: read-only
OBJECT-TYPE    
  TimeTicks  

muPriority 1.3.6.1.4.1.388.1.5.2.8.4.1.18
Indicates the Voice/Data priority mode for this MU.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER voice(1), normal(2)  

muSupportedRates 1.3.6.1.4.1.388.1.5.2.8.4.1.19
Indicates the supported data rates for this MU. The unit is MB/second.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER one-Mb(1), two-Mb(2), one-and-two-Mb(3), five-half-Mb(4), one-and-five-half-Mb(5), two-and-five-half-Mb(6), one-and-two-and-five-half-Mb(7), eleven-Mb(8), one-and-eleven-Mb(9), two-and-eleven-Mb(10), one-and-two-and-eleven-Mb(11), five-half-and-eleven-Mb(12), one-and-five-half-and-eleven-Mb(13), two-and-five-half-and-eleven-Mb(14), one-and-two-and-five-half-and-eleven-Mb(15)  

muCurrentXmtRate 1.3.6.1.4.1.388.1.5.2.8.4.1.20
Indicates the current transmit data rate for this MU. The unit is MB/second.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER one-Megabit(1), two-Megabit(2), five-half-Megabit(3), eleven-Megabit(4)  

muLastActivity 1.3.6.1.4.1.388.1.5.2.8.4.1.21
Indicates the time for the last activity for this MU.
Status: mandatory Access: read-only
OBJECT-TYPE    
  TimeTicks  

apMUHmAgTable 1.3.6.1.4.1.388.1.5.2.8.5
A table of information on Mobile IP Home agent. The current number of entries is 127.
Status: mandatory Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    ApMUHATEntry

apMUHATEntry 1.3.6.1.4.1.388.1.5.2.8.5.1
An entry in the table of information on on Mobile IP Home agent. A row in this table cannot be created or deleted by SNMP operations on columns of the table.
Status: mandatory Access: not-accessible
OBJECT-TYPE    
  ApMUHATEntry  

muHATMUIpAddr 1.3.6.1.4.1.388.1.5.2.8.5.1.1
This is the IP Address of the MU visiting in the foreign network.
Status: mandatory Access: read-only
OBJECT-TYPE    
  IpAddress  

muHATFrAgIpAddr 1.3.6.1.4.1.388.1.5.2.8.5.1.2
This is the IP Address of the Foreign agent for the visiting MU.
Status: mandatory Access: read-only
OBJECT-TYPE    
  IpAddress  

apMUFrAgTable 1.3.6.1.4.1.388.1.5.2.8.6
A table of information on Mobile IP Foreign agent. The current number of entries is 127.
Status: mandatory Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    ApMUFATEntry

apMUFATEntry 1.3.6.1.4.1.388.1.5.2.8.6.1
An entry in the table of information on Mobile IP Foreign agent. A row in this table cannot be created or deleted by SNMP operations on columns of the table.
Status: mandatory Access: not-accessible
OBJECT-TYPE    
  ApMUFATEntry  

muFATMUIpAddr 1.3.6.1.4.1.388.1.5.2.8.6.1.1
This is the IP Address of the MU visiting in the foreign network.
Status: mandatory Access: read-only
OBJECT-TYPE    
  IpAddress  

muFATHmAgIpAddr 1.3.6.1.4.1.388.1.5.2.8.6.1.2
This is the IP Address of the home agent for the visiting MU.
Status: mandatory Access: read-only
OBJECT-TYPE    
  IpAddress  

apKnownAPsTable 1.3.6.1.4.1.388.1.5.2.9
A table of information on other Access Points known by this Access Point. The current number of entries is 32.
Status: mandatory Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    ApKnownAPsEntry

apKnownAPsEntry 1.3.6.1.4.1.388.1.5.2.9.1
An entry in the table of information on the Known Access Points. A row in this table cannot be created or deleted by SNMP operations on columns of the table.
Status: mandatory Access: not-accessible
OBJECT-TYPE    
  ApKnownAPsEntry  

apAPMacAddr 1.3.6.1.4.1.388.1.5.2.9.1.1
Mac Address of this Known AP.
Status: mandatory Access: read-only
OBJECT-TYPE    
  PhysAddress  

apAPIpAddr 1.3.6.1.4.1.388.1.5.2.9.1.2
IP Address of this Known AP.
Status: mandatory Access: read-only
OBJECT-TYPE    
  IpAddress  

