SWL3MGMT-MIB

File: SWL3MGMT-MIB.mib (49188 bytes)

Imported modules

SNMPv2-SMI SNMPv2-TC SWPRIMGMT-MIB
OSPF-MIB IF-MIB

Imported symbols

Counter32 MODULE-IDENTITY OBJECT-TYPE
IpAddress NOTIFICATION-TYPE PhysAddress
DisplayString RowStatus MacAddress
TruthValue TimeStamp privateMgmt
TOSType Metric AreaID
ifIndex

Defined Types

NodeAddress  
OCTET STRING Size(6)    

NetAddress  
OCTET STRING Size(4)    

SwL3IpCtrlEntry  
SEQUENCE    
  swL3IpCtrlInterfaceName DisplayString
  swL3IpCtrlIfIndex INTEGER
  swL3IpCtrlIpAddr IpAddress
  swL3IpCtrlIpSubnetMask IpAddress
  swL3IpCtrlVlanName DisplayString
  swL3IpCtrlMode INTEGER
  swL3IpCtrlState RowStatus
  swL3IpCtrlOperState INTEGER

SwL3IpFdbInfoEntry  
SEQUENCE    
  swL3IpFdbInfoIpAddr IpAddress
  swL3IpFdbInfoIpSubnetMask IpAddress
  swL3IpFdbInfoPort INTEGER
  swL3IpFdbInfoType INTEGER

SwL3IpFilterAddrCtrlEntry  
SEQUENCE    
  swL3IpFilterAddrIpAddr IpAddress
  swL3IpFilterAddrCtrlState INTEGER

SwL3IpStaticRouteEntry  
SEQUENCE    
  swL3IpStaticRouteDest IpAddress
  swL3IpStaticRouteMask IpAddress
  swL3IpStaticRouteNextHop IpAddress
  swL3IpStaticRouteMetric INTEGER
  swL3IpStaticRouteStatus INTEGER

SwL3IpArpEntry  
SEQUENCE    
  swL3IpArpIfIndex INTEGER
  swL3IpArpNetAddress IpAddress
  swL3IpArpPhysAddress MacAddress
  swL3IpArpType INTEGER
  swL3IpArpDynamicAgingTime INTEGER

SwL3RelayBootpCtrlEntry  
SEQUENCE    
  swL3RelayBootpCtrlInterfaceName DisplayString
  swL3RelayBootpCtrlServer IpAddress
  swL3RelayBootpCtrlState INTEGER

SwL3RelayDnsCtrlEntry  
SEQUENCE    
  swL3RelayDnsCtrlDomainName DisplayString
  swL3RelayDnsCtrlIpAddr IpAddress
  swL3RelayDnsCtrlState INTEGER

SwL3Md5Entry  
SEQUENCE    
  swL3Md5KeyId INTEGER
  swL3Md5Key DisplayString
  swL3Md5State INTEGER

SwL3RouteRedistriEntry  
SEQUENCE    
  swL3RouteRedistriSrcProtocol INTEGER
  swL3RouteRedistriDstProtocol INTEGER
  swL3RouteRedistriType INTEGER
  swL3RouteRedistriMetric INTEGER
  swL3RouteRedistriState INTEGER

SwL3OspfHostEntry  
SEQUENCE    
  swL3OspfHostIpAddress IpAddress
  swL3OspfHostTOS TOSType
  swL3OspfHostMetric Metric
  swL3OspfHostStatus RowStatus
  swL3OspfHostAreaID AreaID

SwL3VrrpOperEntry  
SEQUENCE    
  swL3VrrpOperVrId INTEGER
  swL3VrrpOperCriticalIpAddr IpAddress
  swL3VrrpOperCriticalIpState INTEGER
  swL3VrrpOperHoldDownTimer INTEGER

SwL3RoutePrefEntry  
SEQUENCE    
  swL3RoutePrefProtocol INTEGER
  swL3RoutePrefValue INTEGER

SwL3DvmrpInterfaceEntry  
SEQUENCE    
  swL3DvmrpInterfaceIfIndex INTEGER
  swL3DvmrpInterfaceNeighborTimeout INTEGER
  swL3DvmrpInterfaceProbe INTEGER

