SNA-SDLC-MIB

File: SNA-SDLC-MIB.mib (139703 bytes)

Imported modules

SNMPv2-SMI SNMPv2-TC SNMPv2-CONF
RFC1213-MIB

Imported symbols

MODULE-IDENTITY OBJECT-TYPE NOTIFICATION-TYPE
Counter32 Integer32 TimeTicks
DisplayString RowStatus TimeInterval
MODULE-COMPLIANCE OBJECT-GROUP mib-2
ifIndex ifAdminStatus ifOperStatus

Defined Types

SdlcPortAdminEntry  
SEQUENCE    
  sdlcPortAdminName DisplayString
  sdlcPortAdminRole INTEGER
  sdlcPortAdminType INTEGER
  sdlcPortAdminTopology INTEGER
  sdlcPortAdminISTATUS INTEGER
  sdlcPortAdminACTIVTO TimeInterval
  sdlcPortAdminPAUSE TimeInterval
  sdlcPortAdminSERVLIM Integer32
  sdlcPortAdminSlowPollTimer TimeInterval

SdlcPortOperEntry  
SEQUENCE    
  sdlcPortOperName DisplayString
  sdlcPortOperRole INTEGER
  sdlcPortOperType INTEGER
  sdlcPortOperTopology INTEGER
  sdlcPortOperISTATUS INTEGER
  sdlcPortOperACTIVTO TimeInterval
  sdlcPortOperPAUSE TimeInterval
  sdlcPortOperSlowPollMethod INTEGER
  sdlcPortOperSERVLIM Integer32
  sdlcPortOperSlowPollTimer TimeInterval
  sdlcPortOperLastModifyTime TimeTicks
  sdlcPortOperLastFailTime TimeTicks
  sdlcPortOperLastFailCause INTEGER

SdlcPortStatsEntry  
SEQUENCE    
  sdlcPortStatsPhysicalFailures Counter32
  sdlcPortStatsInvalidAddresses Counter32
  sdlcPortStatsDwarfFrames Counter32
  sdlcPortStatsPollsIn Counter32
  sdlcPortStatsPollsOut Counter32
  sdlcPortStatsPollRspsIn Counter32
  sdlcPortStatsPollRspsOut Counter32
  sdlcPortStatsLocalBusies Counter32
  sdlcPortStatsRemoteBusies Counter32
  sdlcPortStatsIFramesIn Counter32
  sdlcPortStatsIFramesOut Counter32
  sdlcPortStatsOctetsIn Counter32
  sdlcPortStatsOctetsOut Counter32
  sdlcPortStatsProtocolErrs Counter32
  sdlcPortStatsActivityTOs Counter32
  sdlcPortStatsRNRLIMITs Counter32
  sdlcPortStatsRetriesExps Counter32
  sdlcPortStatsRetransmitsIn Counter32
  sdlcPortStatsRetransmitsOut Counter32

SdlcLSAdminEntry  
SEQUENCE    
  sdlcLSAddress INTEGER
  sdlcLSAdminName DisplayString
  sdlcLSAdminState INTEGER
  sdlcLSAdminISTATUS INTEGER
  sdlcLSAdminMAXDATASend Integer32
  sdlcLSAdminMAXDATARcv Integer32
  sdlcLSAdminREPLYTO TimeInterval
  sdlcLSAdminMAXIN INTEGER
  sdlcLSAdminMAXOUT INTEGER
  sdlcLSAdminMODULO INTEGER
  sdlcLSAdminRETRIESm INTEGER
  sdlcLSAdminRETRIESt TimeInterval
  sdlcLSAdminRETRIESn Integer32
  sdlcLSAdminRNRLIMIT TimeInterval
  sdlcLSAdminDATMODE INTEGER
  sdlcLSAdminGPoll INTEGER
  sdlcLSAdminSimRim INTEGER
  sdlcLSAdminXmitRcvCap INTEGER
  sdlcLSAdminRowStatus RowStatus

SdlcLSOperEntry  
SEQUENCE    
  sdlcLSOperName DisplayString
  sdlcLSOperRole INTEGER
  sdlcLSOperState INTEGER
  sdlcLSOperMAXDATASend Integer32
  sdlcLSOperREPLYTO TimeInterval
  sdlcLSOperMAXIN INTEGER
  sdlcLSOperMAXOUT INTEGER
  sdlcLSOperMODULO INTEGER
  sdlcLSOperRETRIESm INTEGER
  sdlcLSOperRETRIESt TimeInterval
  sdlcLSOperRETRIESn INTEGER
  sdlcLSOperRNRLIMIT TimeInterval
  sdlcLSOperDATMODE INTEGER
  sdlcLSOperLastModifyTime TimeTicks
  sdlcLSOperLastFailTime TimeTicks
  sdlcLSOperLastFailCause INTEGER
  sdlcLSOperLastFailCtrlIn OCTET STRING
  sdlcLSOperLastFailCtrlOut OCTET STRING
  sdlcLSOperLastFailFRMRInfo OCTET STRING
  sdlcLSOperLastFailREPLYTOs Counter32
  sdlcLSOperEcho INTEGER
  sdlcLSOperGPoll INTEGER
  sdlcLSOperSimRim INTEGER
  sdlcLSOperXmitRcvCap INTEGER

SdlcLSStatsEntry  
SEQUENCE    
  sdlcLSStatsBLUsIn Counter32
  sdlcLSStatsBLUsOut Counter32
  sdlcLSStatsOctetsIn Counter32
  sdlcLSStatsOctetsOut Counter32
  sdlcLSStatsPollsIn Counter32
  sdlcLSStatsPollsOut Counter32
  sdlcLSStatsPollRspsIn Counter32
  sdlcLSStatsPollRspsOut Counter32
  sdlcLSStatsLocalBusies Counter32
  sdlcLSStatsRemoteBusies Counter32
  sdlcLSStatsIFramesIn Counter32
  sdlcLSStatsIFramesOut Counter32
  sdlcLSStatsUIFramesIn Counter32
  sdlcLSStatsUIFramesOut Counter32
  sdlcLSStatsXIDsIn Counter32
  sdlcLSStatsXIDsOut Counter32
  sdlcLSStatsTESTsIn Counter32
  sdlcLSStatsTESTsOut Counter32
  sdlcLSStatsREJsIn Counter32
  sdlcLSStatsREJsOut Counter32
  sdlcLSStatsFRMRsIn Counter32
  sdlcLSStatsFRMRsOut Counter32
  sdlcLSStatsSIMsIn Counter32
  sdlcLSStatsSIMsOut Counter32
  sdlcLSStatsRIMsIn Counter32
  sdlcLSStatsRIMsOut Counter32
  sdlcLSStatsDISCIn Counter32
  sdlcLSStatsDISCOut Counter32
  sdlcLSStatsUAIn Counter32
  sdlcLSStatsUAOut Counter32
  sdlcLSStatsDMIn Counter32
  sdlcLSStatsDMOut Counter32
  sdlcLSStatsSNRMIn Counter32
  sdlcLSStatsSNRMOut Counter32
  sdlcLSStatsProtocolErrs Counter32
  sdlcLSStatsActivityTOs Counter32
  sdlcLSStatsRNRLIMITs Counter32
  sdlcLSStatsRetriesExps Counter32
  sdlcLSStatsRetransmitsIn Counter32
  sdlcLSStatsRetransmitsOut Counter32

