RND-MIB

File: RND-MIB.mib (158453 bytes)

Imported modules

RFC1155-SMI RFC-1212 RFC1213-MIB
RFC-1215

Imported symbols

NetworkAddress IpAddress Counter
Gauge enterprises OBJECT-TYPE
DisplayString PhysAddress ipAddrEntry
TRAP-TYPE

Defined Types

TruthValue  
INTEGER true(1), false(2)    

RowStatus  
INTEGER active(1), notInService(2), notReady(3), createAndGo(4), createAndWait(5), destroy(6)    

NetNumber  
OCTET STRING Size(4)    

RndCommunityEntry  
SEQUENCE    
  rndCommunityMngStationAddr IpAddress
  rndCommunityString DisplayString
  rndCommunityAccess INTEGER
  rndCommunityTrapsEnable INTEGER
  rndCommunityStatus INTEGER

RndIfEntry  
SEQUENCE    
  rndIfIndex INTEGER
  rndIfBoardNum INTEGER
  rndIfNetAddress NetworkAddress
  rndIfStatus INTEGER
  rndIfClockType INTEGER
  rndIfBaudRate INTEGER
  rndIfCost INTEGER
  rndIfCompression INTEGER
  rndIfCompressionStatus INTEGER
  rndIfCompressionRate INTEGER
  rndIfLATCompression INTEGER
  rndIfCompressionType INTEGER
  rndIfFilterMode INTEGER
  rndIfChannelType INTEGER
  rndIfBridge INTEGER
  rndHighPriorityIf INTEGER
  rndWanHeader INTEGER
  rndDuplexMode INTEGER

RndIPXRipFilterGlbEntry  
SEQUENCE    
  rndIPXRipFilterGlbFLtype INTEGER
  rndIPXRipFilterGlbFLnumber INTEGER
  rndIPXRipFilterGlbFLStatus INTEGER
  rndIPXRipFilterGlbFLnetworkPatern OCTET STRING Size(4)
  rndIPXRipFilterGlbFLnetworkMask OCTET STRING Size(4)
  rndIPXRipFilterGlbFLaction INTEGER

RndIPXRipFilterCircuitEntry  
SEQUENCE    
  rndIPXRipFilterCircFLIfIndex INTEGER
  rndIPXRipFilterCircFLType INTEGER
  rndIPXRipFilterCircFLnumber INTEGER
  rndIPXRipFilterCircFLStatus INTEGER
  rndIPXRipFilterCircFLnetworkPatern OCTET STRING Size(4)
  rndIPXRipFilterCircFLnetworkMask OCTET STRING Size(4)
  rndIPXRipFilterCircFLaction INTEGER

RndIPXSapFilterGlbEntry  
SEQUENCE    
  rndIPXSapFilterGlbFLtype INTEGER
  rndIPXSapFilterGlbFLnumber INTEGER
  rndIPXSapFilterGlbFLStatus INTEGER
  rndIPXSapFilterGlbFLnetworkPatern OCTET STRING Size(4)
  rndIPXSapFilterGlbFLnetworkMask OCTET STRING Size(4)
  rndIPXSapFilterGlbFLserviceType INTEGER
  rndIPXSapFilterGlbFLserviceName OCTET STRING Size(1..48)
  rndIPXSapFilterGlbFLaction INTEGER

RndIPXSapFilterCircuitEntry  
SEQUENCE    
  rndIPXSapFilterCircFLIfIndex INTEGER
  rndIPXSapFilterCircFLtype INTEGER
  rndIPXSapFilterCircFLnumber INTEGER
  rndIPXSapFilterCircFLStatus INTEGER
  rndIPXSapFilterCircFLnetworkPatern OCTET STRING Size(4)
  rndIPXSapFilterCircFLnetworkMask OCTET STRING Size(4)
  rndIPXSapFilterCircFLserviceType INTEGER
  rndIPXSapFilterCircFLserviceName OCTET STRING Size(1..48)
  rndIPXSapFilterCircFLaction INTEGER

IpxBasicSysEntry  
SEQUENCE    
  ipxBasicSysInstance INTEGER
  ipxBasicSysExistState INTEGER
  ipxBasicSysInReceives Counter
  ipxBasicSysInHdrErrors Counter
  ipxBasicSysInUnknownSockets Counter
  ipxBasicSysInDiscards Counter
  ipxBasicSysInDelivers Counter
  ipxBasicSysNoRoutes Counter
  ipxBasicSysOutRequests Counter
  ipxBasicSysOutMalformedRequests Counter
  ipxBasicSysOutDiscards Counter
  ipxBasicSysOutPackets Counter

IpxCircEntry  
SEQUENCE    
  ipxCircSysInstance INTEGER
  ipxCircIndex INTEGER
  ipxCircExistState INTEGER
  ipxCircOperState INTEGER
  ipxCircIfIndex INTEGER
  ipxCircNetNumber NetNumber
  ipxCircTimeToNet INTEGER
  ipxCircEncaps INTEGER
  ipxCircNetbiosDeliver INTEGER

IpxDestEntry  
SEQUENCE    
  ipxDestSysInstance INTEGER
  ipxDestNetNum NetNumber
  ipxDestNextHopCircIndex INTEGER
  ipxDestProtocol INTEGER
  ipxDestTicks INTEGER
  ipxDestHopCount INTEGER
  ipxDestNextHopNICAddress PhysAddress
  ipxDestNextHopNetNum NetNumber
  ipxDestExistState INTEGER

IpxServEntry  
SEQUENCE    
  ipxServSysInstance INTEGER
  ipxServType OCTET STRING
  ipxServName OCTET STRING
  ipxServProtocol INTEGER
  ipxServNetNum NetNumber
  ipxServNode OCTET STRING
  ipxServSocket OCTET STRING
  ipxServHopCount INTEGER
  ipxServExistState INTEGER

RipSysEntry  
SEQUENCE    
  ripSysInstance INTEGER
  ripSysState INTEGER
  ripSysIncorrectPackets Counter

SapSysEntry  
SEQUENCE    
  sapSysInstance INTEGER
  sapSysState INTEGER
  sapSysIncorrectPackets Counter

RipCircEntry  
SEQUENCE    
  ripCircSysInstance INTEGER
  ripCircIndex INTEGER
  ripCircState INTEGER
  ripCircUpdate INTEGER
  ripCircAgeMultiplier INTEGER
  ripCircOutPackets Counter
  ripCircInPackets Counter

SapCircEntry  
SEQUENCE    
  sapCircSysInstance INTEGER
  sapCircIndex INTEGER
  sapCircState INTEGER
  sapCircUpdate INTEGER
  sapCircAgeMultiplier INTEGER
  sapCircGetNearestServerReply INTEGER
  sapCircOutPackets Counter
  sapCircInPackets Counter

RndFACSActEntry  
SEQUENCE    
  rndFACSActType INTEGER
  rndFACSActIfIndex INTEGER
  rndFACSAction INTEGER

RndFACSEntry  
SEQUENCE    
  rndFACSIfIndex INTEGER
  rndFACSProtocolType INTEGER
  rndFACSType INTEGER
  rndFACSIndex INTEGER
  rndFACSSrcAdd OCTET STRING
  rndFACSSrcAddMask OCTET STRING
  rndFACSDesAdd OCTET STRING
  rndFACSDesAddMask OCTET STRING
  rndFACSOperation INTEGER
  rndFACSNetFiltering INTEGER
  rndFACSSoketNum INTEGER
  rndFACSMask1Id INTEGER
  rndFACSMask2Id INTEGER
  rndFACSStatus INTEGER

RsIpAddrEntry  
SEQUENCE    
  rsIpAdEntAddr IpAddress
  rsIpAdEntIfIndex INTEGER
  rsIpAdEntNetMask IpAddress
  rsIpAdEntForwardIpBroadcast INTEGER
  rsIpAdEntBackupAddr IpAddress
  rsIpAdEntStatus INTEGER
  rsIpAdEntBcastAddr INTEGER

RsIcmpRdEntry  
SEQUENCE    
  rsIcmpRdIpAddr IpAddress
  rsIcmpRdIpAdvertAddr IpAddress
  rsIcmpRdMaxAdvertInterval INTEGER
  rsIcmpRdMinAdvertInterval INTEGER
  rsIcmpRdAdvertLifetime INTEGER
  rsIcmpRdAdvertise INTEGER
  rsIcmpRdPreferenceLevel INTEGER
  rsIcmpRdEntStatus INTEGER

RsRip2IfConfEntry  
SEQUENCE    
  rsRip2IfConfAddress IpAddress
  rsRip2IfConfVirtualDis INTEGER
  rsRip2IfConfAutoSend INTEGER

IpRedundRoutersEntry  
SEQUENCE    
  ipRedundRoutersIfAddr IpAddress
  ipRedundRoutersMainRouterAddr IpAddress
  ipRedundRoutersOperStatus INTEGER
  ipRedundRoutersPollInterval INTEGER
  ipRedundRoutersTimeout INTEGER
  ipRedundRoutersStatus INTEGER

RsIpRipFilterGlbEntry  
SEQUENCE    
  rsIpRipFilterGlbType INTEGER
  rsIpRipFilterGlbNumber INTEGER
  rsIpRipFilterGlbStatus INTEGER
  rsIpRipFilterGlbIpAddr IpAddress
  rsIpRipFilterGlbNetworkMaskBits INTEGER
  rsIpRipFilterGlbMatchBits INTEGER
  rsIpRipFilterGlbAction INTEGER

RsIpRipFilterLclEntry  
SEQUENCE    
  rsIpRipFilterLclIpIntf IpAddress
  rsIpRipFilterLclType INTEGER
  rsIpRipFilterLclNumber INTEGER
  rsIpRipFilterLclStatus INTEGER
  rsIpRipFilterLclIpAddr IpAddress
  rsIpRipFilterLclNetworkMaskBits INTEGER
  rsIpRipFilterLclMatchBits INTEGER
  rsIpRipFilterLclAction INTEGER

VirtualLanEntry  
SEQUENCE    
  vlIfIndex INTEGER
  vlProto INTEGER
  vlAutoConfigEnable TruthValue
  vlStatus RowStatus
  vlType INTEGER

VirtualLanPortEntry  
SEQUENCE    
  vLIfIndex INTEGER
  vLPortIfIndex INTEGER
  vLPortType INTEGER
  vLPortStatus RowStatus

VirtualLanAutoConfEntry  
SEQUENCE    
  vlAutoConfProto INTEGER
  vlAutoConfPortIfIndex INTEGER
  vlAutoConfStatus RowStatus

RsIfType  
INTEGER ppp(23), frameRelay(32), virtualNet(500), rndWan(1000), cod(1001), backup(1002), fr1490(1003), b1isdn(1010), b2isdn(1011), unknown(1100)    

RsIfConfEntry  
SEQUENCE    
  rsIfConfIndex INTEGER
  rsIfConfType RsIfType
  rsIfConfName DisplayString
  rsIfConfStatus RowStatus

EventMessageEntry  
SEQUENCE    
  eventNum INTEGER
  eventDesc DisplayString

ReaBridgeFftEntry  
SEQUENCE    
  reaBrgFftEntryNum INTEGER
  reaBrgFftMacAddr PhysAddress
  reaBrgFftReNum INTEGER
  reaBrgFftPortNum INTEGER
  reaBrgFftFacsSrcIndex INTEGER
  reaBrgFftFacsDstIndex INTEGER

ReaIpFftEntry  
SEQUENCE    
  reaIpFftEntryNum INTEGER
  reaIpFftDstIpAddr IpAddress
  reaIpFftDstIpMask IpAddress
  reaIpFftRangeType INTEGER
  reaIpFftSrcMacAddr PhysAddress
  reaIpFftDstMacAddr PhysAddress
  reaIpFftReNum INTEGER
  reaIpFftPortNum INTEGER
  reaIpFftFacsSrcIndex INTEGER
  reaIpFftFacsDstIndex INTEGER
  reaIpFftApplFlags OCTET STRING

ReaIpxFftEntry  
SEQUENCE    
  reaIpxFftEntryNum INTEGER
  reaIpxFftDstNetid INTEGER
  reaIpxFftRangeType INTEGER
  reaIpxFftSrcMacAddr PhysAddress
  reaIpxFftDstMacAddr PhysAddress
  reaIpxFftReNum INTEGER
  reaIpxFftPortNum INTEGER
  reaIpxFftFacsSrcIndex INTEGER
  reaIpxFftFacsDstIndex INTEGER

LreVnResposibilityEntry  
SEQUENCE    
  lreVnRespVn INTEGER
  lreVnRespStatus RowStatus

RndMonitoredElementEntry  
SEQUENCE    
  rndMonitoredElementAddress IpAddress
  rndMonitoredElementCommunity DisplayString Size(1..20)
  rndMonitoredElementLabel DisplayString Size(1..20)
  rndDefaultPollingInterval INTEGER
  rndDefaultLogFile DisplayString
  rndMonitoredElementStatus RowStatus

RndMonitoringEntry  
SEQUENCE    
  rndMonitoredElement DisplayString Size(1..20)
  rndMonitoredObjectInstanceLabel DisplayString
  rndMonitoredObjectName DisplayString
  rndMonitoredObjectIdentifier OBJECT IDENTIFIER
  rndMonitoredObjectInstance OBJECT IDENTIFIER
  rndMonitoredObjectSyntax INTEGER
  rndMonitoringInterval INTEGER
  rndAlarmMaxTreshold INTEGER
  rndAlarmMinTreshold INTEGER
  rndMonitoringLogfile DisplayString
  rndMonitoringEntryStatus RowStatus

RndMibFileEntry  
SEQUENCE    
  rndMibFileIndex INTEGER
  rndMibFilePath DisplayString
  rndMibFileRefresh INTEGER
  rndMibFileEntryStatus RowStatus

RndDeleteValuesEntry  
SEQUENCE    
  rndRowStatusVariableName DisplayString
  rndRowStatusObjectId OBJECT IDENTIFIER
  rndRowDeleteValue INTEGER
  rndDeleteValueEntryStatus RowStatus

RsIpZhrStatusEntry  
SEQUENCE    
  rsIpZhrStatusIpIntf IpAddress
  rsIpZhrAdminStatus INTEGER

RsIpZhrVirtAddressEntry  
SEQUENCE    
  rsIpZhrVirtAddressIpIntf IpAddress
  rsIpZhrVirtAddressTo IpAddress
  rsIpZhrVirtAddressFrom IpAddress
  rsIpZhrVirtAddressStatus RowStatus

RsIpZhrConnectionEntry  
SEQUENCE    
  rsIpZhrConnectionIpIntf IpAddress
  rsIpZhrConnectionSrcIp IpAddress
  rsIpZhrConnectionDestIp IpAddress
  rsIpZhrConnectionVirtualIp IpAddress
  rsIpZhrConnectionType INTEGER
  rsIpZhrConnectionAge INTEGER
  rsIpZhrConnectionStatus RowStatus