Defined Values

swL3MgmtMIB 1.3.6.1.4.1.2272.1.201.1.3
The Structure of Layer 3 Network Management Information for the proprietary enterprise.
MODULE-IDENTITY    

swL3DevMgmt 1.3.6.1.4.1.2272.1.201.1.3.1
OBJECT IDENTIFIER    

swL3IpMgmt 1.3.6.1.4.1.2272.1.201.1.3.2
OBJECT IDENTIFIER    

swL3RelayMgmt 1.3.6.1.4.1.2272.1.201.1.3.3
OBJECT IDENTIFIER    

swL3IpCtrlMgmt 1.3.6.1.4.1.2272.1.201.1.3.2.1
OBJECT IDENTIFIER    

swL3IpFdbMgmt 1.3.6.1.4.1.2272.1.201.1.3.2.2
OBJECT IDENTIFIER    

swL3IpFilterMgmt 1.3.6.1.4.1.2272.1.201.1.3.2.3
OBJECT IDENTIFIER    

swL3RelayBootpMgmt 1.3.6.1.4.1.2272.1.201.1.3.3.1
OBJECT IDENTIFIER    

swL3RelayDnsMgmt 1.3.6.1.4.1.2272.1.201.1.3.3.2
OBJECT IDENTIFIER    

swL3DevCtrl 1.3.6.1.4.1.2272.1.201.1.3.1.1
OBJECT IDENTIFIER    

swL3DevCtrlRIPState 1.3.6.1.4.1.2272.1.201.1.3.1.1.1
This object indicates Routing Information Protocol (RIP) version 2 function is enabled or disabled.
OBJECT-TYPE    
  INTEGER other(1), disabled(2), enabled(3)  

swL3DevCtrlOSPFState 1.3.6.1.4.1.2272.1.201.1.3.1.1.2
This object indicates OSPF protocol is enabled or disabled.
OBJECT-TYPE    
  INTEGER other(1), disabled(2), enabled(3)  

swL3DevCtrlDVMRPState 1.3.6.1.4.1.2272.1.201.1.3.1.1.3
This object indicates DVMRP protocol is enabled or disabled.
OBJECT-TYPE    
  INTEGER other(1), disabled(2), enabled(3)  

swL3DevCtrlVRRPState 1.3.6.1.4.1.2272.1.201.1.3.1.1.4
This object indicates VRRP protocol is enabled or disabled.
OBJECT-TYPE    
  INTEGER other(1), disabled(2), enabled(3)  

swL3DevCtrlVRRPPingVirtualAddrState 1.3.6.1.4.1.2272.1.201.1.3.1.1.5
This object let host can ping the virtual ip address or not. Default is disabled(2).
OBJECT-TYPE    
  INTEGER other(1), disabled(2), enabled(3)  

swL3IpCtrlTable 1.3.6.1.4.1.2272.1.201.1.3.2.1.1
This table contain IP interface information.
OBJECT-TYPE    
  SEQUENCE OF  
    SwL3IpCtrlEntry

swL3IpCtrlEntry 1.3.6.1.4.1.2272.1.201.1.3.2.1.1.1
A list of information about a specific IP interface.
OBJECT-TYPE    
  SwL3IpCtrlEntry  

swL3IpCtrlInterfaceName 1.3.6.1.4.1.2272.1.201.1.3.2.1.1.1.1
This object indicates the name of the IP interface.
OBJECT-TYPE    
  DisplayString Size(0..12)  

swL3IpCtrlIfIndex 1.3.6.1.4.1.2272.1.201.1.3.2.1.1.1.2
This object uniquely identifies the IP interface number in the swL3IpCtrlTable.
OBJECT-TYPE    
  INTEGER 0..65535  

swL3IpCtrlIpAddr 1.3.6.1.4.1.2272.1.201.1.3.2.1.1.1.3
The IP address of the interface. This object only can take the value of the unicast IP address.
OBJECT-TYPE    
  IpAddress  

swL3IpCtrlIpSubnetMask 1.3.6.1.4.1.2272.1.201.1.3.2.1.1.1.4
The IP net mask for this interface.
OBJECT-TYPE    
  IpAddress  

