PROBE-MIB

File: PROBE-MIB.mib (160405 bytes)

Imported modules

RFC1155-SMI	RFC1213-MIB	RFC-1212
RMON-MIB	RFC-1215

Imported symbols

enterprises	Counter	IpAddress
TimeTicks	DisplayString	OBJECT-TYPE
EntryStatus	OwnerString	TRAP-TYPE

Defined Types

AccessLevel
INTEGER	level1(1), level2(2), level3(3), level4(4)

ControlString
DisplayString

SerialConfigEntry
SEQUENCE
	serialIfIndex	INTEGER	1..65535
	serialIpAddress	IpAddress
	serialSubnetMask	IpAddress
	serialMode	INTEGER
	serialProtocol	INTEGER
	serialSpeed	INTEGER
	serialTimeout	INTEGER	1..65535
	serialModemInitString	ControlString	Size(0..255)
	serialModemHangUpString	ControlString	Size(0..255)
	serialModemConnectResp	DisplayString	Size(0..255)
	serialModemNoConnectResp	DisplayString	Size(0..255)
	serialFlowControl	INTEGER
	serialTrapTimeout	INTEGER	1..65535

NetConfigEntry
SEQUENCE
	netConfigIfIndex	INTEGER	1..65535
	netConfigIfSpeed	INTEGER
	netConfigIPAddress	IpAddress
	netConfigSubnetMask	IpAddress
	netConfigRingNumber	INTEGER	-1..4095
	netConfigPortType	INTEGER
	netConfigDefaultGateway	IpAddress
	netConfigPhysicalConnector	INTEGER
	netConfigLinkSpeed	INTEGER
	netConfigDuplex	INTEGER
	netConfigLineCode	INTEGER
	netConfigFramingType	INTEGER
	netConfigChannelRate	INTEGER
	netConfigDataChannel	INTEGER
	netConfigDataSense	INTEGER
	netConfigLinkLayerType	INTEGER
	netConfigNetworkInterface	INTEGER
	netConfigCellSynchronization	INTEGER
	netConfigReceiverMode	INTEGER
	netConfigMaximumFrameSize	INTEGER

CommAccessEntry
SEQUENCE
	commAccessIndex	INTEGER	1..65535
	commAccessCommunity	DisplayString	Size(0..127)
	commAccessLevel	AccessLevel
	commAccessOwner	OwnerString
	commAccessStatus	EntryStatus

ClientEntry
SEQUENCE
	clientIndex	INTEGER	1..65535
	clientIpAddress	IpAddress
	clientIpMask	IpAddress
	clientCommunity	DisplayString	Size(0..127)
	clientOwner	OwnerString
	clientStatus	EntryStatus

TrapDestEntry
SEQUENCE
	trapDestIndex	INTEGER	1..65535
	trapDestCommunity	DisplayString	Size(0..127)
	trapDestDeliveryType	INTEGER
	trapDestPrimaryIpAddress	IpAddress
	trapDestPrimaryIfIndex	INTEGER	1..65535
	trapDestOwner	OwnerString
	trapDestStatus	EntryStatus

SerialConnectionEntry
SEQUENCE
	serialConnectIndex	INTEGER	1..65535
	serialConnectDestIpAddress	IpAddress
	serialConnectType	INTEGER
	serialConnectDialString	ControlString	Size(0..255)
	serialConnectSwitchConnectSeq	ControlString	Size(0..255)
	serialConnectSwitchDisconnectSeq	ControlString	Size(0..255)
	serialConnectSwitchResetSeq	ControlString	Size(0..255)
	serialConnectOwner	OwnerString
	serialConnectStatus	EntryStatus

CurrentUtilizationEntry
SEQUENCE
	curUtilIfIndex	INTEGER	1..65535
	curUtilPeriod	INTEGER
	curUtil	INTEGER
	curUtilReceive	INTEGER
	curUtilTransmit	INTEGER

HostExtEntry
SEQUENCE
	hostExtIndex	INTEGER	1..65535
	hostExtMacAddress	OCTET STRING
	hostExtNetAddrType	INTEGER
	hostExtNetAddrStatus	INTEGER
	hostExtNetAddress	OCTET STRING
	hostExtCreationOrder	INTEGER	1..65535
	hostExtLastUpdateTime	TimeTicks

HostTimeExtEntry
SEQUENCE
	hostTimeExtIndex	INTEGER	1..65535
	hostTimeExtMacAddress	OCTET STRING
	hostTimeExtNetAddrType	INTEGER
	hostTimeExtNetAddrStatus	INTEGER
	hostTimeExtNetAddress	OCTET STRING
	hostTimeExtCreationOrder	INTEGER	1..65535
	hostTimeExtLastUpdateTime	TimeTicks

ChannelExtEntry
SEQUENCE
	channelExtIndex	INTEGER	1..65535
	channelExtSelfPktCapture	INTEGER

EchoTestSSEntry
SEQUENCE
	echoTestSSIndex	INTEGER	1..65535
	echoTestSSIfIndex	INTEGER	1..65535
	echoTestSSMacAddress	OCTET STRING
	echoTestSSNetAddress	OCTET STRING
	echoTestSSProtocol	INTEGER
	echoTestSSTimeout	INTEGER
	echoTestSSRetryAttempts	INTEGER
	echoTestSSLastEchoStatus	INTEGER
	echoTestSSResponseNumber	INTEGER
	echoTestSSResponseTime	INTEGER
	echoTestSSOwner	OwnerString
	echoTestSSStatus	EntryStatus

EchoTestPeriodicEntry
SEQUENCE
	echoTestPeriodicIndex	INTEGER	1..65535
	echoTestPeriodicIfIndex	INTEGER	1..65535
	echoTestPeriodicMacAddress	OCTET STRING
	echoTestPeriodicNetAddress	OCTET STRING
	echoTestPeriodicProtocol	INTEGER
	echoTestPeriodicTimeout	INTEGER
	echoTestPeriodicRetryAttempts	INTEGER
	echoTestPeriodicNoResponseEventIndex	INTEGER
	echoTestPeriodicRespondedEventIndex	INTEGER
	echoTestPeriodicEchoState	INTEGER
	echoTestPeriodicLastEchoStatus	INTEGER
	echoTestPeriodicTotalOperations	INTEGER
	echoTestPeriodicSuccessfulOperations	INTEGER
	echoTestPeriodicMinRespTime	INTEGER
	echoTestPeriodicMaxRespTime	INTEGER
	echoTestPeriodicLastRespTime	INTEGER
	echoTestPeriodicTotalRespTime	INTEGER
	echoTestPeriodicSumOfSquaresTimeLo	INTEGER
	echoTestPeriodicSumOfSquaresTimeHi	INTEGER
	echoTestPeriodicFailedAttemptCount	INTEGER
	echoTestPeriodicMinRespTime30MinInt	INTEGER
	echoTestPeriodicMaxRespTime30MinInt	INTEGER
	echoTestPeriodicMinRespTime5MinInt	INTEGER
	echoTestPeriodicMaxRespTime5MinInt	INTEGER
	echoTestPeriodicOwner	OwnerString
	echoTestPeriodicStatus	EntryStatus

