SWL2MGMT-MIB

File: SWL2MGMT-MIB.mib (178223 bytes)

Imported modules

SNMPv2-SMI SNMPv2-TC SWPRIMGMT-MIB
RFC1213-MIB RFC-1215

Imported symbols

Counter32 Counter64 TimeTicks
NOTIFICATION-TYPE MODULE-IDENTITY OBJECT-TYPE
IpAddress Unsigned32 Gauge32
MacAddress RowStatus TruthValue
privateMgmt DisplayString TRAP-TYPE

Defined Types

PortList  
OCTET STRING Size(0..127)    

VlanIndex  
Unsigned32    

SwL2PortInfoEntry  
SEQUENCE    
  swL2PortInfoPortIndex INTEGER
  swL2PortInfoUnitIndex INTEGER
  swL2PortInfoType INTEGER
  swL2PortInfoLinkStatus INTEGER
  swL2PortInfoNwayStatus INTEGER

SwL2PortCtrlEntry  
SEQUENCE    
  swL2PortCtrlPortIndex INTEGER
  swL2PortCtrlUnitIndex INTEGER
  swL2PortCtrlAdminState INTEGER
  swL2PortCtrlNwayState INTEGER
  swL2PortCtrlFlowCtrlState INTEGER
  swL2PortCtrlAddressLearningState INTEGER

SwL2PortUtilEntry  
SEQUENCE    
  swL2PortUtilPortIndex INTEGER
  swL2PortUtilTxSec Gauge32
  swL2PortUtilRxSec Gauge32
  swL2PortUtilUtilization INTEGER

SwL2FilterAddrCtrlEntry  
SEQUENCE    
  swL2FilterAddrMacIndex MacAddress
  swL2FilterAddrState INTEGER

SwL2StaticVlanEntry  
SEQUENCE    
  swL2StaticVlanIndex INTEGER
  swL2StaticVlanName DisplayString
  swL2StaticVlanType INTEGER
  swL2StaticVlanProtocolId INTEGER
  swL2StaticVlanIpSubnetAddr IpAddress
  swL2StaticVlanIpSubnetMask IpAddress
  swL2StaticVlanUserDefinedPid OCTET STRING
  swL2StaticVlanEncap INTEGER
  swL2StaticVlanUserPriority INTEGER
  swL2StaticVlanEgressPorts PortList
  swL2StaticVlanUntaggedPorts PortList
  swL2StaticVlanStatus RowStatus
  swL2StaticVlanIpSubnetArpClassId INTEGER

SwL2VlanPortEntry  
SEQUENCE    
  swL2VlanPortIndex INTEGER
  swL2VlanPortPvid INTEGER
  swL2VlanPortIngressChecking INTEGER

SwL2TrunkCtrlEntry  
SEQUENCE    
  swL2TrunkIndex INTEGER
  swL2TrunkName DisplayString
  swL2TrunkMasterPort INTEGER
  swL2TrunkMember PortList
  swL2TrunkFloodingPort INTEGER
  swL2TrunkState INTEGER
  swL2TrunkBPDU8600InterState INTEGER

SwL2IGMPCtrlEntry  
SEQUENCE    
  swL2IGMPCtrlVid INTEGER
  swL2IGMPQueryInterval INTEGER
  swL2IGMPMaxResponseTime INTEGER
  swL2IGMPRobustness INTEGER
  swL2IGMPLastMemberQueryInterval INTEGER
  swL2IGMPHostTimeout INTEGER
  swL2IGMPRouteTimeout INTEGER
  swL2IGMPLeaveTimer INTEGER
  swL2IGMPQueryState INTEGER
  swL2IGMPCurrentState INTEGER
  swL2IGMPCtrlState INTEGER

SwL2IGMPQueryInfoEntry  
SEQUENCE    
  swL2IGMPInfoVid INTEGER
  swL2IGMPInfoQueryCount INTEGER
  swL2IGMPInfoTxQueryCount INTEGER

SwL2IGMPGroupEntry  
SEQUENCE    
  swL2IGMPVid INTEGER
  swL2IGMPGroupIpAddr IpAddress
  swL2IGMPMacAddr MacAddress
  swL2IGMPPortMap PortList
  swL2IGMPIpGroupReportCount INTEGER

SwL2IGMPForwardEntry  
SEQUENCE    
  swL2IGMPForwardVid INTEGER
  swL2IGMPForwardGroupIpAddr IpAddress
  swL2IGMPForwardPortMap PortList

SwL2IGMPRPEntry  
SEQUENCE    
  swL2IGMPRPVid INTEGER
  swL2IGMPRPStaticRouterPort PortList
  swL2IGMPRPDynamicRouterPort PortList

SwL2IGMPGroupPortEntry  
SEQUENCE    
  swL2IGMPPortMember INTEGER
  swL2IGMPPortAgingTime INTEGER

SwL2TrafficCtrlEntry  
SEQUENCE    
  swL2TrafficCtrlGroupIndex INTEGER
  swL2TrafficCtrlUnitIndex INTEGER
  swL2TrafficCtrlBMStormthreshold INTEGER
  swL2TrafficCtrlBcastStormCtrl INTEGER
  swL2TrafficCtrlMcastStormCtrl INTEGER
  swL2TrafficCtrlDlfStormCtrl INTEGER

SwL2QosSchedulingEntry  
SEQUENCE    
  swL2QosSchedulingClassId INTEGER
  swL2QosSchedulingMaxPkts INTEGER
  swL2QosSchedulingMaxLatency INTEGER

SwL2QosPriorityEntry  
SEQUENCE    
  swL2QosPriorityType INTEGER
  swL2QosPriorityValue OCTET STRING
  swL2QosPriorityPriority INTEGER
  swL2QosPriorityPriorityState INTEGER
  swL2QosPriorityReplaceDscp INTEGER
  swL2QosPriorityReplaceDscpState INTEGER
  swL2QosPriorityReplacePriority INTEGER
  swL2QosPriorityState INTEGER

SwL2StormCtrlEntry  
SEQUENCE    
  swL2StormCtrlPortIndex INTEGER
  swL2StormCtrlBcastStormCtrl INTEGER
  swL2StormCtrlMcastStormCtrl INTEGER
  swL2StormCtrlBMStormThreshold INTEGER

SwL2CpuRateLimitEntry  
SEQUENCE    
  swL2CpuRateLimitPortIndex INTEGER
  swL2CpuRateLimitState INTEGER
  swL2CpuRateLimitBcastThreshold INTEGER
  swL2CpuRateLimitMcastThreshold INTEGER

SwL2ACLQosFlowClassifierEntry  
SEQUENCE    
  swL2ACLQosFlowClassifierTemplateId INTEGER
  swL2ACLQosFlowClassifierCurrentMode INTEGER
  swL2ACLQosFlowClassifierSecuritySrcMask IpAddress
  swL2ACLQosFlowClassifierQosFlavor INTEGER
  swL2ACLQosFlowClassifierL4SwitchTCPDstIp INTEGER
  swL2ACLQosFlowClassifierL4SwitchTCPSrcIp INTEGER
  swL2ACLQosFlowClassifierL4SwitchTCPTos INTEGER
  swL2ACLQosFlowClassifierL4SwitchTCPDstPort INTEGER
  swL2ACLQosFlowClassifierL4SwitchTCPSrcPort INTEGER
  swL2ACLQosFlowClassifierL4SwitchTCPFlags INTEGER
  swL2ACLQosFlowClassifierL4SwitchUDPDstIp INTEGER
  swL2ACLQosFlowClassifierL4SwitchUDPSrcIp INTEGER
  swL2ACLQosFlowClassifierL4SwitchUDPTos INTEGER
  swL2ACLQosFlowClassifierL4SwitchUDPDstPort INTEGER
  swL2ACLQosFlowClassifierL4SwitchUDPSrcPort INTEGER
  swL2ACLQosFlowClassifierL4SwitchOtherDstIp INTEGER
  swL2ACLQosFlowClassifierL4SwitchOtherSrcIp INTEGER
  swL2ACLQosFlowClassifierL4SwitchOtherTos INTEGER
  swL2ACLQosFlowClassifierL4SwitchOtherL4Protocol INTEGER
  swL2ACLQosFlowClassifierL4SwitchOtherICMPMessage INTEGER
  swL2ACLQosFlowClassifierL4SwitchOtherIGMPType INTEGER
  swL2ACLQosFlowClassifierActiveRuleNumber INTEGER
  swL2ACLQosFlowClassifierSecurityDstMask IpAddress

SwL2ACLQosFlowClassifierVlanEntry  
SEQUENCE    
  swL2ACLQosFlowClassifierVlanTemplateId INTEGER
  swL2ACLQosFlowClassifierVlanVlanName DisplayString
  swL2ACLQosFlowClassifierVlanState INTEGER

SwL2ACLQosTemplateRuleEntry  
SEQUENCE    
  swL2ACLQosTemplateRuleTemplateId INTEGER
  swL2ACLQosTemplateRuleIndex INTEGER
  swL2ACLQosTemplateRuleMode INTEGER
  swL2ACLQosTemplateRuleSecuritySrcIp IpAddress
  swL2ACLQosTemplateRuleQosFlavor INTEGER
  swL2ACLQosTemplateRuleQosValue OCTET STRING
  swL2ACLQosTemplateRuleQosPriority INTEGER
  swL2ACLQosTemplateRuleQosDscp INTEGER
  swL2ACLQosTemplateRuleL4SwitchSessionType INTEGER
  swL2ACLQosTemplateRuleL4SwitchSessionTCPDstIp IpAddress
  swL2ACLQosTemplateRuleL4SwitchSessionTCPSrcIp IpAddress
  swL2ACLQosTemplateRuleL4SwitchSessionTCPTos OCTET STRING
  swL2ACLQosTemplateRuleL4SwitchSessionTCPDstPort INTEGER
  swL2ACLQosTemplateRuleL4SwitchSessionTCPSrcPort INTEGER
  swL2ACLQosTemplateRuleL4SwitchSessionTCPFlags INTEGER
  swL2ACLQosTemplateRuleL4SwitchSessionUDPDstIp IpAddress
  swL2ACLQosTemplateRuleL4SwitchSessionUDPSrcIp IpAddress
  swL2ACLQosTemplateRuleL4SwitchSessionUDPTos OCTET STRING
  swL2ACLQosTemplateRuleL4SwitchSessionUDPDstPort INTEGER
  swL2ACLQosTemplateRuleL4SwitchSessionUDPSrcPort INTEGER
  swL2ACLQosTemplateRuleL4SwitchSessionOtherDstIp IpAddress
  swL2ACLQosTemplateRuleL4SwitchSessionOtherSrcIp IpAddress
  swL2ACLQosTemplateRuleL4SwitchSessionOtherTos OCTET STRING
  swL2ACLQosTemplateRuleL4SwitchSessionOtherL4Protocol INTEGER
  swL2ACLQosTemplateRuleL4SwitchSessionOtherICMPType OCTET STRING
  swL2ACLQosTemplateRuleL4SwitchSessionOtherICMPCode OCTET STRING
  swL2ACLQosTemplateRuleL4SwitchSessionOtherIGMPType INTEGER
  swL2ACLQosTemplateRuleL4SwitchActionType INTEGER
  swL2ACLQosTemplateRuleL4SwitchActionForwardPriorityState INTEGER
  swL2ACLQosTemplateRuleL4SwitchActionForwardPriority INTEGER
  swL2ACLQosTemplateRuleL4SwitchActionForwardDscp INTEGER
  swL2ACLQosTemplateRuleL4SwitchActionRedirectIp IpAddress
  swL2ACLQosTemplateRuleL4SwitchActionRedirectDropUnreachable INTEGER
  swL2ACLQosTemplateRuleState INTEGER
  swL2ACLQosTemplateRuleL4SwitchSessionTCPFlagsAll BITS
  swL2ACLQosTemplateRuleSecurityDstIp IpAddress

SwL2ACLQosDestinationIpFilterEntry  
SEQUENCE    
  swL2ACLQosDestinationIpFilterIndex INTEGER
  swL2ACLQosDestinationIpFilterIpAddr IpAddress
  swL2ACLQosDestinationIpFilterState INTEGER

SwL2ACLQosFDBFilterEntry  
SEQUENCE    
  swL2ACLQosFDBFilterIndex INTEGER
  swL2ACLQosFDBFilterVlanName DisplayString
  swL2ACLQosFDBFilterMacAddress MacAddress
  swL2ACLQosFDBFilterState INTEGER

SwL2ACLQosSchedulingEntry  
SEQUENCE    
  swL2ACLQosSchedulingPortIndex INTEGER
  swL2ACLQosSchedulingClassId INTEGER
  swL2ACLQosSchedulingWRRValue INTEGER

SwL2ACLQosMacPriorityEntry  
SEQUENCE    
  swL2ACLQosMacPriorityIndex INTEGER
  swL2ACLQosMacPriorityVlanName DisplayString
  swL2ACLQosMacPriorityDstMacAddress MacAddress
  swL2ACLQosMacPriorityPriorityValue INTEGER
  swL2ACLQosMacPriorityState INTEGER

