SLE-MLSQOS-MIB

File: SLE-MLSQOS-MIB.mib (147848 bytes)

Imported modules

DASAN-SMI SLE-TC-MIB SNMP-FRAMEWORK-MIB
SNMPv2-CONF SNMPv2-SMI SNMPv2-TC

Imported symbols

sleMgmt SleControlStatusType SleControlRequestResultType
SnmpAdminString OBJECT-GROUP TimeTicks
Integer32 Unsigned32 Gauge32
Counter64 OBJECT-TYPE MODULE-IDENTITY
TEXTUAL-CONVENTION

Defined Types

MlsQosStatusType  
Enable(1) : enabled in the system. Disable(0) : Disable in system.
TEXTUAL-CONVENTION    
  INTEGER enable(1), disable(0)  

MlsQosMappingType  
CosToCos(1) : CosToQueue(2) : DscpToDscp(3) : DscpToQueue(4) : ExpToExp(5) : ExpToQueue(6) :
TEXTUAL-CONVENTION    
  INTEGER cosToCos(1), cosToQueue(2), dscpToDscp(3), dscpToQueue(4), expToExp(5), expToQueue(6), expToClass(7)  

ACLMatchType  
ACL Match Types mac (1), EthType (2) L3Proto(3)
TEXTUAL-CONVENTION    
  INTEGER mac(1), ethType(2), l3Proto(3)  

ACLMatchActionType  
deny(0) deny the packets permit(1) permit. remark(2) mark the packets
TEXTUAL-CONVENTION    
  INTEGER deny(0), permit(1), remark(2)  

ACLEtherType  
WORD Ethertype value - (0x600-0xffff) ip4 IPv4 Ethertype - 0x0800 ip6 IPv6 Ethertype - 0x86dd mpls MPLS Ethertype - 0x8847
TEXTUAL-CONVENTION    
  OCTET STRING  

AclTcpUdpPortActionType  
eq(1) Equals to neq(2) Not equals to lt(3) Lower Than gt(4) Greather Than
TEXTUAL-CONVENTION    
  INTEGER eq(1), neq(2), lt(3), gt(4)  

ClassMapMatchType  
cos (1) , innerCos(2), ipDscp (3), ipPrecedence (4), ip6Dscp (5), ip6Precedence (6), tcpSrcPort (7), tcpDstPort (8), udpSrcPort (9), udpDstPort (10), VlanId (11), innerVlanId (12), layer4SrcPort (13) layer4DstPort (14)
TEXTUAL-CONVENTION    
  INTEGER cos(1), innerCos(2), ipDscp(3), ipPrecedence(4), ip6Dscp(5), ip6Precedence(6), tcpSrcPort(7), tcpDstPort(8), udpSrcPort(9), udpDstPort(10), vlanId(11), innerVlanId(12), layer4SrcPort(13), layer4DstPort(14)  

ClassMapMatchRangeType  
tcpSrcPort (1), tcpDstPort (2), udpSrcPort (3), udpDstPort (4), VlanId (5), layer4SrcPort (6), layer4DstPort (7)
TEXTUAL-CONVENTION    
  INTEGER tcpSrcPort(1), tcpDstPort(2), udpSrcPort(3), udpDstPort(4), vlanId(5), layer4SrcPort(6), layer4DstPort(7)  

PmapPriorityType  
low(0) medium(1) high(2) highest(3)
TEXTUAL-CONVENTION    
  INTEGER low(0), medium(1), high(2), highest(3)  

PmapPoliceType  
srtcm(1) trtcm(2)
TEXTUAL-CONVENTION    
  INTEGER srtcm(1), trtcm(2)  

PmapExceedActionType  
none (0) drop (1) set-dscp-transmit (2) set-tos-transmit (3) set-cos-transmit (4) transmit (7)
TEXTUAL-CONVENTION    
  INTEGER none(0), drop(1), setDscpTransmit(2), setTosTransmit(3), setCosTransmit(4), transmit(7)  

PmapViolateActionType  
none(0) drop(1) set-dscp-transmit(2) set-cos-transmit(3) set-tos-transmit(4) transmit (5)
TEXTUAL-CONVENTION    
  INTEGER none(0), drop(1), dscpTx(2), cosTx(3), tosTx(4), transmit(5)  

PmapSetActionType  
cos (1), cpu-cos (2), ip-dscp (3), ip-precedence (4), redirect-to-port (5), mirror-to-port (6), vlan (7), ip6-dscp (8), ip6-precedence (9), cpu-copy (10), deny (11), qos-group(12), none(13), queue(14), vlan-cos(15)
TEXTUAL-CONVENTION    
  INTEGER cos(1), cpuCos(2), ipDscp(3), ipPrecedence(4), redirectToPort(5), mirrorToPort(6), vlan(7), ip6Dscp(8), ip6Precedence(9), cpuCopy(10), deny(11), qosGroup(12), none(13), queue(14), vlanCos(15)  

MlsQosIntfTrustState  
cos (1) dscp (2)
TEXTUAL-CONVENTION    
  INTEGER cos(1), dscp(2)  

MlsQosInterfaceMapingType  
cos (1) Configure interface default CoS values cos-cos (2) Specify cos-cos cos-queue (3) Specify cos-queue map dscp (4) Set the default DSCP vlaue dscp-dscp(5) Specify dscp-dscp dscp-queue (6) DSCP-to-QUEUE exp-exp(7) Specify exp-exp trust (8) Configure port trust state trust-passthrough (9) COnfigure port trust pass-through state cosToClass (10) configure cos to class dscpToClass (11) configure dscp to class
TEXTUAL-CONVENTION    
  INTEGER cos(1), cosToCos(2), cosToQueue(3), dscp(4), dscpToDscp(5), dscpToQueue(6), expToExp(7), trust(8), trustPassThrough(9), cosToClass(10), dscpToClass(11)  

MlsQosIntfQueProfilingType  
shaping (1), wrrQWt (2), wrrRandomDetect (3), tailDrop (4), strictQ (5)
TEXTUAL-CONVENTION    
  INTEGER shaping(1), wrrQWt(2), wrrRandomDetect(3), tailDrop(4), strictQ(5), reservedBandwidth(6)  

ACLMacType  
src(1) Src Mac dst(2) Dst Mac srcWildcard(3) Src Wildcard bits dstWildcard(4) Dst Wildcard Bits
TEXTUAL-CONVENTION    
  INTEGER src(1), dst(2), srcWildcard(3), dstWildcard(4)  

ACLIpType  
src(1) Src Mac dst(2) Dst Mac srcWildcard(3) Src Wildcard bits dstWildcard(4) Dst Wildcard Bits host(5) any(6)
TEXTUAL-CONVENTION    
  INTEGER src(1), dst(2), srcWildcard(3), dstWildcard(4)  

PolMapClassMatchPrioType  
high(1) : highest(2) : low(3) : medium(4) :
TEXTUAL-CONVENTION    
  INTEGER high(1), highest(2), low(3), medium(4)  

PoliceExceedActionType  
drop(1) : set-cos-transmit(2) : set-dscp-transmit(3) : set-tos-transmit(4) : transmit (5)
TEXTUAL-CONVENTION    
  INTEGER drop(1), setCosTransmit(2), setDscpTransmit(3), setTosTransmit(4), transmit(5)  

SleMlsQosAggPoliceEntry  
SEQUENCE    
  sleMlsQosAggPoliceIndex Integer32
  sleMlsQosAggPoliceName OCTET STRING
  sleMlsQosAggPoliceTrafficRate Integer32
  sleMlsQosAggPoliceBurstSize Integer32

SleMlsQosACLEntry  
SEQUENCE    
  sleMlsQosACLIndex Integer32
  sleMlsQosACLFilterIndex Integer32
  sleMlsQosACLName OCTET STRING
  sleMlsQosACLMatchType ACLMatchType
  sleMlsQosACLMatchAction ACLMatchActionType
  sleMlsQosACLEtherType ACLEtherType
  sleMlsQosACLL3Protocol Integer32
  sleMlsQosACLSrcIpAddress OCTET STRING
  sleMlsQosACLDstIpAddress OCTET STRING
  sleMlsQosACLSrcIpAddrMask OCTET STRING
  sleMlsQosACLDstIpAddrMask OCTET STRING
  sleMlsQosACLSrcMacAddress OCTET STRING
  sleMlsQosACLDstMacAddress OCTET STRING
  sleMlsQosACLSrcMacAddrMask OCTET STRING
  sleMlsQosACLDstMacAddrMask OCTET STRING
  sleMlsQosACLTcpUdpSrcPortAction AclTcpUdpPortActionType
  sleMlsQosACLTcpUdpDstPortAction AclTcpUdpPortActionType
  sleMlsQosACLTcpUdpSrcPort Integer32
  sleMlsQosACLTcpUdpDstPort Integer32
  sleMlsQosACLNameSrcIpExactMatch Integer32
  sleMlsQosACLActionRemarkDesc OCTET STRING
  sleMlsQosACLIcmpType Integer32
  sleMlsQosACLIcmpCode Integer32
  sleMlsQosACLTcpUdpSrcPortEnd Integer32
  sleMlsQosACLTcpUdpDstPortEnd Integer32

SleMlsQosClassMapEntry  
SEQUENCE    
  sleMlsQosClassMapName OCTET STRING
  sleMlsQosClassMapMatchCosValue Integer32
  sleMlsQosClassMapMatchInnerCosValue Integer32
  sleMlsQosClassMapMatchEgressInterface OCTET STRING
  sleMlsQosClassMapMatchEtherType OCTET STRING
  sleMlsQosClassMapMatchSrcIpAddr OCTET STRING
  sleMlsQosClassMapMatchDstIpAddr OCTET STRING
  sleMlsQosClassMapMatchSrcIpMaskLen Integer32
  sleMlsQosClassMapMatchDstIpMaskLen Integer32
  sleMlsQosClassMapMatchSrcIpV6Addr OCTET STRING
  sleMlsQosClassMapMatchDstIpV6Addr OCTET STRING
  sleMlsQosClassMapMatchSrcIpV6MaskLen Integer32
  sleMlsQosClassMapMatchDstIpV6MaskLen Integer32
  sleMlsQosClassMapMatchIpDscp Integer32
  sleMlsQosClassMapMatchIpPrecedence Integer32
  sleMlsQosClassMapMatchIp6Dscp Integer32
  sleMlsQosClassMapMatchIp6Precedence Integer32
  sleMlsQosClassMapMatchTcpSrcPort OCTET STRING
  sleMlsQosClassMapMatchTcpDstPort OCTET STRING
  sleMlsQosClassMapMatchTcpSrcPortRange OCTET STRING
  sleMlsQosClassMapMatchTcpDstPortRange OCTET STRING
  sleMlsQosClassMapMatchUdpSrcPort OCTET STRING
  sleMlsQosClassMapMatchUdpDstPort OCTET STRING
  sleMlsQosClassMapMatchUdpSrcPortRange OCTET STRING
  sleMlsQosClassMapMatchUdpDstPortRange OCTET STRING
  sleMlsQosClassMapMatchSrcMacAddr OCTET STRING
  sleMlsQosClassMapMatchSrcMacMask OCTET STRING
  sleMlsQosClassMapMatchDstMacAddr OCTET STRING
  sleMlsQosClassMapMatchDstMacMask OCTET STRING
  sleMlsQosClassMapMatchVlanId OCTET STRING
  sleMlsQosClassMapMatchVlanIdRange OCTET STRING
  sleMlsQosClassMapMatchInnerVlanId Integer32
  sleMlsQosClassMapMatchVlanTpid OCTET STRING
  sleMlsQosClassMapMatchAccessGroup OCTET STRING
  sleMlsQosClassMapMatchLayer4SrcPort OCTET STRING
  sleMlsQosClassMapMatchLayer4DstPort OCTET STRING
  sleMlsQosClassMapMatchLayer4SrcPortRange OCTET STRING
  sleMlsQosClassMapMatchLayer4DstPortRange OCTET STRING
  sleMplsQosClassMapMatchCriteria INTEGER

SleMlsQosPolicyMapEntry  
SEQUENCE    
  sleMlsQosPmapName OCTET STRING
  sleMlsQosPmapClassName OCTET STRING
  sleMlsQosPmapClassMatchPriority PmapPriorityType
  sleMlsQosPmapClassOperMode INTEGER
  sleMlsQosPmapClassPoliceType PmapPoliceType
  sleMlsQosPmapClassPoliceCIR Integer32
  sleMlsQosPmapClassPolicePIR Integer32
  sleMlsQosPmapClassPoliceCBS Integer32
  sleMlsQosPmapClassPoliceEBS Integer32
  sleMlsQosPmapClassPoliceExdAction PmapExceedActionType
  sleMlsQosPmapClassPoliceExdActionCos Integer32
  sleMlsQosPmapClassPoliceExdActionDscp Integer32
  sleMlsQosPmapClassPoliceExdActionTos Integer32
  sleMlsQosPmapClassPoliceExdActionViolateAction PmapViolateActionType
  sleMlsQosPmapClassPoliceExdActionViolateValue Integer32
  sleMlsQosPmapClassPoliceAggregateName OCTET STRING
  sleMlsQosPmapClassSetActionDeny Integer32
  sleMlsQosPmapClassSetActionCos Integer32
  sleMlsQosPmapClassSetActionCpuCos Integer32
  sleMlsQosPmapClassSetActionIpDscp Integer32
  sleMlsQosPmapClassSetActionIp6Dscp Integer32
  sleMlsQosPmapClassSetActionIpPrecedence Integer32
  sleMlsQosPmapClassSetActionIp6Precedence Integer32
  sleMlsQosPmapClassSetActionMirrorToPortVal OCTET STRING
  sleMlsQosPmapClassSetActionRedirectToPortVal OCTET STRING
  sleMlsQosPmapClassSetActionVlanId Integer32
  sleMlsQosPmapClassSetActionVlanCos Integer32
  sleMlsQosPmapClassSetActionQosGroup INTEGER
  sleMplsQosPmapClassSetActionQueue INTEGER
  sleMplsQosPmapClassSetActionCopyCpu INTEGER

SleMlsQosInterfaceEntry  
SEQUENCE    
  sleMlsQosInterfaceIndex Integer32
  sleMlsQosInterfaceName OCTET STRING
  sleMlsQosInterfaceTrustState MlsQosIntfTrustState
  sleMlsQosInterfaceCos Integer32
  sleMlsQosInterfaceCosOverride Integer32
  sleMlsQosInterfaceCosToCos OCTET STRING
  sleMlsQosInterfaceCosToQueue OCTET STRING
  sleMlsQosInterfaceDscp Integer32
  sleMlsQosInterfaceDscpToDscp OCTET STRING
  sleMlsQosInterfaceDscpToQueue OCTET STRING
  sleMlsQosInterfaceExpToExp OCTET STRING
  sleMlsQosInterfaceTrafficShapeRate Integer32
  sleMlsQosInterfaceTrafficShapeBurst Integer32
  sleMlsQosInterfaceInputPolicyMap OCTET STRING
  sleMlsQosInterfaceOutputPolicyMap OCTET STRING
  sleMlsQosInterfaceTrustPassthroughCos Integer32
  sleMlsQosInterfaceTrustPassthroughDscp Integer32
  sleHQosInterfaceCosToClass OCTET STRING
  sleHQosInterfaceDscpToClass OCTET STRING
  sleHQosInterfaceReplace INTEGER
  sleMlsQosInterfaceTrafficIfgExclude Integer32
  sleMlsQosInterfaceTrafficPolicingRate Integer32
  sleMlsQosInterfaceTrafficPolicingBurst Integer32