Defined Values

rnd 1.3.6.1.4.1.89
OBJECT IDENTIFIER    

rndMng 1.3.6.1.4.1.89.1
OBJECT IDENTIFIER    

rndSysId 1.3.6.1.4.1.89.1.1
Identification of an RND device. The device type for each integer clarifies the sysObjectID in MIB - II.
OBJECT-TYPE    
  INTEGER reb(1), ceb(2), ceblb(3), xeb(4), xeb1(5), rebsx(6), rtb(7), ltb(8), lte(9), iprouter(10), ielb(11), leb(12), openGate12(13), openGate4(14), ran(15), itlb(16), gatelinx(17), openGate2(18), ogRanTR(19), stc(20), ftc(21), armon(22), fccs1004(23), fccs1012(24), rdapter(25), ogvan(26), wanGate(27), ogRubE(28), ogRubT(29), elX(30), vGate4(31), mrt(32), ogSrubET(33), vanXS(34), lre(35), vGate2(36), serverDispatcher4(37), serverDispatcher2(38), vGate2Fast(39), serverDispatcher2Fast(40), prt(41), mlm(42), prt11(43), quickOffice(44), apollo(45)  

rndAction 1.3.6.1.4.1.89.1.2
This variable enables the operator to perform one of the specified actions on the tables maintained by the network device. Send actions require support of proprietery File exchange protocol.
OBJECT-TYPE    
  INTEGER reset(1), sendNetworkTab(2), deleteNetworkTab(3), sendRoutingTab(4), deleteRoutingTab(5), sendLanTab(6), deleteLanTab(7), deleteArpTab(8), sendArpTab(9), deleteRouteTab(10), sendRouteTab(11), backupSPFRoutingTab(12), backupIPRoutingTab(13), backupNetworkTab(14), backupLanTab(15), backupArpTab(16), backupIPXRipTab(17), backupIPXSAPTab(18), resetCDB(19), eraseCDB(20), deleteZeroHopRoutingAllocTab(21)  

rndFileName 1.3.6.1.4.1.89.1.3
The name of the file used internally by RND for transferring tables maintained by network devices, using a prorietary File exchange protocol.
OBJECT-TYPE    
  OCTET STRING  

rndDeviceParams 1.3.6.1.4.1.89.2
OBJECT IDENTIFIER    

rndBridgeType 1.3.6.1.4.1.89.2.1
Identification of the RND bridge type.
OBJECT-TYPE    
  INTEGER reb(1), ceb(2), ceblb(3), xeb(4), xeb1(5), rebsx(6), rtb(7), ltb(8), tre(9), rtre(10), xtb(11), ete(12), rete(13), ielb(30), leb(31), openGate12(32), openGate4(33), ran(34), itlb(35), gatelinx(36), openGate2(37), ogRanTR(38), rdapter(39), ogVan(40), wanGate(41), ogRubE(42), ogRubT(43), wanGateI(44), vGate4(45), lre(46), mrt(47), vGate2(48)  

rndInactiveArpTimeOut 1.3.6.1.4.1.89.2.2
This variable defines the maximum time period that can pass between ARP requests concerning an entry in the ARP table. After this time period, the entry is deleted from the table.
OBJECT-TYPE    
  INTEGER  

rndBridgeAlarm 1.3.6.1.4.1.89.2.3
OBJECT IDENTIFIER    

rndErrorDesc 1.3.6.1.4.1.89.2.3.1
A textual description of the enterprise-specific trap sent to the Network Management Station by the RND managed device.
OBJECT-TYPE    
  DisplayString  

rndErrorSeverity 1.3.6.1.4.1.89.2.3.2
The severity type of the enterprise-specific trap sent to the Network Management Station by the RND managed device.
OBJECT-TYPE    
  INTEGER  

rndBrgVersion 1.3.6.1.4.1.89.2.4
The bridge version.
OBJECT-TYPE    
  DisplayString  

rndBrgFeatures 1.3.6.1.4.1.89.2.5
A bit mask that defines the features supported by a particular configuration of this network element: __________________________________________ | Byte 1|Byte 2 |Byte 3 | ....|Byte 20 | |87654321| | 87654321| |________|_______________________________| Byte1 : bit1: TX Block mask bit2: Source Routing Encapulation bit3: SNA/SDLC bit4: Frame Relay bit5: SNMP bit6: LAN Manager bit7: High Performance bit8: Translation Byte2 : bit1: DEC Router bit2: IPX Router bit3: IP Router Byte3 : bit1: Dial Up Backup bit2: COD bit3: FACS bit4: Load Balance bit5: Remote Configuration bit6: RIP 2 bit7: OSPF bit8: IPX RIP/SAP Filter Byte4 : bit1: BootP Server bit2: BootP Client bit3: Compression bit4: V25.bis bit5: ISDN bit6: CODv2 bit7: NSPF bit8: UDP Relay Byte5 bit1:VirtualLAN bit2:Static IP Multicast bit3:IP Redundancy bit4:CCM2 bit5:ISDN Bonding bit6:Backup Link Selection -- for the VAN/Rdapter ver 4.0 bit7:IP/IPX Forwarding -- for the WANgate ver 4.0 bit8:Improved COD Byte6 bit1: Server Disptacher bit2: ISDN_US -- for the VANSX/WANGATE ver 5.0 bit3: PPP bit4: IP Rip Filter -- for Vgate3 bit5: Zero Hop Routing -- for Vgate3 bit6: ISDN Japan Byte7 bit1: With unmanaged Switch bit2: 2 LANs bit3: OSPF Ver 2.0 bit4: FACS Ver 2.0 bit5: Multiple WEB Farm bit6: Backup Server
OBJECT-TYPE    
  OCTET STRING  

rndBrgLicense 1.3.6.1.4.1.89.2.6
This parameter is used for entering a s/w license number for a device. A separate license number is supplied for each device.
OBJECT-TYPE    
  OCTET STRING  

rndIpHost 1.3.6.1.4.1.89.2.7
OBJECT IDENTIFIER    

rndICMPTransmitionEnable 1.3.6.1.4.1.89.2.7.1
This variable controlls the ability to transmit ICMP frames
OBJECT-TYPE    
  INTEGER enable(1), disable(2)  

rndCommunityTable 1.3.6.1.4.1.89.2.7.2
The community table of the agent
OBJECT-TYPE    
  SEQUENCE OF  
    RndCommunityEntry

rndCommunityEntry 1.3.6.1.4.1.89.2.7.2.1
The row definition for this table.
OBJECT-TYPE    
  RndCommunityEntry  

rndCommunityMngStationAddr 1.3.6.1.4.1.89.2.7.2.1.1
The management station that will be allowed to communicate with the agent IP address
OBJECT-TYPE    
  IpAddress  

rndCommunityString 1.3.6.1.4.1.89.2.7.2.1.2
The community string with which the management station will communicate with the agent
OBJECT-TYPE    
  DisplayString Size(1..20)  

rndCommunityAccess 1.3.6.1.4.1.89.2.7.2.1.3
The allowed access to this management station
OBJECT-TYPE    
  INTEGER readOnly(1), readWrite(2), super(3)  

rndCommunityTrapsEnable 1.3.6.1.4.1.89.2.7.2.1.4
Should the agent send traps to the management station
OBJECT-TYPE    
  INTEGER trapsEnable(1), trapsDisable(2)  

rndCommunityStatus 1.3.6.1.4.1.89.2.7.2.1.5
The status of this entry. If the status is invalid the community entry will be deleted
OBJECT-TYPE    
  INTEGER enable(1), invalid(2)  

rndManagedTime 1.3.6.1.4.1.89.2.8
The time will be sent in the format hhmmss
OBJECT-TYPE    
  DisplayString Size(6)  

rndManagedDate 1.3.6.1.4.1.89.2.9
The date will be sent in the format ddmmyyyy
OBJECT-TYPE    
  DisplayString Size(6..8)  

genGroup 1.3.6.1.4.1.89.2.11
OBJECT IDENTIFIER    

genGroupHWVersion 1.3.6.1.4.1.89.2.11.1
Defines the HW version of the product.
OBJECT-TYPE    
  DisplayString  

genGroupConfigurationSymbol 1.3.6.1.4.1.89.2.11.2
Defines the Configuration Symbol attached to any hardware module manufactured by LANNET. One single character A..Z defines the CS version.
OBJECT-TYPE    
  DisplayString Size(1)  

genGroupHWStatus 1.3.6.1.4.1.89.2.11.3
This attribute describes the status of the group hardware as detected by the sensors software.
OBJECT-TYPE    
  INTEGER ok(1), hardwareProblems(2), notSupported(255)  

rndInterface 1.3.6.1.4.1.89.4
OBJECT IDENTIFIER    

rndIfTable 1.3.6.1.4.1.89.4.1
RND-specific interface table. Each table entry includes an index, Board number, Network Address, interface status, clock indicator and interface cost.
OBJECT-TYPE    
  SEQUENCE OF  
    RndIfEntry

rndIfEntry 1.3.6.1.4.1.89.4.1.1
The row definition for this table.
OBJECT-TYPE    
  RndIfEntry  

rndIfIndex 1.3.6.1.4.1.89.4.1.1.1
Index to the RND Interface Table. The interface defined by a particular value of this index is the same interface as identified by the same value of ifIndex (MIBII).
OBJECT-TYPE    
  INTEGER  

rndIfBoardNum 1.3.6.1.4.1.89.4.1.1.2
The interface defined by this entry correspTnds to the board defined by the same value of rndSlotBoardNum in the rndSlotTab.
OBJECT-TYPE    
  INTEGER  

rndIfNetAddress 1.3.6.1.4.1.89.4.1.1.3
The IP address of the interface defined by the particular value of rndIfIndex.
OBJECT-TYPE    
  NetworkAddress  

rndIfStatus 1.3.6.1.4.1.89.4.1.1.4
The current status of the interface.
OBJECT-TYPE    
  INTEGER ok(1), okSingleBrg(2), okMultiBrg(3), connctFault(4), rxFault(5), txFault(6), channelLoopback(7), rxClockFault(8), t1Alarm(9)  

rndIfClockType 1.3.6.1.4.1.89.4.1.1.5
rndIfClockType defines the type of clock each interface uses: internal or external.
OBJECT-TYPE    
  INTEGER external(1), internal(2), t1(3), g703(4)  

rndIfBaudRate 1.3.6.1.4.1.89.4.1.1.6
Defines the baud rate of use by the interface. The valid rates are determined by the type of the media for which this baud rate is defined.
OBJECT-TYPE    
  INTEGER  

rndIfCost 1.3.6.1.4.1.89.4.1.1.7
This variable assigns a transmission cost to the interface (channel or LAN). These costs are used in Level II routing. The costs aretypically inversly proportional to the channel quality.
OBJECT-TYPE    
  INTEGER  

rndIfCompression 1.3.6.1.4.1.89.4.1.1.8
Defines whether data compression is enabled or disabled for the interface.
OBJECT-TYPE    
  INTEGER enable(1), disable(2)  

rndIfCompressionStatus 1.3.6.1.4.1.89.4.1.1.9
Defines the status of the compression component: not-inserted - Compression component is not in the device active - Compression is enabled and operates correctly not-active - Compression is enables but does not operate. The reason may be that there is no compression component on the device connected to this interface. disabled - Compression was disabled by management, using variable rndCompression.
OBJECT-TYPE    
  INTEGER not-inserted(1), active(2), not-active(3), disable(4)  

rndIfCompressionRate 1.3.6.1.4.1.89.4.1.1.10
Percentage of compression. This variable applies only if rndCompressionStatus is active.
OBJECT-TYPE    
  INTEGER  

rndIfLATCompression 1.3.6.1.4.1.89.4.1.1.11
Enable/Disable the LAT Compression.
OBJECT-TYPE    
  INTEGER enable(1), disable(2)  

rndIfCompressionType 1.3.6.1.4.1.89.4.1.1.12
This parameter indicates the type of compression option available in the device. none(1) - indicates that there is no compression option in the device lowSpeed(2) - indicates a compression option which is operational up to line speed sof 64 kbps. highSpeed(3)- indicates a compression option which is operational up to line speeds of 2 Mbps.
OBJECT-TYPE    
  INTEGER none(1), lowSpeed(2), highSpeed(3)  

rndIfFilterMode 1.3.6.1.4.1.89.4.1.1.13
This parameter indicates the type of filtering in the device.
OBJECT-TYPE    
  INTEGER destinationOnly(1), sourceAndDestination(2), none(3)  

rndIfChannelType 1.3.6.1.4.1.89.4.1.1.14
The type of the WAN channel
OBJECT-TYPE    
  INTEGER wanChannel(1), ogRanPort(2), routerToBridge(3), spsFramRelay(4), dialBackup(5), snar(6), lan(7), spsX25(8), frameRelay1490(9), frameRelay1490CAR(10), frameRelayCAR(11), ppp(12)  

rndIfBridge 1.3.6.1.4.1.89.4.1.1.15
This variable indicates whether this interface forward Layer II pakages.
OBJECT-TYPE    
  INTEGER enable(1), disable(2)  

rndHighPriorityIf 1.3.6.1.4.1.89.4.1.1.16
This variable indicates whether this interface will forward pakages that fit HighPriority set by the manager.
OBJECT-TYPE    
  INTEGER enable(1), disable(2)  

rndWanHeader 1.3.6.1.4.1.89.4.1.1.17
This variable indicates the RND WAN header type used for frames which pass through this interface. 'regular' specifies a 14 bytes header compatible with older OG versions and 'short' a 4 byte header compatible with the RND adapter product family.
OBJECT-TYPE    
  INTEGER regular(1), short(2)  

rndDuplexMode 1.3.6.1.4.1.89.4.1.1.18
This variable indicates whether this interface operates in half duplex full duplex or auto negotiation mode.
OBJECT-TYPE    
  INTEGER half(1), full(2)  

rndIPX 1.3.6.1.4.1.89.12
OBJECT IDENTIFIER    

rndIPXdriver 1.3.6.1.4.1.89.12.1
OBJECT IDENTIFIER    

rndIPXRip 1.3.6.1.4.1.89.12.2
OBJECT IDENTIFIER    

rndIPXRipFilterGlbTable 1.3.6.1.4.1.89.12.2.10
The table of RIP global filters per IPX router.
OBJECT-TYPE    
  SEQUENCE OF  
    RndIPXRipFilterGlbEntry

rndIPXRipFilterGlbEntry 1.3.6.1.4.1.89.12.2.10.1
An entry in the RIP global filter table
OBJECT-TYPE    
  RndIPXRipFilterGlbEntry  

rndIPXRipFilterGlbFLtype 1.3.6.1.4.1.89.12.2.10.1.1
Type of filter - input/output
OBJECT-TYPE    
  INTEGER input(1), output(2)  

rndIPXRipFilterGlbFLnumber 1.3.6.1.4.1.89.12.2.10.1.2
Number of RIP filter.
OBJECT-TYPE    
  INTEGER  

rndIPXRipFilterGlbFLStatus 1.3.6.1.4.1.89.12.2.10.1.3
The validity of this entry. An entry with this value set to invalid may be deleted from the table with IPX implementation's discretion.
OBJECT-TYPE    
  INTEGER valid(1), invalid(2), underCreation(3)  

