PW-ATM-MIB

File: PW-ATM-MIB.mib (44077 bytes)

Imported modules

SNMPv2-SMI SNMPv2-CONF SNMPv2-TC
PerfHist-TC-MIB IF-MIB PW-STD-MIB
ATM-TC-MIB

Imported symbols

MODULE-IDENTITY OBJECT-TYPE Counter32
Unsigned32 mib-2 MODULE-COMPLIANCE
OBJECT-GROUP TruthValue RowStatus
RowPointer PerfCurrentCount PerfIntervalCount
InterfaceIndex pwIndex AtmVpIdentifier
AtmVcIdentifier

Defined Types

PwAtmOutboundEntry  
SEQUENCE    
  pwAtmOutboundAtmIf InterfaceIndex
  pwAtmOutboundVpi AtmVpIdentifier
  pwAtmOutboundVci AtmVcIdentifier
  pwAtmOutboundTrafficParamDescr RowPointer
  pwAtmOutboundRowStatus RowStatus

PwAtmInboundEntry  
SEQUENCE    
  pwAtmInboundAtmIf InterfaceIndex
  pwAtmInboundVpi AtmVpIdentifier
  pwAtmInboundVci AtmVcIdentifier
  pwAtmInboundTrafficParamDescr RowPointer
  pwAtmInboundRowStatus RowStatus

PwAtmCfgEntry  
SEQUENCE    
  pwAtmCfgMaxCellConcatenation Unsigned32
  pwAtmCfgFarEndMaxCellConcatenation Unsigned32
  pwAtmCfgTimeoutMode INTEGER
  pwAtmClpQosMapping TruthValue

PwAtmOutboundNto1Entry  
SEQUENCE    
  pwAtmOutboundNto1AtmIf InterfaceIndex
  pwAtmOutboundNto1Vpi AtmVpIdentifier
  pwAtmOutboundNto1Vci AtmVcIdentifier
  pwAtmOutboundNto1RowStatus RowStatus
  pwAtmOutboundNto1TrafficParamDescr RowPointer
  pwAtmOutboundNto1MappedVpi AtmVpIdentifier
  pwAtmOutboundNto1MappedVci AtmVcIdentifier

PwAtmInboundNto1Entry  
SEQUENCE    
  pwAtmInboundNto1AtmIf InterfaceIndex
  pwAtmInboundNto1Vpi AtmVpIdentifier
  pwAtmInboundNto1Vci AtmVcIdentifier
  pwAtmInboundNto1RowStatus RowStatus
  pwAtmInboundNto1TrafficParamDescr RowPointer
  pwAtmInboundNto1MappedVpi AtmVpIdentifier
  pwAtmInboundNto1MappedVci AtmVcIdentifier

PwAtmPerfCurrentEntry  
SEQUENCE    
  pwAtmPerfCurrentMissingPkts PerfCurrentCount
  pwAtmPerfCurrentPktsReOrder PerfCurrentCount
  pwAtmPerfCurrentPktsMisOrder PerfCurrentCount
  pwAtmPerfCurrentPktsTimeout PerfCurrentCount
  pwAtmPerfCurrentCellsXmit PerfCurrentCount
  pwAtmPerfCurrentCellsDropped PerfCurrentCount
  pwAtmPerfCurrentCellsReceived PerfCurrentCount
  pwAtmPerfCurrentUnknownCells PerfCurrentCount

PwAtmPerfIntervalEntry  
SEQUENCE    
  pwAtmPerfIntervalNumber Unsigned32
  pwAtmPerfIntervalValidData TruthValue
  pwAtmPerfIntervalDuration Unsigned32
  pwAtmPerfIntervalMissingPkts PerfIntervalCount
  pwAtmPerfIntervalPktsReOrder PerfIntervalCount
  pwAtmPerfIntervalPktsMisOrder PerfIntervalCount
  pwAtmPerfIntervalPktsTimeout PerfIntervalCount
  pwAtmPerfIntervalCellsXmit PerfIntervalCount
  pwAtmPerfIntervalCellsDropped PerfIntervalCount
  pwAtmPerfIntervalCellsReceived PerfIntervalCount
  pwAtmPerfIntervalUnknownCells PerfIntervalCount

PwAtmPerf1DayIntervalEntry  
SEQUENCE    
  pwAtmPerf1DayIntervalNumber Unsigned32
  pwAtmPerf1DayIntervalValidData TruthValue
  pwAtmPerf1DayIntervalDuration Unsigned32
  pwAtmPerf1DayIntervalMissingPkts Counter32
  pwAtmPerf1DayIntervalPktsReOrder Counter32
  pwAtmPerf1DayIntervalPktsMisOrder Counter32
  pwAtmPerf1DayIntervalPktsTimeout Counter32
  pwAtmPerf1DayIntervalCellsXmit Counter32
  pwAtmPerf1DayIntervalCellsDropped Counter32
  pwAtmPerf1DayIntervalCellsReceived Counter32
  pwAtmPerf1DayIntervalUnknownCells Counter32

Defined Values

pwAtmMIB 1.3.6.1.2.1.183
This MIB contains managed object definitions for pseudowire emulation of ATM over Packet Switched Networks (PSNs). This MIB supplements the PW-STD-MIB module. The PW-STD-MIB contains structures and MIB associations generic to pseudowire (PW) emulation. PW-specific MIBs (such as this) contain config and stats for specific PW types. Copyright (c) 2009 IETF Trust and the persons identified as authors of the code. All rights reserved. Redistribution and use in source and binary forms, with or without modification, are permitted provided that the following conditions are met: - Redistributions of source code must retain the above copyright notice, this list of conditions and the following disclaimer. - Redistributions in binary form must reproduce the above copyright notice, this list of conditions and the following disclaimer in the documentation and/or other materials provided with the distribution. - Neither the name of Internet Society, IETF or IETF Trust, nor the names of specific contributors, may be used to endorse or promote products derived from this software without specific prior written permission. THIS SOFTWARE IS PROVIDED BY THE COPYRIGHT HOLDERS AND CONTRIBUTORS 'AS IS' AND ANY EXPRESS OR IMPLIED WARRANTIES, INCLUDING, BUT NOT LIMITED TO, THE IMPLIED WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE ARE DISCLAIMED. IN NO EVENT SHALL THE COPYRIGHT OWNER OR CONTRIBUTORS BE LIABLE FOR ANY DIRECT, INDIRECT, INCIDENTAL, SPECIAL, EXEMPLARY, OR CONSEQUENTIAL DAMAGES (INCLUDING, BUT NOT LIMITED TO, PROCUREMENT OF SUBSTITUTE GOODS OR SERVICES; LOSS OF USE, DATA, OR PROFITS; OR BUSINESS INTERRUPTION) HOWEVER CAUSED AND ON ANY THEORY OF LIABILITY, WHETHER IN CONTRACT, STRICT LIABILITY, OR TORT (INCLUDING NEGLIGENCE OR OTHERWISE) ARISING IN ANY WAY OUT OF THE USE OF THIS SOFTWARE, EVEN IF ADVISED OF THE POSSIBILITY OF SUCH DAMAGE. This version of this MIB module is part of RFC 5605; see the RFC itself for full legal notices.
MODULE-IDENTITY    

pwAtmNotifications 1.3.6.1.2.1.183.0
OBJECT IDENTIFIER    

pwAtmObjects 1.3.6.1.2.1.183.1
OBJECT IDENTIFIER    

pwAtmConformance 1.3.6.1.2.1.183.2
OBJECT IDENTIFIER    

pwAtmOutboundTable 1.3.6.1.2.1.183.1.1
This table specifies the information for an ATM PW to be carried over the PSN in the outbound direction. An entry is created in this table for every entry in the pwTable with a pwType equal to one of the following: atmAal5SduVcc(2), atmCell1to1Vcc(12), atmCell1to1Vpc(13) or atmAal5PduVcc(14), or atmTransparent(3).
Status: current Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    PwAtmOutboundEntry

pwAtmOutboundEntry 1.3.6.1.2.1.183.1.1.1
A row in this table represents an ATM PW that needs to be adapted and carried over the PSN. This table is indexed by pwIndex from pwTable. Unless otherwise specified, all writeable objects in this table MUST NOT be changed after row activation in the generic pwTable, and values must persist after reboot.
Status: current Access: not-accessible
OBJECT-TYPE    
  PwAtmOutboundEntry  

