PRVT-PW-TDM-MIB

Imported modules

SNMPv2-SMI	SNMPv2-CONF	SNMPv2-TC
IF-MIB	PerfHist-TC-MIB	Q-BRIDGE-MIB
PRVT-SWITCH-MIB

Imported symbols

MODULE-IDENTITY	OBJECT-TYPE	Integer32
Counter32	Unsigned32	Gauge32
IpAddress	MODULE-COMPLIANCE	NOTIFICATION-GROUP
OBJECT-GROUP	TEXTUAL-CONVENTION	TruthValue
RowStatus	StorageType	TimeStamp
NOTIFICATION-TYPE	transmission	InterfaceIndexOrZero
PerfCurrentCount	PerfIntervalCount	PortList
switch

Defined Types

PrvtPwVcTDMCfgIndex
Index into any of the relevant prvtPwVcXXXCfgTable.
TEXTUAL-CONVENTION
	Unsigned32

TimeSlotList
Each octet within this value specifies a time slot included in the give channel group. There should be 32 bits of 4 octets for each port of the CES module. Note that if the line type is set to T1 only the first 24 bits of each 4 octests can be set. The most significant bit of the list indicates timeslot 1 of port 1, the 33th bit - timeslot 1 of port 2, etc. If the bit is set, the port is included in the given channel group.
TEXTUAL-CONVENTION
	OCTET STRING

PrvtPwVcTDMCfgInterface
Interface of the given circuit used in TDM config for OC3 modules
TEXTUAL-CONVENTION
	IpAddress

InterfaceTimeSlot
The first 4 octets of this value represent the interface of the given channel group P.K.L.M.The last 32 bits of the 4 octets represent a bitmask of the time slots
TEXTUAL-CONVENTION
	OCTET STRING

PrvtPwVcTDMEntry
SEQUENCE
	prvtPwVcTDMModuleId	INTEGER
	prvtPwVcTDMCircuitId	INTEGER
	prvtPwVcTDMType	INTEGER
	prvtPwVcRelTDMCfgIndex	PrvtPwVcTDMCfgIndex
	prvtPwVcTDMTimeElapsed	Integer32
	prvtPwVcTDMValidIntervals	Integer32
	prvtPwVcTDMCurrentIndications	BITS
	prvtPwVcTDMLatchedIndications	BITS
	prvtPwVcTDMLastEsTimeStamp	TimeStamp
	prvtPwVcTDMEmulationMode	INTEGER
	prvtPwVcTDMOperStatus	INTEGER
	prvtPwVcTDMClearCircuitStatistics	INTEGER

PrvtPwVcTDMCfgEntry
SEQUENCE
	prvtPwVcTDMCfgPayloadSize	Unsigned32
	prvtPwVcTDMCfgPktReorder	TruthValue
	prvtPwVcTDMCfgRtpHdrUsed	TruthValue
	prvtPwVcTDMCfgJtrBfrDepth	Unsigned32
	prvtPwVcTDMCfgChannelGroup	INTEGER
	prvtPwVcTDMCfgPorts	OCTET STRING
	prvtPwVcTDMCfgPeerIpType	INTEGER
	prvtPwVcTDMCfgPeerIpAddress	IpAddress
	prvtPwVcTDMCfgPeerPort	INTEGER
	prvtPwVcTDMCfgPeerMAC	OCTET STRING
	prvtPwVcTDMCfgPeerEcid	INTEGER
	prvtPwVcTDMCfgPeerOosEcid	INTEGER
	prvtPwVcTDMCfgVlanId	INTEGER
	prvtPwVcTDMCfgVlanPrio	INTEGER
	prvtPwVcTDMCfgLocalPort	INTEGER
	prvtPwVcTDMCfgEcid	INTEGER
	prvtPwVcTDMCfgOosEcid	INTEGER
	prvtPwVcTDMCfgProtocol	INTEGER
	prvtPwVcTDMCfgAdminStatus	INTEGER
	prvtPwVcTDMCfgRowStatus	RowStatus
	prvtPwVcTDMCfgRtp	INTEGER
	prvtPwVcTDMCfgOosPort	Unsigned32
	prvtPwVcTDMCfgPayloadSuppression	INTEGER
	prvtPwVcTDMCfgInterface	PrvtPwVcTDMCfgInterface
	prvtPwVcTDMCfgIpTos	INTEGER
	prvtPwVcTDMCfgIpOosTos	INTEGER
	prvtPwVcTDMCfgPeerOosPort	INTEGER
	prvtPwVcTDMCfgMplsLocalLabel	Unsigned32
	prvtPwVcTDMCfgMplsPeerLabel	Unsigned32
	prvtPwVcTDMCfgMplsTTL	INTEGER
	prvtPwVcTDMCfgMplsExp	INTEGER
	prvtPwVcTDMCfgMplsOosLocalLabel	Unsigned32
	prvtPwVcTDMCfgMplsOosPeerLabel	Unsigned32
	prvtPwVcTDMCfgMplsOosTTL	INTEGER
	prvtPwVcTDMCfgMplsOosExp	INTEGER
	prvtPwVcTDMCfgRtpOosPayload	INTEGER
	prvtPwVcTDMCfgRtpPayload	INTEGER

PrvtTDMChannelGrpEntry
SEQUENCE
	prvtTDMChannelGrpModuleID	Unsigned32
	prvtTDMChannelGrpID	Unsigned32
	prvtTDMChannelGrpCfgError	INTEGER
	prvtTDMChannelGrpTimeSlots	TimeSlotList
	prvtTDMChannelGrpOC3TimeSlots	InterfaceTimeSlot

PrvtPwVcTDMPerfCurrentEntry
SEQUENCE
	prvtPwVcTDMPerfCurrentPktsOoseq	Counter32
	prvtPwVcTDMPerfCurrentJtrBfrUnderruns	Counter32
	prvtPwVcTDMPerfCurrentJtrBfrOverruns	Counter32
	prvtPwVcTDMPerfCurrentMalformedPkt	Counter32
	prvtPwVcTDMPerfCurrentNearEndFC	Counter32
	prvtPwVcTDMPerfCurrentFarEndFC	Counter32

PrvtPwVcTDMPerfIntervalEntry
SEQUENCE
	prvtPwVcTDMPerfIntervalNumber	Unsigned32
	prvtPwVcTDMPerfIntervalValidData	TruthValue
	prvtPwVcTDMPerfIntervalDuration	Integer32
	prvtPwVcTDMPerfIntervalPktsOoseq	Counter32
	prvtPwVcTDMPerfIntervalJtrBfrUnderruns	Counter32
	prvtPwVcTDMPerfIntervalJtrBfrOverruns	Counter32
	prvtPwVcTDMPerfIntervalMalformedPkt	Counter32
	prvtPwVcTDMPerfIntervalNearEndFC	Counter32
	prvtPwVcTDMPerfIntervalFarEndFC	Counter32

PrvtPwVcTDMPerfEntry
SEQUENCE
	prvtPwVcTDMPerfPktsOoseq	Counter32
	prvtPwVcTDMPerfJtrBfrUnderruns	Counter32
	prvtPwVcTDMPerfJtrBfrOverruns	Counter32
	prvtPwVcTDMPerfMalformedPkt	Counter32
	prvtPwVcTDMPerfNearEndFC	Counter32
	prvtPwVcTDMPerfFarEndFC	Counter32
	prvtPwVcTDMPerfDiscontinuityTime	TimeStamp

PrvtPwVcTDMAlarmEntry
SEQUENCE
	prvtPwVcTDMAlarmIndex	Gauge32
	prvtPwVcTDMAlarmVariable	OBJECT IDENTIFIER
	prvtPwVcTDMAlarmThreshold	INTEGER
	prvtPwVcTDMAlarmValue	INTEGER

Defined Values

prvtPwVcTDMMIB		1.3.6.1.4.1.738.1.5.200.2
This MIB contains managed object definitions for encapsulating TDM (T1, E1, T3, E3, NxDS0) as pseudo-wires over packet-switching networks (PSN).
MODULE-IDENTITY

prvtPwVc		1.3.6.1.4.1.738.1.5.200
OBJECT IDENTIFIER

prvtPwVcTDMObjects		1.3.6.1.4.1.738.1.5.200.2.1
OBJECT IDENTIFIER

prvtPwVcTDMTraps		1.3.6.1.4.1.738.1.5.200.2.2
OBJECT IDENTIFIER

prvtPwVcTDMConformance		1.3.6.1.4.1.738.1.5.200.2.3
OBJECT IDENTIFIER

prvtPwVcTDMTable		1.3.6.1.4.1.738.1.5.200.2.1.1
This table contains basic information including ifIndex, and pointers to entries in the relevant TDM config tables for this TDM PW.
Status: current	Access: not-accessible
OBJECT-TYPE
	SEQUENCE OF
		PrvtPwVcTDMEntry

prvtPwVcTDMEntry		1.3.6.1.4.1.738.1.5.200.2.1.1.1
This table is indexed by the same index that was created for the associated entry in the PW Table (in the PW-STD-MIB). An entry is created in this table by the agent for every entry in the prvtPwVcTable with a prvtPwVcType of 'TDM'.
Status: current	Access: not-accessible
OBJECT-TYPE
	PrvtPwVcTDMEntry

prvtPwVcTDMModuleId		1.3.6.1.4.1.738.1.5.200.2.1.1.1.1
The ID of the CES Module where the crcuit is configured.
Status: current	Access: read-only
OBJECT-TYPE
	INTEGER	1..65535

prvtPwVcTDMCircuitId		1.3.6.1.4.1.738.1.5.200.2.1.1.1.2
The ID of the CES Circuit that this PW represents.
Status: current	Access: read-only
OBJECT-TYPE
	INTEGER	1..65535

prvtPwVcTDMType		1.3.6.1.4.1.738.1.5.200.2.1.1.1.3
Specifies the type of TDM PW. The connection assumed to be symmetrical having the same value at both ends. To identify structured vs. unstructured type for DS1 and E1, dsx1LineType and dsx1SignalMode [DS1MIB] should be referenced. DS3 and E3 are always unstructured.
Status: current	Access: read-only
OBJECT-TYPE
	INTEGER	other(1), ds1(2), e1(3), ds3(4), e3(5), octetAlignedT1(6), nXds0(7), nXds0WithCASe1(8), nXds0WithCASds1Esf(9), nXds0WithCASds1Sf(10)

