SFRAP-MIB

File: SFRAP-MIB.mib (434368 bytes)

Imported modules

SNMPv2-TC RFC1155-SMI RFC-1215
RFC-1212

Imported symbols

DisplayString Counter TimeTicks
IpAddress internet Gauge
TRAP-TYPE OBJECT-TYPE

Defined Types

SfrapCfgSnmpMgrEntry  
SEQUENCE    
  sfrapCfgSnmpMgrIndex INTEGER
  sfrapCfgSnmpMgrIP IpAddress
  sfrapCfgSnmpMgrInterface INTEGER
  sfrapCfgSnmpMgrDlci INTEGER

SfrapCfgDteEntry  
SEQUENCE    
  sfrapCfgDteIndex INTEGER
  sfrapCfgDteIntfType INTEGER
  sfrapCfgDteTxClockMode INTEGER
  sfrapCfgDteRxClockMode INTEGER
  sfrapCfgDteRtsC INTEGER

SfrapCfgTransitDelayEntry  
SEQUENCE    
  sfrapCfgTransitDelayInterface INTEGER
  sfrapCfgTransitDelayDlciValue INTEGER
  sfrapCfgTransitDelayNumHops INTEGER
  sfrapCfgTransitDelayRcvSummaryCancel INTEGER
  sfrapCfgTransitDelayThreshold INTEGER

SfrapCfgTDDeleteEntry  
SEQUENCE    
  sfrapCfgTDDeleteInterface INTEGER
  sfrapCfgTDDeleteDlciValue INTEGER

SfrapCfgFrPerfDlciNamesEntry  
SEQUENCE    
  sfrapCfgFrPerfDlciNamesDlciValue INTEGER
  sfrapCfgFrPerfDlciNamesDlciName DisplayString Size(0..15)
  sfrapCfgFrPerfDlciNamesCirValue INTEGER
  sfrapCfgFrPerfDlciNamesCirType INTEGER
  sfrapCfgFrPerfDlciNamesUtilThreshold INTEGER
  sfrapCfgFrPerfDlciNamesEirValue INTEGER

SfrapCfgFrPerfUserProtocolsEntry  
SEQUENCE    
  sfrapCfgFrPerfUserProtocolsIndex INTEGER
  sfrapCfgFrPerfUserProtocolsPortNum INTEGER

SfrapCfgFrPerfLTDlciFilterEntry  
SEQUENCE    
  sfrapCfgFrPerfLTDlciFilterIndex INTEGER
  sfrapCfgFrPerfLTDlciFilterDlciNum INTEGER

SfrapCfgFrPerfLTProtocolFilterEntry  
SEQUENCE    
  sfrapCfgFrPerfLTProtocolFilterIndex INTEGER
  sfrapCfgFrPerfLTProtocolFilterProtocol INTEGER

SfrapDiagDteEntry  
SEQUENCE    
  sfrapDiagDteIndex INTEGER
  sfrapDiagDteLclLpbk INTEGER
  sfrapDiagDteTimeRemaining TimeTicks

SFRAPDiagVnipEntry  
SEQUENCE    
  sfrapDiagVnipInterface INTEGER
  sfrapDiagVnipIndex INTEGER
  sfrapDiagVnipDlci INTEGER
  sfrapDiagVnipIpAddr IpAddress
  sfrapDiagVLOOP INTEGER
  sfrapDiagVBERT INTEGER
  sfrapDiagVBERTRate INTEGER
  sfrapDiagVBERTSize INTEGER
  sfrapDiagVBERTPktPercent INTEGER
  sfrapDiagVBERTTestPeriod INTEGER

SfrapStatusDteEntry  
SEQUENCE    
  sfrapStatusDteIndex INTEGER
  sfrapStatusDteMode INTEGER
  sfrapStatusDteRts INTEGER
  sfrapStatusDteDtr INTEGER
  sfrapStatusDteDcd INTEGER
  sfrapStatusDteDsr INTEGER
  sfrapStatusDteCts INTEGER
  sfrapStatusDteSendtiming INTEGER
  sfrapStatusDteRxtiming INTEGER
  sfrapStatusDteTermtiming INTEGER
  sfrapStatusDteCtrl INTEGER
  sfrapStatusDteInd INTEGER

SfrapVnipTopologyEntry  
SEQUENCE    
  sfrapVnipTopologyInterface INTEGER
  sfrapVnipTopologyIndex INTEGER
  sfrapVnipTopologyDlci INTEGER
  sfrapVnipTopologyIpAddr IpAddress
  sfrapVnipTopologyNumHops INTEGER
  sfrapVnipTopologyLocalDlci INTEGER
  sfrapVnipTopoTDNumSamples Counter
  sfrapVnipTopoTDAvgDelay Counter
  sfrapVnipTopoTDMaxDelay Counter
  sfrapVnipTopoTDMinDelay Counter
  sfrapVnipTopoTDLastDelay Counter
  sfrapVnipTopoVLOOPStatus INTEGER
  sfrapVnipTopoVBERTStatus INTEGER
  sfrapVnipTopoVBertTxDESetFrames Counter
  sfrapVnipTopoVBertRxDESetFrames Counter
  sfrapVnipTopoVBertTxDEClrFrames Counter
  sfrapVnipTopoVBertRxDEClrFrames Counter
  sfrapVnipTopoVBertTransitDelayMax Counter
  sfrapVnipTopoVBertTransitDelayAvg Counter
  sfrapVnipTopoVBertTimeElapse TimeTicks
  sfrapVnipTopoVBertPerUtilCIR INTEGER
  sfrapVnipTopoVBertPerUtilEIR INTEGER

Index  
INTEGER    

SfrapPerfThruputPerIntfEntry  
SEQUENCE    
  sfrapPerfThruputPerIntfIndex INTEGER
  sfrapPerfThruputPerIntfRxByteCnt Counter
  sfrapPerfThruputPerIntfTxByteCnt Counter
  sfrapPerfThruputPerIntfRxFrameCnt Counter
  sfrapPerfThruputPerIntfTxFrameCnt Counter
  sfrapPerfThruputPerIntfRxCrcErrCnt Counter
  sfrapPerfThruputPerIntfRxAbortCnt Counter
  sfrapPerfThruputPerIntfRxBpvCnt Counter

SfrapPerfThruputPerDlciEntry  
SEQUENCE    
  sfrapPerfThruputPerDlciIndex Index
  sfrapPerfThruputPerDlciValue INTEGER
  sfrapPerfThruputPerDlciCreateTime INTEGER
  sfrapPerfThruputPerDlciChangeTime INTEGER
  sfrapPerfThruputPerDlciRxByte Counter
  sfrapPerfThruputPerDlciTxByte Counter
  sfrapPerfThruputPerDlciRxFrame Counter
  sfrapPerfThruputPerDlciTxFrame Counter
  sfrapPerfThruputPerDlciRxFecn Counter
  sfrapPerfThruputPerDlciRxBecn Counter
  sfrapPerfThruputPerDlciRxDe Counter
  sfrapPerfThruputPerDlciTxDe Counter
  sfrapPerfThruputPerDlciRxThruput INTEGER
  sfrapPerfThruputPerDlciTxThruput INTEGER
  sfrapPerfThruputPerDlciCIR INTEGER
  sfrapPerfThruputPerDlciUptime INTEGER
  sfrapPerfThruputPerDlciDowntime INTEGER
  sfrapPerfThruputPerDlciCirType INTEGER
  sfrapPerfThruputPerDlciPvcState INTEGER
  sfrapPerfThruputPerDlciOutageCount Counter
  sfrapPerfThruputPerDlciAvailability INTEGER
  sfrapPerfThruputPerDlciMTBSO INTEGER
  sfrapPerfThruputPerDlciMTTSR INTEGER
  sfrapPerfThruputPerDlciEncapType INTEGER
  sfrapPerfThruputPerDlciRxUtilizationStatus INTEGER
  sfrapPerfThruputPerDlciTxUtilizationStatus INTEGER
  sfrapPerfThruputPerDlciEIR INTEGER

SfrapPerfThruputCmdReplaceDlciEntry  
SEQUENCE    
  sfrapPerfThruputCmdReplaceDlciValue INTEGER
  sfrapPerfThruputCmdReplaceDlciNewValue INTEGER

SfrapPerfNetwProtoPerDlciEntry  
SEQUENCE    
  sfrapPerfNetwProtoPerDlciInterval INTEGER
  sfrapPerfNetwProtoPerDlciValue INTEGER
  sfrapPerfNetwProtoPerDlciRxTotal Counter
  sfrapPerfNetwProtoPerDlciTxTotal Counter
  sfrapPerfNetwProtoPerDlciRxIp Counter
  sfrapPerfNetwProtoPerDlciTxIp Counter
  sfrapPerfNetwProtoPerDlciRxIpx Counter
  sfrapPerfNetwProtoPerDlciTxIpx Counter
  sfrapPerfNetwProtoPerDlciRxSna Counter
  sfrapPerfNetwProtoPerDlciTxSna Counter
  sfrapPerfNetwProtoPerDlciRxArp Counter
  sfrapPerfNetwProtoPerDlciTxArp Counter
  sfrapPerfNetwProtoPerDlciRxCisco Counter
  sfrapPerfNetwProtoPerDlciTxCisco Counter
  sfrapPerfNetwProtoPerDlciRxOther Counter
  sfrapPerfNetwProtoPerDlciTxOther Counter
  sfrapPerfNetwProtoPerDlciRxVnip Counter
  sfrapPerfNetwProtoPerDlciTxVnip Counter
  sfrapPerfNetwProtoPerDlciRxAnnexG Counter
  sfrapPerfNetwProtoPerDlciTxAnnexG Counter

SfrapPerfNetwProtoTotalEntry  
SEQUENCE    
  sfrapPerfNetwProtoTotalInterval INTEGER
  sfrapPerfNetwProtoTotalRxTotal Counter
  sfrapPerfNetwProtoTotalTxTotal Counter
  sfrapPerfNetwProtoTotalRxIp Counter
  sfrapPerfNetwProtoTotalTxIp Counter
  sfrapPerfNetwProtoTotalRxIpx Counter
  sfrapPerfNetwProtoTotalTxIpx Counter
  sfrapPerfNetwProtoTotalRxSna Counter
  sfrapPerfNetwProtoTotalTxSna Counter
  sfrapPerfNetwProtoTotalRxArp Counter
  sfrapPerfNetwProtoTotalTxArp Counter
  sfrapPerfNetwProtoTotalRxCisco Counter
  sfrapPerfNetwProtoTotalTxCisco Counter
  sfrapPerfNetwProtoTotalRxOther Counter
  sfrapPerfNetwProtoTotalTxOther Counter
  sfrapPerfNetwProtoTotalRxVnip Counter
  sfrapPerfNetwProtoTotalTxVnip Counter
  sfrapPerfNetwProtoTotalRxAnnexG Counter
  sfrapPerfNetwProtoTotalTxAnnexG Counter

SfrapPerfIpPerDlciEntry  
SEQUENCE    
  sfrapPerfIpPerDlciInterval INTEGER
  sfrapPerfIpPerDlciValue INTEGER
  sfrapPerfIpPerDlciRxTotal Counter
  sfrapPerfIpPerDlciTxTotal Counter
  sfrapPerfIpPerDlciRxTcp Counter
  sfrapPerfIpPerDlciTxTcp Counter
  sfrapPerfIpPerDlciRxUdp Counter
  sfrapPerfIpPerDlciTxUdp Counter
  sfrapPerfIpPerDlciRxIcmp Counter
  sfrapPerfIpPerDlciTxIcmp Counter
  sfrapPerfIpPerDlciRxOther Counter
  sfrapPerfIpPerDlciTxOther Counter
  sfrapPerfIpPerDlciRxIgrp Counter
  sfrapPerfIpPerDlciTxIgrp Counter

SfrapPerfIpTotalEntry  
SEQUENCE    
  sfrapPerfIpTotalInterval INTEGER
  sfrapPerfIpTotalRxTotal Counter
  sfrapPerfIpTotalTxTotal Counter
  sfrapPerfIpTotalRxTcp Counter
  sfrapPerfIpTotalTxTcp Counter
  sfrapPerfIpTotalRxUdp Counter
  sfrapPerfIpTotalTxUdp Counter
  sfrapPerfIpTotalRxIcmp Counter
  sfrapPerfIpTotalTxIcmp Counter
  sfrapPerfIpTotalRxOther Counter
  sfrapPerfIpTotalTxOther Counter
  sfrapPerfIpTotalRxIgrp Counter
  sfrapPerfIpTotalTxIgrp Counter

SfrapPerfIcmpPerDlciEntry  
SEQUENCE    
  sfrapPerfIcmpPerDlciInterval INTEGER
  sfrapPerfIcmpPerDlciValue INTEGER
  sfrapPerfIcmpPerDlciRxTotal Counter
  sfrapPerfIcmpPerDlciTxTotal Counter
  sfrapPerfIcmpPerDlciRxEchoRep Counter
  sfrapPerfIcmpPerDlciTxEchoRep Counter
  sfrapPerfIcmpPerDlciRxDestUnr Counter
  sfrapPerfIcmpPerDlciTxDestUnr Counter
  sfrapPerfIcmpPerDlciRxSrcQuench Counter
  sfrapPerfIcmpPerDlciTxSrcQuench Counter
  sfrapPerfIcmpPerDlciRxRedirect Counter
  sfrapPerfIcmpPerDlciTxRedirect Counter
  sfrapPerfIcmpPerDlciRxEchoReq Counter
  sfrapPerfIcmpPerDlciTxEchoReq Counter
  sfrapPerfIcmpPerDlciRxTimeExcd Counter
  sfrapPerfIcmpPerDlciTxTimeExcd Counter
  sfrapPerfIcmpPerDlciRxParamProb Counter
  sfrapPerfIcmpPerDlciTxParamProb Counter
  sfrapPerfIcmpPerDlciRxTimestpReq Counter
  sfrapPerfIcmpPerDlciTxTimestpReq Counter
  sfrapPerfIcmpPerDlciRxTimestpRep Counter
  sfrapPerfIcmpPerDlciTxTimestpRep Counter
  sfrapPerfIcmpPerDlciRxAddrMaskReq Counter
  sfrapPerfIcmpPerDlciTxAddrMaskReq Counter
  sfrapPerfIcmpPerDlciRxAddrMaskRep Counter
  sfrapPerfIcmpPerDlciTxAddrMaskRep Counter
  sfrapPerfIcmpPerDlciRxPktTooBig Counter
  sfrapPerfIcmpPerDlciTxPktTooBig Counter
  sfrapPerfIcmpPerDlciRxGmQuery Counter
  sfrapPerfIcmpPerDlciTxGmQuery Counter
  sfrapPerfIcmpPerDlciRxGmReport Counter
  sfrapPerfIcmpPerDlciTxGmReport Counter
  sfrapPerfIcmpPerDlciRxGmReduct Counter
  sfrapPerfIcmpPerDlciTxGmReduct Counter

SfrapPerfIcmpTotalEntry  
SEQUENCE    
  sfrapPerfIcmpTotalInterval INTEGER
  sfrapPerfIcmpTotalRxTotal Counter
  sfrapPerfIcmpTotalTxTotal Counter
  sfrapPerfIcmpTotalRxEchoRep Counter
  sfrapPerfIcmpTotalTxEchoRep Counter
  sfrapPerfIcmpTotalRxDestUnr Counter
  sfrapPerfIcmpTotalTxDestUnr Counter
  sfrapPerfIcmpTotalRxSrcQuench Counter
  sfrapPerfIcmpTotalTxSrcQuench Counter
  sfrapPerfIcmpTotalRxRedirect Counter
  sfrapPerfIcmpTotalTxRedirect Counter
  sfrapPerfIcmpTotalRxEchoReq Counter
  sfrapPerfIcmpTotalTxEchoReq Counter
  sfrapPerfIcmpTotalRxTimeExcd Counter
  sfrapPerfIcmpTotalTxTimeExcd Counter
  sfrapPerfIcmpTotalRxParamProb Counter
  sfrapPerfIcmpTotalTxParamProb Counter
  sfrapPerfIcmpTotalRxTimestpReq Counter
  sfrapPerfIcmpTotalTxTimestpReq Counter
  sfrapPerfIcmpTotalRxTimestpRep Counter
  sfrapPerfIcmpTotalTxTimestpRep Counter
  sfrapPerfIcmpTotalRxAddrMaskReq Counter
  sfrapPerfIcmpTotalTxAddrMaskReq Counter
  sfrapPerfIcmpTotalRxAddrMaskRep Counter
  sfrapPerfIcmpTotalTxAddrMaskRep Counter
  sfrapPerfIcmpTotalRxPktTooBig Counter
  sfrapPerfIcmpTotalTxPktTooBig Counter
  sfrapPerfIcmpTotalRxGmQuery Counter
  sfrapPerfIcmpTotalTxGmQuery Counter
  sfrapPerfIcmpTotalRxGmReport Counter
  sfrapPerfIcmpTotalTxGmReport Counter
  sfrapPerfIcmpTotalRxGmReduct Counter
  sfrapPerfIcmpTotalTxGmReduct Counter

SfrapPerfApplicationPerDlciEntry  
SEQUENCE    
  sfrapPerfApplicationPerDlciInterval INTEGER
  sfrapPerfApplicationPerDlciValue INTEGER
  sfrapPerfApplicationPerDlciRxSnmp Counter
  sfrapPerfApplicationPerDlciTxSnmp Counter
  sfrapPerfApplicationPerDlciRxSnmpTrap Counter
  sfrapPerfApplicationPerDlciTxSnmpTrap Counter
  sfrapPerfApplicationPerDlciRxHttp Counter
  sfrapPerfApplicationPerDlciTxHttp Counter
  sfrapPerfApplicationPerDlciRxTelnet Counter
  sfrapPerfApplicationPerDlciTxTelnet Counter
  sfrapPerfApplicationPerDlciRxSmtp Counter
  sfrapPerfApplicationPerDlciTxSmtp Counter
  sfrapPerfApplicationPerDlciRxFtp Counter
  sfrapPerfApplicationPerDlciTxFtp Counter
  sfrapPerfApplicationPerDlciRxTftp Counter
  sfrapPerfApplicationPerDlciTxTftp Counter
  sfrapPerfApplicationPerDlciRxCustom1 Counter
  sfrapPerfApplicationPerDlciTxCustom1 Counter
  sfrapPerfApplicationPerDlciRxCustom2 Counter
  sfrapPerfApplicationPerDlciTxCustom2 Counter
  sfrapPerfApplicationPerDlciRxCustom3 Counter
  sfrapPerfApplicationPerDlciTxCustom3 Counter
  sfrapPerfApplicationPerDlciRxCustom4 Counter
  sfrapPerfApplicationPerDlciTxCustom4 Counter

SfrapPerfApplicationTotalEntry  
SEQUENCE    
  sfrapPerfApplicationTotalInterval INTEGER
  sfrapPerfApplicationTotalRxSnmp Counter
  sfrapPerfApplicationTotalTxSnmp Counter
  sfrapPerfApplicationTotalRxSnmpTrap Counter
  sfrapPerfApplicationTotalTxSnmpTrap Counter
  sfrapPerfApplicationTotalRxHttp Counter
  sfrapPerfApplicationTotalTxHttp Counter
  sfrapPerfApplicationTotalRxTelnet Counter
  sfrapPerfApplicationTotalTxTelnet Counter
  sfrapPerfApplicationTotalRxSmtp Counter
  sfrapPerfApplicationTotalTxSmtp Counter
  sfrapPerfApplicationTotalRxFtp Counter
  sfrapPerfApplicationTotalTxFtp Counter
  sfrapPerfApplicationTotalRxTftp Counter
  sfrapPerfApplicationTotalTxTftp Counter
  sfrapPerfApplicationTotalRxCustom1 Counter
  sfrapPerfApplicationTotalTxCustom1 Counter
  sfrapPerfApplicationTotalRxCustom2 Counter
  sfrapPerfApplicationTotalTxCustom2 Counter
  sfrapPerfApplicationTotalRxCustom3 Counter
  sfrapPerfApplicationTotalTxCustom3 Counter
  sfrapPerfApplicationTotalRxCustom4 Counter
  sfrapPerfApplicationTotalTxCustom4 Counter

SfrapPerfRoutingPerDlciEntry  
SEQUENCE    
  sfrapPerfRoutingPerDlciInterval INTEGER
  sfrapPerfRoutingPerDlciValue INTEGER
  sfrapPerfRoutingPerDlciRxOspf Counter
  sfrapPerfRoutingPerDlciTxOspf Counter
  sfrapPerfRoutingPerDlciRxRip Counter
  sfrapPerfRoutingPerDlciTxRip Counter
  sfrapPerfRoutingPerDlciRxNetbios Counter
  sfrapPerfRoutingPerDlciTxNetbios Counter

SfrapPerfRoutingTotalEntry  
SEQUENCE    
  sfrapPerfRoutingTotalInterval INTEGER
  sfrapPerfRoutingTotalRxOspf Counter
  sfrapPerfRoutingTotalTxOspf Counter
  sfrapPerfRoutingTotalRxRip Counter
  sfrapPerfRoutingTotalTxRip Counter
  sfrapPerfRoutingTotalRxNetbios Counter
  sfrapPerfRoutingTotalTxNetbios Counter

SfrapPerfIpxPerDlciEntry  
SEQUENCE    
  sfrapPerfIpxPerDlciInterval INTEGER
  sfrapPerfIpxPerDlciValue INTEGER
  sfrapPerfIpxPerDlciRxTotal Counter
  sfrapPerfIpxPerDlciTxTotal Counter
  sfrapPerfIpxPerDlciRxSpx Counter
  sfrapPerfIpxPerDlciTxSpx Counter
  sfrapPerfIpxPerDlciRxNcp Counter
  sfrapPerfIpxPerDlciTxNcp Counter
  sfrapPerfIpxPerDlciRxSap Counter
  sfrapPerfIpxPerDlciTxSap Counter
  sfrapPerfIpxPerDlciRxRip Counter
  sfrapPerfIpxPerDlciTxRip Counter
  sfrapPerfIpxPerDlciRxNetbios Counter
  sfrapPerfIpxPerDlciTxNetbios Counter
  sfrapPerfIpxPerDlciRxOther Counter
  sfrapPerfIpxPerDlciTxOther Counter

SfrapPerfIpxTotalEntry  
SEQUENCE    
  sfrapPerfIpxTotalInterval INTEGER
  sfrapPerfIpxTotalRxTotal Counter
  sfrapPerfIpxTotalTxTotal Counter
  sfrapPerfIpxTotalRxSpx Counter
  sfrapPerfIpxTotalTxSpx Counter
  sfrapPerfIpxTotalRxNcp Counter
  sfrapPerfIpxTotalTxNcp Counter
  sfrapPerfIpxTotalRxSap Counter
  sfrapPerfIpxTotalTxSap Counter
  sfrapPerfIpxTotalRxRip Counter
  sfrapPerfIpxTotalTxRip Counter
  sfrapPerfIpxTotalRxNetbios Counter
  sfrapPerfIpxTotalTxNetbios Counter
  sfrapPerfIpxTotalRxOther Counter
  sfrapPerfIpxTotalTxOther Counter

SfrapPerfSnaPerDlciEntry  
SEQUENCE    
  sfrapPerfSnaPerDlciInterval INTEGER
  sfrapPerfSnaPerDlciValue INTEGER
  sfrapPerfSnaPerDlciRxTotal Counter
  sfrapPerfSnaPerDlciTxTotal Counter
  sfrapPerfSnaPerDlciRxSubarea Counter
  sfrapPerfSnaPerDlciTxSubarea Counter
  sfrapPerfSnaPerDlciRxPeriph Counter
  sfrapPerfSnaPerDlciTxPeriph Counter
  sfrapPerfSnaPerDlciRxAppn Counter
  sfrapPerfSnaPerDlciTxAppn Counter
  sfrapPerfSnaPerDlciRxNetbios Counter
  sfrapPerfSnaPerDlciTxNetbios Counter
  sfrapPerfSnaPerDlciRxOther Counter
  sfrapPerfSnaPerDlciTxOther Counter

SfrapPerfSnaTotalEntry  
SEQUENCE    
  sfrapPerfSnaTotalInterval INTEGER
  sfrapPerfSnaTotalRxTotal Counter
  sfrapPerfSnaTotalTxTotal Counter
  sfrapPerfSnaTotalRxSubarea Counter
  sfrapPerfSnaTotalTxSubarea Counter
  sfrapPerfSnaTotalRxPeriph Counter
  sfrapPerfSnaTotalTxPeriph Counter
  sfrapPerfSnaTotalRxAppn Counter
  sfrapPerfSnaTotalTxAppn Counter
  sfrapPerfSnaTotalRxNetbios Counter
  sfrapPerfSnaTotalTxNetbios Counter
  sfrapPerfSnaTotalRxOther Counter
  sfrapPerfSnaTotalTxOther Counter

SfrapPerfArpPerDlciEntry  
SEQUENCE    
  sfrapPerfArpPerDlciInterval INTEGER
  sfrapPerfArpPerDlciValue INTEGER
  sfrapPerfArpPerDlciRxTotal Counter
  sfrapPerfArpPerDlciTxTotal Counter
  sfrapPerfArpPerDlciRxArpReq Counter
  sfrapPerfArpPerDlciTxArpReq Counter
  sfrapPerfArpPerDlciRxArpRep Counter
  sfrapPerfArpPerDlciTxArpRep Counter
  sfrapPerfArpPerDlciRxRarpReq Counter
  sfrapPerfArpPerDlciTxRarpReq Counter
  sfrapPerfArpPerDlciRxRarpRep Counter
  sfrapPerfArpPerDlciTxRarpRep Counter
  sfrapPerfArpPerDlciRxInarpReq Counter
  sfrapPerfArpPerDlciTxInarpReq Counter
  sfrapPerfArpPerDlciRxInarpRep Counter
  sfrapPerfArpPerDlciTxInarpRep Counter
  sfrapPerfArpPerDlciRxOther Counter
  sfrapPerfArpPerDlciTxOther Counter

SfrapPerfArpTotalEntry  
SEQUENCE    
  sfrapPerfArpTotalInterval INTEGER
  sfrapPerfArpTotalRxTotal Counter
  sfrapPerfArpTotalTxTotal Counter
  sfrapPerfArpTotalRxArpReq Counter
  sfrapPerfArpTotalTxArpReq Counter
  sfrapPerfArpTotalRxArpRep Counter
  sfrapPerfArpTotalTxArpRep Counter
  sfrapPerfArpTotalRxRarpReq Counter
  sfrapPerfArpTotalTxRarpReq Counter
  sfrapPerfArpTotalRxRarpRep Counter
  sfrapPerfArpTotalTxRarpRep Counter
  sfrapPerfArpTotalRxInarpReq Counter
  sfrapPerfArpTotalTxInarpReq Counter
  sfrapPerfArpTotalRxInarpRep Counter
  sfrapPerfArpTotalTxInarpRep Counter
  sfrapPerfArpTotalRxOther Counter
  sfrapPerfArpTotalTxOther Counter

SfrapPerfLmiPerDlciEntry  
SEQUENCE    
  sfrapPerfLmiPerDlciInterval INTEGER
  sfrapPerfLmiPerDlciValue INTEGER
  sfrapPerfLmiPerDlciRxTotalByteCnt Counter
  sfrapPerfLmiPerDlciTxTotalByteCnt Counter
  sfrapPerfLmiPerDlciRxLivoEnqByteCnt Counter
  sfrapPerfLmiPerDlciTxLivoEnqByteCnt Counter
  sfrapPerfLmiPerDlciRxLivoStatByteCnt Counter
  sfrapPerfLmiPerDlciTxLivoStatByteCnt Counter
  sfrapPerfLmiPerDlciRxFullEnqByteCnt Counter
  sfrapPerfLmiPerDlciTxFullEnqByteCnt Counter
  sfrapPerfLmiPerDlciRxFullStatByteCnt Counter
  sfrapPerfLmiPerDlciTxFullStatByteCnt Counter
  sfrapPerfLmiPerDlciRxOtherByteCnt Counter
  sfrapPerfLmiPerDlciTxOtherByteCnt Counter

SfrapPerfLmiTotalEntry  
SEQUENCE    
  sfrapPerfLmiTotalInterval INTEGER
  sfrapPerfLmiTotalDlciValue INTEGER
  sfrapPerfLmiTotalRxTotalByteCnt Counter
  sfrapPerfLmiTotalTxTotalByteCnt Counter
  sfrapPerfLmiTotalRxLivoEnqByteCnt Counter
  sfrapPerfLmiTotalTxLivoEnqByteCnt Counter
  sfrapPerfLmiTotalRxLivoStatByteCnt Counter
  sfrapPerfLmiTotalTxLivoStatByteCnt Counter
  sfrapPerfLmiTotalRxFullEnqByteCnt Counter
  sfrapPerfLmiTotalTxFullEnqByteCnt Counter
  sfrapPerfLmiTotalRxFullStatByteCnt Counter
  sfrapPerfLmiTotalTxFullStatByteCnt Counter
  sfrapPerfLmiTotalRxOtherByteCnt Counter
  sfrapPerfLmiTotalTxOtherByteCnt Counter

SfrapPerfNetwLongTermEntry  
SEQUENCE    
  sfrapPerfNetwLongTermDlci INTEGER
  sfrapPerfNetwLongTermProtocol INTEGER
  sfrapPerfNetwLongTermInterval INTEGER
  sfrapPerfNetwLongTermValue Counter

SfrapPerfNetwLongTermAltEntry  
SEQUENCE    
  sfrapPerfNetwLongTermAltDlci INTEGER
  sfrapPerfNetwLongTermAltProtocol INTEGER
  sfrapPerfNetwLongTermAltArray OCTET STRING

SfrapPerfCirPercentUtilizationEntry  
SEQUENCE    
  sfrapPerfCirPercentUtilizationInterval INTEGER
  sfrapPerfCirPercentUtilizationDlciValue INTEGER
  sfrapPerfCirRxPercentUtilizationRange1 INTEGER
  sfrapPerfCirRxPercentUtilizationRange2 INTEGER
  sfrapPerfCirRxPercentUtilizationRange3 INTEGER
  sfrapPerfCirRxPercentUtilizationRange4 INTEGER
  sfrapPerfCirRxPercentUtilizationRange5 INTEGER
  sfrapPerfCirRxPercentUtilizationRange6 INTEGER
  sfrapPerfCirRxPercentUtilizationRange7 INTEGER
  sfrapPerfCirRxPercentUtilizationRange8 INTEGER
  sfrapPerfCirTxPercentUtilizationRange1 INTEGER
  sfrapPerfCirTxPercentUtilizationRange2 INTEGER
  sfrapPerfCirTxPercentUtilizationRange3 INTEGER
  sfrapPerfCirTxPercentUtilizationRange4 INTEGER
  sfrapPerfCirTxPercentUtilizationRange5 INTEGER
  sfrapPerfCirTxPercentUtilizationRange6 INTEGER
  sfrapPerfCirTxPercentUtilizationRange7 INTEGER
  sfrapPerfCirTxPercentUtilizationRange8 INTEGER

SfrapPerfCurrentPerDlciUtilizationEntry  
SEQUENCE    
  sfrapPerfCurrentPerDlciUtilizationDlciValue INTEGER
  sfrapPerfCurrentPerDlciRxUtilization INTEGER
  sfrapPerfCurrentPerDlciTxUtilization INTEGER
  sfrapPerfCurrentPerDlciAggregateUtilization INTEGER

SFRAPEventTrapLogEntry  
SEQUENCE    
  sfrapEventTrapLogSeqNum INTEGER
  sfrapEventTrapLogGenericEvent INTEGER
  sfrapEventTrapLogSpecificEvent INTEGER
  sfrapEventTrapLogTimeStamp TimeTicks
  sfrapEventTrapLogVarBind1 INTEGER
  sfrapEventTrapLogVarBind2 INTEGER
  sfrapEventTrapLogVarBind3 INTEGER

SFRAPEventLogAltEntry  
SEQUENCE    
  sfrapEventLogAltSeqNum INTEGER
  sfrapEventLogAltArray OCTET STRING

