RITTAL-CMC-TC-MIB

File: RITTAL-CMC-TC-MIB.mib (153093 bytes)

Imported modules

RFC1155-SMI	RFC1213-MIB	RFC-1212
RFC-1215

Imported symbols

enterprises	DisplayString	sysName
sysDescr	sysContact	sysLocation
OBJECT-TYPE	TRAP-TYPE

Defined Types

CmcTcUnit1SensorEntry
SEQUENCE
	unit1SensorIndex	INTEGER
	unit1SensorType	INTEGER
	unit1SensorText	DisplayString
	unit1SensorStatus	INTEGER
	unit1SensorValue	INTEGER
	unit1SensorSetHigh	INTEGER
	unit1SensorSetLow	INTEGER
	unit1SensorSetWarn	INTEGER
	unit1SensorHysteresis	INTEGER
	unit1SensorDisplayFactor	INTEGER
	unit1SensorScaleStart	INTEGER
	unit1SensorScaleEnd	INTEGER
	unit1SensorUnit	DisplayString
	unit1SensorInfo	DisplayString

CmcTcUnit1OutputEntry
SEQUENCE
	unit1OutputIndex	INTEGER
	unit1OutputType	INTEGER
	unit1OutputText	DisplayString
	unit1OutputStatus	INTEGER
	unit1OutputValue	INTEGER
	unit1OutputSet	INTEGER
	unit1OutputConfig	INTEGER
	unit1OutputDelay	INTEGER
	unit1OutputTimeoutAction	INTEGER

CmcTcUnit1MsgEntry
SEQUENCE
	unit1MsgIndex	INTEGER
	unit1MsgText	DisplayString
	unit1MsgStatus	INTEGER
	unit1MsgRelay	INTEGER
	unit1MsgBeeper	INTEGER
	unit1MsgTrap1	INTEGER
	unit1MsgTrap2	INTEGER
	unit1MsgTrap3	INTEGER
	unit1MsgTrap4	INTEGER
	unit1MsgQuit	INTEGER
	unit1MsgDelay	INTEGER

CmcTcUnit2SensorEntry
SEQUENCE
	unit2SensorIndex	INTEGER
	unit2SensorType	INTEGER
	unit2SensorText	DisplayString
	unit2SensorStatus	INTEGER
	unit2SensorValue	INTEGER
	unit2SensorSetHigh	INTEGER
	unit2SensorSetLow	INTEGER
	unit2SensorSetWarn	INTEGER
	unit2SensorHysteresis	INTEGER
	unit2SensorDisplayFactor	INTEGER
	unit2SensorScaleStart	INTEGER
	unit2SensorScaleEnd	INTEGER
	unit2SensorUnit	DisplayString
	unit2SensorInfo	DisplayString

CmcTcUnit2OutputEntry
SEQUENCE
	unit2OutputIndex	INTEGER
	unit2OutputType	INTEGER
	unit2OutputText	DisplayString
	unit2OutputStatus	INTEGER
	unit2OutputValue	INTEGER
	unit2OutputSet	INTEGER
	unit2OutputConfig	INTEGER
	unit2OutputDelay	INTEGER
	unit2OutputTimeoutAction	INTEGER

CmcTcUnit2MsgEntry
SEQUENCE
	unit2MsgIndex	INTEGER
	unit2MsgText	DisplayString
	unit2MsgStatus	INTEGER
	unit2MsgRelay	INTEGER
	unit2MsgBeeper	INTEGER
	unit2MsgTrap1	INTEGER
	unit2MsgTrap2	INTEGER
	unit2MsgTrap3	INTEGER
	unit2MsgTrap4	INTEGER
	unit2MsgQuit	INTEGER
	unit2MsgDelay	INTEGER

CmcTcUnit3SensorEntry
SEQUENCE
	unit3SensorIndex	INTEGER
	unit3SensorType	INTEGER
	unit3SensorText	DisplayString
	unit3SensorStatus	INTEGER
	unit3SensorValue	INTEGER
	unit3SensorSetHigh	INTEGER
	unit3SensorSetLow	INTEGER
	unit3SensorSetWarn	INTEGER
	unit3SensorHysteresis	INTEGER
	unit3SensorDisplayFactor	INTEGER
	unit3SensorScaleStart	INTEGER
	unit3SensorScaleEnd	INTEGER
	unit3SensorUnit	DisplayString
	unit3SensorInfo	DisplayString

CmcTcUnit3OutputEntry
SEQUENCE
	unit3OutputIndex	INTEGER
	unit3OutputType	INTEGER
	unit3OutputText	DisplayString
	unit3OutputStatus	INTEGER
	unit3OutputValue	INTEGER
	unit3OutputSet	INTEGER
	unit3OutputConfig	INTEGER
	unit3OutputDelay	INTEGER
	unit3OutputTimeoutAction	INTEGER

CmcTcUnit3MsgEntry
SEQUENCE
	unit3MsgIndex	INTEGER
	unit3MsgText	DisplayString
	unit3MsgStatus	INTEGER
	unit3MsgRelay	INTEGER
	unit3MsgBeeper	INTEGER
	unit3MsgTrap1	INTEGER
	unit3MsgTrap2	INTEGER
	unit3MsgTrap3	INTEGER
	unit3MsgTrap4	INTEGER
	unit3MsgQuit	INTEGER
	unit3MsgDelay	INTEGER

CmcTcUnit4SensorEntry
SEQUENCE
	unit4SensorIndex	INTEGER
	unit4SensorType	INTEGER
	unit4SensorText	DisplayString
	unit4SensorStatus	INTEGER
	unit4SensorValue	INTEGER
	unit4SensorSetHigh	INTEGER
	unit4SensorSetLow	INTEGER
	unit4SensorSetWarn	INTEGER
	unit4SensorHysteresis	INTEGER
	unit4SensorDisplayFactor	INTEGER
	unit4SensorScaleStart	INTEGER
	unit4SensorScaleEnd	INTEGER
	unit4SensorUnit	DisplayString
	unit4SensorInfo	DisplayString

CmcTcUnit4OutputEntry
SEQUENCE
	unit4OutputIndex	INTEGER
	unit4OutputType	INTEGER
	unit4OutputText	DisplayString
	unit4OutputStatus	INTEGER
	unit4OutputValue	INTEGER
	unit4OutputSet	INTEGER
	unit4OutputConfig	INTEGER
	unit4OutputDelay	INTEGER
	unit4OutputTimeoutAction	INTEGER

CmcTcUnit4MsgEntry
SEQUENCE
	unit4MsgIndex	INTEGER
	unit4MsgText	DisplayString
	unit4MsgStatus	INTEGER
	unit4MsgRelay	INTEGER
	unit4MsgBeeper	INTEGER
	unit4MsgTrap1	INTEGER
	unit4MsgTrap2	INTEGER
	unit4MsgTrap3	INTEGER
	unit4MsgTrap4	INTEGER
	unit4MsgQuit	INTEGER
	unit4MsgDelay	INTEGER

CmcTcValuesEntry
SEQUENCE
	valuesIndex	INTEGER
	valuesText	DisplayString
	valuesStatus	INTEGER
	valuesValue	INTEGER
	valuesSetHigh	INTEGER
	valuesSetLow	INTEGER
	valuesHysteresis	INTEGER

CmcTcTimerEntry
SEQUENCE
	cmcTcTimerIndex	INTEGER
	cmcTcTimerStatus	INTEGER
	cmcTcTimerDayOfWeek	INTEGER
	cmcTcTimeOn	DisplayString
	cmcTcTimeOff	DisplayString
	cmcTcTimeControl	INTEGER
	cmcTcTimerFunction	INTEGER

CmcTcTrapTableEntry
SEQUENCE
	trapIndex	INTEGER
	trapStatus	INTEGER
	trapIPaddress	DisplayString

Defined Values

rittal		1.3.6.1.4.1.2606
OBJECT IDENTIFIER

cmcTc		1.3.6.1.4.1.2606.4
OBJECT IDENTIFIER

cmcTcMibRev		1.3.6.1.4.1.2606.4.1
OBJECT IDENTIFIER

cmcTcStatus		1.3.6.1.4.1.2606.4.2
OBJECT IDENTIFIER

cmcTcStatusSensorUnit1		1.3.6.1.4.1.2606.4.2.3
OBJECT IDENTIFIER

cmcTcStatusUnit1Sensors		1.3.6.1.4.1.2606.4.2.3.5
OBJECT IDENTIFIER

cmcTcStatusUnit1Outputs		1.3.6.1.4.1.2606.4.2.3.6
OBJECT IDENTIFIER

cmcTcStatusUnit1Msg		1.3.6.1.4.1.2606.4.2.3.7
OBJECT IDENTIFIER

cmcTcStatusSensorUnit2		1.3.6.1.4.1.2606.4.2.4
OBJECT IDENTIFIER

cmcTcStatusUnit2Sensors		1.3.6.1.4.1.2606.4.2.4.5
OBJECT IDENTIFIER

cmcTcStatusUnit2Outputs		1.3.6.1.4.1.2606.4.2.4.6
OBJECT IDENTIFIER

cmcTcStatusUnit2Msg		1.3.6.1.4.1.2606.4.2.4.7
OBJECT IDENTIFIER

cmcTcStatusSensorUnit3		1.3.6.1.4.1.2606.4.2.5
OBJECT IDENTIFIER

cmcTcStatusUnit3Sensors		1.3.6.1.4.1.2606.4.2.5.5
OBJECT IDENTIFIER

cmcTcStatusUnit3Outputs		1.3.6.1.4.1.2606.4.2.5.6
OBJECT IDENTIFIER

cmcTcStatusUnit3Msg		1.3.6.1.4.1.2606.4.2.5.7
OBJECT IDENTIFIER

cmcTcStatusSensorUnit4		1.3.6.1.4.1.2606.4.2.6
OBJECT IDENTIFIER

cmcTcStatusUnit4Sensors		1.3.6.1.4.1.2606.4.2.6.5
OBJECT IDENTIFIER

cmcTcStatusUnit4Outputs		1.3.6.1.4.1.2606.4.2.6.6
OBJECT IDENTIFIER

cmcTcStatusUnit4Msg		1.3.6.1.4.1.2606.4.2.6.7
OBJECT IDENTIFIER

cmcTcStatusExtUnit		1.3.6.1.4.1.2606.4.2.7
OBJECT IDENTIFIER

cmcTcSetup		1.3.6.1.4.1.2606.4.3
OBJECT IDENTIFIER

cmcTcSetupGeneral		1.3.6.1.4.1.2606.4.3.1
OBJECT IDENTIFIER

cmcTcTimerTable1		1.3.6.1.4.1.2606.4.3.1.8
OBJECT IDENTIFIER

cmcTcTrapControl		1.3.6.1.4.1.2606.4.4
OBJECT IDENTIFIER

cmcTcTraps		1.3.6.1.4.1.2606.4.4.7
OBJECT IDENTIFIER

cmcTcControl		1.3.6.1.4.1.2606.4.5
OBJECT IDENTIFIER

cmcTcMibMajRev		1.3.6.1.4.1.2606.4.1.1
The Major Revision level. A change in the major revision level represents a major change in the architecture of the MIB. A change in the major revision level may indicate a significant change in the information, correct interpretation of data may require a MIB document with the same major revision level.
Status: mandatory	Access: read-only
OBJECT-TYPE
	INTEGER	1..65535

cmcTcMibMinRev		1.3.6.1.4.1.2606.4.1.2
The Minor Revision level. A change in the minor revision level may represent some minor additional support, no changes to any pre-existing information has occurred.
Status: mandatory	Access: read-only
OBJECT-TYPE
	INTEGER	0..65535

cmcTcMibCondition		1.3.6.1.4.1.2606.4.1.3
The overall condition (status) of the system represented by this MIB. (2) OK (3) a minor problem, warning condition (yellow LED on CMC) (4) a major problem (red LED on CMC) (5) configuration of sensor units changed or unit detected (red/yellow/green LED on CMC)
Status: mandatory	Access: read-only
OBJECT-TYPE
	INTEGER	other(1), ok(2), degraded(3), failed(4), configChanged(5)

cmcTcStatusDeviceCMC		1.3.6.1.4.1.2606.4.2.1
General Status of CMC-TC unit itself (1) failed (2) OK
Status: mandatory	Access: read-only
OBJECT-TYPE
	INTEGER	failed(1), ok(2)

cmcTcUnitsConnected		1.3.6.1.4.1.2606.4.2.2
Number of sensor units connected to the CMC, Port 1 to 4
Status: mandatory	Access: read-only
OBJECT-TYPE
	INTEGER

cmcTcUnit1TypeOfDevice		1.3.6.1.4.1.2606.4.2.3.1
Type of sensor unit connected to port 1
Status: mandatory	Access: read-only
OBJECT-TYPE
	INTEGER	notAvail(1), unitIO(2), unitAccess(3), unitClimate(4), unitFCS(5), unitRTT(6), unitRCT(7), unitPSM(8), unitPSM8(9), unitPSMMetered(10), unitIOWireless(11), unitPSM6Schuko(12), unitPSM6C19(13), unitFuelCell(14), unitDRC(15), unitTECooler(16), unitPSMMetered32(17), unitPSM8x8(18), unitPSM6x6Schuko(19), unitPSM6x6C19(20)

cmcTcUnit1Text		1.3.6.1.4.1.2606.4.2.3.2
Descriptional text for sensor unit connected to port 1
Status: mandatory	Access: read-write
OBJECT-TYPE
	DisplayString	Size(0..10)