swL3IpCtrlVlanName 1.3.6.1.4.1.2272.1.201.1.3.2.1.1.1.5
This object indicates the IP control entry's VLAN name. The VLAN name in each entry must be unique in the IP Control Table.
OBJECT-TYPE    
  DisplayString Size(0..32)  

swL3IpCtrlMode 1.3.6.1.4.1.2272.1.201.1.3.2.1.1.1.6
This object indicates the IP operation mode. other(1) - this entry is currently in use but the conditions under which it will remain so are different from each of the following values. manual(2) - the IP address will be set by manual. bootp(3) - the IP address will be set automatically from BOOTP server. dhcp(4) - the IP address will be set automatically from DHCP server.
OBJECT-TYPE    
  INTEGER other(1), manual(2), bootp(3), dhcp(4)  

swL3IpCtrlState 1.3.6.1.4.1.2272.1.201.1.3.2.1.1.1.7
This variable displays the status of the entry. The status used for creating, modifying, and deleting instances of the objects in this table.
OBJECT-TYPE    
  RowStatus  

swL3IpCtrlOperState 1.3.6.1.4.1.2272.1.201.1.3.2.1.1.1.8
The current operational state of the IP interface.
OBJECT-TYPE    
  INTEGER other(1), up(2), down(3)  

swL3IpFdbInfoTable 1.3.6.1.4.1.2272.1.201.1.3.2.2.1
A table that contains forwarding and/or filtering information. This information is used by the switch in determining how to propagate the received IP packets.
OBJECT-TYPE    
  SEQUENCE OF  
    SwL3IpFdbInfoEntry

swL3IpFdbInfoEntry 1.3.6.1.4.1.2272.1.201.1.3.2.2.1.1
Information about a specific IP address for which the bridge has some forwarding and/or filtering information.
OBJECT-TYPE    
  SwL3IpFdbInfoEntry  

swL3IpFdbInfoIpAddr 1.3.6.1.4.1.2272.1.201.1.3.2.2.1.1.1
A IP address for which switch has forwarding and/or filtering information.
OBJECT-TYPE    
  IpAddress  

swL3IpFdbInfoIpSubnetMask 1.3.6.1.4.1.2272.1.201.1.3.2.2.1.1.2
A IP net mask for this interface.for which switch has forwarding and/or filtering information.
OBJECT-TYPE    
  IpAddress  

swL3IpFdbInfoPort 1.3.6.1.4.1.2272.1.201.1.3.2.2.1.1.3
Either the value '0', or the port number of the port on which packet having a IP address equal to the value of the corresponding instance of swL3IpFdbInfoIpAddr has been seen. A value of '0' indicates that the port number has not been learned but that switch does have some forwarding/filtering information about this address.
OBJECT-TYPE    
  INTEGER 0..65535  

swL3IpFdbInfoType 1.3.6.1.4.1.2272.1.201.1.3.2.2.1.1.4
The status of this entry.
OBJECT-TYPE    
  INTEGER other(1), static(2), dynamic(3)  

swL3IpFilterAddrConfig 1.3.6.1.4.1.2272.1.201.1.3.2.3.1
OBJECT IDENTIFIER    

swL3IpFilterAddrMaxSupportedEntries 1.3.6.1.4.1.2272.1.201.1.3.2.3.1.1
Maximum number of entries in the IP address filtering table (swL3IpFilterAddrCtrlTable) .
OBJECT-TYPE    
  INTEGER 0..65535  

swL3IpFilterAddrCurrentTotalEntries 1.3.6.1.4.1.2272.1.201.1.3.2.3.1.2
Current applied number of entries in the IP address filtering table. If the swL3IpFilterAddrCtrlState = dst-src-addr, then it means there are two entries in swL3IpFilterAddrCtrlTable.
OBJECT-TYPE    
  INTEGER 0..65535  

swL3IpFilterAddrCtrlTable 1.3.6.1.4.1.2272.1.201.1.3.2.3.1.3
This table defines information for the device to filter packets with specific IP address (either as the DA and/or as the SA). The IP address can be a unicast address or multicast address. This table has higher priority than both static FDB table and IGMP table. It means that if a IP address appears on this table also appears on the static FDB table, the device will use the information provide by this table to process the packet.
OBJECT-TYPE    
  SEQUENCE OF  
    SwL3IpFilterAddrCtrlEntry