Defined Values

private 1.3.6.1.4
OBJECT IDENTIFIER    

enterprises 1.3.6.1.4.1
OBJECT IDENTIFIER    

sync 1.3.6.1.4.1.485
OBJECT IDENTIFIER    

sfrap 1.3.6.1.4.1.485.7
OBJECT IDENTIFIER    

sfrapSystem 1.3.6.1.4.1.485.7.1
OBJECT IDENTIFIER    

sfrapSysTable 1.3.6.1.4.1.485.7.1.1
OBJECT IDENTIFIER    

sfrapSysType 1.3.6.1.4.1.485.7.1.1.1
A textual description of the system model identifier. for example: SYNC-sfrap
Status: mandatory Access: read-only
OBJECT-TYPE    
  DisplayString Size(0..255)  

sfrapSysSoftRev 1.3.6.1.4.1.485.7.1.1.2
Displays the Software Revision of the application code installed in this node.
Status: mandatory Access: read-only
OBJECT-TYPE    
  DisplayString Size(0..10)  

sfrapSysHardRev 1.3.6.1.4.1.485.7.1.1.3
Displays the Hardware Revision of the node.
Status: mandatory Access: read-only
OBJECT-TYPE    
  DisplayString Size(0..10)  

sfrapSysNumToDteInstalled 1.3.6.1.4.1.485.7.1.1.5
The number of channels (TO-DTE) that are installed.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER 0..1  

sfrapSysNumToDceInstalled 1.3.6.1.4.1.485.7.1.1.14
The number of channels (TO-DCE) that are installed.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER 0..1  

sfrapSysNumMaintInstalled 1.3.6.1.4.1.485.7.1.1.6
The number of Maintenance ports that are installed.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER 0..2  

sfrapSysName 1.3.6.1.4.1.485.7.1.1.7
The user supplied name of the node. This object does not affect operation, but may be useful for network management.
Status: mandatory Access: read-write
OBJECT-TYPE    
  DisplayString Size(0..16)  

sfrapSysSerialNo 1.3.6.1.4.1.485.7.1.1.8
The serial number of the board.
Status: mandatory Access: read-only
OBJECT-TYPE    
  DisplayString Size(0..10)  

sfrapSysResetNode 1.3.6.1.4.1.485.7.1.1.9
Command to reset the node. NODE WILL BE OFF-LINE AND USER DATA WILL BE INTERRUPTED FOR APPROXIMATELY 15 SECONDS.
Status: mandatory Access: write-only
OBJECT-TYPE    
  INTEGER reset-node(321)  

sfrapSysAmtMemoryInstalled 1.3.6.1.4.1.485.7.1.1.10
The amount of memory (RAM) installed (in megabytes).
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER  

sfrapSysLocation 1.3.6.1.4.1.485.7.1.1.12
The user supplied location of the node. This object does not affect operation, but may be useful for network management.
Status: mandatory Access: read-write
OBJECT-TYPE    
  DisplayString Size(0..16)  

sfrapSysContact 1.3.6.1.4.1.485.7.1.1.13
The user supplied contact information for the node. This object does not affect operation, but may be useful for network management.
Status: mandatory Access: read-write
OBJECT-TYPE    
  DisplayString Size(0..16)  

sfrapSysPrompt 1.3.6.1.4.1.485.7.1.1.15
Configurable Command Line Interface (CLI) prompt. CLI is the User Interface protocol used for directly attached VT100 terminal access as well as Remote access via Telnet.
Status: mandatory Access: read-write
OBJECT-TYPE    
  DisplayString Size(0..8)  

sfrapSysBootRev 1.3.6.1.4.1.485.7.1.1.16
Displays the Software Revision of the Bootstrapping code installed in this node.
Status: mandatory Access: read-only
OBJECT-TYPE    
  DisplayString Size(0..10)  

sfrapSysFeatureTable 1.3.6.1.4.1.485.7.1.2
OBJECT IDENTIFIER    

sfrapSysSLIPSupported 1.3.6.1.4.1.485.7.1.2.1
Shows whether the unit has SLIP (Serial Line IP) capability. SLIP is a method for out-of-band management that connects through the asynchronous terminal port.
Status: mandatory Access: read-only
OBJECT-TYPE    
  DisplayString Size(0..10)  

sfrapSysPPPSupported 1.3.6.1.4.1.485.7.1.2.2
Shows whether the unit has PPP (Point to Point protocol) capability. PPP is a method for out-of-band management that connects through the asynchronous terminal port.
Status: mandatory Access: read-only
OBJECT-TYPE    
  DisplayString Size(0..10)  

sfrapSysRDOSupported 1.3.6.1.4.1.485.7.1.2.3
Shows whether the unit has Remote Dial Out capability.
Status: mandatory Access: read-only
OBJECT-TYPE    
  DisplayString Size(0..10)  

sfrapSysETHSupported 1.3.6.1.4.1.485.7.1.2.4
Shows whether the unit has Ethernet capability.
Status: mandatory Access: read-only
OBJECT-TYPE    
  DisplayString Size(0..10)  

sfrapSysTKRSupported 1.3.6.1.4.1.485.7.1.2.5
Shows whether the unit has Token Ring capability.
Status: mandatory Access: read-only
OBJECT-TYPE    
  DisplayString Size(0..10)  

sfrapSysExtTimSupported 1.3.6.1.4.1.485.7.1.2.6
Shows whether the unit has External Timing capability. This is the ability to derive WAN timing from the DTE port.
Status: mandatory Access: read-only
OBJECT-TYPE    
  DisplayString Size(0..10)  

sfrapSysBRISupported 1.3.6.1.4.1.485.7.1.2.7
Shows whether the unit has BRI (ISDN Basic Rate) capability.
Status: mandatory Access: read-only
OBJECT-TYPE    
  DisplayString Size(0..10)  

sfrapSysSelDTESupported 1.3.6.1.4.1.485.7.1.2.8
Shows whether the unit has a Selectable DTE interface. This being the ability to select amongst various electrical interface formats (V.35, RS449, RS232, etc.) via software.
Status: mandatory Access: read-only
OBJECT-TYPE    
  DisplayString Size(0..10)  

sfrapSysMLSupported 1.3.6.1.4.1.485.7.1.2.9
Shows whether the unit supports MLs (out-of-band management links).
Status: mandatory Access: read-only
OBJECT-TYPE    
  DisplayString Size(0..10)  

sfrapSysNumDlcisSupported 1.3.6.1.4.1.485.7.1.2.10
Shows how many DLCIs can be monitored for frame-based statistics. The unit will pass an unlimited number of DLCIs but will only collect statistics on this number (first come first served).
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER  

sfrapSysLTFNumDlcis 1.3.6.1.4.1.485.7.1.2.11
Shows how many DLCIs can be specified in the Long Term Statistics Filter.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER  

sfrapSysLTFNumProtocols 1.3.6.1.4.1.485.7.1.2.12
Shows how many protocols can be specified in the Long Term Statistics Filter.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER  

sfrapSysNumUserProtocols 1.3.6.1.4.1.485.7.1.2.13
Shows how many protocols can be defined by the user. The user configures TCP/UDP ports which can be monitored as protocols. They are available for short term or long term statistics monitoring.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER  

sfrapSysNumSnmpMgrs 1.3.6.1.4.1.485.7.1.2.14
Shows how many SNMP managers can be programmed in the table sfrapCfgSnmpMngrTable. These managers are sent TRAPs if configured to do so.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER  

sfrapSysNumDlciNames 1.3.6.1.4.1.485.7.1.2.15
Shows how many DLCI names can be defined by the user in the table sfrapCfgFrPerfDlciNamesTable.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER  

sfrapSysHighSpeedSupported 1.3.6.1.4.1.485.7.1.2.16
Shows whether the unit is in high speed mode.
Status: mandatory Access: read-only
OBJECT-TYPE    
  DisplayString Size(0..10)  

sfrapConfiguration 1.3.6.1.4.1.485.7.2
OBJECT IDENTIFIER    

sfrapCfgMgmtTable 1.3.6.1.4.1.485.7.2.1
OBJECT IDENTIFIER    

sfrapCfgIpTable 1.3.6.1.4.1.485.7.2.1.1
OBJECT IDENTIFIER    

sfrapCfgIpMyIP 1.3.6.1.4.1.485.7.2.1.1.1
The IP address for this node. This address will be unique to the IP network and is required for in-band or out-of-band ip and SNMP management.
Status: mandatory Access: read-write
OBJECT-TYPE    
  IpAddress  

sfrapCfgIpPeerIP 1.3.6.1.4.1.485.7.2.1.1.2
This parameter is not used internally by the unit. It is intended to identify either the device directly connected to the SLIP port or, in Frame Relay applications, the address of the primary network management station. This should always be non-zero.
Status: mandatory Access: read-write
OBJECT-TYPE    
  IpAddress  

sfrapCfgIpMask 1.3.6.1.4.1.485.7.2.1.1.3
The IP Subnet Mask (eg 255.255.255.0). This parameter should be consisent with the IP subnet address setting of the external internetworking equipment (router/frad).
Status: mandatory Access: read-write
OBJECT-TYPE    
  IpAddress  

sfrapCfgIpMaxMTU 1.3.6.1.4.1.485.7.2.1.1.4
The Maximum Transmission Unit is the size of the largest IP packet supported (including header). This value should be set to the lowest value supported by any equipment in the transmission path. For Frame Relay management the typical value is 1500. For SLIP management the typical value is 1006.
Status: mandatory Access: read-write
OBJECT-TYPE    
  INTEGER 1..1024  

sfrapCfgIpChannel 1.3.6.1.4.1.485.7.2.1.1.5
This is the method by which IP traffic is being carried. Either via the SLIP port or a DLCI. This is how your InBand Managenent scheme is set up.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER none(1), slip-port(2), in-band-dlci(3)  

sfrapCfgIpTelnetEnable 1.3.6.1.4.1.485.7.2.1.1.6
Enables/Disables the telnet feature. Valid values are enable-telnet (1) and disable-telnet (2).
Status: mandatory Access: read-write
OBJECT-TYPE    
  INTEGER enable-telnet(1), disable-telnet(2)  

sfrapCfgIpTelnetAutoLogOut 1.3.6.1.4.1.485.7.2.1.1.7
If Telnet Auto logout is enabled the unit will automatically disconnect from a Telnet session after a period of inactivity (absence of key strokes from remote terminal). (2) disables this feature (1) auto logout after 15 minutes inactivity (3) auto logout after 3 minutes inactivity (5) auto logout after 5 minutes inactivity (10) auto logout after 10 minutes inactivity (30) auto logout after 30 minutes inactivity (60) auto logout after 60 minutes inactivity
Status: mandatory Access: read-write
OBJECT-TYPE    
  INTEGER autologout-at-15-minutes(1), disable-autologout(2), autologout-at-3-minutes(3), autologout-at-5-minutes(5), autologout-at-10-minutes(10), autologout-at-30-minutes(30), autologout-at-60-minutes(60)  

sfrapCfgTftpTable 1.3.6.1.4.1.485.7.2.1.2
OBJECT IDENTIFIER    

sfrapCfgTftpInitiate 1.3.6.1.4.1.485.7.2.1.2.1
Setting this object to a value that matches the TFTP Password will command the unit to attempt a TFTP file transfer. A TFTP profile including host ip address, dlci value, interface, and file name must first be configured.
Status: mandatory Access: write-only
OBJECT-TYPE    
  DisplayString Size(0..8)  

sfrapCfgTftpIpAddress 1.3.6.1.4.1.485.7.2.1.2.2
The IP address of the TFTP host with which the unit will attempt to establish a TFTP session when initiated.
Status: mandatory Access: read-write
OBJECT-TYPE    
  IpAddress  

sfrapCfgTftpFilename 1.3.6.1.4.1.485.7.2.1.2.3
The name of the file located on the TFTP host that will be transferred to the unit. Typically this is a product-specific software image that will be programmed into unit FLASH. The unit provides several levels of checking to verify the validity and integrity of this file. Note - depending upon the host, this file name may be case sensitive.
Status: mandatory Access: read-write
OBJECT-TYPE    
  DisplayString Size(0..80)  

sfrapCfgTftpInterface 1.3.6.1.4.1.485.7.2.1.2.4
The physical interface out which the TFTP host is located. This parameter is only required for Piggyback and Bi-directional in-band frame relay managed applications. With Local and Remote in-band and SLIP-based applications the interface is known and Sets to this will be ignored.
Status: mandatory Access: read-write
OBJECT-TYPE    
  INTEGER to-dte-interface(1), to-dce-interface(2), slip-interface(3)  

sfrapCfgTftpDlci 1.3.6.1.4.1.485.7.2.1.2.5
The local DLCI value on which the TFTP host can be reached. This DLCI should be active prior to initiating the TFTP session. This parameter is only required for Piggyback in-band frame relay managed applications. With Private management (Local, Remote or Bi-directional in-band applications) the DLCI is known and will be reported here (Sets will be ignored). In SLIP-based applications the DLCI value is not applicable and a value of -1 is reported (Sets will be ignored).
Status: mandatory Access: read-write
OBJECT-TYPE    
  INTEGER -1..63487  

sfrapCfgTftpStatus 1.3.6.1.4.1.485.7.2.1.2.6
The status of current or most recent TFTP operation. (1) TFTP inactive, sets to this value will abort the session (2) TFTP requested (3) TFTP transferring (4) TFTP programming FLASH - unit will reset (5) TFTP fail: session aborted by user or error condition (6) TFTP fail: host no reply - verify TFTP profile and host (7) TFTP fail: file not found - verify file name and location (8) TFTP fail: invalid file - file rejected by unit as inappropriate (9) TFTP fail: corrupt file - session terminated due to checksum error (10) TFTP transfer successful and file has been verified
Status: mandatory Access: read-write
OBJECT-TYPE    
  INTEGER inactive(1), requested(2), transferring(3), programming(4), transfer-aborted(5), host-no-reply(6), file-not-found(7), invalid-file(8), corrupt-file(9), successful(10)  

sfrapCfgTftpNumBytes 1.3.6.1.4.1.485.7.2.1.2.7
The number of Bytes from the ROM image that have been TFTP'd to the unit
Status: mandatory Access: read-only
OBJECT-TYPE    
  Counter  

sfrapCfgSnmpTable 1.3.6.1.4.1.485.7.2.1.3
OBJECT IDENTIFIER    

sfrapCfgSnmpFrTrap 1.3.6.1.4.1.485.7.2.1.3.1
Controls whether or not the Frame Relay DLCI status change traps are issued. These traps are sfrapDLCIActiveTrap and sfrapDLCIInactiveTrap. When sfrapCfgSnmpFrTrap is enabled (1), a trap will be sent each time an individual DLCI changes status between active and inactive. When sfrapCfgSnmpFrTrap is disabled (2), the traps are not sent.
Status: mandatory Access: read-write
OBJECT-TYPE    
  INTEGER enabled(1), disabled(2)  

sfrapCfgSnmpTrapMuting 1.3.6.1.4.1.485.7.2.1.3.3
Controls whether Traps are Sent or Muted. If traps are Muted then a single trap (#75) will be periodically issued by the unit at the programmed frequency. If Muting is Disabled then the full set of Trap events are reported accordingly. (0) Disable Trap Muting (30-10080) Trap Muting frequency in minutes.
Status: mandatory Access: read-write
OBJECT-TYPE    
  INTEGER 0..10080  

sfrapCfgSnmpUtilTrapEnable 1.3.6.1.4.1.485.7.2.1.3.6
Enables or disables the sending of per-DLCI utilization traps. (1) enable utilization traps (2) disable utilization traps
Status: mandatory Access: read-write
OBJECT-TYPE    
  INTEGER enable(1), disable(2)  

sfrapCfgSnmpMgrClearN 1.3.6.1.4.1.485.7.2.1.3.7
Deletes the number of entries in the sfrapCfgSnmpMgrTable indicated by the value. If the value is a positive number the entries will be deleted starting from the first entry. If the value is negative the entries will be deleted starting from the last entry.
Status: mandatory Access: write-only
OBJECT-TYPE    
  INTEGER  

sfrapCfgSnmpMgrTable 1.3.6.1.4.1.485.7.2.1.3.2
The table of SNMP manager profiles to which traps are sent. In all managed modes an SNMP trap mangager's ip address is required as a minimum. Additionally for Piggyback managed units the DLCI and interface must also be configured appropriately. For Local, Remote and SLIP-based management, the DLCI and interface are implied and need not be configured as part of this profile.
Status: mandatory Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    SfrapCfgSnmpMgrEntry

sfrapCfgSnmpMgrEntry 1.3.6.1.4.1.485.7.2.1.3.2.1
The IP address of a SNMP manager to receive this node's TRAPs.
Status: mandatory Access: not-accessible
OBJECT-TYPE    
  SfrapCfgSnmpMgrEntry  

sfrapCfgSnmpMgrIndex 1.3.6.1.4.1.485.7.2.1.3.2.1.1
The index to the list of SNMP managers receiving TRAPs.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER  

sfrapCfgSnmpMgrIP 1.3.6.1.4.1.485.7.2.1.3.2.1.2
The IP address of a SNMP manager to receive this node's TRAPs. Setting this value to 0.0.0.0 will disable the issuance of traps to the indexed manager.
Status: mandatory Access: read-write
OBJECT-TYPE    
  IpAddress  

sfrapCfgSnmpMgrInterface 1.3.6.1.4.1.485.7.2.1.3.2.1.3
The interface out which the indexed trap manager can be reached. This entry is required in Piggyback and Bi-directional in-band managed applications. In Local, Remote and SLIP-based applications, the interface is known and this parameter is ignored. (1) Traps sent out DTE interface for this manager (2) Traps sent out WAN interface for this manager (3) Traps sent out SLIP interface (async maint port) When the node is configured for SLIP, a GET on this MIB object will return slip-interface(3) and a SET of this MIB object to slip-interface(3) is allowed but unnecessary. When the node is not configured for SLIP, this MIB object can be SET to dte-interface(1) or to dce-interface(2); slip-interface(3) would be rejected.
Status: mandatory Access: read-write
OBJECT-TYPE    
  INTEGER to-dte-interface(1), to-dce-interface(2), slip-interface(3)  

sfrapCfgSnmpMgrDlci 1.3.6.1.4.1.485.7.2.1.3.2.1.4
The DLCI out which the indexed trap manager can be reached. This entry is required in Piggyback in-band managed applications. In Private in-band applications the DLCI is known and Sets to this parameter will be ignored. In SLIP mode the DLCI is not applicable, Sets will be ignored and a -1 will be returned as the DLCI value.
Status: mandatory Access: read-write
OBJECT-TYPE    
  INTEGER  

sfrapCfgCommTable 1.3.6.1.4.1.485.7.2.1.4
OBJECT IDENTIFIER    

sfrapCfgCommMode 1.3.6.1.4.1.485.7.2.1.4.1
The protocol running on the Maintenance/Comm port (console). Setting this to SLIP mode will automatically disable in-band management if it's enabled. (1) VT100 for directly attached async terminal (2) SLIP - Serial Line IP out-of-band management
Status: mandatory Access: read-write
OBJECT-TYPE    
  INTEGER vt100(1), slip(2)  

sfrapCfgCommBaud 1.3.6.1.4.1.485.7.2.1.4.2
Asynchronous baud rate for the Maintenance/Comm port (Console). This must be configured to match either the VT100 compatible terminal or the SLIP Terminal Server depending upon the Comm port mode. (2) baud-2400 (4) baud-9600 (5) baud-19200 (6) baud-38400
Status: mandatory Access: read-write
OBJECT-TYPE    
  INTEGER baud-2400(2), baud-9600(4), baud-19200(5), baud-38400(6)  

sfrapCfgCommDataBits 1.3.6.1.4.1.485.7.2.1.4.3
Asynchronous data format for the Maintenance/Comm port (Console). This must be configured to match either the VT100 compatible terminal or the SLIP Terminal Server depending upon the Comm port mode. (1) 7 databits per character (2) 8 databits per character
Status: mandatory Access: read-write
OBJECT-TYPE    
  INTEGER databits-7(1), databits-8(2)  

sfrapCfgCommStopBits 1.3.6.1.4.1.485.7.2.1.4.4
Asynchronous intercharacter protocol for the Maintenance/Comm port (Console). This must be configured to match either the VT100 compatible terminal or the SLIP Terminal Server depending upon the Comm port mode. (1) 1 stopbit (2) 1.5 stopbits (3) 3 stopbits
Status: mandatory Access: read-write
OBJECT-TYPE    
  INTEGER stopbits-1(1), stopbits-1-5(2), stopbits-2(3)  

sfrapCfgCommParity 1.3.6.1.4.1.485.7.2.1.4.5
Asynchronous parity checking protocol for the Maintenance/Comm port (Console). This must be configured to match either the VT100 compatible terminal or the SLIP Terminal Server depending upon the Comm port mode. (1) no parity (2) odd-parity (3) even-parity
Status: mandatory Access: read-write
OBJECT-TYPE    
  INTEGER no-parity(1), odd-parity(2), even-parity(3)  

sfrapCfgCommFlowCtrl 1.3.6.1.4.1.485.7.2.1.4.6
Flow Control for this Communication port. Values are off-flow-control (1).
Status: mandatory Access: read-write
OBJECT-TYPE    
  INTEGER no-flow-control(1)  

sfrapCfgFrDLCITable 1.3.6.1.4.1.485.7.2.1.5
OBJECT IDENTIFIER    

sfrapCfgFrDLCIMode 1.3.6.1.4.1.485.7.2.1.5.1
In-band Frame Relay management mode. A variety of options exist which are differentiated by how PVCs can be provisioned to manage the unit and the resulting impact to the logical processing of Link Management Protocol messages (LMI spoofing and sourcing). The unit is designed to support these management modes even in non-provisioned or failed frame relay networks. This setting also has implications upon how networking protocols such as ARP and InARP are handled by the unit. (1) inactive: in-band management is not enabled (2) local DLCI mode: in-band managed using a private dedicated DLCI accessible via the TO-DTE only. A DLCI value is configured which, through LMI spoofing, will only be visible to the DTE equipment and need not be provisioned on the WAN. All traffic on this DLCI will be terminated by the unit. (3) remote DLCI mode: in-band managed using a private dedicated DLCI accessible via the WAN port only. A DLCI value is configured which, through LMI spoofing, will only be visible from the WAN side and will not be seen by any DTE equipment. All traffic on this DLCI will be terminated by the unit. (4) bidirectional mode: in-band managed using a private dedicated DLCI accessible through either port. A DLCI value is configured which is expected to be fully provisioned in the frame relay network but dedicated to the management function of this particular unit. All traffic on this DLCI will be terminated by the unit. (5) piggyback mode: in-band managed using any DLCI on any interface. A DLCI value is defined that becomes the default DLCI that will be maintained by the unit during network or LMI failure conditions. The unit will terminate and respond accordingly to management and networking data while transparently passing on user data. (6) fixed DCE mode: special mode of operation to support frame relay applications that do not include a switch (frame relay DCE). The unit will independently respond to LMI requests on each interface and will provision the configured DLCI to each Frame Relay DTE device. Except for this, the unit behaves like piggyback.
Status: mandatory Access: read-write
OBJECT-TYPE    
  INTEGER inactive(1), local-to-dte(2), remote-to-dce(3), bidirectional(4), piggyback(5), fixedDCE(6)  

sfrapCfgFrDLCIValue 1.3.6.1.4.1.485.7.2.1.5.2
If in-band management is being used this DLCI value should be defined. In all modes of in-band management with the LMI Sourcing feature enabled the unit may provision this DLCI during LMI failure to facilitate management access. In Private modes (Local, Remote, and Bidirectional) this is the dedicated DLCI for management data and address resolution protocols - all other traffic on this DLCI will be discarded. In Piggyback mode this DLCI is treated like all others except during LMI failure sourcing when it may be provisioned by the unit. In Piggyback mode if InARP is enabled on a single DLCI then this value defines that DLCI.
Status: mandatory Access: read-write
OBJECT-TYPE    
  INTEGER 16..63487  

sfrapCfgFrDLCIEncap 1.3.6.1.4.1.485.7.2.1.5.3
This is the protocol used for enacapsulating and formatting ip data for Frame Relay transmission. This setting is specific to management data to and from the unit. (1) RFC1490 - per IETF standard with Network Level Protocol ID (NLPID) set for IP encapsulation. (2) RFC1490 SNAP/IP - per IETF standard with NLPID set for Sub-Network Access Protocol (SNAP). (3) auto - adjusts to either of these encapsulation techniques as required. (4) Cisco - proprietary encapsulation (4-byte header).
Status: mandatory Access: read-write
OBJECT-TYPE    
  INTEGER rfc1490(1), rfc1490snap(2), auto(3), cisco(4)  

sfrapCfgFrDLCIMgmtDE 1.3.6.1.4.1.485.7.2.1.5.4
Provides user control over the state of the Frame Relay Discard Eligibility bit of all management frames generated by the unit. Frames marked DE=1 are more likely to be dropped in a congested Frame Relay network than those that are DE=0. Heavily congested circumstances can cause both to be dropped. Additionally, frames marked DE=0 may get re-marked to DE=1 by intervening equipment. (1) DE bit cleared to 0: frame is not discard eligible (2) DE bit set to 1: frame is discard eligible
Status: mandatory Access: read-write
OBJECT-TYPE    
  INTEGER no-DE-bit-0(1), yes-DE-bit-1(2)  

sfrapCfgAppTable 1.3.6.1.4.1.485.7.2.2
OBJECT IDENTIFIER    

sfrapCfgAppCircuitId 1.3.6.1.4.1.485.7.2.2.2
Alphanumeric circuit identifier may be provided by the service provider for reference or assigned arbitrarily per user requirements.
Status: mandatory Access: read-write
OBJECT-TYPE    
  DisplayString Size(0..30)  

sfrapCfgAppType 1.3.6.1.4.1.485.7.2.2.3
This unit provides many features specifically adapted to Frame Relay transmission links; this includes diagnostic utilities, statistical analysis, protocol trends, quality of service reporting, and in-band SNMP management. If the unit will be operating in a Frame Relay network the Application Type must be set to Frame Relay to enable these features. To operate in a non-Frame Relay network or to bypass this feature set the unit may be placed in Dedicated mode and will emulate a more familiar DSU/CSU. Note - changing this value will automatically change the Application Format setting and vice versa. (1) dedicated: protocol-independent transparent DSU/CSU (2) Frame Relay: Frame and protocol aware DSU/CSU
Status: mandatory Access: read-write
OBJECT-TYPE    
  INTEGER dedicated(1), frame-relay(2)  

sfrapCfgAppFormat 1.3.6.1.4.1.485.7.2.2.4
Refer to Application Type. Frame Relay is based upon HDLC framing. To operate in a Frame Relay application the Format must be set for HDLC. To operate in a protocol-independent application the Format must be set for Constant Bit Operation (CBO). Note - changing this value will automatically change the Application Type setting and vice versa (1) CBO: protocol-independent transparent DSU/CSU (2) HDLC: Frame and protocol aware DSU/CSU
Status: mandatory Access: read-write
OBJECT-TYPE    
  INTEGER cbo(1), hdlc(2)  

sfrapCfgAppLpbkTimeout 1.3.6.1.4.1.485.7.2.2.5
The length of time a service-impacting loopback or diagnostic utility may run before automatically returning to normal operation. This setting will override any alternatively timed tests (such as VBERT). (0) Loopbak Timeout Disabled (1-1440) Loopback Timeout
Status: mandatory Access: read-write
OBJECT-TYPE    
  INTEGER 0..1440  

sfrapCfgAppTxClkmode 1.3.6.1.4.1.485.7.2.2.6
This MIB object is being obsoleted. The mode in which the TO-DTE and TO-DCE Transmit clocks are set to. The transmit clocks can either be normal or inverted. Here are the choices: 1:Normal-timing both TO-DTE & TO-DCE are set normal 2:Invert-TO-DCE the TO-DCE clock is inverted 3:Invert-TO-DTE the TO-DTE clock is inverted 4:Invert-timing both TO-DTE & TO-DCE are inverted.
Status: mandatory Access: read-write
OBJECT-TYPE    
  INTEGER normal-timing(1), invert-TO-DCE(2), invert-TO-DTE(3), invert-timing(4)  

sfrapCfgAppTxtiming 1.3.6.1.4.1.485.7.2.2.7
Serial Transmit Timing mode. Loop-1 (1) uses the clock returned from the TO-DTE (TT/TCE) to sample tx data, Loop-2 (2) uses the clock (ST/TC) generated by the node to sample tx data. Sourced-tt (3) occurs when the unit is configured for Loop-1 and the clock returned from the TO-DTE (TT/TCE)is not present. The unit will use the (ST/TC) to sample tx data.
Status: mandatory Access: read-write
OBJECT-TYPE    
  INTEGER loop-1(1), loop-2(2), source-tt(3)  

sfrapCfgAppOperationMode 1.3.6.1.4.1.485.7.2.2.8
Describes the Operational Mode of the SFRAP: (1) cut-through used to place unit in cut-thru (2) inband used to place unit in inband.
Status: mandatory Access: read-write
OBJECT-TYPE    
  INTEGER tap(1), inband(2)  

sfrapCfgAppCutthruTimeout 1.3.6.1.4.1.485.7.2.2.9
The amount of time Cuthtru mode may run before timing out and automatically terminating. The timeout is in minutes and a value of 0 means no timeout.
Status: mandatory Access: read-write
OBJECT-TYPE    
  INTEGER 0..1440  

sfrapCfgAppPerfBuffLimit 1.3.6.1.4.1.485.7.2.2.10
This value controls the throttling mechanism used to determine the optimum level of statistical processing versus manageability of the unit. The lower the value (1 - 128), the unit becomes more responsive to management commands during very heavy utilization at the possible expense of statistical accuracy. The larger the value (129 - 512), the more accurate the SFRAP performs statistical analysis of the frames but management may seem slow or unresponsive during periods of very heavy link utilization. NOTE: A value of 0 disables statistical processing entirely.
Status: mandatory Access: read-write
OBJECT-TYPE    
  INTEGER 0..512  

sfrapCfgDteTable 1.3.6.1.4.1.485.7.2.4
The table of DTE port configurations.
Status: mandatory Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    SfrapCfgDteEntry

sfrapCfgDteEntry 1.3.6.1.4.1.485.7.2.4.1
A configuration entry for a DTE port.
Status: mandatory Access: not-accessible
OBJECT-TYPE    
  SfrapCfgDteEntry  

sfrapCfgDteIndex 1.3.6.1.4.1.485.7.2.4.1.99
Selects which DTE port.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER to-dte(1), to-dce(2)  

sfrapCfgDteIntfType 1.3.6.1.4.1.485.7.2.4.1.1
Gets the electrical interface for the DTE port.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER intf-v35(3), intf-rs449(4), intf-x21(5)  

sfrapCfgDteTxClockMode 1.3.6.1.4.1.485.7.2.4.1.3
This selection controls how the unit internally latches the transmit data from the DTE. Normal will sample data with the rising edge of the selected TX Clock, Invert will sample data with the falling edge of the selected TX Clock. The TX Clock is selected using CfgDteTiming. This clock invertion is most useful when loop-2 timing is used - particularly at higher rates and with long cable runs. Only in rare circumstances will clock-invert be used with loop-1 timing. If the DTE Interface TX statistics are indicating excessive crc errors or aborts then changing this setting may have some benefit. (1) normal (2) invert
Status: mandatory Access: read-write
OBJECT-TYPE    
  INTEGER clock-normal(1), clock-invert(2)  

sfrapCfgDteRxClockMode 1.3.6.1.4.1.485.7.2.4.1.21
Clock-normal samples data with the rising edge of the selected rx clock, clock-invert samples data with the falling edge of the selected rx clock,auto-sense forces hardware automated clock selection. The rx clock is selected using CfgDteTiming. This clock invertion is most useful when loop-2 timing is used. Only in rare circumstances will clock-invert (2) be used with loop-1 timing. (3)Auto-sense can only be used on the TO-DTE interface. Auto-sense automatically determines what kind of clocking to use on the TO-DTE interface. THIS OBJECT IS OBSOLETE ON THE TO-DCE INTERFACE
Status: mandatory Access: read-write
OBJECT-TYPE    
  INTEGER clock-normal(1), clock-invert(2), clock-auto(3)  

sfrapCfgDteRtsC 1.3.6.1.4.1.485.7.2.4.1.22
Controls the reporting of the status of the To-DTE port's Request to Send (RTS) and Control (C) control signals, specifically the generation of traps in response to control signal state changes. If Signal Assumed Active, the unit will ignore the actual status and always report this signal Active. If Signal Monitored, the unit will reflect the status as driven by the To-DTE; as such, Traps will be generated due to change of state (these may be useful for a network manager's assessment of interface status. (1) Signal Assumed Active (2) Signal Monitored
Status: mandatory Access: read-write
OBJECT-TYPE    
  INTEGER signal-assumed-active(1), signal-monitored(2)  

sfrapCfgFrTable 1.3.6.1.4.1.485.7.2.5
OBJECT IDENTIFIER    

sfrapCfgFrAddrLen 1.3.6.1.4.1.485.7.2.5.1
Defines the size of the DLCI address field of the Frame Relay header. This setting must correspond to the Frame Relay transmission format; typically Two bytes. (1) two byte DLCI address field (2) three byte DLCI address field (3) four byte DLCI address field
Status: mandatory Access: read-write
OBJECT-TYPE    
  INTEGER twobytes(1), threebytes(2), fourbytes(3)  

sfrapCfgFrCrcMode 1.3.6.1.4.1.485.7.2.5.2
This defines the manner in which the unit handles HDLC protocol errors (crc errors) in a Frame Relay application. If Discard is selected the unit will respond to an errored frame by aborting the frame if transmission has begun; or simply discarding it if transmission has not begun. If Passthru is selected the unit will transmit the entire frame but will place an incorrect crc in it to preserve the error indication. (1) discard (2) passthru
Status: mandatory Access: read-write
OBJECT-TYPE    
  INTEGER discard(1), passthru(2)  

sfrapCfgFrLmiType 1.3.6.1.4.1.485.7.2.5.3
The LMI type used in a Frame Relay application. This setting must match the attached Frame Relay device configuration. Annex-A and Annex-D use DLCI 0, and Type 1 uses DLCI 1023. Type 1 is alternatively referred to as Cisco, Group of four, or simply LMI. Annex-D may be referred to as ANSI T1.617. Annex-A may be referred to as ITU or CCITT Q.933. Auto-sense will either use the most recently detected LMI type or, in the absence of any LMI, will attempt to instigate LMI communications using each protocol. (1) Annnex-A: conforms to ITU (CCITT) Q.933 annex A (2) Annnex-D: conforms to ANSI T1.617 annex D (3) Type 1: conforms to the original LMI as developed by the Group of Four (4) Auto-sense: unit will attempt to detect and synchronize to the LMI type of the attached equipment.
Status: mandatory Access: read-write
OBJECT-TYPE    
  INTEGER annexd(1), annexa(2), type1(3), autosense(4)  

sfrapCfgFrLmiInactivityTimeout 1.3.6.1.4.1.485.7.2.5.4
Timer used by the unit to determine that an attached device is not participating in the LMI protocol and that the unit should attempt to source LMI. This timer also controls the length of time that the LMI sourcing state machine remains in a particular state as it attempts to locate an LMI peer. (0) LMI Sourcing disabled (2-255) LMI Inactivity timeout
Status: mandatory Access: read-write
OBJECT-TYPE    
  INTEGER 0..255  

sfrapCfgFrLmiKeepaliveTimeout 1.3.6.1.4.1.485.7.2.5.5
Timer used by the unit to determine the frequency at which Status Enquiries are issued during LMI sourcing states where the unit is emulating a Frame Relay DTE device. (2-255) length of time between sending enquiries (in seconds)
Status: mandatory Access: read-write
OBJECT-TYPE    
  INTEGER 2..255  

sfrapCfgFrAddrResMode 1.3.6.1.4.1.485.7.2.5.6
Enable ARP (2), INARP (3), both (4), or neither (1).
Status: mandatory Access: read-write
OBJECT-TYPE    
  INTEGER inactive(1), arp(2), inarp(3), both(4)  

sfrapCfgFrAddrResDlcis 1.3.6.1.4.1.485.7.2.5.9
Address Resolution Dlcis determines which dlcis are used for address resolution. The choices include using the configured management dlci only (1), all dlcis (2), all dlcis on the To-DCE port (3) or all dlcis on the To-DTE port (4). In the last two cases, the management dlci is used on the other port. Multiple DLCI support only applies to piggyback mode; in other management modes, only the configured management dlci is used.
Status: mandatory Access: read-write
OBJECT-TYPE    
  INTEGER single(1), multiple(2), todcemulti(3), todtemulti(4)  

sfrapCfgFrAddrResInarpTimer 1.3.6.1.4.1.485.7.2.5.7
The frequency of INARP requests in seconds from 5 seconds to 86400 seconds (24 hours).
Status: mandatory Access: read-write
OBJECT-TYPE    
  INTEGER 5..86400  

sfrapCfgFrLmiFullStatus 1.3.6.1.4.1.485.7.2.5.8
Timer used by the unit to determine if an LMI Full Status Report is missing. In the absence of a Full Status report for the duration defined by this timer, the unit will declared all DLCI's status INACTIVE and begin logging down time. Data passage is not interfered with. (0) Full Status Timer is disabled (20-3600) Full Status Report Timeout in seconds.
Status: mandatory Access: read-write
OBJECT-TYPE    
  INTEGER 0..3600  

sfrapCfgVnipTable 1.3.6.1.4.1.485.7.2.6
OBJECT IDENTIFIER    

sfrapCfgVnipMode 1.3.6.1.4.1.485.7.2.6.1
This setting configures the unit for VNIP topology support on a per-interface basis. Establishing a VNIP topology is a fundamental prerequisite to applying the VNIP feature set which includes PVC-based delay measurement, diagnostics, and congestion monitoring. With VNIP enabled on an interface the unit will attempt to locate VNIP peers out that port. As peers are discovered and logged the unit will report the topology it has learned on its opposite interface. If VNIP is inactive on one interface it will not engage in any VNIP dialog; however it will continue to listen for topology messages on the inactive interface and will reflect these messages out the opposite interface if VNIP is enabled. With VNIP inactive on both interfaces the unit will transparently pass all VNIP messages. The topology database includes ip addresses, DLCI values, and the number of VNIP hops in between. (1) Topology Inactive: VNIP messages pass through unit (2) Topology Enabled on TO-DTE only: unit logs VNIP peers seen out the TO-DTE interface. Unit listens for topology reports from the WAN but doesn't generate any towards the WAN. Will report learned WAN topology towards the TO-DTE. (3) Topology Enabled on WAN only: unit logs VNIP peers seen out the WAN interface. Unit listens for topology reports from the TO-DTE but doesn't generate any towards the TO-DTE. Will report learned TO-DTE topology towards the WAN. (4) Topolgy Enabled on Both TO-DTE and WAN: Unit logs VNIP peers seen out both interfaces and generates TO-DTE topolgy reports towards the WAN and vice versa.
Status: mandatory Access: read-write
OBJECT-TYPE    
  INTEGER inactive(1), to-dte(2), to-dce(3), both(4)  

sfrapCfgVnipInitTimer 1.3.6.1.4.1.485.7.2.6.2
VNIP peer to peer communications are initiated following the detection of a VNIP Hello message. The unit will periodically issue this message out interfaces that have VNIP enabled until a Hello response is received. Following the reception of the Hello response, the unit will stop issuing Hello messahges on that DLCI/interface and generate periodic topology reports at the VNIP Keep Alive frequency. The unit will generate periodic Hello messages, at the InitTimer frequency if no Hello responses are ever detected or a topology message not been detected within the time period defined by the VNIP Inactivity timer. (5-86400) VNIP Hello frequency (in seconds)
Status: mandatory Access: read-write
OBJECT-TYPE    
  INTEGER 5..86400  

sfrapCfgVnipTxTimer 1.3.6.1.4.1.485.7.2.6.3
The frequency of hello messages sent to neighbor(s) in seconds from 5 seconds to 86400 seconds (24 hours).
Status: mandatory Access: read-write
OBJECT-TYPE    
  INTEGER 5..86400  

sfrapCfgVnipRxTimer 1.3.6.1.4.1.485.7.2.6.4
The timeout on receiving a hello message from a neighbor in seconds from 5 seconds to 86400 seconds (24 hours).
Status: mandatory Access: read-write
OBJECT-TYPE    
  INTEGER 5..86400  

sfrapCfgVnipTransitDelayFrequency 1.3.6.1.4.1.485.7.2.6.5
Transit Delay measurements may be enabled between any DLCI peers that have been logged through the topology protocol. Delay messages are issued at this frequency and results are recorded. Transit delay measures the round-trip network delay between two VNIP peers (internal unit latencies are not part of the measurement). Traps may be optionally generated if a delay threshold is exceeded. (15-86400): Transit Delay message frequency (in seconds)
Status: mandatory Access: read-write
OBJECT-TYPE    
  INTEGER 15..86400  

sfrapCfgTransitDelayTable 1.3.6.1.4.1.485.7.2.6.20
The table defining the transit delay measurement profile for each of the learned VNIP peers. As peers are located and logged into the topology database, a default transit delay profile is assumed. The default is to enable transit delay to all hops located out the interface. A DLCI's transit delay profile cannot be modified unless the DLCI has been discovered through the VNIP topology protocol.
Status: mandatory Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    SfrapCfgTransitDelayEntry

sfrapCfgTransitDelayEntry 1.3.6.1.4.1.485.7.2.6.20.1
A VNIP Transit Delay configuration entry for a particular DLCI on a particular interface. A DLCI's transit delay profile cannot be modified unless the DLCI has been discovered through the VNIP topology protocol
Status: mandatory Access: not-accessible
OBJECT-TYPE    
  SfrapCfgTransitDelayEntry  