cmcTcUnit1Serial		1.3.6.1.4.1.2606.4.2.3.3
Serialnumber of sensor unit connected to port 1
Status: mandatory	Access: read-only
OBJECT-TYPE
	INTEGER

cmcTcUnit1Status		1.3.6.1.4.1.2606.4.2.3.4
General Status sensor unit connected to port 1 (1) OK (2) error, e. g. value overflow (3) configuration of sensor unit has changed, confirmation required (4) Quit from sensor unit to confirm configuration changes (5) timeout of sensor unit, confirmation required to unload this unit (6) sensor unit detected, needs to be confirmed (7) unit is not available (8) supply voltage is too low (9) Firmware upgrade running
Status: mandatory	Access: read-only
OBJECT-TYPE
	INTEGER	ok(1), error(2), changed(3), quit(4), timeout(5), detected(6), notAvail(7), lowPower(8), fwUpgrade(9)

cmcTcUnit1NumberOfSensors		1.3.6.1.4.1.2606.4.2.3.5.1
Number of sensors connected to sensor unit 1
Status: mandatory	Access: read-only
OBJECT-TYPE
	INTEGER

cmcTcUnit1SensorTable		1.3.6.1.4.1.2606.4.2.3.5.2
Headline of sensor table
Status: mandatory	Access: not-accessible
OBJECT-TYPE
	SEQUENCE OF
		CmcTcUnit1SensorEntry

cmcTcUnit1SensorEntry		1.3.6.1.4.1.2606.4.2.3.5.2.1
Entries of sensor table
Status: mandatory	Access: not-accessible
OBJECT-TYPE
	CmcTcUnit1SensorEntry

unit1SensorIndex		1.3.6.1.4.1.2606.4.2.3.5.2.1.1
Index for the list of value entries. Its value ranges between 1 and the value of cmcTcUnit1NumberOfSensors.
Status: mandatory	Access: read-only
OBJECT-TYPE
	INTEGER	1..65535

unit1SensorType		1.3.6.1.4.1.2606.4.2.3.5.2.1.2
Type of sensor which is connected to sensor unit 1 to sensor[unit1SensorIndex] 1: no sensor connected 2: sensor failure 3: value overflow 4: sensor type 1, access sensor 5: sensor type 2, vibration sensor 6: sensor type 3, motion sensor 7: sensor type 4, smoke sensor 8: sensor type 5, air flow sensor 9: sensor type 6, reserved 10: sensor type 7, temperature sensor 11: sensor type 8, 4..20mA sensor 12: sensor type 9, humidity sensor 13: user sensor with normally opened contact 14: user sensor with normally closed contact 15: door locked sensor from locking device 16: remote unlock sensor (e.g. external keypad) 17: voltage sensor, indicates status of main voltage (OK, NOK) 18: voltage value 19: fan status, from CMC-TC-FAS-Unit 20: cardreader or keypad, connected to I2C port 21: duty cycle of fan, FCS-Unit 22: status of fan, FCS-Unit 23: leakage sensor 24: warning, RittalTopTherm(RTT)-Unit 25: alarm, RittalTopTherm-Unit 26: temperature difference filter monitor, RTT-Unit 27: heatflow RCT-Unit 28: alarm RCT-Unit 29: warning RCT-Unit 30: actual current*10, PSM-Unit 31: status PSM-Unit 32: position PSM-Unit, normal/reversed = circuit 1/2 33: air Flap 34: acoustic sensor 35: DET-AC fault (extinguisher) 36: DET-AC first alarm (extinguisher) 37: DET-AC main alarm (extinguisher) 38: DRC: RFID Tag 40-47: RPM Fan 1.1 - Fan 4.2, LCP 48-55: Air temperature 1.1 - 4.2, LCP 56,57: actual temperature 1,2, LCP 58: water inlet temperature, LCP 59: water outlet temperature, LCP 60: water flow 61: fan speed (desired value) 62: status valve, LCP 63: status LCP 64: temperature difference water temperatures 65: control temperature 1, LCP 66: control temperature 2, LCP 67: condensate pump, duration, LCP 68: condensate pump, cycles, LCP 72: total energy*10 (kWh), PSM 73: total power*10 (kW), PSM 74: frequency*10 (Hz), PSM 75: voltage*10 (V), PSM 76: voltage status, PSM 77: current*10 (A), PSM 78: current status, PSM 79: power*10 (kW) per phase, PSM 80: energy*10 (kWh) per phase, PSM 81: temporary energy*10 (kWh) per phase, PSM 100: temperature sensor, wireless 101: temperature sensor (combi), wireless 102: humidity sensor, wireless 103: access sensor, wireless 104: user sensor with normally opened contact, wireless 105: user sensor with normally closed contact, wireless 106: analog sensor 4..20mA, wireless
Status: mandatory	Access: read-only
OBJECT-TYPE
	INTEGER	notAvail(1), failure(2), overflow(3), access(4), vibration(5), motion(6), smoke(7), airFlow(8), type6(9), temperature(10), current4to20(11), humidity(12), userNO(13), userNC(14), lock(15), unlock(16), voltOK(17), voltage(18), fanOK(19), readerKeypad(20), dutyPWM(21), fanStatus(22), leakage(23), warningRTT(24), alarmRTT(25), filterRTT(26), heatflowRCT(27), alarmRCT(28), warningRCT(29), currentPSM(30), statusPSM(31), positionPSM(32), airFlap(33), acoustic(34), detACfault(35), detACfirstAlarm(36), detACmainAlarm(37), rfidTag(38), rpm11LCP(40), rpm12LCP(41), rpm21LCP(42), rpm22LCP(43), rpm31LCP(44), rpm32LCP(45), rpm41LCP(46), rpm42LCP(47), airTemp11LCP(48), airTemp12LCP(49), airTemp21LCP(50), airTemp22LCP(51), airTemp31LCP(52), airTemp32LCP(53), airTemp41LCP(54), airTemp42LCP(55), temp1LCP(56), temp2LCP(57), waterInTemp(58), waterOutTemp(59), waterFlow(60), fanSpeed(61), valve(62), statusLCP(63), waterDelta(64), valveActual(65), contrTemp2(66), condensateDuration(67), condensateCycles(68), totalKWhPSM(72), totalKWPSM(73), frequencyPSM(74), voltagePSM(75), voltStatusPSM(76), amperePSM(77), ampStatusPSM(78), kWPSM(79), kWhPSM(80), kWhTempPSM(81), temperatureWL(100), temperature1WL(101), humidityWL(102), accessWL(103), userNOWL(104), userNCWL(105), analogWL(106)

unit1SensorText		1.3.6.1.4.1.2606.4.2.3.5.2.1.3
Descriptional text for each sensor (entry in the table)
Status: mandatory	Access: read-write
OBJECT-TYPE
	DisplayString	Size(0..20)

unit1SensorStatus		1.3.6.1.4.1.2606.4.2.3.5.2.1.4
Actual status of the sensor
Status: mandatory	Access: read-only
OBJECT-TYPE
	INTEGER	notAvail(1), lost(2), changed(3), ok(4), off(5), on(6), warning(7), tooLow(8), tooHigh(9), error(10)

unit1SensorValue		1.3.6.1.4.1.2606.4.2.3.5.2.1.5
Value of sensor
Status: mandatory	Access: read-only
OBJECT-TYPE
	INTEGER

unit1SensorSetHigh		1.3.6.1.4.1.2606.4.2.3.5.2.1.6
Value for high setpoint of sensor
Status: mandatory	Access: read-write
OBJECT-TYPE
	INTEGER

unit1SensorSetLow		1.3.6.1.4.1.2606.4.2.3.5.2.1.7
Value for low setpoint of sensor, also used as alarm delay
Status: mandatory	Access: read-write
OBJECT-TYPE
	INTEGER

unit1SensorSetWarn		1.3.6.1.4.1.2606.4.2.3.5.2.1.8
Value for warning setpoint of sensor, also used as fan threshold
Status: mandatory	Access: read-write
OBJECT-TYPE
	INTEGER

unit1SensorHysteresis		1.3.6.1.4.1.2606.4.2.3.5.2.1.9
% -Value for hysteresis for High, Low and Warning, input in % from actual setpoint
Status: mandatory	Access: read-write
OBJECT-TYPE
	INTEGER

unit1SensorDisplayFactor		1.3.6.1.4.1.2606.4.2.3.5.2.1.10
Factor of sensor value and setpoints, devide actual value with this value, e. g. factor = 10: sensor value = 100, actual value = 10.0
Status: mandatory	Access: read-only
OBJECT-TYPE
	INTEGER

unit1SensorScaleStart		1.3.6.1.4.1.2606.4.2.3.5.2.1.11
Value for start value for scaling of 0..100% (4..20mA) sensor, example: acutal range of value of 4..20mA sensor is from 10 to 60A, then this variable is set to 10, also valid for setpoints
Status: mandatory	Access: read-write
OBJECT-TYPE
	INTEGER

unit1SensorScaleEnd		1.3.6.1.4.1.2606.4.2.3.5.2.1.12
Value for end value for scaling of 0..100% (4..20mA) sensor, example: acutal range of value of 4..20mA sensor is from 10 to 60A, then this variable is set to 60, also valid for setpoints
Status: mandatory	Access: read-write
OBJECT-TYPE
	INTEGER

unit1SensorUnit		1.3.6.1.4.1.2606.4.2.3.5.2.1.13
Unit for 0..100% (4..20mA) sensor, example: acutal range of value of 4..20mA sensor is from 10 to 60A, then this variable is set to 'A'
Status: mandatory	Access: read-write
OBJECT-TYPE
	DisplayString	Size(0..10)

unit1SensorInfo		1.3.6.1.4.1.2606.4.2.3.5.2.1.14
Additional information to the sensor, e. g. Serialnumber, Signal Quality..
Status: mandatory	Access: read-only
OBJECT-TYPE
	DisplayString	Size(0..50)

cmcTcUnit1NumberOfOutputs		1.3.6.1.4.1.2606.4.2.3.6.1
Number of outputs available on sensor unit 1
Status: mandatory	Access: read-only
OBJECT-TYPE
	INTEGER

cmcTcUnit1OutputTable		1.3.6.1.4.1.2606.4.2.3.6.2
Headline of output table
Status: mandatory	Access: not-accessible
OBJECT-TYPE
	SEQUENCE OF
		CmcTcUnit1OutputEntry

cmcTcUnit1OutputEntry		1.3.6.1.4.1.2606.4.2.3.6.2.1
Entries of output table
Status: mandatory	Access: not-accessible
OBJECT-TYPE
	CmcTcUnit1OutputEntry

unit1OutputIndex		1.3.6.1.4.1.2606.4.2.3.6.2.1.1
Index for the list of output entries. Its value ranges between 1 and the value of cmcTcUnit1NumberOfOutputs.
Status: mandatory	Access: read-only
OBJECT-TYPE
	INTEGER	1..65535

unit1OutputType		1.3.6.1.4.1.2606.4.2.3.6.2.1.2
Type of output which is connected to sensor unit 1 to output[unit1OutputIndex] 1: no output connected 2: output failure 3: value overflow 4: output type 1, door locking TS8,Ergoform 5: output type 2, universal lock 1, lock with power 6: output type 3, universal lock 2, unlock with power 7: output type 4, fan relay 8: output type 5, fan controlled 9: output type 6, universal relay output 10: output type 7, room door lock 11: output type 8, power output 12: output type 9, door lock with Master key 13: output type 10, door lock FR(i) 14: setpoint (FCS, LCP) 15: setpoint temperature monitoring (LCP) 16: hysteresis of setpoint (LCP) 17: command for remote control of RCT 18: relay PSM, 1=On, 0=Off 19: high setpoint current monitoring PSM 20: low setpoint current monitoring PSM 21: setpoint temperature RTT 22: setpoint temperature monitoring RTT 23: power output 20A 24: door magnet (automatic door release) 30: control mode, LCP 31: min fan speed (fan control), LCP 32: min delta T (fan control), LCP 33: max delta T (fan control), LCP 34: PID controller, KP, LCP 35: PID controller, KI, LCP 36 PID controller, KD, LCP 37 flowrate flowmeter, LCP 38: cw value of water (default: 4187), LCP 39: deltaT, LCP 40: control mode, LCP 42: setpoint high voltage PSM 43: setpoint low voltage PSM 44: setpoint high current PSM 45: setpoint low current PSM 46: command PSM
Status: mandatory	Access: read-only
OBJECT-TYPE
	INTEGER	notAvail(1), failure(2), overflow(3), doorLock(4), univLock1(5), univLock2(6), fan(7), fanSpeedContr(8), universalOut(9), roomLock(10), powerOut(11), doorLockMaster(12), doorLockFRi(13), setpoint(14), setpointTimax(15), hysteresisRCT(16), commandRCT(17), relayPSM(18), setHighPSM(19), setLowPSM(20), setpointRTT(21), setTimaxRTT(22), powerOut1(23), doorMagnet(24), controlModeLCP(30), minFanSpeedLCP(31), minDeltaTLCP(32), maxDeltaTLCP(33), kPLCP(34), kILCP(35), kDLCP(36), flowRateLCP(37), cwValueLCP(38), deltaTLCP(39), ctrModLCP(40), voltHighPSM(42), voltLowPSM(43), ampHighPSM(44), ampLowPSM(45), commandPSM(46)

unit1OutputText		1.3.6.1.4.1.2606.4.2.3.6.2.1.3
Descriptional text for each output (entry in the table)
Status: mandatory	Access: read-write
OBJECT-TYPE
	DisplayString	Size(0..20)