Defined Values

hp		1.3.6.1.4.1.11
OBJECT IDENTIFIER

nm		1.3.6.1.4.1.11.2
OBJECT IDENTIFIER

hpExperimental		1.3.6.1.4.1.11.2.1
OBJECT IDENTIFIER

system		1.3.6.1.4.1.11.2.3
OBJECT IDENTIFIER

interface		1.3.6.1.4.1.11.2.4
OBJECT IDENTIFIER

snmp		1.3.6.1.4.1.11.2.13
OBJECT IDENTIFIER

netElement		1.3.6.1.4.1.11.2.3.7
OBJECT IDENTIFIER

ntd		1.3.6.1.4.1.11.2.1.5
OBJECT IDENTIFIER

trap		1.3.6.1.4.1.11.2.13.1
OBJECT IDENTIFIER

community		1.3.6.1.4.1.11.2.13.5
OBJECT IDENTIFIER

lanprobe		1.3.6.1.4.1.11.2.3.7.6
OBJECT IDENTIFIER

general		1.3.6.1.4.1.11.2.3.7.6.1
OBJECT IDENTIFIER

lp1		1.3.6.1.4.1.11.2.3.7.6.2
OBJECT IDENTIFIER

lpEther		1.3.6.1.4.1.11.2.3.7.6.3
OBJECT IDENTIFIER

lp2EtherV1		1.3.6.1.4.1.11.2.3.7.6.3.1
OBJECT IDENTIFIER

lp2EtherV2		1.3.6.1.4.1.11.2.3.7.6.3.2
OBJECT IDENTIFIER

lp3Ether		1.3.6.1.4.1.11.2.3.7.6.3.3
OBJECT IDENTIFIER

pview		1.3.6.1.4.1.11.2.3.7.6.4
OBJECT IDENTIFIER

lp2TokenRing		1.3.6.1.4.1.11.2.3.7.6.5
OBJECT IDENTIFIER

lp2TokenRingV2		1.3.6.1.4.1.11.2.3.7.6.5.2
OBJECT IDENTIFIER

lpFDDI		1.3.6.1.4.1.11.2.3.7.6.6
OBJECT IDENTIFIER

lpFDDIV1		1.3.6.1.4.1.11.2.3.7.6.6.1
OBJECT IDENTIFIER

lpFDDIV2		1.3.6.1.4.1.11.2.3.7.6.6.2
OBJECT IDENTIFIER

lpQ		1.3.6.1.4.1.11.2.3.7.6.7
OBJECT IDENTIFIER

lpQuadEther		1.3.6.1.4.1.11.2.3.7.6.7.2
OBJECT IDENTIFIER

lpQuadEtherV1		1.3.6.1.4.1.11.2.3.7.6.7.2.1
OBJECT IDENTIFIER

lpFE		1.3.6.1.4.1.11.2.3.7.6.9
OBJECT IDENTIFIER

lpFastEther		1.3.6.1.4.1.11.2.3.7.6.9.1
OBJECT IDENTIFIER

lpFastEtherV1		1.3.6.1.4.1.11.2.3.7.6.9.1.1
OBJECT IDENTIFIER

lpMultiport		1.3.6.1.4.1.11.2.3.7.6.10
OBJECT IDENTIFIER

lpMultiportTokenRing		1.3.6.1.4.1.11.2.3.7.6.10.1
OBJECT IDENTIFIER

lpMultiportTokenRingV1		1.3.6.1.4.1.11.2.3.7.6.10.1.1
OBJECT IDENTIFIER

lpMultiportEther		1.3.6.1.4.1.11.2.3.7.6.10.2
OBJECT IDENTIFIER

lpMultiportEtherV1		1.3.6.1.4.1.11.2.3.7.6.10.2.1
OBJECT IDENTIFIER

lpT1		1.3.6.1.4.1.11.2.3.7.6.11
OBJECT IDENTIFIER

lpT1Multiport		1.3.6.1.4.1.11.2.3.7.6.11.1
OBJECT IDENTIFIER

lpT1MultiportV1		1.3.6.1.4.1.11.2.3.7.6.11.1.1
OBJECT IDENTIFIER

lpE1		1.3.6.1.4.1.11.2.3.7.6.12
OBJECT IDENTIFIER

lpE1Multiport		1.3.6.1.4.1.11.2.3.7.6.12.1
OBJECT IDENTIFIER

lpE1MultiportV1		1.3.6.1.4.1.11.2.3.7.6.12.1.1
OBJECT IDENTIFIER

lpVSeries		1.3.6.1.4.1.11.2.3.7.6.13
OBJECT IDENTIFIER

lpVSeriesMultiport		1.3.6.1.4.1.11.2.3.7.6.13.1
OBJECT IDENTIFIER

lpVSeriesMultiportV1		1.3.6.1.4.1.11.2.3.7.6.13.1.1
OBJECT IDENTIFIER

lpHSSerial		1.3.6.1.4.1.11.2.3.7.6.14
OBJECT IDENTIFIER

lpHSSI		1.3.6.1.4.1.11.2.3.7.6.14.1
OBJECT IDENTIFIER

lpHSSIV1		1.3.6.1.4.1.11.2.3.7.6.14.1.1
OBJECT IDENTIFIER

lpT3		1.3.6.1.4.1.11.2.3.7.6.15
OBJECT IDENTIFIER

lpT3Multiport		1.3.6.1.4.1.11.2.3.7.6.15.1
OBJECT IDENTIFIER

lpT3MultiportV1		1.3.6.1.4.1.11.2.3.7.6.15.1.1
OBJECT IDENTIFIER

lpATMUTP		1.3.6.1.4.1.11.2.3.7.6.16
OBJECT IDENTIFIER

lpATMUTPMultiport		1.3.6.1.4.1.11.2.3.7.6.16.1
OBJECT IDENTIFIER

lpATMUTPMultiportV1		1.3.6.1.4.1.11.2.3.7.6.16.1.1
OBJECT IDENTIFIER

lpATMOC3		1.3.6.1.4.1.11.2.3.7.6.17
OBJECT IDENTIFIER

lpATMOC3Multiport		1.3.6.1.4.1.11.2.3.7.6.17.1
OBJECT IDENTIFIER

lpATMOC3MultiportV1		1.3.6.1.4.1.11.2.3.7.6.17.1.1
OBJECT IDENTIFIER

lpATMT3		1.3.6.1.4.1.11.2.3.7.6.18
OBJECT IDENTIFIER

lpATMT3Multiport		1.3.6.1.4.1.11.2.3.7.6.18.1
OBJECT IDENTIFIER

lpATMT3MultiportV1		1.3.6.1.4.1.11.2.3.7.6.18.1.1
OBJECT IDENTIFIER

lpATME3		1.3.6.1.4.1.11.2.3.7.6.19
OBJECT IDENTIFIER

lpATME3Multiport		1.3.6.1.4.1.11.2.3.7.6.19.1
OBJECT IDENTIFIER

lpATME3MultiportV1		1.3.6.1.4.1.11.2.3.7.6.19.1.1
OBJECT IDENTIFIER

lpATMOC12		1.3.6.1.4.1.11.2.3.7.6.20
OBJECT IDENTIFIER

lpATMOC12Multiport		1.3.6.1.4.1.11.2.3.7.6.20.1
OBJECT IDENTIFIER

lpATMOC12MultiportV1		1.3.6.1.4.1.11.2.3.7.6.20.1.1
OBJECT IDENTIFIER

lpATMGigabit		1.3.6.1.4.1.11.2.3.7.6.21
OBJECT IDENTIFIER

lpATMGigabitMultiport		1.3.6.1.4.1.11.2.3.7.6.21.1
OBJECT IDENTIFIER

lpATMGigabitMultiportV1		1.3.6.1.4.1.11.2.3.7.6.21.1.1
OBJECT IDENTIFIER

lpE3		1.3.6.1.4.1.11.2.3.7.6.22
OBJECT IDENTIFIER

lpE3Multiport		1.3.6.1.4.1.11.2.3.7.6.22.1
OBJECT IDENTIFIER

lpE3MultiportV1		1.3.6.1.4.1.11.2.3.7.6.22.1.1
OBJECT IDENTIFIER

probeAdmin		1.3.6.1.4.1.11.2.3.7.6.1.1
OBJECT IDENTIFIER

cableTest		1.3.6.1.4.1.11.2.3.7.6.1.2
OBJECT IDENTIFIER

nodeLocation		1.3.6.1.4.1.11.2.3.7.6.1.3
OBJECT IDENTIFIER

probeView		1.3.6.1.4.1.11.2.3.7.6.1.4
OBJECT IDENTIFIER

rmonExtension		1.3.6.1.4.1.11.2.3.7.6.1.5
OBJECT IDENTIFIER

echoTest		1.3.6.1.4.1.11.2.3.7.6.1.6
OBJECT IDENTIFIER

cable		1.3.6.1.4.1.11.2.3.7.6.1.7
OBJECT IDENTIFIER

nodeLocatorII		1.3.6.1.4.1.11.2.3.7.6.1.8
OBJECT IDENTIFIER

statsExtension		1.3.6.1.4.1.11.2.3.7.6.1.5.1
OBJECT IDENTIFIER

hostsExtension		1.3.6.1.4.1.11.2.3.7.6.1.5.4
OBJECT IDENTIFIER

filterExtension		1.3.6.1.4.1.11.2.3.7.6.1.5.7
OBJECT IDENTIFIER

ethernet		1.3.6.1.4.1.11.2.4.4
OBJECT IDENTIFIER

serial		1.3.6.1.4.1.11.2.4.5
OBJECT IDENTIFIER

net		1.3.6.1.4.1.11.2.4.6
OBJECT IDENTIFIER

tokenRing		1.3.6.1.4.1.11.2.4.7
OBJECT IDENTIFIER

accessControl		1.3.6.1.4.1.11.2.13.5.1
OBJECT IDENTIFIER

delivery		1.3.6.1.4.1.11.2.13.1.3
OBJECT IDENTIFIER

slip		1.3.6.1.4.1.11.2.15
OBJECT IDENTIFIER

probeIdentification		1.3.6.1.4.1.11.2.3.7.6.1.1.1
A string uniquely identifying this device.
Status: mandatory	Access: read-write
OBJECT-TYPE
	DisplayString	Size(0..127)

probeFirmwareRev		1.3.6.1.4.1.11.2.3.7.6.1.1.2
The firmware revision of this device.
Status: mandatory	Access: read-only
OBJECT-TYPE
	DisplayString	Size(0..32)

probeHardwareRev		1.3.6.1.4.1.11.2.3.7.6.1.1.3
The hardware revision of this device.
Status: mandatory	Access: read-only
OBJECT-TYPE
	DisplayString	Size(0..31)

probeDateTime		1.3.6.1.4.1.11.2.3.7.6.1.1.4
Probe's current date and time in the format: WWW MMM DD HH:MM:SS TTT YYYY (eg: 'Wed Jan 02 02:03:55 PST 1980'). The length of the timezone field can be from 1 to 15 octets. The timezone is stored for the convenience of the manager and is not used by the probe to adjust the probe's clock. If and when the timezone and clock changes, the manager must update probeDateTime. The timezone field has the default value of 'PST', Pacific Standard Time.
Status: mandatory	Access: read-write
OBJECT-TYPE
	DisplayString	Size(26..40)

probeResetControl		1.3.6.1.4.1.11.2.3.7.6.1.1.5
Setting this object to warmBoot(2) causes the device to restart the application software with current configuration parameters saved in non-volatile memory. Setting this object to coldBoot(3) causes the device to reinitialize configuration parameters in non-volatile memory to default values and restart the application software. When the device is running normally, this variable has a value of running(1).
Status: mandatory	Access: read-write
OBJECT-TYPE
	INTEGER	running(1), warmBoot(2), coldBoot(3)

probeDownloadFile		1.3.6.1.4.1.11.2.3.7.6.1.1.6
The file name to be downloaded from the TFTP server.
Status: mandatory	Access: read-write
OBJECT-TYPE
	DisplayString	Size(0..127)

probeDownloadTFTPServer		1.3.6.1.4.1.11.2.3.7.6.1.1.7
The IP address of the TFTP server that contains the boot image to load.
Status: mandatory	Access: read-write
OBJECT-TYPE
	IpAddress

probeDownloadAction		1.3.6.1.4.1.11.2.3.7.6.1.1.8
When this object is set to downloadToRAM(2) or downloadToPROM(3), the device will discontinue its normal operation and begin download of the image specified by probeDownLoadFile from the server specifed by probeDownLoadTFTPServer using the TFTP protocol. If downloadToRAM(2) is specified, the new image is copied to RAM only (the old image remains unaltered in the flash EPROM). If downloadToPROM(3) is specified (supported only by LanProbe-II), the new image is written to the flash EPROM memory after its checksum has been verified to be correct. When the download process is completed, the device will warm boot to restart the newly loaded application. When the device is not downloading, this object will have a value of imageValid(1).
Status: mandatory	Access: read-write
OBJECT-TYPE
	INTEGER	imageValid(1), downloadToPROM(2), downloadToRAM(3)

probeDownloadStatus		1.3.6.1.4.1.11.2.3.7.6.1.1.9
The status of the last download procedure, if any. This object will have a value of downloadStatusUnknown(3) if no download process has been performed.
Status: mandatory	Access: read-only
OBJECT-TYPE
	INTEGER	downloadSuccess(1), downloadFailed(2), downloadStatusUnknown(3)

probeEchoInterval		1.3.6.1.4.1.11.2.3.7.6.1.1.10
The probe will send an ICMP echo request (ping) to the default gateway every probeEchoInterval seconds. To force the probe not to send any echo requests, set probeEchoInterval to 0.
Status: mandatory	Access: read-write
OBJECT-TYPE
	INTEGER

probeFeatureDeactivate		1.3.6.1.4.1.11.2.3.7.6.1.1.12
This integer represents ORed bit fields which can be set to deactivate certain features of a probe. Currently defined bit fields: Bit Feature To Deactivate --- --------------------- 0 Packet Capture 1 TFTP Firmware Download 2 Packet generation capability 3 Duplicate IP/changed IP processing
Status: mandatory	Access: read-only
OBJECT-TYPE
	INTEGER

serialConfigTable		1.3.6.1.4.1.11.2.4.5.1
A table of Serial interface configuration entries.
Status: mandatory	Access: not-accessible
OBJECT-TYPE
	SEQUENCE OF
		SerialConfigEntry

serialConfigEntry		1.3.6.1.4.1.11.2.4.5.1.1
A set of configuration parameters for a particular serial interface on this device.
Status: mandatory	Access: not-accessible
OBJECT-TYPE
	SerialConfigEntry

serialIfIndex		1.3.6.1.4.1.11.2.4.5.1.1.1
The value of this object uniquely identifies the serial interface on this device for which this entry contains configuration parameters. The interface identified by a particular value of this object is the same interface as identified by the same value of the ifIndex object, defined in RFC 1213.
Status: mandatory	Access: read-only
OBJECT-TYPE
	INTEGER	1..65535

serialIpAddress		1.3.6.1.4.1.11.2.4.5.1.1.2
The IP address of this serial interface.
Status: mandatory	Access: read-write
OBJECT-TYPE
	IpAddress

serialSubnetMask		1.3.6.1.4.1.11.2.4.5.1.1.3
The IP subnet mask of this serial interface.
Status: mandatory	Access: read-write
OBJECT-TYPE
	IpAddress

serialMode		1.3.6.1.4.1.11.2.4.5.1.1.4
The type of incoming connection to expect on this serial interface.
Status: mandatory	Access: read-write
OBJECT-TYPE
	INTEGER	direct(1), modem(2)

serialProtocol		1.3.6.1.4.1.11.2.4.5.1.1.5
The type of data link encapsulation to be used on this serial interface.
Status: mandatory	Access: read-write
OBJECT-TYPE
	INTEGER	slip(1)

serialSpeed		1.3.6.1.4.1.11.2.4.5.1.1.6
The data rate to configure this serial interface to on startup as well as after each serial connection.
Status: mandatory	Access: read-write
OBJECT-TYPE
	INTEGER	speed-300bps(1), speed-1200bps(2), speed-2400bps(3), speed-4800bps(4), speed-9600bps(5), speed-14400bps(6), speed-19200bps(7), speed-38400bps(8)

serialTimeout		1.3.6.1.4.1.11.2.4.5.1.1.7
This timeout value is used when the Management Station has initiated the conversation over the serial link. This variable represents the number of seconds of inactivity allowed before terminating the connection on this serial interface. Use the serialTrapTimeout in the case where the probe has initiated the connection for the purpose of sending a trap.
Status: mandatory	Access: read-write
OBJECT-TYPE
	INTEGER	1..65535

serialModemInitString		1.3.6.1.4.1.11.2.4.5.1.1.8
A control string which controls how a modem attached to this serial interface should be initialized. The initialization is performed once during startup and again after each connection is terminated if the associated serialMode has the value of modem(2).
Status: mandatory	Access: read-write
OBJECT-TYPE
	ControlString	Size(0..255)

serialModemHangUpString		1.3.6.1.4.1.11.2.4.5.1.1.9
A control string which specifies how to disconnect a modem connection on this serial interface. This object is only meaningful if the associated serialMode has the value of modem(2).
Status: mandatory	Access: read-write
OBJECT-TYPE
	ControlString	Size(0..255)

serialModemConnectResp		1.3.6.1.4.1.11.2.4.5.1.1.10
An ASCII string conntaining substrings that desribe the expected modem connection response code and associated bps rate. The substrings are delimited by the first character in the string, for example: /CONNECT/300/CONNECT 1200/1200/CONNECT 2400/2400/ CONNECT 4800/4800/CONNECT 9600/9600 will be interpreted as: response code bps rate CONNECT 300 CONNECT 1200 1200 CONNECT 2400 2400 CONNECT 4800 4800 CONNECT 9600 9600 The agent will use the information in this string to adjust the bps rate of this serial interface once a modem connection is established.
Status: mandatory	Access: read-write
OBJECT-TYPE
	DisplayString	Size(0..255)

serialModemNoConnectResp		1.3.6.1.4.1.11.2.4.5.1.1.11
An ASCII string containing response codes that may be generated by a modem to report the reason why a connection attempt has failed. The response codes are delimited by the first character in the string, for example: /NO CARRIER/BUSY/NO DIALTONE/NO ANSWER/ERROR/ If one of these response codes is received via this serial interface while attempting to make a modem connection, the agent will issue the hang up command as specified by modemHangUpString.
Status: mandatory	Access: read-write
OBJECT-TYPE
	DisplayString	Size(0..255)

serialFlowControl		1.3.6.1.4.1.11.2.4.5.1.1.12
The type of flow control to use on this serial interface.
Status: mandatory	Access: read-write
OBJECT-TYPE
	INTEGER	noFlowControl(1), hardwareFlowControl(2)

serialTrapTimeout		1.3.6.1.4.1.11.2.4.5.1.1.13
This timeout value is used when the probe initiates the serial connection with the intention of sending a trap. This variable represents the number of seconds of inactivity allowed before terminating the connection on this serial interface.
Status: mandatory	Access: read-write
OBJECT-TYPE
	INTEGER	1..65535

netConfigTable		1.3.6.1.4.1.11.2.4.6.1
A table of network configuration entries.
Status: mandatory	Access: not-accessible
OBJECT-TYPE
	SEQUENCE OF
		NetConfigEntry

netConfigEntry		1.3.6.1.4.1.11.2.4.6.1.1
A set of configuration parameters for a particular network interface on this device.
Status: mandatory	Access: not-accessible
OBJECT-TYPE
	NetConfigEntry

netConfigIfIndex		1.3.6.1.4.1.11.2.4.6.1.1.1
The value of this object uniquely identifies the physical interface on this device for which this entry contains configuration parameters. The interface identified by a particular value of this object is the same interface as identified by the same value of the ifIndex object, defined in RFC 1213.
Status: mandatory	Access: read-only
OBJECT-TYPE
	INTEGER	1..65535

netConfigIfSpeed		1.3.6.1.4.1.11.2.4.6.1.1.2
The value of this object indicates the speed of the media. This is equivalent to the MIB-2 object ifSpeed.
Status: mandatory	Access: read-only
OBJECT-TYPE
	INTEGER	ifsp-1Mb(1), ifsp-10Mb(2), ifsp-100Mb(3), ifsp-4Mb(4), ifsp-16Mb(5), ifsp-unspecified(6), ifsp-20Mb(7), ifsp-200Mb(8), ifsp-1Gb(9), ifsp-64000bps(10), ifsp-128000bps(11), ifsp-192000bps(12), ifsp-256000bps(13), ifsp-320000bps(14), ifsp-384000bps(15), ifsp-448000bps(16), ifsp-512000bps(17), ifsp-576000bps(18), ifsp-640000bps(19), ifsp-704000bps(20), ifsp-768000bps(21), ifsp-832000bps(22), ifsp-896000bps(23), ifsp-960000bps(24), ifsp-1024000bps(25), ifsp-1088000bps(26), ifsp-1152000bps(27), ifsp-1216000bps(28), ifsp-1280000bps(29), ifsp-1344000bps(30), ifsp-1408000bps(31), ifsp-1472000bps(32), ifsp-1536000bps(33), ifsp-1600000bps(34), ifsp-1664000bps(35), ifsp-1728000bps(36), ifsp-1792000bps(37), ifsp-1856000bps(38), ifsp-1920000bps(39), ifsp-1984000bps(40), ifsp-56000bps(41), ifsp-112000bps(42), ifsp-168000bps(43), ifsp-224000bps(44), ifsp-280000bps(45), ifsp-336000bps(46), ifsp-392000bps(47), ifsp-504000bps(48), ifsp-560000bps(49), ifsp-616000bps(50), ifsp-672000bps(51), ifsp-728000bps(52), ifsp-784000bps(53), ifsp-840000bps(54), ifsp-952000bps(55), ifsp-1008000bps(56), ifsp-1064000bps(57), ifsp-1120000bps(58), ifsp-1176000bps(59), ifsp-1232000bps(60), ifsp-1288000bps(61), ifsp-300bps(62), ifsp-1200bps(63), ifsp-2400bps(64), ifsp-4800bps(65), ifsp-7200bps(66), ifsp-9600bps(67), ifsp-12000bps(68), ifsp-14400bps(69), ifsp-19200bps(70), ifsp-38400bps(71), ifsp-57600bps(72), ifsp-115200bps(73), ifsp-34368kbps(74), ifsp-44736kbps(75), ifsp-155520kbps(76), ifsp-622000kbps(77), ifsp-2048000bps(78), ifsp-1000kbps(79), ifsp-1500kbps(80), ifsp-2000kbps(81), ifsp-2500kbps(82), ifsp-3000kbps(83), ifsp-3500kbps(84), ifsp-4000kbps(85), ifsp-4500kbps(86), ifsp-5000kbps(87), ifsp-5500kbps(88), ifsp-6000kbps(89), ifsp-6500kbps(90), ifsp-7000kbps(91), ifsp-7500kbps(92), ifsp-8000kbps(93), ifsp-8500kbps(94), ifsp-9000kbps(95), ifsp-9500kbps(96), ifsp-10000kbps(97), ifsp-10500kbps(98), ifsp-11000kbps(99), ifsp-11500kbps(100), ifsp-12000kbps(101), ifsp-12500kbps(102), ifsp-13000kbps(103), ifsp-13500kbps(104), ifsp-14000kbps(105), ifsp-14500kbps(106), ifsp-15000kbps(107), ifsp-15500kbps(108), ifsp-16000kbps(109), ifsp-16500kbps(110), ifsp-17000kbps(111), ifsp-17500kbps(112), ifsp-18000kbps(113), ifsp-18500kbps(114), ifsp-19000kbps(115), ifsp-19500kbps(116), ifsp-20000kbps(117), ifsp-20500kbps(118), ifsp-21000kbps(119), ifsp-21500kbps(120), ifsp-22000kbps(121), ifsp-22500kbps(122), ifsp-23000kbps(123), ifsp-23500kbps(124), ifsp-24000kbps(125), ifsp-24500kbps(126), ifsp-25000kbps(127), ifsp-25500kbps(128), ifsp-26000kbps(129), ifsp-26500kbps(130), ifsp-27000kbps(131), ifsp-27500kbps(132), ifsp-28000kbps(133), ifsp-28500kbps(134), ifsp-29000kbps(135), ifsp-29500kbps(136), ifsp-30000kbps(137), ifsp-30500kbps(138), ifsp-31000kbps(139), ifsp-31500kbps(140), ifsp-32000kbps(141), ifsp-32500kbps(142), ifsp-33000kbps(143), ifsp-33500kbps(144), ifsp-34000kbps(145), ifsp-34100kbps(146), ifsp-34500kbps(147), ifsp-35000kbps(148), ifsp-35500kbps(149), ifsp-36000kbps(150), ifsp-36500kbps(151), ifsp-37000kbps(152), ifsp-37500kbps(153), ifsp-38000kbps(154), ifsp-38500kbps(155), ifsp-39000kbps(156), ifsp-39500kbps(157), ifsp-40000kbps(158), ifsp-40500kbps(159), ifsp-41000kbps(160), ifsp-41500kbps(161), ifsp-42000kbps(162), ifsp-42500kbps(163), ifsp-43000kbps(164), ifsp-43500kbps(165), ifsp-44000kbps(166), ifsp-44210kbps(167), ifsp-44500kbps(168), ifsp-45000kbps(169), ifsp-45500kbps(170), ifsp-46000kbps(171), ifsp-46500kbps(172), ifsp-47000kbps(173), ifsp-47500kbps(174), ifsp-48000kbps(175), ifsp-48500kbps(176), ifsp-49000kbps(177), ifsp-49500kbps(178), ifsp-50000kbps(179), ifsp-50500kbps(180), ifsp-51000kbps(181), ifsp-51500kbps(182), ifsp-52000kbps(183)

netConfigIPAddress		1.3.6.1.4.1.11.2.4.6.1.1.3
The IP address of this Net interface. The default value for this object is 0.0.0.0. If either the netConfigIPAddress or netConfigSubnetMask are 0.0.0.0, then when the device boots, it will use BOOTP to try to figure out what these values should be. Otherwise, if BOOTP fails, before the device can talk on the network, this value must be configured through a terminal attached to the device.
Status: mandatory	Access: read-write
OBJECT-TYPE
	IpAddress

netConfigSubnetMask		1.3.6.1.4.1.11.2.4.6.1.1.4
The subnet mask of this Net interface. The default value for this object is 0.0.0.0. If either the netConfigIPAddress or netConfigSubnetMask are 0.0.0.0, then when the device boots, it will use BOOTP to try to figure out what these values should be. Otherwise, if BOOTP fails, before the device can talk on the network, this value must be configured through a terminal attached to the device.
Status: mandatory	Access: read-write
OBJECT-TYPE
	IpAddress

netConfigRingNumber		1.3.6.1.4.1.11.2.4.6.1.1.5
The value of this object uniquely identifies the physical ring number on which the probe resides. This variable is only meaningful on a Token Ring probe. If the user sets this value to -1, the probe will attempt to 'auto-discover' the ring number by sending a packet to the Ring Parameter Server. Setting this variable to any value other than -1 indicates that the user wants to explicitly set the ring number to the given value. This value will take effect the next time the probe is rebooted, or the next time a sourceRoutingTable entry is created.
Status: mandatory	Access: read-write
OBJECT-TYPE
	INTEGER	-1..4095

netConfigPortType		1.3.6.1.4.1.11.2.4.6.1.1.6
This object indicates whether or not the port for this row (indicated in netConfigIfIndex) is monitor only or can transmit as well. If this port is monitorOnly the values of netConfigIpAddress and netConfigSubnetMask for this row are in reality don't cares.
Status: mandatory	Access: read-write
OBJECT-TYPE
	INTEGER	monitorOnly(1), telemetry(2), monitorTransmit(3)

netConfigDefaultGateway		1.3.6.1.4.1.11.2.4.6.1.1.7
The IP Address of the default gateway for this Net interface.
Status: mandatory	Access: read-write
OBJECT-TYPE
	IpAddress

netConfigPhysicalConnector		1.3.6.1.4.1.11.2.4.6.1.1.8
The value of this object indicates the type of physical connector which is currently being used to connect the interface to the network.
Status: mandatory	Access: read-write
OBJECT-TYPE
	INTEGER	rj-45(1), aui(2), fiber(3), bnc(4), db-9(5), db-25(6), mini-bantam(7), rj-48c(8), db-37(9), br-2(10), hssi(11), unknown(12)