sfrapCfgTransitDelayInterface 1.3.6.1.4.1.485.7.2.6.20.1.1
The interface being configured for VNIP Transit Delay, either to-dte-interface (1) or to-dce-interface (2). This table is indexed by {interface,dlci}.
Status: mandatory Access: read-write
OBJECT-TYPE    
  INTEGER to-dte-interface(1), to-dce-interface(2)  

sfrapCfgTransitDelayDlciValue 1.3.6.1.4.1.485.7.2.6.20.1.2
This is the DLCI being configured for VNIP Transit Delay. If topology is enabled, each interface will contain a database of VNIP peers organized by DLCI value and Number of Hops.
Status: mandatory Access: read-write
OBJECT-TYPE    
  INTEGER  

sfrapCfgTransitDelayNumHops 1.3.6.1.4.1.485.7.2.6.20.1.4
VNIP topolgy may include multiple units on a given DLCI/interface. The topology logs the number of intermediate VNIP peers between units (Hops). This setting determines which peers on a DLCI are participating in delay measurements. (0) All hops (1-254) individually addressable delay measurement between any two peers. (255) Furthest hop only
Status: mandatory Access: read-write
OBJECT-TYPE    
  INTEGER 0..255  

sfrapCfgTransitDelayRcvSummaryCancel 1.3.6.1.4.1.485.7.2.6.20.1.5
Controls the Receive Summary Cancellation feature of VNIP Transit Delay on this interface/DLCI. Every Transit Delay measurement exchange includes a follow-up message from the initiator with the delay results. If RSC is enabled, a unit will log results based upon this summary message and will not issue its next scheduled delay measurement. With RSC disabled, the unit will not use the summary message and will always issue its regularly scheduled message based on the delay frequency timer. The purpose of this feature is to reduce traffic introduced by VNIP. In a typical peer-to-peer transit delay measurement where both ends are concurrently conducting transit delay measurements it's recommended that one end have RSC enabled and one end disabled.
Status: mandatory Access: read-write
OBJECT-TYPE    
  INTEGER enable-rsc(1), disable-rsc(2)  

sfrapCfgTransitDelayThreshold 1.3.6.1.4.1.485.7.2.6.20.1.6
Specifies a transit delay threshold for this DLCI/interface. When the transit delay exceeds the threshold, a TRAP is sent. The threshold may be set from one millisecond to 24 hours. A value of 0 will prevent a TRAP from being sent. (0): Transit delay threshold trap disabled for this DLCI/interface (1-86400000): delay threshhold. Any delay measurements exceeding this result will generate a trap.
Status: mandatory Access: read-write
OBJECT-TYPE    
  INTEGER 0..86400000  

sfrapCfgTDDeleteTable 1.3.6.1.4.1.485.7.2.6.21
The table allows the user to disable transit delay measurements for a specific DLCI on a particular interface.
Status: mandatory Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    SfrapCfgTDDeleteEntry

sfrapCfgTDDeleteEntry 1.3.6.1.4.1.485.7.2.6.21.1
Disables VNIP Transit Delay for a particular interface and DLCI.
Status: mandatory Access: not-accessible
OBJECT-TYPE    
  SfrapCfgTDDeleteEntry  

sfrapCfgTDDeleteInterface 1.3.6.1.4.1.485.7.2.6.21.1.1
Transit delay can be disabled for a given DLCI on either interface. This indexes the interface. Setting this index and the associated DLCI index will disable transit delay on that combination.
Status: mandatory Access: not-accessible
OBJECT-TYPE    
  INTEGER to-dte-interface(1), to-dce-interface(2)  

sfrapCfgTDDeleteDlciValue 1.3.6.1.4.1.485.7.2.6.21.1.2
The DLCI chosen to be deleted from the specified interface-side of the VNIP Transit Delay configuration table. This table is indexed by {interface}. To delete an entry in the sfrapCfgTransitDelayTable, specify the interface as the index and set the dlci.
Status: mandatory Access: write-only
OBJECT-TYPE    
  INTEGER  

sfrapCfgTransitDelayTableClear 1.3.6.1.4.1.485.7.2.6.22
The sfrapCfgTransitDelayTable is cleared. (1) clear the table
Status: mandatory Access: write-only
OBJECT-TYPE    
  INTEGER clear-table(1)  

sfrapCfgFrPerf 1.3.6.1.4.1.485.7.2.7
OBJECT IDENTIFIER    

sfrapCfgFrPerfDlciNamesTable 1.3.6.1.4.1.485.7.2.7.1
This table allows the user to configure DLCI specific parameters such as Names, CIR, and EIR. Additionally, any DLCIs configured with these parameters will be added into the Short Term statistics database next time its cleared.
Status: mandatory Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    SfrapCfgFrPerfDlciNamesEntry

sfrapCfgFrPerfDlciNamesEntry 1.3.6.1.4.1.485.7.2.7.1.1
A table entry indexed by DLCI, containing a DLCI, a DLCI name, a CIR, and how the CIR value was obtained.
Status: mandatory Access: not-accessible
OBJECT-TYPE    
  SfrapCfgFrPerfDlciNamesEntry  

sfrapCfgFrPerfDlciNamesDlciValue 1.3.6.1.4.1.485.7.2.7.1.1.1
A DLCI selected for customized configuration and to be added to short term statistics collection (if it wasn't already there).
Status: mandatory Access: read-write
OBJECT-TYPE    
  INTEGER  

sfrapCfgFrPerfDlciNamesDlciName 1.3.6.1.4.1.485.7.2.7.1.1.2
A user-specifiable name for an individual DLCI.
Status: mandatory Access: read-write
OBJECT-TYPE    
  DisplayString Size(0..15)  

sfrapCfgFrPerfDlciNamesCirValue 1.3.6.1.4.1.485.7.2.7.1.1.3
The CIR value for an individual DLCI. This value is used in the calculation utilization as a percentage of CIR. If the CIR is reported in the LMI message then the reported value will override this configured entry. In the absence of LMI CIR and a configured CIR, the unit will assume that teh CIR is the DTE Line Rate.
Status: mandatory Access: read-write
OBJECT-TYPE    
  INTEGER  

sfrapCfgFrPerfDlciNamesCirType 1.3.6.1.4.1.485.7.2.7.1.1.4
The source of the CIR value for this DLCI. If CIR for a DLCI is part of the LMI message then this LMI supplied CIR will override any defined CIR. If CIR is not part of LMI and has not been explicitly defined by the user it will default to the TO-DTE Line Rate. (1) CIR reported in LMI Full Status message (2) CIR configured by user (3) CIR defaulted to TO-DTE Line Rate
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER cir-acquired-from-lmi(1), cir-configured-by-user(2), cir-is-datarate(3)  

sfrapCfgFrPerfDlciNamesUtilThreshold 1.3.6.1.4.1.485.7.2.7.1.1.5
The threshold for generating a utilization threshold trap as a percentage of the CIR. If the utilization percentage is above this threshold for more than sfrapCfgFrPerfDlciUtilThreshold number of sfrapCfgFrPerfTimersSTInterval's a sfrapPvc(Rx/Tx)UtilizationExceeded trap will be issued. If the If the utilization percentage falls below this threshold for more than sfrapCfgFrPerfDlciUtilThreshold number of sfrapCfgFrPerfTimersSTInterval's a sfrapPvc(Rx/Tx)UtilizationExceeded trap will be issued.
Status: mandatory Access: read-write
OBJECT-TYPE    
  INTEGER 0..100  

sfrapCfgFrPerfDlciNamesEirValue 1.3.6.1.4.1.485.7.2.7.1.1.6
The EIR value for an individual DLCI. In the absence of a configured EIR, the unit will assume that the EIR is the DTE Line Rate.
Status: mandatory Access: read-write
OBJECT-TYPE    
  INTEGER  

sfrapCfgFrPerfDlciNamesDelete 1.3.6.1.4.1.485.7.2.7.2
Setting this object with a specific DLCI value will remove the DLCI form the DLCI-specific parameters database.
Status: mandatory Access: write-only
OBJECT-TYPE    
  INTEGER  

sfrapCfgFrPerfTimers 1.3.6.1.4.1.485.7.2.7.3
OBJECT IDENTIFIER    

sfrapCfgFrPerfTimersSTInterval 1.3.6.1.4.1.485.7.2.7.3.1
The interval in seconds to collect short term statistics before moving the current counts into the previous counts and starting current from zeros. The range is 3 to 60 seconds.
Status: mandatory Access: read-write
OBJECT-TYPE    
  INTEGER 3..60  

sfrapCfgFrPerfTimersLTInterval 1.3.6.1.4.1.485.7.2.7.3.2
Long term statistics maintain 96 contiguous intervals of configurable protocol per DLCI statistics. This value is the window size of each interval. Adjusting this value will change the overall length of time that the 96 intervals will span. (4-3600): long term statsistics collection interval
Status: mandatory Access: read-write
OBJECT-TYPE    
  INTEGER 4..3600  

sfrapCfgFrPerfUserProtocolsTable 1.3.6.1.4.1.485.7.2.7.4
This table allows the user to select TCP/UDP ports for statistics collection. Tx and Rx byte counts will collected on the specified ports. These ports are selectable as protocols in the long term statistics filter and are displayed with the other protocols in the short term statistics.
Status: mandatory Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    SfrapCfgFrPerfUserProtocolsEntry

sfrapCfgFrPerfUserProtocolsEntry 1.3.6.1.4.1.485.7.2.7.4.1
An index and TCP/UDP port number pair.
Status: mandatory Access: not-accessible
OBJECT-TYPE    
  SfrapCfgFrPerfUserProtocolsEntry  

sfrapCfgFrPerfUserProtocolsIndex 1.3.6.1.4.1.485.7.2.7.4.1.1
An index. Beginning with index 1, the range is defined in SysNumUserProtocols
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER  

sfrapCfgFrPerfUserProtocolsPortNum 1.3.6.1.4.1.485.7.2.7.4.1.2
Tx and Rx byte counts will be collected on the user-specifiable TCP/UDP port number. (0) port not defined (1-65535): IP TCP/UDP protocol port number.
Status: mandatory Access: read-write
OBJECT-TYPE    
  INTEGER  

sfrapCfgFrPerfLTDlciFilterTable 1.3.6.1.4.1.485.7.2.7.5
Long term statistics can only be collected on a limited number of DLCIs. The value of SysLTFNumDlcis defines the maximum number of DLCIs that can be included in the Long Term Statistics. Once one or more DLCIs are added to Long Term Stats, the user may assign a set of protocols that will be monitored across all of the Long Term DLCIs.
Status: mandatory Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    SfrapCfgFrPerfLTDlciFilterEntry

sfrapCfgFrPerfLTDlciFilterEntry 1.3.6.1.4.1.485.7.2.7.5.1
An index and DLCI number pair.
Status: mandatory Access: not-accessible
OBJECT-TYPE    
  SfrapCfgFrPerfLTDlciFilterEntry  

sfrapCfgFrPerfLTDlciFilterIndex 1.3.6.1.4.1.485.7.2.7.5.1.1
An index. Beginning with index 1, the maximum is defined by the value of SysLTFNumDlcis.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER  

sfrapCfgFrPerfLTDlciFilterDlciNum 1.3.6.1.4.1.485.7.2.7.5.1.2
Setting a DLCI value here will add that DLCI into the Long term statistics database (associated with its index) and it will be monitored for the protocol activity defined in the Long Term Protocol filter.
Status: mandatory Access: read-write
OBJECT-TYPE    
  INTEGER  

sfrapCfgFrPerfLTProtocolFilterTable 1.3.6.1.4.1.485.7.2.7.6
Long term statistics can only be collected on a limited number of protocols. The maximum number of Long Term Protoocls are defined by SysLTFNumProtocols. This table allows the user to configure those protocols.
Status: mandatory Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    SfrapCfgFrPerfLTProtocolFilterEntry

sfrapCfgFrPerfLTProtocolFilterEntry 1.3.6.1.4.1.485.7.2.7.6.1
An index and protocol pair.
Status: mandatory Access: not-accessible
OBJECT-TYPE    
  SfrapCfgFrPerfLTProtocolFilterEntry  

sfrapCfgFrPerfLTProtocolFilterIndex 1.3.6.1.4.1.485.7.2.7.6.1.1
An index. Beginning with index 1, the maximum is defined by the value of SysLTFNumProtocols.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER  

sfrapCfgFrPerfLTProtocolFilterProtocol 1.3.6.1.4.1.485.7.2.7.6.1.2
Long term statistics will be collected on the user-specifiable protocol. Setting a -1 remove the indexed protocol from the filter.
Status: mandatory Access: read-write
OBJECT-TYPE    
  INTEGER ip-tx-bc(1), ip-rx-bc(2), tcp-ip-tx-bc(3), tcp-ip-rx-bc(4), ftp-tcp-ip-tx-bc(5), ftp-tcp-ip-rx-bc(6), telnet-tcp-ip-tx-bc(7), telnet-tcp-ip-rx-bc(8), smtp-tcp-ip-tx-bc(9), smtp-tcp-ip-rx-bc(10), http-tcp-ip-tx-bc(13), http-tcp-ip-rx-bc(14), netbios-ssn-tcp-ip-tx-bc(15), netbios-ssn-tcp-ip-rx-bc(16), udp-ip-tx-bc(21), udp-ip-rx-bc(22), tftp-udp-ip-tx-bc(29), tftp-udp-ip-rx-bc(30), netbios-dgm-udp-ip-tx-bc(33), netbios-dgm-udp-ip-rx-bc(34), snmp-udp-ip-tx-bc(35), snmp-udp-ip-rx-bc(36), snmptrap-udp-ip-tx-bc(37), snmptrap-udp-ip-rx-bc(38), rip-udp-ip-tx-bc(39), rip-udp-ip-rx-bc(40), icmp-ip-tx-bc(41), icmp-ip-rx-bc(42), echorep-icmp-ip-tx-bc(43), echorep-icmp-ip-rx-bc(44), dest-unr-icmp-ip-tx-bc(45), dest-unr-icmp-ip-rx-bc(46), src-quench-icmp-ip-tx-bc(47), src-quench-icmp-ip-rx-bc(48), redirect-icmp-ip-tx-bc(49), redirect-icmp-ip-rx-bc(50), echoreq-icmp-ip-tx-bc(51), echoreq-icmp-ip-rx-bc(52), time-excd-icmp-ip-tx-bc(53), time-excd-icmp-ip-rx-bc(54), param-prob-icmp-ip-tx-bc(55), param-prob-icmp-ip-rx-bc(56), timestamp-req-icmp-ip-tx-bc(57), timestamp-req-icmp-ip-rx-bc(58), timestamp-rep-icmp-ip-tx-bc(59), timestamp-rep-icmp-ip-rx-bc(60), addr-mask-req-icmp-ip-tx-bc(61), addr-mask-req-icmp-ip-rx-bc(62), addr-mask-rep-icmp-ip-tx-bc(63), addr-mask-rep-icmp-ip-rx-bc(64), pkt-too-big-icmp-ip-tx-bc(65), pkt-too-big-icmp-ip-rx-bc(66), gp-mem-query-icmp-ip-tx-bc(67), gp-mem-query-icmp-ip-rx-bc(68), gp-mem-report-icmp-ip-tx-bc(69), gp-mem-report-icmp-ip-rx-bc(70), gp-mem-reduct-icmp-ip-tx-bc(71), gp-mem-reduct-icmp-ip-rx-bc(72), ospf-ip-tx-bc(73), ospf-ip-rx-bc(74), other-ip-tx-bc(75), other-ip-rx-bc(76), ipx-tx-bc(77), ipx-rx-bc(78), spx-ipx-tx-bc(79), spx-ipx-rx-bc(80), ncp-ipx-tx-bc(81), ncp-ipx-rx-bc(82), sap-ipx-tx-bc(83), sap-ipx-rx-bc(84), rip-ipx-tx-bc(85), rip-ipx-rx-bc(86), netbios-ipx-tx-bc(87), netbios-ipx-rx-bc(88), other-ipx-tx-bc(89), other-ipx-rx-bc(90), arp-tx-bc(91), arp-rx-bc(92), arp-req-tx-bc(93), arp-req-rx-bc(94), arp-rep-tx-bc(95), arp-rep-rx-bc(96), rarp-req-tx-bc(97), rarp-req-rx-bc(98), rarp-rep-tx-bc(99), rarp-rep-rx-bc(100), inarp-req-tx-bc(101), inarp-req-rx-bc(102), inarp-rep-tx-bc(103), inarp-rep-rx-bc(104), sna-tx-bc(105), sna-rx-bc(106), sna-subarea-tx-bc(107), sna-subarea-rx-bc(108), sna-periph-tx-bc(109), sna-periph-rx-bc(110), sna-appn-tx-bc(111), sna-appn-rx-bc(112), sna-netbios-tx-bc(113), sna-netbios-rx-bc(114), cisco-tx-bc(115), cisco-rx-bc(116), other-tx-bc(117), other-rx-bc(118), user-defined-1-tx-bc(119), user-defined-1-rx-bc(120), user-defined-2-tx-bc(121), user-defined-2-rx-bc(122), user-defined-3-tx-bc(123), user-defined-3-rx-bc(124), user-defined-4-tx-bc(125), user-defined-4-rx-bc(126), thru-byte-tx-bc(127), thru-byte-rx-bc(128), thru-frame-tx-c(129), thru-frame-rx-c(130), thru-fecn-tx-c(131), thru-fecn-rx-c(132), thru-becn-tx-c(133), thru-becn-rx-c(134), thru-de-tx-c(135), thru-de-rx-c(136), cir-percent-range1-tx-bc(137), cir-percent-range1-rx-bc(138), cir-percent-range2-tx-bc(139), cir-percent-range2-rx-bc(140), cir-percent-range3-tx-bc(141), cir-percent-range3-rx-bc(142), cir-percent-range4-tx-bc(143), cir-percent-range4-rx-bc(144), cir-percent-range5-tx-bc(145), cir-percent-range5-rx-bc(146), cir-percent-range6-tx-bc(147), cir-percent-range6-rx-bc(148), cir-percent-range7-tx-bc(149), cir-percent-range7-rx-bc(150), cir-percent-range8-tx-bc(151), cir-percent-range8-rx-bc(152), lmi-tx-bc(153), lmi-rx-bc(154), lmi-livo-enq-tx-bc(155), lmi-livo-enq-rx-bc(156), lmi-livo-stat-tx-bc(157), lmi-livo-stat-rx-bc(158), lmi-full-enq-tx-bc(159), lmi-full-enq-rx-bc(160), lmi-full-stat-tx-bc(161), lmi-full-stat-rx-bc(162), lmi-other-tx-bc(163), lmi-other-rx-bc(164), total-uptime(165), total-downtime(166), igrp-tx-bc(167), igrp-rx-bc(168), vnip-tx-bc(169), vnip-rx-bc(170), annex-g-tx-bc(171), annex-g-rx-bc(172), delete-entry(-1)  

sfrapCfgFrPerfDlciDefaultUtilThreshold 1.3.6.1.4.1.485.7.2.7.7
The default threshold for generating a utilization threshold trap as a percentage of the CIR. This value is used for sfrapCfgFrPerfDlciNamesUtilThreshold when a DLCI is first discovered.
Status: mandatory Access: read-write
OBJECT-TYPE    
  INTEGER 0..100  

sfrapCfgFrPerfDlciUtilDuration 1.3.6.1.4.1.485.7.2.7.8
The number of Short Term Intervals that a DLCI's utilization as a percentage of CIR must be above or below the value of sfrapCfgFrPerfDlciUtilThreshold before a sfrapPvc(Rx/Tx)UtilizationExceededTrap or sfrapPvc(Rx/Tx)UtilizationClearedTrap is issued.
Status: mandatory Access: read-write
OBJECT-TYPE    
  INTEGER 0..65535  

sfrapCfgFrPerfDlciNamesTableClear 1.3.6.1.4.1.485.7.2.7.9
Clears the smperCfgFrPerfDlciNamesTable (1) clear the table or (2) clear the table but don't remove the dlcis from the short term statistics.
Status: mandatory Access: write-only
OBJECT-TYPE    
  INTEGER clear-table(1), clear-table-keep-stats(2)  

sfrapCfgFrPerfUserProtocolsTableClear 1.3.6.1.4.1.485.7.2.7.10
Clears the sfrapCfgFrPerfUserProtocolsTable (1) clear the table
Status: mandatory Access: write-only
OBJECT-TYPE    
  INTEGER clear-table(1)  

sfrapCfgFrPerfLTDlciFilterTableClear 1.3.6.1.4.1.485.7.2.7.11
Clears the sfrapCfgFrPerfLTDlciFilterTable (1) clear the table
Status: mandatory Access: write-only
OBJECT-TYPE    
  INTEGER clear-table(1)  

sfrapCfgFrPerfLTProtocolFilterTableClear 1.3.6.1.4.1.485.7.2.7.12
Clears the sfrapCfgFrPerfLTProtocolFilterTable (1) clear the table
Status: mandatory Access: write-only
OBJECT-TYPE    
  INTEGER clear-table(1)  

sfrapCfgFrPerfUnprovDlcisDelete 1.3.6.1.4.1.485.7.2.7.13
Delete all unprovisioned and Not-In-LMI dlcis (1) delete all unprovisioned
Status: mandatory Access: write-only
OBJECT-TYPE    
  INTEGER delete-unprov(1)  

sfrapCfgSecurityTable 1.3.6.1.4.1.485.7.2.8
OBJECT IDENTIFIER    

sfrapCfgTelnetCliPassword 1.3.6.1.4.1.485.7.2.8.1
The password needed to start a CLI (Command Line Interface) session using either a terminal connected to the unit or Telnet.
Status: mandatory Access: read-write
OBJECT-TYPE    
  DisplayString Size(0..8)  

sfrapCfgTftpPassword 1.3.6.1.4.1.485.7.2.8.2
The password needed to initiate a TFTP download.
Status: mandatory Access: read-write
OBJECT-TYPE    
  DisplayString Size(0..8)  

sfrapCfgCliPassword 1.3.6.1.4.1.485.7.2.8.3
OBSOLETE: The Telnet and CLI passwords are one and the same. Use the above sfrapCfgTelnetCliLcdPassword to log into the CLI (Command Line Interface).
Status: mandatory Access: read-write
OBJECT-TYPE    
  DisplayString Size(0..8)  

sfrapCfgGetCommunityString 1.3.6.1.4.1.485.7.2.8.5
The community string for doing SNMP GETs. The unit will respond to GETs that use either this string or the SET community string. All others will be rejected and a trap will be generated. String is case sensitive.
Status: mandatory Access: read-write
OBJECT-TYPE    
  DisplayString Size(0..15)  

sfrapCfgSetCommunityString 1.3.6.1.4.1.485.7.2.8.6
The community string for doing SNMP SETs. The unit will reject SETs with any other coimmunity string and will generate a trap. String is case sensitive.
Status: mandatory Access: read-write
OBJECT-TYPE    
  DisplayString Size(0..15)  

sfrapCfgLock 1.3.6.1.4.1.485.7.2.12
Request to start configuration download and lock out any other means of configuring the unit. The integer passed in represents the time out period in seconds between sets. A set to this object will fail if the unit is already in a configuration locked state.
Status: mandatory Access: write-only
OBJECT-TYPE    
  INTEGER 1..600  

sfrapCfgLockID 1.3.6.1.4.1.485.7.2.13
Returns the IP Address of the management station currently in control of configuration. A unit that is not in a configuration locked state will return 0.0.0.0
Status: mandatory Access: read-only
OBJECT-TYPE    
  IpAddress  

sfrapCfgID 1.3.6.1.4.1.485.7.2.14
A read of this object returns the Current Configuration ID string. A write sets the Configuration ID string. The string contains a starting character to indicate the last configuration source C = Envisage N = CLI/TELNET L = LCD S= other SNMP management station and a unique 7 integer value to differentiate configurations between common sources. A value of *STARTUP indicates the configuration has been defaulted. A write will only be accepted from the management station that has successfully obtained the configuration lock
Status: mandatory Access: read-write
OBJECT-TYPE    
  DisplayString Size(0..8)  

sfrapCfgStatus 1.3.6.1.4.1.485.7.2.15
The status of a configuration install is reported here. On startup, a status of success will be reported. (1) The configuration has been locked and an update or unlock command has not been received. (2) An update command has been received and the configuration has been validated as consistent; . (3) An update command has been received but the DTE port datarate is not compatible with the density. (4) An update command has been received but the number of channels to be allocated will not fit in the available channels. (5) An update command has been received but there is an error in the configuration that is not a datarate-density-conflict or bandwidth-allocation-error. (6) The time between consecutive set requests exceeded the timeout sent with the sfrapCfgLock command. (7) The user sent a sfrapCfgUnlock command before a sfrapCfgUpdate command. This usually means that one of the sets in the configuration failed.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER in-progress(1), success(2), datarate-density-conflict(3), bandwidth-allocation-error(4), general-error(5), timeout(6), aborted-by-user(7)  

sfrapCfgUnlock 1.3.6.1.4.1.485.7.2.16
The management station sets this variable to complete the configuration install process. Un-lock (1) notifies the agent to remove the lock on configuring the unit without updating the configuration.
Status: mandatory Access: write-only
OBJECT-TYPE    
  INTEGER un-lock(1)  

sfrapCfgUpdate 1.3.6.1.4.1.485.7.2.17
The management station sets this variable to complete the configuration install process. Update (1) notifies the agent to start the update process within the unit.
Status: mandatory Access: write-only
OBJECT-TYPE    
  INTEGER update(1)  

sfrapDiagnostics 1.3.6.1.4.1.485.7.3
OBJECT IDENTIFIER    

sfrapDiagUnitTable 1.3.6.1.4.1.485.7.3.1
OBJECT IDENTIFIER    

sfrapDiagUnitLocLoop 1.3.6.1.4.1.485.7.3.1.1
Controls a bi-directional unit loopback. Data is received from either interface, processed, and transmitted back towards the same interface. When configured for Frame Relay operation the unit will preserve the LMI path and maintain managed access during this loopback. In Frame Relay mode, only valid HDLC frames are looped back (pseudorandom test patterns will be dropped). (1) enable unit loopback (2) disable unit loopback
Status: mandatory Access: read-write
OBJECT-TYPE    
  INTEGER enable-loopback-mode(1), disable-loopback-mode(2)  

sfrapDiagUnitReset 1.3.6.1.4.1.485.7.3.1.2
Enables the operator to remotely reset the unit. Using this command will cause the unit to terminate all its connections and drop data.
Status: mandatory Access: write-only
OBJECT-TYPE    
  INTEGER reset-unit(1)  

sfrapDiagUnitTimeRemaining 1.3.6.1.4.1.485.7.3.1.3
The remaining time on the active loopback before the loopback times out. The time is in hundredths of seconds (TimeTicks).
Status: mandatory Access: read-only
OBJECT-TYPE    
  TimeTicks  

sfrapDiagUnitCutThru 1.3.6.1.4.1.485.7.3.1.4
Enables the operator to control and examine the UNIT Cut Through mode. This diagnostic occurs on the TO-DTE and TO-DCE transmit and receive logic. The unit will transmit To-DTE data onto the TO-DCE port without any intervention by the processor. If the CutThruTimeout is greater than 0, then the cut-thru diagnostic will time out after that interval (in minutes). (same as Tap Mode operation - see CfgAppOperationMode).
Status: mandatory Access: read-write
OBJECT-TYPE    
  INTEGER enable-cutthru-mode(1), disable-cutthru-mode(2)  

sfrapDiagUnitCutThruTimeRemaining 1.3.6.1.4.1.485.7.3.1.5
The remaining time on the active loopback before the loopback times out. The time is in hundredths of seconds (TimeTicks).
Status: mandatory Access: read-only
OBJECT-TYPE    
  TimeTicks  

sfrapDiagDteTable 1.3.6.1.4.1.485.7.3.3
The table of DTE port diagnostics.
Status: mandatory Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    SfrapDiagDteEntry

sfrapDiagDteEntry 1.3.6.1.4.1.485.7.3.3.1
An diagnostic entry for a DTE port.
Status: mandatory Access: not-accessible
OBJECT-TYPE    
  SfrapDiagDteEntry  

sfrapDiagDteIndex 1.3.6.1.4.1.485.7.3.3.1.99
Selects which DTE port.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER to-dte(1), to-dce(2)  

sfrapDiagDteLclLpbk 1.3.6.1.4.1.485.7.3.3.1.3
Controls the DTE loopback state. This is a bi-directional loopback state where both the DTE and WAN ports are placed in line loopback. All data received on each interface is sent back out the respective interface regardless of format or content. In Frame Relay applications the unit will not preserve the LMI path during this diagnostic and in-band management will not operate. (1) enable payload loopback (2) disable payload loopback
Status: mandatory Access: read-write
OBJECT-TYPE    
  INTEGER enable-loopback-mode(1), disable-loopback-mode(2)  

sfrapDiagDteTimeRemaining 1.3.6.1.4.1.485.7.3.3.1.13
The remaining time on the active loopback before the loopback times out and disables itself. The time is in hundredths of seconds (TimeTicks).
Status: mandatory Access: read-only
OBJECT-TYPE    
  TimeTicks  

sfrapDiagVnipTable 1.3.6.1.4.1.485.7.3.6
Table of Diagnostics performed with the VNIP protocol
Status: mandatory Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    SFRAPDiagVnipEntry

sfrapDiagVnipEntry 1.3.6.1.4.1.485.7.3.6.1
VNIP VLOOP and VBERT diagnostic profile. Initiating these tests require an established and stable VNIP topology on an interface. Once the topology is in place, the user can execute a PVC-based diagnostic between this unit and any indexed entry in the topology table. The index into the topology table for a particular interface is required.
Status: mandatory Access: not-accessible
OBJECT-TYPE    
  SFRAPDiagVnipEntry  

sfrapDiagVnipInterface 1.3.6.1.4.1.485.7.3.6.1.1
The interface out which a PVC-based VNIP diagnostic will be run. This must be an interface with a valid and stable VNIP topology for a VNIP Diagnostic.
Status: mandatory Access: read-write
OBJECT-TYPE    
  INTEGER dte-interface(1), t1-interface(2)  

sfrapDiagVnipIndex 1.3.6.1.4.1.485.7.3.6.1.2
The index to the external VNIP peer as presented by the VNIP topology database for the given interface. Refer to VnipTopologyTable to determine the index of the remote peer.
Status: mandatory Access: read-write
OBJECT-TYPE    
  INTEGER  

sfrapDiagVnipDlci 1.3.6.1.4.1.485.7.3.6.1.3
This is the DLCI value for the given interface/index combination. This comes from the VniptTopologyTable.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER  

sfrapDiagVnipIpAddr 1.3.6.1.4.1.485.7.3.6.1.4
This is the ip address for the given interface/index combination. This comes from the VniptTopologyTable.
Status: mandatory Access: read-only
OBJECT-TYPE    
  IpAddress  

sfrapDiagVLOOP 1.3.6.1.4.1.485.7.3.6.1.5
Controls execution of the Vnip Logical Loopback (VLOOP) test. VLOOP is designed as an intrusive test and customer data on the DLCI-under-test will be discarded. The VLOOP test includes a timed VBERT test and is run using the profile configured within this table. (1) start VLOOP test (2) stop VLOOP test (override VBERT test duration)
Status: mandatory Access: write-only
OBJECT-TYPE    
  INTEGER start-test(1), stop-test(2)  

sfrapDiagVBERT 1.3.6.1.4.1.485.7.3.6.1.6
Controls execution of the Vnip Virtual Bit Eror Rate (VBERT) test. VBERT is designed to be a non-intrusive test and will attempt to statistically multiplex VBERT test data and customer data on the DLCI-under-test. However, VBERT data is given priority over customer data when the selected VBERT volume causes internal congestion. The test is run using the profile configured within this table. (1) start test (2) stop test (override VBERT test duration)
Status: mandatory Access: write-only
OBJECT-TYPE    
  INTEGER start(1), stop(2)  

sfrapDiagVBERTRate 1.3.6.1.4.1.485.7.3.6.1.7
Specifies the throughput bit rate applied by VBERT or VLOOP to the DLCI-under-test. For TO-DTE Rates or configured CIR up to 64K the maximum VBERT rate is either the TO-DTE data rate or 110% of CIR (which ever is less). For TO-DTE Rates or configured CIR greater than 64K, the maximum VBERT rate is 75% of the TO-DTE data rate or 110% of CIR (which ever is less). Note that selecting rates that approach line rate will impact neighboring PVCs. (8000-1152000): VBERT/VLOOP data rate (in bits per second).
Status: mandatory Access: read-write
OBJECT-TYPE    
  INTEGER 8000..2048000  

sfrapDiagVBERTSize 1.3.6.1.4.1.485.7.3.6.1.8
Specifies the size of framed data that will be used during the VBERT test, measures in Bytes. (64) 64-byte frames (128) 128-byte frames (256) 256-byte frames (512) 512-byte frames (1024) 1024-byte frames (2048) 2048-byte frames
Status: mandatory Access: read-write
OBJECT-TYPE    
  INTEGER pkt-size-64(64), pkt-size-128(128), pkt-size-256(256), pkt-size-512(512), pkt-size-1024(1024), pkt-size-2048(2048)  

sfrapDiagVBERTPktPercent 1.3.6.1.4.1.485.7.3.6.1.9
Specifies percentage of VBERT packets that will have the Frame Relay Discard Eligibility bit set. Frames with this bit set may be more likley to get dropped in a congested network. (0) 0% of the test frames are marked discard eligible (25) 25% of the test frames are marked discard eligible (50) 50% of the test frames are marked discard eligible (75) 75% of the test frames are marked discard eligible (100) 100% of the test frames are marked discard eligible
Status: mandatory Access: read-write
OBJECT-TYPE    
  INTEGER zero-percent(0), twentyFive-percent(25), fifty-percent(50), seventyFive-percent(75), oneHundred-percent(100)  

sfrapDiagVBERTTestPeriod 1.3.6.1.4.1.485.7.3.6.1.10
Specifies the duration of a VBERT test. Note that VBERT is subjected to the unit's Loopback Timer and will be terminated by whichever timer expires first. (10-1440): VBERT time duration in seconds
Status: mandatory Access: read-write
OBJECT-TYPE    
  INTEGER 10..1440  

sfrapDiagTxClockDetect 1.3.6.1.4.1.485.7.3.7
Enables the operator to activate clock detection on the TO-DCE Transmit clock. Clock detection can be stopped by issuing the terminate command.
Status: mandatory Access: read-write
OBJECT-TYPE    
  INTEGER initiate-clock-detect(1), terminate-clock-detect(2)  

sfrapStatus 1.3.6.1.4.1.485.7.4
OBJECT IDENTIFIER    

sfrapStatusLedTable 1.3.6.1.4.1.485.7.4.4
OBJECT IDENTIFIER    

sfrapStatusLedOpStatusLED 1.3.6.1.4.1.485.7.4.4.1
Status of the Operation Mode LED.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER greenLED-high-speed-mode(1), blinkgreenLED-low-speed-mode(2), yellowLED-test-mode(3), redLED-alarm-mode(4), blinkredLED-cut-through-mode(5)  

sfrapStatusLedToDTETxLED 1.3.6.1.4.1.485.7.4.4.2
Status of the TO-DTE TxD LED.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER offLED-inactive(1), greenLED-tx-data-receiving(2)  

sfrapStatusLedToDTERxLED 1.3.6.1.4.1.485.7.4.4.3
Status of the TO-DTE RxD LED.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER offLED-inactive(1), greenLED-rx-data-receiving(2)  

sfrapStatusLedRtsLED 1.3.6.1.4.1.485.7.4.4.4
Status of the RTS Signal LED.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER greenLED-rts-active(1), offLED-rts-inactive(2)  

sfrapStatusLedCtsLED 1.3.6.1.4.1.485.7.4.4.5
Status of the CTS Signal LED.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER greenLED-cts-active(1), offLED-cts-inactive(2)  

sfrapStatusLedDsrLED 1.3.6.1.4.1.485.7.4.4.7
Status of the DSR Signal LED.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER greenLED-dsr-active(1), offLED-dsr-inactive(2)  

sfrapStatusLedDcdLED 1.3.6.1.4.1.485.7.4.4.8
Status of the DCD Signal LED.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER greenLED-dcd-active(1), offLED-dcd-inactive(2)  

sfrapStatusLedToDCETxLED 1.3.6.1.4.1.485.7.4.4.9
Status of the TO-DCE TxD LED.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER offLED-inactive(1), greenLED-tx-data-receiving(2)  

sfrapStatusLedToDCERxLED 1.3.6.1.4.1.485.7.4.4.10
Status of the TO-DCE RxD LED.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER offLED-inactive(1), greenLED-rx-data-receiving(2)  

sfrapStatusLedLmiErrLED 1.3.6.1.4.1.485.7.4.4.15
Status of the LMI Error LED.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER offLED-lmi-active-state(1), yellowLED-lmi-error-state(2), blinkyellowLED-lmi-source-state(3)  

sfrapStatusLedFrmActLED 1.3.6.1.4.1.485.7.4.4.16
Status of the Frame Activity LED.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER greenLED-frm-active(1), offLED-frm-inactive(2)  