SleMlsQosIntfQueEntry  
SEQUENCE    
  sleMlsQosIntfQueIntfIndex Integer32
  sleMlsQosIntfQueId Integer32
  sleMlsQosIntfQueShapeQueueRate Integer32
  sleMlsQosIntfQueWrrQueueWeight Integer32
  sleMlsQosIntfQueWrrRandomDetectMinThr Integer32
  sleMlsQosIntfQueWrrRandomDetectMaxThr Integer32
  sleMlsQosIntfQueWrrRandomDetectExpWt Integer32
  sleMlsQosIntfQueTailDropThr Integer32
  sleMlsQosIntfQueStrictQueue Integer32
  sleMlsQosIntfQueRandomDetectDropStart Integer32
  sleMlsQosIntfQueRandomDetectDropSlope Integer32
  sleMlsQosIntfQueRandomDetectColor INTEGER
  sleMlsQosIntfQueReservedBandwidth Integer32

SleMlsQosQStatsEntry  
SEQUENCE    
  sleMlsQosQstatsIfIndex Integer32
  sleMlsQosQId Integer32
  sleMlsQosWredGreenDropPkts Counter64
  sleMlsQosWredYellowDropPkts Counter64
  sleMlsQosWredRedDropPkts Counter64
  sleMlsQosTailDropPkts Counter64
  sleMlsQosTailDropBytes Counter64
  sleMlsQosQStatsOutPkts Counter64
  sleMlsQosQStatsOutBytes Counter64
  sleMlsQosQStatsMcastOutPkts Counter64
  sleMlsQosQStatsMcastOutBytes Counter64
  sleMlsQosQStatsDropPkts Counter64
  sleMlsQosQStatsDropBytes Counter64
  sleMlsQosQStatsMcastDropPkts Counter64
  sleMlsQosQStatsMcastDropBytes Counter64
  sleMlsQosQStatsEnqueuedPkts Counter64
  sleMlsQosQStatsEnqueuedBytes Counter64

SleHqosClassMapQueueInfoEntry  
SEQUENCE    
  sleHqosClassMapQueueInfoName OCTET STRING
  sleHqosClassMapQueueInfoMatchGroup INTEGER

SleHqosPolicyMapQueueInfoEntry  
SEQUENCE    
  sleHqosPolicyMapQueueInfoName OCTET STRING
  sleHqosPolicyMapQueueInfoShape SnmpAdminString
  sleHqosPolicyMapQueueInfoBandwidth SnmpAdminString
  sleHqosPolicyMapQueueInfoBandwidthRemainingPercent INTEGER
  sleHqosPolicyMapQueueInfoQueueLimit SnmpAdminString
  sleHqosPolicyMapQueueInfoServicePolicyName SnmpAdminString
  sleHqosPolicyMapQueueInfoPriority INTEGER
  sleHqosPolicyMapQueueInfoRDMinThreshold SnmpAdminString
  sleHqosPolicyMapQueueInfoRDMaxThreshold SnmpAdminString

Defined Values

sleMlsQos 1.3.6.1.4.1.6296.101.28
This MIB contains all informations about ML QOS supported features.
MODULE-IDENTITY    

sleMlsQosGlobal 1.3.6.1.4.1.6296.101.28.1
OBJECT IDENTIFIER    

sleMlsQosGlobalInfo 1.3.6.1.4.1.6296.101.28.1.1
OBJECT IDENTIFIER    

sleMlsQosStatus 1.3.6.1.4.1.6296.101.28.1.1.1
Enable / Disable MlQos enable (1) disable (0)
OBJECT-TYPE    
  MlsQosStatusType  

sleMlsQosMapCosToCos 1.3.6.1.4.1.6296.101.28.1.1.2
Global incoming Cos to outgoing Cos mapping.
OBJECT-TYPE    
  OCTET STRING  

sleMlsQosMapCosToQueue 1.3.6.1.4.1.6296.101.28.1.1.3
Global incoming Cos to outgoing queue mapping.
OBJECT-TYPE    
  OCTET STRING  

sleMlsQosMapDscpToDscp 1.3.6.1.4.1.6296.101.28.1.1.4
Global incoming dscp to outgoing dscp mapping.
OBJECT-TYPE    
  OCTET STRING  

sleMlsQosMapDscpToQueue 1.3.6.1.4.1.6296.101.28.1.1.5
Global incoming dscp to outgoing queue mapping.
OBJECT-TYPE    
  OCTET STRING  

sleMlsQosMapExpToExp 1.3.6.1.4.1.6296.101.28.1.1.6
Global incoming exp to outgoing exp mapping.
OBJECT-TYPE    
  OCTET STRING  

sleMlsQosMapExpToQueue 1.3.6.1.4.1.6296.101.28.1.1.7
Global incoming exp to outgoing queue mapping.
OBJECT-TYPE    
  OCTET STRING  

sleMlsQosMapStrictQueueId 1.3.6.1.4.1.6296.101.28.1.1.8
Queues with Strict scheduling
OBJECT-TYPE    
  OCTET STRING  

sleMlsQosMapWrrQueueWeight 1.3.6.1.4.1.6296.101.28.1.1.9
Queue weight for Weighted round robin scheduling. If the queue wt is given 0, then the queue becomes strict queue
OBJECT-TYPE    
  OCTET STRING  

sleMlsQosMapCpuMaxPpsRate 1.3.6.1.4.1.6296.101.28.1.1.10
Rate limiting for CPU. Defines Max packets per second to CPU
OBJECT-TYPE    
  OCTET STRING  

sleMlsQosMapCpuQueueWeight 1.3.6.1.4.1.6296.101.28.1.1.11
weight for Cpu Queues
OBJECT-TYPE    
  OCTET STRING  

sleMlsQosMapNodeCpuMaxPpsRate 1.3.6.1.4.1.6296.101.28.1.1.12
node Rate limiting for CPU. Defines Max packets per second to CPU
OBJECT-TYPE    
  OCTET STRING  

sleMlsQosMapNodeCpuQueueWeight 1.3.6.1.4.1.6296.101.28.1.1.13
node weight for Cpu Queues
OBJECT-TYPE    
  OCTET STRING  

sleMlsQosMapExpToClass 1.3.6.1.4.1.6296.101.28.1.1.14
Exp - to - class mapping
OBJECT-TYPE    
  OCTET STRING  

sleHQosStatistics 1.3.6.1.4.1.6296.101.28.1.1.15
Hqos has feature to disable or enable statistics so this object is only applicable when hqos is enabled
OBJECT-TYPE    
  MlsQosStatusType  

sleQosPhbPriorityColor 1.3.6.1.4.1.6296.101.28.1.1.16
qos phb-priority-color Ex: PHB Name | Priority Color ------------------------------------------- be | 0 red cs0 | 0 green cs1 | 1 green af11 | 1 yellow af12 | 1 red af13 | 0 green cs2 | 2 green af21 | 2 green af22 | 2 yellow af23 | 2 red cs3 | 3 green af31 | 4 red af32 | 3 green af33 | 3 yellow cs4 | 4 green af41 | 5 yellow af42 | 5 red af43 | 4 green cs5 | 5 green ef | 6 red cs6 | 6 yellow cs7 | 7 green
OBJECT-TYPE    
  OCTET STRING  

sleHQosDefaultClassToDscp 1.3.6.1.4.1.6296.101.28.1.1.17
Default Class to DSCP Ex: QoS PHB map to DSCP: PHB Name | dscp ------------------------------------------- be | 0 be | 0 cs1 | 9 af11 | 10 af12 | 12 af13 | 14 cs2 | 16 af21 | 18 af22 | 20 af23 | 22 cs3 | 24 af31 | 26 af32 | 28 af33 | 30 cs4 | 32 af41 | 34 af42 | 35 af43 | 38 cs5 | 40 ef | 46 cs6 | 48 cs7 | 56
OBJECT-TYPE    
  OCTET STRING  

sleQosDefaultCosToClassTrust 1.3.6.1.4.1.6296.101.28.1.1.18
qos default cos to class trust Ex:QoS Cos+Cfi/DEI to CLASS: COS CFI/DEI | CLASS ------------------------------------------- 0 0 | cs0 0 1 | cs0 1 0 | cs1 1 1 | cs1 2 0 | cs2 2 1 | cs2 3 0 | cs3 3 1 | cs3 4 0 | cs4 4 1 | cs4 5 0 | cs5 5 1 | cs5 6 0 | cs6 6 1 | cs6 7 0 | cs7 7 1 | cs7
OBJECT-TYPE    
  OCTET STRING  

sleQosDefaultCosToClassNoTrust 1.3.6.1.4.1.6296.101.28.1.1.19
qos Default cos to class no trust Ex: QoS Cos+Cfi/DEI to CLASS: COS CFI/DEI | CLASS ------------------------------------------- 0 0 | be 0 1 | be 1 0 | be 1 1 | be 2 0 | be 2 1 | be 3 0 | be 3 1 | be 4 0 | be 4 1 | be 5 0 | be 5 1 | be 6 0 | be 6 1 | be 7 0 | be 7 1 | be
OBJECT-TYPE    
  OCTET STRING  

sleQosDefaultDscpToClassTrust 1.3.6.1.4.1.6296.101.28.1.1.20
qos default dscp to class trust Ex: QoS Dscp to CLASS: DSCP | CLASS ------------------------------------------- 0 | be 1 | be 2 | be 3 | be 4 | be 5 | be 6 | be 7 | be 8 | cs1 9 | be 10 | af11 11 | be 12 | af12 13 | be 14 | af13 15 | be 16 | cs2 17 | be 18 | af21 19 | be 20 | af22 21 | be 22 | af23 23 | be 24 | cs3 25 | be 26 | af31 27 | be 28 | af32 29 | be 30 | af33 31 | be 32 | cs4 33 | be 34 | af41 35 | be 36 | af42 37 | be 38 | af43 39 | be 40 | cs5 41 | be 42 | be 43 | be 44 | be 45 | be 46 | ef 47 | be 48 | cs6 49 | be 50 | be 51 | be 52 | be 53 | be 54 | be 55 | be 56 | cs7 57 | be 58 | be 59 | be 60 | be 61 | be 62 | be 63 | be
OBJECT-TYPE    
  OCTET STRING  

sleQosDefaultDscpToClassNoTrust 1.3.6.1.4.1.6296.101.28.1.1.21
qos defualt dscp to class no trust Ex: QoS Dscp to CLASS: DSCP | CLASS ------------------------------------------- 0 | be 1 | be 2 | be 3 | be 4 | be 5 | be 6 | be 7 | be 8 | be 9 | be 10 | be 11 | be 12 | be 13 | be 14 | be 15 | be 16 | be 17 | be 18 | be 19 | be 20 | be 21 | be 22 | be 23 | be 24 | be 25 | be 26 | be 27 | be 28 | be 29 | be 30 | be 31 | be 32 | be 33 | be 34 | be 35 | be 36 | be 37 | be 38 | be 39 | be 40 | be 41 | be 42 | be 43 | be 44 | be 45 | be 46 | be 47 | be 48 | be 49 | be 50 | be 51 | be 52 | be 53 | be 54 | be 55 | be 56 | be 57 | be 58 | be 59 | be 60 | be 61 | be 62 | be 63 | be
OBJECT-TYPE    
  OCTET STRING  

sleMlsQosGlobalControl 1.3.6.1.4.1.6296.101.28.1.2
OBJECT IDENTIFIER    

sleMlsQosGlobalControlRequest 1.3.6.1.4.1.6296.101.28.1.2.1
The configuration commands, and user can configure functions via setting this entry as proper value.
OBJECT-TYPE    
  INTEGER setMlQosStatus(1), setMlsQosMapping(2), unSetMlsQosMapping(3), setMlsQosStrictQueue(4), unSetMlsQosStrictQueue(5), setMlsQosWrr(6), unSetMlsQosWrr(7), setMlsQosCpuRate(8), setMlsQosCpuQueueWt(9), setMlsQosNodeCpuRate(10), setMlsQosNodeCpuQueueWt(11), setHQosStatistics(12), unsetHQosStatistics(13)  

sleMlsQosGlobalControlStatus 1.3.6.1.4.1.6296.101.28.1.2.2
status of user command. User have to check this value as .busy. or .idle. before do setRequest.
OBJECT-TYPE    
  SleControlStatusType  

sleMlsQosGlobalCtrlTimer 1.3.6.1.4.1.6296.101.28.1.2.3
the wait-time until setRequest end. In case of short-time command, this value is 0
OBJECT-TYPE    
  Gauge32  

sleMlsQosGlobalControlTimeStamp 1.3.6.1.4.1.6296.101.28.1.2.4
the time stamp of the last command. (don.t care)
OBJECT-TYPE    
  TimeTicks  

sleMlsQosGlobalControlReqResult 1.3.6.1.4.1.6296.101.28.1.2.5
Result of the last command.
OBJECT-TYPE    
  SleControlRequestResultType  

sleMlsQosCtrlGlobalStatus 1.3.6.1.4.1.6296.101.28.1.2.6
Enable / Disable MlQos enable (1) disable (0)
OBJECT-TYPE    
  MlsQosStatusType  

sleMlsQosGlobalControlMappingType 1.3.6.1.4.1.6296.101.28.1.2.7
Below Mapping Types can be configured cosToCos(1), cosToQueue(2), dscpToDscp(3), dscpToQueue(4), expToExp(5), expToQueue(6) expToClass(7)
OBJECT-TYPE    
  MlsQosMappingType  

sleMlsQosGlobalControlMappingIngValue 1.3.6.1.4.1.6296.101.28.1.2.8
Ingress or incoming mapping values. Based on sleMlsQosGlobalControlMappingType, this value has to be set. Ex. If sleMlsQosGlobalControlMappingType = cosToCos, then sleMlsQosGlobalControlMappingIngValue = Incoming or ingress COS value
OBJECT-TYPE    
  Integer32  

sleMlsQosGlobalControlMappingEgrValue 1.3.6.1.4.1.6296.101.28.1.2.9
Egress or outgoing mapping values. Based on sleMlsQosGlobalControlMappingType, this value has to be set. Ex. If sleMlsQosGlobalControlMappingType = cosToCos, then sleMlsQosGlobalControlMappingEgrValue = outgoing or egress COS value
OBJECT-TYPE    
  Integer32  

sleMlsQosGlobalControlQueueId 1.3.6.1.4.1.6296.101.28.1.2.10
Queue Id
OBJECT-TYPE    
  INTEGER  

