POWERHUB-CORE-MIB

File: POWERHUB-CORE-MIB.mib (115287 bytes)

Imported modules

RFC1155-SMI RFC-1215 RFC1213-MIB

Imported symbols

enterprises OBJECT-TYPE NetworkAddress
IpAddress Counter Gauge
TimeTicks TRAP-TYPE DisplayString
PhysAddress

Defined Types

MacAddress  
OCTET STRING Size(6)    

AlSlotEntry  
SEQUENCE    
  alSlotNumber INTEGER
  alSlotCardType INTEGER
  alSlotStatus INTEGER
  alSlotModel DisplayString
  alSlotRevision DisplayString
  alSlotIssue DisplayString
  alSlotDeviation DisplayString
  alSlotSerialNumber DisplayString
  alSlotPower5 INTEGER
  alSlotPower12 INTEGER
  alSlotPower33 INTEGER
  alSlotPowerOther INTEGER

AlVportEntry  
SEQUENCE    
  alVportNumber INTEGER
  alVportSlotNumber INTEGER
  alVportPortNumber INTEGER
  alVportPortType INTEGER
  alVportStatus INTEGER
  alVportControllerType INTEGER
  alVportDataRateConfig INTEGER
  alVportOperModeConfig INTEGER
  alVportAutoNegotiateConfig INTEGER
  alVportDataRateStatus INTEGER
  alVportOperModeStatus INTEGER

AlSlotVportEntry  
SEQUENCE    
  alSlotVportSlotNumber INTEGER
  alSlotVportPortNumber INTEGER
  alSlotVportNumber INTEGER
  alSlotVportPortType INTEGER
  alSlotVportStatus INTEGER
  alSlotVportControllerType INTEGER
  alSlotVportDataRateConfig INTEGER
  alSlotVportOperModeConfig INTEGER
  alSlotVportAutoNegotiateConfig INTEGER
  alSlotVportDataRateStatus INTEGER
  alSlotVportOperModeStatus INTEGER

AlPSEntry  
SEQUENCE    
  alPSNumber INTEGER
  alPSStatus INTEGER

AlBridgeEntry  
SEQUENCE    
  alBridgeEntryAddress MacAddress
  alBridgeEntryPort INTEGER
  alBridgeEntryLink INTEGER
  alBridgeEntryRule INTEGER
  alBridgeEntryFlags INTEGER

PortStatsEntry  
SEQUENCE    
  portStatsPort INTEGER
  portStatsPktsIn Counter
  portStatsPktsOut Counter
  portStatsOctetsIn Counter
  portStatsOctetsOut Counter
  portStatsMulticastPktsIn Counter
  portStatsMulticastPktsOut Counter
  portStatsTableMisses Counter
  portStatsRcvBuffErrs Counter
  portStatsXmitBuffErrs Counter
  portStatsTotalCollisions Counter
  portStatsRcvCollisions Counter
  portStatsXmitCollisions Counter
  portStatsXmitQLen Counter
  portStatsPeakUtilization Counter
  portStatsCurrUtilization Counter
  portStatsLossOfCarrier Counter
  portStatsExcessRetries Counter

PortToPortEntry  
SEQUENCE    
  alPPSourcePort INTEGER
  alPPDestinationPort INTEGER
  portToPortPackets INTEGER
  portToPortOctets INTEGER

PortConfigEntry  
SEQUENCE    
  portConfigPort INTEGER
  portConfigSrcRule INTEGER
  portConfigDstRule INTEGER
  portConfigBlockLearnedEntries INTEGER

BrTemplateEntry  
SEQUENCE    
  brTemplateNumber INTEGER
  brTemplateOffset INTEGER
  brTemplateMask DisplayString
  brTemplateComparator DisplayString
  brTemplateOption INTEGER

BrRuleEntry  
SEQUENCE    
  brRuleNumber INTEGER
  brRuleStatement DisplayString

AlBrRuleToNodeEntry  
SEQUENCE    
  brRuleToNodePort INTEGER
  brRuleToNodeMacAddr PhysAddress
  brRuleToNodeRule INTEGER

AlBrGroupEntry  
SEQUENCE    
  brGroupNumber INTEGER
  brGroupPortsMask DisplayString
  brGroupName DisplayString

PortStateEntry  
SEQUENCE    
  portStatePort INTEGER
  portStateDiag INTEGER
  portStateMgmt INTEGER
  portStateStp INTEGER
  portStatePortName DisplayString

AutoPortStateEntry  
SEQUENCE    
  autoPortStatePort INTEGER
  autoPortState INTEGER
  autoPortStateThreshold INTEGER

LinkStatsEntry  
SEQUENCE    
  linkStatsPort INTEGER
  linkStatsLink Counter
  linkStatsPktsIn Counter
  linkStatsOctetsIn Counter
  linkStatsBMCastPktsIn Counter
  linkStatsGiantPkts Counter
  linkStatsFrameErrs Counter
  linkStatsFCSErrs Counter
  linkStatsCodingErrors Counter
  linkStatsDataRateMismatch Counter
  linkStatsJabbers Counter
  linkStatsShortEvents Counter
  linkStatsRunts Counter
  linkStatsPortCollision Counter
  linkStatsLateCollision Counter
  linkStatsAutoPartition Counter
  linkStatsIsolates Counter
  linkStatsSaFieldChanges Counter
  linkStatsLastSa MacAddress