sfrapStatusLedCtrlLED 1.3.6.1.4.1.485.7.4.4.17
Status of the X.21 Control Signal LED. Only applicable when in X.21.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER yellowLED-ctrl-active(1), offLED-ctrl-inactive(2)  

sfrapStatusLedIndLED 1.3.6.1.4.1.485.7.4.4.18
Status of the X.21 Indication Signal LED. Only applicable when in X.21.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER yellowLED-ind-active(1), offLED-ind-inactive(2)  

sfrapStatusAllLEDs 1.3.6.1.4.1.485.7.4.4.14
Status of all ten SFRAP LEDs, encoded in a string. 'F' off '5' green '0' yellow 'A' red '7' blinking green and off '3' blinking yellow and off 'B' blinking red and off '4' blinking green and yellow '6' blinking green and red '8' blinking yellow and red Positionally, the 13 letters are SFRAP Op Mode, TO-DCE Rx, TO-DCE Tx, RTS, CTS, DCD, DSR, LMI Error, Frame Activity, Ctrl, Ind, TO-DTE Rx, TO-DTE Tx.
Status: mandatory Access: read-only
OBJECT-TYPE    
  DisplayString Size(0..10)  

sfrapStatusDipswitchTable 1.3.6.1.4.1.485.7.4.10
OBJECT IDENTIFIER    

sfrapStatusDipswitchCutthru 1.3.6.1.4.1.485.7.4.10.1
Status of the Operation Mode LED.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER switch-up(1), switch-down(2), na(3)  

sfrapStatusDipswitchToDteLpbk 1.3.6.1.4.1.485.7.4.10.2
Status of the TO-DTE TxD LED.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER switch-up(1), switch-down(2), na(3)  

sfrapStatusDipswitchToDceLpbk 1.3.6.1.4.1.485.7.4.10.3
Status of the TO-DTE RxD LED.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER switch-up(1), switch-down(2), na(3)  

sfrapStatusDipswitchUnused 1.3.6.1.4.1.485.7.4.10.4
Status of the RTS Signal LED.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER switch-up(1), switch-down(2), na(3)  

sfrapStatusDipswitchIntfMode1 1.3.6.1.4.1.485.7.4.10.5
Status of the RTS Signal LED.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER switch-up(1), switch-down(2), na(3)  

sfrapStatusDipswitchIntfMode2 1.3.6.1.4.1.485.7.4.10.6
Status of the RTS Signal LED.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER switch-up(1), switch-down(2), na(3)  

sfrapStatusDteTable 1.3.6.1.4.1.485.7.4.7
The table of DTE port statuses.
Status: mandatory Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    SfrapStatusDteEntry

sfrapStatusDteEntry 1.3.6.1.4.1.485.7.4.7.1
An status entry for a DTE port.
Status: mandatory Access: not-accessible
OBJECT-TYPE    
  SfrapStatusDteEntry  

sfrapStatusDteIndex 1.3.6.1.4.1.485.7.4.7.1.99
Selects which DTE port.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER to-dte(1), to-dce(2)  

sfrapStatusDteMode 1.3.6.1.4.1.485.7.4.7.1.1
Status of the port. no-connections (1) indicates the port has no connections. Active (2) indicates connections and data mode. Test (3) indicates connections and diagnostic state for that port.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER no-connections(1), active(2), test(3)  

sfrapStatusDteRts 1.3.6.1.4.1.485.7.4.7.1.2
Status of the RTS signal on the port: on (1) and off (2).
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER on(1), off(2), na(3)  

sfrapStatusDteDtr 1.3.6.1.4.1.485.7.4.7.1.3
Status of the DTR signal on the port: on (1) and off (2).
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER on(1), off(2), na(3)  

sfrapStatusDteDcd 1.3.6.1.4.1.485.7.4.7.1.4
Whether the DCD signal on the port is on (1) or off (2).
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER on(1), off(2), na(3)  

sfrapStatusDteDsr 1.3.6.1.4.1.485.7.4.7.1.5
Whether the DSR signal on the port is on (1) or off (2).
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER on(1), off(2), na(3)  

sfrapStatusDteCts 1.3.6.1.4.1.485.7.4.7.1.6
Whether the CTS signal on the port is on (1) or off (2).
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER on(1), off(2), na(3)  

sfrapStatusDteSendtiming 1.3.6.1.4.1.485.7.4.7.1.7
Whether Send Timing is (1)present or (2)not-present on the interface.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER present(1), not-present(2), na(3)  

sfrapStatusDteRxtiming 1.3.6.1.4.1.485.7.4.7.1.8
Whether Receive Timing is (1)present or (2)not-present on the interface.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER present(1), not-present(2), na(3)  

sfrapStatusDteTermtiming 1.3.6.1.4.1.485.7.4.7.1.9
Whether Terminal Timing is (1)present or (2)not-present on the interface.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER present(1), not-present(2), na(3)  

sfrapStatusDteCtrl 1.3.6.1.4.1.485.7.4.7.1.10
The status of the Control lead when using X.21
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER on(1), off(2), na(3)  

sfrapStatusDteInd 1.3.6.1.4.1.485.7.4.7.1.11
The status of the Indication lead when using X.21
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER on(1), off(2), na(3)  

sfrapVnipTopologyTable 1.3.6.1.4.1.485.7.4.2
Topology of peers discovered via VNIP, organized by the interface (DATA1 or DATA2) from which they were discovered and an entry number or index. The topology is of limited size per interface.
Status: mandatory Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    SfrapVnipTopologyEntry

sfrapVnipTopologyEntry 1.3.6.1.4.1.485.7.4.2.1
The DLCI, IP address, and number of hops for a particular node, discovered via VNIP off of an interface (DATA1 or DATA2). The entry may also have transit delay measurements for the particular node.
Status: mandatory Access: not-accessible
OBJECT-TYPE    
  SfrapVnipTopologyEntry  

sfrapVnipTopologyInterface 1.3.6.1.4.1.485.7.4.2.1.1
The interface off of which the peer was discovered. Topology is discovered by sending VNIP messages out each interface. Nodes discovered via a particular interface are kept in a list associated with that interface.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER data1-interface(1), data2-interface(2)  

sfrapVnipTopologyIndex 1.3.6.1.4.1.485.7.4.2.1.2
The number of this discovered peer in the list of nodes for this interface. For each interface, the nodes are numbered 1 through n.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER  

sfrapVnipTopologyDlci 1.3.6.1.4.1.485.7.4.2.1.3
The DLCI of the discovered neighboring peer. This may be different from the local DLCI.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER  

sfrapVnipTopologyIpAddr 1.3.6.1.4.1.485.7.4.2.1.4
The IP address for the discovered peer.
Status: mandatory Access: read-only
OBJECT-TYPE    
  IpAddress  

sfrapVnipTopologyNumHops 1.3.6.1.4.1.485.7.4.2.1.5
The discovered peer is this number of hops away.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER  

sfrapVnipTopologyLocalDlci 1.3.6.1.4.1.485.7.4.2.1.6
The DLCI of this node over which the remote peer was discovered.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER  

sfrapVnipTopoTDNumSamples 1.3.6.1.4.1.485.7.4.2.1.10
The number of transit delay samples collected.
Status: mandatory Access: read-only
OBJECT-TYPE    
  Counter  

sfrapVnipTopoTDAvgDelay 1.3.6.1.4.1.485.7.4.2.1.11
The average transit delay between this node and the remote peer.
Status: mandatory Access: read-only
OBJECT-TYPE    
  Counter  

sfrapVnipTopoTDMaxDelay 1.3.6.1.4.1.485.7.4.2.1.12
The maximum transit delay between this node and the remote peer.
Status: mandatory Access: read-only
OBJECT-TYPE    
  Counter  

sfrapVnipTopoTDMinDelay 1.3.6.1.4.1.485.7.4.2.1.13
The minimum transit delay between this node and the remote peer.
Status: mandatory Access: read-only
OBJECT-TYPE    
  Counter  

sfrapVnipTopoTDLastDelay 1.3.6.1.4.1.485.7.4.2.1.14
The most recent transit delay measured between this node and the remote peer.
Status: mandatory Access: read-only
OBJECT-TYPE    
  Counter  

sfrapVnipTopoVLOOPStatus 1.3.6.1.4.1.485.7.4.2.1.15
This selection displays the status of the VNIP Loopback This loopback is initiated by the remote node, causing this node to loop data back to the remote node.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER loopback-enable(1), loopback-disable(2)  

sfrapVnipTopoVBERTStatus 1.3.6.1.4.1.485.7.4.2.1.16
Displays the current status of the VBERT test, values are off(1): no test has run or the entry has been cleared, testing(2): the entry is generating VBERT packets, in-test(5): the entry is on the receiving end of VBERT packets test-completed(4): a test has run and is finished results are complete test-failed(3): the request for a test on this entry failed
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER off(1), testing(2), test-failed(3), test-completed(4), in-test(5)  

sfrapVnipTopoVBertTxDESetFrames 1.3.6.1.4.1.485.7.4.2.1.17
Displays the number of Frames transmitted during VBERT Test that had the Discard Eligibility indicator bit set.
Status: mandatory Access: read-only
OBJECT-TYPE    
  Counter  

sfrapVnipTopoVBertRxDESetFrames 1.3.6.1.4.1.485.7.4.2.1.18
Displays the number of Frames received during VBERT Test that had the Discard Eligibility indicator bit set.
Status: mandatory Access: read-only
OBJECT-TYPE    
  Counter  

sfrapVnipTopoVBertTxDEClrFrames 1.3.6.1.4.1.485.7.4.2.1.19
Displays the number of Frames transmitted during VBERT Test that had the Discard Eligibility indicator bit cleared.
Status: mandatory Access: read-only
OBJECT-TYPE    
  Counter  

sfrapVnipTopoVBertRxDEClrFrames 1.3.6.1.4.1.485.7.4.2.1.20
Displays the number of Frames received during VBERT Test that had the Discard Eligibility indicator bit cleared.
Status: mandatory Access: read-only
OBJECT-TYPE    
  Counter  

sfrapVnipTopoVBertTransitDelayMax 1.3.6.1.4.1.485.7.4.2.1.21
The maximum transit delay between this node and the remote peer during the VBERT test.
Status: mandatory Access: read-only
OBJECT-TYPE    
  Counter  

sfrapVnipTopoVBertTransitDelayAvg 1.3.6.1.4.1.485.7.4.2.1.22
The average transit delay between this node and the remote peer during the VBERT test.
Status: mandatory Access: read-only
OBJECT-TYPE    
  Counter  

sfrapVnipTopoVBertTimeElapse 1.3.6.1.4.1.485.7.4.2.1.23
Elapsed time since VBERT test was started or cleared.
Status: mandatory Access: read-only
OBJECT-TYPE    
  TimeTicks  

sfrapVnipTopoVBertPerUtilCIR 1.3.6.1.4.1.485.7.4.2.1.24
The calculated percent of CIR utilization during a VBERT test, this value is only valid after a test is complete not during.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER  

sfrapVnipTopoVBertPerUtilEIR 1.3.6.1.4.1.485.7.4.2.1.25
The calculated percent of EIR utilization during a VBERT test, this value is only valid after a test is complete not during.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER  

sfrapVnipTransitDelayClear 1.3.6.1.4.1.485.7.4.5
Allows the user to clear all the VNIP Transit Delay data collected in the VNIP topology database.
Status: mandatory Access: write-only
OBJECT-TYPE    
  INTEGER clear-transit-delay(1)  

sfrapLmiSourcing 1.3.6.1.4.1.485.7.4.6
What type of LMI sourcing is being done: initializing (1), passthrough (2), emulating a user device on the To-DTE (3), emulating a user device on the To-DCE (4), emulating a network device on the To-DTE (5), emulating a network device on the To-DCE (6), disabled (7), or emulating a switch by responding to both ports (8).
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER initializing(1), passthrough(2), user-to-dte(3), user-to-dce(4), ntwk-to-dte(5), ntwk-to-dce(6), disabled(7), both-ports(8)  

sfrapVBertClear 1.3.6.1.4.1.485.7.4.11
Allows the user to clear all the VBERT data collected in the VNIP topology database as long as the entry is not in a test status.
Status: mandatory Access: write-only
OBJECT-TYPE    
  INTEGER clear-vbert(1)  

sfrapStatusMgmtTable 1.3.6.1.4.1.485.7.4.3
OBJECT IDENTIFIER    

sfrapStatusMgmtChannel 1.3.6.1.4.1.485.7.4.3.1
This is the method in which the unit is configured for SNMP management access. (1) None: SNMP management disabled (2) SLIP: out-of-band management via asynchronous Serial Line IP (3) Private DLCI: in-band management using a private DLCI that is dedicated solely to this unit's management. (4) Piggyback DLCI: in-band management using any DLCI optionally multiplexing both management and user data.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER none(1), slip(2), private-dlci(3), piggyback-dlci(4)  

sfrapStatusMgmtInterface 1.3.6.1.4.1.485.7.4.3.2
This is the port(s) on which the management traffic will appear. (1) Async Maintenance(Comm)/Console port - SLIP mode (2) Local TO-DTE interface: unit is configured for Private Local DLCI mode (3) Remote WAN Interface: unit is confiogured for Private Remote DLCI mode (4) TO-DTE and WAN Interfaces: unit is configured for either Piggyback Bidirectional mode.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER comm(1), local-to-dte(2), remote-to-dce(3), local-and-remote(4)  

sfrapStatusMgmtInterfaceStatus 1.3.6.1.4.1.485.7.4.3.3
This is the status of the port(s) on which the management traffic will appear. (1) Active: port or DLCI is configured and status is okay (2) Inactive: port or DLCI is declared out of service (3) Alarm: port or DLCI is experiencing an alarm condition that may interefere with management access
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER active(1), inactive(2), alarm(3)  

sfrapStatusMgmtDefaultDLCINo 1.3.6.1.4.1.485.7.4.3.4
This is the DLCI for the PVC that is defined for the Management port. All traffic using this DLCI in the Frame Replay packet will be destined for the InBand Management task.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER  

sfrapStatusMgmtDefaultDLCIStatus 1.3.6.1.4.1.485.7.4.3.5
This is the status of the default management DLCI. (1) not applicable: SLIP mode or management is disabled (2) DLCI Active: default DLCI is active in the LMI full status response. (3) DLCI Inactive: default DLCI is not active in the LMI full status response.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER na(1), dlci-active(2), dlci-inactive(3)  

sfrapStatusClockRate 1.3.6.1.4.1.485.7.4.8
This is the value in Kbps of the Receive Clock Frequency, for both the TO-DTE and TO-DCE ports.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER 0..2048000  

sfrapStatusToDteRxClockMode 1.3.6.1.4.1.485.7.4.9
The status of the Receive clocking mode.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER clock-normal(1), clock-invert(2), clock-auto-normal(3), clock-auto-invert(4)  

sfrapStatusLmiAutosense 1.3.6.1.4.1.485.7.4.12
This indicates the current status of LMI Auto Sensing if it's enabled. (1) Disabled: LMI is configured as Type 1, Annex-D, or Annex-A (2) Searching: unit is attempting to determine the LMI type of the attached equipment by issuing LMI messages of each LMI type and searching for responses. (3) Learned Annex-D: unit has successfully detected Annex-D LMI (ANSI T1.617 Annex D) (4) Learned Annex-A: unit has successfully detected Annex-A LMI (ITU/CCITT Q.933 Annex A) (5) Learned Type 1: unit has successfully detected Type 1 LMI (Cisco, Group of four, LMI)
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER disabled(1), searching(2), learned-annex-d(3), learned-annex-a(4), learned-type1(5)  

sfrapStatusTxClockDetect 1.3.6.1.4.1.485.7.4.13
This selection displays the status of the TO-DCE transmit clock auto detection process. (1)inactive - The Auto Detect option was not selected. (2)initiate - The Auto Detect option was selected and is initializing. (3)trying-cut-thru - The Auto Detect option is trying to verify the integrity of the TO-DCE transmit clock mode selected in Cut Through mode (4)failed-cut-thru - This mechanism has detected that the LMI integrity check has failed. (5)trying-inband-normal - The Auto Detection mechanism has set the TO-DCE Tx clock to normal timing and is performing the link integrity check, to determine if this selection is correct (6)success-inband-norm - The Auto Detection mechanism has determined that the TO-DCE Tx clock timing is successful in normal mode. (7)trying-inband-invert - The Auto Detection mechanism has determined that the TO-DCE clock mode failed using normal timing, now it has inverted the clock. (8)success-inband-invert - The mechanism has decided that the TO-DCE Tx clock needs to be inverted. (9)failed-in-band - Neither Normal or Invert timing was successful. (10)terminated - The Auto Detection mechanism has been terminated.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER inactive(1), initiate(2), trying-cut-thru(3), failed-cut-thru(4), trying-inband-norm(5), success-inband-norm(6), failed-inband-norm(7), trying-inband-invert(8), success-inband-invert(9), failed-inband(10), terminate(11)  

sfrapPerformance 1.3.6.1.4.1.485.7.5
OBJECT IDENTIFIER    

sfrapPerfMgmtIp 1.3.6.1.4.1.485.7.5.2
OBJECT IDENTIFIER    

sfrapPerfMgmtIpIFStatsTable 1.3.6.1.4.1.485.7.5.2.1
OBJECT IDENTIFIER    

sfrapPerfMgmtIpIFInOctets 1.3.6.1.4.1.485.7.5.2.1.1
The count of all octets received. Same as ifInOctets in mib-2.
Status: mandatory Access: read-only
OBJECT-TYPE    
  Counter  

sfrapPerfMgmtIpIFInErrors 1.3.6.1.4.1.485.7.5.2.1.2
The count of packets received that could not be delivered because of errors. Same as ifInErrors in mib-2.
Status: mandatory Access: read-only
OBJECT-TYPE    
  Counter  

sfrapPerfMgmtIpIFOutOctets 1.3.6.1.4.1.485.7.5.2.1.3
The count of all octets transmitted. Same as ifOutOctets in mib-2.
Status: mandatory Access: read-only
OBJECT-TYPE    
  Counter  

sfrapPerfMgmtIpIFOperStatus 1.3.6.1.4.1.485.7.5.2.1.4
The current operational state. Same as ifOperStatus in mib-2.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER up(1), down(2), testing(3)  

sfrapPerfMgmtIpIPStatsTable 1.3.6.1.4.1.485.7.5.2.2
OBJECT IDENTIFIER    

sfrapPerfMgmtIpIPInRcv 1.3.6.1.4.1.485.7.5.2.2.1
The count of all datagrams received. Same as ipInReceives in mib-2.
Status: mandatory Access: read-only
OBJECT-TYPE    
  Counter  

sfrapPerfMgmtIpIPInHdrErr 1.3.6.1.4.1.485.7.5.2.2.2
The count of datagrams received that were discarded because of errors in their IP headers. Same as ipInHdrErrors in mib-2.
Status: mandatory Access: read-only
OBJECT-TYPE    
  Counter  

sfrapPerfMgmtIpIPInAddrErr 1.3.6.1.4.1.485.7.5.2.2.3
The count of datagrams received that were discarded because unexpected or invalid IP addresses in their IP headers. Same as ipInAddrErrors in mib-2.
Status: mandatory Access: read-only
OBJECT-TYPE    
  Counter  

sfrapPerfMgmtIpIPInProtUnk 1.3.6.1.4.1.485.7.5.2.2.4
The count of datagrams received that were discarded because of unsupported protocols. Same as ipInUnknownProtos in mib-2.
Status: mandatory Access: read-only
OBJECT-TYPE    
  Counter  

sfrapPerfMgmtIpIPInDscrd 1.3.6.1.4.1.485.7.5.2.2.5
The count of datagrams received that were discarded for reasons other than a problem with the datagram. Same as ipInDiscards in mib-2.
Status: mandatory Access: read-only
OBJECT-TYPE    
  Counter  

sfrapPerfMgmtIpIPInDlvrs 1.3.6.1.4.1.485.7.5.2.2.6
The count of datagrams received that were delivered to IP client-protocols. Same as ipInDelivers in mib-2.
Status: mandatory Access: read-only
OBJECT-TYPE    
  Counter  

sfrapPerfMgmtIpIPOutRqst 1.3.6.1.4.1.485.7.5.2.2.7
The count of all outgoing datagrams originating in this node. Same as ipOutRequests in mib-2.
Status: mandatory Access: read-only
OBJECT-TYPE    
  Counter  

sfrapPerfMgmtIpIPOutDscrd 1.3.6.1.4.1.485.7.5.2.2.8
The count of outgoing datagrams that were discarded for reasons other than a problem with the datagram. Same as ipOutDiscards in mib-2.
Status: mandatory Access: read-only
OBJECT-TYPE    
  Counter  

sfrapPerfMgmtIpIPOutNoRt 1.3.6.1.4.1.485.7.5.2.2.9
The count of outgoing datagrams that were discarded because no route could be found for transmission. Same as ipOutNoRoutes in mib-2.
Status: mandatory Access: read-only
OBJECT-TYPE    
  Counter  

sfrapPerfMgmtIpICMPStatsTable 1.3.6.1.4.1.485.7.5.2.3
OBJECT IDENTIFIER    

sfrapPerfMgmtIpICMPInMsgs 1.3.6.1.4.1.485.7.5.2.3.1
The count of all ICMP messages received. Same as icmpInMsgs in mib-2.
Status: mandatory Access: read-only
OBJECT-TYPE    
  Counter  

sfrapPerfMgmtIpICMPInErrors 1.3.6.1.4.1.485.7.5.2.3.2
The count of ICMP messages received with errors. Same as icmpInErrors in mib-2.
Status: mandatory Access: read-only
OBJECT-TYPE    
  Counter  

sfrapPerfMgmtIpICMPInDestUnreachs 1.3.6.1.4.1.485.7.5.2.3.3
The count of ICMP Destination Unreachable messages received. Same as icmpInDestUnreachs in mib-2.
Status: mandatory Access: read-only
OBJECT-TYPE    
  Counter  

sfrapPerfMgmtIpICMPInTimeExcds 1.3.6.1.4.1.485.7.5.2.3.4
The count of ICMP Time Exceeded messages received. Same as icmpInTimeExcds in mib-2.
Status: mandatory Access: read-only
OBJECT-TYPE    
  Counter  

sfrapPerfMgmtIpICMPInParmProbs 1.3.6.1.4.1.485.7.5.2.3.5
The count of ICMP Parameter Problem messages received. Same as icmpInParmProbs in mib-2.
Status: mandatory Access: read-only
OBJECT-TYPE    
  Counter  

sfrapPerfMgmtIpICMPInRedirects 1.3.6.1.4.1.485.7.5.2.3.6
The count of ICMP Redirect messages received. Same as icmpInRedirects in mib-2.
Status: mandatory Access: read-only
OBJECT-TYPE    
  Counter  

sfrapPerfMgmtIpICMPInEchos 1.3.6.1.4.1.485.7.5.2.3.7
The count of ICMP Echo messages received. Same as icmpInEchos in mib-2.
Status: mandatory Access: read-only
OBJECT-TYPE    
  Counter  

sfrapPerfMgmtIpICMPInEchoReps 1.3.6.1.4.1.485.7.5.2.3.8
The count of ICMP Echo Reply messages received. Same as icmpInEchoReps in mib-2.
Status: mandatory Access: read-only
OBJECT-TYPE    
  Counter  

sfrapPerfMgmtIpICMPOutMsgs 1.3.6.1.4.1.485.7.5.2.3.9
The count of all outgoing ICMP messages originating in this node. Same as icmpOutMsgs in mib-2.
Status: mandatory Access: read-only
OBJECT-TYPE    
  Counter  

sfrapPerfMgmtIpICMPOutErrors 1.3.6.1.4.1.485.7.5.2.3.10
The count of outgoing ICMP messages not transmitted due problems found by the ICMP layer. which this entity did Same as icmpOutErrors in mib-2.
Status: mandatory Access: read-only
OBJECT-TYPE    
  Counter  

sfrapPerfMgmtIpICMPOutDestUnreachs 1.3.6.1.4.1.485.7.5.2.3.11
The count of outgoing ICMP Destination Unreachable messages. Same as icmpOutDestUnreachs in mib-2.
Status: mandatory Access: read-only
OBJECT-TYPE    
  Counter  

sfrapPerfMgmtIpICMPOutParmProbs 1.3.6.1.4.1.485.7.5.2.3.12
The count of outgoing ICMP Parameter Problem messages. Same as icmpOutParmProbs in mib-2.
Status: mandatory Access: read-only
OBJECT-TYPE    
  Counter  

sfrapPerfMgmtIpICMPOutRedirects 1.3.6.1.4.1.485.7.5.2.3.13
The count of outgoing ICMP Redirect messages. Same as icmpOutRedirects in mib-2.
Status: mandatory Access: read-only
OBJECT-TYPE    
  Counter  

sfrapPerfMgmtIpICMPOutEchos 1.3.6.1.4.1.485.7.5.2.3.14
The count of outgoing ICMP Echo messages. Same as icmpOutEchos in mib-2.
Status: mandatory Access: read-only
OBJECT-TYPE    
  Counter  

sfrapPerfMgmtIpICMPOutEchoReps 1.3.6.1.4.1.485.7.5.2.3.15
The count of outgoing ICMP Echo Reply messages. Same as icmpOutEchoReps in mib-2.
Status: mandatory Access: read-only
OBJECT-TYPE    
  Counter  

sfrapPerfMgmtIpUDPStatsTable 1.3.6.1.4.1.485.7.5.2.4
OBJECT IDENTIFIER    

sfrapPerfMgmtIpUDPInDatagrams 1.3.6.1.4.1.485.7.5.2.4.1
The count of all UDP datagrams received that are addressed as management frames for this unit. Same as udpInDatagrams in mib-2.
Status: mandatory Access: read-only
OBJECT-TYPE    
  Counter  

sfrapPerfMgmtIpUDPOutDatagrams 1.3.6.1.4.1.485.7.5.2.4.2
The count of all UDP datagrams generated by this unit. Same as udpOutDatagrams in mib-2.
Status: mandatory Access: read-only
OBJECT-TYPE    
  Counter  

sfrapPerfMgmtIpUDPNoPorts 1.3.6.1.4.1.485.7.5.2.4.3
The count of all UDP datagrams received that are addressed as management frames for this unit with no application at the destination port. Same as udpNoPorts in mib-2.
Status: mandatory Access: read-only
OBJECT-TYPE    
  Counter  

sfrapPerfMgmtIpTCPStatsTable 1.3.6.1.4.1.485.7.5.2.5
OBJECT IDENTIFIER    

sfrapPerfMgmtIpTCPActiveOpens 1.3.6.1.4.1.485.7.5.2.5.1
The count of the times TCP connections specific to this unit have made a direct state transition from CLOSED to SYN-SENT. Same as tcpActiveOpens in mib-2.
Status: mandatory Access: read-only
OBJECT-TYPE    
  Counter  

sfrapPerfMgmtIpTCPPassiveOpens 1.3.6.1.4.1.485.7.5.2.5.2
The count of the times TCP connections specific to this unit have made a direct state transition from CLOSED to SYN-RCVD. Same as tcpPassiveOpens in mib-2.
Status: mandatory Access: read-only
OBJECT-TYPE    
  Counter  

sfrapPerfMgmtIpTCPAttemptFails 1.3.6.1.4.1.485.7.5.2.5.3
The count of the times TCP connections specific to this unit have made a direct state transition from SYN-SENT or SYN-RCVD to CLOSED state, plus the count of the times TCP connections have made a direct state transition from SYN-RCVD to LISTEN. Same as tcpAttemptFails in mib-2.
Status: mandatory Access: read-only
OBJECT-TYPE    
  Counter  

sfrapPerfMgmtIpTCPCurrEstab 1.3.6.1.4.1.485.7.5.2.5.4
The count of the TCP connections specific to this unit in state ESTABLISHED or CLOSE-WAIT. Same as tcpCurrEstab in mib-2.
Status: mandatory Access: read-only
OBJECT-TYPE    
  Gauge  

sfrapPerfMgmtIpTCPInSegs 1.3.6.1.4.1.485.7.5.2.5.5
The count of all the segments received that are addressed as management frames for this unit. Same as tcpInSegs in mib-2.
Status: mandatory Access: read-only
OBJECT-TYPE    
  Counter  

sfrapPerfMgmtIpTCPOutSegs 1.3.6.1.4.1.485.7.5.2.5.6
The count of all the segments generated from this unit. Same as tcpOutSegs in mib-2.
Status: mandatory Access: read-only
OBJECT-TYPE    
  Counter  

sfrapPerfThruput 1.3.6.1.4.1.485.7.5.3
OBJECT IDENTIFIER    

sfrapPerfThruputPerIntfTable 1.3.6.1.4.1.485.7.5.3.1
The throughput per interface table. These values are accumulated across all DLCIs.
Status: mandatory Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    SfrapPerfThruputPerIntfEntry

sfrapPerfThruputPerIntfEntry 1.3.6.1.4.1.485.7.5.3.1.1
An entry in the throughput per interface table.
Status: mandatory Access: not-accessible
OBJECT-TYPE    
  SfrapPerfThruputPerIntfEntry  

sfrapPerfThruputPerIntfIndex 1.3.6.1.4.1.485.7.5.3.1.1.1
Interface for which the statistics apply. (1) TO-DTE interface (2) TO-DCE interface
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER to-dte(1), to-dce(2)  

sfrapPerfThruputPerIntfRxByteCnt 1.3.6.1.4.1.485.7.5.3.1.1.2
The number of framed bytes that have been received on this interface.
Status: mandatory Access: read-only
OBJECT-TYPE    
  Counter  

sfrapPerfThruputPerIntfTxByteCnt 1.3.6.1.4.1.485.7.5.3.1.1.3
The number of framed bytes that have been transmitted on this interface.
Status: mandatory Access: read-only
OBJECT-TYPE    
  Counter  

sfrapPerfThruputPerIntfRxFrameCnt 1.3.6.1.4.1.485.7.5.3.1.1.4
The number of frames that have been received on this interface.
Status: mandatory Access: read-only
OBJECT-TYPE    
  Counter  

sfrapPerfThruputPerIntfTxFrameCnt 1.3.6.1.4.1.485.7.5.3.1.1.5
The number of frames that have been transmitted on this interface.
Status: mandatory Access: read-only
OBJECT-TYPE    
  Counter  

sfrapPerfThruputPerIntfRxCrcErrCnt 1.3.6.1.4.1.485.7.5.3.1.1.6
The number of frames with CRC errors received on this interface.
Status: mandatory Access: read-only
OBJECT-TYPE    
  Counter  

sfrapPerfThruputPerIntfRxAbortCnt 1.3.6.1.4.1.485.7.5.3.1.1.7
The number of aborted frames received on this interface.
Status: mandatory Access: read-only
OBJECT-TYPE    
  Counter  

sfrapPerfThruputPerIntfRxBpvCnt 1.3.6.1.4.1.485.7.5.3.1.1.8
The number of BPV errors received on this interface.
Status: mandatory Access: read-only
OBJECT-TYPE    
  Counter  

sfrapPerfThruputPerDlciTable 1.3.6.1.4.1.485.7.5.3.2
Layer 2 statistics on a per-DLCI basis. Transmit direction is from TO-DTE to WAN and receive direction is from the WAN towards the TO-DTE.
Status: mandatory Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    SfrapPerfThruputPerDlciEntry

sfrapPerfThruputPerDlciEntry 1.3.6.1.4.1.485.7.5.3.2.1
The Statistics for a particular Data Link Connection Management Interface (DLCI).
Status: mandatory Access: not-accessible
OBJECT-TYPE    
  SfrapPerfThruputPerDlciEntry  

sfrapPerfThruputPerDlciIndex 1.3.6.1.4.1.485.7.5.3.2.1.1
This value must be in the range 1-3. Other than that, this value is ignored as all three will return the same result.
Status: mandatory Access: read-only
OBJECT-TYPE    
  Index  

sfrapPerfThruputPerDlciValue 1.3.6.1.4.1.485.7.5.3.2.1.2
The DLCI value in which the Statistics are associated.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER  

sfrapPerfThruputPerDlciCreateTime 1.3.6.1.4.1.485.7.5.3.2.1.3
The amount of time elapsed since this DLCI was first detected through traffic sensing or in an LMI message (in seconds).
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER  

sfrapPerfThruputPerDlciChangeTime 1.3.6.1.4.1.485.7.5.3.2.1.4
The amount of elapsed time since this DLCI last changed state from active to inactive or vice versa (in seconds).
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER  

sfrapPerfThruputPerDlciRxByte 1.3.6.1.4.1.485.7.5.3.2.1.5
The number of bytes that have been received from the WAN towards the DTE on this DLCI. This count will include any frames that are terminated by the unit and do not pass through to the opposite interface (management and networking data).
Status: mandatory Access: read-only
OBJECT-TYPE    
  Counter  

sfrapPerfThruputPerDlciTxByte 1.3.6.1.4.1.485.7.5.3.2.1.6
The number of bytes that have been transmitted from the TO-DTE towards the WAN on this DLCI. This count will include any frames that are terminated by the unit and do not pass through to the opposite interface (management and networking data).
Status: mandatory Access: read-only
OBJECT-TYPE    
  Counter  

sfrapPerfThruputPerDlciRxFrame 1.3.6.1.4.1.485.7.5.3.2.1.7
The number of frames that have been received from the WAN towards to the DTE on this DLCI. This count will include any frames that are terminated by the unit and do not pass through to the opposite interface (management and networking data).
Status: mandatory Access: read-only
OBJECT-TYPE    
  Counter  

sfrapPerfThruputPerDlciTxFrame 1.3.6.1.4.1.485.7.5.3.2.1.8
The number of frames that have been transmitted from the TO-DTE towards the WAN on this DLCI. This count will include any frames that are terminated by the unit and do not pass through to the opposite interface (management and networking data).
Status: mandatory Access: read-only
OBJECT-TYPE    
  Counter  

sfrapPerfThruputPerDlciRxFecn 1.3.6.1.4.1.485.7.5.3.2.1.9
The number of frames received from the WAN towards the TO-DTE that have had the Forward Explict Congestion Notification (FECN) bit set on this DLCI. This count will include any frames that are terminated by the unit and do not pass through to the opposite interface (management and networking data).
Status: mandatory Access: read-only
OBJECT-TYPE    
  Counter  

sfrapPerfThruputPerDlciRxBecn 1.3.6.1.4.1.485.7.5.3.2.1.10
The number of frames received from the WAN towards the TO-DTE that have had the Backward Explict Congestion Notification (BECN) bit set on this DLCI. This count will include any frames that are terminated by the unit and do not pass through to the opposite interface (management and networking data).
Status: mandatory Access: read-only
OBJECT-TYPE    
  Counter  

sfrapPerfThruputPerDlciRxDe 1.3.6.1.4.1.485.7.5.3.2.1.11
The number of frames received from the WAN towards the TO-DTE that have had the Discard Eligibility (DE) bit set on this DLCI. This count will include any frames that are terminated by the unit and do not pass through to the opposite interface (management and networking data).
Status: mandatory Access: read-only
OBJECT-TYPE    
  Counter  

sfrapPerfThruputPerDlciTxDe 1.3.6.1.4.1.485.7.5.3.2.1.12
The number of frames transmit towards the WAN from the TO-DTE that have had the Discard Eligibility (DE) bit set on this DLCI. This count will include any frames that are terminated by the unit and do not pass through to the opposite interface (management and networking data).
Status: mandatory Access: read-only
OBJECT-TYPE    
  Counter  

sfrapPerfThruputPerDlciRxThruput 1.3.6.1.4.1.485.7.5.3.2.1.13
The number of bits/sec received from the WAN on this DLCI. This count will include any frames that are terminated by the unit and do not pass through to the opposite interface (management and networking data).
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER  

sfrapPerfThruputPerDlciTxThruput 1.3.6.1.4.1.485.7.5.3.2.1.14
The number of bits/sec transmit to the WAN on this DLCI. This count will include any frames that are terminated by the unit and do not pass through to the opposite interface (management and networking data).
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER  

sfrapPerfThruputPerDlciCIR 1.3.6.1.4.1.485.7.5.3.2.1.15
The Committed Information Rate (CIR) for this DLCI. This can come form one of three sources: From the LMI Full Status Response, configured by the user, or the DTE line rate (default).
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER  

sfrapPerfThruputPerDlciCirType 1.3.6.1.4.1.485.7.5.3.2.1.18
The source of the CIR value for this DLCI. (1) CIR acquired from LMI message. Will override user configured CIR. This feature is not supported by all Frame Relay DCE (switches). (2) CIR configured by user. (3) CIR is DTE Line Rate. Default if CIR is not set by one of the other methods.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER cir-acquired-from-lmi(1), cir-configured-by-user(2), cir-is-dte-datarate(3)  

sfrapPerfThruputPerDlciUptime 1.3.6.1.4.1.485.7.5.3.2.1.16
The total amount of time that the DLCI has been up as reported by the LMI Full Status Response (in seconds).
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER  