sleMlsQosGlobalControlWrrQueueWeight 1.3.6.1.4.1.6296.101.28.1.2.11
Queue weight for weighted round robin scheduling. This value is set for the Queue Id configured via sleMlsQosGlobalControlQueueId
OBJECT-TYPE    
  INTEGER  

sleMlsQosGlobalControlCpuMaxPpsRate 1.3.6.1.4.1.6296.101.28.1.2.12
Rate limiting for CPU. Defines Max packets per second to CPU This value is set for the Queue Id configured via sleMlsQosGlobalControlQueueId
OBJECT-TYPE    
  INTEGER  

sleMlsQosGlobalControlCpuQueueWt 1.3.6.1.4.1.6296.101.28.1.2.13
Weight for CPU Queue. This value is set for the Queue Id configured via sleMlsQosGlobalControlQueueId
OBJECT-TYPE    
  INTEGER  

sleMlsQosGlobalControlNodeId 1.3.6.1.4.1.6296.101.28.1.2.14
Node Id
OBJECT-TYPE    
  INTEGER 0..4  

sleMlsQosGlobalControlMappingEgrClassValue 1.3.6.1.4.1.6296.101.28.1.2.15
Egress or outgoing mapping value is only for exp to class Diffserv class alias, eg: be, ef, af11 etc. If sleMlsQosGlobalControlMappingType is exp-to-class, this value has to be set. Ex. If sleMlsQosGlobalControlMappingType = exp-to-class, then sleMlsQosGlobalControlMappingEgrValue = outgoing or egress class value
OBJECT-TYPE    
  OCTET STRING  

sleMlsQosAggPolice 1.3.6.1.4.1.6296.101.28.2
OBJECT IDENTIFIER    

sleMlsQosAggPoliceTable 1.3.6.1.4.1.6296.101.28.2.1
Aggrgegate Policy Table
OBJECT-TYPE    
  SEQUENCE OF  
    SleMlsQosAggPoliceEntry

sleMlsQosAggPoliceEntry 1.3.6.1.4.1.6296.101.28.2.1.1
OBJECT-TYPE    
  SleMlsQosAggPoliceEntry  

sleMlsQosAggPoliceIndex 1.3.6.1.4.1.6296.101.28.2.1.1.1
Police index
OBJECT-TYPE    
  Integer32 1..65535  

sleMlsQosAggPoliceName 1.3.6.1.4.1.6296.101.28.2.1.1.2
Police Name
OBJECT-TYPE    
  OCTET STRING  

sleMlsQosAggPoliceTrafficRate 1.3.6.1.4.1.6296.101.28.2.1.1.3
Traffic Rate configured for the Aggregate police profile
OBJECT-TYPE    
  Integer32  

sleMlsQosAggPoliceBurstSize 1.3.6.1.4.1.6296.101.28.2.1.1.4
Burst Size configured for the Aggregate police profile
OBJECT-TYPE    
  Integer32  

sleMlsQosAggPoliceControl 1.3.6.1.4.1.6296.101.28.2.2
OBJECT IDENTIFIER    

sleMlsQosAggPoliceCtrlRequest 1.3.6.1.4.1.6296.101.28.2.2.1
the configuration commands, and user can configure functions via setting this entry as proper value.
OBJECT-TYPE    
  INTEGER createAggrPolice(1), deleteAggrPolice(2)  

sleMlsQosAggPoliceCtrlStatus 1.3.6.1.4.1.6296.101.28.2.2.2
status of user command. User have to check this value as .busy. or .idle. before do setRequest.
OBJECT-TYPE    
  SleControlStatusType  

sleMlsQosAggPoliceConfigCtrlTimer 1.3.6.1.4.1.6296.101.28.2.2.3
the wait-time until setRequest end. In case of short-time command, this value is 0
OBJECT-TYPE    
  Gauge32  

sleMlsQosAggPoliceCtrlTimeStamp 1.3.6.1.4.1.6296.101.28.2.2.4
the time stamp of the last command. (don.t care)
OBJECT-TYPE    
  TimeTicks  

sleMlsQosAggPoliceCtrlReqResult 1.3.6.1.4.1.6296.101.28.2.2.5
Result of the last command.
OBJECT-TYPE    
  SleControlRequestResultType  

sleMlsQosAggPoliceCtrlName 1.3.6.1.4.1.6296.101.28.2.2.6
Aggregator Police Name
OBJECT-TYPE    
  OCTET STRING  

sleMlsQosAggPoliceCtrlTrafficRate 1.3.6.1.4.1.6296.101.28.2.2.7
Traffic Rate configured for the Aggrgegate Police profile
OBJECT-TYPE    
  Integer32  

sleMlsQosAggPoliceCtrlBurstSize 1.3.6.1.4.1.6296.101.28.2.2.8
Traffic Rate configured for the Aggrgegate Police profile
OBJECT-TYPE    
  Integer32  

sleMlsQosACL 1.3.6.1.4.1.6296.101.28.3
OBJECT IDENTIFIER    

sleMlsQosACLTable 1.3.6.1.4.1.6296.101.28.3.1
OBJECT-TYPE    
  SEQUENCE OF  
    SleMlsQosACLEntry

sleMlsQosACLEntry 1.3.6.1.4.1.6296.101.28.3.1.1
OBJECT-TYPE    
  SleMlsQosACLEntry  

sleMlsQosACLIndex 1.3.6.1.4.1.6296.101.28.3.1.1.1
Index for the table. This is a running index number, which will be generated internally
OBJECT-TYPE    
  Integer32 1..65535  

sleMlsQosACLFilterIndex 1.3.6.1.4.1.6296.101.28.3.1.1.2
Filter Index for the table. This is a running index number, which will be generated internally
OBJECT-TYPE    
  Integer32 1..65535  

sleMlsQosACLName 1.3.6.1.4.1.6296.101.28.3.1.1.3
Access Control List Num. <1-99> standard access list <100-199> extended access list <1300-1999> standard access list (expanded range) <2000-2699> extended access list (expanded range) Name of the access list
OBJECT-TYPE    
  OCTET STRING  

sleMlsQosACLMatchType 1.3.6.1.4.1.6296.101.28.3.1.1.4
ACL MATCH Type mac (1), EthType(2), l3Proto (3)
OBJECT-TYPE    
  ACLMatchType  

sleMlsQosACLMatchAction 1.3.6.1.4.1.6296.101.28.3.1.1.5
ACL Actions deny(0) deny the packets permit(1) permit. remark(2) mark the packets
OBJECT-TYPE    
  ACLMatchActionType  

sleMlsQosACLEtherType 1.3.6.1.4.1.6296.101.28.3.1.1.6
ACL ethertype to be matched. ip4(0) ipv4 packets ip6(1) ipv6 packets. mpls(3) mpls packets
OBJECT-TYPE    
  ACLEtherType  

sleMlsQosACLL3Protocol 1.3.6.1.4.1.6296.101.28.3.1.1.7
ACL protocols to be matched. 0-255 : IANA protocol numbers 256 - any Some important protocol Numbers GRE - 47 IGMP -2 IPV4 - 4 IPComp - 108 OSPF - 89 RSVP - 46 PIM - 103 VRRP - 112
OBJECT-TYPE    
  Integer32 0..256  

sleMlsQosACLSrcIpAddress 1.3.6.1.4.1.6296.101.28.3.1.1.8
Src Ip Address
OBJECT-TYPE    
  OCTET STRING  

sleMlsQosACLDstIpAddress 1.3.6.1.4.1.6296.101.28.3.1.1.9
DST Address
OBJECT-TYPE    
  OCTET STRING  

sleMlsQosACLSrcIpAddrMask 1.3.6.1.4.1.6296.101.28.3.1.1.10
SRC Address Mask
OBJECT-TYPE    
  OCTET STRING  

sleMlsQosACLDstIpAddrMask 1.3.6.1.4.1.6296.101.28.3.1.1.11
DST Address Mask
OBJECT-TYPE    
  OCTET STRING  

sleMlsQosACLSrcMacAddress 1.3.6.1.4.1.6296.101.28.3.1.1.12
Src MAC Address
OBJECT-TYPE    
  OCTET STRING  

sleMlsQosACLDstMacAddress 1.3.6.1.4.1.6296.101.28.3.1.1.13
DST MAC Address
OBJECT-TYPE    
  OCTET STRING  

sleMlsQosACLSrcMacAddrMask 1.3.6.1.4.1.6296.101.28.3.1.1.14
SRC Address Mask
OBJECT-TYPE    
  OCTET STRING  

sleMlsQosACLDstMacAddrMask 1.3.6.1.4.1.6296.101.28.3.1.1.15
DST Address Mask
OBJECT-TYPE    
  OCTET STRING  

sleMlsQosACLTcpUdpSrcPortAction 1.3.6.1.4.1.6296.101.28.3.1.1.16
TCP/UDP Src port action 0 - no-action 1 - equal 2 - not-equal 3 - less-than 4 - Greater-than 5 - Range
OBJECT-TYPE    
  AclTcpUdpPortActionType  

sleMlsQosACLTcpUdpDstPortAction 1.3.6.1.4.1.6296.101.28.3.1.1.17
TCP/UDP Dst port action 0 - no-action 1 - equal 2 - not-equal 3 - less-than 4 - Greater-than 5 - Range
OBJECT-TYPE    
  AclTcpUdpPortActionType  

sleMlsQosACLTcpUdpSrcPort 1.3.6.1.4.1.6296.101.28.3.1.1.18
TCP/UDP Src port .
OBJECT-TYPE    
  Integer32  

sleMlsQosACLTcpUdpDstPort 1.3.6.1.4.1.6296.101.28.3.1.1.19
TCP/UDP Dst port .
OBJECT-TYPE    
  Integer32  

sleMlsQosACLNameSrcIpExactMatch 1.3.6.1.4.1.6296.101.28.3.1.1.20
Exact Match
OBJECT-TYPE    
  Integer32  

sleMlsQosACLActionRemarkDesc 1.3.6.1.4.1.6296.101.28.3.1.1.21
Remark Description
OBJECT-TYPE    
  OCTET STRING  

sleMlsQosACLIcmpType 1.3.6.1.4.1.6296.101.28.3.1.1.22
The object is used to display the ICMP type of control message Description Type Code echo-reply 0 0 net-unreachable 3 0 host-unreachable 3 1 protocol-unreachable 3 2 port-unreachable 3 3 packet-too-big 3 4 source-route-failed 3 5 network-unknown 3 6 host-unknown 3 7 host-isolated 3 8 dod-net-prohibited 3 9 dod-host-prohibited 3 10 net-tos-unreachable 3 11 host-tos-unreachable 3 12 administratively-prohibited 3 13 host-precedence-unreachable 3 14 precedence-unreachable 3 15 source-quench 4 0 net-redirect 5 0 host-redirect 5 1 net-tos-redirect 5 2 host-tos-redirect 5 3 alternate-address 6 -1 echo 8 0 router-advertisement 9 0 router-solicitation 10 0 time-exceeded 11 -1 ttl-exceeded 11 0 reassembly-timeout 11 1 parameter-problem 12 -1 no-room-for-option 12 0 option-missing 12 1 timestamp-request 13 0 timestamp-reply 14 0 information-request 15 0 information-reply 16 0 mask-request 17 0 mask-reply 18 0 traceroute 30 -1 conversion-error 31 -1 mobile-redirect 32 -1
OBJECT-TYPE    
  Integer32  

sleMlsQosACLIcmpCode 1.3.6.1.4.1.6296.101.28.3.1.1.23
The object is used to display the ICMP code of control message Description Type Code echo-reply 0 0 net-unreachable 3 0 host-unreachable 3 1 protocol-unreachable 3 2 port-unreachable 3 3 packet-too-big 3 4 source-route-failed 3 5 network-unknown 3 6 host-unknown 3 7 host-isolated 3 8 dod-net-prohibited 3 9 dod-host-prohibited 3 10 net-tos-unreachable 3 11 host-tos-unreachable 3 12 administratively-prohibited 3 13 host-precedence-unreachable 3 14 precedence-unreachable 3 15 source-quench 4 0 net-redirect 5 0 host-redirect 5 1 net-tos-redirect 5 2 host-tos-redirect 5 3 alternate-address 6 -1 echo 8 0 router-advertisement 9 0 router-solicitation 10 0 time-exceeded 11 -1 ttl-exceeded 11 0 reassembly-timeout 11 1 parameter-problem 12 -1 no-room-for-option 12 0 option-missing 12 1 timestamp-request 13 0 timestamp-reply 14 0 information-request 15 0 information-reply 16 0 mask-request 17 0 mask-reply 18 0 traceroute 30 -1 conversion-error 31 -1 mobile-redirect 32 -1
OBJECT-TYPE    
  Integer32  

sleMlsQosACLTcpUdpSrcPortEnd 1.3.6.1.4.1.6296.101.28.3.1.1.24
End port for TCP/UDP source port range.
OBJECT-TYPE    
  Integer32  

sleMlsQosACLTcpUdpDstPortEnd 1.3.6.1.4.1.6296.101.28.3.1.1.25
End port for TCP/UDP destination port range.
OBJECT-TYPE    
  Integer32  

sleMlsQosACLControl 1.3.6.1.4.1.6296.101.28.3.2
OBJECT IDENTIFIER    

sleMlsQosACLControlRequest 1.3.6.1.4.1.6296.101.28.3.2.1
the configuration commands, and user can configure functions via setting this entry as proper value.
OBJECT-TYPE    
  INTEGER setStandAclMatchSrcIp(1), unSetStandAclMatchSrcIp(2), setExtenAclMatchMac(3), unSetExtenAclMatchMac(4), setExtenAclMatchEthType(5), unSetExtenAclMatchEthType(6), setExtenAclMatchL3Proto(7), unSetExtenAclMatchL3Proto(8), setExtenAclMatchTcpUdp(9), unSetExtenAclMatchTcpUdp(10), setAclNameSrcIp(11), unSetAclNameSrcIp(12), setAclWithActionRemark(13), unSetAclWithActionRemark(14)  

sleMlsQosACLControlStatus 1.3.6.1.4.1.6296.101.28.3.2.2
status of user command. User have to check this value as .busy. or .idle. before do setRequest.
OBJECT-TYPE    
  SleControlStatusType  

sleMlsQosACLConfigControlTimer 1.3.6.1.4.1.6296.101.28.3.2.3
the wait-time until setRequest end. In case of short-time command, this value is 0
OBJECT-TYPE    
  Gauge32  

sleMlsQosACLControlTimeStamp 1.3.6.1.4.1.6296.101.28.3.2.4
the time stamp of the last command. (don.t care)
OBJECT-TYPE    
  TimeTicks  

sleMlsQosACLControlReqResult 1.3.6.1.4.1.6296.101.28.3.2.5
Result of the last command.
OBJECT-TYPE    
  SleControlRequestResultType  

sleMlsQosACLCtrlName 1.3.6.1.4.1.6296.101.28.3.2.6
Access Control List Name. <1-99> standard access list <100-199> extended access list <1300-1999> standard access list (expanded range) <2000-2699> extended access list (expanded range) Name for the access list
OBJECT-TYPE    
  OCTET STRING  

