SHIVA-AT-MIB

File: SHIVA-AT-MIB.mib (8465 bytes)

Imported modules

RFC-1212 SHIVA-MIB

Imported symbols

OBJECT-TYPE tATalk

Defined Values

tRTMPEntryTimeouts 1.3.6.1.4.1.166.4.2.1
The number of entries which were removed from routing table because the aging algorithm indicated that they were invalid.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER  

tRTMPEntryDeletes 1.3.6.1.4.1.166.4.2.2
The number of entries which were removed from the routing table for any reason other than aging, for instance, due to a command from a Network Management station.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER  

tRTMPEntryEqualReplaces 1.3.6.1.4.1.166.4.2.3
The number of entries whose route was replaced by another route with the same hop count.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER  

tRTMPEntryBetterReplaces 1.3.6.1.4.1.166.4.2.4
The number of entries whose route was replaced by another route with a lower hop count.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER  

tRTMPEntryAdds 1.3.6.1.4.1.166.4.2.5
The number of new entries which have been added to the table.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER  

tRTMPZeroCounters 1.3.6.1.4.1.166.4.2.6
Writing this variable causes all the RTMP variables in this group to be set to zero.
Status: mandatory Access: read-write
OBJECT-TYPE    
  INTEGER zero(1)  

tZIPDeletes 1.3.6.1.4.1.166.4.2.7
The number of Zones which have been deleted from the Zone Table.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER  

tZIPAdds 1.3.6.1.4.1.166.4.2.8
The number of Zones which have been added to the Zone Table.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER  

tZIPZeroCounters 1.3.6.1.4.1.166.4.2.9
Writing this variable causes all the ZIP variables in this group to be set to zero.
Status: mandatory Access: read-write
OBJECT-TYPE    
  INTEGER zero(1)  

tAARPClearCache 1.3.6.1.4.1.166.4.2.10
Writing this variable clears the AARP Cache.
Status: mandatory Access: read-write
OBJECT-TYPE    
  INTEGER clear(1)  

tKIPRoutesValid 1.3.6.1.4.1.166.4.2.11
This variable can be used to force KIP to reacquire its configuration information.
Status: mandatory Access: read-write
OBJECT-TYPE    
  INTEGER valid(1), invalid(2)  

tNBPDeviceObject 1.3.6.1.4.1.166.4.2.12
The NBP name used to advertise this device's primary NVE on the LAN interface.
Status: mandatory Access: read-only
OBJECT-TYPE    
  OCTET STRING  

tNBPDeviceType 1.3.6.1.4.1.166.4.2.13
The NBP type used to advertise this device's primary NVE on the LAN interface.
Status: mandatory Access: read-only
OBJECT-TYPE    
  OCTET STRING  

tNBPDeviceZone 1.3.6.1.4.1.166.4.2.14
The zone in which this device registers its primary NVE on the LAN interface.
Status: mandatory Access: read-only
OBJECT-TYPE    
  OCTET STRING  

tNBPDeviceSocket 1.3.6.1.4.1.166.4.2.15
The DDP socket number used by the device in NBP Responses for its primary NVE registered on the LAN interface.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER  

tATDialinNetwork 1.3.6.1.4.1.166.4.2.16
The AppleTalk network number in which AppleTalk dialin users appear. When tATDialInPacketDeliveryMode is routing(1) this value corresponds to the configured dialin network number. When tATDialInPacketDeliveryMode is endNodeForwarding(2) this value corresponds to the network number of the LAN interface. Note that when endNodeForwarding(2) it is possible that not all dialin clients have addresses on this network because there may not have been enough available node ids to obtain addresses for all of the clients. In this case another network in the extended range of the LAN interface may be used for the remaining clients' addresses. Ideally this should be a table of clients with their dialin addresses.
Status: mandatory Access: read-only
OBJECT-TYPE    
  OCTET STRING Size(2)  

tATDialinZone 1.3.6.1.4.1.166.4.2.17
The zone with which tATDialinNetwork is associated.
Status: mandatory Access: read-only
OBJECT-TYPE    
  OCTET STRING Size(2)  

tATRoutingMode 1.3.6.1.4.1.166.4.2.18
The routing behavior of this device for AppleTalk. If the device is configured as conformingRouter(1) or seedRouter(2) then it will behave as an AppleTalk router on the LAN interface, and will route packets to all interfaces. If it is a conformingRouter(1) then it will learn its configuration for the LAN interface from other routers on that interface's directly-connected network. If it is a seedRouter(2) then it will use the configured LAN interface parameters. If the device is configured as endNode(3) it will behave as an AppleTalk endnode on the LAN interface. other(4) is provided in the event a value is returned which does not match any of the other enumerated values. It is not expected that this will happen.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER conformingRouter(1), seedRouter(2), endNode(3), other(4)  

tATDialinPacketDeliveryMode 1.3.6.1.4.1.166.4.2.19
The method used to deliver packets to and from Appletalk dialin clients. If the device is configured as routing(1) it will use routing tables to deliver packets to and from dialin clients, which will be homed on an internal virtual interface (port). Technically, the value routing(1) is only valid if the device is acting as a router (the value of tATRoutingMode is conformingRouter(1) or seedRouter(2)). If the device is configured to use endNodeForwarding(2) then it will obtain addresses for dialin users in the LAN network range, and will defend those addresses. Packets to and from dialin clients will be forwarded. Technically the device may be configured as endNodeForwarding(2) when tATRoutingMode is any of: conformingRouter(1), seedRouter(2), or endNode(3). other(3) is provided in the event a value is returned which does not match any of the other enumerated values. It is not expected that this will happen.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER routing(1), endNodeForwarding(2), other(3)  

tRTMPEntryTotal 1.3.6.1.4.1.166.4.2.20
The number of network (range) entries in the device's RTMP Table. This value is not cleared by the tRTMPZeroCounters switch.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER  

tZoneTotal 1.3.6.1.4.1.166.4.2.21
The number of AppleTalk zones for which the device has learned one or more associated nets or net ranges. This value is not cleared by the tZIPZeroCounters switch.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER