SHE-ADSL-MIB

File: SHE-ADSL-MIB.mib (468060 bytes)

Imported modules

ADSL-TC-MIB AN-MIB IF-MIB
PerfHist-TC-MIB SHE-ALARMING-MIB SHE-TC-MIB
SNMP-FRAMEWORK-MIB SNMPv2-CONF SNMPv2-SMI
SNMPv2-TC

Imported symbols

AdslLineCodingType AdslPerfTimeElapsed AdslPerfCurrDayCount
AdslPerfPrevDayCount she DisplayString
ifNumber ifIndex InterfaceIndex
PerfCurrentCount PerfIntervalCount sheAlarmTimeAndDate
sheAlarmReportingSource sheAlarmReportingSourceType sheAlarmSeverity
SheAlarmSevProfileIndex SheControlStatusType SnmpAdminString
OBJECT-GROUP MODULE-COMPLIANCE NOTIFICATION-GROUP
transmission Integer32 Unsigned32
Gauge32 Counter32 OBJECT-TYPE
MODULE-IDENTITY NOTIFICATION-TYPE VariablePointer
TruthValue TEXTUAL-CONVENTION

Defined Types

SheDslSystemType  
INTEGER adsl(1), sdsl(2), shdsl(3)    

SheDslSystemLineCodingType  
INTEGER other(1), dmt(2), cap(3), qam(4)    

SheDslSystemTxCfgType  
BITS unused(0), etsi(1), q9921PotsNonOverlapped(2), q9921PotsOverlapped(3), q9921IsdnNonOverlapped(4), q9921IsdnOverlapped(5), q9921TcmIsdnNonOverlapped(6), q9921TcmIsdnOverlapped(7), q9922PotsNonOverlapped(8), q9922PotsOverlapped(9), q9922TcmIsdnNonOverlapped(10), q9922TcmIsdnOverlapped(11), q9922TcmIsdnSymmetric(12), adslPlusPotsNonOverlapped(13)    

SheAdslControlRequestType  
INTEGER noRequest(1), setDslSystemLineTxCfg(101), createAdslLineConfProfile(150), modifyAdslLineConfProfile(151), deleteAdslLineConfProfile(152), createAdslLineConfProfileAnnexA(155), createAdslLineConfProfileAnnexB(156), createAdslLineConfProfileAdsl2PlusAnnexB(157), modifyAdslLineConfExtnProfile(161), modifyAdslLineEntry(201), modifyAdslLineAlarmConfProfileEntry(202), modifyAdslLineDeltConfEntry(203), forceAdslLinePwrMgmtState(204), clearAdslLinePerfCounter(205), modifyAdslLineRfiBandMask(206), setAdslLineDpboProfileEntry(210), createAdslLineAlarmConfProfile(250), modifyAdslLineAlarmConfProfile(251), deleteAdslLineAlarmConfProfile(252), createAdslLineDpboProfile(270), modifyAdslLineDpboProfile(271), deleteAdslLineDpboProfile(272), createAdslVccTp(301), deleteAdslVccTp(302), modifyAdslVccTp(303), modifyAdslVccTpLoopTest(304), modifyAdslVccTpEgressShaping(305), modifyAdslVccTpIngressPolicing(306), modifyAdslVccTpEncap(307), modifyAdslVccTpAdminState(315), modifyAdslVccTpOrl(316), modifyAdslVccTpUsedDslChannel(321), deleteAdslVccTpPerformanceCounters(325), createAdslRfiBand(351), deleteAdslRfiBand(352), createAdslLineConfProfileAdsl2AnnexI(400), createAdslLineConfProfileAdsl2AnnexJ(401), createAdslLineConfProfileAdsl2PlusAnnexI(402), createAdslLineConfProfileAdsl2PlusAnnexJ(403), createAdslLineConfProfileAdsl2AnnexM(404), createAdslLineConfProfileAdsl2PlusAnnexM(405), createAdslLineConfProfileAdsl2PlusDynamic(410)    

SheAdslControlRequestResultType  
INTEGER noRequest(1), comExecStarted(30), paramFaulty(31), requestBusy(32), setDataFailed(34), aswTimeout(35), commandFailed(36), commandSucceeded(37), profileNameStringUnknown(2001), profileNameToLong(2002), profileNameAlreadyExist(2003), maxNumberOfProfilesReached(2004), profileNotExist(2005), profileAssignFailOnActivePort(2006), profileTypDefaultCouldNotModified(2010), profileCreateFailOnInvalidArguments(2011), profileModifyFailOnInvalidArguments(2012), profileModifyFailOnInvalidMarginSettings(2013), profileModifyFailOnInvalidDataRateSettings(2014), profileLineTypModifyFailOnAssignedProfiles(2015), internalFailureWriteToDataBase(2020), internalFailureReadFromDataBase(2021), profileUsedByActivePorts(2022), internalFailureDuringIuCommunication(2030), portNumberNotExist(2040), portNumberHasWrongDSLType(2041), profileMinBandwithNotSatisfiedForCAC(2050)    

SheAdslLineConfRateModeType  
INTEGER fixed(1), adaptAtStartup(2), adaptAtRuntime(3)    

SheAdslLineTrellisModeType  
INTEGER unknown(0), trellisOn(1), trellisOff(2)    

SheAdslLineConfRsIntCorrectionType  
INTEGER value125us(3), value250us(4), value500us(5), value1ms(6), value2ms(7), value4ms(8), disable(15)    

SheAdslConfLineType  
INTEGER noChannel(1), fastOnly(2), interleavedOnly(3), fastOrInterleaved(4), fastAndInterleaved(5)    

SheAdslLineConfExtnProfileRxBinAdjustType  
INTEGER 0    

SheAdslLineConfTriggerModeType  
INTEGER disable(0), locCrc(1), rmtCrc(2), snrInc(4), snrDec(8)    

SheAdslLineConfExtnProfileAdi2xType  
INTEGER 1    

SheAdslLineConfStandardType  
INTEGER t1413(0), gLite(1), gDmt(2), multiMode(4), adsl2(26), adsl2Plus(27), readsl2(28), adsl2Auto(29), adsl2PlusAuto(30), adsl2adsl2PlusOnly(31)    

SheAdslLineConfInitiateType  
INTEGER waitPn(0), ctone(1), initiatePn(128)    

SheAdslLineConfAttenuationType  
INTEGER attenuation0(0), attenuation1(1), attenuation2(2), attenuation3(3), attenuation4(4), attenuation5(5), attenuation6(6), attenuation7(7), attenuation8(8), attenuation9(9), attenuation10(10), attenuation11(11), attenuation12(12), attenuation13(13), attenuation14(14), attenuation15(15), attenuation16(16), attenuation17(17), attenuation18(18), attenuation19(19), attenuation20(20), attenuation21(21), attenuation22(22), attenuation23(23), attenuation24(24), attenuation25(25), attenuation26(26), attenuation27(27), attenuation28(28), attenuation29(29), attenuation30(30), attenuation31(31), attenuation32(32), attenuation33(33), attenuation34(34), attenuation35(35), attenuation36(36), attenuation37(37), attenuation38(38), attenuation39(39), attenuation40(40)    

SheAdslLineConfGainType  
INTEGER gain0(0), gain1(4096), gain2(8192), gain3(12288), gain4(16384), gain5(20480), gain6(24576), gain7(28672), auto(65280)    

SheAdslLineConfRsFastOvrhdType  
INTEGER ovrHd50(1), ovrHd25(2), ovrHd12(3), ovrHd6(4), ovrHd3(5), ovrHd1(7), disable(15)    

SheAdslLineConfEnableType  
INTEGER disable(0), enable(1)    

SheAdslLineConfExpandedExchangeType  
INTEGER short(0), expanded(32768)    

SheAdslLineConfEnableSpecial3Type  
INTEGER enable(0), disable(32768)    

SheAdslLineConfEnableSpecial2Type  
INTEGER disable(0), enable(32768)    

SheAdslLineConfNtrType  
INTEGER localOcs(0), refck8K(1)    

SheAdslLineConfAnnexType  
INTEGER annexA(0), annexB(1), highSpeed(2), annexAdsl2(5), annexI(10), annexJ(11), annexM(12), dynamic(50)    

SheAdslLineConfExtnProfileAlctlUsVerType  
INTEGER 2    

SheAdslLineConfIntDephtType  
INTEGER value64(0), value128(4096), value256(8192)    

SheAdslLineConfAdvertisedCapabilitiesType  
INTEGER disable(0), annexA(1), annexb(2), annexI(9), annexJ(10), annexM(13), adslPlus(16), adslPlusAnnexA(17)    

SheAdslLineConfPsdMaskType  
INTEGER adsl(0), hsadslM1(3), hsadslM2(4), adsl2NonOvlpFlat(259), adsl2NonOvlpM1(275), adsl2NonOvlpM2(291), msk2Rf1(32768), flatMskRfi(32771), cabMsk2Rfi(32772)    

SheAdslLineConfLineDmtConfModeType  
INTEGER ecMode(1), fdmMode(2)    

SheAdslLineConfRsMemoryType  
INTEGER present(0), notpresent(32768)    

SheAdslConfMinInpType  
INTEGER null(0), halfSymbol(50), oneSymbol(100), twoSymbol(200), threeSymbol(203), fourSymbol(204), fiveSymbol(205), sixSymbol(206), sevenSymbol(207), eigthSymbol(208), nineSymbol(209), tenSymbol(210), elevenSymbol(211), twelveSymbol(212), thirteenSymbol(213), fourteenSymbol(214), fifteenSymbol(215), sixteenSymbol(216), auto(400)    

SheAdslLineConfUpstreamPSDMaskSelectionType  
INTEGER noSelection(0), adlu32eu32(1), adlu36eu36(2), adlu40eu40(3), adlu44eu44(4), adlu48eu48(5), adlu52eu52(6), adlu56eu56(7), adlu60eu60(8), adlu64eu64(9), extended(10), standard(11), jj100(12)    

SheAdslControlPSDMASKdsRequestResultType  
INTEGER noRequest(1), commandSucceeded(2), psdDataWrongType(30), psdDataWrongLength(31), missingStartTone(32), missingEndTone(33), outOfToneRange(34), duplicateTone(35), oufOfInputPSD(36), oufOfPsdLevel(37), psdModeNotSupport(38), outOfNomPSDRange(39), outOfAtpRange(40)    

SheAdslLineActionType  
INTEGER startup(0), spectrumReverb(5), analogLb(6), digitalLb(7), atmLb(10), spectrumMedley(26), spectrumPilot(27), spectrumCMtpr(30), spectrumRMtpr(32), hybridLossTest(33), rcvLinearityTest(34), rcvFilterTest(35), rcvPowerPerBinTest(36), idleNoisePerBinTest(37), totalIdleNoiseTest(38)    

SheAdslLineClockType  
INTEGER oscillator(0), crystal(4)    

SheAdslAtuxCapabilityType  
BITS q9921GspanPlusPotsNonOverlapped(0), q9921GspanPlusPotsOverlapped(1), q9923Adsl2PotsOverlapped(2), q9923Adsl2PotsNonOverlapped(3), q9925Adsl2PlusPotsOverlapped(4), q9925Adsl2PlusPotsNonOverlapped(5), q9923ReAdsl2PotsNonOverlapped(8), q9923ReAdsl2PotsOverlapped(9), q9925Adsl2PlusIsdnAllDigitalOverlapped(10), q9923Adsl2IsdnAllDigitalNonOverlapped(11), q9923Adsl2IsdnAllDigitalOverlapped(12), adslPlusPotsOverlapped(13), q9925Adsl2PlusIsdnNonOverlapped(14), q9925Adsl2PlusIsdnOverlapped(15), q9923Adsl2IsdnNonOverlapped(16), q9923Adsl2IsdnOverlapped(17), adslPlusPotsNonOverlapped(18), q9921TcmIsdnSymmetric(19), q9922TcmIsdnOverlapped(20), q9922TcmIsdnNonOverlapped(21), q9922PotsOverlapped(22), q9922PotsNonOverlapped(23), q9921TcmIsdnOverlapped(24), q9921TcmIsdnNonOverlapped(25), q9921IsdnOverlapped(26), q9921IsdnNonOverlapped(27), q9921PotsOverlapped(28), q9921PotsNonOverlapped(29), etsi(30), t1413(31), q9925Adsl2PlusPotsExtendedUpstreamNonOverlapped(32), q9925Adsl2PlusPotsExtendedUpstreamOverlapped(33), q9925Adsl2PlusPotsAllDigitalOverlapped(38), q9925Adsl2PlusPotsAllDigitalNonOverlapped(39), q9925Adsl2PlusIsdnAllDigitalNonOverlapped(51), q9923Adsl2PotsAllDigitalNonOverlapped(52), q9923Adsl2PotsAllDigitalOverlapped(53), q9923Adsl2PotsExtendedUpstreamNonOverlapped(56), q9923Adsl2PotsExtendedUpstreamOverlapped(57)    

SheAdslLineCurrentStatusType  
INTEGER noError(1), lossOfFraming(2), lossOfSignal(4), lossOfPower(8), lossOfSignalQuality(16), lossOfLink(32), dataInitFailure(64), configInitFailure(128), protocolInitFailure(256), noPeerAtuPresent(512)    

SheAdslLineOpStateType  
INTEGER idle(0), data(1), bootUpLoad(8), handshake(16), training(24), framerSync(26), fastRetrainInProg(27), discovery(46), llTest(128), dlTest(131), txTest(132), atmLpTest(133), deltTraining(139), delt(140)    

SheAdslAtucPhysBertSyncType  
INTEGER bertOutOfSync(0), bertInSync(128)    

SheAdslPhysAtucDeltLastTxStateType  
INTEGER dmtatucg9941(0), dmtatucquiet1(1), dmtatuccomb1(2), dmtatucquiet2(3), dmtatuccomb2(4), dmtatucicomb1(5), dmtatuclineprob(6), dmtatucquiet3(7), dmtatuccomb3(8), dmtatucicomb2(9), dmtatucmsgfmt(10), dmtatucmsgpcb(11), dmtatucquiet4(12), dmtatucreverb1(13), dmtatuctref1(14), dmtatucreverb2(15), dmtatucect(16), dmtatucreverb3(17), dmtatuctref2(18), dmtatucreverb4(19), dmtatucsegue1(20), dmtatucmsg1(21), dmtatucreverb5(22), dmtatucsegue2(23), dmtatucmedley(24), dmtatucexchmarker(25), dmtatucmsg2(26), dmtatucreverb6(27), dmtatucsegue3(28), dmtatucparams(29), dmtatucreverb7(30), dmtatucsegue4(31), dmtatucshowtime(32)    

SheAdslPhysAturDeltLastTxStateType  
INTEGER dmtaturg9941(0), dmtaturquiet1(1), dmtaturcomb1(2), dmtaturquiet2(3), dmtaturcomb2(4), dmtaturicomb1(5), dmtaturlineprob(6), dmtaturquiet3(7), dmtaturcomb3(8), dmtaturicomb2(9), dmtaturmsgfmt(10), dmtaturmsgpcb(11), dmtaturreverb1(12), dmtaturquiet4(13), dmtaturreverb2(14), dmtaturquiet5(15), dmtaturreverb3(16), dmtaturect(17), dmtaturreverb4(18), dmtatursegue1(19), dmtaturreverb5(20), dmtatursegue2(21), dmtaturmsg1(22), dmtaturmedley(23), dmtaturexchmarker(24), dmtaturmsg2(25), dmtaturreverb6(26), dmtatursegue3(27), dmtaturparams(28), dmtaturreverb7(29), dmtatursegue4(30), dmtaturshowtime(31)    

SheAdslAtucPhysParametricTestResultType  
INTEGER ok(0), fail(1), dspIfFail(2)    

SheAdslLineActStateType  
INTEGER noError(0), errPsdMaskds(1), errMaxNomPsdds(2), errMaxNomAtpds(3), errPsdMaskMaxBreakPoints(4), errPsdMode(5), errResultPsdMask(6), errPsdMaskConfig(7), warnG997PsdMaskConfig(8), warnG997PsdMaskConfigIndexOutOfRange(9), warnG997PsdMaskConfigLevelOutOfRange(10), warnG997PsdMaskConfigNoVaildBreakPoints(11), warnDevPsdMaskMaxBreakPoints(12), warnDevPsdMaskOufOfBandBreakPoints(13), warnDevPsdInternal(14), warnDevPsdMode(15)    

SheAdslLineAtmStatus  
INTEGER noAtmDefect(0), noCellDeleniation(1), lossOfCellDeleniation(2)    

SheAdslOamLevelType  
INTEGER undefined(0), f1(1), f2(2), f3(3), f4(4), f5(5)    

SheAdslOamLoopTestType  
INTEGER none(0), segment(1), endToEnd(2)    

SheAdslVccTpLoopTestResultType  
INTEGER segSuccess(0), segFailure(1), endToEndSuccess(2), endToEndFailure(3), aborted(4), progress(5), notAvailable(65535)    

SheAdslAtmQosType  
INTEGER unshaped(0), shapingCbr(1), shapingRtVbr(2), shapingNrtVbr(3), shapingUbr(4)    

SheAdslLineConfEnableSpecial1Type  
INTEGER enable(1), disable(32768)    

SheAdslLineTransAtucCapType  
BITS ansit1413(0), etsi(1), q9921PotsNonOverlapped(2), q9921PotsOverlapped(3), q9921IsdnNonOverlapped(4), q9921IsdnOverlapped(5), q9921TcmIsdnNonOverlapped(6), q9921TcmIsdnOverlapped(7), q9922PotsNonOverlapped(8), q9922PotsOverlapped(9), q9922TcmIsdnNonOverlapped(10), q9922TcmIsdnOverlapped(11), q9922TcmIsdnSymmetric(12), adslPlusPotsNonOverlapped(13)    

SheAdslEnableType  
INTEGER enable(1), disable(2)    

SheAdslPwrMgmtPMSFType  
INTEGER pmsfL3ToL0StateForce(0), pmsfL0ToL2StateForce(1), pmsfL3StateForce(2), pmsfL2ToL0StateForce(3)    

SheAdslPwrMgmtStateType  
INTEGER idle(0), data(1), l2(141)    

SheAdslPwrMgmtModeType  
INTEGER disable(0), l2Enabled(1), l2andl3Enabled(2)    

SheAdslAtmEncapType  
INTEGER llc(1), vcMux(2)    

SheAdslLineDeltConfLDSFType  
DELT-related parameter. Not available for ADSL but ADSL2 and ADSL2plus.
TEXTUAL-CONVENTION    
  INTEGER inhibit(0), force(1)  

SheAdslChannelType  
The used adsl bearer channel type.
TEXTUAL-CONVENTION    
  INTEGER interleaved(1), fast(2)  

SheAdslLineConfProfileEntry  
SEQUENCE    
  sheAdslLineConfProfileIndex Integer32
  sheAdslLineConfProfileName SnmpAdminString
  sheAdslLineConfProfileAtucConfRateMode SheAdslLineConfRateModeType
  sheAdslLineConfProfileAtucConfRateChanRatio INTEGER
  sheAdslLineConfProfileAtucConfTargetSnrMgn INTEGER
  sheAdslLineConfProfileAtucConfMaxSnrMgn INTEGER
  sheAdslLineConfProfileAtucConfMinSnrMgn INTEGER
  sheAdslLineConfProfileAtucConfDownshiftSnrMgn INTEGER
  sheAdslLineConfProfileAtucConfUpshiftSnrMgn INTEGER
  sheAdslLineConfProfileAtucConfMinUpshiftTime INTEGER
  sheAdslLineConfProfileAtucConfMinDownshiftTime INTEGER
  sheAdslLineConfProfileAtucChanConfFastMinTxRate Unsigned32
  sheAdslLineConfProfileAtucChanConfInterleaveMinTxRate Unsigned32
  sheAdslLineConfProfileAtucChanConfFastMaxTxRate Unsigned32
  sheAdslLineConfProfileAtucChanConfInterleaveMaxTxRate Unsigned32
  sheAdslLineConfProfileAtucChanConfMaxInterleaveDelay INTEGER
  sheAdslLineConfProfileAturConfRateMode SheAdslLineConfRateModeType
  sheAdslLineConfProfileAturConfRateChanRatio INTEGER
  sheAdslLineConfProfileAturConfTargetSnrMgn INTEGER
  sheAdslLineConfProfileAturConfMaxSnrMgn INTEGER
  sheAdslLineConfProfileAturConfMinSnrMgn INTEGER
  sheAdslLineConfProfileAturConfDownshiftSnrMgn INTEGER
  sheAdslLineConfProfileAturConfUpshiftSnrMgn INTEGER
  sheAdslLineConfProfileAturConfMinUpshiftTime INTEGER
  sheAdslLineConfProfileAturConfMinDownshiftTime INTEGER
  sheAdslLineConfProfileAturChanConfFastMinTxRate Unsigned32
  sheAdslLineConfProfileAturChanConfInterleaveMinTxRate Unsigned32
  sheAdslLineConfProfileAturChanConfFastMaxTxRate Unsigned32
  sheAdslLineConfProfileAturChanConfInterleaveMaxTxRate Unsigned32
  sheAdslLineConfProfileAturChanConfMaxInterleaveDelay INTEGER
  sheAdslLineConfProfileTrellis SheAdslLineTrellisModeType
  sheAdslLineConfProfileAtucConfPwrMgmtL0Time INTEGER
  sheAdslLineConfProfileAtucConfPwrMgmtL2Time INTEGER
  sheAdslLineConfProfileAtucConfPwrMgmtL2ATPR INTEGER
  sheAdslLineConfProfileAtucConfPwrMgmtL2Rate INTEGER
  sheAdslLineConfProfileAtucConfPwrMgmtMode SheAdslPwrMgmtModeType

SheAdslLineConfExtnProfileEntry  
SEQUENCE    
  sheAdslLineConfExtnProfileParametricTestInputFile DisplayString
  sheAdslLineConfExtnProfileRsIntCorrectionUp SheAdslLineConfRsIntCorrectionType
  sheAdslLineConfExtnProfileLineType SheAdslConfLineType
  sheAdslLineConfExtnProfileTxEndBin INTEGER
  sheAdslLineConfExtnProfileTxStartBin INTEGER
  sheAdslLineConfExtnProfileMaxBitsPerBin INTEGER
  sheAdslLineConfExtnProfileRxStartBin INTEGER
  sheAdslLineConfExtnProfileRxEndBin INTEGER
  sheAdslLineConfExtnProfileRxBinAdjust SheAdslLineConfExtnProfileRxBinAdjustType
  sheAdslLineConfExtnProfileTriggerMode SheAdslLineConfTriggerModeType
  sheAdslLineConfExtnProfileAdi2x SheAdslLineConfExtnProfileAdi2xType
  sheAdslLineConfExtnProfileStandard SheAdslLineConfStandardType
  sheAdslLineConfExtnProfileInitiate SheAdslLineConfInitiateType
  sheAdslLineConfExtnProfileTxPowerAttenuation SheAdslLineConfAttenuationType
  sheAdslLineConfExtnProfileCodingGain SheAdslLineConfGainType
  sheAdslLineConfExtnProfileRsFastOvrhdDown SheAdslLineConfRsFastOvrhdType
  sheAdslLineConfExtnProfileIntCorrectionDown SheAdslLineConfRsIntCorrectionType
  sheAdslLineConfExtnProfileRsFastOvrhdUp SheAdslLineConfRsFastOvrhdType
  sheAdslLineConfExtnProfileDrStby SheAdslLineConfEnableType
  sheAdslLineConfExtnProfileExpandedExchange SheAdslLineConfExpandedExchangeType
  sheAdslLineConfExtnProfileEscapeFastRetrainEnable SheAdslLineConfEnableType
  sheAdslLineConfExtnProfileFastRetrainEnable SheAdslLineConfEnableSpecial3Type
  sheAdslLineConfExtnProfileBitSwap SheAdslLineConfEnableSpecial2Type
  sheAdslLineConfExtnProfileNtr SheAdslLineConfNtrType
  sheAdslLineConfExtnProfileAnnexType SheAdslLineConfAnnexType
  sheAdslLineConfExtnProfileAlctlUsVer SheAdslLineConfExtnProfileAlctlUsVerType
  sheAdslLineConfExtnProfileUseCustomBin SheAdslLineConfEnableSpecial2Type
  sheAdslLineConfExtnProfileDnBinUsage OCTET STRING
  sheAdslLineConfExtnProfileMaxDCo SheAdslLineConfIntDephtType
  sheAdslLineConfExtnProfileFullRetrain SheAdslLineConfEnableSpecial3Type
  sheAdslLineConfExtnProfileAdvertisedCapabilities SheAdslLineConfAdvertisedCapabilitiesType
  sheAdslLineConfExtnProfilePsdMaskType SheAdslLineConfPsdMaskType
  sheAdslLineConfExtnProfileLineDmtConfMode SheAdslLineConfLineDmtConfModeType
  sheAdslLineConfExtnProfileEraseProfiles SheAdslLineConfEnableSpecial2Type
  sheAdslLineConfExtnProfileRsMemory SheAdslLineConfRsMemoryType
  sheAdslLineConfExtnProfileParamHybridLossTestStart INTEGER
  sheAdslLineConfExtnProfileParamHybridLossTestEnd INTEGER
  sheAdslLineConfExtnProfileConfMinInp SheAdslConfMinInpType
  sheAdslLineConfExtnProfileRfiBandMask OCTET STRING
  sheAdslLineConfExtnProfileUpstreamPsdMaskSelection SheAdslLineConfUpstreamPSDMaskSelectionType
  sheAdslLineConfExtnProfileMaxNomPsdDs INTEGER
  sheAdslLineConfExtnProfileMaxNomAtpDs Gauge32
  sheAdslLineConfExtnProfilePsdMaskDs OCTET STRING
  sheAdslLineConfExtnProfilePSDMASKdsEnable SheAdslLineConfEnableType
  sheAdslLineConfExtnProfileConfMinInpUs SheAdslConfMinInpType

SheAdslLineEntry  
SEQUENCE    
  sheAdslLineCoding AdslLineCodingType
  sheAdslLineType SheAdslConfLineType
  sheAdslLineSpecific VariablePointer
  sheAdslLineConfProfile SnmpAdminString
  sheAdslLineAlarmConfProfile SnmpAdminString
  sheAdslLineAction SheAdslLineActionType
  sheAdslLineLineDmtTrellis SheAdslLineTrellisModeType
  sheAdslLineUtopiaL2RxAddr INTEGER
  sheAdslLineUtopiaL2TxAddr INTEGER
  sheAdslLineClockType SheAdslLineClockType
  sheAdslLineAtucCapability SheAdslAtuxCapabilityType
  sheAdslLineAturCapability SheAdslAtuxCapabilityType
  sheAdslLineAtuActualCapability SheAdslAtuxCapabilityType
  sheAdslLinePwrMgmtPMSF SheAdslPwrMgmtPMSFType
  sheAdslLineDeltConfLDSF SheAdslLineDeltConfLDSFType
  sheAdslLineRfiBandMask OCTET STRING
  sheAdslLineDpboProfile SnmpAdminString

SheAdslAtucPhysEntry  
SEQUENCE    
  sheAdslAtucPhysInvSerialNumber SnmpAdminString
  sheAdslAtucPhysInvVendorID SnmpAdminString
  sheAdslAtucPhysInvVersionNumber SnmpAdminString
  sheAdslAtucPhysCurrSnrMgn INTEGER
  sheAdslAtucPhysCurrAtn Gauge32
  sheAdslAtucPhysCurrStatus SheAdslLineCurrentStatusType
  sheAdslAtucPhysCurrOutputPwr INTEGER
  sheAdslAtucPhysCurrAttainableRate Gauge32
  sheAdslAtucPhysOpState SheAdslLineOpStateType
  sheAdslAtucPhysActualStd SheAdslLineConfStandardType
  sheAdslAtucPhysBertError Unsigned32
  sheAdslAtucPhysTxAtmCellCounter Counter32
  sheAdslAtucPhysRxAtmCellCounter Unsigned32
  sheAdslAtucPhysStartProgress Unsigned32
  sheAdslAtucPhysIdleBertError Unsigned32
  sheAdslAtucPhysIdleBertCells Unsigned32
  sheAdslAtucPhysBertSync SheAdslAtucPhysBertSyncType
  sheAdslAtucPhysParametricTestResult SheAdslAtucPhysParametricTestResultType
  sheAdslAtucPwrMgmtState SheAdslPwrMgmtStateType
  sheAdslAtucPhysDeltHLINSCus Unsigned32
  sheAdslAtucPhysDeltHLINpsus OCTET STRING
  sheAdslAtucPhysDeltHLOGMTus Unsigned32
  sheAdslAtucPhysDeltHLOGpsus OCTET STRING
  sheAdslAtucPhysDeltQLNMTus Unsigned32
  sheAdslAtucPhysDeltQLNpsus OCTET STRING
  sheAdslAtucPhysActState SheAdslLineActStateType
  sheAdslAtucPhysCurrentBinStatus OCTET STRING
  sheAdslAtucPhysCurrentBinBitLoading OCTET STRING
  sheAdslAtucPhysDeltSNRMTus Unsigned32
  sheAdslAtucPhysDeltDMTBinSNRus OCTET STRING
  sheAdslAtucPhysDeltLastTxState SheAdslPhysAtucDeltLastTxStateType
  sheAdslAtucPhysDeltSATNus Unsigned32

SheAdslAtucChanEntry  
SEQUENCE    
  sheAdslAtucChanInterleaveDelay Gauge32
  sheAdslAtucChanCurrTxRate Gauge32
  sheAdslAtucChanPrevTxRate Gauge32
  sheAdslAtucChanCrcBlockLength Gauge32
  sheAdslAtucChanCurrAtmStatus SheAdslLineAtmStatus
  sheAdslAtucChanRsSymbols Unsigned32
  sheAdslAtucChanRsDepth Unsigned32
  sheAdslAtucChanRsRedundancy Unsigned32