netConfigLinkSpeed		1.3.6.1.4.1.11.2.4.6.1.1.9
Indicates the speed of the media (in one direction). For Fast Ethernet auto-negotiation and Token-Ring speed auto-detection, this value should be set to auto-negotiate. For Token-Ring, the default value should be 16Mb. For Fast Ethernet, the default value should be auto-negotiate. For V-Series WAN, the speed must be selected for the interface. For ATM, the speed can be determined by the interface card type. For T1 and E1, the speed should be calculated from the data channels and channel speed.
Status: mandatory	Access: read-write
OBJECT-TYPE
	INTEGER	lksp-1Mb(1), lksp-10Mb(2), lksp-100Mb(3), lksp-4Mb(4), lksp-16Mb(5), lksp-auto-negotiate(6), lksp-20Mb(7), lksp-200Mb(8), lksp-1Gb(9), lksp-64000bps(10), lksp-128000bps(11), lksp-192000bps(12), lksp-256000bps(13), lksp-320000bps(14), lksp-384000bps(15), lksp-448000bps(16), lksp-512000bps(17), lksp-576000bps(18), lksp-640000bps(19), lksp-704000bps(20), lksp-768000bps(21), lksp-832000bps(22), lksp-896000bps(23), lksp-960000bps(24), lksp-1024000bps(25), lksp-1088000bps(26), lksp-1152000bps(27), lksp-1216000bps(28), lksp-1280000bps(29), lksp-1344000bps(30), lksp-1408000bps(31), lksp-1472000bps(32), lksp-1536000bps(33), lksp-1600000bps(34), lksp-1664000bps(35), lksp-1728000bps(36), lksp-1792000bps(37), lksp-1856000bps(38), lksp-1920000bps(39), lksp-1984000bps(40), lksp-56000bps(41), lksp-112000bps(42), lksp-168000bps(43), lksp-224000bps(44), lksp-280000bps(45), lksp-336000bps(46), lksp-392000bps(47), lksp-504000bps(48), lksp-560000bps(49), lksp-616000bps(50), lksp-672000bps(51), lksp-728000bps(52), lksp-784000bps(53), lksp-840000bps(54), lksp-952000bps(55), lksp-1008000bps(56), lksp-1064000bps(57), lksp-1120000bps(58), lksp-1176000bps(59), lksp-1232000bps(60), lksp-1288000bps(61), lksp-300bps(62), lksp-1200bps(63), lksp-2400bps(64), lksp-4800bps(65), lksp-7200bps(66), lksp-9600bps(67), lksp-12000bps(68), lksp-14400bps(69), lksp-19200bps(70), lksp-38400bps(71), lksp-57600bps(72), lksp-115200bps(73), lksp-34368kbps(74), lksp-44736kbps(75), lksp-155520kbps(76), lksp-622000kbps(77), lksp-2048000bps(78), lksp-1000kbps(79), lksp-1500kbps(80), lksp-2000kbps(81), lksp-2500kbps(82), lksp-3000kbps(83), lksp-3500kbps(84), lksp-4000kbps(85), lksp-4500kbps(86), lksp-5000kbps(87), lksp-5500kbps(88), lksp-6000kbps(89), lksp-6500kbps(90), lksp-7000kbps(91), lksp-7500kbps(92), lksp-8000kbps(93), lksp-8500kbps(94), lksp-9000kbps(95), lksp-9500kbps(96), lksp-10000kbps(97), lksp-10500kbps(98), lksp-11000kbps(99), lksp-11500kbps(100), lksp-12000kbps(101), lksp-12500kbps(102), lksp-13000kbps(103), lksp-13500kbps(104), lksp-14000kbps(105), lksp-14500kbps(106), lksp-15000kbps(107), lksp-15500kbps(108), lksp-16000kbps(109), lksp-16500kbps(110), lksp-17000kbps(111), lksp-17500kbps(112), lksp-18000kbps(113), lksp-18500kbps(114), lksp-19000kbps(115), lksp-19500kbps(116), lksp-20000kbps(117), lksp-20500kbps(118), lksp-21000kbps(119), lksp-21500kbps(120), lksp-22000kbps(121), lksp-22500kbps(122), lksp-23000kbps(123), lksp-23500kbps(124), lksp-24000kbps(125), lksp-24500kbps(126), lksp-25000kbps(127), lksp-25500kbps(128), lksp-26000kbps(129), lksp-26500kbps(130), lksp-27000kbps(131), lksp-27500kbps(132), lksp-28000kbps(133), lksp-28500kbps(134), lksp-29000kbps(135), lksp-29500kbps(136), lksp-30000kbps(137), lksp-30500kbps(138), lksp-31000kbps(139), lksp-31500kbps(140), lksp-32000kbps(141), lksp-32500kbps(142), lksp-33000kbps(143), lksp-33500kbps(144), lksp-34000kbps(145), lksp-34100kbps(146), lksp-34500kbps(147), lksp-35000kbps(148), lksp-35500kbps(149), lksp-36000kbps(150), lksp-36500kbps(151), lksp-37000kbps(152), lksp-37500kbps(153), lksp-38000kbps(154), lksp-38500kbps(155), lksp-39000kbps(156), lksp-39500kbps(157), lksp-40000kbps(158), lksp-40500kbps(159), lksp-41000kbps(160), lksp-41500kbps(161), lksp-42000kbps(162), lksp-42500kbps(163), lksp-43000kbps(164), lksp-43500kbps(165), lksp-44000kbps(166), lksp-44210kbps(167), lksp-44500kbps(168), lksp-45000kbps(169), lksp-45500kbps(170), lksp-46000kbps(171), lksp-46500kbps(172), lksp-47000kbps(173), lksp-47500kbps(174), lksp-48000kbps(175), lksp-48500kbps(176), lksp-49000kbps(177), lksp-49500kbps(178), lksp-50000kbps(179), lksp-50500kbps(180), lksp-51000kbps(181), lksp-51500kbps(182), lksp-52000kbps(183)

netConfigDuplex		1.3.6.1.4.1.11.2.4.6.1.1.10
Indicates whether the interface supports half or full duplex mode. When LinkSpeed is set to auto-negotiate, this field has no effect. It will be set to the negotiated mode.
Status: mandatory	Access: read-write
OBJECT-TYPE
	INTEGER	half-duplex(1), full-duplex(2)

netConfigLineCode		1.3.6.1.4.1.11.2.4.6.1.1.11
Line coding. The choices for this field are: B8ZS - Binary 8 Zeros Suppress. Used with more recent ESF T1 framing. Commonly used in 64 Kbps, fractional T1 and Primary Rate ISDN lines. Valid for T1. AMI - Alternate Mark Inversion. Usually the choice with D4 framing. Common in existing 56 Kbps DDS type circuits. Valid for T1 and E1. HDB3 - High Density Bipolar, 3 zeros. Valid for E1 and E3. B3ZS - Binary 3 Zeros Suppress. Valid for T3. This field applies only to the T1, E1 and T3/DS-3 WanProbes.
Status: mandatory	Access: read-write
OBJECT-TYPE
	INTEGER	b8zs(1), ami(2), hdb3(3), b3zs(4)

netConfigFramingType		1.3.6.1.4.1.11.2.4.6.1.1.12
Framing type. The choices for this field are: ESF - Extended Super Frame (24 frames/ESF). Valid for T1. D4 - Conventional Super Frame (12 frames/SF). Valid for T1. with CRC-4 - Cyclic Redundancy Check, 4 bits. Valid for E1. without CRC-4 - CRC not checked. Valid for E1. M13 - A DS-3 framing fromat. See C-Bit parity. Valid for T3. C-Bit Parity - The synchronous DS-3 C-Bit Parity is a structure that can be used to multiplex 28 DS-1 signals to the DS-3 signal level. In C-Bit Parity, the X-Bit channel is used to transmit failure conditions from the far end to the near end of a system. Valid for T3. G.832/G.804 - Valid with PLCP cell synchronization only. Valid for ATM E3. G.751 - Valid with HEC cell synchronization only. Valid for ATM E3. T1DM (DDS) - A.T&T. DDS Framing using D4 and time slot 24. Not Implemented at this time. SLIC-96 - Special version of D4 framing. Useds 4-D4 frames but changes some of the framing bits. Not Implemented at this time. This field applies only to the T1, E1, T3/DS-3 WanProbes and DS-3 and E3 ATMProbes.
Status: mandatory	Access: read-write
OBJECT-TYPE
	INTEGER	esf(1), d4(2), withCRC4(3), withoutCRC4(4), m13(5), cbitParity(6), g804(7), g751(8), t1dm(9), slic96(10)

netConfigChannelRate		1.3.6.1.4.1.11.2.4.6.1.1.13
Channel Rate. The choices for this field are: 56K - Valid for T1. 64K - Valid for T1/E1. 1536bps - Valid for Channelized T3. This field applies only to the T1, E1 and T3/DS-3 WanProbes.
Status: mandatory	Access: read-write
OBJECT-TYPE
	INTEGER	chnrt-56K(1), chnrt-64K(2), chnrt-1536000bps(3)

netConfigDataChannel		1.3.6.1.4.1.11.2.4.6.1.1.14
This integer represents the ORed bit fields which can be set to indicate that the probe should monitor the specified channel on the incoming data line. A value of 1 in the bit position indicates that the channel is to be monitored. Channel 1 is in the least significant bit position. T1: 1 - 24 data channels. E1: 1 - 31 data channels. T3: 1 - 28 data channels. This field applies only to the T1, E1 and T3/DS-3 WanProbes.
Status: mandatory	Access: read-write
OBJECT-TYPE
	INTEGER

netConfigDataSense		1.3.6.1.4.1.11.2.4.6.1.1.15
Indicates whether the bits on the channel(s) being tested are inverted. A Mark is a signal pulse on the line. A Space is a bit time with no pulse. The choices for this field are: Normal - Indicates that the bits are not inverted; therefore a Mark is represented by a binary 1. Inverted - A Mark is represented by a binary 0. NRZI - Non-Return to Zero Invert (on zeros), bit timing follows derived line timing. Successive Marks or Spaces represent binary 1. Changes from Mark to Space or from Space to Mark represent a binary 0. This field applies only to the T1, E1, V-Series, T3/DS-3 WanProbes.
Status: mandatory	Access: read-write
OBJECT-TYPE
	INTEGER	normal(1), inverted(2), nrzi(3)

netConfigLinkLayerType		1.3.6.1.4.1.11.2.4.6.1.1.16
Indicates the type of link layer analysis to be performed on the incoming data. This field applies only to WanProbes and ATMProbes
Status: mandatory	Access: read-write
OBJECT-TYPE
	INTEGER	frameRelay(1), x25(2), hdlc(3), sdlc(4), aal5(5), ppp(6)

netConfigNetworkInterface		1.3.6.1.4.1.11.2.4.6.1.1.17
ATM network interface addressing mode. Valid values for this field are: NNI - Network to Network Interface. The Network to Network Interface (or Network to Node Interface) is similar to UNI but these is no 4-bit GFC field. The 4 extra bits are used as part of the VPI. UNI - User Network Interface. This field applies only to ATMProbes
Status: mandatory	Access: read-write
OBJECT-TYPE
	INTEGER	uni(1), nni(2)

netConfigCellSynchronization		1.3.6.1.4.1.11.2.4.6.1.1.18
ATM network interface addressing mode. Valid values for this field are: HEC - The Header Error Control (DEC) is an 8-bit field and the fifth byte in the header of an ATM cell. The HEC value is calculated from the first four bytes of the cell header. If an error occurs in an ATM cell header, it will be detected in the HEC field. Cells with HEC errors that can not be corrected are discarded by the receiving node. The HEC field can also be used to determine the boundaries of a packet for cell delineation. Valid for ATM OC-3, ATM UTP, ATM T3, ATM E3 with G.832/G.804 framing. PLCP - Physical Layer Convergence Protocol. Each cell is preceded by a 2-byte framing pattern (A1, A2) to enable the receiver to synchronize to the cells. Valid for ATM OC-3, ATM UTP, ATM T3, ATM E3 with G.751 framing. This field applies only to ATMProbes
Status: mandatory	Access: read-write
OBJECT-TYPE
	INTEGER	hec(1), plcp(2)

netConfigReceiverMode		1.3.6.1.4.1.11.2.4.6.1.1.19
Line: When monitoring, the selected challes are presented as the line and equipment signals for decoding and statistics. All changes are regenerated and passed through unaltered. Monitor_jack: Expect the lower amplitude, isolated T1 test point signal (increased receiver gain). Expect the higher ampliture E1 test point signal (-20dB) This field applies only to the T1, E1 and T3/DS-3 WanProbes.
Status: mandatory	Access: read-write
OBJECT-TYPE
	INTEGER	line(1), monitor-jack(2)