sleMlsQosACLCtrlMatchType 1.3.6.1.4.1.6296.101.28.3.2.7
ACL Match Types mac (1), EthType(2), l3Proto (3)
OBJECT-TYPE    
  ACLMatchType  

sleMlsQosACLCtrlMatchAction 1.3.6.1.4.1.6296.101.28.3.2.8
ACL Actions deny(0) deny the packets permit(1) Permit packets remark(2) mark the packets
OBJECT-TYPE    
  ACLMatchActionType  

sleMlsQosACLCtrlEtherType 1.3.6.1.4.1.6296.101.28.3.2.9
ACL MAC ethertype to be matched. WORD Ethertype value - (0x600-0xffff) ip4 IPv4 Ethertype - 0x0800 ip6 IPv6 Ethertype - 0x86dd mpls MPLS Ethertype - 0x8847
OBJECT-TYPE    
  ACLEtherType  

sleMlsQosACLCtrlL3Protocol 1.3.6.1.4.1.6296.101.28.3.2.10
ACL protocols to be matched. 0-255 : IANA protocol numbers 256 - any Some important protocol Numbers GRE - 47 IGMP -2 IPV4 - 4 IPComp - 108 OSPF - 89 RSVP - 46 PIM - 103 VRRP - 112
OBJECT-TYPE    
  Integer32 0..256  

sleMlsQosACLCtrlSrcAddress 1.3.6.1.4.1.6296.101.28.3.2.11
ACL SrcAddress. 1. MAC address 2. IP Address 3. Any
OBJECT-TYPE    
  OCTET STRING  

sleMlsQosACLCtrlDstAddress 1.3.6.1.4.1.6296.101.28.3.2.12
ACL SrcAddress. 1. MAC address 2. IP Address 3. Any
OBJECT-TYPE    
  OCTET STRING  

sleMlsQosACLCtrlSrcAddrMask 1.3.6.1.4.1.6296.101.28.3.2.13
ACL Src Addr Mask. 1. MAC address 2. IP Address
OBJECT-TYPE    
  OCTET STRING  

sleMlsQosACLCtrlDstAddrMask 1.3.6.1.4.1.6296.101.28.3.2.14
ACL dst Addr Mask. 1. MAC address 2. IP Address
OBJECT-TYPE    
  OCTET STRING  

sleMlsQosACLCtrlTcpUdpSrcPortAction 1.3.6.1.4.1.6296.101.28.3.2.15
TCP/UDP Port Action to be matched. 1 - equal 2 - not-equal 3 - less-than 4 - Greater-than 5 - Range
OBJECT-TYPE    
  AclTcpUdpPortActionType  

sleMlsQosACLCtrlTcpUdpDstPortAction 1.3.6.1.4.1.6296.101.28.3.2.16
TCP/UDP Port Action to be matched. 1 - equal 2 - not-equal 3 - less-than 4 - Greater-than 5 - Range
OBJECT-TYPE    
  AclTcpUdpPortActionType  

sleMlsQosACLCtrlTcpUdpSrcPort 1.3.6.1.4.1.6296.101.28.3.2.17
TCP/UDP Src port to be matched.
OBJECT-TYPE    
  Integer32  

sleMlsQosACLCtrlTcpUdpDstPort 1.3.6.1.4.1.6296.101.28.3.2.18
TCP/UDP Dst port to be matched.
OBJECT-TYPE    
  Integer32  

sleMlsQosACLCtrlAclNameExactMatch 1.3.6.1.4.1.6296.101.28.3.2.19
Configure Exact Match for Name
OBJECT-TYPE    
  Integer32  

sleMlsQosACLCtrlActionRemarkDesc 1.3.6.1.4.1.6296.101.28.3.2.20
Configure remark description
OBJECT-TYPE    
  OCTET STRING  

sleMlsQosACLCtrlIcmpType 1.3.6.1.4.1.6296.101.28.3.2.21
The object is used to set the ICMP type of control message Description Type Code echo-reply 0 0 net-unreachable 3 0 host-unreachable 3 1 protocol-unreachable 3 2 port-unreachable 3 3 packet-too-big 3 4 source-route-failed 3 5 network-unknown 3 6 host-unknown 3 7 host-isolated 3 8 dod-net-prohibited 3 9 dod-host-prohibited 3 10 net-tos-unreachable 3 11 host-tos-unreachable 3 12 administratively-prohibited 3 13 host-precedence-unreachable 3 14 precedence-unreachable 3 15 source-quench 4 0 net-redirect 5 0 host-redirect 5 1 net-tos-redirect 5 2 host-tos-redirect 5 3 alternate-address 6 -1 echo 8 0 router-advertisement 9 0 router-solicitation 10 0 time-exceeded 11 -1 ttl-exceeded 11 0 reassembly-timeout 11 1 parameter-problem 12 -1 no-room-for-option 12 0 option-missing 12 1 timestamp-request 13 0 timestamp-reply 14 0 information-request 15 0 information-reply 16 0 mask-request 17 0 mask-reply 18 0 traceroute 30 -1 conversion-error 31 -1 mobile-redirect 32 -1
OBJECT-TYPE    
  Integer32  

sleMlsQosACLCtrlIcmpCode 1.3.6.1.4.1.6296.101.28.3.2.22
The object is used to set the ICMP code of control message Description Type Code echo-reply 0 0 net-unreachable 3 0 host-unreachable 3 1 protocol-unreachable 3 2 port-unreachable 3 3 packet-too-big 3 4 source-route-failed 3 5 network-unknown 3 6 host-unknown 3 7 host-isolated 3 8 dod-net-prohibited 3 9 dod-host-prohibited 3 10 net-tos-unreachable 3 11 host-tos-unreachable 3 12 administratively-prohibited 3 13 host-precedence-unreachable 3 14 precedence-unreachable 3 15 source-quench 4 0 net-redirect 5 0 host-redirect 5 1 net-tos-redirect 5 2 host-tos-redirect 5 3 alternate-address 6 -1 echo 8 0 router-advertisement 9 0 router-solicitation 10 0 time-exceeded 11 -1 ttl-exceeded 11 0 reassembly-timeout 11 1 parameter-problem 12 -1 no-room-for-option 12 0 option-missing 12 1 timestamp-request 13 0 timestamp-reply 14 0 information-request 15 0 information-reply 16 0 mask-request 17 0 mask-reply 18 0 traceroute 30 -1 conversion-error 31 -1 mobile-redirect 32 -1
OBJECT-TYPE    
  Integer32  

sleMlsQosACLCtrlTcpUdpSrcPortEnd 1.3.6.1.4.1.6296.101.28.3.2.23
End port for TCP/UDP Src port range to be matched.
OBJECT-TYPE    
  Integer32  

sleMlsQosACLCtrlTcpUdpDstPortEnd 1.3.6.1.4.1.6296.101.28.3.2.24
End port for TCP/UDP Dst port range to be matched.
OBJECT-TYPE    
  Integer32  

sleMlsQosACLNotification 1.3.6.1.4.1.6296.101.28.3.3
OBJECT IDENTIFIER    

sleMlsQosClassMap 1.3.6.1.4.1.6296.101.28.4
OBJECT IDENTIFIER    

sleMlsQosClassMapTable 1.3.6.1.4.1.6296.101.28.4.1
OBJECT-TYPE    
  SEQUENCE OF  
    SleMlsQosClassMapEntry

sleMlsQosClassMapEntry 1.3.6.1.4.1.6296.101.28.4.1.1
OBJECT-TYPE    
  SleMlsQosClassMapEntry  

sleMlsQosClassMapName 1.3.6.1.4.1.6296.101.28.4.1.1.1
Index for the table. Class Map name
OBJECT-TYPE    
  OCTET STRING  

sleMlsQosClassMapMatchCosValue 1.3.6.1.4.1.6296.101.28.4.1.1.2
Class map Match criteria : Cos value
OBJECT-TYPE    
  Integer32  

sleMlsQosClassMapMatchInnerCosValue 1.3.6.1.4.1.6296.101.28.4.1.1.3
Class map Match criteria : Inner Cos value
OBJECT-TYPE    
  Integer32  

sleMlsQosClassMapMatchEgressInterface 1.3.6.1.4.1.6296.101.28.4.1.1.4
Class map Match criteria : Engress Interface
OBJECT-TYPE    
  OCTET STRING  

sleMlsQosClassMapMatchEtherType 1.3.6.1.4.1.6296.101.28.4.1.1.5
Class map Match criteria : Eth Type
OBJECT-TYPE    
  OCTET STRING  

sleMlsQosClassMapMatchSrcIpAddr 1.3.6.1.4.1.6296.101.28.4.1.1.6
Class map Match criteria : Src Ip Address
OBJECT-TYPE    
  OCTET STRING  

sleMlsQosClassMapMatchDstIpAddr 1.3.6.1.4.1.6296.101.28.4.1.1.7
Class map Match criteria : dst Ip Address
OBJECT-TYPE    
  OCTET STRING  

sleMlsQosClassMapMatchSrcIpMaskLen 1.3.6.1.4.1.6296.101.28.4.1.1.8
Class map Match criteria : Src Ip Mask Length
OBJECT-TYPE    
  Integer32  

sleMlsQosClassMapMatchDstIpMaskLen 1.3.6.1.4.1.6296.101.28.4.1.1.9
Class map Match criteria : Dst Ip Mask Length
OBJECT-TYPE    
  Integer32  

sleMlsQosClassMapMatchSrcIpV6Addr 1.3.6.1.4.1.6296.101.28.4.1.1.10
Class map Match criteria : Src Ip Address
OBJECT-TYPE    
  OCTET STRING  

sleMlsQosClassMapMatchDstIpV6Addr 1.3.6.1.4.1.6296.101.28.4.1.1.11
Class map Match criteria : dst Ip Address
OBJECT-TYPE    
  OCTET STRING  

sleMlsQosClassMapMatchSrcIpV6MaskLen 1.3.6.1.4.1.6296.101.28.4.1.1.12
Class map Match criteria : Src Ip Mask Length
OBJECT-TYPE    
  Integer32  

sleMlsQosClassMapMatchDstIpV6MaskLen 1.3.6.1.4.1.6296.101.28.4.1.1.13
Class map Match criteria : Dst Ip Mask Length
OBJECT-TYPE    
  Integer32  

sleMlsQosClassMapMatchIpDscp 1.3.6.1.4.1.6296.101.28.4.1.1.14
Class map Match criteria : DSCP value
OBJECT-TYPE    
  Integer32  

sleMlsQosClassMapMatchIpPrecedence 1.3.6.1.4.1.6296.101.28.4.1.1.15
Class map Match criteria : Ip Precedence
OBJECT-TYPE    
  Integer32  

sleMlsQosClassMapMatchIp6Dscp 1.3.6.1.4.1.6296.101.28.4.1.1.16
Class map Match criteria : Ip6 DSCP value
OBJECT-TYPE    
  Integer32  

sleMlsQosClassMapMatchIp6Precedence 1.3.6.1.4.1.6296.101.28.4.1.1.17
Class map Match criteria : ip6 Precedence value
OBJECT-TYPE    
  Integer32  

sleMlsQosClassMapMatchTcpSrcPort 1.3.6.1.4.1.6296.101.28.4.1.1.18
Class map Match criteria : TCP src Port
OBJECT-TYPE    
  OCTET STRING  

sleMlsQosClassMapMatchTcpDstPort 1.3.6.1.4.1.6296.101.28.4.1.1.19
Class map Match criteria : TCP Dst Port
OBJECT-TYPE    
  OCTET STRING  

sleMlsQosClassMapMatchTcpSrcPortRange 1.3.6.1.4.1.6296.101.28.4.1.1.20
Class map Match criteria : TCP src Port Range
OBJECT-TYPE    
  OCTET STRING  

sleMlsQosClassMapMatchTcpDstPortRange 1.3.6.1.4.1.6296.101.28.4.1.1.21
Class map Match criteria : TCP Dst Port Range
OBJECT-TYPE    
  OCTET STRING  

sleMlsQosClassMapMatchUdpSrcPort 1.3.6.1.4.1.6296.101.28.4.1.1.22
Class map Match criteria : UDP src Port
OBJECT-TYPE    
  OCTET STRING  

sleMlsQosClassMapMatchUdpDstPort 1.3.6.1.4.1.6296.101.28.4.1.1.23
Class map Match criteria : UDP Dst Port
OBJECT-TYPE    
  OCTET STRING  

sleMlsQosClassMapMatchUdpSrcPortRange 1.3.6.1.4.1.6296.101.28.4.1.1.24
Class map Match criteria : UDP src Port
OBJECT-TYPE    
  OCTET STRING  

sleMlsQosClassMapMatchUdpDstPortRange 1.3.6.1.4.1.6296.101.28.4.1.1.25
Class map Match criteria : UDP Dst Port
OBJECT-TYPE    
  OCTET STRING  

sleMlsQosClassMapMatchSrcMacAddr 1.3.6.1.4.1.6296.101.28.4.1.1.26
Class map Match criteria : Src MAC Addr
OBJECT-TYPE    
  OCTET STRING  

sleMlsQosClassMapMatchSrcMacMask 1.3.6.1.4.1.6296.101.28.4.1.1.27
Class map Match criteria : Src MAC Addr Mask
OBJECT-TYPE    
  OCTET STRING  

sleMlsQosClassMapMatchDstMacAddr 1.3.6.1.4.1.6296.101.28.4.1.1.28
Class map Match criteria : Dst MAC Addr
OBJECT-TYPE    
  OCTET STRING  

sleMlsQosClassMapMatchDstMacMask 1.3.6.1.4.1.6296.101.28.4.1.1.29
Class map Match criteria : Dst MAC Addr Mask
OBJECT-TYPE    
  OCTET STRING  

sleMlsQosClassMapMatchVlanId 1.3.6.1.4.1.6296.101.28.4.1.1.30
Class map Match criteria : Vlan Id
OBJECT-TYPE    
  OCTET STRING  

sleMlsQosClassMapMatchVlanIdRange 1.3.6.1.4.1.6296.101.28.4.1.1.31
Class map Match criteria : Vlan Id Range
OBJECT-TYPE    
  OCTET STRING  

sleMlsQosClassMapMatchInnerVlanId 1.3.6.1.4.1.6296.101.28.4.1.1.32
Class map Match criteria : Inner Vlan Id
OBJECT-TYPE    
  Integer32  

sleMlsQosClassMapMatchVlanTpid 1.3.6.1.4.1.6296.101.28.4.1.1.33
Class map Match criteria : Vlan TPID
OBJECT-TYPE    
  OCTET STRING  

sleMlsQosClassMapMatchAccessGroup 1.3.6.1.4.1.6296.101.28.4.1.1.34
Class map Match criteria : Acl Name
OBJECT-TYPE    
  OCTET STRING  

sleMlsQosClassMapMatchLayer4SrcPort 1.3.6.1.4.1.6296.101.28.4.1.1.35
Class map Match criteria : Layer4 Any Src Port
OBJECT-TYPE    
  OCTET STRING  