LinkControlEntry  
SEQUENCE    
  linkControlPort INTEGER
  linkControlLink INTEGER
  linkControlEnlState INTEGER
  linkControlLinkTest INTEGER
  linkControlPartition INTEGER
  linkControlPolarity INTEGER

PortLinkEntry  
SEQUENCE    
  portLinkPort INTEGER
  portLinkType INTEGER

FiberStatsEntry  
SEQUENCE    
  fiberStatsPort INTEGER
  fiberAuiStatus INTEGER
  fiberSecurityViolation INTEGER

PortMonitorEntry  
SEQUENCE    
  portMonSrcPort INTEGER
  portMonDstPort INTEGER
  portMonTrafficType INTEGER

PortMonitorViewEntry  
SEQUENCE    
  portMonViewSrcPort INTEGER
  portMonViewDstPort INTEGER
  portMonViewMonitorPort DisplayString

Defined Values

fore 1.3.6.1.4.1.326
OBJECT IDENTIFIER    

systems 1.3.6.1.4.1.326.2
OBJECT IDENTIFIER    

lsd 1.3.6.1.4.1.326.2.6
OBJECT IDENTIFIER    

lsdproducts 1.3.6.1.4.1.326.2.6.1
OBJECT IDENTIFIER    

lsdcommon 1.3.6.1.4.1.326.2.6.2
OBJECT IDENTIFIER    

powerhub4k6k7k 1.3.6.1.4.1.326.2.6.1.1
OBJECT IDENTIFIER    

powerbits 1.3.6.1.4.1.326.2.6.1.2
OBJECT IDENTIFIER    

asn9000 1.3.6.1.4.1.326.2.6.1.3
OBJECT IDENTIFIER    

alchassis 1.3.6.1.4.1.326.2.6.1.1.1
OBJECT IDENTIFIER    

alsystem 1.3.6.1.4.1.326.2.6.2.1
OBJECT IDENTIFIER    

albridge 1.3.6.1.4.1.326.2.6.2.2
OBJECT IDENTIFIER    

almgmt 1.3.6.1.4.1.326.2.6.2.3
OBJECT IDENTIFIER    

alSlotTable 1.3.6.1.4.1.326.2.6.1.1.1.1
A table that contains information about each slot in the PowerHub 4k6k7k chassis.
Status: mandatory Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    AlSlotEntry

alSlotEntry 1.3.6.1.4.1.326.2.6.1.1.1.1.1
Information about a specific slot.
Status: mandatory Access: not-accessible
OBJECT-TYPE    
  AlSlotEntry  

alSlotNumber 1.3.6.1.4.1.326.2.6.1.1.1.1.1.1
The slot number for which the following information applies.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER  

alSlotCardType 1.3.6.1.4.1.326.2.6.1.1.1.1.1.2
The card type for this slot.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER ph7-universalethernet(1), ph7-utp4x4(2), ph7-utp4x6(3), ph7-fddidualdas(4), ph7-fddisingledas(5), ph7-utp16x1(6), ph7-utp13x1(7), ph7-fddidualuniversal(8), ph7-fddisingleuniversal(9), ph7-fddiconcentrator(10), ph7-cddiconcentrator(11), ph4k6k-FL6x1(12), ph4k6k-utp12x1(13), ph4k6k-fddisingledas(14), ph4k6k-ethernet100TX(15), ph4k6k-ethernet100dualTX(16), ph4k6k-ethernet100FXTX(17), ph4k6k-ethernet100FXFX(18), ph4k6k-ethernet100FX(19), ph4k6k-ethernet24x1(20), ph4k6k-ethernet12x1FL(21), ph4k6k-ethernet6x1FL(22), ph4-tenbt-utp(23), ph7-powercell700(24), ph7-6x1fastethernet(25), ph7-10x1FL(26), ph6-powercell600(27), ph7-2x8fastethernet(28), ph7-packetengine1(29), ph7-packetengine2(30)  

alSlotStatus 1.3.6.1.4.1.326.2.6.1.1.1.1.1.3
The status of the card in this slot.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER notequipped(1), notpresent(2), presentequipped(3)  

alSlotModel 1.3.6.1.4.1.326.2.6.1.1.1.1.1.4
The model number for this card.
Status: mandatory Access: read-only
OBJECT-TYPE    
  DisplayString  

alSlotRevision 1.3.6.1.4.1.326.2.6.1.1.1.1.1.5
The revision number for this card.
Status: mandatory Access: read-only
OBJECT-TYPE    
  DisplayString  

alSlotIssue 1.3.6.1.4.1.326.2.6.1.1.1.1.1.6
The issue number for this slot.
Status: mandatory Access: read-only
OBJECT-TYPE    
  DisplayString  

alSlotDeviation 1.3.6.1.4.1.326.2.6.1.1.1.1.1.7
The deviation for this slot.
Status: mandatory Access: read-only
OBJECT-TYPE    
  DisplayString  

