RAISECOM-SYSTEM-MIB

File: RAISECOM-SYSTEM-MIB.mib (58638 bytes)

Imported modules

SNMPv2-SMI RAISECOM-BASE-MIB SNMPv2-TC
SWITCH-TC

Imported symbols

MODULE-IDENTITY Unsigned32 Integer32
OBJECT-TYPE raisecomAgent TruthValue
EnableVar TimeStamp TEXTUAL-CONVENTION

Defined Types

ProcessStatus  
Status of the process.
TEXTUAL-CONVENTION    
  INTEGER r-running(1), d-interruptible-sleep(2), s-uninterruptible-sleep(3), t-stopped(4), z-zombie(5), x-dead(6), w-paging(7)  

CPUTimeStamp  
The time in seconds that could represent signed quantities like time delay with respect to some source. The signed integer part is in the first 32 bits and the fraction part is in the last 32 bits.
TEXTUAL-CONVENTION    
  OCTET STRING Size(16)  

RaisecomCPUUtilizationEntry  
SEQUENCE    
  raisecomCPUUtilizationPeriod INTEGER
  raisecomCPUUtilizationCpuIdx INTEGER
  raisecomCPUUtilization INTEGER

RaisecomTotalCPUUtilizationEntry  
SEQUENCE    
  raisecomTotalCPUPeriod INTEGER
  raisecomTotalCPUUtilization INTEGER

RaisecomCPUHistoryEntry  
SEQUENCE    
  raisecomCPUHistoryPeriod INTEGER
  raisecomCPUHistoryIndex INTEGER
  raisecomCPUHistoryCpuIdx INTEGER
  raisecomCPUHistoryUtil INTEGER

RaisecomTotalCPUHistoryEntry  
SEQUENCE    
  raisecomTotalCPUHistoryPeriod INTEGER
  raisecomTotalCPUHistoryIndex INTEGER
  raisecomTotalCPUHistoryUtil INTEGER

RaisecomProcessesEntry  
SEQUENCE    
  raisecomProcessIndex INTEGER
  raisecomProcessPID INTEGER
  raisecomProcessName OCTET STRING
  raisecomProcessRunTimeTotal CPUTimeStamp
  raisecomProcessInvokedTotal INTEGER
  raisecomProcessTimeCreated TimeStamp
  raisecomProcessCurrentPriority INTEGER
  raisecomProcessStatus ProcessStatus

RaisecomProcessStatisticsEntry  
SEQUENCE    
  raisecomProcessStatisticsPeriod INTEGER
  raisecomProcessRunTime CPUTimeStamp
  raisecomProcessUtilization INTEGER

RaisecomDeadProcessesEntry  
SEQUENCE    
  raisecomDeadProcessIndex INTEGER
  raisecomDeadProcessName OCTET STRING
  raisecomDeadProcessPriority INTEGER
  raisecomDeadProcessTimeDelete TimeStamp
  raisecomDeadProcessDeadTimes INTEGER
  raisecomDeadProcessStatus ProcessStatus

RaisecomEndPoolEntry  
SEQUENCE    
  raisecomBasePort INTEGER
  raisecomTotalEndPool INTEGER
  raisecomFreeEndPool INTEGER

PortAlarmEventList  
The low three bits of An OCTET STRING represents an alarm events enabled or existed list on a port, in which each bit represents an alarm event type. the other bits of An OCTET STRING are not used. The figure shown below illustrates the format of an alarm list. 7 6 5 4 3 2 1 0 +-+-+-+-+-+-+-+-+ | | +-+-+-+-+-+-+-+-+ | | | | | | | | | | | | | | | +- none | | | | | | +--- none | | | | | +----- none | | | | +------- none | | | +--------- none | | +----------- not-forwarding | +------------- link-fault +--------------- link-down The link-down bit set 1 represents that link-down event alarm output is enabled on port, OR the link-down bit set 1 represents that link-down event occured on port. The bit represents alarm output enabled in mibs: raisecomAlarmPortSyslogEvList raisecomAlarmPortNotifiesEvList raisecomAlarmPortRelayEvList The bit represents alarm occured in mibs: raisecomAlarmPortEvList .
TEXTUAL-CONVENTION    
  OCTET STRING Size(1)  

RaisecomVoltEntry  
SEQUENCE    
  raisecomVoltIndex INTEGER
  raisecomVoltReference INTEGER
  raisecomVoltValue INTEGER
  raisecomVoltMin INTEGER
  raisecomVoltMax INTEGER
  raisecomVoltTrapEnable EnableVar
  raisecomVoltThresholdLow Integer32
  raisecomVoltThresholdHigh Integer32
  raisecomVoltTrapTimes INTEGER
  raisecomVoltHighTimes INTEGER
  raisecomVoltLowTimes INTEGER

RaisecomAlarmPortEntry  
SEQUENCE    
  raisecomAlarmPortIndex INTEGER
  raisecomAlarmPortSyslogEvList PortAlarmEventList
  raisecomAlarmPortNotifiesEvList PortAlarmEventList
  raisecomAlarmPortRelayEvList PortAlarmEventList
  raisecomAlarmPortEvList PortAlarmEventList