SheAdslAtucPerfDataEntry  
SEQUENCE    
  sheAdslAtucPerfDataLofs Counter32
  sheAdslAtucPerfDataLoss Counter32
  sheAdslAtucPerfDataLols Counter32
  sheAdslAtucPerfDataLprs Counter32
  sheAdslAtucPerfDataESs Counter32
  sheAdslAtucPerfDataInits Counter32
  sheAdslAtucPerfDataStatFastR Gauge32
  sheAdslAtucPerfDataStatFailedFastR Gauge32
  sheAdslAtucPerfDataStatSesL Gauge32
  sheAdslAtucPerfDataStatUasL Gauge32
  sheAdslAtucPerfDataValidIntervals INTEGER
  sheAdslAtucPerfDataInvalidIntervals INTEGER
  sheAdslAtucPerfDataCurr15MinTimeElapsed AdslPerfTimeElapsed
  sheAdslAtucPerfDataCurr15MinLofs PerfCurrentCount
  sheAdslAtucPerfDataCurr15MinLoss PerfCurrentCount
  sheAdslAtucPerfDataCurr15MinLols PerfCurrentCount
  sheAdslAtucPerfDataCurr15MinLprs PerfCurrentCount
  sheAdslAtucPerfDataCurr15MinESs PerfCurrentCount
  sheAdslAtucPerfDataCurr15MinInits PerfCurrentCount
  sheAdslAtucPerfDataCurr15MinFastR Gauge32
  sheAdslAtucPerfDataCurr15MinFailedFastR Gauge32
  sheAdslAtucPerfDataCurr15MinSesL Gauge32
  sheAdslAtucPerfDataCurr15MinUasL Gauge32
  sheAdslAtucPerfDataCurr1DayTimeElapsed AdslPerfTimeElapsed
  sheAdslAtucPerfDataCurr1DayLofs AdslPerfCurrDayCount
  sheAdslAtucPerfDataCurr1DayLoss AdslPerfCurrDayCount
  sheAdslAtucPerfDataCurr1DayLols AdslPerfCurrDayCount
  sheAdslAtucPerfDataCurr1DayLprs AdslPerfCurrDayCount
  sheAdslAtucPerfDataCurr1DayESs AdslPerfCurrDayCount
  sheAdslAtucPerfDataCurr1DayInits AdslPerfCurrDayCount
  sheAdslAtucPerfDataCurr1DayFastR Gauge32
  sheAdslAtucPerfDataCurr1DayFailedFastR Gauge32
  sheAdslAtucPerfDataCurr1DaySesL Gauge32
  sheAdslAtucPerfDataCurr1DayUasL Gauge32
  sheAdslAtucPerfDataPrev1DayTimeElapsed Gauge32
  sheAdslAtucPerfDataPrev1DayMoniSecs INTEGER
  sheAdslAtucPerfDataPrev1DayLofs AdslPerfPrevDayCount
  sheAdslAtucPerfDataPrev1DayLoss AdslPerfPrevDayCount
  sheAdslAtucPerfDataPrev1DayLols AdslPerfPrevDayCount
  sheAdslAtucPerfDataPrev1DayLprs AdslPerfPrevDayCount
  sheAdslAtucPerfDataPrev1DayESs AdslPerfPrevDayCount
  sheAdslAtucPerfDataPrev1DayInits AdslPerfPrevDayCount
  sheAdslAtucPerfDataPrev1DayFastR Gauge32
  sheAdslAtucPerfDataPrev1DayFailedFastR Gauge32
  sheAdslAtucPerfDataPrev1DaySesL Gauge32
  sheAdslAtucPerfDataPrev1DayUasL Gauge32

SheAdslAtucIntervalEntry  
SEQUENCE    
  sheAdslAtucIntervalNumber INTEGER
  sheAdslAtucIntervalValidData TruthValue
  sheAdslAtucIntervalEndTime Unsigned32
  sheAdslAtucIntervalLofs PerfIntervalCount
  sheAdslAtucIntervalLoss PerfIntervalCount
  sheAdslAtucIntervalLols PerfIntervalCount
  sheAdslAtucIntervalLprs PerfIntervalCount
  sheAdslAtucIntervalESs PerfIntervalCount
  sheAdslAtucIntervalInits PerfIntervalCount
  sheAdslAtucIntervalFastR Gauge32
  sheAdslAtucIntervalFailedFastR Gauge32
  sheAdslAtucIntervalSesL Gauge32
  sheAdslAtucIntervalUasL Gauge32

SheAdslAtucChanPerfDataEntry  
SEQUENCE    
  sheAdslAtucChanPerfDataTimeElapsed Gauge32
  sheAdslAtucChanPerfDataReceivedBlks Counter32
  sheAdslAtucChanPerfDataTransmittedBlks Counter32
  sheAdslAtucChanPerfDataCorrectedBlks Counter32
  sheAdslAtucChanPerfDataUncorrectBlks Counter32
  sheAdslAtucChanPerfDataNcd Gauge32
  sheAdslAtucChanPerfDataOcd Gauge32
  sheAdslAtucChanPerfDataHec Gauge32
  sheAdslAtucChanPerfDataValidIntervals INTEGER
  sheAdslAtucChanPerfDataInvalidIntervals INTEGER
  sheAdslAtucChanPerfDataCurr15MinTimeElapsed AdslPerfTimeElapsed
  sheAdslAtucChanPerfDataCurr15MinReceivedBlks PerfCurrentCount
  sheAdslAtucChanPerfDataCurr15MinTransmittedBlks PerfCurrentCount
  sheAdslAtucChanPerfDataCurr15MinCorrectedBlks PerfCurrentCount
  sheAdslAtucChanPerfDataCurr15MinUncorrectBlks PerfCurrentCount
  sheAdslAtucChanPerfDataCurr15MinNcd Gauge32
  sheAdslAtucChanPerfDataCurr15MinOcd Gauge32
  sheAdslAtucChanPerfDataCurr15MinHec Gauge32
  sheAdslAtucChanPerfDataCurr1DayTimeElapsed AdslPerfTimeElapsed
  sheAdslAtucChanPerfDataCurr1DayReceivedBlks AdslPerfCurrDayCount
  sheAdslAtucChanPerfDataCurr1DayTransmittedBlks AdslPerfCurrDayCount
  sheAdslAtucChanPerfDataCurr1DayCorrectedBlks AdslPerfCurrDayCount
  sheAdslAtucChanPerfDataCurr1DayUncorrectBlks AdslPerfCurrDayCount
  sheAdslAtucChanPerfDataCurr1DayNcd Gauge32
  sheAdslAtucChanPerfDataCurr1DayOcd Gauge32
  sheAdslAtucChanPerfDataCurr1DayHec Gauge32
  sheAdslAtucChanPerfDataPrev1DayMoniSecs INTEGER
  sheAdslAtucChanPerfDataPrev1DayReceivedBlks AdslPerfPrevDayCount
  sheAdslAtucChanPerfDataPrev1DayTransmittedBlks AdslPerfPrevDayCount
  sheAdslAtucChanPerfDataPrev1DayCorrectedBlks AdslPerfPrevDayCount
  sheAdslAtucChanPerfDataPrev1DayUncorrectBlks AdslPerfPrevDayCount
  sheAdslAtucChanPerfDataPrev1DayNcd Gauge32
  sheAdslAtucChanPerfDataPrev1DayOcd Gauge32
  sheAdslAtucChanPerfDataPrev1DayHec Gauge32

SheAdslAtucChanIntervalEntry  
SEQUENCE    
  sheAdslAtucChanIntervalNumber INTEGER
  sheAdslAtucChanIntervalValidData TruthValue
  sheAdslAtucChanIntervalEndTime Unsigned32
  sheAdslAtucChanIntervalReceivedBlks PerfIntervalCount
  sheAdslAtucChanIntervalTransmittedBlks PerfIntervalCount
  sheAdslAtucChanIntervalCorrectedBlks PerfIntervalCount
  sheAdslAtucChanIntervalUncorrectBlks PerfIntervalCount
  sheAdslAtucChanIntervalNcd Counter32
  sheAdslAtucChanIntervalOcd Counter32
  sheAdslAtucChanIntervalHec Counter32

SheAdslAturPhysEntry  
SEQUENCE    
  sheAdslAturPhysInvSerialNumber SnmpAdminString
  sheAdslAturPhysInvVendorID SnmpAdminString
  sheAdslAturPhysInvVersionNumber SnmpAdminString
  sheAdslAturPhysCurrSnrMgn INTEGER
  sheAdslAturPhysCurrAtn Gauge32
  sheAdslAturPhysCurrStatus SheAdslLineCurrentStatusType
  sheAdslAturPhysCurrOutputPwr INTEGER
  sheAdslAturPhysCurrAttainableRate Gauge32
  sheAdslAturPhysConfig OCTET STRING
  sheAdslAturPhysDeltHLINSCds Unsigned32
  sheAdslAturPhysDeltHLINpsds OCTET STRING
  sheAdslAturPhysDeltHLOGMTds Unsigned32
  sheAdslAturPhysDeltHLOGpsds OCTET STRING
  sheAdslAturPhysDeltQLNMTds Unsigned32
  sheAdslAturPhysDeltQLNpsds OCTET STRING
  sheAdslAturPhysCurrentBinBitLoading OCTET STRING
  sheAdslAturPhysDeltSNRMTds Unsigned32
  sheAdslAturPhysDeltDMTBinSNRds OCTET STRING
  sheAdslAturPhysDeltLastTxState SheAdslPhysAturDeltLastTxStateType
  sheAdslAturPhysDeltSATNds Unsigned32

SheAdslAturChanEntry  
SEQUENCE    
  sheAdslAturChanInterleaveDelay Gauge32
  sheAdslAturChanCurrTxRate Gauge32
  sheAdslAturChanPrevTxRate Gauge32
  sheAdslAturChanCrcBlockLength Gauge32
  sheAdslAturChanCurrAtmStatus SheAdslLineAtmStatus
  sheAdslAturChanRsSymbols Unsigned32
  sheAdslAturChanRsDepth Unsigned32
  sheAdslAturChanRsRedundancy Unsigned32

SheAdslAturPerfDataEntry  
SEQUENCE    
  sheAdslAturPerfDataLofs Counter32
  sheAdslAturPerfDataLoss Counter32
  sheAdslAturPerfDataLprs Counter32
  sheAdslAturPerfDataESs Counter32
  sheAdslAturPerfDataStatSesL Counter32
  sheAdslAturPerfDataStatUasL Counter32
  sheAdslAturPerfDataValidIntervals INTEGER
  sheAdslAturPerfDataInvalidIntervals INTEGER
  sheAdslAturPerfDataCurr15MinTimeElapsed AdslPerfTimeElapsed
  sheAdslAturPerfDataCurr15MinLofs PerfCurrentCount
  sheAdslAturPerfDataCurr15MinLoss PerfCurrentCount
  sheAdslAturPerfDataCurr15MinLprs PerfCurrentCount
  sheAdslAturPerfDataCurr15MinESs PerfCurrentCount
  sheAdslAturPerfDataCurr15MinSesL PerfCurrentCount
  sheAdslAturPerfDataCurr15MinUasL PerfCurrentCount
  sheAdslAturPerfDataCurr1DayTimeElapsed AdslPerfTimeElapsed
  sheAdslAturPerfDataCurr1DayLofs AdslPerfCurrDayCount
  sheAdslAturPerfDataCurr1DayLoss AdslPerfCurrDayCount
  sheAdslAturPerfDataCurr1DayLprs AdslPerfCurrDayCount
  sheAdslAturPerfDataCurr1DayESs AdslPerfCurrDayCount
  sheAdslAturPerfDataCurr1DaySesL AdslPerfCurrDayCount
  sheAdslAturPerfDataCurr1DayUasL AdslPerfCurrDayCount
  sheAdslAturPerfDataPrev1DayMoniSecs INTEGER
  sheAdslAturPerfDataPrev1DayLofs AdslPerfPrevDayCount
  sheAdslAturPerfDataPrev1DayLoss AdslPerfPrevDayCount
  sheAdslAturPerfDataPrev1DayLprs AdslPerfPrevDayCount
  sheAdslAturPerfDataPrev1DayESs AdslPerfPrevDayCount
  sheAdslAturPerfDataPrev1DaySesL AdslPerfPrevDayCount
  sheAdslAturPerfDataPrev1DayUasL AdslPerfPrevDayCount

SheAdslAturIntervalEntry  
SEQUENCE    
  sheAdslAturIntervalNumber INTEGER
  sheAdslAturIntervalValidData TruthValue
  sheAdslAturIntervalEndTime Unsigned32
  sheAdslAturIntervalLofs PerfIntervalCount
  sheAdslAturIntervalLoss PerfIntervalCount
  sheAdslAturIntervalLprs PerfIntervalCount
  sheAdslAturIntervalESs PerfIntervalCount
  sheAdslAturIntervalSesL PerfIntervalCount
  sheAdslAturIntervalUasL PerfIntervalCount

SheAdslAturChanPerfDataEntry  
SEQUENCE    
  sheAdslAturChanPerfDataReceivedBlks Counter32
  sheAdslAturChanPerfDataTransmittedBlks Counter32
  sheAdslAturChanPerfDataCorrectedBlks Counter32
  sheAdslAturChanPerfDataUncorrectBlks Counter32
  sheAdslAturChanPerfDataExtnNcd Gauge32
  sheAdslAturChanPerfDataExtnHec Gauge32
  sheAdslAturChanPerfDataPerfValidIntervals INTEGER
  sheAdslAturChanPerfDataPerfInvalidIntervals INTEGER
  sheAdslAturChanPerfDataCurr15MinTimeElapsed AdslPerfTimeElapsed
  sheAdslAturChanPerfDataCurr15MinReceivedBlks PerfCurrentCount
  sheAdslAturChanPerfDataCurr15MinTransmittedBlks PerfCurrentCount
  sheAdslAturChanPerfDataCurr15MinCorrectedBlks PerfCurrentCount
  sheAdslAturChanPerfDataCurr15MinUncorrectBlks PerfCurrentCount
  sheAdslAturChanPerfDataExtnCurr15MinNcd Gauge32
  sheAdslAturChanPerfDataExtnCurr15MinHec Gauge32
  sheAdslAturChanPerfDataCurr1DayTimeElapsed AdslPerfTimeElapsed
  sheAdslAturChanPerfDataCurr1DayReceivedBlks AdslPerfCurrDayCount
  sheAdslAturChanPerfDataCurr1DayTransmittedBlks AdslPerfCurrDayCount
  sheAdslAturChanPerfDataCurr1DayCorrectedBlks AdslPerfCurrDayCount
  sheAdslAturChanPerfDataCurr1DayUncorrectBlks AdslPerfCurrDayCount
  sheAdslAturChanPerfDataExtnCurr1DayNcd Gauge32
  sheAdslAturChanPerfDataExtnCurr1DayHec Gauge32
  sheAdslAturChanPerfDataPrev1DayMoniSecs INTEGER
  sheAdslAturChanPerfDataPrev1DayReceivedBlks AdslPerfPrevDayCount
  sheAdslAturChanPerfDataPrev1DayTransmittedBlks AdslPerfPrevDayCount
  sheAdslAturChanPerfDataPrev1DayCorrectedBlks AdslPerfPrevDayCount
  sheAdslAturChanPerfDataPrev1DayUncorrectBlks AdslPerfPrevDayCount
  sheAdslAturChanPerfDataExtnPrev1DayNcd Gauge32
  sheAdslAturChanPerfDataExtnPrev1DayHec Gauge32

SheAdslAturChanIntervalEntry  
SEQUENCE    
  sheAdslAturChanIntervalNumber INTEGER
  sheAdslAturChanIntervalValidData TruthValue
  sheAdslAturChanIntervalEndTime Unsigned32
  sheAdslAturChanIntervalReceivedBlks PerfIntervalCount
  sheAdslAturChanIntervalTransmittedBlks PerfIntervalCount
  sheAdslAturChanIntervalCorrectedBlks PerfIntervalCount
  sheAdslAturChanIntervalUncorrectBlks PerfIntervalCount
  sheAdslAturChanIntervalNcd Gauge32
  sheAdslAturChanIntervalHec Gauge32

SheAdslLineAlarmConfProfileEntry  
SEQUENCE    
  sheAdslLineAlarmConfProfileIndex Integer32
  sheAdslLineAlarmConfProfileName SnmpAdminString
  sheAdslLineAlarmConfProfileOpStateTrapEnable TruthValue
  sheAdslLineAlarmConfProfileAtucThreshFastRateUp Unsigned32
  sheAdslLineAlarmConfProfileAtucThreshInterleaveRateUp Unsigned32
  sheAdslLineAlarmConfProfileAtucThreshFastRateDown Unsigned32
  sheAdslLineAlarmConfProfileAtucThreshInterleaveRateDown Unsigned32
  sheAdslLineAlarmConfProfileAtucInitFailureTrapEnable TruthValue
  sheAdslLineAlarmConfProfileAtucThresh15MinLofs INTEGER
  sheAdslLineAlarmConfProfileAtucThresh15MinLoss INTEGER
  sheAdslLineAlarmConfProfileAtucThresh15MinLols INTEGER
  sheAdslLineAlarmConfProfileAtucThresh15MinLprs INTEGER
  sheAdslLineAlarmConfProfileAtucThresh15MinESs INTEGER
  sheAdslLineAlarmConfProfileAtucThresh15MinSesL INTEGER
  sheAdslLineAlarmConfProfileAtucThresh15MinUasL INTEGER
  sheAdslLineAlarmConfProfileAtucThresh15MinFailFastR INTEGER
  sheAdslLineAlarmConfProfileAturThreshFastRateUp Unsigned32
  sheAdslLineAlarmConfProfileAturThreshInterleaveRateUp Unsigned32
  sheAdslLineAlarmConfProfileAturThreshFastRateDown Unsigned32
  sheAdslLineAlarmConfProfileAturThreshInterleaveRateDown Unsigned32
  sheAdslLineAlarmConfProfileAturThresh15MinLofs INTEGER
  sheAdslLineAlarmConfProfileAturThresh15MinLoss INTEGER
  sheAdslLineAlarmConfProfileAturThresh15MinLprs INTEGER
  sheAdslLineAlarmConfProfileAturThresh15MinESs INTEGER
  sheAdslLineAlarmConfProfileAturThresh15MinSesL INTEGER
  sheAdslLineAlarmConfProfileAturThresh15MinUasL INTEGER

SheAdslVccTpEntry  
SEQUENCE    
  sheAdslVccTpIndex Integer32
  sheAdslVccTpSubLayerIndex InterfaceIndex
  sheAdslVccTpNumber Integer32
  sheAdslVccTpVpi Integer32
  sheAdslVccTpVci Integer32
  sheAdslVccTpOamLevel SheAdslOamLevelType
  sheAdslVccTpLoopTest SheAdslOamLoopTestType
  sheAdslVccTpLoopTestResult SheAdslVccTpLoopTestResultType
  sheAdslVccTpLoopLocId OCTET STRING
  sheAdslVccTpAlarmSeverityIndex SheAlarmSevProfileIndex
  sheAdslVccTpEgressQosClass SheAdslAtmQosType
  sheAdslVccTpEgressPeakCellRate Unsigned32
  sheAdslVccTpEgressSustainedCellRate Unsigned32
  sheAdslVccTpEgressMaxBurstSize Unsigned32
  sheAdslVccTpEgressWeight Integer32
  sheAdslVccTpIngressSustainedCellRate Unsigned32
  sheAdslVccTpIngressMaxBurstSize Unsigned32
  sheAdslVccTpAdminState SheAdslEnableType
  sheAdslVccTpOrl Unsigned32
  sheAdslVccTpUsedDslChannel SheAdslConfLineType
  sheAdslVccTpEncapsulation SheAdslAtmEncapType

SheAdslRfiBandEntry  
SEQUENCE    
  sheAdslRfiBandIndex Integer32
  sheAdslRfiBandName OCTET STRING
  sheAdslRfiBandStartTone Integer32
  sheAdslRfiBandStopTone Integer32

SheAdslAtucDualChanEntry  
SEQUENCE    
  sheAdslAtucDualChanInterleaveDelay Gauge32
  sheAdslAtucDualChanCurrTxRate Gauge32
  sheAdslAtucDualChanPrevTxRate Gauge32
  sheAdslAtucDualChanCrcBlockLength Gauge32
  sheAdslAtucDualChanCurrAtmStatus SheAdslLineAtmStatus
  sheAdslAtucDualChanRsSymbols Unsigned32
  sheAdslAtucDualChanRsDepth Unsigned32
  sheAdslAtucDualChanRsRedundancy Unsigned32
  sheAdslAtucDualChanType SheAdslChannelType

SheAdslAturDualChanEntry  
SEQUENCE    
  sheAdslAturDualChanInterleaveDelay Gauge32
  sheAdslAturDualChanCurrTxRate Gauge32
  sheAdslAturDualChanPrevTxRate Gauge32
  sheAdslAturDualChanCrcBlockLength Gauge32
  sheAdslAturDualChanCurrAtmStatus SheAdslLineAtmStatus
  sheAdslAturDualChanRsSymbols Unsigned32
  sheAdslAturDualChanRsDepth Unsigned32
  sheAdslAturDualChanRsRedundancy Unsigned32
  sheAdslAturDualChanType SheAdslChannelType

SheAdslAtucDualChanPerfDataEntry  
SEQUENCE    
  sheAdslAtucDualChanPerfDataTimeElapsed Gauge32
  sheAdslAtucDualChanPerfDataReceivedBlks Counter32
  sheAdslAtucDualChanPerfDataTransmittedBlks Counter32
  sheAdslAtucDualChanPerfDataCorrectedBlks Counter32
  sheAdslAtucDualChanPerfDataUncorrectBlks Counter32
  sheAdslAtucDualChanPerfDataNcd Gauge32
  sheAdslAtucDualChanPerfDataOcd Gauge32
  sheAdslAtucDualChanPerfDataHec Gauge32
  sheAdslAtucDualChanPerfDataValidIntervals INTEGER
  sheAdslAtucDualChanPerfDataInvalidIntervals INTEGER
  sheAdslAtucDualChanPerfDataCurr15MinTimeElapsed AdslPerfTimeElapsed
  sheAdslAtucDualChanPerfDataCurr15MinReceivedBlks PerfCurrentCount
  sheAdslAtucDualChanPerfDataCurr15MinTransmittedBlks PerfCurrentCount
  sheAdslAtucDualChanPerfDataCurr15MinCorrectedBlks PerfCurrentCount
  sheAdslAtucDualChanPerfDataCurr15MinUncorrectBlks PerfCurrentCount
  sheAdslAtucDualChanPerfDataCurr15MinNcd Gauge32
  sheAdslAtucDualChanPerfDataCurr15MinOcd Gauge32
  sheAdslAtucDualChanPerfDataCurr15MinHec Gauge32
  sheAdslAtucDualChanPerfDataCurr1DayTimeElapsed AdslPerfTimeElapsed
  sheAdslAtucDualChanPerfDataCurr1DayReceivedBlks AdslPerfCurrDayCount
  sheAdslAtucDualChanPerfDataCurr1DayTransmittedBlks AdslPerfCurrDayCount
  sheAdslAtucDualChanPerfDataCurr1DayCorrectedBlks AdslPerfCurrDayCount
  sheAdslAtucDualChanPerfDataCurr1DayUncorrectBlks AdslPerfCurrDayCount
  sheAdslAtucDualChanPerfDataCurr1DayNcd Gauge32
  sheAdslAtucDualChanPerfDataCurr1DayOcd Gauge32
  sheAdslAtucDualChanPerfDataCurr1DayHec Gauge32
  sheAdslAtucDualChanPerfDataPrev1DayMoniSecs INTEGER
  sheAdslAtucDualChanPerfDataPrev1DayReceivedBlks AdslPerfPrevDayCount
  sheAdslAtucDualChanPerfDataPrev1DayTransmittedBlks AdslPerfPrevDayCount
  sheAdslAtucDualChanPerfDataPrev1DayCorrectedBlks AdslPerfPrevDayCount
  sheAdslAtucDualChanPerfDataPrev1DayUncorrectBlks AdslPerfPrevDayCount
  sheAdslAtucDualChanPerfDataPrev1DayNcd Gauge32
  sheAdslAtucDualChanPerfDataPrev1DayOcd Gauge32
  sheAdslAtucDualChanPerfDataPrev1DayHec Gauge32

SheAdslAturDualChanPerfDataEntry  
SEQUENCE    
  sheAdslAturDualChanPerfDataReceivedBlks Counter32
  sheAdslAturDualChanPerfDataTransmittedBlks Counter32
  sheAdslAturDualChanPerfDataCorrectedBlks Counter32
  sheAdslAturDualChanPerfDataUncorrectBlks Counter32
  sheAdslAturDualChanPerfDataExtnNcd Gauge32
  sheAdslAturDualChanPerfDataExtnHec Gauge32
  sheAdslAturDualChanPerfDataPerfValidIntervals INTEGER
  sheAdslAturDualChanPerfDataPerfInvalidIntervals INTEGER
  sheAdslAturDualChanPerfDataCurr15MinTimeElapsed AdslPerfTimeElapsed
  sheAdslAturDualChanPerfDataCurr15MinReceivedBlks PerfCurrentCount
  sheAdslAturDualChanPerfDataCurr15MinTransmittedBlks PerfCurrentCount
  sheAdslAturDualChanPerfDataCurr15MinCorrectedBlks PerfCurrentCount
  sheAdslAturDualChanPerfDataCurr15MinUncorrectBlks PerfCurrentCount
  sheAdslAturDualChanPerfDataExtnCurr15MinNcd Gauge32
  sheAdslAturDualChanPerfDataExtnCurr15MinHec Gauge32
  sheAdslAturDualChanPerfDataCurr1DayTimeElapsed AdslPerfTimeElapsed
  sheAdslAturDualChanPerfDataCurr1DayReceivedBlks AdslPerfCurrDayCount
  sheAdslAturDualChanPerfDataCurr1DayTransmittedBlks AdslPerfCurrDayCount
  sheAdslAturDualChanPerfDataCurr1DayCorrectedBlks AdslPerfCurrDayCount
  sheAdslAturDualChanPerfDataCurr1DayUncorrectBlks AdslPerfCurrDayCount
  sheAdslAturDualChanPerfDataExtnCurr1DayNcd Gauge32
  sheAdslAturDualChanPerfDataExtnCurr1DayHec Gauge32
  sheAdslAturDualChanPerfDataPrev1DayMoniSecs INTEGER
  sheAdslAturDualChanPerfDataPrev1DayReceivedBlks AdslPerfPrevDayCount
  sheAdslAturDualChanPerfDataPrev1DayTransmittedBlks AdslPerfPrevDayCount
  sheAdslAturDualChanPerfDataPrev1DayCorrectedBlks AdslPerfPrevDayCount
  sheAdslAturDualChanPerfDataPrev1DayUncorrectBlks AdslPerfPrevDayCount
  sheAdslAturDualChanPerfDataExtnPrev1DayNcd Gauge32
  sheAdslAturDualChanPerfDataExtnPrev1DayHec Gauge32

SheAdslAtucDualChanIntervalEntry  
SEQUENCE    
  sheAdslAtucDualChanIntervalNumber INTEGER
  sheAdslAtucDualChanIntervalValidData TruthValue
  sheAdslAtucDualChanIntervalEndTime Unsigned32
  sheAdslAtucDualChanIntervalReceivedBlks PerfIntervalCount
  sheAdslAtucDualChanIntervalTransmittedBlks PerfIntervalCount
  sheAdslAtucDualChanIntervalCorrectedBlks PerfIntervalCount
  sheAdslAtucDualChanIntervalUncorrectBlks PerfIntervalCount
  sheAdslAtucDualChanIntervalNcd Counter32
  sheAdslAtucDualChanIntervalOcd Counter32
  sheAdslAtucDualChanIntervalHec Counter32

SheAdslAturDualChanIntervalEntry  
SEQUENCE    
  sheAdslAturDualChanIntervalNumber INTEGER
  sheAdslAturDualChanIntervalValidData TruthValue
  sheAdslAturDualChanIntervalEndTime Unsigned32
  sheAdslAturDualChanIntervalReceivedBlks PerfIntervalCount
  sheAdslAturDualChanIntervalTransmittedBlks PerfIntervalCount
  sheAdslAturDualChanIntervalCorrectedBlks PerfIntervalCount
  sheAdslAturDualChanIntervalUncorrectBlks PerfIntervalCount
  sheAdslAturDualChanIntervalNcd Gauge32
  sheAdslAturDualChanIntervalHec Gauge32

SheAdslLineDpboProfileEntry  
SEQUENCE    
  sheAdslLineDpboProfileIndex Integer32
  sheAdslLineDpboProfileName OCTET STRING
  sheAdslLineDpboProfileEsel Unsigned32
  sheAdslLineDpboProfileEselMin Unsigned32
  sheAdslLineDpboProfileMus Unsigned32
  sheAdslLineDpboProfileMof Unsigned32
  sheAdslLineDpboProfileFMin Unsigned32
  sheAdslLineDpboProfileFMax Unsigned32
  sheAdslLineDpboProfileEpsd OCTET STRING
  sheAdslLineDpboProfileEScmA Unsigned32
  sheAdslLineDpboProfileEScmB Unsigned32
  sheAdslLineDpboProfileEScmC Unsigned32

SheAdslVccTpPerformanceEntry  
SEQUENCE    
  sheAdslVccTpIngressUnicastPackets Counter32
  sheAdslVccTpIngressMulticastPackets Counter32
  sheAdslVccTpIngressBroadcastPackets Counter32
  sheAdslVccTpIngressDiscardPackets Counter32
  sheAdslVccTpEgressUnicastPackets Counter32
  sheAdslVccTpEgressMulticastPackets Counter32
  sheAdslVccTpEgressBroadcastPackets Counter32
  sheAdslVccTpEgressDiscardPackets Counter32