Defined Values

swL2MgmtMIB 1.3.6.1.4.1.2272.1.201.1.2
The Structure of Layer 2 Network Management Information for the proprietary enterprise.
MODULE-IDENTITY    

swL2DevMgmt 1.3.6.1.4.1.2272.1.201.1.2.1
OBJECT IDENTIFIER    

swL2UnitMgmt 1.3.6.1.4.1.2272.1.201.1.2.2
OBJECT IDENTIFIER    

swL2ModuleMgmt 1.3.6.1.4.1.2272.1.201.1.2.3
OBJECT IDENTIFIER    

swL2PortMgmt 1.3.6.1.4.1.2272.1.201.1.2.4
OBJECT IDENTIFIER    

swL2FilterMgmt 1.3.6.1.4.1.2272.1.201.1.2.6
OBJECT IDENTIFIER    

swL2VlanMgmt 1.3.6.1.4.1.2272.1.201.1.2.7
OBJECT IDENTIFIER    

swL2TrunkMgmt 1.3.6.1.4.1.2272.1.201.1.2.8
OBJECT IDENTIFIER    

swL2MirrorMgmt 1.3.6.1.4.1.2272.1.201.1.2.9
OBJECT IDENTIFIER    

swL2IGMPMgmt 1.3.6.1.4.1.2272.1.201.1.2.10
OBJECT IDENTIFIER    

swL2TrafficMgmt 1.3.6.1.4.1.2272.1.201.1.2.12
OBJECT IDENTIFIER    

swL2QosMgmt 1.3.6.1.4.1.2272.1.201.1.2.13
OBJECT IDENTIFIER    

swL2MgmtMIBTraps 1.3.6.1.4.1.2272.1.201.1.2.14
OBJECT IDENTIFIER    

swL2StormCtrlMgmt 1.3.6.1.4.1.2272.1.201.1.2.15
OBJECT IDENTIFIER    

swL2ACLQosMgmt 1.3.6.1.4.1.2272.1.201.1.2.16
OBJECT IDENTIFIER    

swL2MgmtPortMgmt 1.3.6.1.4.1.2272.1.201.1.2.17
OBJECT IDENTIFIER    

swL2DevInfo 1.3.6.1.4.1.2272.1.201.1.2.1.1
OBJECT IDENTIFIER    

swDevInfoSystemUpTime 1.3.6.1.4.1.2272.1.201.1.2.1.1.1
The value of sysUpTime at the time the switch entered its current operational state. If the current state was entered prior to the last re-initialization, then this object contains a zero value. This value is in units of seconds.
Status: current Access: read-only
OBJECT-TYPE    
  TimeTicks  

swDevInfoTotalNumOfPort 1.3.6.1.4.1.2272.1.201.1.2.1.1.2
The number of ports within this switch. This value is the sum of the ports within this switch.
Status: current Access: read-only
OBJECT-TYPE    
  INTEGER 0..65535  

swDevInfoNumOfPortInUse 1.3.6.1.4.1.2272.1.201.1.2.1.1.3
The number of ports in this switch connected to the segment or the end stations.
Status: current Access: read-only
OBJECT-TYPE    
  INTEGER 0..65535  

swDevInfoConsoleInUse 1.3.6.1.4.1.2272.1.201.1.2.1.1.4
This usage indication of console system.
Status: current Access: read-only
OBJECT-TYPE    
  INTEGER other(1), in-use(2), not-in-use(3)  

swDevInfoFrontPanelLedStatus 1.3.6.1.4.1.2272.1.201.1.2.1.1.5
This object is a set of system LED indications. The first three octets is defined as system LED. The first LED is primary power LED. The second LED is redundant power LED. The third LED is console LED. The other octets following the second octets are the logical port LED (following dot1dBasePort ordering). Every two bytes are presented to a port. The first byte is presentd to the Link/Activity LED. The second byte is presented to the Speed LED. Link/Activity LED : The most significant bit is used for blink/solid: 8 = The LED blinks. The second significant bit is used for link status: 1 = link fail. 2 = link pass. Speed LED : 01 = 10Mbps. 02 = 100Mbps. 03 = 1000Mbps. The four remaining bits are currently unused and must be 0.
Status: current Access: read-only
OBJECT-TYPE    
  OCTET STRING Size(0..324)  

swL2DevCtrlUpDownloadState 1.3.6.1.4.1.2272.1.201.1.2.1.1.6
status of upload/download control. If the value is 'other', means never firmware updated since device started up.
Status: current Access: read-only
OBJECT-TYPE    
  INTEGER other(1), in-process(2), invalid-file(3), violation(4), file-not-found(5), disk-full(6), complete(7), time-out(8), tftp-establish-fail(9)  

swDevInfoSaveCfg 1.3.6.1.4.1.2272.1.201.1.2.1.1.7
This object indicates the status of the device configuration. other(1) - this entry is currently in use but the conditions under which it will remain so are different from each of the following values. proceeding(2) - the device configuration is saving into the NV-RAM. ready(3) - the device configuration has been ready to save into NV-RAM. failed(4) - The processing of saving device configuration is failed.
Status: current Access: read-only
OBJECT-TYPE    
  INTEGER other(1), proceeding(2), ready(3), failed(4)  

swL2DevCtrl 1.3.6.1.4.1.2272.1.201.1.2.1.2
OBJECT IDENTIFIER    

swL2DevCtrlStpState 1.3.6.1.4.1.2272.1.201.1.2.1.2.1
This object can be enabled or disabled spanning tree algorithm during runtime of the system.
Status: current Access: read-write
OBJECT-TYPE    
  INTEGER other(1), disabled(2), enabled(3)  

swL2DevCtrlIGMPSnooping 1.3.6.1.4.1.2272.1.201.1.2.1.2.2
This object indicates layer 2 Internet Group Management Protocol (IGMP) capture function is enabled or disabled.
Status: current Access: read-write
OBJECT-TYPE    
  INTEGER other(1), disabled(2), enabled(3)  

swL2DevCtrlRmonState 1.3.6.1.4.1.2272.1.201.1.2.1.2.3
This object can be enabled or disabled RMON.
Status: current Access: read-write
OBJECT-TYPE    
  INTEGER other(1), disabled(2), enabled(3)  

swL2DevCtrlUpDownloadImageFileName 1.3.6.1.4.1.2272.1.201.1.2.1.2.4
The name of the image file to be uploaded/Downloaded from the device to TFTP server when enabling image upload/download function (by writing swL2DevCtrlUpDownloadImage).
Status: current Access: read-write
OBJECT-TYPE    
  DisplayString Size(0..64)  

swL2DevCtrlUpDownloadImageSourceAddr 1.3.6.1.4.1.2272.1.201.1.2.1.2.5
The ip address where been uploaded/Downloaded image file.
Status: current Access: read-write
OBJECT-TYPE    
  IpAddress  

swL2DevCtrlUpDownloadImage 1.3.6.1.4.1.2272.1.201.1.2.1.2.6
Image file upload/download control. After setting, it will immediately invoke image upload/download function. While retrieving the value of this object, it always returns 'other' normally.
Status: current Access: read-write
OBJECT-TYPE    
  INTEGER other(1), upload(2), download(3)  

swL2DevCtrlSaveCfg 1.3.6.1.4.1.2272.1.201.1.2.1.2.7
As the object is set to active, the current device configuration is save into to NV-RAM.If set to normal, do nothing.
Status: current Access: read-write
OBJECT-TYPE    
  INTEGER normal(1), active(2)  

swL2DevCtrlCleanAllStatisticCounter 1.3.6.1.4.1.2272.1.201.1.2.1.2.8
As the object is set to active, all the statistic counters will be cleared. If set to normal, do nothing.
Status: current Access: read-write
OBJECT-TYPE    
  INTEGER normal(1), active(2)  

swL2DevCtrlStpForwardBPDU 1.3.6.1.4.1.2272.1.201.1.2.1.2.9
This object allow the forwarding of STP BPDU packets from other network device or not when STP is disabled on the device.
Status: current Access: read-write
OBJECT-TYPE    
  INTEGER other(1), disabled(2), enabled(3)  

swL2DevAlarm 1.3.6.1.4.1.2272.1.201.1.2.1.3
OBJECT IDENTIFIER    

swL2DevAlarmNewRoot 1.3.6.1.4.1.2272.1.201.1.2.1.3.1
When the device has become the new root of the Spanning Tree, this object decide whether to send a new root trap.
Status: current Access: read-write
OBJECT-TYPE    
  INTEGER other(1), disabled(2), enabled(3)  

swL2DevAlarmTopologyChange 1.3.6.1.4.1.2272.1.201.1.2.1.3.2
This object determine to send a trap or not when the switch topology was changed. If the object is enabled(3), the topologyChange trap is sent by the device when any of its configured ports transitions from the Learning state to the Forwarding state, or from the Forwarding state to the Blocking state. For the same port tranition, the device doesn't send the trap if this object value is disabled or other.
Status: current Access: read-write
OBJECT-TYPE    
  INTEGER other(1), disabled(2), enabled(3)  

swL2DevAlarmLinkChange 1.3.6.1.4.1.2272.1.201.1.2.1.3.3
This object determine to send a trap or not when the link was changed. If the object is enabled(3), the Link Change trap is sent by the device when any of its ports link change. The device doesn't send the trap if this object value is disabled or other.
Status: current Access: read-write
OBJECT-TYPE    
  INTEGER other(1), disabled(2), enabled(3)  

swL2UnitCtrl 1.3.6.1.4.1.2272.1.201.1.2.2.1
OBJECT IDENTIFIER    

swL2PortInfoTable 1.3.6.1.4.1.2272.1.201.1.2.4.1
A table that contains information about every port.
Status: current Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    SwL2PortInfoEntry

swL2PortInfoEntry 1.3.6.1.4.1.2272.1.201.1.2.4.1.1
A list of information for each port of the device.
Status: current Access: not-accessible
OBJECT-TYPE    
  SwL2PortInfoEntry  

swL2PortInfoPortIndex 1.3.6.1.4.1.2272.1.201.1.2.4.1.1.1
This object indicates the module's port number.(1..Max port number in the module)
Status: current Access: read-only
OBJECT-TYPE    
  INTEGER 0..65535  

swL2PortInfoUnitIndex 1.3.6.1.4.1.2272.1.201.1.2.4.1.1.2
Indicates ID of the unit in the device
Status: current Access: read-only
OBJECT-TYPE    
  INTEGER 0..65535  

swL2PortInfoType 1.3.6.1.4.1.2272.1.201.1.2.4.1.1.3
This object indicates the connector type of this port.
Status: current Access: read-only
OBJECT-TYPE    
  INTEGER other(1), portType-100Base-TX(2), portType-100Base-FX(3), portType-100Base-FL(4), portType-1000Base-T(5), portType-1000Base-SX(6), portType-1000Base-LX(7), portType-1000Base-GBIC-SX(8), portType-1000Base-GBIC-LX(9), portType-1000Base-GBIC-CWDM(10), portType-1000Base-GBIC-XD(11), portType-1000Base-GBIC-ZX(12), portType-1000Base-GBIC-COPPER(13), portType-1000Base-GBIC-OTHER(14)  

swL2PortInfoLinkStatus 1.3.6.1.4.1.2272.1.201.1.2.4.1.1.4
This object indicates the port link status.
Status: current Access: read-only
OBJECT-TYPE    
  INTEGER other(1), link-pass(2), link-fail(3)  

swL2PortInfoNwayStatus 1.3.6.1.4.1.2272.1.201.1.2.4.1.1.5
This object indicates the port speed and duplex mode.
Status: current Access: read-only
OBJECT-TYPE    
  INTEGER other(1), auto(2), half-10Mbps(3), full-10Mbps(4), half-100Mbps(5), full-100Mbps(6), half-1Gigabps(7), full-1Gigabps(8)  

swL2PortCtrlTable 1.3.6.1.4.1.2272.1.201.1.2.4.2
A table that contains control information about every port.
Status: current Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    SwL2PortCtrlEntry

swL2PortCtrlEntry 1.3.6.1.4.1.2272.1.201.1.2.4.2.1
A list of control information for each port of the device.
Status: current Access: not-accessible
OBJECT-TYPE    
  SwL2PortCtrlEntry  

swL2PortCtrlPortIndex 1.3.6.1.4.1.2272.1.201.1.2.4.2.1.1
This object indicates the module's port number.(1..Max port number in the module)
Status: current Access: read-only
OBJECT-TYPE    
  INTEGER 0..65535  

swL2PortCtrlUnitIndex 1.3.6.1.4.1.2272.1.201.1.2.4.2.1.2
Indicates ID of the unit in the device
Status: current Access: read-only
OBJECT-TYPE    
  INTEGER 0..65535  

swL2PortCtrlAdminState 1.3.6.1.4.1.2272.1.201.1.2.4.2.1.3
This object decide the port enabled or disabled.
Status: current Access: read-write
OBJECT-TYPE    
  INTEGER other(1), disabled(2), enabled(3)  

swL2PortCtrlNwayState 1.3.6.1.4.1.2272.1.201.1.2.4.2.1.4
Chose the port speed, duplex mode, and N-Way function mode.
Status: current Access: read-write
OBJECT-TYPE    
  INTEGER other(1), nway-enabled(2), nway-disabled-10Mbps-Half(3), nway-disabled-10Mbps-Full(4), nway-disabled-100Mbps-Half(5), nway-disabled-100Mbps-Full(6), nway-disabled-1Gigabps-Full(7)  

swL2PortCtrlFlowCtrlState 1.3.6.1.4.1.2272.1.201.1.2.4.2.1.5
The flow control mechanism is different between full duplex mode and half duplex mode. For half duplex mode, the jamming signal is asserted. For full duplex mode, IEEE 802.3x flow control function sends PAUSE frames and receives PAUSE frames.
Status: current Access: read-write
OBJECT-TYPE    
  INTEGER other(1), disabled(2), enabled(3)  

swL2PortCtrlAddressLearningState 1.3.6.1.4.1.2272.1.201.1.2.4.2.1.6
This object decide the address learning state on this port is enabled or disabled.
Status: current Access: read-write
OBJECT-TYPE    
  INTEGER other(1), disabled(2), enabled(3)  