RaisecomAlarmHistEntry  
SEQUENCE    
  raisecomAlarmHistIndex INTEGER
  raisecomAlarmHistStatus INTEGER
  raisecomAlarmHistSource INTEGER
  raisecomAlarmHistDescr OCTET STRING
  raisecomAlarmHistTimestamp INTEGER
  raisecomAlarmHistType INTEGER

RaisecomAlarmCurtEntry  
SEQUENCE    
  raisecomAlarmCurtIndex INTEGER
  raisecomAlarmCurtSource INTEGER
  raisecomAlarmCurtDescr OCTET STRING
  raisecomAlarmCurtTimestamp INTEGER
  raisecomAlarmCurtType INTEGER

Defined Values

raisecomSystem 1.3.6.1.4.1.8886.1.1
raisecom System objects: objects common to all platforms.
MODULE-IDENTITY    

raisecomCpu 1.3.6.1.4.1.8886.1.1.1
raisecom System objects: objects common to all platforms.
MODULE-IDENTITY    

raisecomCPUTrapGroup 1.3.6.1.4.1.8886.1.1.1.1
OBJECT IDENTIFIER    

raisecomCPURisingThreshold 1.3.6.1.4.1.8886.1.1.1.1.1
CPU utilization rising threshold trap transfer.
Status: current Access: read-only
NOTIFICATION-TYPE    

raisecomCPURisingThresholdRecover 1.3.6.1.4.1.8886.1.1.1.1.2
CPU utilization rising threshold return to normal trap transfer.
Status: current Access: read-only
NOTIFICATION-TYPE    

raisecomCPUScalarGroup 1.3.6.1.4.1.8886.1.1.1.2
OBJECT IDENTIFIER    

raisecomCpuTotalProcNum 1.3.6.1.4.1.8886.1.1.1.2.1
Total number of processes.
Status: current Access: read-only
OBJECT-TYPE    
  INTEGER 1..2000  

raisecomCPUHistoryTableSize 1.3.6.1.4.1.8886.1.1.1.2.2
A value configured by the user which specifies the number of reports in the history table.
Status: current Access: read-only
OBJECT-TYPE    
  INTEGER  

raisecomCPUThresholdTrapEnable 1.3.6.1.4.1.8886.1.1.1.2.3
The administration status of the CPU utilization threshold trap.
Status: deprecated Access: read-write
OBJECT-TYPE    
  EnableVar  

raisecomCPURisingThresholdValue 1.3.6.1.4.1.8886.1.1.1.2.4
The percentage rising threshold value configured by the user. The value indicates, if the CPU utilization which rise from raisecomCPUFallingThresholdValue is equal to or above this value for raisecomCPUThresholdInterval duration then send a raisecomCPURisingThreshold notification to the NMS.
Status: current Access: read-write
OBJECT-TYPE    
  INTEGER 2..99  

raisecomCPURecoverThresholdValue 1.3.6.1.4.1.8886.1.1.1.2.5
The percentage falling threshold value configured by the user. The value indicates, if the CPU utilization which fell from raisecomCPURecoverThresholdValue is equal to or below this value for raisecomCPUThresholdInterval duration then send a raisecomCPUFallingThreshold notification to the NMS.
Status: current Access: read-write
OBJECT-TYPE    
  INTEGER 0..98  

raisecomCPUThresholdInterval 1.3.6.1.4.1.8886.1.1.1.2.6
This is an observation interval. The value of this object indicates that the CPU utilization should be above raisecomCPURisingThresholdValue for this duration to send a raisecomCPURisingThreshold notification to the NMS or below raisecomCPUFallingThresholdValue for this duration to send a raisecomCPUFallingThreshold.
Status: current Access: read-write
OBJECT-TYPE    
  INTEGER 5..36000  

raisecomCpuNum 1.3.6.1.4.1.8886.1.1.1.2.7
Total number of cpu.
Status: current Access: read-only
OBJECT-TYPE    
  INTEGER  

raisecomCPUTableGroup 1.3.6.1.4.1.8886.1.1.1.3
OBJECT IDENTIFIER    

raisecomCPUUtilizationGroup 1.3.6.1.4.1.8886.1.1.1.3.1
OBJECT IDENTIFIER    

raisecomCPUUtilizationTable 1.3.6.1.4.1.8886.1.1.1.3.1.1
This table contains information about multi-core CPU utilization.
Status: current Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    RaisecomCPUUtilizationEntry

raisecomCPUUtilizationEntry 1.3.6.1.4.1.8886.1.1.1.3.1.1.1
Information about the CPU utilization.
Status: current Access: not-accessible
OBJECT-TYPE    
  RaisecomCPUUtilizationEntry  

raisecomCPUUtilizationPeriod 1.3.6.1.4.1.8886.1.1.1.3.1.1.1.1
Periods for computing CPU utilization.
Status: current Access: not-accessible
OBJECT-TYPE    
  INTEGER oneSec(1), fiveSec(2), oneMin(3), tenMin(4), twoHour(5)  