pwAtmOutboundAtmIf 1.3.6.1.2.1.183.1.1.1.1
The ATM Interface that receives cells from the ATM network.
Status: current Access: read-create
OBJECT-TYPE    
  InterfaceIndex  

pwAtmOutboundVpi 1.3.6.1.2.1.183.1.1.1.2
VPI value of this ATM PW. The value may indicate the translated value when egress generates new VPI.
Status: current Access: read-create
OBJECT-TYPE    
  AtmVpIdentifier  

pwAtmOutboundVci 1.3.6.1.2.1.183.1.1.1.3
VCI value of this ATM PW. The value may indicate the translated value when egress generates new VCI.
Status: current Access: read-create
OBJECT-TYPE    
  AtmVcIdentifier  

pwAtmOutboundTrafficParamDescr 1.3.6.1.2.1.183.1.1.1.4
This object represents a pointer to an ATM traffic-parameter-specific row in either a private or standard table that will be employed while receiving cells from the ATM network. This row should contain a set of self-consistent ATM traffic parameters including the ATM traffic service category. A value of 0.0 indicates Best Effort.
Status: current Access: read-create
OBJECT-TYPE    
  RowPointer  

pwAtmOutboundRowStatus 1.3.6.1.2.1.183.1.1.1.5
This object is used to create, modify, or delete a row in this table. Unless otherwise specified, all writeable objects in this table MUST NOT be changed after row activation as explained in the pwAtmOutboundEntry.
Status: current Access: read-create
OBJECT-TYPE    
  RowStatus  

pwAtmInboundTable 1.3.6.1.2.1.183.1.3
This table specifies the information for an ATM PW in the inbound direction.
Status: current Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    PwAtmInboundEntry

pwAtmInboundEntry 1.3.6.1.2.1.183.1.3.1
A row in this table represents an ATM PW that needs to be sent into the ATM network after reconstructing cells from packets received from a PSN. This table is indexed by pwIndex from pwTable. An entry is created in this table for every entry in the pwTable with a pwType equal to one of the following: atmAal5SduVcc(2), atmCell1to1Vcc(12), atmCell1to1Vpc(13), atmAal5PduVcc(14), or atmTransparent(3). Unless otherwise specified, all writeable objects in this table MUST NOT be changed after row activation in the generic pwTable, and values must persist after reboot.
Status: current Access: not-accessible
OBJECT-TYPE    
  PwAtmInboundEntry  

pwAtmInboundAtmIf 1.3.6.1.2.1.183.1.3.1.1
The ATM Interface that sends cells into the ATM network after reconstructing cells from packets received from a PSN.
Status: current Access: read-create
OBJECT-TYPE    
  InterfaceIndex  

pwAtmInboundVpi 1.3.6.1.2.1.183.1.3.1.2
VPI value of this ATM PW. If the pwType is atmTransparent, then the value will be set to zero.
Status: current Access: read-create
OBJECT-TYPE    
  AtmVpIdentifier  

pwAtmInboundVci 1.3.6.1.2.1.183.1.3.1.3
VCI value of this ATM PW. If the pwType is atmTransparent, atmCell1to1Vpc, or atmCellNto1Vpc, then the value will be set to zero.
Status: current Access: read-create
OBJECT-TYPE    
  AtmVcIdentifier  

pwAtmInboundTrafficParamDescr 1.3.6.1.2.1.183.1.3.1.4
This object represents a pointer to an ATM traffic-parameter- specific row in either a private or standard table that will be employed while transmitting into the ATM network. This table contains a set of self-consistent ATM traffic parameters including the ATM traffic service category. A value of 0.0 indicates Best Effort.
Status: current Access: read-create
OBJECT-TYPE    
  RowPointer  

pwAtmInboundRowStatus 1.3.6.1.2.1.183.1.3.1.5
This object is used to create, modify, or delete a row in this table. Unless otherwise specified, all writeable objects in this table MUST NOT be changed after row activation as explained in the pwAtmInboundEntry.
Status: current Access: read-create
OBJECT-TYPE    
  RowStatus  

pwAtmCfgTable 1.3.6.1.2.1.183.1.5
This table specifies generic information for an ATM PW to be carried over PSN in any mode.
Status: current Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    PwAtmCfgEntry

pwAtmCfgEntry 1.3.6.1.2.1.183.1.5.1
This table contains a set of parameters for the ATM PW that needs to be adapted and carried over the PSN. This table is indexed by pwIndex from pwTable. An entry is created for every new ATM type associated pwIndex in the pwTable. Unless otherwise specified, all read-write objects in this table MAY be changed when the PW is defined as not active, and all RW objects values must persist after reboot.
Status: current Access: not-accessible
OBJECT-TYPE    
  PwAtmCfgEntry  

pwAtmCfgMaxCellConcatenation 1.3.6.1.2.1.183.1.5.1.1
The maximum number of ATM cells that can be concatenated into one PW packet towards the PSN. In a non-LDP or other signaling protocol environment, this object MAY be changed at anytime, but traffic might be interrupted; otherwise, it may be changed when PW is not active.
Status: current Access: read-write
OBJECT-TYPE    
  Unsigned32 1..29  

pwAtmCfgFarEndMaxCellConcatenation 1.3.6.1.2.1.183.1.5.1.2
The maximum number of ATM cells that can be concatenated into one PW packet towards PSN as reported by the far end. If there is no LDP in use, the object will either return a value of 0 or allow setting it for calculating protocol overhead.
Status: current Access: read-write
OBJECT-TYPE    
  Unsigned32 1..29  

pwAtmCfgTimeoutMode 1.3.6.1.2.1.183.1.5.1.3
This object determines whether or not a packet can be transmitted to the PSN based on timeout expiration for collecting cells. The actual handling of the timeout is implementation-specific; as such, this object may be changed at any time under proper consideration of the traffic interruption effect.
Status: current Access: read-write
OBJECT-TYPE    
  INTEGER notApplicable(1), disabled(2), enabled(3)  

pwAtmClpQosMapping 1.3.6.1.2.1.183.1.5.1.4
This object indicates whether the Cell Loss Priority (CLP) bits should be considered when setting the value in the Quality-of-Service fields of the encapsulating protocol (e.g., EXP fields of the MPLS Label Stack). Selecting True allows the drop precedence to be preserved across the PSN. In transparent cell transport, the value of this object MUST be false(2); in other cases, it can be changed at any time.
Status: current Access: read-write
OBJECT-TYPE    
  TruthValue  

pwAtmOutboundNto1Table 1.3.6.1.2.1.183.1.6
This table specifies the information for an ATM PW to be carried over the PSN in the outbound direction. Up to N entries can be created in this table for every entry in the pwTable with a pwType equal to: atmCellNto1Vcc(9) or atmCellNto1Vpc(10). An entry can be created only when the VP/VC are known. A single entry will be created in this table for every entry in the pwTable with a pwType equal to one of the following: atmCell1to1Vcc(12), atmCell1to1Vpc(13), atmAal5PduVcc(14), atmAal5SduVcc(2), or atmTransparent(3).
Status: current Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    PwAtmOutboundNto1Entry

pwAtmOutboundNto1Entry 1.3.6.1.2.1.183.1.6.1
A row in this table represents an ATM PW that needs to be adapted and carried over PSN. This table is indexed by pwIndex from pwTable and the ATM interface with VPL/VCLs. In atmTransparent(3), Vpi and VCi will be 0xFFFF during set operation. Unless otherwise specified, all read-create objects in this table MUST NOT be changed after row activation and SHOULD remain unchanged after reboot.
Status: current Access: not-accessible
OBJECT-TYPE    
  PwAtmOutboundNto1Entry  

pwAtmOutboundNto1AtmIf 1.3.6.1.2.1.183.1.6.1.1
The ATM Interface that receives cells from the ATM network.
Status: current Access: not-accessible
OBJECT-TYPE    
  InterfaceIndex  

pwAtmOutboundNto1Vpi 1.3.6.1.2.1.183.1.6.1.2
VPI value of this ATM PW. In atmTransparent(3), Vpi will be the equivalent of 0xFFFF.
Status: current Access: not-accessible
OBJECT-TYPE    
  AtmVpIdentifier  

pwAtmOutboundNto1Vci 1.3.6.1.2.1.183.1.6.1.3
VCI value of this ATM PW. In atmTransparent(3), or the VP case, the value will be the equivalent of 0xFFFF.
Status: current Access: not-accessible
OBJECT-TYPE    
  AtmVcIdentifier  