swL2PortUtilTable 1.3.6.1.4.1.2272.1.201.1.2.4.3
A table that contains information of utilization about every port.
Status: current Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    SwL2PortUtilEntry

swL2PortUtilEntry 1.3.6.1.4.1.2272.1.201.1.2.4.3.1
A list of information of utilization for each port of the device.
Status: current Access: not-accessible
OBJECT-TYPE    
  SwL2PortUtilEntry  

swL2PortUtilPortIndex 1.3.6.1.4.1.2272.1.201.1.2.4.3.1.1
This object indicates the module's port number.(1..Max port number in the module)
Status: current Access: read-only
OBJECT-TYPE    
  INTEGER 0..65535  

swL2PortUtilTxSec 1.3.6.1.4.1.2272.1.201.1.2.4.3.1.2
Indicates how many packets transmitted per second.
Status: current Access: read-only
OBJECT-TYPE    
  Gauge32  

swL2PortUtilRxSec 1.3.6.1.4.1.2272.1.201.1.2.4.3.1.3
Indicates how many packets received per second.
Status: current Access: read-only
OBJECT-TYPE    
  Gauge32  

swL2PortUtilUtilization 1.3.6.1.4.1.2272.1.201.1.2.4.3.1.4
This object indicates the port utilization.
Status: current Access: read-only
OBJECT-TYPE    
  INTEGER 0..100  

swL2FilterAddrConfig 1.3.6.1.4.1.2272.1.201.1.2.6.1
OBJECT IDENTIFIER    

swL2FilterAddrMaxSupportedEntries 1.3.6.1.4.1.2272.1.201.1.2.6.1.1
Maximum number of entries in the MAC address filtering table (swL2FilterAddrCtrlTable).
Status: current Access: read-only
OBJECT-TYPE    
  INTEGER 0..65535  

swL2FilterAddrCurrentTotalEntries 1.3.6.1.4.1.2272.1.201.1.2.6.1.2
Current applied number of entries in the MAC address filtering table.
Status: current Access: read-only
OBJECT-TYPE    
  INTEGER 0..65535  

swL2FilterAddrCtrlTable 1.3.6.1.4.1.2272.1.201.1.2.6.1.3
This table defines information for the device to filter packets with specific MAC address (either as the DA and/or as the SA). The MAC address can be a unicast address or a multicast address. This table has higher priority than both static FDB table and IGMP table. It means that if a MAC address appears on this table also appears on the static FDB table, the device will use the information provide by this table to process the packet.
Status: current Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    SwL2FilterAddrCtrlEntry

swL2FilterAddrCtrlEntry 1.3.6.1.4.1.2272.1.201.1.2.6.1.3.1
A list of information about a specific unicast/multicast MAC address for which the switch has filtering information.
Status: current Access: not-accessible
OBJECT-TYPE    
  SwL2FilterAddrCtrlEntry  

swL2FilterAddrMacIndex 1.3.6.1.4.1.2272.1.201.1.2.6.1.3.1.1
This object indicates a unicast/multicast MAC address for which the switch has filtering information. But if the swL2FilterAddrState = src-addr then the object can not be a multicast MAC address.
Status: current Access: read-only
OBJECT-TYPE    
  MacAddress  

swL2FilterAddrState 1.3.6.1.4.1.2272.1.201.1.2.6.1.3.1.2
This object indicates the status of this entry. other(1) - this entry is currently in use but the conditions under which it will remain so are different from each of the following values. dst-addr(2) - recieved frames's destination address are currently used to be filtered as it meets with the MAC address entry of the table. src-addr(3) - recieved frames's source address are currently used to be filtered as it meets with the MAC address entry of the table. dst-src-addr(4) - recieved frames's destination address or source address are currently used to be filtered as it meets with the MAC address entry of the table. invalid(5) - writing this value to the object, and then the corresponding entry will be removed from the table.
Status: current Access: read-write
OBJECT-TYPE    
  INTEGER other(1), dst-addr(2), src-addr(3), dst-src-addr(4), invalid(5)  

swL2StaticVlanTable 1.3.6.1.4.1.2272.1.201.1.2.7.1
A table containing static configuration information for each VLAN configured into the device by (local or network) management.
Status: current Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    SwL2StaticVlanEntry

swL2StaticVlanEntry 1.3.6.1.4.1.2272.1.201.1.2.7.1.1
Static information for a VLAN configured into the device by (local or network) management.
Status: current Access: not-accessible
OBJECT-TYPE    
  SwL2StaticVlanEntry  

swL2StaticVlanIndex 1.3.6.1.4.1.2272.1.201.1.2.7.1.1.1
A value that uniquely identifies the Virtual LAN associated with this entry.
Status: current Access: read-only
OBJECT-TYPE    
  INTEGER 1..4094  

swL2StaticVlanName 1.3.6.1.4.1.2272.1.201.1.2.7.1.1.2
An administratively-assigned name for this VLAN.
Status: current Access: read-write
OBJECT-TYPE    
  DisplayString Size(1..32)  

swL2StaticVlanType 1.3.6.1.4.1.2272.1.201.1.2.7.1.1.3
The type of VLAN, distinguished according to the policy used to define its port membership.
Status: current Access: read-write
OBJECT-TYPE    
  INTEGER byport(1), byIpSubnet(2), byProtocolId(3)  

swL2StaticVlanProtocolId 1.3.6.1.4.1.2272.1.201.1.2.7.1.1.4
The protocol identifier of this VLAN. This value is meaningful only if swL2StaticVlanType is equal to byProtocolId(3). For other VLAN types it should have the value none(0).
Status: current Access: read-write
OBJECT-TYPE    
  INTEGER none(0), ipEther2(1), rarpEther2(2), ipx802dot3(3), ipx802dot2(4), ipxSnap(5), ipxEther2(6), apltkEther2Snap(7), decEther2(8), decOtherEther2(9), sna802dot2(10), snaEther2(11), netBios(12), xnsEther2(13), vinesEther2(14), ipv6Ether2(15), userDefined(16), arpEther2(17)  

swL2StaticVlanIpSubnetAddr 1.3.6.1.4.1.2272.1.201.1.2.7.1.1.5
The IP subnet address of this VLAN. This value is meaningful only if rcVlanType is equal to byIpSubnet(2). For other VLAN types it should have the value 0.0.0.0.
Status: current Access: read-write
OBJECT-TYPE    
  IpAddress  

swL2StaticVlanIpSubnetMask 1.3.6.1.4.1.2272.1.201.1.2.7.1.1.6
The IP subnet mask of this VLAN. This value is meaningful only if rcVlanType is equal to byIpSubnet(2). For other VLAN types it should have the value 0.0.0.0.
Status: current Access: read-write
OBJECT-TYPE    
  IpAddress  

swL2StaticVlanUserDefinedPid 1.3.6.1.4.1.2272.1.201.1.2.7.1.1.7
When swL2StaticVlanProtocolId is set to userDefined(16) in a protocol-based VLAN, this field represents the 16-bit user defined protocol identifier. Otherwise, this object should be zero.
Status: current Access: read-write
OBJECT-TYPE    
  OCTET STRING Size(0..2)  

swL2StaticVlanEncap 1.3.6.1.4.1.2272.1.201.1.2.7.1.1.8
This value is meaningful only if swL2StaticVlanProtocolId is set to userDefined(16). Otherwise, this object should be un-used(5). If If this set to ethernet2(2), the Detagged Frame uses Type-encapsulated 802.3 format. If this set to llc(3), the Detagged Frame contains both a DSAP and an SSAP address field in the positions. If this set to snap(4), the Detagged Frame is of the format specified by IEEE Std. 802.1H for the encoding of an IEEE 802.3 Type Field in an 802.2/SNAP header.
Status: current Access: read-write
OBJECT-TYPE    
  INTEGER all(1), ethernet2(2), llc(3), snap(4), un-used(5)  

swL2StaticVlanUserPriority 1.3.6.1.4.1.2272.1.201.1.2.7.1.1.9
User priority level. This value is meaningful only if swL2StaticVlanType is set to byIpSubnet(2) or byProtocolId(3).
Status: current Access: read-write
OBJECT-TYPE    
  INTEGER 0 | 4 | 6 | 7  

swL2StaticVlanEgressPorts 1.3.6.1.4.1.2272.1.201.1.2.7.1.1.10
The set of ports which are permanently assigned to the egress list for this VLAN by management. The default value of this object is a string of zeros of appropriate length.
Status: current Access: read-write
OBJECT-TYPE    
  PortList  

swL2StaticVlanUntaggedPorts 1.3.6.1.4.1.2272.1.201.1.2.7.1.1.11
The set of ports which should transmit egress packets for this VLAN as untagged. The default value of this object for the default VLAN is a string of appropriate length including all ports. There is no specified default for other VLANs.
Status: current Access: read-write
OBJECT-TYPE    
  PortList  

swL2StaticVlanStatus 1.3.6.1.4.1.2272.1.201.1.2.7.1.1.12
This object indicates the status of this entry.
Status: current Access: read-write
OBJECT-TYPE    
  RowStatus  

swL2StaticVlanIpSubnetArpClassId 1.3.6.1.4.1.2272.1.201.1.2.7.1.1.13
This object indicates the ARP classification ID. If the swL2StaticVlanType is not byIpSubnet(2), this value must be 0. If the swL2StaticVlanType is byIpSubnet(2), the range of this object is 1 to 4094. This object is useful when create the first IpSubnet entry, and not allow to modify.
Status: current Access: read-write
OBJECT-TYPE    
  INTEGER 0..4094  

swL2VlanPortTable 1.3.6.1.4.1.2272.1.201.1.2.7.2
A table containing per port control and status information for VLAN configuration in the device.
Status: current Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    SwL2VlanPortEntry

swL2VlanPortEntry 1.3.6.1.4.1.2272.1.201.1.2.7.2.1
Information controlling VLAN configuration for a port on the device.
Status: current Access: not-accessible
OBJECT-TYPE    
  SwL2VlanPortEntry  

swL2VlanPortIndex 1.3.6.1.4.1.2272.1.201.1.2.7.2.1.1
An unique index used to identify a particular port in the system.
Status: current Access: read-only
OBJECT-TYPE    
  INTEGER  

swL2VlanPortPvid 1.3.6.1.4.1.2272.1.201.1.2.7.2.1.2
The PVID, the VLAN ID assigned to untagged frames or Priority- Tagged frames received on this port.
Status: current Access: read-only
OBJECT-TYPE    
  INTEGER  

swL2VlanPortIngressChecking 1.3.6.1.4.1.2272.1.201.1.2.7.2.1.3
When this is enabled(3) the device will discard incoming frames for VLANs which do not include this Port in its Member set. When disabled(2), the port will accept all incoming frames.
Status: current Access: read-write
OBJECT-TYPE    
  INTEGER other(1), disabled(2), enabled(3)  

swL2TrunkMaxSupportedEntries 1.3.6.1.4.1.2272.1.201.1.2.8.1
Maximum number of entries in the trunk configuration table (swL2TrunkCtrlTable).
Status: current Access: read-only
OBJECT-TYPE    
  INTEGER 0..65535  

swL2TrunkCurrentNumEntries 1.3.6.1.4.1.2272.1.201.1.2.8.2
Current actived number of entries in the trunk configuration table.
Status: current Access: read-only
OBJECT-TYPE    
  INTEGER 0..65535  

swL2TrunkCtrlTable 1.3.6.1.4.1.2272.1.201.1.2.8.3
This table specifys which ports group a set of ports(up to 8) into a single logical link.
Status: current Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    SwL2TrunkCtrlEntry

swL2TrunkCtrlEntry 1.3.6.1.4.1.2272.1.201.1.2.8.3.1
A list of information specifies which ports group a set of ports(up to 8) into a single logical link.
Status: current Access: not-accessible
OBJECT-TYPE    
  SwL2TrunkCtrlEntry  

swL2TrunkIndex 1.3.6.1.4.1.2272.1.201.1.2.8.3.1.1
The index of logical port trunk. The trunk group number depend on the existence of unit and module.
Status: current Access: read-only
OBJECT-TYPE    
  INTEGER 0..65535  

swL2TrunkName 1.3.6.1.4.1.2272.1.201.1.2.8.3.1.2
The name of logical port trunk.
Status: current Access: read-write
OBJECT-TYPE    
  DisplayString Size(0..12)  

swL2TrunkMasterPort 1.3.6.1.4.1.2272.1.201.1.2.8.3.1.3
The object indicates the master port number of the port trunk entry. When using Port Trunk, you can not configure the other ports of the group except the master port. Their configuration must be same as the master port (e.g. speed, duplex, enabled/disabled, flow control, and so on).
Status: current Access: read-write
OBJECT-TYPE    
  INTEGER 1..65535  

swL2TrunkMember 1.3.6.1.4.1.2272.1.201.1.2.8.3.1.4
Indicate how many number of ports is included in this Trunk. The trunk port number depend on the existence of module. The maximum number of ports is 4 for one trunks.
Status: current Access: read-write
OBJECT-TYPE    
  PortList  

swL2TrunkFloodingPort 1.3.6.1.4.1.2272.1.201.1.2.8.3.1.5
The object indicates the flooding port number of the port trunk entry. The first port of the trunk is implicitly configured to be the flooding port.
Status: current Access: read-only
OBJECT-TYPE    
  INTEGER 1..65535  