sleMlsQosClassMapMatchLayer4DstPort 1.3.6.1.4.1.6296.101.28.4.1.1.36
Class map Match criteria : Layer4 Any Dst Port
OBJECT-TYPE    
  OCTET STRING  

sleMlsQosClassMapMatchLayer4SrcPortRange 1.3.6.1.4.1.6296.101.28.4.1.1.37
Class map Match criteria : Layer4 Any src Port range
OBJECT-TYPE    
  OCTET STRING  

sleMlsQosClassMapMatchLayer4DstPortRange 1.3.6.1.4.1.6296.101.28.4.1.1.38
Class map Match criteria : Layer4 Any Dst Port range
OBJECT-TYPE    
  OCTET STRING  

sleMplsQosClassMapMatchCriteria 1.3.6.1.4.1.6296.101.28.4.1.1.39
This object is used to set the Class map match criteria, to map the matchAll or MatchAny for HQS.
OBJECT-TYPE    
  INTEGER noMatch(0), matchAll(1), matchAny(2)  

sleMlsQosClassMapControl 1.3.6.1.4.1.6296.101.28.4.2
OBJECT IDENTIFIER    

sleMlsQosClassMapControlRequest 1.3.6.1.4.1.6296.101.28.4.2.1
the configuration commands, and user can configure functions via setting this entry as proper value.
OBJECT-TYPE    
  INTEGER createClassMap(1), deleteClassMap(2), setClassMapMatch(3), unSetClassMapMatch(4), setClassMapMatchRange(5), unSetClassMapMatchRange(6), setClassMapMatchEtherType(7), unSetClassMapMatchEtherType(8), setClassMapMatchIpAddr(9), unSetClassMapMatchIpAddr(10), setClassMapMatchMac(11), unSetClassMapMatchMac(12), setClassMapMatchVlanTpid(13), unSetClassMapMatchVlanTpid(14), setClassMapMatchAccessGroup(15), unSetClassMapMatchAccessGroup(16), setClassMapMatchEgressIntf(17), unSetClassMapMatchEgressIntf(18)  

sleMlsQosClassMapControlStatus 1.3.6.1.4.1.6296.101.28.4.2.2
status of user command. User have to check this value as .busy. or .idle. before do setRequest.
OBJECT-TYPE    
  SleControlStatusType  

sleMlsQosClassMapControlTimer 1.3.6.1.4.1.6296.101.28.4.2.3
the wait-time until setRequest end. In case of short-time command, this value is 0
OBJECT-TYPE    
  Gauge32  

sleMlsQosClassMapontrolTimeStamp 1.3.6.1.4.1.6296.101.28.4.2.4
the time stamp of the last command. (don.t care)
OBJECT-TYPE    
  TimeTicks  

sleMlsQosClassMapControlReqResult 1.3.6.1.4.1.6296.101.28.4.2.5
Result of the last command.
OBJECT-TYPE    
  SleControlRequestResultType  

sleMlsQosClassMapCtrlName 1.3.6.1.4.1.6296.101.28.4.2.6
Class Map name
OBJECT-TYPE    
  OCTET STRING  

sleMlsQosClassMapCtrlMatchType 1.3.6.1.4.1.6296.101.28.4.2.7
Class Map Type cos (1) , innerCos(2), ipDscp (3), ipPrecedence (4), ip6Dscp (5), ip6Precedence (6), tcpSrcPort (7), tcpDstPort (8), udpSrcPort (9), udpDstPort (10), VlanId (11), innerVlanId (12), layer4SrcPort (13), layer4DstPort (14)
OBJECT-TYPE    
  ClassMapMatchType  

sleMlsQosClassMapCtrlMatchVal 1.3.6.1.4.1.6296.101.28.4.2.8
Class Map match Value
OBJECT-TYPE    
  Integer32  

sleMlsQosClassMapCtrlMatchRangeType 1.3.6.1.4.1.6296.101.28.4.2.9
Class Map Type tcpSrcPort (1), tcpDstPort (2), udpSrcPort (3), udpDstPort (4), VlanId (5), layer4SrcPort (6), layer4DstPort (7)
OBJECT-TYPE    
  ClassMapMatchRangeType  

sleMlsQosClassMapCtrlMatchRangeLow 1.3.6.1.4.1.6296.101.28.4.2.10
Class Map match Value: Low
OBJECT-TYPE    
  Integer32  

sleMlsQosClassMapCtrlMatchRangeHigh 1.3.6.1.4.1.6296.101.28.4.2.11
Class Map match Value : High
OBJECT-TYPE    
  Integer32  

sleMlsQosClassMapCtrlMatchEtherType 1.3.6.1.4.1.6296.101.28.4.2.12
Class map Match criteria : Eth Type
OBJECT-TYPE    
  OCTET STRING  

sleMlsQosClassMapCtrlMatchSrcType 1.3.6.1.4.1.6296.101.28.4.2.13
Class Map Src Type 1. IPv4 2. IPv6 3. Mac
OBJECT-TYPE    
  INTEGER ipv4(1), ipv6(2), mac(3)  

sleMlsQosClassMapCtrlMatchSrcAddr 1.3.6.1.4.1.6296.101.28.4.2.14
Class map Match criteria : Src Address. It can be IPV4 / IPV6 / MAC
OBJECT-TYPE    
  OCTET STRING  

sleMlsQosClassMapCtrlMatchDstAddr 1.3.6.1.4.1.6296.101.28.4.2.15
Class map Match criteria : dst Ip Address it can be IPV4 / IPV6 / MAC
OBJECT-TYPE    
  OCTET STRING  

sleMlsQosClassMapCtrlMatchSrcIpMaskLen 1.3.6.1.4.1.6296.101.28.4.2.16
Class map Match criteria : Src Ip Mask Length
OBJECT-TYPE    
  Integer32  

sleMlsQosClassMapCtrlMatchDstIpMaskLen 1.3.6.1.4.1.6296.101.28.4.2.17
Class map Match criteria : Dst Ip Mask Length
OBJECT-TYPE    
  Integer32  

sleMlsQosClassMapCtrlMatchSrcMacMask 1.3.6.1.4.1.6296.101.28.4.2.18
Class map Match criteria : Src MAC Addr Mask
OBJECT-TYPE    
  OCTET STRING  

sleMlsQosClassMapCtrlMatchDstMacMask 1.3.6.1.4.1.6296.101.28.4.2.19
Class map Match criteria : Dst MAC Addr Mask
OBJECT-TYPE    
  OCTET STRING  

sleMlsQosClassMapCtrlMatchAcessGroup 1.3.6.1.4.1.6296.101.28.4.2.20
Class map Match criteria : ACL Group List
OBJECT-TYPE    
  OCTET STRING  

sleMlsQosClassMapCtrlMatchVlanTpid 1.3.6.1.4.1.6296.101.28.4.2.21
Class map Match criteria : vlan TDID
OBJECT-TYPE    
  OCTET STRING  

sleMlsQosClassMapCtrlMatchEgressInterface 1.3.6.1.4.1.6296.101.28.4.2.22
Class map Match criteria : egress interface. This can be CPU, interface Name, Vlan Interface
OBJECT-TYPE    
  OCTET STRING  

sleMplsQosClassMapCtrlMatchCriteria 1.3.6.1.4.1.6296.101.28.4.2.23
This object is used to set the Class map match criteria, to map the matchAll or MatchAny for HQS.
OBJECT-TYPE    
  INTEGER matchAll(1), matchAny(2)  

sleMlsQosClassMapNotification 1.3.6.1.4.1.6296.101.28.4.3
OBJECT IDENTIFIER    

sleMlsQosPolicyMap 1.3.6.1.4.1.6296.101.28.5
OBJECT IDENTIFIER    

sleMlsQosPolicyMapTable 1.3.6.1.4.1.6296.101.28.5.1
OBJECT-TYPE    
  SEQUENCE OF  
    SleMlsQosPolicyMapEntry

sleMlsQosPolicyMapEntry 1.3.6.1.4.1.6296.101.28.5.1.1
OBJECT-TYPE    
  SleMlsQosPolicyMapEntry  

sleMlsQosPmapName 1.3.6.1.4.1.6296.101.28.5.1.1.1
Policy Map name
OBJECT-TYPE    
  OCTET STRING  

sleMlsQosPmapClassName 1.3.6.1.4.1.6296.101.28.5.1.1.2
Class map Name
OBJECT-TYPE    
  OCTET STRING  

sleMlsQosPmapClassMatchPriority 1.3.6.1.4.1.6296.101.28.5.1.1.3
Priority low(0) medium(1) high(2) highest(3)
OBJECT-TYPE    
  PmapPriorityType  

sleMlsQosPmapClassOperMode 1.3.6.1.4.1.6296.101.28.5.1.1.4
Operation Mode
OBJECT-TYPE    
  INTEGER none(0), allow(1), deny(2)  

sleMlsQosPmapClassPoliceType 1.3.6.1.4.1.6296.101.28.5.1.1.5
Police Type srtcm(1) trtcm(2)
OBJECT-TYPE    
  PmapPoliceType  

sleMlsQosPmapClassPoliceCIR 1.3.6.1.4.1.6296.101.28.5.1.1.6
Police CIR (committed ingress rate) value
OBJECT-TYPE    
  Integer32  

sleMlsQosPmapClassPolicePIR 1.3.6.1.4.1.6296.101.28.5.1.1.7
Police PIR (peak ingress rate) value
OBJECT-TYPE    
  Integer32  

sleMlsQosPmapClassPoliceCBS 1.3.6.1.4.1.6296.101.28.5.1.1.8
Police CBS (committed burst size) value
OBJECT-TYPE    
  Integer32  

sleMlsQosPmapClassPoliceEBS 1.3.6.1.4.1.6296.101.28.5.1.1.9
Police EBS (Excess burst size) value
OBJECT-TYPE    
  Integer32  

sleMlsQosPmapClassPoliceExdAction 1.3.6.1.4.1.6296.101.28.5.1.1.10
Exceed Action Type none (0) drop (1) set-dscp-transmit (2) set-tos-transmit (3) set-cos-transmit (4) transmit (7)
OBJECT-TYPE    
  PmapExceedActionType  

sleMlsQosPmapClassPoliceExdActionCos 1.3.6.1.4.1.6296.101.28.5.1.1.11
Exceed Action COS
OBJECT-TYPE    
  Integer32  

sleMlsQosPmapClassPoliceExdActionDscp 1.3.6.1.4.1.6296.101.28.5.1.1.12
Exceed Action DSCP
OBJECT-TYPE    
  Integer32  

sleMlsQosPmapClassPoliceExdActionTos 1.3.6.1.4.1.6296.101.28.5.1.1.13
Exceed Action TOS
OBJECT-TYPE    
  Integer32  

sleMlsQosPmapClassPoliceExdActionViolateAction 1.3.6.1.4.1.6296.101.28.5.1.1.14
Violate Action Type none(0) drop(1) set-dscp-transmit(2) set-cos-transmit(3) set-tos-transmit(4) transmit(5)
OBJECT-TYPE    
  PmapViolateActionType  

sleMlsQosPmapClassPoliceExdActionViolateValue 1.3.6.1.4.1.6296.101.28.5.1.1.15
Violate Action Value
OBJECT-TYPE    
  Integer32  

sleMlsQosPmapClassPoliceAggregateName 1.3.6.1.4.1.6296.101.28.5.1.1.16
Agrregate Police name:
OBJECT-TYPE    
  OCTET STRING  

sleMlsQosPmapClassSetActionDeny 1.3.6.1.4.1.6296.101.28.5.1.1.17
Action Type: deny
OBJECT-TYPE    
  Integer32  

sleMlsQosPmapClassSetActionCos 1.3.6.1.4.1.6296.101.28.5.1.1.18
Cos value
OBJECT-TYPE    
  Integer32  

sleMlsQosPmapClassSetActionCpuCos 1.3.6.1.4.1.6296.101.28.5.1.1.19
cpy Cos value.
OBJECT-TYPE    
  Integer32  

sleMlsQosPmapClassSetActionIpDscp 1.3.6.1.4.1.6296.101.28.5.1.1.20
Ip DSCP value .
OBJECT-TYPE    
  Integer32  

sleMlsQosPmapClassSetActionIp6Dscp 1.3.6.1.4.1.6296.101.28.5.1.1.21
Ip6 DSCP value to be set.
OBJECT-TYPE    
  Integer32  

sleMlsQosPmapClassSetActionIpPrecedence 1.3.6.1.4.1.6296.101.28.5.1.1.22
Ip precedence value to be set.
OBJECT-TYPE    
  Integer32  

sleMlsQosPmapClassSetActionIp6Precedence 1.3.6.1.4.1.6296.101.28.5.1.1.23
Ip6 precedence value to be set.
OBJECT-TYPE    
  Integer32  

sleMlsQosPmapClassSetActionMirrorToPortVal 1.3.6.1.4.1.6296.101.28.5.1.1.24
Mirror to Port value.
OBJECT-TYPE    
  OCTET STRING  

sleMlsQosPmapClassSetActionRedirectToPortVal 1.3.6.1.4.1.6296.101.28.5.1.1.25
redirect to Port value.
OBJECT-TYPE    
  OCTET STRING  

sleMlsQosPmapClassSetActionVlanId 1.3.6.1.4.1.6296.101.28.5.1.1.26
Vlan Id value.
OBJECT-TYPE    
  Integer32  

sleMlsQosPmapClassSetActionVlanCos 1.3.6.1.4.1.6296.101.28.5.1.1.27
Vlan COS value
OBJECT-TYPE    
  Integer32  

sleMlsQosPmapClassSetActionQosGroup 1.3.6.1.4.1.6296.101.28.5.1.1.28
Heirarchical qos policy-map qos-group. Max range is 1 to 2000.
OBJECT-TYPE    
  INTEGER  

sleMplsQosPmapClassSetActionQueue 1.3.6.1.4.1.6296.101.28.5.1.1.29
Internal Queue Priority.
OBJECT-TYPE    
  INTEGER 0..7  

sleMplsQosPmapClassSetActionCopyCpu 1.3.6.1.4.1.6296.101.28.5.1.1.30
Copy to CPU.
OBJECT-TYPE    
  INTEGER  

sleMlsQosPolicyMapControl 1.3.6.1.4.1.6296.101.28.5.2
OBJECT IDENTIFIER    

sleMlsQosPolicyMapControlRequest 1.3.6.1.4.1.6296.101.28.5.2.1
the configuration commands, and user can configure functions via setting this entry as proper value.
OBJECT-TYPE    
  INTEGER createPolicyMapClass(1), deletePolicyMapClass(2), setPolicyMapClassMatchPriority(3), setPolicyMapClassOperMode(4), unSetPolicyMapClassOperMode(5), setPolicyMapClassPolicer(6), unSetPolicyMapClassPolicer(7), setPolicyMapClassPolicerAggregate(8), unSetPolicyMapClassPolicerAggregate(9), setPolicyMapClassSet(10), unSetPolicyMapClassSet(11), deletePolicyMap(12)  

sleMlsQosPolicyMapControlStatus 1.3.6.1.4.1.6296.101.28.5.2.2
status of user command. User have to check this value as .busy. or .idle. before do setRequest.
OBJECT-TYPE    
  SleControlStatusType  