Defined Values

sheAdslMib 1.3.6.1.4.1.231.7.1.2.1.6
The MIB module to describe ADSL product. The MIB module that provides objects that are proprietary and extension to ADSL- LINE-MIB.The MIB includes the following Tables. 1.) adslLineTable 2.) adslAtucPhysTable 3.) adslAturPhysTable 4.) adslAtucChanTable 5.) adslAturChanTable 6.) adslAtucPerfDataTable 7.) adslAtucIntervalTable 8.) adslAtucChanPerfDataTable 9.) adslAturChanPerfDataTable 10.) adslAtucChanIntervalTable 11.) adslAturChanIntervalTable 12.) adslLineConfProfileTable 13.) adslLineConfExtnProfileTable 13.) adslLineAlarmConfProfileTable 14.) adslVccTpTable 15.) adslRfiMaskTable
MODULE-IDENTITY    

sheAdslMibObjects 1.3.6.1.4.1.231.7.1.2.1.6.1
OBJECT IDENTIFIER    

sheAdslLineMIB 1.3.6.1.4.1.231.7.1.2.1.6.1.1
OBJECT IDENTIFIER    

sheDslSystemParamGroup 1.3.6.1.4.1.231.7.1.2.1.6.1.1.1
OBJECT IDENTIFIER    

sheDslSystemDslType 1.3.6.1.4.1.231.7.1.2.1.6.1.1.1.1
This object identifies the firmware to be downloaded. adsl(1), sdsl(2), shdsl(3)
OBJECT-TYPE    
  SheDslSystemType  

sheDslSystemLineCodingType 1.3.6.1.4.1.231.7.1.2.1.6.1.1.1.2
This object indicates ADSL line code type. other(1), dmt(2), cap(3), qam(4)
OBJECT-TYPE    
  SheDslSystemLineCodingType  

sheDslSystemLineTxCfg 1.3.6.1.4.1.231.7.1.2.1.6.1.1.1.3
This object indicates transmission capabilities with which the DSL system is configured. unused(0), etsi(1), q9921PotsNonOverlapped(2), q9921PotsOverlapped(3), q9921IsdnNonOverlapped(4), q9921IsdnOverlapped(5), q9921TcmIsdnNonOverlapped(6), q9921TcmIsdnOverlapped(7), q9922PotsNonOverlapped(8), q9922PotsOverlapped(9), q9922TcmIsdnNonOverlapped(10), q9922TcmIsdnOverlapped(11), q9922TcmIsdnSymmetric(12), adslPlusPotsNonOverlapped(13)
OBJECT-TYPE    
  SheDslSystemTxCfgType  

sheDslSystemParamControl 1.3.6.1.4.1.231.7.1.2.1.6.1.1.2
OBJECT IDENTIFIER    

sheDslSystemParamControlRequest 1.3.6.1.4.1.231.7.1.2.1.6.1.1.2.1
setDslSystemLineTxCfg: sheDslSystemParamControlLineTxCfg
OBJECT-TYPE    
  SheAdslControlRequestType  

sheDslSystemParamControlStatus 1.3.6.1.4.1.231.7.1.2.1.6.1.1.2.2
The status of a user command.
OBJECT-TYPE    
  SheControlStatusType  

sheDslSystemParamControlTimer 1.3.6.1.4.1.231.7.1.2.1.6.1.1.2.3
The maximum wait time for the manager for a long running user command.
OBJECT-TYPE    
  Gauge32  

sheDslSystemParamControlReqResult 1.3.6.1.4.1.231.7.1.2.1.6.1.1.2.4
The result of the last user command.
OBJECT-TYPE    
  SheAdslControlRequestResultType  

sheDslSystemParamControlTimeStamp 1.3.6.1.4.1.231.7.1.2.1.6.1.1.2.5
The time stamp of the last command (end of command).
OBJECT-TYPE    
  Unsigned32  

sheDslSystemParamControlLineTxCfg 1.3.6.1.4.1.231.7.1.2.1.6.1.1.2.6
This object indicates transmission capabilities with which the DSL system is configured.
OBJECT-TYPE    
  SheDslSystemTxCfgType  

sheAdslSystemCapabilityGroup 1.3.6.1.4.1.231.7.1.2.1.6.1.1.3
OBJECT IDENTIFIER    

sheAdslCapabilityLineTxCap 1.3.6.1.4.1.231.7.1.2.1.6.1.1.3.1
This bitmap specifies all transmission modes, which the ATU-C is capable of supporting. Right now support for Annex A (q9921PotsNonOverlapped(2) and q9921PotsOverlapped(3)) is present. This value depends on the DSL PHY firmware present on Columbia MND unused(0), etsi(1), q9921PotsNonOverlapped(2), q9921PotsOverlapped(3), q9921IsdnNonOverlapped(4), q9921IsdnOverlapped(5), q9921TcmIsdnNonOverlapped(6), q9921TcmIsdnOverlapped(7), q9922PotsNonOverlapped(8), q9922PotsOverlapped(9), q9922TcmIsdnNonOverlapped(10), q9922TcmIsdnOverlapped(11), q9922TcmIsdnSymmetric(12), adslPlusPotsNonOverlapped(13)
OBJECT-TYPE    
  SheDslSystemTxCfgType  

sheAdslLineConfProfileTable 1.3.6.1.4.1.231.7.1.2.1.6.1.1.4
This table contains information on the ADSL line configuration. One entry in this table reflects a profile defined by a manager which can be used to configure the ADSL line.
OBJECT-TYPE    
  SEQUENCE OF  
    SheAdslLineConfProfileEntry

sheAdslLineConfProfileEntry 1.3.6.1.4.1.231.7.1.2.1.6.1.1.4.1
Each entry consists of a list of parameters that represents the configuration of an ADSL modem. `Dynamic' profiles are implemented. A default profile will always exist. This profile's name will be set to `DEFVAL' and its parameters will be set to vendor specific values, unless otherwise specified in this document.
OBJECT-TYPE    
  SheAdslLineConfProfileEntry  

sheAdslLineConfProfileIndex 1.3.6.1.4.1.231.7.1.2.1.6.1.1.4.1.1
The table index.
OBJECT-TYPE    
  Integer32 1..300  

sheAdslLineConfProfileName 1.3.6.1.4.1.231.7.1.2.1.6.1.1.4.1.2
This object is used by the line configuration table in order to identify a row of this table. Dynamic profiles are implemented. The profile name is user specified. Also, the system will always provide a default profile whose name is `DEFVAL' for Annex A and DEFVAL_ISDN fpr Annex B card's (both Adsl2+). Special characters are not allowed, like: space : ?
OBJECT-TYPE    
  SnmpAdminString Size(1..32)  

sheAdslLineConfProfileAtucConfRateMode 1.3.6.1.4.1.231.7.1.2.1.6.1.1.4.1.3
Defines what form of transmit rate adaptation is configured on this modem. See ADSL Forum TR-005 [3] for more information. fixed(1), adaptAtStartup(2), adaptAtRuntime(3)
OBJECT-TYPE    
  SheAdslLineConfRateModeType  

sheAdslLineConfProfileAtucConfRateChanRatio 1.3.6.1.4.1.231.7.1.2.1.6.1.1.4.1.4
Configured allocation ratio of excess transmit bandwidth between fast and interleaved channels. Only applies when two channel mode and rate adaptive DSL are supported. A ratio of 20% means, that 20 % of the available data rate (in access of the minimum rate summend over all bearer channels) will be assigned to the fast channel and 80% to the interleaved channel. Only valid if sheAdslLineConfExtnProfileLineType is set to dualLatency mode.
OBJECT-TYPE    
  INTEGER 0..100  

sheAdslLineConfProfileAtucConfTargetSnrMgn 1.3.6.1.4.1.231.7.1.2.1.6.1.1.4.1.5
Configured Target Signal/Noise Margin. This is the Noise Margin the modem must achieve with a BER of 10-7 or better to successfully complete initialization.
OBJECT-TYPE    
  INTEGER 0..310  

sheAdslLineConfProfileAtucConfMaxSnrMgn 1.3.6.1.4.1.231.7.1.2.1.6.1.1.4.1.6
Configured Maximum acceptable Signal/Noise Margin. If the Noise Margin is above this the modem should attempt to reduce its power output to optimize its operation.
OBJECT-TYPE    
  INTEGER 0..310  

sheAdslLineConfProfileAtucConfMinSnrMgn 1.3.6.1.4.1.231.7.1.2.1.6.1.1.4.1.7
Configured Minimum acceptable Signal/Noise Margin. If the noise margin falls below this level, the modem should attempt to increase its power output. If that is not possible the modem will attempt to re-initialize or shut down.
OBJECT-TYPE    
  INTEGER 0..310  

sheAdslLineConfProfileAtucConfDownshiftSnrMgn 1.3.6.1.4.1.231.7.1.2.1.6.1.1.4.1.8
Configured Signal/Noise Margin for rate downshift. If the noise margin falls below this level, the modem should attempt to decrease its transmit rate. In the case that adaptAtRuntime mode is not present, the value will be 'don't care'.
OBJECT-TYPE    
  INTEGER 0..310  

sheAdslLineConfProfileAtucConfUpshiftSnrMgn 1.3.6.1.4.1.231.7.1.2.1.6.1.1.4.1.9
Configured Signal/Noise Margin for rate upshift. If the noise margin rises above this level, the modem should attempt to increase its transmit rate. In the case that adaptAtRuntime mode is not present, the value will be 'don't care'.
OBJECT-TYPE    
  INTEGER 0..310  

sheAdslLineConfProfileAtucConfMinUpshiftTime 1.3.6.1.4.1.231.7.1.2.1.6.1.1.4.1.10
Minimum time that the current margin is above UpshiftSnrMgn before an upshift occurs. In the case that adaptAtRuntime mode is not present, the value will be 'don't care'.
OBJECT-TYPE    
  INTEGER 0..16383  

sheAdslLineConfProfileAtucConfMinDownshiftTime 1.3.6.1.4.1.231.7.1.2.1.6.1.1.4.1.11
Minimum time that the current margin is below DownshiftSnrMgn before a downshift occurs. In the case that adaptAtRuntime mode is not present, the value will be 'don't care'.
OBJECT-TYPE    
  INTEGER 0..16383  

sheAdslLineConfProfileAtucChanConfFastMinTxRate 1.3.6.1.4.1.231.7.1.2.1.6.1.1.4.1.12
Configured Minimum Transmit rate for `Fast' channels, in kbps. See adslAtucConfRateChanRatio for information regarding RADSL mode and ATUR transmit rate for ATUC receive rates. Only multiples of 32 will be configured.
OBJECT-TYPE    
  Unsigned32 32..32736  

sheAdslLineConfProfileAtucChanConfInterleaveMinTxRate 1.3.6.1.4.1.231.7.1.2.1.6.1.1.4.1.13
Configured Minimum Transmit rate for `Interleave' channels, in kbps. See adslAtucConfRateChanRatio for information regarding RADSL mode and see ATUR transmit rate for receive rates. Only multiples of 32 will be configured.
OBJECT-TYPE    
  Unsigned32 32..32736  

sheAdslLineConfProfileAtucChanConfFastMaxTxRate 1.3.6.1.4.1.231.7.1.2.1.6.1.1.4.1.14
Configured Maximum Transmit rate for `Fast' channels, in kbps. See adslAtucConfRateChanRatio for information regarding RADSL mode and see ATUR transmit rate for ATUC receive rates. Only multiples of 32 will be configured.
OBJECT-TYPE    
  Unsigned32 32..32736  

sheAdslLineConfProfileAtucChanConfInterleaveMaxTxRate 1.3.6.1.4.1.231.7.1.2.1.6.1.1.4.1.15
Configured Maximum Transmit rate for `Interleave' channels, in kbps. See adslAtucConfRateChanRatio for information regarding RADSL mode and ATUR transmit rate for ATUC receive rates. Only multiples of 32 will be configured.
OBJECT-TYPE    
  Unsigned32 32..32736  

sheAdslLineConfProfileAtucChanConfMaxInterleaveDelay 1.3.6.1.4.1.231.7.1.2.1.6.1.1.4.1.16
Configured maximum Interleave Delay for this channel. Interleave delay applies only to the interleave channel and defines the mapping (relative spacing) between subsequent input bytes at the interleaver input and their placement in the bit stream at the interleaver output. Larger numbers provide greater separation between consecutive input bytes in the output bit stream allowing for improved impulse noise immunity at the expense of payload latency.
OBJECT-TYPE    
  INTEGER 1..63  

sheAdslLineConfProfileAturConfRateMode 1.3.6.1.4.1.231.7.1.2.1.6.1.1.4.1.17
Defines what form of transmit rate adaptation is configured on this modem. See ADSL Forum TR-005 [3] for more information. fixed(1), adaptAtStartup(2), adaptAtRuntime(3)
OBJECT-TYPE    
  SheAdslLineConfRateModeType  

sheAdslLineConfProfileAturConfRateChanRatio 1.3.6.1.4.1.231.7.1.2.1.6.1.1.4.1.18
Configured allocation ratio of excess transmit bandwidth between fast and interleaved channels. Only applies when two channel mode and rate adaptive DSL are supported. A ratio of 20% means, that 20 % of the available data rate (in access of the minimum rate summend over all bearer channels) will be assigned to the fast channel and 80% to the interleaved channel. Only valid if sheAdslLineConfExtnProfileLineType is set to dualLatency mode.
OBJECT-TYPE    
  INTEGER 0..100  

sheAdslLineConfProfileAturConfTargetSnrMgn 1.3.6.1.4.1.231.7.1.2.1.6.1.1.4.1.19
Configured Target Signal/Noise Margin. This is the Noise Margin the modem must achieve with a BER of 10-7 or better to successfully complete initialization.
OBJECT-TYPE    
  INTEGER 0..310  

sheAdslLineConfProfileAturConfMaxSnrMgn 1.3.6.1.4.1.231.7.1.2.1.6.1.1.4.1.20
Configured Maximum acceptable Signal/Noise Margin. If the Noise Margin is above this the modem should attempt to reduce its power output to optimize its operation.
OBJECT-TYPE    
  INTEGER 0..310  

sheAdslLineConfProfileAturConfMinSnrMgn 1.3.6.1.4.1.231.7.1.2.1.6.1.1.4.1.21
Configured Minimum acceptable Signal/Noise Margin. If the noise margin falls below this level, the modem should attempt to increase its power output. If that is not possible the modem will attempt to re-initialize or shut down.
OBJECT-TYPE    
  INTEGER 0..310  

sheAdslLineConfProfileAturConfDownshiftSnrMgn 1.3.6.1.4.1.231.7.1.2.1.6.1.1.4.1.22
Configured Signal/Noise Margin for rate downshift. If the noise margin falls below this level, the modem should attempt to decrease its transmit rate. In the case that adaptAtRuntime mode is not present, the value will be 'don't care'.
OBJECT-TYPE    
  INTEGER 0..310  

sheAdslLineConfProfileAturConfUpshiftSnrMgn 1.3.6.1.4.1.231.7.1.2.1.6.1.1.4.1.23
Configured Signal/Noise Margin for rate upshift. If the noise margin rises above this level, the modem should attempt to increase its transmit rate. In the case that adaptAtRuntime mode is not present, the value will be 'don't care'.
OBJECT-TYPE    
  INTEGER 0..310  

sheAdslLineConfProfileAturConfMinUpshiftTime 1.3.6.1.4.1.231.7.1.2.1.6.1.1.4.1.24
Minimum time that the current margin is above UpshiftSnrMgn before an upshift occurs. In the case that adaptAtRuntime mode is not present, the value will be 'don't care'.
OBJECT-TYPE    
  INTEGER 0..16383  

sheAdslLineConfProfileAturConfMinDownshiftTime 1.3.6.1.4.1.231.7.1.2.1.6.1.1.4.1.25
Minimum time that the current margin is below DownshiftSnrMgn before a downshift occurs. In the case that adaptAtRuntime mode is not present, the value will be 'don't care'.
OBJECT-TYPE    
  INTEGER 0..16383  

sheAdslLineConfProfileAturChanConfFastMinTxRate 1.3.6.1.4.1.231.7.1.2.1.6.1.1.4.1.26
Configured Minimum Transmit rate for `Fast' channels, in kbps. See adslAturConfRateChanRatio for information regarding RADSL mode and ATUC transmit rate for ATUR receive rates. Only multiples of 32 will be configured.
OBJECT-TYPE    
  Unsigned32 32..3520  

sheAdslLineConfProfileAturChanConfInterleaveMinTxRate 1.3.6.1.4.1.231.7.1.2.1.6.1.1.4.1.27
Configured Minimum Transmit rate for `Interleave' channels, in kbps. See adslAturConfRateChanRatio for information regarding RADSL mode and ATUC transmit rate for ATUR receive rates. Only multiples of 32 will be configured.
OBJECT-TYPE    
  Unsigned32 32..3520  

sheAdslLineConfProfileAturChanConfFastMaxTxRate 1.3.6.1.4.1.231.7.1.2.1.6.1.1.4.1.28
Configured Maximum Transmit rate for `Fast' channels, in kbps. See adslAturConfRateChanRatio for information regarding RADSL mode and ATUC transmit rate for ATUR receive rates. Only multiples of 32 will be configured.
OBJECT-TYPE    
  Unsigned32 32..3520  

sheAdslLineConfProfileAturChanConfInterleaveMaxTxRate 1.3.6.1.4.1.231.7.1.2.1.6.1.1.4.1.29
Configured Maximum Transmit rate for `Interleave' channels, in kbps. See adslAturConfRateChanRatio for information regarding RADSL mode and see ATUC transmit rate for ATUR receive rates. Only multiples of 32 will be configured.
OBJECT-TYPE    
  Unsigned32 32..3520  

sheAdslLineConfProfileAturChanConfMaxInterleaveDelay 1.3.6.1.4.1.231.7.1.2.1.6.1.1.4.1.30
Configured maximum Interleave Delay for this channel. Interleave delay applies only to the interleave channel and defines the mapping (relative spacing) between subsequent input bytes at the interleaver input and their placement in the bit stream at the interleaver output. Larger numbers provide greater separation between consecutive input bytes in the output bit stream allowing for improved impulse noise immunity at the expense of payload latency.
OBJECT-TYPE    
  INTEGER 1..63  

sheAdslLineConfProfileTrellis 1.3.6.1.4.1.231.7.1.2.1.6.1.1.4.1.31
Indicates if Trelliscoding is enabled or not. If TrellisCoding is used is indicated in sheAdslLineTable and depence also on the Atur-Capabilities. The NE will not accept setting trellisOff. It is automatically controlled by firmware and will be switched off if ATU-R will not support this.
OBJECT-TYPE    
  SheAdslLineTrellisModeType  

sheAdslLineConfProfileAtucConfPwrMgmtL0Time 1.3.6.1.4.1.231.7.1.2.1.6.1.1.4.1.32
This parameter represents the minimum time (in seconds) between an exit from the L2 state and the next entry into the L2 state. It ranges from 0 to 255 seconds. Only valid for Adsl2 and Adsl2Plus.
OBJECT-TYPE    
  INTEGER 0..255  

sheAdslLineConfProfileAtucConfPwrMgmtL2Time 1.3.6.1.4.1.231.7.1.2.1.6.1.1.4.1.33
This parameter represents the minimum time (in seconds) between an Entry into the L2 state and the first Power Trim in the L2 state and between two consecutive Power Trims in the L2 State. It ranges from 0 to 255 seconds. Only valid for Adsl2 and Adsl2Plus.
OBJECT-TYPE    
  INTEGER 0..255  

sheAdslLineConfProfileAtucConfPwrMgmtL2ATPR 1.3.6.1.4.1.231.7.1.2.1.6.1.1.4.1.34
This parameter represents the maximum aggregate transmit power reduction (in dB) that can be performed through a single Power Trim in the L2 state. It ranges from 0 dB/10 to 310 dB/10. Only valid for Adsl2 and Adsl2Plus.
OBJECT-TYPE    
  INTEGER 0..310  

sheAdslLineConfProfileAtucConfPwrMgmtL2Rate 1.3.6.1.4.1.231.7.1.2.1.6.1.1.4.1.35
This parameter specifies the minimum net data rate during the low power state (L2). The data rate is coded in bit/s, and can range from 0x1F40 (8000) bps to 0xFA000 (1024000) bps. Only valid for Adsl2 and Adsl2Plus.
OBJECT-TYPE    
  INTEGER 8000..1024000  

sheAdslLineConfProfileAtucConfPwrMgmtMode 1.3.6.1.4.1.231.7.1.2.1.6.1.1.4.1.36
Which ADSL Power Management state is enabled. Only valid for Adsl2 and Adsl2Plus.
OBJECT-TYPE    
  SheAdslPwrMgmtModeType  

sheAdslLineConfProfileControl 1.3.6.1.4.1.231.7.1.2.1.6.1.1.5
OBJECT IDENTIFIER    

sheAdslLineConfProfileControlRequest 1.3.6.1.4.1.231.7.1.2.1.6.1.1.5.1
The different Controltypes for profile creation could be used to select predefined values for the supported standard. createAdslLineConfProfile (Adsl2PlusAnnexA) createAdslLineConfProfileAnnexA createAdslLineConfProfileAnnexB createAdslLineConfProfileAdsl2PlusAnnexB createAdslLineConfProfileAdsl2AnnexI createAdslLineConfProfileAdsl2AnnexJ createAdslLineConfProfileAdsl2PlusAnnexI createAdslLineConfProfileAdsl2PlusAnnexJ createAdslLineConfProfileAdsl2AnnexM createAdslLineConfProfileAdsl2PlusAnnexM sheAdslLineConfProfileControlName ... modifyAdslLineConfProfile sheAdslLineConfProfileControlIndex sheAdslLineConfProfileControlName ... deleteAdslLineConfProfile sheAdslLineConfProfileControlIndex sheAdslLineConfProfileControlName New with R2.8: createAdslLineConfProfileAdsl2PlusDynamic sheAdslLineConfProfileControlName
OBJECT-TYPE    
  SheAdslControlRequestType  

sheAdslLineConfProfileControlIndex 1.3.6.1.4.1.231.7.1.2.1.6.1.1.5.2
Index of the configured table-entry. Needed for modify or delete.
OBJECT-TYPE    
  Integer32  

sheAdslLineConfProfileControlStatus 1.3.6.1.4.1.231.7.1.2.1.6.1.1.5.3
The status of a user command.
OBJECT-TYPE    
  SheControlStatusType  

sheAdslLineConfProfileControlTimer 1.3.6.1.4.1.231.7.1.2.1.6.1.1.5.4
The maximum wait time for the manager for a long running user command.
OBJECT-TYPE    
  Gauge32  

sheAdslLineConfProfileControlReqResult 1.3.6.1.4.1.231.7.1.2.1.6.1.1.5.5
The result of the last user command.
OBJECT-TYPE    
  SheAdslControlRequestResultType  

sheAdslLineConfProfileControlTimeStamp 1.3.6.1.4.1.231.7.1.2.1.6.1.1.5.6
The time stamp of the last command (end of command).
OBJECT-TYPE    
  Unsigned32  

sheAdslLineConfProfileControlName 1.3.6.1.4.1.231.7.1.2.1.6.1.1.5.7
Descriptional name.
OBJECT-TYPE    
  SnmpAdminString  

sheAdslLineConfProfileControlAtucConfRateMode 1.3.6.1.4.1.231.7.1.2.1.6.1.1.5.8
Defines what form of transmit rate adaptation is configured on this modem. See ADSL Forum TR-005 [3] for more information.
OBJECT-TYPE    
  SheAdslLineConfRateModeType  

sheAdslLineConfProfileControlAtucConfRateChanRatio 1.3.6.1.4.1.231.7.1.2.1.6.1.1.5.9
Configured allocation ratio of excess transmit bandwidth between fast and interleaved channels. Only applies when two channel mode and rate adaptive DSL are supported. A ratio of 20% means, that 20 % of the available data rate (in access of the minimum rate summend over all bearer channels) will be assigned to the fast channel and 80% to the interleaved channel. Only valid if sheAdslLineConfExtnProfileLineType is set to dualLatency mode.
OBJECT-TYPE    
  INTEGER 0..100  

sheAdslLineConfProfileControlAtucConfTargetSnrMgn 1.3.6.1.4.1.231.7.1.2.1.6.1.1.5.10
Configured Target Signal/Noise Margin. This is the Noise Margin the modem must achieve with a BER of 10-7 or better to successfully complete initialization.
OBJECT-TYPE    
  INTEGER 0..310  

sheAdslLineConfProfileControlAtucConfMaxSnrMgn 1.3.6.1.4.1.231.7.1.2.1.6.1.1.5.11
Configured Maximum acceptable Signal/Noise Margin. If the Noise Margin is above this the modem should attempt to reduce its power output to optimize its operation.
OBJECT-TYPE    
  INTEGER 0..310  

sheAdslLineConfProfileControlAtucConfMinSnrMgn 1.3.6.1.4.1.231.7.1.2.1.6.1.1.5.12
Configured Minimum acceptable Signal/Noise Margin. If the noise margin falls below this level, the modem should attempt to increase its power output. If that is not possible the modem will attempt to re-initialize or shut down.
OBJECT-TYPE    
  INTEGER 0..310  

sheAdslLineConfProfileControlAtucConfDownshiftSnrMgn 1.3.6.1.4.1.231.7.1.2.1.6.1.1.5.13
Configured Signal/Noise Margin for rate downshift. If the noise margin falls below this level, the modem should attempt to decrease its transmit rate. In the case that RADSL mode is not present, the value will be `0'.
OBJECT-TYPE    
  INTEGER 0..310  

sheAdslLineConfProfileControlAtucConfUpshiftSnrMgn 1.3.6.1.4.1.231.7.1.2.1.6.1.1.5.14
Configured Signal/Noise Margin for rate upshift. If the noise margin rises above this level, the modem should attempt to increase its transmit rate. In the case that RADSL is not present, the value will be `0'.
OBJECT-TYPE    
  INTEGER 0..310  

sheAdslLineConfProfileControlAtucConfMinUpshiftTime 1.3.6.1.4.1.231.7.1.2.1.6.1.1.5.15
Minimum time that the current margin is above UpshiftSnrMgn before an upshift occurs. In the case that RADSL is not present, the value will be `0'.
OBJECT-TYPE    
  INTEGER 0..16383  

sheAdslLineConfProfileControlAtucConfMinDownshiftTime 1.3.6.1.4.1.231.7.1.2.1.6.1.1.5.16
Minimum time that the current margin is below DownshiftSnrMgn before a downshift occurs. In the case that RADSL mode is not present, the value will be `0'.
OBJECT-TYPE    
  INTEGER 0..16383  

sheAdslLineConfProfileControlAtucChanConfFastMinTxRate 1.3.6.1.4.1.231.7.1.2.1.6.1.1.5.17
Configured Minimum Transmit rate for `Fast' channels, in kbps. See adslAtucConfRateChanRatio for information regarding RADSL mode and ATUR transmit rate for ATUC receive rates. Only multiples of 32 will be configured.
OBJECT-TYPE    
  Unsigned32 0..32736  

sheAdslLineConfProfileControlAtucChanConfInterleaveMinTxRate 1.3.6.1.4.1.231.7.1.2.1.6.1.1.5.18
Configured Minimum Transmit rate for `Interleave' channels, in kbps. See adslAtucConfRateChanRatio for information regarding RADSL mode and see ATUR transmit rate for receive rates. Only multiples of 32 will be configured.
OBJECT-TYPE    
  Unsigned32 0..32736  

sheAdslLineConfProfileControlAtucChanConfFastMaxTxRate 1.3.6.1.4.1.231.7.1.2.1.6.1.1.5.19
Configured Maximum Transmit rate for `Fast' channels, in kbps. See adslAtucConfRateChanRatio for information regarding RADSL mode and see ATUR transmit rate for ATUC receive rates. Only multiples of 32 will be configured.
OBJECT-TYPE    
  Unsigned32 32..32736  

sheAdslLineConfProfileControlAtucChanConfInterleaveMaxTxRate 1.3.6.1.4.1.231.7.1.2.1.6.1.1.5.20
Configured Maximum Transmit rate for `Interleave' channels, in kbps. See adslAtucConfRateChanRatio for information regarding RADSL mode and ATUR transmit rate for ATUC receive rates. Only multiples of 32 will be configured.
OBJECT-TYPE    
  Unsigned32 32..32736  

sheAdslLineConfProfileControlAtucChanConfMaxInterleaveDelay 1.3.6.1.4.1.231.7.1.2.1.6.1.1.5.21
Configured maximum Interleave Delay for this channel. Interleave delay applies only to the interleave channel and defines the mapping (relative spacing) between subsequent input bytes at the interleaver input and their placement in the bit stream at the interleaver output. Larger numbers provide greater separation between consecutive input bytes in the output bit stream allowing for improved impulse noise immunity at the expense of payload latency.
OBJECT-TYPE    
  INTEGER 0..255  

sheAdslLineConfProfileControlAturConfRateMode 1.3.6.1.4.1.231.7.1.2.1.6.1.1.5.22
Defines what form of transmit rate adaptation is configured on this modem. See ADSL Forum TR-005 [3] for more information.
OBJECT-TYPE    
  SheAdslLineConfRateModeType  

sheAdslLineConfProfileControlAturConfRateChanRatio 1.3.6.1.4.1.231.7.1.2.1.6.1.1.5.23
Configured allocation ratio of excess transmit bandwidth between fast and interleaved channels. Only applies when two channel mode and rate adaptive DSL are supported. A ratio of 20% means, that 20 % of the available data rate (in access of the minimum rate summend over all bearer channels) will be assigned to the fast channel and 80% to the interleaved channel. Only valid if sheAdslLineConfExtnProfileLineType is set to dualLatency mode.
OBJECT-TYPE    
  INTEGER 0..100  

sheAdslLineConfProfileControlAturConfTargetSnrMgn 1.3.6.1.4.1.231.7.1.2.1.6.1.1.5.24
Configured Target Signal/Noise Margin. This is the Noise Margin the modem must achieve with a BER of 10-7 or better to successfully complete initialization.
OBJECT-TYPE    
  INTEGER 0..310  

sheAdslLineConfProfileControlAturConfMaxSnrMgn 1.3.6.1.4.1.231.7.1.2.1.6.1.1.5.25
Configured Maximum acceptable Signal/Noise Margin. If the Noise Margin is above this the modem should attempt to reduce its power output to optimize its operation.
OBJECT-TYPE    
  INTEGER 0..310  

sheAdslLineConfProfileControlAturConfMinSnrMgn 1.3.6.1.4.1.231.7.1.2.1.6.1.1.5.26
Configured Minimum acceptable Signal/Noise Margin. If the noise margin falls below this level, the modem should attempt to increase its power output. If that is not possible the modem will attempt to re-initialize or shut down.
OBJECT-TYPE    
  INTEGER 0..310  

sheAdslLineConfProfileControlAturConfDownshiftSnrMgn 1.3.6.1.4.1.231.7.1.2.1.6.1.1.5.27
Configured Signal/Noise Margin for rate downshift. If the noise margin falls below this level, the modem should attempt to decrease its transmit rate. In the case that RADSL mode is not present, the value will be `0'.
OBJECT-TYPE    
  INTEGER 0..310  

sheAdslLineConfProfileControlAturConfUpshiftSnrMgn 1.3.6.1.4.1.231.7.1.2.1.6.1.1.5.28
Configured Signal/Noise Margin for rate upshift. If the noise margin rises above this level, the modem should attempt to increase its transmit rate. In the case that RADSL is not present, the value will be `0'.
OBJECT-TYPE    
  INTEGER 0..310  

sheAdslLineConfProfileControlAturConfMinUpshiftTime 1.3.6.1.4.1.231.7.1.2.1.6.1.1.5.29
Minimum time that the current margin is above UpshiftSnrMgn before an upshift occurs. In the case that RADSL is not present, the value will be `0'.
OBJECT-TYPE    
  INTEGER 0..16383  

sheAdslLineConfProfileControlAturConfMinDownshiftTime 1.3.6.1.4.1.231.7.1.2.1.6.1.1.5.30
Minimum time that the current margin is below DownshiftSnrMgn before a downshift occurs. In the case that RADSL mode is not present, the value will be `0'.
OBJECT-TYPE    
  INTEGER 0..16383  