prvtPwVcRelTDMCfgIndex		1.3.6.1.4.1.738.1.5.200.2.1.1.1.4
Index to the relevant TDM configuration table entry that appears in one of the related MIB modules such as SAToP, TDMoIP or CESoPSN. It is likely that multiple TDM PWs of the same characteristic will share a single configuration entry of the relevant type.
Status: current	Access: read-only
OBJECT-TYPE
	PrvtPwVcTDMCfgIndex

prvtPwVcTDMTimeElapsed		1.3.6.1.4.1.738.1.5.200.2.1.1.1.5
The number of seconds, including partial seconds, that have elapsed since the beginning of the current measurement period. If, for some reason, such as an adjustment in the system's time-of-day clock, the current interval exceeds the maximum value, the agent will return the maximum value.
Status: current	Access: read-only
OBJECT-TYPE
	Integer32	1..900

prvtPwVcTDMValidIntervals		1.3.6.1.4.1.738.1.5.200.2.1.1.1.6
The number of previous 15-minute intervals for which data was collected. An agent with TDM capability must be capable of supporting at least n intervals. The minimum value of n is 4, The default of n is 32 and the maximum value of n is 96. The value will be unless the measurement was (re-) started within the last (*15) minutes, in which case the value will be the number of complete 15 minute intervals for which the agent has at least some data. In certain cases(e.g., in the case where the agent is a proxy) it is possible that some intervals are unavailable. In this case, this interval is the maximum interval number for which data is available.
Status: current	Access: read-only
OBJECT-TYPE
	Integer32	0..96

prvtPwVcTDMCurrentIndications		1.3.6.1.4.1.738.1.5.200.2.1.1.1.7
The following defects should be detected and reported upon request: -Stray packets MAY be detected by the PSN and multiplexing layers. Stray packets MUST be discarded by the CE-bound IWF and their detection MUST NOT affect mechanisms for detection of packet loss. -Malformed packets are detected by mismatch between the expected packet size (taking the value of the L bit into account) and the actual packet size inferred from the PSN and multiplexing layers. Malformed in-order packets MUST be discarded by the CE-bound IWF and replacement data generated as for lost packets. -Excessive packet loss rate is detected by computing the average packet loss rate over the value of prvtPwVcTDMAvePktLossTimeWindow and comparing it with a preconfigured threshold [SATOP]. -Buffer overrun is detected in the normal operation state when the CE bound IWF's jitter buffer cannot accommodate newly arrived packets. -Remote packet loss is indicated by reception of packets with their R bit set. -Packet misorder is detected by looking at the Sequence number provided by the control word. -TDM Fault, if L bit in the control word is set, it indicates that TDM data carried in the payload is invalid due an attachment circuit fault. When the L bit is set the payload MAY be omitted in order to conserve bandwidth. Note: the algorithm used to capture these indications is implementation specific.
Status: current	Access: read-only
OBJECT-TYPE
	BITS	other(0), strayPacket(1), malformedPacket(2), excessivePktLossRate(3), bufferOverrun(4), bufferUnderrun(5), remotePktLoss(6), packetLoss(7), tdmFault(8), packetsLbitCounter(9), packetsRbitCounter(10)

prvtPwVcTDMLatchedIndications		1.3.6.1.4.1.738.1.5.200.2.1.1.1.8
The state of TDM indicators when the TDM PW last declared an error second (either as ES, SES or a second with errors inside a UAS) condition. At this time, only LOPS can create a failure. Since indicators other than LOPS are useful, all are latched here. For bit definitions, see prvtPwVcTDMCurrentIndications above. Note: the algorithm used to latch these indications when entering an defect state is implementation specific.
Status: current	Access: read-only
OBJECT-TYPE
	BITS	other(0), staryPacket(1), malformedPacket(2), excessivePktLossRate(3), bufferOverrun(4), bufferUnderrun(5), remotePktLoss(6), packetLoss(7), tdmFault(8), packetsLbitCounter(9), packetsRbitCounter(10)

prvtPwVcTDMLastEsTimeStamp		1.3.6.1.4.1.738.1.5.200.2.1.1.1.9
The value of sysUpTime on the most recent occasion at which the TDM PW entered the ES or SES state.
Status: current	Access: read-only
OBJECT-TYPE
	TimeStamp

prvtPwVcTDMEmulationMode		1.3.6.1.4.1.738.1.5.200.2.1.1.1.10
The circuit emulation mode.
Status: current	Access: read-only
OBJECT-TYPE
	INTEGER	undefined(0), structured(1), unstuctured(2)

prvtPwVcTDMOperStatus		1.3.6.1.4.1.738.1.5.200.2.1.1.1.11
The operational status of the circuit.
Status: current	Access: read-only
OBJECT-TYPE
	INTEGER	up(1), down(2)

prvtPwVcTDMClearCircuitStatistics		1.3.6.1.4.1.738.1.5.200.2.1.1.1.12
Clear circuit statistics.
Status: current	Access: read-write
OBJECT-TYPE
	INTEGER	none(0), clear(1)

prvtPwVcTDMCfgTable		1.3.6.1.4.1.738.1.5.200.2.1.3
This table contains a set of parameters that may be referenced by one or more TDM PWs in prvtPwVcTDMTable.
Status: current	Access: not-accessible
OBJECT-TYPE
	SEQUENCE OF
		PrvtPwVcTDMCfgEntry