unit1OutputStatus		1.3.6.1.4.1.2606.4.2.3.6.2.1.4
Actual status of the output
Status: mandatory	Access: read-write
OBJECT-TYPE
	INTEGER	notAvail(1), lost(2), changed(3), ok(4), off(5), on(6), setOff(7), setOn(8)

unit1OutputValue		1.3.6.1.4.1.2606.4.2.3.6.2.1.5
Value for output
Status: mandatory	Access: read-write
OBJECT-TYPE
	INTEGER

unit1OutputSet		1.3.6.1.4.1.2606.4.2.3.6.2.1.6
Command for output
Status: mandatory	Access: read-write
OBJECT-TYPE
	INTEGER	off(1), on(2), lock(3), unlock(4), unlockDelay(5)

unit1OutputConfig		1.3.6.1.4.1.2606.4.2.3.6.2.1.7
Configuration for output 1: disable remote control (e.g. keypad) 2: enable remote control
Status: mandatory	Access: read-write
OBJECT-TYPE
	INTEGER	disRemote(1), enRemote(2)

unit1OutputDelay		1.3.6.1.4.1.2606.4.2.3.6.2.1.8
Unsigned Value for delay, after this time the output will fall into the previous state
Status: mandatory	Access: read-write
OBJECT-TYPE
	INTEGER

unit1OutputTimeoutAction		1.3.6.1.4.1.2606.4.2.3.6.2.1.9
State for output if timeout (RS422) occurs
Status: mandatory	Access: read-write
OBJECT-TYPE
	INTEGER	stay(1), off(2), on(3)

cmcTcUnit1NumberOfMsgs		1.3.6.1.4.1.2606.4.2.3.7.1
Number of messages that can be created with sensor unit 1
Status: mandatory	Access: read-only
OBJECT-TYPE
	INTEGER

cmcTcUnit1MsgTable		1.3.6.1.4.1.2606.4.2.3.7.2
Headline of message table
Status: mandatory	Access: not-accessible
OBJECT-TYPE
	SEQUENCE OF
		CmcTcUnit1MsgEntry

cmcTcUnit1MsgEntry		1.3.6.1.4.1.2606.4.2.3.7.2.1
Entries of message table
Status: mandatory	Access: not-accessible
OBJECT-TYPE
	CmcTcUnit1MsgEntry

unit1MsgIndex		1.3.6.1.4.1.2606.4.2.3.7.2.1.1
Index for the list of message entries. Its value ranges between 1 and the value of cmcTcUnit1NumberOfMsgs.
Status: mandatory	Access: read-only
OBJECT-TYPE
	INTEGER	1..65535

unit1MsgText		1.3.6.1.4.1.2606.4.2.3.7.2.1.2
Descriptional text for each message (entry in the table)
Status: mandatory	Access: read-write
OBJECT-TYPE
	DisplayString	Size(0..20)

unit1MsgStatus		1.3.6.1.4.1.2606.4.2.3.7.2.1.3
Actual message status 1: not available 2: configuration has changed (sensor new, changed, lost) 3: error 4: OK 5: alarm, e.g. smoke, vibration... 6: warning of analog value, value reached warning threshold 7: analog value too low, value reached low threshold 8: analog value too high, value reached high threshold 9: output is set to OFF 10: output is set to ON 11: door is open 12: door is closed 13: door is locked 14: door is unlocked by remote input, e.g. external cardreader 15: door is unlocked by reader or keypad connected to I2C 16: door is unlocked by SNMP set command (unit1OutputSet) 17: door is unlocked by WEB 18: door is unlocked by timer 19: no access, wrong keycode or cardnumber 20: orientation of PSM-Unit is circuit 1 21: orientation of PSM-Unit is circuit 2 22: battery low, wireless sensor
Status: mandatory	Access: read-only
OBJECT-TYPE
	INTEGER	notAvail(1), configChanged(2), error(3), ok(4), alarm(5), warning(6), tooLow(7), tooHigh(8), setOff(9), setOn(10), open(11), closed(12), locked(13), unlRemote(14), unlReaderKeypad(15), unlSNMP(16), unlWEB(17), unlTimer(18), noAccess(19), circuit1(20), circuit2(21), lowBatt(22)

unit1MsgRelay		1.3.6.1.4.1.2606.4.2.3.7.2.1.4
Setup of Alarm relay for this message/alarm 1: no switching of alarm relay 2: switching of alarm relay
Status: mandatory	Access: read-write
OBJECT-TYPE
	INTEGER	disable(1), enable(2)

unit1MsgBeeper		1.3.6.1.4.1.2606.4.2.3.7.2.1.5
Setup of Alarm beeper for this alarm 1: no audible alarm 2: audible alarm
Status: mandatory	Access: read-write
OBJECT-TYPE
	INTEGER	disable(1), enable(2)

unit1MsgTrap1		1.3.6.1.4.1.2606.4.2.3.7.2.1.6
Trap receiver 1 activated
Status: mandatory	Access: read-write
OBJECT-TYPE
	INTEGER	disable(1), enable(2)

unit1MsgTrap2		1.3.6.1.4.1.2606.4.2.3.7.2.1.7
Trap receiver 2 activated
Status: mandatory	Access: read-write
OBJECT-TYPE
	INTEGER	disable(1), enable(2)

unit1MsgTrap3		1.3.6.1.4.1.2606.4.2.3.7.2.1.8
Trap receiver 3 activated
Status: mandatory	Access: read-write
OBJECT-TYPE
	INTEGER	disable(1), enable(2)

unit1MsgTrap4		1.3.6.1.4.1.2606.4.2.3.7.2.1.9
Trap receiver 4 and Event Logging activated
Status: mandatory	Access: read-write
OBJECT-TYPE
	INTEGER	disable(1), enable(2)

unit1MsgQuit		1.3.6.1.4.1.2606.4.2.3.7.2.1.10
Reset of this alarm 1: auto 2: manual, alarm needs confirmation, e. g. with 'C' key
Status: mandatory	Access: read-write
OBJECT-TYPE
	INTEGER	auto(1), manual(2)

unit1MsgDelay		1.3.6.1.4.1.2606.4.2.3.7.2.1.11
Delay of alarm condition
Status: mandatory	Access: read-write
OBJECT-TYPE
	INTEGER

cmcTcUnit2TypeOfDevice		1.3.6.1.4.1.2606.4.2.4.1
Type of sensor unit connected to port 2
Status: mandatory	Access: read-only
OBJECT-TYPE
	INTEGER	notAvail(1), unitIO(2), unitAccess(3), unitClimate(4), unitFCS(5), unitRTT(6), unitRCT(7), unitPSM(8), unitPSM8(9), unitPSMMetered(10), unitIOWireless(11), unitPSM6Schuko(12), unitPSM6C19(13), unitFuelCell(14), unitDRC(15), unitTECooler(16), unitPSMMetered32(17), unitPSM8x8(18), unitPSM6x6Schuko(19), unitPSM6x6C19(20)

cmcTcUnit2Text		1.3.6.1.4.1.2606.4.2.4.2
Descriptional text for sensor unit connected to port 2
Status: mandatory	Access: read-write
OBJECT-TYPE
	DisplayString	Size(0..10)

cmcTcUnit2Serial		1.3.6.1.4.1.2606.4.2.4.3
Serialnumber of sensor unit connected to port 2
Status: mandatory	Access: read-only
OBJECT-TYPE
	INTEGER

cmcTcUnit2Status		1.3.6.1.4.1.2606.4.2.4.4
General Status sensor unit connected to port 2 (1) OK (2) error (3) configuration of sensor unit has changed, confirmation required (4) Quit from sensor unit to confirm configuration changes (5) timeout of sensor unit, confirmation required (6) sensor unit detected, needs to be confirmed (8) supply voltage is too low (9) Firmware upgrade running
Status: mandatory	Access: read-only
OBJECT-TYPE
	INTEGER	ok(1), error(2), changed(3), quit(4), timeout(5), detected(6), notAvail(7), lowPower(8), fwUpgrade(9)

cmcTcUnit2NumberOfSensors		1.3.6.1.4.1.2606.4.2.4.5.1
Number of sensors connected to sensor unit 2
Status: mandatory	Access: read-only
OBJECT-TYPE
	INTEGER

cmcTcUnit2SensorTable		1.3.6.1.4.1.2606.4.2.4.5.2
Headline of sensor table
Status: mandatory	Access: not-accessible
OBJECT-TYPE
	SEQUENCE OF
		CmcTcUnit2SensorEntry

cmcTcUnit2SensorEntry		1.3.6.1.4.1.2606.4.2.4.5.2.1
Entries of sensor table
Status: mandatory	Access: not-accessible
OBJECT-TYPE
	CmcTcUnit2SensorEntry

unit2SensorIndex		1.3.6.1.4.1.2606.4.2.4.5.2.1.1
Index for the list of value entries. Its value ranges between 1 and the value of cmcTcUnit2NumberOfSensors.
Status: mandatory	Access: read-only
OBJECT-TYPE
	INTEGER	1..65535

unit2SensorType		1.3.6.1.4.1.2606.4.2.4.5.2.1.2
Type of sensor which is connected to sensor unit 2 to sensor[unit2SensorIndex] 1: no sensor connected 2: sensor failure 3: value overflow 4: sensor type 1, access sensor 5: sensor type 2, vibration sensor 6: sensor type 3, motion sensor 7: sensor type 4, smoke sensor 8: sensor type 5, air flow sensor 9: sensor type 6, reserved 10: sensor type 7, temperature sensor 11: sensor type 8, 4..20mA sensor 12: sensor type 9, humidity sensor 13: user sensor with normally opened contact 14: user sensor with normally closed contact 15: door locked sensor from locking device 16: remote unlock sensor (e.g. external keypad) 17: voltage sensor, indicates status of main voltage 18: voltage value 19: fan status 20: cardreader or keypad, connected to I2C port 21: duty cycle of fan, FCS-Unit 22: status of fan, FCS-Unit 23: leakage sensor 24: warning, RittalTopTherm(RTT)-Unit 25: alarm, RittalTopTherm-Unit 26: temperature difference filter monitor, RTT-Unit 27: heatflow RCT-Unit 28: alarm RCT-Unit 29: warning RCT-Unit 30: actual current*10, PSM-Unit 31: status PSM-Unit 32: position PSM-Unit, normal/reversed = circuit 1/2 33: air Flap 34: acoustic sensor 35: DET-AC fault (extinguisher) 36: DET-AC first alarm (extinguisher) 37: DET-AC main alarm (extinguisher) 38: DRC: RFID Tag 40-47: RPM Fan 1.1 - Fan 4.2, LCP 48-55: Air temperature 1.1 - 4.2, LCP 56,57: actual temperature 1,2, LCP 58: water inlet temperature, LCP 59: water outlet temperature, LCP 60: water flow 61: fan speed (desired value) 62: status valve, LCP 63: status LCP 64: temperature difference water temperatures 65: control temperature 1, LCP 66: control temperature 2, LCP 67: condensate pump, duration, LCP 68: condensate pump, cycles, LCP 72: total energy*10 (kWh), PSM 73: total power*10 (kW), PSM 74: frequency*10 (Hz), PSM 75: voltage*10 (V), PSM 76: voltage status, PSM 77: current*10 (A), PSM 78: current status, PSM 79: power*10 (kW) per phase, PSM 80: energy*10 (kWh) per phase, PSM 81: temporary energy*10 (kWh) per phase, PSM 100: temperature sensor, wireless 101: temperature sensor (combi), wireless 102: humidity sensor, wireless 103: access sensor, wireless 104: user sensor with normally opened contact, wireless 105: user sensor with normally closed contact, wireless 106: analog sensor 4..20mA, wireless
Status: mandatory	Access: read-only
OBJECT-TYPE
	INTEGER	notAvail(1), failure(2), overflow(3), access(4), vibration(5), motion(6), smoke(7), airFlow(8), type6(9), temperature(10), current4to20(11), humidity(12), userNO(13), userNC(14), lock(15), unlock(16), voltOK(17), voltage(18), fanOK(19), readerKeypad(20), dutyPWM(21), fanStatus(22), leakage(23), warningRTT(24), alarmRTT(25), filterRTT(26), heatflowRCT(27), alarmRCT(28), warningRCT(29), currentPSM(30), statusPSM(31), positionPSM(32), airFlap(33), acoustic(34), detACfault(35), detACfirstAlarm(36), detACmainAlarm(37), rfidTag(38), rpm11LCP(40), rpm12LCP(41), rpm21LCP(42), rpm22LCP(43), rpm31LCP(44), rpm32LCP(45), rpm41LCP(46), rpm42LCP(47), airTemp11LCP(48), airTemp12LCP(49), airTemp21LCP(50), airTemp22LCP(51), airTemp31LCP(52), airTemp32LCP(53), airTemp41LCP(54), airTemp42LCP(55), temp1LCP(56), temp2LCP(57), waterInTemp(58), waterOutTemp(59), waterFlow(60), fanSpeed(61), valve(62), statusLCP(63), waterDelta(64), valveActual(65), contrTemp2(66), condensateDuration(67), condensateCycles(68), totalKWhPSM(72), totalKWPSM(73), frequencyPSM(74), voltagePSM(75), voltStatusPSM(76), amperePSM(77), ampStatusPSM(78), kWPSM(79), kWhPSM(80), kWhTempPSM(81), temperatureWL(100), temperature1WL(101), humidityWL(102), accessWL(103), userNOWL(104), userNCWL(105), analogWL(106)