netConfigMaximumFrameSize		1.3.6.1.4.1.11.2.4.6.1.1.20
The size of the buffer to be allocated at the physical layer for the reception of a frame from the network. Any frames which are longer than the maximum frame size will be reported as a errored frame. The number of buffers available to receive frames is (POOL SIZE / maximum frame size). Overallocation of this maximum frame size decreases the number of available buffers which could result in dropped frames during periods of heavy network utilization. The minimum accepted value is 1024. The maximum accepted value is 65535.
Status: mandatory	Access: read-write
OBJECT-TYPE
	INTEGER

netDefaultGateway		1.3.6.1.4.1.11.2.4.6.2
NOTE: Because, this variable has been obsoleted by the variable netConfigDefaultGateway, it will be deprecated in a future firmware release. Applications should migrate to the new MIB variable as soon as possible. The IP Address of the default gateway. This entry should be equal to the value of netConfigDefaultGateway.1 for multi-port probes.
Status: mandatory	Access: read-write
OBJECT-TYPE
	IpAddress

tokenRingSpeed		1.3.6.1.4.1.11.2.4.7.1
NOTE: Because, this variable has been obsoleted by the netConfigLinkSpeed and netConfigIfSpeed, it will be deprecated in a future firmware release. Applications should migrate to the new MIB variables as soon as possible. This object specifies the speed of the token ring that is being connected to. If autoDetect(1) is selected, the correct value will be filled in in this object by the hardware after some ammount of time. This variable does not apply to Token-Ring interfaces on a multi-interface probe. Refer to netConfigLinkSpeed and netConfigIfSpeed in the netConfigTable.
Status: mandatory	Access: read-write
OBJECT-TYPE
	INTEGER	autoDetect(1), ringsp-4Mbps(2), ringsp-16Mbps(3)

commAccessTable		1.3.6.1.4.1.11.2.13.5.1.1
A list of community access entries
Status: mandatory	Access: not-accessible
OBJECT-TYPE
	SEQUENCE OF
		CommAccessEntry

commAccessEntry		1.3.6.1.4.1.11.2.13.5.1.1.1
A mapping of community name to access rights.
Status: mandatory	Access: not-accessible
OBJECT-TYPE
	CommAccessEntry

commAccessIndex		1.3.6.1.4.1.11.2.13.5.1.1.1.1
A unique index for this entry.
Status: mandatory	Access: read-only
OBJECT-TYPE
	INTEGER	1..65535

commAccessCommunity		1.3.6.1.4.1.11.2.13.5.1.1.1.2
The community string to which this entry grants access. This string must be unique among the community strings defined in all entries of this table. This object may not be modifed if the associated commAccessStatus object is equal to valid(1).
Status: mandatory	Access: read-write
OBJECT-TYPE
	DisplayString	Size(0..127)

commAccessLevel		1.3.6.1.4.1.11.2.13.5.1.1.1.3
The access level for this community string. This object may not be modifed if the associated commAccessStatus object is equal to valid(1).
Status: mandatory	Access: read-write
OBJECT-TYPE
	AccessLevel

commAccessOwner		1.3.6.1.4.1.11.2.13.5.1.1.1.4
The owner of this serial connection entry.
Status: mandatory	Access: read-write
OBJECT-TYPE
	OwnerString

commAccessStatus		1.3.6.1.4.1.11.2.13.5.1.1.1.5
The status of this community access entry. When this object is set to valid(1), if the commAccessCommunity for this row is not unique among commAccessCommunity objects for all valid rows, the set request will be rejected with badValue(3).
Status: mandatory	Access: read-write
OBJECT-TYPE
	EntryStatus

clientTable		1.3.6.1.4.1.11.2.13.5.1.2
A list of client entries.
Status: mandatory	Access: not-accessible
OBJECT-TYPE
	SEQUENCE OF
		ClientEntry

clientEntry		1.3.6.1.4.1.11.2.13.5.1.2.1
A configuration that allows an SNMP community to send packets from a particular IP address.
Status: mandatory	Access: not-accessible
OBJECT-TYPE
	ClientEntry

clientIndex		1.3.6.1.4.1.11.2.13.5.1.2.1.1
A value that uniquely identifies this client entry.
Status: mandatory	Access: read-only
OBJECT-TYPE
	INTEGER	1..65535

clientIpAddress		1.3.6.1.4.1.11.2.13.5.1.2.1.2
An IP Address (or portion thereof) from which this device will accept SNMP packets with the associated community. The requesting entity's IP address is ANDed with the clientIpMask before being compared to the clientIpAddress. Note that if the clientIpMask is set to 0.0.0.0, a clientIpAddress of 0.0.0.0 matches all IP addresses. This object may not be modifed if the associated clientStatus object is equal to valid(1).
Status: mandatory	Access: read-write
OBJECT-TYPE
	IpAddress

clientIpMask		1.3.6.1.4.1.11.2.13.5.1.2.1.3
A mask to be ANDed with the requesting entity's IP address before comparison with clientIpAddress. If the result matches with clientIpAddress, then the address is authenticated. This object may not be modifed if the associated clientStatus object is equal to valid(1).
Status: mandatory	Access: read-write
OBJECT-TYPE
	IpAddress

clientCommunity		1.3.6.1.4.1.11.2.13.5.1.2.1.4
The community that can be used by the client represented by the associated IP Address. This object may not be modifed if the associated clientStatus object is equal to valid(1).
Status: mandatory	Access: read-write
OBJECT-TYPE
	DisplayString	Size(0..127)

clientOwner		1.3.6.1.4.1.11.2.13.5.1.2.1.5
The owner of this client entry.
Status: mandatory	Access: read-write
OBJECT-TYPE
	OwnerString

clientStatus		1.3.6.1.4.1.11.2.13.5.1.2.1.6
The status of this client entry.
Status: mandatory	Access: read-write
OBJECT-TYPE
	EntryStatus

trapDestTable		1.3.6.1.4.1.11.2.13.1.3.3
A list of trap destination entries.
Status: mandatory	Access: not-accessible
OBJECT-TYPE
	SEQUENCE OF
		TrapDestEntry

trapDestEntry		1.3.6.1.4.1.11.2.13.1.3.3.1
This entry includes a destination IP address to which to send traps for this community. It also includes a backup address in case the primary address does not acknowledge the trap.
Status: mandatory	Access: not-accessible
OBJECT-TYPE
	TrapDestEntry

trapDestIndex		1.3.6.1.4.1.11.2.13.1.3.3.1.1
A value that uniquely identifies this trapDestEntry.
Status: mandatory	Access: read-only
OBJECT-TYPE
	INTEGER	1..65535

trapDestCommunity		1.3.6.1.4.1.11.2.13.1.3.3.1.2
A community to which these destination IP addresses belong. This entry is associated with any eventEntries in the RMON MIB whose value of eventCommunity is equal to the value of this object. Every time an associated event entry sends a trap due to an event, that trap will be sent according to the addresses specified in this entry. This object may not be modifed if the associated trapDestStatus object is equal to valid(1).
Status: mandatory	Access: read-write
OBJECT-TYPE
	DisplayString	Size(0..127)

trapDestDeliveryType		1.3.6.1.4.1.11.2.13.1.3.3.1.3
If this object has the value one-shot(1), then the trap will be sent only once to the primary address without requiring acknowledgement. If this object has the value acknowleged(2), then the trap will be sent to the primary address expecting an acknowledgement. If the trap is not acknowledged within the time specified by trapMaxTimeOut, then the trap is retransmitted (with the same sequence number) to the primary address. The trap is retransmitted at most trapMaxRetries times until acknowledged. If the trap is still not acknowleged and the alternate address is not 0.0.0.0, then it is sent to the alternate address at most trapMaxRetries plus one times until acknowledged. This object may not be modifed if the associated trapDestStatus object is equal to valid(1).
Status: mandatory	Access: read-write
OBJECT-TYPE
	INTEGER	one-shot(1)

trapDestPrimaryIpAddress		1.3.6.1.4.1.11.2.13.1.3.3.1.4
The primary IP address to which to send traps. This object may not be modifed if the associated trapDestStatus object is equal to valid(1).
Status: mandatory	Access: read-write
OBJECT-TYPE
	IpAddress

trapDestPrimaryIfIndex		1.3.6.1.4.1.11.2.13.1.3.3.1.5
The value of this object uniquely identifies the interface on this device through which the host at trapPrimaryIpAddress can be reached. The interface identified by a particular value of this object is the same interface as identified by the same value of the ifIndex object, defined in RFC 1213. This object may not be modifed if the associated trapDestStatus object is equal to valid(1).
Status: mandatory	Access: read-write
OBJECT-TYPE
	INTEGER	1..65535

trapDestOwner		1.3.6.1.4.1.11.2.13.1.3.3.1.8
The owner of this trap destination entry.
Status: mandatory	Access: read-write
OBJECT-TYPE
	OwnerString

trapDestStatus		1.3.6.1.4.1.11.2.13.1.3.3.1.9
The status of this trap destination entry.
Status: mandatory	Access: read-write
OBJECT-TYPE
	EntryStatus

serialConnectionTable		1.3.6.1.4.1.11.2.15.5
A list of serial connection entries.
Status: mandatory	Access: not-accessible
OBJECT-TYPE
	SEQUENCE OF
		SerialConnectionEntry

serialConnectionEntry		1.3.6.1.4.1.11.2.15.5.1
Configuration for a SLIP link over a serial line.
Status: mandatory	Access: not-accessible
OBJECT-TYPE
	SerialConnectionEntry

serialConnectIndex		1.3.6.1.4.1.11.2.15.5.1.1
A value that uniquely identifies this serialConnection entry.
Status: mandatory	Access: read-only
OBJECT-TYPE
	INTEGER	1..65535

serialConnectDestIpAddress		1.3.6.1.4.1.11.2.15.5.1.2
The IP Address that can be reached at the other end of this serial connection. This object may not be modifed if the associated serialConnectStatus object is equal to valid(1).
Status: mandatory	Access: read-write
OBJECT-TYPE
	IpAddress

serialConnectType		1.3.6.1.4.1.11.2.15.5.1.3
The type of outgoing connection to make. If this object has the value direct(1), then a direct serial connection is assumed. If this object has the value modem(2), then serialConnectDialString will be used to make a modem connection. If this object has the value switch(3), then serialConnectSwitchConnectSeq will be used to establish the connection over a serial data switch, and serialConnectSwitchDisconnectSeq will be used to terminate the connection. If this object has the value modem-switch(4), then a modem connection will be made first followed by the switch connection. This object may not be modifed if the associated serialConnectStatus object is equal to valid(1).
Status: mandatory	Access: read-write
OBJECT-TYPE
	INTEGER	direct(1), modem(2), switch(3), modem-switch(4)

serialConnectDialString		1.3.6.1.4.1.11.2.15.5.1.4
A control string which specifies how to dial the phone number in order to establish a modem connection. The string should include dialing prefix and suffix. For example: ``^s^MATD9,888-1234^M'' will instruct the Probe to send a carriage return followed by the dialing prefix ``ATD'', the phone number ``9,888-1234'', and a carriage return as the dialing suffix. This object may not be modifed if the associated serialConnectStatus object is equal to valid(1).
Status: mandatory	Access: read-write
OBJECT-TYPE
	ControlString	Size(0..255)

serialConnectSwitchConnectSeq		1.3.6.1.4.1.11.2.15.5.1.5
A control string which specifies how to establish a data switch connection. This object may not be modifed if the associated serialConnectStatus object is equal to valid(1).
Status: mandatory	Access: read-write
OBJECT-TYPE
	ControlString	Size(0..255)

serialConnectSwitchDisconnectSeq		1.3.6.1.4.1.11.2.15.5.1.6
A control string which specifies how to terminate a data switch connection. This object may not be modifed if the associated serialConnectStatus object is equal to valid(1).
Status: mandatory	Access: read-write
OBJECT-TYPE
	ControlString	Size(0..255)

serialConnectSwitchResetSeq		1.3.6.1.4.1.11.2.15.5.1.7
A control string which specifies how to reset a data switch in the event of a timeout. This object may not be modifed if the associated serialConnectStatus object is equal to valid(1).
Status: mandatory	Access: read-write
OBJECT-TYPE
	ControlString	Size(0..255)