swL2TrunkState 1.3.6.1.4.1.2272.1.201.1.2.8.3.1.6
This object indicates the status of this entry. other(1) - this entry is currently in use but the conditions under which it will remain so are different from each of the following values. disabled(2) - the port trunk disabled. enabled(3) - the port trunk enabled. invalid(4) - writing this value to the object, and then the corresponding entry will be removed from the table.
Status: current Access: read-write
OBJECT-TYPE    
  INTEGER other(1), disabled(2), enabled(3), invalid(4)  

swL2TrunkBPDU8600InterState 1.3.6.1.4.1.2272.1.201.1.2.8.3.1.7
This object indicates the status of this entry. other(1) - this entry is currently in use but the conditions under which it will remain so are different from each of the following values. disabled(2) - the trunk member doesn't send BPDU. enabled(3) - the trunk member can send BPDU.
Status: current Access: read-write
OBJECT-TYPE    
  INTEGER other(1), disabled(2), enabled(3)  

swL2TrunkAlgorithm 1.3.6.1.4.1.2272.1.201.1.2.8.4
This object configures to part of the packet examined by the switch when selecting the egress port for transmitting load-sharing data. This feature is only available using the address-based load-sharing algorithm.
Status: current Access: read-write
OBJECT-TYPE    
  INTEGER other(1), mac-source(2), mac-destination(3), mac-source-dest(4), ip-source(5), ip-destination(6), ip-source-dest(7)  

swL2MirrorLogicTargetPort 1.3.6.1.4.1.2272.1.201.1.2.9.1
This object indicates switch which port will sniff another port. A trunk port member cannot be configured as a target Snooping port. The port number is the sequential (logical) number which is also applied to bridge MIB, etc.
Status: current Access: read-write
OBJECT-TYPE    
  INTEGER 0..65535  

swL2MirrorPortSourceIngress 1.3.6.1.4.1.2272.1.201.1.2.9.2
The represent the ingress into the source port packet to sniffed.
Status: current Access: read-write
OBJECT-TYPE    
  PortList  

swL2MirrorPortSourceEgress 1.3.6.1.4.1.2272.1.201.1.2.9.3
The represent the egress from the source port packet to sniffed.
Status: current Access: read-write
OBJECT-TYPE    
  PortList  

swL2MirrorPortState 1.3.6.1.4.1.2272.1.201.1.2.9.4
This object indicates the port mirroring state. other(1) - this entry is currently in use but the conditions under which it will remain so are different from each of the following values. disabled(2) - writing this value to the object, and then the corresponding entry will be removed from the table. enabled(3) - this entry is reside in the table.
Status: current Access: read-write
OBJECT-TYPE    
  INTEGER other(1), disabled(2), enabled(3)  

swL2IGMPMaxSupportedVlans 1.3.6.1.4.1.2272.1.201.1.2.10.1
Maximum number of Vlans in the layer 2 IGMP control table (swL2IGMPCtrlTable).
Status: current Access: read-only
OBJECT-TYPE    
  INTEGER 0..65535  

swL2IGMPMaxIpGroupNumPerVlan 1.3.6.1.4.1.2272.1.201.1.2.10.2
Maximum number of multicast ip group per Vlan in the layer 2 IGMP information table (swL2IGMPQueryInfoTable).
Status: current Access: read-only
OBJECT-TYPE    
  INTEGER 0..65535  

swL2IGMPCtrlTable 1.3.6.1.4.1.2272.1.201.1.2.10.3
The table controls the Vlan's IGMP function. Its scale depends on current VLAN state (swL2VlanInfoStatus). If VLAN is disabled mode, there is only one entry in the table, with index 1. If VLAN is in Port-Base or 802.1q mode, the number of entries can be up to 12, with index range from 1 to 12.
Status: current Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    SwL2IGMPCtrlEntry

swL2IGMPCtrlEntry 1.3.6.1.4.1.2272.1.201.1.2.10.3.1
The entry in IGMP control table (swL2IGMPCtrlTable). The entry is effective only when IGMP capture switch (swL2DevCtrlIGMPSnooping) is enabled.
Status: current Access: not-accessible
OBJECT-TYPE    
  SwL2IGMPCtrlEntry  

swL2IGMPCtrlVid 1.3.6.1.4.1.2272.1.201.1.2.10.3.1.1
This object indicates the IGMP control entry's VLAN id. If VLAN is disabled, the Vid is always 0 and cannot be changed by management users. If VLAN is in Port-Base mode, the Vid is arranged from 1 to 12, fixed form. If VLAN is in 802.1q mode, the Vid setting can vary from 1 to 4094 by management user, and the Vid in each entry must be unique in the IGMP Control Table.
Status: current Access: read-only
OBJECT-TYPE    
  INTEGER 0..65535  

swL2IGMPQueryInterval 1.3.6.1.4.1.2272.1.201.1.2.10.3.1.2
The frequency at which IGMP Host-Query packets are transmitted on this switch.
Status: current Access: read-write
OBJECT-TYPE    
  INTEGER 1..65535  

swL2IGMPMaxResponseTime 1.3.6.1.4.1.2272.1.201.1.2.10.3.1.3
The maximum query response time on this switch.
Status: current Access: read-write
OBJECT-TYPE    
  INTEGER 1..25  

swL2IGMPRobustness 1.3.6.1.4.1.2272.1.201.1.2.10.3.1.4
The Robustness Variable allows tuning for the expected packet loss on a subnet. If a subnet is expected to be lossy, the Robustness Variable may be increased. IGMP is robust to (Robustness Variable-1) packet losses.
Status: current Access: read-write
OBJECT-TYPE    
  INTEGER 1..255  

swL2IGMPLastMemberQueryInterval 1.3.6.1.4.1.2272.1.201.1.2.10.3.1.5
The Last Member Query Interval is the Max Response Time inserted into Group-Specific Queries sent in response to Leave Group messages, and is also the amount of time between Group-Specific Query messages.
Status: current Access: read-write
OBJECT-TYPE    
  INTEGER 1..65535  

swL2IGMPHostTimeout 1.3.6.1.4.1.2272.1.201.1.2.10.3.1.6
The timer value for sending IGMP query packet when none was sent by the host in the LAN. The timer works in per-VLAN basis. Our device will be activated to send the query message if the timer is expired. Please reference RFC2236-1997.
Status: current Access: read-write
OBJECT-TYPE    
  INTEGER 1..16711450  

swL2IGMPRouteTimeout 1.3.6.1.4.1.2272.1.201.1.2.10.3.1.7
The Router Timeout is how long a host must wait after hearing a Query before it may send any IGMPv2 messages.
Status: current Access: read-write
OBJECT-TYPE    
  INTEGER 1..16711450  

swL2IGMPLeaveTimer 1.3.6.1.4.1.2272.1.201.1.2.10.3.1.8
When a querier receives a Leave Group message for a group that has group members on the reception interface, it sends Group-Specific Queries every swL2IGMPLeaveTimer to the group being left.
Status: current Access: read-write
OBJECT-TYPE    
  INTEGER 1..16711450  

swL2IGMPQueryState 1.3.6.1.4.1.2272.1.201.1.2.10.3.1.9
This object decide the IGMP query enabled or disabled.
Status: current Access: read-write
OBJECT-TYPE    
  INTEGER other(1), disabled(2), enabled(3)  

swL2IGMPCurrentState 1.3.6.1.4.1.2272.1.201.1.2.10.3.1.10
This object indicates the current IGMP query state.
Status: current Access: read-only
OBJECT-TYPE    
  INTEGER other(1), querier(2), non-querier(3)  

swL2IGMPCtrlState 1.3.6.1.4.1.2272.1.201.1.2.10.3.1.11
This object indicates the status of this entry. other(1) - this entry is currently in use but the conditions under which it will remain so are different from each of the following values. disabled(2) - IGMP funtion is disabled for this entry. enabled(3) - IGMP funtion is enabled for this entry.
Status: current Access: read-write
OBJECT-TYPE    
  INTEGER other(1), disabled(2), enabled(3)  

swL2IGMPQueryInfoTable 1.3.6.1.4.1.2272.1.201.1.2.10.4
The table contains the number current IGMP query packets which is captured by this device, as well as the IGMP query packets sent by the device.
Status: current Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    SwL2IGMPQueryInfoEntry

swL2IGMPQueryInfoEntry 1.3.6.1.4.1.2272.1.201.1.2.10.4.1
Information about current IGMP query information, provided that swL2DevCtrlIGMPSnooping and swL2IGMPCtrState of associated VLAN entry are all enabled.
Status: current Access: not-accessible
OBJECT-TYPE    
  SwL2IGMPQueryInfoEntry  

swL2IGMPInfoVid 1.3.6.1.4.1.2272.1.201.1.2.10.4.1.1
This object indicates the Vid of associated IGMP info table entry. It follows swL2IGMPCtrlVid in the associated entry of IGMP control table (swL2IGMPCtrlTable).
Status: current Access: read-only
OBJECT-TYPE    
  INTEGER 0..65535  

swL2IGMPInfoQueryCount 1.3.6.1.4.1.2272.1.201.1.2.10.4.1.2
This object indicates the number of query packets received since the IGMP function enabled, in per-VLAN basis.
Status: current Access: read-only
OBJECT-TYPE    
  INTEGER 0..65535  

swL2IGMPInfoTxQueryCount 1.3.6.1.4.1.2272.1.201.1.2.10.4.1.3
This object indicates the send count of IGMP query messages, in per-VLAN basis. In case of IGMP timer expiration, the switch sends IGMP query packets to related VLAN member ports and increment this object by 1.
Status: current Access: read-only
OBJECT-TYPE    
  INTEGER 0..65535  

swL2IGMPGroupTable 1.3.6.1.4.1.2272.1.201.1.2.10.5
The table containing current IGMP information which captured by this device, provided that swL2DevCtrlIGMPSnooping and swL2IGMPCtrlState of associated VLAN entry are all enabled. Note that the priority of IGMP table entries is lower than Filtering Table, i.e. if there is a table hash collision between the entries of IGMP Table and Filtering Table inside the switch H/W address table, then Filtering Table entry overwrite the colliding entry of IGMP Table. See swL2FilterMgmt description also.
Status: current Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    SwL2IGMPGroupEntry

swL2IGMPGroupEntry 1.3.6.1.4.1.2272.1.201.1.2.10.5.1
Information about current IGMP information which captured by this device, provided that swL2DevCtrlIGMPSnooping and swL2IGMPCtrlState of associated VLAN entry are all enabled.
Status: current Access: not-accessible
OBJECT-TYPE    
  SwL2IGMPGroupEntry  

swL2IGMPVid 1.3.6.1.4.1.2272.1.201.1.2.10.5.1.1
This object indicates the Vid of individual IGMP table entry. It shows the Vid of IGMP report information captured on network.
Status: current Access: read-only
OBJECT-TYPE    
  INTEGER 0..65535  

swL2IGMPGroupIpAddr 1.3.6.1.4.1.2272.1.201.1.2.10.5.1.2
This object is identify group ip address which is captured from IGMP packet, in per-Vlan basis.
Status: current Access: read-only
OBJECT-TYPE    
  IpAddress  

swL2IGMPMacAddr 1.3.6.1.4.1.2272.1.201.1.2.10.5.1.3
This object is identify mac address which is corresponding to swL2IGMPGroupIpAddr, in per-Vlan basis.
Status: current Access: read-only
OBJECT-TYPE    
  MacAddress  

swL2IGMPPortMap 1.3.6.1.4.1.2272.1.201.1.2.10.5.1.4
This object indicates which ports are belong to the same multicast group, in per-Vlan basis. Each multicast group has a octect string to indicate with port map. The most significant bit represents the lowest numbered port, and the least significant bit represents the highest numbered port. Thus, each port of the switch is represented by a single bit within the value of this object. If that bit has a value of '1' then that port is included in the set of ports; the port is not included if its bit has a value of '0'(Note that the setting of the bit corresponding to the port from which a frame is received is irrelevant). The 4 octets is represent one unit port according its logic port. If the unit less 32 port, the other port don't care just fill zero.
Status: current Access: read-only
OBJECT-TYPE    
  PortList  

swL2IGMPIpGroupReportCount 1.3.6.1.4.1.2272.1.201.1.2.10.5.1.5
This object indicate how much report packet was receive by our device corresponding with this entry from IGMP function enabled, in per-Vlan basis.
Status: current Access: read-only
OBJECT-TYPE    
  INTEGER 0..65535  

swL2IGMPForwardTable 1.3.6.1.4.1.2272.1.201.1.2.10.6
The table containing current IGMP forwarding information which captured by this device, provided that swL2DevCtrlIGMPSnooping and swL2IGMPCtrlState of associated VLAN entry are all enabled. Note that the priority of IGMP table entries is lower than Filtering Table, i.e. if there is a table hash collision between the entries of IGMP Table and Filtering Table inside the switch H/W address table, then Filtering Table entry overwrite the colliding entry of IGMP Table. See swL2FilterMgmt description also.
Status: current Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    SwL2IGMPForwardEntry

swL2IGMPForwardEntry 1.3.6.1.4.1.2272.1.201.1.2.10.6.1
Information about current IGMP forwarding information which captured by this device, provided that swL2DevCtrlIGMPSnooping and swL2IGMPCtrlState of associated VLAN entry are all enabled.
Status: current Access: not-accessible
OBJECT-TYPE    
  SwL2IGMPForwardEntry  

swL2IGMPForwardVid 1.3.6.1.4.1.2272.1.201.1.2.10.6.1.1
This object indicates the Vid of individual IGMP table entry. It shows the Vid of IGMP report forward information captured on network.
Status: current Access: read-only
OBJECT-TYPE    
  INTEGER 0..65535  

