QB-ATM-MIB

File: QB-ATM-MIB.mib (92057 bytes)

Imported modules

SNMPv2-SMI ATM-MIB ATM-TC-MIB
SNMPv2-TC IF-MIB SNMPv2-CONF
QBSYS-SYSTEM-MIB QUANTUMBRIDGE-REG QB-DWS-MIB

Imported symbols

OBJECT-IDENTITY MODULE-IDENTITY OBJECT-TYPE
Counter32 IpAddress Integer32
atmTrafficDescrParamEntry atmVcCrossConnectEntry atmVpCrossConnectEntry
atmInterfaceConfEntry atmVclEntry atmVplEntry
AtmAddr AtmConnKind AtmConnCastType
AtmServiceCategory AtmTrafficDescrParamIndex AtmVpIdentifier
AtmVcIdentifier AtmVorXAdminStatus AtmVorXLastChange
AtmVorXOperStatus atmNoClpNoScr TEXTUAL-CONVENTION
DisplayString RowStatus TruthValue
InterfaceIndex InterfaceIndexOrZero ifIndex
MODULE-COMPLIANCE OBJECT-GROUP TimeStamp
qbMibs QbEnableStatus QbPvcConnKind

Defined Types

Boolean  
INTEGER true(1), false(2)    

QbAtmPnniWeight  
The ATM administrative weight of the ATM interface used by the PNNI Routing Control
TEXTUAL-CONVENTION    
  INTEGER 100..1000000  

QbAtmPnniNodeId  
Global PNNI Node Id used in the QB PNNI system.
TEXTUAL-CONVENTION    
  OCTET STRING Size(22)  

QbAtmSigSpec  
The ATM interface signalling spec.
TEXTUAL-CONVENTION    
  INTEGER other(1), uni30(2), uni31(3), uni40(4), pnni(5), iisp30(6), iisp31(7), aini(8)  

QbAtmPnniHelloState  
The state of an instance of the PNNI Hello State machine.
TEXTUAL-CONVENTION    
  INTEGER notApplicable(1), down(2), attempt(3), oneWayInside(4), twoWayInside(5), oneWayOutside(6), twoWayOutside(7), commonOutside(8)  

QbAtmPnniAtmAddr  
The ATM address used by the network entity. The address types are: no address (0 octets), and NSAP (20 octets).
TEXTUAL-CONVENTION    
  OCTET STRING Size(0|20)  

QbAtmPnniNodeIndex  
An index that identifies a logical PNNI entity within the managed system. The distinguished value zero indicates the null instance or no instance in the qbAtmPnniNodeCfgParentNodeIndex. In all other cases, the distinguished value zero indicates a logical entity within the switching system that manages routes only over non-PNNI interfaces. By default, only the node identified by node index one is created, and all PNNI interfaces are associated with that node.
TEXTUAL-CONVENTION    
  Integer32 0..65535  

QbAtmPnniPeerGroupId  
A PNNI peer group ID.
TEXTUAL-CONVENTION    
  OCTET STRING Size(14)  

QbF4F5LoopbackStatus  
in-progress(1) or success(2) or timeout(3).
TEXTUAL-CONVENTION    
  INTEGER in-progress(1), success(2), timeout(3)  

QbF4F5Status  
Definition of F4/F5 OperStatus
TEXTUAL-CONVENTION    
  BITS cc-seg(0), cc-ete(1), rdi-seg(2), rdi-ete(3), ais-seg(4), ais-ete(5), good(6), unavailable(7)  

QbAtmInterfaceConfEntry  
SEQUENCE    
  qbAtmInterfaceConfPolicingStatus INTEGER
  qbAtmInterfaceConfMaxPvcVci INTEGER
  qbAtmInterfaceConfMinPvcVci INTEGER
  qbAtmInterfaceConfMaxPvcVpi INTEGER
  qbAtmInterfaceConfMinPvcVpi INTEGER
  qbAtmInterfaceConfMaxPvpVpi INTEGER
  qbAtmInterfaceConfMinPvpVpi INTEGER

QbAtmTrafficDescrParamEntry  
SEQUENCE    
  qbAtmTrafficDescrParamName DisplayString
  qbAtmTrafficDescrParamDefault Boolean

QbAtmVclEntry  
SEQUENCE    
  qbAtmVclLoopback QbEnableStatus
  qbAtmVclF4F5LoopbackInsert OCTET STRING
  qbAtmVclF4F5LoopbackStatus QbF4F5LoopbackStatus
  qbAtmVclF4F5LoopbackTimestamp TimeStamp
  qbAtmVclMgmtIpAddr IpAddress
  qbAtmVclMgmtIpMask IpAddress
  qbAtmVclMgmtNeighborIP IpAddress
  qbAtmVclConnKind QbPvcConnKind
  qbAtmVclF4F5TxStatus QbF4F5Status
  qbAtmVclF4F5TxLastChange TimeStamp
  qbAtmVclF4F5RxStatus QbF4F5Status
  qbAtmVclF4F5RxLastChange TimeStamp

QbAtmVplEntry  
SEQUENCE    
  qbAtmVplLoopback QbEnableStatus
  qbAtmVplF4F5LoopbackInsert OCTET STRING
  qbAtmVplF4F5LoopbackStatus QbF4F5LoopbackStatus
  qbAtmVplF4F5LoopbackTimestamp TimeStamp
  qbAtmVplF4F5TxStatus QbF4F5Status
  qbAtmVplF4F5TxLastChange TimeStamp
  qbAtmVplF4F5RxStatus QbF4F5Status
  qbAtmVplF4F5RxLastChange TimeStamp

QbAtmVcCrossConnectEntry  
SEQUENCE    
  qbAtmVcCrossConnectName DisplayString
  qbAtmVcCrossConnectRxTrafficDescrIndex AtmTrafficDescrParamIndex
  qbAtmVcCrossConnectTxTrafficDescrIndex AtmTrafficDescrParamIndex

QbAtmVpCrossConnectEntry  
SEQUENCE    
  qbAtmVpCrossConnectName DisplayString
  qbAtmVpCrossConnectRxTrafficDescrIndex AtmTrafficDescrParamIndex
  qbAtmVpCrossConnectTxTrafficDescrIndex AtmTrafficDescrParamIndex

QbAtmPnniNodeEntry  
SEQUENCE    
  qbAtmPnniNodeIndex INTEGER
  qbAtmPnniNodeNetAddrPrefix OCTET STRING
  qbAtmPnniNodeEndSysId OCTET STRING
  qbAtmPnniNodeLevel INTEGER
  qbAtmPnniNodeRowStatus RowStatus
  qbAtmPnniNodeOperStatus INTEGER
  qbAtmPnniNodeAtmAddress QbAtmPnniAtmAddr
  qbAtmPnniNodePeerGroupId QbAtmPnniPeerGroupId

QbAtmPnniIfEntry  
SEQUENCE    
  qbAtmPnniIfNodeIndex INTEGER
  qbAtmPnniIfAdmWeightCbr QbAtmPnniWeight
  qbAtmPnniIfAdmWeightRtVbr QbAtmPnniWeight
  qbAtmPnniIfAdmWeightNrtVbr QbAtmPnniWeight
  qbAtmPnniIfAdmWeightAbr QbAtmPnniWeight
  qbAtmPnniIfAdmWeightUbr QbAtmPnniWeight
  qbAtmPnniIfRccServiceCategory AtmServiceCategory
  qbAtmPnniIfRccTrafficDescrIndex AtmTrafficDescrParamIndex
  qbAtmPnniIfPolicingStatus INTEGER

QbAtmPnniRouteAddrEntry  
SEQUENCE    
  qbAtmPnniRouteAddrAddress OCTET STRING
  qbAtmPnniRouteAddrIfIndex InterfaceIndex
  qbAtmPnniRouteAddrPrefixLength INTEGER
  qbAtmPnniRouteAddrRowStatus RowStatus
  qbAtmPnniRouteAddrProto INTEGER

QbAtmInterfaceConfSigEntry  
SEQUENCE    
  qbAtmInterfaceConfSigMode QbAtmSigSpec
  qbAtmInterfaceConfSigSide INTEGER
  qbAtmInterfaceConfSigParseMode INTEGER
  qbAtmInterfaceConfSigAdminStatus INTEGER
  qbAtmInterfaceConfSigSvcMinVci INTEGER
  qbAtmInterfaceConfSigSvcMaxVci INTEGER
  qbAtmInterfaceConfSigSvcMinVpi INTEGER
  qbAtmInterfaceConfSigSvcMaxVpi INTEGER
  qbAtmInterfaceConfSigSvpMinVpi INTEGER
  qbAtmInterfaceConfSigSvpMaxVpi INTEGER
  qbAtmInterfaceConfSigLastChange AtmVorXLastChange
  qbAtmInterfaceConfSigIlmiEnable Boolean

QbAtmPnniNbrPeerEntry  
SEQUENCE    
  qbAtmPnniPeerRemoteNodeId QbAtmPnniNodeId
  qbAtmPnniPeerState INTEGER
  qbAtmPnniPeerSvccRccIndex INTEGER
  qbAtmPnniPeerPortCount INTEGER
  qbAtmPnniPeerRcvDbSums Counter32
  qbAtmPnniPeerXmtDbSums Counter32
  qbAtmPnniPeerRcvPtsps Counter32
  qbAtmPnniPeerXmtPtsps Counter32
  qbAtmPnniPeerRcvPtseReqs Counter32
  qbAtmPnniPeerXmtPtseReqs Counter32
  qbAtmPnniPeerRcvPtseAcks Counter32
  qbAtmPnniPeerXmtPtseAcks Counter32

QbAtmPnniNodePglEntry  
SEQUENCE    
  qbAtmPnniNodePglLeadershipPriority INTEGER
  qbAtmPnniNodeCfgParentNodeIndex Integer32
  qbAtmPnniNodePglInitTime Integer32
  qbAtmPnniNodePglOverrideDelay Integer32
  qbAtmPnniNodePglReelectTime Integer32
  qbAtmPnniNodePglState INTEGER
  qbAtmPnniNodePreferredPgl QbAtmPnniNodeId
  qbAtmPnniNodePeerGroupLeader QbAtmPnniNodeId
  qbAtmPnniNodePglTimeStamp TimeStamp
  qbAtmPnniNodeActiveParentNodeId QbAtmPnniNodeId

QbAtmPnniNodeTimerEntry  
SEQUENCE    
  qbAtmPnniNodePtseHolddown Integer32
  qbAtmPnniNodeHelloHolddown Integer32
  qbAtmPnniNodeHelloInterval Integer32
  qbAtmPnniNodeHelloInactivityFactor Integer32
  qbAtmPnniNodeHlinkInact Integer32
  qbAtmPnniNodePtseRefreshInterval Integer32
  qbAtmPnniNodePtseLifetimeFactor INTEGER
  qbAtmPnniNodeRxmtInterval Integer32
  qbAtmPnniNodePeerDelayedAckInterval Integer32
  qbAtmPnniNodeAvcrPm INTEGER
  qbAtmPnniNodeAvcrMt INTEGER
  qbAtmPnniNodeCdvPm INTEGER
  qbAtmPnniNodeCtdPm INTEGER

QbAtmPnniLinkEntry  
SEQUENCE    
  qbAtmPnniLinkPortId Integer32
  qbAtmPnniLinkType INTEGER
  qbAtmPnniLinkHelloState QbAtmPnniHelloState

QbAtmHiddenVclEntry  
SEQUENCE    
  qbAtmHiddenVclName DisplayString
  qbAtmHiddenVclType INTEGER
  qbAtmHiddenVclIfIndex InterfaceIndex
  qbAtmHiddenVclVtIndex INTEGER

QbAtmInterfaceStatEntry  
SEQUENCE    
  qbAtmInterfaceStatTxOAMCells Counter32
  qbAtmInterfaceStatRxOAMCells Counter32

QbAtmInBandMgtEntry  
SEQUENCE    
  qbAtmInBandMgtIpAddr IpAddress
  qbAtmInBandMgtIpMask IpAddress
  qbAtmInBandMgtIpIfIndex InterfaceIndex
  qbAtmInBandMgtNeighborIp IpAddress
  qbAtmInBandMgtIfIndex InterfaceIndex
  qbAtmInBandMgtVpi AtmVpIdentifier
  qbAtmInBandMgtVci AtmVcIdentifier
  qbAtmInBandMgtConnKind AtmConnKind
  qbAtmInBandMgtTxTd AtmTrafficDescrParamIndex
  qbAtmInBandMgtRxTd AtmTrafficDescrParamIndex
  qbAtmInBandMgtTargetNsapAddr AtmAddr
  qbAtmInBandMgtRowStatus RowStatus

Defined Values

qbAtmMIB 1.3.6.1.4.1.4323.2.7
This module defines additional objects for management of ATM links in Quantum Bridge devices, above and beyond what is defined in the standard ATM mib, and proposed drafts.
MODULE-IDENTITY    

qbAtmObjects 1.3.6.1.4.1.4323.2.7.1
OBJECT IDENTIFIER    

qbAtmConformance 1.3.6.1.4.1.4323.2.7.2
OBJECT IDENTIFIER    

qbAtmBaseGroup 1.3.6.1.4.1.4323.2.7.3
OBJECT IDENTIFIER    

qbAtmF4F5LLID 1.3.6.1.4.1.4323.2.7.3.1
This object stores Loopback Location ID (LLID).
Status: current Access: read-write
OBJECT-TYPE    
  OCTET STRING Size(1..16)  

qbAtmDefaultPCBE 1.3.6.1.4.1.4323.2.7.3.2
This object stores the default atm cell tax to be used by the system.
Status: current Access: read-write
OBJECT-TYPE    
  INTEGER 10..70  

qbAtmInterfaceConfTable 1.3.6.1.4.1.4323.2.7.1.1
The Quantum Bridge ATM Interface Configuration Table contains extensions to the ATM Interface Configuration Table, one entry per ATM interface.
Status: current Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    QbAtmInterfaceConfEntry

qbAtmInterfaceConfEntry 1.3.6.1.4.1.4323.2.7.1.1.1
An entry in the Quantum ATM Interface Configuration Table. Every ATM interface contains a corresponding entry in the table.
Status: current Access: not-accessible
OBJECT-TYPE    
  QbAtmInterfaceConfEntry  

qbAtmInterfaceConfPolicingStatus 1.3.6.1.4.1.4323.2.7.1.1.1.1
If this object is set to 'enable' the policing is enabled on this interface. If the object set to 'disable,' the policing is disabled. Note: policing can be set on the S622 and 155 cards only.
Status: current Access: read-write
OBJECT-TYPE    
  INTEGER enable(1), disable(2)  

qbAtmInterfaceConfMaxPvcVpi 1.3.6.1.4.1.4323.2.7.1.1.1.2
This object indicates the maximum value of VPI that can be used to create a VC on a given ATM native interface.
Status: current Access: read-only
OBJECT-TYPE    
  INTEGER  

qbAtmInterfaceConfMinPvcVpi 1.3.6.1.4.1.4323.2.7.1.1.1.3
This object indicates the minimum value of VPI that can be used to create a VC on a given ATM native interface.
Status: current Access: read-only
OBJECT-TYPE    
  INTEGER  

qbAtmInterfaceConfMaxPvcVci 1.3.6.1.4.1.4323.2.7.1.1.1.4
This object indicates the maximum value of VCI that can be used to create a VC on a given ATM native interface.
Status: current Access: read-only
OBJECT-TYPE    
  INTEGER  

qbAtmInterfaceConfMinPvcVci 1.3.6.1.4.1.4323.2.7.1.1.1.5
This object indicates the minimum value of VCI that can be used to create a VC on a given ATM native interface.
Status: current Access: read-only
OBJECT-TYPE    
  INTEGER  

qbAtmInterfaceConfMaxPvpVpi 1.3.6.1.4.1.4323.2.7.1.1.1.6
This object indicates the maximum value of VPI that can be used to create a VP on a given ATM native interface.
Status: current Access: read-only
OBJECT-TYPE    
  INTEGER  

qbAtmInterfaceConfMinPvpVpi 1.3.6.1.4.1.4323.2.7.1.1.1.7
This object indicates the minimum value of VPI that can be used to create a VP on a given ATM native interface.
Status: current Access: read-only
OBJECT-TYPE    
  INTEGER  

qbAtmTrafficDescrParamTable 1.3.6.1.4.1.4323.2.7.1.2
The Quantum Bridge ATM Traffic Descriptor Table contains extensions to the ATM Traffic Descriptor Table.
Status: current Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    QbAtmTrafficDescrParamEntry

qbAtmTrafficDescrParamEntry 1.3.6.1.4.1.4323.2.7.1.2.1
An entry in the Quantum Bridge ATM Traffic Descriptor Table.
Status: current Access: not-accessible
OBJECT-TYPE    
  QbAtmTrafficDescrParamEntry  

qbAtmTrafficDescrParamName 1.3.6.1.4.1.4323.2.7.1.2.1.1
A textual description of the traffic descriptor.
Status: current Access: read-create
OBJECT-TYPE    
  DisplayString Size(0..20)  