sfrapPerfThruputPerDlciDowntime 1.3.6.1.4.1.485.7.5.3.2.1.17
The total amount of time that the DLCI has been declared down (in seconds). A DLCI is Down if it's explicitly declared Inactive through LMI or if it's missing from the LMI Full Status message or if there is no Full Status message at all.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER  

sfrapPerfThruputPerDlciPvcState 1.3.6.1.4.1.485.7.5.3.2.1.19
The current state of the DLCI: (1) DLCI marked active in last full status LMI (2) DLCI in last full status LMI but not marked active (3) DLCI has never been seen in a full status LMI (4) DLCI was seen at least once in a full status LMI but was not in the last full status LMI (5) the full status LMI has timed out; all previously active or inactive DLCIs are changed to this state (6) DLCI was detected in the traffic stream and a full status LMI has not been received so the state cannot be determined yet.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER pvc-active(1), pvc-inactive(2), pvc-unprovisioned(3), pvc-not-in-lmi(4), pvc-lmi-timeout(5), pvc-undetermined(6)  

sfrapPerfThruputPerDlciOutageCount 1.3.6.1.4.1.485.7.5.3.2.1.20
The number of times the smperPerfThruputPerDlciPvcState transitions from pvc-active or pvc-undetermined to one of the other (inactive) states.
Status: mandatory Access: read-only
OBJECT-TYPE    
  Counter  

sfrapPerfThruputPerDlciAvailability 1.3.6.1.4.1.485.7.5.3.2.1.21
The measure of the percentage time the DLCI is available: UpTime/CreateTime or zero if CreateTime = 0. (in 1/1000 per cent; i.e. availability = 1000 converts to 1%).
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER  

sfrapPerfThruputPerDlciMTBSO 1.3.6.1.4.1.485.7.5.3.2.1.22
Mean Time Between Service Outages: UpTime/OutageCount or zero if OutageCount = 0 (in seconds).
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER  

sfrapPerfThruputPerDlciMTTSR 1.3.6.1.4.1.485.7.5.3.2.1.23
Mean Time to ServiceRestoral: DownTime/OutageCount or zero if OutageCount = 0 (in seconds).
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER  

sfrapPerfThruputPerDlciEncapType 1.3.6.1.4.1.485.7.5.3.2.1.24
The encapsulation protocol seen in the last frame analyzed on this DLCI: (1) DLCI is the LMI DLCI or no frames have been analyzed (2) The encapsulation is per rfc1490 (3) The encapsulation is per Cisco proprietary (4) The encapsulation is per Annex-G (X.25 over frame relay) (5) The encapsulation is not one of the above.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER encap-na(1), encap-1490(2), encap-cisco(3), encap-annex-g(4), encap-other(5)  

sfrapPerfThruputPerDlciRxUtilizationStatus 1.3.6.1.4.1.485.7.5.3.2.1.25
The status of the per-DLCI utilization alarm in the receive direction. (1) there is no alarm condition; utilization is under the configured CIR percentage threshold; if traps are enabled and the alarm had been previously triggered, a utilization alarm clear trap will be sent. (2) the utilization has been over the configured CIR percentage threshold for less than the configured duration. (3) the utilization has been over the configured CIR percentage threshold for more than the configured duration; if traps are enabled a utilization exceeded trap will be sent. (4) the utilization has been under the configured CIR percentage threshold for less than the configured duration.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER clear(1), over-threshold(2), alarm(3), alarm-under-threshold(4)  

sfrapPerfThruputPerDlciTxUtilizationStatus 1.3.6.1.4.1.485.7.5.3.2.1.26
The status of the per-DLCI utilization alarm in the transmit direction. (1) there is no alarm condition; utilization is under the configured CIR percentage threshold; if traps are enabled and the alarm had been previously triggered, a utilization alarm clear trap will be sent. (2) the utilization has been over the configured CIR percentage threshold for less than the configured duration. (3) the utilization has been over the configured CIR percentage threshold for more than the configured duration; if traps are enabled a utilization exceeded trap will be sent. (4) the utilization has been under the configured CIR percentage threshold for less than the configured duration.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER clear(1), over-threshold(2), alarm(3), alarm-under-threshold(4)  

sfrapPerfThruputPerDlciEIR 1.3.6.1.4.1.485.7.5.3.2.1.27
The Excess Information Rate. This is defined to be the maximum rate traffic is (supposed to be) allowed to burst to.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER  

sfrapPerfThruputCommands 1.3.6.1.4.1.485.7.5.3.3
OBJECT IDENTIFIER    

sfrapPerfThruputCmdClearToDteStats 1.3.6.1.4.1.485.7.5.3.3.1
Allows the user to zero out all the interface statistics in the TO-DTE portion of the ThruputPerIntf statistics table. (1) Clear TO-DTE interface statistics command.
Status: mandatory Access: write-only
OBJECT-TYPE    
  INTEGER clear-statistics(1)  

sfrapPerfThruputCmdClearToDceStats 1.3.6.1.4.1.485.7.5.3.3.2
Allows the user to zero out all the interface statistics in the WAN portion of the ThruputPerIntf statistics table. (1) Clear WAN interface statistics command.
Status: mandatory Access: write-only
OBJECT-TYPE    
  INTEGER clear-statistics(1)  

sfrapPerfThruputCmdClearAllIntfStats 1.3.6.1.4.1.485.7.5.3.3.3
Allows the user to zero out all the statistics in the ThruputPerIntf statistics table.
Status: mandatory Access: write-only
OBJECT-TYPE    
  INTEGER clear-statistics(1)  

sfrapPerfThruputCmdClearDlciStats 1.3.6.1.4.1.485.7.5.3.3.4
Allows the user to zero out all the per-DLCI statistics in the ThruputPerDlci statistics table and the the short term statistics tables. (1) Clear layer 2 per-DLCI statistics command.
Status: mandatory Access: write-only
OBJECT-TYPE    
  INTEGER clear-statistics(1)  

sfrapPerfThruputCmdClearAllStats 1.3.6.1.4.1.485.7.5.3.3.5
Allows the user to zero out all the statistics in the ThruputPerIntf and ThruputPerDlci statistics tables and in the short term statistics tables. (1) Clear all interface and layer 2 per-DLCI statistics.
Status: mandatory Access: write-only
OBJECT-TYPE    
  INTEGER clear-statistics(1)  

sfrapPerfThruputCmdRemoveStsDlci 1.3.6.1.4.1.485.7.5.3.3.6
Allows the user to remove a Dlci from the short term statistics tables.
Status: mandatory Access: write-only
OBJECT-TYPE    
  INTEGER  

sfrapPerfThruputCmdReplaceDlciTable 1.3.6.1.4.1.485.7.5.3.3.7
Allows the user to replace one DLCI in the short-term statistics table with another one.
Status: mandatory Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    SfrapPerfThruputCmdReplaceDlciEntry

sfrapPerfThruputCmdReplaceDlciEntry 1.3.6.1.4.1.485.7.5.3.3.7.1
Allows the user to replace one DLCI in the short-term statistics table with another one.
Status: mandatory Access: not-accessible
OBJECT-TYPE    
  SfrapPerfThruputCmdReplaceDlciEntry  

sfrapPerfThruputCmdReplaceDlciValue 1.3.6.1.4.1.485.7.5.3.3.7.1.1
A Dlci that is in the short-term stats table. Index by this Dlci value to identify the statistics entry to be replaced.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER  

sfrapPerfThruputCmdReplaceDlciNewValue 1.3.6.1.4.1.485.7.5.3.3.7.1.2
A Dlci that is to replace another in the short-term stats table. Index by this Dlci value to identify the statistics entry to do the replacing.
Status: mandatory Access: write-only
OBJECT-TYPE    
  INTEGER  

sfrapPerfThruputCmdAvailabilityStsDlciReset 1.3.6.1.4.1.485.7.5.3.3.8
Allows the user to reset the availability statistics of an individual Dlci within the short-term stats table.
Status: mandatory Access: write-only
OBJECT-TYPE    
  INTEGER  

sfrapPerfThruputCmdAvailabilityStsDlciResetAll 1.3.6.1.4.1.485.7.5.3.3.9
Allows the user to reset the availability statistics of all Dlci's within the short-term stats table.
Status: mandatory Access: write-only
OBJECT-TYPE    
  INTEGER  

sfrapPerfThruputCmdCountsStsDlciReset 1.3.6.1.4.1.485.7.5.3.3.10
Allows the user to reset the count statistics of an individual Dlci within the short-term stats table.
Status: mandatory Access: write-only
OBJECT-TYPE    
  INTEGER  

sfrapPerfThruputCmdCountsStsDlciResetAll 1.3.6.1.4.1.485.7.5.3.3.11
Allows the user to reset the count statistics of all Dlci's within the short-term stats table.
Status: mandatory Access: write-only
OBJECT-TYPE    
  INTEGER  

sfrapPerfThruputCmdAllStsDlciReset 1.3.6.1.4.1.485.7.5.3.3.12
Allows the user to reset both the count and availability statistics of an individual Dlci within the short-term stats table.
Status: mandatory Access: write-only
OBJECT-TYPE    
  INTEGER  

sfrapPerfThruputCmdAllStsDlciResetAll 1.3.6.1.4.1.485.7.5.3.3.13
Allows the user to reset both the count and the availability statistics of all Dlci's within the short-term stats table.
Status: mandatory Access: write-only
OBJECT-TYPE    
  INTEGER  

sfrapPerfNetworkShortTerm 1.3.6.1.4.1.485.7.5.4
OBJECT IDENTIFIER    

sfrapPerfNetwProtoPerDlciTable 1.3.6.1.4.1.485.7.5.4.1
The Short Term Statistics on the Network Layer protocol for each DLCI. These are protocol-based per-DLCI statistics. The Short Term model maintains three intervals: current, previous, and cumulative totals. Interval duration is defined by the Short Term Timer (CfgFrPerfTimersSTInterval).
Status: mandatory Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    SfrapPerfNetwProtoPerDlciEntry

sfrapPerfNetwProtoPerDlciEntry 1.3.6.1.4.1.485.7.5.4.1.1
The Network Layer Short Term Statistics for a particular DLCI. This table organizes statistics by high-layer network protocol.
Status: mandatory Access: not-accessible
OBJECT-TYPE    
  SfrapPerfNetwProtoPerDlciEntry  

sfrapPerfNetwProtoPerDlciInterval 1.3.6.1.4.1.485.7.5.4.1.1.1
The Short Term statistics model maintains three intervals: current, previous, and cumulative totals. Interval duration is defined by the Short Term Timer (CfgFrPerfTimersSTInterval). (1) Currently active short term interval (2) Previously completed short term interval (3) Cumulative total since last cleared.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER current-interval(1), previous-interval(2), cumulative-counts(3)  

sfrapPerfNetwProtoPerDlciValue 1.3.6.1.4.1.485.7.5.4.1.1.2
The DLCI value with which the Statistics are associated.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER  

sfrapPerfNetwProtoPerDlciRxTotal 1.3.6.1.4.1.485.7.5.4.1.1.3
The total number of received Network Layer bytes that have been counted on this DLCI.
Status: mandatory Access: read-only
OBJECT-TYPE    
  Counter  

sfrapPerfNetwProtoPerDlciTxTotal 1.3.6.1.4.1.485.7.5.4.1.1.4
The total number of transmitted Network Layer bytes that have been counted on this DLCI.
Status: mandatory Access: read-only
OBJECT-TYPE    
  Counter  

sfrapPerfNetwProtoPerDlciRxIp 1.3.6.1.4.1.485.7.5.4.1.1.5
The number of received IP bytes that have been counted on this DLCI.
Status: mandatory Access: read-only
OBJECT-TYPE    
  Counter  

sfrapPerfNetwProtoPerDlciTxIp 1.3.6.1.4.1.485.7.5.4.1.1.6
The number of transmitted IP bytes that have been counted on this DLCI.
Status: mandatory Access: read-only
OBJECT-TYPE    
  Counter  

sfrapPerfNetwProtoPerDlciRxIpx 1.3.6.1.4.1.485.7.5.4.1.1.7
The number of received IPX bytes that have been counted on this DLCI.
Status: mandatory Access: read-only
OBJECT-TYPE    
  Counter  

sfrapPerfNetwProtoPerDlciTxIpx 1.3.6.1.4.1.485.7.5.4.1.1.8
The number of transmitted IPX bytes that have been counted on this DLCI.
Status: mandatory Access: read-only
OBJECT-TYPE    
  Counter  

sfrapPerfNetwProtoPerDlciRxSna 1.3.6.1.4.1.485.7.5.4.1.1.9
The number of received SNA bytes that have been counted on this DLCI.
Status: mandatory Access: read-only
OBJECT-TYPE    
  Counter  

sfrapPerfNetwProtoPerDlciTxSna 1.3.6.1.4.1.485.7.5.4.1.1.10
The number of transmitted SNA bytes that have been counted on this DLCI.
Status: mandatory Access: read-only
OBJECT-TYPE    
  Counter  

sfrapPerfNetwProtoPerDlciRxArp 1.3.6.1.4.1.485.7.5.4.1.1.11
The number of received ARP bytes that have been counted on this DLCI.
Status: mandatory Access: read-only
OBJECT-TYPE    
  Counter  

sfrapPerfNetwProtoPerDlciTxArp 1.3.6.1.4.1.485.7.5.4.1.1.12
The number of transmitted ARP bytes that have been counted on this DLCI.
Status: mandatory Access: read-only
OBJECT-TYPE    
  Counter  

sfrapPerfNetwProtoPerDlciRxCisco 1.3.6.1.4.1.485.7.5.4.1.1.13
The number of received Cisco protocol bytes that have been counted on this DLCI.
Status: mandatory Access: read-only
OBJECT-TYPE    
  Counter  

sfrapPerfNetwProtoPerDlciTxCisco 1.3.6.1.4.1.485.7.5.4.1.1.14
The number of transmitted Cisco protocol bytes that have been counted on this DLCI.
Status: mandatory Access: read-only
OBJECT-TYPE    
  Counter  

sfrapPerfNetwProtoPerDlciRxOther 1.3.6.1.4.1.485.7.5.4.1.1.15
The number of received bytes on this DLCI from protocols that are not counted elsewhere in this table.
Status: mandatory Access: read-only
OBJECT-TYPE    
  Counter  

sfrapPerfNetwProtoPerDlciTxOther 1.3.6.1.4.1.485.7.5.4.1.1.16
The number of transmitted bytes on this DLCI from protocols that are not counted elsewhere in this table.
Status: mandatory Access: read-only
OBJECT-TYPE    
  Counter  

sfrapPerfNetwProtoPerDlciRxVnip 1.3.6.1.4.1.485.7.5.4.1.1.17
The number of received VNIP protocol bytes that have been counted on this DLCI.
Status: mandatory Access: read-only
OBJECT-TYPE    
  Counter  

sfrapPerfNetwProtoPerDlciTxVnip 1.3.6.1.4.1.485.7.5.4.1.1.18
The number of transmitted VNIP protocol bytes that have been counted on this DLCI.
Status: mandatory Access: read-only
OBJECT-TYPE    
  Counter  

sfrapPerfNetwProtoPerDlciRxAnnexG 1.3.6.1.4.1.485.7.5.4.1.1.19
The number of received Annex G protocol bytes that have been counted on this DLCI.
Status: mandatory Access: read-only
OBJECT-TYPE    
  Counter  

sfrapPerfNetwProtoPerDlciTxAnnexG 1.3.6.1.4.1.485.7.5.4.1.1.20
The number of transmitted Annex G protocol bytes that have been counted on this DLCI.
Status: mandatory Access: read-only
OBJECT-TYPE    
  Counter  

sfrapPerfNetwProtoTotalTable 1.3.6.1.4.1.485.7.5.4.2
The Short Term Statistics on Network Layer protocols summed across all DLCIs.
Status: mandatory Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    SfrapPerfNetwProtoTotalEntry

sfrapPerfNetwProtoTotalEntry 1.3.6.1.4.1.485.7.5.4.2.1
The Network Layer Short Term Statistics for a particular DLCI.
Status: mandatory Access: not-accessible
OBJECT-TYPE    
  SfrapPerfNetwProtoTotalEntry  

sfrapPerfNetwProtoTotalInterval 1.3.6.1.4.1.485.7.5.4.2.1.1
The Short Term statistics model maintains three intervals: current, previous, and cumulative totals. Interval duration is defined by the Short Term Timer (CfgFrPerfTimersSTInterval). (1) Currently active short term interval (2) Previously completed short term interval (3) Cumulative total since last cleared.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER current-interval(1), previous-interval(2), cumulative-counts(3)  

sfrapPerfNetwProtoTotalRxTotal 1.3.6.1.4.1.485.7.5.4.2.1.3
The total number of received Network Layer bytes that have been counted across all DLCIs.
Status: mandatory Access: read-only
OBJECT-TYPE    
  Counter  

sfrapPerfNetwProtoTotalTxTotal 1.3.6.1.4.1.485.7.5.4.2.1.4
The total number of transmitted Network Layer bytes that have been counted across all DLCIs.
Status: mandatory Access: read-only
OBJECT-TYPE    
  Counter  

sfrapPerfNetwProtoTotalRxIp 1.3.6.1.4.1.485.7.5.4.2.1.5
The number of received IP bytes that have been counted across all DLCIs.
Status: mandatory Access: read-only
OBJECT-TYPE    
  Counter  

sfrapPerfNetwProtoTotalTxIp 1.3.6.1.4.1.485.7.5.4.2.1.6
The number of transmitted IP bytes that have been counted across all DLCIs.
Status: mandatory Access: read-only
OBJECT-TYPE    
  Counter  

sfrapPerfNetwProtoTotalRxIpx 1.3.6.1.4.1.485.7.5.4.2.1.7
The number of received IPX bytes that have been counted across all DLCIs.
Status: mandatory Access: read-only
OBJECT-TYPE    
  Counter  

sfrapPerfNetwProtoTotalTxIpx 1.3.6.1.4.1.485.7.5.4.2.1.8
The number of transmitted IPX bytes that have been counted across all DLCIs.
Status: mandatory Access: read-only
OBJECT-TYPE    
  Counter  

sfrapPerfNetwProtoTotalRxSna 1.3.6.1.4.1.485.7.5.4.2.1.9
The number of received SNA bytes that have been counted across all DLCIs.
Status: mandatory Access: read-only
OBJECT-TYPE    
  Counter  

sfrapPerfNetwProtoTotalTxSna 1.3.6.1.4.1.485.7.5.4.2.1.10
The number of transmitted SNA bytes that have been counted across all DLCIs.
Status: mandatory Access: read-only
OBJECT-TYPE    
  Counter  

sfrapPerfNetwProtoTotalRxArp 1.3.6.1.4.1.485.7.5.4.2.1.11
The number of received ARP bytes that have been counted across all DLCIs.
Status: mandatory Access: read-only
OBJECT-TYPE    
  Counter  

sfrapPerfNetwProtoTotalTxArp 1.3.6.1.4.1.485.7.5.4.2.1.12
The number of transmitted ARP bytes that have been counted across all DLCIs.
Status: mandatory Access: read-only
OBJECT-TYPE    
  Counter  

sfrapPerfNetwProtoTotalRxCisco 1.3.6.1.4.1.485.7.5.4.2.1.13
The number of received Cisco protocol bytes that have been counted across all DLCIs.
Status: mandatory Access: read-only
OBJECT-TYPE    
  Counter  

sfrapPerfNetwProtoTotalTxCisco 1.3.6.1.4.1.485.7.5.4.2.1.14
The number of transmitted Cisco protocol bytes that have been counted across all DLCIs.
Status: mandatory Access: read-only
OBJECT-TYPE    
  Counter  

sfrapPerfNetwProtoTotalRxOther 1.3.6.1.4.1.485.7.5.4.2.1.15
The number of received bytes across all DLCIs from protocols that are not counted elsewhere in this table.
Status: mandatory Access: read-only
OBJECT-TYPE    
  Counter  

sfrapPerfNetwProtoTotalTxOther 1.3.6.1.4.1.485.7.5.4.2.1.16
The number of transmitted bytes across all DLCIs from protocols that are not counted elsewhere in this table.
Status: mandatory Access: read-only
OBJECT-TYPE    
  Counter  

sfrapPerfNetwProtoTotalRxVnip 1.3.6.1.4.1.485.7.5.4.2.1.17
The number of received VNIP protocol bytes that have been counted across all DLCIs.
Status: mandatory Access: read-only
OBJECT-TYPE    
  Counter  

sfrapPerfNetwProtoTotalTxVnip 1.3.6.1.4.1.485.7.5.4.2.1.18
The number of transmitted VNIP protocol bytes that have been counted across all DLCIs.
Status: mandatory Access: read-only
OBJECT-TYPE    
  Counter  

sfrapPerfNetwProtoTotalRxAnnexG 1.3.6.1.4.1.485.7.5.4.2.1.19
The number of received Annex G protocol bytes that have been counted across all DLCIs.
Status: mandatory Access: read-only
OBJECT-TYPE    
  Counter  

sfrapPerfNetwProtoTotalTxAnnexG 1.3.6.1.4.1.485.7.5.4.2.1.20
The number of transmitted Annex G protocol bytes that have been counted across all DLCIs.
Status: mandatory Access: read-only
OBJECT-TYPE    
  Counter  

sfrapPerfIpPerDlciTable 1.3.6.1.4.1.485.7.5.4.3
The Short Term Statistics on the IP protocol for each DLCI.
Status: mandatory Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    SfrapPerfIpPerDlciEntry

sfrapPerfIpPerDlciEntry 1.3.6.1.4.1.485.7.5.4.3.1
The IP Short Term Statistics for a particular DLCI.
Status: mandatory Access: not-accessible
OBJECT-TYPE    
  SfrapPerfIpPerDlciEntry  

sfrapPerfIpPerDlciInterval 1.3.6.1.4.1.485.7.5.4.3.1.1
The Short Term statistics model maintains three intervals: current, previous, and cumulative totals. Interval duration is defined by the Short Term Timer (CfgFrPerfTimersSTInterval). (1) Currently active short term interval (2) Previously completed short term interval (3) Cumulative total since last cleared.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER current-interval(1), previous-interval(2), cumulative-counts(3)  

sfrapPerfIpPerDlciValue 1.3.6.1.4.1.485.7.5.4.3.1.2
The DLCI value with which the Statistics are associated.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER  

sfrapPerfIpPerDlciRxTotal 1.3.6.1.4.1.485.7.5.4.3.1.3
The total number of received IP bytes that have been counted on this DLCI.
Status: mandatory Access: read-only
OBJECT-TYPE    
  Counter  

sfrapPerfIpPerDlciTxTotal 1.3.6.1.4.1.485.7.5.4.3.1.4
The total number of transmitted IP bytes that have been counted on this DLCI.
Status: mandatory Access: read-only
OBJECT-TYPE    
  Counter  

sfrapPerfIpPerDlciRxTcp 1.3.6.1.4.1.485.7.5.4.3.1.5
The number of received TCP over IP bytes that have been counted on this DLCI.
Status: mandatory Access: read-only
OBJECT-TYPE    
  Counter  

sfrapPerfIpPerDlciTxTcp 1.3.6.1.4.1.485.7.5.4.3.1.6
The number of transmitted TCP over IP bytes that have been counted on this DLCI.
Status: mandatory Access: read-only
OBJECT-TYPE    
  Counter  

sfrapPerfIpPerDlciRxUdp 1.3.6.1.4.1.485.7.5.4.3.1.7
The number of received UDP over IP bytes that have been counted on this DLCI.
Status: mandatory Access: read-only
OBJECT-TYPE    
  Counter  

sfrapPerfIpPerDlciTxUdp 1.3.6.1.4.1.485.7.5.4.3.1.8
The number of transmitted UDP over IP bytes that have been counted on this DLCI.
Status: mandatory Access: read-only
OBJECT-TYPE    
  Counter  

sfrapPerfIpPerDlciRxIcmp 1.3.6.1.4.1.485.7.5.4.3.1.9
The number of received ICMP over IP bytes that have been counted on this DLCI.
Status: mandatory Access: read-only
OBJECT-TYPE    
  Counter  

sfrapPerfIpPerDlciTxIcmp 1.3.6.1.4.1.485.7.5.4.3.1.10
The number of transmitted ICMP over IP bytes that have been counted on this DLCI.
Status: mandatory Access: read-only
OBJECT-TYPE    
  Counter  

sfrapPerfIpPerDlciRxOther 1.3.6.1.4.1.485.7.5.4.3.1.11
The number of received bytes on this DLCI from protocols over IP that are not counted elsewhere in this table.
Status: mandatory Access: read-only
OBJECT-TYPE    
  Counter  

sfrapPerfIpPerDlciTxOther 1.3.6.1.4.1.485.7.5.4.3.1.12
The number of transmitted bytes on this DLCI from protocols over IP that are not counted elsewhere in this table.
Status: mandatory Access: read-only
OBJECT-TYPE    
  Counter  

sfrapPerfIpPerDlciRxIgrp 1.3.6.1.4.1.485.7.5.4.3.1.13
The number of received IGRP over IP bytes that have been counted on this DLCI.
Status: mandatory Access: read-only
OBJECT-TYPE    
  Counter  

sfrapPerfIpPerDlciTxIgrp 1.3.6.1.4.1.485.7.5.4.3.1.14
The number of transmitted IGRP over IP bytes that have been counted on this DLCI.
Status: mandatory Access: read-only
OBJECT-TYPE    
  Counter  

sfrapPerfIpTotalTable 1.3.6.1.4.1.485.7.5.4.4
The Short Term Statistics on the IP protocol across all DLCIs.
Status: mandatory Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    SfrapPerfIpTotalEntry

sfrapPerfIpTotalEntry 1.3.6.1.4.1.485.7.5.4.4.1
The IP Short Term Statistics across all DLCIs.
Status: mandatory Access: not-accessible
OBJECT-TYPE    
  SfrapPerfIpTotalEntry  

sfrapPerfIpTotalInterval 1.3.6.1.4.1.485.7.5.4.4.1.1
The Short Term statistics model maintains three intervals: current, previous, and cumulative totals. Interval duration is defined by the Short Term Timer (CfgFrPerfTimersSTInterval). (1) Currently active short term interval (2) Previously completed short term interval (3) Cumulative total since last cleared.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER current-interval(1), previous-interval(2), cumulative-counts(3)  

sfrapPerfIpTotalRxTotal 1.3.6.1.4.1.485.7.5.4.4.1.3
The total number of received IP bytes that have been counted across all DLCIs.
Status: mandatory Access: read-only
OBJECT-TYPE    
  Counter  

sfrapPerfIpTotalTxTotal 1.3.6.1.4.1.485.7.5.4.4.1.4
The total number of transmitted IP bytes that have been counted across all DLCIs.
Status: mandatory Access: read-only
OBJECT-TYPE    
  Counter  

sfrapPerfIpTotalRxTcp 1.3.6.1.4.1.485.7.5.4.4.1.5
The number of received TCP over IP bytes that have been counted across all DLCIs.
Status: mandatory Access: read-only
OBJECT-TYPE    
  Counter  

sfrapPerfIpTotalTxTcp 1.3.6.1.4.1.485.7.5.4.4.1.6
The number of transmitted TCP over IP bytes that have been counted across all DLCIs.
Status: mandatory Access: read-only
OBJECT-TYPE    
  Counter  

sfrapPerfIpTotalRxUdp 1.3.6.1.4.1.485.7.5.4.4.1.7
The number of received UDP over IP bytes that have been counted across all DLCIs.
Status: mandatory Access: read-only
OBJECT-TYPE    
  Counter  

sfrapPerfIpTotalTxUdp 1.3.6.1.4.1.485.7.5.4.4.1.8
The number of transmitted UDP over IP bytes that have been counted across all DLCIs.
Status: mandatory Access: read-only
OBJECT-TYPE    
  Counter  

sfrapPerfIpTotalRxIcmp 1.3.6.1.4.1.485.7.5.4.4.1.9
The number of received ICMP over IP bytes that have been counted across all DLCIs.
Status: mandatory Access: read-only
OBJECT-TYPE    
  Counter  

sfrapPerfIpTotalTxIcmp 1.3.6.1.4.1.485.7.5.4.4.1.10
The number of transmitted ICMP over IP bytes that have been counted across all DLCIs.
Status: mandatory Access: read-only
OBJECT-TYPE    
  Counter  

sfrapPerfIpTotalRxOther 1.3.6.1.4.1.485.7.5.4.4.1.11
The number of received bytes across all DLCIs from protocols over IP that are not counted elsewhere in this table.
Status: mandatory Access: read-only
OBJECT-TYPE    
  Counter  

sfrapPerfIpTotalTxOther 1.3.6.1.4.1.485.7.5.4.4.1.12
The number of transmitted bytes across all DLCIs. from protocols over IP that are not counted elsewhere in this table.
Status: mandatory Access: read-only
OBJECT-TYPE    
  Counter  

sfrapPerfIpTotalRxIgrp 1.3.6.1.4.1.485.7.5.4.4.1.13
The number of received IGRP over IP bytes that have been counted across all DLCIs.
Status: mandatory Access: read-only
OBJECT-TYPE    
  Counter  

sfrapPerfIpTotalTxIgrp 1.3.6.1.4.1.485.7.5.4.4.1.14
The number of transmitted IGRP over IP bytes that have been counted across all DLCIs.
Status: mandatory Access: read-only
OBJECT-TYPE    
  Counter  

sfrapPerfIcmpPerDlciTable 1.3.6.1.4.1.485.7.5.4.5
Short Term Statistics on the ICMP protocol for each DLCI.
Status: mandatory Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    SfrapPerfIcmpPerDlciEntry

sfrapPerfIcmpPerDlciEntry 1.3.6.1.4.1.485.7.5.4.5.1
The ICMP Short Term Statistics for a particular DLCI.
Status: mandatory Access: not-accessible
OBJECT-TYPE    
  SfrapPerfIcmpPerDlciEntry  

sfrapPerfIcmpPerDlciInterval 1.3.6.1.4.1.485.7.5.4.5.1.1
The Short Term statistics model maintains three intervals: current, previous, and cumulative totals. Interval duration is defined by the Short Term Timer (CfgFrPerfTimersSTInterval). (1) Currently active short term interval (2) Previously completed short term interval (3) Cumulative total since last cleared.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER current-interval(1), previous-interval(2), cumulative-counts(3)  

sfrapPerfIcmpPerDlciValue 1.3.6.1.4.1.485.7.5.4.5.1.2
The DLCI value in which the Statistics are associated.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER  

sfrapPerfIcmpPerDlciRxTotal 1.3.6.1.4.1.485.7.5.4.5.1.3
The total number of ICMP bytes that have been counted on this DLCI.
Status: mandatory Access: read-only
OBJECT-TYPE    
  Counter  

sfrapPerfIcmpPerDlciTxTotal 1.3.6.1.4.1.485.7.5.4.5.1.4
The total number of ICMP bytes that have been counted on this DLCI.
Status: mandatory Access: read-only
OBJECT-TYPE    
  Counter  

sfrapPerfIcmpPerDlciRxEchoRep 1.3.6.1.4.1.485.7.5.4.5.1.5
The number of bytes in ICMP ECHO replies that have been counted on this DLCI.
Status: mandatory Access: read-only
OBJECT-TYPE    
  Counter  

sfrapPerfIcmpPerDlciTxEchoRep 1.3.6.1.4.1.485.7.5.4.5.1.6
The number of bytes in ICMP ECHO replies that have been counted on this DLCI.
Status: mandatory Access: read-only
OBJECT-TYPE    
  Counter  

sfrapPerfIcmpPerDlciRxDestUnr 1.3.6.1.4.1.485.7.5.4.5.1.7
The number of bytes in ICMP destination unreachables that have been counted on this DLCI.
Status: mandatory Access: read-only
OBJECT-TYPE    
  Counter  

sfrapPerfIcmpPerDlciTxDestUnr 1.3.6.1.4.1.485.7.5.4.5.1.8
The number of bytes in ICMP destination unreachables that have been counted on this DLCI.
Status: mandatory Access: read-only
OBJECT-TYPE    
  Counter  

sfrapPerfIcmpPerDlciRxSrcQuench 1.3.6.1.4.1.485.7.5.4.5.1.9
The number of bytes in ICMP source quenches that have been counted on this DLCI.
Status: mandatory Access: read-only
OBJECT-TYPE    
  Counter  

sfrapPerfIcmpPerDlciTxSrcQuench 1.3.6.1.4.1.485.7.5.4.5.1.10
The number of bytes in ICMP source quenches that have been counted on this DLCI.
Status: mandatory Access: read-only
OBJECT-TYPE    
  Counter  

sfrapPerfIcmpPerDlciRxRedirect 1.3.6.1.4.1.485.7.5.4.5.1.11
The number of bytes in ICMP redirects that have been counted on this DLCI.
Status: mandatory Access: read-only
OBJECT-TYPE    
  Counter  

sfrapPerfIcmpPerDlciTxRedirect 1.3.6.1.4.1.485.7.5.4.5.1.12
The number of bytes in ICMP redirects that have been counted on this DLCI.
Status: mandatory Access: read-only
OBJECT-TYPE    
  Counter  

sfrapPerfIcmpPerDlciRxEchoReq 1.3.6.1.4.1.485.7.5.4.5.1.13
The number of bytes in ICMP ECHO requests that have been counted on this DLCI.
Status: mandatory Access: read-only
OBJECT-TYPE    
  Counter  

sfrapPerfIcmpPerDlciTxEchoReq 1.3.6.1.4.1.485.7.5.4.5.1.14
The number of bytes in ICMP ECHO requests that have been counted on this DLCI.
Status: mandatory Access: read-only
OBJECT-TYPE    
  Counter  

sfrapPerfIcmpPerDlciRxTimeExcd 1.3.6.1.4.1.485.7.5.4.5.1.15
The number of bytes in ICMP time exceededs that have been counted on this DLCI.
Status: mandatory Access: read-only
OBJECT-TYPE    
  Counter  

sfrapPerfIcmpPerDlciTxTimeExcd 1.3.6.1.4.1.485.7.5.4.5.1.16
The number of bytes in ICMP time exceededs that have been counted on this DLCI.
Status: mandatory Access: read-only
OBJECT-TYPE    
  Counter  

sfrapPerfIcmpPerDlciRxParamProb 1.3.6.1.4.1.485.7.5.4.5.1.17
The number of bytes in ICMP parameter problems that have been counted on this DLCI.
Status: mandatory Access: read-only
OBJECT-TYPE    
  Counter  

sfrapPerfIcmpPerDlciTxParamProb 1.3.6.1.4.1.485.7.5.4.5.1.18
The number of bytes in ICMP parameter problems that have been counted on this DLCI.
Status: mandatory Access: read-only
OBJECT-TYPE    
  Counter  

sfrapPerfIcmpPerDlciRxTimestpReq 1.3.6.1.4.1.485.7.5.4.5.1.19
The number of bytes in ICMP timestamp requests that have been counted on this DLCI.
Status: mandatory Access: read-only
OBJECT-TYPE    
  Counter  

sfrapPerfIcmpPerDlciTxTimestpReq 1.3.6.1.4.1.485.7.5.4.5.1.20
The number of bytes in ICMP timestamp requests that have been counted on this DLCI.
Status: mandatory Access: read-only
OBJECT-TYPE    
  Counter  

sfrapPerfIcmpPerDlciRxTimestpRep 1.3.6.1.4.1.485.7.5.4.5.1.21
The number of bytes in ICMP timestamp replies that have been counted on this DLCI.
Status: mandatory Access: read-only
OBJECT-TYPE    
  Counter  

sfrapPerfIcmpPerDlciTxTimestpRep 1.3.6.1.4.1.485.7.5.4.5.1.22
The number of bytes in ICMP timestamp replies that have been counted on this DLCI.
Status: mandatory Access: read-only
OBJECT-TYPE    
  Counter  

sfrapPerfIcmpPerDlciRxAddrMaskReq 1.3.6.1.4.1.485.7.5.4.5.1.23
The number of bytes in ICMP address mask requests that have been counted on this DLCI.
Status: mandatory Access: read-only
OBJECT-TYPE    
  Counter  

sfrapPerfIcmpPerDlciTxAddrMaskReq 1.3.6.1.4.1.485.7.5.4.5.1.24
The number of bytes in ICMP address mask requests that have been counted on this DLCI.
Status: mandatory Access: read-only
OBJECT-TYPE    
  Counter  

sfrapPerfIcmpPerDlciRxAddrMaskRep 1.3.6.1.4.1.485.7.5.4.5.1.25
The number of bytes in ICMP address mask replies that have been counted on this DLCI.
Status: mandatory Access: read-only
OBJECT-TYPE    
  Counter  

sfrapPerfIcmpPerDlciTxAddrMaskRep 1.3.6.1.4.1.485.7.5.4.5.1.26
The number of bytes in ICMP address mask replies that have been counted on this DLCI.
Status: mandatory Access: read-only
OBJECT-TYPE    
  Counter  