prvtPwVcTDMCfgEntry		1.3.6.1.4.1.738.1.5.200.2.1.3.1
These parameters define the characteristics of a TDM PW. They are grouped here to ease NMS burden. Once an entry is created here it may be re-used by many PWs.
Status: current	Access: not-accessible
OBJECT-TYPE
	PrvtPwVcTDMCfgEntry

prvtPwVcTDMCfgPayloadSize		1.3.6.1.4.1.738.1.5.200.2.1.3.1.1
The value of this object indicates the PayLoad Size to be defined during the PW setUp. Upon TX, implementation must be capable of carrying that amount of data. Upon RX, When the LEN field is set to 0, the payload of packet MUST assume this size, and if the actual packet size is inconsistent with this length, the packet MUST be considered to be malformed.
Status: current	Access: read-create
OBJECT-TYPE
	Unsigned32

prvtPwVcTDMCfgPktReorder		1.3.6.1.4.1.738.1.5.200.2.1.3.1.2
If set True: as CE bound packets are queued in the jitter buffer, out of order packets are re-ordered. The maximum sequence number differential (i.e., the range in which re-sequencing can occur) is dependant on the depth of the jitter buffer. See prvtPwVcTDMCfgJtrBfrDepth. NOTE: Some implementations may not support this feature. The agent is then required to set this False.
Status: current	Access: read-create
OBJECT-TYPE
	TruthValue

prvtPwVcTDMCfgRtpHdrUsed		1.3.6.1.4.1.738.1.5.200.2.1.3.1.3
If set False: an RTP header is not pre-pended to the TDM packet.
Status: current	Access: read-create
OBJECT-TYPE
	TruthValue

prvtPwVcTDMCfgJtrBfrDepth		1.3.6.1.4.1.738.1.5.200.2.1.3.1.4
The size of the Jitter buffer SHOULD be defined to a value that is capable to allow accommodation to the PSN-specific packet delay variation. If configured to a value not supported by the implementation, the agent MUST return an error code 'jtrBfrDepth' in 'prvtPwVcTDMConfigError ' NOTE: jitter buffers are a limited resource to be managed.
Status: current	Access: read-create
OBJECT-TYPE
	Unsigned32	1..200

prvtPwVcTDMCfgChannelGroup		1.3.6.1.4.1.738.1.5.200.2.1.3.1.5
The circuit's channel group. This object is only valid if structured emulation mode is used. If a group is not set the value of the object is 0.
Status: current	Access: read-create
OBJECT-TYPE
	INTEGER	1..128

prvtPwVcTDMCfgPorts		1.3.6.1.4.1.738.1.5.200.2.1.3.1.6
A bitmap of themodule's TDM ports belongng to the circuit.
Status: current	Access: read-create
OBJECT-TYPE
	OCTET STRING

prvtPwVcTDMCfgPeerIpType		1.3.6.1.4.1.738.1.5.200.2.1.3.1.7
The type of the peer's IP address.
Status: current	Access: read-create
OBJECT-TYPE
	INTEGER	ipv4(4), ipv6(6), dns(16)

prvtPwVcTDMCfgPeerIpAddress		1.3.6.1.4.1.738.1.5.200.2.1.3.1.8
The peer's IP address.
Status: current	Access: read-create
OBJECT-TYPE
	IpAddress

prvtPwVcTDMCfgPeerPort		1.3.6.1.4.1.738.1.5.200.2.1.3.1.9
The connection port.
Status: current	Access: read-create
OBJECT-TYPE
	INTEGER	0..65535

prvtPwVcTDMCfgPeerMAC		1.3.6.1.4.1.738.1.5.200.2.1.3.1.10
The Peer MAC address. This object is only valid for Metro-Ethernet and Mpls circuits. If an IP address is configured for the circuit, this object will display the resolved MAC address.
Status: current	Access: read-create
OBJECT-TYPE
	OCTET STRING

prvtPwVcTDMCfgPeerEcid		1.3.6.1.4.1.738.1.5.200.2.1.3.1.11
The peer circuit identifier. This object is only valid if the Circuit protocol is metro-ethernet.
Status: current	Access: read-create
OBJECT-TYPE
	INTEGER

prvtPwVcTDMCfgPeerOosEcid		1.3.6.1.4.1.738.1.5.200.2.1.3.1.12
The peer circuit identifier for the out-of-band signaling. This value is valid only when the object prvtPwVcTDMCfgEcid is set and when the current protocol is metro-ethernet
Status: current	Access: read-create
OBJECT-TYPE
	INTEGER

prvtPwVcTDMCfgVlanId		1.3.6.1.4.1.738.1.5.200.2.1.3.1.13
The circuit Vlan ID.
Status: current	Access: read-create
OBJECT-TYPE
	INTEGER	2..4094

prvtPwVcTDMCfgVlanPrio		1.3.6.1.4.1.738.1.5.200.2.1.3.1.14
The prioirty for the VLAN set here, when the protocol for the circuit is metro-ethernet
Status: current	Access: read-create
OBJECT-TYPE
	INTEGER	0..7

prvtPwVcTDMCfgLocalPort		1.3.6.1.4.1.738.1.5.200.2.1.3.1.15
Local UDP port.
Status: current	Access: read-create
OBJECT-TYPE
	INTEGER	0..65535