swL2IGMPForwardGroupIpAddr 1.3.6.1.4.1.2272.1.201.1.2.10.6.1.2
This object is identify group ip address which is captured from IGMP packet, in per-Vlan basis.
Status: current Access: read-only
OBJECT-TYPE    
  IpAddress  

swL2IGMPForwardPortMap 1.3.6.1.4.1.2272.1.201.1.2.10.6.1.3
This object indicates which ports are belong to the same multicast group, in per-Vlan basis. Each multicast group has a octect string to indicate with port map. The most significant bit represents the lowest numbered port, and the least significant bit represents the highest numbered port. Thus, each port of the switch is represented by a single bit within the value of this object. If that bit has a value of '1' then that port is included in the set of ports; the port is not included if its bit has a value of '0'(Note that the setting of the bit corresponding to the port from which a frame is received is irrelevant). The 4 octets is represent one unit port according its logic port. If the unit less 32 port, the other port don't care just fill zero.
Status: current Access: read-only
OBJECT-TYPE    
  PortList  

swL2IGMPRPTable 1.3.6.1.4.1.2272.1.201.1.2.10.7
The table allows you to designate a range of ports as being connected to multicast-enabled routers. This will ensure that all packets with such a router as its destination will reach the multicast-enabled router, regardless of protocol, etc.
Status: current Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    SwL2IGMPRPEntry

swL2IGMPRPEntry 1.3.6.1.4.1.2272.1.201.1.2.10.7.1
A list of swL2IGMPRPTable.
Status: current Access: not-accessible
OBJECT-TYPE    
  SwL2IGMPRPEntry  

swL2IGMPRPVid 1.3.6.1.4.1.2272.1.201.1.2.10.7.1.1
The Vid of the VLAN on which the router port resides.
Status: current Access: read-only
OBJECT-TYPE    
  INTEGER 0..65535  

swL2IGMPRPStaticRouterPort 1.3.6.1.4.1.2272.1.201.1.2.10.7.1.2
Specifies a range of ports which will be configured as router ports.
Status: current Access: read-write
OBJECT-TYPE    
  PortList  

swL2IGMPRPDynamicRouterPort 1.3.6.1.4.1.2272.1.201.1.2.10.7.1.3
Displays router ports that have been dynamically configued.
Status: current Access: read-only
OBJECT-TYPE    
  PortList  

swL2IGMPMulticastRouterOnly 1.3.6.1.4.1.2272.1.201.1.2.10.8
This object indicates the status of this entry. other(1) - this entry is currently in use but the conditions under which it will remain so are different from each of the following values. disabled(2) - the switch forwards all mulitcast traffic to any IP router. enabled(3) - the switch will forward all multicast traffic to the multicast router, only.
Status: current Access: read-write
OBJECT-TYPE    
  INTEGER other(1), disabled(2), enabled(3)  

swL2IGMPGroupPortTable 1.3.6.1.4.1.2272.1.201.1.2.10.9
This table describe the detail information of the member ports of the swL2IGMPGroupTable.
Status: current Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    SwL2IGMPGroupPortEntry

swL2IGMPGroupPortEntry 1.3.6.1.4.1.2272.1.201.1.2.10.9.1
Information about member ports of current swL2IGMPGroupTable.
Status: current Access: not-accessible
OBJECT-TYPE    
  SwL2IGMPGroupPortEntry  

swL2IGMPPortMember 1.3.6.1.4.1.2272.1.201.1.2.10.9.1.1
This object indicates which ports are belong to the same multicast group, in per-Vlan basis, in swL2IGMPGroupTable.
Status: current Access: read-only
OBJECT-TYPE    
  INTEGER 0..65535  

swL2IGMPPortAgingTime 1.3.6.1.4.1.2272.1.201.1.2.10.9.1.2
This object indicate the aging out timer. This value is in units of seconds.
Status: current Access: read-only
OBJECT-TYPE    
  INTEGER 1..16711450  

swL2IGMPMulticastFilter 1.3.6.1.4.1.2272.1.201.1.2.10.10
This object indicates the status of this entry. other(1) - this entry is currently in use but the conditions under which it will remain so are different from each of the following values. disabled(2) - the un-registered multicast traffic will be flooded. enabled(3) - the un-registered multicast traffic will be filtered.
Status: current Access: read-write
OBJECT-TYPE    
  INTEGER other(1), disabled(2), enabled(3)  

swL2TrafficCtrlTable 1.3.6.1.4.1.2272.1.201.1.2.12.1
This table specifys the storm traffic control configuration.
Status: current Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    SwL2TrafficCtrlEntry

swL2TrafficCtrlEntry 1.3.6.1.4.1.2272.1.201.1.2.12.1.1
A list of information specifies the storm traffic control configuration.
Status: current Access: not-accessible
OBJECT-TYPE    
  SwL2TrafficCtrlEntry  

swL2TrafficCtrlGroupIndex 1.3.6.1.4.1.2272.1.201.1.2.12.1.1.1
The index of logical port trunk. The trunk group number depend on the existence of unit and module.
Status: current Access: read-only
OBJECT-TYPE    
  INTEGER 0..65535  

swL2TrafficCtrlUnitIndex 1.3.6.1.4.1.2272.1.201.1.2.12.1.1.2
Indicates ID of the unit in the device
Status: current Access: read-only
OBJECT-TYPE    
  INTEGER 0..65535  

swL2TrafficCtrlBMStormthreshold 1.3.6.1.4.1.2272.1.201.1.2.12.1.1.3
This object to decide how much thousand packets per second broadcast/multicast (depend on swL2TrafficCtrlBcastStormCtrl, swL2TrafficCtrlMcastStormCtrl or swL2TrafficCtrlDlfStormCtrl objects whether is enabled) will active storm control. Whenever a port reaches its configured amount of packets in the one second time interval, the device will start dropping that type of packet, until the time interval has expired. Once the time interval has expired, the device will start forwarding that type of packet.
Status: current Access: read-write
OBJECT-TYPE    
  INTEGER 0..255  

swL2TrafficCtrlBcastStormCtrl 1.3.6.1.4.1.2272.1.201.1.2.12.1.1.4
This object indicates broadcast storm control function is enabled or disabled.
Status: current Access: read-write
OBJECT-TYPE    
  INTEGER other(1), disabled(2), enabled(3)  

swL2TrafficCtrlMcastStormCtrl 1.3.6.1.4.1.2272.1.201.1.2.12.1.1.5
This object indicates multicast storm control function is enabled or disabled.
Status: current Access: read-write
OBJECT-TYPE    
  INTEGER other(1), disabled(2), enabled(3)  

swL2TrafficCtrlDlfStormCtrl 1.3.6.1.4.1.2272.1.201.1.2.12.1.1.6
This object indicates destination lookup fail function is enabled or disabled.
Status: current Access: read-write
OBJECT-TYPE    
  INTEGER other(1), disabled(2), enabled(3)  

swL2QosSchedulingTable 1.3.6.1.4.1.2272.1.201.1.2.13.1
The switch contains 4 hardware priority queues. Incoming packets must be mapped to one of these four queues. Each hardware queue will transmit all of the packets in its buffer before allowing the next lower priority queue to transmit its packets. When the lowest hardware priority queue has finished transmitting all of its packets, the highest hardware priority queue can again transmit any packets it may have received.
Status: current Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    SwL2QosSchedulingEntry

swL2QosSchedulingEntry 1.3.6.1.4.1.2272.1.201.1.2.13.1.1
A list of information specifies the Qos output scheduling Table.
Status: current Access: not-accessible
OBJECT-TYPE    
  SwL2QosSchedulingEntry  

swL2QosSchedulingClassId 1.3.6.1.4.1.2272.1.201.1.2.13.1.1.1
This specifies which of the four hardware priority queues. The four hardware priority queues are identified by number, from 0 to 3, with the 0 queue being the lowest priority.
Status: current Access: read-only
OBJECT-TYPE    
  INTEGER 0..3  

swL2QosSchedulingMaxPkts 1.3.6.1.4.1.2272.1.201.1.2.13.1.1.2
Specifies the maximium number of packets the above specified hardware priority queue will be allowed to transmit before allowing the next lowest priority queue to transmit its packets.
Status: current Access: read-write
OBJECT-TYPE    
  INTEGER 0..255  

swL2QosSchedulingMaxLatency 1.3.6.1.4.1.2272.1.201.1.2.13.1.1.3
Specifies the maximum amount of time the above specified hardware priority queue will be allowed to transmit packets before allowing the next lowest hardware priority queue to begin transmitting its packets. A value between 0 and 255 can be specified. With this value multiplied by 16 ms to arrive at the total allowed time for the queue to transmit packets.
Status: current Access: read-write
OBJECT-TYPE    
  INTEGER 0..255  

swL2QosPriorityTable 1.3.6.1.4.1.2272.1.201.1.2.13.2
This table display the current priority settings on the switch.
Status: current Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    SwL2QosPriorityEntry

swL2QosPriorityEntry 1.3.6.1.4.1.2272.1.201.1.2.13.2.1
A list of information display the current priority settings on the switch.
Status: current Access: not-accessible
OBJECT-TYPE    
  SwL2QosPriorityEntry  

swL2QosPriorityType 1.3.6.1.4.1.2272.1.201.1.2.13.2.1.1
These parameters define what characteristics an incoming packet must meet. One or more of the above parameters must be defined.
Status: current Access: read-only
OBJECT-TYPE    
  INTEGER other(1), type-dscp(2), type-8021p(3), type-tcp(4), type-udp(5), type-ip(6), type-mac(7)  

swL2QosPriorityValue 1.3.6.1.4.1.2272.1.201.1.2.13.2.1.2
This object must match with swL2QosPriorityType. If the type is type-dscp(2), the range of this object is 0~63. If the type is type-8021p(3), the range of this object is 0~7. If the type is type-tcp(4) or type-udp(5), the range of this object is 1~65535.
Status: current Access: read-only
OBJECT-TYPE    
  OCTET STRING Size(1|2|4|6)  

swL2QosPriorityPriority 1.3.6.1.4.1.2272.1.201.1.2.13.2.1.3
Allows to specify a priority value to be written to the 802.1p priority field of an incoming packet that meets the criteria.
Status: current Access: read-write
OBJECT-TYPE    
  INTEGER 0..7  

swL2QosPriorityPriorityState 1.3.6.1.4.1.2272.1.201.1.2.13.2.1.4
This object indicates 802.1p priority function is enabled or disabled.
Status: current Access: read-write
OBJECT-TYPE    
  INTEGER other(1), disabled(2), enabled(3)  

swL2QosPriorityReplaceDscp 1.3.6.1.4.1.2272.1.201.1.2.13.2.1.5
Allows to specify a value to be written to the DSCP field of an incoming packet that meets the criteria.
Status: current Access: read-write
OBJECT-TYPE    
  INTEGER 0..63  

swL2QosPriorityReplaceDscpState 1.3.6.1.4.1.2272.1.201.1.2.13.2.1.6
This object indicates DSCP function is enabled or disabled.
Status: current Access: read-write
OBJECT-TYPE    
  INTEGER other(1), disabled(2), enabled(3)  

swL2QosPriorityReplacePriority 1.3.6.1.4.1.2272.1.201.1.2.13.2.1.7
This object indicates the 802.1p user priority with the priority specified above will be replaced or not.
Status: current Access: read-write
OBJECT-TYPE    
  INTEGER other(1), disabled(2), enabled(3)  

swL2QosPriorityState 1.3.6.1.4.1.2272.1.201.1.2.13.2.1.8
This object indicates the status of this entry. other(1) - this entry is currently in use but the conditions under which it will remain so are different from each of the following values. invalid(2) - writing this value to the object, and then the corresponding entry will be removed from the table. valid(3) - this entry is reside in the table.
Status: current Access: read-write
OBJECT-TYPE    
  INTEGER other(1), invalid(2), valid(3)  

managementPortLinkUp 1
The trap is sent whenever the management port is link up.
TRAP-TYPE    

managementPortLinkDown 2
The trap is sent whenever the management port is link down.
TRAP-TYPE    

swL2StormCtrlTable 1.3.6.1.4.1.2272.1.201.1.2.15.1
This table specifys the storm traffic control configuration.
Status: current Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    SwL2StormCtrlEntry

swL2StormCtrlEntry 1.3.6.1.4.1.2272.1.201.1.2.15.1.1
A list of information specifies the storm traffic control configuration.
Status: current Access: not-accessible
OBJECT-TYPE    
  SwL2StormCtrlEntry  

swL2StormCtrlPortIndex 1.3.6.1.4.1.2272.1.201.1.2.15.1.1.1
The index of logical port.
Status: current Access: read-only
OBJECT-TYPE    
  INTEGER 0..65535  

swL2StormCtrlBcastStormCtrl 1.3.6.1.4.1.2272.1.201.1.2.15.1.1.2
This object indicates broadcast storm control function is enabled or disabled.
Status: current Access: read-write
OBJECT-TYPE    
  INTEGER other(1), disabled(2), enabled(3)  

swL2StormCtrlMcastStormCtrl 1.3.6.1.4.1.2272.1.201.1.2.15.1.1.3
This object indicates multicast storm control function is enabled or disabled.
Status: current Access: read-write
OBJECT-TYPE    
  INTEGER other(1), disabled(2), enabled(3)  

swL2StormCtrlBMStormThreshold 1.3.6.1.4.1.2272.1.201.1.2.15.1.1.4
This object to decide how much percentage packets per second broadcast/multicast (depend on swL2StormCtrlBcastStormCtrl or swL2StormCtrlMcastStormCtrl objects whether is enabled) will active storm control. Whenever a port reaches its configured percent of packets in the one second time interval, the device will start dropping that type of packet, until the time interval has expired. Once the time interval has expired, the device will start forwarding that type of packet.
Status: current Access: read-write
OBJECT-TYPE    
  INTEGER 0..100  