sfrapPerfIcmpPerDlciRxPktTooBig 1.3.6.1.4.1.485.7.5.4.5.1.27
The number of bytes in ICMP packet too bigs that have been counted on this DLCI.
Status: mandatory Access: read-only
OBJECT-TYPE    
  Counter  

sfrapPerfIcmpPerDlciTxPktTooBig 1.3.6.1.4.1.485.7.5.4.5.1.28
The number of bytes in ICMP packet too bigs that have been counted on this DLCI.
Status: mandatory Access: read-only
OBJECT-TYPE    
  Counter  

sfrapPerfIcmpPerDlciRxGmQuery 1.3.6.1.4.1.485.7.5.4.5.1.29
The number of bytes in ICMP group membership queries that have been counted on this DLCI.
Status: mandatory Access: read-only
OBJECT-TYPE    
  Counter  

sfrapPerfIcmpPerDlciTxGmQuery 1.3.6.1.4.1.485.7.5.4.5.1.30
The number of bytes in ICMP group membership queries that have been counted on this DLCI.
Status: mandatory Access: read-only
OBJECT-TYPE    
  Counter  

sfrapPerfIcmpPerDlciRxGmReport 1.3.6.1.4.1.485.7.5.4.5.1.31
The number of bytes in ICMP group membership reports that have been counted on this DLCI.
Status: mandatory Access: read-only
OBJECT-TYPE    
  Counter  

sfrapPerfIcmpPerDlciTxGmReport 1.3.6.1.4.1.485.7.5.4.5.1.32
The number of bytes in ICMP group membership reports that have been counted on this DLCI.
Status: mandatory Access: read-only
OBJECT-TYPE    
  Counter  

sfrapPerfIcmpPerDlciRxGmReduct 1.3.6.1.4.1.485.7.5.4.5.1.33
The number of bytes in ICMP group membership reductions that have been counted on this DLCI.
Status: mandatory Access: read-only
OBJECT-TYPE    
  Counter  

sfrapPerfIcmpPerDlciTxGmReduct 1.3.6.1.4.1.485.7.5.4.5.1.34
The number of bytes in ICMP group membership reductions that have been counted on this DLCI.
Status: mandatory Access: read-only
OBJECT-TYPE    
  Counter  

sfrapPerfIcmpTotalTable 1.3.6.1.4.1.485.7.5.4.6
Short Term Statistics on the ICMP protocol across all DLCIs.
Status: mandatory Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    SfrapPerfIcmpTotalEntry

sfrapPerfIcmpTotalEntry 1.3.6.1.4.1.485.7.5.4.6.1
The ICMP Short Term Statistics for a particular DLCI.
Status: mandatory Access: not-accessible
OBJECT-TYPE    
  SfrapPerfIcmpTotalEntry  

sfrapPerfIcmpTotalInterval 1.3.6.1.4.1.485.7.5.4.6.1.1
The Short Term statistics model maintains three intervals: current, previous, and cumulative totals. Interval duration is defined by the Short Term Timer (CfgFrPerfTimersSTInterval). (1) Currently active short term interval (2) Previously completed short term interval (3) Cumulative total since last cleared.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER current-interval(1), previous-interval(2), cumulative-counts(3)  

sfrapPerfIcmpTotalRxTotal 1.3.6.1.4.1.485.7.5.4.6.1.3
The total number of ICMP bytes that have been counted across all DLCIs.
Status: mandatory Access: read-only
OBJECT-TYPE    
  Counter  

sfrapPerfIcmpTotalTxTotal 1.3.6.1.4.1.485.7.5.4.6.1.4
The total number of ICMP bytes that have been counted across all DLCIs.
Status: mandatory Access: read-only
OBJECT-TYPE    
  Counter  

sfrapPerfIcmpTotalRxEchoRep 1.3.6.1.4.1.485.7.5.4.6.1.5
The number of bytes in ICMP ECHO repies that have been counted across all DLCIs.
Status: mandatory Access: read-only
OBJECT-TYPE    
  Counter  

sfrapPerfIcmpTotalTxEchoRep 1.3.6.1.4.1.485.7.5.4.6.1.6
The number of bytes in ICMP ECHO repies that have been counted across all DLCIs.
Status: mandatory Access: read-only
OBJECT-TYPE    
  Counter  

sfrapPerfIcmpTotalRxDestUnr 1.3.6.1.4.1.485.7.5.4.6.1.7
The number of bytes in ICMP destination unreachables that have been counted across all DLCIs.
Status: mandatory Access: read-only
OBJECT-TYPE    
  Counter  

sfrapPerfIcmpTotalTxDestUnr 1.3.6.1.4.1.485.7.5.4.6.1.8
The number of bytes in ICMP destination unreachables that have been counted across all DLCIs.
Status: mandatory Access: read-only
OBJECT-TYPE    
  Counter  

sfrapPerfIcmpTotalRxSrcQuench 1.3.6.1.4.1.485.7.5.4.6.1.9
The number of bytes in ICMP source quenches that have been counted across all DLCIs.
Status: mandatory Access: read-only
OBJECT-TYPE    
  Counter  

sfrapPerfIcmpTotalTxSrcQuench 1.3.6.1.4.1.485.7.5.4.6.1.10
The number of bytes in ICMP source quenches that have been counte across all DLCIs.
Status: mandatory Access: read-only
OBJECT-TYPE    
  Counter  

sfrapPerfIcmpTotalRxRedirect 1.3.6.1.4.1.485.7.5.4.6.1.11
The number of bytes in ICMP redirects that have been counte across all DLCIs.
Status: mandatory Access: read-only
OBJECT-TYPE    
  Counter  

sfrapPerfIcmpTotalTxRedirect 1.3.6.1.4.1.485.7.5.4.6.1.12
The number of bytes in ICMP redirects that have been counte across all DLCIs.
Status: mandatory Access: read-only
OBJECT-TYPE    
  Counter  

sfrapPerfIcmpTotalRxEchoReq 1.3.6.1.4.1.485.7.5.4.6.1.13
The number of bytes in ICMP ECHO requests that have been counted across all DLCIs.
Status: mandatory Access: read-only
OBJECT-TYPE    
  Counter  

sfrapPerfIcmpTotalTxEchoReq 1.3.6.1.4.1.485.7.5.4.6.1.14
The number of bytes in ICMP ECHO requests that have been counte across all DLCIs.
Status: mandatory Access: read-only
OBJECT-TYPE    
  Counter  

sfrapPerfIcmpTotalRxTimeExcd 1.3.6.1.4.1.485.7.5.4.6.1.15
The number of bytes in ICMP time exceededs that have been counted across all DLCIs.
Status: mandatory Access: read-only
OBJECT-TYPE    
  Counter  

sfrapPerfIcmpTotalTxTimeExcd 1.3.6.1.4.1.485.7.5.4.6.1.16
The number of bytes in ICMP time exceededs that have been counted across all DLCIs.
Status: mandatory Access: read-only
OBJECT-TYPE    
  Counter  

sfrapPerfIcmpTotalRxParamProb 1.3.6.1.4.1.485.7.5.4.6.1.17
The number of bytes in ICMP parameter problems that have been counted across all DLCIs.
Status: mandatory Access: read-only
OBJECT-TYPE    
  Counter  

sfrapPerfIcmpTotalTxParamProb 1.3.6.1.4.1.485.7.5.4.6.1.18
The number of bytes in ICMP parameter problems that have been counted across all DLCIs.
Status: mandatory Access: read-only
OBJECT-TYPE    
  Counter  

sfrapPerfIcmpTotalRxTimestpReq 1.3.6.1.4.1.485.7.5.4.6.1.19
The number of bytes in ICMP timestamp requests that have been counted across all DLCIs.
Status: mandatory Access: read-only
OBJECT-TYPE    
  Counter  

sfrapPerfIcmpTotalTxTimestpReq 1.3.6.1.4.1.485.7.5.4.6.1.20
The number of bytes in ICMP timestamp requests that have been counted across all DLCIs.
Status: mandatory Access: read-only
OBJECT-TYPE    
  Counter  

sfrapPerfIcmpTotalRxTimestpRep 1.3.6.1.4.1.485.7.5.4.6.1.21
The number of bytes in ICMP timestamp replies that have been counted across all DLCIs.
Status: mandatory Access: read-only
OBJECT-TYPE    
  Counter  

sfrapPerfIcmpTotalTxTimestpRep 1.3.6.1.4.1.485.7.5.4.6.1.22
The number of bytes in ICMP timestamp replies that have been counted across all DLCIs.
Status: mandatory Access: read-only
OBJECT-TYPE    
  Counter  

sfrapPerfIcmpTotalRxAddrMaskReq 1.3.6.1.4.1.485.7.5.4.6.1.23
The number of bytes in ICMP address mask requests that have been counted across all DLCIs.
Status: mandatory Access: read-only
OBJECT-TYPE    
  Counter  

sfrapPerfIcmpTotalTxAddrMaskReq 1.3.6.1.4.1.485.7.5.4.6.1.24
The number of bytes in ICMP address mask requests that have been counted across all DLCIs.
Status: mandatory Access: read-only
OBJECT-TYPE    
  Counter  

sfrapPerfIcmpTotalRxAddrMaskRep 1.3.6.1.4.1.485.7.5.4.6.1.25
The number of bytes in ICMP address mask replies that have been counted across all DLCIs.
Status: mandatory Access: read-only
OBJECT-TYPE    
  Counter  

sfrapPerfIcmpTotalTxAddrMaskRep 1.3.6.1.4.1.485.7.5.4.6.1.26
The number of bytes in ICMP address mask replies that have been counted across all DLCIs.
Status: mandatory Access: read-only
OBJECT-TYPE    
  Counter  

sfrapPerfIcmpTotalRxPktTooBig 1.3.6.1.4.1.485.7.5.4.6.1.27
The number of bytes in ICMP packet too bigs that have been counted across all DLCIs.
Status: mandatory Access: read-only
OBJECT-TYPE    
  Counter  

sfrapPerfIcmpTotalTxPktTooBig 1.3.6.1.4.1.485.7.5.4.6.1.28
The number of bytes in ICMP packet too bigs that have been counted across all DLCIs.
Status: mandatory Access: read-only
OBJECT-TYPE    
  Counter  

sfrapPerfIcmpTotalRxGmQuery 1.3.6.1.4.1.485.7.5.4.6.1.29
The number of bytes in ICMP group membership queries that have been counted across all DLCIs.
Status: mandatory Access: read-only
OBJECT-TYPE    
  Counter  

sfrapPerfIcmpTotalTxGmQuery 1.3.6.1.4.1.485.7.5.4.6.1.30
The number of bytes in ICMP group membership queries that have been counte across all DLCIs.
Status: mandatory Access: read-only
OBJECT-TYPE    
  Counter  

sfrapPerfIcmpTotalRxGmReport 1.3.6.1.4.1.485.7.5.4.6.1.31
The number of bytes in ICMP group membership reports that have been counted across all DLCIs.
Status: mandatory Access: read-only
OBJECT-TYPE    
  Counter  

sfrapPerfIcmpTotalTxGmReport 1.3.6.1.4.1.485.7.5.4.6.1.32
The number of bytes in ICMP group membership reports that have been counted across all DLCIs.
Status: mandatory Access: read-only
OBJECT-TYPE    
  Counter  

sfrapPerfIcmpTotalRxGmReduct 1.3.6.1.4.1.485.7.5.4.6.1.33
The number of bytes in ICMP group membership reductions that have been counted across all DLCIs.
Status: mandatory Access: read-only
OBJECT-TYPE    
  Counter  

sfrapPerfIcmpTotalTxGmReduct 1.3.6.1.4.1.485.7.5.4.6.1.34
The number of bytes in ICMP group membership reductions that have been counted across all DLCIs.
Status: mandatory Access: read-only
OBJECT-TYPE    
  Counter  

sfrapPerfApplicationPerDlciTable 1.3.6.1.4.1.485.7.5.4.7
The Short Term Statistics on the Application protocol for each DLCI.
Status: mandatory Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    SfrapPerfApplicationPerDlciEntry

sfrapPerfApplicationPerDlciEntry 1.3.6.1.4.1.485.7.5.4.7.1
The Application Short Term Statistics for a particular DLCI.
Status: mandatory Access: not-accessible
OBJECT-TYPE    
  SfrapPerfApplicationPerDlciEntry  

sfrapPerfApplicationPerDlciInterval 1.3.6.1.4.1.485.7.5.4.7.1.1
The Short Term statistics model maintains three intervals: current, previous, and cumulative totals. Interval duration is defined by the Short Term Timer (CfgFrPerfTimersSTInterval). (1) Currently active short term interval (2) Previously completed short term interval (3) Cumulative total since last cleared.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER current-interval(1), previous-interval(2), cumulative-counts(3)  

sfrapPerfApplicationPerDlciValue 1.3.6.1.4.1.485.7.5.4.7.1.2
The DLCI value with which the Statistics are associated.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER  

sfrapPerfApplicationPerDlciRxSnmp 1.3.6.1.4.1.485.7.5.4.7.1.3
The number of received SNMP bytes that have been counted on this DLCI.
Status: mandatory Access: read-only
OBJECT-TYPE    
  Counter  

sfrapPerfApplicationPerDlciTxSnmp 1.3.6.1.4.1.485.7.5.4.7.1.4
The number of transmitted SNMP bytes that have been counted on this DLCI.
Status: mandatory Access: read-only
OBJECT-TYPE    
  Counter  

sfrapPerfApplicationPerDlciRxSnmpTrap 1.3.6.1.4.1.485.7.5.4.7.1.5
The number of received SNMP TRAP bytes that have been counted on this DLCI.
Status: mandatory Access: read-only
OBJECT-TYPE    
  Counter  

sfrapPerfApplicationPerDlciTxSnmpTrap 1.3.6.1.4.1.485.7.5.4.7.1.6
The number of transmitted SNMP TRAP bytes that have been counted on this DLCI.
Status: mandatory Access: read-only
OBJECT-TYPE    
  Counter  

sfrapPerfApplicationPerDlciRxHttp 1.3.6.1.4.1.485.7.5.4.7.1.7
The number of received HTTP bytes that have been counted on this DLCI.
Status: mandatory Access: read-only
OBJECT-TYPE    
  Counter  

sfrapPerfApplicationPerDlciTxHttp 1.3.6.1.4.1.485.7.5.4.7.1.8
The number of transmitted HTTP bytes that have been counted on this DLCI.
Status: mandatory Access: read-only
OBJECT-TYPE    
  Counter  

sfrapPerfApplicationPerDlciRxTelnet 1.3.6.1.4.1.485.7.5.4.7.1.9
The number of received Telnet bytes that have been counted on this DLCI.
Status: mandatory Access: read-only
OBJECT-TYPE    
  Counter  

sfrapPerfApplicationPerDlciTxTelnet 1.3.6.1.4.1.485.7.5.4.7.1.10
The number of transmitted Telnet bytes that have been counted on this DLCI.
Status: mandatory Access: read-only
OBJECT-TYPE    
  Counter  

sfrapPerfApplicationPerDlciRxSmtp 1.3.6.1.4.1.485.7.5.4.7.1.11
The number of received SMTP bytes that have been counted on this DLCI.
Status: mandatory Access: read-only
OBJECT-TYPE    
  Counter  

sfrapPerfApplicationPerDlciTxSmtp 1.3.6.1.4.1.485.7.5.4.7.1.12
The number of transmitted SMTP bytes that have been counted on this DLCI.
Status: mandatory Access: read-only
OBJECT-TYPE    
  Counter  

sfrapPerfApplicationPerDlciRxFtp 1.3.6.1.4.1.485.7.5.4.7.1.13
The number of received FTP bytes that have been counted on this DLCI.
Status: mandatory Access: read-only
OBJECT-TYPE    
  Counter  

sfrapPerfApplicationPerDlciTxFtp 1.3.6.1.4.1.485.7.5.4.7.1.14
The number of transmitted FTP bytes that have been counted on this DLCI.
Status: mandatory Access: read-only
OBJECT-TYPE    
  Counter  

sfrapPerfApplicationPerDlciRxTftp 1.3.6.1.4.1.485.7.5.4.7.1.15
The number of received TFTP bytes that have been counted on this DLCI.
Status: mandatory Access: read-only
OBJECT-TYPE    
  Counter  

sfrapPerfApplicationPerDlciTxTftp 1.3.6.1.4.1.485.7.5.4.7.1.16
The number of transmitted TFTP bytes that have been counted on this DLCI.
Status: mandatory Access: read-only
OBJECT-TYPE    
  Counter  

sfrapPerfApplicationPerDlciRxCustom1 1.3.6.1.4.1.485.7.5.4.7.1.17
The number of received bytes of User Defined Protocol #1 that have been counted on this DLCI.
Status: mandatory Access: read-only
OBJECT-TYPE    
  Counter  

sfrapPerfApplicationPerDlciTxCustom1 1.3.6.1.4.1.485.7.5.4.7.1.18
The number of transmitted bytes of User Defined Protocol #1 that have been counted on this DLCI.
Status: mandatory Access: read-only
OBJECT-TYPE    
  Counter  

sfrapPerfApplicationPerDlciRxCustom2 1.3.6.1.4.1.485.7.5.4.7.1.19
The number of received bytes of User Defined Protocol #2 that have been counted on this DLCI.
Status: mandatory Access: read-only
OBJECT-TYPE    
  Counter  

sfrapPerfApplicationPerDlciTxCustom2 1.3.6.1.4.1.485.7.5.4.7.1.20
The number of transmitted bytes of User Defined Protocol #2 that have been counted on this DLCI.
Status: mandatory Access: read-only
OBJECT-TYPE    
  Counter  

sfrapPerfApplicationPerDlciRxCustom3 1.3.6.1.4.1.485.7.5.4.7.1.21
The number of received bytes of User Defined Protocol #3 that have been counted on this DLCI.
Status: mandatory Access: read-only
OBJECT-TYPE    
  Counter  

sfrapPerfApplicationPerDlciTxCustom3 1.3.6.1.4.1.485.7.5.4.7.1.22
The number of transmitted bytes of User Defined Protocol #3 that have been counted on this DLCI.
Status: mandatory Access: read-only
OBJECT-TYPE    
  Counter  

sfrapPerfApplicationPerDlciRxCustom4 1.3.6.1.4.1.485.7.5.4.7.1.23
The number of received bytes of User Defined Protocol #4 that have been counted on this DLCI.
Status: mandatory Access: read-only
OBJECT-TYPE    
  Counter  

sfrapPerfApplicationPerDlciTxCustom4 1.3.6.1.4.1.485.7.5.4.7.1.24
The number of transmitted bytes of User Defined Protocol #4 that have been counted on this DLCI.
Status: mandatory Access: read-only
OBJECT-TYPE    
  Counter  

sfrapPerfApplicationTotalTable 1.3.6.1.4.1.485.7.5.4.8
The Short Term Statistics on the Application protocol across all DLCIs.
Status: mandatory Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    SfrapPerfApplicationTotalEntry

sfrapPerfApplicationTotalEntry 1.3.6.1.4.1.485.7.5.4.8.1
The Application Short Term Statistics for a particular DLCI.
Status: mandatory Access: not-accessible
OBJECT-TYPE    
  SfrapPerfApplicationTotalEntry  

sfrapPerfApplicationTotalInterval 1.3.6.1.4.1.485.7.5.4.8.1.1
The Short Term statistics model maintains three intervals: current, previous, and cumulative totals. Interval duration is defined by the Short Term Timer (CfgFrPerfTimersSTInterval). (1) Currently active short term interval (2) Previously completed short term interval (3) Cumulative total since last cleared.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER current-interval(1), previous-interval(2), cumulative-counts(3)  

sfrapPerfApplicationTotalRxSnmp 1.3.6.1.4.1.485.7.5.4.8.1.3
The number of received SNMP bytes that have been counted across all DLCIs.
Status: mandatory Access: read-only
OBJECT-TYPE    
  Counter  

sfrapPerfApplicationTotalTxSnmp 1.3.6.1.4.1.485.7.5.4.8.1.4
The number of transmitted SNMP bytes that have been counted across all DLCIs.
Status: mandatory Access: read-only
OBJECT-TYPE    
  Counter  

sfrapPerfApplicationTotalRxSnmpTrap 1.3.6.1.4.1.485.7.5.4.8.1.5
The number of received SNMP TRAP bytes that have been counted across all DLCIs.
Status: mandatory Access: read-only
OBJECT-TYPE    
  Counter  

sfrapPerfApplicationTotalTxSnmpTrap 1.3.6.1.4.1.485.7.5.4.8.1.6
The number of transmitted SNMP TRAP bytes that have been counted across all DLCIs.
Status: mandatory Access: read-only
OBJECT-TYPE    
  Counter  

sfrapPerfApplicationTotalRxHttp 1.3.6.1.4.1.485.7.5.4.8.1.7
The number of received HTTP bytes that have been counted across all DLCIs.
Status: mandatory Access: read-only
OBJECT-TYPE    
  Counter  

sfrapPerfApplicationTotalTxHttp 1.3.6.1.4.1.485.7.5.4.8.1.8
The number of transmitted HTTP bytes that have been counted across all DLCIs.
Status: mandatory Access: read-only
OBJECT-TYPE    
  Counter  

sfrapPerfApplicationTotalRxTelnet 1.3.6.1.4.1.485.7.5.4.8.1.9
The number of received Telnet bytes that have been counted across all DLCIs.
Status: mandatory Access: read-only
OBJECT-TYPE    
  Counter  

sfrapPerfApplicationTotalTxTelnet 1.3.6.1.4.1.485.7.5.4.8.1.10
The number of transmitted Telnet bytes that have been counted across all DLCIs.
Status: mandatory Access: read-only
OBJECT-TYPE    
  Counter  

sfrapPerfApplicationTotalRxSmtp 1.3.6.1.4.1.485.7.5.4.8.1.11
The number of received SMTP bytes that have been counted across all DLCIs.
Status: mandatory Access: read-only
OBJECT-TYPE    
  Counter  

sfrapPerfApplicationTotalTxSmtp 1.3.6.1.4.1.485.7.5.4.8.1.12
The number of transmitted SMTP bytes that have been counted across all DLCIs.
Status: mandatory Access: read-only
OBJECT-TYPE    
  Counter  

sfrapPerfApplicationTotalRxFtp 1.3.6.1.4.1.485.7.5.4.8.1.13
The number of received FTP bytes that have been counted across all DLCIs.
Status: mandatory Access: read-only
OBJECT-TYPE    
  Counter  

sfrapPerfApplicationTotalTxFtp 1.3.6.1.4.1.485.7.5.4.8.1.14
The number of transmitted FTP bytes that have been counted across all DLCIs.
Status: mandatory Access: read-only
OBJECT-TYPE    
  Counter  

sfrapPerfApplicationTotalRxTftp 1.3.6.1.4.1.485.7.5.4.8.1.15
The number of received TFTP bytes that have been counted across all DLCIs.
Status: mandatory Access: read-only
OBJECT-TYPE    
  Counter  

sfrapPerfApplicationTotalTxTftp 1.3.6.1.4.1.485.7.5.4.8.1.16
The number of transmitted TFTP bytes that have been counted across all DLCIs.
Status: mandatory Access: read-only
OBJECT-TYPE    
  Counter  

sfrapPerfApplicationTotalRxCustom1 1.3.6.1.4.1.485.7.5.4.8.1.17
The number of received bytes of User Defined Protocol #1 that have been counted across all DLCIs.
Status: mandatory Access: read-only
OBJECT-TYPE    
  Counter  

sfrapPerfApplicationTotalTxCustom1 1.3.6.1.4.1.485.7.5.4.8.1.18
The number of transmitted bytes of User Defined Protocol #1 that have been counted across all DLCIs.
Status: mandatory Access: read-only
OBJECT-TYPE    
  Counter  

sfrapPerfApplicationTotalRxCustom2 1.3.6.1.4.1.485.7.5.4.8.1.19
The number of received bytes of User Defined Protocol #2 that have been counted across all DLCIs.
Status: mandatory Access: read-only
OBJECT-TYPE    
  Counter  

sfrapPerfApplicationTotalTxCustom2 1.3.6.1.4.1.485.7.5.4.8.1.20
The number of transmitted bytes of User Defined Protocol #2 that have been counted across all DLCIs.
Status: mandatory Access: read-only
OBJECT-TYPE    
  Counter  

sfrapPerfApplicationTotalRxCustom3 1.3.6.1.4.1.485.7.5.4.8.1.21
The number of received bytes of User Defined Protocol #3 that have been counted across all DLCIs.
Status: mandatory Access: read-only
OBJECT-TYPE    
  Counter  

sfrapPerfApplicationTotalTxCustom3 1.3.6.1.4.1.485.7.5.4.8.1.22
The number of transmitted bytes of User Defined Protocol #3 that have been counted across all DLCIs.
Status: mandatory Access: read-only
OBJECT-TYPE    
  Counter  

sfrapPerfApplicationTotalRxCustom4 1.3.6.1.4.1.485.7.5.4.8.1.23
The number of received bytes of User Defined Protocol #4 that have been counted across all DLCIs.
Status: mandatory Access: read-only
OBJECT-TYPE    
  Counter  

sfrapPerfApplicationTotalTxCustom4 1.3.6.1.4.1.485.7.5.4.8.1.24
The number of transmitted bytes of User Defined Protocol #4 that have been counted across all DLCIs.
Status: mandatory Access: read-only
OBJECT-TYPE    
  Counter  

sfrapPerfRoutingPerDlciTable 1.3.6.1.4.1.485.7.5.4.9
The Short Term Statistics on the Routing protocol for each DLCI.
Status: mandatory Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    SfrapPerfRoutingPerDlciEntry

sfrapPerfRoutingPerDlciEntry 1.3.6.1.4.1.485.7.5.4.9.1
The Routing Short Term Statistics for a particular DLCI.
Status: mandatory Access: not-accessible
OBJECT-TYPE    
  SfrapPerfRoutingPerDlciEntry  

sfrapPerfRoutingPerDlciInterval 1.3.6.1.4.1.485.7.5.4.9.1.1
The Short Term statistics model maintains three intervals: current, previous, and cumulative totals. Interval duration is defined by the Short Term Timer (CfgFrPerfTimersSTInterval). (1) Currently active short term interval (2) Previously completed short term interval (3) Cumulative total since last cleared.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER current-interval(1), previous-interval(2), cumulative-counts(3)  

sfrapPerfRoutingPerDlciValue 1.3.6.1.4.1.485.7.5.4.9.1.2
The DLCI value with which the Statistics are associated.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER  

sfrapPerfRoutingPerDlciRxOspf 1.3.6.1.4.1.485.7.5.4.9.1.3
The number of received OSPF bytes that have been counted on this DLCI.
Status: mandatory Access: read-only
OBJECT-TYPE    
  Counter  

sfrapPerfRoutingPerDlciTxOspf 1.3.6.1.4.1.485.7.5.4.9.1.4
The number of transmitted OSPF bytes that have been counted on this DLCI.
Status: mandatory Access: read-only
OBJECT-TYPE    
  Counter  

sfrapPerfRoutingPerDlciRxRip 1.3.6.1.4.1.485.7.5.4.9.1.5
The number of received RIP bytes that have been counted on this DLCI.
Status: mandatory Access: read-only
OBJECT-TYPE    
  Counter  

sfrapPerfRoutingPerDlciTxRip 1.3.6.1.4.1.485.7.5.4.9.1.6
The number of transmitted RIP bytes that have been counted on this DLCI.
Status: mandatory Access: read-only
OBJECT-TYPE    
  Counter  

sfrapPerfRoutingPerDlciRxNetbios 1.3.6.1.4.1.485.7.5.4.9.1.7
The number of received Netbios bytes that have been counted on this DLCI.
Status: mandatory Access: read-only
OBJECT-TYPE    
  Counter  

sfrapPerfRoutingPerDlciTxNetbios 1.3.6.1.4.1.485.7.5.4.9.1.8
The number of transmitted Netbios bytes that have been counted on this DLCI.
Status: mandatory Access: read-only
OBJECT-TYPE    
  Counter  

sfrapPerfRoutingTotalTable 1.3.6.1.4.1.485.7.5.4.10
The Short Term Statistics on the Routing protocol across all DLCIs.
Status: mandatory Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    SfrapPerfRoutingTotalEntry

sfrapPerfRoutingTotalEntry 1.3.6.1.4.1.485.7.5.4.10.1
The Routing Short Term Statistics for a particular DLCI.
Status: mandatory Access: not-accessible
OBJECT-TYPE    
  SfrapPerfRoutingTotalEntry  

sfrapPerfRoutingTotalInterval 1.3.6.1.4.1.485.7.5.4.10.1.1
The Short Term statistics model maintains three intervals: current, previous, and cumulative totals. Interval duration is defined by the Short Term Timer (CfgFrPerfTimersSTInterval). (1) Currently active short term interval (2) Previously completed short term interval (3) Cumulative total since last cleared.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER current-interval(1), previous-interval(2), cumulative-counts(3)  

sfrapPerfRoutingTotalRxOspf 1.3.6.1.4.1.485.7.5.4.10.1.3
The number of received OSPF bytes that have been counted across all DLCIs.
Status: mandatory Access: read-only
OBJECT-TYPE    
  Counter  

sfrapPerfRoutingTotalTxOspf 1.3.6.1.4.1.485.7.5.4.10.1.4
The number of transmitted OSPF bytes that have been counted across all DLCIs.
Status: mandatory Access: read-only
OBJECT-TYPE    
  Counter  

sfrapPerfRoutingTotalRxRip 1.3.6.1.4.1.485.7.5.4.10.1.5
The number of received RIP bytes that have been counted across all DLCIs.
Status: mandatory Access: read-only
OBJECT-TYPE    
  Counter  

sfrapPerfRoutingTotalTxRip 1.3.6.1.4.1.485.7.5.4.10.1.6
The number of transmitted RIP bytes that have been counted across all DLCIs.
Status: mandatory Access: read-only
OBJECT-TYPE    
  Counter  

sfrapPerfRoutingTotalRxNetbios 1.3.6.1.4.1.485.7.5.4.10.1.7
The number of received Netbios bytes that have been counted across all DLCIs.
Status: mandatory Access: read-only
OBJECT-TYPE    
  Counter  

sfrapPerfRoutingTotalTxNetbios 1.3.6.1.4.1.485.7.5.4.10.1.8
The number of transmitted Netbios bytes that have been counted across all DLCIs.
Status: mandatory Access: read-only
OBJECT-TYPE    
  Counter  

sfrapPerfIpxPerDlciTable 1.3.6.1.4.1.485.7.5.4.11
Short Term Statistics on the IPX protocol for each DLCI.
Status: mandatory Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    SfrapPerfIpxPerDlciEntry

sfrapPerfIpxPerDlciEntry 1.3.6.1.4.1.485.7.5.4.11.1
The IPX Short Term Statistics for a particular DLCI.
Status: mandatory Access: not-accessible
OBJECT-TYPE    
  SfrapPerfIpxPerDlciEntry  

sfrapPerfIpxPerDlciInterval 1.3.6.1.4.1.485.7.5.4.11.1.1
The Short Term statistics model maintains three intervals: current, previous, and cumulative totals. Interval duration is defined by the Short Term Timer (CfgFrPerfTimersSTInterval). (1) Currently active short term interval (2) Previously completed short term interval (3) Cumulative total since last cleared.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER current-interval(1), previous-interval(2), cumulative-counts(3)  

sfrapPerfIpxPerDlciValue 1.3.6.1.4.1.485.7.5.4.11.1.2
The DLCI value in which the Statistics are associated.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER  

sfrapPerfIpxPerDlciRxTotal 1.3.6.1.4.1.485.7.5.4.11.1.3
The total number of IPX bytes that have been counted on this DLCI.
Status: mandatory Access: read-only
OBJECT-TYPE    
  Counter  

sfrapPerfIpxPerDlciTxTotal 1.3.6.1.4.1.485.7.5.4.11.1.4
The total number of IPX bytes that have been counted on this DLCI.
Status: mandatory Access: read-only
OBJECT-TYPE    
  Counter  

sfrapPerfIpxPerDlciRxSpx 1.3.6.1.4.1.485.7.5.4.11.1.5
The number of SPX over IPX bytes that have been counted on this DLCI.
Status: mandatory Access: read-only
OBJECT-TYPE    
  Counter  

sfrapPerfIpxPerDlciTxSpx 1.3.6.1.4.1.485.7.5.4.11.1.6
The number of SPX over IPX bytes that have been counted on this DLCI.
Status: mandatory Access: read-only
OBJECT-TYPE    
  Counter  

sfrapPerfIpxPerDlciRxNcp 1.3.6.1.4.1.485.7.5.4.11.1.7
The number of NCP over IPX bytes that have been counted on this DLCI.
Status: mandatory Access: read-only
OBJECT-TYPE    
  Counter  

sfrapPerfIpxPerDlciTxNcp 1.3.6.1.4.1.485.7.5.4.11.1.8
The number of NCP over IPX bytes that have been counted on this DLCI.
Status: mandatory Access: read-only
OBJECT-TYPE    
  Counter  

sfrapPerfIpxPerDlciRxSap 1.3.6.1.4.1.485.7.5.4.11.1.9
The number of SAP over IPX bytes that have been counted on this DLCI.
Status: mandatory Access: read-only
OBJECT-TYPE    
  Counter  

sfrapPerfIpxPerDlciTxSap 1.3.6.1.4.1.485.7.5.4.11.1.10
The number of SAP over IPX bytes that have been counted on this DLCI.
Status: mandatory Access: read-only
OBJECT-TYPE    
  Counter  

sfrapPerfIpxPerDlciRxRip 1.3.6.1.4.1.485.7.5.4.11.1.11
The number of RIP over IPX bytes that have been counted on this DLCI.
Status: mandatory Access: read-only
OBJECT-TYPE    
  Counter  

sfrapPerfIpxPerDlciTxRip 1.3.6.1.4.1.485.7.5.4.11.1.12
The number of RIP over IPX bytes that have been counted on this DLCI.
Status: mandatory Access: read-only
OBJECT-TYPE    
  Counter  

sfrapPerfIpxPerDlciRxNetbios 1.3.6.1.4.1.485.7.5.4.11.1.13
The number of NETBIOS over IPX bytes that have been counted on this DLCI.
Status: mandatory Access: read-only
OBJECT-TYPE    
  Counter  

sfrapPerfIpxPerDlciTxNetbios 1.3.6.1.4.1.485.7.5.4.11.1.14
The number of NETBIOS over IPX bytes that have been counted on this DLCI.
Status: mandatory Access: read-only
OBJECT-TYPE    
  Counter  

sfrapPerfIpxPerDlciRxOther 1.3.6.1.4.1.485.7.5.4.11.1.15
The number of received bytes on this DLCI from protocols over IPX that are not counted elsewhere in this table.
Status: mandatory Access: read-only
OBJECT-TYPE    
  Counter  

sfrapPerfIpxPerDlciTxOther 1.3.6.1.4.1.485.7.5.4.11.1.16
The number of transmitted bytes on this DLCI from protocols over IPX that are not counted elsewhere in this table.
Status: mandatory Access: read-only
OBJECT-TYPE    
  Counter  

sfrapPerfIpxTotalTable 1.3.6.1.4.1.485.7.5.4.12
Short Term Statistics on the IPX protocol across all DLCIs.
Status: mandatory Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    SfrapPerfIpxTotalEntry

sfrapPerfIpxTotalEntry 1.3.6.1.4.1.485.7.5.4.12.1
The IPX Short Term Statistics for a particular DLCI.
Status: mandatory Access: not-accessible
OBJECT-TYPE    
  SfrapPerfIpxTotalEntry  

sfrapPerfIpxTotalInterval 1.3.6.1.4.1.485.7.5.4.12.1.1
The Short Term statistics model maintains three intervals: current, previous, and cumulative totals. Interval duration is defined by the Short Term Timer (CfgFrPerfTimersSTInterval). (1) Currently active short term interval (2) Previously completed short term interval (3) Cumulative total since last cleared.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER current-interval(1), previous-interval(2), cumulative-counts(3)  

sfrapPerfIpxTotalRxTotal 1.3.6.1.4.1.485.7.5.4.12.1.3
The total number of IPX bytes that have been counted across all DLCIs.
Status: mandatory Access: read-only
OBJECT-TYPE    
  Counter  

sfrapPerfIpxTotalTxTotal 1.3.6.1.4.1.485.7.5.4.12.1.4
The total number of IPX bytes that have been counted across all DLCIs.
Status: mandatory Access: read-only
OBJECT-TYPE    
  Counter  

sfrapPerfIpxTotalRxSpx 1.3.6.1.4.1.485.7.5.4.12.1.5
The number of SPX over IPX bytes that have been counted across all DLCIs.
Status: mandatory Access: read-only
OBJECT-TYPE    
  Counter  

sfrapPerfIpxTotalTxSpx 1.3.6.1.4.1.485.7.5.4.12.1.6
The number of SPX over IPX bytes that have been counted across all DLCIs.
Status: mandatory Access: read-only
OBJECT-TYPE    
  Counter  