alSlotSerialNumber 1.3.6.1.4.1.326.2.6.1.1.1.1.1.8
The serial number of this card this slot.
Status: mandatory Access: read-only
OBJECT-TYPE    
  DisplayString  

alSlotPower5 1.3.6.1.4.1.326.2.6.1.1.1.1.1.9
The number of milliamps. of current drawn by this slot at 5 Volts.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER  

alSlotPower12 1.3.6.1.4.1.326.2.6.1.1.1.1.1.10
The number of milliamps. of current drawn by this slot at 12 Volts.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER  

alSlotPower33 1.3.6.1.4.1.326.2.6.1.1.1.1.1.11
The number of milliamps. of current drawn by this slot at 3.3 Volts.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER  

alSlotPowerOther 1.3.6.1.4.1.326.2.6.1.1.1.1.1.12
The number of milliamps. of current drawn by this slot at OTHER voltage.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER  

alVportTable 1.3.6.1.4.1.326.2.6.1.1.1.2
A table that contains information about each virtual port in the PowerHub 4k6k7k chassis. This table differs from the alSlotToVportTable mainly in how this table is indexed.
Status: mandatory Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    AlVportEntry

alVportEntry 1.3.6.1.4.1.326.2.6.1.1.1.2.1
Information about a specific virtual port.
Status: mandatory Access: not-accessible
OBJECT-TYPE    
  AlVportEntry  

alVportNumber 1.3.6.1.4.1.326.2.6.1.1.1.2.1.1
The virtual port number for which the following information applies.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER  

alVportSlotNumber 1.3.6.1.4.1.326.2.6.1.1.1.2.1.2
The slot number which holds the physical port that corresponds to the virtual port of interest.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER  

alVportPortNumber 1.3.6.1.4.1.326.2.6.1.1.1.2.1.3
The physical port number on the slot that corresponds to this virtual port number, identified by alVportNumber.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER  

alVportPortType 1.3.6.1.4.1.326.2.6.1.1.1.2.1.4
The port type for this virtual port.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER bnc(1), fiber(2), aui(3), mauHdx(4), mauFdx(5), fb(6), notstuffed(7), fddiMMMM(8), fddiMMSM(9), fddiMMLC(10), fddiMMUTP(11), fddiMMEMPTY(12), fddiSMMM(13), fddiSMSM(14), fddiSMLC(15), fddiSMUTP(16), fddiSMEMPTY(17), fddiLCMM(18), fddiLCSM(19), fddiLCLC(20), fddiLCUTP(21), fddiLCEMPTY(22), fddiUTPMM(23), fddiUTPSM(24), fddiUTPLC(25), fddiUTPUTP(26), fddiUTPEMPTY(27), fddiEMPTYEMPTY(28), fddiEMPTYMM(29), fddiEMPTYSM(30), fddiEMPTYLC(31), fddiEMPTYUTP(32), fx100base(33), fasteth100fx(34), fasteth100tx(35), atm(36), utp(37), ds3-utp(38), ds3-stp(39), ds3-vmf(40), ds3-lmf(41), ds3-mf(42), ds3-sf(43), ds3-cx(44), e3-utp(45), e3-stp(46), e3-vmf(47), e3-lmf(48), e3-mf(49), e3-sf(50), e3-cx(51), oc3-utp(52), oc3-stp(53), oc3-vmf(54), oc3-lmf(55), oc3-mf(56), oc3-sf(57), oc3-cx(58), oc12-utp(59), oc12-stp(60), oc12-vmf(61), oc12-lmf(62), oc12-mf(63), oc12-sf(64), oc12-cx(65), fema-10-100(66)  

alVportStatus 1.3.6.1.4.1.326.2.6.1.1.1.2.1.5
The port status for this virtual port.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER bad(1), removed(2), good(3)  

alVportControllerType 1.3.6.1.4.1.326.2.6.1.1.1.2.1.6
The controller type for this virtual port.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER  

alVportDataRateConfig 1.3.6.1.4.1.326.2.6.1.1.1.2.1.7
The data rate requested for this virtual port.
Status: mandatory Access: read-write
OBJECT-TYPE    
  INTEGER none(1), speed10Mbps(2), speed100Mbps(3)  

alVportOperModeConfig 1.3.6.1.4.1.326.2.6.1.1.1.2.1.8
The operating mode requested for this virtual port.
Status: mandatory Access: read-write
OBJECT-TYPE    
  INTEGER none(1), normal(2), halfDuplex(3), fullDuplex(4), loopback(5), fullLoopback(6), decLoopback(7)  

alVportAutoNegotiateConfig 1.3.6.1.4.1.326.2.6.1.1.1.2.1.9
The auto-negotiation requested for this virtual port.
Status: mandatory Access: read-write
OBJECT-TYPE    
  INTEGER none(1), on(2), off(3)  

alVportDataRateStatus 1.3.6.1.4.1.326.2.6.1.1.1.2.1.10
The actual data rate for this virtual port.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER undetermined(1), speed10Mbps(2), speed100Mbps(3)  

alVportOperModeStatus 1.3.6.1.4.1.326.2.6.1.1.1.2.1.11
The actual operating mode for this virtual port.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER undetermined(1), halfDuplex(2), fullDuplex(3), loopback(4)  