swL2StormCtrlDlfState 1.3.6.1.4.1.2272.1.201.1.2.15.2
This object indicates destination lookup fail function is enabled or disabled.
Status: current Access: read-write
OBJECT-TYPE    
  INTEGER other(1), disabled(2), enabled(3)  

swL2StormCtrlDlfThreshold 1.3.6.1.4.1.2272.1.201.1.2.15.3
This object to decide how much packets per second destination lookup fail (depend on swL2StormCtrlDlfState objects whether is enabled) will active storm control. Whenever the device reaches its configured packets in the one second time interval, the device will start dropping that type of packet, until the time interval has expired. Once the time interval has expired, the device will start forwarding that type of packet. This value must be the multiples of 8192.
Status: current Access: read-write
OBJECT-TYPE    
  INTEGER 0..148810  

swL2CpuRateLimitTable 1.3.6.1.4.1.2272.1.201.1.2.15.4
This table specifys the CPU rate limit per port. Once too much broadcast/multicast traffic, exceed CP-Limit, comes in from a port, the port state will be disabled.
Status: current Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    SwL2CpuRateLimitEntry

swL2CpuRateLimitEntry 1.3.6.1.4.1.2272.1.201.1.2.15.4.1
A list of information specifies the CPU rate limit of the port configuration.
Status: current Access: not-accessible
OBJECT-TYPE    
  SwL2CpuRateLimitEntry  

swL2CpuRateLimitPortIndex 1.3.6.1.4.1.2272.1.201.1.2.15.4.1.1
The index of logical port.
Status: current Access: read-only
OBJECT-TYPE    
  INTEGER 0..65535  

swL2CpuRateLimitState 1.3.6.1.4.1.2272.1.201.1.2.15.4.1.2
This object indicates CPU rate limit function is enabled or disabled.
Status: current Access: read-write
OBJECT-TYPE    
  INTEGER other(1), disabled(2), enabled(3)  

swL2CpuRateLimitBcastThreshold 1.3.6.1.4.1.2272.1.201.1.2.15.4.1.3
This object to decide how much packets per second broadcast will active traffic control. Whenever a port reaches its configured packets in the one second time interval, the port will be disabled.
Status: current Access: read-write
OBJECT-TYPE    
  INTEGER 0..1700  

swL2CpuRateLimitMcastThreshold 1.3.6.1.4.1.2272.1.201.1.2.15.4.1.4
This object to decide how much packets per second multicast will active traffic control. Whenever a port reaches its configured packets in the one second time interval, the port will be disabled.
Status: current Access: read-write
OBJECT-TYPE    
  INTEGER 0..2000  

swL2CpuUtilization 1.3.6.1.4.1.2272.1.201.1.2.15.5
The utilization of CPU.
Status: current Access: read-only
OBJECT-TYPE    
  INTEGER 0..100  

swL2ACLQosTemplate1Mode 1.3.6.1.4.1.2272.1.201.1.2.16.1
This object decide the operate mode of template_1.
Status: current Access: read-write
OBJECT-TYPE    
  INTEGER other(1), security(2), qos(3), l4-switch(4)  

swL2ACLQosTemplate2Mode 1.3.6.1.4.1.2272.1.201.1.2.16.2
This object decide the operate mode of template_2.
Status: current Access: read-write
OBJECT-TYPE    
  INTEGER other(1), security(2), qos(3), l4-switch(4)  

swL2ACLQosFlowClassifierTable 1.3.6.1.4.1.2272.1.201.1.2.16.3
This table specifys the template of flow classifier.
Status: current Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    SwL2ACLQosFlowClassifierEntry

swL2ACLQosFlowClassifierEntry 1.3.6.1.4.1.2272.1.201.1.2.16.3.1
A list of information specifies the template of flow classifier.
Status: current Access: not-accessible
OBJECT-TYPE    
  SwL2ACLQosFlowClassifierEntry  

swL2ACLQosFlowClassifierTemplateId 1.3.6.1.4.1.2272.1.201.1.2.16.3.1.1
The index of template ID.
Status: current Access: read-only
OBJECT-TYPE    
  INTEGER 0..65535  

swL2ACLQosFlowClassifierCurrentMode 1.3.6.1.4.1.2272.1.201.1.2.16.3.1.2
The current operated mode of this template.
Status: current Access: read-only
OBJECT-TYPE    
  INTEGER other(1), security(2), qos(3), l4-switch(4)  

swL2ACLQosFlowClassifierSecuritySrcMask 1.3.6.1.4.1.2272.1.201.1.2.16.3.1.3
This object indicates a source IP subnet rule for the switch. If the swL2ACLQosFlowClassifierCurrentMode is not security(2), then this object must be 0.0.0.0.
Status: current Access: read-write
OBJECT-TYPE    
  IpAddress  

swL2ACLQosFlowClassifierQosFlavor 1.3.6.1.4.1.2272.1.201.1.2.16.3.1.4
These parameters define what characteristics an incoming packet must meet. One or more of the above parameters must be defined. If the swL2ACLQosFlowClassifierCurrentMode is not qos(3), then this object must be flavor-un-used(6).
Status: current Access: read-write
OBJECT-TYPE    
  INTEGER flavor-8021p(1), flavor-dscp(2), flavor-ip(3), flavor-tcp(4), flavor-udp(5), flavor-un-used(6)  

swL2ACLQosFlowClassifierL4SwitchTCPDstIp 1.3.6.1.4.1.2272.1.201.1.2.16.3.1.5
This object indicate the destination ipaddress in the configured L4 TCP-session rule entries must be checked or not. If the swL2ACLQosFlowClassifierCurrentMode is not l4-switch(4), then this object must be un-used(3).
Status: current Access: read-write
OBJECT-TYPE    
  INTEGER true(1), false(2), un-used(3)  

swL2ACLQosFlowClassifierL4SwitchTCPSrcIp 1.3.6.1.4.1.2272.1.201.1.2.16.3.1.6
This object indicate the source ipaddress in the configured L4 TCP-session rule entries must be checked or not. If the swL2ACLQosFlowClassifierCurrentMode is not l4-switch(4), then this object must be un-used(3).
Status: current Access: read-write
OBJECT-TYPE    
  INTEGER true(1), false(2), un-used(3)  

swL2ACLQosFlowClassifierL4SwitchTCPTos 1.3.6.1.4.1.2272.1.201.1.2.16.3.1.7
This object indicate the type of service in the configured L4 TCP-session rule entries must be checked or not. If the swL2ACLQosFlowClassifierCurrentMode is not l4-switch(4), then this object must be un-used(3).
Status: current Access: read-write
OBJECT-TYPE    
  INTEGER true(1), false(2), un-used(3)  

swL2ACLQosFlowClassifierL4SwitchTCPDstPort 1.3.6.1.4.1.2272.1.201.1.2.16.3.1.8
This object indicate the destination TCP port number in the configured L4 TCP-session rule entries must be checked or not. If the swL2ACLQosFlowClassifierCurrentMode is not l4-switch(4), then this object must be un-used(3).
Status: current Access: read-write
OBJECT-TYPE    
  INTEGER true(1), false(2), un-used(3)  

swL2ACLQosFlowClassifierL4SwitchTCPSrcPort 1.3.6.1.4.1.2272.1.201.1.2.16.3.1.9
This object indicate the source TCP port number in the configured L4 TCP-session rule entries must be checked or not. If the swL2ACLQosFlowClassifierCurrentMode is not l4-switch(4), then this object must be un-used(3).
Status: current Access: read-write
OBJECT-TYPE    
  INTEGER true(1), false(2), un-used(3)  

swL2ACLQosFlowClassifierL4SwitchTCPFlags 1.3.6.1.4.1.2272.1.201.1.2.16.3.1.10
This object indicate the TCP flags in the configured L4 TCP- session rule entries must be checked or not. If the swL2ACLQosFlowClassifierCurrentMode is not l4-switch(4), then this object must be un-used(3).
Status: current Access: read-write
OBJECT-TYPE    
  INTEGER true(1), false(2), un-used(3)  

swL2ACLQosFlowClassifierL4SwitchUDPDstIp 1.3.6.1.4.1.2272.1.201.1.2.16.3.1.11
This object indicate the destination ipaddress in the configured L4 UDP-session rule entries must be checked or not. If the swL2ACLQosFlowClassifierCurrentMode is not l4-switch(4), then this object must be un-used(3).
Status: current Access: read-write
OBJECT-TYPE    
  INTEGER true(1), false(2), un-used(3)  

swL2ACLQosFlowClassifierL4SwitchUDPSrcIp 1.3.6.1.4.1.2272.1.201.1.2.16.3.1.12
This object indicate the source ipaddress in the configured L4 UDP-session rule entries must be checked or not. If the swL2ACLQosFlowClassifierCurrentMode is not l4-switch(4), then this object must be un-used(3).
Status: current Access: read-write
OBJECT-TYPE    
  INTEGER true(1), false(2), un-used(3)  

swL2ACLQosFlowClassifierL4SwitchUDPTos 1.3.6.1.4.1.2272.1.201.1.2.16.3.1.13
This object indicate the type of service in the configured L4 UDP-session rule entries must be checked or not. If the swL2ACLQosFlowClassifierCurrentMode is not l4-switch(4), then this object must be un-used(3).
Status: current Access: read-write
OBJECT-TYPE    
  INTEGER true(1), false(2), un-used(3)  

swL2ACLQosFlowClassifierL4SwitchUDPDstPort 1.3.6.1.4.1.2272.1.201.1.2.16.3.1.14
This object indicate the destination UDP port number in the configured L4 UDP session rule entries must be checked or not. If the swL2ACLQosFlowClassifierCurrentMode is not l4-switch(4), then this object must be un-used(3).
Status: current Access: read-write
OBJECT-TYPE    
  INTEGER true(1), false(2), un-used(3)  

swL2ACLQosFlowClassifierL4SwitchUDPSrcPort 1.3.6.1.4.1.2272.1.201.1.2.16.3.1.15
This object indicate the source UDP port number in the configured L4 UDP session rule entries must be checked or not. If the swL2ACLQosFlowClassifierCurrentMode is not l4-switch(4), then this object must be un-used(3).
Status: current Access: read-write
OBJECT-TYPE    
  INTEGER true(1), false(2), un-used(3)  

swL2ACLQosFlowClassifierL4SwitchOtherDstIp 1.3.6.1.4.1.2272.1.201.1.2.16.3.1.16
This object indicate the destination ipaddress in the configured L4 OTHER-session rule entries must be checked or not. If the swL2ACLQosFlowClassifierCurrentMode is not l4-switch(4), then this object must be un-used(3).
Status: current Access: read-write
OBJECT-TYPE    
  INTEGER true(1), false(2), un-used(3)  

swL2ACLQosFlowClassifierL4SwitchOtherSrcIp 1.3.6.1.4.1.2272.1.201.1.2.16.3.1.17
This object indicate the source ipaddress in the configured L4 OTHER-session rule entries must be checked or not. If the swL2ACLQosFlowClassifierCurrentMode is not l4-switch(4), then this object must be un-used(3).
Status: current Access: read-write
OBJECT-TYPE    
  INTEGER true(1), false(2), un-used(3)  

swL2ACLQosFlowClassifierL4SwitchOtherTos 1.3.6.1.4.1.2272.1.201.1.2.16.3.1.18
This object indicate the type of service in the configured L4 OTHER-session rule entries must be checked or not. If the swL2ACLQosFlowClassifierCurrentMode is not l4-switch(4), then this object must be un-used(3).
Status: current Access: read-write
OBJECT-TYPE    
  INTEGER true(1), false(2), un-used(3)  

swL2ACLQosFlowClassifierL4SwitchOtherL4Protocol 1.3.6.1.4.1.2272.1.201.1.2.16.3.1.19
This object indicate the l4_protocol in the configured L4 OTHER-session rule entries must be checked or not. If the swL2ACLQosFlowClassifierCurrentMode is not l4-switch(4), then this object must be un-used(3).
Status: current Access: read-write
OBJECT-TYPE    
  INTEGER true(1), false(2), un-used(3)  

swL2ACLQosFlowClassifierL4SwitchOtherICMPMessage 1.3.6.1.4.1.2272.1.201.1.2.16.3.1.20
This object indicate the ICMP message in the configured L4 OTHER-session rule entries must be checked or not. If the swL2ACLQosFlowClassifierCurrentMode is not l4-switch(4), then this object must be un-used(3).
Status: current Access: read-write
OBJECT-TYPE    
  INTEGER true(1), false(2), un-used(3)  

swL2ACLQosFlowClassifierL4SwitchOtherIGMPType 1.3.6.1.4.1.2272.1.201.1.2.16.3.1.21
This object indicate the IGMP type in the configured L4 OTHER-session rule entries must be checked or not. If the swL2ACLQosFlowClassifierCurrentMode is not l4-switch(4), then this object must be un-used(3).
Status: current Access: read-write
OBJECT-TYPE    
  INTEGER true(1), false(2), un-used(3)  

swL2ACLQosFlowClassifierActiveRuleNumber 1.3.6.1.4.1.2272.1.201.1.2.16.3.1.22
This object indicates the number of active rule.
Status: current Access: read-only
OBJECT-TYPE    
  INTEGER 0..65535  