Defined Values

snaDLC 1.3.6.1.2.1.41
This is the MIB module for objects used to manage SDLC devices.
MODULE-IDENTITY    

sdlc 1.3.6.1.2.1.41.1
OBJECT IDENTIFIER    

sdlcPortGroup 1.3.6.1.2.1.41.1.1
OBJECT IDENTIFIER    

sdlcLSGroup 1.3.6.1.2.1.41.1.2
OBJECT IDENTIFIER    

sdlcPortAdminTable 1.3.6.1.2.1.41.1.1.1
This table contains objects that can be changed to manage an SDLC port. Changing one of these parameters may take effect in the operating port immediately or may wait until the interface is restarted depending on the details of the implementation. Most of the objects in this read-write table have corresponding read-only objects in the sdlcPortOperTable that return the current operating value. The operating values may be different from these configured values if a configured parameter was changed after the interface was started.
Status: current Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    SdlcPortAdminEntry

sdlcPortAdminEntry 1.3.6.1.2.1.41.1.1.1.1
A list of configured values for an SDLC port.
Status: current Access: not-accessible
OBJECT-TYPE    
  SdlcPortAdminEntry  

sdlcPortAdminName 1.3.6.1.2.1.41.1.1.1.1.1
An octet string that defines the physical port to which this interface is assigned. It has implementation-specific significance. Its value shall be unique within the administered system. It must contain only ASCII printable characters. Should an implementation choose to accept a write operation for this object, it causes the logical port definition associated with the table instance to be moved to a different physical port. A write operation shall not take effect until the port is cycled inactive.
Status: current Access: read-write
OBJECT-TYPE    
  DisplayString Size(1..10)  

sdlcPortAdminRole 1.3.6.1.2.1.41.1.1.1.1.2
This object describes the role that the link station shall assume the next time a connection is established. Even though this is defined as a port object, it is a link station attribute in the sense that a role is per link station. However, it is not possible to vary link station roles on a particular port. For example, if an SDLC port is configured to primary, all link stations on that port must be primary.
Status: current Access: read-write
OBJECT-TYPE    
  INTEGER primary(1), secondary(2), negotiable(3)  

sdlcPortAdminType 1.3.6.1.2.1.41.1.1.1.1.3
This parameter defines whether the SDLC port is to connect to a leased or switched line. A write operation to this administrative value shall not take effect until the SDLC port has been cycled inactive.
Status: current Access: read-write
OBJECT-TYPE    
  INTEGER leased(1), switched(2)  

sdlcPortAdminTopology 1.3.6.1.2.1.41.1.1.1.1.4
This parameter defines whether the SDLC port is capable of operating in either a point-to-point or multipoint topology. sdlcPortAdminTopology == multipoint implies the port can also operate in a point-to-point topology. sdlcPortAdminTopology == pointToPoint does not imply the port can operate in a multipoint topology. A write operation to this administrative value shall not take effect until the SDLC port has been cycled inactive.
Status: current Access: read-write
OBJECT-TYPE    
  INTEGER pointToPoint(1), multipoint(2)  

sdlcPortAdminISTATUS 1.3.6.1.2.1.41.1.1.1.1.5
This parameter controls the initial value of the administrative status, ifAdminStatus, of this SDLC port at port start-up. Depending on the implementation, a write operation to this administrative object may not take effect until the SDLC port has been cycled inactive.
Status: current Access: read-write
OBJECT-TYPE    
  INTEGER inactive(1), active(2)  

sdlcPortAdminACTIVTO 1.3.6.1.2.1.41.1.1.1.1.6
This parameter defines the period of time (in 1/100ths of a second) that the port will allow a switched line to remain inactive before disconnecting. A switched line is considered to be inactive if there are no I-Frames being transferred. A value of zero indicates no timeout. Depending on the implementation, a write operation to this administered value may not take effect until the port is cycled inactive. This object only has meaning for SDLC ports where sdlcPortAdminType == switched The object descriptor contains the name of an NCP configuration parameter, ACTIVTO. Please note that the value of this object represents 1/100ths of a second while the NCP ACTIVTO is represented in seconds.
Status: current Access: read-write
OBJECT-TYPE    
  TimeInterval  

sdlcPortAdminPAUSE 1.3.6.1.2.1.41.1.1.1.1.7
This object defines the minimum elapsed time (in 1/100ths of a second) between any two traversals of the poll list for a primary SDLC port. Depending on the implementation, a write operation to this administered value may not take effect until the port is cycled inactive. The object descriptor contains the name of an NCP configuration parameter, PAUSE. Please note that the value of this object represents 1/100ths of a second while the NCP PAUSE is represented in 1/10ths of a second. This object only has meaning for SDLC ports where sdlcPortAdminRole == primary
Status: current Access: read-write
OBJECT-TYPE    
  TimeInterval  

sdlcPortAdminSERVLIM 1.3.6.1.2.1.41.1.1.1.1.8
This object defines the number of times the active poll list will be traversed before polling a station on the slow poll list for a primary, multipoint SDLC port. Depending on the implementation, a write operation to this administered value may not take effect until the port is cycled inactive. This object only has meaning for SDLC ports where sdlcPortAdminRole == primary and sdlcPortAdminTopology == multipoint
Status: current Access: read-write
OBJECT-TYPE    
  Integer32  

sdlcPortAdminSlowPollTimer 1.3.6.1.2.1.41.1.1.1.1.9
This object describes the elapsed time (in 1/100ths of a second) between polls for failed secondary link station addresses. Depending on the implementation, a write operation to this administered value may not take effect until the port is cycled inactive. This object only has meaning for SDLC ports where sdlcPortAdminRole == primary and sdlcPortAdminTopology == multipoint
Status: current Access: read-write
OBJECT-TYPE    
  TimeInterval  

sdlcPortOperTable 1.3.6.1.2.1.41.1.1.2
This table contains current SDLC port parameters. Many of these objects have corresponding objects in the sdlcPortAdminTable.
Status: current Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    SdlcPortOperEntry

sdlcPortOperEntry 1.3.6.1.2.1.41.1.1.2.1
Currently set parameters for a specific SDLC port.
Status: current Access: not-accessible
OBJECT-TYPE    
  SdlcPortOperEntry  

sdlcPortOperName 1.3.6.1.2.1.41.1.1.2.1.1
An octet string that describes the physical port to which this interface is currently attached. It has implementation-specific significance.
Status: current Access: read-only
OBJECT-TYPE    
  DisplayString Size(1..8)  

sdlcPortOperRole 1.3.6.1.2.1.41.1.1.2.1.2
This object describes the role that the link station has assumed on this connection. Even though this is defined as a port object, it is a link station attribute in the sense that a role is per link station. However, it is not possible to vary link station roles on a particular port. For example, if an SDLC port is configured to primary, all link stations on that port must be primary. The value of sdlcPortOperRole is undefined(3) whenever the link station role has not yet been established by the mode setting command.
Status: current Access: read-only
OBJECT-TYPE    
  INTEGER primary(1), secondary(2), undefined(3)  

sdlcPortOperType 1.3.6.1.2.1.41.1.1.2.1.3
This parameter defines whether the SDLC port is currently operating as though connected to a leased or switched line.
Status: current Access: read-only
OBJECT-TYPE    
  INTEGER leased(1), switched(2)  

sdlcPortOperTopology 1.3.6.1.2.1.41.1.1.2.1.4
This parameter defines whether the SDLC port is currently operating in a point-to-point or multipoint topology.
Status: current Access: read-only
OBJECT-TYPE    
  INTEGER pointToPoint(1), multipoint(2)  

sdlcPortOperISTATUS 1.3.6.1.2.1.41.1.1.2.1.5
This parameter describes the initial value of the administrative status, ifAdminStatus, of this SDLC port at last port start-up.
Status: current Access: read-only
OBJECT-TYPE    
  INTEGER inactive(1), active(2)  

sdlcPortOperACTIVTO 1.3.6.1.2.1.41.1.1.2.1.6
This parameter defines the period of time (in 100ths of a second) that the port will allow a switched line to remain inactive before disconnecting. A switched line is considered to be inactive if there are no I-Frames being transferred. The object descriptor contains the name of an NCP configuration parameter, ACTIVTO. Please note that the value of this object represents 1/100ths of a second while the NCP ACTIVTO is represented in seconds. A value of zero indicates no timeout.
Status: current Access: read-only
OBJECT-TYPE    
  TimeInterval  

sdlcPortOperPAUSE 1.3.6.1.2.1.41.1.1.2.1.7
This object describes the current minimum elapsed time (in 1/100ths of a second) between any two traversals of the poll list for a primary SDLC port. The object descriptor contains the name of an NCP configuration parameter, PAUSE. Please note that the value of this object represents 1/100ths of a second while the NCP PAUSE is represented in 1/10ths of a second. This object only has meaning for SDLC ports where sdlcPortAdminRole == primary
Status: current Access: read-only
OBJECT-TYPE    
  TimeInterval  