raisecomCPUUtilizationCpuIdx 1.3.6.1.4.1.8886.1.1.1.3.1.1.1.2
The cpu core index
Status: current Access: read-only
OBJECT-TYPE    
  INTEGER 0..16  

raisecomCPUUtilization 1.3.6.1.4.1.8886.1.1.1.3.1.1.1.3
CPU busy percentage in the last specified period.
Status: current Access: read-only
OBJECT-TYPE    
  INTEGER  

raisecomTotalCPUUtilizationTable 1.3.6.1.4.1.8886.1.1.1.3.1.2
This table contains information about total CPU utilization.
Status: current Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    RaisecomTotalCPUUtilizationEntry

raisecomTotalCPUUtilizationEntry 1.3.6.1.4.1.8886.1.1.1.3.1.2.1
Description.
Status: current Access: not-accessible
OBJECT-TYPE    
  RaisecomTotalCPUUtilizationEntry  

raisecomTotalCPUPeriod 1.3.6.1.4.1.8886.1.1.1.3.1.2.1.1
Periods for computing CPU utilization.
Status: current Access: not-accessible
OBJECT-TYPE    
  INTEGER oneSec(1), fiveSec(2), oneMin(3), tenMin(4), twoHour(5)  

raisecomTotalCPUUtilization 1.3.6.1.4.1.8886.1.1.1.3.1.2.1.2
CPU busy percentage in the last specified period.
Status: current Access: read-only
OBJECT-TYPE    
  INTEGER 0..10000  

raisecomCPUHistoryTable 1.3.6.1.4.1.8886.1.1.1.3.1.3
This table contains CPU hsitory utilization records.
Status: current Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    RaisecomCPUHistoryEntry

raisecomCPUHistoryEntry 1.3.6.1.4.1.8886.1.1.1.3.1.3.1
CPU history utilization record.
Status: current Access: not-accessible
OBJECT-TYPE    
  RaisecomCPUHistoryEntry  

raisecomCPUHistoryPeriod 1.3.6.1.4.1.8886.1.1.1.3.1.3.1.1
Periods for computing CPU history utilization, the first index of CPU history utilization table.
Status: current Access: not-accessible
OBJECT-TYPE    
  INTEGER fiveSec(1), oneMin(2), tenMin(3), twoHour(4)  

raisecomCPUHistoryIndex 1.3.6.1.4.1.8886.1.1.1.3.1.3.1.2
Process sequence number,the second index of CPU history utilization table.
Status: current Access: not-accessible
OBJECT-TYPE    
  INTEGER  

raisecomCPUHistoryCpuIdx 1.3.6.1.4.1.8886.1.1.1.3.1.3.1.3
The cpu core index
Status: current Access: read-only
OBJECT-TYPE    
  INTEGER 0..16  

raisecomCPUHistoryUtil 1.3.6.1.4.1.8886.1.1.1.3.1.3.1.4
History record of CPU utilization in the specified period.
Status: current Access: read-only
OBJECT-TYPE    
  INTEGER  

raisecomTotalCPUHistoryTable 1.3.6.1.4.1.8886.1.1.1.3.1.4
This table contains CPU hsitory utilization records.
Status: current Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    RaisecomTotalCPUHistoryEntry

raisecomTotalCPUHistoryEntry 1.3.6.1.4.1.8886.1.1.1.3.1.4.1
CPU history utilization record.
Status: current Access: not-accessible
OBJECT-TYPE    
  RaisecomTotalCPUHistoryEntry  

raisecomTotalCPUHistoryPeriod 1.3.6.1.4.1.8886.1.1.1.3.1.4.1.1
Periods for computing CPU history utilization, the first index of CPU history utilization table.
Status: current Access: not-accessible
OBJECT-TYPE    
  INTEGER fiveSec(1), oneMin(2), tenMin(3), twoHour(4)  

raisecomTotalCPUHistoryIndex 1.3.6.1.4.1.8886.1.1.1.3.1.4.1.2
Process sequence number,the second index of CPU history utilization table.
Status: current Access: not-accessible
OBJECT-TYPE    
  INTEGER  

raisecomTotalCPUHistoryUtil 1.3.6.1.4.1.8886.1.1.1.3.1.4.1.3
History record of CPU utilization in the specified period.
Status: current Access: read-only
OBJECT-TYPE    
  INTEGER  

raisecomCPUProcessesGroup 1.3.6.1.4.1.8886.1.1.1.3.2
OBJECT IDENTIFIER    

raisecomProcessesTable 1.3.6.1.4.1.8886.1.1.1.3.2.1
This table contains information about processes.
Status: current Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    RaisecomProcessesEntry

raisecomProcessesEntry 1.3.6.1.4.1.8886.1.1.1.3.2.1.1
Information about processes.
Status: current Access: not-accessible
OBJECT-TYPE    
  RaisecomProcessesEntry  

raisecomProcessIndex 1.3.6.1.4.1.8886.1.1.1.3.2.1.1.1
This object index of processes table.
Status: current Access: read-only
OBJECT-TYPE    
  INTEGER  

