QB-VT15-MIB

File: QB-VT15-MIB.mib (27488 bytes)

Imported modules

SNMPv2-SMI SNMPv2-TC SNMPv2-CONF
IF-MIB QUANTUMBRIDGE-REG ATM-TC-MIB
QB-DWS-MIB

Imported symbols

NOTIFICATION-TYPE MODULE-IDENTITY OBJECT-TYPE
Gauge32 Counter32 Unsigned32
Integer32 TimeTicks TEXTUAL-CONVENTION
TruthValue TimeStamp RowStatus
DisplayString MODULE-COMPLIANCE OBJECT-GROUP
InterfaceIndex InterfaceIndexOrZero ifIndex
qbMibs AtmAddr AtmConnKind
AtmConnCastType AtmServiceCategory AtmTrafficDescrParamIndex
AtmVpIdentifier AtmVcIdentifier AtmVorXAdminStatus
AtmVorXLastChange AtmVorXOperStatus atmNoClpNoScr
QbEnableStatus QbPvcConnKind

Defined Types

QbVT15Sts1  
The STS-1 number.
TEXTUAL-CONVENTION    
  Unsigned32 1..3  

QbVT15VTGroup  
The VT1.5 group number.
TEXTUAL-CONVENTION    
  Unsigned32 1..7  

QbVT15VTGroupId  
The VT1.5 group number.
TEXTUAL-CONVENTION    
  Unsigned32 1..4  

QbVT15VTId  
The VT Identifier number. The qbVT15VTId is determined by using the following formula: (sts-1) * 28 + (vtgrp-1) * 4 + vtnum. sts-sonet path, vtgrp - sonet path group, vt - VT number.
TEXTUAL-CONVENTION    
  Unsigned32 1..84  

QbVC12Id  
The VC Identifier number.
TEXTUAL-CONVENTION    
  Unsigned32 1..63  

QbVTVCConnEntry  
SEQUENCE    
  qbVTVCIfIndex InterfaceIndex
  qbVTVCConnId INTEGER
  qbVTVCConnIotAtmIfIndex InterfaceIndexOrZero
  qbVTVCConnName DisplayString
  qbVTVCConnAdminStatus AtmVorXAdminStatus
  qbVTVCConnOperStatus AtmVorXOperStatus
  qbVTVCConnLastChange AtmVorXLastChange
  qbVTVCConnAtmVpi AtmVpIdentifier
  qbVTVCConnAtmVci AtmVcIdentifier
  qbVTVCConnKind QbPvcConnKind
  qbVTVCCrossConnId INTEGER
  qbVTVCConnRowStatus RowStatus
  qbVTVCConnLoopback QbEnableStatus
  qbVTVCConnLoopbackEndpt INTEGER

QbVTVCCrossConnEntry  
SEQUENCE    
  qbVTVCCrossConnIfIndexEndpt1 InterfaceIndex
  qbVTVCCrossConnVTIdEndpt1 INTEGER
  qbVTVCCrossConnIfIndexEndpt2 InterfaceIndex
  qbVTVCCrossConnVTIdEndpt2 INTEGER
  qbVTVCCrossConnIndex INTEGER
  qbVTVCCrossConnName DisplayString
  qbVTVCCrossConnAdminStatus AtmVorXAdminStatus
  qbVTVCCrossConnOperStatus AtmVorXOperStatus
  qbVTVCCrossConnKind QbPvcConnKind
  qbVTVCCrossConnRowStatus RowStatus

QbVTConfEntry  
SEQUENCE    
  qbVTConfIfIndex InterfaceIndex
  qbVTConfVTId QbVT15VTId
  qbVTConfClockMode INTEGER
  qbVTConfAction INTEGER

QbVtVcStatsEntry  
SEQUENCE    
  qbVtVcStatsIfIndex InterfaceIndex
  qbVtVcStatsConnId INTEGER
  qbVtVcStatsRxCells Counter32
  qbVtVcStatsTxCells Counter32
  qbVtVcStatsRxDroppedCells Counter32
  qbVtVcStatsTxConditionalCells Counter32
  qbVtVcStatsTxSuppressedCells Counter32