rndIPXRipFilterGlbFLnetworkPatern 1.3.6.1.4.1.89.12.2.10.1.4
Number of filtered network. Value 0xFFFFFFFF applies for any network.
OBJECT-TYPE    
  OCTET STRING Size(4)  

rndIPXRipFilterGlbFLnetworkMask 1.3.6.1.4.1.89.12.2.10.1.5
Network mask
OBJECT-TYPE    
  OCTET STRING Size(4)  

rndIPXRipFilterGlbFLaction 1.3.6.1.4.1.89.12.2.10.1.6
Filter action - permit/deny for this network
OBJECT-TYPE    
  INTEGER deny(1), permit(2)  

rndIPXRipFilterCircuitTable 1.3.6.1.4.1.89.12.2.11
Table of input/output RIP filters used per IPX circuit number.
OBJECT-TYPE    
  SEQUENCE OF  
    RndIPXRipFilterCircuitEntry

rndIPXRipFilterCircuitEntry 1.3.6.1.4.1.89.12.2.11.1
An entry in the Circuit RIP filter table
OBJECT-TYPE    
  RndIPXRipFilterCircuitEntry  

rndIPXRipFilterCircFLIfIndex 1.3.6.1.4.1.89.12.2.11.1.1
The Interface identifier for this filter. This value correspond to rndIPXIfIndex or ipxCircIndex for ET16
OBJECT-TYPE    
  INTEGER  

rndIPXRipFilterCircFLType 1.3.6.1.4.1.89.12.2.11.1.2
Type of filter - input/output
OBJECT-TYPE    
  INTEGER input(1), output(2)  

rndIPXRipFilterCircFLnumber 1.3.6.1.4.1.89.12.2.11.1.3
Number of RIP filter for this circuit
OBJECT-TYPE    
  INTEGER  

rndIPXRipFilterCircFLStatus 1.3.6.1.4.1.89.12.2.11.1.4
The validity of this entry. An entry with this value set to invalid may be deleted from the table with IPX implementation's discretion.
OBJECT-TYPE    
  INTEGER valid(1), invalid(2), underCreation(3)  

rndIPXRipFilterCircFLnetworkPatern 1.3.6.1.4.1.89.12.2.11.1.5
Number of filtered network. Value 0xFFFFFFFF applies for any network.
OBJECT-TYPE    
  OCTET STRING Size(4)  

rndIPXRipFilterCircFLnetworkMask 1.3.6.1.4.1.89.12.2.11.1.6
Network mask
OBJECT-TYPE    
  OCTET STRING Size(4)  

rndIPXRipFilterCircFLaction 1.3.6.1.4.1.89.12.2.11.1.7
Filter action - permit/deny
OBJECT-TYPE    
  INTEGER deny(1), permit(2)  

rndIPXSap 1.3.6.1.4.1.89.12.3
OBJECT IDENTIFIER    

rndIPXSapFilterGlbTable 1.3.6.1.4.1.89.12.3.10
The table of SAP global filter susedper IPX router.
OBJECT-TYPE    
  SEQUENCE OF  
    RndIPXSapFilterGlbEntry

rndIPXSapFilterGlbEntry 1.3.6.1.4.1.89.12.3.10.1
An entry in the SAP global filter table
OBJECT-TYPE    
  RndIPXSapFilterGlbEntry  

rndIPXSapFilterGlbFLtype 1.3.6.1.4.1.89.12.3.10.1.1
Type of filter-input/output
OBJECT-TYPE    
  INTEGER input(1), output(2)  

rndIPXSapFilterGlbFLnumber 1.3.6.1.4.1.89.12.3.10.1.2
Number of SAP filter.
OBJECT-TYPE    
  INTEGER  

rndIPXSapFilterGlbFLStatus 1.3.6.1.4.1.89.12.3.10.1.3
The validity of this entry. An entry with this value set to invalid may be deleted from the table with IPX implementation's discretion.
OBJECT-TYPE    
  INTEGER valid(1), invalid(2), underCreation(3)  

rndIPXSapFilterGlbFLnetworkPatern 1.3.6.1.4.1.89.12.3.10.1.4
Number network of the filter edservice. Value 0xFFFFFFFF applies for any network.
OBJECT-TYPE    
  OCTET STRING Size(4)  

rndIPXSapFilterGlbFLnetworkMask 1.3.6.1.4.1.89.12.3.10.1.5
Network mask
OBJECT-TYPE    
  OCTET STRING Size(4)  

rndIPXSapFilterGlbFLserviceType 1.3.6.1.4.1.89.12.3.10.1.6
The type of the service which may be filtered ;value0xFFFF applies for all types of service and it's default
OBJECT-TYPE    
  INTEGER  

rndIPXSapFilterGlbFLserviceName 1.3.6.1.4.1.89.12.3.10.1.7
The name of the service which may be filtered; wild cardas * may be used in end of the name.
OBJECT-TYPE    
  OCTET STRING Size(1..48)  

rndIPXSapFilterGlbFLaction 1.3.6.1.4.1.89.12.3.10.1.8
Filter mode - permit/deny for this service
OBJECT-TYPE    
  INTEGER deny(1), permit(2)  

rndIPXSapFilterCircuitTable 1.3.6.1.4.1.89.12.3.11
Table of input/output SAP filter susedper IPX circuit number.
OBJECT-TYPE    
  SEQUENCE OF  
    RndIPXSapFilterCircuitEntry

rndIPXSapFilterCircuitEntry 1.3.6.1.4.1.89.12.3.11.1
An entry in the Circuit SAP filter table
OBJECT-TYPE    
  RndIPXSapFilterCircuitEntry  

rndIPXSapFilterCircFLIfIndex 1.3.6.1.4.1.89.12.3.11.1.1
The Interface identifier for this filter. This value correspondtornd IPXIfIndex or ipxCircIndex for ET16
OBJECT-TYPE    
  INTEGER  

rndIPXSapFilterCircFLtype 1.3.6.1.4.1.89.12.3.11.1.2
Type of filter-input/output
OBJECT-TYPE    
  INTEGER input(1), output(2)  

rndIPXSapFilterCircFLnumber 1.3.6.1.4.1.89.12.3.11.1.3
Number of SAP filter. Th is value correspondto rndIPXSapFilterNumber
OBJECT-TYPE    
  INTEGER  

rndIPXSapFilterCircFLStatus 1.3.6.1.4.1.89.12.3.11.1.4
The validity of this entry. An entry with this value set to invalid may be deleted from the table with IPX implementation's discretion.
OBJECT-TYPE    
  INTEGER valid(1), invalid(2), underCreation(3)  

rndIPXSapFilterCircFLnetworkPatern 1.3.6.1.4.1.89.12.3.11.1.5
Number network of the filtered service. Value 0xFFFFFFFF applies for any network.
OBJECT-TYPE    
  OCTET STRING Size(4)  

rndIPXSapFilterCircFLnetworkMask 1.3.6.1.4.1.89.12.3.11.1.6
Network mask
OBJECT-TYPE    
  OCTET STRING Size(4)  

rndIPXSapFilterCircFLserviceType 1.3.6.1.4.1.89.12.3.11.1.7
The type of the service which may be filtered; value 0xFFFF applies for all types of service and it's default
OBJECT-TYPE    
  INTEGER  

rndIPXSapFilterCircFLserviceName 1.3.6.1.4.1.89.12.3.11.1.8
The name of the service which may be filtered; wild cardas * may be used i n end of the name.
OBJECT-TYPE    
  OCTET STRING Size(1..48)  

rndIPXSapFilterCircFLaction 1.3.6.1.4.1.89.12.3.11.1.9
Filter mode-permit/deny
OBJECT-TYPE    
  INTEGER deny(1), permit(2)  

ipxSystem 1.3.6.1.4.1.89.12.4
OBJECT IDENTIFIER    

ipxBasicSysTable 1.3.6.1.4.1.89.12.4.1
The IPX System table - basic information.
OBJECT-TYPE    
  SEQUENCE OF  
    IpxBasicSysEntry

ipxBasicSysEntry 1.3.6.1.4.1.89.12.4.1.1
Each entry corresponds to one instance of IPX running on the system.
OBJECT-TYPE    
  IpxBasicSysEntry  

ipxBasicSysInstance 1.3.6.1.4.1.89.12.4.1.1.1
The unique identifier of the instance of IPX to which this row corresponds. This value may be written only when creating a new entry in the table.
OBJECT-TYPE    
  INTEGER  

ipxBasicSysExistState 1.3.6.1.4.1.89.12.4.1.1.2
The validity of this entry in the IPX system table. Setting this field to off indicates that this entry may be deleted from the system table at the IPX implementation's discretion.
OBJECT-TYPE    
  INTEGER off(1), on(2)  

ipxBasicSysInReceives 1.3.6.1.4.1.89.12.4.1.1.3
The total number of IPX packets received, including those received in error.
OBJECT-TYPE    
  Counter  

ipxBasicSysInHdrErrors 1.3.6.1.4.1.89.12.4.1.1.4
The number of IPX packets discarded due to errors in their headers, including any IPX packet with a size less than the minimum of 30 bytes.
OBJECT-TYPE    
  Counter  

ipxBasicSysInUnknownSockets 1.3.6.1.4.1.89.12.4.1.1.5
The number of IPX packets discarded because the destination socket was not open.
OBJECT-TYPE    
  Counter  

ipxBasicSysInDiscards 1.3.6.1.4.1.89.12.4.1.1.6
The number of IPX packets received but discarded due to reasons other than those accounted for by ipxBasicSysInHdrErrors, ipxBasicSysInUnknownSockets, ipxAdvSysInDiscards, and ipxAdvSysInCompressDiscards.
OBJECT-TYPE    
  Counter  

ipxBasicSysInDelivers 1.3.6.1.4.1.89.12.4.1.1.7
The total number of IPX packets delivered locally, including packets from local applications.
OBJECT-TYPE    
  Counter  

ipxBasicSysNoRoutes 1.3.6.1.4.1.89.12.4.1.1.8
The number of times no route to a destination was found.
OBJECT-TYPE    
  Counter  

ipxBasicSysOutRequests 1.3.6.1.4.1.89.12.4.1.1.9
The number of IPX packets supplied locally for transmission, not including any packets counted in ipxAdvForwPackets.
OBJECT-TYPE    
  Counter  

ipxBasicSysOutMalformedRequests 1.3.6.1.4.1.89.12.4.1.1.10
The number of IPX packets supplied locally that contained errors in their structure.
OBJECT-TYPE    
  Counter  

ipxBasicSysOutDiscards 1.3.6.1.4.1.89.12.4.1.1.11
The number of outgoing IPX packets discarded due to reasons other than those accounted for in ipxBasicSysOutMalformedRequests, ipxAdvSysOutFiltered, and ipxAdvSysOutCompressDiscards.
OBJECT-TYPE    
  Counter  

ipxBasicSysOutPackets 1.3.6.1.4.1.89.12.4.1.1.12
The total number of IPX packets transmitted.
OBJECT-TYPE    
  Counter  

ipxCircuit 1.3.6.1.4.1.89.12.5
OBJECT IDENTIFIER    

ipxCircTable 1.3.6.1.4.1.89.12.5.1
The Circuit table.
OBJECT-TYPE    
  SEQUENCE OF  
    IpxCircEntry

ipxCircEntry 1.3.6.1.4.1.89.12.5.1.1
Each entry corresponds to one circuit known to the system.
OBJECT-TYPE    
  IpxCircEntry  

ipxCircSysInstance 1.3.6.1.4.1.89.12.5.1.1.1
The unique identifier of the instance of IPX to which this entry corresponds. This value may be written only when creating a new entry in the table.
OBJECT-TYPE    
  INTEGER  

ipxCircIndex 1.3.6.1.4.1.89.12.5.1.1.2
The identifier of this circuit, unique within the instance of IPX. This value may be written only when creating a new entry in the table.
OBJECT-TYPE    
  INTEGER  

ipxCircExistState 1.3.6.1.4.1.89.12.5.1.1.3
The validity of this circuit entry. A circuit with this value set to off may be deleted from the table at the IPX implementation's discretion.
OBJECT-TYPE    
  INTEGER off(1), on(2), sleeping(3)  

ipxCircOperState 1.3.6.1.4.1.89.12.5.1.1.4
The operational state of the circuit.
OBJECT-TYPE    
  INTEGER down(1), up(2)  

ipxCircIfIndex 1.3.6.1.4.1.89.12.5.1.1.5
The value of ifIndex for the interface used by this circuit. This value may be written only when creating a new entry in the table.
OBJECT-TYPE    
  INTEGER  

ipxCircNetNumber 1.3.6.1.4.1.89.12.5.1.1.6
The IPX network number of this circuit. This value may be written only when creating a new entry in the table.
OBJECT-TYPE    
  NetNumber  

ipxCircTimeToNet 1.3.6.1.4.1.89.12.5.1.1.7
The time to net value associated with this interface, in term of 1/18ths of a second.
OBJECT-TYPE    
  INTEGER 1..65535  

ipxCircEncaps 1.3.6.1.4.1.89.12.5.1.1.8
The encapsulation method associated with this interface.
OBJECT-TYPE    
  INTEGER novell(1), ethernet(2), llc(3), snap(4), none(10)  

ipxCircNetbiosDeliver 1.3.6.1.4.1.89.12.5.1.1.9
Deliver NetBios All Networks Broadcast Packets
OBJECT-TYPE    
  INTEGER enabled(1), disabled(2)  

ipxForwarding 1.3.6.1.4.1.89.12.6
OBJECT IDENTIFIER    

ipxDestTable 1.3.6.1.4.1.89.12.6.1
The Destination table contains information about all known destinations.
OBJECT-TYPE    
  SEQUENCE OF  
    IpxDestEntry

ipxDestEntry 1.3.6.1.4.1.89.12.6.1.1
Each entry corresponds to one destination.
OBJECT-TYPE    
  IpxDestEntry  

ipxDestSysInstance 1.3.6.1.4.1.89.12.6.1.1.1
The unique identifier of the instance of IPX to which this row corresponds.
OBJECT-TYPE    
  INTEGER  

ipxDestNetNum 1.3.6.1.4.1.89.12.6.1.1.2
The IPX network number of the destination.
OBJECT-TYPE    
  NetNumber  

ipxDestNextHopCircIndex 1.3.6.1.4.1.89.12.6.1.1.3
The unique identifier of the circuit used to reach the next hop.
OBJECT-TYPE    
  INTEGER  

ipxDestProtocol 1.3.6.1.4.1.89.12.6.1.1.4
The routing protocol from which knowledge of this destination was obtained.
OBJECT-TYPE    
  INTEGER other(1), local(2), rip(3), nlsp(4), static(5)  

ipxDestTicks 1.3.6.1.4.1.89.12.6.1.1.5
The delay in ticks to reach this destination.
OBJECT-TYPE    
  INTEGER  

ipxDestHopCount 1.3.6.1.4.1.89.12.6.1.1.6
The number of hops necessary to reach the destination.
OBJECT-TYPE    
  INTEGER  