sheAdslLineConfProfileControlAturChanConfFastMinTxRate 1.3.6.1.4.1.231.7.1.2.1.6.1.1.5.31
Configured Minimum Transmit rate for `Fast' channels, in kbps. See adslAturConfRateChanRatio for information regarding RADSL mode and ATUC transmit rate for ATUR receive rates. Only multiples of 32 will be configured.
OBJECT-TYPE    
  Unsigned32 0..3520  

sheAdslLineConfProfileControlAturChanConfInterleaveMinTxRate 1.3.6.1.4.1.231.7.1.2.1.6.1.1.5.32
Configured Minimum Transmit rate for `Interleave' channels, in kbps. See adslAturConfRateChanRatio for information regarding RADSL mode and ATUC transmit rate for ATUR receive rates. Only multiples of 32 will be configured.
OBJECT-TYPE    
  Unsigned32 0..3520  

sheAdslLineConfProfileControlAturChanConfFastMaxTxRate 1.3.6.1.4.1.231.7.1.2.1.6.1.1.5.33
Configured Maximum Transmit rate for `Fast' channels, in kbps. See adslAturConfRateChanRatio for information regarding RADSL mode and ATUC transmit rate for ATUR receive rates. Only multiples of 32 will be configured.
OBJECT-TYPE    
  Unsigned32 32..3520  

sheAdslLineConfProfileControlAturChanConfInterleaveMaxTxRate 1.3.6.1.4.1.231.7.1.2.1.6.1.1.5.34
Configured Maximum Transmit rate for `Interleave' channels, in kbps. See adslAturConfRateChanRatio for information regarding RADSL mode and see ATUC transmit rate for ATUR receive rates. Only multiples of 32 will be configured.
OBJECT-TYPE    
  Unsigned32 32..3520  

sheAdslLineConfProfileControlAturChanConfMaxInterleaveDelay 1.3.6.1.4.1.231.7.1.2.1.6.1.1.5.35
Configured maximum Interleave Delay for this channel. Interleave delay applies only to the interleave channel and defines the mapping (relative spacing) between subsequent input bytes at the interleaver input and their placement in the bit stream at the interleaver output. Larger numbers provide greater separation between consecutive input bytes in the output bit stream allowing for improved impulse noise immunity at the expense of payload latency.
OBJECT-TYPE    
  INTEGER 0..255  

sheAdslLineConfProfileControlTrellis 1.3.6.1.4.1.231.7.1.2.1.6.1.1.5.36
Indicates if Trelliscoding is enabled or not. If TrellisCoding is used is indicated in sheAdslLineTable and depence also on the Atur-Capabilities. Do not touch!
OBJECT-TYPE    
  SheAdslLineTrellisModeType  

sheAdslLineConfProfileControlAtucConfPwrMgmtL0Time 1.3.6.1.4.1.231.7.1.2.1.6.1.1.5.37
This parameter represents the minimum time (in seconds) between an exit from the L2 state and the next entry into the L2 state. It ranges from 0 to 255 seconds. Only valid for Adsl2 and Adsl2Plus.
OBJECT-TYPE    
  INTEGER 0..255  

sheAdslLineConfProfileControlAtucConfPwrMgmtL2Time 1.3.6.1.4.1.231.7.1.2.1.6.1.1.5.38
This parameter represents the minimum time (in seconds) between an Entry into the L2 state and the first Power Trim in the L2 state and between two consecutive Power Trims in the L2 State. It ranges from 0 to 255 seconds. Only valid for Adsl2 and Adsl2Plus.
OBJECT-TYPE    
  INTEGER 0..255  

sheAdslLineConfProfileControlAtucConfPwrMgmtL2ATPR 1.3.6.1.4.1.231.7.1.2.1.6.1.1.5.39
This parameter represents the maximum aggregate transmit power reduction (in dB) that can be performed through a single Power Trim in the L2 state. It ranges from 0 dB/10 to 310 dB/10. Only valid for Adsl2 and Adsl2Plus.
OBJECT-TYPE    
  INTEGER 0..310  

sheAdslLineConfProfileControlAtucConfPwrMgmtL2Rate 1.3.6.1.4.1.231.7.1.2.1.6.1.1.5.40
This parameter specifies the minimum net data rate during the low power state (L2). The data rate is coded in bit/s, and can range from 0x1F40 (8000) bps to 0xFA000 (1024000) bps. Only valid for Adsl2 and Adsl2Plus.
OBJECT-TYPE    
  INTEGER 8000..1024000  

sheAdslLineConfProfileControlAtucConfPwrMgmtMode 1.3.6.1.4.1.231.7.1.2.1.6.1.1.5.41
Which ADSL Power Management state is enabled. Only valid for Adsl2 and Adsl2Plus.
OBJECT-TYPE    
  SheAdslPwrMgmtModeType  

sheAdslLineConfExtnProfileTable 1.3.6.1.4.1.231.7.1.2.1.6.1.1.6
This table contains information on the ADSL line configuration. One entry in this table reflects a profile defined by a manager which can be used to configure the ADSL line.
OBJECT-TYPE    
  SEQUENCE OF  
    SheAdslLineConfExtnProfileEntry

sheAdslLineConfExtnProfileEntry 1.3.6.1.4.1.231.7.1.2.1.6.1.1.6.1
Each entry consists of a list of parameters that represents the configuration of an ADSL modem. The index is used from the sheAdslLineConfProfileTable.
OBJECT-TYPE    
  SheAdslLineConfExtnProfileEntry  

sheAdslLineConfExtnProfileParametricTestInputFile 1.3.6.1.4.1.231.7.1.2.1.6.1.1.6.1.1
Indicates Name of the Input file from which to take the Mask Array Size, lower and upper mask Array. Null string means no file is specified. Functionality is not supported!
OBJECT-TYPE    
  DisplayString  

sheAdslLineConfExtnProfileRsIntCorrectionUp 1.3.6.1.4.1.231.7.1.2.1.6.1.1.6.1.2
Sets the correction time for the upstream-interleaved buffer. RS can also be disabled. The Default Value for ADSL+ is 3. value125us(3), value250us(4), value500us(5), value1ms(6), value2ms(7), value4ms(8), disable(15)
OBJECT-TYPE    
  SheAdslLineConfRsIntCorrectionType  

sheAdslLineConfExtnProfileLineType 1.3.6.1.4.1.231.7.1.2.1.6.1.1.6.1.3
This parameter provisions the DSL physical entity at start-up by defining whether and how the line will be channelized, i.e. which channel type(s) are supported. Defined values are: fastOnly(2) -- only fast channel exists (singleLatency) interleavedOnly(3) -- only interleaved channel exists (singleLatency, default) fastAndInterleaved(5) -- both fast and interleaved channels (dualLatency) exist In case of dualLatency (mode 5), the parameter's sheAdslLineConfProfileAtucConfRateChanRatio and sheAdslLineConfProfileAturConfRateChanRatio configures the bandwith distribution. IMPORTANT NOTE: The configuration of dualLatency mode is only available for NE releases up R2.5!! The modification is only possible for profiles, which are NOT IN USE!
OBJECT-TYPE    
  SheAdslConfLineType  

sheAdslLineConfExtnProfileTxEndBin 1.3.6.1.4.1.231.7.1.2.1.6.1.1.6.1.4
Highest bin number allowed for Tx signal. The Range & default for ADSL+ is 0x06 - 0x1ff respectively. NE will not accept any changes and use always default value! Ne will select the correct values depending on the configuration of the following values: - AnnexType - DmtConfMode - AdvertisedCapability New with R2.8: If the used annexType was set to 'dynamic', no values of Tx/Rx bins could be set here, because this will be done by the IU depending on the used HW and choosen standard. The profile configuration will be set to value 65535 (0xffff) which means 'autoSelect'.
OBJECT-TYPE    
  INTEGER 6..511 | 65535  

sheAdslLineConfExtnProfileTxStartBin 1.3.6.1.4.1.231.7.1.2.1.6.1.1.6.1.5
Lowest bin number allowed for Tx signal.The Range for ADSL+ is 0x06 - 0x1ff. The Default for Annex B is 58 respectively. For AnnexA it is 32. NE will not accept any changes and use always default value! Ne will select the correct values depending on the configuration of the following values: - AnnexType - DmtConfMode - AdvertisedCapability New with R2.8: If the used annexType was set to 'dynamic', no values of Tx/Rx bins could be set here, because this will be done by the IU depending on the used HW and choosen standard. The profile configuration will be set to value 65535 (0xffff) which means 'autoSelect'.
OBJECT-TYPE    
  INTEGER 6..511 | 65535  

sheAdslLineConfExtnProfileMaxBitsPerBin 1.3.6.1.4.1.231.7.1.2.1.6.1.1.6.1.6
Maximum Rx number of bits per bin. NE will not accept any changes and use always default value!
OBJECT-TYPE    
  INTEGER 0..15  

sheAdslLineConfExtnProfileRxStartBin 1.3.6.1.4.1.231.7.1.2.1.6.1.1.6.1.7
Lowest bin number allowed for Rx signal. Default value for AnnexA is 6 and 32 for AnnexB. NE will not accept any changes and use always default value! Ne will select the correct values depending on the configuration of the following values: - AnnexType - DmtConfMode - AdvertisedCapability New with R2.8: If the used annexType was set to 'dynamic', no values of Tx/Rx bins could be set here, because this will be done by the IU depending on the used HW and choosen standard. The profile configuration will be set to value 65535 (0xffff) which means 'autoSelect'.
OBJECT-TYPE    
  INTEGER 1..57 | 65535  

sheAdslLineConfExtnProfileRxEndBin 1.3.6.1.4.1.231.7.1.2.1.6.1.1.6.1.8
Highest bin number allowed for Rx signal. Default Value for AnnexA is 31 and 57 for AnnexB. NE will not accept any changes and use always default value! Ne will select the correct values depending on the configuration of the following values: - AnnexType - DmtConfMode - AdvertisedCapability New with R2.8: If the used annexType was set to 'dynamic', no values of Tx/Rx bins could be set here, because this will be done by the IU depending on the used HW and choosen standard. The profile configuration will be set to value 65535 (0xffff) which means 'autoSelect'.
OBJECT-TYPE    
  INTEGER 6..64 | 65535  

sheAdslLineConfExtnProfileRxBinAdjust 1.3.6.1.4.1.231.7.1.2.1.6.1.1.6.1.9
Employs Rx Start/End bin settings. NE will not accept any changes and use always default value!
OBJECT-TYPE    
  SheAdslLineConfExtnProfileRxBinAdjustType  

sheAdslLineConfExtnProfileTriggerMode 1.3.6.1.4.1.231.7.1.2.1.6.1.1.6.1.10
Indicates the Type of event that triggers fast retrain. disable(0), locCrc(1), rmtCrc(2), snrInc(4), snrDec(8) NE will not accept any changes and use always default value!
OBJECT-TYPE    
  SheAdslLineConfTriggerModeType  

sheAdslLineConfExtnProfileAdi2x 1.3.6.1.4.1.231.7.1.2.1.6.1.1.6.1.11
For non standard compliant ADI CPE. NE will not accept any changes and use always default value!
OBJECT-TYPE    
  SheAdslLineConfExtnProfileAdi2xType  

sheAdslLineConfExtnProfileStandard 1.3.6.1.4.1.231.7.1.2.1.6.1.1.6.1.12
Preferred standard compliance. Outcome is dependent upon standard support of the remote unit.GlobespanVirata High Speed ADSL DMT (ADSL+) applications only. t1413(0), gLite(1), gDmt(2), multiMode(4), adsl2(26), adsl2_plus(27), readsl2(28), adsl2_auto(29), adsl2_plus_auto(30), adsl2adsl2PlusOnly(31) New with R2.8: If the used annexType was set to 'dynamic', the standardTypes 't1413', 'gLite', 'gDmt' and 'readsl2' could NOT be used. 'adsl2_plus_auto' should be the prefered use in that case!
OBJECT-TYPE    
  SheAdslLineConfStandardType  

sheAdslLineConfExtnProfileInitiate 1.3.6.1.4.1.231.7.1.2.1.6.1.1.6.1.13
Specifies which end initiates startup. It is also used to send a C-tone to the remote unit. waitPn(0), ctone(1), initiatePn(128) NE will not accept any changes and use always default value!
OBJECT-TYPE    
  SheAdslLineConfInitiateType  

sheAdslLineConfExtnProfileTxPowerAttenuation 1.3.6.1.4.1.231.7.1.2.1.6.1.1.6.1.14
Specifies value of Tx power attenuation. value0(0)...value21(21)
OBJECT-TYPE    
  SheAdslLineConfAttenuationType  

sheAdslLineConfExtnProfileCodingGain 1.3.6.1.4.1.231.7.1.2.1.6.1.1.6.1.15
Sets the coding gain in dB increments. gain0(0), gain1(4096), gain2(8192), gain3(12288), gain4(16384), gain5(20480), gain6(24576), gain7(28672), auto(65280) NE will not accept any changes and use always default value!
OBJECT-TYPE    
  SheAdslLineConfGainType  

sheAdslLineConfExtnProfileRsFastOvrhdDown 1.3.6.1.4.1.231.7.1.2.1.6.1.1.6.1.16
Sets the percentage overhead for the downstream-fast buffer. ovrHd50(1), ovrHd25(2), ovrHd12(3), ovrHd6(4), ovrHd3(5), ovrHd1(7), disable(15) NE will not accept any changes and use always default value!
OBJECT-TYPE    
  SheAdslLineConfRsFastOvrhdType  

sheAdslLineConfExtnProfileIntCorrectionDown 1.3.6.1.4.1.231.7.1.2.1.6.1.1.6.1.17
This parameter sets the correction time for the downstream interleaved buffer. RS can also be disabled. value125us(3), value250us(4), value500us(5), value1ms(6), value2ms(7), value4ms(8), disable(15)
OBJECT-TYPE    
  SheAdslLineConfRsIntCorrectionType  

sheAdslLineConfExtnProfileRsFastOvrhdUp 1.3.6.1.4.1.231.7.1.2.1.6.1.1.6.1.18
Sets the percentage overhead for the upstream-fast buffer. ovrHd50(1), ovrHd25(2), ovrHd12(3), ovrHd6(4), ovrHd3(5), ovrHd1(7), disable(15) NE will not accept any changes and use always default value!
OBJECT-TYPE    
  SheAdslLineConfRsFastOvrhdType  

sheAdslLineConfExtnProfileDrStby 1.3.6.1.4.1.231.7.1.2.1.6.1.1.6.1.19
Provides the ability to disable power to the line driver. disable(0), enable(1) NE will not accept any changes and use always default value!
OBJECT-TYPE    
  SheAdslLineConfEnableType  

sheAdslLineConfExtnProfileExpandedExchange 1.3.6.1.4.1.231.7.1.2.1.6.1.1.6.1.20
This object is used to Enable/Disable EES. disable(0), enable(1) NE will not accept any changes and use always default value!
OBJECT-TYPE    
  SheAdslLineConfExpandedExchangeType  

sheAdslLineConfExtnProfileEscapeFastRetrainEnable 1.3.6.1.4.1.231.7.1.2.1.6.1.1.6.1.21
This object is used to Enable/ Disable escape to the fast retrain capability. disable(0), enable(1) NE will not accept any changes and use always default value!
OBJECT-TYPE    
  SheAdslLineConfEnableType  

sheAdslLineConfExtnProfileFastRetrainEnable 1.3.6.1.4.1.231.7.1.2.1.6.1.1.6.1.22
This object is used to Enable/ Disable the fast retrain capability. disable(32768), enable(0) NE will not accept any changes and use always default value!
OBJECT-TYPE    
  SheAdslLineConfEnableSpecial3Type  

sheAdslLineConfExtnProfileBitSwap 1.3.6.1.4.1.231.7.1.2.1.6.1.1.6.1.23
This object is used to Enable/Disable bit swapping. enable(32768), disable(0)
OBJECT-TYPE    
  SheAdslLineConfEnableSpecial2Type  

sheAdslLineConfExtnProfileNtr 1.3.6.1.4.1.231.7.1.2.1.6.1.1.6.1.24
This object is used to Enable/ Disable NTR on a per chip basis.
OBJECT-TYPE    
  SheAdslLineConfNtrType  

sheAdslLineConfExtnProfileAnnexType 1.3.6.1.4.1.231.7.1.2.1.6.1.1.6.1.25
This parameter is set as per annex compliance of the code release. GlobespanVirata High Speed ADSL DMT (ADSL+) applications only. annexA(0), annexB(1), highSpeed(2), annexAdsl2(5), annexI(10), annexJ(11), annexM(12) New with R2.8: dynamic(50) If the used annexType was set to 'dynamic', such a profile could be assigned to any type of supported ADSL IU. The IU will select the supported annex himself, depending on HW restrictions and line parameters. This selection made additional restrictions to the following parameters: - tx/rx start and end bin usage - profile Standard - profile AdvertisedCapabilities - profileLineDmtConfMode
OBJECT-TYPE    
  SheAdslLineConfAnnexType  

sheAdslLineConfExtnProfileAlctlUsVer 1.3.6.1.4.1.231.7.1.2.1.6.1.1.6.1.26
This object is used for T1.413 demo purposes only. NE will not accept any changes and use always default value!
OBJECT-TYPE    
  SheAdslLineConfExtnProfileAlctlUsVerType  

sheAdslLineConfExtnProfileUseCustomBin 1.3.6.1.4.1.231.7.1.2.1.6.1.1.6.1.27
This object is used to Enable/ Disable user selection of bin-usage defined in sheAdslLineConfExtnProfileDnBinUsage. disable(0), enable(32768)
OBJECT-TYPE    
  SheAdslLineConfEnableSpecial2Type  

sheAdslLineConfExtnProfileDnBinUsage 1.3.6.1.4.1.231.7.1.2.1.6.1.1.6.1.28
The parameter where a 1 in bit position indicates usage of corresponding bin, whereas a 0 disables usage of corresponding bin.
OBJECT-TYPE    
  OCTET STRING Size(0..64)  

sheAdslLineConfExtnProfileMaxDCo 1.3.6.1.4.1.231.7.1.2.1.6.1.1.6.1.29
This object is used to indicate Maximum interleaving depth supported by the customer's hardware. value64(0), value128(4096), value256(8192)
OBJECT-TYPE    
  SheAdslLineConfIntDephtType  

sheAdslLineConfExtnProfileFullRetrain 1.3.6.1.4.1.231.7.1.2.1.6.1.1.6.1.30
This object is used to Indicate enable/disable of auto retrain capability. enable(0), disable(32768) NE will not accept any changes and use always default value!
OBJECT-TYPE    
  SheAdslLineConfEnableSpecial3Type  

sheAdslLineConfExtnProfileAdvertisedCapabilities 1.3.6.1.4.1.231.7.1.2.1.6.1.1.6.1.31
Controls if the CO will attempt to startup using alternate standards if the CPE does not support ADSL+. New with R2.8: If the used annexType was set to 'dynamic', this parameter should be set to 'disabled' or 'adslPlus'. All other values will not work with the intended set of dynamic annexType selection by IU.
OBJECT-TYPE    
  SheAdslLineConfAdvertisedCapabilitiesType  

sheAdslLineConfExtnProfilePsdMaskType 1.3.6.1.4.1.231.7.1.2.1.6.1.1.6.1.32
Selects the PSD mask option to be used.
OBJECT-TYPE    
  SheAdslLineConfPsdMaskType  

sheAdslLineConfExtnProfileLineDmtConfMode 1.3.6.1.4.1.231.7.1.2.1.6.1.1.6.1.33
Selects if there is overlap or no overlap of bins. Overlapping is only supported by non ISDN profiles and will change the setting for TxStartBin accordingly!!. New with R2.8: If the used annexType was set to 'dynamic', this parameter should be set to 'fdmMode' only. Other values will not work with the intended set of dynamic annexType selection by IU.
OBJECT-TYPE    
  SheAdslLineConfLineDmtConfModeType  

sheAdslLineConfExtnProfileEraseProfiles 1.3.6.1.4.1.231.7.1.2.1.6.1.1.6.1.34
Enables/Disables the ability to erase all fast retrain profiles at startup. disable(0), enable(32768)
OBJECT-TYPE    
  SheAdslLineConfEnableSpecial2Type  

sheAdslLineConfExtnProfileRsMemory 1.3.6.1.4.1.231.7.1.2.1.6.1.1.6.1.35
Indicates whether customer's Hardware should use external RS RAM. Could not be configured and depends only on the used card type.
OBJECT-TYPE    
  SheAdslLineConfRsMemoryType  

sheAdslLineConfExtnProfileParamHybridLossTestStart 1.3.6.1.4.1.231.7.1.2.1.6.1.1.6.1.36
Indicates Start bin for range of bins to be measured.
OBJECT-TYPE    
  INTEGER 0..511  

sheAdslLineConfExtnProfileParamHybridLossTestEnd 1.3.6.1.4.1.231.7.1.2.1.6.1.1.6.1.37
Indicates End bin for range of bins to be measured.
OBJECT-TYPE    
  INTEGER 0..511  

sheAdslLineConfExtnProfileConfMinInp 1.3.6.1.4.1.231.7.1.2.1.6.1.1.6.1.38
New ADSL2+ parameter. The user configures the duration of impulse noise the system should withstand. This parameter configures the value for downstream direction.
OBJECT-TYPE    
  SheAdslConfMinInpType  

sheAdslLineConfExtnProfileRfiBandMask 1.3.6.1.4.1.231.7.1.2.1.6.1.1.6.1.39
BitMask for sheAdslRfiBandIndex. Configured RFI bands are used for this profile.
OBJECT-TYPE    
  OCTET STRING Size(4)  

sheAdslLineConfExtnProfileUpstreamPsdMaskSelection 1.3.6.1.4.1.231.7.1.2.1.6.1.1.6.1.40
Selects the PSD mask option to be used. This parameter is used only for annexes J and M of ITU-T Recs. G.992-3 and G.992.5 Other profiles will ignore the configured value and use per default the value noSelection(0).
OBJECT-TYPE    
  SheAdslLineConfUpstreamPSDMaskSelectionType  

sheAdslLineConfExtnProfileMaxNomPsdDs 1.3.6.1.4.1.231.7.1.2.1.6.1.1.6.1.41
The maximum nominal transmit PSD in the downstream direction during initialization and Showtime. It ranges from -600 to -300 units of 0.1 dBm/Hz. (physical values are -60 to -30 dBm/Hz).
OBJECT-TYPE    
  INTEGER -600..-300  

sheAdslLineConfExtnProfileMaxNomAtpDs 1.3.6.1.4.1.231.7.1.2.1.6.1.1.6.1.42
The maximum nominal aggregate transmit power in the downstream direction during initialization and Showtime. It ranges from 0 to 255 units of 0.1 dBm (physical values are 0 to 25.5 dBm).
OBJECT-TYPE    
  Gauge32 0..255  

sheAdslLineConfExtnProfilePsdMaskDs 1.3.6.1.4.1.231.7.1.2.1.6.1.1.6.1.43
The downstream PSD mask applicable at the U-C2 reference point. This parameter is used only for G.992.5 and it may impose PSD restrictions (breakpoints) in addition to the Limit PSD mask defined in G.992.5. This is a string of 32 pairs of values in the following structure: Octets 0+1 - Index of 1st sub-carrier used in the context of a first breakpoint. Octet 2 - The PSD reduction for the sub-carrier indicated in octets 0 and 1. Octets 3-5 - Same, for a 2nd breakpoint. Octets 6-8 - Same, for a 3rd breakpoint. This architecture continues until octets 94-95, which are associated with a 32nd breakpoint. Each subcarrier index is an unsigned number in the range 1 and NSCds. Each PSD reduction value is in the range 0 (0dBm/Hz) to 255 (-127.5dBm/Hz) with steps of 0.5dBm/Hz. Valid values are in the range 0 to 190 (0 to -95dBm/Hz). But the range of start-bin and end-bin is in range 0 to 195 (0 to -97.5dBm/Hz). Two break points (6 byte) are reserved for start sub-carrier index and end sub-carrier index. So the range of size is 6 up to 96. When the number of breakpoints is less than 32, all remaining octets are set to the value 0. Note that the content of this object should be correlated with the sub-carriers mask and with the RFI setup.
OBJECT-TYPE    
  OCTET STRING Size(6..96)  

sheAdslLineConfExtnProfilePSDMASKdsEnable 1.3.6.1.4.1.231.7.1.2.1.6.1.1.6.1.44
User custom PSD mask-related parameter used by the ATU-C to use user custom PSD mask. (Not available for ADSL but ADSL2 and ADSL2plus ).
OBJECT-TYPE    
  SheAdslLineConfEnableType  

sheAdslLineConfExtnProfileConfMinInpUs 1.3.6.1.4.1.231.7.1.2.1.6.1.1.6.1.45
New ADSL2+ parameter. The user configures the duration of impulse noise the system should withstand. This parameter configures the value for upstream direction.
OBJECT-TYPE    
  SheAdslConfMinInpType  

sheAdslLineConfExtnProfileControl 1.3.6.1.4.1.231.7.1.2.1.6.1.1.7
OBJECT IDENTIFIER    

sheAdslLineConfExtnProfileControlRequest 1.3.6.1.4.1.231.7.1.2.1.6.1.1.7.1
modifyAdslLineConfExtnProfile sheAdslLineConfExtnProfileControlIndex sheAdslLineConfExtnProfileControlName ...
OBJECT-TYPE    
  SheAdslControlRequestType  

sheAdslLineConfExtnProfileControlIndex 1.3.6.1.4.1.231.7.1.2.1.6.1.1.7.2
Index of the table entry to be configured. Needed for modify.
OBJECT-TYPE    
  Integer32  

sheAdslLineConfExtnProfileControlStatus 1.3.6.1.4.1.231.7.1.2.1.6.1.1.7.3
The status of a user command.
OBJECT-TYPE    
  SheControlStatusType  

sheAdslLineConfExtnProfileControlTimer 1.3.6.1.4.1.231.7.1.2.1.6.1.1.7.4
The maximum wait time for the manager for a long running user command.
OBJECT-TYPE    
  Gauge32  

sheAdslLineConfExtnProfileControlReqResult 1.3.6.1.4.1.231.7.1.2.1.6.1.1.7.5
The result of the last user command.
OBJECT-TYPE    
  SheAdslControlRequestResultType  

sheAdslLineConfExtnProfileControlTimeStamp 1.3.6.1.4.1.231.7.1.2.1.6.1.1.7.6
The time stamp of the last command (end of command).
OBJECT-TYPE    
  Unsigned32  

sheAdslLineConfExtnProfileControlName 1.3.6.1.4.1.231.7.1.2.1.6.1.1.7.7
Descriptional name. The name used during configuration of this profile is equal to the name of the sheAdslLineConfProfile with the identical index.
OBJECT-TYPE    
  SnmpAdminString  

sheAdslLineConfExtnProfileControlParametricTestInputFile 1.3.6.1.4.1.231.7.1.2.1.6.1.1.7.8
Indicates Name of the Input file from which to take the Mask Array Size, lower and upper mask Array. Null string means no file is specified.
OBJECT-TYPE    
  DisplayString  

sheAdslLineConfExtnProfileControlRsIntCorrectionUp 1.3.6.1.4.1.231.7.1.2.1.6.1.1.7.9
Sets the correction time for the upstream-interleaved buffer. RS can also be disabled. The Default Value for ADSL+ is 3.
OBJECT-TYPE    
  SheAdslLineConfRsIntCorrectionType  

sheAdslLineConfExtnProfileControlLineType 1.3.6.1.4.1.231.7.1.2.1.6.1.1.7.10
This parameter provisions the DSL physical entity at start-up by defining whether and how the line will be channelized, i.e. which channel type(s) are supported. Defined values are: fastOnly(2) -- only fast channel exists (singleLatency) interleavedOnly(3) -- only interleaved channel exists (singleLatency, default) fastAndInterleaved(5) -- both fast and interleaved channels (dualLatency) exist In case of dualLatency (mode 5), the parameter's sheAdslLineConfProfileAtucConfRateChanRatio and sheAdslLineConfProfileAturConfRateChanRatio configures the bandwith distribution. IMPORTANT NOTE: The configuration of dualLatency mode is only available for NE releases up R2.5!! The modification is only possible for profiles, which are NOT IN USE!
OBJECT-TYPE    
  SheAdslConfLineType  

sheAdslLineConfExtnProfileControlTxEndBin 1.3.6.1.4.1.231.7.1.2.1.6.1.1.7.11
Highest bin number allowed for Tx signal. The Range & default for ADSL+ is 0x06 - 0x1ff respectively. NE will not accept any changes and use always default value! Ne will select the correct values depending on the configuration of the following values: - AnnexType - DmtConfMode - AdvertisedCapability
OBJECT-TYPE    
  INTEGER 6..511  

sheAdslLineConfExtnProfileControlTxStartBin 1.3.6.1.4.1.231.7.1.2.1.6.1.1.7.12
Lowest bin number allowed for Tx signal.The Range for ADSL+ is 0x06 - 0x1ff. NE will not accept any changes and use always default value! Ne will select the correct values depending on the configuration of the following values: - AnnexType - DmtConfMode - AdvertisedCapability
OBJECT-TYPE    
  INTEGER 6..511  

sheAdslLineConfExtnProfileControlMaxBitsPerBin 1.3.6.1.4.1.231.7.1.2.1.6.1.1.7.13
Maximum Rx number of bits per bin. NE will not accept any changes and use always default value!
OBJECT-TYPE    
  INTEGER 0..15  

sheAdslLineConfExtnProfileControlRxStartBin 1.3.6.1.4.1.231.7.1.2.1.6.1.1.7.14
Lowest bin number allowed for Rx signal. NE will not accept any changes and use always default value! Ne will select the correct values depending on the configuration of the following values: - AnnexType - DmtConfMode - AdvertisedCapability
OBJECT-TYPE    
  INTEGER 1..57  

sheAdslLineConfExtnProfileControlRxEndBin 1.3.6.1.4.1.231.7.1.2.1.6.1.1.7.15
Highest bin number allowed for Rx signal. NE will not accept any changes and use always default value! Ne will select the correct values depending on the configuration of the following values: - AnnexType - DmtConfMode - AdvertisedCapability
OBJECT-TYPE    
  INTEGER 6..64  

sheAdslLineConfExtnProfileControlRxBinAdjust 1.3.6.1.4.1.231.7.1.2.1.6.1.1.7.16
Employs Rx Start/End bin settings. NE will not accept any changes and use always default value!
OBJECT-TYPE    
  SheAdslLineConfExtnProfileRxBinAdjustType  

sheAdslLineConfExtnProfileControlTriggerMode 1.3.6.1.4.1.231.7.1.2.1.6.1.1.7.17
Indicates the Type of event that triggers fast retrain. NE will not accept any changes and use always default value!
OBJECT-TYPE    
  SheAdslLineConfTriggerModeType  