prvtPwVcTDMCfgEcid		1.3.6.1.4.1.738.1.5.200.2.1.3.1.16
The local circuit identifier. This object is only valid if the Circuit protocol is metro-ethernet.
Status: current	Access: read-create
OBJECT-TYPE
	INTEGER

prvtPwVcTDMCfgOosEcid		1.3.6.1.4.1.738.1.5.200.2.1.3.1.17
The local circuit identifier for the out-of-band signaling. This value is valid only when the object prvtPwVcTDMCfgEcid is set and when the current protocol is metro-ethernet
Status: current	Access: read-create
OBJECT-TYPE
	INTEGER

prvtPwVcTDMCfgProtocol		1.3.6.1.4.1.738.1.5.200.2.1.3.1.18
The emulation protocol.
Status: current	Access: read-create
OBJECT-TYPE
	INTEGER	undefined(0), satop(1), cesopsn(2), metro-ethernet(3), mpls(4)

prvtPwVcTDMCfgAdminStatus		1.3.6.1.4.1.738.1.5.200.2.1.3.1.19
The administrative status of the circuit.
Status: current	Access: read-create
OBJECT-TYPE
	INTEGER	enable(1), disable(2)

prvtPwVcTDMCfgRowStatus		1.3.6.1.4.1.738.1.5.200.2.1.3.1.20
This field is used to create and destroy TDM circuits.
Status: current	Access: read-create
OBJECT-TYPE
	RowStatus

prvtPwVcTDMCfgRtp		1.3.6.1.4.1.738.1.5.200.2.1.3.1.21
TRTP header.
Status: current	Access: read-create
OBJECT-TYPE
	INTEGER	true(1), false(2)

prvtPwVcTDMCfgOosPort		1.3.6.1.4.1.738.1.5.200.2.1.3.1.22
Oos port.
Status: current	Access: read-create
OBJECT-TYPE
	Unsigned32	0..65535

prvtPwVcTDMCfgPayloadSuppression		1.3.6.1.4.1.738.1.5.200.2.1.3.1.23
Controls payload suppression. Object does not require module to be restarted.
Status: current	Access: read-create
OBJECT-TYPE
	INTEGER	enable(1), disable(2)

prvtPwVcTDMCfgInterface		1.3.6.1.4.1.738.1.5.200.2.1.3.1.24
Interface used for configuring OC3 TDM circuits P - Port Number, K, L, M standard numbering of SONET/SDH.
Status: current	Access: read-create
OBJECT-TYPE
	PrvtPwVcTDMCfgInterface

prvtPwVcTDMCfgIpTos		1.3.6.1.4.1.738.1.5.200.2.1.3.1.25
Set/Show IP TOS information
Status: current	Access: read-create
OBJECT-TYPE
	INTEGER	0..255

prvtPwVcTDMCfgIpOosTos		1.3.6.1.4.1.738.1.5.200.2.1.3.1.26
Set/Show IP Out Of Stream information
Status: current	Access: read-create
OBJECT-TYPE
	INTEGER	0..255

prvtPwVcTDMCfgPeerOosPort		1.3.6.1.4.1.738.1.5.200.2.1.3.1.27
This field is used to SET Destination Oos Port
Status: current	Access: read-create
OBJECT-TYPE
	INTEGER	0..65535

prvtPwVcTDMCfgMplsLocalLabel		1.3.6.1.4.1.738.1.5.200.2.1.3.1.28
The local circuit identifier. This object is only valid if the Circuit protocol is MPLS
Status: current	Access: read-create
OBJECT-TYPE
	Unsigned32	0..1048575

prvtPwVcTDMCfgMplsPeerLabel		1.3.6.1.4.1.738.1.5.200.2.1.3.1.29
The peer circuit identifier. This object is only valid if the Circuit protocol is MPLS
Status: current	Access: read-create
OBJECT-TYPE
	Unsigned32	0..1048575

prvtPwVcTDMCfgMplsTTL		1.3.6.1.4.1.738.1.5.200.2.1.3.1.30
MPLS TTL
Status: current	Access: read-create
OBJECT-TYPE
	INTEGER	2..255

prvtPwVcTDMCfgMplsExp		1.3.6.1.4.1.738.1.5.200.2.1.3.1.31
MPLS EXP
Status: current	Access: read-create
OBJECT-TYPE
	INTEGER	0..7

prvtPwVcTDMCfgMplsOosLocalLabel		1.3.6.1.4.1.738.1.5.200.2.1.3.1.32
The local circuit identifier for the out-of-band signaling. This object is only valid if the Circuit protocol is MPLS
Status: current	Access: read-create
OBJECT-TYPE
	Unsigned32	0..1048575

prvtPwVcTDMCfgMplsOosPeerLabel		1.3.6.1.4.1.738.1.5.200.2.1.3.1.33
The peer circuit identifier for the out-of-band signaling. This object is only valid if the Circuit protocol is MPLS
Status: current	Access: read-create
OBJECT-TYPE
	Unsigned32	0..1048575

prvtPwVcTDMCfgMplsOosTTL		1.3.6.1.4.1.738.1.5.200.2.1.3.1.34
MPLS TTL for the out-of-band signaling.
Status: current	Access: read-create
OBJECT-TYPE
	INTEGER	2..255