raisecomProcessPID 1.3.6.1.4.1.8886.1.1.1.3.2.1.1.2
This object contains the process ID.
Status: current Access: read-only
OBJECT-TYPE    
  INTEGER  

raisecomProcessName 1.3.6.1.4.1.8886.1.1.1.3.2.1.1.3
The name associated with this process.
Status: current Access: read-only
OBJECT-TYPE    
  OCTET STRING Size(1..32)  

raisecomProcessRunTimeTotal 1.3.6.1.4.1.8886.1.1.1.3.2.1.1.4
The amount of time the process occupied, in microseconds.
Status: current Access: read-only
OBJECT-TYPE    
  CPUTimeStamp  

raisecomProcessInvokedTotal 1.3.6.1.4.1.8886.1.1.1.3.2.1.1.5
The number of times since raisecomProcessTimeCreated that the process has been invoked.
Status: current Access: read-only
OBJECT-TYPE    
  INTEGER  

raisecomProcessTimeCreated 1.3.6.1.4.1.8886.1.1.1.3.2.1.1.6
The time when the process was created. The process sequence number and the time when the process was created, uniquely identifies a process.
Status: current Access: read-only
OBJECT-TYPE    
  TimeStamp  

raisecomProcessCurrentPriority 1.3.6.1.4.1.8886.1.1.1.3.2.1.1.7
The current priority at which the process is running.
Status: current Access: read-only
OBJECT-TYPE    
  INTEGER  

raisecomProcessStatus 1.3.6.1.4.1.8886.1.1.1.3.2.1.1.8
The current status of the process.
Status: current Access: read-only
OBJECT-TYPE    
  ProcessStatus  

raisecomProcessStatisticsTable 1.3.6.1.4.1.8886.1.1.1.3.2.2
This table contains statistics information for processes. The first index is raisecomProcessIndex, the second index is raisecomProcessStatisticsPeriod
Status: current Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    RaisecomProcessStatisticsEntry

raisecomProcessStatisticsEntry 1.3.6.1.4.1.8886.1.1.1.3.2.2.1
Statistics information for processes.
Status: current Access: not-accessible
OBJECT-TYPE    
  RaisecomProcessStatisticsEntry  

raisecomProcessStatisticsPeriod 1.3.6.1.4.1.8886.1.1.1.3.2.2.1.1
Periods for process statistics, the second index of process statistics table.
Status: current Access: not-accessible
OBJECT-TYPE    
  INTEGER fiveSec(1), oneMin(2), tenMin(3)  

raisecomProcessRunTime 1.3.6.1.4.1.8886.1.1.1.3.2.2.1.2
Time of the process occupied in the specified period.
Status: current Access: read-only
OBJECT-TYPE    
  CPUTimeStamp  

raisecomProcessUtilization 1.3.6.1.4.1.8886.1.1.1.3.2.2.1.3
This object provides a general idea of how busy a process caused the processor to be over a specified period.
Status: current Access: read-only
OBJECT-TYPE    
  INTEGER  

raisecomDeadProcessesTable 1.3.6.1.4.1.8886.1.1.1.3.2.3
This table contains dead processes information.
Status: current Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    RaisecomDeadProcessesEntry

raisecomDeadProcessesEntry 1.3.6.1.4.1.8886.1.1.1.3.2.3.1
Dead processes information.
Status: current Access: not-accessible
OBJECT-TYPE    
  RaisecomDeadProcessesEntry  

raisecomDeadProcessIndex 1.3.6.1.4.1.8886.1.1.1.3.2.3.1.1
Process sequence number,the index of dead processes table.
Status: current Access: not-accessible
OBJECT-TYPE    
  INTEGER  

raisecomDeadProcessName 1.3.6.1.4.1.8886.1.1.1.3.2.3.1.2
The name associated with this dead process.
Status: current Access: read-only
OBJECT-TYPE    
  OCTET STRING Size(1..32)  

raisecomDeadProcessPriority 1.3.6.1.4.1.8886.1.1.1.3.2.3.1.3
The priority at which the dead process.
Status: current Access: read-only
OBJECT-TYPE    
  INTEGER  

raisecomDeadProcessTimeDelete 1.3.6.1.4.1.8886.1.1.1.3.2.3.1.4
The time when the process was deleted.
Status: current Access: read-only
OBJECT-TYPE    
  TimeStamp  

raisecomDeadProcessDeadTimes 1.3.6.1.4.1.8886.1.1.1.3.2.3.1.5
Times of the process dead.
Status: current Access: read-only
OBJECT-TYPE    
  INTEGER  

raisecomDeadProcessStatus 1.3.6.1.4.1.8886.1.1.1.3.2.3.1.6
The status of the dead process.
Status: current Access: read-only
OBJECT-TYPE    
  ProcessStatus  

raisecomEndPool 1.3.6.1.4.1.8886.1.1.2
raisecom System objects: objects common to all platforms.
MODULE-IDENTITY    

raisecomEndPoolTable 1.3.6.1.4.1.8886.1.1.2.1
A table of drivers Pool on a managed system.
Status: current Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    RaisecomEndPoolEntry