alSlotToVportTable 1.3.6.1.4.1.326.2.6.1.1.1.3
A table that contains information about each port of each slot in the PowerHub 4k6k7k chassis. This table is established as a way to specify the information about a physical port located on a slot in the PowerHub 4k6k7k chassis. This table a slot and port number scheme. This table differs from uses two indices (the slot number and the port number) to identify a port.
Status: mandatory Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    AlSlotVportEntry

alSlotVportEntry 1.3.6.1.4.1.326.2.6.1.1.1.3.1
Information about a specific port in a specific slot. The slot number and the port number in that slot (numbered left to right in ascending order) identifies a specific port.
Status: mandatory Access: not-accessible
OBJECT-TYPE    
  AlSlotVportEntry  

alSlotVportSlotNumber 1.3.6.1.4.1.326.2.6.1.1.1.3.1.1
The slot number which holds the port of interest.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER  

alSlotVportPortNumber 1.3.6.1.4.1.326.2.6.1.1.1.3.1.2
The physical port number on a slot which represents the port of interest. The physical port is numbered from left to right in a slot.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER  

alSlotVportNumber 1.3.6.1.4.1.326.2.6.1.1.1.3.1.3
The virtual port number which corresponds to the port that is identified by the slot and port number. This scheme thereby relates each virtual port to a slot and physical port tuplet.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER  

alSlotVportPortType 1.3.6.1.4.1.326.2.6.1.1.1.3.1.4
The port type for this port.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER bnc(1), fiber(2), aui(3), mauHdx(4), mauFdx(5), fb(6), notstuffed(7), fddiMMMM(8), fddiMMSM(9), fddiMMLC(10), fddiMMUTP(11), fddiMMEMPTY(12), fddiSMMM(13), fddiSMSM(14), fddiSMLC(15), fddiSMUTP(16), fddiSMEMPTY(17), fddiLCMM(18), fddiLCSM(19), fddiLCLC(20), fddiLCUTP(21), fddiLCEMPTY(22), fddiUTPMM(23), fddiUTPSM(24), fddiUTPLC(25), fddiUTPUTP(26), fddiUTPEMPTY(27), fddiEMPTYEMPTY(28), fddiEMPTYMM(29), fddiEMPTYSM(30), fddiEMPTYLC(31), fddiEMPTYUTP(32), fx100base(33), fasteth100fx(34), fasteth100tx(35), atm(36), utp(37), ds3-utp(38), ds3-stp(39), ds3-vmf(40), ds3-lmf(41), ds3-mf(42), ds3-sf(43), ds3-cx(44), e3-utp(45), e3-stp(46), e3-vmf(47), e3-lmf(48), e3-mf(49), e3-sf(50), e3-cx(51), oc3-utp(52), oc3-stp(53), oc3-vmf(54), oc3-lmf(55), oc3-mf(56), oc3-sf(57), oc3-cx(58), oc12-utp(59), oc12-stp(60), oc12-vmf(61), oc12-lmf(62), oc12-mf(63), oc12-sf(64), oc12-cx(65), fema-10-100(66)  

alSlotVportStatus 1.3.6.1.4.1.326.2.6.1.1.1.3.1.5
The status for this port.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER  

alSlotVportControllerType 1.3.6.1.4.1.326.2.6.1.1.1.3.1.6
The controller type for this port.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER  

alSlotVportDataRateConfig 1.3.6.1.4.1.326.2.6.1.1.1.3.1.7
The data rate requested for this port. The actual data rate may be different from the requested data rate.
Status: mandatory Access: read-write
OBJECT-TYPE    
  INTEGER none(1), speed10Mbps(2), speed100Mbps(3)  

alSlotVportOperModeConfig 1.3.6.1.4.1.326.2.6.1.1.1.3.1.8
The operating mode requested for this port.
Status: mandatory Access: read-write
OBJECT-TYPE    
  INTEGER none(1), normal(2), halfDuplex(3), fullDuplex(4), loopback(5), fullLoopback(6), decLoopback(7)  

alSlotVportAutoNegotiateConfig 1.3.6.1.4.1.326.2.6.1.1.1.3.1.9
The auto-negotiation requested for this port.
Status: mandatory Access: read-write
OBJECT-TYPE    
  INTEGER none(1), on(2), off(3)  

alSlotVportDataRateStatus 1.3.6.1.4.1.326.2.6.1.1.1.3.1.10
The actual data rate for this port.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER undetermined(1), speed10Mbps(2), speed100Mbps(3)  

alSlotVportOperModeStatus 1.3.6.1.4.1.326.2.6.1.1.1.3.1.11
The actual operating mode for this port.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER undetermined(1), halfDuplex(2), fullDuplex(3), loopback(4)  

alPSTable 1.3.6.1.4.1.326.2.6.1.1.1.4
A table that contains information about each power supply in the PowerHub 4k6k7k chassis.
Status: mandatory Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    AlPSEntry

alPSEntry 1.3.6.1.4.1.326.2.6.1.1.1.4.1
Information about a specific power supply.
Status: mandatory Access: not-accessible
OBJECT-TYPE    
  AlPSEntry  