prvtPwVcTDMCfgMplsOosExp		1.3.6.1.4.1.738.1.5.200.2.1.3.1.35
MPLS EXP for the out-of-band signaling.
Status: current	Access: read-create
OBJECT-TYPE
	INTEGER	0..7

prvtPwVcTDMCfgRtpOosPayload		1.3.6.1.4.1.738.1.5.200.2.1.3.1.36
This field is used to SET RTP Oos payload type.
Status: current	Access: read-create
OBJECT-TYPE
	INTEGER	0..127

prvtPwVcTDMCfgRtpPayload		1.3.6.1.4.1.738.1.5.200.2.1.3.1.37
This field is used to SET RTP payload type.
Status: current	Access: read-create
OBJECT-TYPE
	INTEGER	0..127

prvtTDMChannelGrpTable		1.3.6.1.4.1.738.1.5.200.2.1.4
This table contains the set of available channel groups.
Status: current	Access: not-accessible
OBJECT-TYPE
	SEQUENCE OF
		PrvtTDMChannelGrpEntry

prvtTDMChannelGrpEntry		1.3.6.1.4.1.738.1.5.200.2.1.4.1
These parameters are used to configure a CES channel group.
Status: current	Access: not-accessible
OBJECT-TYPE
	PrvtTDMChannelGrpEntry

prvtTDMChannelGrpModuleID		1.3.6.1.4.1.738.1.5.200.2.1.4.1.1
The index of the module to which this channel group belongs.
Status: current	Access: read-only
OBJECT-TYPE
	Unsigned32

prvtTDMChannelGrpID		1.3.6.1.4.1.738.1.5.200.2.1.4.1.2
The channel group ID.
Status: current	Access: read-only
OBJECT-TYPE
	Unsigned32

prvtTDMChannelGrpCfgError		1.3.6.1.4.1.738.1.5.200.2.1.4.1.3
This object displays the correctness of the configuration. If it has a value of channelGroupAtached(1) this channel group has been attached to a circuit and the new configuration cannot be applied.
Status: current	Access: read-only
OBJECT-TYPE
	INTEGER	noError(0), channelGroupAtached(1)

prvtTDMChannelGrpTimeSlots		1.3.6.1.4.1.738.1.5.200.2.1.4.1.4
This object is used to configure which time slots are members of the given channel group.
Status: current	Access: read-write
OBJECT-TYPE
	TimeSlotList

prvtTDMChannelGrpOC3TimeSlots		1.3.6.1.4.1.738.1.5.200.2.1.4.1.5
This object is used to configure interface and time slots for the given channel group in OC3 module.
Status: current	Access: read-write
OBJECT-TYPE
	InterfaceTimeSlot

prvtPwVcTDMPerfCurrentTable		1.3.6.1.4.1.738.1.5.200.2.1.5
The current 15 minute interval counts are in this table. This table provides per TDM PW performance information.
Status: current	Access: not-accessible
OBJECT-TYPE
	SEQUENCE OF
		PrvtPwVcTDMPerfCurrentEntry

prvtPwVcTDMPerfCurrentEntry		1.3.6.1.4.1.738.1.5.200.2.1.5.1
An entry in this table is created by the agent for every prvtPwVcTDM entry. After 15 minutes, the contents of this table entry are copied to a new entry in the prvtPwVcTDMPerfInterval table and the counts in this entry are reset to zero.
Status: current	Access: not-accessible
OBJECT-TYPE
	PrvtPwVcTDMPerfCurrentEntry

prvtPwVcTDMPerfCurrentPktsOoseq		1.3.6.1.4.1.738.1.5.200.2.1.5.1.1
Number of packets detected out of sequence (via TDM header sequence numbers), but successfully re-ordered. Note: some implementations may not support this Feature.
Status: current	Access: read-only
OBJECT-TYPE
	Counter32

prvtPwVcTDMPerfCurrentJtrBfrUnderruns		1.3.6.1.4.1.738.1.5.200.2.1.5.1.2
Number of times a packet needed to be played out and the jitter buffer was empty.
Status: current	Access: read-only
OBJECT-TYPE
	Counter32

prvtPwVcTDMPerfCurrentJtrBfrOverruns		1.3.6.1.4.1.738.1.5.200.2.1.5.1.3
Number of packets detected out of range (via TDM header sequence numbers), and could not be re- ordered, or could not fit in the jitter buffer.
Status: current	Access: read-only
OBJECT-TYPE
	Counter32

prvtPwVcTDMPerfCurrentMalformedPkt		1.3.6.1.4.1.738.1.5.200.2.1.5.1.4
Number of packets detected with unexpected size, or bad headers' stack
Status: current	Access: read-only
OBJECT-TYPE
	Counter32

prvtPwVcTDMPerfCurrentNearEndFC		1.3.6.1.4.1.738.1.5.200.2.1.5.1.5
Number of local packet failures.
Status: current	Access: read-only
OBJECT-TYPE
	Counter32

prvtPwVcTDMPerfCurrentFarEndFC		1.3.6.1.4.1.738.1.5.200.2.1.5.1.6
Number of remote packet failures.
Status: current	Access: read-only
OBJECT-TYPE
	Counter32