qbAtmTrafficDescrParamDefault 1.3.6.1.4.1.4323.2.7.1.2.1.2
The object indicates whether or not this is a default traffic descriptor. Traffic descriptor with indexes from 1 to 20 are default traffic descriptors and cannot be deleted.
Status: current Access: read-only
OBJECT-TYPE    
  Boolean  

qbAtmVclTable 1.3.6.1.4.1.4323.2.7.1.3
The Quantum Bridge Table contains an extension to the atmVclConnectTable, An entry in this table models VCLs.
Status: current Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    QbAtmVclEntry

qbAtmVclEntry 1.3.6.1.4.1.4323.2.7.1.3.1
An entry in the QB ATM atmVclConnectTable.
Status: current Access: not-accessible
OBJECT-TYPE    
  QbAtmVclEntry  

qbAtmVclLoopback 1.3.6.1.4.1.4323.2.7.1.3.1.1
Enable loopback on this ATM VCL
Status: current Access: read-write
OBJECT-TYPE    
  QbEnableStatus  

qbAtmVclF4F5LoopbackInsert 1.3.6.1.4.1.4323.2.7.1.3.1.2
This is a loopback Insert object for LLID. Start loopback Insert by setting this to an LLID value.
Status: current Access: read-write
OBJECT-TYPE    
  OCTET STRING Size(16)  

qbAtmVclF4F5LoopbackStatus 1.3.6.1.4.1.4323.2.7.1.3.1.3
Status of loopback Insert command: in-progress, success, timeout.
Status: current Access: read-only
OBJECT-TYPE    
  QbF4F5LoopbackStatus  

qbAtmVclF4F5LoopbackTimestamp 1.3.6.1.4.1.4323.2.7.1.3.1.4
Value of sysUptime when last Insert completed.
Status: current Access: read-only
OBJECT-TYPE    
  TimeStamp  

qbAtmVclMgmtIpAddr 1.3.6.1.4.1.4323.2.7.1.3.1.5
Active IP Address for in-band Management SNMP of this chassis.
Status: current Access: read-write
OBJECT-TYPE    
  IpAddress  

qbAtmVclMgmtIpMask 1.3.6.1.4.1.4323.2.7.1.3.1.6
This is the IP network mask associated with the in-band Management interface.
Status: current Access: read-write
OBJECT-TYPE    
  IpAddress  

qbAtmVclMgmtNeighborIP 1.3.6.1.4.1.4323.2.7.1.3.1.7
This is the neighbor IP address associated with the in-band Management interface.
Status: current Access: read-write
OBJECT-TYPE    
  IpAddress  

qbAtmVclConnKind 1.3.6.1.4.1.4323.2.7.1.3.1.8
The VCL connection type.
Status: current Access: read-only
OBJECT-TYPE    
  QbPvcConnKind  

qbAtmVclF4F5TxStatus 1.3.6.1.4.1.4323.2.7.1.3.1.9
The transmitted OAM status for the PVC.
Status: current Access: read-only
OBJECT-TYPE    
  QbF4F5Status  

qbAtmVclF4F5TxLastChange 1.3.6.1.4.1.4323.2.7.1.3.1.10
The value of sysUPtime when qbAtmVclF4F5TxStatus last changed.
Status: current Access: read-only
OBJECT-TYPE    
  TimeStamp  

qbAtmVclF4F5RxStatus 1.3.6.1.4.1.4323.2.7.1.3.1.11
The received OAM status of the PVC.
Status: current Access: read-only
OBJECT-TYPE    
  QbF4F5Status  

qbAtmVclF4F5RxLastChange 1.3.6.1.4.1.4323.2.7.1.3.1.12
The value of sysUPtime when qbAtmVclF4F5TxStatus last changed.
Status: current Access: read-only
OBJECT-TYPE    
  TimeStamp  

qbAtmVplTable 1.3.6.1.4.1.4323.2.7.1.4
The Quantum Bridge Table contains an extension to the atmVclConnectTable, An entry in this table models VPLs.
Status: current Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    QbAtmVplEntry

qbAtmVplEntry 1.3.6.1.4.1.4323.2.7.1.4.1
An entry in the QB ATM qbAtmVpTable.
Status: current Access: not-accessible
OBJECT-TYPE    
  QbAtmVplEntry  

qbAtmVplLoopback 1.3.6.1.4.1.4323.2.7.1.4.1.1
Enable loopback on this ATM VPL
Status: current Access: read-write
OBJECT-TYPE    
  QbEnableStatus  

qbAtmVplF4F5LoopbackInsert 1.3.6.1.4.1.4323.2.7.1.4.1.2
This is a loopback Insert object for LLID. Start loopback Insert by setting this to an LLID value.
Status: current Access: read-write
OBJECT-TYPE    
  OCTET STRING Size(16)  

qbAtmVplF4F5LoopbackStatus 1.3.6.1.4.1.4323.2.7.1.4.1.3
Status of loopback Insert command: in-progress, success, timeout.
Status: current Access: read-only
OBJECT-TYPE    
  QbF4F5LoopbackStatus  

qbAtmVplF4F5LoopbackTimestamp 1.3.6.1.4.1.4323.2.7.1.4.1.4
Value of sysUptime when last Insert completed.
Status: current Access: read-only
OBJECT-TYPE    
  TimeStamp  

qbAtmVplF4F5TxStatus 1.3.6.1.4.1.4323.2.7.1.4.1.5
The transmitted OAM status for the PVP.
Status: current Access: read-only
OBJECT-TYPE    
  QbF4F5Status  

qbAtmVplF4F5TxLastChange 1.3.6.1.4.1.4323.2.7.1.4.1.6
The value of sysUPtime when qbAtmVclF4F5TxStatus last changed.
Status: current Access: read-only
OBJECT-TYPE    
  TimeStamp  

qbAtmVplF4F5RxStatus 1.3.6.1.4.1.4323.2.7.1.4.1.7
The received OAM status of the PVP.
Status: current Access: read-only
OBJECT-TYPE    
  QbF4F5Status  

qbAtmVplF4F5RxLastChange 1.3.6.1.4.1.4323.2.7.1.4.1.8
The value of sysUPtime when qbAtmVclF4F5TxStatus last changed.
Status: current Access: read-only
OBJECT-TYPE    
  TimeStamp  

qbAtmVcCrossConnectTable 1.3.6.1.4.1.4323.2.7.1.5
The Quantum Bridge Table contains an extension to the atmVcCrossConnectTable, An entry in this table models two cross-connected VCLs.
Status: current Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    QbAtmVcCrossConnectEntry

qbAtmVcCrossConnectEntry 1.3.6.1.4.1.4323.2.7.1.5.1
An entry in the QB ATM atmVcCrossConnectTable.
Status: current Access: not-accessible
OBJECT-TYPE    
  QbAtmVcCrossConnectEntry  

qbAtmVcCrossConnectName 1.3.6.1.4.1.4323.2.7.1.5.1.1
A textual description for the cross connect.
Status: current Access: read-create
OBJECT-TYPE    
  DisplayString Size(0..20)  

qbAtmVcCrossConnectRxTrafficDescrIndex 1.3.6.1.4.1.4323.2.7.1.5.1.2
The value of this object identifies the row in the ATM Traffic Descriptor Table which applies to the receive direction of this VCLs cross-connect.
Status: current Access: read-create
OBJECT-TYPE    
  AtmTrafficDescrParamIndex  

qbAtmVcCrossConnectTxTrafficDescrIndex 1.3.6.1.4.1.4323.2.7.1.5.1.3
The value of this object identifies the row of the ATM Traffic Descriptor Table which applies to the transmit direction of this VCLs cross-connect
Status: current Access: read-create
OBJECT-TYPE    
  AtmTrafficDescrParamIndex  

qbAtmVpCrossConnectTable 1.3.6.1.4.1.4323.2.7.1.6
The Quantum Bridge Table contains an extension to the atmVpCrossConnectTable, An entry in this table models two cross-connected VPLs.
Status: current Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    QbAtmVpCrossConnectEntry

qbAtmVpCrossConnectEntry 1.3.6.1.4.1.4323.2.7.1.6.1
An entry in the QB ATM atmVpCrossConnectTable.
Status: current Access: not-accessible
OBJECT-TYPE    
  QbAtmVpCrossConnectEntry  

qbAtmVpCrossConnectName 1.3.6.1.4.1.4323.2.7.1.6.1.1
A textual description for the cross connect.
Status: current Access: read-create
OBJECT-TYPE    
  DisplayString Size(0..20)  