alPSNumber 1.3.6.1.4.1.326.2.6.1.1.1.4.1.1
The power supply number
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER  

alPSStatus 1.3.6.1.4.1.326.2.6.1.1.1.4.1.2
The status of the power supply identified by the instance of alPSNumber.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER powerGood(1), powerPresentButBad(2), powerNotPresent(3), powerIntermittant(4), powerUnknown(5)  

alCpuSlot 1.3.6.1.4.1.326.2.6.1.1.1.5
The slot number in which the packet engine resides
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER  

alSlotChassis 1.3.6.1.4.1.326.2.6.1.1.1.6
The maximum number of slots available in the powerhub. Presently it could either be a 5, 10, or 15 slot chassis. This object is used only for PH7000.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER slots5(1), slots10(2), slots15(3)  

powerFailure 1
The powerFailure trap indicates that powerFailure occured in the particular powersupply unit.
TRAP-TYPE    

boardFailure 2
The boardFailure trap indicates that intelligent card failure occured in the particular slot.
TRAP-TYPE    

alChassisType 1.3.6.1.4.1.326.2.6.2.1.1
The model type of the PowerHub
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER model3100(1), model3200(2), model3300(3), model3500(4), model3401(5), model3402(6), model3403(7), model3404(8), model3405(9), model3406(10), model3407(11), model3410(12), model3411(13), model3412(14), model3420(15), model3421(16), model3422(17), model3423(18), model3424(19), model3425(20), model5001(21), model5002(22), model5003(23), model5004(24), model5005(25), model5006(26), model7000(30), model6000(31), model4000(32), model4100(33), model8000(34)  

alMcpuRtVer 1.3.6.1.4.1.326.2.6.2.1.2
Runtime software version of the motherboard CPU; it is an ASCII string that describes the version as well as the date and time the software was released from the factory.
Status: mandatory Access: read-only
OBJECT-TYPE    
  DisplayString  

alMcpuPromVer 1.3.6.1.4.1.326.2.6.2.1.3
PROM software version of the motherboard CPU; it is an ASCII string that describes the version as well as the date and time the software was released from the factory.
Status: mandatory Access: read-only
OBJECT-TYPE    
  DisplayString  

alFcpuOneRtVer 1.3.6.1.4.1.326.2.6.2.1.4
Runtime software version of F-bus CPU for the first FDDI board.
Status: mandatory Access: read-only
OBJECT-TYPE    
  DisplayString  

alFcpuTwoRtVer 1.3.6.1.4.1.326.2.6.2.1.5
Runtime software version of F-bus CPU for the second FDDI board.
Status: mandatory Access: read-only
OBJECT-TYPE    
  DisplayString  

alFcpuOnePromVer 1.3.6.1.4.1.326.2.6.2.1.6
PROM software version of F-bus CPU for the first FDDI board.
Status: mandatory Access: read-only
OBJECT-TYPE    
  DisplayString  

alFcpuTwoPromVer 1.3.6.1.4.1.326.2.6.2.1.7
PROM software version of F-bus CPU for the second FDDI board.
Status: mandatory Access: read-only
OBJECT-TYPE    
  DisplayString  

alRcpuOneRtVer 1.3.6.1.4.1.326.2.6.2.1.8
Runtime software version of Ring CPU for the first FDDI board.
Status: mandatory Access: read-only
OBJECT-TYPE    
  DisplayString  

alRcpuTwoRtVer 1.3.6.1.4.1.326.2.6.2.1.9
Runtime software version of Ring CPU for the second FDDI board.
Status: mandatory Access: read-only
OBJECT-TYPE    
  DisplayString  

alRcpuOnePromVer 1.3.6.1.4.1.326.2.6.2.1.10
PROM software version of Ring CPU for the first FDDI board.
Status: mandatory Access: read-only
OBJECT-TYPE    
  DisplayString  

alRcpuTwoPromVer 1.3.6.1.4.1.326.2.6.2.1.11
PROM software version of Ring CPU for the second FDDI board.
Status: mandatory Access: read-only
OBJECT-TYPE    
  DisplayString  

alLastLoginFailureTimeDate 1.3.6.1.4.1.326.2.6.2.1.12
Time and date string of the last login session that failed.
Status: mandatory Access: read-only
OBJECT-TYPE    
  DisplayString  

alLastLoginFailureUserId 1.3.6.1.4.1.326.2.6.2.1.13
User id of the last login session that failed.
Status: mandatory Access: read-only
OBJECT-TYPE    
  DisplayString  

alLastLoginFailureReason 1.3.6.1.4.1.326.2.6.2.1.14
Reason code for the last login failure.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER invalidLoginId(1), passwordMismatch(2)  

alLastLoginSourceAddress 1.3.6.1.4.1.326.2.6.2.1.15
Source address of the last login session that failed. The value would be either 'console' or ipaddress string of the telnet session.
Status: mandatory Access: read-only
OBJECT-TYPE    
  DisplayString  

alLoginFailure 1
The login failure trap indicates that the login failed due to some error condition during the login process.
TRAP-TYPE    