sdlcPortOperSlowPollMethod 1.3.6.1.2.1.41.1.1.2.1.8
This object defines the exact method that is in effect for periodically polling failed secondary link station addresses. If sdlcPortOperSlowPollMethod == servlim, then sdlcPortOperSERVLIM defines the actual polling characteristics. If sdlcPortOperSlowPollMethod == pollpause, then sdlcPortOperSlowPollTimer defines the actual polling characteristics. If sdlcPortOperSlowPollMethod == other, then the polling characteristics are modeled in vendor-specific objects. This object only has meaning for SDLC ports where sdlcPortOperRole == primary and sdlcPortOperTopology == multipoint
Status: current Access: read-only
OBJECT-TYPE    
  INTEGER servlim(1), pollpause(2), other(3)  

sdlcPortOperSERVLIM 1.3.6.1.2.1.41.1.1.2.1.9
This object describes the number of times the active poll list is currently being traversed before polling a station on the slow poll list for a primary, multipoint SDLC port. This object only has meaning for SDLC ports where sdlcPortOperRole == primary and sdlcPortOperTopology == multipoint
Status: current Access: read-only
OBJECT-TYPE    
  Integer32  

sdlcPortOperSlowPollTimer 1.3.6.1.2.1.41.1.1.2.1.10
This object describes the elapsed time (in 1/100ths of a second) between polls for failed secondary link station addresses. This object only has meaning for SDLC ports where sdlcPortOperRole == primary and sdlcPortOperTopology == multipoint
Status: current Access: read-only
OBJECT-TYPE    
  TimeInterval  

sdlcPortOperLastModifyTime 1.3.6.1.2.1.41.1.1.2.1.11
This object describes the value of sysUpTime when this port definition was last modified. If the port has not been modified, then this value shall be zero.
Status: current Access: read-only
OBJECT-TYPE    
  TimeTicks  

sdlcPortOperLastFailTime 1.3.6.1.2.1.41.1.1.2.1.12
This object describes the value of sysUpTime when this SDLC port last failed. If the port has not failed, then this value shall be zero.
Status: current Access: read-only
OBJECT-TYPE    
  TimeTicks  

sdlcPortOperLastFailCause 1.3.6.1.2.1.41.1.1.2.1.13
This enumerated object describes the cause of the last failure of this SDLC port. If the port has not failed, then this object has a value of undefined(1).
Status: current Access: read-only
OBJECT-TYPE    
  INTEGER undefined(1), physical(2)  

sdlcPortStatsTable 1.3.6.1.2.1.41.1.1.3
Each entry in this table contains statistics for a specific SDLC port.
Status: current Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    SdlcPortStatsEntry

sdlcPortStatsEntry 1.3.6.1.2.1.41.1.1.3.1
A list of statistics for an SDLC port.
Status: current Access: not-accessible
OBJECT-TYPE    
  SdlcPortStatsEntry  

sdlcPortStatsPhysicalFailures 1.3.6.1.2.1.41.1.1.3.1.1
This object reflects the total number of times this port has failed due to its physical media since port startup. At port startup time, this object must be initialized to zero.
Status: current Access: read-only
OBJECT-TYPE    
  Counter32  

sdlcPortStatsInvalidAddresses 1.3.6.1.2.1.41.1.1.3.1.2
This object reflects the total number of frames received by this port with invalid link station addresses.
Status: current Access: read-only
OBJECT-TYPE    
  Counter32  

sdlcPortStatsDwarfFrames 1.3.6.1.2.1.41.1.1.3.1.3
This object reflects the total number of frames received by this port which were delivered intact by the physical layer but were too short to be legal. Ignoring the frame check sequence (FCS), a frame is considered to be too short if it is less than 2 bytes for sdlcLSOperMODULO of eight, or if it is less than 3 bytes for sdlcLSOperMODULO of onetwentyeight.
Status: current Access: read-only
OBJECT-TYPE    
  Counter32  

sdlcPortStatsPollsIn 1.3.6.1.2.1.41.1.1.3.1.4
This object reflects the total number of polls received by this port since the port was created.
Status: current Access: read-only
OBJECT-TYPE    
  Counter32  

sdlcPortStatsPollsOut 1.3.6.1.2.1.41.1.1.3.1.5
This object reflects the total number of polls sent by this port since the port was created.
Status: current Access: read-only
OBJECT-TYPE    
  Counter32  

sdlcPortStatsPollRspsIn 1.3.6.1.2.1.41.1.1.3.1.6
This object reflects the total number of poll responses received by this port since the port was created.
Status: current Access: read-only
OBJECT-TYPE    
  Counter32  

sdlcPortStatsPollRspsOut 1.3.6.1.2.1.41.1.1.3.1.7
This object reflects the total number of poll responses sent by this port since the port was created.
Status: current Access: read-only
OBJECT-TYPE    
  Counter32  

sdlcPortStatsLocalBusies 1.3.6.1.2.1.41.1.1.3.1.8
This object reflects the total number of times that the local SDLC link stations on this port have entered a busy state (RNR). This object is initialized to zero when the port is created.
Status: current Access: read-only
OBJECT-TYPE    
  Counter32  

sdlcPortStatsRemoteBusies 1.3.6.1.2.1.41.1.1.3.1.9
This object reflects the total number of times that the adjacent (i.e., remote) SDLC link stations on this port have entered a busy state (RNR). This object is initialized to zero when the port is created.
Status: current Access: read-only
OBJECT-TYPE    
  Counter32  

sdlcPortStatsIFramesIn 1.3.6.1.2.1.41.1.1.3.1.10
This object reflects the total number of I-Frames that have been received by SDLC link stations on this port. This object is initialized to zero when the port is created.
Status: current Access: read-only
OBJECT-TYPE    
  Counter32  

sdlcPortStatsIFramesOut 1.3.6.1.2.1.41.1.1.3.1.11
This object reflects the total number of I-Frames that have been transmitted by SDLC link stations on this port. This object is initialized to zero when the port is created.
Status: current Access: read-only
OBJECT-TYPE    
  Counter32  

sdlcPortStatsOctetsIn 1.3.6.1.2.1.41.1.1.3.1.12
This object reflects the total octets received from adjacent SDLC link stations on this port. This object covers the address, control, and information field of I-Frames only. This object is initialized to zero when the port is created.
Status: current Access: read-only
OBJECT-TYPE    
  Counter32  

sdlcPortStatsOctetsOut 1.3.6.1.2.1.41.1.1.3.1.13
This object reflects the total octets transmitted to adjacent SDLC link stations on this port. This object covers the address, control, and information field of I-Frames only. This object is initialized to zero when the port is created.
Status: current Access: read-only
OBJECT-TYPE    
  Counter32  

sdlcPortStatsProtocolErrs 1.3.6.1.2.1.41.1.1.3.1.14
This object reflects the total number of times that the SDLC link stations on this port have deactivated the link as a result of having received a protocol violation from the adjacent link station. This object is initialized to zero when the port is created.
Status: current Access: read-only
OBJECT-TYPE    
  Counter32  

sdlcPortStatsActivityTOs 1.3.6.1.2.1.41.1.1.3.1.15
This object reflects the total number of times that the SDLC link stations on this port have deactivated the link as a result of no activity on the link. This object is initialized to zero when the port is created.
Status: current Access: read-only
OBJECT-TYPE    
  Counter32  

sdlcPortStatsRNRLIMITs 1.3.6.1.2.1.41.1.1.3.1.16
This object reflects the total number of times that the SDLC link stations on this port have deactivated the link as a result of its RNRLIMIT timer expiring. This object is initialized to zero when the port is created.
Status: current Access: read-only
OBJECT-TYPE    
  Counter32  

sdlcPortStatsRetriesExps 1.3.6.1.2.1.41.1.1.3.1.17
This object reflects the total number of times that the SDLC link stations on this port have deactivated the link as a result of a retry sequence being exhausted. This object is initialized to zero when the port is created.
Status: current Access: read-only
OBJECT-TYPE    
  Counter32  

