PRVT-RING-EPS-MIB

File: PRVT-RING-EPS-MIB.mib (46962 bytes)

Imported modules

SNMPv2-SMI	SNMPv2-TC	SNMPv2-CONF
IF-MIB	Q-BRIDGE-MIB	IEEE8021-CFM-MIB
PRVT-SWITCH-MIB

Imported symbols

MODULE-IDENTITY	OBJECT-TYPE	Unsigned32
NOTIFICATION-TYPE	TEXTUAL-CONVENTION	RowStatus
MacAddress	TruthValue	DisplayString
MODULE-COMPLIANCE	OBJECT-GROUP	NOTIFICATION-GROUP
InterfaceIndexOrZero	VlanIdOrNone	Dot1agCfmMDLevelOrNone
Dot1agCfmMepIdOrZero	switch

Defined Types

PrvtRingEpsModeType
Version of the protocol the instance will use
TEXTUAL-CONVENTION
	INTEGER	rapsMode8032v1(1), rapsMode8032v2(2)

PrvtRingEpsStateType
State of the R-APS request processing logic
TEXTUAL-CONVENTION
	INTEGER	rapsInit(0), rapsIdle(1), rapsProtection(2), rapsManualSwitch(3), rapsForcedSwitch(4), rapsPending(5)

PrvtRingEpsLocalCommandType
Local system state given by the top priority command received
TEXTUAL-CONVENTION
	INTEGER	rapsLcNoRequest(0), rapsLcExercise(1), rapsLcManualSwitch(2), rapsLcSignalDegrade(3), rapsLcSignalFail(4), rapsLcForcedSwitch(5), rapsLcClear(6), rapsLcLockoutOfProtection(7)

PrvtRingEpsRemoteRequestType
Remote command received via RAPS packets
TEXTUAL-CONVENTION
	INTEGER	rapsRsNone(-1), rapsRsNoRequest(0), rapsRsManualSwitch(7), rapsRsSignalFail(11), rapsRsForcedSwitch(13), rapsRsEvent(14)

PrvtRingEpsNodeRoleType
Role of the defined node inside the protected ring
TEXTUAL-CONVENTION
	INTEGER	rapsNrSimpleNode(0), rapsNrRplNeighborNode(1), rapsNrRplOwner(2)

PrvtRingEpsRplPortType
Ring port designated as RPL (only valid if prvtRingEpsNodeRole is rapsNrRplOwner or rapsNrRplNeighborNode
TEXTUAL-CONVENTION
	INTEGER	port0(0), port1(1), none(2)

PrvtRingEpsDefectType
Ring port designated as RPL (only valid if prvtRingEpsNodeRole is rapsNrRplOwner or rapsNrRplNeighborNode
TEXTUAL-CONVENTION
	BITS	rapsDprovisioningMismatch(0)

PrvtRingEpsPortStatusType
Status of the port link
TEXTUAL-CONVENTION
	INTEGER	rapsPsOk(0), rapsPsBlocked(1), rapsPsFailed(2)

PrvtRingEpsPeerStatusType
Status bits set in the received RAPS packet. The meanings are: bRplBlocked(0) The RPL link is blocked by the RPL owner. bDoNotFlush(1) RAPS sender requests that we do don flush our FDB. bBlockedPortReference(2) The port that is blocked by the sender of the RAPS packet.
TEXTUAL-CONVENTION
	BITS	bRplBlocked(0), bDoNotFlush(1), bBlockedPortReference(2)