Defined Values

qbVTVCMIB 1.3.6.1.4.1.4323.2.9
This module defines additional objects for the provisioning of VT1.5/VC12 links in Quantum Bridge devices.
MODULE-IDENTITY    

qbVTVCTables 1.3.6.1.4.1.4323.2.9.1
OBJECT IDENTIFIER    

qbVTVCNotifications 1.3.6.1.4.1.4323.2.9.2
OBJECT IDENTIFIER    

qbVTVCConformance 1.3.6.1.4.1.4323.2.9.3
OBJECT IDENTIFIER    

qbVTVCConnTable 1.3.6.1.4.1.4323.2.9.1.1
The Quantum Bridge VT connection table contains a list of VT1.5 connections that are provisioned at OAS SONET(STS-3) and SDH(STM-1) interfaces between IOT(DS1/E1) ports and VTs/VCs, ATM PVCs and VTs/VCs, VTs/VCs and VTs/VCs ports. The STS-3 interfaces are listed in the sonetMediumTable(RFC2558) as interfaces with the 'sonetMediumType' object set to sonet(1) value. The STM-1 interfaces are listed in the sonetMediumTable(RFC2558) as interfaces with the 'sonetMediumType' object set to sdh(1). The table has 2 indexes of the first end-point: Sonet interface index, vt/vc identifier. Note: All connections between ATM ports and VTs/VCs are listed in the atmVclTable.
Status: current Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    QbVTVCConnEntry

qbVTVCConnEntry 1.3.6.1.4.1.4323.2.9.1.1.1
An entry in the Quantum Bridge qbVTVCConnTable table.
Status: current Access: not-accessible
OBJECT-TYPE    
  QbVTVCConnEntry  

qbVTVCIfIndex 1.3.6.1.4.1.4323.2.9.1.1.1.1
The STS-3/SDH-1 signal interface.
Status: current Access: not-accessible
OBJECT-TYPE    
  InterfaceIndex  

qbVTVCConnId 1.3.6.1.4.1.4323.2.9.1.1.1.2
The identifier of the specified VT (virtual tributary) or VC signal. The VT identifier is determined by using the following formula: (sts-1) * 28 + (vtgrp-1) * 4 + vtnum. sts-sonet path, vtgrp - sonet path group, vt - VT number.The VC identifier has ranges from 1 to 63.
Status: current Access: not-accessible
OBJECT-TYPE    
  INTEGER 1..84  

qbVTVCConnIotAtmIfIndex 1.3.6.1.4.1.4323.2.9.1.1.1.3
An IOT interface index of the atm layer interface or DS1/E1 interface of the connection between an ATM/IOT and a VT1.5/VC12 or VT1.5/VC12 and VT1.5/VC12. The connection type is indicated by the qbVTVCConnKind object. If this object is set to vt15ToAtm or vt15ToAtm the ATM layer interface is specified. When the iotE1ToVt15, iotDs1ToVt15,iotE1ToVc12, iotDs1ToVc12 values are set the IOT DS1/E1 interface is specified. For a VT to VT connection this object isn't needed.
Status: current Access: read-create
OBJECT-TYPE    
  InterfaceIndexOrZero  

qbVTVCConnName 1.3.6.1.4.1.4323.2.9.1.1.1.4
The textual name of the VT1.5/VC12 connection as specified by a user. It provides a non-volatile handle for this PVC.The supplied name in the qbVTVCConnName is associated with the same connection for as long as that connection remains.
Status: current Access: read-create
OBJECT-TYPE    
  DisplayString Size(1..20)  

qbVTVCConnAdminStatus 1.3.6.1.4.1.4323.2.9.1.1.1.5
The desired administrative status of the connection The up and down states indicate that the traffic flow is enabled or disabled respectively across the specified connection.
Status: current Access: read-create
OBJECT-TYPE    
  AtmVorXAdminStatus  

qbVTVCConnOperStatus 1.3.6.1.4.1.4323.2.9.1.1.1.6
The current operational status of the connection.
Status: current Access: read-only
OBJECT-TYPE    
  AtmVorXOperStatus  

qbVTVCConnLastChange 1.3.6.1.4.1.4323.2.9.1.1.1.7
The value of sysUpTime at the time this connection entered its current operational state.
Status: current Access: read-only
OBJECT-TYPE    
  AtmVorXLastChange  

qbVTVCConnAtmVpi 1.3.6.1.4.1.4323.2.9.1.1.1.8
The value of this object is equal to the VPI used by the ATM VCL mapped through this connection to a VT. The value is irrelevant for a non-ATM connection. (i.e., qbVTVCConnKind isn't set vt15ToAtm or vc12ToAtm value).
Status: current Access: read-create
OBJECT-TYPE    
  AtmVpIdentifier  

qbVTVCConnAtmVci 1.3.6.1.4.1.4323.2.9.1.1.1.9
The value of this object is equal to the VCI used by the ATM VCL mapped through this connection to a VT. The value is irrelevant if a non-ATM connection. (i.e., qbVTVCConnKind isn't set to vt15ToAtm or vc12ToAtm value).
Status: current Access: read-create
OBJECT-TYPE    
  AtmVcIdentifier  