pwAtmOutboundNto1RowStatus 1.3.6.1.2.1.183.1.6.1.4
This object is used to create, modify or delete a row in this table.
Status: current Access: read-create
OBJECT-TYPE    
  RowStatus  

pwAtmOutboundNto1TrafficParamDescr 1.3.6.1.2.1.183.1.6.1.5
This object represents a pointer to an ATM traffic-parameter- specific row in either private or standard table that will be employed while receiving cells from the ATM network. This table should contain a set of self-consistent ATM traffic parameters including the ATM traffic service category. A value of 0.0 indicates Best Effort.
Status: current Access: read-create
OBJECT-TYPE    
  RowPointer  

pwAtmOutboundNto1MappedVpi 1.3.6.1.2.1.183.1.6.1.6
The egress-generated VPI value of this ATM PW. The entry is valid for PW type of atmCellNto1Vcc(9), atmCellNto1Vpc(10), atmCell1to1Vcc(12), or atmCell1to1Vpc(13). In other types, the value will be the equivalent of 0xFFFF. Value MAY be changed when the PW is defined as not active.
Status: current Access: read-create
OBJECT-TYPE    
  AtmVpIdentifier  

pwAtmOutboundNto1MappedVci 1.3.6.1.2.1.183.1.6.1.7
The egress-generated VCI value of this ATM PW. The entry is valid for PW type of atmCellNto1Vcc(9), atmCellNto1Vpc(10), atmCell1to1Vcc(12), or atmCell1to1Vpc(13. In the VP case or other types, the value will be the equivalent of 0xFFFF. Value MAY be changed when the PW is defined as not active.
Status: current Access: read-create
OBJECT-TYPE    
  AtmVcIdentifier  

pwAtmInboundNto1Table 1.3.6.1.2.1.183.1.7
This table specifies the information for an ATM PW to be carried over PSN in the Inbound direction. Up to N entries can be created in this table for every entry in the pwTable with a pwType equal to: atmCellNto1Vcc(9) or atmCellNto1Vpc(10). An entry can be created only when the VP/VC are known. A single entry will be created in this table for every entry in the pwTable with a pwType equal to one of the following: atmCell1to1Vcc(12), atmCell1to1Vpc(13), atmAal5PduVcc(14), atmAal5SduVcc(2), or atmTransparent(3).
Status: current Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    PwAtmInboundNto1Entry

pwAtmInboundNto1Entry 1.3.6.1.2.1.183.1.7.1
A row in this table represents an ATM PW that needs to be adapted and carried over PSN. This table is indexed by pwIndex from pwTable and the ATM interface with VPL/VCLs. In atmTransparent(3), Vpi and VCi will be 0xFFFF during set operation. Unless otherwise specified, all Read-Create objects in this table MUST NOT be changed after row activation and SHOULD remain unchanged after reboot.
Status: current Access: not-accessible
OBJECT-TYPE    
  PwAtmInboundNto1Entry  

pwAtmInboundNto1AtmIf 1.3.6.1.2.1.183.1.7.1.1
The ATM Interface that receives cells from the ATM network.
Status: current Access: not-accessible
OBJECT-TYPE    
  InterfaceIndex  

pwAtmInboundNto1Vpi 1.3.6.1.2.1.183.1.7.1.2
VPI value of this ATM PW. In atmTransparent(3), Vpi will be the equivalent of 0xFFFF.
Status: current Access: not-accessible
OBJECT-TYPE    
  AtmVpIdentifier  

pwAtmInboundNto1Vci 1.3.6.1.2.1.183.1.7.1.3
VCI value of this ATM PW. In atmTransparent(3), or the VP case, the value will be the equivalent of 0xFFFF.
Status: current Access: not-accessible
OBJECT-TYPE    
  AtmVcIdentifier  

pwAtmInboundNto1RowStatus 1.3.6.1.2.1.183.1.7.1.4
This object is used to create, modify, or delete a row in this table.
Status: current Access: read-create
OBJECT-TYPE    
  RowStatus  