swL2ACLQosFlowClassifierSecurityDstMask 1.3.6.1.4.1.2272.1.201.1.2.16.3.1.23
This object indicates a destination IP subnet rule for the switch. If the swL2ACLQosFlowClassifierCurrentMode is not security(2), then this object must be 0.0.0.0.
Status: current Access: read-write
OBJECT-TYPE    
  IpAddress  

swL2ACLQosFlowClassifierVlanTable 1.3.6.1.4.1.2272.1.201.1.2.16.4
This table specifys which vlan has been binded in the template.
Status: current Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    SwL2ACLQosFlowClassifierVlanEntry

swL2ACLQosFlowClassifierVlanEntry 1.3.6.1.4.1.2272.1.201.1.2.16.4.1
A list of information which vlan has been binded in the template.
Status: current Access: not-accessible
OBJECT-TYPE    
  SwL2ACLQosFlowClassifierVlanEntry  

swL2ACLQosFlowClassifierVlanTemplateId 1.3.6.1.4.1.2272.1.201.1.2.16.4.1.1
The index of template ID.
Status: current Access: read-only
OBJECT-TYPE    
  INTEGER 0..65535  

swL2ACLQosFlowClassifierVlanVlanName 1.3.6.1.4.1.2272.1.201.1.2.16.4.1.2
The existence of VLAN name.
Status: current Access: read-only
OBJECT-TYPE    
  DisplayString Size(0..32)  

swL2ACLQosFlowClassifierVlanState 1.3.6.1.4.1.2272.1.201.1.2.16.4.1.3
This object indicates the status of this entry. other(1) - this entry is currently in use but the conditions under which it will remain so are different from each of the following values. attached(2) - this entry is reside in the table. detached(3) - writing this value to the object, and then the corresponding entry will be removed from the table.
Status: current Access: read-write
OBJECT-TYPE    
  INTEGER other(1), attached(2), detached(3)  

swL2ACLQosTemplateRuleTable 1.3.6.1.4.1.2272.1.201.1.2.16.5
This table specifys the template-depend rules.
Status: current Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    SwL2ACLQosTemplateRuleEntry

swL2ACLQosTemplateRuleEntry 1.3.6.1.4.1.2272.1.201.1.2.16.5.1
A list of information specifies the template-depend rules.
Status: current Access: not-accessible
OBJECT-TYPE    
  SwL2ACLQosTemplateRuleEntry  

swL2ACLQosTemplateRuleTemplateId 1.3.6.1.4.1.2272.1.201.1.2.16.5.1.1
The index of template ID.
Status: current Access: read-only
OBJECT-TYPE    
  INTEGER 0..65535  

swL2ACLQosTemplateRuleIndex 1.3.6.1.4.1.2272.1.201.1.2.16.5.1.2
The index of template rule.
Status: current Access: read-only
OBJECT-TYPE    
  INTEGER 0..65535  

swL2ACLQosTemplateRuleMode 1.3.6.1.4.1.2272.1.201.1.2.16.5.1.3
This object indicates the rule type of the entry.
Status: current Access: read-only
OBJECT-TYPE    
  INTEGER other(1), security(2), qos(3), l4-switch(4)  

swL2ACLQosTemplateRuleSecuritySrcIp 1.3.6.1.4.1.2272.1.201.1.2.16.5.1.4
This object indicates the source IP of flow template. If the swL2ACLQosTemplateRuleMode is not security(2), then this object will be display 0.0.0.0.
Status: current Access: read-write
OBJECT-TYPE    
  IpAddress  

swL2ACLQosTemplateRuleQosFlavor 1.3.6.1.4.1.2272.1.201.1.2.16.5.1.5
This object indicates the rule type of the QOS mode. If the swL2ACLQosTemplateRuleMode is not qos(3), then this object must be flavor-un-used(6).
Status: current Access: read-only
OBJECT-TYPE    
  INTEGER flavor-8021p(1), flavor-dscp(2), flavor-ip(3), flavor-tcp(4), flavor-udp(5), flavor-un-used(6)  

swL2ACLQosTemplateRuleQosValue 1.3.6.1.4.1.2272.1.201.1.2.16.5.1.6
This object must match with swL2ACLQosTemplateRuleQosFlavor. If the type is flavor-8021p(1), the range of this object is 0~7. If the type is flavor-dscp(2), the range of this object is 0~63. If the type is flavor-tcp(4) or flavor-udp(5), the range of this object is 1~65535. If the swL2ACLQosTemplateRuleMode is not qos(3), then this object must be NULL.
Status: current Access: read-write
OBJECT-TYPE    
  OCTET STRING Size(0|1|2|4)  

swL2ACLQosTemplateRuleQosPriority 1.3.6.1.4.1.2272.1.201.1.2.16.5.1.7
This object indicates the priority of ingress packets in QOS mode. If the swL2ACLQosTemplateRuleMode is not qos(3), then this object must be 0.
Status: current Access: read-write
OBJECT-TYPE    
  INTEGER 0..7  

swL2ACLQosTemplateRuleQosDscp 1.3.6.1.4.1.2272.1.201.1.2.16.5.1.8
This object indicates the Dscp of ingress packets in QOS mode. If the swL2ACLQosTemplateRuleMode is not qos(3), then this object must be 0.
Status: current Access: read-write
OBJECT-TYPE    
  INTEGER 0..63  

swL2ACLQosTemplateRuleL4SwitchSessionType 1.3.6.1.4.1.2272.1.201.1.2.16.5.1.9
This object indicates the rule type of the TCP-Session in L4-Switch mode. If the swL2ACLQosTemplateRuleMode is not l4-switch(4), then this object must be un-used(4).
Status: current Access: read-write
OBJECT-TYPE    
  INTEGER tcp(1), udp(2), other(3), un-used(4)  

swL2ACLQosTemplateRuleL4SwitchSessionTCPDstIp 1.3.6.1.4.1.2272.1.201.1.2.16.5.1.10
This object indicates the destination ipaddress in the configured L4 TCP-session rule entries. If the swL2ACLQosTemplateRuleMode is not l4-switch(4), then this object must be 0.0.0.0.
Status: current Access: read-write
OBJECT-TYPE    
  IpAddress  

swL2ACLQosTemplateRuleL4SwitchSessionTCPSrcIp 1.3.6.1.4.1.2272.1.201.1.2.16.5.1.11
This object indicates the source ipaddress in the configured L4 TCP-session rule entries. If the swL2ACLQosTemplateRuleMode is not l4-switch(4), then this object must be 0.0.0.0.
Status: current Access: read-write
OBJECT-TYPE    
  IpAddress  

swL2ACLQosTemplateRuleL4SwitchSessionTCPTos 1.3.6.1.4.1.2272.1.201.1.2.16.5.1.12
This object indicates the type of service in the configured L4 TCP-session rule entries. If the swL2ACLQosTemplateRuleMode is not l4-switch(4), then this object must be zero.
Status: current Access: read-write
OBJECT-TYPE    
  OCTET STRING Size(0..1)  

swL2ACLQosTemplateRuleL4SwitchSessionTCPDstPort 1.3.6.1.4.1.2272.1.201.1.2.16.5.1.13
This object indicates the destination TCP port number in the configured L4 TCP-session rule entries. If the swL2ACLQosTemplateRuleMode is not l4-switch(4), then this object must be 0.
Status: current Access: read-write
OBJECT-TYPE    
  INTEGER 0..65535  

swL2ACLQosTemplateRuleL4SwitchSessionTCPSrcPort 1.3.6.1.4.1.2272.1.201.1.2.16.5.1.14
This object indicates the source TCP port number in the configured L4 TCP-session rule entries. If the swL2ACLQosTemplateRuleMode is not l4-switch(4), then this object must be 0.
Status: current Access: read-write
OBJECT-TYPE    
  INTEGER 0..65535  

swL2ACLQosTemplateRuleL4SwitchSessionTCPFlags 1.3.6.1.4.1.2272.1.201.1.2.16.5.1.15
This object indicates the TCP flags in the configured L4 TCP- session rule entries. If the swL2ACLQosTemplateRuleMode is not l4-switch(4), then this object must be un-used(7). This object is deprecated because it just can let user to choose one of these items.
Status: deprecated Access: read-write
OBJECT-TYPE    
  INTEGER fin(1), syn(2), rst(3), psh(4), ack(5), urg(6), un-used(7)  

swL2ACLQosTemplateRuleL4SwitchSessionUDPDstIp 1.3.6.1.4.1.2272.1.201.1.2.16.5.1.16
This object indicates the destination ipaddress in the configured L4 UDP-session rule entries. If the swL2ACLQosTemplateRuleMode is not l4-switch(4), then this object must be 0.0.0.0.
Status: current Access: read-write
OBJECT-TYPE    
  IpAddress  

swL2ACLQosTemplateRuleL4SwitchSessionUDPSrcIp 1.3.6.1.4.1.2272.1.201.1.2.16.5.1.17
This object indicates the soruce ipaddress in the configured L4 UDP-session rule entries. If the swL2ACLQosTemplateRuleMode is not l4-switch(4), then this object must be 0.0.0.0.
Status: current Access: read-write
OBJECT-TYPE    
  IpAddress  

swL2ACLQosTemplateRuleL4SwitchSessionUDPTos 1.3.6.1.4.1.2272.1.201.1.2.16.5.1.18
This object indicates the type of service in the configured L4 UDP-session rule entries. If the swL2ACLQosTemplateRuleMode is not l4-switch(4), then this object must be zero.
Status: current Access: read-write
OBJECT-TYPE    
  OCTET STRING Size(0..1)  

swL2ACLQosTemplateRuleL4SwitchSessionUDPDstPort 1.3.6.1.4.1.2272.1.201.1.2.16.5.1.19
This object indicates the destination UDP port number in the configured L4 UDP-session rule entries. If the swL2ACLQosTemplateRuleMode is not l4-switch(4), then this object must be 0.
Status: current Access: read-write
OBJECT-TYPE    
  INTEGER 0..65535  

swL2ACLQosTemplateRuleL4SwitchSessionUDPSrcPort 1.3.6.1.4.1.2272.1.201.1.2.16.5.1.20
This object indicates the source UDP port number in the configured L4 UDP-session rule entries. If the swL2ACLQosTemplateRuleMode is not l4-switch(4), then this object must be 0.
Status: current Access: read-write
OBJECT-TYPE    
  INTEGER 0..65535  

swL2ACLQosTemplateRuleL4SwitchSessionOtherDstIp 1.3.6.1.4.1.2272.1.201.1.2.16.5.1.21
This object indicates the destination ipaddress in the configured L4 OTHER-session rule entries. If the swL2ACLQosTemplateRuleMode is not l4-switch(4), then this object must be 0.0.0.0.
Status: current Access: read-write
OBJECT-TYPE    
  IpAddress  

swL2ACLQosTemplateRuleL4SwitchSessionOtherSrcIp 1.3.6.1.4.1.2272.1.201.1.2.16.5.1.22
This object indicates the source ipaddress in the configured L4 OTHER-session rule entries. If the swL2ACLQosTemplateRuleMode is not l4-switch(4), then this object must be 0.0.0.0.
Status: current Access: read-write
OBJECT-TYPE    
  IpAddress  

swL2ACLQosTemplateRuleL4SwitchSessionOtherTos 1.3.6.1.4.1.2272.1.201.1.2.16.5.1.23
This object indicates the type of service in the configured L4 OTHER-session rule entries. If the swL2ACLQosTemplateRuleMode is not l4-switch(4), then this object must be zero.
Status: current Access: read-write
OBJECT-TYPE    
  OCTET STRING Size(0..1)  

swL2ACLQosTemplateRuleL4SwitchSessionOtherL4Protocol 1.3.6.1.4.1.2272.1.201.1.2.16.5.1.24
This object indicates the l4_protocol in the configured L4 OTHER-session rule entries. If the swL2ACLQosTemplateRuleMode is not l4-switch(4), then this object must be un-used(3).
Status: current Access: read-write
OBJECT-TYPE    
  INTEGER icmp(1), igmp(2), un-used(3)  

swL2ACLQosTemplateRuleL4SwitchSessionOtherICMPType 1.3.6.1.4.1.2272.1.201.1.2.16.5.1.25
This object indicates the type of ICMP message in the configured L4 OTHER-session rule entries. If the swL2ACLQosTemplateRuleMode is not l4-switch(4), then this object must be zero.
Status: current Access: read-write
OBJECT-TYPE    
  OCTET STRING Size(0..1)  

swL2ACLQosTemplateRuleL4SwitchSessionOtherICMPCode 1.3.6.1.4.1.2272.1.201.1.2.16.5.1.26
This object indicates the code of ICMP message in the configured L4 OTHER-session rule entries. If the swL2ACLQosTemplateRuleMode is not l4-switch(4), then this object must be zero.
Status: current Access: read-write
OBJECT-TYPE    
  OCTET STRING Size(0..1)  

swL2ACLQosTemplateRuleL4SwitchSessionOtherIGMPType 1.3.6.1.4.1.2272.1.201.1.2.16.5.1.27
This object indicates the IGMP type in the configured L4 OTHER-session rule entries. If the swL2ACLQosTemplateRuleMode is not l4-switch(4), then this object must be un-used(5). If the object be set to response-version-all(4), it means to create two entries with response-version-1(2) and response-version-2(3).
Status: current Access: read-write
OBJECT-TYPE    
  INTEGER query(1), response-version-1(2), response-version-2(3), response-version-all(4), un-used(5)  