PrvtRingEpsInstanceEntry
SEQUENCE
	prvtRingEpsInstanceIndex	Unsigned32
	prvtRingEpsMode	PrvtRingEpsModeType
	prvtRingEpsNodeRole	PrvtRingEpsNodeRoleType
	prvtRingEpsState	PrvtRingEpsStateType
	prvtRingEpsLocalCommand	PrvtRingEpsLocalCommandType
	prvtRingEpsControlVlan	VlanIdOrNone
	prvtRingEpsPort0Ifindex	InterfaceIndexOrZero
	prvtRingEpsPort1Ifindex	InterfaceIndexOrZero
	prvtRingEpsRplPort	PrvtRingEpsRplPortType
	prvtRingEpsManualSwitchPort	PrvtRingEpsRplPortType
	prvtRingEpsCfmMdLevel	Dot1agCfmMDLevelOrNone
	prvtRingEpsPort0Mep	Dot1agCfmMepIdOrZero
	prvtRingEpsPort1Mep	Dot1agCfmMepIdOrZero
	prvtRingEpsRevertive	TruthValue
	prvtRingEpsNoVirtualChannel	TruthValue
	prvtRingEpsHoldOffTimer	Unsigned32
	prvtRingEpsWaitToRestoreTimer	Unsigned32
	prvtRingEpsGuardTimer	Unsigned32
	prvtRingEpsWaitToBlockTimer	Unsigned32
	prvtRingEpsDefectFop	PrvtRingEpsDefectType
	prvtRingEpsPort0Status	PrvtRingEpsPortStatusType
	prvtRingEpsPort1Status	PrvtRingEpsPortStatusType
	prvtRingEpsPort0PeerNodeId	MacAddress
	prvtRingEpsPort1PeerNodeId	MacAddress
	prvtRingEpsPort0PeerCommand	PrvtRingEpsRemoteRequestType
	prvtRingEpsPort1PeerCommand	PrvtRingEpsRemoteRequestType
	prvtRingEpsPort0PeerStatus	PrvtRingEpsPeerStatusType
	prvtRingEpsPort1PeerStatus	PrvtRingEpsPeerStatusType
	prvtRingEpsOperationalStatus	TruthValue
	prvtRingEpsAdminStatus	TruthValue
	prvtRingEpsRowStatus	RowStatus
	prvtRingEpsForcedSwitchPort	PrvtRingEpsRplPortType
	prvtRingEpsInstanceDescription	DisplayString
	prvtRingEpsRingId	Unsigned32
	prvtRingEpsPort0MonitoringMethod	INTEGER
	prvtRingEpsPort1MonitoringMethod	INTEGER

PrvtRingEpsVlanEntry
SEQUENCE
	prvtRingEpsVlanIndex	Unsigned32
	prvtRingEpsInstance	Unsigned32
	prvtRingEpsVlanRowStatus	RowStatus

PrvtRingEpsSubRingEntry
SEQUENCE
	prvtRingEpsSubRingIndex	Unsigned32
	prvtRingEpsSubRingNodeRole	PrvtRingEpsNodeRoleType
	prvtRingEpsSubRingState	PrvtRingEpsStateType
	prvtRingEpsSubRingLocalCommand	PrvtRingEpsLocalCommandType
	prvtRingEpsSubRingPortIfindex	InterfaceIndexOrZero
	prvtRingEpsSubRingPortMep	Dot1agCfmMepIdOrZero
	prvtRingEpsSubRingRplPort	PrvtRingEpsRplPortType
	prvtRingEpsSubRingVirtualChannelVlan	VlanIdOrNone
	prvtRingEpsSubRingRevertive	TruthValue
	prvtRingEpsSubRingHoldOffTimer	Unsigned32
	prvtRingEpsSubRingWaitToRestoreTimer	Unsigned32
	prvtRingEpsSubRingGuardTimer	Unsigned32
	prvtRingEpsSubRingWaitToBlockTimer	Unsigned32
	prvtRingEpsSubRingDefectFop	PrvtRingEpsDefectType
	prvtRingEpsSubRingPortStatus	PrvtRingEpsPortStatusType
	prvtRingEpsSubRingPortPeerNodeId	MacAddress
	prvtRingEpsSubRingPeerCommand	PrvtRingEpsRemoteRequestType
	prvtRingEpsSubRingPeerStatus	PrvtRingEpsPeerStatusType
	prvtRingEpsSubRingVcPeerNodeId	MacAddress
	prvtRingEpsSubRingVcPeerCommand	PrvtRingEpsRemoteRequestType
	prvtRingEpsSubRingVcPeerStatus	PrvtRingEpsPeerStatusType
	prvtRingEpsSubRingPropagateTC	TruthValue
	prvtRingEpsSubRingOperationalStatus	TruthValue
	prvtRingEpsSubRingAdminStatus	TruthValue
	prvtRingEpsSubRingRowStatus	RowStatus
	prvtRingEpsSubRingControlVlan	VlanIdOrNone
	prvtRingEpsSubRingDescription	DisplayString
	prvtRingEpsSubRingRingId	Unsigned32
	prvtRingEpsSubRingMonitoringMethod	INTEGER