qbAtmVpCrossConnectRxTrafficDescrIndex 1.3.6.1.4.1.4323.2.7.1.6.1.2
The value of this object identifies the row in the ATM Traffic Descriptor Table which applies to the receive direction of this VPLs cross-connect.
Status: current Access: read-create
OBJECT-TYPE    
  AtmTrafficDescrParamIndex  

qbAtmVpCrossConnectTxTrafficDescrIndex 1.3.6.1.4.1.4323.2.7.1.6.1.3
The value of this object identifies the row of the ATM Traffic Descriptor Table which applies to the transmit direction of this VPLs cross-connect
Status: current Access: read-create
OBJECT-TYPE    
  AtmTrafficDescrParamIndex  

qbAtmSigGroup 1.3.6.1.4.1.4323.2.7.1.7
OBJECT IDENTIFIER    

qbAtmPnniNodeTable 1.3.6.1.4.1.4323.2.7.1.7.1
The QbAtmpnniNodeTable contains attributes that affect the operation of a PNNI logical node. There is a single row in this table for each PNNI peer group that the managed system is expected or eligible to become a member of.
Status: current Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    QbAtmPnniNodeEntry

qbAtmPnniNodeEntry 1.3.6.1.4.1.4323.2.7.1.7.1.1
An entry in the table, containing information about a PNNI logical node in this switching system.
Status: current Access: not-accessible
OBJECT-TYPE    
  QbAtmPnniNodeEntry  

qbAtmPnniNodeIndex 1.3.6.1.4.1.4323.2.7.1.7.1.1.1
A value assigned to a node in this switching system that uniquely identifies it in the MIB.
Status: current Access: not-accessible
OBJECT-TYPE    
  INTEGER 0..65535  

qbAtmPnniNodeNetAddrPrefix 1.3.6.1.4.1.4323.2.7.1.7.1.1.2
Indicates the Network Prefix to use for the ATM End System Address. The value is 13 bytes long, and is specified in the hexadecimal format. If less than 13 bytes(26 chars) are received, the agent appends trailing zero's. The object can be set to ''h, if PNNI protocol is desirable on all interfaces.
Status: current Access: read-create
OBJECT-TYPE    
  OCTET STRING Size(13)  

qbAtmPnniNodeEndSysId 1.3.6.1.4.1.4323.2.7.1.7.1.1.3
Indicates the End System Identifier for ATM End System Address. The value is 7 bytes long, and is specified in the hexadecimal format. The object can be set to ''h, if PNNI protocol is desirable on all interfaces.
Status: current Access: read-create
OBJECT-TYPE    
  OCTET STRING Size(7)  

qbAtmPnniNodeLevel 1.3.6.1.4.1.4323.2.7.1.7.1.1.4
The level of PNNI hierarchy at which this node exists. This attribute is used to determine the default node ID and the default peer group ID for this node. This object may only be written when pnniNodeAdminStatus has the value down.
Status: current Access: read-create
OBJECT-TYPE    
  INTEGER 1..104  

qbAtmPnniNodeRowStatus 1.3.6.1.4.1.4323.2.7.1.7.1.1.5
To create, delete, activate and de-activate a Node. Setting this object to createAndGo(4) causes the corresponding row to be created. Setting this object to destroy(6) causes the corresponding row to be deleted. Note that -- currently-- only a single instance of a row can be created in this table.
Status: current Access: read-create
OBJECT-TYPE    
  RowStatus  

qbAtmPnniNodeOperStatus 1.3.6.1.4.1.4323.2.7.1.7.1.1.6
Indicates the Operational Status of the PNNI Node. For Logical Group Nodes, the Operational Status will be up only if the child becomes the PGL.
Status: current Access: read-only
OBJECT-TYPE    
  INTEGER up(1), down(2)  

qbAtmPnniNodeAtmAddress 1.3.6.1.4.1.4323.2.7.1.7.1.1.7
This node's ATM End System Address. Remote systems wishing to exchange PNNI protocol packets with this node should direct packets or calls to this address. The current Qb implementation does not support writing this value.
Status: current Access: read-only
OBJECT-TYPE    
  QbAtmPnniAtmAddr  

qbAtmPnniNodePeerGroupId 1.3.6.1.4.1.4323.2.7.1.7.1.1.8
The Peer Group Identifier of the peer group that the given node is to become a member of.
Status: current Access: read-only
OBJECT-TYPE    
  QbAtmPnniPeerGroupId  

qbAtmPnniIfTable 1.3.6.1.4.1.4323.2.7.1.7.2
The qbAtmPnniIfTable contains the attributes necessary to configure a physical interface on a switching system capable of being used for PNNI routing. An ifIndex is used as the instance ID to uniquely identify the interface on the local switching system. This index has the same value as the ifIndex object defined in RFC 1573 for the same interface, since this table correlates with the ifTable in RFC 1573. One row in this table is created by the managed system for each row in the ifTable that has an ifType of atm(37) or atmLogical(80).
Status: current Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    QbAtmPnniIfEntry

qbAtmPnniIfEntry 1.3.6.1.4.1.4323.2.7.1.7.2.1
An entry in the table, containing PNNI specific interface information in this switching system.
Status: current Access: not-accessible
OBJECT-TYPE    
  QbAtmPnniIfEntry  

qbAtmPnniIfNodeIndex 1.3.6.1.4.1.4323.2.7.1.7.2.1.1
Identifies the node within the switching system that the interface is directly attached to. Note: For this release this value can be set only to 1.
Status: current Access: read-write
OBJECT-TYPE    
  INTEGER 1..1  

qbAtmPnniIfAdmWeightCbr 1.3.6.1.4.1.4323.2.7.1.7.2.1.2
The administrative weight of this interface for the constant bit rate service category.
Status: current Access: read-write
OBJECT-TYPE    
  QbAtmPnniWeight  

qbAtmPnniIfAdmWeightRtVbr 1.3.6.1.4.1.4323.2.7.1.7.2.1.3
The administrative weight of this interface for the real-time variable bit rate service category.
Status: current Access: read-write
OBJECT-TYPE    
  QbAtmPnniWeight  

qbAtmPnniIfAdmWeightNrtVbr 1.3.6.1.4.1.4323.2.7.1.7.2.1.4
The administrative weight of this interface for the non-real-time variable bit rate service category.
Status: current Access: read-write
OBJECT-TYPE    
  QbAtmPnniWeight  

qbAtmPnniIfAdmWeightAbr 1.3.6.1.4.1.4323.2.7.1.7.2.1.5
The administrative weight of this interface for the available bit rate service category.
Status: current Access: read-write
OBJECT-TYPE    
  QbAtmPnniWeight  

qbAtmPnniIfAdmWeightUbr 1.3.6.1.4.1.4323.2.7.1.7.2.1.6
The administrative weight of this interface for the unspecified bit rate service category.
Status: current Access: read-write
OBJECT-TYPE    
  QbAtmPnniWeight  

qbAtmPnniIfRccServiceCategory 1.3.6.1.4.1.4323.2.7.1.7.2.1.7
The service category used for the PNNI routing control channel (VCI=18) on this interface.
Status: current Access: read-write
OBJECT-TYPE    
  AtmServiceCategory  

qbAtmPnniIfRccTrafficDescrIndex 1.3.6.1.4.1.4323.2.7.1.7.2.1.8
The traffic descriptor index referring to the entry in the atmTrafficDescrParamTable defined in RFC 1695 that specifies the traffic allocation for the PNNI routing control channel (VCI=18) on this interface.
Status: current Access: read-write
OBJECT-TYPE    
  AtmTrafficDescrParamIndex  

qbAtmPnniIfPolicingStatus 1.3.6.1.4.1.4323.2.7.1.7.2.1.9
If this object is set to enable, the policing is enabled on this interface. If the object is set to 'disable' the policing is disabled.
Status: deprecated Access: read-write
OBJECT-TYPE    
  INTEGER enable(1), disable(2)  

qbAtmPnniRouteAddrTable 1.3.6.1.4.1.4323.2.7.1.7.3
A table containing all the attributes necessary to determine what the PNNI entity believes is reachable in terms of ATM End System Addresses, and to determine which nodes are advertising this reachability. This table is also used to configure static routes to reachable address prefixes. The local node index that receives the reachability information, reachable address, address prefix length, and an index that distinguishes between multiple listings of connectivity to a given address prefix from a given local node are combined to form an instance ID for this object.
Status: current Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    QbAtmPnniRouteAddrEntry

qbAtmPnniRouteAddrEntry 1.3.6.1.4.1.4323.2.7.1.7.3.1
An entry in the table, containing information about a reachable address prefix.
Status: current Access: not-accessible
OBJECT-TYPE    
  QbAtmPnniRouteAddrEntry  