sdlcPortStatsRetransmitsIn 1.3.6.1.2.1.41.1.1.3.1.18
This object reflects the total number of I-Frames retransmitted by remote link stations for all SDLC link stations on this port. This object is initialized to zero when the port is created.
Status: current Access: read-only
OBJECT-TYPE    
  Counter32  

sdlcPortStatsRetransmitsOut 1.3.6.1.2.1.41.1.1.3.1.19
This object reflects the total number of I-Frames retransmitted by all local SDLC link stations on this port. This object is initialized to zero when the port is created.
Status: current Access: read-only
OBJECT-TYPE    
  Counter32  

sdlcLSAdminTable 1.3.6.1.2.1.41.1.2.1
This table contains objects that can be changed to manage an SDLC link station. Changing one of these parameters may take effect in the operating link immediately or may wait until the link is restarted depending on the details of the implementation. The entries in sdlcLSAdminTable can be created either by an agent or a management station. The management station can create an entry in sdlcLSAdminTable by setting the appropriate value in sdlcLSAdminRowStatus. Most of the objects in this read-create table have corresponding read-only objects in the sdlcLSOperTable that reflect the current operating value. The operating values may be different from these configured values if changed by XID negotiation or if a configured parameter was changed after the link was started.
Status: current Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    SdlcLSAdminEntry

sdlcLSAdminEntry 1.3.6.1.2.1.41.1.2.1.1
A list of configured values for an SDLC link station.
Status: current Access: not-accessible
OBJECT-TYPE    
  SdlcLSAdminEntry  

sdlcLSAddress 1.3.6.1.2.1.41.1.2.1.1.1
This value is the poll address of the secondary link station for this SDLC link. It uniquely identifies the SDLC link station within a single SDLC port.
Status: current Access: read-create
OBJECT-TYPE    
  INTEGER 1..255  

sdlcLSAdminName 1.3.6.1.2.1.41.1.2.1.1.2
An octet string that defines the local name of the SDLC link station. This field may be sent in the XID3 control vector 0x0E, type 0xF7.
Status: current Access: read-create
OBJECT-TYPE    
  DisplayString Size(1..10)  

sdlcLSAdminState 1.3.6.1.2.1.41.1.2.1.1.3
This object controls the desired state of the SDLC station. The managed system shall attempt to keep the operational state, sdlcLSOperState, consistent with this value.
Status: current Access: read-create
OBJECT-TYPE    
  INTEGER inactive(1), active(2)  

sdlcLSAdminISTATUS 1.3.6.1.2.1.41.1.2.1.1.4
This parameter controls the desired state, sdlcLSAdminState, of the SDLC link station at link station start-up.
Status: current Access: read-create
OBJECT-TYPE    
  INTEGER inactive(1), active(2)  

sdlcLSAdminMAXDATASend 1.3.6.1.2.1.41.1.2.1.1.5
This object contains the maximum PDU size that the local link station thinks it can send to the adjacent link station before having received any XID from the ALS. After the maximum PDU size that the ALS can receive is known (via XID exchange) that value is reflected in sdlcLSOperMAXDATASend and takes precedence over this object. This value includes the Transmission Header (TH) and the Request Header (RH).
Status: current Access: read-create
OBJECT-TYPE    
  Integer32  

sdlcLSAdminMAXDATARcv 1.3.6.1.2.1.41.1.2.1.1.6
This object contains the maximum PDU size that the local link station can receive from the adjacent link station. This value is sent in the XID to the ALS. This value includes the Transmission Header (TH) and the Request Header (RH).
Status: current Access: read-create
OBJECT-TYPE    
  Integer32  

sdlcLSAdminREPLYTO 1.3.6.1.2.1.41.1.2.1.1.7
This object controls the reply timeout (in 1/100ths of a second) for an SDLC link station. If the link station does not receive a response to a poll or message before the specified time expires then the appropriate error recovery shall be initiated. The object descriptor contains the name of an NCP configuration parameter, REPLYTO. Please note that the value of this object represents 1/100ths of a second while the NCP REPLYTO is represented in 1/10ths of a second. Depending on the implementation, a write operation to this administered value may not change the operational value, sdlcLSOperREPLYTO, until the link station is cycled inactive. This object only has meaning for SDLC ports where sdlcPortAdminRole == primary
Status: current Access: read-create
OBJECT-TYPE    
  TimeInterval  

sdlcLSAdminMAXIN 1.3.6.1.2.1.41.1.2.1.1.8
This object controls the maximum number of unacknowledged I-frames which an SDLC link station may receive. This should range from 1 to (sdlcLSAdminMODULO - 1). This value is sent in the XID to the ALS. A write operation to this administered value will not change the operational value, sdlcLSOperMAXIN, until the link station is cycled inactive.
Status: current Access: read-create
OBJECT-TYPE    
  INTEGER 1..127  

sdlcLSAdminMAXOUT 1.3.6.1.2.1.41.1.2.1.1.9
This object controls the maximum number of consecutive unacknowledged I-frames which an SDLC link station shall send without an acknowledgement. This shall range from 1 to (sdlcLSAdminMODULO - 1). For link stations on switched SDLC lines, certain implementations may choose to override this administered value with the value received in the XID exchange. Depending on the implementation, a write operation to this administered value may not change the operational value, sdlcLSOperMAXOUT, until the link station is cycled inactive. An implementation can support only modulo 8, only modulo 128, or both.
Status: current Access: read-create
OBJECT-TYPE    
  INTEGER 1..127  

sdlcLSAdminMODULO 1.3.6.1.2.1.41.1.2.1.1.10
This object controls the modulus for an SDLC link station. This modulus determines the size of the rotating acknowledgement window used the SDLC link station pair. A write operation to this administered value will not change the operational value, sdlcLSOperMODULO, until the link station is cycled inactive. An implementation can support only modulo 8, only modulo 128, or both.
Status: current Access: read-create
OBJECT-TYPE    
  INTEGER eight(8), onetwentyeight(128)  

sdlcLSAdminRETRIESm 1.3.6.1.2.1.41.1.2.1.1.11
This object controls number of retries in a retry sequence for the local SDLC link station. A retry sequence is a series of retransmitted frames ( data or control) for which no positive acknowledgement is received. The number of times that the retry sequence is to be repeated is controlled by the object: sdlcLSAdminRETRIESn. The interval between retry sequences is controlled by the object: sdlcLSAdminRETRIESt. A value of zero indicates no retries. If the value of sdlcLSAdminRETRIESm is zero, then the values of sdlcLSAdminRETRIESt and sdlcLSAdminRETRIESn should also be zero. Depending on the implementation, a write operation to this administered value may not change the operational value, sdlcLSOperRETRIESm, until the link station is cycled inactive.
Status: current Access: read-create
OBJECT-TYPE    
  INTEGER 0..128  

sdlcLSAdminRETRIESt 1.3.6.1.2.1.41.1.2.1.1.12
This object controls the interval (in 1/100ths of a second) between retry sequences for the local SDLC link station if multiple retry sequences are specified . A retry sequence is a series of retransmitted frames ( data or control) for which no positive acknowledgement is received. The number of repeated retries sequences is controlled by the object: sdlcLSAdminRETRIESn. The retries per sequence is controlled by the object: sdlcLSAdminRETRIESm. The object descriptor contains the name of an NCP configuration parameter, RETRIESt. Please note that the value of this object represents 1/100ths of a second while the NCP RETRIESt is represented in seconds. Depending on the implementation, a write operation to this administered value may not change the operational value, sdlcLSOperRETRIESt, until the link station is cycled inactive.
Status: current Access: read-create
OBJECT-TYPE    
  TimeInterval  

sdlcLSAdminRETRIESn 1.3.6.1.2.1.41.1.2.1.1.13
This object controls the number of times that a retry sequence is repeated for the local SDLC link station. A retry sequence is a series of retransmitted frames ( data or control) for which no positive acknowledgement is received. The interval between retry sequences is controlled by the object: sdlcLSAdminRETRIESn. The retries per sequence is controlled by the object: sdlcLSAdminRETRIESm. Depending on the implementation, a write operation to this administered value may not change the operational value, sdlcLSOperRETRIESn, until the link station is cycled inactive.
Status: current Access: read-create
OBJECT-TYPE    
  Integer32  