unit2SensorText		1.3.6.1.4.1.2606.4.2.4.5.2.1.3
Descriptional text for each sensor (entry in the table)
Status: mandatory	Access: read-write
OBJECT-TYPE
	DisplayString	Size(0..20)

unit2SensorStatus		1.3.6.1.4.1.2606.4.2.4.5.2.1.4
Actual status of the sensor
Status: mandatory	Access: read-only
OBJECT-TYPE
	INTEGER	notAvail(1), lost(2), changed(3), ok(4), off(5), on(6), warning(7), tooLow(8), tooHigh(9), error(10)

unit2SensorValue		1.3.6.1.4.1.2606.4.2.4.5.2.1.5
Value of sensor
Status: mandatory	Access: read-only
OBJECT-TYPE
	INTEGER

unit2SensorSetHigh		1.3.6.1.4.1.2606.4.2.4.5.2.1.6
Value for high setpoint of sensor
Status: mandatory	Access: read-write
OBJECT-TYPE
	INTEGER

unit2SensorSetLow		1.3.6.1.4.1.2606.4.2.4.5.2.1.7
Value for low setpoint of sensor, also used as alarm delay
Status: mandatory	Access: read-write
OBJECT-TYPE
	INTEGER

unit2SensorSetWarn		1.3.6.1.4.1.2606.4.2.4.5.2.1.8
Value for warning setpoint of sensor, also used as fan threshold
Status: mandatory	Access: read-write
OBJECT-TYPE
	INTEGER

unit2SensorHysteresis		1.3.6.1.4.1.2606.4.2.4.5.2.1.9
% -Value for hysteresis for High, Low and Warning, input in % from actual setpoint
Status: mandatory	Access: read-write
OBJECT-TYPE
	INTEGER

unit2SensorDisplayFactor		1.3.6.1.4.1.2606.4.2.4.5.2.1.10
Factor of sensor value and setpoints, devide actual value with this value, e. g. factor = 10: sensor value = 100, actual value = 10.0
Status: mandatory	Access: read-only
OBJECT-TYPE
	INTEGER

unit2SensorScaleStart		1.3.6.1.4.1.2606.4.2.4.5.2.1.11
Value for start value for scaling of 0..100% (4..20mA) sensor, example: acutal range of value of 4..20mA sensor is from 10 to 60A, then this variable is set to 10, also valid for setpoints
Status: mandatory	Access: read-write
OBJECT-TYPE
	INTEGER

unit2SensorScaleEnd		1.3.6.1.4.1.2606.4.2.4.5.2.1.12
Value for end value for scaling of 0..100% (4..20mA) sensor, example: acutal range of value of 4..20mA sensor is from 10 to 60A, then this variable is set to 60, also valid for setpoints
Status: mandatory	Access: read-write
OBJECT-TYPE
	INTEGER

unit2SensorUnit		1.3.6.1.4.1.2606.4.2.4.5.2.1.13
Unit for 0..100% (4..20mA) sensor, example: acutal range of value of 4..20mA sensor is from 10 to 60A, then this variable is set to 'A'
Status: mandatory	Access: read-write
OBJECT-TYPE
	DisplayString	Size(0..10)

unit2SensorInfo		1.3.6.1.4.1.2606.4.2.4.5.2.1.14
Additional information to the sensor, e. g. Serialnumber, Signal Quality..
Status: mandatory	Access: read-only
OBJECT-TYPE
	DisplayString	Size(0..50)

cmcTcUnit2NumberOfOutputs		1.3.6.1.4.1.2606.4.2.4.6.1
Number of outputs available on sensor unit 2
Status: mandatory	Access: read-only
OBJECT-TYPE
	INTEGER

cmcTcUnit2OutputTable		1.3.6.1.4.1.2606.4.2.4.6.2
Headline of output table
Status: mandatory	Access: not-accessible
OBJECT-TYPE
	SEQUENCE OF
		CmcTcUnit2OutputEntry

cmcTcUnit2OutputEntry		1.3.6.1.4.1.2606.4.2.4.6.2.1
Entries of output table
Status: mandatory	Access: not-accessible
OBJECT-TYPE
	CmcTcUnit2OutputEntry

unit2OutputIndex		1.3.6.1.4.1.2606.4.2.4.6.2.1.1
Index for the list of output entries. Its value ranges between 1 and the value of cmcTcUnit2NumberOfOutputs.
Status: mandatory	Access: read-only
OBJECT-TYPE
	INTEGER	1..65535

unit2OutputType		1.3.6.1.4.1.2606.4.2.4.6.2.1.2
Type of output which is connected to sensor unit 2 to output[unit2OutputIndex] 1: no output connected 2: output failure 3: value overflow 4: output type 1, door locking TS8,Ergoform 5: output type 2, universal lock 1, lock with power 6: output type 3, universal lock 2, unlock with power 7: output type 4, fan relay 8: output type 5, fan controlled 9: output type 6, universal relay output 10: output type 7, room door lock 11: output type 8, power output 12: output type 9, door lock with Master key 13: output type 10, door lock FR(i) 14: setpoint (FCS, RTT) 15: setpoint temperature monitoring (RTT) 16: hysteresis of setpoint (RCT) 17: command for remote control of RCT 18: relay PSM, 1=On, 0=Off 19: high setpoint current monitoring PSM 20: low setpoint current monitoring PSM 21: setpoint temperature RTT 22: setpoint temperature monitoring RTT 23: power output 20A 24: door magnet (automatic door release) 30: control mode LCP 31: min fan speed (fan control) LCP 32: min delta T (fan control) LCP 33: max delta T (fan control) LCP 34: PID controller, KP, LCP 35: PID controller, KI, LCP 36 PID controller, KD, LCP 37 flowrate flowmeter, LCP 38: cw value of water (default: 4187) LCP 39: deltaT, LCP 40: control mode, LCP 42: setpoint high voltage PSM 43: setpoint low voltage PSM 44: setpoint high current PSM 45: setpoint low current PSM 46: command PSM
Status: mandatory	Access: read-only
OBJECT-TYPE
	INTEGER	notAvail(1), failure(2), overflow(3), doorLock(4), univLock1(5), univLock2(6), fan(7), fanSpeedContr(8), universalOut(9), roomLock(10), powerOut(11), doorLockMaster(12), doorLockFRi(13), setpoint(14), setpointTimax(15), hysteresisRCT(16), commandRCT(17), relayPSM(18), setHighPSM(19), setLowPSM(20), setpointRTT(21), setTimaxRTT(22), powerOut1(23), doorMagnet(24), controlModeLCP(30), minFanSpeedLCP(31), minDeltaTLCP(32), maxDeltaTLCP(33), kPLCP(34), kILCP(35), kDLCP(36), flowRateLCP(37), cwValueLCP(38), deltaTLCP(39), ctrModLCP(40), voltHighPSM(42), voltLowPSM(43), ampHighPSM(44), ampLowPSM(45), commandPSM(46)

unit2OutputText		1.3.6.1.4.1.2606.4.2.4.6.2.1.3
Descriptional text for each output (entry in the table)
Status: mandatory	Access: read-write
OBJECT-TYPE
	DisplayString	Size(0..20)

unit2OutputStatus		1.3.6.1.4.1.2606.4.2.4.6.2.1.4
Actual status of the output
Status: mandatory	Access: read-write
OBJECT-TYPE
	INTEGER	notAvail(1), lost(2), changed(3), ok(4), off(5), on(6), setOff(7), setOn(8)

unit2OutputValue		1.3.6.1.4.1.2606.4.2.4.6.2.1.5
Signed value for output
Status: mandatory	Access: read-write
OBJECT-TYPE
	INTEGER

unit2OutputSet		1.3.6.1.4.1.2606.4.2.4.6.2.1.6
Command for output
Status: mandatory	Access: read-write
OBJECT-TYPE
	INTEGER	off(1), on(2), lock(3), unlock(4), unlockDelay(5)

unit2OutputConfig		1.3.6.1.4.1.2606.4.2.4.6.2.1.7
Configuration for output 1: disable remote control (e.g. keypad) 2: enable remote control
Status: mandatory	Access: read-write
OBJECT-TYPE
	INTEGER	disRemote(1), enRemote(2)

unit2OutputDelay		1.3.6.1.4.1.2606.4.2.4.6.2.1.8
Unsigned Value for delay, after this time the output will fall into the previous state
Status: mandatory	Access: read-write
OBJECT-TYPE
	INTEGER

unit2OutputTimeoutAction		1.3.6.1.4.1.2606.4.2.4.6.2.1.9
State for output if timeout (RS422) occurs
Status: mandatory	Access: read-write
OBJECT-TYPE
	INTEGER	stay(1), off(2), on(3)

cmcTcUnit2NumberOfMsgs		1.3.6.1.4.1.2606.4.2.4.7.1
Number of alarms that can be created with sensor unit 2
Status: mandatory	Access: read-only
OBJECT-TYPE
	INTEGER

cmcTcUnit2MsgTable		1.3.6.1.4.1.2606.4.2.4.7.2
Headline of message table
Status: mandatory	Access: not-accessible
OBJECT-TYPE
	SEQUENCE OF
		CmcTcUnit2MsgEntry

cmcTcUnit2MsgEntry		1.3.6.1.4.1.2606.4.2.4.7.2.1
Entries of message table
Status: mandatory	Access: not-accessible
OBJECT-TYPE
	CmcTcUnit2MsgEntry

unit2MsgIndex		1.3.6.1.4.1.2606.4.2.4.7.2.1.1
Index for the list of alarm entries. Its value ranges between 1 and the value of cmcTcUnit2NumberOfMsgs.
Status: mandatory	Access: read-only
OBJECT-TYPE
	INTEGER	1..65535

unit2MsgText		1.3.6.1.4.1.2606.4.2.4.7.2.1.2
Descriptional text for each message (entry in the table)
Status: mandatory	Access: read-write
OBJECT-TYPE
	DisplayString	Size(0..20)

unit2MsgStatus		1.3.6.1.4.1.2606.4.2.4.7.2.1.3
Actual message status 1: not available 2: configuration has changed (sensor new, changed, lost) 3: error 4: OK 5: alarm, e.g. smoke, vibration... 6: warning of analog value, value reached warning threshold 7: analog value too low, value reached low threshold 8: analog value too high, value reached high threshold 9: output is set to OFF 10: output is set to ON 11: door is open 12: door is closed 13: door is locked 14: door is unlocked by remote input, e.g. external cardreader 15: door is unlocked by reader or keypad connected to I2C 16: door is unlocked by SNMP set command (unit1OutputSet) 17: door is unlocked by WEB 18: door is unlocked by timer 19: no access, wrong keycode or cardnumber 20: orientation of PSM-Unit is circuit 1 21: orientation of PSM-Unit is circuit 2 22: battery low, wireless sensor
Status: mandatory	Access: read-only
OBJECT-TYPE
	INTEGER	notAvail(1), configChanged(2), error(3), ok(4), alarm(5), warning(6), tooLow(7), tooHigh(8), setOff(9), setOn(10), open(11), closed(12), locked(13), unlRemote(14), unlReaderKeypad(15), unlSNMP(16), unlWEB(17), unlTimer(18), noAccess(19), circuit1(20), circuit2(21), lowBatt(22)

unit2MsgRelay		1.3.6.1.4.1.2606.4.2.4.7.2.1.4
Setup of Alarm relay for this alarm 2: no switching of alarm relay 1: switching of alarm relay
Status: mandatory	Access: read-write
OBJECT-TYPE
	INTEGER	disable(1), enable(2)

unit2MsgBeeper		1.3.6.1.4.1.2606.4.2.4.7.2.1.5
Setup of Alarm beeper for this alarm 2: no audible alarm 1: audible alarm
Status: mandatory	Access: read-write
OBJECT-TYPE
	INTEGER	disable(1), enable(2)

unit2MsgTrap1		1.3.6.1.4.1.2606.4.2.4.7.2.1.6
Trap receiver 1 activated
Status: mandatory	Access: read-write
OBJECT-TYPE
	INTEGER	disable(1), enable(2)

unit2MsgTrap2		1.3.6.1.4.1.2606.4.2.4.7.2.1.7
Trap receiver 2 activated
Status: mandatory	Access: read-write
OBJECT-TYPE
	INTEGER	disable(1), enable(2)

unit2MsgTrap3		1.3.6.1.4.1.2606.4.2.4.7.2.1.8
Trap receiver 3 activated
Status: mandatory	Access: read-write
OBJECT-TYPE
	INTEGER	disable(1), enable(2)

unit2MsgTrap4		1.3.6.1.4.1.2606.4.2.4.7.2.1.9
Trap receiver 4 and Event Logging activated
Status: mandatory	Access: read-write
OBJECT-TYPE
	INTEGER	disable(1), enable(2)

unit2MsgQuit		1.3.6.1.4.1.2606.4.2.4.7.2.1.10
Reset of this alarm 1: auto 2: manual, alarm needs confirmation, e. g. with 'C' key
Status: mandatory	Access: read-write
OBJECT-TYPE
	INTEGER	auto(1), manual(2)

unit2MsgDelay		1.3.6.1.4.1.2606.4.2.4.7.2.1.11
Delay of alarm condition
Status: mandatory	Access: read-write
OBJECT-TYPE
	INTEGER