raisecomEndPoolEntry 1.3.6.1.4.1.8886.1.1.2.1.1
An entry in the END driver Pool monitoring table.
Status: current Access: not-accessible
OBJECT-TYPE    
  RaisecomEndPoolEntry  

raisecomBasePort 1.3.6.1.4.1.8886.1.1.2.1.1.1
The port number based 1 of the port for which this entry contains bridge management information.
Status: current Access: not-accessible
OBJECT-TYPE    
  INTEGER  

raisecomTotalEndPool 1.3.6.1.4.1.8886.1.1.2.1.1.2
Indicates the number of mBlks pre-allocated for this END driver.
Status: current Access: read-only
OBJECT-TYPE    
  INTEGER  

raisecomFreeEndPool 1.3.6.1.4.1.8886.1.1.2.1.1.3
Indicates the number of mBlks available in this END driver pool.
Status: current Access: read-only
OBJECT-TYPE    
  INTEGER  

raisecomMemory 1.3.6.1.4.1.8886.1.1.3
raisecom System objects: memory objects.
MODULE-IDENTITY    

raisecomMemoryTrapGroup 1.3.6.1.4.1.8886.1.1.3.1
OBJECT IDENTIFIER    

raisecomMemoryTrap 1.3.6.1.4.1.8886.1.1.3.1.1
Trap transfer when memory utilization upon threshold.
Status: current Access: read-only
NOTIFICATION-TYPE    

raisecomMemoryTrapRecover 1.3.6.1.4.1.8886.1.1.3.1.2
Trap transfer when memory utilization upon thresholdrecover.
Status: current Access: read-only
NOTIFICATION-TYPE    

raisecomMemoryScalarGroup 1.3.6.1.4.1.8886.1.1.3.2
OBJECT IDENTIFIER    

raisecomMemoryTotal 1.3.6.1.4.1.8886.1.1.3.2.1
The total memory of the system for this duration.
Status: current Access: read-only
OBJECT-TYPE    
  INTEGER  

raisecomMemoryAvailable 1.3.6.1.4.1.8886.1.1.3.2.2
The available memory of the system for this duration.
Status: current Access: read-only
OBJECT-TYPE    
  INTEGER  

raisecomMemoryUtil 1.3.6.1.4.1.8886.1.1.3.2.3
The current value of memory utilization for this duration.
Status: current Access: read-only
OBJECT-TYPE    
  OCTET STRING Size(1..8)  

raisecomMemoryTrapEnable 1.3.6.1.4.1.8886.1.1.3.2.4
The switch of memory trap.
Status: deprecated Access: read-write
OBJECT-TYPE    
  EnableVar  

raisecomMemoryThrshd 1.3.6.1.4.1.8886.1.1.3.2.5
The threshold of memory monitor.
Status: current Access: read-write
OBJECT-TYPE    
  INTEGER  

raisecomMemoryThrshdRecover 1.3.6.1.4.1.8886.1.1.3.2.6
The recover threshold of memory monitor.
Status: current Access: read-write
OBJECT-TYPE    
  INTEGER  

raisecomMemoryMonInterval 1.3.6.1.4.1.8886.1.1.3.2.7
The timer interval of memory monitor.
Status: current Access: read-write
OBJECT-TYPE    
  INTEGER  

raisecomDeviceType 1.3.6.1.4.1.8886.1.1.4.1
Device type.
Status: current Access: read-only
OBJECT-TYPE    
  OCTET STRING  

raisecomInformation 1.3.6.1.4.1.8886.1.1.4
raisecom System objects: objects common to all platforms.
MODULE-IDENTITY    

raisecomDeviceType 1.3.6.1.4.1.8886.1.1.4.1
Device type.
Status: current Access: read-only
OBJECT-TYPE    
  OCTET STRING  

raisecomTemperature 1.3.6.1.4.1.8886.1.1.4.2
OBJECT IDENTIFIER    

raisecomTemperatureValue 1.3.6.1.4.1.8886.1.1.4.2.1
The current temperature of the device.
Status: current Access: read-only
OBJECT-TYPE    
  INTEGER  

raisecomTemperatureMin 1.3.6.1.4.1.8886.1.1.4.2.2
The minimum temperature that has occured.
Status: current Access: read-only
OBJECT-TYPE    
  INTEGER  

raisecomTemperatureMax 1.3.6.1.4.1.8886.1.1.4.2.3
The maximum temperature that has occured.
Status: current Access: read-only
OBJECT-TYPE    
  INTEGER  

raisecomTemperatureTrapEnable 1.3.6.1.4.1.8886.1.1.4.2.4
Indicates whether the temperature trap is enabled.
Status: deprecated Access: read-write
OBJECT-TYPE    
  EnableVar  

raisecomTemperatureThresholdLow 1.3.6.1.4.1.8886.1.1.4.2.5
Low threshold of the temperature alarm.
Status: current Access: read-write
OBJECT-TYPE    
  Integer32  

raisecomTemperatureThresholdHigh 1.3.6.1.4.1.8886.1.1.4.2.6
High threshold of the temperature alarm.
Status: current Access: read-write
OBJECT-TYPE    
  Integer32  