alConsoleSyslogLevel 1.3.6.1.4.1.326.2.6.2.1.17
Level which generates a logging messsage for console port commands (telnet, tip, etc.); no messages if set to off(1).
Status: mandatory Access: read-write
OBJECT-TYPE    
  INTEGER off(1), logEmerg(2), logAlert(3), logCrit(4), logErr(5), logWarning(6), logNotice(7), logInfo(8), logDebug(9)  

alSnmpSyslogLevel 1.3.6.1.4.1.326.2.6.2.1.18
Level which generates a logging messsage for snmp induced changes; no messages if set to off(1).
Status: mandatory Access: read-write
OBJECT-TYPE    
  INTEGER off(1), logEmerg(2), logAlert(3), logCrit(4), logErr(5), logWarning(6), logNotice(7), logInfo(8), logDebug(9)  

alIlmiSyslogLevel 1.3.6.1.4.1.326.2.6.2.1.19
Level which generates a logging messsage for ilmi configuration changes; no messages if set to off(1).
Status: mandatory Access: read-write
OBJECT-TYPE    
  INTEGER off(1), logEmerg(2), logAlert(3), logCrit(4), logErr(5), logWarning(6), logNotice(7), logInfo(8), logDebug(9)  

alSyslogHostType 1.3.6.1.4.1.326.2.6.2.1.20
Host which receives syslog messages: notSet(1) if no host is set or becomes unset; local(2) if messages go to console; ip(3) if messages go to a remote host
Status: mandatory Access: read-write
OBJECT-TYPE    
  INTEGER notSet(1), local(2), ip(3)  

alSyslogHostIp 1.3.6.1.4.1.326.2.6.2.1.21
IP address of remote host which receives syslog messages; must be set if alSyslogHost is set to ip.
Status: mandatory Access: read-write
OBJECT-TYPE    
  DisplayString  

alSyslogHostIpFacility 1.3.6.1.4.1.326.2.6.2.1.22
Syslog facility to be assigned to all syslog messages. Default is daemon(1).
Status: mandatory Access: read-write
OBJECT-TYPE    
  INTEGER daemon(1), local0(2), local1(3), local2(4), local3(5), local4(6), local5(7), local6(8), local7(9)  

alBridgeTable 1.3.6.1.4.1.326.2.6.2.2.1
A table that contains information about unicast entries for which the bridge has forwarding and/or filtering information. This information is used by the transparent bridging function in determining how to propagate a received frame.
Status: mandatory Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    AlBridgeEntry

alBridgeEntry 1.3.6.1.4.1.326.2.6.2.2.1.1
Information about a specific unicast MAC address for which the bridge has some forwarding and/or filtering information.
Status: mandatory Access: not-accessible
OBJECT-TYPE    
  AlBridgeEntry  

alBridgeEntryAddress 1.3.6.1.4.1.326.2.6.2.2.1.1.1
The MAC address for which the bridge has forwarding and/or filtering information.
Status: mandatory Access: read-only
OBJECT-TYPE    
  MacAddress  

alBridgeEntryPort 1.3.6.1.4.1.326.2.6.2.2.1.1.2
The port number of the port on which a frame having a source address equal to the value of the corresponding instance of alBridgeEntryAddress has been seen.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER  


alBridgeEntryRule 1.3.6.1.4.1.326.2.6.2.2.1.1.4
The rule number that is applied to packets that are forwarded to or from this address.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER  

alBridgeEntryFlags 1.3.6.1.4.1.326.2.6.2.2.1.1.5
The status of this entry.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER  

alBridgeTblClear 1.3.6.1.4.1.326.2.6.2.2.2
When set, clears the Bridge table.
Status: mandatory Access: read-write
OBJECT-TYPE    
  INTEGER  

alBrFlushCache 1.3.6.1.4.1.326.2.6.2.2.3
When set, flushes the cache.
Status: mandatory Access: read-write
OBJECT-TYPE    
  INTEGER  

alPortStatsTable 1.3.6.1.4.1.326.2.6.2.2.4
Per port statistics
Status: mandatory Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    PortStatsEntry

portStatsEntry 1.3.6.1.4.1.326.2.6.2.2.4.1
Per port statistics entries.
Status: mandatory Access: not-accessible
OBJECT-TYPE    
  PortStatsEntry  

portStatsPort 1.3.6.1.4.1.326.2.6.2.2.4.1.1
Segment for which the statistics collected.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER  

portStatsPktsIn 1.3.6.1.4.1.326.2.6.2.2.4.1.2
Good packets received on the segment. Packets are listed regardless of packet type, or whether the packet is forwarded to another segment. Error packets are not listed.
Status: mandatory Access: read-only
OBJECT-TYPE    
  Counter  

portStatsPktsOut 1.3.6.1.4.1.326.2.6.2.2.4.1.3
Packets transmitted on the segment. This statistic is incremented when a packet is scheduled for transmission, not when it is actually transmitted.
Status: mandatory Access: read-only
OBJECT-TYPE    
  Counter  

portStatsOctetsIn 1.3.6.1.4.1.326.2.6.2.2.4.1.4
Good octets received on the segment. This statistic includes 8 octets per packet to account for the preamble.
Status: mandatory Access: read-only
OBJECT-TYPE    
  Counter  