pwAtmInboundNto1TrafficParamDescr 1.3.6.1.2.1.183.1.7.1.5
This object represents a pointer to an ATM traffic-parameter- specific row in either a private or standard table that will be employed while receiving cells from the ATM network. This table should contain a set of self-consistent ATM traffic parameters including the ATM traffic service category. A value of 0.0 indicates Best Effort.
Status: current Access: read-create
OBJECT-TYPE    
  RowPointer  

pwAtmInboundNto1MappedVpi 1.3.6.1.2.1.183.1.7.1.6
The generated VPI value of this ATM PW. The entry is valid for PW type of atmCellNto1Vcc(9), atmCellNto1Vpc(10), atmCell1to1Vcc(12), or atmCell1to1Vpc(13). In other types, the value will be the equivalent of 0xFFFF. Value MAY be changed when the PW is defined as not active.
Status: current Access: read-create
OBJECT-TYPE    
  AtmVpIdentifier  

pwAtmInboundNto1MappedVci 1.3.6.1.2.1.183.1.7.1.7
The generated VCI value of this ATM PW. The entry is valid for PW type of atmCellNto1Vcc(9), atmCellNto1Vpc(10), atmCell1to1Vcc(12), or atmCell1to1Vpc(13. In the VP case or other types, the value will be the equivalent of 0xFFFF. Value MAY be changed when the PW is defined as not active.
Status: current Access: read-create
OBJECT-TYPE    
  AtmVcIdentifier  

pwAtmPerfCurrentTable 1.3.6.1.2.1.183.1.8
The current 15-minute interval counts are in this table. This table provides performance information per ATM PW.
Status: current Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    PwAtmPerfCurrentEntry

pwAtmPerfCurrentEntry 1.3.6.1.2.1.183.1.8.1
An entry in this table is created by the agent for every pwAtmCfgTable entry. After 15 minutes, the contents of this table entry are copied to a new entry in the pwAtmPerfInterval table and the counts in this entry are reset to zero.
Status: current Access: not-accessible
OBJECT-TYPE    
  PwAtmPerfCurrentEntry  

pwAtmPerfCurrentMissingPkts 1.3.6.1.2.1.183.1.8.1.1
Number of missing packets (as detected via control word sequence number gaps).
Status: current Access: read-only
OBJECT-TYPE    
  PerfCurrentCount  

pwAtmPerfCurrentPktsReOrder 1.3.6.1.2.1.183.1.8.1.2
Number of packets detected out of sequence (via control word sequence number), but successfully re-ordered. Note: some implementations may not support this feature.
Status: current Access: read-only
OBJECT-TYPE    
  PerfCurrentCount  

pwAtmPerfCurrentPktsMisOrder 1.3.6.1.2.1.183.1.8.1.3
Number of packets detected out of order (via control word sequence numbers).
Status: current Access: read-only
OBJECT-TYPE    
  PerfCurrentCount  

pwAtmPerfCurrentPktsTimeout 1.3.6.1.2.1.183.1.8.1.4
Number of packets transmitted due to timeout expiration while attempting to collect cells.
Status: current Access: read-only
OBJECT-TYPE    
  PerfCurrentCount  

pwAtmPerfCurrentCellsXmit 1.3.6.1.2.1.183.1.8.1.5
Number of transmitted cells.
Status: current Access: read-only
OBJECT-TYPE    
  PerfCurrentCount  

pwAtmPerfCurrentCellsDropped 1.3.6.1.2.1.183.1.8.1.6
Number of dropped cells.
Status: current Access: read-only
OBJECT-TYPE    
  PerfCurrentCount  

pwAtmPerfCurrentCellsReceived 1.3.6.1.2.1.183.1.8.1.7
Number of received cells.
Status: current Access: read-only
OBJECT-TYPE    
  PerfCurrentCount  

pwAtmPerfCurrentUnknownCells 1.3.6.1.2.1.183.1.8.1.8
Number of cells received from the PSN with unknown VPI or VCI values. This object is relevant only in N:1 mode.
Status: current Access: read-only
OBJECT-TYPE    
  PerfCurrentCount  

pwAtmPerfIntervalTable 1.3.6.1.2.1.183.1.9
This table provides performance information per ATM PW similar to the pwAtmPerfCurrentTable above. However, these counts represent historical 15 minute intervals. Typically, this table will have a maximum of 96 entries for a 24 hour period.
Status: current Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    PwAtmPerfIntervalEntry