qbVTVCConnKind 1.3.6.1.4.1.4323.2.9.1.1.1.10
The VT connection type. Two types of connection can be provisioned on the VT/sonet port (IOT-VT and VT-ATM)
Status: current Access: read-create
OBJECT-TYPE    
  QbPvcConnKind  

qbVTVCCrossConnId 1.3.6.1.4.1.4323.2.9.1.1.1.11
This object is instantiated only for a VT/VC which is cross-connected to another VT/VC. Two entries that have the same value belong to a single entry of qbVTVCCrossConnTable. The corresponding entry in qbVTVCCrossConnTable can be found by sending getnext with qbVTVCIfIndex qbVTVCConnId instances. The value is irrelevant for a non-VTtpVT connection (i.e., qbVTVCConnKind isn't set to vt15Vt15 or vt12Vt12 value).
Status: current Access: read-only
OBJECT-TYPE    
  INTEGER 0..2147483647  

qbVTVCConnRowStatus 1.3.6.1.4.1.4323.2.9.1.1.1.12
The status column for this IOT ENET interface. This OBJECT can be set to: createAndGo(4) destroy(6) The following values may be read: active(1) This object may only be set to createAndGo(4). Setting this object to active(1) when its value is already active(1) is a no-op. Setting this object to createAndGo(4) causes the agent to attempt to create and commit a row based on the contents of the objects in the row. If all necessary information is present in the row and the values are acceptable to the agent, the agent will change the status to active(1). If any of the necessary objects are not available, the agent will reject the creation request.
Status: current Access: read-create
OBJECT-TYPE    
  RowStatus  

qbVTVCConnLoopback 1.3.6.1.4.1.4323.2.9.1.1.1.13
Activate a connection loopback for a PVC that has an endpoint on this VT. This object, when read, returns one of the following results: enable(1): Loopback is enabled on this VT disable(2): Loopback is disbaled on this VT Setting this object to one of the acceptable values causes the following results depending on the qbVTVCConnLoopbackEndpt value: enable(1): Enable loopback on this VT trib when qbVTVCConnLoopbackEndpt is set to 'vtLoopback'. Enable loopback on IOT or ATM port when qbVTVCConnLoopbackEndpt is set to nonVtloopback'. For VT to VT connection this object activates loopback on this VT. disable(2): Disbale activated loopback. The disabled endpoint is selected depending of the qbVTVCConnLoopbackEndpt
Status: current Access: read-create
OBJECT-TYPE    
  QbEnableStatus  

qbVTVCConnLoopbackEndpt 1.3.6.1.4.1.4323.2.9.1.1.1.14
Define an endpoint on which loopback is activated or disabled. The object works in conjunction with the qbVTVCConnLoopback.
Status: current Access: read-create
OBJECT-TYPE    
  INTEGER vtLoopback(1), nonVtLoopback(2)  

qbVTVCCrossConnTable 1.3.6.1.4.1.4323.2.9.1.2
The Quantum Bridge VT cross-connection (VT to VT) table contains all point-to-point cross-connections between various VTs that are provisoned at OAS STS-3 Sonet interfaces. The STS-3 interfaces are listed in the sonetMediumTable(RFC2558) as interfaces with the 'sonetMediumType' object set to sonet(1). The table is indexed by four indexes: low interface interface index,low vt identifiers, high interface index, and high vt identifier. The terms low and high are chosen to represent numerical ordering of two interfaces/vt within VT cross-connect.
Status: current Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    QbVTVCCrossConnEntry

qbVTVCCrossConnEntry 1.3.6.1.4.1.4323.2.9.1.2.1
An entry in the Quantum Bridge QbVTVCCrossConnTable.
Status: current Access: not-accessible
OBJECT-TYPE    
  QbVTVCCrossConnEntry  

qbVTVCCrossConnIfIndexEndpt1 1.3.6.1.4.1.4323.2.9.1.2.1.1
The STS-3/SDH-1 Sonet low interface index of the specified cross-connection.
Status: current Access: not-accessible
OBJECT-TYPE    
  InterfaceIndex  

qbVTVCCrossConnVTIdEndpt1 1.3.6.1.4.1.4323.2.9.1.2.1.2
The low VT/VC identifier of the specified VT/VC group of the first cross-connect endpoint.
Status: current Access: not-accessible
OBJECT-TYPE    
  INTEGER 1..84  

qbVTVCCrossConnIfIndexEndpt2 1.3.6.1.4.1.4323.2.9.1.2.1.3
The high STS-3 Sonet interface of the specified cross-connection of the second cross-connect endpoint.
Status: current Access: not-accessible
OBJECT-TYPE    
  InterfaceIndex  