Defined Values

prvtRingEpsMib		1.3.6.1.4.1.738.1.5.134
This private MIB provides capability of controlling the automatic Ring Ethernet Protection Switching (ITU-T G.8032)
MODULE-IDENTITY

prvtRingEpsNotifications		1.3.6.1.4.1.738.1.5.134.0
OBJECT IDENTIFIER

prvtRingEpsObjects		1.3.6.1.4.1.738.1.5.134.1
OBJECT IDENTIFIER

prvtRingEpsConformance		1.3.6.1.4.1.738.1.5.134.2
OBJECT IDENTIFIER

prvtRingEpsInstances		1.3.6.1.4.1.738.1.5.134.1.1
OBJECT IDENTIFIER

prvtRingEpsVlans		1.3.6.1.4.1.738.1.5.134.1.2
OBJECT IDENTIFIER

prvtRingEpsSubRings		1.3.6.1.4.1.738.1.5.134.1.3
OBJECT IDENTIFIER

prvtRingEpsInstanceTable		1.3.6.1.4.1.738.1.5.134.1.1.1
This table includes information about the ring instances defined on this node.
Status: current	Access: not-accessible
OBJECT-TYPE
	SEQUENCE OF
		PrvtRingEpsInstanceEntry

prvtRingEpsInstanceEntry		1.3.6.1.4.1.738.1.5.134.1.1.1.1
NONE
Status: current	Access: not-accessible
OBJECT-TYPE
	PrvtRingEpsInstanceEntry

prvtRingEpsInstanceIndex		1.3.6.1.4.1.738.1.5.134.1.1.1.1.1
RAPS instance index
Status: current	Access: not-accessible
OBJECT-TYPE
	Unsigned32	1..10

prvtRingEpsMode		1.3.6.1.4.1.738.1.5.134.1.1.1.1.2
Version of the protocol the instance will use
Status: current	Access: read-create
OBJECT-TYPE
	PrvtRingEpsModeType

prvtRingEpsNodeRole		1.3.6.1.4.1.738.1.5.134.1.1.1.1.3
This variable identifies the role that the node will play inside the ring. The node can have two special roles, RPL owner or RPL neighbor, when one of its ports is designated as RPL. The ring can have a single RPL owner and a single RPL neighbor, connected between eachother via the RPL. If neither of the node ports are designated as RPL, then the node should have the role of a Simple node
Status: current	Access: read-create
OBJECT-TYPE
	PrvtRingEpsNodeRoleType

prvtRingEpsState		1.3.6.1.4.1.738.1.5.134.1.1.1.1.4
This variable identifies the state of the ring node according to the standard state machine.
Status: current	Access: read-only
OBJECT-TYPE
	PrvtRingEpsStateType

prvtRingEpsLocalCommand		1.3.6.1.4.1.738.1.5.134.1.1.1.1.5
The user can control the ring using a set of commands allowing blocking and unblocking of ports. These commands are rapsLcManualSwitch, rapsLcForcedSwitch and rapsLcClear. The others are either read-only values or not yet defined by the standard.
Status: current	Access: read-create
OBJECT-TYPE
	PrvtRingEpsLocalCommandType

prvtRingEpsControlVlan		1.3.6.1.4.1.738.1.5.134.1.1.1.1.6
The vlan ID used for RAPS & CFM traffic.
Status: current	Access: read-create
OBJECT-TYPE
	VlanIdOrNone

prvtRingEpsPort0Ifindex		1.3.6.1.4.1.738.1.5.134.1.1.1.1.7
This variable is the interface index of the interface either a bridge port, or an aggregated IEEE 802.1 link within a bridge port, attached to the ring as port 0.
Status: current	Access: read-create
OBJECT-TYPE
	InterfaceIndexOrZero

prvtRingEpsPort1Ifindex		1.3.6.1.4.1.738.1.5.134.1.1.1.1.8
This variable is the interface index of the interface either a bridge port, or an aggregated IEEE 802.1 link within a bridge port, attached to the ring as port 1.
Status: current	Access: read-create
OBJECT-TYPE
	InterfaceIndexOrZero

prvtRingEpsRplPort		1.3.6.1.4.1.738.1.5.134.1.1.1.1.9
This object controls whether the one of the ring ports is designated as RPL for the ring or not.
Status: current	Access: read-create
OBJECT-TYPE
	PrvtRingEpsRplPortType

prvtRingEpsManualSwitchPort		1.3.6.1.4.1.738.1.5.134.1.1.1.1.10
The port blocked by the Manual Switch command
Status: current	Access: read-create
OBJECT-TYPE
	PrvtRingEpsRplPortType