sdlcLSAdminRNRLIMIT 1.3.6.1.2.1.41.1.2.1.1.14
This object controls the length of time (in 1/100ths of a second) that an SDLC link station will allow its adjacent link station to remain in a busy (RNR) state before declaring it inoperative. A value of sdlcLSAdminRNRLIMIT == 0 means there is no limit. The object descriptor contains the name of an NCP configuration parameter, RNRLIMIT. Please note that the value of this object represents 1/100ths of a second while the NCP RNRLIMIT is represented in minutes. Depending on the implementation, a write operation to this administered value may not change the operational value, sdlcLSOperRNRLIMIT, until the link station is cycled inactive.
Status: current Access: read-create
OBJECT-TYPE    
  TimeInterval  

sdlcLSAdminDATMODE 1.3.6.1.2.1.41.1.2.1.1.15
This object controls whether communications mode with the adjacent link station is two-way-alternate (half) or two-way-simultaneous (full). A write operation to this administered value will not change the operational value, sdlcLSOperDATMODE, until the link station is cycled inactive.
Status: current Access: read-create
OBJECT-TYPE    
  INTEGER half(1), full(2)  

sdlcLSAdminGPoll 1.3.6.1.2.1.41.1.2.1.1.16
This object describes the group poll address for this link station instance. If group poll is not in effect for this link station instance, the value for sdlcLSAdminGPoll should be zero. Depending on the implementation, a write operation to this administered value may not change the operational value, sdlcLSOperGPoll, until the link station is cycled inactive.
Status: current Access: read-create
OBJECT-TYPE    
  INTEGER 0..254  

sdlcLSAdminSimRim 1.3.6.1.2.1.41.1.2.1.1.17
This object controls the support for transmission and receipt of SIM and RIM control frames for this link station. The value of this object controls the setting of the transmit-receive capability sent in the XID field.
Status: current Access: read-create
OBJECT-TYPE    
  INTEGER no(1), yes(2)  

sdlcLSAdminXmitRcvCap 1.3.6.1.2.1.41.1.2.1.1.18
This object controls the transmit-receive capabilities for this SDLC link station. The value of this object establishes the value of the transmit-receive capability indicator sent in the XID image to the adjacent link station.
Status: current Access: read-create
OBJECT-TYPE    
  INTEGER twa(1), tws(2)  

sdlcLSAdminRowStatus 1.3.6.1.2.1.41.1.2.1.1.19
This object is used by a management station to create or delete the row entry in sdlcLSAdminTable following the RowStatus textual convention. Upon successful creation of the row, an agent automatically creates a corresponding entry in the sdlcLSOperTable with sdlcLSOperState equal to 'discontacted (1)'.
Status: current Access: read-create
OBJECT-TYPE    
  RowStatus  

sdlcLSOperTable 1.3.6.1.2.1.41.1.2.2
This table contains current SDLC link parameters. Many of these objects have corresponding objects in the sdlcLSAdminTable.
Status: current Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    SdlcLSOperEntry

sdlcLSOperEntry 1.3.6.1.2.1.41.1.2.2.1
A list of status and control values for an SDLC link station.
Status: current Access: not-accessible
OBJECT-TYPE    
  SdlcLSOperEntry  

sdlcLSOperName 1.3.6.1.2.1.41.1.2.2.1.1
An octet string that defines the name of the remote SDLC link station. This field is received in the XID3 control vector 0x0E, type 0xF7.
Status: current Access: read-only
OBJECT-TYPE    
  DisplayString Size(1..10)  

sdlcLSOperRole 1.3.6.1.2.1.41.1.2.2.1.2
This object reflects the current role that the link station is assuming. The value of sdlcLSOperRole is undefined(3) whenever the link station role has not yet been established by the mode setting command.
Status: current Access: read-only
OBJECT-TYPE    
  INTEGER primary(1), secondary(2), undefined(3)  

sdlcLSOperState 1.3.6.1.2.1.41.1.2.2.1.3
This object describes the operational state of the SDLC link station. The managed system shall attempt to keep this value consistent with the administered state, sdlcLSAdminState
Status: current Access: read-only
OBJECT-TYPE    
  INTEGER discontacted(1), contactPending(2), contacted(3), discontactPending(4)  

sdlcLSOperMAXDATASend 1.3.6.1.2.1.41.1.2.2.1.4
This object contains the actual maximum PDU size that the local link station can send to the adjacent link station. This object is established from the value received in the XID from the adjacent link station. If no XID is received, then this value is implementation dependent (for instance, it could be the value of sdlcLSAdminMAXDATASend). This value includes the Transmission Header (TH) and the Request Header (RH).
Status: current Access: read-only
OBJECT-TYPE    
  Integer32  

sdlcLSOperREPLYTO 1.3.6.1.2.1.41.1.2.2.1.5
This object reflects the current reply timeout (in 1/100ths of a second) for an SDLC link station. If the link station does not receive a response to a poll or message before the specified time expires then the appropriate error recovery shall be initiated. The object descriptor contains the name of an NCP configuration parameter, REPLYTO. Please note that the value of this object represents 1/100ths of a second while the NCP REPLYTO is represented in 1/10ths of a second. This object only has meaning for SDLC ports where sdlcPortOperRole == primary
Status: current Access: read-only
OBJECT-TYPE    
  TimeInterval  

sdlcLSOperMAXIN 1.3.6.1.2.1.41.1.2.2.1.6
This object reflects the current maximum number of unacknowledged I-frames which an SDLC link station may receive. This shall range from 1 to (sdlcLSOperMODULO - 1).
Status: current Access: read-only
OBJECT-TYPE    
  INTEGER 1..127  

sdlcLSOperMAXOUT 1.3.6.1.2.1.41.1.2.2.1.7
This object controls the maximum number of consecutive unacknowledged I-frames which an SDLC link station shall send without an acknowledgement. This shall range from 1 to (sdlcLSAdminMODULO - 1). This value may controlled by the administered MAXOUT, sdlcLSAdminMAXOUT, or by the MAXIN value received during the XID exchange.
Status: current Access: read-only
OBJECT-TYPE    
  INTEGER 1..127  

sdlcLSOperMODULO 1.3.6.1.2.1.41.1.2.2.1.8
This object reflects the current modulus for an SDLC link station. This modulus determines the size of rotating acknowledgement window used by the SDLC link station pair.
Status: current Access: read-only
OBJECT-TYPE    
  INTEGER eight(8), onetwentyeight(128)  

sdlcLSOperRETRIESm 1.3.6.1.2.1.41.1.2.2.1.9
This object controls number of retries in a retry sequence for an SDLC link station. A retry sequence is a series of retransmitted frames ( data or control) for which no positive acknowledgement is received. The current number of times that the retry sequence is to be repeated is reflected by the object: sdlcLSOperRETRIESn. The current interval between retry sequences is reflected by the object: sdlcLSOperRETRIESt.
Status: current Access: read-only
OBJECT-TYPE    
  INTEGER 0..128  

sdlcLSOperRETRIESt 1.3.6.1.2.1.41.1.2.2.1.10
This object reflects the current interval (in 1/100ths of a second) between retry sequences for an SDLC link station if multiple retry sequences are specified. A retry sequence is a series of retransmitted frames ( data or control) for which no positive acknowledgement is received. The object descriptor contains the name of an NCP configuration parameter, RETRIESt. Please note that the value of this object represents 1/100ths of a second while the NCP RETRIESt is represented in seconds. The current number of repeated retries sequences is reflected by the object: sdlcLSOperRETRIESn. The current retries per sequence is reflected by the object: sdlcLSOperRETRIESm.
Status: current Access: read-only
OBJECT-TYPE    
  TimeInterval  