swL3IpFilterAddrCtrlEntry 1.3.6.1.4.1.2272.1.201.1.3.2.3.1.3.1
A list of information about a specific unicast/multicast IP address for which the switch has filtering information.
OBJECT-TYPE    
  SwL3IpFilterAddrCtrlEntry  

swL3IpFilterAddrIpAddr 1.3.6.1.4.1.2272.1.201.1.3.2.3.1.3.1.1
This object indicates a unicast/multicast IP address for which the switch has filtering information. But if the swL3IpFilterAddrCtrlState = src-addr, then the object can not be a multicast IP address (Class D IP address).
OBJECT-TYPE    
  IpAddress  

swL3IpFilterAddrCtrlState 1.3.6.1.4.1.2272.1.201.1.3.2.3.1.3.1.2
This object indicates the status of this entry. other(1) - this entry is currently in use but the conditions under which it will remain so are different from each of the following values. dst-addr(2) - recieved frames's destination address are currently used to be filtered as it meets with the IP address entry of the table. src-addr(3) - recieved frames's source address are currently used to be filtered as it meets with the IP address entry of the table. dst-src-addr(4) - recieved frames's destination address or source address are currently used to be filtered as it meets with the IP address entry of the table. invalid(5) - writing this value to the object, and then the corresponding entry will be removed from the table.
OBJECT-TYPE    
  INTEGER other(1), dst-addr(2), src-addr(3), dst-src-addr(4), invalid(5)  

swL3IpArpAgingTime 1.3.6.1.4.1.2272.1.201.1.3.2.4
The timeout period in minutes for aging out dynamically learned arp information.
OBJECT-TYPE    
  INTEGER 0..65535  

swL3IpStaticRouteTable 1.3.6.1.4.1.2272.1.201.1.3.2.5
This entity's IP static Routing table.
OBJECT-TYPE    
  SEQUENCE OF  
    SwL3IpStaticRouteEntry

swL3IpStaticRouteEntry 1.3.6.1.4.1.2272.1.201.1.3.2.5.1
A particular route to a particular destination, under a particular policy.
OBJECT-TYPE    
  SwL3IpStaticRouteEntry  

swL3IpStaticRouteDest 1.3.6.1.4.1.2272.1.201.1.3.2.5.1.1
The destination IP address of this route. This object may not take a Multicast (Class D) address value. Any assignment (implicit or otherwise) of an instance of this object to a value x must be rejected if the bitwise logical-AND of x with the value of the corresponding instance of the swL3IpStaticRouteMask object is not equal to x.
OBJECT-TYPE    
  IpAddress  

swL3IpStaticRouteMask 1.3.6.1.4.1.2272.1.201.1.3.2.5.1.2
Indicate the mask to be logical-ANDed with the destination address before being compared to the value in the swL3IpStaticRouteDest field. For those systems that do not support arbitrary subnet masks, an agent constructs the value of the swL3IpStaticRouteMask by reference to the IP Address Class. Any assignment (implicit or otherwise) of an instance of this object to a value x must be rejected if the bitwise logical-AND of x with the value of the corresponding instance of the swL3IpStaticRouteDest object is not equal to swL3IpStaticRouteDest.
OBJECT-TYPE    
  IpAddress  

swL3IpStaticRouteNextHop 1.3.6.1.4.1.2272.1.201.1.3.2.5.1.3
On remote routes, the address of the next sys- tem en route; Otherwise, 0.0.0.0.
OBJECT-TYPE    
  IpAddress  

swL3IpStaticRouteMetric 1.3.6.1.4.1.2272.1.201.1.3.2.5.1.4
The routing metric for this route.
OBJECT-TYPE    
  INTEGER 1..65535  

swL3IpStaticRouteStatus 1.3.6.1.4.1.2272.1.201.1.3.2.5.1.5
This object indicates the status of this entry. other(1) - this entry is currently in use but the conditions under which it will remain so are different from each of the following values. invalid(2) - writing this value to the object, and then the corresponding entry will be removed from the table. valid(3) - this entry is reside in the table.
OBJECT-TYPE    
  INTEGER other(1), invalid(2), valid(3)  

