SNAP-SWITCH-MIB
File:
SNAP-SWITCH-MIB.mib (6603 bytes)
Imported modules
Imported symbols
Defined Types
| Sk602xPortEntry |
|
| SEQUENCE |
|
|
|
| |
sk602xPort |
INTEGER |
|
| |
sk602xPortStatus |
INTEGER |
|
| |
sk602xPortDuplexStatus |
INTEGER |
|
| |
sk602xPortForwardedFrames |
Counter |
|
| |
sk602xPortRcvdLocalFrames |
Counter |
|
Defined Values
| sk |
1.3.6.1.4.1.179 |
| OBJECT IDENTIFIER |
|
|
|
| skSystems |
1.3.6.1.4.1.179.1 |
| OBJECT IDENTIFIER |
|
|
|
| skMibs |
1.3.6.1.4.1.179.2 |
| OBJECT IDENTIFIER |
|
|
|
| sk602xSysPowerupCount |
1.3.6.1.4.1.179.2.2.1.4 |
| Powerup Count. |
| Status: mandatory |
Access: read-only |
| OBJECT-TYPE |
|
|
|
| |
INTEGER |
|
|
| sk602xSysBrcastCutoffRate |
1.3.6.1.4.1.179.2.2.1.5 |
| Broadcast Cutoff Rate. (0..100000) |
| Status: mandatory |
Access: read-write |
| OBJECT-TYPE |
|
|
|
| |
INTEGER |
|
|
| sk602xPortEntry |
1.3.6.1.4.1.179.2.2.2.1 |
| The port setup entry. |
| Status: mandatory |
Access: not-accessible |
| OBJECT-TYPE |
|
|
|
| |
Sk602xPortEntry |
|
|
| sk602xPort |
1.3.6.1.4.1.179.2.2.2.1.1 |
| A number from 1 to number of ports on the switch. |
| Status: mandatory |
Access: read-only |
| OBJECT-TYPE |
|
|
|
| |
INTEGER |
|
|
| sk602xPortStatus |
1.3.6.1.4.1.179.2.2.2.1.2 |
| Port status. |
| Status: mandatory |
Access: read-only |
| OBJECT-TYPE |
|
|
|
| |
INTEGER |
up(1), down(2) |
|
| sk602xPortDuplexStatus |
1.3.6.1.4.1.179.2.2.2.1.3 |
| Port duplex status. |
| Status: mandatory |
Access: read-only |
| OBJECT-TYPE |
|
|
|
| |
INTEGER |
half(1), full(2) |
|
| sk602xPortForwardedFrames |
1.3.6.1.4.1.179.2.2.2.1.4 |
| Number of frames received on this port and forwarded to another
port on the system module for processing. |
| Status: mandatory |
Access: read-only |
| OBJECT-TYPE |
|
|
|
| |
Counter |
|
|
| sk602xPortRcvdLocalFrames |
1.3.6.1.4.1.179.2.2.2.1.5 |
| Number of frames received where the destination is on this port. |
| Status: mandatory |
Access: read-only |
| OBJECT-TYPE |
|
|
|
| |
Counter |
|
|
| sk602xSwitchIPAddress |
1.3.6.1.4.1.179.2.2.3.1 |
| Since bridges can now be accessed without an IP address,
there needs to be a way to find out there addresses. |
| Status: mandatory |
Access: read-write |
| OBJECT-TYPE |
|
|
|
| |
NetworkAddress |
|
|
| sk602xActiveAgingTime |
1.3.6.1.4.1.179.2.2.3.3 |
| Active Aging Time. |
| Status: mandatory |
Access: read-write |
| OBJECT-TYPE |
|
|
|
| |
INTEGER |
|
|
| sk602xPurgeAgingTime |
1.3.6.1.4.1.179.2.2.3.4 |
| Purge Aging Time. |
| Status: mandatory |
Access: read-write |
| OBJECT-TYPE |
|
|
|
| |
INTEGER |
|
|
| sk602xSwitchSTPStatus |
1.3.6.1.4.1.179.2.2.3.5 |
| The switch's Spanning Tree status, enter ON or OFF. |
| Status: mandatory |
Access: read-write |
| OBJECT-TYPE |
|
|
|
| |
INTEGER |
on(1), off(2) |
|