sleMlsQosPolicyMapControlTimer 1.3.6.1.4.1.6296.101.28.5.2.3
the wait-time until setRequest end. In case of short-time command, this value is 0
OBJECT-TYPE    
  Gauge32  

sleMlsQosPolicyMapontrolTimeStamp 1.3.6.1.4.1.6296.101.28.5.2.4
the time stamp of the last command. (don.t care)
OBJECT-TYPE    
  TimeTicks  

sleMlsQosPolicyMapControlReqResult 1.3.6.1.4.1.6296.101.28.5.2.5
Result of the last command.
OBJECT-TYPE    
  SleControlRequestResultType  

sleMlsQosPolicyMapCtrlName 1.3.6.1.4.1.6296.101.28.5.2.6
Index for the table. Class Map name
OBJECT-TYPE    
  OCTET STRING  

sleMlsQosPolicyMapCtrlClassName 1.3.6.1.4.1.6296.101.28.5.2.7
Class map Name
OBJECT-TYPE    
  OCTET STRING  

sleMlsQosPolicyMapCtrlClassMatchPriority 1.3.6.1.4.1.6296.101.28.5.2.8
Priority low(0) medium(1) high(2) highest(3)
OBJECT-TYPE    
  PmapPriorityType  

sleMlsQosPolicyMapCtrlClassOperMode 1.3.6.1.4.1.6296.101.28.5.2.9
Operation Mode
OBJECT-TYPE    
  INTEGER none(0), allow(1), deny(2)  

sleMlsQosPolicyMapCtrlClassPoliceType 1.3.6.1.4.1.6296.101.28.5.2.10
Police Type srtcm(1) trtcm(2)
OBJECT-TYPE    
  PmapPoliceType  

sleMlsQosPolicyMapCtrlClassPoliceCIR 1.3.6.1.4.1.6296.101.28.5.2.11
Police CIR (committed ingress rate) value
OBJECT-TYPE    
  Integer32  

sleMlsQosPolicyMapCtrlClassPolicePIR 1.3.6.1.4.1.6296.101.28.5.2.12
Police PIR (Peak ingress rate) value
OBJECT-TYPE    
  Integer32  

sleMlsQosPolicyMapCtrlClassPoliceCBS 1.3.6.1.4.1.6296.101.28.5.2.13
Police CBS (Committed Burst size) value
OBJECT-TYPE    
  Integer32  

sleMlsQosPolicyMapCtrlClassPoliceEBS 1.3.6.1.4.1.6296.101.28.5.2.14
Police EBS (Excess Burst size) value
OBJECT-TYPE    
  Integer32  

sleMlsQosPolicyMapCtrlClassPoliceExdAction 1.3.6.1.4.1.6296.101.28.5.2.15
Exceed Action Type none (0) drop (1) set-dscp-transmit (2) set-tos-transmit (3) set-cos-transmit (4) transmit (7)
OBJECT-TYPE    
  PmapExceedActionType  

sleMlsQosPolicyMapCtrlClassPoliceExdActionCos 1.3.6.1.4.1.6296.101.28.5.2.16
Exceed Action COS
OBJECT-TYPE    
  Integer32  

sleMlsQosPolicyMapCtrlClassPoliceExdActionDscp 1.3.6.1.4.1.6296.101.28.5.2.17
Exceed Action DSCP
OBJECT-TYPE    
  Integer32  

sleMlsQosPolicyMapCtrlClassPoliceExdActionTos 1.3.6.1.4.1.6296.101.28.5.2.18
Exceed Action TOS
OBJECT-TYPE    
  Integer32  

sleMlsQosPolicyMapCtrlClassPoliceExdActionViolateAction 1.3.6.1.4.1.6296.101.28.5.2.19
Exceed Action Violate none(0) drop(1) set-dscp-transmit(2) set-cos-transmit(3) set-tos-transmit(4) transmit(5)
OBJECT-TYPE    
  PmapViolateActionType  

sleMlsQosPolicyMapCtrlClassPoliceExdActionViolateValue 1.3.6.1.4.1.6296.101.28.5.2.20
Exceed Action Violate Value
OBJECT-TYPE    
  Integer32  

sleMlsQosPolicyMapCtrlClassPoliceAggregateName 1.3.6.1.4.1.6296.101.28.5.2.21
Aggregate Policy name: this is configured via sleMlsQosAggPoliceTable
OBJECT-TYPE    
  OCTET STRING  

sleMlsQosPolicyMapCtrlClassSetAction 1.3.6.1.4.1.6296.101.28.5.2.22
Action Types: cos (1), cpu-cos (2), ip-dscp (3), ip-precedence (4), redirect-to-port (5), mirror-to-port (6), vlan (7), ip6-dscp (8), ip6-precedence (9), cpu-copy (10), deny (11), qos-group(12), none(13), queue(14), vlan-cos(15)
OBJECT-TYPE    
  PmapSetActionType  

sleMlsQosPolicyMapCtrlClassSetActionCos 1.3.6.1.4.1.6296.101.28.5.2.23
Cos value to be set. This object is dependent on sleMlsQosPolicyMapCtrlClassSetAction. To set this value, sleMlsQosPolicyMapCtrlClassSetAction should be set as cos
OBJECT-TYPE    
  Integer32  

sleMlsQosPolicyMapCtrlClassSetActionCpuCos 1.3.6.1.4.1.6296.101.28.5.2.24
cpy Cos value to be set. This object is dependent on sleMlsQosPolicyMapCtrlClassSetAction. To set this value, sleMlsQosPolicyMapCtrlClassSetAction should be set as cpu-cos
OBJECT-TYPE    
  Integer32  

sleMlsQosPolicyMapCtrlClassSetActionIpDscp 1.3.6.1.4.1.6296.101.28.5.2.25
Ip DSCP value to be set. This object is dependent on sleMlsQosPolicyMapCtrlClassSetAction. To set this value, sleMlsQosPolicyMapCtrlClassSetAction should be set as ip-dscp
OBJECT-TYPE    
  Integer32  

sleMlsQosPolicyMapCtrlClassSetActionIp6Dscp 1.3.6.1.4.1.6296.101.28.5.2.26
Ip6 DSCP value to be set. This object is dependent on sleMlsQosPolicyMapCtrlClassSetAction. To set this value, sleMlsQosPolicyMapCtrlClassSetAction should be set as ip6-dscp
OBJECT-TYPE    
  Integer32  

sleMlsQosPolicyMapCtrlClassSetActionIpPrecedence 1.3.6.1.4.1.6296.101.28.5.2.27
Ip precedence value to be set. This object is dependent on sleMlsQosPolicyMapCtrlClassSetAction. To set this value, sleMlsQosPolicyMapCtrlClassSetAction should be set as ip-precedence
OBJECT-TYPE    
  Integer32  

sleMlsQosPolicyMapCtrlClassSetActionIp6Precedence 1.3.6.1.4.1.6296.101.28.5.2.28
Ip6 precedence value to be set. This object is dependent on sleMlsQosPolicyMapCtrlClassSetAction. To set this value, sleMlsQosPolicyMapCtrlClassSetAction should be set as ip6-precedence
OBJECT-TYPE    
  Integer32  

sleMlsQosPolicyMapCtrlClassSetActionMirrorToPort 1.3.6.1.4.1.6296.101.28.5.2.29
Mirror to Port value. This object is dependent on sleMlsQosPolicyMapCtrlClassSetAction. To setthis value, sleMlsQosPolicyMapCtrlClassSetAction should be set as mirror-to-port
OBJECT-TYPE    
  OCTET STRING  

sleMlsQosPolicyMapCtrlClassSetActionRedirectToPort 1.3.6.1.4.1.6296.101.28.5.2.30
redirect to Port value. This object is dependent on sleMlsQosPolicyMapCtrlClassSetAction. To setthis value, sleMlsQosPolicyMapCtrlClassSetAction should be set as redirect-to-port
OBJECT-TYPE    
  OCTET STRING  

sleMlsQosPolicyMapCtrlClassSetActionVlanId 1.3.6.1.4.1.6296.101.28.5.2.31
Vlan Id value. This object is dependent on sleMlsQosPolicyMapCtrlClassSetAction. To set this value, sleMlsQosPolicyMapCtrlClassSetAction should be set as vlan
OBJECT-TYPE    
  Integer32  

sleMlsQosPolicyMapCtrlClassSetActionVlanCos 1.3.6.1.4.1.6296.101.28.5.2.32
Vlan COS value
OBJECT-TYPE    
  Integer32  

sleMlsQosPolicyMapCtrlClassSetActionQosGroup 1.3.6.1.4.1.6296.101.28.5.2.33
Heirarchical qos policy-map qos-group. Max range is 1 to 2000.
OBJECT-TYPE    
  INTEGER  

sleMlsQosPolicyMapCtrlClassSetActionQueue 1.3.6.1.4.1.6296.101.28.5.2.34
Internal Queue Priority.
OBJECT-TYPE    
  INTEGER 0..7  

sleMlsQosInterface 1.3.6.1.4.1.6296.101.28.6
OBJECT IDENTIFIER    

sleMlsQosInterfaceTable 1.3.6.1.4.1.6296.101.28.6.1
Interface table
OBJECT-TYPE    
  SEQUENCE OF  
    SleMlsQosInterfaceEntry

sleMlsQosInterfaceEntry 1.3.6.1.4.1.6296.101.28.6.1.1
OBJECT-TYPE    
  SleMlsQosInterfaceEntry  

sleMlsQosInterfaceIndex 1.3.6.1.4.1.6296.101.28.6.1.1.1
This Index is based on Max entries i.e. 64 (dscp)
OBJECT-TYPE    
  Integer32 1..64  

sleMlsQosInterfaceName 1.3.6.1.4.1.6296.101.28.6.1.1.2
Index for the table. Interface Name
OBJECT-TYPE    
  OCTET STRING  

sleMlsQosInterfaceTrustState 1.3.6.1.4.1.6296.101.28.6.1.1.3
Interface trust state none (0) cos (1) dscp (2)
OBJECT-TYPE    
  MlsQosIntfTrustState  

sleMlsQosInterfaceCos 1.3.6.1.4.1.6296.101.28.6.1.1.4
Interface Cos value
OBJECT-TYPE    
  Integer32  

sleMlsQosInterfaceCosOverride 1.3.6.1.4.1.6296.101.28.6.1.1.5
Interface Cos override value
OBJECT-TYPE    
  Integer32  

sleMlsQosInterfaceCosToCos 1.3.6.1.4.1.6296.101.28.6.1.1.6
Interface Cos to cos mapping
OBJECT-TYPE    
  OCTET STRING  

sleMlsQosInterfaceCosToQueue 1.3.6.1.4.1.6296.101.28.6.1.1.7
Interface Cos to queue mapping
OBJECT-TYPE    
  OCTET STRING  

sleMlsQosInterfaceDscp 1.3.6.1.4.1.6296.101.28.6.1.1.8
Interface DSCP values
OBJECT-TYPE    
  Integer32  

sleMlsQosInterfaceDscpToDscp 1.3.6.1.4.1.6296.101.28.6.1.1.9
Interface dscp to dscp mapping
OBJECT-TYPE    
  OCTET STRING  

sleMlsQosInterfaceDscpToQueue 1.3.6.1.4.1.6296.101.28.6.1.1.10
Interface dscp to queue mapping
OBJECT-TYPE    
  OCTET STRING  

sleMlsQosInterfaceExpToExp 1.3.6.1.4.1.6296.101.28.6.1.1.11
Interface exp to exp mapping
OBJECT-TYPE    
  OCTET STRING  

sleMlsQosInterfaceTrafficShapeRate 1.3.6.1.4.1.6296.101.28.6.1.1.12
Interface Traffic Shaping rate
OBJECT-TYPE    
  Integer32  

sleMlsQosInterfaceTrafficShapeBurst 1.3.6.1.4.1.6296.101.28.6.1.1.13
Interface traffic shaping burst
OBJECT-TYPE    
  Integer32  

sleMlsQosInterfaceInputPolicyMap 1.3.6.1.4.1.6296.101.28.6.1.1.14
Interface policy map mapping
OBJECT-TYPE    
  OCTET STRING  

sleMlsQosInterfaceOutputPolicyMap 1.3.6.1.4.1.6296.101.28.6.1.1.15
OBJECT-TYPE    
  OCTET STRING  

sleMlsQosInterfaceTrustPassthroughCos 1.3.6.1.4.1.6296.101.28.6.1.1.16
Interface trust pass-through COS enabled
OBJECT-TYPE    
  Integer32  

sleMlsQosInterfaceTrustPassthroughDscp 1.3.6.1.4.1.6296.101.28.6.1.1.17
Interface trust pass-through DSCP enabled
OBJECT-TYPE    
  Integer32  

sleHQosInterfaceCosToClass 1.3.6.1.4.1.6296.101.28.6.1.1.18
Interface cos to class mapping in no truct mode It represnet COS - CNG - CLASS
OBJECT-TYPE    
  OCTET STRING  

sleHQosInterfaceDscpToClass 1.3.6.1.4.1.6296.101.28.6.1.1.19
Interface dscp to class mapping in no truct mode It represnet DSCP - CLASS
OBJECT-TYPE    
  OCTET STRING  

sleHQosInterfaceReplace 1.3.6.1.4.1.6296.101.28.6.1.1.20
To rewite the dscp/cos at egress in uniform mode.
OBJECT-TYPE    
  INTEGER none(0), cos(1), dscp(2)  

sleMlsQosInterfaceTrafficIfgExclude 1.3.6.1.4.1.6296.101.28.6.1.1.21
Interface traffic IFG exclude 0 - No 1 - Yes
OBJECT-TYPE    
  Integer32  

sleMlsQosInterfaceTrafficPolicingRate 1.3.6.1.4.1.6296.101.28.6.1.1.22
Interface traffic policing rate <8-1000000> in kbps
OBJECT-TYPE    
  Integer32  

sleMlsQosInterfaceTrafficPolicingBurst 1.3.6.1.4.1.6296.101.28.6.1.1.23
Interface traffic policing burst <2-2000>
OBJECT-TYPE    
  Integer32  

sleMlsQosInterfaceControl 1.3.6.1.4.1.6296.101.28.6.2
OBJECT IDENTIFIER    

sleMlsQosInterfaceControlRequest 1.3.6.1.4.1.6296.101.28.6.2.1
the configuration commands, and user can configure functions via setting this entry as proper value.
OBJECT-TYPE    
  INTEGER setInterfaceQosMapping(1), unSetInterfaceQosMapping(2), setInterfaceTrafficShaping(3), unSetInterfaceTrafficShaping(4), setInterfaceInputPolicyMap(5), unSetInterfaceInputPolicyMap(6), setInterfaceOutputPolicyMap(7), unSetInterfaceOutputPolicyMap(8), setInterfaceOveride(9), unsetInterfaceOveride(10), setInterfaceReplace(11), unsetInterfaceReplace(12), setInterfaceTrafficIfgExclude(13), unsetInterfaceTrafficIfgExclude(14), setInterfaceTrafficPolicingDot3x(15), unsetInterfaceTrafficPolicingDot3x(16)  