raisecomTemperatureTrapTimes 1.3.6.1.4.1.8886.1.1.4.2.7
How many times abnormal temperature has occured.
Status: current Access: read-only
OBJECT-TYPE    
  INTEGER  

raisecomTemperatureHighTimes 1.3.6.1.4.1.8886.1.1.4.2.8
How many times high temperature has occured.
Status: current Access: read-only
OBJECT-TYPE    
  INTEGER  

raisecomTemperatureLowTimes 1.3.6.1.4.1.8886.1.1.4.2.9
How many times low temperature has occured.
Status: current Access: read-only
OBJECT-TYPE    
  INTEGER  

raisecomVolt 1.3.6.1.4.1.8886.1.1.4.3
OBJECT IDENTIFIER    

raisecomVoltTable 1.3.6.1.4.1.8886.1.1.4.3.1
A table of device vlot and associated properties..
Status: current Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    RaisecomVoltEntry

raisecomVoltEntry 1.3.6.1.4.1.8886.1.1.4.3.1.1
Table entry for device vlot.
Status: current Access: not-accessible
OBJECT-TYPE    
  RaisecomVoltEntry  

raisecomVoltIndex 1.3.6.1.4.1.8886.1.1.4.3.1.1.1
An index based 1 that uniquely identifies a volt entry.
Status: current Access: read-only
OBJECT-TYPE    
  INTEGER  

raisecomVoltReference 1.3.6.1.4.1.8886.1.1.4.3.1.1.2
The reference volt.
Status: current Access: read-only
OBJECT-TYPE    
  INTEGER  

raisecomVoltValue 1.3.6.1.4.1.8886.1.1.4.3.1.1.3
The current value.
Status: current Access: read-only
OBJECT-TYPE    
  INTEGER  

raisecomVoltMin 1.3.6.1.4.1.8886.1.1.4.3.1.1.4
The minimum value that has occured.
Status: current Access: read-only
OBJECT-TYPE    
  INTEGER  

raisecomVoltMax 1.3.6.1.4.1.8886.1.1.4.3.1.1.5
The maximum value that has occured.
Status: current Access: read-only
OBJECT-TYPE    
  INTEGER  

raisecomVoltTrapEnable 1.3.6.1.4.1.8886.1.1.4.3.1.1.6
Indicates whether the volt trap is enabled.
Status: deprecated Access: read-write
OBJECT-TYPE    
  EnableVar  

raisecomVoltThresholdLow 1.3.6.1.4.1.8886.1.1.4.3.1.1.7
The low threshold of the volt alarm.
Status: current Access: read-write
OBJECT-TYPE    
  Integer32  

raisecomVoltThresholdHigh 1.3.6.1.4.1.8886.1.1.4.3.1.1.8
The high threshold of the volt alarm.
Status: current Access: read-write
OBJECT-TYPE    
  Integer32  

raisecomVoltTrapTimes 1.3.6.1.4.1.8886.1.1.4.3.1.1.9
How many times abnormal volt has occured.
Status: current Access: read-only
OBJECT-TYPE    
  INTEGER  

raisecomVoltHighTimes 1.3.6.1.4.1.8886.1.1.4.3.1.1.10
How many times high volt has occured.
Status: current Access: read-only
OBJECT-TYPE    
  INTEGER  

raisecomVoltLowTimes 1.3.6.1.4.1.8886.1.1.4.3.1.1.11
How many times low volt has occured.
Status: current Access: read-only
OBJECT-TYPE    
  INTEGER  

raisecomInformationTrap 1.3.6.1.4.1.8886.1.1.4.4
OBJECT IDENTIFIER    

temperatureAbnormalTrap 1.3.6.1.4.1.8886.1.1.4.4.1
Current temperature of the device is abnormal.
Status: deprecated Access: read-only
NOTIFICATION-TYPE    

temperatureNormalTrap 1.3.6.1.4.1.8886.1.1.4.4.2
Current temperature of the device return to normal.
Status: deprecated Access: read-only
NOTIFICATION-TYPE    

raisecomVoltAbnormalTrap 1.3.6.1.4.1.8886.1.1.4.4.3
Current volt of the device is abnormal.
Status: deprecated Access: read-only
NOTIFICATION-TYPE    

raisecomVoltNormalTrap 1.3.6.1.4.1.8886.1.1.4.4.4
Current volt of the device return to normal.
Status: deprecated Access: read-only
NOTIFICATION-TYPE    

raisecomAlarm 1.3.6.1.4.1.8886.1.1.4.7
OBJECT IDENTIFIER    

raisecomAlarmTrap 1.3.6.1.4.1.8886.1.1.4.7.1
OBJECT IDENTIFIER    

raisecomAlarmInformationTrap 1.3.6.1.4.1.8886.1.1.4.7.1.1
Trap transfer alarm information in the alarm history table.
Status: current Access: read-only
NOTIFICATION-TYPE    