cmcTcUnit3TypeOfDevice		1.3.6.1.4.1.2606.4.2.5.1
Type of sensor unit connected to port 3
Status: mandatory	Access: read-only
OBJECT-TYPE
	INTEGER	notAvail(1), unitIO(2), unitAccess(3), unitClimate(4), unitFCS(5), unitRTT(6), unitRCT(7), unitPSM(8), unitPSM8(9), unitPSMMetered(10), unitIOWireless(11), unitPSM6Schuko(12), unitPSM6C19(13), unitFuelCell(14), unitDRC(15), unitTECooler(16), unitPSMMetered32(17), unitPSM8x8(18), unitPSM6x6Schuko(19), unitPSM6x6C19(20)

cmcTcUnit3Text		1.3.6.1.4.1.2606.4.2.5.2
Descriptional text for sensor unit connected to port 3
Status: mandatory	Access: read-write
OBJECT-TYPE
	DisplayString	Size(0..10)

cmcTcUnit3Serial		1.3.6.1.4.1.2606.4.2.5.3
Serialnumber of sensor unit connected to port 3
Status: mandatory	Access: read-only
OBJECT-TYPE
	INTEGER

cmcTcUnit3Status		1.3.6.1.4.1.2606.4.2.5.4
General Status sensor unit connected to port 3 (1) OK (2) error, e. g. value overflow (3) configuration of sensor unit has changed, confirmation required (4) Quit from sensor unit to confirm configuration changes (5) timeout of sensor unit, confirmation required to unload this unit (6) sensor unit detected, needs to be confirmed (7) unit is not available (8) supply voltage is too low (9) Firmware upgrade running
Status: mandatory	Access: read-only
OBJECT-TYPE
	INTEGER	ok(1), error(2), changed(3), quit(4), timeout(5), detected(6), notAvail(7), lowPower(8), fwUpgrade(9)

cmcTcUnit3NumberOfSensors		1.3.6.1.4.1.2606.4.2.5.5.1
Number of sensors connected to sensor unit 3
Status: mandatory	Access: read-only
OBJECT-TYPE
	INTEGER

cmcTcUnit3SensorTable		1.3.6.1.4.1.2606.4.2.5.5.2
Headline of sensor table
Status: mandatory	Access: not-accessible
OBJECT-TYPE
	SEQUENCE OF
		CmcTcUnit3SensorEntry

cmcTcUnit3SensorEntry		1.3.6.1.4.1.2606.4.2.5.5.2.1
Entries of sensor table
Status: mandatory	Access: not-accessible
OBJECT-TYPE
	CmcTcUnit3SensorEntry

unit3SensorIndex		1.3.6.1.4.1.2606.4.2.5.5.2.1.1
Index for the list of value entries. Its value ranges between 1 and the value of cmcTcUnit3NumberOfSensors.
Status: mandatory	Access: read-only
OBJECT-TYPE
	INTEGER	1..65535

unit3SensorType		1.3.6.1.4.1.2606.4.2.5.5.2.1.2
Type of sensor which is connected to sensor unit 3 to sensor[unit3SensorIndex] 1: no sensor connected 2: sensor failure 3: value overflow 4: sensor type 1, access sensor 5: sensor type 2, vibration sensor 6: sensor type 3, motion sensor 7: sensor type 4, smoke sensor 8: sensor type 5, air flow sensor 9: sensor type 6, reserved 10: sensor type 7, temperature sensor 11: sensor type 8, 4..20mA sensor 12: sensor type 9, humidity sensor 13: user sensor with normally opened contact 14: user sensor with normally closed contact 15: door locked sensor from locking device 16: remote unlock sensor (e.g. external keypad) 17: voltage sensor, indicates status of main voltage 18: voltage value 19: fan status 20: cardreader or keypad, connected to I2C port 21: duty cycle of fan, FCS-Unit 22: status of fan, FCS-Unit 23: leakage sensor 24: warning, RittalTopTherm(RTT)-Unit 25: alarm, RittalTopTherm-Unit 26: temperature difference filter monitor, RTT-Unit 27: heatflow RCT-Unit 28: alarm RCT-Unit 29: warning RCT-Unit 30: actual current*10, PSM-Unit 31: status PSM-Unit 32: position PSM-Unit, normal/reversed = circuit 1/2 33: air Flap 34: acoustic sensor 35: DET-AC fault (extinguisher) 36: DET-AC first alarm (extinguisher) 37: DET-AC main alarm (extinguisher) 38: DRC: RFID Tag 40-47: RPM Fan 1.1 - Fan 4.2, LCP 48-55: Air temperature 1.1 - 4.2, LCP 56,57: actual temperature 1,2, LCP 58: water inlet temperature, LCP 59: water outlet temperature, LCP 60: water flow 61: fan speed (desired value) 62: status valve, LCP 63: status LCP 64: temperature difference water temperatures 65: control temperature 1, LCP 66: control temperature 2, LCP 67: condensate pump, duration, LCP 68: condensate pump, cycles, LCP 72: total energy*10 (kWh), PSM 73: total power*10 (kW), PSM 74: frequency*10 (Hz), PSM 75: voltage*10 (V), PSM 76: voltage status, PSM 77: current*10 (A), PSM 78: current status, PSM 79: power*10 (kW) per phase, PSM 80: energy*10 (kWh) per phase, PSM 81: temporary energy*10 (kWh) per phase, PSM 100: temperature sensor, wireless 101: temperature sensor (combi), wireless 102: humidity sensor, wireless 103: access sensor, wireless 104: user sensor with normally opened contact, wireless 105: user sensor with normally closed contact, wireless 106: analog sensor 4..20mA, wireless
Status: mandatory	Access: read-only
OBJECT-TYPE
	INTEGER	notAvail(1), failure(2), overflow(3), access(4), vibration(5), motion(6), smoke(7), airFlow(8), type6(9), temperature(10), current4to20(11), humidity(12), userNO(13), userNC(14), lock(15), unlock(16), voltOK(17), voltage(18), fanOK(19), readerKeypad(20), dutyPWM(21), fanStatus(22), leakage(23), warningRTT(24), alarmRTT(25), filterRTT(26), heatflowRCT(27), alarmRCT(28), warningRCT(29), currentPSM(30), statusPSM(31), positionPSM(32), airFlap(33), acoustic(34), detACfault(35), detACfirstAlarm(36), detACmainAlarm(37), rfidTag(38), rpm11LCP(40), rpm12LCP(41), rpm21LCP(42), rpm22LCP(43), rpm31LCP(44), rpm32LCP(45), rpm41LCP(46), rpm42LCP(47), airTemp11LCP(48), airTemp12LCP(49), airTemp21LCP(50), airTemp22LCP(51), airTemp31LCP(52), airTemp32LCP(53), airTemp41LCP(54), airTemp42LCP(55), temp1LCP(56), temp2LCP(57), waterInTemp(58), waterOutTemp(59), waterFlow(60), fanSpeed(61), valve(62), statusLCP(63), waterDelta(64), valveActual(65), contrTemp2(66), condensateDuration(67), condensateCycles(68), totalKWhPSM(72), totalKWPSM(73), frequencyPSM(74), voltagePSM(75), voltStatusPSM(76), amperePSM(77), ampStatusPSM(78), kWPSM(79), kWhPSM(80), kWhTempPSM(81), temperatureWL(100), temperature1WL(101), humidityWL(102), accessWL(103), userNOWL(104), userNCWL(105), analogWL(106)

unit3SensorText		1.3.6.1.4.1.2606.4.2.5.5.2.1.3
Descriptional text for each sensor (entry in the table)
Status: mandatory	Access: read-write
OBJECT-TYPE
	DisplayString	Size(0..20)

unit3SensorStatus		1.3.6.1.4.1.2606.4.2.5.5.2.1.4
Actual status of the sensor
Status: mandatory	Access: read-only
OBJECT-TYPE
	INTEGER	notAvail(1), lost(2), changed(3), ok(4), off(5), on(6), warning(7), tooLow(8), tooHigh(9), error(10)

unit3SensorValue		1.3.6.1.4.1.2606.4.2.5.5.2.1.5
Value of sensor
Status: mandatory	Access: read-only
OBJECT-TYPE
	INTEGER

unit3SensorSetHigh		1.3.6.1.4.1.2606.4.2.5.5.2.1.6
Value for high setpoint of sensor
Status: mandatory	Access: read-write
OBJECT-TYPE
	INTEGER

unit3SensorSetLow		1.3.6.1.4.1.2606.4.2.5.5.2.1.7
Value for low setpoint of sensor
Status: mandatory	Access: read-write
OBJECT-TYPE
	INTEGER

unit3SensorSetWarn		1.3.6.1.4.1.2606.4.2.5.5.2.1.8
Value for warning setpoint of sensor, also used as fan threshold
Status: mandatory	Access: read-write
OBJECT-TYPE
	INTEGER

unit3SensorHysteresis		1.3.6.1.4.1.2606.4.2.5.5.2.1.9
% -Value for hysteresis for High, Low and Warning, input in % from actual setpoint
Status: mandatory	Access: read-write
OBJECT-TYPE
	INTEGER

unit3SensorDisplayFactor		1.3.6.1.4.1.2606.4.2.5.5.2.1.10
Factor of sensor value and setpoints, devide actual value with this value, e. g. factor = 10: sensor value = 100, actual value = 10.0
Status: mandatory	Access: read-only
OBJECT-TYPE
	INTEGER

unit3SensorScaleStart		1.3.6.1.4.1.2606.4.2.5.5.2.1.11
Value for start value for scaling of 0..100% (4..20mA) sensor, example: acutal range of value of 4..20mA sensor is from 10 to 60A, then this variable is set to 10, also valid for setpoints
Status: mandatory	Access: read-write
OBJECT-TYPE
	INTEGER

unit3SensorScaleEnd		1.3.6.1.4.1.2606.4.2.5.5.2.1.12
Value for end value for scaling of 0..100% (4..20mA) sensor, example: acutal range of value of 4..20mA sensor is from 10 to 60A, then this variable is set to 60, also valid for setpoints
Status: mandatory	Access: read-write
OBJECT-TYPE
	INTEGER

unit3SensorUnit		1.3.6.1.4.1.2606.4.2.5.5.2.1.13
Unit for 0..100% (4..20mA) sensor, example: acutal range of value of 4..20mA sensor is from 10 to 60A, then this variable is set to 'A'
Status: mandatory	Access: read-write
OBJECT-TYPE
	DisplayString	Size(0..10)

unit3SensorInfo		1.3.6.1.4.1.2606.4.2.5.5.2.1.14
Additional information to the sensor, e. g. Serialnumber, Signal Quality..
Status: mandatory	Access: read-only
OBJECT-TYPE
	DisplayString	Size(0..50)

cmcTcUnit3NumberOfOutputs		1.3.6.1.4.1.2606.4.2.5.6.1
Number of outputs available on sensor unit 3
Status: mandatory	Access: read-only
OBJECT-TYPE
	INTEGER

cmcTcUnit3OutputTable		1.3.6.1.4.1.2606.4.2.5.6.2
Headline of output table
Status: mandatory	Access: not-accessible
OBJECT-TYPE
	SEQUENCE OF
		CmcTcUnit3OutputEntry

cmcTcUnit3OutputEntry		1.3.6.1.4.1.2606.4.2.5.6.2.1
Entries of output table
Status: mandatory	Access: not-accessible
OBJECT-TYPE
	CmcTcUnit3OutputEntry

unit3OutputIndex		1.3.6.1.4.1.2606.4.2.5.6.2.1.1
Index for the list of output entries. Its value ranges between 1 and the value of cmcTcUnit3NumberOfOutputs.
Status: mandatory	Access: read-only
OBJECT-TYPE
	INTEGER	1..65535

unit3OutputType		1.3.6.1.4.1.2606.4.2.5.6.2.1.2
Type of output which is connected to sensor unit 3 to output[unit3OutputIndex] 1: no output connected 2: output failure 3: value overflow 4: output type 1, door locking TS8,Ergoform 5: output type 2, universal lock 1, lock with power 6: output type 3, universal lock 2, unlock with power 7: output type 4, fan relay 8: output type 5, fan controlled 9: output type 6, universal relay output 10: output type 7, room door lock 11: output type 8, power output 12: output type 9, door lock with Master key 13: output type 10, door lock FR(i) 14: setpoint (FCS, RTT) 15: setpoint temperature monitoring (RTT) 16: hysteresis of setpoint (RCT) 17: command for remote control of RCT 18: relay PSM, 1=On, 0=Off 19: high setpoint current monitoring PSM 20: low setpoint current monitoring PSM 21: setpoint temperature RTT 22: setpoint temperature monitoring RTT 23: power output 20A 24: door magnet (automatic door release) 30: control mode LCP 31: min fan speed (fan control) LCP 32: min delta T (fan control) LCP 33: max delta T (fan control) LCP 34: PID controller, KP, LCP 35: PID controller, KI, LCP 36 PID controller, KD, LCP 37 flowrate flowmeter, LCP 38: cw value of water (default: 4187) LCP 39: deltaT, LCP 40: control mode, LCP 42: setpoint high voltage PSM 43: setpoint low voltage PSM 44: setpoint high current PSM 45: setpoint low current PSM 46: command PSM
Status: mandatory	Access: read-only
OBJECT-TYPE
	INTEGER	notAvail(1), failure(2), overflow(3), doorLock(4), univLock1(5), univLock2(6), fan(7), fanSpeedContr(8), universalOut(9), roomLock(10), powerOut(11), doorLockMaster(12), doorLockFRi(13), setpoint(14), setpointTimax(15), hysteresisRCT(16), commandRCT(17), relayPSM(18), setHighPSM(19), setLowPSM(20), setpointRTT(21), setTimaxRTT(22), powerOut1(23), doorMagnet(24), controlModeLCP(30), minFanSpeedLCP(31), minDeltaTLCP(32), maxDeltaTLCP(33), kPLCP(34), kILCP(35), kDLCP(36), flowRateLCP(37), cwValueLCP(38), deltaTLCP(39), ctrModLCP(40), voltHighPSM(42), voltLowPSM(43), ampHighPSM(44), ampLowPSM(45), commandPSM(46)