ipxDestNextHopNICAddress 1.3.6.1.4.1.89.12.6.1.1.7
The NIC address of the next hop.
OBJECT-TYPE    
  PhysAddress  

ipxDestNextHopNetNum 1.3.6.1.4.1.89.12.6.1.1.8
The IPX network number of the next hop.
OBJECT-TYPE    
  NetNumber  

ipxDestExistState 1.3.6.1.4.1.89.12.6.1.1.9
The validity of this entry. An entry with this value set to off may be deleted from the table at the IPX implementation's discretion.
OBJECT-TYPE    
  INTEGER off(1), on(2)  

ipxServices 1.3.6.1.4.1.89.12.7
OBJECT IDENTIFIER    

ipxServTable 1.3.6.1.4.1.89.12.7.1
The table of services, indexed by name and type.
OBJECT-TYPE    
  SEQUENCE OF  
    IpxServEntry

ipxServEntry 1.3.6.1.4.1.89.12.7.1.1
Each entry corresponds to one service.
OBJECT-TYPE    
  IpxServEntry  

ipxServSysInstance 1.3.6.1.4.1.89.12.7.1.1.1
The unique identifier of the instance of IPX to which this entry corresponds.
OBJECT-TYPE    
  INTEGER  

ipxServType 1.3.6.1.4.1.89.12.7.1.1.2
The service type.
OBJECT-TYPE    
  OCTET STRING Size(2)  

ipxServName 1.3.6.1.4.1.89.12.7.1.1.3
The service name.
OBJECT-TYPE    
  OCTET STRING Size(1..48)  

ipxServProtocol 1.3.6.1.4.1.89.12.7.1.1.4
The protocol from which knowledge of this service was obtained.
OBJECT-TYPE    
  INTEGER other(1), local(2), nlsp(4), static(5), sap(6)  

ipxServNetNum 1.3.6.1.4.1.89.12.7.1.1.5
The IPX network number portion of the IPX address of the service.
OBJECT-TYPE    
  NetNumber  

ipxServNode 1.3.6.1.4.1.89.12.7.1.1.6
The node portion of the IPX address of the service.
OBJECT-TYPE    
  OCTET STRING Size(6)  

ipxServSocket 1.3.6.1.4.1.89.12.7.1.1.7
The socket portion of the IPX address of the service.
OBJECT-TYPE    
  OCTET STRING Size(2)  

ipxServHopCount 1.3.6.1.4.1.89.12.7.1.1.8
The number of hops to the service.
OBJECT-TYPE    
  INTEGER  

ipxServExistState 1.3.6.1.4.1.89.12.7.1.1.9
The validity of this entry. An entry with this value set to off may be deleted from the table at the IPX implementation's discretion.
OBJECT-TYPE    
  INTEGER off(1), on(2)  

ripsap 1.3.6.1.4.1.89.12.8
OBJECT IDENTIFIER    

ripsapSystem 1.3.6.1.4.1.89.12.8.1
OBJECT IDENTIFIER    

ripSysTable 1.3.6.1.4.1.89.12.8.1.1
The RIP system table.
OBJECT-TYPE    
  SEQUENCE OF  
    RipSysEntry

ripSysEntry 1.3.6.1.4.1.89.12.8.1.1.1
Each entry corresponds to one instance of RIP running on the system.
OBJECT-TYPE    
  RipSysEntry  

ripSysInstance 1.3.6.1.4.1.89.12.8.1.1.1.1
The unique identifier of the instance of RIP to which this row corresponds. This value links the instance of RIP to an instance of IPX running on the system (i.e. the value of ripSysInstance should be the same as a value of ipxSysInstance). This value may be written only when creating a new entry in the table.
OBJECT-TYPE    
  INTEGER  

ripSysState 1.3.6.1.4.1.89.12.8.1.1.1.2
Indicates the operational state of this instance of RIP.
OBJECT-TYPE    
  INTEGER off(1), on(2)  

ripSysIncorrectPackets 1.3.6.1.4.1.89.12.8.1.1.1.3
The number of times that an incorrectly formatted RIP packet was received.
OBJECT-TYPE    
  Counter  

sapSysTable 1.3.6.1.4.1.89.12.8.1.2
The SAP system table.
OBJECT-TYPE    
  SEQUENCE OF  
    SapSysEntry

sapSysEntry 1.3.6.1.4.1.89.12.8.1.2.1
Each entry corresponds to one instance of SAP running on the system.
OBJECT-TYPE    
  SapSysEntry  

sapSysInstance 1.3.6.1.4.1.89.12.8.1.2.1.1
The unique identifier of the instance of SAP to which this row corresponds. This value links the instance of SAP to an instance of IPX running on the system (i.e. the value of SApSysInstance should be the same as a value of ipxSysInstance). This value may be written only when creating a new entry in the table.
OBJECT-TYPE    
  INTEGER  

sapSysState 1.3.6.1.4.1.89.12.8.1.2.1.2
Indicates the operational state of this instance of SAP.
OBJECT-TYPE    
  INTEGER off(1), on(2)  

sapSysIncorrectPackets 1.3.6.1.4.1.89.12.8.1.2.1.3
The number of times that an incorrectly formatted SAP packet was received.
OBJECT-TYPE    
  Counter  

ripsapCircuit 1.3.6.1.4.1.89.12.8.2
OBJECT IDENTIFIER    

ripCircTable 1.3.6.1.4.1.89.12.8.2.1
The RIP Circuit table.
OBJECT-TYPE    
  SEQUENCE OF  
    RipCircEntry

ripCircEntry 1.3.6.1.4.1.89.12.8.2.1.1
Each entry corresponds to one circuit known to the system.
OBJECT-TYPE    
  RipCircEntry  

ripCircSysInstance 1.3.6.1.4.1.89.12.8.2.1.1.1
The unique identifier of the instance of RIP and IPX (via ipxSysInstance) to which this entry corresponds. This value may be written only when creating a new entry in the table.
OBJECT-TYPE    
  INTEGER  

ripCircIndex 1.3.6.1.4.1.89.12.8.2.1.1.2
The identifier of this circuit, unique within the instance of RIP. This value corresponds to the circuit identifier found in ipxCircIndex. This value may be written only when creating a new entry in the table.
OBJECT-TYPE    
  INTEGER  

ripCircState 1.3.6.1.4.1.89.12.8.2.1.1.3
Indicates whether RIP information may be sent/received over this circuit.
OBJECT-TYPE    
  INTEGER off(1), on(2)  

ripCircUpdate 1.3.6.1.4.1.89.12.8.2.1.1.4
The RIP periodic update interval, in seconds.
OBJECT-TYPE    
  INTEGER  

ripCircAgeMultiplier 1.3.6.1.4.1.89.12.8.2.1.1.5
The holding multiplier for information received in RIP periodic updates.
OBJECT-TYPE    
  INTEGER  

ripCircOutPackets 1.3.6.1.4.1.89.12.8.2.1.1.6
The number of RIP packets sent on this circuit.
OBJECT-TYPE    
  Counter  

ripCircInPackets 1.3.6.1.4.1.89.12.8.2.1.1.7
The number of RIP packets received on this circuit.
OBJECT-TYPE    
  Counter  

sapCircTable 1.3.6.1.4.1.89.12.8.2.2
The SAP Circuit table.
OBJECT-TYPE    
  SEQUENCE OF  
    SapCircEntry

sapCircEntry 1.3.6.1.4.1.89.12.8.2.2.1
Each entry corresponds to one circuit known to the system.
OBJECT-TYPE    
  SapCircEntry  

sapCircSysInstance 1.3.6.1.4.1.89.12.8.2.2.1.1
The unique identifier of the instance of SAP and IPX (via ipxSysInstance) to which this entry corresponds. This value may be written only when creating a new entry in the table.
OBJECT-TYPE    
  INTEGER  

sapCircIndex 1.3.6.1.4.1.89.12.8.2.2.1.2
The identifier of this circuit, unique within the instance of SAP. This value corresponds to the circuit identifier found in ipxCircIndex. This value may be written only when creating a new entry in the table.
OBJECT-TYPE    
  INTEGER  

sapCircState 1.3.6.1.4.1.89.12.8.2.2.1.3
Indicates whether SAP information may be sent/received over this circuit.
OBJECT-TYPE    
  INTEGER off(1), on(2)  

sapCircUpdate 1.3.6.1.4.1.89.12.8.2.2.1.4
The SAP periodic update interval, in seconds.
OBJECT-TYPE    
  INTEGER  

sapCircAgeMultiplier 1.3.6.1.4.1.89.12.8.2.2.1.5
The holding multiplier for information received in SAP periodic updates.
OBJECT-TYPE    
  INTEGER  

sapCircGetNearestServerReply 1.3.6.1.4.1.89.12.8.2.2.1.6
Indicates whether to respond to SAP get nearest server requests received on this circuit.
OBJECT-TYPE    
  INTEGER no(1), yes(2)  

sapCircOutPackets 1.3.6.1.4.1.89.12.8.2.2.1.7
The number of SAP packets sent on this circuit.
OBJECT-TYPE    
  Counter  

sapCircInPackets 1.3.6.1.4.1.89.12.8.2.2.1.8
The number of SAP packets received on this circuit.
OBJECT-TYPE    
  Counter  

rndFACS 1.3.6.1.4.1.89.16
OBJECT IDENTIFIER    

rndFACSDefaultAction 1.3.6.1.4.1.89.16.1
Used to define the default action for the device, when no FACS statements applicable to a given frame are defined.
OBJECT-TYPE    
  INTEGER block(1), forward(2), enable(3), disable(4), blockAndReport(129)  

rndFACSActTable 1.3.6.1.4.1.89.16.2
The table of FACS action.
OBJECT-TYPE    
  SEQUENCE OF  
    RndFACSActEntry

rndFACSActEntry 1.3.6.1.4.1.89.16.2.1
Each rndFACSActEntry consist of the following parameters
OBJECT-TYPE    
  RndFACSActEntry  

rndFACSActType 1.3.6.1.4.1.89.16.2.1.1
This parameter indicate on which FACS Table the FACS action will preform.
OBJECT-TYPE    
  INTEGER tx(1), rx(2), activeDB(4), tempDB(5)  

rndFACSActIfIndex 1.3.6.1.4.1.89.16.2.1.2
The interface to which this FACS entry is applicable.
OBJECT-TYPE    
  INTEGER  

rndFACSAction 1.3.6.1.4.1.89.16.2.1.3
The management station that sends a SET request for one of these actions with indexes rndFACSType and rndFACSIfIndex defines the type and the interface Id for which all FACS statements are to be erased. If no interface or no type is specified, all FACS statements for a protocol are erased.
OBJECT-TYPE    
  INTEGER none(1), eraseIP(2), eraseDECnet(3), eraseIPX(4), eraseBrg(5), replaceIP(6), replaceIPX(8), replaceBrg(9), backupIP(10), backupIPX(12), backupBrg(13)  

rndFACSTable 1.3.6.1.4.1.89.16.3
The table of FACS statment.
OBJECT-TYPE    
  SEQUENCE OF  
    RndFACSEntry

rndFACSEntry 1.3.6.1.4.1.89.16.3.1
Each FACS statment consist of the following parameters
OBJECT-TYPE    
  RndFACSEntry  

rndFACSIfIndex 1.3.6.1.4.1.89.16.3.1.1
The interface to which this FACS entry is applicable.
OBJECT-TYPE    
  INTEGER  

rndFACSProtocolType 1.3.6.1.4.1.89.16.3.1.2
This parameter define the protocol the Security Access Control is applicable.
OBJECT-TYPE    
  INTEGER ip(1), ipx(2), dec(3), bridge(4)  

rndFACSType 1.3.6.1.4.1.89.16.3.1.3
The Mode of in which this FACS statement operates.
OBJECT-TYPE    
  INTEGER tx(1), rx(2), cod(3), activeDB(4), tempDB(5)  

rndFACSIndex 1.3.6.1.4.1.89.16.3.1.4
Index to the FACS Table.
OBJECT-TYPE    
  INTEGER  

rndFACSSrcAdd 1.3.6.1.4.1.89.16.3.1.5
The size of the octet string will be according to the protocol type define in rndFACSProtocolType.
OBJECT-TYPE    
  OCTET STRING  

rndFACSSrcAddMask 1.3.6.1.4.1.89.16.3.1.6
Source-address mask .
OBJECT-TYPE    
  OCTET STRING  

rndFACSDesAdd 1.3.6.1.4.1.89.16.3.1.7
Destination-address The size of the octet string will be according to the protocol type define in rndFACSProtocolType .
OBJECT-TYPE    
  OCTET STRING  

rndFACSDesAddMask 1.3.6.1.4.1.89.16.3.1.8
Destination-address mask .
OBJECT-TYPE    
  OCTET STRING  

rndFACSOperation 1.3.6.1.4.1.89.16.3.1.9
... .
OBJECT-TYPE    
  INTEGER block(1), forward(2), permit(3), deny(4), blockZHRP(5), blockAndReport(129)  

rndFACSNetFiltering 1.3.6.1.4.1.89.16.3.1.10
... .
OBJECT-TYPE    
  INTEGER none(1), l2multicast(2), arp(3), icmp(4), ip(5), udp(6), tcp(7), decnet(8), ipx(9)  

rndFACSSoketNum 1.3.6.1.4.1.89.16.3.1.11
Port/socket number for different applications 0 is default meaning not applicable.
OBJECT-TYPE    
  INTEGER  

rndFACSMask1Id 1.3.6.1.4.1.89.16.3.1.12
Index into RND mask table FACS/COD Type) .
OBJECT-TYPE    
  INTEGER  

rndFACSMask2Id 1.3.6.1.4.1.89.16.3.1.13
Index into RND mask table FACS/COD according to the value of rndFACSType .
OBJECT-TYPE    
  INTEGER  

rndFACSStatus 1.3.6.1.4.1.89.16.3.1.14
The status of a table entry.
OBJECT-TYPE    
  INTEGER valid(1), createRequest(2), underCreation(3), invalid(4)  

rndBootP 1.3.6.1.4.1.89.24
OBJECT IDENTIFIER    

rndBootPServerAddress 1.3.6.1.4.1.89.24.1
The IPAddress of the BOOTP server. the OpenGate will act as a BootP relay if this parameter is not equale to 0.0.0.0.
OBJECT-TYPE    
  IpAddress  

rndBootPRelaySecThreshold 1.3.6.1.4.1.89.24.2
BootP requests are relayed only if their SEC field is greater or equal to the threshold value in order to allow local BootP Servers to answer first.
OBJECT-TYPE    
  INTEGER  

ipSpec 1.3.6.1.4.1.89.26
OBJECT IDENTIFIER    

rsIpAddrTable 1.3.6.1.4.1.89.26.1
This table is parralel to MIB II IpAddrTable, and is used to add/delete entries to/from that table. In addition it contains private objects.
OBJECT-TYPE    
  SEQUENCE OF  
    RsIpAddrEntry