sheAdslLineConfExtnProfileControlAdi2x 1.3.6.1.4.1.231.7.1.2.1.6.1.1.7.18
For non standard compliant ADI CPE. NE will not accept any changes and use always default value!
OBJECT-TYPE    
  SheAdslLineConfExtnProfileAdi2xType  

sheAdslLineConfExtnProfileControlStandard 1.3.6.1.4.1.231.7.1.2.1.6.1.1.7.19
Preferred standard compliance. Outcome is dependent upon standard support of the remote unit.GlobespanVirata High Speed ADSL DMT (ADSL+) applications only. New with R2.8: If the used annexType was set to 'dynamic', the standardTypes 't1413', 'gLite', 'gDmt' and 'readsl2' could NOT be used. 'adsl2_plus_auto' should be the prefered use in that case!
OBJECT-TYPE    
  SheAdslLineConfStandardType  

sheAdslLineConfExtnProfileControlInitiate 1.3.6.1.4.1.231.7.1.2.1.6.1.1.7.20
Specifies which end initiates startup. It is also used to send a C-tone to the remote unit. NE will not accept any changes and use always default value!
OBJECT-TYPE    
  SheAdslLineConfInitiateType  

sheAdslLineConfExtnProfileControlTxPowerAttenuation 1.3.6.1.4.1.231.7.1.2.1.6.1.1.7.21
Specifies value of Tx power attenuation.
OBJECT-TYPE    
  SheAdslLineConfAttenuationType  

sheAdslLineConfExtnProfileControlCodingGain 1.3.6.1.4.1.231.7.1.2.1.6.1.1.7.22
Sets the coding gain in dB increments. NE will not accept any changes and use always default value!
OBJECT-TYPE    
  SheAdslLineConfGainType  

sheAdslLineConfExtnProfileControlRsFastOvrhdDown 1.3.6.1.4.1.231.7.1.2.1.6.1.1.7.23
Sets the percentage overhead for the downstream-fast buffer. NE will not accept any changes and use always default value!
OBJECT-TYPE    
  SheAdslLineConfRsFastOvrhdType  

sheAdslLineConfExtnProfileControlIntCorrectionDown 1.3.6.1.4.1.231.7.1.2.1.6.1.1.7.24
This parameter sets the correction time for the downstream interleaved buffer.RS can also be disabled.
OBJECT-TYPE    
  SheAdslLineConfRsIntCorrectionType  

sheAdslLineConfExtnProfileControlRsFastOvrhdUp 1.3.6.1.4.1.231.7.1.2.1.6.1.1.7.25
Sets the percentage overhead for the upstream-fast buffer. NE will not accept any changes and use always default value!
OBJECT-TYPE    
  SheAdslLineConfRsFastOvrhdType  

sheAdslLineConfExtnProfileControlDrStby 1.3.6.1.4.1.231.7.1.2.1.6.1.1.7.26
Provides the ability to disable power to the line driver. NE will not accept any changes and use always default value!
OBJECT-TYPE    
  SheAdslLineConfEnableType  

sheAdslLineConfExtnProfileControlExpandedExchange 1.3.6.1.4.1.231.7.1.2.1.6.1.1.7.27
This object is used to Enable/Disable EES. NE will not accept any changes and use always default value!
OBJECT-TYPE    
  SheAdslLineConfExpandedExchangeType  

sheAdslLineConfExtnProfileControlEscapeFastRetrainEnable 1.3.6.1.4.1.231.7.1.2.1.6.1.1.7.28
This object is used to Enable/ Disable escape to the fast retrain capability. NE will not accept any changes and use always default value!
OBJECT-TYPE    
  SheAdslLineConfEnableType  

sheAdslLineConfExtnProfileControlFastRetrainEnable 1.3.6.1.4.1.231.7.1.2.1.6.1.1.7.29
This object is used to Enable/ Disable the fast retrain capability. NE will not accept any changes and use always default value!
OBJECT-TYPE    
  SheAdslLineConfEnableSpecial3Type  

sheAdslLineConfExtnProfileControlBitSwap 1.3.6.1.4.1.231.7.1.2.1.6.1.1.7.30
This object is used to Enable/Disable bit swapping.
OBJECT-TYPE    
  SheAdslLineConfEnableSpecial2Type  

sheAdslLineConfExtnProfileControlNtr 1.3.6.1.4.1.231.7.1.2.1.6.1.1.7.31
This object is used to Enable/ Disable NTR on a per chip basis.
OBJECT-TYPE    
  SheAdslLineConfNtrType  

sheAdslLineConfExtnProfileControlAnnexType 1.3.6.1.4.1.231.7.1.2.1.6.1.1.7.32
This parameter is set as per annex compliance of the code release. GlobespanVirata High Speed ADSL DMT (ADSL+) applications only. New with R2.8: dynamic(50) If the used annexType was set to 'dynamic', such a profile could be assigned to any type of supported ADSL IU. The IU will select the supported annex himself, depending on HW restrictions and line parameters. This selection made additional restrictions to the following parameters: - tx/rx start and end bin usage - profile Standard - profile AdvertisedCapabilities - profileLineDmtConfMode
OBJECT-TYPE    
  SheAdslLineConfAnnexType  

sheAdslLineConfExtnProfileControlAlctlUsVer 1.3.6.1.4.1.231.7.1.2.1.6.1.1.7.33
This object is used for T1.413 demo purposes only. NE will not accept any changes and use always default value!
OBJECT-TYPE    
  SheAdslLineConfExtnProfileAlctlUsVerType  

sheAdslLineConfExtnProfileControlUseCustomBin 1.3.6.1.4.1.231.7.1.2.1.6.1.1.7.34
This object is used to Enable/ Disable user selection on which of the 256 bins will be enabled for downstream transmission.
OBJECT-TYPE    
  SheAdslLineConfEnableSpecial2Type  

sheAdslLineConfExtnProfileControlDnBinUsage 1.3.6.1.4.1.231.7.1.2.1.6.1.1.7.35
The parameter where a 1 in bit position indicates usage of corresponding bin,whereas a 0 disables usage of corresponding bin.
OBJECT-TYPE    
  OCTET STRING Size(0..64)  

sheAdslLineConfExtnProfileControlMaxDCo 1.3.6.1.4.1.231.7.1.2.1.6.1.1.7.36
This object is used to indicate Maximum interleaving depth supported by the customer's hardware.
OBJECT-TYPE    
  SheAdslLineConfIntDephtType  

sheAdslLineConfExtnProfileControlFullRetrain 1.3.6.1.4.1.231.7.1.2.1.6.1.1.7.37
This object is used to Indicate enable/disable of auto retrain capability. NE will not accept any changes and use always default value!
OBJECT-TYPE    
  SheAdslLineConfEnableSpecial3Type  

sheAdslLineConfExtnProfileControlAdvertisedCapabilities 1.3.6.1.4.1.231.7.1.2.1.6.1.1.7.38
Controls if the CO will attempt to startup using alternate standards if the CPE does not support ADSL+. New with R2.8: If the used annexType was set to 'dynamic', this parameter should be set to 'disabled' or 'adslPlus'. All other values will not work with the intended set of dynamic annexType selection by IU.
OBJECT-TYPE    
  SheAdslLineConfAdvertisedCapabilitiesType  

sheAdslLineConfExtnProfileControlPsdMaskType 1.3.6.1.4.1.231.7.1.2.1.6.1.1.7.39
Selects the PSD mask option to be used.
OBJECT-TYPE    
  SheAdslLineConfPsdMaskType  

sheAdslLineConfExtnProfileControlLineDmtConfMode 1.3.6.1.4.1.231.7.1.2.1.6.1.1.7.40
Selects if there is overlap or no overlap of bins. Overlapping is only supported by non ISDN profiles and will change the setting for TxStartBin accordingly!!. New with R2.8: If the used annexType was set to 'dynamic', this parameter should be set to 'fdmMode' only. Other values will not work with the intended set of dynamic annexType selection by IU.
OBJECT-TYPE    
  SheAdslLineConfLineDmtConfModeType  

sheAdslLineConfExtnProfileControlEraseProfiles 1.3.6.1.4.1.231.7.1.2.1.6.1.1.7.41
Enables/Disables the ability to erase all fast retrain profiles at startup.
OBJECT-TYPE    
  SheAdslLineConfEnableSpecial2Type  

sheAdslLineConfExtnProfileControlParamHybridLossTestStart 1.3.6.1.4.1.231.7.1.2.1.6.1.1.7.43
Indicates Start bin for range of bins to be measured.
OBJECT-TYPE    
  INTEGER 0..511  

sheAdslLineConfExtnProfileControlParamHybridLossTestEnd 1.3.6.1.4.1.231.7.1.2.1.6.1.1.7.44
Indicates End bin for range of bins to be measured.
OBJECT-TYPE    
  INTEGER 0..511  

sheAdslLineConfExtnProfileControlConfMinInp 1.3.6.1.4.1.231.7.1.2.1.6.1.1.7.45
Look at table.
OBJECT-TYPE    
  SheAdslConfMinInpType  

sheAdslLineConfExtnProfileControlRfiBandMask 1.3.6.1.4.1.231.7.1.2.1.6.1.1.7.46
BitMask for sheAdslRfiBandIndex in sheAdslRfiBandTable.
OBJECT-TYPE    
  OCTET STRING Size(4)  

sheAdslLineConfExtnProfileControlUpstreamPsdMaskSelection 1.3.6.1.4.1.231.7.1.2.1.6.1.1.7.47
This configuration parameter defines which upstream PSD mask is enabled. This parameter is used only for annexes J and M of ITU-T Recs. G.992-3 and G.992.5
OBJECT-TYPE    
  SheAdslLineConfUpstreamPSDMaskSelectionType  

sheAdslLineConfExtnProfileControlMaxNomPsdDs 1.3.6.1.4.1.231.7.1.2.1.6.1.1.7.48
The maximum nominal transmit PSD in the downstream direction during initialization and Showtime. It ranges from -600 to -300 units of 0.1 dBm/Hz. (physical values are -60 to -30 dBm/Hz).
OBJECT-TYPE    
  INTEGER -600..-300  

sheAdslLineConfExtnProfileControlMaxNomAtpDs 1.3.6.1.4.1.231.7.1.2.1.6.1.1.7.49
The maximum nominal aggregate transmit power in the downstream direction during initialization and Showtime. It ranges from 0 to 255 units of 0.1 dBm (physical values are 0 to 25.5 dBm).
OBJECT-TYPE    
  Gauge32 0..255  

sheAdslLineConfExtnProfileControlPsdMaskDs 1.3.6.1.4.1.231.7.1.2.1.6.1.1.7.50
The downstream PSD mask applicable at the U-C2 reference point. This parameter is used only for G.992.5 and it may impose PSD restrictions (breakpoints) in addition to the Limit PSD mask defined in G.992.5. This is a string of 32 pairs of values in the following structure: Octets 0+1 - Index of 1st sub-carrier used in the context of a first breakpoint. Octet 2 - The PSD reduction for the sub-carrier indicated in octets 0 and 1. Octets 3-5 - Same, for a 2nd breakpoint. Octets 6-8 - Same, for a 3rd breakpoint. This architecture continues until octets 94-95, which are associated with a 32nd breakpoint. Each subcarrier index is an unsigned number in the range 1 and NSCds. Each PSD reduction value is in the range 0 (0dBm/Hz) to 255 (-127.5dBm/Hz) with steps of 0.5dBm/Hz. Valid values are in the range 0 to 190 (0 to -95dBm/Hz). But the range of start-bin and end-bin is in range 0 to 195 (0 to -97.5dBm/Hz). Two break points (6 byte) are reserved for start sub-carrier index and end sub-carrier index. So the range of size is 6 up to 96. When the number of breakpoints is less than 32, all remaining octets are set to the value 0. Note that the content of this object should be correlated with the sub-carriers mask and with the RFI setup.
OBJECT-TYPE    
  OCTET STRING Size(6..96)  

sheAdslLineConfExtnProfileControlPSDMASKdsEnable 1.3.6.1.4.1.231.7.1.2.1.6.1.1.7.51
User custom PSD mask-related parameter used by the ATU-C to use user custom PSD mask. (Not available for ADSL but ADSL2 and ADSL2plus ).
OBJECT-TYPE    
  SheAdslLineConfEnableType  

sheAdslLineConfExtnProfileControlPSDMASKdsRequestResult 1.3.6.1.4.1.231.7.1.2.1.6.1.1.7.52
The result of the last psd commmand
OBJECT-TYPE    
  SheAdslControlPSDMASKdsRequestResultType  

sheAdslLineConfExtnProfileControlConfMinInpUs 1.3.6.1.4.1.231.7.1.2.1.6.1.1.7.53
Look at table.
OBJECT-TYPE    
  SheAdslConfMinInpType  

sheAdslLineTable 1.3.6.1.4.1.231.7.1.2.1.6.1.1.8
This table includes common attributes describing both ends of the line. It is required for all ADSL physical interfaces. ADSL physical interfaces are those ifEntries where ifType is equal to adsl(94).
OBJECT-TYPE    
  SEQUENCE OF  
    SheAdslLineEntry

sheAdslLineEntry 1.3.6.1.4.1.231.7.1.2.1.6.1.1.8.1
An entry in adslLineTable.
OBJECT-TYPE    
  SheAdslLineEntry  

sheAdslLineCoding 1.3.6.1.4.1.231.7.1.2.1.6.1.1.8.1.1
Specifies the ADSL coding type used on this line.
OBJECT-TYPE    
  AdslLineCodingType  

sheAdslLineType 1.3.6.1.4.1.231.7.1.2.1.6.1.1.8.1.2
Shows the type of ADSL physical line entity that exists, by defining whether and how the line is channelized. If the line is channelized, the value will be other than noChannel(1). This object shows which channel type(s) are currently supported. This values are possible: no channels exist (maybe line is not accessible) fast channel exists only (singleLatency) interleaved channel exists only (singleLatency) fast and interleaved channel exist (dualLatency)
OBJECT-TYPE    
  SheAdslConfLineType  

sheAdslLineSpecific 1.3.6.1.4.1.231.7.1.2.1.6.1.1.8.1.3
OID instance in vendor-specific MIB. The Instance may be used to determine shelf/slot/port of the ATUC interface in a DSLAM.
OBJECT-TYPE    
  VariablePointer  

sheAdslLineConfProfile 1.3.6.1.4.1.231.7.1.2.1.6.1.1.8.1.4
The value of this object identifies the row in the ADSL Line Configuration Profile Table, which applies for this ADSL line, and channels if applicable. A 'DEFVAL' profile will always be exist and set per default.
OBJECT-TYPE    
  SnmpAdminString Size(1..32)  

sheAdslLineAlarmConfProfile 1.3.6.1.4.1.231.7.1.2.1.6.1.1.8.1.6
The value of this object identifies the row in the ADSL Line Alarm Configuration Profile Table, which applies to this ADSL line, and channels if applicable. A 'DEFAULT' profile will always be exist and set.
OBJECT-TYPE    
  SnmpAdminString Size(1..32)  

sheAdslLineAction 1.3.6.1.4.1.231.7.1.2.1.6.1.1.8.1.7
This object indicates parameter that allows actions on a per line basis. These actions include abort, startup, and tests.
OBJECT-TYPE    
  SheAdslLineActionType  

sheAdslLineLineDmtTrellis 1.3.6.1.4.1.231.7.1.2.1.6.1.1.8.1.8
Parameter that indicates whether trellis coding has been enabled or disabled. Trellis coding should always be enabled for its clear performance advantage. trellisOn(1), trellisOff(2)
OBJECT-TYPE    
  SheAdslLineTrellisModeType  

sheAdslLineUtopiaL2RxAddr 1.3.6.1.4.1.231.7.1.2.1.6.1.1.8.1.9
This object indicates UTOPIA Level 2 Rx address for a line.
OBJECT-TYPE    
  INTEGER 1..255  

sheAdslLineUtopiaL2TxAddr 1.3.6.1.4.1.231.7.1.2.1.6.1.1.8.1.10
This object indicates UTOPIA Level 2 Tx address for a line.
OBJECT-TYPE    
  INTEGER 1..255  

sheAdslLineClockType 1.3.6.1.4.1.231.7.1.2.1.6.1.1.8.1.12
This object indicates parameter to set use of either crystal or oscillator.
OBJECT-TYPE    
  SheAdslLineClockType  

sheAdslLineAtucCapability 1.3.6.1.4.1.231.7.1.2.1.6.1.1.8.1.13
The capability of co-side. Be aware that multiple bits could be set! Each bit set to 1 means, that the corresponding standart is supported.
OBJECT-TYPE    
  SheAdslAtuxCapabilityType  

sheAdslLineAturCapability 1.3.6.1.4.1.231.7.1.2.1.6.1.1.8.1.14
The capability of remote-side. Only available if line has trained - otherwise 0. Be aware that multiple bits could be set! Each bit set to 1 means, that the corresponding standart is supported.
OBJECT-TYPE    
  SheAdslAtuxCapabilityType  

sheAdslLineAtuActualCapability 1.3.6.1.4.1.231.7.1.2.1.6.1.1.8.1.15
The actual used capability of the line. Only available if line has trained - otherwise 0. Each bit set to 1 means, that the corresponding standart is supported.
OBJECT-TYPE    
  SheAdslAtuxCapabilityType  

sheAdslLinePwrMgmtPMSF 1.3.6.1.4.1.231.7.1.2.1.6.1.1.8.1.16
This object indicates the action that forces a change in the line state of power management. (Not available for ADSL G992.1) Valid values: pmsfL0ToL2StateForce(1) -> testmode, set running line to L2 power safe mode pmsfL2ToL0StateForce(3) -> switch back line from L2 power safe mode to full power L0 state The transitions pmsfL3ToL0StateForce (unlock) and pmsfL3StateForce (lock) should always be done via ifAdminState setting.
OBJECT-TYPE    
  SheAdslPwrMgmtPMSFType  

sheAdslLineDeltConfLDSF 1.3.6.1.4.1.231.7.1.2.1.6.1.1.8.1.17
DELT-related parameter used by the ATU-C to force the line into loop diagnostics mode. (Not available for ADSL but ADSL2 and ADSL2plus ).
OBJECT-TYPE    
  SheAdslLineDeltConfLDSFType  

sheAdslLineRfiBandMask 1.3.6.1.4.1.231.7.1.2.1.6.1.1.8.1.18
BitMask for used sheAdslRfiBandIndex. A Bit-Position correspond's with an index in sheAdslRfiBandTable and mark configured RFI bands they are used for this profile.
OBJECT-TYPE    
  OCTET STRING Size(4)  

sheAdslLineDpboProfile 1.3.6.1.4.1.231.7.1.2.1.6.1.1.8.1.19
The value of this object identifies the row in the AdslLineDpboProfile Table, which applies for this ADSL line. No 'DEFVAL' profile will exist. Per default no profile is assigned!
OBJECT-TYPE    
  SnmpAdminString Size(0..32)  

sheAdslLineControl 1.3.6.1.4.1.231.7.1.2.1.6.1.1.9
OBJECT IDENTIFIER    

sheAdslLineControlRequest 1.3.6.1.4.1.231.7.1.2.1.6.1.1.9.1
modifyAdslLineEntry: sheAdslLineControlIndex sheAdslLineControlConfProfile sheAdslLineControlAction modifyAdslLineAlarmConfProfileEntry: sheAdslLineControlIndex sheAdslLineControlAlarmConfProfile forceAdslLinePwrMgmtState: vheAdslLineControlIndex sheAdslLineControlPwrMgmtPMSF modifyAdslLineDeltConfEntry: sheAdslLineControlIndex sheAdslLineControlDeltConfLDSF modifyAdslLineRfiBandMask: sheAdslLineControlIndex sheAdslLineControlRfiBandMask ##New for SHR R2.6 setAdslLineDpboProfileEntry: sheAdslLineControlIndex sheAdslLineControlDpboProfile
OBJECT-TYPE    
  SheAdslControlRequestType  

sheAdslLineControlIndex 1.3.6.1.4.1.231.7.1.2.1.6.1.1.9.2
IfIndex of the configured adsl-interface.
OBJECT-TYPE    
  Integer32  

sheAdslLineControlStatus 1.3.6.1.4.1.231.7.1.2.1.6.1.1.9.3
The status of a user command.
OBJECT-TYPE    
  SheControlStatusType  

sheAdslLineControlTimer 1.3.6.1.4.1.231.7.1.2.1.6.1.1.9.4
The maximum wait time for the manager for a long running user command.
OBJECT-TYPE    
  Gauge32  

sheAdslLineControlReqResult 1.3.6.1.4.1.231.7.1.2.1.6.1.1.9.5
The result of the last user command.
OBJECT-TYPE    
  SheAdslControlRequestResultType  

sheAdslLineControlTimeStamp 1.3.6.1.4.1.231.7.1.2.1.6.1.1.9.6
The time stamp of the last command (end of command).
OBJECT-TYPE    
  Unsigned32  

sheAdslLineControlConfProfile 1.3.6.1.4.1.231.7.1.2.1.6.1.1.9.7
The value of this object identifies the row in the ADSL Line Configuration Profile Table, (adslLineConfProfileTable), which applies for this ADSL line, and channels if applicable. For the used `dynamic' mode, in the case which the configuration profile has not been set, the value will be set to `DEFVAL'.
OBJECT-TYPE    
  SnmpAdminString Size(1..32)  

sheAdslLineControlAlarmConfProfile 1.3.6.1.4.1.231.7.1.2.1.6.1.1.9.9
The value of this object identifies the row in the ADSL Line Alarm Configuration Profile Table, (adslLineAlarmConfProfileTable), which applies to this ADSL line, and channels if applicable. For the used `dynamic' mode, in the case which the alarm profile has not been set, the value will be set to `DEFVAL'.
OBJECT-TYPE    
  SnmpAdminString Size(1..32)  

sheAdslLineControlAction 1.3.6.1.4.1.231.7.1.2.1.6.1.1.9.10
This object indicates parameter that allows actions on a per line basis. These actions include abort, startup, and tests.
OBJECT-TYPE    
  SheAdslLineActionType  

sheAdslLineControlPwrMgmtPMSF 1.3.6.1.4.1.231.7.1.2.1.6.1.1.9.11
Force a change in the line state of power management. (Not available for ADSL G992.1) Valid values: pmsfL0ToL2StateForce(1) -> testmode, set running line to L2 power safe mode pmsfL2ToL0StateForce(3) -> switch back line from L2 power safe mode to full power L0 state The transitions pmsfL3ToL0StateForce (unlock) and pmsfL3StateForce (lock) should always be done via ifAdminState setting.
OBJECT-TYPE    
  SheAdslPwrMgmtPMSFType  

sheAdslLineControlDeltConfLDSF 1.3.6.1.4.1.231.7.1.2.1.6.1.1.9.12
DELT-related parameter used by the ATU-C to force the line into loop diagnostics mode. (Not available for ADSL but ADSL2 and ADSL2plus ).
OBJECT-TYPE    
  SheAdslLineDeltConfLDSFType  

sheAdslLineControlRfiBandMask 1.3.6.1.4.1.231.7.1.2.1.6.1.1.9.13
BitMask for sheAdslRfiBandIndex in sheAdslRfiBandTable.
OBJECT-TYPE    
  OCTET STRING Size(0..4)  

sheAdslLineControlDpboProfile 1.3.6.1.4.1.231.7.1.2.1.6.1.1.9.14
The value of this object identifies the row in the AdslLineDpboProfile Table, which applies for this ADSL line.
OBJECT-TYPE    
  SnmpAdminString Size(0..32)  

sheAdslAtucPhysTable 1.3.6.1.4.1.231.7.1.2.1.6.1.1.10
This table provides one row for each ATUC. Each row contains the Physical Layer Parameters table for that ATUC. ADSL physical interfaces are those ifEntries where ifType is equal to adsl(94).
OBJECT-TYPE    
  SEQUENCE OF  
    SheAdslAtucPhysEntry

sheAdslAtucPhysEntry 1.3.6.1.4.1.231.7.1.2.1.6.1.1.10.1
An entry in the adslAtucPhysTable.
OBJECT-TYPE    
  SheAdslAtucPhysEntry  

sheAdslAtucPhysInvSerialNumber 1.3.6.1.4.1.231.7.1.2.1.6.1.1.10.1.1
The vendor specific string that identifies the vendor equipment.
OBJECT-TYPE    
  SnmpAdminString Size(0..32)  

sheAdslAtucPhysInvVendorID 1.3.6.1.4.1.231.7.1.2.1.6.1.1.10.1.2
The vendor ID code is a copy of the binary vendor identification field defined by the PHY[10] and expressed as readable characters.
OBJECT-TYPE    
  SnmpAdminString Size(0..16)  

sheAdslAtucPhysInvVersionNumber 1.3.6.1.4.1.231.7.1.2.1.6.1.1.10.1.3
The vendor specific version number sent by this ATU as part of the initialization messages. It is a copy of the binary version number field defined by the PHY[10] and expressed as readable characters.
OBJECT-TYPE    
  SnmpAdminString Size(0..16)  

sheAdslAtucPhysCurrSnrMgn 1.3.6.1.4.1.231.7.1.2.1.6.1.1.10.1.4
Noise Margin as seen by this ATU with respect to its received signal in tenth dB.
OBJECT-TYPE    
  INTEGER -640..640  

sheAdslAtucPhysCurrAtn 1.3.6.1.4.1.231.7.1.2.1.6.1.1.10.1.5
Measured difference in the total power transmitted by the peer ATU and the total power received by this ATU.
OBJECT-TYPE    
  Gauge32 0..630  

sheAdslAtucPhysCurrStatus 1.3.6.1.4.1.231.7.1.2.1.6.1.1.10.1.6
Indicates current state of the ATUC line. This is a bit-map of possible conditions. The various bit positions are: 0 noDefect There no defects on the line 1 lossOfFraming ATUC failure due to not receiving valid frame. 2 lossOfSignal ATUC failure due to not receiving signal. 3 lossOfPower ATUC failure due to loss of power. Note: the Agent may still function. 4 lossOfSignalQuality Loss of Signal Quality is declared when the Noise Margin falls below the Minimum Noise Margin, or the bit-error-rate exceeds 10^-7. 5 lossOfLink ATUC failure due to inability to link with ATUR. 6 dataInitFailure ATUC failure during initialization due to bit errors corrupting startup exchange data. 7 configInitFailure ATUC failure during initialization due to peer ATU not able to support requested configuration 8 protocolInitFailure ATUC failure during initialization due to incompatible protocol used by the peer ATU. 9 noPeerAtuPresent ATUC failure during initialization due to no activation sequence detected from peer ATU. This is intended to supplement ifOperStatus.
OBJECT-TYPE    
  SheAdslLineCurrentStatusType  

sheAdslAtucPhysCurrOutputPwr 1.3.6.1.4.1.231.7.1.2.1.6.1.1.10.1.7
Measured total output power transmitted by this ATU. This is the measurement that was reported during the last activation sequence.
OBJECT-TYPE    
  INTEGER -310..310  

sheAdslAtucPhysCurrAttainableRate 1.3.6.1.4.1.231.7.1.2.1.6.1.1.10.1.8
Indicates the maximum currently attainable data rate by the ATU. This value will be equal or greater than the current line rate.
OBJECT-TYPE    
  Gauge32  

sheAdslAtucPhysOpState 1.3.6.1.4.1.231.7.1.2.1.6.1.1.10.1.9
This object indicates the operational state of the ATU. Values include idle,handshake, training, Delt mode (loop diagnostic mode), etc. idle(0), data(1), bootUpLoad(8), handshake(16), training(24), framerSync(26), fastRetrainInProg(27), llTest(128), dlTest(131), txTest(132), atmLpTest(133), discovery(46), deltTraining(139), delt(140)
OBJECT-TYPE    
  SheAdslLineOpStateType  

sheAdslAtucPhysActualStd 1.3.6.1.4.1.231.7.1.2.1.6.1.1.10.1.10
This object provides actual ATU-C configuration based on outcome of negotiation with ATU-R. In this case, the parameter provides actual standard used for the connection.
OBJECT-TYPE    
  SheAdslLineConfStandardType  

sheAdslAtucPhysBertError 1.3.6.1.4.1.231.7.1.2.1.6.1.1.10.1.11
This object indicates the No. of bit errors detected during BERT.
OBJECT-TYPE    
  Unsigned32  

sheAdslAtucPhysTxAtmCellCounter 1.3.6.1.4.1.231.7.1.2.1.6.1.1.10.1.12
This object Provides transmit ATM cell counter.
OBJECT-TYPE    
  Counter32  

sheAdslAtucPhysRxAtmCellCounter 1.3.6.1.4.1.231.7.1.2.1.6.1.1.10.1.13
This object Provides receive ATM cell counter.
OBJECT-TYPE    
  Unsigned32  

sheAdslAtucPhysStartProgress 1.3.6.1.4.1.231.7.1.2.1.6.1.1.10.1.14
This object provides current detailed start up information to be used for debugging.
OBJECT-TYPE    
  Unsigned32  

sheAdslAtucPhysIdleBertError 1.3.6.1.4.1.231.7.1.2.1.6.1.1.10.1.15
Number of bit errors.
OBJECT-TYPE    
  Unsigned32  

sheAdslAtucPhysIdleBertCells 1.3.6.1.4.1.231.7.1.2.1.6.1.1.10.1.16
Number of idle cells.
OBJECT-TYPE    
  Unsigned32  

sheAdslAtucPhysBertSync 1.3.6.1.4.1.231.7.1.2.1.6.1.1.10.1.17
Indicates if the Signal is in Sync or not.
OBJECT-TYPE    
  SheAdslAtucPhysBertSyncType  

sheAdslAtucPhysParametricTestResult 1.3.6.1.4.1.231.7.1.2.1.6.1.1.10.1.18
Indicates the Result of the Parametric Test conducted on the Xcvr.
OBJECT-TYPE    
  SheAdslAtucPhysParametricTestResultType  

sheAdslAtucPwrMgmtState 1.3.6.1.4.1.231.7.1.2.1.6.1.1.10.1.19
Line Power Management State. (Not valid for ADSL G992.1)
OBJECT-TYPE    
  SheAdslPwrMgmtStateType  

sheAdslAtucPhysDeltHLINSCus 1.3.6.1.4.1.231.7.1.2.1.6.1.1.10.1.20
DELT-related parameter that provides the scale factor to be applied to the upstream Hlin(f) values. Only available after a loop diagnostic procedure. (Not available for ADSL but ADSL2 & ADSL2plus).
OBJECT-TYPE    
  Unsigned32  