sfrapPerfIpxTotalRxNcp 1.3.6.1.4.1.485.7.5.4.12.1.7
The number of NCP over IPX bytes that have been counted across all DLCIs.
Status: mandatory Access: read-only
OBJECT-TYPE    
  Counter  

sfrapPerfIpxTotalTxNcp 1.3.6.1.4.1.485.7.5.4.12.1.8
The number of NCP over IPX bytes that have been counted across all DLCIs.
Status: mandatory Access: read-only
OBJECT-TYPE    
  Counter  

sfrapPerfIpxTotalRxSap 1.3.6.1.4.1.485.7.5.4.12.1.9
The number of SAP over IPX bytes that have been counted across all DLCIs.
Status: mandatory Access: read-only
OBJECT-TYPE    
  Counter  

sfrapPerfIpxTotalTxSap 1.3.6.1.4.1.485.7.5.4.12.1.10
The number of SAP over IPX bytes that have been counted across all DLCIs.
Status: mandatory Access: read-only
OBJECT-TYPE    
  Counter  

sfrapPerfIpxTotalRxRip 1.3.6.1.4.1.485.7.5.4.12.1.11
The number of RIP over IPX bytes that have been counted across all DLCIs.
Status: mandatory Access: read-only
OBJECT-TYPE    
  Counter  

sfrapPerfIpxTotalTxRip 1.3.6.1.4.1.485.7.5.4.12.1.12
The number of RIP over IPX bytes that have been counted across all DLCIs.
Status: mandatory Access: read-only
OBJECT-TYPE    
  Counter  

sfrapPerfIpxTotalRxNetbios 1.3.6.1.4.1.485.7.5.4.12.1.13
The number of NETBIOS over IPX bytes that have been counted across all DLCIs.
Status: mandatory Access: read-only
OBJECT-TYPE    
  Counter  

sfrapPerfIpxTotalTxNetbios 1.3.6.1.4.1.485.7.5.4.12.1.14
The number of NETBIOS over IPX bytes that have been counted across all DLCIs.
Status: mandatory Access: read-only
OBJECT-TYPE    
  Counter  

sfrapPerfIpxTotalRxOther 1.3.6.1.4.1.485.7.5.4.12.1.15
The number of received bytes across all DLCIs from protocols over IPX that are not counted elsewhere in this table.
Status: mandatory Access: read-only
OBJECT-TYPE    
  Counter  

sfrapPerfIpxTotalTxOther 1.3.6.1.4.1.485.7.5.4.12.1.16
The number of transmitted bytes across all DLCIs from protocols over IPX that are not counted elsewhere in this table.
Status: mandatory Access: read-only
OBJECT-TYPE    
  Counter  

sfrapPerfSnaPerDlciTable 1.3.6.1.4.1.485.7.5.4.13
Short Term Statistics on the SNA protocol for each DLCI.
Status: mandatory Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    SfrapPerfSnaPerDlciEntry

sfrapPerfSnaPerDlciEntry 1.3.6.1.4.1.485.7.5.4.13.1
The SNA Short Term Statistics for a particular DLCI.
Status: mandatory Access: not-accessible
OBJECT-TYPE    
  SfrapPerfSnaPerDlciEntry  

sfrapPerfSnaPerDlciInterval 1.3.6.1.4.1.485.7.5.4.13.1.1
The Short Term statistics model maintains three intervals: current, previous, and cumulative totals. Interval duration is defined by the Short Term Timer (CfgFrPerfTimersSTInterval). (1) Currently active short term interval (2) Previously completed short term interval (3) Cumulative total since last cleared.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER current-interval(1), previous-interval(2), cumulative-counts(3)  

sfrapPerfSnaPerDlciValue 1.3.6.1.4.1.485.7.5.4.13.1.2
The DLCI value in which the Statistics are associated.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER  

sfrapPerfSnaPerDlciRxTotal 1.3.6.1.4.1.485.7.5.4.13.1.3
The total number of SNA bytes that have been counted on this DLCI.
Status: mandatory Access: read-only
OBJECT-TYPE    
  Counter  

sfrapPerfSnaPerDlciTxTotal 1.3.6.1.4.1.485.7.5.4.13.1.4
The total number of SNA bytes that have been counted on this DLCI.
Status: mandatory Access: read-only
OBJECT-TYPE    
  Counter  

sfrapPerfSnaPerDlciRxSubarea 1.3.6.1.4.1.485.7.5.4.13.1.5
The number of SNA Subarea bytes that have been counted on this DLCI.
Status: mandatory Access: read-only
OBJECT-TYPE    
  Counter  

sfrapPerfSnaPerDlciTxSubarea 1.3.6.1.4.1.485.7.5.4.13.1.6
The number of SNA Subarea bytes that have been counted on this DLCI.
Status: mandatory Access: read-only
OBJECT-TYPE    
  Counter  

sfrapPerfSnaPerDlciRxPeriph 1.3.6.1.4.1.485.7.5.4.13.1.7
The number of SNA Periph bytes that have been counted on this DLCI.
Status: mandatory Access: read-only
OBJECT-TYPE    
  Counter  

sfrapPerfSnaPerDlciTxPeriph 1.3.6.1.4.1.485.7.5.4.13.1.8
The number of SNA Periph bytes that have been counted on this DLCI.
Status: mandatory Access: read-only
OBJECT-TYPE    
  Counter  

sfrapPerfSnaPerDlciRxAppn 1.3.6.1.4.1.485.7.5.4.13.1.9
The number of SNA Appn bytes that have been counted on this DLCI.
Status: mandatory Access: read-only
OBJECT-TYPE    
  Counter  

sfrapPerfSnaPerDlciTxAppn 1.3.6.1.4.1.485.7.5.4.13.1.10
The number of SNA Appn bytes that have been counted on this DLCI.
Status: mandatory Access: read-only
OBJECT-TYPE    
  Counter  

sfrapPerfSnaPerDlciRxNetbios 1.3.6.1.4.1.485.7.5.4.13.1.11
The number of SNA Netbios bytes that have been counted on this DLCI.
Status: mandatory Access: read-only
OBJECT-TYPE    
  Counter  

sfrapPerfSnaPerDlciTxNetbios 1.3.6.1.4.1.485.7.5.4.13.1.12
The number of SNA Netbios bytes that have been counted on this DLCI.
Status: mandatory Access: read-only
OBJECT-TYPE    
  Counter  

sfrapPerfSnaPerDlciRxOther 1.3.6.1.4.1.485.7.5.4.13.1.13
The number of received bytes on this DLCI from protocols over SNA that are not counted elsewhere in this table.
Status: mandatory Access: read-only
OBJECT-TYPE    
  Counter  

sfrapPerfSnaPerDlciTxOther 1.3.6.1.4.1.485.7.5.4.13.1.14
The number of transmitted bytes on this DLCI from protocols over SNA that are not counted elsewhere in this table.
Status: mandatory Access: read-only
OBJECT-TYPE    
  Counter  

sfrapPerfSnaTotalTable 1.3.6.1.4.1.485.7.5.4.14
Short Term Statistics on the SNA protocol across all DLCIs.
Status: mandatory Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    SfrapPerfSnaTotalEntry

sfrapPerfSnaTotalEntry 1.3.6.1.4.1.485.7.5.4.14.1
The SNA Short Term Statistics for a particular DLCI.
Status: mandatory Access: not-accessible
OBJECT-TYPE    
  SfrapPerfSnaTotalEntry  

sfrapPerfSnaTotalInterval 1.3.6.1.4.1.485.7.5.4.14.1.1
The Short Term statistics model maintains three intervals: current, previous, and cumulative totals. Interval duration is defined by the Short Term Timer (CfgFrPerfTimersSTInterval). (1) Currently active short term interval (2) Previously completed short term interval (3) Cumulative total since last cleared.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER current-interval(1), previous-interval(2), cumulative-counts(3)  

sfrapPerfSnaTotalRxTotal 1.3.6.1.4.1.485.7.5.4.14.1.3
The total number of SNA bytes that have been counted across all DLCIs.
Status: mandatory Access: read-only
OBJECT-TYPE    
  Counter  

sfrapPerfSnaTotalTxTotal 1.3.6.1.4.1.485.7.5.4.14.1.4
The total number of SNA bytes that have been counted across all DLCIs.
Status: mandatory Access: read-only
OBJECT-TYPE    
  Counter  

sfrapPerfSnaTotalRxSubarea 1.3.6.1.4.1.485.7.5.4.14.1.5
The number of SNA Subarea bytes that have been counted across all DLCIs.
Status: mandatory Access: read-only
OBJECT-TYPE    
  Counter  

sfrapPerfSnaTotalTxSubarea 1.3.6.1.4.1.485.7.5.4.14.1.6
The number of SNA Subarea bytes that have been counted across all DLCIs.
Status: mandatory Access: read-only
OBJECT-TYPE    
  Counter  

sfrapPerfSnaTotalRxPeriph 1.3.6.1.4.1.485.7.5.4.14.1.7
The number of SNA Periph bytes that have been counted across all DLCIs.
Status: mandatory Access: read-only
OBJECT-TYPE    
  Counter  

sfrapPerfSnaTotalTxPeriph 1.3.6.1.4.1.485.7.5.4.14.1.8
The number of SNA Periph bytes that have been counted across all DLCIs.
Status: mandatory Access: read-only
OBJECT-TYPE    
  Counter  

sfrapPerfSnaTotalRxAppn 1.3.6.1.4.1.485.7.5.4.14.1.9
The number of SNA Appn bytes that have been counted across all DLCIs.
Status: mandatory Access: read-only
OBJECT-TYPE    
  Counter  

sfrapPerfSnaTotalTxAppn 1.3.6.1.4.1.485.7.5.4.14.1.10
The number of SNA Appn bytes that have been counted across all DLCIs.
Status: mandatory Access: read-only
OBJECT-TYPE    
  Counter  

sfrapPerfSnaTotalRxNetbios 1.3.6.1.4.1.485.7.5.4.14.1.11
The number of SNA Netbios bytes that have been counted across all DLCIs.
Status: mandatory Access: read-only
OBJECT-TYPE    
  Counter  

sfrapPerfSnaTotalTxNetbios 1.3.6.1.4.1.485.7.5.4.14.1.12
The number of SNA Netbios bytes that have been counted across all DLCIs.
Status: mandatory Access: read-only
OBJECT-TYPE    
  Counter  

sfrapPerfSnaTotalRxOther 1.3.6.1.4.1.485.7.5.4.14.1.13
The number of received bytes across all DLCIs from protocols over SNA that are not counted elsewhere in this table.
Status: mandatory Access: read-only
OBJECT-TYPE    
  Counter  

sfrapPerfSnaTotalTxOther 1.3.6.1.4.1.485.7.5.4.14.1.14
The number of transmitted bytes across all DLCIs from protocols over SNA that are not counted elsewhere in this table.
Status: mandatory Access: read-only
OBJECT-TYPE    
  Counter  

sfrapPerfArpPerDlciTable 1.3.6.1.4.1.485.7.5.4.15
Short Term Statistics on the ARP protocol for each DLCI.
Status: mandatory Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    SfrapPerfArpPerDlciEntry

sfrapPerfArpPerDlciEntry 1.3.6.1.4.1.485.7.5.4.15.1
The ARP Short Term Statistics for a particular DLCI.
Status: mandatory Access: not-accessible
OBJECT-TYPE    
  SfrapPerfArpPerDlciEntry  

sfrapPerfArpPerDlciInterval 1.3.6.1.4.1.485.7.5.4.15.1.1
The Short Term statistics model maintains three intervals: current, previous, and cumulative totals. Interval duration is defined by the Short Term Timer (CfgFrPerfTimersSTInterval). (1) Currently active short term interval (2) Previously completed short term interval (3) Cumulative total since last cleared.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER current-interval(1), previous-interval(2), cumulative-counts(3)  

sfrapPerfArpPerDlciValue 1.3.6.1.4.1.485.7.5.4.15.1.2
The DLCI value in which the Statistics are associated.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER  

sfrapPerfArpPerDlciRxTotal 1.3.6.1.4.1.485.7.5.4.15.1.3
The total number of ARP bytes that have been counted on this DLCI.
Status: mandatory Access: read-only
OBJECT-TYPE    
  Counter  

sfrapPerfArpPerDlciTxTotal 1.3.6.1.4.1.485.7.5.4.15.1.4
The total number of ARP bytes that have been counted on this DLCI.
Status: mandatory Access: read-only
OBJECT-TYPE    
  Counter  

sfrapPerfArpPerDlciRxArpReq 1.3.6.1.4.1.485.7.5.4.15.1.5
The number of ARP request bytes that have been counted on this DLCI.
Status: mandatory Access: read-only
OBJECT-TYPE    
  Counter  

sfrapPerfArpPerDlciTxArpReq 1.3.6.1.4.1.485.7.5.4.15.1.6
The number of ARP request bytes that have been counted on this DLCI.
Status: mandatory Access: read-only
OBJECT-TYPE    
  Counter  

sfrapPerfArpPerDlciRxArpRep 1.3.6.1.4.1.485.7.5.4.15.1.7
The number of ARP reply bytes that have been counted on this DLCI.
Status: mandatory Access: read-only
OBJECT-TYPE    
  Counter  

sfrapPerfArpPerDlciTxArpRep 1.3.6.1.4.1.485.7.5.4.15.1.8
The number of ARP reply bytes that have been counted on this DLCI.
Status: mandatory Access: read-only
OBJECT-TYPE    
  Counter  

sfrapPerfArpPerDlciRxRarpReq 1.3.6.1.4.1.485.7.5.4.15.1.9
The number of RARP request bytes that have been counted on this DLCI.
Status: mandatory Access: read-only
OBJECT-TYPE    
  Counter  

sfrapPerfArpPerDlciTxRarpReq 1.3.6.1.4.1.485.7.5.4.15.1.10
The number of RARP request bytes that have been counted on this DLCI.
Status: mandatory Access: read-only
OBJECT-TYPE    
  Counter  

sfrapPerfArpPerDlciRxRarpRep 1.3.6.1.4.1.485.7.5.4.15.1.11
The number of RARP reply bytes that have been counted on this DLCI.
Status: mandatory Access: read-only
OBJECT-TYPE    
  Counter  

sfrapPerfArpPerDlciTxRarpRep 1.3.6.1.4.1.485.7.5.4.15.1.12
The number of RARP reply bytes that have been counted on this DLCI.
Status: mandatory Access: read-only
OBJECT-TYPE    
  Counter  

sfrapPerfArpPerDlciRxInarpReq 1.3.6.1.4.1.485.7.5.4.15.1.13
The number of INARP request bytes that have been counted on this DLCI.
Status: mandatory Access: read-only
OBJECT-TYPE    
  Counter  

sfrapPerfArpPerDlciTxInarpReq 1.3.6.1.4.1.485.7.5.4.15.1.14
The number of INARP request bytes that have been counted on this DLCI.
Status: mandatory Access: read-only
OBJECT-TYPE    
  Counter  

sfrapPerfArpPerDlciRxInarpRep 1.3.6.1.4.1.485.7.5.4.15.1.15
The number of INARP reply bytes that have been counted on this DLCI.
Status: mandatory Access: read-only
OBJECT-TYPE    
  Counter  

sfrapPerfArpPerDlciTxInarpRep 1.3.6.1.4.1.485.7.5.4.15.1.16
The number of INARP reply bytes that have been counted on this DLCI.
Status: mandatory Access: read-only
OBJECT-TYPE    
  Counter  

sfrapPerfArpPerDlciRxOther 1.3.6.1.4.1.485.7.5.4.15.1.17
The number of received bytes on this DLCI from ARP message types that are not counted elsewhere in this table.
Status: mandatory Access: read-only
OBJECT-TYPE    
  Counter  

sfrapPerfArpPerDlciTxOther 1.3.6.1.4.1.485.7.5.4.15.1.18
The number of transmitted bytes on this DLCI from ARP message types that are not counted elsewhere in this table.
Status: mandatory Access: read-only
OBJECT-TYPE    
  Counter  

sfrapPerfArpTotalTable 1.3.6.1.4.1.485.7.5.4.16
Short Term Statistics on the ARP protocol across all DLCIs.
Status: mandatory Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    SfrapPerfArpTotalEntry

sfrapPerfArpTotalEntry 1.3.6.1.4.1.485.7.5.4.16.1
The ARP Short Term Statistics for a particular DLCI.
Status: mandatory Access: not-accessible
OBJECT-TYPE    
  SfrapPerfArpTotalEntry  

sfrapPerfArpTotalInterval 1.3.6.1.4.1.485.7.5.4.16.1.1
The Short Term statistics model maintains three intervals: current, previous, and cumulative totals. Interval duration is defined by the Short Term Timer (CfgFrPerfTimersSTInterval). (1) Currently active short term interval (2) Previously completed short term interval (3) Cumulative total since last cleared.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER current-interval(1), previous-interval(2), cumulative-counts(3)  

sfrapPerfArpTotalRxTotal 1.3.6.1.4.1.485.7.5.4.16.1.3
The total number of ARP bytes that have been counted across all DLCIs.
Status: mandatory Access: read-only
OBJECT-TYPE    
  Counter  

sfrapPerfArpTotalTxTotal 1.3.6.1.4.1.485.7.5.4.16.1.4
The total number of ARP bytes that have been counted across all DLCIs.
Status: mandatory Access: read-only
OBJECT-TYPE    
  Counter  

sfrapPerfArpTotalRxArpReq 1.3.6.1.4.1.485.7.5.4.16.1.5
The number of ARP request bytes that have been counted across all DLCIs.
Status: mandatory Access: read-only
OBJECT-TYPE    
  Counter  

sfrapPerfArpTotalTxArpReq 1.3.6.1.4.1.485.7.5.4.16.1.6
The number of ARP request bytes that have been counted across all DLCIs.
Status: mandatory Access: read-only
OBJECT-TYPE    
  Counter  

sfrapPerfArpTotalRxArpRep 1.3.6.1.4.1.485.7.5.4.16.1.7
The number of ARP reply bytes that have been counted across all DLCIs.
Status: mandatory Access: read-only
OBJECT-TYPE    
  Counter  

sfrapPerfArpTotalTxArpRep 1.3.6.1.4.1.485.7.5.4.16.1.8
The number of ARP reply bytes that have been counted across all DLCIs.
Status: mandatory Access: read-only
OBJECT-TYPE    
  Counter  

sfrapPerfArpTotalRxRarpReq 1.3.6.1.4.1.485.7.5.4.16.1.9
The number of RARP request bytes that have been counted across all DLCIs.
Status: mandatory Access: read-only
OBJECT-TYPE    
  Counter  

sfrapPerfArpTotalTxRarpReq 1.3.6.1.4.1.485.7.5.4.16.1.10
The number of RARP request bytes that have been counted across all DLCIs.
Status: mandatory Access: read-only
OBJECT-TYPE    
  Counter  

sfrapPerfArpTotalRxRarpRep 1.3.6.1.4.1.485.7.5.4.16.1.11
The number of RARP reply bytes that have been counted across all DLCIs.
Status: mandatory Access: read-only
OBJECT-TYPE    
  Counter  

sfrapPerfArpTotalTxRarpRep 1.3.6.1.4.1.485.7.5.4.16.1.12
The number of RARP reply bytes that have been counted across all DLCIs.
Status: mandatory Access: read-only
OBJECT-TYPE    
  Counter  

sfrapPerfArpTotalRxInarpReq 1.3.6.1.4.1.485.7.5.4.16.1.13
The number of INARP request bytes that have been counted across all DLCIs.
Status: mandatory Access: read-only
OBJECT-TYPE    
  Counter  

sfrapPerfArpTotalTxInarpReq 1.3.6.1.4.1.485.7.5.4.16.1.14
The number of INARP request bytes that have been counted across all DLCIs.
Status: mandatory Access: read-only
OBJECT-TYPE    
  Counter  

sfrapPerfArpTotalRxInarpRep 1.3.6.1.4.1.485.7.5.4.16.1.15
The number of INARP reply bytes that have been counted across all DLCIs.
Status: mandatory Access: read-only
OBJECT-TYPE    
  Counter  

sfrapPerfArpTotalTxInarpRep 1.3.6.1.4.1.485.7.5.4.16.1.16
The number of INARP reply bytes that have been counted across all DLCIs.
Status: mandatory Access: read-only
OBJECT-TYPE    
  Counter  

sfrapPerfArpTotalRxOther 1.3.6.1.4.1.485.7.5.4.16.1.17
The number of received bytes across all DLCIs from ARP message types that are not counted elsewhere in this table.
Status: mandatory Access: read-only
OBJECT-TYPE    
  Counter  

sfrapPerfArpTotalTxOther 1.3.6.1.4.1.485.7.5.4.16.1.18
The number of transmitted bytes across all DLCIs from ARP message types that are not counted elsewhere in this table.
Status: mandatory Access: read-only
OBJECT-TYPE    
  Counter  

sfrapPerfLmiPerDlciTable 1.3.6.1.4.1.485.7.5.4.17
Short Term Statistics on LMI protocol for each DLCI.
Status: mandatory Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    SfrapPerfLmiPerDlciEntry

sfrapPerfLmiPerDlciEntry 1.3.6.1.4.1.485.7.5.4.17.1
The LMI Short Term Statistics for a particular DLCI.
Status: mandatory Access: not-accessible
OBJECT-TYPE    
  SfrapPerfLmiPerDlciEntry  

sfrapPerfLmiPerDlciInterval 1.3.6.1.4.1.485.7.5.4.17.1.1
The Short Term statistics model maintains three intervals: current, previous, and cumulative totals. Interval duration is defined by the Short Term Timer (CfgFrPerfTimersSTInterval). (1) Currently active short term interval (2) Previously completed short term interval (3) Cumulative total since last cleared.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER current-interval(1), previous-interval(2), cumulative-counts(3)  

sfrapPerfLmiPerDlciValue 1.3.6.1.4.1.485.7.5.4.17.1.2
The DLCI value with which the Statistics are associated.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER  

sfrapPerfLmiPerDlciRxTotalByteCnt 1.3.6.1.4.1.485.7.5.4.17.1.3
The total number of received LMI bytes counted on this DLCI.
Status: mandatory Access: read-only
OBJECT-TYPE    
  Counter  

sfrapPerfLmiPerDlciTxTotalByteCnt 1.3.6.1.4.1.485.7.5.4.17.1.4
The total number of transmitted LMI bytes counted on this DLCI.
Status: mandatory Access: read-only
OBJECT-TYPE    
  Counter  

sfrapPerfLmiPerDlciRxLivoEnqByteCnt 1.3.6.1.4.1.485.7.5.4.17.1.5
The number of bytes received in Link Integrity Verification Only (LIVO) enquiries on this DLCI.
Status: mandatory Access: read-only
OBJECT-TYPE    
  Counter  

sfrapPerfLmiPerDlciTxLivoEnqByteCnt 1.3.6.1.4.1.485.7.5.4.17.1.6
The number of bytes transmitted in Link Integrity Verification Only (LIVO) enquiries on this DLCI.
Status: mandatory Access: read-only
OBJECT-TYPE    
  Counter  

sfrapPerfLmiPerDlciRxLivoStatByteCnt 1.3.6.1.4.1.485.7.5.4.17.1.7
The number of bytes received in Link Integrity Verification Only (LIVO) statuses on this DLCI.
Status: mandatory Access: read-only
OBJECT-TYPE    
  Counter  

sfrapPerfLmiPerDlciTxLivoStatByteCnt 1.3.6.1.4.1.485.7.5.4.17.1.8
The number of bytes transmitted in Link Integrity Verification Only (LIVO) statuses on this DLCI.
Status: mandatory Access: read-only
OBJECT-TYPE    
  Counter  

sfrapPerfLmiPerDlciRxFullEnqByteCnt 1.3.6.1.4.1.485.7.5.4.17.1.9
The number of bytes received in Full Status enquiries on this DLCI.
Status: mandatory Access: read-only
OBJECT-TYPE    
  Counter  

sfrapPerfLmiPerDlciTxFullEnqByteCnt 1.3.6.1.4.1.485.7.5.4.17.1.10
The number of bytes transmitted in Full Status enquiries on this DLCI.
Status: mandatory Access: read-only
OBJECT-TYPE    
  Counter  

sfrapPerfLmiPerDlciRxFullStatByteCnt 1.3.6.1.4.1.485.7.5.4.17.1.11
The number of bytes received in Full Status messages on this DLCI.
Status: mandatory Access: read-only
OBJECT-TYPE    
  Counter  

sfrapPerfLmiPerDlciTxFullStatByteCnt 1.3.6.1.4.1.485.7.5.4.17.1.12
The number of bytes transmitted in Full Status messages on this DLCI.
Status: mandatory Access: read-only
OBJECT-TYPE    
  Counter  

sfrapPerfLmiPerDlciRxOtherByteCnt 1.3.6.1.4.1.485.7.5.4.17.1.13
The number of received bytes on this DLCI from LMI protocols that are not counted elsewhere (other than Total) in this table.
Status: mandatory Access: read-only
OBJECT-TYPE    
  Counter  

sfrapPerfLmiPerDlciTxOtherByteCnt 1.3.6.1.4.1.485.7.5.4.17.1.14
The number of transmitted bytes on this DLCI from LMI protocols that are not counted elsewhere (other than Total) in this table.
Status: mandatory Access: read-only
OBJECT-TYPE    
  Counter  

sfrapPerfLmiTotalTable 1.3.6.1.4.1.485.7.5.4.18
Short Term Statistics on LMI protocol across all DLCIs.
Status: mandatory Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    SfrapPerfLmiTotalEntry

sfrapPerfLmiTotalEntry 1.3.6.1.4.1.485.7.5.4.18.1
The LMI Short Term Statistics across all DLCIs.
Status: mandatory Access: not-accessible
OBJECT-TYPE    
  SfrapPerfLmiTotalEntry  

sfrapPerfLmiTotalInterval 1.3.6.1.4.1.485.7.5.4.18.1.1
The Short Term statistics model maintains three intervals: current, previous, and cumulative totals. Interval duration is defined by the Short Term Timer (CfgFrPerfTimersSTInterval). (1) Currently active short term interval (2) Previously completed short term interval (3) Cumulative total since last cleared.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER current-interval(1), previous-interval(2), cumulative-counts(3)  

sfrapPerfLmiTotalDlciValue 1.3.6.1.4.1.485.7.5.4.18.1.2
OBSOLETE.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER  

sfrapPerfLmiTotalRxTotalByteCnt 1.3.6.1.4.1.485.7.5.4.18.1.3
The total number of received LMI bytes counted across all DLCIs.
Status: mandatory Access: read-only
OBJECT-TYPE    
  Counter  

sfrapPerfLmiTotalTxTotalByteCnt 1.3.6.1.4.1.485.7.5.4.18.1.4
The total number of transmitted LMI bytes counted across all DLCIs.
Status: mandatory Access: read-only
OBJECT-TYPE    
  Counter  

sfrapPerfLmiTotalRxLivoEnqByteCnt 1.3.6.1.4.1.485.7.5.4.18.1.5
The number of bytes received in Link Integrity Verification Only (LIVO) enquiries across all DLCIs.
Status: mandatory Access: read-only
OBJECT-TYPE    
  Counter  

sfrapPerfLmiTotalTxLivoEnqByteCnt 1.3.6.1.4.1.485.7.5.4.18.1.6
The number of bytes transmitted in Link Integrity Verification Only (LIVO) enquiries across all DLCIs.
Status: mandatory Access: read-only
OBJECT-TYPE    
  Counter  

sfrapPerfLmiTotalRxLivoStatByteCnt 1.3.6.1.4.1.485.7.5.4.18.1.7
The number of bytes received in Link Integrity Verification Only (LIVO) enquiries across all DLCIs.
Status: mandatory Access: read-only
OBJECT-TYPE    
  Counter  

sfrapPerfLmiTotalTxLivoStatByteCnt 1.3.6.1.4.1.485.7.5.4.18.1.8
The number of bytes transmitted in Link Integrity Verification Only (LIVO) enquiries across all DLCIs.
Status: mandatory Access: read-only
OBJECT-TYPE    
  Counter  

sfrapPerfLmiTotalRxFullEnqByteCnt 1.3.6.1.4.1.485.7.5.4.18.1.9
The number of bytes received in Full Status enquiries across all DLCIs.
Status: mandatory Access: read-only
OBJECT-TYPE    
  Counter  

sfrapPerfLmiTotalTxFullEnqByteCnt 1.3.6.1.4.1.485.7.5.4.18.1.10
The number of bytes transmitted in Full Status enquiries across all DLCIs.
Status: mandatory Access: read-only
OBJECT-TYPE    
  Counter  

sfrapPerfLmiTotalRxFullStatByteCnt 1.3.6.1.4.1.485.7.5.4.18.1.11
The number of bytes received in Full Status messages across all DLCIs.
Status: mandatory Access: read-only
OBJECT-TYPE    
  Counter  

sfrapPerfLmiTotalTxFullStatByteCnt 1.3.6.1.4.1.485.7.5.4.18.1.12
The number of bytes transmitted in Full Status messages across all DLCIs.
Status: mandatory Access: read-only
OBJECT-TYPE    
  Counter  

sfrapPerfLmiTotalRxOtherByteCnt 1.3.6.1.4.1.485.7.5.4.18.1.13
The number of received bytes across all DLCIs from LMI protocols that are not counted elsewhere (other than Total) in this table.
Status: mandatory Access: read-only
OBJECT-TYPE    
  Counter  

sfrapPerfLmiTotalTxOtherByteCnt 1.3.6.1.4.1.485.7.5.4.18.1.14
The number of transmitted bytes across all DLCIs from LMI protocols that are not counted elsewhere (other than Total) in this table.
Status: mandatory Access: read-only
OBJECT-TYPE    
  Counter  

sfrapPerfNetworkLongTerm 1.3.6.1.4.1.485.7.5.5
OBJECT IDENTIFIER    

sfrapPerfNetwLongTermTable 1.3.6.1.4.1.485.7.5.5.1
Long Term Statistics by DLCI, protocol, and interval. LT statistics are collected on a configurable set of DLCIs and protocols. There are 96 intervals maintained each with a duration defined by the Long Term Timer. Interval 96 is the current window and Interval 1 is furthest back in time (96xLT Timer seconds ago).
Status: mandatory Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    SfrapPerfNetwLongTermEntry

sfrapPerfNetwLongTermEntry 1.3.6.1.4.1.485.7.5.5.1.1
The Long Term Statistic for a particular DLCI, protocol and interval.
Status: mandatory Access: not-accessible
OBJECT-TYPE    
  SfrapPerfNetwLongTermEntry  

sfrapPerfNetwLongTermDlci 1.3.6.1.4.1.485.7.5.5.1.1.1
The DLCI monitored for the statistics. The Long Term DLCI filter must first be configured (CfgFrPerfLTDlciFilterEntry).
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER  

sfrapPerfNetwLongTermProtocol 1.3.6.1.4.1.485.7.5.5.1.1.2
The type of protocol monitored for the statistics.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER ip-tx-bc(1), ip-rx-bc(2), tcp-ip-tx-bc(3), tcp-ip-rx-bc(4), ftp-tcp-ip-tx-bc(5), ftp-tcp-ip-rx-bc(6), telnet-tcp-ip-tx-bc(7), telnet-tcp-ip-rx-bc(8), smtp-tcp-ip-tx-bc(9), smtp-tcp-ip-rx-bc(10), http-tcp-ip-tx-bc(13), http-tcp-ip-rx-bc(14), netbios-ssn-tcp-ip-tx-bc(15), netbios-ssn-tcp-ip-rx-bc(16), udp-ip-tx-bc(21), udp-ip-rx-bc(22), tftp-udp-ip-tx-bc(29), tftp-udp-ip-rx-bc(30), netbios-dgm-udp-ip-tx-bc(33), netbios-dgm-udp-ip-rx-bc(34), snmp-udp-ip-tx-bc(35), snmp-udp-ip-rx-bc(36), snmptrap-udp-ip-tx-bc(37), snmptrap-udp-ip-rx-bc(38), rip-udp-ip-tx-bc(39), rip-udp-ip-rx-bc(40), icmp-ip-tx-bc(41), icmp-ip-rx-bc(42), echorep-icmp-ip-tx-bc(43), echorep-icmp-ip-rx-bc(44), dest-unr-icmp-ip-tx-bc(45), dest-unr-icmp-ip-rx-bc(46), src-quench-icmp-ip-tx-bc(47), src-quench-icmp-ip-rx-bc(48), redirect-icmp-ip-tx-bc(49), redirect-icmp-ip-rx-bc(50), echoreq-icmp-ip-tx-bc(51), echoreq-icmp-ip-rx-bc(52), time-excd-icmp-ip-tx-bc(53), time-excd-icmp-ip-rx-bc(54), param-prob-icmp-ip-tx-bc(55), param-prob-icmp-ip-rx-bc(56), timestamp-req-icmp-ip-tx-bc(57), timestamp-req-icmp-ip-rx-bc(58), timestamp-rep-icmp-ip-tx-bc(59), timestamp-rep-icmp-ip-rx-bc(60), addr-mask-req-icmp-ip-tx-bc(61), addr-mask-req-icmp-ip-rx-bc(62), addr-mask-rep-icmp-ip-tx-bc(63), addr-mask-rep-icmp-ip-rx-bc(64), pkt-too-big-icmp-ip-tx-bc(65), pkt-too-big-icmp-ip-rx-bc(66), gp-mem-query-icmp-ip-tx-bc(67), gp-mem-query-icmp-ip-rx-bc(68), gp-mem-report-icmp-ip-tx-bc(69), gp-mem-report-icmp-ip-rx-bc(70), gp-mem-reduct-icmp-ip-tx-bc(71), gp-mem-reduct-icmp-ip-rx-bc(72), ospf-ip-tx-bc(73), ospf-ip-rx-bc(74), other-ip-tx-bc(75), other-ip-rx-bc(76), ipx-tx-bc(77), ipx-rx-bc(78), spx-ipx-tx-bc(79), spx-ipx-rx-bc(80), ncp-ipx-tx-bc(81), ncp-ipx-rx-bc(82), sap-ipx-tx-bc(83), sap-ipx-rx-bc(84), rip-ipx-tx-bc(85), rip-ipx-rx-bc(86), netbios-ipx-tx-bc(87), netbios-ipx-rx-bc(88), other-ipx-tx-bc(89), other-ipx-rx-bc(90), arp-tx-bc(91), arp-rx-bc(92), arp-req-tx-bc(93), arp-req-rx-bc(94), arp-rep-tx-bc(95), arp-rep-rx-bc(96), rarp-req-tx-bc(97), rarp-req-rx-bc(98), rarp-rep-tx-bc(99), rarp-rep-rx-bc(100), inarp-req-tx-bc(101), inarp-req-rx-bc(102), inarp-rep-tx-bc(103), inarp-rep-rx-bc(104), sna-tx-bc(105), sna-rx-bc(106), sna-subarea-tx-bc(107), sna-subarea-rx-bc(108), sna-periph-tx-bc(109), sna-periph-rx-bc(110), sna-appn-tx-bc(111), sna-appn-rx-bc(112), sna-netbios-tx-bc(113), sna-netbios-rx-bc(114), cisco-tx-bc(115), cisco-rx-bc(116), other-tx-bc(117), other-rx-bc(118), user-defined-1-tx-bc(119), user-defined-1-rx-bc(120), user-defined-2-tx-bc(121), user-defined-2-rx-bc(122), user-defined-3-tx-bc(123), user-defined-3-rx-bc(124), user-defined-4-tx-bc(125), user-defined-4-rx-bc(126), thru-byte-tx-bc(127), thru-byte-rx-bc(128), thru-frame-tx-c(129), thru-frame-rx-c(130), thru-fecn-tx-c(131), thru-fecn-rx-c(132), thru-becn-tx-c(133), thru-becn-rx-c(134), thru-de-tx-c(135), thru-de-rx-c(136), cir-percent-range1-tx-bc(137), cir-percent-range1-rx-bc(138), cir-percent-range2-tx-bc(139), cir-percent-range2-rx-bc(140), cir-percent-range3-tx-bc(141), cir-percent-range3-rx-bc(142), cir-percent-range4-tx-bc(143), cir-percent-range4-rx-bc(144), cir-percent-range5-tx-bc(145), cir-percent-range5-rx-bc(146), cir-percent-range6-tx-bc(147), cir-percent-range6-rx-bc(148), cir-percent-range7-tx-bc(149), cir-percent-range7-rx-bc(150), cir-percent-range8-tx-bc(151), cir-percent-range8-rx-bc(152), lmi-tx-bc(153), lmi-rx-bc(154), lmi-livo-enq-tx-bc(155), lmi-livo-enq-rx-bc(156), lmi-livo-stat-tx-bc(157), lmi-livo-stat-rx-bc(158), lmi-full-enq-tx-bc(159), lmi-full-enq-rx-bc(160), lmi-full-stat-tx-bc(161), lmi-full-stat-rx-bc(162), lmi-other-tx-bc(163), lmi-other-rx-bc(164), total-uptime(165), total-downtime(166), igrp-tx-bc(167), igrp-rx-bc(168), vnip-tx-bc(169), vnip-rx-bc(170), annex-g-tx-bc(171), annex-g-rx-bc(172)  