rsIpAddrEntry 1.3.6.1.4.1.89.26.1.1
The addressing information for one of this entity's IP addresses.
OBJECT-TYPE    
  RsIpAddrEntry  

rsIpAdEntAddr 1.3.6.1.4.1.89.26.1.1.1
The IP address to which this entry's addressing information pertains.
OBJECT-TYPE    
  IpAddress  

rsIpAdEntIfIndex 1.3.6.1.4.1.89.26.1.1.2
The index value which uniquely identifies the interface to which this entry is applicable. The interface identified by a particular value of this index is the same interface as identified by the same value of ifIndex.
OBJECT-TYPE    
  INTEGER  

rsIpAdEntNetMask 1.3.6.1.4.1.89.26.1.1.3
The subnet mask associated with the IP address of this entry. The value of the mask is an IP address with all the network bits set to 1 and all the hosts bits set to 0.
OBJECT-TYPE    
  IpAddress  

rsIpAdEntForwardIpBroadcast 1.3.6.1.4.1.89.26.1.1.4
This variable controls forwarding of IP (sub)net-directed broadcasts destined for an attached sub(net).
OBJECT-TYPE    
  INTEGER enable(1), disable(2)  

rsIpAdEntBackupAddr 1.3.6.1.4.1.89.26.1.1.5
OBJECT-TYPE    
  IpAddress  

rsIpAdEntStatus 1.3.6.1.4.1.89.26.1.1.6
The validity of this entry. Invalid indicates that this entry is invalid in IpAddrTable (MIB II).
OBJECT-TYPE    
  INTEGER valid(1), invalid(2)  

rsIpAdEntBcastAddr 1.3.6.1.4.1.89.26.1.1.7
Indicates how the host part of ip subnet broadcast messages will be filled: 0 - host part will be filled by 0 1 - host part will be filled by 1.
OBJECT-TYPE    
  INTEGER 0..1  

icmpSpec 1.3.6.1.4.1.89.26.2
OBJECT IDENTIFIER    

rsIcmpGenErrMsgEnable 1.3.6.1.4.1.89.26.2.1
This variable controlls the ability to generate ICMP error messages
OBJECT-TYPE    
  INTEGER enable(1), disable(2)  

rsIcmpRdTable 1.3.6.1.4.1.89.26.2.2
This table contains ICMP Router Discovery parameters configurated per IP interface.
OBJECT-TYPE    
  SEQUENCE OF  
    RsIcmpRdEntry

rsIcmpRdEntry 1.3.6.1.4.1.89.26.2.2.1
The ICMP parameters configurated for IP interface.
OBJECT-TYPE    
  RsIcmpRdEntry  

rsIcmpRdIpAddr 1.3.6.1.4.1.89.26.2.2.1.1
The IP address to which this entry's information pertains.
OBJECT-TYPE    
  IpAddress  

rsIcmpRdIpAdvertAddr 1.3.6.1.4.1.89.26.2.2.1.2
The IP destination address to be used for multicast Router Advertisements sent from the interface. The only permissible values are the all-systems multicast address, 224.0.0.1, or the limited-broadcast address, 255.255.255.255.
OBJECT-TYPE    
  IpAddress  

rsIcmpRdMaxAdvertInterval 1.3.6.1.4.1.89.26.2.2.1.3
The maximum time allowed between sending multicast Router Advertisements from the interface, in seconds. Must be no less than 4 seconds and no greater than 1800 seconds.
OBJECT-TYPE    
  INTEGER 4..1800  

rsIcmpRdMinAdvertInterval 1.3.6.1.4.1.89.26.2.2.1.4
The minimum time allowed between sending unsolicited multicast Router Advertisements from the interface, in seconds. Must be no less than 3 seconds and no greater than rsIcmpRdMaxAdvertInterval. Default: 0.75 * rsIcmpRdMaxAdvertInterval.
OBJECT-TYPE    
  INTEGER 3..1800  

rsIcmpRdAdvertLifetime 1.3.6.1.4.1.89.26.2.2.1.5
The maximum length of time that the advertised addresses are to be considered as valid. Must be no less than rsIcmpRdMaxAdvertInterval and no greater than 9000 seconds. Default: 3 * rsIcmpRdMaxAdvertInterval.
OBJECT-TYPE    
  INTEGER 4..9000  

rsIcmpRdAdvertise 1.3.6.1.4.1.89.26.2.2.1.6
A flag indicating whether or not the address is to be advertised.
OBJECT-TYPE    
  INTEGER enable(1), disable(2)  

rsIcmpRdPreferenceLevel 1.3.6.1.4.1.89.26.2.2.1.7
The preferability of the address as a default router address, relative to other router addresses on the same subnet.
OBJECT-TYPE    
  INTEGER  

rsIcmpRdEntStatus 1.3.6.1.4.1.89.26.2.2.1.8
Setting of any value to this object set values of all fields to the default values.
OBJECT-TYPE    
  INTEGER  

rip2Spec 1.3.6.1.4.1.89.26.3
OBJECT IDENTIFIER    

rsRip2IfConfTable 1.3.6.1.4.1.89.26.3.1
This table is extension of rip2IfConfTable (RFC 1389 ,RIP 2)
OBJECT-TYPE    
  SEQUENCE OF  
    RsRip2IfConfEntry

rsRip2IfConfEntry 1.3.6.1.4.1.89.26.3.1.1
OBJECT-TYPE    
  RsRip2IfConfEntry  

rsRip2IfConfAddress 1.3.6.1.4.1.89.26.3.1.1.1
The IP Address of this system on the indicated subnet.
OBJECT-TYPE    
  IpAddress  

rsRip2IfConfVirtualDis 1.3.6.1.4.1.89.26.3.1.1.2
This variable defines the virtual number of hops assigned to the interface specified by rsIfIpAddrIndex. This enables fine-tuning of the RIP routing algorithm.
OBJECT-TYPE    
  INTEGER  

rsRip2IfConfAutoSend 1.3.6.1.4.1.89.26.3.1.1.3
This variable controls RIP automatic send behavior. If enabled and no routers were heard on the interface, RIP will only send default route with high metric. Otherwise RIP will send updates according to configuration.
OBJECT-TYPE    
  INTEGER enable(1), disable(2)  

arpSpec 1.3.6.1.4.1.89.26.4
OBJECT IDENTIFIER    

rsArpDeleteTable 1.3.6.1.4.1.89.26.4.1
Setting this object to any not-null value has the effect of deleting all entries of the ARP table.
OBJECT-TYPE    
  INTEGER  

rsArpInactiveTimeOut 1.3.6.1.4.1.89.26.4.2
This variable defines the maximum time period (in second) that can pass between ARP requests concerning an entry in the ARP table. After this time period, the entry is deleted from the table.
OBJECT-TYPE    
  INTEGER  

rsArpProxy 1.3.6.1.4.1.89.26.4.3
When ARP Proxy is enabled, the router can respond to ARP requests for nodes located on a different sub-net, provided they are it its network table. The router responds with its own MAC address. When ARP Proxy is disabled, the router responds only to ARP requests for its own IP addresses.
OBJECT-TYPE    
  INTEGER enable(1), disable(2)  

tftp 1.3.6.1.4.1.89.26.5
OBJECT IDENTIFIER    

rsTftpRetryTimeOut 1.3.6.1.4.1.89.26.5.1
General Retransmission time-out value (seconds)
OBJECT-TYPE    
  INTEGER  

rsTftpTotalTimeOut 1.3.6.1.4.1.89.26.5.2
Total Retransmission time-out value (seconds)
OBJECT-TYPE    
  INTEGER  

rsSendConfigFile 1.3.6.1.4.1.89.26.5.3
The file name include path where the Router Server will put the full configuration. The default destination address will be the sender address.
OBJECT-TYPE    
  DisplayString  

rsGetConfigFile 1.3.6.1.4.1.89.26.5.4
The file name include path where the Router Server will get the configuration. The default source address will be the sender address.
OBJECT-TYPE    
  DisplayString  

rsLoadSoftware 1.3.6.1.4.1.89.26.5.5
The file name include path where the Router Server will get the software. The source address will the sender address.
OBJECT-TYPE    
  DisplayString  

rsFileServerAddress 1.3.6.1.4.1.89.26.5.6
The IP address of the configuration / sw server.
OBJECT-TYPE    
  IpAddress  

ipRedundancy 1.3.6.1.4.1.89.26.6
OBJECT IDENTIFIER    

ipRedundAdminStatus 1.3.6.1.4.1.89.26.6.1
This parameter controle the IP Redundancy in the device. In case the the parameter in Enable and second router down. all the traffic hendle by this element.
OBJECT-TYPE    
  INTEGER enable(1), disable(2)  

ipRedundOperStatus 1.3.6.1.4.1.89.26.6.2
obsolete
OBJECT-TYPE    
  INTEGER active(1), inactive(2)  

ipRedundRoutersTable 1.3.6.1.4.1.89.26.6.3
List of IP addresses backed up by this router.
OBJECT-TYPE    
  SEQUENCE OF  
    IpRedundRoutersEntry

ipRedundRoutersEntry 1.3.6.1.4.1.89.26.6.3.1
The row definition for this table.
OBJECT-TYPE    
  IpRedundRoutersEntry  

ipRedundRoutersIfAddr 1.3.6.1.4.1.89.26.6.3.1.1
The Ip address of the IP interface on which the redundancy feature is operational.
OBJECT-TYPE    
  IpAddress  

ipRedundRoutersMainRouterAddr 1.3.6.1.4.1.89.26.6.3.1.2
The Ip address of the polled main router.
OBJECT-TYPE    
  IpAddress  

ipRedundRoutersOperStatus 1.3.6.1.4.1.89.26.6.3.1.3
If active, the main router is considered inoperational and the IP interface operates as its backup.
OBJECT-TYPE    
  INTEGER active(1), inactive(2)  

ipRedundRoutersPollInterval 1.3.6.1.4.1.89.26.6.3.1.4
Polling interval for this router (in seconds). If 0 the router is not polled.
OBJECT-TYPE    
  INTEGER  

ipRedundRoutersTimeout 1.3.6.1.4.1.89.26.6.3.1.5
Interval in seconds during which the backed-up router must signal. If it does not signal, it is considered inoperational and the IP interface starts operating as backup.
OBJECT-TYPE    
  INTEGER  

ipRedundRoutersStatus 1.3.6.1.4.1.89.26.6.3.1.6
Entry status
OBJECT-TYPE    
  INTEGER active(1), notInService(2), notReady(3), createAndGo(4), createAndWait(5), destroy(6)  

ipRouteLeaking 1.3.6.1.4.1.89.26.7
OBJECT IDENTIFIER    

ipLeakStaticToRip 1.3.6.1.4.1.89.26.7.1
This parameter controls leaking (redistribution) of static routes to RIP. When enabled, all routes inserted to the IP routing table via SNMP are advertised into RIP.
OBJECT-TYPE    
  INTEGER enable(1), disable(2)  

ipLeakStaticToOspf 1.3.6.1.4.1.89.26.7.2
This parameter controls leaking (redistribution) of static routes into OSPF. When enabled, all routes inserted to the IP routing table via SNMP are advertised into OSPF as external routes.
OBJECT-TYPE    
  INTEGER enable(1), disable(2)  

ipLeakOspfToRip 1.3.6.1.4.1.89.26.7.3
This parameter controls leaking (redistribution) of routes from OSPF to RIP. If enabled, all routes learned via OSPF are advertised into RIP.
OBJECT-TYPE    
  INTEGER enable(1), disable(2)  

ipLeakRipToOspf 1.3.6.1.4.1.89.26.7.4
This parameter controls leaking (redistribution) of routes from RIP to OSPF. If enabled, all routes learned via RIP are advertised into OSPF as external routes.
OBJECT-TYPE    
  INTEGER enable(1), disable(2)  

ipLeakExtDirectToOspf 1.3.6.1.4.1.89.26.7.5
This parameter controls leaking (redistribution) into OSPF of direct routes external to OSPF, i.e. routes to local network corresponding to IP interfaces on which OSPF is disabled. When enabled, all such direct routes are advertised into OSPF as external routes.
OBJECT-TYPE    
  INTEGER enable(1), disable(2)  

ipRipFilter 1.3.6.1.4.1.89.26.8
OBJECT IDENTIFIER    

rsIpRipFilterGlbTable 1.3.6.1.4.1.89.26.8.1
The table of RIP global filters per IP router.
OBJECT-TYPE    
  SEQUENCE OF  
    RsIpRipFilterGlbEntry

rsIpRipFilterGlbEntry 1.3.6.1.4.1.89.26.8.1.1
An entry in the RIP global filter table
OBJECT-TYPE    
  RsIpRipFilterGlbEntry  

rsIpRipFilterGlbType 1.3.6.1.4.1.89.26.8.1.1.1
Type of filter - input/output
OBJECT-TYPE    
  INTEGER input(1), output(2)  

rsIpRipFilterGlbNumber 1.3.6.1.4.1.89.26.8.1.1.2
Number of RIP filter.
OBJECT-TYPE    
  INTEGER  

rsIpRipFilterGlbStatus 1.3.6.1.4.1.89.26.8.1.1.3
The validity of this entry. Setting this value to invalid deletes the entry, and the entry may be actualy removed from the table.
OBJECT-TYPE    
  INTEGER valid(1), invalid(2), underCreation(3)  

rsIpRipFilterGlbIpAddr 1.3.6.1.4.1.89.26.8.1.1.4
network prefix IP address, as in the forwarding table.
OBJECT-TYPE    
  IpAddress  

rsIpRipFilterGlbNetworkMaskBits 1.3.6.1.4.1.89.26.8.1.1.5
the number of bits in the IP Network mask, called network-prefix-length in Router Requirements terminology. for example: the value 16 means mask 255.255.0.0
OBJECT-TYPE    
  INTEGER  

rsIpRipFilterGlbMatchBits 1.3.6.1.4.1.89.26.8.1.1.6
the number of bits to match in the Network IP address. A value smaller than 32 defines a wildcard. for example: the value 8 means all routes whose leftmost 8 bits are equal to those of the network IP address. If this variable has a value other than 32, than rsIpRipFilterGlbNetworkMaskBits must be 0 and is ignored.
OBJECT-TYPE    
  INTEGER  

rsIpRipFilterGlbAction 1.3.6.1.4.1.89.26.8.1.1.7
Filter action - permit/deny for this network
OBJECT-TYPE    
  INTEGER deny(1), permit(2)  

rsIpRipFilterLclTable 1.3.6.1.4.1.89.26.8.2
Table of input/output RIP filters used per IP Interface.
OBJECT-TYPE    
  SEQUENCE OF  
    RsIpRipFilterLclEntry

rsIpRipFilterLclEntry 1.3.6.1.4.1.89.26.8.2.1
An entry in the Intf RIP filter table
OBJECT-TYPE    
  RsIpRipFilterLclEntry  

rsIpRipFilterLclIpIntf 1.3.6.1.4.1.89.26.8.2.1.1
The IP address identifying the RIP interface for this filter. This value corresponds to rsIpAdEntAddr.
OBJECT-TYPE    
  IpAddress  