sheAdslAtucPhysDeltHLINpsus 1.3.6.1.4.1.231.7.1.2.1.6.1.1.10.1.21
DELT-related parameter that provides an array of complex upstream Hlin(f) values in linear scale. Every two octects refer to one element in this array of octets. (Not available for ADSL but ADSL2 & ADSL2plus). This parameter is an array of complex upstream Hlin(f) values in linear scale. Each array entry represents the Hlin(f = i*HLINGus* delta(f)) value for a particular subcarrier group index i, ranging from 0 to MIN(NSCus - 1,511). The Hlin(f) is represented as ((scale/2(exp15))*((a(i) + j*b(i))/2(exp15))), with scale being coded as a 16-bit unsigned integer and, a(i) and b(i) coded as 16-bit 2s complement signed integers in the (-2(exp15) + 1) to (+2(exp15) - 1) range. A special value a(i) = b(i) = -2(exp15) indicates that no measurement could be done for this subcarrier group because it is out of the passband or that the attenuation is out of range to be represented. This parameter is only available after a loop diagnostic procedure.
OBJECT-TYPE    
  OCTET STRING Size(0..128)  

sheAdslAtucPhysDeltHLOGMTus 1.3.6.1.4.1.231.7.1.2.1.6.1.1.10.1.22
DELT-related parameter that provides the number of symbols used to measure the upstream Hlog(f). (Not available for ADSL but ADSL2 & ADSL2plus).
OBJECT-TYPE    
  Unsigned32  

sheAdslAtucPhysDeltHLOGpsus 1.3.6.1.4.1.231.7.1.2.1.6.1.1.10.1.23
DELT-related parameter that provides an array of real upstream Hlog(f) values in dB. (Not available for ADSL but ADSL2 & ADSL2plus). This parameter is an array of real upstream Hlog(f) values in dB. Each array entry represents the real Hlog(f = i*HLOGGus* delta(f)) value for a particular subcarrier group sub-carrier index i, ranging from 0 to MIN(NSCus - 1,511). The real Hlog(f) value is represented as (6 - m(i)/10), with m(i) 10-bit unsigned integer in the 0 to 1022 range. A special value m = 1023 indicates that no measurement could be done for this subcarrier group because it is out of the passband or that the attenuation is out of range to be represented.
OBJECT-TYPE    
  OCTET STRING Size(0..64)  

sheAdslAtucPhysDeltQLNMTus 1.3.6.1.4.1.231.7.1.2.1.6.1.1.10.1.24
DELT-related parameter that provides the number of symbols used to measure the upstream QLN(f) values. (Not available for ADSL but ADSL2 & ADSL2plus).
OBJECT-TYPE    
  Unsigned32  

sheAdslAtucPhysDeltQLNpsus 1.3.6.1.4.1.231.7.1.2.1.6.1.1.10.1.25
DELT-related parameter that provides an array of real upstream QLN(f) values in dBm/Hz. Every two octects refer to one element in this array of octets. (Not available for ADSL but ADSL2 & ADSL2plus) This parameter is an array of real upstream QLN(f) values in dBm/Hz. Each array entry represents the QLN(f = i*QLNGus* delta(f)) value for a particular subcarrier group index i, ranging from 0 to MIN(NSCus - 1,511). The QLN(f) is represented as (-23 - n(i)/2), with n(i) an 8-bit unsigned integer in the 0 to 254 range. A special value n(i) = 255 indicates that no measurement could be done for this subcarrier group because it is out of the passband or that the noise PSD is out of range to be represented.
OBJECT-TYPE    
  OCTET STRING Size(0..32)  

sheAdslAtucPhysActState 1.3.6.1.4.1.231.7.1.2.1.6.1.1.10.1.26
This object indicates the result of the ATU's line activation. Values include no error etc.
OBJECT-TYPE    
  SheAdslLineActStateType  

sheAdslAtucPhysCurrentBinStatus 1.3.6.1.4.1.231.7.1.2.1.6.1.1.10.1.27
This parameter represent the current bin status of used subcarriers. Each octet map to the corresponding bin.
OBJECT-TYPE    
  OCTET STRING Size(0..512)  

sheAdslAtucPhysCurrentBinBitLoading 1.3.6.1.4.1.231.7.1.2.1.6.1.1.10.1.28
This parameter represent the current used bit loading per bin in upstream direction. Each octet map to the corresponding bin.
OBJECT-TYPE    
  OCTET STRING Size(0..64)  

sheAdslAtucPhysDeltSNRMTus 1.3.6.1.4.1.231.7.1.2.1.6.1.1.10.1.29
DELT-related parameter that provides the number of symbols used to measure the upstream SNR(f) values. (Not available for ADSL and ADSL2plus) It is represented as a 16-bit unsigned value. After a loop diagnostic procedure, this parameter shall contain the number of symbols used to generate the associate parameter. It should correspond to the value specified in the Recommendation (e.g., the number of symbols in 1 s time interval for G.992.3).
OBJECT-TYPE    
  Unsigned32  

sheAdslAtucPhysDeltDMTBinSNRus 1.3.6.1.4.1.231.7.1.2.1.6.1.1.10.1.30
DELT-related parameter that provides an array of real upstream SNR(f) values in dB (Not available for ADSL and ADSL2plus) It is coded in the same way as the related downstream parameter.
OBJECT-TYPE    
  OCTET STRING Size(0..64)  

sheAdslAtucPhysDeltLastTxState 1.3.6.1.4.1.231.7.1.2.1.6.1.1.10.1.31
DELT-related parameter that provides last successful transmitted initialization state by the ATU-C. (Not available for ADSL and ADSL2plus) Initialization states are defined in the individual ADSL Recommendations and are counted from 0 (if G.994.1 is used) or 1 (if G.994.1 is not used) up to Showtime. This parameter must be interpreted along with the ADSL Transmission System. This parameter is available only when, after a failed full initialization, the line diagnostics procedures are activated on the line. Line diagnostics procedures can be activated by the operator of the system (through the Line State Forced line configuration parameter) or autonomously by the ATU-C or ATU-R.
OBJECT-TYPE    
  SheAdslPhysAtucDeltLastTxStateType  

sheAdslAtucPhysDeltSATNus 1.3.6.1.4.1.231.7.1.2.1.6.1.1.10.1.32
DELT-related parameter that provides the uptream signal attenuation (length = 4 bytes). (Not available for ADSL and ADSL2plus). This parameter is the measured difference in dB in the total power transmitted by the ATU-R and the total power received by the ATU-C over all subcarriers during showtime. The upstream line attenuation ranges from 0 to +127 dB with 0.1 dB steps. A special value indicates the line attenuation is out of range to be represented. NOTE: During showtime, only a subset of the subcarriers may be transmitted by the ATU-R, as compared to diagnostics mode and initialization. Therefore, the upstream Signal attenuation may be significantly lower than the upstream Line attenuation.
OBJECT-TYPE    
  Unsigned32 0..1270  

sheAdslAtucChanTable 1.3.6.1.4.1.231.7.1.2.1.6.1.1.11
This table provides one row for each ATUC channel.
OBJECT-TYPE    
  SEQUENCE OF  
    SheAdslAtucChanEntry

sheAdslAtucChanEntry 1.3.6.1.4.1.231.7.1.2.1.6.1.1.11.1
An entry in the adslAtucChanTable. This table is only supported by NE releases smaller then R2.5 (NO dualLatency support)!!
OBJECT-TYPE    
  SheAdslAtucChanEntry  

sheAdslAtucChanInterleaveDelay 1.3.6.1.4.1.231.7.1.2.1.6.1.1.11.1.1
Interleave Delay for this channel. Interleave delay applies only to the interleave channel and defines the mapping (relative spacing) between subsequent input bytes at the interleaver input and their placement in the bit stream at the interleaver output. Larger numbers provide greater separation between consecutive input bytes in the output bit stream allowing for improved impulse noise immunity at the expense of payload latency. In the case where the ifType is Fast(125), use noSuchObject.
OBJECT-TYPE    
  Gauge32  

sheAdslAtucChanCurrTxRate 1.3.6.1.4.1.231.7.1.2.1.6.1.1.11.1.2
Actual transmit rate on this channel.
OBJECT-TYPE    
  Gauge32 1..32736  

sheAdslAtucChanPrevTxRate 1.3.6.1.4.1.231.7.1.2.1.6.1.1.11.1.3
The rate at the time of the last adslAtucRateChangeTrap event. It is also set at initialization to prevent a trap being sent. Rate changes less than adslAtucThresh(*)RateDown or less than adslAtucThresh(*)RateUp will not cause a trap or cause this object to change. (*) == Fast or Interleave. See AdslLineAlarmConfProfileEntry.
OBJECT-TYPE    
  Gauge32 1..32736  

sheAdslAtucChanCrcBlockLength 1.3.6.1.4.1.231.7.1.2.1.6.1.1.11.1.4
Indicates the length of the channel data-block on which the CRC operates. Refer to Line Code Specific MIBs, [11] and [12] for more information.
OBJECT-TYPE    
  Gauge32  

sheAdslAtucChanCurrAtmStatus 1.3.6.1.4.1.231.7.1.2.1.6.1.1.11.1.5
indicates an ncd or lcd failure if the counter surpasses 127. If neither ATM counter surpasses 127, the return value will be 'NoAtmDefect'. noAtmDefect(0), noCellDeleniation(1), lossOfCellDeleniation(2)
OBJECT-TYPE    
  SheAdslLineAtmStatus  

sheAdslAtucChanRsSymbols 1.3.6.1.4.1.231.7.1.2.1.6.1.1.11.1.6
Indicates number of DMT symbols per Reed-Solomon code word (S) in the downstream direction. Note that S is not restricted to interleaved mode only. Even in fast mode, S is a valid constant value and is equal to 1.
OBJECT-TYPE    
  Unsigned32  

sheAdslAtucChanRsDepth 1.3.6.1.4.1.231.7.1.2.1.6.1.1.11.1.7
Indicates interleaving depth (D) in the downstream direction. Note that D is not restricted to interleaved mode only. Even in fast mode, D is a valid constant value and is equal to 1.
OBJECT-TYPE    
  Unsigned32  

sheAdslAtucChanRsRedundancy 1.3.6.1.4.1.231.7.1.2.1.6.1.1.11.1.8
Indicates number of redundant bytes (R) per Reed-Solomon code in the downstream direction.
OBJECT-TYPE    
  Unsigned32  

sheAdslAtucPerfDataTable 1.3.6.1.4.1.231.7.1.2.1.6.1.1.12
This table provides one row for each ATUC. ADSL physical interfaces are those ifEntries where ifType is equal to adsl(94).
OBJECT-TYPE    
  SEQUENCE OF  
    SheAdslAtucPerfDataEntry

sheAdslAtucPerfDataEntry 1.3.6.1.4.1.231.7.1.2.1.6.1.1.12.1
An entry in adslAtucPerfDataTable.
OBJECT-TYPE    
  SheAdslAtucPerfDataEntry  

sheAdslAtucPerfDataLofs 1.3.6.1.4.1.231.7.1.2.1.6.1.1.12.1.1
Count of the number of Loss of Framing failures since agent reset.
OBJECT-TYPE    
  Counter32  

sheAdslAtucPerfDataLoss 1.3.6.1.4.1.231.7.1.2.1.6.1.1.12.1.2
Count of the number of Loss of Signal failures since agent reset.
OBJECT-TYPE    
  Counter32  

sheAdslAtucPerfDataLols 1.3.6.1.4.1.231.7.1.2.1.6.1.1.12.1.3
Count of the number of Loss of Link failures since agent reset.
OBJECT-TYPE    
  Counter32  

sheAdslAtucPerfDataLprs 1.3.6.1.4.1.231.7.1.2.1.6.1.1.12.1.4
Count of the number of Loss of Power failures since agent reset.
OBJECT-TYPE    
  Counter32  

sheAdslAtucPerfDataESs 1.3.6.1.4.1.231.7.1.2.1.6.1.1.12.1.5
Count of the number of Errored Seconds since agent reset. The errored second parameter is a count of one-second intervals containing one or more crc anomalies, or one or more los or sef defects.
OBJECT-TYPE    
  Counter32  

sheAdslAtucPerfDataInits 1.3.6.1.4.1.231.7.1.2.1.6.1.1.12.1.6
Count of the line initialization attempts since agent reset. Includes both successful and failed attempts.
OBJECT-TYPE    
  Counter32  

sheAdslAtucPerfDataStatFastR 1.3.6.1.4.1.231.7.1.2.1.6.1.1.12.1.7
The value of this object indicates the count of fast retrains.
OBJECT-TYPE    
  Gauge32  

sheAdslAtucPerfDataStatFailedFastR 1.3.6.1.4.1.231.7.1.2.1.6.1.1.12.1.8
The value of this object indicates the count of failed fast retrains.
OBJECT-TYPE    
  Gauge32  

sheAdslAtucPerfDataStatSesL 1.3.6.1.4.1.231.7.1.2.1.6.1.1.12.1.9
The value of this object indicates the count of severely errored second line.
OBJECT-TYPE    
  Gauge32  

sheAdslAtucPerfDataStatUasL 1.3.6.1.4.1.231.7.1.2.1.6.1.1.12.1.10
The value of this object indicates the count of unavailable errored seconds.
OBJECT-TYPE    
  Gauge32  

sheAdslAtucPerfDataValidIntervals 1.3.6.1.4.1.231.7.1.2.1.6.1.1.12.1.11
The number of previous 15-minute intervals in the interval table for which data was collected. Given that is the maximum # of intervals supported. The value will be unless the measurement was (re-)started within the last (*15) minutes, in which case the value will be the number of complete 15 minute intervals for which the agent has at least some data. In certain cases (e.g., in the case where the agent is a proxy) it is possible that some intervals are unavailable. In this case, this interval is the maximum interval number for which data is available.
OBJECT-TYPE    
  INTEGER 0..96  

sheAdslAtucPerfDataInvalidIntervals 1.3.6.1.4.1.231.7.1.2.1.6.1.1.12.1.12
The number of intervals in the range from 0 to the value of adslAtucPerfValidIntervals for which no data is available. This object will typically be zero except in cases where the data for some intervals are not available (e.g., in proxy situations).
OBJECT-TYPE    
  INTEGER 0..96  

sheAdslAtucPerfDataCurr15MinTimeElapsed 1.3.6.1.4.1.231.7.1.2.1.6.1.1.12.1.13
Total elapsed seconds in this interval.
OBJECT-TYPE    
  AdslPerfTimeElapsed 0..899  

sheAdslAtucPerfDataCurr15MinLofs 1.3.6.1.4.1.231.7.1.2.1.6.1.1.12.1.14
Count of seconds in the current 15 minute interval when there was Loss of Framing.
OBJECT-TYPE    
  PerfCurrentCount  

sheAdslAtucPerfDataCurr15MinLoss 1.3.6.1.4.1.231.7.1.2.1.6.1.1.12.1.15
Count of seconds in the current 15 minute interval when there was Loss of Signal.
OBJECT-TYPE    
  PerfCurrentCount  

sheAdslAtucPerfDataCurr15MinLols 1.3.6.1.4.1.231.7.1.2.1.6.1.1.12.1.16
Count of seconds in the current 15 minute interval when there was Loss of Link.
OBJECT-TYPE    
  PerfCurrentCount  

sheAdslAtucPerfDataCurr15MinLprs 1.3.6.1.4.1.231.7.1.2.1.6.1.1.12.1.17
Count of seconds in the current 15 minute interval when there was Loss of Power.
OBJECT-TYPE    
  PerfCurrentCount  

sheAdslAtucPerfDataCurr15MinESs 1.3.6.1.4.1.231.7.1.2.1.6.1.1.12.1.18
Count of Errored Seconds in the current 15 minute interval. The errored second parameter is a count of one-second intervals containing one or more crc anomalies, or one or more los or sef defects.
OBJECT-TYPE    
  PerfCurrentCount  

sheAdslAtucPerfDataCurr15MinInits 1.3.6.1.4.1.231.7.1.2.1.6.1.1.12.1.19
Count of the line initialization attempts in the current 15 minute interval. Includes both successful and failed attempts.
OBJECT-TYPE    
  PerfCurrentCount  

sheAdslAtucPerfDataCurr15MinFastR 1.3.6.1.4.1.231.7.1.2.1.6.1.1.12.1.20
Count of seconds in the current 15 minute interval when there was fast retrains. REFERENCE ITU G.997.1 Section 7.4.15.1
OBJECT-TYPE    
  Gauge32  

sheAdslAtucPerfDataCurr15MinFailedFastR 1.3.6.1.4.1.231.7.1.2.1.6.1.1.12.1.21
Count of seconds in the current 15 minute interval when there was failed fast retrains. REFERENCE ITU G.997.1 Section 7.4.15.2
OBJECT-TYPE    
  Gauge32  

sheAdslAtucPerfDataCurr15MinSesL 1.3.6.1.4.1.231.7.1.2.1.6.1.1.12.1.22
Count of seconds in the current 15 minute interval when there was severely errored seconds. REFERENCE ITU G.997.1 Section 7.2.1.1.7
OBJECT-TYPE    
  Gauge32  

sheAdslAtucPerfDataCurr15MinUasL 1.3.6.1.4.1.231.7.1.2.1.6.1.1.12.1.23
Count of seconds in the current 15 minute interval when there was count for unavailable errored seconds. REFERENCE ITU G.997.1 Section 7.2.1.1.9
OBJECT-TYPE    
  Gauge32  

sheAdslAtucPerfDataCurr1DayTimeElapsed 1.3.6.1.4.1.231.7.1.2.1.6.1.1.12.1.24
Number of seconds that have elapsed since the beginning of the current 1-day interval.
OBJECT-TYPE    
  AdslPerfTimeElapsed 0..86399  

sheAdslAtucPerfDataCurr1DayLofs 1.3.6.1.4.1.231.7.1.2.1.6.1.1.12.1.25
Count of the number of seconds when there was Loss of Framing during the current day as measured by adslAtucPerfCurr1DayTimeElapsed.
OBJECT-TYPE    
  AdslPerfCurrDayCount  

sheAdslAtucPerfDataCurr1DayLoss 1.3.6.1.4.1.231.7.1.2.1.6.1.1.12.1.26
Count of the number of seconds when there was Loss of Signal during the current day as measured by adslAtucPerfCurr1DayTimeElapsed.
OBJECT-TYPE    
  AdslPerfCurrDayCount  

sheAdslAtucPerfDataCurr1DayLols 1.3.6.1.4.1.231.7.1.2.1.6.1.1.12.1.27
Count of the number of seconds when there was Loss of Link during the current day as measured by adslAtucPerfCurr1DayTimeElapsed.
OBJECT-TYPE    
  AdslPerfCurrDayCount  

sheAdslAtucPerfDataCurr1DayLprs 1.3.6.1.4.1.231.7.1.2.1.6.1.1.12.1.28
Count of the number of seconds when there was Loss of Power during the current day as measured by adslAtucPerfCurr1DayTimeElapsed.
OBJECT-TYPE    
  AdslPerfCurrDayCount  

sheAdslAtucPerfDataCurr1DayESs 1.3.6.1.4.1.231.7.1.2.1.6.1.1.12.1.29
Count of Errored Seconds during the current day as measured by adslAtucPerfCurr1DayTimeElapsed. The errored second parameter is a count of one-second intervals containing one or more crc anomalies, or one or more los or sef defects.
OBJECT-TYPE    
  AdslPerfCurrDayCount  

sheAdslAtucPerfDataCurr1DayInits 1.3.6.1.4.1.231.7.1.2.1.6.1.1.12.1.30
Count of the line initialization attempts in the day as measured by adslAtucPerfCurr1DayTimeElapsed. Includes both successful and failed attempts.
OBJECT-TYPE    
  AdslPerfCurrDayCount  

sheAdslAtucPerfDataCurr1DayFastR 1.3.6.1.4.1.231.7.1.2.1.6.1.1.12.1.31
Count of the number of seconds when there was fast retrains during the current day as measured by adslAtucPerfCurr1Day TimeElapsed. REFERENCE ITU G.997.1 Section 7.4.15.1
OBJECT-TYPE    
  Gauge32  

sheAdslAtucPerfDataCurr1DayFailedFastR 1.3.6.1.4.1.231.7.1.2.1.6.1.1.12.1.32
Count of the number of seconds when there was failed fast retrains during the current day as measured by adslAtucPerfCurr1Day TimeElapsed.REFERENCE ITU G.997.1 Section 7.4.15.2
OBJECT-TYPE    
  Gauge32  

sheAdslAtucPerfDataCurr1DaySesL 1.3.6.1.4.1.231.7.1.2.1.6.1.1.12.1.33
Count of the number of seconds when there was Severely Errored Seconds during the current day as measured by adslAtucPerfCurr1DayTimeElapsed. REFERENCE ITU G.997.1 Section 7.2.1.1.7
OBJECT-TYPE    
  Gauge32  

sheAdslAtucPerfDataCurr1DayUasL 1.3.6.1.4.1.231.7.1.2.1.6.1.1.12.1.34
Count of the number of seconds when there was Unavailable Errored Seconds during the current day as measured by adslAtucPerfCurr1DayTimeElapsed. REFERENCE ITU G.997.1 Section 7.2.1.1.9
OBJECT-TYPE    
  Gauge32  

sheAdslAtucPerfDataPrev1DayTimeElapsed 1.3.6.1.4.1.231.7.1.2.1.6.1.1.12.1.35
Total elapsed seconds in this interval in seconds.
OBJECT-TYPE    
  Gauge32  

sheAdslAtucPerfDataPrev1DayMoniSecs 1.3.6.1.4.1.231.7.1.2.1.6.1.1.12.1.36
The amount of time in the previous 1-day interval over which the performance monitoring information is actually counted. This value will be the same as the interval duration except in a situation where performance monitoring data could not be collected for any reason.
OBJECT-TYPE    
  INTEGER 0..86400  

sheAdslAtucPerfDataPrev1DayLofs 1.3.6.1.4.1.231.7.1.2.1.6.1.1.12.1.37
Count of seconds in the interval when there was Loss of Framing within the most recent previous 1-day period.
OBJECT-TYPE    
  AdslPerfPrevDayCount  

sheAdslAtucPerfDataPrev1DayLoss 1.3.6.1.4.1.231.7.1.2.1.6.1.1.12.1.38
Count of seconds in the interval when there was Loss of Signal within the most recent previous 1-day period.
OBJECT-TYPE    
  AdslPerfPrevDayCount  

sheAdslAtucPerfDataPrev1DayLols 1.3.6.1.4.1.231.7.1.2.1.6.1.1.12.1.39
Count of seconds in the interval when there was Loss of Link within the most recent previous 1-day period.
OBJECT-TYPE    
  AdslPerfPrevDayCount  

sheAdslAtucPerfDataPrev1DayLprs 1.3.6.1.4.1.231.7.1.2.1.6.1.1.12.1.40
Count of seconds in the interval when there was Loss of Power within the most recent previous 1-day period.
OBJECT-TYPE    
  AdslPerfPrevDayCount  

sheAdslAtucPerfDataPrev1DayESs 1.3.6.1.4.1.231.7.1.2.1.6.1.1.12.1.41
Count of Errored Seconds within the most recent previous 1-day period. The errored second parameter is a count of one-second intervals containing one or more crc anomalies, or one or more los or sef defects.
OBJECT-TYPE    
  AdslPerfPrevDayCount  

sheAdslAtucPerfDataPrev1DayInits 1.3.6.1.4.1.231.7.1.2.1.6.1.1.12.1.42
Count of the line initialization attempts in the most recent previous 1-day period. Includes both successful and failed attempts.
OBJECT-TYPE    
  AdslPerfPrevDayCount  

sheAdslAtucPerfDataPrev1DayFastR 1.3.6.1.4.1.231.7.1.2.1.6.1.1.12.1.43
Count of seconds in the interval when there was fast retrains within the most recent previous 1 day period. REFERENCE ITU G.997.1 Section 7.4.15.1
OBJECT-TYPE    
  Gauge32  

sheAdslAtucPerfDataPrev1DayFailedFastR 1.3.6.1.4.1.231.7.1.2.1.6.1.1.12.1.44
Count of seconds in the interval when there was failed fast retrains within the most recent previous 1 day period. REFERENCE ITU G.997.1 Section 7.4.15.2
OBJECT-TYPE    
  Gauge32  

sheAdslAtucPerfDataPrev1DaySesL 1.3.6.1.4.1.231.7.1.2.1.6.1.1.12.1.45
Count of seconds in the interval when there was severely errored seconds within the most recent previous 1 day period. REFERENCE ITU G.997.1 Section 7.2.1.1.7
OBJECT-TYPE    
  Gauge32  

sheAdslAtucPerfDataPrev1DayUasL 1.3.6.1.4.1.231.7.1.2.1.6.1.1.12.1.46
Count of seconds in the interval when there was unavailable errored seconds within the most recent previous 1 day period. REFERENCE ITU G.997.1 Section 7.2.1.1.9
OBJECT-TYPE    
  Gauge32  

sheAdslAtucIntervalTable 1.3.6.1.4.1.231.7.1.2.1.6.1.1.13
This table provides one row for each ATUC performance data collection interval. ADSL physical interfaces are those ifEntries where ifType is equal to adsl(94).
OBJECT-TYPE    
  SEQUENCE OF  
    SheAdslAtucIntervalEntry

sheAdslAtucIntervalEntry 1.3.6.1.4.1.231.7.1.2.1.6.1.1.13.1
An entry in the adslAtucIntervalTable.
OBJECT-TYPE    
  SheAdslAtucIntervalEntry  

sheAdslAtucIntervalNumber 1.3.6.1.4.1.231.7.1.2.1.6.1.1.13.1.1
Performance Data Interval number 1 is the the most recent previous interval; interval 96 is 24 hours ago. Intervals 2..96 are optional.
OBJECT-TYPE    
  INTEGER 1..96  

sheAdslAtucIntervalValidData 1.3.6.1.4.1.231.7.1.2.1.6.1.1.13.1.2
This variable indicates if the data for this interval is valid.
OBJECT-TYPE    
  TruthValue  

sheAdslAtucIntervalEndTime 1.3.6.1.4.1.231.7.1.2.1.6.1.1.13.1.3
This variable indicates the time of storing this interval.
OBJECT-TYPE    
  Unsigned32  

sheAdslAtucIntervalLofs 1.3.6.1.4.1.231.7.1.2.1.6.1.1.13.1.4
Count of seconds in the interval when there was Loss of Framing.
OBJECT-TYPE    
  PerfIntervalCount  

sheAdslAtucIntervalLoss 1.3.6.1.4.1.231.7.1.2.1.6.1.1.13.1.5
Count of seconds in the interval when there was Loss of Signal.
OBJECT-TYPE    
  PerfIntervalCount  

sheAdslAtucIntervalLols 1.3.6.1.4.1.231.7.1.2.1.6.1.1.13.1.6
Count of seconds in the interval when there was Loss of Link.
OBJECT-TYPE    
  PerfIntervalCount  

sheAdslAtucIntervalLprs 1.3.6.1.4.1.231.7.1.2.1.6.1.1.13.1.7
Count of seconds in the interval when there was Loss of Power.
OBJECT-TYPE    
  PerfIntervalCount  

sheAdslAtucIntervalESs 1.3.6.1.4.1.231.7.1.2.1.6.1.1.13.1.8
Count of Errored Seconds in the interval. The errored second parameter is a count of one-second intervals containing one or more crc anomalies, or one or more los or sef defects.
OBJECT-TYPE    
  PerfIntervalCount  

sheAdslAtucIntervalInits 1.3.6.1.4.1.231.7.1.2.1.6.1.1.13.1.9
Count of the line initialization attempts during the interval. Includes both successful and failed attempts.
OBJECT-TYPE    
  PerfIntervalCount  

sheAdslAtucIntervalFastR 1.3.6.1.4.1.231.7.1.2.1.6.1.1.13.1.10
This variable indicates Count of seconds in the interval when there was Fast Retrains.
OBJECT-TYPE    
  Gauge32  

sheAdslAtucIntervalFailedFastR 1.3.6.1.4.1.231.7.1.2.1.6.1.1.13.1.11
This variable indicates Count of seconds in the interval when there was Failed Fast Retrains.
OBJECT-TYPE    
  Gauge32  

sheAdslAtucIntervalSesL 1.3.6.1.4.1.231.7.1.2.1.6.1.1.13.1.12
This variable indicates Count of seconds in the interval when there was severely errored seconds.
OBJECT-TYPE    
  Gauge32  

sheAdslAtucIntervalUasL 1.3.6.1.4.1.231.7.1.2.1.6.1.1.13.1.13
This variable indicates Count of seconds in the interval when there was unavailable errored seconds.
OBJECT-TYPE    
  Gauge32  

sheAdslAtucChanPerfDataTable 1.3.6.1.4.1.231.7.1.2.1.6.1.1.14
This table provides one row for each ATUC channel.
OBJECT-TYPE    
  SEQUENCE OF  
    SheAdslAtucChanPerfDataEntry

sheAdslAtucChanPerfDataEntry 1.3.6.1.4.1.231.7.1.2.1.6.1.1.14.1
An entry in adslAtucChanPerfDataTable. This table is only supported by NE releases smaller then R2.5 (NO dualLatency support)!!
OBJECT-TYPE    
  SheAdslAtucChanPerfDataEntry  

sheAdslAtucChanPerfDataTimeElapsed 1.3.6.1.4.1.231.7.1.2.1.6.1.1.14.1.1
Total elapsed seconds in this interval.
OBJECT-TYPE    
  Gauge32  

sheAdslAtucChanPerfDataReceivedBlks 1.3.6.1.4.1.231.7.1.2.1.6.1.1.14.1.2
Count of all encoded blocks received on this channel since agent reset.
OBJECT-TYPE    
  Counter32  

sheAdslAtucChanPerfDataTransmittedBlks 1.3.6.1.4.1.231.7.1.2.1.6.1.1.14.1.3
Count of all encoded blocks transmitted on this channel since agent reset.
OBJECT-TYPE    
  Counter32  

sheAdslAtucChanPerfDataCorrectedBlks 1.3.6.1.4.1.231.7.1.2.1.6.1.1.14.1.4
Count of all blocks received with errors that were corrected since agent reset. These blocks are passed on as good data.
OBJECT-TYPE    
  Counter32  

sheAdslAtucChanPerfDataUncorrectBlks 1.3.6.1.4.1.231.7.1.2.1.6.1.1.14.1.5
Count of all blocks received with uncorrectable errors since agent reset.
OBJECT-TYPE    
  Counter32  

sheAdslAtucChanPerfDataNcd 1.3.6.1.4.1.231.7.1.2.1.6.1.1.14.1.6
Count of no cell delineation(ncd) on this channel.
OBJECT-TYPE    
  Gauge32  

sheAdslAtucChanPerfDataOcd 1.3.6.1.4.1.231.7.1.2.1.6.1.1.14.1.7
Count of out of cell delineation (ocd) on this channel.
OBJECT-TYPE    
  Gauge32  