portStatsOctetsOut 1.3.6.1.4.1.326.2.6.2.2.4.1.5
Octets transmitted from the segment. This statistic is incremented when a packet is scheduled for transmission, not when it is actually transmitted. This statistic includes 8 octets per packet to account for the preamble.
Status: mandatory Access: read-only
OBJECT-TYPE    
  Counter  

portStatsMulticastPktsIn 1.3.6.1.4.1.326.2.6.2.2.4.1.6
Broadcast multicast packets received on the segment. This statistic is incremented for each good broadcast or multicast packet received on the segment.
Status: mandatory Access: read-only
OBJECT-TYPE    
  Counter  

portStatsMulticastPktsOut 1.3.6.1.4.1.326.2.6.2.2.4.1.7
Broadcast multicast packets transmitted from the segment. This statistic is incremented once for each broadcast or multicast packet scheduled for transmission on the segment.
Status: mandatory Access: read-only
OBJECT-TYPE    
  Counter  

portStatsTableMisses 1.3.6.1.4.1.326.2.6.2.2.4.1.8
Packets received that have unknown destination addresses. When address learning is enabled, this statistic is usually incremented only for the first packet transmitted to a workstation or other device connected to the segment. After a reply is received, the device's source address is added to the bridging table.
Status: mandatory Access: read-only
OBJECT-TYPE    
  Counter  

portStatsRcvBuffErrs 1.3.6.1.4.1.326.2.6.2.2.4.1.9
Incremented each time the hub detects an incoming packet but does not have a buffer in which to store the packet.
Status: mandatory Access: read-only
OBJECT-TYPE    
  Counter  

portStatsXmitBuffErrs 1.3.6.1.4.1.326.2.6.2.2.4.1.10
Incremented each time the hub attempts to forward a packet to a busy destination segment whose output buffers all are full.
Status: mandatory Access: read-only
OBJECT-TYPE    
  Counter  

portStatsTotalCollisions 1.3.6.1.4.1.326.2.6.2.2.4.1.11
The total number of collisions detected on the segment while attempting to transmit and receive packets. For FDDI segments, this statistic is always 0.
Status: mandatory Access: read-only
OBJECT-TYPE    
  Counter  

portStatsRcvCollisions 1.3.6.1.4.1.326.2.6.2.2.4.1.12
The number of collisions detected on the segment while listening for incoming packets. This statistic is only available for UTP segments. For segments on other module types, this statistic is always 0.
Status: mandatory Access: read-only
OBJECT-TYPE    
  Counter  

portStatsXmitCollisions 1.3.6.1.4.1.326.2.6.2.2.4.1.13
The number of collisions detected on the segment while attempting to transmit packets. For FDDI segments, this statistic is always 0.
Status: mandatory Access: read-only
OBJECT-TYPE    
  Counter  

portStatsXmitQLen 1.3.6.1.4.1.326.2.6.2.2.4.1.14
The number of outgoing packets in the transmit queue. These packets have been scheduled for transmission, but have not been transmitted yet.
Status: mandatory Access: read-only
OBJECT-TYPE    
  Counter  

portStatsPeakUtilization 1.3.6.1.4.1.326.2.6.2.2.4.1.15
The segment's maximum utilization during a one-second interval since the statistics last were cleared. For Ethernet segments, the current utilization is calculated as follows: Once per second, the current one- second utilization is computed as (total # octets) x (8 bits/octets) / 10 Mb/s. The peak utilization is then set to the maximum of the current one-second utilization and the previous peak utilization. NOTE: Total # octets is all octets transmitted and received on the segment during the previous second, including 8 octets of preamble per packet. The Ethernet rate is 10Mb.
Status: mandatory Access: read-only
OBJECT-TYPE    
  Counter  

portStatsCurrUtilization 1.3.6.1.4.1.326.2.6.2.2.4.1.16
For Ethernet segments, the current utilization is calculated as follows: Once per second, the current one-second utilization is computed as (total # octets) x (8 bits/octets) / 10 Mb/s. NOTE: Total # octets is all octets transmitted and received on the segment during the previous second, including 8 octets of preamble per packet. The Ethernet rate is 10Mb.
Status: mandatory Access: read-only
OBJECT-TYPE    
  Counter  

portStatsLossOfCarrier 1.3.6.1.4.1.326.2.6.2.2.4.1.17
Indicates that an AUI segment has no cable attached, or the cable or transceiver is faulty.
Status: mandatory Access: read-only
OBJECT-TYPE    
  Counter  

portStatsExcessRetries 1.3.6.1.4.1.326.2.6.2.2.4.1.18
Incremented whenever all of 15 attempts to transmit a single packet cause collisions. This can happen in very busy networks, or when no cable is attached to an enabled BNC port.
Status: mandatory Access: read-only
OBJECT-TYPE    
  Counter  

alBridgeStatsClear 1.3.6.1.4.1.326.2.6.2.2.5
When set, clears the statistics for the bridge. When not set, value 0 is returned.
Status: mandatory Access: read-write
OBJECT-TYPE    
  INTEGER  