prvtRingEpsCfmMdLevel		1.3.6.1.4.1.738.1.5.134.1.1.1.1.11
Value of the CFM MD level where the protected domain is situated
Status: current	Access: read-create
OBJECT-TYPE
	Dot1agCfmMDLevelOrNone

prvtRingEpsPort0Mep		1.3.6.1.4.1.738.1.5.134.1.1.1.1.12
This variable is the peer MEP ID that should send CCMs towards port 0.
Status: current	Access: read-create
OBJECT-TYPE
	Dot1agCfmMepIdOrZero

prvtRingEpsPort1Mep		1.3.6.1.4.1.738.1.5.134.1.1.1.1.13
This variable is the peer MEP ID that should send CCMs towards port 1.
Status: current	Access: read-create
OBJECT-TYPE
	Dot1agCfmMepIdOrZero

prvtRingEpsRevertive		1.3.6.1.4.1.738.1.5.134.1.1.1.1.14
This is the MI_RAPS_Revertive variable defined in the standard. It controls whether the RPL is blocked again after a failure of some ring link recovers.
Status: current	Access: read-create
OBJECT-TYPE
	TruthValue

prvtRingEpsNoVirtualChannel		1.3.6.1.4.1.738.1.5.134.1.1.1.1.15
Node is part of a subring that doesn't use RAPS virtual channel
Status: current	Access: read-create
OBJECT-TYPE
	TruthValue

prvtRingEpsHoldOffTimer		1.3.6.1.4.1.738.1.5.134.1.1.1.1.16
Range is from 0 to 10 seconds in 100msec intervals
Status: current	Access: read-create
OBJECT-TYPE
	Unsigned32	0..10000

prvtRingEpsWaitToRestoreTimer		1.3.6.1.4.1.738.1.5.134.1.1.1.1.17
Range is from 1 to 12 minutes
Status: current	Access: read-create
OBJECT-TYPE
	Unsigned32	1..12

prvtRingEpsGuardTimer		1.3.6.1.4.1.738.1.5.134.1.1.1.1.18
Range is from 10msec to 2 seconds in 10msec intervals
Status: current	Access: read-create
OBJECT-TYPE
	Unsigned32	10..2000

prvtRingEpsWaitToBlockTimer		1.3.6.1.4.1.738.1.5.134.1.1.1.1.19
Range is from 5010msec to 7 seconds in 10msec intervals. This time is actulally the Guard Timer + 5 seconds
Status: current	Access: read-only
OBJECT-TYPE
	Unsigned32	5010..7000

prvtRingEpsDefectFop		1.3.6.1.4.1.738.1.5.134.1.1.1.1.20
So far only the situation when two or more RPL-owners are defined in the ring is identified as a defect. This scenario is noticed when the instance with the RPL-Owner role receives a RAPS packet with the RB bit set in its status field from a different NodeID than its own.
Status: current	Access: read-only
OBJECT-TYPE
	PrvtRingEpsDefectType

prvtRingEpsPort0Status		1.3.6.1.4.1.738.1.5.134.1.1.1.1.21
This variable reflects the state of port 0. It can be either Ok (unblocked), Blocked or Failed.
Status: current	Access: read-only
OBJECT-TYPE
	PrvtRingEpsPortStatusType

prvtRingEpsPort1Status		1.3.6.1.4.1.738.1.5.134.1.1.1.1.22
This variable reflects the state of port 1. It can be either Ok (unblocked), Blocked or Failed.
Status: current	Access: read-only
OBJECT-TYPE
	PrvtRingEpsPortStatusType

prvtRingEpsPort0PeerNodeId		1.3.6.1.4.1.738.1.5.134.1.1.1.1.23
This variable reflects the Node ID from the RAPS packet received via port 0.
Status: current	Access: read-only
OBJECT-TYPE
	MacAddress

prvtRingEpsPort1PeerNodeId		1.3.6.1.4.1.738.1.5.134.1.1.1.1.24
This variable reflects the Node ID from the RAPS packet received via port 1.
Status: current	Access: read-only
OBJECT-TYPE
	MacAddress

prvtRingEpsPort0PeerCommand		1.3.6.1.4.1.738.1.5.134.1.1.1.1.25
This variable reflects the Request/State of the RAPS packet received via port 0.
Status: current	Access: read-only
OBJECT-TYPE
	PrvtRingEpsRemoteRequestType

prvtRingEpsPort1PeerCommand		1.3.6.1.4.1.738.1.5.134.1.1.1.1.26
This variable reflects the Request/State of the RAPS packet received via port 1.
Status: current	Access: read-only
OBJECT-TYPE
	PrvtRingEpsRemoteRequestType

prvtRingEpsPort0PeerStatus		1.3.6.1.4.1.738.1.5.134.1.1.1.1.27
This variable reflects the status field of the RAPS packet received via port 0.
Status: current	Access: read-only
OBJECT-TYPE
	PrvtRingEpsPeerStatusType

prvtRingEpsPort1PeerStatus		1.3.6.1.4.1.738.1.5.134.1.1.1.1.28
This variable reflects the status field of the RAPS packet received via port 1.
Status: current	Access: read-only
OBJECT-TYPE
	PrvtRingEpsPeerStatusType

prvtRingEpsOperationalStatus		1.3.6.1.4.1.738.1.5.134.1.1.1.1.29
The purpose of this status is to identify to the user whether this instance is ready for running. The operational status can be up or down. When creating the instance the operational status will be down. Receiving CCMs from the expected peer MEPs on both ring ports will bring the operational status to up. If any needed CFM configuration is removed the operational status will go back to down
Status: current	Access: read-only
OBJECT-TYPE
	TruthValue

prvtRingEpsAdminStatus		1.3.6.1.4.1.738.1.5.134.1.1.1.1.30
Administrative status of the instance
Status: current	Access: read-create
OBJECT-TYPE
	TruthValue

prvtRingEpsRowStatus		1.3.6.1.4.1.738.1.5.134.1.1.1.1.31
The status of the row.
Status: current	Access: read-create
OBJECT-TYPE
	RowStatus

prvtRingEpsForcedSwitchPort		1.3.6.1.4.1.738.1.5.134.1.1.1.1.32
The port blocked by the Forced Switch command
Status: current	Access: read-create
OBJECT-TYPE
	PrvtRingEpsRplPortType

prvtRingEpsInstanceDescription		1.3.6.1.4.1.738.1.5.134.1.1.1.1.33
RAPS instance description.
Status: current	Access: read-create
OBJECT-TYPE
	DisplayString

prvtRingEpsRingId		1.3.6.1.4.1.738.1.5.134.1.1.1.1.34
The last octet of the RAPS destination MAC address is designated as Ring ID (01-19-A7-00-00-[Ring ID]). As of G.8032v2 the destination MAC address '01-19-A7-00-00-01' is used. The usage of other MAC addresses is for further study.
Status: current	Access: read-create
OBJECT-TYPE
	Unsigned32	1..255

prvtRingEpsPort0MonitoringMethod		1.3.6.1.4.1.738.1.5.134.1.1.1.1.35
Raps monitoring methods for port 0: ccm - CCM messages and link status will be used for raps monitoring, link-status -Link status will be used for raps monitoring
Status: current	Access: read-write
OBJECT-TYPE
	INTEGER	ccm(1), link-status(2)

prvtRingEpsPort1MonitoringMethod		1.3.6.1.4.1.738.1.5.134.1.1.1.1.36
Raps monitoring methods for port 1: ccm - CCM messages and link status will be used for raps monitoring, link-status - Link status will be used for raps monitoring
Status: current	Access: read-write
OBJECT-TYPE
	INTEGER	ccm(1), link-status(2)

prvtRingEpsVlanTable		1.3.6.1.4.1.738.1.5.134.1.2.1
This table includes information about protected vlans and the ring instances that monitor them.
Status: current	Access: not-accessible
OBJECT-TYPE
	SEQUENCE OF
		PrvtRingEpsVlanEntry

prvtRingEpsVlanEntry		1.3.6.1.4.1.738.1.5.134.1.2.1.1
Connection between vlan IDs and the RAPS instance that monitors them
Status: current	Access: not-accessible
OBJECT-TYPE
	PrvtRingEpsVlanEntry

prvtRingEpsVlanIndex		1.3.6.1.4.1.738.1.5.134.1.2.1.1.1
The vlan ID.
Status: current	Access: not-accessible
OBJECT-TYPE
	Unsigned32	1..4094

prvtRingEpsInstance		1.3.6.1.4.1.738.1.5.134.1.2.1.1.2
RAPS instance that will monitor this vlan
Status: current	Access: read-create
OBJECT-TYPE
	Unsigned32	0..10