apHoppingSet 1.3.6.1.4.1.388.1.5.2.9.1.3
Hopping Set of this Known AP.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER  

apHoppingSeq 1.3.6.1.4.1.388.1.5.2.9.1.4
Hopping Sequence of this Known AP.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER  

apNbrOfMUs 1.3.6.1.4.1.388.1.5.2.9.1.5
Indicates the number of MUs currently associated with this known AP.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER  

apKBIOS 1.3.6.1.4.1.388.1.5.2.9.1.6
Kilobytes sent and received per second by this known AP on the radio interface.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER  

apAway 1.3.6.1.4.1.388.1.5.2.9.1.7
Indicate that whether this known AP is still alive or not. If the current AP does not receive WNMP packet from this known AP within 36 seconds, this known AP is considered 'AWAY'.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER yes(1), no(2)  

ap802dot11Protocol 1.3.6.1.4.1.388.1.5.2.9.1.8
Indicate that whether this known AP is 802.11 compliant.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER yes(1), no(2)  

apFwVer 1.3.6.1.4.1.388.1.5.2.9.1.9
Indicates The firmware revision for this known Access Point.
Status: mandatory Access: read-only
OBJECT-TYPE    
  DisplayString Size(1..16)  

apDSchannel 1.3.6.1.4.1.388.1.5.2.9.1.10
The current operating frequency channel of the DSSS PHY. Valid channel numbers are as defined in IEEE 802.11 specification section 15.4.6.2.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER  

apAdrViolations 1.3.6.1.4.1.388.1.5.2.10.1
Indicates the number of Mobile Unit MAC address violations counted.
Status: mandatory Access: read-only
OBJECT-TYPE    
  Counter  

apTypeViolations 1.3.6.1.4.1.388.1.5.2.10.2
Indicates the number of Ethernet packet type violations counted.
Status: mandatory Access: read-only
OBJECT-TYPE    
  Counter  

apNbrOfWLAPItfs 1.3.6.1.4.1.388.1.5.2.11.1
Indicates number of WLAP interfaces established.
Status: mandatory Access: read-only
OBJECT-TYPE    
  Counter  

apWLAPState 1.3.6.1.4.1.388.1.5.2.11.2
Indicates the current WLAP state. The state values and meanings are as follows: - During power-up initialization: Initializing(1) - During WLAP association process: send-probe(2) send-assoc-req(3) send-cfg-bpdu(4) wait-for-probe(5) send-probe-rsp(6) send-assoc-rsp(7) send-cfg-rsp(8) receive-root-rsp(10) - During WLAP operation: root-ap-lost(12) disabled(14) functional(15) wlap-lost-on-ethernet(16)
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER initializing(1), send-probe(2), send-assoc-req(3), send-cfg-bpdu(4), wait-for-probe(5), send-probe-rsp(6), send-assoc-rsp(7), send-cfg-rsp(8), receive-root-rsp(10), root-ap-lost(12), disabled(14), functional(15), wlap-lost-on-ethernet(16)  

apWLAPHopSequence 1.3.6.1.4.1.388.1.5.2.11.3
Indicates the hop sequence of the Root AP followed by this WLAP.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER  

apRootInterface 1.3.6.1.4.1.388.1.5.2.11.4
Indicates the WLAP interface leading to the Root AP.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER  

apRootWLAPID 1.3.6.1.4.1.388.1.5.2.11.5
Indicates the WLAP ID of the Root AP. It consists of 2 bytes of priority (Default is 0x8000) and 6 bytes of MAC address of the Root AP
Status: mandatory Access: read-only
OBJECT-TYPE    
  OCTET STRING Size(1..8)  

apRootPathCost 1.3.6.1.4.1.388.1.5.2.11.6
Indicates how many hops away the current WLAP is from the Root AP.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER  

apWLAPID 1.3.6.1.4.1.388.1.5.2.11.7
Indicates the WLAP ID of the current WLAP. It consists of 2 bytes of priority (Default is 0x8000) and 6 bytes MAC address of the current WLAP
Status: mandatory Access: read-only
OBJECT-TYPE    
  OCTET STRING Size(1..8)  