serialConnectOwner		1.3.6.1.4.1.11.2.15.5.1.8
The owner of this serial connection entry.
Status: mandatory	Access: read-write
OBJECT-TYPE
	OwnerString

serialConnectStatus		1.3.6.1.4.1.11.2.15.5.1.9
The status of this serial connection entry. If the manager attempts to set this object to valid(1) when the serialConnectType is set to modem(2) or modem-switch(4) and the serialConnectDialString is a zero-length string or cannot be correctly parsed as a ConnectString, the set request will be rejected with badValue(3). If the manager attempts to set this object to valid(1) when the serialConnectType is set to switch(3) or modem-switch(4) and the serialConnectSwitchConnectSeq, the serialConnectSwitchDisconnectSeq, or the serialConnectSwitchResetSeq cannot be correctly parsed as ConnectStrings, the set request will be rejected with badValue(3). Note that in these cases, zero-length strings should be considered to be valid and parsable strings. Thus, a set request should not be rejected in the case where any of the three serialConnectSwitchxxxxxSeq strings are of 0 length. The set should only be rejected if a non-zero length string cannot be correctly parsed.
Status: mandatory	Access: read-write
OBJECT-TYPE
	EntryStatus

currentUtilizationPeriod		1.3.6.1.4.1.11.2.3.7.6.1.5.1.1
The number of seconds over which the currentUtilization object is calculated. Any change to this variable causes the value of currentUtilization to be set to all 1's. On a multi-interface probe, this parameter applies only to interface index 1. Refer to currentUtilizationTable in this document for the current utilization parameters for the other interfaces on a multi- interface probe.
Status: mandatory	Access: read-write
OBJECT-TYPE
	INTEGER	1..3600

currentUtilization		1.3.6.1.4.1.11.2.3.7.6.1.5.1.2
NOTE: Because, this variable has been obsoleted by the currentUtilizationTable, it will be deprecated in a future firmware release. Applications should migrate to the new MIB variable as soon as possible. The best estimate of the mean physical layer network utilization on the monitor's physical interface during the previous number of seconds defined by currentUtilizationPeriod. The units of this object are hundredths of a percent. Its value will normally be in the range (0..10000). A value of all 1's means that a full currentUtilizationPeriod has not passed since either monitor startup or the last time currentUtilizationPeriod was changed. On a multi-interface probe, this value applies only to interface index 1. Refer to currentUtilizationTable in this document for the current utilization value for the other interfaces on a multi- interface probe.
Status: mandatory	Access: read-only
OBJECT-TYPE
	INTEGER

currentUtilizationTable		1.3.6.1.4.1.11.2.3.7.6.1.5.1.7
A table of current utilizations for multi-port probes.
Status: mandatory	Access: not-accessible
OBJECT-TYPE
	SEQUENCE OF
		CurrentUtilizationEntry

currentUtilizationEntry		1.3.6.1.4.1.11.2.3.7.6.1.5.1.7.1
The current utilization period and current utilization for a particular interface on a multi-interface probe.
Status: mandatory	Access: not-accessible
OBJECT-TYPE
	CurrentUtilizationEntry

curUtilIfIndex		1.3.6.1.4.1.11.2.3.7.6.1.5.1.7.1.1
The value of this object uniquely identifies the physical interface on this device for which this entry contains current utilization parameters. The interface identified by a particular value of this object is the same interface as identified by the same value of the ifIndex object, defined in RFC 1213.
Status: mandatory	Access: read-only
OBJECT-TYPE
	INTEGER	1..65535

curUtilPeriod		1.3.6.1.4.1.11.2.3.7.6.1.5.1.7.1.2
The number of seconds over which the current utilization object for this entry in the table is calculated. Any change to this variable causes the value of curUtil for this entry to be set to all 1's
Status: mandatory	Access: read-write
OBJECT-TYPE
	INTEGER

curUtil		1.3.6.1.4.1.11.2.3.7.6.1.5.1.7.1.3
The best estimate of the mean physical layer network utilization on the monitor's physical interface during the previous number of seconds defined by curUtilPeriod for this entry in the table. The units of this object are hundredths of a percent. Its value will normally be in the range (0..10000). A value of all 1's means that a full curUtilPeriod for this entry in the table has not passed since either monitor startup or the last time curUtilPeriod was changed. For probes which support full-duplex media, this variable should reflect the mean physical layer network utilization for both directions combined. For example, if the two directions of a Fast Ethernet full duplex connection are 90% and 50%, this variable should reflect a value of 70%.
Status: mandatory	Access: read-only
OBJECT-TYPE
	INTEGER

curUtilReceive		1.3.6.1.4.1.11.2.3.7.6.1.5.1.7.1.4
The best estimate of the mean physical layer network utilization on the monitor's physical interface during the previous number of seconds defined by curUtilPeriod for this entry in the table. The units of this object are hundredths of a percent. Its value will normally be in the range (0..10000). A value of all 1's means that a full curUtilPeriod for this entry in the table has not passed since either monitor startup or the last time curUtilPeriod was changed. For a LAN interface with the exception of the Fast Ethernet LanProbe option 201, this value should be zero. For the Fast Ethernet LanProbe option 201, a WanProbe or ATMProbe, this value should reflect the network traffic on the receive wires/cable.
Status: mandatory	Access: read-only
OBJECT-TYPE
	INTEGER

curUtilTransmit		1.3.6.1.4.1.11.2.3.7.6.1.5.1.7.1.5
The best estimate of the mean physical layer network utilization on the monitor's physical interface during the previous number of seconds defined by curUtilPeriod for this entry in the table. The units of this object are hundredths of a percent. Its value will normally be in the range (0..10000). A value of all 1's means that a full curUtilPeriod for this entry in the table has not passed since either monitor startup or the last time curUtilPeriod was changed. For a LAN interface with the exception of the Fast Ethernet LanProbe option 201, this value should be zero. For the Fast Ethernet LanProbe option 201, a WanProbe or ATMProbe, this value should reflect the network traffic on the receive wires/cable.
Status: mandatory	Access: read-only
OBJECT-TYPE
	INTEGER

hostExtDuplicateNetAddresses		1.3.6.1.4.1.11.2.3.7.6.1.5.4.1
This counter is incremented every time the monitor detects a second host using the same network address as another host. This object can be the target of an RMON alarm, for the purpose of discovering duplicate network addresses.
Status: mandatory	Access: read-only
OBJECT-TYPE
	Counter

hostExtDuplicateNetEvent		1.3.6.1.4.1.11.2.3.7.6.1.5.4.2
The index of the eventEntry in the RMON MIB that is used whenever the value of hostExtDuplicateNetAddresses changes. The eventEntry identified by a particular value of this index is the same as identified by the same value of the eventIndex object. If there is no corresponding entry in the eventTable, then no association exists. In particular, if this value is zero, no associated event will be generated, as zero is not a valid event index.
Status: mandatory	Access: read-write
OBJECT-TYPE
	INTEGER	0..65535

hostExtLastDuplicateNetAddress		1.3.6.1.4.1.11.2.3.7.6.1.5.4.3
The network address that was being used by two different hosts (represented by hostExtLastDuplicateHost1 and hostExtLasDuplicateHost2). The value of this object will correspond with the detection event that caused the latest increment of the hostExtDuplicateNetAddresses object.
Status: mandatory	Access: read-only
OBJECT-TYPE
	OCTET STRING

hostExtLastDuplicateHost1		1.3.6.1.4.1.11.2.3.7.6.1.5.4.4
The MAC address of one of the two last hosts to be detected using a duplicate network level address. The value of this object will correspond with the detection event that caused the latest increment of the hostExtDuplicateNetAddresses object.
Status: mandatory	Access: read-only
OBJECT-TYPE
	OCTET STRING

hostExtLastDuplicateHost2		1.3.6.1.4.1.11.2.3.7.6.1.5.4.5
The MAC address of the other of the two last hosts to be detected using a duplicate network level address. The value of this object will correspond with the detection event that caused the latest increment of the hostExtDuplicateNetAddresses object.
Status: mandatory	Access: read-only
OBJECT-TYPE
	OCTET STRING

hostExtChangedNetAddresses		1.3.6.1.4.1.11.2.3.7.6.1.5.4.6
This counter is incremented every time the monitor detects that a host has changed the network address it is using. It is not incremented by detection of a host's initial use of a network address. This object can be the target of an RMON alarm.
Status: mandatory	Access: read-only
OBJECT-TYPE
	Counter

hostExtChangedNetEvent		1.3.6.1.4.1.11.2.3.7.6.1.5.4.7
The index of the eventEntry in the RMON MIB that is used whenever the value of hostExtChangedNetAddresses changes. The eventEntry identified by a particular value of this index is the same as identified by the same value of the eventIndex object. If there is no corresponding entry in the eventTable, then no association exists. In particular, if this value is zero, no associated event will be generated, as zero is not a valid event index.
Status: mandatory	Access: read-write
OBJECT-TYPE
	INTEGER	0..65535

hostExtLastChangedHost		1.3.6.1.4.1.11.2.3.7.6.1.5.4.8
The MAC address of the last host which was detected to have changed the network address it was using. The value of this object will correspond with the detection event that caused the latest increment of the hostExtChangedNetAddresses object.
Status: mandatory	Access: read-only
OBJECT-TYPE
	OCTET STRING

hostExtLastOldNetAddress		1.3.6.1.4.1.11.2.3.7.6.1.5.4.9
The network address that the host represented by hostExtLastChangedHost was previously using. The value of this object will correspond with the detection event that caused the latest increment of the hostExtChangedNetAddresses object.
Status: mandatory	Access: read-only
OBJECT-TYPE
	OCTET STRING

hostExtLastNewNetAddress		1.3.6.1.4.1.11.2.3.7.6.1.5.4.10
The network address that the host represented by hostExtLastChangedHost is currently using. The value of this object will correspond with the detection event that caused the latest increment of the hostExtChangedNetAddresses object.
Status: mandatory	Access: read-only
OBJECT-TYPE
	OCTET STRING

hostExtTable		1.3.6.1.4.1.11.2.3.7.6.1.5.4.11
A list of extensions to the RMON MIB Host Table
Status: mandatory	Access: not-accessible
OBJECT-TYPE
	SEQUENCE OF
		HostExtEntry

hostExtEntry		1.3.6.1.4.1.11.2.3.7.6.1.5.4.11.1
A collection of additional statistics for a particular host that has been discovered on an interface of this device.
Status: mandatory	Access: not-accessible
OBJECT-TYPE
	HostExtEntry

hostExtIndex		1.3.6.1.4.1.11.2.3.7.6.1.5.4.11.1.1
The set of collected host statistics of which this entry is a part. The set of hosts identified by a particular value of this index is associated with the hostControlEntry as identified by the same value of hostControlIndex.
Status: mandatory	Access: read-only
OBJECT-TYPE
	INTEGER	1..65535

hostExtMacAddress		1.3.6.1.4.1.11.2.3.7.6.1.5.4.11.1.2
The physical address of this host.
Status: mandatory	Access: read-only
OBJECT-TYPE
	OCTET STRING

hostExtNetAddrType		1.3.6.1.4.1.11.2.3.7.6.1.5.4.11.1.3
The type of network address used in packets sent by this host.
Status: mandatory	Access: read-only
OBJECT-TYPE
	INTEGER	ip(1)

hostExtNetAddrStatus		1.3.6.1.4.1.11.2.3.7.6.1.5.4.11.1.4
The level of knowledge the monitor has of the network address used by this host. Values greater than known(2) indicate that this host has used more than one network address since the last time the monitor restarted. A value of multipleChanges(4) might indicate that this host is acting as a router.
Status: mandatory	Access: read-only
OBJECT-TYPE
	INTEGER	unknown(1), known(2), changedOnce(3), multipleChanges(4)

hostExtNetAddress		1.3.6.1.4.1.11.2.3.7.6.1.5.4.11.1.5
The network address for this host. The expected length of this object is dependent on the value of hostExtNetAddrType. If hostExtNetAddrStatus == multipleChanges(4), and hostExtNetAddrType == ip(1), the value of this object is undefined.
Status: mandatory	Access: read-only
OBJECT-TYPE
	OCTET STRING