prvtPwVcTDMPerfIntervalTable		1.3.6.1.4.1.738.1.5.200.2.1.6
This table provides performance information per TDM PW similar to the prvtPwVcTDMPerfCurrentTable above. However, these counts represent historical 15 minute intervals. Typically, this table will have a maximum of 96 entries for a 24 hour period, but is not limited to this.
Status: current	Access: not-accessible
OBJECT-TYPE
	SEQUENCE OF
		PrvtPwVcTDMPerfIntervalEntry

prvtPwVcTDMPerfIntervalEntry		1.3.6.1.4.1.738.1.5.200.2.1.6.1
An entry in this table is created by the agent for every prvtPwVcTDMPerfCurrentEntry that is 15 minutes old. The contents of the Current entry are copied to the new entry here. The Current entry, then resets its counts to zero for the next current 15 minute interval.
Status: current	Access: not-accessible
OBJECT-TYPE
	PrvtPwVcTDMPerfIntervalEntry

prvtPwVcTDMPerfIntervalNumber		1.3.6.1.4.1.738.1.5.200.2.1.6.1.1
A number (normally between 1 and 96 to cover a 24 hour period) which identifies the interval for which the set of statistics is available. The interval identified by 1 is the most recently completed 15 minute interval, and the interval identified by N is the interval immediately preceding the one identified by N-1. The minimum range of N is 1 through 4. The default range is 1 through 32. The maximum value of N is 1 through 96.
Status: current	Access: not-accessible
OBJECT-TYPE
	Unsigned32

prvtPwVcTDMPerfIntervalValidData		1.3.6.1.4.1.738.1.5.200.2.1.6.1.2
This variable indicates if the data for this interval is valid.
Status: current	Access: read-only
OBJECT-TYPE
	TruthValue

prvtPwVcTDMPerfIntervalDuration		1.3.6.1.4.1.738.1.5.200.2.1.6.1.3
The duration of a particular interval in seconds, Adjustments in the system's time-of-day clock, may cause the interval to be greater or less than, the normal value. Therefore this actual interval value is provided.
Status: current	Access: read-only
OBJECT-TYPE
	Integer32

prvtPwVcTDMPerfIntervalPktsOoseq		1.3.6.1.4.1.738.1.5.200.2.1.6.1.4
Number of packets detected out of sequence (via TDM header sequence numbers), but successfully re-ordered. Note: some implementations mat not support this feature.
Status: current	Access: read-only
OBJECT-TYPE
	Counter32

prvtPwVcTDMPerfIntervalJtrBfrUnderruns		1.3.6.1.4.1.738.1.5.200.2.1.6.1.5
Number of times a packet needed to be played out and the jitter buffer was empty.
Status: current	Access: read-only
OBJECT-TYPE
	Counter32

prvtPwVcTDMPerfIntervalJtrBfrOverruns		1.3.6.1.4.1.738.1.5.200.2.1.6.1.6
Number of packets detected out of range (via TDM header sequence numbers), and could not be re- ordered, or could not fit in the jitter buffer.
Status: current	Access: read-only
OBJECT-TYPE
	Counter32

prvtPwVcTDMPerfIntervalMalformedPkt		1.3.6.1.4.1.738.1.5.200.2.1.6.1.7
Number of packets detected with unexpected size, or bad headers' stack
Status: current	Access: read-only
OBJECT-TYPE
	Counter32

prvtPwVcTDMPerfIntervalNearEndFC		1.3.6.1.4.1.738.1.5.200.2.1.6.1.8
Number of local packet failures.
Status: current	Access: read-only
OBJECT-TYPE
	Counter32

prvtPwVcTDMPerfIntervalFarEndFC		1.3.6.1.4.1.738.1.5.200.2.1.6.1.9
Number of remote packet failures.
Status: current	Access: read-only
OBJECT-TYPE
	Counter32

prvtPwVcTDMPerfTable		1.3.6.1.4.1.738.1.5.200.2.1.7
This table provides performance information per TDM PW similar to the prvtPwVcTDMPerfIntervalTable above. However, these counters represent complete historical information.
Status: current	Access: not-accessible
OBJECT-TYPE
	SEQUENCE OF
		PrvtPwVcTDMPerfEntry

prvtPwVcTDMPerfEntry		1.3.6.1.4.1.738.1.5.200.2.1.7.1
An entry is created in this table by the agent for every entry in the prvtPwVcTDM table.
Status: current	Access: not-accessible
OBJECT-TYPE
	PrvtPwVcTDMPerfEntry

prvtPwVcTDMPerfPktsOoseq		1.3.6.1.4.1.738.1.5.200.2.1.7.1.1
Number of packets detected out of sequence (via TDM header sequence numbers), but successfully re-ordered. Note: some implementations may not support this feature.
Status: current	Access: read-only
OBJECT-TYPE
	Counter32

prvtPwVcTDMPerfJtrBfrUnderruns		1.3.6.1.4.1.738.1.5.200.2.1.7.1.2
Number of times a packet needed to be played out and the jitter buffer was empty.
Status: current	Access: read-only
OBJECT-TYPE
	Counter32

prvtPwVcTDMPerfJtrBfrOverruns		1.3.6.1.4.1.738.1.5.200.2.1.7.1.3
Number of packets detected out of range (via TDM header sequence numbers), and could not be re- ordered, or could not fit in the jitter buffer.
Status: current	Access: read-only
OBJECT-TYPE
	Counter32