raisecomAlarmGlobal 1.3.6.1.4.1.8886.1.1.4.7.2
OBJECT IDENTIFIER    

raisecomAlarmTrapEnable 1.3.6.1.4.1.8886.1.1.4.7.2.1
Indicates whether the global alarm trap is enabled.
Status: current Access: read-write
OBJECT-TYPE    
  EnableVar  

raisecomAlarmSyslogEnable 1.3.6.1.4.1.8886.1.1.4.7.2.2
Indicates whether the global alarm syslog is enabled.
Status: current Access: read-write
OBJECT-TYPE    
  EnableVar  

raisecomAlarmClear 1.3.6.1.4.1.8886.1.1.4.7.2.3
This object instructs the management entity to clear the whole current alarm information.
Status: current Access: read-write
OBJECT-TYPE    
  TruthValue  

raisecomAlarmPower 1.3.6.1.4.1.8886.1.1.4.7.3
OBJECT IDENTIFIER    

raisecomAlarmPowerTrapEnable 1.3.6.1.4.1.8886.1.1.4.7.3.1
Indicates whether the power alarm trap is enabled.
Status: current Access: read-write
OBJECT-TYPE    
  EnableVar  

raisecomAlarmPowerRelayEnable 1.3.6.1.4.1.8886.1.1.4.7.3.2
Indicates whether the power alarm relay is enabled.
Status: current Access: read-write
OBJECT-TYPE    
  EnableVar  

raisecomAlarmPowerSyslogEnable 1.3.6.1.4.1.8886.1.1.4.7.3.3
Indicates whether the power alarm syslog is enabled.
Status: current Access: read-write
OBJECT-TYPE    
  EnableVar  

raisecomAlarmPowerOneTimes 1.3.6.1.4.1.8886.1.1.4.7.3.4
How many times power one alarm has occured.
Status: current Access: read-only
OBJECT-TYPE    
  INTEGER  

raisecomAlarmPowerTwoTimes 1.3.6.1.4.1.8886.1.1.4.7.3.5
How many times power two alarm has occured.
Status: current Access: read-only
OBJECT-TYPE    
  INTEGER  

raisecomAlarmPowerStatus 1.3.6.1.4.1.8886.1.1.4.7.3.6
The status of power alarm.
Status: current Access: read-only
OBJECT-TYPE    
  INTEGER dual-power-on(1), dual-power-off(2), power1-off(3), power2-off(4)  

raisecomAlarmTemperature 1.3.6.1.4.1.8886.1.1.4.7.4
OBJECT IDENTIFIER    

raisecomAlarmTemperatureTrapEnable 1.3.6.1.4.1.8886.1.1.4.7.4.1
Indicates whether the temperature alarm trap is enabled.
Status: current Access: read-write
OBJECT-TYPE    
  EnableVar  

raisecomAlarmTemperatureRelayEnable 1.3.6.1.4.1.8886.1.1.4.7.4.2
Indicates whether the temperature alarm relay is enabled.
Status: current Access: read-write
OBJECT-TYPE    
  EnableVar  

raisecomAlarmTemperatureSyslogEnable 1.3.6.1.4.1.8886.1.1.4.7.4.3
Indicates whether the temperature alarm syslog is enabled.
Status: current Access: read-write
OBJECT-TYPE    
  EnableVar  

raisecomAlarmVoltage 1.3.6.1.4.1.8886.1.1.4.7.5
OBJECT IDENTIFIER    

raisecomAlarmVoltTrapEnable 1.3.6.1.4.1.8886.1.1.4.7.5.1
Indicates whether the volt alarm trap is enabled.
Status: current Access: read-write
OBJECT-TYPE    
  EnableVar  

raisecomAlarmVoltRelayEnable 1.3.6.1.4.1.8886.1.1.4.7.5.2
Indicates whether the volt alarm relay is enabled.
Status: current Access: read-write
OBJECT-TYPE    
  EnableVar  

raisecomAlarmVoltSyslogEnable 1.3.6.1.4.1.8886.1.1.4.7.5.3
Indicates whether the volt alarm syslog is enabled.
Status: current Access: read-write
OBJECT-TYPE    
  EnableVar  

raisecomAlarmPort 1.3.6.1.4.1.8886.1.1.4.7.6
OBJECT IDENTIFIER    

raisecomAlarmPortTable 1.3.6.1.4.1.8886.1.1.4.7.6.1
A table of port alarm information..
Status: current Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    RaisecomAlarmPortEntry

raisecomAlarmPortEntry 1.3.6.1.4.1.8886.1.1.4.7.6.1.1
Table entry for port alarm information.
Status: current Access: not-accessible
OBJECT-TYPE    
  RaisecomAlarmPortEntry  

raisecomAlarmPortIndex 1.3.6.1.4.1.8886.1.1.4.7.6.1.1.1
This object index of alarm port entry.
Status: current Access: not-accessible
OBJECT-TYPE    
  INTEGER  

raisecomAlarmPortSyslogEvList 1.3.6.1.4.1.8886.1.1.4.7.6.1.1.2
The port alarm event list of syslog enable status.
Status: current Access: read-write
OBJECT-TYPE    
  PortAlarmEventList  