swL3IpArpTable 1.3.6.1.4.1.2272.1.201.1.3.2.6
The ARP table used for mapping from IP addresses to physical addresses.
OBJECT-TYPE    
  SEQUENCE OF  
    SwL3IpArpEntry

swL3IpArpEntry 1.3.6.1.4.1.2272.1.201.1.3.2.6.1
Each entry contains one IpAddress to `physical' address equivalence.
OBJECT-TYPE    
  SwL3IpArpEntry  

swL3IpArpIfIndex 1.3.6.1.4.1.2272.1.201.1.3.2.6.1.1
The interface on which this entry's equivalence is effective. The interface identified by a particular value of this index is the same interface as identified by the same value of ifIndex.
OBJECT-TYPE    
  INTEGER  

swL3IpArpNetAddress 1.3.6.1.4.1.2272.1.201.1.3.2.6.1.2
The IpAddress corresponding to the media-dependent `physical' address.
OBJECT-TYPE    
  IpAddress  

swL3IpArpPhysAddress 1.3.6.1.4.1.2272.1.201.1.3.2.6.1.3
The media-dependent `physical' address.
OBJECT-TYPE    
  MacAddress  

swL3IpArpType 1.3.6.1.4.1.2272.1.201.1.3.2.6.1.4
The type of mapping. Setting this object to the value invalid(2) has the effect of invalidating the corresponding entry in the swL3IpArpTable. That is, it effectively dissasociates the interface identified with said entry from the mapping identified with said entry. It is an implementation-specific matter as to whether the agent removes an invalidated entry from the table. Accordingly, management stations must be prepared to receive tabular information from agents that corresponds to entries not currently in use. Proper interpretation of such entries requires examination of the relevant swL3IpArpType object.
OBJECT-TYPE    
  INTEGER other(1), invalid(2), dynamic(3), static(4), local(5), local-broadcast(6)  

swL3IpArpDynamicAgingTime 1.3.6.1.4.1.2272.1.201.1.3.2.6.1.5
The timeout period in seconds for aging out dynamically learned arp information. If the swL3IpArpType is not dynamic(3), this object will display zero.
OBJECT-TYPE    
  INTEGER 0..65535  

swL3IpArpReqRateLimitState 1.3.6.1.4.1.2272.1.201.1.3.2.7
To enable limit ARP requests trapped to CPU or disabled.
OBJECT-TYPE    
  INTEGER other(1), disabled(2), enabled(3)  

swL3IpArpReqRateLimitValue 1.3.6.1.4.1.2272.1.201.1.3.2.8
To configure how much frames per second that ARP request limit. This value will be usefull only when swL3IpArpReqRateLimitState is enabled.
OBJECT-TYPE    
  INTEGER 10..100  

swL3RelayBootpState 1.3.6.1.4.1.2272.1.201.1.3.3.1.1
This object indicates BOOTP Relay function is enabled or disabled.
OBJECT-TYPE    
  INTEGER other(1), disabled(2), enabled(3)  

swL3RelayBootpHopCount 1.3.6.1.4.1.2272.1.201.1.3.3.1.2
This object indicates the maximum number of router hops that the BOOTP packets can cross.
OBJECT-TYPE    
  INTEGER 0..65535  

swL3RelayBootpTimeThreshold 1.3.6.1.4.1.2272.1.201.1.3.3.1.3
This object indicates the minimum time in seconds within which the switch must relay the BOOTP request. If this time is exceeded, the switch will drop the BOOTP packet.
OBJECT-TYPE    
  INTEGER 0..65535  

swL3RelayBootpCtrlTable 1.3.6.1.4.1.2272.1.201.1.3.3.1.4
This table specifys the IP address as a destination to forward (relay) BOOTP packets to.
OBJECT-TYPE    
  SEQUENCE OF  
    SwL3RelayBootpCtrlEntry

swL3RelayBootpCtrlEntry 1.3.6.1.4.1.2272.1.201.1.3.3.1.4.1
A list of information specifies the IP address as a destination to forward (relay) BOOTP packets to.
OBJECT-TYPE    
  SwL3RelayBootpCtrlEntry  

swL3RelayBootpCtrlInterfaceName 1.3.6.1.4.1.2272.1.201.1.3.3.1.4.1.1
The name of the IP interface.
OBJECT-TYPE    
  DisplayString Size(0..12)  