sdlcLSOperRETRIESn 1.3.6.1.2.1.41.1.2.2.1.11
This object reflects the current number of times that a retry sequence is repeated for an SDLC link station. A retry sequence is a series of retransmitted frames ( data or control) for which no positive acknowledgement is received. The current interval between retry sequences is reflected by the object: sdlcLSOperRETRIESn. The current retries per sequence is reflected by the object: sdlcLSOperRETRIESm.
Status: current Access: read-only
OBJECT-TYPE    
  INTEGER 0..127  

sdlcLSOperRNRLIMIT 1.3.6.1.2.1.41.1.2.2.1.12
This object reflects the current length of time (in 1/100ths of a second) that an SDLC link station will allow its adjacent link station to remain in a busy (RNR) state before declaring it inoperative. The object descriptor contains the name of an NCP configuration parameter, RNRLIMIT. Please note that the value of this object represents 1/100ths of a second while the NCP RNRLIMIT is represented in minutes. A value of sdlcLSOperRNRLIMIT == 0 means there is no limit.
Status: current Access: read-only
OBJECT-TYPE    
  TimeInterval  

sdlcLSOperDATMODE 1.3.6.1.2.1.41.1.2.2.1.13
This object reflects whether the current communications mode with the adjacent link station is two-way-alternate (half) or two-way-simultaneous (full).
Status: current Access: read-only
OBJECT-TYPE    
  INTEGER half(1), full(2)  

sdlcLSOperLastModifyTime 1.3.6.1.2.1.41.1.2.2.1.14
This object describes the value of sysUpTime when this link station definition was last modified. If the link station has not been modified, then this value shall be zero.
Status: current Access: read-only
OBJECT-TYPE    
  TimeTicks  

sdlcLSOperLastFailTime 1.3.6.1.2.1.41.1.2.2.1.15
This object describes the value of sysUpTime when this SDLC link station last failed. If the link station has not failed, then this value shall be zero.
Status: current Access: read-only
OBJECT-TYPE    
  TimeTicks  

sdlcLSOperLastFailCause 1.3.6.1.2.1.41.1.2.2.1.16
This enumerated object reflects the cause of the last failure of this SDLC link station. If the link station has not failed, then this object will have a value of undefined(1).
Status: current Access: read-only
OBJECT-TYPE    
  INTEGER undefined(1), rxFRMR(2), txFRMR(3), noResponse(4), protocolErr(5), noActivity(6), rnrLimit(7), retriesExpired(8)  

sdlcLSOperLastFailCtrlIn 1.3.6.1.2.1.41.1.2.2.1.17
This object reflects the last control octet or octets (depending on modulus) received by this SDLC link station at the time of the last failure. If the link station has not failed, then this value has no meaning.
Status: current Access: read-only
OBJECT-TYPE    
  OCTET STRING Size(1..2)  

sdlcLSOperLastFailCtrlOut 1.3.6.1.2.1.41.1.2.2.1.18
This object reflects the last control octet or octets (depending on modulus) sent by this SDLC link station at the time of the last failure. If the link station has not failed, then this value has no meaning.
Status: current Access: read-only
OBJECT-TYPE    
  OCTET STRING Size(1..2)  

sdlcLSOperLastFailFRMRInfo 1.3.6.1.2.1.41.1.2.2.1.19
This object reflects the information field of the FRMR frame if the last failure for this SDLC link station was as a result of an invalid frame. Otherwise, this field has no meaning.
Status: current Access: read-only
OBJECT-TYPE    
  OCTET STRING Size(3)  

sdlcLSOperLastFailREPLYTOs 1.3.6.1.2.1.41.1.2.2.1.20
This object reflects the number of times that the REPLYTO timer had expired for an SDLC link station at the time of the last failure. If the link station has not failed, then this value has no meaning.
Status: current Access: read-only
OBJECT-TYPE    
  Counter32  

sdlcLSOperEcho 1.3.6.1.2.1.41.1.2.2.1.21
This object identifies whether the echo bit is in effect for this particular link station.
Status: current Access: read-only
OBJECT-TYPE    
  INTEGER no(1), yes(2)  

sdlcLSOperGPoll 1.3.6.1.2.1.41.1.2.2.1.22
This object describes the group poll address in effect for this link station instance.
Status: current Access: read-only
OBJECT-TYPE    
  INTEGER 0..254  

sdlcLSOperSimRim 1.3.6.1.2.1.41.1.2.2.1.23
This object reflects the support for transmission and receipt of SIM and RIM control frames for the adjacent link station. The value of this object is set from the XID field received from the adjacent link station.
Status: current Access: read-only
OBJECT-TYPE    
  INTEGER no(1), yes(2)  

sdlcLSOperXmitRcvCap 1.3.6.1.2.1.41.1.2.2.1.24
This object reflects the transmit-receive capabilities for the adjacent SDLC link station. The value of this object is the value of the transmit-receive capability indicator received in the XID image from the adjacent link station.
Status: current Access: read-only
OBJECT-TYPE    
  INTEGER twa(1), tws(2)  

sdlcLSStatsTable 1.3.6.1.2.1.41.1.2.3
Each entry in this table contains statistics for a specific SDLC link station.
Status: current Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    SdlcLSStatsEntry

sdlcLSStatsEntry 1.3.6.1.2.1.41.1.2.3.1
A list of statistics for an SDLC link station.
Status: current Access: not-accessible
OBJECT-TYPE    
  SdlcLSStatsEntry  

sdlcLSStatsBLUsIn 1.3.6.1.2.1.41.1.2.3.1.1
This object reflects the total basic link units (BLUs; frames) received from an adjacent SDLC link station since link station startup. At link station startup time, this object must be initialized to zero.
Status: current Access: read-only
OBJECT-TYPE    
  Counter32  

sdlcLSStatsBLUsOut 1.3.6.1.2.1.41.1.2.3.1.2
This object reflects the total basic link units (BLUs; frames), transmitted to an adjacent SDLC link station since link station startup. At link station startup time, this object must be initialized to zero.
Status: current Access: read-only
OBJECT-TYPE    
  Counter32  

sdlcLSStatsOctetsIn 1.3.6.1.2.1.41.1.2.3.1.3
This object reflects the total octets received from an adjacent SDLC link station since link station startup. This object covers the address, control, and information field of I-Frames only. At link station startup time, this object must be initialized to zero.
Status: current Access: read-only
OBJECT-TYPE    
  Counter32  

sdlcLSStatsOctetsOut 1.3.6.1.2.1.41.1.2.3.1.4
This object reflects the total octets transmitted to an adjacent SDLC link station since link station startup. This object covers the address, control, and information field of I-Frames only. At link station startup time, this object must be initialized to zero.
Status: current Access: read-only
OBJECT-TYPE    
  Counter32  

sdlcLSStatsPollsIn 1.3.6.1.2.1.41.1.2.3.1.5
This object reflects the total polls received from an adjacent SDLC link station since link station startup. At link station startup time, this object must be initialized to zero.
Status: current Access: read-only
OBJECT-TYPE    
  Counter32  

sdlcLSStatsPollsOut 1.3.6.1.2.1.41.1.2.3.1.6
This object reflects the total polls sent to an adjacent SDLC link station since link station startup. At link station startup time, this object must be initialized to zero.
Status: current Access: read-only
OBJECT-TYPE    
  Counter32  

sdlcLSStatsPollRspsOut 1.3.6.1.2.1.41.1.2.3.1.7
This object reflects the total number of poll responses sent to the adjacent SDLC link station since link station startup. This value includes I-frames that are sent in response to a poll. At link station startup time, this object must be initialized to zero.
Status: current Access: read-only
OBJECT-TYPE    
  Counter32  

sdlcLSStatsPollRspsIn 1.3.6.1.2.1.41.1.2.3.1.8
This object reflects the total number of poll responses received from the adjacent SDLC link station since station startup. This value includes I-frames that are received in response to a poll. At link station startup time, this object must be initialized to zero.
Status: current Access: read-only
OBJECT-TYPE    
  Counter32  