raisecomAlarmPortNotifiesEvList 1.3.6.1.4.1.8886.1.1.4.7.6.1.1.3
The port alarm event list of notifies enable status.
Status: current Access: read-write
OBJECT-TYPE    
  PortAlarmEventList  

raisecomAlarmPortRelayEvList 1.3.6.1.4.1.8886.1.1.4.7.6.1.1.4
The port alarm event list of relay enable status.
Status: current Access: read-write
OBJECT-TYPE    
  PortAlarmEventList  

raisecomAlarmPortEvList 1.3.6.1.4.1.8886.1.1.4.7.6.1.1.5
The current alarm information on port.
Status: current Access: read-only
OBJECT-TYPE    
  PortAlarmEventList  

raisecomAlarmHistory 1.3.6.1.4.1.8886.1.1.4.7.7
OBJECT IDENTIFIER    

raisecomAlarmHistTable 1.3.6.1.4.1.8886.1.1.4.7.7.1
A table of history alarm information..
Status: current Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    RaisecomAlarmHistEntry

raisecomAlarmHistEntry 1.3.6.1.4.1.8886.1.1.4.7.7.1.1
Table entry for history alarm information.
Status: current Access: not-accessible
OBJECT-TYPE    
  RaisecomAlarmHistEntry  

raisecomAlarmHistIndex 1.3.6.1.4.1.8886.1.1.4.7.7.1.1.1
This object index of alarm history entry.
Status: current Access: not-accessible
OBJECT-TYPE    
  INTEGER  

raisecomAlarmHistStatus 1.3.6.1.4.1.8886.1.1.4.7.7.1.1.2
The status of alarm information asserted:alarm has generated, cleared:alarm is cleared, clearall:all of alarm is cleared.
Status: current Access: read-only
OBJECT-TYPE    
  INTEGER high-volt-cleared(1), low-volt-cleared(2), high-temperature-cleared(3), low-temperature-cleared(4)  

raisecomAlarmHistSource 1.3.6.1.4.1.8886.1.1.4.7.7.1.1.3
The source of alarm information switch or port.
Status: current Access: read-only
OBJECT-TYPE    
  INTEGER  

raisecomAlarmHistDescr 1.3.6.1.4.1.8886.1.1.4.7.7.1.1.4
The description of alarm information.
Status: current Access: read-only
OBJECT-TYPE    
  OCTET STRING Size(0..64)  

raisecomAlarmHistTimestamp 1.3.6.1.4.1.8886.1.1.4.7.7.1.1.5
The timestamp of alarm information.
Status: current Access: read-only
OBJECT-TYPE    
  INTEGER  

raisecomAlarmHistType 1.3.6.1.4.1.8886.1.1.4.7.7.1.1.6
The type of alarm information.
Status: current Access: read-only
OBJECT-TYPE    
  INTEGER dev-power-down(0), power-abnormal(1), high-temperature(2), low-temperature(3), high-volt(4), low-volt(5), link-down(6), link-falut(7), not-forward(8), power-normal(9), normal-high-temperature(10), normal-high-volt(11), link-up(12), link-ok(13), forward(14), all-alarm(15), offline(16), online(17), power-on(18), normal-low-temperature(19), normal-low-volt(20)  

raisecomAlarmCurrent 1.3.6.1.4.1.8886.1.1.4.7.8
OBJECT IDENTIFIER    

raisecomAlarmCurtTable 1.3.6.1.4.1.8886.1.1.4.7.8.1
A table of current alarm information..
Status: current Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    RaisecomAlarmCurtEntry

raisecomAlarmCurtEntry 1.3.6.1.4.1.8886.1.1.4.7.8.1.1
Table entry for current alarm information.
Status: current Access: not-accessible
OBJECT-TYPE    
  RaisecomAlarmCurtEntry  

raisecomAlarmCurtIndex 1.3.6.1.4.1.8886.1.1.4.7.8.1.1.1
This object index of alarm current entry.
Status: current Access: not-accessible
OBJECT-TYPE    
  INTEGER  

raisecomAlarmCurtSource 1.3.6.1.4.1.8886.1.1.4.7.8.1.1.2
The source of alarm information switch or port.
Status: current Access: read-only
OBJECT-TYPE    
  INTEGER  

raisecomAlarmCurtDescr 1.3.6.1.4.1.8886.1.1.4.7.8.1.1.3
The description of alarm information.
Status: current Access: read-only
OBJECT-TYPE    
  OCTET STRING Size(0..64)  

raisecomAlarmCurtTimestamp 1.3.6.1.4.1.8886.1.1.4.7.8.1.1.4
The timestamp of alarm information.
Status: current Access: read-only
OBJECT-TYPE    
  INTEGER  

raisecomAlarmCurtType 1.3.6.1.4.1.8886.1.1.4.7.8.1.1.5
The type of alarm information.
Status: current Access: read-only
OBJECT-TYPE    
  INTEGER dev-power-down(0), power-abnormal(1), high-temperature(2), low-temperature(3), high-volt(4), low-volt(5), link-down(6), link-falut(7), not-forward(8)  

Generation date: July 28, 2023, 16:18:13, Copyright © 2007 - 2022 - Circitor