swL3RelayBootpCtrlServer 1.3.6.1.4.1.2272.1.201.1.3.3.1.4.1.2
The BOOTP server IP address.
OBJECT-TYPE    
  IpAddress  

swL3RelayBootpCtrlState 1.3.6.1.4.1.2272.1.201.1.3.3.1.4.1.3
This object indicates the status of this entry. other(1) - this entry is currently in use but the conditions under which it will remain so are different from each of the following values. invalid(2) - writing this value to the object, and then the corresponding entry will be removed from the table. valid(3) - this entry is reside in the table.
OBJECT-TYPE    
  INTEGER other(1), invalid(2), valid(3)  

swL3RelayDnsState 1.3.6.1.4.1.2272.1.201.1.3.3.2.1
This object indicates DNS Relay function is enabled or disabled.
OBJECT-TYPE    
  INTEGER other(1), disabled(2), enabled(3)  

swL3RelayDnsPrimaryServer 1.3.6.1.4.1.2272.1.201.1.3.3.2.2
This object indicates the address of the primary DNS server.
OBJECT-TYPE    
  IpAddress  

swL3RelayDnsSecondaryServer 1.3.6.1.4.1.2272.1.201.1.3.3.2.3
This object indicates the address of the secondary DNS server.
OBJECT-TYPE    
  IpAddress  

swL3RelayDnsCacheState 1.3.6.1.4.1.2272.1.201.1.3.3.2.4
This object indicates DNS Relay cache is enabled or disabled.
OBJECT-TYPE    
  INTEGER other(1), disabled(2), enabled(3)  

swL3RelayDnsStaticTableState 1.3.6.1.4.1.2272.1.201.1.3.3.2.5
This object indicates DNS Relay static table is enabled or disabled.
OBJECT-TYPE    
  INTEGER other(1), disabled(2), enabled(3)  

swL3RelayDnsCtrlTable 1.3.6.1.4.1.2272.1.201.1.3.3.2.6
This table display the current DNS relay static table.
OBJECT-TYPE    
  SEQUENCE OF  
    SwL3RelayDnsCtrlEntry

swL3RelayDnsCtrlEntry 1.3.6.1.4.1.2272.1.201.1.3.3.2.6.1
A list of information display the current DNS relay static table.
OBJECT-TYPE    
  SwL3RelayDnsCtrlEntry  

swL3RelayDnsCtrlDomainName 1.3.6.1.4.1.2272.1.201.1.3.3.2.6.1.1
The domain name of the entry.
OBJECT-TYPE    
  DisplayString Size(0..255)  

swL3RelayDnsCtrlIpAddr 1.3.6.1.4.1.2272.1.201.1.3.3.2.6.1.2
The IP address of the entry.
OBJECT-TYPE    
  IpAddress  

swL3RelayDnsCtrlState 1.3.6.1.4.1.2272.1.201.1.3.3.2.6.1.3
This object indicates the status of this entry. other(1) - this entry is currently in use but the conditions under which it will remain so are different from each of the following values. invalid(2) - writing this value to the object, and then the corresponding entry will be removed from the table. valid(3) - this entry is reside in the table.
OBJECT-TYPE    
  INTEGER other(1), invalid(2), valid(3)  

swL3Md5Table 1.3.6.1.4.1.2272.1.201.1.3.4
This table display the current MD5 key table.
OBJECT-TYPE    
  SEQUENCE OF  
    SwL3Md5Entry

swL3Md5Entry 1.3.6.1.4.1.2272.1.201.1.3.4.1
A list of information display the current MD5 key table.
OBJECT-TYPE    
  SwL3Md5Entry  

swL3Md5KeyId 1.3.6.1.4.1.2272.1.201.1.3.4.1.1
The MD5 key ID.
OBJECT-TYPE    
  INTEGER 1..255  

swL3Md5Key 1.3.6.1.4.1.2272.1.201.1.3.4.1.2
An MD5 password of up to 16 bytes.
OBJECT-TYPE    
  DisplayString Size(1..16)  