unit3OutputText		1.3.6.1.4.1.2606.4.2.5.6.2.1.3
Descriptional text for each output (entry in the table)
Status: mandatory	Access: read-write
OBJECT-TYPE
	DisplayString	Size(0..20)

unit3OutputStatus		1.3.6.1.4.1.2606.4.2.5.6.2.1.4
Actual status of the output
Status: mandatory	Access: read-write
OBJECT-TYPE
	INTEGER	notAvail(1), lost(2), changed(3), ok(4), off(5), on(6), setOff(7), setOn(8)

unit3OutputValue		1.3.6.1.4.1.2606.4.2.5.6.2.1.5
Value for output
Status: mandatory	Access: read-write
OBJECT-TYPE
	INTEGER

unit3OutputSet		1.3.6.1.4.1.2606.4.2.5.6.2.1.6
Command for output
Status: mandatory	Access: read-write
OBJECT-TYPE
	INTEGER	off(1), on(2), lock(3), unlock(4), unlockDelay(5)

unit3OutputConfig		1.3.6.1.4.1.2606.4.2.5.6.2.1.7
Configuration for output 1: disable remote control (e.g. keypad) 2: enable remote control
Status: mandatory	Access: read-write
OBJECT-TYPE
	INTEGER	disRemote(1), enRemote(2)

unit3OutputDelay		1.3.6.1.4.1.2606.4.2.5.6.2.1.8
Unsigned Value for delay, after this time the output will fall into the previous state
Status: mandatory	Access: read-write
OBJECT-TYPE
	INTEGER

unit3OutputTimeoutAction		1.3.6.1.4.1.2606.4.2.5.6.2.1.9
State for output if timeout (RS422) occurs
Status: mandatory	Access: read-write
OBJECT-TYPE
	INTEGER	stay(1), off(2), on(3)

cmcTcUnit3NumberOfMsgs		1.3.6.1.4.1.2606.4.2.5.7.1
Number of alarms that can be created with sensor unit 3
Status: mandatory	Access: read-only
OBJECT-TYPE
	INTEGER

cmcTcUnit3MsgTable		1.3.6.1.4.1.2606.4.2.5.7.2
Headline of message table
Status: mandatory	Access: not-accessible
OBJECT-TYPE
	SEQUENCE OF
		CmcTcUnit3MsgEntry

cmcTcUnit3MsgEntry		1.3.6.1.4.1.2606.4.2.5.7.2.1
Entries of message table
Status: mandatory	Access: not-accessible
OBJECT-TYPE
	CmcTcUnit3MsgEntry

unit3MsgIndex		1.3.6.1.4.1.2606.4.2.5.7.2.1.1
Index for the list of alarm entries. Its value ranges between 1 and the value of cmcTcUnit3NumberOfMsgs.
Status: mandatory	Access: read-only
OBJECT-TYPE
	INTEGER	1..65535

unit3MsgText		1.3.6.1.4.1.2606.4.2.5.7.2.1.2
Descriptional text for each message (entry in the table)
Status: mandatory	Access: read-write
OBJECT-TYPE
	DisplayString	Size(0..20)

unit3MsgStatus		1.3.6.1.4.1.2606.4.2.5.7.2.1.3
Actual message status 1: not available 2: configuration has changed (sensor new, changed, lost) 3: error 4: OK 5: alarm, e.g. smoke, vibration... 6: warning of analog value, value reached warning threshold 7: analog value too low, value reached low threshold 8: analog value too high, value reached high threshold 9: output is set to OFF 10: output is set to ON 11: door is open 12: door is closed 13: door is locked 14: door is unlocked by remote input, e.g. external cardreader 15: door is unlocked by reader or keypad connected to I2C 16: door is unlocked by SNMP set command (unit1OutputSet) 17: door is unlocked by WEB 18: door is unlocked by timer 19: no access, wrong keycode or cardnumber 20: orientation of PSM-Unit is circuit 1 21: orientation of PSM-Unit is circuit 2 22: battery low, wireless sensor
Status: mandatory	Access: read-only
OBJECT-TYPE
	INTEGER	notAvail(1), configChanged(2), error(3), ok(4), alarm(5), warning(6), tooLow(7), tooHigh(8), setOff(9), setOn(10), open(11), closed(12), locked(13), unlRemote(14), unlReaderKeypad(15), unlSNMP(16), unlWEB(17), unlTimer(18), noAccess(19), circuit1(20), circuit2(21), lowBatt(22)

unit3MsgRelay		1.3.6.1.4.1.2606.4.2.5.7.2.1.4
Setup of Alarm relay for this alarm 1: no switching of alarm relay 2: switching of alarm relay
Status: mandatory	Access: read-write
OBJECT-TYPE
	INTEGER	disable(1), enable(2)

unit3MsgBeeper		1.3.6.1.4.1.2606.4.2.5.7.2.1.5
Setup of Alarm beeper for this alarm 1: no audible alarm 2: audible alarm
Status: mandatory	Access: read-write
OBJECT-TYPE
	INTEGER	disable(1), enable(2)

unit3MsgTrap1		1.3.6.1.4.1.2606.4.2.5.7.2.1.6
Trap receiver 1 activated
Status: mandatory	Access: read-write
OBJECT-TYPE
	INTEGER	disable(1), enable(2)

unit3MsgTrap2		1.3.6.1.4.1.2606.4.2.5.7.2.1.7
Trap receiver 2 activated
Status: mandatory	Access: read-write
OBJECT-TYPE
	INTEGER	disable(1), enable(2)

unit3MsgTrap3		1.3.6.1.4.1.2606.4.2.5.7.2.1.8
Trap receiver 3 activated
Status: mandatory	Access: read-write
OBJECT-TYPE
	INTEGER	disable(1), enable(2)

unit3MsgTrap4		1.3.6.1.4.1.2606.4.2.5.7.2.1.9
Trap receiver 4 and Event Logging activated
Status: mandatory	Access: read-write
OBJECT-TYPE
	INTEGER	disable(1), enable(2)

unit3MsgQuit		1.3.6.1.4.1.2606.4.2.5.7.2.1.10
Reset of this alarm 1: auto 2: manual, alarm needs confirmation, e. g. with 'C' key
Status: mandatory	Access: read-write
OBJECT-TYPE
	INTEGER	auto(1), manual(2)

unit3MsgDelay		1.3.6.1.4.1.2606.4.2.5.7.2.1.11
Delay of alarm condition
Status: mandatory	Access: read-write
OBJECT-TYPE
	INTEGER

cmcTcUnit4TypeOfDevice		1.3.6.1.4.1.2606.4.2.6.1
Type of sensor unit connected to port 4
Status: mandatory	Access: read-only
OBJECT-TYPE
	INTEGER	notAvail(1), unitIO(2), unitAccess(3), unitClimate(4), unitFCS(5), unitRTT(6), unitRCT(7), unitPSM(8), unitPSM8(9), unitPSMMetered(10), unitIOWireless(11), unitPSM6Schuko(12), unitPSM6C19(13), unitFuelCell(14), unitDRC(15), unitTECooler(16), unitPSMMetered32(17), unitPSM8x8(18), unitPSM6x6Schuko(19), unitPSM6x6C19(20)

cmcTcUnit4Text		1.3.6.1.4.1.2606.4.2.6.2
Descriptional text for sensor unit connected to port 4
Status: mandatory	Access: read-write
OBJECT-TYPE
	DisplayString	Size(0..10)

cmcTcUnit4Serial		1.3.6.1.4.1.2606.4.2.6.3
Serialnumber of sensor unit connected to port 4
Status: mandatory	Access: read-only
OBJECT-TYPE
	INTEGER

cmcTcUnit4Status		1.3.6.1.4.1.2606.4.2.6.4
General Status sensor unit connected to port 4 (1) OK (2) error, e. g. value overflow (3) configuration of sensor unit has changed, confirmation required (4) Quit from sensor unit to confirm configuration changes (5) timeout of sensor unit, confirmation required to unload this unit (6) sensor unit detected, needs to be confirmed (7) unit is not available (8) supply voltage is too low (9) Firmware upgrade running
Status: mandatory	Access: read-only
OBJECT-TYPE
	INTEGER	ok(1), error(2), changed(3), quit(4), timeout(5), detected(6), notAvail(7), lowPower(8), fwUpgrade(9)

cmcTcUnit4NumberOfSensors		1.3.6.1.4.1.2606.4.2.6.5.1
Number of sensors connected to sensor unit 4
Status: mandatory	Access: read-only
OBJECT-TYPE
	INTEGER

cmcTcUnit4SensorTable		1.3.6.1.4.1.2606.4.2.6.5.2
Headline of sensor table
Status: mandatory	Access: not-accessible
OBJECT-TYPE
	SEQUENCE OF
		CmcTcUnit4SensorEntry

cmcTcUnit4SensorEntry		1.3.6.1.4.1.2606.4.2.6.5.2.1
Entries of sensor table
Status: mandatory	Access: not-accessible
OBJECT-TYPE
	CmcTcUnit4SensorEntry

unit4SensorIndex		1.3.6.1.4.1.2606.4.2.6.5.2.1.1
Index for the list of value entries. Its value ranges between 1 and the value of cmcTcUnit4NumberOfSensors.
Status: mandatory	Access: read-only
OBJECT-TYPE
	INTEGER	1..65535

unit4SensorType		1.3.6.1.4.1.2606.4.2.6.5.2.1.2
Type of sensor which is connected to sensor unit 4 to sensor[unit4SensorIndex] 1: no sensor connected 2: sensor failure 3: value overflow 4: sensor type 1, access sensor 5: sensor type 2, vibration sensor 6: sensor type 3, motion sensor 7: sensor type 4, smoke sensor 8: sensor type 5, air flow sensor 9: sensor type 6, reserved 10: sensor type 7, temperature sensor 11: sensor type 8, 4..20mA sensor 12: sensor type 9, humidity sensor 13: user sensor with normally opened contact 14: user sensor with normally closed contact 15: door locked sensor from locking device 16: remote unlock sensor (e.g. external keypad) 17: voltage sensor, indicates status of main voltage 18: voltage value 19: fan status 20: cardreader or keypad, connected to I2C port 21: duty cycle of fan, FCS-Unit 22: status of fan, FCS-Unit 23: leakage sensor 24: warning, RittalTopTherm(RTT)-Unit 25: alarm, RittalTopTherm-Unit 26: temperature difference filter monitor, RTT-Unit 27: heatflow RCT-Unit 28: alarm RCT-Unit 29: warning RCT-Unit 30: actual current*10, PSM-Unit 31: status PSM-Unit 32: position PSM-Unit, normal/reversed = circuit 1/2 33: air Flap 34: acoustic sensor 35: DET-AC fault (extinguisher) 36: DET-AC first alarm (extinguisher) 37: DET-AC main alarm (extinguisher) 38: DRC: RFID Tag 40-47: RPM Fan 1.1 - Fan 4.2, LCP 48-55: Air temperature 1.1 - 4.2, LCP 56,57: actual temperature 1,2, LCP 58: water inlet temperature, LCP 59: water outlet temperature, LCP 60: water flow 61: fan speed (desired value) 62: status valve, LCP 63: status LCP 64: temperature difference water temperatures 65: control temperature 1, LCP 66: control temperature 2, LCP 67: condensate pump, duration, LCP 68: condensate pump, cycles, LCP 72: total energy*10 (kWh), PSM 73: total power*10 (kW), PSM 74: frequency*10 (Hz), PSM 75: voltage*10 (V), PSM 76: voltage status, PSM 77: current*10 (A), PSM 78: current status, PSM 79: power*10 (kW) per phase, PSM 80: energy*10 (kWh) per phase, PSM 81: temporary energy*10 (kWh) per phase, PSM 100: temperature sensor, wireless 101: temperature sensor (combi), wireless 102: humidity sensor, wireless 103: access sensor, wireless 104: user sensor with normally opened contact, wireless 105: user sensor with normally closed contact, wireless 106: analog sensor 4..20mA, wireless
Status: mandatory	Access: read-only
OBJECT-TYPE
	INTEGER	notAvail(1), failure(2), overflow(3), access(4), vibration(5), motion(6), smoke(7), airFlow(8), type6(9), temperature(10), current4to20(11), humidity(12), userNO(13), userNC(14), lock(15), unlock(16), voltOK(17), voltage(18), fanOK(19), readerKeypad(20), dutyPWM(21), fanStatus(22), leakage(23), warningRTT(24), alarmRTT(25), filterRTT(26), heatflowRCT(27), alarmRCT(28), warningRCT(29), currentPSM(30), statusPSM(31), positionPSM(32), airFlap(33), acoustic(34), detACfault(35), detACfirstAlarm(36), detACmainAlarm(37), rfidTag(38), rpm11LCP(40), rpm12LCP(41), rpm21LCP(42), rpm22LCP(43), rpm31LCP(44), rpm32LCP(45), rpm41LCP(46), rpm42LCP(47), airTemp11LCP(48), airTemp12LCP(49), airTemp21LCP(50), airTemp22LCP(51), airTemp31LCP(52), airTemp32LCP(53), airTemp41LCP(54), airTemp42LCP(55), temp1LCP(56), temp2LCP(57), waterInTemp(58), waterOutTemp(59), waterFlow(60), fanSpeed(61), valve(62), statusLCP(63), waterDelta(64), valveActual(65), contrTemp2(66), condensateDuration(67), condensateCycles(68), totalKWhPSM(72), totalKWPSM(73), frequencyPSM(74), voltagePSM(75), voltStatusPSM(76), amperePSM(77), ampStatusPSM(78), kWPSM(79), kWhPSM(80), kWhTempPSM(81), temperatureWL(100), temperature1WL(101), humidityWL(102), accessWL(103), userNOWL(104), userNCWL(105), analogWL(106)