rsIpRipFilterLclType 1.3.6.1.4.1.89.26.8.2.1.2
Type of filter - input/output
OBJECT-TYPE    
  INTEGER input(1), output(2)  

rsIpRipFilterLclNumber 1.3.6.1.4.1.89.26.8.2.1.3
Number of RIP filter for this Interface
OBJECT-TYPE    
  INTEGER  

rsIpRipFilterLclStatus 1.3.6.1.4.1.89.26.8.2.1.4
The validity of this entry. Setting this value to invalid deletes the entry, and the entry may be actualy removed from the table.
OBJECT-TYPE    
  INTEGER valid(1), invalid(2), underCreation(3)  

rsIpRipFilterLclIpAddr 1.3.6.1.4.1.89.26.8.2.1.5
network prefix IP address, as in the forwarding table.
OBJECT-TYPE    
  IpAddress  

rsIpRipFilterLclNetworkMaskBits 1.3.6.1.4.1.89.26.8.2.1.6
the number of bits in the IP Network mask, called network-prefix-length in Router Requirements terminology. for example: the value 16 means mask 255.255.0.0
OBJECT-TYPE    
  INTEGER  

rsIpRipFilterLclMatchBits 1.3.6.1.4.1.89.26.8.2.1.7
the number of bits to match in the Network IP address. A value smaller than 32 defines a wildcard. for example: the value 8 means all routes whose leftmost 8 bits are equal to those of the network IP address. If this variable has a value other than 32, than rsIpRipFilterLclNetworkMaskBits must be 0 and is ignored.
OBJECT-TYPE    
  INTEGER  

rsIpRipFilterLclAction 1.3.6.1.4.1.89.26.8.2.1.8
Filter action - permit/deny
OBJECT-TYPE    
  INTEGER deny(1), permit(2)  

rsRipEnable 1.3.6.1.4.1.89.26.9
Enables or disables RIP.
OBJECT-TYPE    
  INTEGER enable(1), disable(2)  

lreBoxAgentIP 1.3.6.1.4.1.89.26.10
Tok_String
OBJECT-TYPE    
  IpAddress  

virtualLan 1.3.6.1.4.1.89.27
OBJECT IDENTIFIER    

virtualLanTable 1.3.6.1.4.1.89.27.1
An entry of this table specifies an new ifIndex with a type of propVirtual(53).
OBJECT-TYPE    
  SEQUENCE OF  
    VirtualLanEntry

virtualLanEntry 1.3.6.1.4.1.89.27.1.1
A list of information for each virtual LAN.
OBJECT-TYPE    
  VirtualLanEntry  

vlIfIndex 1.3.6.1.4.1.89.27.1.1.1
An logical interface number, corresponded this VL
OBJECT-TYPE    
  INTEGER  

vlProto 1.3.6.1.4.1.89.27.1.1.2
The protocol, supported by this VL. The meanings of the values are: other: none of the following. This VL includes any protocol except the following protocols. It is a bridging VL. RS relies on a third-party router to exchange traffic between nodes on different virtual LANs of this type. IP: This is a routing VL, RS will route between nodes on different virtual LANs. IPmulticast: RS will broadcast the message to all the VL's ports. Used for video-conferencing applications. ipxRaw: This is a Routing VL, RS will route between nodes on different virtual LANs. ipxET: This is a routing VL, RS will route between nodes on different virtual LANs. ipxLLC: This is a routing VL, RS will route between nodes on different virtual LANs. ipxSNAP: This is a routing VL, RS will route between nodes on different virtual LANs. decNET: This is a bridging VL, RS relies on a third-party router to exchange traffic between nodes on different DECnet virtual LANs of this type. netBios: This is a Bridging VL, RS relies on a third-party router to exchange traffic between nodes on different NetBIOS virtual LANs of this type. appleTalk: This is a bridging VL, RS relies on a third-party router to exchange traffic between nodes on different AppleTalk virtual LANs of this type.
OBJECT-TYPE    
  INTEGER other(1), ip(2), ipmulticast(3), ipxRaw(4), ipxET(5), ipxLLC(6), ipxSNAP(7), decNET(8), decLAT(9), netBios(10), appleTalk(11), xns(12), sna(13), userDefined(14)  

vlAutoConfigEnable 1.3.6.1.4.1.89.27.1.1.3
It is used only in the case of IP. The meanings of the values are: true(1): Autolearning is used for this VL false(2): Autolearning isn't used for this VL from ports, specified in the table virtualLanAutoConfTable.
OBJECT-TYPE    
  TruthValue  

vlStatus 1.3.6.1.4.1.89.27.1.1.4
It is used to delete an entry
OBJECT-TYPE    
  RowStatus  

vlType 1.3.6.1.4.1.89.27.1.1.5
regular - ordinary type specBroadcast - for switches that support VLANs as a set of ports and only as a broadcast domain: broadcast frames do not cross VLAN's bounders, but unicast frames may be transmitted between different VLANs. Permits passing of broadcast frames between Vgate's VLANs. specArpReq - for switches that support VLANs as a set of ports and only as a broadcast domain: broadcast frames do not cross VLAN's bounders, but unicast frames may be transmitted between different VLANs. Permits passing of ARP request frames between Vgate's VLANs. specBroadcastAndUnicast - for switches that support VLANs as a set of ports but no frame crosses VLAN's bounders. Permits passing of IP/ARP request broadcast and IP unicast frames between Vgate's VLANs. specArpReqAndUnicast - for switches that support VLANs as a set of ports but no frame crosses VLAN's bounders. Permits passing of ARP request broadcast and IP unicast frames between Vgate's VLANs. This type can be used only for IP VLANs.
OBJECT-TYPE    
  INTEGER regular(1), specBroadcast(2), specArpReq(3), specBroadcastAndUnicast(4), specArpReqAndUnicast(5)  

virtualLanPortsTable 1.3.6.1.4.1.89.27.2
For each VL (a ifIndex with a type of propVirtual(53)) an entry of this table specifies a set of ports, which it contains.
OBJECT-TYPE    
  SEQUENCE OF  
    VirtualLanPortEntry

virtualLanPortEntry 1.3.6.1.4.1.89.27.2.1
A entry of this table specifies a VL and a port belonging to it
OBJECT-TYPE    
  VirtualLanPortEntry  

vLIfIndex 1.3.6.1.4.1.89.27.2.1.1
An logical interface number, corresponding to this VL
OBJECT-TYPE    
  INTEGER  

vLPortIfIndex 1.3.6.1.4.1.89.27.2.1.2
A physical port belonging to the VL specified by vlIfIndex.
OBJECT-TYPE    
  INTEGER  

vLPortType 1.3.6.1.4.1.89.27.2.1.3
static means configured by user dynamic means autoconfigured by the RS
OBJECT-TYPE    
  INTEGER static(1), dynamic(2)  

vLPortStatus 1.3.6.1.4.1.89.27.2.1.4
It is used to delete an entry
OBJECT-TYPE    
  RowStatus  

virtualLanAutoConfTable 1.3.6.1.4.1.89.27.3
This table specifies per a routing protocol a set of ports, from which RS will automatically learning VL in accordance with rules, defined by the protocol.
OBJECT-TYPE    
  SEQUENCE OF  
    VirtualLanAutoConfEntry

virtualLanAutoConfEntry 1.3.6.1.4.1.89.27.3.1
One port, specified by vlAutoConfPortIfIndex, for which the RS will automatically learn its VL in accordance with rules, defined by the protocol specified in vlAutoConfProto.
OBJECT-TYPE    
  VirtualLanAutoConfEntry  

vlAutoConfPortIfIndex 1.3.6.1.4.1.89.27.3.1.1
Port on which the autoconfig option should be supported
OBJECT-TYPE    
  INTEGER  

vlAutoConfProto 1.3.6.1.4.1.89.27.3.1.2
Protocol for which the autoconfig option is supported for the port specified by vlAutoConfPortIfIndex
OBJECT-TYPE    
  INTEGER ip(2)  

vlAutoConfStatus 1.3.6.1.4.1.89.27.3.1.3
It is used to delete an entry
OBJECT-TYPE    
  RowStatus  

virtualLanAutoConfAgingTimeout 1.3.6.1.4.1.89.27.4
The units of this MIB object is seconds. Its value can be either 0 or in range 10..65535 .
OBJECT-TYPE    
  INTEGER  

virtualLanProtocolVlan 1.3.6.1.4.1.89.27.5
OBJECT IDENTIFIER    

virtualLanUserEtherType 1.3.6.1.4.1.89.27.5.1
Tok_String
OBJECT-TYPE    
  OCTET STRING Size(2)  

virtualLanUserMask 1.3.6.1.4.1.89.27.5.2
Tok_String
OBJECT-TYPE    
  OCTET STRING Size(2)  

rsConf 1.3.6.1.4.1.89.28
OBJECT IDENTIFIER    

rsIfConfTable 1.3.6.1.4.1.89.28.1
This table enable the user to add interface to the RS. RS will automatically add the new interface to the interface Table
OBJECT-TYPE    
  SEQUENCE OF  
    RsIfConfEntry

rsIfConfEntry 1.3.6.1.4.1.89.28.1.1
Each entry defines a configured interface.
OBJECT-TYPE    
  RsIfConfEntry  

rsIfConfIndex 1.3.6.1.4.1.89.28.1.1.1
This variable uniquely identifies the interface. It is used as a cross reference in other system tables
OBJECT-TYPE    
  INTEGER  

rsIfConfType 1.3.6.1.4.1.89.28.1.1.2
This variable identifies the type of the specific entry in the rsIfConfTable. This field is writable only at creation time (i.e., when value of status is underCreation).
OBJECT-TYPE    
  RsIfType  

rsIfConfName 1.3.6.1.4.1.89.28.1.1.3
This variable provides a logical name to a specific entry in rsIfConfTable
OBJECT-TYPE    
  DisplayString  

rsIfConfStatus 1.3.6.1.4.1.89.28.1.1.4
The status of the ConfigEntry. The choices are those defined in SNMPv2-TC. Only: active, createAndWait, and destroy will be used. active - The conceptual row is available for use by the managed device. createAndWait - A new instance of a conceptual row is desired, but not to have it available for use by the managed device. destroy - Delete all instances associated with an existing conceptual row.
OBJECT-TYPE    
  RowStatus  

rsTunning 1.3.6.1.4.1.89.29
OBJECT IDENTIFIER    

rsHighPriority 1.3.6.1.4.1.89.29.1
This variable indicates the time interval the forwarding task inside the RS works in High Priority Mode.
OBJECT-TYPE    
  INTEGER  

rsLowPriority 1.3.6.1.4.1.89.29.2
This variable indicates the time interval the forwarding task inside the RS works in Low Priority Mode.
OBJECT-TYPE    
  INTEGER  

rsDbgLevel 1.3.6.1.4.1.89.29.3
This variable indicates the debug level the Router Server works. the range of this variable is 1..100
OBJECT-TYPE    
  INTEGER  

rsDiagnostic 1.3.6.1.4.1.89.29.4
This variable will contain some dignostic information in case on a problem ocurs in the RS functinality.
OBJECT-TYPE    
  DisplayString  

rsConfirmMessagTab 1.3.6.1.4.1.89.29.5
This variable enables the operator to confirm all the message in the event Message Table.
OBJECT-TYPE    
  INTEGER  

eventMessageTable 1.3.6.1.4.1.89.29.6
The Event Message table of the agent
OBJECT-TYPE    
  SEQUENCE OF  
    EventMessageEntry

eventMessageEntry 1.3.6.1.4.1.89.29.6.1
The row definition for this table.
OBJECT-TYPE    
  EventMessageEntry  

eventNum 1.3.6.1.4.1.89.29.6.1.1
The event number,the index of this table.
OBJECT-TYPE    
  INTEGER  

eventDesc 1.3.6.1.4.1.89.29.6.1.2
The event discription, this text will include time and severity.
OBJECT-TYPE    
  DisplayString  

reaTunning 1.3.6.1.4.1.89.29.7
OBJECT IDENTIFIER    

reaIpRemoteAgingTime 1.3.6.1.4.1.89.29.7.1
This variable specifies aging time used by the REA for remote entries in the Ip Fast Forwarding Table.
OBJECT-TYPE    
  INTEGER  

reaFftHashMaxChain 1.3.6.1.4.1.89.29.7.2
This variable specifies the maximum length of hash chains in the Fast Forwarding Tables.
OBJECT-TYPE    
  INTEGER  

reaMltcstBitOn 1.3.6.1.4.1.89.29.7.3
Tok_String
OBJECT-TYPE    
  INTEGER on(1), off(2)  

reaIpForwardEnable 1.3.6.1.4.1.89.29.7.4
The Platform will perform fast IP forwarding if only if this variable's value is enable.
OBJECT-TYPE    
  INTEGER enable(1), disable(2)  

reaIpxForwardEnable 1.3.6.1.4.1.89.29.7.5
The Platform will perform fast IPX forwarding if only if this variable's value is enable.
OBJECT-TYPE    
  INTEGER enable(1), disable(2)  

reaBridgeEnable 1.3.6.1.4.1.89.29.7.6
The Platform will perform bridging if only if this variable's value is enable.
OBJECT-TYPE    
  INTEGER enable(1), disable(2)  

reaFacsEnable 1.3.6.1.4.1.89.29.7.7
The RS and Platform will perform FASC if only if this variable's value is enable.
OBJECT-TYPE    
  INTEGER enable(1), disable(2)  

reaIpForwardDatagrams 1.3.6.1.4.1.89.29.7.8
The number of IP datagrams have been forwarded by the Platform.
OBJECT-TYPE    
  Counter  

reaIpInDiscards 1.3.6.1.4.1.89.29.7.9
The number of IP datagrams have been dicarded by the Platform.
OBJECT-TYPE    
  Counter  

reaIpxForwardDatagrams 1.3.6.1.4.1.89.29.7.10
The number of IPX datagrams have been forwarded by the Platform.
OBJECT-TYPE    
  Counter  

reaIpxInDiscards 1.3.6.1.4.1.89.29.7.11
The number of IP datagrams have been dicarded by the Platform.
OBJECT-TYPE    
  Counter  

reaBridgeFftTable 1.3.6.1.4.1.89.29.7.12
The Bridge Fast Forwarding Table
OBJECT-TYPE    
  SEQUENCE OF  
    ReaBridgeFftEntry

reaBridgeFftEntry 1.3.6.1.4.1.89.29.7.12.1
The row definition for this table.
OBJECT-TYPE    
  ReaBridgeFftEntry  

reaBrgFftEntryNum 1.3.6.1.4.1.89.29.7.12.1.1
Tok_String
OBJECT-TYPE    
  INTEGER  

reaBrgFftMacAddr 1.3.6.1.4.1.89.29.7.12.1.2
Tok_String
OBJECT-TYPE    
  PhysAddress  

reaBrgFftReNum 1.3.6.1.4.1.89.29.7.12.1.3
Tok_String
OBJECT-TYPE    
  INTEGER  

reaBrgFftPortNum 1.3.6.1.4.1.89.29.7.12.1.4
Tok_String
OBJECT-TYPE    
  INTEGER  

reaBrgFftFacsSrcIndex 1.3.6.1.4.1.89.29.7.12.1.5
Tok_String
OBJECT-TYPE    
  INTEGER  