sdlcLSStatsLocalBusies 1.3.6.1.2.1.41.1.2.3.1.9
This object reflects the total number of times that the local SDLC link station has entered a busy state (RNR) since link station startup. At link station startup time, this object must be initialized to zero.
Status: current Access: read-only
OBJECT-TYPE    
  Counter32  

sdlcLSStatsRemoteBusies 1.3.6.1.2.1.41.1.2.3.1.10
This object reflects the total number of times that an adjacent ( remote) SDLC link station has entered a busy state (RNR) since link station startup. At link station startup time, this object must be initialized to zero.
Status: current Access: read-only
OBJECT-TYPE    
  Counter32  

sdlcLSStatsIFramesIn 1.3.6.1.2.1.41.1.2.3.1.11
This object reflects the total I-frames received from an adjacent SDLC link station since link station startup. At link station startup time, this object must be initialized to zero.
Status: current Access: read-only
OBJECT-TYPE    
  Counter32  

sdlcLSStatsIFramesOut 1.3.6.1.2.1.41.1.2.3.1.12
This object reflects the total I-frames transmitted to an adjacent SDLC link station since link station startup. At link station startup time, this object must be initialized to zero.
Status: current Access: read-only
OBJECT-TYPE    
  Counter32  

sdlcLSStatsUIFramesIn 1.3.6.1.2.1.41.1.2.3.1.13
This object reflects the total UI-frames received from an adjacent SDLC link station since link station startup.
Status: current Access: read-only
OBJECT-TYPE    
  Counter32  

sdlcLSStatsUIFramesOut 1.3.6.1.2.1.41.1.2.3.1.14
This object reflects the total UI-frames transmitted to an adjacent SDLC link station since link station startup.
Status: current Access: read-only
OBJECT-TYPE    
  Counter32  

sdlcLSStatsXIDsIn 1.3.6.1.2.1.41.1.2.3.1.15
This object reflects the total XID frames received from an adjacent SDLC link station since link station startup.
Status: current Access: read-only
OBJECT-TYPE    
  Counter32  

sdlcLSStatsXIDsOut 1.3.6.1.2.1.41.1.2.3.1.16
This object reflects the total XID frames transmitted to an adjacent SDLC link station since link station startup.
Status: current Access: read-only
OBJECT-TYPE    
  Counter32  

sdlcLSStatsTESTsIn 1.3.6.1.2.1.41.1.2.3.1.17
This object reflects the total TEST frames, commands or responses, received from an adjacent SDLC link station since link station startup.
Status: current Access: read-only
OBJECT-TYPE    
  Counter32  

sdlcLSStatsTESTsOut 1.3.6.1.2.1.41.1.2.3.1.18
This object reflects the total TEST frames, commands or responses, transmitted to an adjacent SDLC link station since link station startup.
Status: current Access: read-only
OBJECT-TYPE    
  Counter32  

sdlcLSStatsREJsIn 1.3.6.1.2.1.41.1.2.3.1.19
This object reflects the total REJ frames received from an adjacent SDLC link station since link station startup.
Status: current Access: read-only
OBJECT-TYPE    
  Counter32  

sdlcLSStatsREJsOut 1.3.6.1.2.1.41.1.2.3.1.20
This object reflects the total REJ frames transmitted to an adjacent SDLC link station since link station startup.
Status: current Access: read-only
OBJECT-TYPE    
  Counter32  

sdlcLSStatsFRMRsIn 1.3.6.1.2.1.41.1.2.3.1.21
This object reflects the total frame reject (FRMR) frames received from an adjacent SDLC link station since link station startup.
Status: current Access: read-only
OBJECT-TYPE    
  Counter32  

sdlcLSStatsFRMRsOut 1.3.6.1.2.1.41.1.2.3.1.22
This object reflects the total frame reject (FRMR) frames transmitted to an adjacent SDLC link station since link station startup.
Status: current Access: read-only
OBJECT-TYPE    
  Counter32  

sdlcLSStatsSIMsIn 1.3.6.1.2.1.41.1.2.3.1.23
This object reflects the total set initialization mode (SIM) frames received from an adjacent SDLC link station since link station startup.
Status: current Access: read-only
OBJECT-TYPE    
  Counter32  

sdlcLSStatsSIMsOut 1.3.6.1.2.1.41.1.2.3.1.24
This object reflects the total set initialization mode (SIM) frames transmitted to an adjacent SDLC link station since link station startup. At link station startup time, this object must be initialized to zero.
Status: current Access: read-only
OBJECT-TYPE    
  Counter32  

sdlcLSStatsRIMsIn 1.3.6.1.2.1.41.1.2.3.1.25
This object reflects the total request initialization mode (RIM) frames received from an adjacent SDLC link station since link station startup. At link station startup time, this object must be initialized to zero.
Status: current Access: read-only
OBJECT-TYPE    
  Counter32  

sdlcLSStatsRIMsOut 1.3.6.1.2.1.41.1.2.3.1.26
This object reflects the total request initialization mode (RIM) frames transmitted to an adjacent SDLC link station since link station startup. At link station startup time, this object must be initialized to zero.
Status: current Access: read-only
OBJECT-TYPE    
  Counter32  

sdlcLSStatsDISCIn 1.3.6.1.2.1.41.1.2.3.1.27
This object reflects the total number of disconnect (DISC) requests received from an adjacent SDLC link station since link station startup. At link station startup time, this object must be initialized to zero.
Status: current Access: read-only
OBJECT-TYPE    
  Counter32  

sdlcLSStatsDISCOut 1.3.6.1.2.1.41.1.2.3.1.28
This object reflects the total number of disconnect (DISC) requests transmitted to an adjacent SDLC link station since link station startup. At link station startup time, this object must be initialized to zero.
Status: current Access: read-only
OBJECT-TYPE    
  Counter32  

sdlcLSStatsUAIn 1.3.6.1.2.1.41.1.2.3.1.29
This object reflects the total number of unnumbered acknowledgements (UA) requests received from an adjacent SDLC link station since link station startup. At link station startup time, this object must be initialized to zero.
Status: current Access: read-only
OBJECT-TYPE    
  Counter32  

sdlcLSStatsUAOut 1.3.6.1.2.1.41.1.2.3.1.30
This object reflects the total number of unnumbered acknowledgements (UA) requests transmitted to an adjacent SDLC link station since link station startup. At link station startup time, this object must be initialized to zero.
Status: current Access: read-only
OBJECT-TYPE    
  Counter32  

sdlcLSStatsDMIn 1.3.6.1.2.1.41.1.2.3.1.31
This object reflects the total number of disconnect mode (DM) requests received from an adjacent SDLC link station since link station startup. At link station startup time, this object must be initialized to zero.
Status: current Access: read-only
OBJECT-TYPE    
  Counter32  

sdlcLSStatsDMOut 1.3.6.1.2.1.41.1.2.3.1.32
This object reflects the total number of disconnect mode (DM) requests transmitted to an adjacent SDLC link station since link station startup. At link station startup time, this object must be initialized to zero.
Status: current Access: read-only
OBJECT-TYPE    
  Counter32  

sdlcLSStatsSNRMIn 1.3.6.1.2.1.41.1.2.3.1.33
This object reflects the total number of set normal response mode (SNRM/SNRME) requests received from an adjacent SDLC link station since link station startup. At link station startup time, this object must be initialized to zero.
Status: current Access: read-only
OBJECT-TYPE    
  Counter32  

sdlcLSStatsSNRMOut 1.3.6.1.2.1.41.1.2.3.1.34
This object reflects the total number of set normal response mode (SNRM/SNRME) requests transmitted to an adjacent SDLC link station since link station startup. At link station startup time, this object must be initialized to zero.
Status: current Access: read-only
OBJECT-TYPE    
  Counter32  

sdlcLSStatsProtocolErrs 1.3.6.1.2.1.41.1.2.3.1.35
This object reflects the total occurrences, since link station startup, where this SDLC link station has inactivated the link as a result of receiving a frame from its adjacent link station which was in violation of the protocol. At link station startup time, this object must be initialized to zero.
Status: current Access: read-only
OBJECT-TYPE    
  Counter32  