apWLAPItfTable 1.3.6.1.4.1.388.1.5.2.11.8
A table of wireless AP interfaces information, which contains four (4) AP-to-AP interfaces.
Status: mandatory Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    ApWLAPItfEntry

apWLAPItfEntry 1.3.6.1.4.1.388.1.5.2.11.8.1
An entry in the table of wireless AP interfaces information.
Status: mandatory Access: not-accessible
OBJECT-TYPE    
  ApWLAPItfEntry  

apWLAPItfID 1.3.6.1.4.1.388.1.5.2.11.8.1.1
WLAP interface ID. It consists of 1 byte of priority (Default is 0x80) and 1 byte of interface ID.
Status: mandatory Access: read-only
OBJECT-TYPE    
  OCTET STRING Size(1..2)  

apWLAPItfAddr 1.3.6.1.4.1.388.1.5.2.11.8.1.2
The MAC address of the associated WLAP on this interface.
Status: mandatory Access: read-only
OBJECT-TYPE    
  PhysAddress  

apWLAPItfState 1.3.6.1.4.1.388.1.5.2.11.8.1.3
The current state of the Wireless AP interface, ie : Disabled(1), Listening(2), Learning(3), Forwarding(4), or Blocking(5).
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER disabled(1), listening(2), learning(3), forwarding(4), blocking(5)  

apWLAPPathCost 1.3.6.1.4.1.388.1.5.2.11.8.1.4
The cost to be added to the root path cost field in the config BPDU (Bridge Protocol Data Unit) received on this interface in order to determine the cost of the path to the root WLAP.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER  

apDsgnatedRoot 1.3.6.1.4.1.388.1.5.2.11.8.1.5
The unique Root AP ID designated by the Root AP.
Status: mandatory Access: read-only
OBJECT-TYPE    
  OCTET STRING Size(1..8)  

apDsgnatedCost 1.3.6.1.4.1.388.1.5.2.11.8.1.6
The cost of the path to the Root AP designated by the Root AP.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER  

apDsgnatedWLAP 1.3.6.1.4.1.388.1.5.2.11.8.1.7
The unique WLAP ID designated by the Root AP.
Status: mandatory Access: read-only
OBJECT-TYPE    
  OCTET STRING Size(1..8)  

apDsgnatedItf 1.3.6.1.4.1.388.1.5.2.11.8.1.8
The WLAP interface ID designated by the Root AP.
Status: mandatory Access: read-only
OBJECT-TYPE    
  OCTET STRING Size(1..2)  

apRetryHistogramTable 1.3.6.1.4.1.388.1.5.2.12
A table of Retry statistics, which is based on number of packets with various retries over time. The current number of entries is 16.
Status: mandatory Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    ApRetryHistogramEntry

apRetryHistogramEntry 1.3.6.1.4.1.388.1.5.2.12.1
An entry in the table of Retry Histogram, which is based on number of packets with various retries over time. A row in this table cannot be created or deleted by SNMP operations on columns of the table.
Status: mandatory Access: not-accessible
OBJECT-TYPE    
  ApRetryHistogramEntry  

apRetryHistogramIndex 1.3.6.1.4.1.388.1.5.2.12.1.1
Number of retries index. Range (1..16).
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER 1..16  

apNumberOfRetries 1.3.6.1.4.1.388.1.5.2.12.1.2
Packets with this Number of retries. Range (0..15).
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER 0..15  

apPacketsHistogramCounts 1.3.6.1.4.1.388.1.5.2.12.1.3
Counter for the packets per number of retries.
Status: mandatory Access: read-only
OBJECT-TYPE    
  Counter  

apDSPerFreqStatTable 1.3.6.1.4.1.388.1.5.2.13
A table of Radio Per Frequency statistics, which is based on the historical frequency records used by this Access Point. The current number of entries is 78.
Status: mandatory Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    ApDSPerFreqStatEntry

apDSPerFreqStatEntry 1.3.6.1.4.1.388.1.5.2.13.1
An entry in the table of Radio per frequency statistics. A row in this table cannot be created or deleted by SNMP operations on columns of the table.
Status: mandatory Access: not-accessible
OBJECT-TYPE    
  ApDSPerFreqStatEntry  

rfDSFrequency 1.3.6.1.4.1.388.1.5.2.13.1.1
Radio Frequency channel number.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER  