pwAtmPerfIntervalEntry 1.3.6.1.2.1.183.1.9.1
An entry in this table is created by the agent for every pwAtmPerfCurrentEntry that is 15 minutes old. The contents of the Current entry are copied to the new entry here. The Current entry then resets its counts to zero for the next current 15 minute interval.
Status: current Access: not-accessible
OBJECT-TYPE    
  PwAtmPerfIntervalEntry  

pwAtmPerfIntervalNumber 1.3.6.1.2.1.183.1.9.1.1
A number (normally between 1 and 96 to cover a 24 hour period) that identifies the interval for which the set of statistics is available. The interval identified by 1 is the most recently completed 15 minute interval, and the interval identified by N is the interval immediately preceding the one identified by N-1. The minimum range of N is 1 through 4. The default range is 1 through 32. The maximum value of N is 96.
Status: current Access: not-accessible
OBJECT-TYPE    
  Unsigned32 1..96  

pwAtmPerfIntervalValidData 1.3.6.1.2.1.183.1.9.1.2
This variable indicates if the data for this interval is valid.
Status: current Access: read-only
OBJECT-TYPE    
  TruthValue  

pwAtmPerfIntervalDuration 1.3.6.1.2.1.183.1.9.1.3
The duration of a particular interval in seconds. Adjustments in the system's time-of-day clock, may cause the interval to be greater or less than the normal value. Therefore, this actual interval value is provided.
Status: current Access: read-only
OBJECT-TYPE    
  Unsigned32  

pwAtmPerfIntervalMissingPkts 1.3.6.1.2.1.183.1.9.1.4
Number of missing packets (as detected via control word sequence number gaps).
Status: current Access: read-only
OBJECT-TYPE    
  PerfIntervalCount  

pwAtmPerfIntervalPktsReOrder 1.3.6.1.2.1.183.1.9.1.5
Number of packets detected out of sequence (via control word sequence number), but successfully re-ordered. Note: some implementations may not support this feature.
Status: current Access: read-only
OBJECT-TYPE    
  PerfIntervalCount  

pwAtmPerfIntervalPktsMisOrder 1.3.6.1.2.1.183.1.9.1.6
Number of packets detected out of order (via control word sequence numbers).
Status: current Access: read-only
OBJECT-TYPE    
  PerfIntervalCount  

pwAtmPerfIntervalPktsTimeout 1.3.6.1.2.1.183.1.9.1.7
Number of packets transmitted due to timeout expiration.
Status: current Access: read-only
OBJECT-TYPE    
  PerfIntervalCount  

pwAtmPerfIntervalCellsXmit 1.3.6.1.2.1.183.1.9.1.8
Number of transmitted cells.
Status: current Access: read-only
OBJECT-TYPE    
  PerfIntervalCount  

pwAtmPerfIntervalCellsDropped 1.3.6.1.2.1.183.1.9.1.9
Number of dropped cells.
Status: current Access: read-only
OBJECT-TYPE    
  PerfIntervalCount  

pwAtmPerfIntervalCellsReceived 1.3.6.1.2.1.183.1.9.1.10
Number of received cells.
Status: current Access: read-only
OBJECT-TYPE    
  PerfIntervalCount  

pwAtmPerfIntervalUnknownCells 1.3.6.1.2.1.183.1.9.1.11
Number of cells received from the PSN with unknown VPI or VCI values. This object is relevant only in N:1 mode.
Status: current Access: read-only
OBJECT-TYPE    
  PerfIntervalCount  

pwAtmPerf1DayIntervalTable 1.3.6.1.2.1.183.1.10
This table provides performance information per ATM PW similar to the pwAtmPerfIntervalTable above. However, these counters represent historical one-day intervals up to one full month.
Status: current Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    PwAtmPerf1DayIntervalEntry

pwAtmPerf1DayIntervalEntry 1.3.6.1.2.1.183.1.10.1
An entry is created in this table by the agent for every entry in the pwAtmCfgTable table.
Status: current Access: not-accessible
OBJECT-TYPE    
  PwAtmPerf1DayIntervalEntry  

pwAtmPerf1DayIntervalNumber 1.3.6.1.2.1.183.1.10.1.1
The number of intervals, where 1 indicates current day measured period and 2 and above indicate previous days, respectively.
Status: current Access: not-accessible
OBJECT-TYPE    
  Unsigned32 1..365  