prvtRingEpsVlanRowStatus		1.3.6.1.4.1.738.1.5.134.1.2.1.1.3
The status of the row.
Status: current	Access: read-create
OBJECT-TYPE
	RowStatus

prvtRingEpsSubRingTable		1.3.6.1.4.1.738.1.5.134.1.3.1
Table containing information about the subring instances defined on this node.
Status: current	Access: not-accessible
OBJECT-TYPE
	SEQUENCE OF
		PrvtRingEpsSubRingEntry

prvtRingEpsSubRingEntry		1.3.6.1.4.1.738.1.5.134.1.3.1.1
Configuration of a subring that is interconnected to the main ring in an interconnection node
Status: current	Access: not-accessible
OBJECT-TYPE
	PrvtRingEpsSubRingEntry

prvtRingEpsSubRingIndex		1.3.6.1.4.1.738.1.5.134.1.3.1.1.1
A subring ID
Status: current	Access: not-accessible
OBJECT-TYPE
	Unsigned32	1..10

prvtRingEpsSubRingNodeRole		1.3.6.1.4.1.738.1.5.134.1.3.1.1.2
This variable identifies the role that the node will play inside the subring. The node can have two special roles, RPL owner or RPL neighbor, when the subring port is designated as RPL. The subring can have a single RPL owner and a single RPL neighbor, connected between eachother via the RPL. If the subring port is not designated as RPL, then the node should have the role of a Simple node
Status: current	Access: read-create
OBJECT-TYPE
	PrvtRingEpsNodeRoleType

prvtRingEpsSubRingState		1.3.6.1.4.1.738.1.5.134.1.3.1.1.3
This variable identifies the state of the subring node according to the standard state machine.
Status: current	Access: read-only
OBJECT-TYPE
	PrvtRingEpsStateType

prvtRingEpsSubRingLocalCommand		1.3.6.1.4.1.738.1.5.134.1.3.1.1.4
The user can control the ring using a set of commands allowing blocking and unblocking of ports. These commands are rapsLcManualSwitch, rapsLcForcedSwitch and rapsLcClear. The others are either read-only values or not yet defined by the standard.
Status: current	Access: read-create
OBJECT-TYPE
	PrvtRingEpsLocalCommandType

prvtRingEpsSubRingPortIfindex		1.3.6.1.4.1.738.1.5.134.1.3.1.1.5
This variable is the interface index of the interface either a bridge port, or an aggregated IEEE 802.1 link within a bridge port, attached to the subring.
Status: current	Access: read-create
OBJECT-TYPE
	InterfaceIndexOrZero

prvtRingEpsSubRingPortMep		1.3.6.1.4.1.738.1.5.134.1.3.1.1.6
This variable is the peer MEP ID that should send CCMs towards the subring port.
Status: current	Access: read-create
OBJECT-TYPE
	Dot1agCfmMepIdOrZero

prvtRingEpsSubRingRplPort		1.3.6.1.4.1.738.1.5.134.1.3.1.1.7
This object controls whether the subring port is designated as RPL for the subring or not.
Status: current	Access: read-create
OBJECT-TYPE
	PrvtRingEpsRplPortType

prvtRingEpsSubRingVirtualChannelVlan		1.3.6.1.4.1.738.1.5.134.1.3.1.1.8
The vlan ID used for Virtual Channel encapsulation
Status: current	Access: read-create
OBJECT-TYPE
	VlanIdOrNone

prvtRingEpsSubRingRevertive		1.3.6.1.4.1.738.1.5.134.1.3.1.1.9
This is the MI_RAPS_Revertive variable defined in the standard. It controls whether the RPL is blocked again after a failure of some subring link recovers.
Status: current	Access: read-create
OBJECT-TYPE
	TruthValue

prvtRingEpsSubRingHoldOffTimer		1.3.6.1.4.1.738.1.5.134.1.3.1.1.10
Range is from 0 to 10 seconds in 100msec intervals
Status: current	Access: read-create
OBJECT-TYPE
	Unsigned32	0..10000

prvtRingEpsSubRingWaitToRestoreTimer		1.3.6.1.4.1.738.1.5.134.1.3.1.1.11
Range is from 1 to 12 minutes
Status: current	Access: read-create
OBJECT-TYPE
	Unsigned32	1..12