qbAtmPnniRouteAddrIfIndex 1.3.6.1.4.1.4323.2.7.1.7.3.1.1
The local interface over which the reachable address can be reached.
Status: current Access: not-accessible
OBJECT-TYPE    
  InterfaceIndex  

qbAtmPnniRouteAddrAddress 1.3.6.1.4.1.4323.2.7.1.7.3.1.2
The value of the ATM End System Address prefix.
Status: current Access: not-accessible
OBJECT-TYPE    
  OCTET STRING Size(19)  

qbAtmPnniRouteAddrPrefixLength 1.3.6.1.4.1.4323.2.7.1.7.3.1.3
Indicates the number of bits to be applied to the ATM End System Address prefix.
Status: current Access: read-create
OBJECT-TYPE    
  INTEGER 1..152  

qbAtmPnniRouteAddrRowStatus 1.3.6.1.4.1.4323.2.7.1.7.3.1.4
To create, delete, activate and de-activate a reachable address prefix.
Status: current Access: read-create
OBJECT-TYPE    
  RowStatus  

qbAtmPnniRouteAddrProto 1.3.6.1.4.1.4323.2.7.1.7.3.1.5
This object indicates the Routing mechanism through which the connectivity from the advertising node to the reachable address prefix was learned.
Status: current Access: read-only
OBJECT-TYPE    
  INTEGER iisp(1), pnni(2)  

qbAtmInterfaceConfSigTable 1.3.6.1.4.1.4323.2.7.1.7.4
This table contains ATM local interface configuration parameters, one entry per ATM interface port.
Status: current Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    QbAtmInterfaceConfSigEntry

qbAtmInterfaceConfSigEntry 1.3.6.1.4.1.4323.2.7.1.7.4.1
This list contains additonal ATM interface configuration parameters and state variables.
Status: current Access: not-accessible
OBJECT-TYPE    
  QbAtmInterfaceConfSigEntry  

qbAtmInterfaceConfSigMode 1.3.6.1.4.1.4323.2.7.1.7.4.1.1
The type of ATM interface which is either a UNI (User to Network), PNNI or IISP. To modify the qbAtmInterfaceConfSignType, ifAdminStatus has to be down.
Status: current Access: read-write
OBJECT-TYPE    
  QbAtmSigSpec  

qbAtmInterfaceConfSigSide 1.3.6.1.4.1.4323.2.7.1.7.4.1.2
The side of ATM interface which is either a user or network side. NotApplicable value implies that qbAtmInterfaceConfSignType is other than uni or iisp.
Status: current Access: read-write
OBJECT-TYPE    
  INTEGER user(1), network(2), notApplicable(3)  

qbAtmInterfaceConfSigParseMode 1.3.6.1.4.1.4323.2.7.1.7.4.1.3
Indicates to the signalling stack to use strict parsing of the INformation Elements (IEs) within signalling messages. This parameter is set to 'on' for conformance testing. For systems that do not test conformance it is recommended to set the object to 'off'.
Status: current Access: read-write
OBJECT-TYPE    
  INTEGER on(1), off(2)  

qbAtmInterfaceConfSigAdminStatus 1.3.6.1.4.1.4323.2.7.1.7.4.1.4
Enable/Disable signalling/sscop on this interface. To modify the qbAtmInterfaceConfSignAdminStatus, ifAdminStatus has to be down.
Status: current Access: read-write
OBJECT-TYPE    
  INTEGER enabled(1), disabled(2)  

qbAtmInterfaceConfSigSvcMinVci 1.3.6.1.4.1.4323.2.7.1.7.4.1.5
The minimum value of SVC connection for vci.
Status: current Access: read-write
OBJECT-TYPE    
  INTEGER 32..16383  

qbAtmInterfaceConfSigSvcMaxVci 1.3.6.1.4.1.4323.2.7.1.7.4.1.6
The maximum value of SVC connection for vci.
Status: current Access: read-write
OBJECT-TYPE    
  INTEGER 32..16383  

qbAtmInterfaceConfSigSvcMinVpi 1.3.6.1.4.1.4323.2.7.1.7.4.1.7
The minimum value of SVC connection for vpi.
Status: current Access: read-write
OBJECT-TYPE    
  INTEGER 0..255  

qbAtmInterfaceConfSigSvcMaxVpi 1.3.6.1.4.1.4323.2.7.1.7.4.1.8
The maximum value of SVC connection for vpi.
Status: current Access: read-write
OBJECT-TYPE    
  INTEGER 0..255  

qbAtmInterfaceConfSigSvpMinVpi 1.3.6.1.4.1.4323.2.7.1.7.4.1.9
The minimum value of SVP connection for vpi.
Status: current Access: read-write
OBJECT-TYPE    
  INTEGER 0..255  

qbAtmInterfaceConfSigSvpMaxVpi 1.3.6.1.4.1.4323.2.7.1.7.4.1.10
The maximum value of SVP connection for vpi.
Status: current Access: read-write
OBJECT-TYPE    
  INTEGER 0..255  

qbAtmInterfaceConfSigLastChange 1.3.6.1.4.1.4323.2.7.1.7.4.1.11
The value of sysUpTime at the time this interface changed its current administrative state.
Status: current Access: read-only
OBJECT-TYPE    
  AtmVorXLastChange  

qbAtmInterfaceConfSigIlmiEnable 1.3.6.1.4.1.4323.2.7.1.7.4.1.12
Can be enabled only if signaling is configured. ILMI is enabled by default when signaling is configured on the system and the user may enter the disable option .
Status: current Access: read-write
OBJECT-TYPE    
  Boolean  

qbAtmPnniNbrPeerTable 1.3.6.1.4.1.4323.2.7.1.7.5
The qbAtmPnniNbrPeer Object contains all the attributes necessary to describe the relationship a node in this switching system has with a neighboring node within the same peer group. A concatenation of the Node Identifier of the node within the local switching system and the neighboring peer's Node Identifier is used to form the instance ID for this object. The entire qbAtmPnniNbrPeer object is read-only, reflecting the fact that neighboring peers are discovered dynamically by the PNNI protocol rather than configured.
Status: current Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    QbAtmPnniNbrPeerEntry

qbAtmPnniNbrPeerEntry 1.3.6.1.4.1.4323.2.7.1.7.5.1
An entry in the table, containing information about this node's relationship with a neighboring peer node.
Status: current Access: not-accessible
OBJECT-TYPE    
  QbAtmPnniNbrPeerEntry  

qbAtmPnniPeerRemoteNodeId 1.3.6.1.4.1.4323.2.7.1.7.5.1.1
The Node Identifier of the neighboring peer node.
Status: current Access: not-accessible
OBJECT-TYPE    
  QbAtmPnniNodeId  

qbAtmPnniPeerState 1.3.6.1.4.1.4323.2.7.1.7.5.1.2
Indicates the state of this node's Neighboring Peer State Machine associated with qbAtmPnniPeerRemoteNodeId.
Status: current Access: read-only
OBJECT-TYPE    
  INTEGER npdown(1), negotiating(2), exchanging(3), loading(4), full(5)  

qbAtmPnniPeerSvccRccIndex 1.3.6.1.4.1.4323.2.7.1.7.5.1.3
Identifies the SVCC-based RCC being used to communicate with the neighboring peer if one exists. If both the local node and the neighboring peer node are lowest-level nodes, this attribute is set to zero.
Status: current Access: read-only
OBJECT-TYPE    
  INTEGER  

qbAtmPnniPeerPortCount 1.3.6.1.4.1.4323.2.7.1.7.5.1.4
A count of the total number of ports that connect to the neighboring peer. If the neighboring peer only communicates via an SVCC-based RCC, the value of this attribute is set to zero. Otherwise it is set to the total number of ports to the neighboring peer in the Hello state 2-WayInside.
Status: current Access: read-only
OBJECT-TYPE    
  INTEGER  

qbAtmPnniPeerRcvDbSums 1.3.6.1.4.1.4323.2.7.1.7.5.1.5
A count of the number of Database Summary Packets received from the neighboring peer.
Status: current Access: read-only
OBJECT-TYPE    
  Counter32  

qbAtmPnniPeerXmtDbSums 1.3.6.1.4.1.4323.2.7.1.7.5.1.6
A count of the number of Database Summary Packets transmitted to the neighboring peer.
Status: current Access: read-only
OBJECT-TYPE    
  Counter32  