prvtPwVcTDMPerfMalformedPkt		1.3.6.1.4.1.738.1.5.200.2.1.7.1.4
Number of packets detected with unexpected size, or bad headers' stack.
Status: current	Access: read-only
OBJECT-TYPE
	Counter32

prvtPwVcTDMPerfDiscontinuityTime		1.3.6.1.4.1.738.1.5.200.2.1.7.1.5
The value of sysUpTime on the most recent occasion at which any one or more of this segment's Counter32 suffered a discontinuity. If no such discontinuities have occurred since the last re- initialization of the local management subsystem, then this object contains a zero value.
Status: current	Access: read-only
OBJECT-TYPE
	TimeStamp

prvtPwVcTDMPerfNearEndFC		1.3.6.1.4.1.738.1.5.200.2.1.7.1.6
Number of local packet failures.
Status: current	Access: read-only
OBJECT-TYPE
	Counter32

prvtPwVcTDMPerfFarEndFC		1.3.6.1.4.1.738.1.5.200.2.1.7.1.7
Number of remote packet failures.
Status: current	Access: read-only
OBJECT-TYPE
	Counter32

prvtPwVcTDMAlarmTable		1.3.6.1.4.1.738.1.5.200.2.1.8
This table contains object for configuring and displaying CES Circuits TCA thresholds.
Status: current	Access: not-accessible
OBJECT-TYPE
	SEQUENCE OF
		PrvtPwVcTDMAlarmEntry

prvtPwVcTDMAlarmEntry		1.3.6.1.4.1.738.1.5.200.2.1.8.1
Tok_String
Status: current	Access: not-accessible
OBJECT-TYPE
	PrvtPwVcTDMAlarmEntry

prvtPwVcTDMAlarmIndex		1.3.6.1.4.1.738.1.5.200.2.1.8.1.1
An integer uniquely identifying an alarm entry.
Status: current	Access: not-accessible
OBJECT-TYPE
	Gauge32

prvtPwVcTDMAlarmVariable		1.3.6.1.4.1.738.1.5.200.2.1.8.1.2
The OID of the variable whose value is being monitored. Depending on the time interval, the error condition and the modue and circuit ID, this points to an object from an entry in prvtPwVcTDMPerfCurrentTable or prvtPwVcTDMPerfTable.
Status: current	Access: read-only
OBJECT-TYPE
	OBJECT IDENTIFIER

prvtPwVcTDMAlarmThreshold		1.3.6.1.4.1.738.1.5.200.2.1.8.1.3
The alarm condition threshold for this alarm entry. The alarm is triggered if the value of the object pointed by prvtPwVcTDMAlarmVariable remains above this threshold for more than 3 seconds.
Status: current	Access: read-write
OBJECT-TYPE
	INTEGER

prvtPwVcTDMAlarmValue		1.3.6.1.4.1.738.1.5.200.2.1.8.1.4
The value of the object pointed to by prvtPwVcTDMAlarmVariable, present for notification purposes.
Status: current	Access: accessible-for-notify
OBJECT-TYPE
	INTEGER

prvtPwVcTDMAlarm		1.3.6.1.4.1.738.1.5.200.2.2.1
This notification is sent when the value of a TDM port error condition statistic has exceeded the configured threshold, or the value has dropped back below the threshold.
Status: current	Access: accessible-for-notify
NOTIFICATION-TYPE

prvtPwVcTDMStatusChange		1.3.6.1.4.1.738.1.5.200.2.2.2
This notification is sent when the operational or administrative status of circuit changes.
Status: current	Access: accessible-for-notify
NOTIFICATION-TYPE

prvtPwVcTDMGroups		1.3.6.1.4.1.738.1.5.200.2.3.1
OBJECT IDENTIFIER

prvtPwVcTDMCompliances		1.3.6.1.4.1.738.1.5.200.2.3.2
OBJECT IDENTIFIER

prvtPwTDMModuleCompliance		1.3.6.1.4.1.738.1.5.200.2.3.2.1
The compliance statement for agent that support PW over TDM PSN operation.
Status: current	Access: read-only
MODULE-COMPLIANCE

prvtPwVcTDMGroup		1.3.6.1.4.1.738.1.5.200.2.3.1.1
Collection of objects for basic TDM PW config and status.
Status: current	Access: read-only
OBJECT-GROUP

prvtPwVcTDMPerfCurrentGroup		1.3.6.1.4.1.738.1.5.200.2.3.1.2
Collection of current statistics objects for TDM PWs.
Status: current	Access: read-only
OBJECT-GROUP

prvtPwVcTDMPerfIntervalGroup		1.3.6.1.4.1.738.1.5.200.2.3.1.3
Collection of Interval statistics objects for TDM PWs.
Status: current	Access: read-only
OBJECT-GROUP

prvtPwVcTDMPerfGroup		1.3.6.1.4.1.738.1.5.200.2.3.1.4
Collection of running statistics objects for TDM PWs.
Status: current	Access: read-only
OBJECT-GROUP

prvtPwVcTDMNotificationsGroup		1.3.6.1.4.1.738.1.5.200.2.3.1.5
The group of supported notifications.
Status: current	Access: read-only
NOTIFICATION-GROUP