rfDSPerFqPktsSents 1.3.6.1.4.1.388.1.5.2.13.1.2
Counter for the packets sent per frequency.
Status: mandatory Access: read-only
OBJECT-TYPE    
  Counter  

rfDSPerFqPktsRcvds 1.3.6.1.4.1.388.1.5.2.13.1.3
Counter for the packets received per frequency.
Status: mandatory Access: read-only
OBJECT-TYPE    
  Counter  

rfDSPerFqRetries 1.3.6.1.4.1.388.1.5.2.13.1.4
Counter for the retries per frequency.
Status: mandatory Access: read-only
OBJECT-TYPE    
  Counter  

apAgentAdSents 1.3.6.1.4.1.388.1.5.2.14.1
Counter for the number agent advertisement sent.
Status: mandatory Access: read-only
OBJECT-TYPE    
  Counter  

apRegRequestRcvds 1.3.6.1.4.1.388.1.5.2.14.2
Counter for the number registration request received.
Status: mandatory Access: read-only
OBJECT-TYPE    
  Counter  

apRegReplySents 1.3.6.1.4.1.388.1.5.2.14.3
Counter for the number registration reply sent.
Status: mandatory Access: read-only
OBJECT-TYPE    
  Counter  

apClrAllStatistics 1.3.6.1.4.1.388.1.5.3.1
Clear all the interface statistics (yes = 1, no = 2).
Status: mandatory Access: read-write
OBJECT-TYPE    
  INTEGER yes(1), no(2)  

apClrMUTable 1.3.6.1.4.1.388.1.5.3.2
Clear the MU Table (yes = 1, no = 2).
Status: mandatory Access: read-write
OBJECT-TYPE    
  INTEGER yes(1), no(2)  

apClrACL 1.3.6.1.4.1.388.1.5.3.3
Clear the Access Control Table (yes = 1, no = 2).
Status: mandatory Access: read-write
OBJECT-TYPE    
  INTEGER yes(1), no(2)  

apClrACLRangeTable 1.3.6.1.4.1.388.1.5.3.4
Clear the Access Control Range Table (yes = 1, no = 2).
Status: mandatory Access: read-write
OBJECT-TYPE    
  INTEGER yes(1), no(2)  

apClrAddrFilterTbl 1.3.6.1.4.1.388.1.5.3.5
Clear the Address Filtering Table (yes = 1, no = 2).
Status: mandatory Access: read-write
OBJECT-TYPE    
  INTEGER yes(1), no(2)  

apLdACLFrMUList 1.3.6.1.4.1.388.1.5.3.6
Load the Access Control Table from MU Table (yes = 1, no = 2).
Status: mandatory Access: read-write
OBJECT-TYPE    
  INTEGER yes(1), no(2)  

apModemDialOut 1.3.6.1.4.1.388.1.5.3.7
Commands the modem to dialout (yes = 1, no = 2).
Status: mandatory Access: read-write
OBJECT-TYPE    
  INTEGER yes(1), no(2)  

apModemHangUp 1.3.6.1.4.1.388.1.5.3.8
Forces the AP to issue a 'hangup' string to the modem attached to the serial port (yes = 1, no = 2). This command is meaning-ful only if the AP is configured for a modem connection on the serial port. If there is no modem or there is no connection, the command will be ignored.
Status: mandatory Access: read-write
OBJECT-TYPE    
  INTEGER yes(1), no(2)  

apUpdateFirmware 1.3.6.1.4.1.388.1.5.3.9
Update the AP firmware through TFTP server. The AP firmware will be saved in NVRAM (yes = 1, no = 2). Before issuing this command, set 'apDnLdFileName', and 'apTFTPServer' to the proper values.
Status: mandatory Access: read-write
OBJECT-TYPE    
  INTEGER yes(1), no(2)  

apDnLdFileName 1.3.6.1.4.1.388.1.5.3.10
The name of the file to be downloaded to the AP. (Including path name and total up to 49 characters.) Note: IF DHCP is responded to, that name will take precedence and overwrite this name.
Status: mandatory Access: read-write
OBJECT-TYPE    
  DisplayString Size(1..50)  

apTFTPServer 1.3.6.1.4.1.388.1.5.3.11
The IP address for the TFTP Server. Note: IF DHCP is responded to, that IP address will take precedence and overwrite this setting.
Status: mandatory Access: read-write
OBJECT-TYPE    
  IpAddress  