reaBrgFftFacsDstIndex 1.3.6.1.4.1.89.29.7.12.1.6
Tok_String
OBJECT-TYPE    
  INTEGER  

reaBrgDiscards 1.3.6.1.4.1.89.29.7.13
The number of bridging datagrams have been discarded by the Platform.
OBJECT-TYPE    
  Counter  

reaBrgForwards 1.3.6.1.4.1.89.29.7.14
The number of bridging datagrams have been forwarded by the Platform.
OBJECT-TYPE    
  Counter  

reaIpFftTable 1.3.6.1.4.1.89.29.7.15
The IP Fast Forwarding Table
OBJECT-TYPE    
  SEQUENCE OF  
    ReaIpFftEntry

reaIpFftEntry 1.3.6.1.4.1.89.29.7.15.1
The row definition for this table.
OBJECT-TYPE    
  ReaIpFftEntry  

reaIpFftEntryNum 1.3.6.1.4.1.89.29.7.15.1.1
Tok_String
OBJECT-TYPE    
  INTEGER  

reaIpFftDstIpAddr 1.3.6.1.4.1.89.29.7.15.1.2
Tok_String
OBJECT-TYPE    
  IpAddress  

reaIpFftDstIpMask 1.3.6.1.4.1.89.29.7.15.1.3
Tok_String
OBJECT-TYPE    
  IpAddress  

reaIpFftRangeType 1.3.6.1.4.1.89.29.7.15.1.4
Tok_String
OBJECT-TYPE    
  INTEGER direct(1), remote(2)  

reaIpFftSrcMacAddr 1.3.6.1.4.1.89.29.7.15.1.5
Tok_String
OBJECT-TYPE    
  PhysAddress  

reaIpFftDstMacAddr 1.3.6.1.4.1.89.29.7.15.1.6
Tok_String
OBJECT-TYPE    
  PhysAddress  

reaIpFftReNum 1.3.6.1.4.1.89.29.7.15.1.7
Tok_String
OBJECT-TYPE    
  INTEGER  

reaIpFftPortNum 1.3.6.1.4.1.89.29.7.15.1.8
Tok_String
OBJECT-TYPE    
  INTEGER  

reaIpFftFacsSrcIndex 1.3.6.1.4.1.89.29.7.15.1.9
Tok_String
OBJECT-TYPE    
  INTEGER  

reaIpFftFacsDstIndex 1.3.6.1.4.1.89.29.7.15.1.10
Tok_String
OBJECT-TYPE    
  INTEGER  

reaIpFftApplFlags 1.3.6.1.4.1.89.29.7.15.1.11
A bit mask that defines the applications associated with this entry: __________________________________________ | Byte 1|Byte 2 |Byte 3 | ....|Byte 20 | |87654321| | 87654321| |________|_______________________________| Byte1 : bit1: Server Dispatcher Client
OBJECT-TYPE    
  OCTET STRING Size(4)  

reaIpxFftTable 1.3.6.1.4.1.89.29.7.16
The IPX Fast Forwarding Table
OBJECT-TYPE    
  SEQUENCE OF  
    ReaIpxFftEntry

reaIpxFftEntry 1.3.6.1.4.1.89.29.7.16.1
The row definition for this table.
OBJECT-TYPE    
  ReaIpxFftEntry  

reaIpxFftEntryNum 1.3.6.1.4.1.89.29.7.16.1.1
Tok_String
OBJECT-TYPE    
  INTEGER  

reaIpxFftDstNetid 1.3.6.1.4.1.89.29.7.16.1.2
Tok_String
OBJECT-TYPE    
  INTEGER  

reaIpxFftRangeType 1.3.6.1.4.1.89.29.7.16.1.3
Tok_String
OBJECT-TYPE    
  INTEGER direct(1), remote(2)  

reaIpxFftSrcMacAddr 1.3.6.1.4.1.89.29.7.16.1.4
Tok_String
OBJECT-TYPE    
  PhysAddress  

reaIpxFftDstMacAddr 1.3.6.1.4.1.89.29.7.16.1.5
Tok_String
OBJECT-TYPE    
  PhysAddress  

reaIpxFftReNum 1.3.6.1.4.1.89.29.7.16.1.6
Tok_String
OBJECT-TYPE    
  INTEGER  

reaIpxFftPortNum 1.3.6.1.4.1.89.29.7.16.1.7
Tok_String
OBJECT-TYPE    
  INTEGER  

reaIpxFftFacsSrcIndex 1.3.6.1.4.1.89.29.7.16.1.8
Tok_String
OBJECT-TYPE    
  INTEGER  

reaIpxFftFacsDstIndex 1.3.6.1.4.1.89.29.7.16.1.9
Tok_String
OBJECT-TYPE    
  INTEGER  

lreVnResposibilityTable 1.3.6.1.4.1.89.29.7.17
The Bridge Responsibility Table
OBJECT-TYPE    
  SEQUENCE OF  
    LreVnResposibilityEntry

lreVnResposibilityEntry 1.3.6.1.4.1.89.29.7.17.1
The row definition for this table.
OBJECT-TYPE    
  LreVnResposibilityEntry  

lreVnRespVn 1.3.6.1.4.1.89.29.7.17.1.1
Tok_String
OBJECT-TYPE    
  INTEGER  

lreVnRespStatus 1.3.6.1.4.1.89.29.7.17.1.2
Tok_String
OBJECT-TYPE    
  RowStatus  

reaSrcViolationEnable 1.3.6.1.4.1.89.29.7.18
The Platform will perform the Source Port Violation Procedure if only if this variable's value is enable.
OBJECT-TYPE    
  INTEGER enable(1), disable(2)  

reaSrcViolationTrapEnable 1.3.6.1.4.1.89.29.7.19
The RS will send the Source Port Violation TRAP messages if only if this variable's value is enable.
OBJECT-TYPE    
  INTEGER enable(1), disable(2)  

reaSrcAddrValidationEnable 1.3.6.1.4.1.89.29.7.20
The Platform will verify the source address of incoming IP datagram.
OBJECT-TYPE    
  INTEGER enable(1), disable(2)  

reaRsQueueDiscards 1.3.6.1.4.1.89.29.7.21
Tok_String
OBJECT-TYPE    
  Counter  

reaBufFree 1.3.6.1.4.1.89.29.7.22
The number of free buffers.
OBJECT-TYPE    
  INTEGER  

lreResetDstMacBit46 1.3.6.1.4.1.89.29.7.23
Tok_String
OBJECT-TYPE    
  INTEGER enable(1), disable(2)  

lreQueSourceSelect 1.3.6.1.4.1.89.29.7.24
Tok_String
OBJECT-TYPE    
  INTEGER vNET(1), dstMac(2)  

lreResetDstMacBit47 1.3.6.1.4.1.89.29.7.25
Tok_String
OBJECT-TYPE    
  INTEGER enable(1), disable(2)  

rsMaxEntriesTuning 1.3.6.1.4.1.89.29.8
OBJECT IDENTIFIER    

rsMaxBridgeForwardingEntriesTuning 1.3.6.1.4.1.89.29.8.1
OBJECT IDENTIFIER    

rsMaxBrgFrwEntries 1.3.6.1.4.1.89.29.8.1.1
Maximal number of entries in bridge forwarding table.
OBJECT-TYPE    
  INTEGER  

rsMaxBrgFrwEntriesAfterReset 1.3.6.1.4.1.89.29.8.1.2
Future maximal number of entries in bridge forwarding table.
OBJECT-TYPE    
  INTEGER  

rsMaxIpForwardingEntriesTuning 1.3.6.1.4.1.89.29.8.2
OBJECT IDENTIFIER    

rsMaxIpFrwEntries 1.3.6.1.4.1.89.29.8.2.1
Maximal number of entries in Ip forwarding table.
OBJECT-TYPE    
  INTEGER  

rsMaxIpFrwEntriesAfterReset 1.3.6.1.4.1.89.29.8.2.2
Future maximal number of entries in Ip forwarding table.
OBJECT-TYPE    
  INTEGER  

rsMaxArpEntriesTuning 1.3.6.1.4.1.89.29.8.3
OBJECT IDENTIFIER    

rsMaxArpEntries 1.3.6.1.4.1.89.29.8.3.1
Maximal number of entries in Arp forwarding table.
OBJECT-TYPE    
  INTEGER  

rsMaxArpEntriesAfterReset 1.3.6.1.4.1.89.29.8.3.2
Future maximal number of entries in Arp forwarding table.
OBJECT-TYPE    
  INTEGER  

rsMaxIpxForwardingEntriesTuning 1.3.6.1.4.1.89.29.8.4
OBJECT IDENTIFIER    

rsMaxIpxFrwEntries 1.3.6.1.4.1.89.29.8.4.1
Maximal number of entries in Ipx forwarding table.
OBJECT-TYPE    
  INTEGER  

rsMaxIpxFrwEntriesAfterReset 1.3.6.1.4.1.89.29.8.4.2
Future maximal number of entries in Ipx forwarding table.
OBJECT-TYPE    
  INTEGER  

rsMaxIpxSapEntriesTuning 1.3.6.1.4.1.89.29.8.5
OBJECT IDENTIFIER    

rsMaxIpxSapEntries 1.3.6.1.4.1.89.29.8.5.1
Maximal number of entries in IpxSap table.
OBJECT-TYPE    
  INTEGER  

rsMaxIpxSapEntriesAfterReset 1.3.6.1.4.1.89.29.8.5.2
Future maximal number of entries in IpxSap table.
OBJECT-TYPE    
  INTEGER  

rsMaxDspClntEntriesTuning 1.3.6.1.4.1.89.29.8.6
OBJECT IDENTIFIER    

rsMaxDspClntEntries 1.3.6.1.4.1.89.29.8.6.1
Maximal number of entries in rsSdClientsTable.
OBJECT-TYPE    
  INTEGER  

rsMaxDspClntEntriesAfterReset 1.3.6.1.4.1.89.29.8.6.2
Future maximal number of entries in rsSdClientsTable.
OBJECT-TYPE    
  INTEGER  

rsMaxZeroHopRoutEntriesTuning 1.3.6.1.4.1.89.29.8.7
OBJECT IDENTIFIER    

rsMaxZhrConns 1.3.6.1.4.1.89.29.8.7.1
The current maximal number of direct Zero-hop routing connections.
OBJECT-TYPE    
  INTEGER  

rsMaxZhrConnsAfterReset 1.3.6.1.4.1.89.29.8.7.2
The future (after reset) maximal number of direct Zero-hop routing connections.
OBJECT-TYPE    
  INTEGER  

rsMaxDspFrmEntriesTuning 1.3.6.1.4.1.89.29.8.8
OBJECT IDENTIFIER    

rsMaxDspFrmEntries 1.3.6.1.4.1.89.29.8.8.1
Maximal number of entries in rsSdClientsTable.
OBJECT-TYPE    
  INTEGER  

rsMaxDspFrmEntriesAfterReset 1.3.6.1.4.1.89.29.8.8.2
Future maximal number of entries in rsSdClientsTable.
OBJECT-TYPE    
  INTEGER  

rndApplications 1.3.6.1.4.1.89.35
OBJECT IDENTIFIER    

rsServerDispatcher 1.3.6.1.4.1.89.35.1
OBJECT IDENTIFIER    

rndMidLevelManagement 1.3.6.1.4.1.89.35.2
OBJECT IDENTIFIER    

rndAlarmOptions 1.3.6.1.4.1.89.35.2.2
OBJECT IDENTIFIER    

rndAlarmEnabling 1.3.6.1.4.1.89.35.2.2.1
Indicates whether alarms should be issued to the high-level NMS
OBJECT-TYPE    
  INTEGER enabled(1), disabled(2)  

rndAlarmInterval 1.3.6.1.4.1.89.35.2.2.2
Indicates the minimal period of time which must pass after issuing an alarm before issuing the same alarm again.
OBJECT-TYPE    
  INTEGER  

rndMonitoredElementsTable 1.3.6.1.4.1.89.35.2.3
The table of monitored elements of the network
OBJECT-TYPE    
  SEQUENCE OF  
    RndMonitoredElementEntry

rndMonitoredElementEntry 1.3.6.1.4.1.89.35.2.3.1
The row definition for this table.
OBJECT-TYPE    
  RndMonitoredElementEntry  

rndMonitoredElementAddress 1.3.6.1.4.1.89.35.2.3.1.1
The IP address of the monitored element
OBJECT-TYPE    
  IpAddress  

rndMonitoredElementCommunity 1.3.6.1.4.1.89.35.2.3.1.2
The community of the monitored element
OBJECT-TYPE    
  DisplayString Size(1..20)  

rndMonitoredElementLabel 1.3.6.1.4.1.89.35.2.3.1.3
The label assigned by the network manager to the monitored element
OBJECT-TYPE    
  DisplayString Size(1..20)  

rndDefaultPollingInterval 1.3.6.1.4.1.89.35.2.3.1.4
The default period of time between two consecutive pollings of the monitored element for the value of an object instance. If no other polling interval is specifically assigned to the monitored object instance, this one will be used
OBJECT-TYPE    
  INTEGER  

rndDefaultLogFile 1.3.6.1.4.1.89.35.2.3.1.5
The default file path of the log-file which will contain the polling results for the monitored element. If no other file path is specifically assigned to the monitored object instance, this log-file will be used.
OBJECT-TYPE    
  DisplayString  

rndMonitoredElementStatus 1.3.6.1.4.1.89.35.2.3.1.6
It is used to manage the monitored elements table and indicates the current monitoring status of an element.
OBJECT-TYPE    
  RowStatus  

rndMonitoringTable 1.3.6.1.4.1.89.35.2.4
The table of monitored object instances. Each monitored object instance belongs to a monitored element previously entered in the rndMonitoredElementsTable.
OBJECT-TYPE    
  SEQUENCE OF  
    RndMonitoringEntry

rndMonitoringEntry 1.3.6.1.4.1.89.35.2.4.1
The row definition for this table.
OBJECT-TYPE    
  RndMonitoringEntry  

rndMonitoredElement 1.3.6.1.4.1.89.35.2.4.1.1
A label assigned by the network manager to a monitored element to which this monitored object instance belongs. This label must have been previously entered in an instance of rndMonitoredElementLabel
OBJECT-TYPE    
  DisplayString Size(1..20)  

rndMonitoredObjectInstanceLabel 1.3.6.1.4.1.89.35.2.4.1.2
The label assigned by the network manager to the monitored object instance
OBJECT-TYPE    
  DisplayString Size(1..20)  

rndMonitoredObjectName 1.3.6.1.4.1.89.35.2.4.1.3
The symbolic object type name of the object to which the monitored object instance belongs (as it appears the MIB module definition). In case of ambiguity the : format should be used. An instance of rndMonitoredObjectName need not be assigned any value, if the corresponding instance of rndMonitoredObjectIdentifier is assigned a value, since any one of these, together with the object instance identifier, suffices to unambigously identify the monitored object instance.
OBJECT-TYPE    
  DisplayString Size(0..20)  