hostExtCreationOrder		1.3.6.1.4.1.11.2.3.7.6.1.5.4.11.1.6
An Index that defines the relative ordering of the creation time of hosts caputed for a particular hostControlEntry. This index shall be between 1 and N, where N is the value of the associated hostControlTableSize. The ordering of the indexes is based on the order of each entry's insertion into the table, in which entries added earlier have a lower index value than entries added later. Basically, this variable is exactly the same as the hostCreationOrder variable in the RMON MIB definition.
Status: mandatory	Access: read-only
OBJECT-TYPE
	INTEGER	1..65535

hostExtLastUpdateTime		1.3.6.1.4.1.11.2.3.7.6.1.5.4.11.1.7
The value of the SysUptime variable the last time that the corresponding hostEntry was updated.
Status: mandatory	Access: read-only
OBJECT-TYPE
	TimeTicks

hostTimeExtTable		1.3.6.1.4.1.11.2.3.7.6.1.5.4.12
A list of extensions to the RMON MIB Host Time Table
Status: mandatory	Access: not-accessible
OBJECT-TYPE
	SEQUENCE OF
		HostTimeExtEntry

hostTimeExtEntry		1.3.6.1.4.1.11.2.3.7.6.1.5.4.12.1
A collection of additional statistics for a particular host that has been discovered on an interface of this device.
Status: mandatory	Access: not-accessible
OBJECT-TYPE
	HostTimeExtEntry

hostTimeExtIndex		1.3.6.1.4.1.11.2.3.7.6.1.5.4.12.1.1
The set of collected host statistics of which this entry is a part. The set of hosts identified by a particular value of this index is associated with the hostControlEntry as identified by the same value of hostControlIndex.
Status: mandatory	Access: read-only
OBJECT-TYPE
	INTEGER	1..65535

hostTimeExtMacAddress		1.3.6.1.4.1.11.2.3.7.6.1.5.4.12.1.2
The physical address of this host.
Status: mandatory	Access: read-only
OBJECT-TYPE
	OCTET STRING

hostTimeExtNetAddrType		1.3.6.1.4.1.11.2.3.7.6.1.5.4.12.1.3
The type of network address used in packets sent by this host.
Status: mandatory	Access: read-only
OBJECT-TYPE
	INTEGER	ip(1)

hostTimeExtNetAddrStatus		1.3.6.1.4.1.11.2.3.7.6.1.5.4.12.1.4
The level of knowledge the monitor has of the network address used by this host. Values greater than known(2) indicate that this host has used more than one network address since the last time the monitor restarted. A value of multipleChanges(4) might indicate that this host is acting as a router.
Status: mandatory	Access: read-only
OBJECT-TYPE
	INTEGER	unknown(1), known(2), changedOnce(3), multipleChanges(4)

hostTimeExtNetAddress		1.3.6.1.4.1.11.2.3.7.6.1.5.4.12.1.5
The network address for this host. The expected length of this object is dependent on the value of hostTimeExtNetAddrType. If hostTimeExtNetAddrStatus == multipleChanges(4), and hostTimeExtNetAddrType == ip(1), the value of this object is undefined.
Status: mandatory	Access: read-only
OBJECT-TYPE
	OCTET STRING

hostTimeExtCreationOrder		1.3.6.1.4.1.11.2.3.7.6.1.5.4.12.1.6
An Index that defines the relative ordering of the creation time of hosts caputed for a particular hostControlEntry. This index shall be between 1 and N, where N is the value of the associated hostControlTableSize. The ordering of the indexes is based on the order of each entry's insertion into the table, in which entries added earlier have a lower index value than entries added later. Basically, this variable is exactly the same as the hostCreationOrder variable in the RMON MIB definition.
Status: mandatory	Access: read-only
OBJECT-TYPE
	INTEGER	1..65535

hostTimeExtLastUpdateTime		1.3.6.1.4.1.11.2.3.7.6.1.5.4.12.1.7
The value of the SysUptime variable the last time that the corresponding hostEntry was updated.
Status: mandatory	Access: read-only
OBJECT-TYPE
	TimeTicks

channelExtTable		1.3.6.1.4.1.11.2.3.7.6.1.5.7.2
A list of extensions to RMON packet channel entries.
Status: mandatory	Access: not-accessible
OBJECT-TYPE
	SEQUENCE OF
		ChannelExtEntry

channelExtEntry		1.3.6.1.4.1.11.2.3.7.6.1.5.7.2.1
A set of additional parameters for a RMON packet channel applied on a particular interface.
Status: mandatory	Access: not-accessible
OBJECT-TYPE
	ChannelExtEntry

channelExtIndex		1.3.6.1.4.1.11.2.3.7.6.1.5.7.2.1.1
An index that uniquely identifies an entry in the channel table. Each such entry defines one channel, a logical data and event stream. The channel identified by a particular value of this object is identical to one associated with a like value of the RMON object channelIndex.
Status: mandatory	Access: read-only
OBJECT-TYPE
	INTEGER	1..65535

channelExtSelfPktCapture		1.3.6.1.4.1.11.2.3.7.6.1.5.7.2.1.2
The value of this object indicates whether or not packets that are sent to or from the MAC address of the monitor should pass through this channel.
Status: mandatory	Access: read-write
OBJECT-TYPE
	INTEGER	captureMyOwn(1), ignoreMyOwn(2)

channelExtDropEvents		1.3.6.1.4.1.11.2.3.7.6.1.5.7.3
The total number of events in which packets were dropped for all channels due to lack of resources in the probe. Note that this number is not necessarily the number of packets dropped; it is just the number of times this condition has been detected.
Status: mandatory	Access: read-only
OBJECT-TYPE
	INTEGER

echoTestSSTable		1.3.6.1.4.1.11.2.3.7.6.1.6.1
A table of instructions for and results of one-shot network connectivity tests
Status: mandatory	Access: not-accessible
OBJECT-TYPE
	SEQUENCE OF
		EchoTestSSEntry

echoTestSSEntry		1.3.6.1.4.1.11.2.3.7.6.1.6.1.1
A collection of objects that describe the form of and give the results of a one-shot connectivity test to a given host.
Status: mandatory	Access: not-accessible
OBJECT-TYPE
	EchoTestSSEntry

echoTestSSIndex		1.3.6.1.4.1.11.2.3.7.6.1.6.1.1.1
An index that uniquely identifies an entry in the echoTestSS table. Each such entry defines a single shot echo test to the node corresponding to either the mac address or net address objects.
Status: mandatory	Access: read-only
OBJECT-TYPE
	INTEGER	1..65535

echoTestSSIfIndex		1.3.6.1.4.1.11.2.3.7.6.1.6.1.1.2
The value of this object uniquely identifies the interface on this remote network monitoring device on which the echo test will be performed. The interface identified by a particular value of this object is the same interface as identified by the same value of the ifIndex object, defined in RFC 1156 and RFC 1213.
Status: mandatory	Access: read-write
OBJECT-TYPE
	INTEGER	1..65535

echoTestSSMacAddress		1.3.6.1.4.1.11.2.3.7.6.1.6.1.1.3
The MAC level address for this host.
Status: mandatory	Access: read-write
OBJECT-TYPE
	OCTET STRING

echoTestSSNetAddress		1.3.6.1.4.1.11.2.3.7.6.1.6.1.1.4
The network level address for this host.
Status: mandatory	Access: read-write
OBJECT-TYPE
	OCTET STRING

echoTestSSProtocol		1.3.6.1.4.1.11.2.3.7.6.1.6.1.1.5
The type of echo test to perform.
Status: mandatory	Access: read-write
OBJECT-TYPE
	INTEGER	icmp-echo(1), ieee-802-2(2), ethernet-ctp(3), novell-802-3(4), novell-ethernet(5), vines-datalink(6), appleTalk(7), novell-802-2(8)

echoTestSSTimeout		1.3.6.1.4.1.11.2.3.7.6.1.6.1.1.6
The number of milliseconds to wait for a reply before retransmitting the echo request packet. Note that a monitor may impose a lower bound on this object if its timing facilities are limited.
Status: mandatory	Access: read-write
OBJECT-TYPE
	INTEGER

echoTestSSRetryAttempts		1.3.6.1.4.1.11.2.3.7.6.1.6.1.1.7
The number of times to retransmit the echo request packet should a response packet not be received before echoTestSSTimeout expires.
Status: mandatory	Access: read-write
OBJECT-TYPE
	INTEGER	0..9

echoTestSSLastEchoStatus		1.3.6.1.4.1.11.2.3.7.6.1.6.1.1.8
The result of this echo test.
Status: mandatory	Access: read-only
OBJECT-TYPE
	INTEGER	no-results-available(1), response-received(2), response-timed-out(3)

echoTestSSResponseNumber		1.3.6.1.4.1.11.2.3.7.6.1.6.1.1.9
The number of echo request packets sent before a successful response packet was received. The value of this object will be non-zero only when echoTestSSLastEchoStatus is equal to response_received(2)
Status: mandatory	Access: read-only
OBJECT-TYPE
	INTEGER

echoTestSSResponseTime		1.3.6.1.4.1.11.2.3.7.6.1.6.1.1.10
The number of milliseconds between the time the last echo request packet was transmitted and a response packet was received. The value of this object will be non-zero only when echoTestSSLastEchoStatus is equal to response_received(2)
Status: mandatory	Access: read-only
OBJECT-TYPE
	INTEGER

echoTestSSOwner		1.3.6.1.4.1.11.2.3.7.6.1.6.1.1.11
The entity that configured this entry and is therefore using the resources assigned to it.
Status: mandatory	Access: read-write
OBJECT-TYPE
	OwnerString

echoTestSSStatus		1.3.6.1.4.1.11.2.3.7.6.1.6.1.1.12
The status of this row.
Status: mandatory	Access: read-write
OBJECT-TYPE
	EntryStatus

echoTestPeriodicTable		1.3.6.1.4.1.11.2.3.7.6.1.6.2
A table of instructions for and results of periodic network connectivity tests
Status: mandatory	Access: not-accessible
OBJECT-TYPE
	SEQUENCE OF
		EchoTestPeriodicEntry

echoTestPeriodicEntry		1.3.6.1.4.1.11.2.3.7.6.1.6.2.1
A collection of objects that describe the form of and give the results of periodic connectivity tests to a given host.
Status: mandatory	Access: not-accessible
OBJECT-TYPE
	EchoTestPeriodicEntry

echoTestPeriodicIndex		1.3.6.1.4.1.11.2.3.7.6.1.6.2.1.1
An index that uniquely identifies an entry in the echoTestPeriodic table. Each such entry defines a periodic echo test to the node corresponding to either the mac address or net address objects.
Status: mandatory	Access: read-only
OBJECT-TYPE
	INTEGER	1..65535

echoTestPeriodicIfIndex		1.3.6.1.4.1.11.2.3.7.6.1.6.2.1.2
The value of this object uniquely identifies the interface on this remote network monitoring device on which the echo test will be performed. The interface identified by a particular value of this object is the same interface as identified by the same value of the ifIndex object, defined in RFC 1156 and RFC 1213.
Status: mandatory	Access: read-write
OBJECT-TYPE
	INTEGER	1..65535

echoTestPeriodicMacAddress		1.3.6.1.4.1.11.2.3.7.6.1.6.2.1.3
The MAC level address of this host.
Status: mandatory	Access: read-write
OBJECT-TYPE
	OCTET STRING

echoTestPeriodicNetAddress		1.3.6.1.4.1.11.2.3.7.6.1.6.2.1.4
The network level address of this host.
Status: mandatory	Access: read-write
OBJECT-TYPE
	OCTET STRING

echoTestPeriodicProtocol		1.3.6.1.4.1.11.2.3.7.6.1.6.2.1.5
The type of echo test to perform. Note that only one test can be selected at a time.
Status: mandatory	Access: read-write
OBJECT-TYPE
	INTEGER	icmp-echo(1), ieee-802-2(2), ethernet-ctp(3), novell-802-3(4), novell-ethernet(5), vines-datalink(6), appleTalk(7), novell-802-2(8)

echoTestPeriodicTimeout		1.3.6.1.4.1.11.2.3.7.6.1.6.2.1.6
The number of milliseconds to wait for a reply before retransmitting the echo request packet. Note that a monitor may impose a lower bound on this object if its timing facilities are limited.
Status: mandatory	Access: read-write
OBJECT-TYPE
	INTEGER