unit4SensorText		1.3.6.1.4.1.2606.4.2.6.5.2.1.3
Descriptional text for each sensor (entry in the table)
Status: mandatory	Access: read-write
OBJECT-TYPE
	DisplayString	Size(0..20)

unit4SensorStatus		1.3.6.1.4.1.2606.4.2.6.5.2.1.4
Actual status of the sensor
Status: mandatory	Access: read-only
OBJECT-TYPE
	INTEGER	notAvail(1), lost(2), changed(3), ok(4), off(5), on(6), warning(7), tooLow(8), tooHigh(9), error(10)

unit4SensorValue		1.3.6.1.4.1.2606.4.2.6.5.2.1.5
Value of sensor
Status: mandatory	Access: read-only
OBJECT-TYPE
	INTEGER

unit4SensorSetHigh		1.3.6.1.4.1.2606.4.2.6.5.2.1.6
Value for high setpoint of sensor
Status: mandatory	Access: read-write
OBJECT-TYPE
	INTEGER

unit4SensorSetLow		1.3.6.1.4.1.2606.4.2.6.5.2.1.7
Value for low setpoint of sensor
Status: mandatory	Access: read-write
OBJECT-TYPE
	INTEGER

unit4SensorSetWarn		1.3.6.1.4.1.2606.4.2.6.5.2.1.8
Value for warning setpoint of sensor, also used as fan threshold
Status: mandatory	Access: read-write
OBJECT-TYPE
	INTEGER

unit4SensorHysteresis		1.3.6.1.4.1.2606.4.2.6.5.2.1.9
% -Value for hysteresis for High, Low and Warning, input in % from actual setpoint
Status: mandatory	Access: read-write
OBJECT-TYPE
	INTEGER

unit4SensorDisplayFactor		1.3.6.1.4.1.2606.4.2.6.5.2.1.10
Factor of sensor value and setpoints, devide actual value with this value, e. g. factor = 10: sensor value = 100, actual value = 10.0
Status: mandatory	Access: read-only
OBJECT-TYPE
	INTEGER

unit4SensorScaleStart		1.3.6.1.4.1.2606.4.2.6.5.2.1.11
Value for start value for scaling of 0..100% (4..20mA) sensor, example: acutal range of value of 4..20mA sensor is from 10 to 60A, then this variable is set to 10, also valid for setpoints
Status: mandatory	Access: read-write
OBJECT-TYPE
	INTEGER

unit4SensorScaleEnd		1.3.6.1.4.1.2606.4.2.6.5.2.1.12
Value for end value for scaling of 0..100% (4..20mA) sensor, example: acutal range of value of 4..20mA sensor is from 10 to 60A, then this variable is set to 60, also valid for setpoints
Status: mandatory	Access: read-write
OBJECT-TYPE
	INTEGER

unit4SensorUnit		1.3.6.1.4.1.2606.4.2.6.5.2.1.13
Unit for 0..100% (4..20mA) sensor, example: acutal range of value of 4..20mA sensor is from 10 to 60A, then this variable is set to 'A'
Status: mandatory	Access: read-write
OBJECT-TYPE
	DisplayString	Size(0..10)

unit4SensorInfo		1.3.6.1.4.1.2606.4.2.6.5.2.1.14
Additional information to the sensor, e. g. Serialnumber, Signal Quality..
Status: mandatory	Access: read-only
OBJECT-TYPE
	DisplayString	Size(0..50)

cmcTcUnit4NumberOfOutputs		1.3.6.1.4.1.2606.4.2.6.6.1
Number of outputs available on sensor unit 4
Status: mandatory	Access: read-only
OBJECT-TYPE
	INTEGER

cmcTcUnit4OutputTable		1.3.6.1.4.1.2606.4.2.6.6.2
Headline of output table
Status: mandatory	Access: not-accessible
OBJECT-TYPE
	SEQUENCE OF
		CmcTcUnit4OutputEntry

cmcTcUnit4OutputEntry		1.3.6.1.4.1.2606.4.2.6.6.2.1
Entries of output table
Status: mandatory	Access: not-accessible
OBJECT-TYPE
	CmcTcUnit4OutputEntry

unit4OutputIndex		1.3.6.1.4.1.2606.4.2.6.6.2.1.1
Index for the list of output entries. Its value ranges between 1 and the value of cmcTcUnit4NumberOfOutputs.
Status: mandatory	Access: read-only
OBJECT-TYPE
	INTEGER	1..65535

unit4OutputType		1.3.6.1.4.1.2606.4.2.6.6.2.1.2
Type of output which is connected to sensor unit 4 to output[unit4OutputIndex] 1: no output connected 2: output failure 3: value overflow 4: output type 1, door locking TS8,Ergoform 5: output type 2, universal lock 1, lock with power 6: output type 3, universal lock 2, unlock with power 7: output type 4, fan relay 8: output type 5, fan controlled 9: output type 6, universal relay output 10: output type 7, room door lock 11: output type 8, power output 12: output type 9, door lock with Master key 13: output type 10, door lock FR(i) 14: setpoint (FCS, RTT) 15: setpoint temperature monitoring (RTT) 16: hysteresis of setpoint (RCT) 17: command for remote control of RCT 18: relay PSM, 1=On, 0=Off 19: high setpoint current monitoring PSM 20: low setpoint current monitoring PSM 21: setpoint temperature RTT 22: setpoint temperature monitoring RTT 23: power output 20A 24: door magnet (automatic door release) 30: control mode LCP 31: min fan speed (fan control) LCP 32: min delta T (fan control) LCP 33: max delta T (fan control) LCP 34: PID controller, KP, LCP 35: PID controller, KI, LCP 36 PID controller, KD, LCP 37 flowrate flowmeter, LCP 38: cw value of water (default: 4187) LCP 39: deltaT, LCP 40: control mode, LCP 42: setpoint high voltage PSM 43: setpoint low voltage PSM 44: setpoint high current PSM 45: setpoint low current PSM 46: command PSM
Status: mandatory	Access: read-only
OBJECT-TYPE
	INTEGER	notAvail(1), failure(2), overflow(3), doorLock(4), univLock1(5), univLock2(6), fan(7), fanSpeedContr(8), universalOut(9), roomLock(10), powerOut(11), doorLockMaster(12), doorLockFRi(13), setpoint(14), setpointTimax(15), hysteresisRCT(16), commandRCT(17), relayPSM(18), setHighPSM(19), setLowPSM(20), setpointRTT(21), setTimaxRTT(22), powerOut1(23), doorMagnet(24), controlModeLCP(30), minFanSpeedLCP(31), minDeltaTLCP(32), maxDeltaTLCP(33), kPLCP(34), kILCP(35), kDLCP(36), flowRateLCP(37), cwValueLCP(38), deltaTLCP(39), ctrModLCP(40), voltHighPSM(42), voltLowPSM(43), ampHighPSM(44), ampLowPSM(45), commandPSM(46)

unit4OutputText		1.3.6.1.4.1.2606.4.2.6.6.2.1.3
Descriptional text for each output (entry in the table)
Status: mandatory	Access: read-write
OBJECT-TYPE
	DisplayString	Size(0..20)

unit4OutputStatus		1.3.6.1.4.1.2606.4.2.6.6.2.1.4
Actual status of the output
Status: mandatory	Access: read-write
OBJECT-TYPE
	INTEGER	notAvail(1), lost(2), changed(3), ok(4), off(5), on(6), setOff(7), setOn(8)

unit4OutputValue		1.3.6.1.4.1.2606.4.2.6.6.2.1.5
Value for output
Status: mandatory	Access: read-write
OBJECT-TYPE
	INTEGER

unit4OutputSet		1.3.6.1.4.1.2606.4.2.6.6.2.1.6
Command for output
Status: mandatory	Access: read-write
OBJECT-TYPE
	INTEGER	off(1), on(2), lock(3), unlock(4), unlockDelay(5)

unit4OutputConfig		1.3.6.1.4.1.2606.4.2.6.6.2.1.7
Configuration for output 1: disable remote control (e.g. keypad) 2: enable remote control
Status: mandatory	Access: read-write
OBJECT-TYPE
	INTEGER	disRemote(1), enRemote(2)

unit4OutputDelay		1.3.6.1.4.1.2606.4.2.6.6.2.1.8
Unsigned Value for delay, after this time the output will fall into the previous state
Status: mandatory	Access: read-write
OBJECT-TYPE
	INTEGER

unit4OutputTimeoutAction		1.3.6.1.4.1.2606.4.2.6.6.2.1.9
State for output if timeout (RS422) occurs
Status: mandatory	Access: read-write
OBJECT-TYPE
	INTEGER	stay(1), off(2), on(3)

cmcTcUnit4NumberOfMsgs		1.3.6.1.4.1.2606.4.2.6.7.1
Number of alarms that can be created with sensor unit 4
Status: mandatory	Access: read-only
OBJECT-TYPE
	INTEGER

cmcTcUnit4MsgTable		1.3.6.1.4.1.2606.4.2.6.7.2
Headline of message table
Status: mandatory	Access: not-accessible
OBJECT-TYPE
	SEQUENCE OF
		CmcTcUnit4MsgEntry

cmcTcUnit4MsgEntry		1.3.6.1.4.1.2606.4.2.6.7.2.1
Entries of message table
Status: mandatory	Access: not-accessible
OBJECT-TYPE
	CmcTcUnit4MsgEntry

unit4MsgIndex		1.3.6.1.4.1.2606.4.2.6.7.2.1.1
Index for the list of alarm entries. Its value ranges between 1 and the value of cmcTcUnit4NumberOfMsgs.
Status: mandatory	Access: read-only
OBJECT-TYPE
	INTEGER	1..65535

unit4MsgText		1.3.6.1.4.1.2606.4.2.6.7.2.1.2
Descriptional text for each message (entry in the table)
Status: mandatory	Access: read-write
OBJECT-TYPE
	DisplayString	Size(0..20)

unit4MsgStatus		1.3.6.1.4.1.2606.4.2.6.7.2.1.3
Actual message status 1: not available 2: configuration has changed (sensor new, changed, lost) 3: error 4: OK 5: alarm, e.g. smoke, vibration... 6: warning of analog value, value reached warning threshold 7: analog value too low, value reached low threshold 8: analog value too high, value reached high threshold 9: output is set to OFF 10: output is set to ON 11: door is open 12: door is closed 13: door is locked 14: door is unlocked by remote input, e.g. external cardreader 15: door is unlocked by reader or keypad connected to I2C 16: door is unlocked by SNMP set command (unit1OutputSet) 17: door is unlocked by WEB 18: door is unlocked by timer 19: no access, wrong keycode or cardnumber 20: orientation of PSM-Unit is circuit 1 21: orientation of PSM-Unit is circuit 2 22: battery low, wireless sensor
Status: mandatory	Access: read-only
OBJECT-TYPE
	INTEGER	notAvail(1), configChanged(2), error(3), ok(4), alarm(5), warning(6), tooLow(7), tooHigh(8), setOff(9), setOn(10), open(11), closed(12), locked(13), unlRemote(14), unlReaderKeypad(15), unlSNMP(16), unlWEB(17), unlTimer(18), noAccess(19), circuit1(20), circuit2(21), lowBatt(22)

unit4MsgRelay		1.3.6.1.4.1.2606.4.2.6.7.2.1.4
Setup of Alarm relay for this alarm 1: no switching of alarm relay 2: switching of alarm relay
Status: mandatory	Access: read-write
OBJECT-TYPE
	INTEGER	disable(1), enable(2)

unit4MsgBeeper		1.3.6.1.4.1.2606.4.2.6.7.2.1.5
Setup of Alarm beeper for this alarm 1: no audible alarm 2: audible alarm
Status: mandatory	Access: read-write
OBJECT-TYPE
	INTEGER	disable(1), enable(2)

unit4MsgTrap1		1.3.6.1.4.1.2606.4.2.6.7.2.1.6
Trap receiver 1 activated
Status: mandatory	Access: read-write
OBJECT-TYPE
	INTEGER	disable(1), enable(2)

unit4MsgTrap2		1.3.6.1.4.1.2606.4.2.6.7.2.1.7
Trap receiver 2 activated
Status: mandatory	Access: read-write
OBJECT-TYPE
	INTEGER	disable(1), enable(2)

unit4MsgTrap3		1.3.6.1.4.1.2606.4.2.6.7.2.1.8
Trap receiver 3 activated
Status: mandatory	Access: read-write
OBJECT-TYPE
	INTEGER	disable(1), enable(2)

unit4MsgTrap4		1.3.6.1.4.1.2606.4.2.6.7.2.1.9
Trap receiver 4 and Event Logging activated
Status: mandatory	Access: read-write
OBJECT-TYPE
	INTEGER	disable(1), enable(2)