rndMonitoredObjectIdentifier 1.3.6.1.4.1.89.35.2.4.1.4
The object identifier of the object to which the monitored object instance belongs. An instance of rndMonitoredObjectIdentifier need not be assigned any value, if the corresponding instance of rndMonitoredObjectName is assigned a value, since any one of these, together with the object instance identifier, suffices to unambigously identify the monitored object instance.
OBJECT-TYPE    
  OBJECT IDENTIFIER  

rndMonitoredObjectInstance 1.3.6.1.4.1.89.35.2.4.1.5
The instance identifier (key) of the monitored object instance.
OBJECT-TYPE    
  OBJECT IDENTIFIER  

rndMonitoredObjectSyntax 1.3.6.1.4.1.89.35.2.4.1.6
The syntax of the monitored object instance (i.e., the syntax of the object type of the object to which the monitored instance belongs). Need not be assigned any value if the corresponding instance of rndMonitoredObjectName has been assigned a value
OBJECT-TYPE    
  INTEGER integer(1), octet-string(2), ip-address(3), object-identifier(4)  

rndMonitoringInterval 1.3.6.1.4.1.89.35.2.4.1.7
The period of time between two consecutive retrievals of the monitored object instance's value.
OBJECT-TYPE    
  INTEGER  

rndAlarmMaxTreshold 1.3.6.1.4.1.89.35.2.4.1.8
The value of the monitored object instance, the exceeding of which will cause the generation of an alarm to the high-level management station.
OBJECT-TYPE    
  INTEGER  

rndAlarmMinTreshold 1.3.6.1.4.1.89.35.2.4.1.9
If the value of the monitored object instance falls below the value assigned to rndAlarmMinTreshold, an alarm to the high-level management station will be issued.
OBJECT-TYPE    
  INTEGER  

rndMonitoringLogfile 1.3.6.1.4.1.89.35.2.4.1.10
The entire path of the file in which the results of the monitoring of this object instance should be recorded.
OBJECT-TYPE    
  DisplayString  

rndMonitoringEntryStatus 1.3.6.1.4.1.89.35.2.4.1.11
It is used to manage the monitored object instances table and indicates the current monitoring status of an object instance.
OBJECT-TYPE    
  RowStatus  

rndMibFilesTable 1.3.6.1.4.1.89.35.2.5
The table of monitored object instances. Each monitored object instance belongs to a monitored element previously entered in the rndMonitoredElementsTable.
OBJECT-TYPE    
  SEQUENCE OF  
    RndMibFileEntry

rndMibFileEntry 1.3.6.1.4.1.89.35.2.5.1
The row definition for this table.
OBJECT-TYPE    
  RndMibFileEntry  

rndMibFileIndex 1.3.6.1.4.1.89.35.2.5.1.1
The number of the MIB file in the list MIB files supported by the Mid-Level management station. The order of the MIB files in this list must reflect the the IMPORT relation between the MIBS contained in the MIB files, i.e., if MIB A IMPORTS FROM MIB B, the file containing MIB A must have a lesser index in this table than the file containing MIB B.
OBJECT-TYPE    
  INTEGER  

rndMibFilePath 1.3.6.1.4.1.89.35.2.5.1.2
The path of the MIB file in the MIB file server.
OBJECT-TYPE    
  DisplayString  

rndMibFileRefresh 1.3.6.1.4.1.89.35.2.5.1.3
Indicates if the file should be fetched after setting this entry from the MIB file server.
OBJECT-TYPE    
  INTEGER no(1), yes(2)  

rndMibFileEntryStatus 1.3.6.1.4.1.89.35.2.5.1.4
It is used to manage the MIB files table.
OBJECT-TYPE    
  RowStatus  

rndHardwareConfiguration 1.3.6.1.4.1.89.35.2.6
Indicates whether the current SET SNMP PDU contains hardware configuration (i.e., normally read-only variables). SET of such variables in the Mid-level management station will be allowed only if this variable is included in the SNMP PDU and its value is true. Its value as returned in a GET SNMP PDU will always be false.
OBJECT-TYPE    
  TruthValue  

rndEraseSimulatedConfiguration 1.3.6.1.4.1.89.35.2.7
eraseSimulatedConfiguration instructs the MLNMS to erase all the simulated configuration from its configuration data-base (CDB). This the only accepted value for SNMP SET statements and will never be returned in SNMP GET statements. simulatedConfigurationPresent indicates that the MLNMS currently has a simulated configuration. simulatedConfigurationErased indicates that the MLNMS currently has no simulated configuration.
OBJECT-TYPE    
  INTEGER eraseSimulatedConfiguration(1), simulatedConfigurationPresent(2), simulatedConfigurationErased(3)  

rndDeleteValuesTable 1.3.6.1.4.1.89.35.2.8
This table indicates which MIB variables are row status fields which control the status of the entry to which they belong. This table also indicates which (integer!) value of these MIB variables will cause, if present in a SNMP SET PDU, the deletion of the conceptual row instance to which the SET MIB variable instance belongs.
OBJECT-TYPE    
  SEQUENCE OF  
    RndDeleteValuesEntry

rndDeleteValuesEntry 1.3.6.1.4.1.89.35.2.8.1
The row definition for the rndDeleteValuesTable table.
OBJECT-TYPE    
  RndDeleteValuesEntry  

rndRowStatusVariableName 1.3.6.1.4.1.89.35.2.8.1.1
The name of the row status field. This name may not necessarily be any name which is present in the MIBs loaded into the MLNMS station.
OBJECT-TYPE    
  DisplayString Size(1..80)  

rndRowStatusObjectId 1.3.6.1.4.1.89.35.2.8.1.2
The object id of the row status field. If the rndRowStatusVariableName is a name present in the MIBs loaded into the MLNMS, this MIB variable is not required, but if given, it must match the object id known to the MLNMS. The variable identified by rndRowStatusVariableName and/or rndRowStatusObjectId must be a read-write MIB variable of type INTEGER which belongs to an entry (i.e, is a child of a MIB variable of type SEQUENCE).
OBJECT-TYPE    
  OBJECT IDENTIFIER  

rndRowDeleteValue 1.3.6.1.4.1.89.35.2.8.1.3
The value of the variable identified by rndRowStatusVariableName and/or rndRowStatusObjectId, which, if present in a SNMP SET PDU, will cause the deletion of the conceptual row instance which the SET MIB variable instance belongs.
OBJECT-TYPE    
  INTEGER  

rndDeleteValueEntryStatus 1.3.6.1.4.1.89.35.2.8.1.4
It is used to delete an entry from this table.
OBJECT-TYPE    
  RowStatus  

rsIpZeroHopRouting 1.3.6.1.4.1.89.35.3
OBJECT IDENTIFIER    

rsIpZhrGeneralStatus 1.3.6.1.4.1.89.35.3.1
This parameter enables or disables the IP Zero Hop Routing feature for all IP interfaces. The IP Zero Hop Routing feature can also be enabled or disabled on each IP interface through the rsIpZhrStatusTable.
OBJECT-TYPE    
  INTEGER enable(1), disable(2)  

rsIpZhrAgingTimeout 1.3.6.1.4.1.89.35.3.2
This parameter controls the aging time-out in seconds of direct connections which were allocated. The virtual IP address of a direct connection whose time-out has expired is eligible for allocation to a different connection.
OBJECT-TYPE    
  INTEGER  

rsIpZhrStatusTable 1.3.6.1.4.1.89.35.3.3
The administrative status of the ZHR feature per ip interface.
OBJECT-TYPE    
  SEQUENCE OF  
    RsIpZhrStatusEntry

rsIpZhrStatusEntry 1.3.6.1.4.1.89.35.3.3.1
An entry in the ZHR status table.
OBJECT-TYPE    
  RsIpZhrStatusEntry  

rsIpZhrStatusIpIntf 1.3.6.1.4.1.89.35.3.3.1.1
The Ip interface whose ZHR feature status is accessed.
OBJECT-TYPE    
  IpAddress  

rsIpZhrAdminStatus 1.3.6.1.4.1.89.35.3.3.1.2
It is used to control whether ZHR will operate on the interface.
OBJECT-TYPE    
  INTEGER enable(1), disable(2)  

rsIpZhrVirtAddressTable 1.3.6.1.4.1.89.35.3.4
The table of free virtual IP addresses which may be allocated to establish direct connections - Per IP Interface.
OBJECT-TYPE    
  SEQUENCE OF  
    RsIpZhrVirtAddressEntry

rsIpZhrVirtAddressEntry 1.3.6.1.4.1.89.35.3.4.1
An entry in the ZHR virtual IP addresses table
OBJECT-TYPE    
  RsIpZhrVirtAddressEntry  

rsIpZhrVirtAddressIpIntf 1.3.6.1.4.1.89.35.3.4.1.1
The Ip Interface to which the IP addresses in this entry are allocated.
OBJECT-TYPE    
  IpAddress  

rsIpZhrVirtAddressTo 1.3.6.1.4.1.89.35.3.4.1.2
The last free IP address in the block.
OBJECT-TYPE    
  IpAddress  

rsIpZhrVirtAddressFrom 1.3.6.1.4.1.89.35.3.4.1.3
The first free IP address in the block.
OBJECT-TYPE    
  IpAddress  

rsIpZhrVirtAddressStatus 1.3.6.1.4.1.89.35.3.4.1.4
It is used to manage the virtual address table. The supported actions will be active, createAndGo and destroy.
OBJECT-TYPE    
  RowStatus  

rsIpZhrConnectionsTable 1.3.6.1.4.1.89.35.3.5
Table of the currently active direct connections.
OBJECT-TYPE    
  SEQUENCE OF  
    RsIpZhrConnectionEntry

rsIpZhrConnectionEntry 1.3.6.1.4.1.89.35.3.5.1
An entry in the ZHR Connection table
OBJECT-TYPE    
  RsIpZhrConnectionEntry  

rsIpZhrConnectionIpIntf 1.3.6.1.4.1.89.35.3.5.1.1
The IP Interface for which this direct connection was established.
OBJECT-TYPE    
  IpAddress  

rsIpZhrConnectionSrcIp 1.3.6.1.4.1.89.35.3.5.1.2
The source IP Address of this direct connection.
OBJECT-TYPE    
  IpAddress  

rsIpZhrConnectionDestIp 1.3.6.1.4.1.89.35.3.5.1.3
The destination IP Address of this direct connection.
OBJECT-TYPE    
  IpAddress  

rsIpZhrConnectionVirtualIp 1.3.6.1.4.1.89.35.3.5.1.4
The virtual IP address allocated for this direct connection.
OBJECT-TYPE    
  IpAddress  

rsIpZhrConnectionType 1.3.6.1.4.1.89.35.3.5.1.5
The type of this direct connection. dynamic - established by the RS. disabled - established by the RS. The RS detected that the virtual address is already used as destination by the source BEFORE its allocation, and therefore marked this connection as 'disabled' to prevent a future allocation of this virtual address to this source. static - established by user.
OBJECT-TYPE    
  INTEGER static(1), dynamic(2), disabled(3)  

rsIpZhrConnectionAge 1.3.6.1.4.1.89.35.3.5.1.6
The age of the connection in seconds.
OBJECT-TYPE    
  INTEGER  

rsIpZhrConnectionStatus 1.3.6.1.4.1.89.35.3.5.1.7
It is used to manage the connections table. The supported actions will be active, createAndGo and destroy.
OBJECT-TYPE    
  RowStatus  

routeTableOverflow 5
An overflow condition has occurred in the Routing Table. The Routing Table is used for IP routing algorithm (RIP).
TRAP-TYPE    

resetRequired 10
This trap indicates that in order to perform the last SET request, a reset operation of the router/bridge is required. This occurs when the layer 2 routing algorithm is changed between SPF and Spanning Tree. The reset can be performed manually or using the variable rndAction.
TRAP-TYPE    

endTftp 12
This trap indicates that in the device finished a TFTP transaction with the management station. variable rndErrorDesc and rndErrorSeverity provides the actual message text and severity respectively.
TRAP-TYPE    

abortTftp 13
This trap indicates that in the device aborted a TFTP session with the management station. variable rndErrorDesc and rndErrorSeverity provides the actual message text and severity respectively.
TRAP-TYPE    

startTftp 14
Informational trap indicating that the device has intiated a TFTP session. rndErrorDesc will contain the file type in question
TRAP-TYPE    

ipxRipTblOverflow 36
This trap indicates that in an OpenGate IPX RIP table overflow. The bound variable rndErrorDesc, rndErrorSeverity provides the actual message text and severity respectively.
TRAP-TYPE    

ipxSapTblOverflow 37
This trap indicates that in an OpenGate IPX SAP table overflow. The bound variable rndErrorDesc, rndErrorSeverity provides the actual message text and severity respectively.
TRAP-TYPE    

facsAccessVoilation 49
This trap indicates that message that fits FACS statenebt with operation blockAndReport was forward to the interface.The bound variable rndErrorDesc, rndErrorSeverity(== info ) and interface Number.
TRAP-TYPE    

autoConfigurationCompleted 50
This trap indicates that auto comfiguration completetd succssefully. The bound variable rndErrorDesc, rndErrorSeverity(== info )
TRAP-TYPE    

forwardingTabOverflow 51
This trap indicates that an overflow condition has occurred in the layer II Forward Table. The bound variable rndErrorDesc, rndErrorSeverity(== warning )
TRAP-TYPE    

errorsDuringInit 61
Tok_String
TRAP-TYPE    

vlanDynPortAdded 66
Tok_String
TRAP-TYPE    

vlanDynPortRemoved 67
Tok_String
TRAP-TYPE    

rsSDclientsTableOverflow 68
This warning is generated when an overflow occurs in the clients table.
TRAP-TYPE    

rsSDinactiveServer 69
This warning is generated when a server does not respond to the dispatchers polling and is thought to be inactive.
TRAP-TYPE    

rsIpZhrConnectionsTableOverflow 70
The Zero Hop Routing connections Table has been overflown.
TRAP-TYPE    

rsIpZhrReqStaticConnNotAccepted 71
The requested static connection was not accepted because there is no available IP virtual address to allocate to it.
TRAP-TYPE    

rsIpZhrVirtualIpAsSource 72
The virtual IP address appeared as a source IP. All the connections using it will be deleted and it will not be further allocated to new connections.
TRAP-TYPE    

rsIpZhrNotAllocVirtualIp 73
The source IP address sent an ARP specifying a virtual IP which was not allocated for this source. This virtual IP will not be allocated to connections of this specific source IP.
TRAP-TYPE    

rsSnmpSetRequestInSpecialCfgState 74
An incoming SNMP SET request was rejected because no such requests (except action requests) are accepted after start of new configuration reception or during sending the current configuration to an NMS.
TRAP-TYPE    

rsWSDRedundancySwitch 141
Whenever main server fails and backup takes over or server comes up after failure a trap of this type is issued.
TRAP-TYPE