qbAtmPnniPeerRcvPtsps 1.3.6.1.4.1.4323.2.7.1.7.5.1.7
A count of the number of PTSPs received from the neighboring peer.
Status: current Access: read-only
OBJECT-TYPE    
  Counter32  

qbAtmPnniPeerXmtPtsps 1.3.6.1.4.1.4323.2.7.1.7.5.1.8
A count of the number of PTSPs (re)transmitted to the neighboring peer.
Status: current Access: read-only
OBJECT-TYPE    
  Counter32  

qbAtmPnniPeerRcvPtseReqs 1.3.6.1.4.1.4323.2.7.1.7.5.1.9
A count of the number of PTSE Request packets received from the neighboring peer.
Status: current Access: read-only
OBJECT-TYPE    
  Counter32  

qbAtmPnniPeerXmtPtseReqs 1.3.6.1.4.1.4323.2.7.1.7.5.1.10
A count of the number of PTSE Request packets transmitted to the neighboring peer.
Status: current Access: read-only
OBJECT-TYPE    
  Counter32  

qbAtmPnniPeerRcvPtseAcks 1.3.6.1.4.1.4323.2.7.1.7.5.1.11
A count of the number of PTSE Ack packets received from the neighboring peer.
Status: current Access: read-only
OBJECT-TYPE    
  Counter32  

qbAtmPnniPeerXmtPtseAcks 1.3.6.1.4.1.4323.2.7.1.7.5.1.12
A count of the number of PTSE Ack packets transmitted to the neighboring peer.
Status: current Access: read-only
OBJECT-TYPE    
  Counter32  

qbAtmPnniNodePglTable 1.3.6.1.4.1.4323.2.7.1.7.6
Peer group leader election information for a PNNI node in this switching system.
Status: current Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    QbAtmPnniNodePglEntry

qbAtmPnniNodePglEntry 1.3.6.1.4.1.4323.2.7.1.7.6.1
An entry in the table, containing PGL election information of a PNNI logical node in this switching system.
Status: current Access: not-accessible
OBJECT-TYPE    
  QbAtmPnniNodePglEntry  

qbAtmPnniNodePglLeadershipPriority 1.3.6.1.4.1.4323.2.7.1.7.6.1.1
The Leadership priority value this node should advertise in its nodal information group for the given peer group. Only the value zero can be used with nodes that are not PGL/LGN capable. If there is no configured parent node index or no corresponding entry in the pnniNodeTable, then the advertised leadership priority is zero regardless of this value.
Status: current Access: read-create
OBJECT-TYPE    
  INTEGER 0..205  

qbAtmPnniNodeCfgParentNodeIndex 1.3.6.1.4.1.4323.2.7.1.7.6.1.2
The local node index used to identify the node that will represent this peer group at the next higher level of hierarchy, if this node becomes peer group leader. The value 0 indicates that there is no parent node.
Status: current Access: read-create
OBJECT-TYPE    
  Integer32  

qbAtmPnniNodePglInitTime 1.3.6.1.4.1.4323.2.7.1.7.6.1.3
The amount of time in seconds this node will delay advertising its choice of preferred PGL after having initialized operation and reached the full state with at least one neighbor in the peer group.
Status: current Access: read-create
OBJECT-TYPE    
  Integer32  

qbAtmPnniNodePglOverrideDelay 1.3.6.1.4.1.4323.2.7.1.7.6.1.4
The amount of time in seconds a node will wait for itself to be declared the preferred PGL by unanimous agreement among its peers. In the absence of unanimous agreement this will be the amount of time that will pass before this node considers a two thirds majority as sufficient agreement to declare itself peer group leader, abandoning the attempt to get unanimous agreement.
Status: current Access: read-create
OBJECT-TYPE    
  Integer32  

qbAtmPnniNodePglReelectTime 1.3.6.1.4.1.4323.2.7.1.7.6.1.5
The amount of time in seconds after losing connectivity to the current peer group leader, that this node will wait before re-starting the process of electing a new peer group leader.
Status: current Access: read-create
OBJECT-TYPE    
  Integer32  

qbAtmPnniNodePglState 1.3.6.1.4.1.4323.2.7.1.7.6.1.6
Indicates the state that this node is in with respect to the Peer Group Leader election that takes place in the node's peer group. The values are enumerated in the Peer Group Leader State Machine.
Status: current Access: read-only
OBJECT-TYPE    
  INTEGER starting(1), awaiting(2), awaitingFull(3), initialDelay(4), calculating(5), awaitUnanimity(6), operPgl(7), operNotPgl(8), hungElection(9), awaitReElection(10), other(11)  

qbAtmPnniNodePreferredPgl 1.3.6.1.4.1.4323.2.7.1.7.6.1.7
The Node ID of the node which the local node believes should be or become the peer group leader. This is also the value the local node is currently advertising in the `Preferred Peer Group Leader Node ID' field of its nodal information group within the given peer group. If a Preferred PGL has not been chosen, this attribute's value is set to (all) zero(s).
Status: current Access: read-only
OBJECT-TYPE    
  QbAtmPnniNodeId  

qbAtmPnniNodePeerGroupLeader 1.3.6.1.4.1.4323.2.7.1.7.6.1.8
The Node Identifier of the node which is currently operating as peer group leader of the peer group this node belongs to. If a PGL has not been elected, this attribute's value is set to (all) zero(s).
Status: current Access: read-only
OBJECT-TYPE    
  QbAtmPnniNodeId  

qbAtmPnniNodePglTimeStamp 1.3.6.1.4.1.4323.2.7.1.7.6.1.9
The time at which the current Peer Group Leader established itself.
Status: current Access: read-only
OBJECT-TYPE    
  TimeStamp  

qbAtmPnniNodeActiveParentNodeId 1.3.6.1.4.1.4323.2.7.1.7.6.1.10
The Node Identifier value being used by the Peer Group Leader to represent this peer group at the next higher level of the hierarchy. If this node is at the highest level of the hierarchy or if no PGL has yet been elected the PNNI Protocol Entity sets the value of this attribute to (all) zero(s).
Status: current Access: read-only
OBJECT-TYPE    
  QbAtmPnniNodeId  

qbAtmPnniNodeTimerTable 1.3.6.1.4.1.4323.2.7.1.7.7
A table of initial PNNI timer values and significant change thresholds.
Status: current Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    QbAtmPnniNodeTimerEntry

qbAtmPnniNodeTimerEntry 1.3.6.1.4.1.4323.2.7.1.7.7.1
An entry in the table, containing initial PNNI timer values and significant change thresholds of a PNNI logical node in this switching system.
Status: current Access: not-accessible
OBJECT-TYPE    
  QbAtmPnniNodeTimerEntry  

qbAtmPnniNodePtseHolddown 1.3.6.1.4.1.4323.2.7.1.7.7.1.1
The initial value for the PTSE hold down timer that will be used by the given node to limit the rate at which it can re-originate PTSEs. It must be a positive non-zero number.
Status: current Access: read-create
OBJECT-TYPE    
  Integer32  

qbAtmPnniNodeHelloHolddown 1.3.6.1.4.1.4323.2.7.1.7.7.1.2
The initial value for the Hello hold down timer that will be used by the given node to limit the rate at which it sends Hellos. It must be a positive non-zero number.
Status: current Access: read-create
OBJECT-TYPE    
  Integer32  

qbAtmPnniNodeHelloInterval 1.3.6.1.4.1.4323.2.7.1.7.7.1.3
The initial value for the Hello Timer. In the absence of triggered Hellos, this node will send one Hello packet on each of its ports on this interval.
Status: current Access: read-create
OBJECT-TYPE    
  Integer32  

qbAtmPnniNodeHelloInactivityFactor 1.3.6.1.4.1.4323.2.7.1.7.7.1.4
The value for the Hello Inactivity factor that this node will use to determine when a neighbor has gone down.
Status: current Access: read-create
OBJECT-TYPE    
  Integer32  

qbAtmPnniNodeHlinkInact 1.3.6.1.4.1.4323.2.7.1.7.7.1.5
The amount of time a node will continue to advertise a horizontal (logical) link for which it has not received and processed a LGN Horizontal Link information group.
Status: current Access: read-create
OBJECT-TYPE    
  Integer32  

qbAtmPnniNodePtseRefreshInterval 1.3.6.1.4.1.4323.2.7.1.7.7.1.6
The initial value for the Refresh timer that this node will use to drive (re-)origination of PTSEs in the absence of triggered updates.
Status: current Access: read-create
OBJECT-TYPE    
  Integer32  