sdlcLSStatsActivityTOs 1.3.6.1.2.1.41.1.2.3.1.36
This object reflects the total occurrences, since startup, where this SDLC link station has inactivated the link as a result of no activity on the link. At link station startup time, this object must be initialized to zero.
Status: current Access: read-only
OBJECT-TYPE    
  Counter32  

sdlcLSStatsRNRLIMITs 1.3.6.1.2.1.41.1.2.3.1.37
This object reflects the total occurrences, since startup, where this SDLC link station has inactivated the link as a result of its RNRLIMIT timer expiring. At link station startup time, this object must be initialized to zero.
Status: current Access: read-only
OBJECT-TYPE    
  Counter32  

sdlcLSStatsRetriesExps 1.3.6.1.2.1.41.1.2.3.1.38
This object reflects the total occurrences, since startup, where this SDLC link station has inactivated the link as a result of a retry sequence being exhausted. At link station startup time, this object must be initialized to zero.
Status: current Access: read-only
OBJECT-TYPE    
  Counter32  

sdlcLSStatsRetransmitsIn 1.3.6.1.2.1.41.1.2.3.1.39
This object reflects the total number of information frames retransmitted by the remote link station because the N(s) received from that link station indicated that one or more information frames sent by that station were lost. This event causes the first missing information frame of a window and all subsequent information frames to be retransmitted. At link station startup time, this object must be initialized to zero. Management: If the value of sdlcLSStatsRetransmitsIn grows over time, then the quality of the serial line is in question. You might want to look at decreasing the value for sdlcLSAdminMAXDATASend to compensate for the lower quality line.
Status: current Access: read-only
OBJECT-TYPE    
  Counter32  

sdlcLSStatsRetransmitsOut 1.3.6.1.2.1.41.1.2.3.1.40
This object reflects the total number of information frames retransmitted to a remote link station because the N(r) received from that link station indicated that one or more information frames sent to that station were lost. This event causes the first missing information frame of a window and all subsequent information frames to be retransmitted. At link station startup time, this object must be initialized to zero. Management: If the value of sdlcLSStatsRetransmitsOut grows over time, then the quality of the serial line is in question. You might want to look at decreasing the value for sdlcLSAdminMAXDATASend to compensate for the lower quality line.
Status: current Access: read-only
OBJECT-TYPE    
  Counter32  

sdlcTraps 1.3.6.1.2.1.41.1.3
OBJECT IDENTIFIER    

sdlcPortStatusChange 1.3.6.1.2.1.41.1.3.1
This trap indicates that the state of an SDLC port has transitioned to active or inactive.
Status: current Access: read-only
NOTIFICATION-TYPE    

sdlcLSStatusChange 1.3.6.1.2.1.41.1.3.2
This trap indicates that the state of an SDLC link station has transitioned to contacted or discontacted.
Status: obsolete Access: read-only
NOTIFICATION-TYPE    

sdlcLSStatusChange1 1.3.6.1.2.1.41.1.3.3
This trap indicates that the state of an SDLC link station has transitioned to contacted or discontacted.
Status: current Access: read-only
NOTIFICATION-TYPE    

sdlcConformance 1.3.6.1.2.1.41.1.4
OBJECT IDENTIFIER    

sdlcCompliances 1.3.6.1.2.1.41.1.4.1
OBJECT IDENTIFIER    

sdlcGroups 1.3.6.1.2.1.41.1.4.2
OBJECT IDENTIFIER    

sdlcCoreCompliance 1.3.6.1.2.1.41.1.4.1.1
The core compliance statement for all SDLC nodes.
Status: obsolete Access: read-only
MODULE-COMPLIANCE    

sdlcCoreComplianceV11R01 1.3.6.1.2.1.41.1.4.1.4
The core compliance statement for all SDLC nodes.
Status: current Access: read-only
MODULE-COMPLIANCE    

sdlcPrimaryCompliance 1.3.6.1.2.1.41.1.4.1.2
The compliance statement for all nodes that are performing the role of a Primary link station.
Status: current Access: read-only
MODULE-COMPLIANCE    

sdlcPrimaryMultipointCompliance 1.3.6.1.2.1.41.1.4.1.3
The compliance statement for all nodes that are performing the role of a primary link station on a multipoint line.
Status: current Access: read-only
MODULE-COMPLIANCE    

sdlcCoreGroups 1.3.6.1.2.1.41.1.4.2.1
OBJECT IDENTIFIER    

sdlcCorePortAdminGroup 1.3.6.1.2.1.41.1.4.2.1.1
The sdlcCorePortAdminGroup defines objects which are common to the PortAdmin group of all compliant link stations.
Status: obsolete Access: read-only
OBJECT-GROUP    

sdlcCorePortAdminGroupV11R01 1.3.6.1.2.1.41.1.4.2.1.7
The sdlcCorePortAdminGroup defines objects which are common to the PortAdmin group of all compliant link stations.
Status: current Access: read-only
OBJECT-GROUP    

sdlcCorePortOperGroup 1.3.6.1.2.1.41.1.4.2.1.2
The sdlcCorePortOperGroup defines objects which are common to the PortOper group of all compliant link stations.
Status: obsolete Access: read-only
OBJECT-GROUP    

sdlcCorePortOperGroupV11R01 1.3.6.1.2.1.41.1.4.2.1.8
The sdlcCorePortOperGroup defines objects which are common to the PortOper group of all compliant link stations.
Status: current Access: read-only
OBJECT-GROUP    

sdlcCorePortStatsGroup 1.3.6.1.2.1.41.1.4.2.1.3
The sdlcCorePortStatsGroup defines objects which are common to the PortStats group of all compliant link stations.
Status: obsolete Access: read-only
OBJECT-GROUP    

sdlcCorePortStatsGroupV11R01 1.3.6.1.2.1.41.1.4.2.1.9
The sdlcCorePortStatsGroup defines objects which are common to the PortStats group of all compliant link stations.
Status: current Access: read-only
OBJECT-GROUP    

sdlcCoreLSAdminGroup 1.3.6.1.2.1.41.1.4.2.1.4
The sdlcCorePortAdminGroup defines objects which are common to the PortAdmin group of all compliant link stations.
Status: obsolete Access: read-only
OBJECT-GROUP    

sdlcCoreLSAdminGroupV11R01 1.3.6.1.2.1.41.1.4.2.1.10
The sdlcCorePortAdminGroup defines objects which are common to the PortAdmin group of all compliant link stations.
Status: current Access: read-only
OBJECT-GROUP    

sdlcCoreLSOperGroup 1.3.6.1.2.1.41.1.4.2.1.5
The sdlcCorePortOperGroup defines objects which are common to the PortOper group of all compliant link stations.
Status: obsolete Access: read-only
OBJECT-GROUP    

sdlcCoreLSOperGroupV11R01 1.3.6.1.2.1.41.1.4.2.1.11
The sdlcCorePortOperGroup defines objects which are common to the PortOper group of all compliant link stations.
Status: current Access: read-only
OBJECT-GROUP    

sdlcCoreLSStatsGroup 1.3.6.1.2.1.41.1.4.2.1.6
The sdlcCorePortStatsGroup defines objects which are common to the PortStats group of all compliant link stations.
Status: obsolete Access: read-only
OBJECT-GROUP    

sdlcCoreLSStatsGroupV11R01 1.3.6.1.2.1.41.1.4.2.1.12
The sdlcCorePortStatsGroup defines objects which are common to the PortStats group of all compliant link stations.
Status: current Access: read-only
OBJECT-GROUP    

sdlcPrimaryGroups 1.3.6.1.2.1.41.1.4.2.2
OBJECT IDENTIFIER    

sdlcPrimaryGroup 1.3.6.1.2.1.41.1.4.2.2.1
The sdlcPrimaryGroup defines objects which are common to all compliant primary link stations.
Status: current Access: read-only
OBJECT-GROUP    

sdlcPrimaryMultipointGroup 1.3.6.1.2.1.41.1.4.2.2.2
The sdlcPrimaryMultipointGroup defines objects which are common to all compliant primary link stations that are in a multipoint topology.
Status: current Access: read-only
OBJECT-GROUP