pwAtmPerf1DayIntervalValidData 1.3.6.1.2.1.183.1.10.1.2
This object indicates if the data for this interval is valid.
Status: current Access: read-only
OBJECT-TYPE    
  TruthValue  

pwAtmPerf1DayIntervalDuration 1.3.6.1.2.1.183.1.10.1.3
The duration of a particular interval in seconds. Adjustments in the system's time-of-day clock may cause the interval to be greater or less than the normal value. Therefore, this actual interval value is provided.
Status: current Access: read-only
OBJECT-TYPE    
  Unsigned32  

pwAtmPerf1DayIntervalMissingPkts 1.3.6.1.2.1.183.1.10.1.4
Number of missing packets (as detected via control word sequence number gaps).
Status: current Access: read-only
OBJECT-TYPE    
  Counter32  

pwAtmPerf1DayIntervalPktsReOrder 1.3.6.1.2.1.183.1.10.1.5
Number of packets detected out of sequence (via control word sequence number), but successfully re-ordered. Note: some implementations may not support this feature.
Status: current Access: read-only
OBJECT-TYPE    
  Counter32  

pwAtmPerf1DayIntervalPktsMisOrder 1.3.6.1.2.1.183.1.10.1.6
Number of packets detected out of order (via control word sequence numbers) and that could not be re-ordered.
Status: current Access: read-only
OBJECT-TYPE    
  Counter32  

pwAtmPerf1DayIntervalPktsTimeout 1.3.6.1.2.1.183.1.10.1.7
Number of packets transmitted due to timeout expiration.
Status: current Access: read-only
OBJECT-TYPE    
  Counter32  

pwAtmPerf1DayIntervalCellsXmit 1.3.6.1.2.1.183.1.10.1.8
Number of transmitted cells.
Status: current Access: read-only
OBJECT-TYPE    
  Counter32  

pwAtmPerf1DayIntervalCellsDropped 1.3.6.1.2.1.183.1.10.1.9
Number of dropped cells.
Status: current Access: read-only
OBJECT-TYPE    
  Counter32  

pwAtmPerf1DayIntervalCellsReceived 1.3.6.1.2.1.183.1.10.1.10
Number of received cells.
Status: current Access: read-only
OBJECT-TYPE    
  Counter32  

pwAtmPerf1DayIntervalUnknownCells 1.3.6.1.2.1.183.1.10.1.11
Number of cells received from the PSN with unknown VPI or VCI values. This object is relevant only in N:1 mode.
Status: current Access: read-only
OBJECT-TYPE    
  Counter32  

pwAtmCompliances 1.3.6.1.2.1.183.2.1
OBJECT IDENTIFIER    

pwAtmGroups 1.3.6.1.2.1.183.2.2
OBJECT IDENTIFIER    

pwAtmCompliance 1.3.6.1.2.1.183.2.1.2
The compliance statement for agents that support ATM PW.
Status: current Access: read-only
MODULE-COMPLIANCE    

pwAtmCfgGroup 1.3.6.1.2.1.183.2.2.5
Collection of objects for basic ATM PW configuration.
Status: current Access: read-only
OBJECT-GROUP    

pwAtmPerfGroup 1.3.6.1.2.1.183.2.2.6
Collection of objects for basic ATM PW Performance.
Status: current Access: read-only
OBJECT-GROUP    

pwAtmOutbound1to1Group 1.3.6.1.2.1.183.2.2.7
Collection of objects for basic 1:1 ATM PW outbound configuration.
Status: current Access: read-only
OBJECT-GROUP    

pwAtmInbound1to1Group 1.3.6.1.2.1.183.2.2.8
Collection of objects for basic 1:1 ATM PW inbound configuration.
Status: current Access: read-only
OBJECT-GROUP    

pwAtmOutboundNto1Group 1.3.6.1.2.1.183.2.2.9
Collection of objects for N:1, 1:1, or transparent ATM PW outbound configuration.
Status: current Access: read-only
OBJECT-GROUP    

pwAtmInboundNto1Group 1.3.6.1.2.1.183.2.2.10
Collection of objects for N:1, 1:1, or transparent ATM PW inbound configuration.
Status: current Access: read-only
OBJECT-GROUP