apResetAP 1.3.6.1.4.1.388.1.5.3.12
Forces a reset of the AP (yes = 1, no = 2). Upon reset, the AP clears all the statistics and restores the last saved configuration information. If changes are made without being saved, the AP clears those changes upon reset.
Status: mandatory Access: read-write
OBJECT-TYPE    
  INTEGER yes(1), no(2)  

apHTMLFileName 1.3.6.1.4.1.388.1.5.3.13
The name of the HTML file to be downloaded to the AP. (Including path name and total up to 49 characters.) Note: IF DHCP is responded to, that name will take precedence and overwrite this name.
Status: mandatory Access: read-write
OBJECT-TYPE    
  DisplayString Size(1..50)  

apUpdateHTMLFile 1.3.6.1.4.1.388.1.5.3.14
Update the AP HTML file through TFTP server. The AP HTML file will be saved in NVRAM (yes = 1, no = 2). Before issuing this command, set 'apHTMLFileName', and 'apTFTPServer' to the proper values.
Status: mandatory Access: read-write
OBJECT-TYPE    
  INTEGER yes(1), no(2)  

apDHCPEnable 1.3.6.1.4.1.388.1.5.3.15
Enables/Disables DHCP mode for the AP. Default is disabled(2).
Status: mandatory Access: read-write
OBJECT-TYPE    
  INTEGER enabled(1), disabled(2)  

apUpdAllAPsFirmware 1.3.6.1.4.1.388.1.5.3.16
Update all APs firmware on this network which share the same NetID through TFTP server. The AP firmware will be saved in NVRAM (yes = 1, no = 2). Before issuing this command, set 'apDnLdFileName', and 'apTFTPServer' to the proper values.
Status: mandatory Access: read-write
OBJECT-TYPE    
  INTEGER yes(1), no(2)  

apUpdAllAPsHTMLFile 1.3.6.1.4.1.388.1.5.3.17
Update all APs HTML file on this network which share the same NetID through TFTP server. The AP HTML file will be saved in NVRAM (yes = 1, no = 2). Before issuing this command, set 'apHTMLFileName', and 'apTFTPServer' to the proper values.
Status: mandatory Access: read-write
OBJECT-TYPE    
  INTEGER yes(1), no(2)  

apTFTPUpdBothFiles 1.3.6.1.4.1.388.1.5.3.18
Update Both HTML file and Firmware for this Access Point The AP HTML file will be saved in NVRAM (yes = 1, no = 2). Before issuing this command, set 'apHTMLFileName', and 'apTFTPServer' to the proper values.
Status: mandatory Access: read-write
OBJECT-TYPE    
  INTEGER yes(1), no(2)  

apHelpURL 1.3.6.1.4.1.388.1.5.3.19
The name of the HTML Help file . (Including path name and total up to 39 characters.)
Status: mandatory Access: read-write
OBJECT-TYPE    
  DisplayString Size(1..40)  

apFileUpdateStatus 1.3.6.1.4.1.388.1.5.3.20
Reports the Firmware/HTML file download and update status.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER download-successful(1), too-many-XMODEM-errors(2), xmodem-transfer-cancelled(3), xmodem-packets-out-of-order(4), tftp-server-unreachable(5), no-ARP-response-from-server(6), no-TFTP-service-on-server(7), firmware-file-not-found(8), html-file-not-found(9), bad-permissions-for-firmware-file(10), unable-to-open-firmware-file(11), unable-to-open-HTML-file(12), error-during-TFTP-download(13), too-many-TFTP-retries(14), corrupted-firmware-file(15), general-download-failure(16)  

apFlashLEDs 1.3.6.1.4.1.388.1.5.3.21
When this command is issued, it forces all status LEDs on the AP to start flashing. This command is primarily used for physically locating the AP where multiple APs are deployed. (yes = 1, no = 2) Default is no.
Status: mandatory Access: read-write
OBJECT-TYPE    
  INTEGER yes(1), no(2)  

apACLViolations 1.3.6.1.4.1.388.1.5.4.1
Indicates the number of Access Control violations occurred.
Status: mandatory Access: read-only
OBJECT-TYPE    
  Counter  

apSaveConfig 1.3.6.1.4.1.388.1.5.4.2
Saves the current configuration to NVRAM (yes = 1, no = 2).
Status: mandatory Access: read-write
OBJECT-TYPE    
  INTEGER yes(1), no(2)  