sheAdslAtucChanPerfDataHec 1.3.6.1.4.1.231.7.1.2.1.6.1.1.14.1.8
Header error check counter(hec) on this channel.
OBJECT-TYPE    
  Gauge32  

sheAdslAtucChanPerfDataValidIntervals 1.3.6.1.4.1.231.7.1.2.1.6.1.1.14.1.9
The number of previous 15-minute intervals in the interval table for which data was collected. Given that is the maximum # of intervals supported. The value will be unless the measurement was (re-)started within the last (*15) minutes, in which case the value will be the number of complete 15 minute intervals for which the agent has at least some data. In certain cases (e.g., in the case where the agent is a proxy) it is possible that some intervals are unavailable. In this case, this interval is the maximum interval number for which data is available.
OBJECT-TYPE    
  INTEGER 0..96  

sheAdslAtucChanPerfDataInvalidIntervals 1.3.6.1.4.1.231.7.1.2.1.6.1.1.14.1.10
The number of intervals in the range from 0 to the value of adslAtucChanPerfValidIntervals for which no data is available. This object will typically be zero except in cases where the data for some intervals are not available (e.g., in proxy situations).
OBJECT-TYPE    
  INTEGER 0..96  

sheAdslAtucChanPerfDataCurr15MinTimeElapsed 1.3.6.1.4.1.231.7.1.2.1.6.1.1.14.1.11
Total elapsed seconds in this interval.
OBJECT-TYPE    
  AdslPerfTimeElapsed 0..899  

sheAdslAtucChanPerfDataCurr15MinReceivedBlks 1.3.6.1.4.1.231.7.1.2.1.6.1.1.14.1.12
Count of all encoded blocks received on this channel within the current 15 minute interval.
OBJECT-TYPE    
  PerfCurrentCount  

sheAdslAtucChanPerfDataCurr15MinTransmittedBlks 1.3.6.1.4.1.231.7.1.2.1.6.1.1.14.1.13
Count of all encoded blocks transmitted on this channel within the current 15 minute interval.
OBJECT-TYPE    
  PerfCurrentCount  

sheAdslAtucChanPerfDataCurr15MinCorrectedBlks 1.3.6.1.4.1.231.7.1.2.1.6.1.1.14.1.14
Count of all blocks received with errors that were corrected on this channel within the current 15 minute interval.
OBJECT-TYPE    
  PerfCurrentCount  

sheAdslAtucChanPerfDataCurr15MinUncorrectBlks 1.3.6.1.4.1.231.7.1.2.1.6.1.1.14.1.15
Count of all blocks received with uncorrectable errors on this channel within the current 15 minute interval.
OBJECT-TYPE    
  PerfCurrentCount  

sheAdslAtucChanPerfDataCurr15MinNcd 1.3.6.1.4.1.231.7.1.2.1.6.1.1.14.1.16
Count of no cell delineation(ncd) on this channel within the current 15 minute time interval.
OBJECT-TYPE    
  Gauge32  

sheAdslAtucChanPerfDataCurr15MinOcd 1.3.6.1.4.1.231.7.1.2.1.6.1.1.14.1.17
Count of out of cell delineation (ocd) on this channel within the current 15 minute time interval.
OBJECT-TYPE    
  Gauge32  

sheAdslAtucChanPerfDataCurr15MinHec 1.3.6.1.4.1.231.7.1.2.1.6.1.1.14.1.18
Header error check counter(hec) on this channel within the current 15 minute time interval.
OBJECT-TYPE    
  Gauge32  

sheAdslAtucChanPerfDataCurr1DayTimeElapsed 1.3.6.1.4.1.231.7.1.2.1.6.1.1.14.1.19
Number of seconds that have elapsed since the beginning of the current 1-day interval.
OBJECT-TYPE    
  AdslPerfTimeElapsed 0..86399  

sheAdslAtucChanPerfDataCurr1DayReceivedBlks 1.3.6.1.4.1.231.7.1.2.1.6.1.1.14.1.20
Count of all encoded blocks received on this channel during the current day as measured by adslAtucChanPerfCurr1DayTimeElapsed.
OBJECT-TYPE    
  AdslPerfCurrDayCount  

sheAdslAtucChanPerfDataCurr1DayTransmittedBlks 1.3.6.1.4.1.231.7.1.2.1.6.1.1.14.1.21
Count of all encoded blocks transmitted on this channel during the current day as measured by adslAtucChanPerfCurr1DayTimeElapsed.
OBJECT-TYPE    
  AdslPerfCurrDayCount  

sheAdslAtucChanPerfDataCurr1DayCorrectedBlks 1.3.6.1.4.1.231.7.1.2.1.6.1.1.14.1.22
Count of all blocks received with errors that were corrected on this channel during the current day as measured by adslAtucChanPerfCurr1DayTimeElapsed.
OBJECT-TYPE    
  AdslPerfCurrDayCount  

sheAdslAtucChanPerfDataCurr1DayUncorrectBlks 1.3.6.1.4.1.231.7.1.2.1.6.1.1.14.1.23
Count of all blocks received with uncorrectable errors on this channel during the current day as measured by adslAtucChanPerfCurr1DayTimeElapsed.
OBJECT-TYPE    
  AdslPerfCurrDayCount  

sheAdslAtucChanPerfDataCurr1DayNcd 1.3.6.1.4.1.231.7.1.2.1.6.1.1.14.1.24
Count of no cell delineation (ncd) on this channel within the current 1 day time interval.
OBJECT-TYPE    
  Gauge32  

sheAdslAtucChanPerfDataCurr1DayOcd 1.3.6.1.4.1.231.7.1.2.1.6.1.1.14.1.25
Count of out of cell delineation (ocd) on this channel within the current 1 day time interval.
OBJECT-TYPE    
  Gauge32  

sheAdslAtucChanPerfDataCurr1DayHec 1.3.6.1.4.1.231.7.1.2.1.6.1.1.14.1.26
Header error check counter (hec) on this channel within the current 1 day time interval.
OBJECT-TYPE    
  Gauge32  

sheAdslAtucChanPerfDataPrev1DayMoniSecs 1.3.6.1.4.1.231.7.1.2.1.6.1.1.14.1.27
The amount of time in the previous 1-day interval over which the performance monitoring information is actually counted. This value will be the same as the interval duration except in a situation where performance monitoring data could not be collected for any reason.
OBJECT-TYPE    
  INTEGER 0..86400  

sheAdslAtucChanPerfDataPrev1DayReceivedBlks 1.3.6.1.4.1.231.7.1.2.1.6.1.1.14.1.28
Count of all encoded blocks received on this channel within the most recent previous 1-day period.
OBJECT-TYPE    
  AdslPerfPrevDayCount  

sheAdslAtucChanPerfDataPrev1DayTransmittedBlks 1.3.6.1.4.1.231.7.1.2.1.6.1.1.14.1.29
Count of all encoded blocks transmitted on this channel within the most recent previous 1-day period.
OBJECT-TYPE    
  AdslPerfPrevDayCount  

sheAdslAtucChanPerfDataPrev1DayCorrectedBlks 1.3.6.1.4.1.231.7.1.2.1.6.1.1.14.1.30
Count of all blocks received with errors that were corrected on this channel within the most recent previous 1-day period.
OBJECT-TYPE    
  AdslPerfPrevDayCount  

sheAdslAtucChanPerfDataPrev1DayUncorrectBlks 1.3.6.1.4.1.231.7.1.2.1.6.1.1.14.1.31
Count of all blocks received with uncorrectable errors on this channel within the most recent previous 1-day period.
OBJECT-TYPE    
  AdslPerfPrevDayCount  

sheAdslAtucChanPerfDataPrev1DayNcd 1.3.6.1.4.1.231.7.1.2.1.6.1.1.14.1.32
Count of no cell delineation (ncd) on this channel within the most recent previous 1-day period.
OBJECT-TYPE    
  Gauge32  

sheAdslAtucChanPerfDataPrev1DayOcd 1.3.6.1.4.1.231.7.1.2.1.6.1.1.14.1.33
Count of out of cell delineation (ocd) on this channel within the most recent previous 1-day period.
OBJECT-TYPE    
  Gauge32  

sheAdslAtucChanPerfDataPrev1DayHec 1.3.6.1.4.1.231.7.1.2.1.6.1.1.14.1.34
Header error check counter(hec) on this channel within the most recent previous 1-day period.
OBJECT-TYPE    
  Gauge32  

sheAdslAtucChanIntervalTable 1.3.6.1.4.1.231.7.1.2.1.6.1.1.15
This table provides one row for each ATUC channel's performance data collection interval.
OBJECT-TYPE    
  SEQUENCE OF  
    SheAdslAtucChanIntervalEntry

sheAdslAtucChanIntervalEntry 1.3.6.1.4.1.231.7.1.2.1.6.1.1.15.1
An entry in the adslAtucIntervalTable. This table is only supported by NE releases smaller then R2.5 (NO dualLatency support)!!
OBJECT-TYPE    
  SheAdslAtucChanIntervalEntry  

sheAdslAtucChanIntervalNumber 1.3.6.1.4.1.231.7.1.2.1.6.1.1.15.1.1
Performance Data Interval number 1 is the the most recent previous interval; interval 96 is 24 hours ago. Intervals 2..96 are optional.
OBJECT-TYPE    
  INTEGER 1..96  

sheAdslAtucChanIntervalValidData 1.3.6.1.4.1.231.7.1.2.1.6.1.1.15.1.2
This variable indicates if the data for this interval is valid.
OBJECT-TYPE    
  TruthValue  

sheAdslAtucChanIntervalEndTime 1.3.6.1.4.1.231.7.1.2.1.6.1.1.15.1.3
This variable indicates the time of storing this interval.
OBJECT-TYPE    
  Unsigned32  

sheAdslAtucChanIntervalReceivedBlks 1.3.6.1.4.1.231.7.1.2.1.6.1.1.15.1.4
Count of all encoded blocks received on this channel during this interval.
OBJECT-TYPE    
  PerfIntervalCount  

sheAdslAtucChanIntervalTransmittedBlks 1.3.6.1.4.1.231.7.1.2.1.6.1.1.15.1.5
Count of all encoded blocks transmitted on this channel during this interval.
OBJECT-TYPE    
  PerfIntervalCount  

sheAdslAtucChanIntervalCorrectedBlks 1.3.6.1.4.1.231.7.1.2.1.6.1.1.15.1.6
Count of all blocks received with errors that were corrected on this channel during this interval.
OBJECT-TYPE    
  PerfIntervalCount  

sheAdslAtucChanIntervalUncorrectBlks 1.3.6.1.4.1.231.7.1.2.1.6.1.1.15.1.7
Count of all blocks received with uncorrectable errors on this channel during this interval.
OBJECT-TYPE    
  PerfIntervalCount  

sheAdslAtucChanIntervalNcd 1.3.6.1.4.1.231.7.1.2.1.6.1.1.15.1.8
Indicates count of no cell delineation on this channel for this interval.
OBJECT-TYPE    
  Counter32  

sheAdslAtucChanIntervalOcd 1.3.6.1.4.1.231.7.1.2.1.6.1.1.15.1.9
Indicates count of out cell delineation on this channel for this interval.
OBJECT-TYPE    
  Counter32  

sheAdslAtucChanIntervalHec 1.3.6.1.4.1.231.7.1.2.1.6.1.1.15.1.10
Indicates Header error check counter on this channel during this interval.
OBJECT-TYPE    
  Counter32  

sheAdslAturPhysTable 1.3.6.1.4.1.231.7.1.2.1.6.1.1.16
This table provides one row for each ATUR Each row contains the Physical Layer Parameters table for that ATUR. ADSL physical interfaces are those ifEntries where ifType is equal to adsl(94).
OBJECT-TYPE    
  SEQUENCE OF  
    SheAdslAturPhysEntry

sheAdslAturPhysEntry 1.3.6.1.4.1.231.7.1.2.1.6.1.1.16.1
An entry in the adslAturPhysTable.
OBJECT-TYPE    
  SheAdslAturPhysEntry  

sheAdslAturPhysInvSerialNumber 1.3.6.1.4.1.231.7.1.2.1.6.1.1.16.1.1
The vendor specific string that identifies the vendor equipment.
OBJECT-TYPE    
  SnmpAdminString Size(0..32)  

sheAdslAturPhysInvVendorID 1.3.6.1.4.1.231.7.1.2.1.6.1.1.16.1.2
The vendor ID code is a copy of the binary vendor identification field defined by the PHY[10] and expressed as readable characters.
OBJECT-TYPE    
  SnmpAdminString Size(0..16)  

sheAdslAturPhysInvVersionNumber 1.3.6.1.4.1.231.7.1.2.1.6.1.1.16.1.3
The vendor specific version number sent by this ATU as part of the initialization messages. It is a copy of the binary version number field defined by the PHY[10] and expressed as readable characters.
OBJECT-TYPE    
  SnmpAdminString Size(0..16)  

sheAdslAturPhysCurrSnrMgn 1.3.6.1.4.1.231.7.1.2.1.6.1.1.16.1.4
Noise Margin as seen by this ATU with respect to its received signal in tenth dB.
OBJECT-TYPE    
  INTEGER -640..640  

sheAdslAturPhysCurrAtn 1.3.6.1.4.1.231.7.1.2.1.6.1.1.16.1.5
Measured difference in the total power transmitted by the peer ATU and the total power received by this ATU.
OBJECT-TYPE    
  Gauge32 0..630  

sheAdslAturPhysCurrStatus 1.3.6.1.4.1.231.7.1.2.1.6.1.1.16.1.6
Indicates current state of the ATUR line. This is a bit-map of possible conditions. Due to the isolation of the ATUR when line problems occur, many state conditions like loss of power, loss of quality signal, and initialization errors, can not be determined. While trouble shooting ATUR, also use object, adslAtucCurrStatus. The various bit positions are: 0 noDefect There no defects on the line 1 lossOfFraming ATUR failure due to not receiving valid frame 2 lossOfSignal ATUR failure due to not receiving signal 3 lossOfPower ATUR failure due to loss of power 4 lossOfSignalQuality Loss of Signal Quality is declared when the Noise Margin falls below the Minimum Noise Margin, or the bit-error-rate exceeds 10^-7. This is intended to supplement ifOperStatus.
OBJECT-TYPE    
  SheAdslLineCurrentStatusType  

sheAdslAturPhysCurrOutputPwr 1.3.6.1.4.1.231.7.1.2.1.6.1.1.16.1.7
Measured total output power transmitted by this ATU. This is the measurement that was reported during the last activation sequence.
OBJECT-TYPE    
  INTEGER -310..310  

sheAdslAturPhysCurrAttainableRate 1.3.6.1.4.1.231.7.1.2.1.6.1.1.16.1.8
Indicates the maximum currently attainable data rate by the ATU. This value will be equal or greater than the current line rate.
OBJECT-TYPE    
  Gauge32  

sheAdslAturPhysConfig 1.3.6.1.4.1.231.7.1.2.1.6.1.1.16.1.9
This object provides the upstream and downstream ATU-R configuration data (EOC - read 5 sec after data mode).
OBJECT-TYPE    
  OCTET STRING Size(0..255)  

sheAdslAturPhysDeltHLINSCds 1.3.6.1.4.1.231.7.1.2.1.6.1.1.16.1.10
DELT-related parameter that provides the scale factor to be applied to the downstream Hlin(f) values. (Not available for ADSL but ADSL2 & ADSL2plus).
OBJECT-TYPE    
  Unsigned32  

sheAdslAturPhysDeltHLINpsds 1.3.6.1.4.1.231.7.1.2.1.6.1.1.16.1.11
DELT-related parameter that provides an array of complex downstream Hlin(f) values in linear scale. Every two octects refer to one element in this array of octets. (Not available for ADSL but ADSL2 & ADSL2plus). This parameter is an array of complex downstream Hlin(f) values in linear scale. Each array entry represents the Hlin(f = i*HLINGds* delta(f)) value for a particular subcarrier group index i, ranging from 0 to MIN(NSCds - 1,511). The Hlin(f) is represented as ((scale/2(exp15))*((a(i) + j*b(i))/2(exp15))), with scale being coded as a 16-bit unsigned integer and, a(i) and b(i) coded as 16-bit 2s complement signed integers in the (-2(exp15) + 1) to (+2(exp15) - 1) range. A special value a(i) = b(i) = -2(exp15) indicates that no measurement could be done for this subcarrier group because it is out of the passband or that the attenuation is out of range to be represented. This parameter is only available after a loop diagnostic procedure.
OBJECT-TYPE    
  OCTET STRING Size(0..2048)  

sheAdslAturPhysDeltHLOGMTds 1.3.6.1.4.1.231.7.1.2.1.6.1.1.16.1.12
DELT-related parameter that provides the number of symbols used to measure the downstream Hlog(f). (Not available for ADSL but ADSL2 & ADSL2plus).
OBJECT-TYPE    
  Unsigned32  

sheAdslAturPhysDeltHLOGpsds 1.3.6.1.4.1.231.7.1.2.1.6.1.1.16.1.13
DELT-related parameter that provides an array of real downstream Hlog(f) values in dB. (Not available for ADSL but ADSL2 & ADSL2plus). This parameter is an array of real downstream Hlog(f) values in dB. Each array entry represents the real Hlog(f = i*HLOGGds* delta(f)) value for a particular subcarrier group sub-carrier index i, ranging from 0 to MIN(NSCds - 1,511). The real Hlog(f) value is represented as (6 - m(i)/10), with m(i) 10-bit unsigned integer in the 0 to 1022 range. A special value m = 1023 indicates that no measurement could be done for this subcarrier group because it is out of the passband or that the attenuation is out of range to be represented.
OBJECT-TYPE    
  OCTET STRING Size(0..1024)  

sheAdslAturPhysDeltQLNMTds 1.3.6.1.4.1.231.7.1.2.1.6.1.1.16.1.14
DELT-related parameter that provides the number of symbols used to measure the downstream QLN(f) values. (Not available for ADSL but ADSL2 & ADSL2plus).
OBJECT-TYPE    
  Unsigned32  

sheAdslAturPhysDeltQLNpsds 1.3.6.1.4.1.231.7.1.2.1.6.1.1.16.1.15
DELT-related parameter that provides an array of real downstream QLN(f) values in dBm/Hz. Every two octects refer to one element in this array of octets. (Not available for ADSL but ADSL2 & ADSL2plus). This parameter is an array of real downstream QLN(f) values in dBm/Hz. Each array entry represents the QLN(f = i*QLNGds* delta(f)) value for a particular subcarrier group index i, ranging from 0 to MIN(NSCds - 1,511). The QLN(f) is represented as (-23 - n(i)/2), with n(i) an 8-bit unsigned integer in the 0 to 254 range. A special value n(i) = 255 indicates that no measurement could be done for this subcarrier group because it is out of the passband or that the noise PSD is out of range to be represented.
OBJECT-TYPE    
  OCTET STRING Size(0..512)  

sheAdslAturPhysCurrentBinBitLoading 1.3.6.1.4.1.231.7.1.2.1.6.1.1.16.1.16
This parameter represent the current used bit loading per bin in downstream direction. Each octet map to the corresponding bin.
OBJECT-TYPE    
  OCTET STRING Size(0..512)  

sheAdslAturPhysDeltSNRMTds 1.3.6.1.4.1.231.7.1.2.1.6.1.1.16.1.17
DELT-related parameter that provides the number of symbols used to measure the downstream SNR(f) values. (Not available for ADSL and ADSL2plus) It is represented as a 16-bit unsigned value. After a loop diagnostic procedure, this parameter shall contain the number of symbols used to generate the associate parameter. It should correspond to the value specified in the Recommendation (e.g., the number of symbols in 1 s time interval for G.992.3).
OBJECT-TYPE    
  Unsigned32  

sheAdslAturPhysDeltDMTBinSNRds 1.3.6.1.4.1.231.7.1.2.1.6.1.1.16.1.18
DELT-related parameter that provides an array of real downstream SNR(f) values in dB (Not available for ADSL and ADSL2plus) Each array entry represents the SNR(f = i*f) value for a particular subcarrier index i, ranging from 0 to NSCds C 1. The SNR(f) is represented as (C32 + snr(i)/2), with snr(i) an 8-bit unsigned integer in the 0 to 254 range. A special value snr(i) = 255 indicates that no measurement could be done for the subcarrier because it is out of the passband or that the noise PSD is out of range to be represented.
OBJECT-TYPE    
  OCTET STRING Size(0..512)  

sheAdslAturPhysDeltLastTxState 1.3.6.1.4.1.231.7.1.2.1.6.1.1.16.1.19
DELT-related parameter that provides last successful transmitted initialization state by the ATU-R. (Not available for ADSL and ADSL2plus) Initialization states are defined in the individual ADSL Recommendations and are counted from 0 (if G.994.1 is used) or 1 (if G.994.1 is not used) up to Showtime. This parameter must be interpreted along with the ADSL Transmission System. This parameter is available only when, after a failed full initialization, the line diagnostics procedures are activated on the line. Line diagnostics procedures can be activated by the operator of the system (through the Line State Forced line configuration parameter) or autonomously by the ATU-C or ATU-R.
OBJECT-TYPE    
  SheAdslPhysAturDeltLastTxStateType  

sheAdslAturPhysDeltSATNds 1.3.6.1.4.1.231.7.1.2.1.6.1.1.16.1.20
DELT-related parameter that provides the downtream signal attenuation (length = 4 bytes). (Not available for ADSL and ADSL2plus). This parameter is the measured difference in the total power transmitted by the ATU-C and the total power received by the ATU-R over all subcarriers during showtime. The downstream line attenuation ranges from 0 to +127 dB with 0.1 dB steps. A special value indicates the line attenuation is out of range to be represented. NOTE: During showtime, only a subset of the subcarriers may be transmitted by the ATU-C, as compared to diagnostics mode and initialization. Therefore, the downstream Signal attenuation may be significantly lower than the downstream Line attenuation.
OBJECT-TYPE    
  Unsigned32 0..1270  

sheAdslAturChanTable 1.3.6.1.4.1.231.7.1.2.1.6.1.1.17
This table provides one row for each ATUR channel.
OBJECT-TYPE    
  SEQUENCE OF  
    SheAdslAturChanEntry

sheAdslAturChanEntry 1.3.6.1.4.1.231.7.1.2.1.6.1.1.17.1
An entry in the adslAturChanTable. This table is only supported by NE releases smaller then R2.5 (NO dualLatency support)!!
OBJECT-TYPE    
  SheAdslAturChanEntry  

sheAdslAturChanInterleaveDelay 1.3.6.1.4.1.231.7.1.2.1.6.1.1.17.1.1
Interleave Delay for this channel. Interleave delay applies only to the interleave channel and defines the mapping (relative spacing) between subsequent input bytes at the interleaver input and their placement in the bit stream at the interleaver output. Larger numbers provide greater separation between consecutive input bytes in the output bit stream allowing for improved impulse noise immunity at the expense of payload latency. In the case where the ifType is Fast(125), use noSuchObject.
OBJECT-TYPE    
  Gauge32  

sheAdslAturChanCurrTxRate 1.3.6.1.4.1.231.7.1.2.1.6.1.1.17.1.2
Actual transmit rate on this channel.
OBJECT-TYPE    
  Gauge32 1..32736  

sheAdslAturChanPrevTxRate 1.3.6.1.4.1.231.7.1.2.1.6.1.1.17.1.3
The rate at the time of the last adslAturRateChangeTrap event. It is also set at initialization to prevent a trap being sent. Rate changes less than adslAturThresh(*)RateDown or less than adslAturThresh(*)RateUp will not cause a trap or cause this object to change. (*) == Fast or Interleave. See AdslLineAlarmConfProfileEntry.
OBJECT-TYPE    
  Gauge32 1..32736  

sheAdslAturChanCrcBlockLength 1.3.6.1.4.1.231.7.1.2.1.6.1.1.17.1.4
Indicates the length of the channel data-block on which the CRC operates. Refer to Line Code Specific MIBs, [11] and [12] for more information.
OBJECT-TYPE    
  Gauge32  

sheAdslAturChanCurrAtmStatus 1.3.6.1.4.1.231.7.1.2.1.6.1.1.17.1.5
This object indicates an ncd or lcd failure if the counter surpasses 127. If neither ATM counter surpasses 127, the return value will be NoAtmDefect. noAtmDefect(0), noCellDeleniation(1), lossOfCellDeleniation(2)
OBJECT-TYPE    
  SheAdslLineAtmStatus  

sheAdslAturChanRsSymbols 1.3.6.1.4.1.231.7.1.2.1.6.1.1.17.1.6
This object indicates number of DMT symbols per Reed- Solomon code word (S) in the upstream direction Note that S is not restricted to interleaved mode only. Even in fast mode, S is a valid constant value and is equal to 1.
OBJECT-TYPE    
  Unsigned32  

sheAdslAturChanRsDepth 1.3.6.1.4.1.231.7.1.2.1.6.1.1.17.1.7
This object indicates interleaving depth (D) in the upstream direction Note that D is not restricted to interleaved mode only. Even in fast mode, D is a valid constant value and is equal to 1.
OBJECT-TYPE    
  Unsigned32  

sheAdslAturChanRsRedundancy 1.3.6.1.4.1.231.7.1.2.1.6.1.1.17.1.8
This object indicates number of redundant bytes (R) per Reed-Solomon code in the upstream direction.
OBJECT-TYPE    
  Unsigned32  

sheAdslAturPerfDataTable 1.3.6.1.4.1.231.7.1.2.1.6.1.1.18
This table provides one row for each ATUR. ADSL physical interfaces are those ifEntries where ifType is equal to adsl(94).
OBJECT-TYPE    
  SEQUENCE OF  
    SheAdslAturPerfDataEntry

sheAdslAturPerfDataEntry 1.3.6.1.4.1.231.7.1.2.1.6.1.1.18.1
An entry in adslAturPerfDataTable.
OBJECT-TYPE    
  SheAdslAturPerfDataEntry  

sheAdslAturPerfDataLofs 1.3.6.1.4.1.231.7.1.2.1.6.1.1.18.1.1
Count of the number of Loss of Framing failures since agent reset.
OBJECT-TYPE    
  Counter32  

sheAdslAturPerfDataLoss 1.3.6.1.4.1.231.7.1.2.1.6.1.1.18.1.2
Count of the number of Loss of Signal failures since agent reset.
OBJECT-TYPE    
  Counter32  

sheAdslAturPerfDataLprs 1.3.6.1.4.1.231.7.1.2.1.6.1.1.18.1.3
Count of the number of Loss of Power failures since agent reset.
OBJECT-TYPE    
  Counter32  

sheAdslAturPerfDataESs 1.3.6.1.4.1.231.7.1.2.1.6.1.1.18.1.4
Count of the number of Errored Seconds since agent reset. The errored second parameter is a count of one-second intervals containing one or more crc anomalies, or one or more los or sef defects.
OBJECT-TYPE    
  Counter32  

sheAdslAturPerfDataStatSesL 1.3.6.1.4.1.231.7.1.2.1.6.1.1.18.1.5
The value of this object reports the count of severely errored second-line since the last agent reset.
OBJECT-TYPE    
  Counter32  

sheAdslAturPerfDataStatUasL 1.3.6.1.4.1.231.7.1.2.1.6.1.1.18.1.6
The value of this object reports the count of unavailable seconds-line since the last agent reset.
OBJECT-TYPE    
  Counter32  

sheAdslAturPerfDataValidIntervals 1.3.6.1.4.1.231.7.1.2.1.6.1.1.18.1.7
The number of previous 15-minute intervals in the interval table for which data was collected. Given that is the maximum # of intervals supported. The value will be unless the measurement was (re-)started within the last (*15) minutes, in which case the value will be the number of complete 15 minute intervals for which the agent has at least some data. In certain cases (e.g., in the case where the agent is a proxy) it is possible that some intervals are unavailable. In this case, this interval is the maximum interval number for which data is available.
OBJECT-TYPE    
  INTEGER 0..96  

sheAdslAturPerfDataInvalidIntervals 1.3.6.1.4.1.231.7.1.2.1.6.1.1.18.1.8
The number of intervals in the range from 0 to the value of adslAturPerfValidIntervals for which no data is available. This object will typically be zero except in cases where the data for some intervals are not available (e.g., in proxy situations).
OBJECT-TYPE    
  INTEGER 0..96  

sheAdslAturPerfDataCurr15MinTimeElapsed 1.3.6.1.4.1.231.7.1.2.1.6.1.1.18.1.9
Total elapsed seconds in this interval.
OBJECT-TYPE    
  AdslPerfTimeElapsed 0..899  

sheAdslAturPerfDataCurr15MinLofs 1.3.6.1.4.1.231.7.1.2.1.6.1.1.18.1.10
Count of seconds in the current 15 minute interval when there was Loss of Framing.
OBJECT-TYPE    
  PerfCurrentCount  

sheAdslAturPerfDataCurr15MinLoss 1.3.6.1.4.1.231.7.1.2.1.6.1.1.18.1.11
Count of seconds in the current 15 minute interval when there was Loss of Signal.
OBJECT-TYPE    
  PerfCurrentCount  

sheAdslAturPerfDataCurr15MinLprs 1.3.6.1.4.1.231.7.1.2.1.6.1.1.18.1.12
Count of seconds in the current 15 minute interval when there was Loss of Power.
OBJECT-TYPE    
  PerfCurrentCount  

sheAdslAturPerfDataCurr15MinESs 1.3.6.1.4.1.231.7.1.2.1.6.1.1.18.1.13
Count of Errored Seconds in the current 15 minute interval. The errored second parameter is a count of one-second intervals containing one or more crc anomalies, or one or more los or sef defects.
OBJECT-TYPE    
  PerfCurrentCount  

sheAdslAturPerfDataCurr15MinSesL 1.3.6.1.4.1.231.7.1.2.1.6.1.1.18.1.14
For the current 15-minute interval, adslAturPerfCurr15MinSesL reports the current number of seconds during which there have been severely errored seconds-line.
OBJECT-TYPE    
  PerfCurrentCount  

sheAdslAturPerfDataCurr15MinUasL 1.3.6.1.4.1.231.7.1.2.1.6.1.1.18.1.15
For the current 15-minute interval, adslAturPerfCurr15MinUasL reports the current number of seconds during which there have been available seconds-line.
OBJECT-TYPE    
  PerfCurrentCount  

sheAdslAturPerfDataCurr1DayTimeElapsed 1.3.6.1.4.1.231.7.1.2.1.6.1.1.18.1.16
Number of seconds that have elapsed since the beginning of the current 1-day interval.
OBJECT-TYPE    
  AdslPerfTimeElapsed 0..86399  