echoTestPeriodicRetryAttempts		1.3.6.1.4.1.11.2.3.7.6.1.6.2.1.7
The number of times to retransmit the echo request packet should a response packet not be received before echoTestPeriodicTimeout expires.
Status: mandatory	Access: read-write
OBJECT-TYPE
	INTEGER	0..9

echoTestPeriodicNoResponseEventIndex		1.3.6.1.4.1.11.2.3.7.6.1.6.2.1.8
The index of the eventEntry in the RMON MIB that is used whenever the value of echoTestPeriodicLastEchoStatus changes to response_timed_out(3). The eventEntry identified by a particular value of this index is the same as identified by the same value of the eventIndex object. If there is no corresponding entry in the eventTable, then no association exists. In particular, if this value is zero, no associated event will be generated, as zero is not a valid event index.
Status: mandatory	Access: read-write
OBJECT-TYPE
	INTEGER	0..65535

echoTestPeriodicRespondedEventIndex		1.3.6.1.4.1.11.2.3.7.6.1.6.2.1.9
The index of the eventEntry in the RMON MIB that is used whenever the value of echoTestPeriodicLastEchoStatus changes from response_timed_out(3) to response_received(2). The eventEntry identified by a particular value of this index is the same as identified by the same value of the eventIndex object. If there is no corresponding entry in the eventTable, then no association exists. In particular, if this value is zero, no associated event will be generated, as zero is not a valid event index.
Status: mandatory	Access: read-write
OBJECT-TYPE
	INTEGER	0..65535

echoTestPeriodicEchoState		1.3.6.1.4.1.11.2.3.7.6.1.6.2.1.10
The current state of testing for this echoTestPeriodicEntry. Once a successful response has been received, this object will alternate between waiting_to_echo(3) and waiting_for_subsequent_response(4). Whenever the value of echoTestPeriodicLastEchoStatus changes to response_timed_out(3), this object's value will revert to waiting_for_initial_response(2).
Status: mandatory	Access: read-only
OBJECT-TYPE
	INTEGER	no-echo-sent(1), waiting-for-initial-response(2), waiting-to-echo(3), waiting-for-subsequent-response(4)

echoTestPeriodicLastEchoStatus		1.3.6.1.4.1.11.2.3.7.6.1.6.2.1.11
The result of the last echo test for this entry.
Status: mandatory	Access: read-only
OBJECT-TYPE
	INTEGER	no-results-available(1), response-received(2), response-timed-out(3)

echoTestPeriodicTotalOperations		1.3.6.1.4.1.11.2.3.7.6.1.6.2.1.12
The total number of times that echoTestPeriod has expired and an echo test has been initiated for this host.
Status: mandatory	Access: read-only
OBJECT-TYPE
	INTEGER

echoTestPeriodicSuccessfulOperations		1.3.6.1.4.1.11.2.3.7.6.1.6.2.1.13
The total number of times that an echo test has completed successfully with the reception of a correct response packet. This number will always be less than or equal to echoTestPeriodicTotalOperations.
Status: mandatory	Access: read-only
OBJECT-TYPE
	INTEGER

echoTestPeriodicMinRespTime		1.3.6.1.4.1.11.2.3.7.6.1.6.2.1.14
The shortest time (in milliseconds) between request and response for all of the periodic echo tests that have been attempted for this host.
Status: mandatory	Access: read-only
OBJECT-TYPE
	INTEGER

echoTestPeriodicMaxRespTime		1.3.6.1.4.1.11.2.3.7.6.1.6.2.1.15
The longest time (in milliseconds) between request and response for all of the periodic echo tests that have been attempted for this host.
Status: mandatory	Access: read-only
OBJECT-TYPE
	INTEGER

echoTestPeriodicLastRespTime		1.3.6.1.4.1.11.2.3.7.6.1.6.2.1.16
The time (in milliseconds) between request and response for the last echo test attempted for this host. If the value of echoTestPeriodicLastEchoStatus for this host is not response_received(2), the value returned will be -1.
Status: mandatory	Access: read-only
OBJECT-TYPE
	INTEGER

echoTestPeriodicTotalRespTime		1.3.6.1.4.1.11.2.3.7.6.1.6.2.1.17
The sum of all the response times (in milliseconds) for all of the periodic echo tests that have been attempted for this host. This object and echoTestPeriodicSuccessfulOperations can be used to calculate an average response time for this host
Status: mandatory	Access: read-only
OBJECT-TYPE
	INTEGER

echoTestPeriodicOwner		1.3.6.1.4.1.11.2.3.7.6.1.6.2.1.18
The entity that configured this entry and is therefore using the resources assigned to it.
Status: mandatory	Access: read-write
OBJECT-TYPE
	OwnerString

echoTestPeriodicStatus		1.3.6.1.4.1.11.2.3.7.6.1.6.2.1.19
The status of this row.
Status: mandatory	Access: read-write
OBJECT-TYPE
	EntryStatus

echoTestPeriodicSumOfSquaresTimeLo		1.3.6.1.4.1.11.2.3.7.6.1.6.2.1.20
The sum of the square of all the response times (in milliseconds) for all of the periodic tests analogous to targetTotalResponseTime. This object, targetTotalResponseTime, and targetSuccessfulOperations can be used to calculate a standard deviation of response time for this host. This is the low order unsigned long portion of the value.
Status: mandatory	Access: read-only
OBJECT-TYPE
	INTEGER

echoTestPeriodicSumOfSquaresTimeHi		1.3.6.1.4.1.11.2.3.7.6.1.6.2.1.21
The sum of the square of all the response times (in milliseconds) for all of the periodic tests analogous to targetTotalResponseTime. This object, targetTotalResponseTime, and targetSuccessfulOperations can be used to calculate a standard deviation of response time for this host. This is the high order unsigned long portion of the value.
Status: mandatory	Access: read-only
OBJECT-TYPE
	INTEGER

echoTestPeriodicFailedAttemptCount		1.3.6.1.4.1.11.2.3.7.6.1.6.2.1.22
The total count of failed attempts
Status: mandatory	Access: read-only
OBJECT-TYPE
	INTEGER

echoTestPeriodicMinRespTime30MinInt		1.3.6.1.4.1.11.2.3.7.6.1.6.2.1.23
Minimum response time (in milliseconds) value for the last 30 minute interval. The agent must update this object every 30 minutes, aligning to the system clock at every hour and half hour. If there is no valid value available for this object because the test hasn't been running for 30 minutes, or there was no response received in the last 30 minutes, -1 will be returned.
Status: mandatory	Access: read-only
OBJECT-TYPE
	INTEGER

echoTestPeriodicMaxRespTime30MinInt		1.3.6.1.4.1.11.2.3.7.6.1.6.2.1.24
Maximum response time (in milliseconds) value for the last 30 minute interval. The agent must update this object every 30 minutes, aligning to the system clock at every hour and half hour. If there is no valid value available for this object because the test hasn't been running for 30 minutes, or there was no response received in the last 30 minutes, -1 will be returned.
Status: mandatory	Access: read-only
OBJECT-TYPE
	INTEGER

echoTestPeriodicMinRespTime5MinInt		1.3.6.1.4.1.11.2.3.7.6.1.6.2.1.25
Minimum response time (in milliseconds) value for the last 5 minute interval. The agent must update this object every 5 minutes, aligning to the system clock at every 5 minute interval. If there is no valid value available for this object because the test hasn't been running for 5 minutes, or there was no response received in the last 5 minutes, -1 will be returned.
Status: mandatory	Access: read-only
OBJECT-TYPE
	INTEGER

echoTestPeriodicMaxRespTime5MinInt		1.3.6.1.4.1.11.2.3.7.6.1.6.2.1.26
Maximum response time (in milliseconds) value for the last 5 minute interval. The agent must update this object every 5 minutes, aligning to the system clock at every 5 minute interval. If there is no valid value available for this object because the test hasn't been running for 5 minutes, or there was no response received in the last 5 minutes, -1 will be returned.
Status: mandatory	Access: read-only
OBJECT-TYPE
	INTEGER

echoTestPeriod		1.3.6.1.4.1.11.2.3.7.6.1.6.3
This object indicates how long to wait (in seconds) after completion of a pass through the echoTestPeriodic table before starting a new pass. Whenever this object is set to zero(0), the periodic echo list is disabled. Whenever it is set to a non-zero value, an initial round of tests will be scheduled immediately, and subsequent rounds will start after the specified period. Note that a monitor may impose a lower bound on this object if its timing facilities are limited.
Status: mandatory	Access: read-write
OBJECT-TYPE
	INTEGER

echoTestPeriodicCount		1.3.6.1.4.1.11.2.3.7.6.1.6.4
This object indicates how many complete passes through the echoTestPeriodicTable have occurred since it was last restarted. Its value will be zero(0) until the first pass is complete.
Status: mandatory	Access: read-only
OBJECT-TYPE
	INTEGER

echoTestResetSSTable		1.3.6.1.4.1.11.2.3.7.6.1.6.5
This is a control/status object for the echoTestSSTable. When there are entries in the table, this object's value is table-in-use(3). When set to reset-the-table(3), all entries are deleted, and this object's value changes to table-is-empty(1).
Status: mandatory	Access: read-write
OBJECT-TYPE
	INTEGER	table-is-empty(1), table-in-use(2), reset-the-table(3)

echoTestResetPeriodicTable		1.3.6.1.4.1.11.2.3.7.6.1.6.6
This is a control/status object for the echoTestListTable. When there are entries in the table, this object's value is table_in_use(3). When set to reset_the_table(3), all entries are deleted, and this object's value changes to table_is_empty(1).
Status: mandatory	Access: read-write
OBJECT-TYPE
	INTEGER	table-is-empty(1), table-in-use(2), reset-the-table(3)

echoTestPeriodicTableLastEdit		1.3.6.1.4.1.11.2.3.7.6.1.6.7
The value of sysUpTime at the time of the last edit (create, delete, or modify) to the echoTestPeriodicTable
Status: mandatory	Access: read-only
OBJECT-TYPE
	TimeTicks

echoTestPeriodicTableStatus		1.3.6.1.4.1.11.2.3.7.6.1.6.8
The status of the PeriodicTable. Only those communities with level4 access shall have access to this object. When the agent sets the status of a row in the echoTestPeriodicTable to underCreation, it must set this object to beingModified(4). This object must be reset to valid(1) after the row leaves the underCreation state (either by being set to valid or invalid). The agent should not allow the management station to modify this object when it's value is beingModified(4). The status for any row should be ignored by a manager that has successfully placed the table underRecovery(3). Managers trying to operate on row status during the recovery operation should fail. Management stations which start walking the table after ensuring the table status is valid should ensure the table has remained unchanged during the walk by checking the PeriodicTableLastEdit. A management station cannot set the state to underRecovery(3). To initiate a recovery operation, the management station must set this object to recoveryRequest(2). The agent must clear the table entries when setting this object to recoveryRequest. If successful, the management station may download the echo test table. If unsuccessful, then the contents of the PeriodicTable cannot be guaranteed. The table shall exist in the underRecovery state until the management station has finished downloading the table and sets this object back to valid(1). If the agent determines the table has been in the underRecovery(3) state for an abornmally long time, it may decide that the management station has crashed. The agent then can set the clear the table and set this object to valid(1).
Status: mandatory	Access: read-write
OBJECT-TYPE
	INTEGER	valid(1), recoveryRequest(2), underRecovery(3), beingModified(4)

echoTestNovellDefaultGateway		1.3.6.1.4.1.11.2.3.7.6.1.6.9
The MAC level address of the router through which Novell Echo packets are to be forwarded, if the echo test is to be performed outside of the subnet on which this probe is placed.
Status: mandatory	Access: read-write
OBJECT-TYPE
	OCTET STRING

echotestStatus		1
The SNMP trap that is generated when a LanProbe echo test status has changed and generates an event that is configured for sending SNMP traps.
TRAP-TYPE

duplicateIP		2
The SNMP trap that is generated when the monitor detects a network level address is being used by two different hosts.
TRAP-TYPE

changedIP		3
The SNMP trap that is generated when the monitor detects a host has changed the network level address it is using.
TRAP-TYPE