qbAtmPnniNodePtseLifetimeFactor 1.3.6.1.4.1.4323.2.7.1.7.7.1.7
The value for the lifetime multiplier, expressed as a percentage. The result of multiplying the qbAtmPnniNodePtseRefreshInterval attribute value by this attribute value is used as the initial lifetime that this node places into self-originated PTSEs.
Status: current Access: read-create
OBJECT-TYPE    
  INTEGER 101..1000  

qbAtmPnniNodeRxmtInterval 1.3.6.1.4.1.4323.2.7.1.7.7.1.8
The period between retransmissions of unacknowledged Database Summary packets, PTSE Request packets, and PTSPs.
Status: current Access: read-create
OBJECT-TYPE    
  Integer32  

qbAtmPnniNodePeerDelayedAckInterval 1.3.6.1.4.1.4323.2.7.1.7.7.1.9
The minimum amount of time between transmissions of delayed PTSE acknowledgement packets.
Status: current Access: read-create
OBJECT-TYPE    
  Integer32  

qbAtmPnniNodeAvcrPm 1.3.6.1.4.1.4323.2.7.1.7.7.1.10
The proportional multiplier used in the algorithms that determine significant change for AvCR parameters, expressed as a percentage.
Status: current Access: read-create
OBJECT-TYPE    
  INTEGER 1..99  

qbAtmPnniNodeAvcrMt 1.3.6.1.4.1.4323.2.7.1.7.7.1.11
The minimum threshold used in the algorithms that determine significant change for AvCR parameters, expressed as a percentage.
Status: current Access: read-create
OBJECT-TYPE    
  INTEGER 1..99  

qbAtmPnniNodeCdvPm 1.3.6.1.4.1.4323.2.7.1.7.7.1.12
The proportional multiplier used in the algorithms that determine significant change for CDV metrics, expressed as a percentage.
Status: current Access: read-create
OBJECT-TYPE    
  INTEGER 1..99  

qbAtmPnniNodeCtdPm 1.3.6.1.4.1.4323.2.7.1.7.7.1.13
The proportional multiplier used in the algorithms that determine significant change for CTD metrics, expressed as a percentage.
Status: current Access: read-create
OBJECT-TYPE    
  INTEGER 1..99  

qbAtmPnniLinkTable 1.3.6.1.4.1.4323.2.7.1.7.8
This table contains the attributes necessary to describe the operation of logical links attached to the local switching system and the relationship with the neighbor nodes on the other end of the links. Links are attached to a specific node within the switching system. A concatenation of the Node Index of the node within the local switching system and the port ID are used as the instance ID to uniquely identify the link. Links may represent horizontal links between lowest level neighboring peers, outside links, uplinks, or horizontal links to/from LGNs. The entire qbAtmPnniLink object is read-only, reflecting the fact that this information is discovered dynamically by the PNNI protocol rather than configured.
Status: current Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    QbAtmPnniLinkEntry

qbAtmPnniLinkEntry 1.3.6.1.4.1.4323.2.7.1.7.8.1
An entry in the table, containing information about a link attached to a PNNI logical node in this switching system.
Status: current Access: not-accessible
OBJECT-TYPE    
  QbAtmPnniLinkEntry  

qbAtmPnniLinkPortId 1.3.6.1.4.1.4323.2.7.1.7.8.1.1
The Port Identifier of the link as selected by the local node. This value has meaning only within the context of the node to which the port is attached.
Status: current Access: not-accessible
OBJECT-TYPE    
  Integer32  

qbAtmPnniLinkType 1.3.6.1.4.1.4323.2.7.1.7.8.1.2
Indicates the type of link being described.
Status: current Access: read-only
OBJECT-TYPE    
  INTEGER unknown(1), lowestLevelHorizontalLink(2), horizontalLinkToFromLgn(3), lowestLevelOutsideLink(4), uplink(5), outsideLinkAndUplink(6)  

qbAtmPnniLinkHelloState 1.3.6.1.4.1.4323.2.7.1.7.8.1.3
For horizontal and outside links between lowest-level nodes and for links of unknown type, this attribute indicates the state of the Hello protocol exchange over this link. For links to/from LGNs, this attribute indicates the state of the corresponding LGN Horizontal Link Hello State Machine. For uplinks (where the port ID is not also used for the underlying outside link), this attribute is set to notApplicable.
Status: current Access: read-only
OBJECT-TYPE    
  QbAtmPnniHelloState  

qbAtmHiddenVclTable 1.3.6.1.4.1.4323.2.7.1.8
The QB table with extensions to atmVclTable
Status: current Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    QbAtmHiddenVclEntry

qbAtmHiddenVclEntry 1.3.6.1.4.1.4323.2.7.1.8.1
Entry in qbAtmHiddenVclTable
Status: current Access: not-accessible
OBJECT-TYPE    
  QbAtmHiddenVclEntry  

qbAtmHiddenVclName 1.3.6.1.4.1.4323.2.7.1.8.1.1
A textual description for the SPVC name.
Status: current Access: read-create
OBJECT-TYPE    
  DisplayString Size(0..20)  

qbAtmHiddenVclType 1.3.6.1.4.1.4323.2.7.1.8.1.2
Value for the interface type. Native ATM - Q155, S622; non-native - E1, DS1, ENET, VT
Status: current Access: read-create
OBJECT-TYPE    
  INTEGER native(1), non-native(2)  

qbAtmHiddenVclIfIndex 1.3.6.1.4.1.4323.2.7.1.8.1.3
ifIndex value for IOT interface. This value is not used for native ATM interfaces.
Status: current Access: read-create
OBJECT-TYPE    
  InterfaceIndex  

qbAtmHiddenVclVtIndex 1.3.6.1.4.1.4323.2.7.1.8.1.4
Address information for a VT card. This value is used for VT cards only.
Status: current Access: read-create
OBJECT-TYPE    
  INTEGER  

qbAtmSwitchModuleGroup 1.3.6.1.4.1.4323.2.7.1.9
OBJECT IDENTIFIER    

qbAtmStatsBuffOverCells 1.3.6.1.4.1.4323.2.7.1.9.1
This object gives the number of cells discarded due to buffer overflows.
Status: current Access: read-only
OBJECT-TYPE    
  Counter32  

qbAtmStatsInvalidCells 1.3.6.1.4.1.4323.2.7.1.9.2
This object gives the number of cells discarded due to unknown VPI/VCI.
Status: current Access: read-only
OBJECT-TYPE    
  Counter32  

qbAtmStatsInvUpdateCells 1.3.6.1.4.1.4323.2.7.1.9.3
This object gives the number of cells discarded due to internal switch errors.
Status: current Access: read-only
OBJECT-TYPE    
  Counter32  

qbAtmInterfaceStatTable 1.3.6.1.4.1.4323.2.7.1.10
The Quantum Bridge ATM Interface Statistic Table contains ATM layer statistics for each ATM interface.
Status: current Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    QbAtmInterfaceStatEntry

qbAtmInterfaceStatEntry 1.3.6.1.4.1.4323.2.7.1.10.1
An entry in the Quantum ATM Interface Table. Every ATM interface contains a corresponding entry in the table.
Status: current Access: not-accessible
OBJECT-TYPE    
  QbAtmInterfaceStatEntry  

qbAtmInterfaceStatTxOAMCells 1.3.6.1.4.1.4323.2.7.1.10.1.1
The total number of valid OAM cells transmitted by this atm layer interface.
Status: current Access: read-only
OBJECT-TYPE    
  Counter32  

qbAtmInterfaceStatRxOAMCells 1.3.6.1.4.1.4323.2.7.1.10.1.2
The total number of OAS ATM cells received by this atm layer interface.
Status: current Access: read-only
OBJECT-TYPE    
  Counter32  

qbAtmInBandMgtTable 1.3.6.1.4.1.4323.2.7.1.11
The QbAtmInBandMgtTable defines in-band Management IP channels for use by ATM connections.
Status: current Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    QbAtmInBandMgtEntry

qbAtmTrafficDescriptorTypes 1.3.6.1.4.1.4323.2.7.1.12
OBJECT IDENTIFIER    

qbAtmPkt 1.3.6.1.4.1.4323.2.7.1.12.1
This traffic descriptor type is to define a connection with an Ethernet endpoint, and it is for a user that does not want to use ATM parameters directly. The EtherNet bandwidth will be converted to a nrtVbr traffic descriptor. The conversion from Ethernet bandwidth to ATM cell rate must add an ATM cell tax. This is defined using the pcbe (packet-to-cell bandwidth expansion) factor. If this is not defined for the traffic descriptor, then the system default (qbAtmDefaultPCBE)should be used. The use of the parameter vector for this type: Parameter 1: minbw, the minimum guarnteed bandwidth fo rthe connection. This is defined in Mb/sec. (0-100). Parameter 2: maxbw, the maximum bursting capability of the connection. This is defined in Mb/sec (1-100). It is default to minbw. Parameter 3: bw, indicates the bandwidth for the PON segment. Vaules are expressed in Mb, and may take interger value between 1 and 100. (only apply to 155Mb PON). It is default to minbw. Parameter 4: pcbe, it defines the packed-to-cell bandwidth expansion. This is the percentage overhead that is used to convert Ethernet bandwidth to ATM cell rates. It is default to qbAtmDefaultPCBE. Parameter 5: not used.
Status: current Access: not-accessible
OBJECT-IDENTITY    