sheAdslAturPerfDataCurr1DayLofs 1.3.6.1.4.1.231.7.1.2.1.6.1.1.18.1.17
Count of the number of seconds when there was Loss of Framing during the current day as measured by adslAturPerfCurr1DayTimeElapsed.
OBJECT-TYPE    
  AdslPerfCurrDayCount  

sheAdslAturPerfDataCurr1DayLoss 1.3.6.1.4.1.231.7.1.2.1.6.1.1.18.1.18
Count of the number of seconds when there was Loss of Signal during the current day as measured by adslAturPerfCurr1DayTimeElapsed.
OBJECT-TYPE    
  AdslPerfCurrDayCount  

sheAdslAturPerfDataCurr1DayLprs 1.3.6.1.4.1.231.7.1.2.1.6.1.1.18.1.19
Count of the number of seconds when there was Loss of Power during the current day as measured by adslAturPerfCurr1DayTimeElapsed.
OBJECT-TYPE    
  AdslPerfCurrDayCount  

sheAdslAturPerfDataCurr1DayESs 1.3.6.1.4.1.231.7.1.2.1.6.1.1.18.1.20
Count of Errored Seconds during the current day as measured by adslAturPerfCurr1DayTimeElapsed. The errored second parameter is a count of one-second intervals containing one or more crc anomalies, or one or more los or sef defects.
OBJECT-TYPE    
  AdslPerfCurrDayCount  

sheAdslAturPerfDataCurr1DaySesL 1.3.6.1.4.1.231.7.1.2.1.6.1.1.18.1.21
For the current day as measured by adslAturPerfCurr1DayTimeElapsed [RFC2662], adslAturPerfCurr1DaySesL reports the number of seconds during which there have been severely errored seconds-line.
OBJECT-TYPE    
  AdslPerfCurrDayCount  

sheAdslAturPerfDataCurr1DayUasL 1.3.6.1.4.1.231.7.1.2.1.6.1.1.18.1.22
For the current day as measured by adslAturPerfCurr1DayTimeElapsed [RFC2662], adslAturPerfCurr1DayUasL reports the number of seconds during which there have been unavailable seconds-line.
OBJECT-TYPE    
  AdslPerfCurrDayCount  

sheAdslAturPerfDataPrev1DayMoniSecs 1.3.6.1.4.1.231.7.1.2.1.6.1.1.18.1.23
The amount of time in the previous 1-day interval over which the performance monitoring information is actually counted. This value will be the same as the interval duration except in a situation where performance monitoring data could not be collected for any reason.
OBJECT-TYPE    
  INTEGER 0..86400  

sheAdslAturPerfDataPrev1DayLofs 1.3.6.1.4.1.231.7.1.2.1.6.1.1.18.1.24
Count of seconds in the interval when there was Loss of Framing within the most recent previous 1-day period.
OBJECT-TYPE    
  AdslPerfPrevDayCount  

sheAdslAturPerfDataPrev1DayLoss 1.3.6.1.4.1.231.7.1.2.1.6.1.1.18.1.25
Count of seconds in the interval when there was Loss of Signal within the most recent previous 1-day period.
OBJECT-TYPE    
  AdslPerfPrevDayCount  

sheAdslAturPerfDataPrev1DayLprs 1.3.6.1.4.1.231.7.1.2.1.6.1.1.18.1.26
Count of seconds in the interval when there was Loss of Power within the most recent previous 1-day period.
OBJECT-TYPE    
  AdslPerfPrevDayCount  

sheAdslAturPerfDataPrev1DayESs 1.3.6.1.4.1.231.7.1.2.1.6.1.1.18.1.27
Count of Errored Seconds within the most recent previous 1-day period. The errored second parameter is a count of one-second intervals containing one or more crc anomalies, or one or more los or sef defects.
OBJECT-TYPE    
  AdslPerfPrevDayCount  

sheAdslAturPerfDataPrev1DaySesL 1.3.6.1.4.1.231.7.1.2.1.6.1.1.18.1.28
For the previous day, adslAturPerfPrev1DaySesL reports the number of seconds during which there were severely errored seconds-line.
OBJECT-TYPE    
  AdslPerfPrevDayCount  

sheAdslAturPerfDataPrev1DayUasL 1.3.6.1.4.1.231.7.1.2.1.6.1.1.18.1.29
For the previous day, adslAturPerfPrev1DayUasL reports the number of seconds during which there were severely errored seconds-line.
OBJECT-TYPE    
  AdslPerfPrevDayCount  

sheAdslAturIntervalTable 1.3.6.1.4.1.231.7.1.2.1.6.1.1.19
This table provides one row for each ATUR performance data collection interval. ADSL physical interfaces are those ifEntries where ifType is equal to adsl(94).
OBJECT-TYPE    
  SEQUENCE OF  
    SheAdslAturIntervalEntry

sheAdslAturIntervalEntry 1.3.6.1.4.1.231.7.1.2.1.6.1.1.19.1
An entry in the adslAturIntervalTable.
OBJECT-TYPE    
  SheAdslAturIntervalEntry  

sheAdslAturIntervalNumber 1.3.6.1.4.1.231.7.1.2.1.6.1.1.19.1.1
Performance Data Interval number 1 is the the most recent previous interval; interval 96 is 24 hours ago. Intervals 2..96 are optional.
OBJECT-TYPE    
  INTEGER 1..96  

sheAdslAturIntervalValidData 1.3.6.1.4.1.231.7.1.2.1.6.1.1.19.1.2
This variable indicates if the data for this interval is valid.
OBJECT-TYPE    
  TruthValue  

sheAdslAturIntervalEndTime 1.3.6.1.4.1.231.7.1.2.1.6.1.1.19.1.3
This variable indicates the time of storing this interval.
OBJECT-TYPE    
  Unsigned32  

sheAdslAturIntervalLofs 1.3.6.1.4.1.231.7.1.2.1.6.1.1.19.1.4
Count of seconds in the interval when there was Loss of Framing.
OBJECT-TYPE    
  PerfIntervalCount  

sheAdslAturIntervalLoss 1.3.6.1.4.1.231.7.1.2.1.6.1.1.19.1.5
Count of seconds in the interval when there was Loss of Signal.
OBJECT-TYPE    
  PerfIntervalCount  

sheAdslAturIntervalLprs 1.3.6.1.4.1.231.7.1.2.1.6.1.1.19.1.6
Count of seconds in the interval when there was Loss of Power.
OBJECT-TYPE    
  PerfIntervalCount  

sheAdslAturIntervalESs 1.3.6.1.4.1.231.7.1.2.1.6.1.1.19.1.7
Count of Errored Seconds in the interval. The errored second parameter is a count of one-second intervals containing one or more crc anomalies, or one or more los or sef defects.
OBJECT-TYPE    
  PerfIntervalCount  

sheAdslAturIntervalSesL 1.3.6.1.4.1.231.7.1.2.1.6.1.1.19.1.8
For the each interval, adslAturIntervalSesL reports the number of seconds during which there have been severely errored seconds-line.
OBJECT-TYPE    
  PerfIntervalCount  

sheAdslAturIntervalUasL 1.3.6.1.4.1.231.7.1.2.1.6.1.1.19.1.9
For the each interval, adslAturIntervalUasL reports the number of seconds during which there have been unavailable seconds-line.
OBJECT-TYPE    
  PerfIntervalCount  

sheAdslAturChanPerfDataTable 1.3.6.1.4.1.231.7.1.2.1.6.1.1.20
This table provides one row for each ATUR channel.
OBJECT-TYPE    
  SEQUENCE OF  
    SheAdslAturChanPerfDataEntry

sheAdslAturChanPerfDataEntry 1.3.6.1.4.1.231.7.1.2.1.6.1.1.20.1
An entry in adslAturChanPerfDataTable. This table is only supported by NE releases smaller then R2.5 (NO dualLatency support)!!
OBJECT-TYPE    
  SheAdslAturChanPerfDataEntry  

sheAdslAturChanPerfDataReceivedBlks 1.3.6.1.4.1.231.7.1.2.1.6.1.1.20.1.1
Count of all encoded blocks received on this channel since agent reset.
OBJECT-TYPE    
  Counter32  

sheAdslAturChanPerfDataTransmittedBlks 1.3.6.1.4.1.231.7.1.2.1.6.1.1.20.1.2
Count of all encoded blocks transmitted on this channel since agent reset.
OBJECT-TYPE    
  Counter32  

sheAdslAturChanPerfDataCorrectedBlks 1.3.6.1.4.1.231.7.1.2.1.6.1.1.20.1.3
Count of all blocks received with errors that were corrected since agent reset. These blocks are passed on as good data.
OBJECT-TYPE    
  Counter32  

sheAdslAturChanPerfDataUncorrectBlks 1.3.6.1.4.1.231.7.1.2.1.6.1.1.20.1.4
Count of all blocks received with uncorrectable errors since agent reset.
OBJECT-TYPE    
  Counter32  

sheAdslAturChanPerfDataExtnNcd 1.3.6.1.4.1.231.7.1.2.1.6.1.1.20.1.5
Number of packets with no cell delineation(NCD) error on this channel.
OBJECT-TYPE    
  Gauge32  

sheAdslAturChanPerfDataExtnHec 1.3.6.1.4.1.231.7.1.2.1.6.1.1.20.1.6
Number of packets with Header error check (HEC) error on this channel.
OBJECT-TYPE    
  Gauge32  

sheAdslAturChanPerfDataPerfValidIntervals 1.3.6.1.4.1.231.7.1.2.1.6.1.1.20.1.7
The number of previous 15-minute intervals in the interval table for which data was collected. Given that is the maximum # of intervals supported. The value will be unless the measurement was (re-)started within the last (*15) minutes, in which case the value will be the number of complete 15 minute intervals for which the agent has at least some data. In certain cases (e.g., in the case where the agent is a proxy) it is possible that some intervals are unavailable. In this case, this interval is the maximum interval number for which data is available.
OBJECT-TYPE    
  INTEGER 0..96  

sheAdslAturChanPerfDataPerfInvalidIntervals 1.3.6.1.4.1.231.7.1.2.1.6.1.1.20.1.8
The number of intervals in the range from 0 to the value of adslAturChanPerfValidIntervals for which no data is available. This object will typically be zero except in cases where the data for some intervals are not available (e.g., in proxy situations).
OBJECT-TYPE    
  INTEGER 0..96  

sheAdslAturChanPerfDataCurr15MinTimeElapsed 1.3.6.1.4.1.231.7.1.2.1.6.1.1.20.1.9
Total elapsed seconds in this interval. A full interval is 900 seconds.
OBJECT-TYPE    
  AdslPerfTimeElapsed 0..899  

sheAdslAturChanPerfDataCurr15MinReceivedBlks 1.3.6.1.4.1.231.7.1.2.1.6.1.1.20.1.10
Count of all encoded blocks received on this channel within the current 15 minute interval.
OBJECT-TYPE    
  PerfCurrentCount  

sheAdslAturChanPerfDataCurr15MinTransmittedBlks 1.3.6.1.4.1.231.7.1.2.1.6.1.1.20.1.11
Count of all encoded blocks transmitted on this channel within the current 15 minute interval.
OBJECT-TYPE    
  PerfCurrentCount  

sheAdslAturChanPerfDataCurr15MinCorrectedBlks 1.3.6.1.4.1.231.7.1.2.1.6.1.1.20.1.12
Count of all blocks received with errors that were corrected on this channel within the current 15 minute interval.
OBJECT-TYPE    
  PerfCurrentCount  

sheAdslAturChanPerfDataCurr15MinUncorrectBlks 1.3.6.1.4.1.231.7.1.2.1.6.1.1.20.1.13
Count of all blocks received with uncorrectable errors on this channel within the current 15 minute interval.
OBJECT-TYPE    
  PerfCurrentCount  

sheAdslAturChanPerfDataExtnCurr15MinNcd 1.3.6.1.4.1.231.7.1.2.1.6.1.1.20.1.14
Number of packets with no cell delineation(NCD) error on this channel within the current 15 minute time interval.
OBJECT-TYPE    
  Gauge32  

sheAdslAturChanPerfDataExtnCurr15MinHec 1.3.6.1.4.1.231.7.1.2.1.6.1.1.20.1.15
Number of packets with Header error check (HEC) error on this channel within the current 15 minute time interval.
OBJECT-TYPE    
  Gauge32  

sheAdslAturChanPerfDataCurr1DayTimeElapsed 1.3.6.1.4.1.231.7.1.2.1.6.1.1.20.1.16
Number of seconds that have elapsed since the beginning of the current 1-day interval.
OBJECT-TYPE    
  AdslPerfTimeElapsed 0..86399  

sheAdslAturChanPerfDataCurr1DayReceivedBlks 1.3.6.1.4.1.231.7.1.2.1.6.1.1.20.1.17
Count of all encoded blocks received on this channel during the current day as measured by adslAturChanPerfCurr1DayTimeElapsed.
OBJECT-TYPE    
  AdslPerfCurrDayCount  

sheAdslAturChanPerfDataCurr1DayTransmittedBlks 1.3.6.1.4.1.231.7.1.2.1.6.1.1.20.1.18
Count of all encoded blocks transmitted on this channel during the current day as measured by adslAturChanPerfCurr1DayTimeElapsed.
OBJECT-TYPE    
  AdslPerfCurrDayCount  

sheAdslAturChanPerfDataCurr1DayCorrectedBlks 1.3.6.1.4.1.231.7.1.2.1.6.1.1.20.1.19
Count of all blocks received with errors that were corrected on this channel during the current day as measured by adslAturChanPerfCurr1DayTimeElapsed.
OBJECT-TYPE    
  AdslPerfCurrDayCount  

sheAdslAturChanPerfDataCurr1DayUncorrectBlks 1.3.6.1.4.1.231.7.1.2.1.6.1.1.20.1.20
Count of all blocks received with uncorrectable errors on this channel during the current day as measured by adslAturChanPerfCurr1DayTimeElapsed.
OBJECT-TYPE    
  AdslPerfCurrDayCount  

sheAdslAturChanPerfDataExtnCurr1DayNcd 1.3.6.1.4.1.231.7.1.2.1.6.1.1.20.1.21
Number of packets with no cell delineation (NCD) error on this channel within the current 1 day time interval.
OBJECT-TYPE    
  Gauge32  

sheAdslAturChanPerfDataExtnCurr1DayHec 1.3.6.1.4.1.231.7.1.2.1.6.1.1.20.1.22
Number of packets with Header error check (HEC) error on this channel within the current 1 day time interval.
OBJECT-TYPE    
  Gauge32  

sheAdslAturChanPerfDataPrev1DayMoniSecs 1.3.6.1.4.1.231.7.1.2.1.6.1.1.20.1.23
The amount of time in the previous 1-day interval over which the performance monitoring information is actually counted. This value will be the same as the interval duration except in a situation where performance monitoring data could not be collected for any reason.
OBJECT-TYPE    
  INTEGER 0..86400  

sheAdslAturChanPerfDataPrev1DayReceivedBlks 1.3.6.1.4.1.231.7.1.2.1.6.1.1.20.1.24
Count of all encoded blocks received on this channel within the most recent previous 1-day period.
OBJECT-TYPE    
  AdslPerfPrevDayCount  

sheAdslAturChanPerfDataPrev1DayTransmittedBlks 1.3.6.1.4.1.231.7.1.2.1.6.1.1.20.1.25
Count of all encoded blocks transmitted on this channel within the most recent previous 1-day period.
OBJECT-TYPE    
  AdslPerfPrevDayCount  

sheAdslAturChanPerfDataPrev1DayCorrectedBlks 1.3.6.1.4.1.231.7.1.2.1.6.1.1.20.1.26
Count of all blocks received with errors that were corrected on this channel within the most recent previous 1-day period.
OBJECT-TYPE    
  AdslPerfPrevDayCount  

sheAdslAturChanPerfDataPrev1DayUncorrectBlks 1.3.6.1.4.1.231.7.1.2.1.6.1.1.20.1.27
Count of all blocks received with uncorrectable errors on this channel within the most recent previous 1-day period.
OBJECT-TYPE    
  AdslPerfPrevDayCount  

sheAdslAturChanPerfDataExtnPrev1DayNcd 1.3.6.1.4.1.231.7.1.2.1.6.1.1.20.1.28
Number of packets with no cell delineation (NCD) error on this channel within the most recent previous period.
OBJECT-TYPE    
  Gauge32  

sheAdslAturChanPerfDataExtnPrev1DayHec 1.3.6.1.4.1.231.7.1.2.1.6.1.1.20.1.29
Number of packets with Header error check (HEC) error on this channel within the most recent previous period.
OBJECT-TYPE    
  Gauge32  

sheAdslAturChanIntervalTable 1.3.6.1.4.1.231.7.1.2.1.6.1.1.21
This table provides one row for each ATUR channel's performance data collection interval.
OBJECT-TYPE    
  SEQUENCE OF  
    SheAdslAturChanIntervalEntry

sheAdslAturChanIntervalEntry 1.3.6.1.4.1.231.7.1.2.1.6.1.1.21.1
An entry in the adslAturIntervalTable. This table is only supported by NE releases smaller then R2.5 (NO dualLatency support)!!
OBJECT-TYPE    
  SheAdslAturChanIntervalEntry  

sheAdslAturChanIntervalNumber 1.3.6.1.4.1.231.7.1.2.1.6.1.1.21.1.1
Performance Data Interval number 1 is the the most recent previous interval; interval 96 is 24 hours ago. Intervals 2..96 are optional.
OBJECT-TYPE    
  INTEGER 1..96  

sheAdslAturChanIntervalValidData 1.3.6.1.4.1.231.7.1.2.1.6.1.1.21.1.2
This variable indicates if the data for this interval is valid.
OBJECT-TYPE    
  TruthValue  

sheAdslAturChanIntervalEndTime 1.3.6.1.4.1.231.7.1.2.1.6.1.1.21.1.3
This variable indicates the time of storing this interval.
OBJECT-TYPE    
  Unsigned32  

sheAdslAturChanIntervalReceivedBlks 1.3.6.1.4.1.231.7.1.2.1.6.1.1.21.1.4
Count of all encoded blocks received on this channel during this interval.
OBJECT-TYPE    
  PerfIntervalCount  

sheAdslAturChanIntervalTransmittedBlks 1.3.6.1.4.1.231.7.1.2.1.6.1.1.21.1.5
Count of all encoded blocks transmitted on this channel during this interval.
OBJECT-TYPE    
  PerfIntervalCount  

sheAdslAturChanIntervalCorrectedBlks 1.3.6.1.4.1.231.7.1.2.1.6.1.1.21.1.6
Count of all blocks received with errors that were corrected on this channel during this interval.
OBJECT-TYPE    
  PerfIntervalCount  

sheAdslAturChanIntervalUncorrectBlks 1.3.6.1.4.1.231.7.1.2.1.6.1.1.21.1.7
Count of all blocks received with uncorrectable errors on this channel during this interval.
OBJECT-TYPE    
  PerfIntervalCount  

sheAdslAturChanIntervalNcd 1.3.6.1.4.1.231.7.1.2.1.6.1.1.21.1.8
Indicates count of no cell delineation on this channel for this interval.
OBJECT-TYPE    
  Gauge32  

sheAdslAturChanIntervalHec 1.3.6.1.4.1.231.7.1.2.1.6.1.1.21.1.9
Indicates Header error check counter on this channel during this interval.
OBJECT-TYPE    
  Gauge32  

sheAdslLineAlarmConfProfileTable 1.3.6.1.4.1.231.7.1.2.1.6.1.1.22
This table contains information on the ADSL line configuration. One entry in this table reflects a profile defined by a manager which can be used to configure the modem for a physical line
OBJECT-TYPE    
  SEQUENCE OF  
    SheAdslLineAlarmConfProfileEntry

sheAdslLineAlarmConfProfileEntry 1.3.6.1.4.1.231.7.1.2.1.6.1.1.22.1
Each entry consists of a list of parameters that represents the configuration of an ADSL modem. 'Dynamic' profiles are implemented. A default profile will always exist. This profile's name will be set to `DEFVAL' and its parameters will be set to vendor specific values, unless otherwise specified in this document.
OBJECT-TYPE    
  SheAdslLineAlarmConfProfileEntry  

sheAdslLineAlarmConfProfileIndex 1.3.6.1.4.1.231.7.1.2.1.6.1.1.22.1.1
Tableindex.
OBJECT-TYPE    
  Integer32 1..65535  

sheAdslLineAlarmConfProfileName 1.3.6.1.4.1.231.7.1.2.1.6.1.1.22.1.2
This object is used by the line alarm configuration table in order to identify a row of this table. Dynamic profiles are implemented. The profile name is user specified. The system will always provide a default profile whose name is `DEFVAL'. This characters are not allowed: space : ? leading numbers
OBJECT-TYPE    
  SnmpAdminString Size(1..32)  

sheAdslLineAlarmConfProfileOpStateTrapEnable 1.3.6.1.4.1.231.7.1.2.1.6.1.1.22.1.3
Enables and disables the OpStateChangeTrap.
OBJECT-TYPE    
  TruthValue  

sheAdslLineAlarmConfProfileAtucThreshFastRateUp 1.3.6.1.4.1.231.7.1.2.1.6.1.1.22.1.4
Applies to `Fast' channels only. Configured change in rate causing an adslAtucRateChangeTrap. A trap is produced when: ChanCurrTxRate >= ChanPrevTxRate plus the value of this object. A value of `0' will disable the trap.
OBJECT-TYPE    
  Unsigned32 0..65535  

sheAdslLineAlarmConfProfileAtucThreshInterleaveRateUp 1.3.6.1.4.1.231.7.1.2.1.6.1.1.22.1.5
Applies to `Interleave' channels only. Configured change in rate causing an adslAtucRateChangeTrap. A trap is produced when: ChanCurrTxRate >= ChanPrevTxRate plus the value of this object. A value of `0' will disable the trap.
OBJECT-TYPE    
  Unsigned32 0..65535  

sheAdslLineAlarmConfProfileAtucThreshFastRateDown 1.3.6.1.4.1.231.7.1.2.1.6.1.1.22.1.6
Applies to `Fast' channels only. Configured change in rate causing an adslAtucRateChangeTrap. A trap is produced when: ChanCurrTxRate <= ChanPrevTxRate minus the value of this object. A value of `0' will disable the trap.
OBJECT-TYPE    
  Unsigned32 0..65535  

sheAdslLineAlarmConfProfileAtucThreshInterleaveRateDown 1.3.6.1.4.1.231.7.1.2.1.6.1.1.22.1.7
Applies to `Interleave' channels only. Configured change in rate causing an adslAtucRateChangeTrap. A trap is produced when:ChanCurrTxRate <= ChanPrevTxRate minus the value of this object. A value of `0' will disable the trap.
OBJECT-TYPE    
  Unsigned32 0..65535  

sheAdslLineAlarmConfProfileAtucInitFailureTrapEnable 1.3.6.1.4.1.231.7.1.2.1.6.1.1.22.1.8
Enables and disables the InitFailureTrap. This object is defaulted disable(2).
OBJECT-TYPE    
  TruthValue  

sheAdslLineAlarmConfProfileAtucThresh15MinLofs 1.3.6.1.4.1.231.7.1.2.1.6.1.1.22.1.9
The number of Loss of Frame Seconds encountered by an ADSL interface within any given 15 minutes performance data collection period, which causes the SNMP agent to send an adslAtucPerfLofsThreshTrap. One trap will be sent per interval per interface. A value of `0' will disable the trap.
OBJECT-TYPE    
  INTEGER 0..900  

sheAdslLineAlarmConfProfileAtucThresh15MinLoss 1.3.6.1.4.1.231.7.1.2.1.6.1.1.22.1.10
The number of Loss of Signal Seconds encountered by an ADSL interface within any given 15 minutes performance data collection period, which causes the SNMP agent to send an adslAtucPerfLossThreshTrap. One trap will be sent per interval per interface. A value of `0' will disable the trap.
OBJECT-TYPE    
  INTEGER 0..900  

sheAdslLineAlarmConfProfileAtucThresh15MinLols 1.3.6.1.4.1.231.7.1.2.1.6.1.1.22.1.11
The number of Loss of Link Seconds encountered by an ADSL interface within any given 15 minutes performance data collection period, which causes the SNMP agent to send an adslAtucPerfLolsThreshTrap. One trap will be sent per interval per interface. A value of `0' will disable the trap.
OBJECT-TYPE    
  INTEGER 0..900  

sheAdslLineAlarmConfProfileAtucThresh15MinLprs 1.3.6.1.4.1.231.7.1.2.1.6.1.1.22.1.12
The number of Loss of Power Seconds encountered by an ADSL interface within any given 15 minutes performance data collection period, which causes the SNMP agent to send an adslAtucPerfLprsThreshTrap. One trap will be sent per interval per interface. A value of `0' will disable the trap.
OBJECT-TYPE    
  INTEGER 0..900  

sheAdslLineAlarmConfProfileAtucThresh15MinESs 1.3.6.1.4.1.231.7.1.2.1.6.1.1.22.1.13
The number of Errored Seconds encountered by an ADSL interface within any given 15 minutes performance data collection period, which causes the SNMP agent to send an adslAtucPerfESsThreshTrap. One trap will be sent per interval per interface. A value of `0' will disable the trap.
OBJECT-TYPE    
  INTEGER 0..900  

sheAdslLineAlarmConfProfileAtucThresh15MinSesL 1.3.6.1.4.1.231.7.1.2.1.6.1.1.22.1.14
The number of Severe errored seconds encountered by an ADSL interface within any giving 15 minutes performance data collection period, which cause the SNMP agend to send an adslAtucPerfSesLTrap. One trap will be sent per interval per interface. A value of `0' will disable the trap.
OBJECT-TYPE    
  INTEGER 0..900  

sheAdslLineAlarmConfProfileAtucThresh15MinUasL 1.3.6.1.4.1.231.7.1.2.1.6.1.1.22.1.15
The number of Unavailable seconds encountered by an ADSL interface within any giving 15 minutes performance data collection period, which cause the SNMP agend to send an adslAtucPerfUasLTrap. One trap will be sent per interval per interface. A value of `0' will disable the trap.
OBJECT-TYPE    
  INTEGER 0..900  

sheAdslLineAlarmConfProfileAtucThresh15MinFailFastR 1.3.6.1.4.1.231.7.1.2.1.6.1.1.22.1.16
The number of failed retrains encountered by an ADSL interface within any giving 15 minutes performance data collection period, which cause the SNMP agent to send an adslAtucFailedFastRTrap. Not supported yet!
OBJECT-TYPE    
  INTEGER 0..900  

sheAdslLineAlarmConfProfileAturThreshFastRateUp 1.3.6.1.4.1.231.7.1.2.1.6.1.1.22.1.17
Applies to `Fast' channels only. Configured change in rate causing an adslAturRateChangeTrap. A trap is produced when: ChanCurrTxRate >= ChanPrevTxRate plus the value of this object. A value of `0' will disable the trap.
OBJECT-TYPE    
  Unsigned32 0..65535  

sheAdslLineAlarmConfProfileAturThreshInterleaveRateUp 1.3.6.1.4.1.231.7.1.2.1.6.1.1.22.1.18
Applies to `Interleave' channels only. Configured change in rate causing an adslAturRateChangeTrap. A trap is produced when: ChanCurrTxRate >= ChanPrevTxRate plus the value of this object. A value of `0' will disable the trap.
OBJECT-TYPE    
  Unsigned32 0..65535  

sheAdslLineAlarmConfProfileAturThreshFastRateDown 1.3.6.1.4.1.231.7.1.2.1.6.1.1.22.1.19
Applies to `Fast' channels only. Configured change in rate causing an adslAturRateChangeTrap. A trap is produced when: ChanCurrTxRate <= ChanPrevTxRate minus the value of this object. A value of `0' will disable the trap.
OBJECT-TYPE    
  Unsigned32 0..65535  

sheAdslLineAlarmConfProfileAturThreshInterleaveRateDown 1.3.6.1.4.1.231.7.1.2.1.6.1.1.22.1.20
Applies to `Interleave' channels only. Configured change in rate causing an adslAturRateChangeTrap. A trap is produced when: ChanCurrTxRate <= ChanPrevTxRate minus the value of this object. A value of `0' will disable the trap.
OBJECT-TYPE    
  Unsigned32 0..65535  

sheAdslLineAlarmConfProfileAturThresh15MinLofs 1.3.6.1.4.1.231.7.1.2.1.6.1.1.22.1.21
The number of Loss of Frame Seconds encountered by an ADSL interface within any given 15 minutes performance data collection period, which causes the SNMP agent to send an adslAturPerfLofsThreshTrap. One trap will be sent per interval per interface. A value of `0' will disable the trap.
OBJECT-TYPE    
  INTEGER 0..900  

sheAdslLineAlarmConfProfileAturThresh15MinLoss 1.3.6.1.4.1.231.7.1.2.1.6.1.1.22.1.22
The number of Loss of Signal Seconds encountered by an ADSL interface within any given 15 minutes performance data collection period, which causes the SNMP agent to send an adslAturPerfLossThreshTrap. One trap will be sent per interval per interface. A value of `0' will disable the trap.
OBJECT-TYPE    
  INTEGER 0..900  

sheAdslLineAlarmConfProfileAturThresh15MinLprs 1.3.6.1.4.1.231.7.1.2.1.6.1.1.22.1.23
The number of Loss of Power Seconds encountered by an ADSL interface within any given 15 minutes performance data collection period, which causes the SNMP agent to send an adslAturPerfLprsThreshTrap. One trap will be sent per interval per interface. A value of `0' will disable the trap.
OBJECT-TYPE    
  INTEGER 0..900  

sheAdslLineAlarmConfProfileAturThresh15MinESs 1.3.6.1.4.1.231.7.1.2.1.6.1.1.22.1.24
The number of Errored Seconds encountered by an ADSL interface within any given 15 minutes performance data collection period, which causes the SNMP agent to send an adslAturPerfESsThreshTrap. One trap will be sent per interval per interface. A value of `0' will disable the trap.
OBJECT-TYPE    
  INTEGER 0..900  

sheAdslLineAlarmConfProfileAturThresh15MinSesL 1.3.6.1.4.1.231.7.1.2.1.6.1.1.22.1.25
The number of Severe errored seconds encountered by an ADSL interface within any given 15 minutes performance data collection period, which causes the SNMP agent to send an adslAturPerfSesLThreshTrap. One trap will be sent per interval per interface. A value of `0' will disable the trap.
OBJECT-TYPE    
  INTEGER 0..900  

sheAdslLineAlarmConfProfileAturThresh15MinUasL 1.3.6.1.4.1.231.7.1.2.1.6.1.1.22.1.26
The number of Unavailable seconds encountered by an ADSL interface within any giving 15 minutes performance data collection period, which cause the SNMP agend to send an adslAturPerfUasLTrap. One trap will be sent per interval per interface. A value of `0' will disable the trap.
OBJECT-TYPE