prvtRingEpsSubRingGuardTimer		1.3.6.1.4.1.738.1.5.134.1.3.1.1.12
Range is from 10msec to 2 seconds in 10msec intervals
Status: current	Access: read-create
OBJECT-TYPE
	Unsigned32	10..2000

prvtRingEpsSubRingWaitToBlockTimer		1.3.6.1.4.1.738.1.5.134.1.3.1.1.13
Range is from 5010msec to 7 seconds in 10msec intervals. This time is actulally the Guard Timer + 5 seconds
Status: current	Access: read-only
OBJECT-TYPE
	Unsigned32	5010..7000

prvtRingEpsSubRingDefectFop		1.3.6.1.4.1.738.1.5.134.1.3.1.1.14
So far only the situation when two or more RPL-owners are defined in the ring is identified as a defect. This scenario is noticed when the instance with the RPL-Owner role receives a RAPS packet with the RB bit set in its status field from a different NodeID than its own.
Status: current	Access: read-only
OBJECT-TYPE
	PrvtRingEpsDefectType

prvtRingEpsSubRingPortStatus		1.3.6.1.4.1.738.1.5.134.1.3.1.1.15
This variable reflects the state of the subring port. It can be either Ok (unblocked), Blocked or Failed.
Status: current	Access: read-only
OBJECT-TYPE
	PrvtRingEpsPortStatusType

prvtRingEpsSubRingPortPeerNodeId		1.3.6.1.4.1.738.1.5.134.1.3.1.1.16
This variable reflects the Node ID from the RAPS packet received via the subring port.
Status: current	Access: read-only
OBJECT-TYPE
	MacAddress

prvtRingEpsSubRingPeerCommand		1.3.6.1.4.1.738.1.5.134.1.3.1.1.17
This variable reflects the Request/State of the RAPS packet received via the subring port.
Status: current	Access: read-only
OBJECT-TYPE
	PrvtRingEpsRemoteRequestType

prvtRingEpsSubRingPeerStatus		1.3.6.1.4.1.738.1.5.134.1.3.1.1.18
This variable reflects the status field of the RAPS packet received via the subring port.
Status: current	Access: read-only
OBJECT-TYPE
	PrvtRingEpsPeerStatusType

prvtRingEpsSubRingVcPeerNodeId		1.3.6.1.4.1.738.1.5.134.1.3.1.1.19
This variable reflects the Node ID from the RAPS packet received via the virtual channel.
Status: current	Access: read-only
OBJECT-TYPE
	MacAddress

prvtRingEpsSubRingVcPeerCommand		1.3.6.1.4.1.738.1.5.134.1.3.1.1.20
This variable reflects the Request/State of the RAPS packet received via the virtual channel.
Status: current	Access: read-only
OBJECT-TYPE
	PrvtRingEpsRemoteRequestType

prvtRingEpsSubRingVcPeerStatus		1.3.6.1.4.1.738.1.5.134.1.3.1.1.21
This variable reflects the status field of the RAPS packet received via the virtual channel.
Status: current	Access: read-only
OBJECT-TYPE
	PrvtRingEpsPeerStatusType

prvtRingEpsSubRingPropagateTC		1.3.6.1.4.1.738.1.5.134.1.3.1.1.22
This is the MI_RAPS_Propagate_TC variable mentioned in the standard. If this is enabled a flush in the subring will be followed by a flush in the main instance.
Status: current	Access: read-create
OBJECT-TYPE
	TruthValue

prvtRingEpsSubRingOperationalStatus		1.3.6.1.4.1.738.1.5.134.1.3.1.1.23
The purpose of this status is to identify to the user whether this instance is ready for running. The operational status can be up or down. When creating the instance the operational status will be down. Receiving CCMs from the expected peer MEP on the subring port will bring the operational status to up. If any needed CFM configuration is removed the operational status will go back to down
Status: current	Access: read-only
OBJECT-TYPE
	TruthValue

prvtRingEpsSubRingAdminStatus		1.3.6.1.4.1.738.1.5.134.1.3.1.1.24
Administrative status of the subring instance
Status: current	Access: read-create
OBJECT-TYPE
	TruthValue

prvtRingEpsSubRingRowStatus		1.3.6.1.4.1.738.1.5.134.1.3.1.1.25
The status of the row.
Status: current	Access: read-create
OBJECT-TYPE
	RowStatus

prvtRingEpsSubRingControlVlan		1.3.6.1.4.1.738.1.5.134.1.3.1.1.26
The vlan ID used for RAPS & CFM traffic.
Status: current	Access: read-create
OBJECT-TYPE
	VlanIdOrNone