unit4MsgQuit		1.3.6.1.4.1.2606.4.2.6.7.2.1.10
Reset of this alarm 1: auto 2: manual, alarm needs confirmation, e. g. with 'C' key
Status: mandatory	Access: read-write
OBJECT-TYPE
	INTEGER	auto(1), manual(2)

unit4MsgDelay		1.3.6.1.4.1.2606.4.2.6.7.2.1.11
Delay of alarm condition
Status: mandatory	Access: read-write
OBJECT-TYPE
	INTEGER

cmcTcValuesRelay		1.3.6.1.4.1.2606.4.2.7.1
Setup of Alarm relay for alarm ext. unit(s) 1: no switching of alarm relay 2: switching of alarm relay
Status: mandatory	Access: read-write
OBJECT-TYPE
	INTEGER	disable(1), enable(2)

cmcTcValuesBeeper		1.3.6.1.4.1.2606.4.2.7.2
Setup of Alarm beeper for alarm ext. unit(s) 1: no audible alarm 2: audible alarm
Status: mandatory	Access: read-write
OBJECT-TYPE
	INTEGER	disable(1), enable(2)

cmcTcValuesTrap1		1.3.6.1.4.1.2606.4.2.7.3
Trap receiver 1 activated
Status: mandatory	Access: read-write
OBJECT-TYPE
	INTEGER	disable(1), enable(2)

cmcTcValuesTrap2		1.3.6.1.4.1.2606.4.2.7.4
Trap receiver 2 activated
Status: mandatory	Access: read-write
OBJECT-TYPE
	INTEGER	disable(1), enable(2)

cmcTcValuesTrap3		1.3.6.1.4.1.2606.4.2.7.5
Trap receiver 3 activated
Status: mandatory	Access: read-write
OBJECT-TYPE
	INTEGER	disable(1), enable(2)

cmcTcValuesTrap4		1.3.6.1.4.1.2606.4.2.7.6
Trap receiver 4 and Event Logging activated
Status: mandatory	Access: read-write
OBJECT-TYPE
	INTEGER	disable(1), enable(2)

cmcTcNumberOfValues		1.3.6.1.4.1.2606.4.2.7.7
Number of values availabel on extension units connected to the CMC
Status: mandatory	Access: read-only
OBJECT-TYPE
	INTEGER

cmcTcValuesTable		1.3.6.1.4.1.2606.4.2.7.8
Headline of values-table
Status: mandatory	Access: not-accessible
OBJECT-TYPE
	SEQUENCE OF
		CmcTcValuesEntry

cmcTcValuesEntry		1.3.6.1.4.1.2606.4.2.7.8.1
Entries of values-table
Status: mandatory	Access: not-accessible
OBJECT-TYPE
	CmcTcValuesEntry

valuesIndex		1.3.6.1.4.1.2606.4.2.7.8.1.1
Index for the list of value entries. Its value ranges between 1 and the value of cmcTcNumberOfValues.
Status: mandatory	Access: read-only
OBJECT-TYPE
	INTEGER	1..65535

valuesText		1.3.6.1.4.1.2606.4.2.7.8.1.2
Descriptional text for each value (entry in the table) of the extension card
Status: mandatory	Access: read-write
OBJECT-TYPE
	DisplayString	Size(0..20)

valuesStatus		1.3.6.1.4.1.2606.4.2.7.8.1.3
Actual status of the value of the extension card
Status: mandatory	Access: read-only
OBJECT-TYPE
	INTEGER	notAvail(1), lost(2), changed(3), ok(4), tooLow(5), tooHigh(6), error(7)

valuesValue		1.3.6.1.4.1.2606.4.2.7.8.1.4
Value of sensor
Status: mandatory	Access: read-only
OBJECT-TYPE
	INTEGER

valuesSetHigh		1.3.6.1.4.1.2606.4.2.7.8.1.5
Value for high setpoint of sensor
Status: mandatory	Access: read-write
OBJECT-TYPE
	INTEGER

valuesSetLow		1.3.6.1.4.1.2606.4.2.7.8.1.6
Value for low setpoint of sensor
Status: mandatory	Access: read-write
OBJECT-TYPE
	INTEGER

valuesHysteresis		1.3.6.1.4.1.2606.4.2.7.8.1.7
% -Value for hysteresis for High and Low setpoints, input in % from actual setpoint
Status: mandatory	Access: read-write
OBJECT-TYPE
	INTEGER

cmcTcSetTempUnit		1.3.6.1.4.1.2606.4.3.1.1
Unit of all temperature values and setpoints, Celsius or Fahrenheit
Status: mandatory	Access: read-write
OBJECT-TYPE
	INTEGER	celsius(1), fahrenheit(2)

cmcTcSetBeeper		1.3.6.1.4.1.2606.4.3.1.2
Audible alarm in CMC-TC unit: (2): beeper is on (1): beeper is off (general)
Status: mandatory	Access: read-write
OBJECT-TYPE
	INTEGER	off(1), on(2)

cmcTcQuitRelay		1.3.6.1.4.1.2606.4.3.1.3
Enable or disable acknowledging currently active alarm relay (with 'C' on CMC-TC).
Status: mandatory	Access: read-write
OBJECT-TYPE
	INTEGER	disabled(1), enabled(2)

cmcTcLogicRelay		1.3.6.1.4.1.2606.4.3.1.4
Logic of alarm relay: (1) Relay will pick up in case of an alarm (2) Relay will release in case of an alarm (3) Relay off (general)
Status: mandatory	Access: read-write
OBJECT-TYPE
	INTEGER	closeAtAlarm(1), openAtAlarm(2), off(3)

cmcTcWebAccess		1.3.6.1.4.1.2606.4.3.1.5
Web access via HTTP: (1) view only (2) full Access, read and set (3) Web disabled (general)
Status: mandatory	Access: read-write
OBJECT-TYPE
	INTEGER	viewOnly(1), fullAccess(2), off(3)

cmcTcSetupDate		1.3.6.1.4.1.2606.4.3.1.6
actual Date in format DD.MM.YYYY
Status: mandatory	Access: read-write
OBJECT-TYPE
	DisplayString	Size(0..10)

cmcTcSetupTime		1.3.6.1.4.1.2606.4.3.1.7
actual Time in format HH:MM:SS, HH (0-23), MM (0-59), SS (0-59)
Status: mandatory	Access: read-write
OBJECT-TYPE
	DisplayString	Size(0..8)

cmcTcTimerNumber		1.3.6.1.4.1.2606.4.3.1.8.1
Number of value-table entries=number of outlets available on this unit
Status: mandatory	Access: read-only
OBJECT-TYPE
	INTEGER

cmcTcTimerTable		1.3.6.1.4.1.2606.4.3.1.8.2
Headline of status-table
Status: mandatory	Access: not-accessible
OBJECT-TYPE
	SEQUENCE OF
		CmcTcTimerEntry

cmcTcTimerEntry		1.3.6.1.4.1.2606.4.3.1.8.2.1
Entries of timer-table
Status: mandatory	Access: not-accessible
OBJECT-TYPE
	CmcTcTimerEntry

cmcTcTimerIndex		1.3.6.1.4.1.2606.4.3.1.8.2.1.1
Index for the list of timer entries. Its value ranges between 1 and the value of cmcTcTimerNumber.
Status: mandatory	Access: read-only
OBJECT-TYPE
	INTEGER	1..65535

cmcTcTimerStatus		1.3.6.1.4.1.2606.4.3.1.8.2.1.2
Actual status of the timer
Status: mandatory	Access: read-only
OBJECT-TYPE
	INTEGER	switchedOff(1), switchedOn(2), noTime(3)

cmcTcTimerDayOfWeek		1.3.6.1.4.1.2606.4.3.1.8.2.1.3
Selection of day of week for timer to switch
Status: mandatory	Access: read-write
OBJECT-TYPE
	INTEGER	sun(1), mon(2), tue(3), wed(4), thu(5), fri(6), sat(7), sat-sun(8), mon-fri(9), mon-sun(10)

cmcTcTimeOn		1.3.6.1.4.1.2606.4.3.1.8.2.1.4
Time to switch on current function, Format: HH:MM
Status: mandatory	Access: read-write
OBJECT-TYPE
	DisplayString	Size(0..5)

cmcTcTimeOff		1.3.6.1.4.1.2606.4.3.1.8.2.1.5
Time to switch off current function, Format: HH:MM
Status: mandatory	Access: read-write
OBJECT-TYPE
	DisplayString	Size(0..5)

cmcTcTimeControl		1.3.6.1.4.1.2606.4.3.1.8.2.1.6
Control via RTC
Status: mandatory	Access: read-write
OBJECT-TYPE
	INTEGER	disabled(1), enabled(2)

cmcTcTimerFunction		1.3.6.1.4.1.2606.4.3.1.8.2.1.7
Function which is controlled via timer 1: unlock via keypad 1 on unit 1 or remote input lock 1 is disabled 2: unlock via keypad 2 on unit 1 or remote input lock 2 is disabled 3 unlock via keypad 1 on unit 2 or remote input lock 1 is disabled 4: unlock via keypad 2 on unit 2 or remote input lock 2 is disabled 5: unlock via keypad 1 on unit 3 or remote input lock 1 is disabled 6: unlock via keypad 2 on unit 3 or remote input lock 2 is disabled 7: unlock via keypad 1 on unit 4 or remote input lock 1 is disabled 8: unlock via keypad 2 on unit 4 or remote input lock 2 is disabled 9: Lock of door 1 on unit 1 will be unlocked 10: Lock of door 2 on unit 1 will be unlocked 11: Lock of door 1 on unit 2 will be unlocked 12: Lock of door 2 on unit 2 will be unlocked 13: Lock of door 1 on unit 3 will be unlocked 14: Lock of door 2 on unit 3 will be unlocked 15: Lock of door 1 on unit 4 will be unlocked 16: Lock of door 2 on unit 4 will be unlocked 17-20: sending Traps to this Trap receiver will be disabled 21: sending SMS will be disabled generally 22-25: Scheduled alarm off 26-29: sending SMS to phone number 1..4 will be disabled
Status: mandatory	Access: read-write
OBJECT-TYPE
	INTEGER	disKeypad1-1(1), disKeypad2-1(2), disKeypad1-2(3), disKeypad2-2(4), disKeypad1-3(5), disKeypad2-3(6), disKeypad1-4(7), disKeypad2-4(8), unlDoor1-1(9), unlDoor2-1(10), unlDoor1-2(11), unlDoor2-2(12), unlDoor1-3(13), unlDoor2-3(14), unlDoor1-4(15), unlDoor2-5(16), disTrapRec1(17), disTrapRec2(18), disTrapRec3(19), disTrapRec4(20), disSMS(21), schedule1(22), schedule2(23), schedule3(24), schedule4(25), disSMS1(26), disSMS2(27), disSMS3(28), disSMS4(29)

cmcTcTraptableNumber		1.3.6.1.4.1.2606.4.4.7.1
Number of trapTable entries. The number of trap-receiver
Status: mandatory	Access: read-only
OBJECT-TYPE
	INTEGER

cmcTcTrapTableTable		1.3.6.1.4.1.2606.4.4.7.2
A list of trap-receiver entries
Status: mandatory	Access: not-accessible
OBJECT-TYPE
	SEQUENCE OF
		CmcTcTrapTableEntry

cmcTcTrapTableEntry		1.3.6.1.4.1.2606.4.4.7.2.1
Entries of trapTable
Status: mandatory	Access: not-accessible
OBJECT-TYPE
	CmcTcTrapTableEntry

trapIndex		1.3.6.1.4.1.2606.4.4.7.2.1.1
Index for the trap-receiver-table. Its value ranges between 1 and the value of traptableNumber
Status: mandatory	Access: read-only
OBJECT-TYPE
	INTEGER	1..65535

trapStatus		1.3.6.1.4.1.2606.4.4.7.2.1.2
Enable or disable trap receiver
Status: mandatory	Access: read-write
OBJECT-TYPE
	INTEGER	disabled(1), enabled(2)

trapIPaddress		1.3.6.1.4.1.2606.4.4.7.2.1.3
IP-address of trap-receiver
Status: mandatory	Access: read-write
OBJECT-TYPE
	DisplayString	Size(0..15)

cmcTcQuitUnit		1.3.6.1.4.1.2606.4.5.1
Command to quit (acknowledge) alarms of CMC-TC unit. Setting to 'quit' (2) will have same result as pressing 'C' on Units. Variable is automatically set back to 'noQuit' (1).
Status: mandatory	Access: read-write
OBJECT-TYPE
	INTEGER	noQuit(1), quit(2)

alarmSensorUnit1		1
Alarm of sensor unit 1
TRAP-TYPE

alarmSensorUnit2		2
Alarm of sensor unit 2
TRAP-TYPE

alarmSensorUnit3		3
Alarm of sensor unit 3
TRAP-TYPE

alarmSensorUnit4		4
Alarm of sensor unit 4
TRAP-TYPE

alarmUnit1		5
Alarm of unit 1
TRAP-TYPE

alarmUnit2		6
Alarm of unit 2
TRAP-TYPE

alarmUnit3		7
Alarm of unit 3
TRAP-TYPE

alarmUnit4		8
Alarm of unit 4
TRAP-TYPE

alarmValues		9
Alarm of values measured by external card
TRAP-TYPE

configChanged		10
The configuration of the cmc has changed, this trap is send if new setup is saved. Configuration can be changed by Terminal, Telnet, Web or SNMP *** NOT IMPLEMENTED ***
TRAP-TYPE