swL2ACLQosTemplateRuleL4SwitchActionType 1.3.6.1.4.1.2272.1.201.1.2.16.5.1.28
This object indicates the action when a packet matches an entry of l4_switch mode. If the swL2ACLQosTemplateRuleMode is not l4-switch(4), then this object must be un-used(4).
Status: current Access: read-write
OBJECT-TYPE    
  INTEGER drop(1), forward(2), redirect(3), un-used(4)  

swL2ACLQosTemplateRuleL4SwitchActionForwardPriorityState 1.3.6.1.4.1.2272.1.201.1.2.16.5.1.29
This object decide to sending the packet to one of 8 hardware priority queues or not.
Status: current Access: read-write
OBJECT-TYPE    
  INTEGER other(1), true(2), false(3)  

swL2ACLQosTemplateRuleL4SwitchActionForwardPriority 1.3.6.1.4.1.2272.1.201.1.2.16.5.1.30
This object indicates the priority related to one of 8 hardware priority queues. If the swL2ACLQosTemplateRuleMode is not l4-switch(4) or the swL2ACLQosTemplateRuleL4SwitchActionForwardPriorityState is not true(2), this object must be 0.
Status: current Access: read-write
OBJECT-TYPE    
  INTEGER 0..7  

swL2ACLQosTemplateRuleL4SwitchActionForwardDscp 1.3.6.1.4.1.2272.1.201.1.2.16.5.1.31
If the swL2ACLQosTemplateRuleMode is not l4-switch(4) or the swL2ACLQosTemplateRuleL4SwitchActionForwardPriorityState is not true(2),, this object must be 0.
Status: current Access: read-write
OBJECT-TYPE    
  INTEGER 0..63  

swL2ACLQosTemplateRuleL4SwitchActionRedirectIp 1.3.6.1.4.1.2272.1.201.1.2.16.5.1.32
This object indicates the redirected IP address that when a packet matches an entry of l4_switch mode. If the swL2ACLQosTemplateRuleL4SwitchActionType is not redirect(3), this object must be 0.0.0.0.
Status: current Access: read-write
OBJECT-TYPE    
  IpAddress  

swL2ACLQosTemplateRuleL4SwitchActionRedirectDropUnreachable 1.3.6.1.4.1.2272.1.201.1.2.16.5.1.33
This object indicates the action of this entry. other(1) - this entry is currently in use but the conditions under which it will remain so are different from each of the following values. false(2) - routing unreachable packet by using L2/IPv4 router forwarding table. true(3) - dropping unreachable packet
Status: current Access: read-write
OBJECT-TYPE    
  INTEGER other(1), true(2), false(3)  

swL2ACLQosTemplateRuleState 1.3.6.1.4.1.2272.1.201.1.2.16.5.1.34
This object indicates the status of this entry. other(1) - this entry is currently in use but the conditions under which it will remain so are different from each of the following values. invalid(2) - writing this value to the object, and then the corresponding entry will be removed from the table. valid(3) - this entry is reside in the table.
Status: current Access: read-write
OBJECT-TYPE    
  INTEGER other(1), invalid(2), valid(3)  

swL2ACLQosTemplateRuleL4SwitchSessionTCPFlagsAll 1.3.6.1.4.1.2272.1.201.1.2.16.5.1.35
This object indicates the TCP flags in the configured L4 TCP- session rule entries. If the swL2ACLQosTemplateRuleMode is not l4-switch(4), then this object must be zero.
Status: current Access: read-write
OBJECT-TYPE    
  BITS fin(0), syn(1), rst(2), psh(3), ack(4), urg(5)  

swL2ACLQosTemplateRuleSecurityDstIp 1.3.6.1.4.1.2272.1.201.1.2.16.5.1.36
This object indicates the destination IP of flow template. If the swL2ACLQosTemplateRuleMode is not security(2), then this object will be display 0.0.0.0.
Status: current Access: read-write
OBJECT-TYPE    
  IpAddress  

swL2ACLQosDestinationIpFilterTable 1.3.6.1.4.1.2272.1.201.1.2.16.6
This table defines information for the device to filter packets with specific Destination IP address. The IP address can be a unicast address or multicast address. This table has higher priority than both static FDB table and IGMP table. It means that if a IP address appears on this table also appears on the static FDB table, the device will use the information provide by this table to process the packet.
Status: current Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    SwL2ACLQosDestinationIpFilterEntry

swL2ACLQosDestinationIpFilterEntry 1.3.6.1.4.1.2272.1.201.1.2.16.6.1
A list of information about a specific unicast/multicast IP address for which the switch has filtering information.
Status: current Access: not-accessible
OBJECT-TYPE    
  SwL2ACLQosDestinationIpFilterEntry  

swL2ACLQosDestinationIpFilterIndex 1.3.6.1.4.1.2272.1.201.1.2.16.6.1.1
The index of this rule.
Status: obsolete Access: read-only
OBJECT-TYPE    
  INTEGER 0..65535  

swL2ACLQosDestinationIpFilterIpAddr 1.3.6.1.4.1.2272.1.201.1.2.16.6.1.2
This object indicates a unicast IP address for which the switch has filtering information.
Status: current Access: read-only
OBJECT-TYPE    
  IpAddress  

swL2ACLQosDestinationIpFilterState 1.3.6.1.4.1.2272.1.201.1.2.16.6.1.3
This object indicates the status of this entry. other(1) - this entry is currently in use but the conditions under which it will remain so are different from each of the following values. invalid(2) - writing this value to the object, and then the corresponding entry will be removed from the table. valid(3) - this entry is reside in the table.
Status: current Access: read-write
OBJECT-TYPE    
  INTEGER other(1), invalid(2), valid(3)  

swL2ACLQosFDBFilterTable 1.3.6.1.4.1.2272.1.201.1.2.16.7
This table defines information for the device to filter packets with specific MAC address (either as the DA and/or as the SA). The MAC address can be a unicast address or a multicast address. This table has higher priority than both static FDB table and IGMP table. It means that if a MAC address appears on this table also appears on the static FDB table, the device will use the information provide by this table to process the packet.
Status: current Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    SwL2ACLQosFDBFilterEntry

swL2ACLQosFDBFilterEntry 1.3.6.1.4.1.2272.1.201.1.2.16.7.1
A list of information about a specific unicast/multicast MAC address for which the switch has filtering information.
Status: current Access: not-accessible
OBJECT-TYPE    
  SwL2ACLQosFDBFilterEntry  

swL2ACLQosFDBFilterIndex 1.3.6.1.4.1.2272.1.201.1.2.16.7.1.1
The index of this rule.
Status: obsolete Access: read-only
OBJECT-TYPE    
  INTEGER 0..65535  

swL2ACLQosFDBFilterVlanName 1.3.6.1.4.1.2272.1.201.1.2.16.7.1.2
The existence of VALN name.
Status: current Access: read-only
OBJECT-TYPE    
  DisplayString Size(0..32)  

swL2ACLQosFDBFilterMacAddress 1.3.6.1.4.1.2272.1.201.1.2.16.7.1.3
This object will filter on destination MAC address operates on bridged packets, but not on routed packets. And It will filter on source MAC operates on all packets.
Status: current Access: read-only
OBJECT-TYPE    
  MacAddress  

swL2ACLQosFDBFilterState 1.3.6.1.4.1.2272.1.201.1.2.16.7.1.4
This object indicates the status of this entry. other(1) - this entry is currently in use but the conditions under which it will remain so are different from each of the following values. invalid(2) - writing this value to the object, and then the corresponding entry will be removed from the table. valid(3) - this entry is reside in the table.
Status: current Access: read-write
OBJECT-TYPE    
  INTEGER other(1), invalid(2), valid(3)  

swL2ACLQosIpFragmentFilterDropPkts 1.3.6.1.4.1.2272.1.201.1.2.16.8
This object decide to drop fragmented IP packets or not.
Status: current Access: read-write
OBJECT-TYPE    
  INTEGER other(1), disabled(2), enabled(3)  

swL2ACLQosSchedulingTable 1.3.6.1.4.1.2272.1.201.1.2.16.9
The switch contains 4 hardware priority queues. Incoming packets must be mapped to one of these four queues. Each hardware queue will transmit all of the packets in its buffer before allowing the next lower priority queue to transmit its packets. When the lowest hardware priority queue has finished transmitting all of its packets, the highest hardware priority queue can again transmit any packets it may have received.
Status: current Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    SwL2ACLQosSchedulingEntry

swL2ACLQosSchedulingEntry 1.3.6.1.4.1.2272.1.201.1.2.16.9.1
A list of information specifies the Qos output scheduling Table.
Status: current Access: not-accessible
OBJECT-TYPE    
  SwL2ACLQosSchedulingEntry  

swL2ACLQosSchedulingPortIndex 1.3.6.1.4.1.2272.1.201.1.2.16.9.1.1
The index of logical port.
Status: current Access: read-only
OBJECT-TYPE    
  INTEGER 0..65535  

swL2ACLQosSchedulingClassId 1.3.6.1.4.1.2272.1.201.1.2.16.9.1.2
This specifies which of the four hardware priority queues. The four hardware priority queues are identified by number, from 0 to 3, with the 0 queue being the lowest priority.
Status: current Access: read-only
OBJECT-TYPE    
  INTEGER 0..3  

swL2ACLQosSchedulingWRRValue 1.3.6.1.4.1.2272.1.201.1.2.16.9.1.3
Specifies the weighted round robin (WRR) the above specified hardware priority queue will be allowed to transmit before allowing the next lowest priority queue to transmit its packets.
Status: current Access: read-write
OBJECT-TYPE    
  INTEGER 0..255  

swL2ACLQosMacPriorityTable 1.3.6.1.4.1.2272.1.201.1.2.16.10
This table indicates the destination mac priority in flow classifier.
Status: current Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    SwL2ACLQosMacPriorityEntry

swL2ACLQosMacPriorityEntry 1.3.6.1.4.1.2272.1.201.1.2.16.10.1
A list of information specifies the destination mac priority in flow classifier.
Status: current Access: not-accessible
OBJECT-TYPE    
  SwL2ACLQosMacPriorityEntry  

swL2ACLQosMacPriorityIndex 1.3.6.1.4.1.2272.1.201.1.2.16.10.1.1
The index of this rule.
Status: obsolete Access: read-only
OBJECT-TYPE    
  INTEGER 0..65535  

swL2ACLQosMacPriorityVlanName 1.3.6.1.4.1.2272.1.201.1.2.16.10.1.2
The existence VLAN name.
Status: current Access: read-only
OBJECT-TYPE    
  DisplayString Size(0..32)  

swL2ACLQosMacPriorityDstMacAddress 1.3.6.1.4.1.2272.1.201.1.2.16.10.1.3
This object will filter on destination MAC address operates on bridged packets, but not on routed packets. And It will filter on source MAC operates on all packets.
Status: current Access: read-only
OBJECT-TYPE    
  MacAddress  

swL2ACLQosMacPriorityPriorityValue 1.3.6.1.4.1.2272.1.201.1.2.16.10.1.4
This object indicates the priority related to one of 8 hardware priority queues.
Status: current Access: read-write
OBJECT-TYPE    
  INTEGER 0..7  

swL2ACLQosMacPriorityState 1.3.6.1.4.1.2272.1.201.1.2.16.10.1.5
This object indicates the status of this entry. other(1) - this entry is currently in use but the conditions under which it will remain so are different from each of the following values. invalid(2) - writing this value to the object, and then the corresponding entry will be removed from the table. valid(3) - this entry is reside in the table.
Status: current Access: read-write
OBJECT-TYPE    
  INTEGER other(1), invalid(2), valid(3)  

swL2MgmtPortCurrentLinkStatus 1.3.6.1.4.1.2272.1.201.1.2.17.1
This object indicates the current management port link status.
Status: current Access: read-only
OBJECT-TYPE    
  INTEGER other(1), link-pass(2), link-fail(3)  

swL2MgmtPortCurrentNwayStatus 1.3.6.1.4.1.2272.1.201.1.2.17.2
This object indicates the current management port speed and duplex mode.
Status: current Access: read-only
OBJECT-TYPE    
  INTEGER other(1), half-10Mbps(2), full-10Mbps(3), half-100Mbps(4), full-100Mbps(5)  

swL2MgmtPortAdminState 1.3.6.1.4.1.2272.1.201.1.2.17.3
This object decide the management port enabled or disabled.
Status: current Access: read-write
OBJECT-TYPE    
  INTEGER other(1), disabled(2), enabled(3)  

swL2MgmtPortNwayState 1.3.6.1.4.1.2272.1.201.1.2.17.4
Chose the management port speed, duplex mode, and N-Way function mode.
Status: current Access: read-write
OBJECT-TYPE    
  INTEGER other(1), nway-enabled(2), nway-disabled-10Mbps-Half(3), nway-disabled-10Mbps-Full(4), nway-disabled-100Mbps-Half(5), nway-disabled-100Mbps-Full(6)  

swL2MgmtPortFlowCtrlState 1.3.6.1.4.1.2272.1.201.1.2.17.5
The flow control mechanism is different between full duplex mode and half duplex mode. For half duplex mode, the jamming signal is asserted. For full duplex mode, IEEE 802.3x flow control function sends PAUSE frames and receives PAUSE frames.
Status: current Access: read-write
OBJECT-TYPE    
  INTEGER other(1), disabled(2), enabled(3)  

swL2MgmtPortLinkUpDownTrapEnable 1.3.6.1.4.1.2272.1.201.1.2.17.6
Indicates whether linkUp/linkDown traps should be generated for the management port. By default, this object should have the value enabled(3).
Status: current Access: read-write
OBJECT-TYPE    
  INTEGER other(1), disabled(2), enabled(3)  

Generation date: July 28, 2023, 16:18:13, Copyright © 2007 - 2022 - Circitor