qbVTVCCrossConnVTIdEndpt2 1.3.6.1.4.1.4323.2.9.1.2.1.4
The high VT/VC identifier of the specified VT group of the second cross-connect endpoint.
Status: current Access: not-accessible
OBJECT-TYPE    
  INTEGER 1..84  

qbVTVCCrossConnIndex 1.3.6.1.4.1.4323.2.9.1.2.1.5
A unique value to identify this VT to VT cross-connect. For each qbVTVCConnEntry associated with this cross-connect, the agent reports this cross-connect index value in the qbVTVCCrossConnId attribute of the corresponding qbVTVCConnTable entries.
Status: current Access: read-create
OBJECT-TYPE    
  INTEGER 1..2147483647  

qbVTVCCrossConnName 1.3.6.1.4.1.4323.2.9.1.2.1.6
The textual name of the VT1.5 cross-connection as specified by a user. It provides a non-volatile handle for this cross-connection. The supplied name in the qbVTVCCrossName is associated with the same cross-connection for as long as that cross-conection remains.
Status: current Access: read-create
OBJECT-TYPE    
  DisplayString Size(1..20)  

qbVTVCCrossConnAdminStatus 1.3.6.1.4.1.4323.2.9.1.2.1.7
The desired administrative status of the specified cross-connection. The up and down states indicate that the traffic flow is enabled or disabled across this cross-connection.
Status: current Access: read-create
OBJECT-TYPE    
  AtmVorXAdminStatus  

qbVTVCCrossConnOperStatus 1.3.6.1.4.1.4323.2.9.1.2.1.8
The current operational status of the connection.
Status: current Access: read-only
OBJECT-TYPE    
  AtmVorXOperStatus  

qbVTVCCrossConnKind 1.3.6.1.4.1.4323.2.9.1.2.1.9
The VT connection type. Two types of connection can be provisioned on the VT-VT and VC-VC.
Status: current Access: read-create
OBJECT-TYPE    
  QbPvcConnKind  

qbVTVCCrossConnRowStatus 1.3.6.1.4.1.4323.2.9.1.2.1.10
The status column for this IOT ENET interface. This OBJECT can be set to: createAndGo(4) destroy(6) The following values may be read: active(1) This object may only be set to createAndGo(4). Setting this object to active(1) when its value is already active(1) is a no-op. Setting this object to createAndGo(4) causes the agent to attempt to create and commit a row based on the contents of the objects in the row. If all necessary information is present in the row and the values are acceptable to the agent, the agent will change the status to active(1). If any of the necessary objects are not available, the agent will reject the creation request. Setting this object to destroy(6) will remove the corresponding entry in this table, and disable data traffic.
Status: current Access: read-create
OBJECT-TYPE    
  RowStatus  

qbVTConfTable 1.3.6.1.4.1.4323.2.9.1.3
The Quantum Bridge VT configuration table contains configuration parameters of tributaries at OAS VT155 interfaces. The STS-3 interfaces of D155VT cards that are listed in the sonetMediumTable(RFC2558) as interfaces with the 'sonetMediumType' object set to sonet(1). The table has two indexes: Sonet interface index, and tributary identifier.
Status: current Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    QbVTConfEntry

qbVTConfEntry 1.3.6.1.4.1.4323.2.9.1.3.1
An entry in the Quantum Bridge qbVTConfEntry. Every entry containes settings of the tributary
Status: current Access: not-accessible
OBJECT-TYPE    
  QbVTConfEntry  

qbVTConfIfIndex 1.3.6.1.4.1.4323.2.9.1.3.1.1
The STS-3/SDH-1 Sonet interface of the specified tributary.
Status: current Access: not-accessible
OBJECT-TYPE    
  InterfaceIndex  

qbVTConfVTId 1.3.6.1.4.1.4323.2.9.1.3.1.2
The identifier of the specified tributary.
Status: current Access: not-accessible
OBJECT-TYPE    
  QbVT15VTId  

qbVTConfClockMode 1.3.6.1.4.1.4323.2.9.1.3.1.3
The object defines whether VT155 service clocking mode used for AAL1 recovery. Applies only to D155VT interfaces that are configured for SONET format.
Status: current Access: read-write
OBJECT-TYPE    
  INTEGER srts(1), adaptive(2)  