prvtRingEpsSubRingDescription		1.3.6.1.4.1.738.1.5.134.1.3.1.1.27
RAPS instance sub-ring description.
Status: current	Access: read-create
OBJECT-TYPE
	DisplayString

prvtRingEpsSubRingRingId		1.3.6.1.4.1.738.1.5.134.1.3.1.1.28
The last octet of the RAPS destination MAC address is designated as Ring ID (01-19-A7-00-00-[Ring ID]). As of G.8032v2 the destination MAC address '01-19-A7-00-00-01' is used. The usage of other MAC addresses is for further study.
Status: current	Access: read-create
OBJECT-TYPE
	Unsigned32	1..255

prvtRingEpsSubRingMonitoringMethod		1.3.6.1.4.1.738.1.5.134.1.3.1.1.29
Raps monitoring methods for subring port: ccm - CCM messags and link status will be used for raps monitoring, link-status -Link status will be used for raps monitoring
Status: current	Access: read-write
OBJECT-TYPE
	INTEGER	ccm(1), link-status(2)

prvtRingEpsDefectAlarm		1.3.6.1.4.1.738.1.5.134.0.1
This trap will be sent by any instance when it notices a defect. So far only the situation when two or more RPL-owners are defined in the ring is identified as a defect. This scenario is noticed when the instance with the RPL-Owner role receives a RAPS packet with the RB bit set in its status field from a different NodeID than its own. The management entity receiving the notification can identify the system from the network source address of the notification, and can identify the instance reporting the change by the indices in the OID of the prvtRingEpsDefectFop variable in the notification.
Status: current	Access: read-write
NOTIFICATION-TYPE

prvtRingEpsSwitchoverAlarm		1.3.6.1.4.1.738.1.5.134.0.2
This trap will be sent by any instance when it changes state. The management entity receiving the notification can identify the system from the network source address of the notification, and can identify the instance reporting the change by the indices in the OID of the prvtRingEpsState variable in the notification.
Status: current	Access: read-write
NOTIFICATION-TYPE

prvtRingEpsSubRingDefectAlarm		1.3.6.1.4.1.738.1.5.134.0.3
This trap will be sent by any subring instance when it notices a defect. So far only the situation when two or more RPL-owners are defined in the ring is identified as a defect. This scenario is noticed when the instance with the RPL-Owner role receives a RAPS packet with the RB bit set in its status field from a different NodeID than its own. The management entity receiving the notification can identify the system from the network source address of the notification, and can identify the instance reporting the change by the indices in the OID of the prvtRingEpsDefectFop variable in the notification.
Status: current	Access: read-write
NOTIFICATION-TYPE

prvtRingEpsSubRingSwitchoverAlarm		1.3.6.1.4.1.738.1.5.134.0.4
This trap will be sent by any subring instance when it changes state. The management entity receiving the notification can identify the system from the network source address of the notification, and can identify the instance reporting the change by the indices in the OID of the prvtRingEpsSubRingState variable in the notification.
Status: current	Access: read-write
NOTIFICATION-TYPE

prvtRingEpsCompliances		1.3.6.1.4.1.738.1.5.134.2.1
OBJECT IDENTIFIER

prvtRingEpsGroups		1.3.6.1.4.1.738.1.5.134.2.2
OBJECT IDENTIFIER

prvtRingEpsGroup		1.3.6.1.4.1.738.1.5.134.2.2.1
Objects for the RAPS instances group.
Status: current	Access: read-write
OBJECT-GROUP

prvtRingEpsVlanGroup		1.3.6.1.4.1.738.1.5.134.2.2.2
Objects for the RAPS monitored vlans group.
Status: current	Access: read-write
OBJECT-GROUP

prvtRingEpsSubRingGroup		1.3.6.1.4.1.738.1.5.134.2.2.3
Objects for the RAPS subring group.
Status: current	Access: read-write
OBJECT-GROUP

prvtRingEpsNotificationsGroup		1.3.6.1.4.1.738.1.5.134.2.2.4
Objects for the Notifications group.
Status: current	Access: read-write
NOTIFICATION-GROUP

prvtRingEpsCompliance		1.3.6.1.4.1.738.1.5.134.2.1.1
The compliance statement for support of the Ring EPS MIB module.
Status: current	Access: read-write
MODULE-COMPLIANCE