sleMlsQosInterfaceControlStatus 1.3.6.1.4.1.6296.101.28.6.2.2
status of user command. User have to check this value as .busy. or .idle. before do setRequest.
OBJECT-TYPE    
  SleControlStatusType  

sleMlsQosInterfaceControlTimer 1.3.6.1.4.1.6296.101.28.6.2.3
the wait-time until setRequest end. In case of short-time command, this value is 0
OBJECT-TYPE    
  Gauge32  

sleMlsQosInterfaceontrolTimeStamp 1.3.6.1.4.1.6296.101.28.6.2.4
the time stamp of the last command. (don.t care)
OBJECT-TYPE    
  TimeTicks  

sleMlsQosInterfaceControlReqResult 1.3.6.1.4.1.6296.101.28.6.2.5
Result of the last command.
OBJECT-TYPE    
  SleControlRequestResultType  

sleMlsQosInterfaceCtrlIndex 1.3.6.1.4.1.6296.101.28.6.2.6
Class map Name
OBJECT-TYPE    
  Integer32  

sleMlsQosInterfaceCtrlMapingType 1.3.6.1.4.1.6296.101.28.6.2.7
Mapping Type: cos (1) Configure interface default CoS values cos-cos (2) Specify cos-cos cos-queue (3) Specify cos-queue map dscp (4) Set the default DSCP vlaue dscp-dscp(5) Specify dscp-dscp dscp-queue (6) DSCP-to-QUEUE exp-exp(7) Specify exp-exp trust (8) Configure port trust state trust-passthrough (9) COnfigure port trust pass-through state cosToClass (10) configure cos to class dscpToClass (11) configure dscp to class
OBJECT-TYPE    
  MlsQosInterfaceMapingType  

sleMlsQosInterfaceCtrlMapingIngVal 1.3.6.1.4.1.6296.101.28.6.2.8
Ingress or incoming mapping values. Based on sleMlsQosInterfaceCtrlMapingType, this value has to be set. Ex. If sleMlsQosInterfaceCtrlMapingType = cosToCos, then sleMlsQosInterfaceCtrlMapingIngVal = Incoming or ingress COS value
OBJECT-TYPE    
  Integer32  

sleMlsQosInterfaceCtrlMapingEgrVal 1.3.6.1.4.1.6296.101.28.6.2.9
Egress or outgoing mapping values. Based on sleMlsQosInterfaceCtrlMapingType, this value has to be set. Ex. If sleMlsQosInterfaceCtrlMapingType = cosToCos, then sleMlsQosInterfaceCtrlMapingIngVal = Egress COS value
OBJECT-TYPE    
  Integer32  

sleMlsQosInterfaceCtrlMapingCosOverride 1.3.6.1.4.1.6296.101.28.6.2.10
Interface COS override value
OBJECT-TYPE    
  Integer32  

sleMlsQosInterfaceCtrlMapingTrustState 1.3.6.1.4.1.6296.101.28.6.2.11
Interface trust state Trust: cos (1) dscp (2) Trust pass-through: pass-through cos (1) pass-through dscp (2)
OBJECT-TYPE    
  MlsQosIntfTrustState  

sleMlsQosInterfaceCtrlTrafficShapeRate 1.3.6.1.4.1.6296.101.28.6.2.12
Interface Traffic shape rate
OBJECT-TYPE    
  Integer32  

sleMlsQosInterfaceCtrlTrafficShapeBurst 1.3.6.1.4.1.6296.101.28.6.2.13
Interface Traffic shape burst
OBJECT-TYPE    
  Integer32  

sleMlsQosInterfaceCtrlInputPolicyMap 1.3.6.1.4.1.6296.101.28.6.2.14
Interface Policy Map mapping
OBJECT-TYPE    
  OCTET STRING  

sleMlsQosInterfaceCtrlOutputPolicyMap 1.3.6.1.4.1.6296.101.28.6.2.15
OBJECT-TYPE    
  OCTET STRING  

sleMlsQosInterfaceCtrlMapingCNGValue 1.3.6.1.4.1.6296.101.28.6.2.16
Specify CNG value <0-1>
OBJECT-TYPE    
  Integer32 0..1  

sleMlsQosInterfaceCtrlMapingEgrClassVal 1.3.6.1.4.1.6296.101.28.6.2.17
OBJECT-TYPE    
  OCTET STRING  

sleMlsQosInterfaceCtrlReplace 1.3.6.1.4.1.6296.101.28.6.2.18
rewite the dscp/cos at egress in uniform mode.
OBJECT-TYPE    
  INTEGER none(0), cos(1), dscp(2)  

sleMlsQosIntfQue 1.3.6.1.4.1.6296.101.28.7
OBJECT IDENTIFIER    

sleMlsQosIntfQueTable 1.3.6.1.4.1.6296.101.28.7.1
OBJECT-TYPE    
  SEQUENCE OF  
    SleMlsQosIntfQueEntry

sleMlsQosIntfQueEntry 1.3.6.1.4.1.6296.101.28.7.1.1
OBJECT-TYPE    
  SleMlsQosIntfQueEntry  

sleMlsQosIntfQueIntfIndex 1.3.6.1.4.1.6296.101.28.7.1.1.1
This Index is based on no of Queues
OBJECT-TYPE    
  Integer32 1..65535  

sleMlsQosIntfQueId 1.3.6.1.4.1.6296.101.28.7.1.1.2
This Index is based on no of Queues
OBJECT-TYPE    
  Integer32 0..7  

sleMlsQosIntfQueShapeQueueRate 1.3.6.1.4.1.6296.101.28.7.1.1.3
Interface Queue Shape rate
OBJECT-TYPE    
  Integer32  

sleMlsQosIntfQueWrrQueueWeight 1.3.6.1.4.1.6296.101.28.7.1.1.4
Interface Queue WRR queue weight
OBJECT-TYPE    
  Integer32  

sleMlsQosIntfQueWrrRandomDetectMinThr 1.3.6.1.4.1.6296.101.28.7.1.1.5
Interface Queue WRR random detect min threshold
OBJECT-TYPE    
  Integer32  

sleMlsQosIntfQueWrrRandomDetectMaxThr 1.3.6.1.4.1.6296.101.28.7.1.1.6
Interface Queue WRR random detect max threshold
OBJECT-TYPE    
  Integer32  

sleMlsQosIntfQueWrrRandomDetectExpWt 1.3.6.1.4.1.6296.101.28.7.1.1.7
Interface Queue WRR random detect exp weight
OBJECT-TYPE    
  Integer32  

sleMlsQosIntfQueTailDropThr 1.3.6.1.4.1.6296.101.28.7.1.1.8
Interface Queue TailDrop threshold
OBJECT-TYPE    
  Integer32  

sleMlsQosIntfQueStrictQueue 1.3.6.1.4.1.6296.101.28.7.1.1.9
Interface Strict Queue Config
OBJECT-TYPE    
  Integer32  

sleMlsQosIntfQueRandomDetectDropStart 1.3.6.1.4.1.6296.101.28.7.1.1.10
WRR Random Detect Drop Start
OBJECT-TYPE    
  Integer32  

sleMlsQosIntfQueRandomDetectDropSlope 1.3.6.1.4.1.6296.101.28.7.1.1.11
WRR Random Detect Drop Slope
OBJECT-TYPE    
  Integer32  

sleMlsQosIntfQueRandomDetectColor 1.3.6.1.4.1.6296.101.28.7.1.1.12
WRR Random Detect Color
OBJECT-TYPE    
  INTEGER yellow(1), red(2)  

sleMlsQosIntfQueReservedBandwidth 1.3.6.1.4.1.6296.101.28.7.1.1.13
Interface Queue Shape rate (minimum)
OBJECT-TYPE    
  Integer32 8..1000000  

sleMlsQosIntfQueControl 1.3.6.1.4.1.6296.101.28.7.2
OBJECT IDENTIFIER    

sleMlsQosIntfQueControlRequest 1.3.6.1.4.1.6296.101.28.7.2.1
the configuration commands, and user can configure functions via setting this entry as proper value.
OBJECT-TYPE    
  INTEGER setQueueProfile(1), unSetQueueProfile(2)  

sleMlsQosIntfQueControlStatus 1.3.6.1.4.1.6296.101.28.7.2.2
status of user command. User have to check this value as .busy. or .idle. before do setRequest.
OBJECT-TYPE    
  SleControlStatusType  

sleMlsQosIntfQueControlTimer 1.3.6.1.4.1.6296.101.28.7.2.3
the wait-time until setRequest end. In case of short-time command, this value is 0
OBJECT-TYPE    
  Gauge32  

sleMlsQosIntfQueontrolTimeStamp 1.3.6.1.4.1.6296.101.28.7.2.4
the time stamp of the last command. (don.t care)
OBJECT-TYPE    
  TimeTicks  

sleMlsQosIntfQueControlReqResult 1.3.6.1.4.1.6296.101.28.7.2.5
Result of the last command.
OBJECT-TYPE    
  SleControlRequestResultType  

sleMlsQosIntfQueCtrlInterfaceIndex 1.3.6.1.4.1.6296.101.28.7.2.6
Queue Id
OBJECT-TYPE    
  Integer32  

sleMlsQosIntfQueCtrlQueueId 1.3.6.1.4.1.6296.101.28.7.2.7
Queue Id
OBJECT-TYPE    
  Integer32  

sleMlsQosIntfQueCtrlProfileType 1.3.6.1.4.1.6296.101.28.7.2.8
OBJECT-TYPE    
  MlsQosIntfQueProfilingType  

sleMlsQosIntfQueCtrlShapeQueueRate 1.3.6.1.4.1.6296.101.28.7.2.9
Interface Queue Rate
OBJECT-TYPE    
  Integer32  

sleMlsQosIntfQueCtrlWrrQueueWeight 1.3.6.1.4.1.6296.101.28.7.2.10
Interface Queue WRR Queue weight
OBJECT-TYPE    
  Integer32  

sleMlsQosIntfQueCtrlWrrRandomDetectMinThr 1.3.6.1.4.1.6296.101.28.7.2.11
Interface Queue WRR random detect Min Threshold
OBJECT-TYPE    
  Integer32  

sleMlsQosIntfQueCtrlWrrRandomDetectMaxThr 1.3.6.1.4.1.6296.101.28.7.2.12
Interface Queue WRR random detect Max Threshold
OBJECT-TYPE    
  Integer32  

sleMlsQosIntfQueCtrlWrrRandomDetectExpWt 1.3.6.1.4.1.6296.101.28.7.2.13
Interface Queue WRR random detect exp weight
OBJECT-TYPE    
  Integer32  

sleMlsQosIntfQueCtrlTailDropThr 1.3.6.1.4.1.6296.101.28.7.2.14
Interface Queue Taildrop Threshold
OBJECT-TYPE    
  Integer32  

sleMlsQosIntfQueCtrlRandomDetectDropStart 1.3.6.1.4.1.6296.101.28.7.2.15
Interface Queue WRR Random Detect Drop Start
OBJECT-TYPE    
  Integer32  

sleMlsQosIntfQueCtrlRandomDetectDropSlope 1.3.6.1.4.1.6296.101.28.7.2.16
Interface Queue WRR Random Detect Drop Slope
OBJECT-TYPE    
  Integer32  

sleMlsQosIntfQueCtrlRandomDetectColor 1.3.6.1.4.1.6296.101.28.7.2.17
Interface Queue WRR Random Detect Color
OBJECT-TYPE    
  INTEGER yellow(1), red(2)  

sleMlsQosIntfQueCtrlReservedBandwidth 1.3.6.1.4.1.6296.101.28.7.2.18
Interface Queue Rate(minimum)
OBJECT-TYPE    
  Integer32 8..1000000  

sleMlsQosQStats 1.3.6.1.4.1.6296.101.28.8
OBJECT IDENTIFIER    

sleMlsQosQStatsTable 1.3.6.1.4.1.6296.101.28.8.1
OBJECT-TYPE    
  SEQUENCE OF  
    SleMlsQosQStatsEntry

sleMlsQosQStatsEntry 1.3.6.1.4.1.6296.101.28.8.1.1
OBJECT-TYPE    
  SleMlsQosQStatsEntry  

sleMlsQosQstatsIfIndex 1.3.6.1.4.1.6296.101.28.8.1.1.1
Index for the table. QStats Name
OBJECT-TYPE    
  Integer32 1..65535  

sleMlsQosQId 1.3.6.1.4.1.6296.101.28.8.1.1.2
This Index is based on Max entries i.e. 64 (dscp)
OBJECT-TYPE    
  Integer32 1..8  

sleMlsQosWredGreenDropPkts 1.3.6.1.4.1.6296.101.28.8.1.1.3
Wred Green drop packet counter
OBJECT-TYPE    
  Counter64  

sleMlsQosWredYellowDropPkts 1.3.6.1.4.1.6296.101.28.8.1.1.4
Wred yellow drop packet counter
OBJECT-TYPE    
  Counter64  

sleMlsQosWredRedDropPkts 1.3.6.1.4.1.6296.101.28.8.1.1.5
Wred red drop packet counter
OBJECT-TYPE    
  Counter64  

sleMlsQosTailDropPkts 1.3.6.1.4.1.6296.101.28.8.1.1.6
Taildrop drop packet counter
OBJECT-TYPE    
  Counter64  

sleMlsQosTailDropBytes 1.3.6.1.4.1.6296.101.28.8.1.1.7
Taildrop drop bytes counter
OBJECT-TYPE    
  Counter64  

sleMlsQosQStatsOutPkts 1.3.6.1.4.1.6296.101.28.8.1.1.8
Total out packets in the Queue
OBJECT-TYPE    
  Counter64  

sleMlsQosQStatsOutBytes 1.3.6.1.4.1.6296.101.28.8.1.1.9
Total out bytes in the Queue
OBJECT-TYPE    
  Counter64  

sleMlsQosQStatsMcastOutPkts 1.3.6.1.4.1.6296.101.28.8.1.1.10
Total mcast out packets in the Queue
OBJECT-TYPE    
  Counter64  

sleMlsQosQStatsMcastOutBytes 1.3.6.1.4.1.6296.101.28.8.1.1.11
Total mcast out bytes in the Queue
OBJECT-TYPE    
  Counter64  

sleMlsQosQStatsDropPkts 1.3.6.1.4.1.6296.101.28.8.1.1.12
Total drop packets in the Queue
OBJECT-TYPE    
  Counter64  

sleMlsQosQStatsDropBytes 1.3.6.1.4.1.6296.101.28.8.1.1.13
Total drop bytes in the Queue
OBJECT-TYPE    
  Counter64  

sleMlsQosQStatsMcastDropPkts 1.3.6.1.4.1.6296.101.28.8.1.1.14
Total mcast drop packets in the Queue
OBJECT-TYPE    
  Counter64  

sleMlsQosQStatsMcastDropBytes 1.3.6.1.4.1.6296.101.28.8.1.1.15
Total mcast drop bytes in the Queue
OBJECT-TYPE    
  Counter64  