swL3Md5State 1.3.6.1.4.1.2272.1.201.1.3.4.1.3
This object indicates the status of this entry. other(1) - this entry is currently in use but the conditions under which it will remain so are different from each of the following values. invalid(2) - writing this value to the object, and then the corresponding entry will be removed from the table. valid(3) - this entry is reside in the table.
OBJECT-TYPE    
  INTEGER other(1), invalid(2), valid(3)  

swL3RouteRedistriTable 1.3.6.1.4.1.2272.1.201.1.3.5
Route redistribution allows routers on the network. That are running different routing protocols to exchange routing information. This is accomplished by comparing the routes stored in the vairous routers routing tables and assinging appropriate metrics. This information is then exchanged among the various routers according to the individual routers current routing protocol.
OBJECT-TYPE    
  SEQUENCE OF  
    SwL3RouteRedistriEntry

swL3RouteRedistriEntry 1.3.6.1.4.1.2272.1.201.1.3.5.1
A list of information display the route redistribution table.
OBJECT-TYPE    
  SwL3RouteRedistriEntry  

swL3RouteRedistriSrcProtocol 1.3.6.1.4.1.2272.1.201.1.3.5.1.1
Allows the selection of the protocol of the source device.
OBJECT-TYPE    
  INTEGER other(1), rip(2), ospf(3), static(4), local(5)  

swL3RouteRedistriDstProtocol 1.3.6.1.4.1.2272.1.201.1.3.5.1.2
Allows the selection of the protocol of the destination device.
OBJECT-TYPE    
  INTEGER other(1), rip(2), ospf(3)  

swL3RouteRedistriType 1.3.6.1.4.1.2272.1.201.1.3.5.1.3
Allows the selection of one of the methods for calcalculating the metric value.
OBJECT-TYPE    
  INTEGER other(1), all(2), type-1(3), type-2(4), internal(5), external(6), inter-E1(7), inter-E2(8), extType1(9), extType2(10)  

swL3RouteRedistriMetric 1.3.6.1.4.1.2272.1.201.1.3.5.1.4
Allows the entry of an OSPF interface cost. This is analogous to a Hop Count in the RIP routing protocol. The value '0' indicates default value.
OBJECT-TYPE    
  INTEGER 0..16777214  

swL3RouteRedistriState 1.3.6.1.4.1.2272.1.201.1.3.5.1.5
This object indicates the status of this entry. other(1) - this entry is currently in use but the conditions under which it will remain so are different from each of the following values. invalid(2) - writing this value to the object, and then the corresponding entry will be removed from the table. valid(3) - this entry is reside in the table.
OBJECT-TYPE    
  INTEGER other(1), invalid(2), valid(3)  

swL3OspfHostTable 1.3.6.1.4.1.2272.1.201.1.3.6
The list of Hosts, and their metrics, that the router will advertise as host routes.
OBJECT-TYPE    
  SEQUENCE OF  
    SwL3OspfHostEntry

swL3OspfHostEntry 1.3.6.1.4.1.2272.1.201.1.3.6.1
A metric to be advertised, for a given type of service, when a given host is reachable.
OBJECT-TYPE    
  SwL3OspfHostEntry  

swL3OspfHostIpAddress 1.3.6.1.4.1.2272.1.201.1.3.6.1.1
The IP Address of the Host.
OBJECT-TYPE    
  IpAddress  

swL3OspfHostTOS 1.3.6.1.4.1.2272.1.201.1.3.6.1.2
The Type of Service of the route being configured.
OBJECT-TYPE    
  TOSType  

swL3OspfHostMetric 1.3.6.1.4.1.2272.1.201.1.3.6.1.3
The Metric to be advertised.
OBJECT-TYPE    
  Metric  

swL3OspfHostStatus 1.3.6.1.4.1.2272.1.201.1.3.6.1.4
This variable displays the status of the entry. Setting it to 'invalid' has the effect of rendering it inoperative. The internal effect (row removal) is implementation dependent.
OBJECT-TYPE    
  RowStatus  

swL3OspfHostAreaID 1.3.6.1.4.1.2272.1.201.1.3.6.1.5
The Area the Host Entry is to be found within. By default, the area that a subsuming OSPF interface is in, or 0.0.0.0
OBJECT-TYPE    
  AreaID  