sfrapPerfNetwLongTermInterval 1.3.6.1.4.1.485.7.5.5.1.1.3
The time interval in which the value was collected. Long Term statistis are maintained for 96 intervals with the interval duration defined by (CfgFrPerfTimersLTInterval).
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER  

sfrapPerfNetwLongTermValue 1.3.6.1.4.1.485.7.5.5.1.1.4
The statistic collected for the given DLCI and protocol and within the given time interval.
Status: mandatory Access: read-only
OBJECT-TYPE    
  Counter  

sfrapPerfNetwLongTermAltTable 1.3.6.1.4.1.485.7.5.5.2
This is an alternative method to access the database of long term statistics. The statistics are indexed by DLCI and protocol and are returned in an OCTETSTRING.
Status: mandatory Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    SfrapPerfNetwLongTermAltEntry

sfrapPerfNetwLongTermAltEntry 1.3.6.1.4.1.485.7.5.5.2.1
The Long Term Statistic for a particular DLCI and protocol.
Status: mandatory Access: not-accessible
OBJECT-TYPE    
  SfrapPerfNetwLongTermAltEntry  

sfrapPerfNetwLongTermAltDlci 1.3.6.1.4.1.485.7.5.5.2.1.1
The DLCI monitored for the statistics.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER  

sfrapPerfNetwLongTermAltProtocol 1.3.6.1.4.1.485.7.5.5.2.1.2
The protocol monitored for the statistics.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER ip-tx-bc(1), ip-rx-bc(2), tcp-ip-tx-bc(3), tcp-ip-rx-bc(4), ftp-tcp-ip-tx-bc(5), ftp-tcp-ip-rx-bc(6), telnet-tcp-ip-tx-bc(7), telnet-tcp-ip-rx-bc(8), smtp-tcp-ip-tx-bc(9), smtp-tcp-ip-rx-bc(10), http-tcp-ip-tx-bc(13), http-tcp-ip-rx-bc(14), netbios-ssn-tcp-ip-tx-bc(15), netbios-ssn-tcp-ip-rx-bc(16), udp-ip-tx-bc(21), udp-ip-rx-bc(22), tftp-udp-ip-tx-bc(29), tftp-udp-ip-rx-bc(30), netbios-dgm-udp-ip-tx-bc(33), netbios-dgm-udp-ip-rx-bc(34), snmp-udp-ip-tx-bc(35), snmp-udp-ip-rx-bc(36), snmptrap-udp-ip-tx-bc(37), snmptrap-udp-ip-rx-bc(38), rip-udp-ip-tx-bc(39), rip-udp-ip-rx-bc(40), icmp-ip-tx-bc(41), icmp-ip-rx-bc(42), echorep-icmp-ip-tx-bc(43), echorep-icmp-ip-rx-bc(44), dest-unr-icmp-ip-tx-bc(45), dest-unr-icmp-ip-rx-bc(46), src-quench-icmp-ip-tx-bc(47), src-quench-icmp-ip-rx-bc(48), redirect-icmp-ip-tx-bc(49), redirect-icmp-ip-rx-bc(50), echoreq-icmp-ip-tx-bc(51), echoreq-icmp-ip-rx-bc(52), time-excd-icmp-ip-tx-bc(53), time-excd-icmp-ip-rx-bc(54), param-prob-icmp-ip-tx-bc(55), param-prob-icmp-ip-rx-bc(56), timestamp-req-icmp-ip-tx-bc(57), timestamp-req-icmp-ip-rx-bc(58), timestamp-rep-icmp-ip-tx-bc(59), timestamp-rep-icmp-ip-rx-bc(60), addr-mask-req-icmp-ip-tx-bc(61), addr-mask-req-icmp-ip-rx-bc(62), addr-mask-rep-icmp-ip-tx-bc(63), addr-mask-rep-icmp-ip-rx-bc(64), pkt-too-big-icmp-ip-tx-bc(65), pkt-too-big-icmp-ip-rx-bc(66), gp-mem-query-icmp-ip-tx-bc(67), gp-mem-query-icmp-ip-rx-bc(68), gp-mem-report-icmp-ip-tx-bc(69), gp-mem-report-icmp-ip-rx-bc(70), gp-mem-reduct-icmp-ip-tx-bc(71), gp-mem-reduct-icmp-ip-rx-bc(72), ospf-ip-tx-bc(73), ospf-ip-rx-bc(74), other-ip-tx-bc(75), other-ip-rx-bc(76), ipx-tx-bc(77), ipx-rx-bc(78), spx-ipx-tx-bc(79), spx-ipx-rx-bc(80), ncp-ipx-tx-bc(81), ncp-ipx-rx-bc(82), sap-ipx-tx-bc(83), sap-ipx-rx-bc(84), rip-ipx-tx-bc(85), rip-ipx-rx-bc(86), netbios-ipx-tx-bc(87), netbios-ipx-rx-bc(88), other-ipx-tx-bc(89), other-ipx-rx-bc(90), arp-tx-bc(91), arp-rx-bc(92), arp-req-tx-bc(93), arp-req-rx-bc(94), arp-rep-tx-bc(95), arp-rep-rx-bc(96), rarp-req-tx-bc(97), rarp-req-rx-bc(98), rarp-rep-tx-bc(99), rarp-rep-rx-bc(100), inarp-req-tx-bc(101), inarp-req-rx-bc(102), inarp-rep-tx-bc(103), inarp-rep-rx-bc(104), sna-tx-bc(105), sna-rx-bc(106), sna-subarea-tx-bc(107), sna-subarea-rx-bc(108), sna-periph-tx-bc(109), sna-periph-rx-bc(110), sna-appn-tx-bc(111), sna-appn-rx-bc(112), sna-netbios-tx-bc(113), sna-netbios-rx-bc(114), cisco-tx-bc(115), cisco-rx-bc(116), other-tx-bc(117), other-rx-bc(118), user-defined-1-tx-bc(119), user-defined-1-rx-bc(120), user-defined-2-tx-bc(121), user-defined-2-rx-bc(122), user-defined-3-tx-bc(123), user-defined-3-rx-bc(124), user-defined-4-tx-bc(125), user-defined-4-rx-bc(126), thru-byte-tx-bc(127), thru-byte-rx-bc(128), thru-frame-tx-c(129), thru-frame-rx-c(130), thru-fecn-tx-c(131), thru-fecn-rx-c(132), thru-becn-tx-c(133), thru-becn-rx-c(134), thru-de-tx-c(135), thru-de-rx-c(136), cir-percent-range1-tx-bc(137), cir-percent-range1-rx-bc(138), cir-percent-range2-tx-bc(139), cir-percent-range2-rx-bc(140), cir-percent-range3-tx-bc(141), cir-percent-range3-rx-bc(142), cir-percent-range4-tx-bc(143), cir-percent-range4-rx-bc(144), cir-percent-range5-tx-bc(145), cir-percent-range5-rx-bc(146), cir-percent-range6-tx-bc(147), cir-percent-range6-rx-bc(148), cir-percent-range7-tx-bc(149), cir-percent-range7-rx-bc(150), cir-percent-range8-tx-bc(151), cir-percent-range8-rx-bc(152), lmi-tx-bc(153), lmi-rx-bc(154), lmi-livo-enq-tx-bc(155), lmi-livo-enq-rx-bc(156), lmi-livo-stat-tx-bc(157), lmi-livo-stat-rx-bc(158), lmi-full-enq-tx-bc(159), lmi-full-enq-rx-bc(160), lmi-full-stat-tx-bc(161), lmi-full-stat-rx-bc(162), lmi-other-tx-bc(163), lmi-other-rx-bc(164), total-uptime(165), total-downtime(166), igrp-tx-bc(167), igrp-rx-bc(168), vnip-tx-bc(169), vnip-rx-bc(170), annex-g-tx-bc(171), annex-g-rx-bc(172)  

sfrapPerfNetwLongTermAltArray 1.3.6.1.4.1.485.7.5.5.2.1.3
The statistic collected for the given DLCI and protocol.
Status: mandatory Access: read-only
OBJECT-TYPE    
  OCTET STRING  

sfrapPerfNetworkLongTermCommands 1.3.6.1.4.1.485.7.5.5.3
OBJECT IDENTIFIER    

sfrapPerfNetworkLongTermCmdClear 1.3.6.1.4.1.485.7.5.5.3.1
Allows the user to zero out all the statistics in the long term statistics tables. (1) Clear all Long Term statistics
Status: mandatory Access: write-only
OBJECT-TYPE    
  INTEGER clear-statistics(1)  

sfrapPerfCirPercentUtilization 1.3.6.1.4.1.485.7.5.6
OBJECT IDENTIFIER    

sfrapPerfCirPercentUtilizationTable 1.3.6.1.4.1.485.7.5.6.1
Short Term Statistics on the percentage of CIR used on each DLCI. Each short term statistics interval, the count of bytes transmitted and received is used to calculate the percentage of CIR used. The byte count is then added to the appropriate bucket for the CIR percentage range.
Status: mandatory Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    SfrapPerfCirPercentUtilizationEntry

sfrapPerfCirPercentUtilizationEntry 1.3.6.1.4.1.485.7.5.6.1.1
The CIR Percentage Statistics for a particular DLCI. These calculations are done at the completion of each Short Term interval.
Status: mandatory Access: not-accessible
OBJECT-TYPE    
  SfrapPerfCirPercentUtilizationEntry  

sfrapPerfCirPercentUtilizationInterval 1.3.6.1.4.1.485.7.5.6.1.1.1
The Short Term statistics model maintains three intervals: current, previous, and cumulative totals. Interval duration is defined by the Short Term Timer (CfgFrPerfTimersSTInterval). (1) Currently active short term interval (2) Previously completed short term interval (3) Cumulative total since last cleared.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER current-interval(1), previous-interval(2), cumulative-counts(3)  

sfrapPerfCirPercentUtilizationDlciValue 1.3.6.1.4.1.485.7.5.6.1.1.2
The DLCI value with which the Statistics are associated.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER  

sfrapPerfCirRxPercentUtilizationRange1 1.3.6.1.4.1.485.7.5.6.1.1.21
The number of short-term intervals during which rx data throughput on this DLCI compared to CIR was in range 1 (0% of CIR).
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER  

sfrapPerfCirRxPercentUtilizationRange2 1.3.6.1.4.1.485.7.5.6.1.1.22
The number of short-term intervals during which rx data throughput on this DLCI compared to CIR was in range 2 (1-10% of CIR).
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER  

sfrapPerfCirRxPercentUtilizationRange3 1.3.6.1.4.1.485.7.5.6.1.1.23
The number of short-term intervals during which rx data throughput on this DLCI compared to CIR was in range 3 (11-20% of CIR).
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER  

sfrapPerfCirRxPercentUtilizationRange4 1.3.6.1.4.1.485.7.5.6.1.1.24
The number of short-term intervals during which rx data throughput on this DLCI compared to CIR was in range 4 (21-50% of CIR).
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER  

sfrapPerfCirRxPercentUtilizationRange5 1.3.6.1.4.1.485.7.5.6.1.1.25
The number of short-term intervals during which rx data throughput on this DLCI compared to CIR was in range 5 (51-80% of CIR).
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER  

sfrapPerfCirRxPercentUtilizationRange6 1.3.6.1.4.1.485.7.5.6.1.1.26
The number of short-term intervals during which rx data throughput on this DLCI compared to CIR was in range 6 (81-100% of CIR).
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER  

sfrapPerfCirRxPercentUtilizationRange7 1.3.6.1.4.1.485.7.5.6.1.1.27
The number of short-term intervals during which rx data throughput on this DLCI compared to CIR was in range 7 (101-150% of CIR).
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER  

sfrapPerfCirRxPercentUtilizationRange8 1.3.6.1.4.1.485.7.5.6.1.1.28
The number of short-term intervals during which rx data throughput on this DLCI compared to CIR was in range 8 (> 150% of CIR).
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER  

sfrapPerfCirTxPercentUtilizationRange1 1.3.6.1.4.1.485.7.5.6.1.1.41
The number of short-term intervals during which tx data throughput on this DLCI compared to CIR was in range 1 (0% of CIR).
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER  

sfrapPerfCirTxPercentUtilizationRange2 1.3.6.1.4.1.485.7.5.6.1.1.42
The number of short-term intervals during which tx data throughput on this DLCI compared to CIR was in range 2 (1-10% of CIR).
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER  

sfrapPerfCirTxPercentUtilizationRange3 1.3.6.1.4.1.485.7.5.6.1.1.43
The number of short-term intervals during which tx data throughput on this DLCI compared to CIR was in range 3 (11-20% of CIR).
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER  

sfrapPerfCirTxPercentUtilizationRange4 1.3.6.1.4.1.485.7.5.6.1.1.44
The number of short-term intervals during which tx data throughput on this DLCI compared to CIR was in range 4 (21-50% of CIR).
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER  

sfrapPerfCirTxPercentUtilizationRange5 1.3.6.1.4.1.485.7.5.6.1.1.45
The number of short-term intervals during which tx data throughput on this DLCI compared to CIR was in range 5 (51-80% of CIR).
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER  

sfrapPerfCirTxPercentUtilizationRange6 1.3.6.1.4.1.485.7.5.6.1.1.46
The number of short-term intervals during which tx data throughput on this DLCI compared to CIR was in range 6 (81-100% o0f CIR).
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER  

sfrapPerfCirTxPercentUtilizationRange7 1.3.6.1.4.1.485.7.5.6.1.1.47
The number of short-term intervals during which tx data throughput on this DLCI compared to CIR was in range 7 (101-150% of CIR).
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER  

sfrapPerfCirTxPercentUtilizationRange8 1.3.6.1.4.1.485.7.5.6.1.1.48
The number of short-term intervals during which tx data throughput on this DLCI compared to CIR was in range 8 (> 150% of CIR).
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER  

sfrapPerfCurrentPerDlciUtilizationTable 1.3.6.1.4.1.485.7.5.6.2
The current measurement of utilization as a percentage of CIR on each DLCI. Each short term statistics interval, the count of bytes transmitted and received is used to calculate the percentage of CIR used.
Status: mandatory Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    SfrapPerfCurrentPerDlciUtilizationEntry

sfrapPerfCurrentPerDlciUtilizationEntry 1.3.6.1.4.1.485.7.5.6.2.1
The utilization statistics for a particular DLCI.
Status: mandatory Access: not-accessible
OBJECT-TYPE    
  SfrapPerfCurrentPerDlciUtilizationEntry  

sfrapPerfCurrentPerDlciUtilizationDlciValue 1.3.6.1.4.1.485.7.5.6.2.1.1
The DLCI value with which the Statistics are associated.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER  

sfrapPerfCurrentPerDlciRxUtilization 1.3.6.1.4.1.485.7.5.6.2.1.2
The receive direction utilization as a percentage of CIR.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER  

sfrapPerfCurrentPerDlciTxUtilization 1.3.6.1.4.1.485.7.5.6.2.1.3
The transmit direction utilization as a percentage of CIR.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER  

sfrapPerfCurrentPerDlciAggregateUtilization 1.3.6.1.4.1.485.7.5.6.2.1.4
The aggregate utilization, the average of the receive and transmit utilization as a percentage of CIR.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER  

sfrapPerfCurrentUnitUtilization 1.3.6.1.4.1.485.7.5.6.3
OBJECT IDENTIFIER    

sfrapPerfCurrentDteUtilization 1.3.6.1.4.1.485.7.5.6.3.2
The DTE interface utilization as a percentage of line rate.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER  

sfrapPerfCurrentWanUtilization 1.3.6.1.4.1.485.7.5.6.3.3
The WAN interface utilization as a percentage of line rate.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER  

sfrapPerfCurrentAggregateUtilization 1.3.6.1.4.1.485.7.5.6.3.4
The aggregate utilization of the unit, the average of the DTE and WAN interface utilizations as a percentage of line rate.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER  

sfrapPerfFRStatsCollectionStatus 1.3.6.1.4.1.485.7.5.7
OBJECT IDENTIFIER    

sfrapPerfFRStatsCollection 1.3.6.1.4.1.485.7.5.7.1
Tells the GUI whether or not the Frame Relay Performance statistics are valid or not. This is a SFRAP Low Speed option, if the user's network bandwidth has exceeded the Low Speed boundary, then it is set to not-collecting-stats (1) all other cases it is set to collecting-stats (2).
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER not-collecting-stats(1), collecting-stats(2)  

sfrapEventTrapLog 1.3.6.1.4.1.485.7.10
OBJECT IDENTIFIER    

sfrapEventTrapLogTable 1.3.6.1.4.1.485.7.10.1
This table contains the Event/Trap log. The entries are indexed by sequence number.
Status: mandatory Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    SFRAPEventTrapLogEntry

sfrapEventTrapLogEntry 1.3.6.1.4.1.485.7.10.1.1
The event record for a particular event.
Status: mandatory Access: not-accessible
OBJECT-TYPE    
  SFRAPEventTrapLogEntry  

sfrapEventTrapLogSeqNum 1.3.6.1.4.1.485.7.10.1.1.1
The sequence number associated with an event record.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER  

sfrapEventTrapLogGenericEvent 1.3.6.1.4.1.485.7.10.1.1.2
The SNMP generic trap or event number.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER  

sfrapEventTrapLogSpecificEvent 1.3.6.1.4.1.485.7.10.1.1.3
The SNMP specific trap or event sub-identifier number.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER  

sfrapEventTrapLogTimeStamp 1.3.6.1.4.1.485.7.10.1.1.4
The SNMP trap timestamp.
Status: mandatory Access: read-only
OBJECT-TYPE    
  TimeTicks  

sfrapEventTrapLogVarBind1 1.3.6.1.4.1.485.7.10.1.1.5
Variable Binding 1 for this SNMP Trap event.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER  

sfrapEventTrapLogVarBind2 1.3.6.1.4.1.485.7.10.1.1.6
Variable Binding 2 for this SNMP Trap event.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER  

sfrapEventTrapLogVarBind3 1.3.6.1.4.1.485.7.10.1.1.7
Variable Binding 3 for this SNMP Trap event.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER  

sfrapEventLogAltTable 1.3.6.1.4.1.485.7.10.2
This is an alternative method to access the database of the Event/Trap Log. The database is indexed by Sequence Number and Event/Trap log's are returned in an OCTETSTRING.
Status: mandatory Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    SFRAPEventLogAltEntry

sfrapEventLogAltEntry 1.3.6.1.4.1.485.7.10.2.1
The Event/Trap Log for a particular sequence number.
Status: mandatory Access: not-accessible
OBJECT-TYPE    
  SFRAPEventLogAltEntry  

sfrapEventLogAltSeqNum 1.3.6.1.4.1.485.7.10.2.1.1
The Sequence Number monitored for the Event Log
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER  

sfrapEventLogAltArray 1.3.6.1.4.1.485.7.10.2.1.2
The Event / Trap log for the given sequence number.
Status: mandatory Access: read-only
OBJECT-TYPE    
  OCTET STRING  

sfrapEventLogCurrentSeqNum 1.3.6.1.4.1.485.7.10.3
The current index into the Event Log Table.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER  

sfrapEventLogFreeze 1.3.6.1.4.1.485.7.10.4
This freezes the Event/Trap Log. freeze(1) will prevent Events / Traps from being entered into the database, un-freeze(2) will allow Events / Traps to be logged into the database. An event will be logged indicating a set of this entry
Status: mandatory Access: write-only
OBJECT-TYPE    
  INTEGER freeze(1), un-freeze(2)  

sfrapEventLogClear 1.3.6.1.4.1.485.7.10.5
This clears the Event/Trap Log.
Status: mandatory Access: write-only
OBJECT-TYPE    
  INTEGER clear(1)  

sfrapAlarmType 1.3.6.1.4.1.485.7.6
The alarm type of the most recent TRAP generated.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER bad-config-in-set(1), config-local-update(2), local-unit-loopback-enabled(14), local-unit-loopback-disabled(15), local-unit-loopback-failure(16), local-dte-loopback-enabled(17), local-dte-loopback-disabled(18), local-dte-loopback-failure(19), dlci-active(47), dlci-inactive(48), dlci-td-threshold(49), lmi-sourcing-change-passthru(50), lmi-sourcing-change-user-dte(51), lmi-sourcing-change-net-dte(52), lmi-sourcing-change-user-net(53), lmi-sourcing-change-net-net(54), dte-signal-rts-on(55), dte-signal-rts-off(56), dte-signal-dtr-on(57), dte-signal-dtr-off(58), lmi-non-incr-seq-num-dte(59), lmi-non-incr-seq-num-net(60), lmi-seq-num-mismatch-dte(61), lmi-seq-num-mismatch-net(62), trap-muting-active(75), trap-muting-inactive(76), low-speed-exceeded(80), low-speed-resumed(81), op-mode-cutthru-enabled(82), op-mode-cutthru-disabled(83), local-dte2-loopback-enabled(84), local-dte2-loopback-disabled(85), local-dte2-loopback-failure(86), vloop-loop-up(90), vloop-loop-down(91), vloop-up-via-remote(92), vloop-down-via-remote(93), vloop-failed(94), vbert-started(95), vbert-stopped(96), vbert-request-failed(97), dte-signal-control-on(100), dte-signal-control-off(101), dte-signal-indicate-on(102), dte-signal-indicate-off(103), pvc-rx-utilization-exceeded(138), pvc-tx-utilization-exceeded(139), pvc-rx-utilization-cleared(140), pvc-tx-utilization-cleared(141), config-install-success(142), tftp-requested(257), tftp-transferring(258), tftp-programming(259), tftp-aborted(260), tftp-success(261), tftp-host-unreachable(262), tftp-no-file(263), tftp-invalid-file(264), tftp-corrupt-file(265)  

sfrapDLCINum 1.3.6.1.4.1.485.7.7
The DLCI number for the most recent DLCI TRAP generated.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER  

sfrapInterface 1.3.6.1.4.1.485.7.8
The interface most recently reported in a TRAP.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER to-dte(1), to-dce(2)  

sfrapIpAddress 1.3.6.1.4.1.485.7.9
The IP address most recently reported in a TRAP.
Status: mandatory Access: read-only
OBJECT-TYPE    
  IpAddress  

sfrapPercentUtilization 1.3.6.1.4.1.485.7.11
The percent utilization for a DLCI most recently reported in a TRAP.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER  

sfrapUtilizationThreshold 1.3.6.1.4.1.485.7.12
The percent utilization threshold for a DLCI most recently reported in a TRAP.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER  

sfrapCfgLockIpAddress 1.3.6.1.4.1.485.7.13
The IP address of the management station locking the configuration most recently reported in a TRAP.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER  

sfrapTrap 0
A sfrapTrap trap signifies that the sending node had its `sfrapAlarmType` variable modified.
TRAP-TYPE    

sfrapBadConfigTrap 1
Unit has received a configuration update request through SNMP but the request was rejected due to an incorrect or inappropriate parameter.
TRAP-TYPE    

sfrapLocalConfigTrap 2
Unit configuration has been updated locally (console port or front panel keypad) or remotely (telnet).
TRAP-TYPE    

sfrapLocalUnitLoopbackEnabledTrap 14
Unit is in a bidirectional unit loopback. Data is received from either interface, processed, and transmitted back towards the same interface. When configured for Frame Relay operation the unit will preserve the LMI path during this loopback. In Frame Relay mode, only valid frames are looped back (pseudorandom test patterns will be dropped).
TRAP-TYPE    

sfrapLocalUnitLoopbackDisabledTrap 15
Bidirectional unit loopback path is removed.
TRAP-TYPE    

sfrapLocalUnitLoopbackFailedTrap 16
Bidirectional unit loopback request has been rejected by the unit. Typically, this is due to the presence of another loopback condition.
TRAP-TYPE    

sfrapLocalToDteLoopbackEnabledTrap 17
Unit is in a bidirectional TO-DTE loopback. All data received at the TO-DTE interface is looped back regardless of format or content (line loopback). When configured for Frame Relay operation the unit will not preserve the LMI path during this loopback. Data received from the TO-DCE is processed and transmitted back out the TO-DCE. In Frame Relay mode, on the TO-DCE interface, only valid frames are looped back (pseudorandom test patterns will be dropped).
TRAP-TYPE    

sfrapLocalToDteLoopbackDisabledTrap 18
Bidirectional TO-DTE loopback path is removed.
TRAP-TYPE    

sfrapLocalToDteLoopbackFailedTrap 19
Bidirectional TO-DTE loopback request has been rejected by the unit. Typically, this is due to the presence of another loopback condition.
TRAP-TYPE    

sfrapDLCIActiveTrap 47
Unit is reporting this DLCI as active and provisioned. An active DLCI is one that is explictly declared ACTIVE in an LMI Full Status Response (typically coming from a frame relay switch).
TRAP-TYPE    

sfrapDLCIInactiveTrap 48
Unit is reporting this DLCI as inactive. An inactive DLCI is determined inactive one of two ways: it is either explictly declared inactive in an LMI Full Status Response (typically coming from a frame relay switch) or a Full Status Response is not seen causing a Full Status Timer expiry. Having the unit's full status timer too low could result in the unit falsely declaring DLCIs inactive (then active again). This does not interfere with any data activity on the DLCI but could result in excessive traps.
TRAP-TYPE    

sfrapDLCITDThresholdTrap 49
VNIP has measured a round-trip transit delay on this PVC to this peer which exceeds the user-defined threshold.
TRAP-TYPE    

sfrapLmiSourcingChangePassthruTrap 50
Unit is not sourcing any LMI messages. If this state persists then LMI is up and the proper handshaking is occurring independent of the unit. This may also be a transient state if the unit is in an LMI hunt mode. If this trap occurs repeatedly, separated by other LMI sourcing states, the unit is not seeing any of the expected LMI messages from either interface. Check LMI type, connectivity, and configuration of associated equipment.
TRAP-TYPE    

sfrapLmiSourcingChangeUserToDteTrap 51
Unit is acting as a source of LMI Status Requests (Link Integrity Verification, Keep Alive). If this state persists then the equipment attached to the TO-DTE interface is configured as a Frame Relay DCE but a companion Frame Relay DTE device is not seen out the TO-DCE. This could also be a transient state if the unit is in an LMI hunt mode. If this trap occurs repeatedly, separated by other LMI sourcing states, the unit is not seeing any of the expected LMI messages from either interface. Check LMI type, connectivity, and configuration of associated equipment.
TRAP-TYPE    

sfrapLmiSourcingChangeNetToDteTrap 52
Unit is acting as a source of LMI Status Responses (Link Intergrity Verification, Keep Alive). If this state persists then the equpiment attached to the TO-DTE interface is configured as a Frame Relay DTE but a companion Frame Relay DCE device is not seen out the TO-DCE. This could also be a transient state if the unit is in an LMI hunt mode. If this trap occurs repeatedly, separated by other LMI sourcing states, the unit is not seeing any of the expected LMI messages from either interface. Check LMI type, connectivity, and configuration of external equipment.
TRAP-TYPE    

sfrapLmiSourcingChangeUserToDceTrap 53
Unit is acting as a source of LMI Status Requests (Link Integrity Verification, Keep Alive). If this state persists then the equipment attached to the TO-DCE interface is configured as a Frame Relay DCE but a companion Frame Relay DTE device is not seen out the TO-DTE interface. This could also be a transient state if the unit is in an LMI hunt mode. If this trap occurs repeatedly, separated by other LMI sourcing states, the unit is not seeing any of the expected LMI messages from either interface. Check LMI type, connectivity, and configuration of associated equipment.
TRAP-TYPE    

sfrapLmiSourcingChangeNetToDceTrap 54
Unit is acting as a source of LMI Status Responses (Link Integrity Verification, Keep Alive). If this state persists then the equipment attached to the TO-DCE interface is configured as a Frame Relay DTE but a companion Frame Relay DCE device is not seen out the TO-DTE interface. This could also be a transient state if the unit is in an LMI hunt mode. If this trap occurs repeatedly, separated by other LMI sourcing states, the unit is not seeing any of the expected LMI messages from either interface. Check LMI type, connectivity, and configuration of associated equipment.
TRAP-TYPE    

sfrapDteSignalRtsOnTrap 55
Unit's DTE Request to Send (RTS) interface control signal is now active (on). This signal is presented by the external DTE device. Unit may be configured to ignore the state of this signal or to require it for data transmission.
TRAP-TYPE    

sfrapDteSignalRtsOffTrap 56
Unit's DTE Request to Send (RTS) interface control signal is now inactive (off). This signal is presented by the external DTE device. Unit may be configured to ignore the state of this signal or to require it for data transmission.
TRAP-TYPE    

sfrapDteSignalDtrOnTrap 57
Unit's DTE Data Terminal Ready (DTR) interface control signal is now active (on). This signal is presented by the external DTE device. The unit may be configured to ignore the state of this signal or to require it for data transmission.
TRAP-TYPE    

sfrapDteSignalDtrOffTrap 58
Unit's DTE Data Terminal Ready (DTR) interface control signal is now inactive (off). This signal is presented by the external DTE device. Unit may be configured to ignore the state of this signal or to require it for data transmission.
TRAP-TYPE    

sfrapNonIncrLmiSeqNumToDteTrap 59
Unit has detected a non-incrementing LMI sequence number from the TO-DTE. A Status Enquiry or Status Response message has been seen at the TO-DTE interface. The Link Integrity information element's Send Sequence Number was not incremented or was incremented more than once since the last Send Sequence Number seen from the TO-DTE interface.
TRAP-TYPE    

sfrapNonIncrLmiSeqNumToDceTrap 60
Unit has detected a non-incrementing LMI sequence number from the TO-DCE. A Status Enquiry or Status Response message has been seen at the TO-DCE interface. The Link Integrity information element's Send Sequence Number was not incremented or was incremented more than once since the last Send Sequence Number seen from the TO-DCE interface.
TRAP-TYPE    

sfrapLmiSeqNumMismatchToDteTrap 61
Unit has detetcted an LMI sequence number mismatch from the TO-DTE. A Status Enquiry or Status Response message has been seen at the TO-DTE interface. The Link Inetgrity information element's Receive Sequence Number was not the most recent Send Sequence number sent from the TO-DCE interface.
TRAP-TYPE    

sfrapLmiSeqNumMismatchToDceTrap 62
Unit has detetcted an LMI sequence number mismatch from the TO-DCE. A Status Enquiry or Status Response message has been seen at the TO-DCE interface. The Link Inetgrity information element's Receive Sequence Number was not the most recent Send Sequence number sent from the TO-DTE interface.
TRAP-TYPE    

sfrapTrapMutingActive 75
Trap generation is muted.
TRAP-TYPE    

sfrapTrapMutingInactive 76
Trap generation is re-enabled (muting disabled).
TRAP-TYPE    

sfrapLowSpeedExceededTrap 80
The bandwidth has exceeded the maximum bandwidth for the Low Speed SFRAP. Throttle your network bandwidth.
TRAP-TYPE    

sfrapLowSpeedResumedTrap 81
The bandwidth has is now under the maximum bandwidth for the Low Speed SFRAP. Frame Relay processing will resume.
TRAP-TYPE    

sfrapOpModeCutThruEnabledTrap 82
The Unit has been put into Cut Through mode via the diagnostic. The unit is now operating as if it were in Tap mode. The processor is NOT transmitting data.
TRAP-TYPE    

sfrapOpModeCutThruDisabledTrap 83
The Unit has now resumed normal operation based upon the configured operation mode,Tap or Inband.
TRAP-TYPE    

sfrapLocalDte2LoopbackEnabledTrap 84
Local TO-DCE loopback enabled.
TRAP-TYPE    

sfrapLocalDte2LoopbackDisabledTrap 85
Local TO-DCE loopback disabled.
TRAP-TYPE    

sfrapLocalDte2LoopbackFailedTrap 86
Unable to do a local TO-DCE loopback.
TRAP-TYPE    

sfrapVloopUp 90
A Vnip PVC loopback (VLOOP) request has been sent to a remote device on this DLCI out this interface. The remote unit should respond by looping all data received on this PVC back towards the unit that initiated this request. A PVC running VLOOP will not be running any user data.
TRAP-TYPE    

sfrapVloopDown 91
A Vnip PVC loopback (VLOOP) disable request has been sent to a remote device on this DLCI out this interface. The remote unit should respond by tearing down the logical loop on this DLCI.
TRAP-TYPE    

sfrapVloopUpViaRemote 92
A Vnip PVC loopback (VLOOP) request has been received from a remote device on this DLCI on this interface. The unit will respond by looping all data received on this PVC back out the interface towards the unit that initiated the request.
TRAP-TYPE    

sfrapVloopDownViaRemote 93
A request to disable a Vnip PVC loopback (VLOOP) on this unit with the indicated DLCI and Interface has been received. Usually this disable request is from the remote device that requested the VLOOP, however the request may also be due to a local event such as expiration of a locally configured loopback timeout. The unit will respond by tearing down the logical loop on this DLCI.
TRAP-TYPE    

sfrapVloopRequestFailed 94
The request for a PVC loopback (VLOOP) has been rejected or did not complete.
TRAP-TYPE    

sfrapVbertStarted 95
A Vnip PVC error rate test (VBERT) has been started on this DLCI out this interface to a remote device. The VBERT test data will be statistically multiplexed in with user data, management data, and networking data. The destination peer will echo this test data back to the source producing a full-duplex volume-based timed test.
TRAP-TYPE    

sfrapVbertStopped 96
A Vnip PVC BERT (VBERT) has been stopped on this DLCI on this interface to a remote device.
TRAP-TYPE    

sfrapVbertRequestFailed 97
The request for a PVC BERT (VBERT) on this DLCI on this interface has been rejected.
TRAP-TYPE    

sfrapDteSignalControlOnTrap 100
Unit's X.21 Control (C) DTE control signal is now active (on). This signal is presented by the external DTE device.
TRAP-TYPE    

sfrapDteSignalControlOffTrap 101
Unit's X.21 Control (C) DTE control signal is now inactive (off). This signal is presented by the external DTE device.
TRAP-TYPE    

sfrapDteSignalIndicateOnTrap 102
Unit's X.21 Indicate (I) DTE control signal is now active (on). This signal is presented by the external DTE device.
TRAP-TYPE    

sfrapDteSignalIndicateOffTrap 103
Unit's X.21 Indicate (I) DTE control signal is now inactive (off). This signal is presented by the external DTE device.
TRAP-TYPE    

sfrapPvcRxUtilizationExceededTrap 138
Percent utilization threshold was exceeded for the defined number of Short Term Intervals in the reception direction on this DLCI.
TRAP-TYPE    

sfrapPvcTxUtilizationExceededTrap 139
Percent utilization threshold was exceeded for the defined number of Short Term Intervals in the transmission direction on this DLCI.
TRAP-TYPE    

sfrapPvcRxUtilizationClearedTrap 140
Percent utilization was below the threshold for the defined number of Short Term Intervals in the reception direction on this DLCI.
TRAP-TYPE    

sfrapPvcTxUtilizationClearedTrap 141
Percent utilization was below the threshold for the defined number of Short Term Intervals in the transmission direction on this DLCI.
TRAP-TYPE    

sfrapConfigInstallSuccess 142
The configuration install process has successfully completed.
TRAP-TYPE    

sfrapTftpRequestedTrap 257
Unit has received a TFTP download request. TFTP is the preferred method for upgrading a unit's software image.
TRAP-TYPE    

sfrapTftpTransferringTrap 258
Unit has established a TFTP session, found the file, and begun the transfer. The file must still be qualified as appropriate for this unit.
TRAP-TYPE    

sfrapTftpProgrammingTrap 259
Unit has completed the TFTP transfer of a new software image which will next be programmed into non-volatile flash memory.
TRAP-TYPE    

sfrapTftpAbortedTrap 260
Unit's TFTP session was established but the transfer was aborted by user intervention or an unrecoverable TFTP protocol error.
TRAP-TYPE    

sfrapTftpSuccessTrap 261
Unit's TFTP download completed successfully. Flash devices will be programmed with a new image. Unit will stop passing data during the programming phase (less than a minute) and, upon completion, will reset and return to full operation using the new image.
TRAP-TYPE    

sfrapTftpHostUnreachableTrap 262
Unit could not establish a TFTP session with the designated server. Verify that the correct TFTP ip address, TFTP DLCI and TFTP interface are configured on the unit and also verify the TFTP server confguration.
TRAP-TYPE    

sfrapTftpNoFileTrap 263
Unit could not locate the designated file on the TFTP server. Verify the correct TFTP filename is configured on the unit and verify the location of this file on the server (file name may be case sensitive).
TRAP-TYPE    

sfrapTftpInvalidFileTrap 264
Unit had established a TFTP session and began transfer of the designated file. The unit aborted the transfer after determining that the specified file is not appropriate for this product (failed header verification).
TRAP-TYPE    

sfrapTftpCorruptFileTrap 265
Unit transferred the designated file but aborted the operation due to a checksum error within the downloaded s-record file.
TRAP-TYPE