sleMlsQosQStatsEnqueuedPkts 1.3.6.1.4.1.6296.101.28.8.1.1.16
Total Enqueued packets in the Queue
OBJECT-TYPE    
  Counter64  

sleMlsQosQStatsEnqueuedBytes 1.3.6.1.4.1.6296.101.28.8.1.1.17
Total Enqueued bytes in the Queue
OBJECT-TYPE    
  Counter64  

sleMlsQosQStatsControl 1.3.6.1.4.1.6296.101.28.8.2
OBJECT IDENTIFIER    

sleMlsQosQStatsControlRequest 1.3.6.1.4.1.6296.101.28.8.2.1
the configuration commands, and user can configure functions via setting this entry as proper value.
OBJECT-TYPE    
  INTEGER clearWredStats(1), clearTailDropStats(2), clearQueueStats(3)  

sleMlsQosQStatsControlStatus 1.3.6.1.4.1.6296.101.28.8.2.2
status of user command. User have to check this value as .busy. or .idle. before do setRequest.
OBJECT-TYPE    
  SleControlStatusType  

sleMlsQosQStatsControlTimer 1.3.6.1.4.1.6296.101.28.8.2.3
the wait-time until setRequest end. In case of short-time command, this value is 0
OBJECT-TYPE    
  Gauge32  

sleMlsQosQStatsontrolTimeStamp 1.3.6.1.4.1.6296.101.28.8.2.4
the time stamp of the last command. (don.t care)
OBJECT-TYPE    
  TimeTicks  

sleMlsQosQStatsControlReqResult 1.3.6.1.4.1.6296.101.28.8.2.5
Result of the last command.
OBJECT-TYPE    
  SleControlRequestResultType  

sleMlsQosQstatsCtrlIfIndex 1.3.6.1.4.1.6296.101.28.8.2.6
Index for the table. Class Map name
OBJECT-TYPE    
  Integer32  

sleMlsQosQstatsCtrlQId 1.3.6.1.4.1.6296.101.28.8.2.7
Class map Name
OBJECT-TYPE    
  Integer32  

sleHqosClassMapQueue 1.3.6.1.4.1.6296.101.28.9
OBJECT IDENTIFIER    

sleHqosClassMapQueueInfoTable 1.3.6.1.4.1.6296.101.28.9.1
This Table is used to show the information for Class Map queueing Table
OBJECT-TYPE    
  SEQUENCE OF  
    SleHqosClassMapQueueInfoEntry

sleHqosClassMapQueueInfoEntry 1.3.6.1.4.1.6296.101.28.9.1.1
This Table is used to show the information for Class Map queueing Table
OBJECT-TYPE    
  SleHqosClassMapQueueInfoEntry  

sleHqosClassMapQueueInfoName 1.3.6.1.4.1.6296.101.28.9.1.1.1
Class Map queue name. An unique object identify an entry of this table.
OBJECT-TYPE    
  OCTET STRING  

sleHqosClassMapQueueInfoMatchGroup 1.3.6.1.4.1.6296.101.28.9.1.1.2
This object is used to show the match group of the class map queueing.
OBJECT-TYPE    
  INTEGER  

sleHqosClassMapQueueControl 1.3.6.1.4.1.6296.101.28.9.2
OBJECT IDENTIFIER    

sleHqosClassMapQueueControlRequest 1.3.6.1.4.1.6296.101.28.9.2.1
the configuration commands, and user can configure functions via setting this entry as proper value.
OBJECT-TYPE    
  INTEGER createSleHqosClassMapQueueControlEntry(1), deleteSleHqosClassMapQueueControlEntry(2), setSleHqosClassMapQueueControlMatchGroup(3), unsetSleHqosClassMapQueueControlMatchGroup(4)  

sleHqosClassMapQueueControlStatus 1.3.6.1.4.1.6296.101.28.9.2.2
status of user command. User have to check this value as .busy. or .idle. before do setRequest.
OBJECT-TYPE    
  SleControlStatusType  

sleHqosClassMapQueueControlTimer 1.3.6.1.4.1.6296.101.28.9.2.3
the wait-time until setRequest end. In case of short-time command, this value is 0
OBJECT-TYPE    
  Gauge32  

sleHqosClassMapQueueControlTimeStamp 1.3.6.1.4.1.6296.101.28.9.2.4
the time stamp of the last command. (don.t care)
OBJECT-TYPE    
  TimeTicks  

sleHqosClassMapQueueControlReqResult 1.3.6.1.4.1.6296.101.28.9.2.5
Result of the last command.
OBJECT-TYPE    
  SleControlRequestResultType  

sleHqosClassMapQueueControlName 1.3.6.1.4.1.6296.101.28.9.2.6
This Object is used to the set the control name for the Class map queue Table
OBJECT-TYPE    
  OCTET STRING  

sleHqosClassMapQueueControlMatchGroup 1.3.6.1.4.1.6296.101.28.9.2.7
This object is used to set the match group of the class map queueing
OBJECT-TYPE    
  INTEGER  

sleHqosPolicyMapQueue 1.3.6.1.4.1.6296.101.28.10
OBJECT IDENTIFIER    

sleHqosPolicyMapQueueInfoTable 1.3.6.1.4.1.6296.101.28.10.1
This table is used to show the Policy mapping queue information of the policy map queueing
OBJECT-TYPE    
  SEQUENCE OF  
    SleHqosPolicyMapQueueInfoEntry

sleHqosPolicyMapQueueInfoEntry 1.3.6.1.4.1.6296.101.28.10.1.1
This table is used to show the Policy mapping queue information of the policy map queueing
OBJECT-TYPE    
  SleHqosPolicyMapQueueInfoEntry  

sleHqosPolicyMapQueueInfoName 1.3.6.1.4.1.6296.101.28.10.1.1.1
This object identify an entry in this table.
OBJECT-TYPE    
  OCTET STRING  

sleHqosPolicyMapQueueInfoShape 1.3.6.1.4.1.6296.101.28.10.1.1.2
This object is used to show the shape for the policy map queue Types: 1)average 1-1000000000(bps|kbps|mbps|gbps) 2)percent 1-100
OBJECT-TYPE    
  SnmpAdminString Size(1..48)  

sleHqosPolicyMapQueueInfoBandwidth 1.3.6.1.4.1.6296.101.28.10.1.1.3
This object is used to show the bandwidth for the policy map queue average 1-1000000000(bps|kbps|mbps|gbps) percent 1-100
OBJECT-TYPE    
  SnmpAdminString Size(1..48)  

sleHqosPolicyMapQueueInfoBandwidthRemainingPercent 1.3.6.1.4.1.6296.101.28.10.1.1.4
This object is used to show the remained bandwidth for the policy map queue
OBJECT-TYPE    
  INTEGER 1..100  

sleHqosPolicyMapQueueInfoQueueLimit 1.3.6.1.4.1.6296.101.28.10.1.1.5
This object is used to show the queue limit for the policy map queue
OBJECT-TYPE    
  SnmpAdminString Size(1..48)  

sleHqosPolicyMapQueueInfoServicePolicyName 1.3.6.1.4.1.6296.101.28.10.1.1.6
This object is used to show the service name for the policy map queue
OBJECT-TYPE    
  SnmpAdminString Size(1..48)  

sleHqosPolicyMapQueueInfoPriority 1.3.6.1.4.1.6296.101.28.10.1.1.7
This object is used to show the priority for the policy map queue Always value is 1
OBJECT-TYPE    
  INTEGER  

sleHqosPolicyMapQueueInfoRDMinThreshold 1.3.6.1.4.1.6296.101.28.10.1.1.8
This object is used to show the random detuct minimum threshold for the policy map queue
OBJECT-TYPE    
  SnmpAdminString Size(1..48)  

sleHqosPolicyMapQueueInfoRDMaxThreshold 1.3.6.1.4.1.6296.101.28.10.1.1.9
This object is used to show the random detuct maximum threshold for the policy map queue
OBJECT-TYPE    
  SnmpAdminString Size(1..48)  

sleHqosPolicyMapQueueControl 1.3.6.1.4.1.6296.101.28.10.2
OBJECT IDENTIFIER    

sleHqosPolicyMapQueueControlRequest 1.3.6.1.4.1.6296.101.28.10.2.1
the configuration commands, and user can configure functions via setting this entry as proper value.
OBJECT-TYPE    
  INTEGER createPolicyMapQueueEntry(1), deletePolicyMapQueueEntry(2), setPolicyMapQueueParameters(3), unsetPolicyMapQueueParameters(4), setPolicyMapQueueServicePolicy(5), unsetPolicyMapQueueServicePolicy(6), setPolicyMapQueueRandomDetect(7), unsetPolicyMapQueueRandomDetect(8)  

sleHqosPolicyMapQueueControlStatus 1.3.6.1.4.1.6296.101.28.10.2.2
status of user command. User have to check this value as .busy. or .idle. before do setRequest.
OBJECT-TYPE    
  SleControlStatusType  

sleHqosPolicyMapQueueControlTimer 1.3.6.1.4.1.6296.101.28.10.2.3
the wait-time until setRequest end. In case of short-time command, this value is 0
OBJECT-TYPE    
  Gauge32  

sleHqosPolicyMapQueueControlTimeStamp 1.3.6.1.4.1.6296.101.28.10.2.4
the time stamp of the last command. (don.t care)
OBJECT-TYPE    
  TimeTicks  

sleHqosPolicyMapQueueControlReqResult 1.3.6.1.4.1.6296.101.28.10.2.5
Result of the last command.
OBJECT-TYPE    
  SleControlRequestResultType  

sleHqosPolicyMapQueueControlName 1.3.6.1.4.1.6296.101.28.10.2.6
This object is used to set the name for the policy map queue
OBJECT-TYPE    
  OCTET STRING  

sleHqosPolicyMapQueueControlClassMapQueueName 1.3.6.1.4.1.6296.101.28.10.2.7
This object is used to set the name for the policy map queue
OBJECT-TYPE    
  OCTET STRING  

sleHqosPolicyMapQueueControlParams 1.3.6.1.4.1.6296.101.28.10.2.8
This object is used to set 1)shape: the shape for the policy map queue is to configure shaping on an egress queue to impose a maximum rate on it 2)queue-limit: the Queue Limit is to configure tail drop by setting queue limits on both ingress and egress queues 3)bandwidth: To allocate a minimum percentage of the interface bandwidth to a queue 4)bandwidth-Remain: To configures the bandwidth remaining on the interface in a queue 5)Priority: To configure a single output queuing class as the priority queue average 1-1000000000(bps|kbps|mbps|gbps) limit 1-131072 (packets | bytes | kbytes) percent 1-100
OBJECT-TYPE    
  INTEGER shape(1), queueLimit(2), bandwidth(3), bandwidthRemain(4), priority(5)  

sleHqosPolicyMapQueueControlParamsValue 1.3.6.1.4.1.6296.101.28.10.2.9
This object is used to set 1)shape: the shape for the policy map queue is to configure shaping on an egress queue to impose a maximum rate on it 2)queue-limit: the Queue Limit is to configure tail drop by setting queue limits on both ingress and egress queues 3)bandwidth: To allocate a minimum percentage of the interface bandwidth to a queue 4)bandwidth-Remain: To configures the bandwidth remaining on the interface in a queue 5)Priority: To configure a single output queuing class as the priority queue average 1-1000000000(bps|kbps|mbps|gbps) limit 1-131072 (packets | bytes | kbytes) percent 1-100
OBJECT-TYPE    
  INTEGER  

sleHqosPolicyMapQueueControlUnits 1.3.6.1.4.1.6296.101.28.10.2.10
This object is used to set the units for the specified objects
OBJECT-TYPE    
  INTEGER bps(1), kbps(2), mbps(3), gbps(4), packets(5), bytes(6), kbytes(7), average(8), percent(9)  

sleHqosPolicyMapQueueControlRDMiniThreshold 1.3.6.1.4.1.6296.101.28.10.2.11
his object is used to set the Minimum random threashold
OBJECT-TYPE    
  INTEGER 1..131072  

sleHqosPolicyMapQueueControlRDMaxThreshold 1.3.6.1.4.1.6296.101.28.10.2.12
This object is used to set the Maximum random threashold
OBJECT-TYPE    
  INTEGER 1..131072  

sleHqosPolicyMapQueueControlRDMinimumUnits 1.3.6.1.4.1.6296.101.28.10.2.13
This object is used to set the units for Random Minimum
OBJECT-TYPE    
  INTEGER bytes(1), kbytes(2), packets(3), percent(4)  

sleHqosPolicyMapQueueControlRDMaximumUnits 1.3.6.1.4.1.6296.101.28.10.2.14
This object is used to set the units for Random Maximum
OBJECT-TYPE    
  INTEGER bytes(1), kbytes(2), packets(3), percent(4)  

sleHqosPolicyMapQueueControlServicePolicyName 1.3.6.1.4.1.6296.101.28.10.2.15
This object is used to set the service name, to attach a child policy onto a parent policy
OBJECT-TYPE    
  SnmpAdminString Size(1..48)  

sleMlsQosAclGlobal 1.3.6.1.4.1.6296.101.28.11
OBJECT IDENTIFIER    

sleMlsQosAclGlobalInfo 1.3.6.1.4.1.6296.101.28.11.1
OBJECT IDENTIFIER    

sleMlsQosAclGlobalInfoMaxAccessList 1.3.6.1.4.1.6296.101.28.11.1.1
Max accessList suported
OBJECT-TYPE    
  Unsigned32  

sleMlsQosAclGlobalControl 1.3.6.1.4.1.6296.101.28.11.2
OBJECT IDENTIFIER    

sleMlsQosAclGlobalControlRequest 1.3.6.1.4.1.6296.101.28.11.2.1
The configuration commands, and user can configure functions via setting this entry as proper value.
OBJECT-TYPE    
  INTEGER setMaxAccessList(1), unsetMaxAccessList(2)  

sleMlsQosAclGlobalControlStatus 1.3.6.1.4.1.6296.101.28.11.2.2
status of user command. User have to check this value as .busy. or .idle. before do setRequest.
OBJECT-TYPE    
  SleControlStatusType  

sleMlsQosAclGlobalControlTimer 1.3.6.1.4.1.6296.101.28.11.2.3
the wait-time until setRequest end. In case of short-time command, this value is 0
OBJECT-TYPE    
  Gauge32  

sleMlsQosAclGlobalControlTimeStamp 1.3.6.1.4.1.6296.101.28.11.2.4
the time stamp of the last command. (don.t care)
OBJECT-TYPE    
  TimeTicks  

sleMlsQosAclGlobalControlReqResult 1.3.6.1.4.1.6296.101.28.11.2.5
Result of the last command.
OBJECT-TYPE    
  SleControlRequestResultType  

sleMlsQosAclGlobalControlMaxAccessList 1.3.6.1.4.1.6296.101.28.11.2.6
Max accessList suported
OBJECT-TYPE    
  Unsigned32  

sleMlsQosGroup 1.3.6.1.4.1.6296.101.28.12
Description.
OBJECT-GROUP