qbAtmInBandMgtEntry 1.3.6.1.4.1.4323.2.7.1.11.1
An entry in the table, containing information about an in-band Management channel.
Status: current Access: not-accessible
OBJECT-TYPE    
  QbAtmInBandMgtEntry  

qbAtmInBandMgtIpAddr 1.3.6.1.4.1.4323.2.7.1.11.1.1
An IP Address for in-band SNMP Management of this chassis.
Status: current Access: not-accessible
OBJECT-TYPE    
  IpAddress  

qbAtmInBandMgtIpMask 1.3.6.1.4.1.4323.2.7.1.11.1.2
The IP Network Mask associated with this in-band SNMP Management IP Address.
Status: current Access: read-create
OBJECT-TYPE    
  IpAddress  

qbAtmInBandMgtIpIfIndex 1.3.6.1.4.1.4323.2.7.1.11.1.3
The Interface associated with this in-band management address.
Status: current Access: read-create
OBJECT-TYPE    
  InterfaceIndex  

qbAtmInBandMgtNeighborIp 1.3.6.1.4.1.4323.2.7.1.11.1.4
This is the neighbor IP address associated with the in-band Management Interface. If the qbAtmInBandMgtConnKind is any value other than pvc(1), this object is non-applicable.
Status: current Access: read-create
OBJECT-TYPE    
  IpAddress  

qbAtmInBandMgtIfIndex 1.3.6.1.4.1.4323.2.7.1.11.1.5
This is the interface index associated with the in-band Management connection. If the qbAtmInBandMgtConnKind is any value other than pvc(1), this object is non-applicable.
Status: current Access: read-create
OBJECT-TYPE    
  InterfaceIndex  

qbAtmInBandMgtVpi 1.3.6.1.4.1.4323.2.7.1.11.1.6
If the value of qbAtmInBandMgtConnKind is pvc(1), this is the VPI associated with this in-band management connection. If the value of qbAtmInBandMgtConnKind is spvcInitiator(4), this object is target VPI. In all other cases, the value of this object is non-applicable.
Status: current Access: read-create
OBJECT-TYPE    
  AtmVpIdentifier  

qbAtmInBandMgtVci 1.3.6.1.4.1.4323.2.7.1.11.1.7
If the value of qbAtmInBandMgtConnKind is pvc(1), this is the VCI associated with this in-band management connection. If the value of qbAtmInBandMgtConnKind is spvcInitiator(4), this object is target VCI. In all other cases, the value of this object is non-applicable.
Status: current Access: read-create
OBJECT-TYPE    
  AtmVcIdentifier  

qbAtmInBandMgtConnKind 1.3.6.1.4.1.4323.2.7.1.11.1.8
This is the connection type associated with the in-band Management connection. The currently accepted types are pvc(1), spvcInitiator(4) and spvcTarget(5).
Status: current Access: read-create
OBJECT-TYPE    
  AtmConnKind  

qbAtmInBandMgtTxTd 1.3.6.1.4.1.4323.2.7.1.11.1.9
The Transmit traffic descriptor associated with this in-band management channel.
Status: current Access: read-create
OBJECT-TYPE    
  AtmTrafficDescrParamIndex  

qbAtmInBandMgtRxTd 1.3.6.1.4.1.4323.2.7.1.11.1.10
The Receive traffic descriptor associated with this in-band management channel.
Status: current Access: read-create
OBJECT-TYPE    
  AtmTrafficDescrParamIndex  

qbAtmInBandMgtTargetNsapAddr 1.3.6.1.4.1.4323.2.7.1.11.1.11
If the value of qbAtmInBandMgtConnKind is spvcInitiator(4) this object represetns the Target NSAP Address of the connection. In all other cases, the value of this object is non-applicable.
Status: current Access: read-create
OBJECT-TYPE    
  AtmAddr  

qbAtmInBandMgtRowStatus 1.3.6.1.4.1.4323.2.7.1.11.1.12
To create, or delete an Entry in this table. Setting this object to createAndGo(4) causes the corresponding row to be created. Setting this object to destroy(6) causes the corresponding row to be deleted. Note that -- currently-- only a single instance of a row can be created in this table.
Status: current Access: read-create
OBJECT-TYPE    
  RowStatus  

qbAtmCompliances 1.3.6.1.4.1.4323.2.7.2.1
OBJECT IDENTIFIER    

qbAtmGroups 1.3.6.1.4.1.4323.2.7.2.2
OBJECT IDENTIFIER    

qbAtmCompliance 1.3.6.1.4.1.4323.2.7.2.1.1
The compliance statement for all agents that support this MIB. A compliant agent implements all objects defined in this MIB.
Status: current Access: read-create
MODULE-COMPLIANCE    

qbAtmInterfaceConfGroupInfo 1.3.6.1.4.1.4323.2.7.2.2.1
The set of all accessible objects in the Interface group of this MIB.
Status: current Access: read-create
OBJECT-GROUP    

qbAtmTrafficDescrParamGroupInfo 1.3.6.1.4.1.4323.2.7.2.2.2
The set of all accessible objects in the Traffic group of this MIB.
Status: current Access: read-create
OBJECT-GROUP    

qbAtmVclGroupInfo 1.3.6.1.4.1.4323.2.7.2.2.3
The set of all accessible objects in the VCL group of this MIB.
Status: current Access: read-create
OBJECT-GROUP    

qbAtmVplGroupInfo 1.3.6.1.4.1.4323.2.7.2.2.4
The set of all accessible objects in the VPL group of this MIB.
Status: current Access: read-create
OBJECT-GROUP    

qbAtmVcCrossConnectGroupInfo 1.3.6.1.4.1.4323.2.7.2.2.5
The set of all accessible objects in the VPL group of this MIB.
Status: current Access: read-create
OBJECT-GROUP    

qbAtmVpCrossConnectGroupInfo 1.3.6.1.4.1.4323.2.7.2.2.6
The set of all accessible objects in the VPL group of this MIB.
Status: current Access: read-create
OBJECT-GROUP    

qbAtmPnniNodeGroupInfo 1.3.6.1.4.1.4323.2.7.2.2.7
The set of all accessible objects in the VPL group of this MIB.
Status: current Access: read-create
OBJECT-GROUP    

qbAtmPnniIfGroupInfo 1.3.6.1.4.1.4323.2.7.2.2.8
The set of all accessible objects in the PNNI interface group of this MIB.
Status: current Access: read-create
OBJECT-GROUP    

qbAtmPnniRouteAddrGroupInfo 1.3.6.1.4.1.4323.2.7.2.2.9
The set of all accessible objects in the Route group of this MIB.
Status: current Access: read-create
OBJECT-GROUP    

qbAtmInterfaceConfSigGroupInfo 1.3.6.1.4.1.4323.2.7.2.2.10
The set of all accessible objects in the Route group of this MIB.
Status: current Access: read-create
OBJECT-GROUP    

qbAtmPnniNbrPeerGroupInfo 1.3.6.1.4.1.4323.2.7.2.2.11
The set of all accessible objects in the PNNI Peer Nbr group of this MIB.
Status: current Access: read-create
OBJECT-GROUP    

qbAtmPnniPglGroupInfo 1.3.6.1.4.1.4323.2.7.2.2.12
The set of all accessible objects in the PGL group of this MIB.
Status: current Access: read-create
OBJECT-GROUP    

qbAtmPnniTimerGroupInfo 1.3.6.1.4.1.4323.2.7.2.2.13
The set of all accessible objects in the PNNI Timer group of this MIB.
Status: current Access: read-create
OBJECT-GROUP    

qbAtmPnniLinkGroupInfo 1.3.6.1.4.1.4323.2.7.2.2.14
The set of all accessible objects in the PNNI Link group of this MIB.
Status: current Access: read-create
OBJECT-GROUP    

qbAtmInBandMgtGroupInfo 1.3.6.1.4.1.4323.2.7.2.2.15
The set of all accessible objects in the in-band management group of this MIB.
Status: current Access: read-create
OBJECT-GROUP