swL3VrrpMgmt 1.3.6.1.4.1.2272.1.201.1.3.7
OBJECT IDENTIFIER    

swL3VrrpOperTable 1.3.6.1.4.1.2272.1.201.1.3.7.1
Operations table for a VRRP router which consists of a sequence (i.e., one or more conceptual rows) of 'swL3VrrpOperEntry' items.
OBJECT-TYPE    
  SEQUENCE OF  
    SwL3VrrpOperEntry

swL3VrrpOperEntry 1.3.6.1.4.1.2272.1.201.1.3.7.1.1
An entry in the swL3VrrpOperTable containing the operational characteristics of a virtual router. On a VRRP router, a given virtual router is identified by a combination of the IF index and VRID.
OBJECT-TYPE    
  SwL3VrrpOperEntry  

swL3VrrpOperVrId 1.3.6.1.4.1.2272.1.201.1.3.7.1.1.1
This object contains the Virtual Router Identifier (VRID).
OBJECT-TYPE    
  INTEGER 1..255  

swL3VrrpOperCriticalIpAddr 1.3.6.1.4.1.2272.1.201.1.3.7.1.1.2
To make sure the ip interface connected by this virtual router is alive or not.
OBJECT-TYPE    
  IpAddress  

swL3VrrpOperCriticalIpState 1.3.6.1.4.1.2272.1.201.1.3.7.1.1.3
To enable or disable the feature of critical IP.
OBJECT-TYPE    
  INTEGER other(1), disabled(2), enabled(3)  

swL3VrrpOperHoldDownTimer 1.3.6.1.4.1.2272.1.201.1.3.7.1.1.4
When VRRP is started, it need to spend this period of time to let the routing would be leared as well. The unit of this object is second.
OBJECT-TYPE    
  INTEGER 0..21600  

swL3RoutePrefTable 1.3.6.1.4.1.2272.1.201.1.3.8
IP Route Pref table.
OBJECT-TYPE    
  SEQUENCE OF  
    SwL3RoutePrefEntry

swL3RoutePrefEntry 1.3.6.1.4.1.2272.1.201.1.3.8.1
An entry of Ip Route Pref Table.
OBJECT-TYPE    
  SwL3RoutePrefEntry  

swL3RoutePrefProtocol 1.3.6.1.4.1.2272.1.201.1.3.8.1.1
Protocol
OBJECT-TYPE    
  INTEGER isis(1), rip(2), ospfIntra(3), static(4), local(5), bgp(6), staticLow(7), ospfInter(8), ospfExternal(9), ospfExternal1(10), ospfExternal2(11), ospfNssa1(12), ospfNssa2(13)  

swL3RoutePrefValue 1.3.6.1.4.1.2272.1.201.1.3.8.1.2
This value is a preference value for the given protocol.
OBJECT-TYPE    
  INTEGER 0..999  

swL3DvmrpInterfaceTable 1.3.6.1.4.1.2272.1.201.1.3.9
The (conceptual) table listing the router's multicast- capable interfaces.
OBJECT-TYPE    
  SEQUENCE OF  
    SwL3DvmrpInterfaceEntry

swL3DvmrpInterfaceEntry 1.3.6.1.4.1.2272.1.201.1.3.9.1
An entry (conceptual row) in the swL3DvmrpInterfaceTable.
OBJECT-TYPE    
  SwL3DvmrpInterfaceEntry  

swL3DvmrpInterfaceIfIndex 1.3.6.1.4.1.2272.1.201.1.3.9.1.1
The ifIndex value of the interface for which DVMRP is enabled.
OBJECT-TYPE    
  INTEGER 0..65535  

swL3DvmrpInterfaceNeighborTimeout 1.3.6.1.4.1.2272.1.201.1.3.9.1.2
The time period for DVMRP will hold Neithbor Router reports before issuing poison route messages. The unit is second.
OBJECT-TYPE    
  INTEGER 1..65535  

swL3DvmrpInterfaceProbe 1.3.6.1.4.1.2272.1.201.1.3.9.1.3
DVMRP defines an extension to IGMP that allows routers to query other routers to determine if a multicast group is present on an given router subnetwork or not. This is referred to as a 'probe'. The unit is second.
OBJECT-TYPE    
  INTEGER 1..65535