apAccCtrlTable 1.3.6.1.4.1.388.1.5.4.3
A table of MAC addresses allowed to associate with the Access Point. The maximum number of entries in the table is 512.
Status: mandatory Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    ApAccCtrlEntry

apAccCtrlEntry 1.3.6.1.4.1.388.1.5.4.3.1
An entry in the table of MAC address Access Control. A row in this table is created by setting the value of allowedMU to the MAC address of the MU allowed to associate with this Access Point. A row in this table is deleted by setting the value of allowedMU to '000000000000'.
Status: mandatory Access: not-accessible
OBJECT-TYPE    
  ApAccCtrlEntry  

allowedIndex 1.3.6.1.4.1.388.1.5.4.3.1.1
Access Control Table index. Range (1..512).
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER 1..512  

allowedMU 1.3.6.1.4.1.388.1.5.4.3.1.2
MU MAC address which is allowed to associate with this AP.
Status: mandatory Access: read-write
OBJECT-TYPE    
  PhysAddress  

apACLRangeTable 1.3.6.1.4.1.388.1.5.4.4
A table of Access Control Range, which consists of eight (8) pairs of low and high MAC addresses. Any Mobile Unit with the MAC address within the range is allowed to associate with the Access Point. The maximum number of entries in the table is 8.
Status: mandatory Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    ApACLRangeEntry

apACLRangeEntry 1.3.6.1.4.1.388.1.5.4.4.1
An entry in the table of MAC address Access Control Range. A row in this table is created by first setting the value of lowMacAddr to the lowest MAC address and then the value of highMacAddr to the highest MAC address of a group of Mobile Units allowed to associate with this Access Point. This sequence of setting is very important, otherwise a wrong result will occur. A row in this table is deleted by setting the value of either lowMacAddr or highMacAddr to '000000000000'.
Status: mandatory Access: not-accessible
OBJECT-TYPE    
  ApACLRangeEntry  

apACLRangeIndex 1.3.6.1.4.1.388.1.5.4.4.1.1
Access Control Range Table index. Range (1..8).
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER 1..8  

lowMacAddr 1.3.6.1.4.1.388.1.5.4.4.1.2
The lowest Mobile Unit MAC address in the range which is allowed to be associated with this AP. Note: When setting the ACL range, Both lowMacAddr and highMacAddr have to be set in order for the ACL range setting to take effect. lowMacAddr should be entered first. lowMacAddr < highMacAddr
Status: mandatory Access: read-write
OBJECT-TYPE    
  PhysAddress  

highMacAddr 1.3.6.1.4.1.388.1.5.4.4.1.3
The highest Mobile Unit MAC address in the range which is allowed to be associated with this AP. Note: When setting the ACL range, Both lowMacAddr and highMacAddr have to be set in order for the ACL range setting to take effect. highMacAddr should be entered last. highMacAddr > lowMacAddr
Status: mandatory Access: read-write
OBJECT-TYPE    
  PhysAddress  

apSaveConfigAllAPs 1.3.6.1.4.1.388.1.5.4.5
Saves the current configuration to NVRAM for all APs on this network which share the same NetID(yes = 1, no = 2).
Status: mandatory Access: read-write
OBJECT-TYPE    
  INTEGER yes(1), no(2)  

apWEPLicenseKey 1.3.6.1.4.1.388.1.5.4.6
This is a license key (a string of 18 alphanumeric characters). It is arranaged as follows: xxxx-yyyyyyy-zzzzzzz xxxx : vendor specific ID code ( 4 alphabetical characters) -yyyyyyy-zzzzzzz : a string of 14 alphanumeric characters Note: It is important to insert the hyphens in as shown. When entered and authenticated by the AP, the Strong(128 bit) encryption is enabled. Check the state of ap128bWEPFlag object.
Status: mandatory Access: read-write
OBJECT-TYPE    
  DisplayString Size(1..20)  

ap128bWEPFlag 1.3.6.1.4.1.388.1.5.4.7
When enabled, This flag indicates that AP is enabled to supports strong(128 bit) Encryption. The state of this flag is internally set only by the AP. when a valid access code is entered for apWEPLicenseKey object and accepted the AP will set the state of this flag to enabled. Default is disabled.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER enabled(1), disabled(2)