qbVTConfAction 1.3.6.1.4.1.4323.2.9.1.3.1.4
Indicates whether the clock mode is set for a single tributary or group of tributaries. When set to 'singleVTAction(1)' a single selected tributary is set to a desired clock mode. When set to 'stsVTAction(2)' all tributaries that belongs to qbVTConfVTId's STS are set to a desired clock mode. When set to 'ifVTAction(3)' all qbVTConfIfIndex tributaries are set to a desired clock mode. For this mode the value of qbVTConfVTId is irrelevant. Thus any valid QbVT15VTId value can be used. When the value is set to 'noop', no operation is performed. When read, this object always returns the value noop(4).
Status: current Access: read-write
OBJECT-TYPE    
  INTEGER singleVTAction(1), stsVTAction(2), ifVTAction(3), noop(4)  

qbVtVcStatsTable 1.3.6.1.4.1.4323.2.9.1.4
This table contains the stats for each VT/VC with a connection established. One row in this table should exist for each VT/VC connection.
Status: current Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    QbVtVcStatsEntry

qbVtVcStatsEntry 1.3.6.1.4.1.4323.2.9.1.4.1
An entry in the Quantum Bridge qbVtVcStatsTable table.
Status: current Access: not-accessible
OBJECT-TYPE    
  QbVtVcStatsEntry  

qbVtVcStatsIfIndex 1.3.6.1.4.1.4323.2.9.1.4.1.1
The STS-3/SDH-1 signal interface.
Status: current Access: not-accessible
OBJECT-TYPE    
  InterfaceIndex  

qbVtVcStatsConnId 1.3.6.1.4.1.4323.2.9.1.4.1.2
The identifier of the specified VT (virtual tributary) or VC signal. The VT identifier is determined by using the following formula: (sts-1) * 28 + (vtgrp-1) * 4 + vtnum. sts-sonet path, vtgrp - sonet path group, vt - VT number.The VC identifier has ranges from 1 to 63.
Status: current Access: not-accessible
OBJECT-TYPE    
  INTEGER 1..84  

qbVtVcStatsRxCells 1.3.6.1.4.1.4323.2.9.1.4.1.3
The number of received cells.
Status: current Access: read-only
OBJECT-TYPE    
  Counter32  

qbVtVcStatsTxCells 1.3.6.1.4.1.4323.2.9.1.4.1.4
The number of transmitted cells.
Status: current Access: read-only
OBJECT-TYPE    
  Counter32  

qbVtVcStatsRxDroppedCells 1.3.6.1.4.1.4323.2.9.1.4.1.5
The number of received cells that were dropped.
Status: current Access: read-only
OBJECT-TYPE    
  Counter32  

qbVtVcStatsTxConditionalCells 1.3.6.1.4.1.4323.2.9.1.4.1.6
The number of transmitted conditional cells.
Status: current Access: read-only
OBJECT-TYPE    
  Counter32  

qbVtVcStatsTxSuppressedCells 1.3.6.1.4.1.4323.2.9.1.4.1.7
The number of transmitted supressed cells.
Status: current Access: read-only
OBJECT-TYPE    
  Counter32  

qbVTVCNotificationPrefix 1.3.6.1.4.1.4323.2.9.2.0
OBJECT IDENTIFIER    

qbVTVCConnOperStatusChange 1.3.6.1.4.1.4323.2.9.2.0.1
A notification indicates that a VT15 connection has chaged the operations status. The notification is originated for every connection which is listed in the qbVTVCConnTable when its the qbVTVCConnOperStatus object changed state.
Status: current Access: read-only
NOTIFICATION-TYPE    

qbVTVCCrossConnOperStatusChange 1.3.6.1.4.1.4323.2.9.2.0.2
A notification indicates that a VT15 cross-connection has chaged the operations status. The notification is originated for every connection which is listed in the qbVT15CrossConnTable when its the qbVTVCCrossConnOperStatus object changed state.
Status: current Access: read-only
NOTIFICATION-TYPE    

qbVTVCCompliances 1.3.6.1.4.1.4323.2.9.3.1
OBJECT IDENTIFIER    

qbVTVCGroups 1.3.6.1.4.1.4323.2.9.3.2
OBJECT IDENTIFIER    

qbVTVCCompliance 1.3.6.1.4.1.4323.2.9.3.1.1
The compliance statement for all agents that support this MIB. A compliant agent implements all objects defined in this MIB.
Status: current Access: read-only
MODULE-COMPLIANCE    

qbVTVCConnInfo 1.3.6.1.4.1.4323.2.9.3.2.1
The set of all accessible objects in this MIB.
Status: current Access: read-only
OBJECT-GROUP    

qbVTVCCrossConnInfo 1.3.6.1.4.1.4323.2.9.3.2.2
The set of all accessible objects in this MIB.
Status: current Access: read-only
OBJECT-GROUP