alBridgePPControl 1.3.6.1.4.1.326.2.6.2.2.6
When set to 3 , disables the port to port collection of the stats; when set to 1, enables the port to port stats collection; when set to 2, clears the port to port stats.
Status: mandatory Access: read-write
OBJECT-TYPE    
  INTEGER enable(1), clear(2), disable(3)  

alPortToPortTable 1.3.6.1.4.1.326.2.6.2.2.7
Statistics for port to port traffic.
Status: mandatory Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    PortToPortEntry

portToPortEntry 1.3.6.1.4.1.326.2.6.2.2.7.1
Statistics for port to port traffic
Status: mandatory Access: not-accessible
OBJECT-TYPE    
  PortToPortEntry  

alPPSourcePort 1.3.6.1.4.1.326.2.6.2.2.7.1.1
Source port number
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER  

alPPDestinationPort 1.3.6.1.4.1.326.2.6.2.2.7.1.2
Destination port number
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER  

portToPortPackets 1.3.6.1.4.1.326.2.6.2.2.7.1.3
Port to port packets.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER  

portToPortOctets 1.3.6.1.4.1.326.2.6.2.2.7.1.4
Port to port octets.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER  

alPortConfigTable 1.3.6.1.4.1.326.2.6.2.2.8
Per port configuration for configuring Source and Destination Rules etc.
Status: mandatory Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    PortConfigEntry

portConfigEntry 1.3.6.1.4.1.326.2.6.2.2.8.1
Per port configuration.
Status: mandatory Access: not-accessible
OBJECT-TYPE    
  PortConfigEntry  

portConfigPort 1.3.6.1.4.1.326.2.6.2.2.8.1.1
The port number for this table entry
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER  

portConfigSrcRule 1.3.6.1.4.1.326.2.6.2.2.8.1.2
Source Rule for the port number identified by the instance of portConfigPort
Status: mandatory Access: read-write
OBJECT-TYPE    
  INTEGER  

portConfigDstRule 1.3.6.1.4.1.326.2.6.2.2.8.1.3
Destination Rule for the port number identified by the instance of portConfigPort
Status: mandatory Access: read-write
OBJECT-TYPE    
  INTEGER  

portConfigBlockLearnedEntries 1.3.6.1.4.1.326.2.6.2.2.8.1.4
When set to True (1), the port identified by the instance of portConfigPort will block the learned entries; if set to False (2) the port will not block the learned entries
Status: mandatory Access: read-write
OBJECT-TYPE    
  INTEGER true(1), false(2)  

alBridgeIpBridging 1.3.6.1.4.1.326.2.6.2.2.9
When set to enable(1), enables the IP bridging and if set to disable(2), disables the IP bridging.
Status: mandatory Access: read-write
OBJECT-TYPE    
  INTEGER enable(1), disable(2)  

alBrTemplateTable 1.3.6.1.4.1.326.2.6.2.2.10
Per template information
Status: mandatory Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    BrTemplateEntry

brTemplateEntry 1.3.6.1.4.1.326.2.6.2.2.10.1
Template entry.
Status: mandatory Access: not-accessible
OBJECT-TYPE    
  BrTemplateEntry  

brTemplateNumber 1.3.6.1.4.1.326.2.6.2.2.10.1.1
The number of the template with which it is identified.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER  

brTemplateOffset 1.3.6.1.4.1.326.2.6.2.2.10.1.2
A displacement, in octets, from the beginning of the packet. This must be a multiple of 4 in the range from 0 to 124 decimal. A value of -1 will delete the entry
Status: mandatory Access: read-write
OBJECT-TYPE    
  INTEGER  

brTemplateMask 1.3.6.1.4.1.326.2.6.2.2.10.1.3
A 4-byte (32-bit) number, normally specified as eight hexadecimal digits (00000000 - ffffffff) Description: The bytes in the mask are numbered from 0 to 3, starting with the high-order byte (big-endian format). Each byte of the mask is ANDed with the octet in the packet at displacement 'offset + i' to form a 4-byte 'masked value'.
Status: mandatory Access: read-write
OBJECT-TYPE    
  DisplayString  

brTemplateComparator 1.3.6.1.4.1.326.2.6.2.2.10.1.4
A 4-byte number, usually specified as eight hexadecimal digits (00000000 - ffffffff) Description: If the masked value defined above equals the comparator, then the template returns a value of 'true'; otherwise, it returns a value of 'false'.
Status: mandatory Access: read-write
OBJECT-TYPE    
  DisplayString  

brTemplateOption 1.3.6.1.4.1.326.2.6.2.2.10.1.5
Setting this value to 0 assume all 32 bits mask and comparator specified; value 1 assume half-word (2 bytes) qunatity; and value 2 assume single-byte quantity.
Status: mandatory Access: read-write
OBJECT-TYPE    
  INTEGER  

alBrRuleTable 1.3.6.1.4.1.326.2.6.2.2.11
Per rule information
Status: mandatory Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    BrRuleEntry

brRuleEntry 1.3.6.1.4.1.326.2.6.2.2.11.1
Rule entry.
Status: mandatory Access: not-accessible
OBJECT-TYPE    
  BrRuleEntry  

brRuleNumber 1.3.6.1.4.1.326.2.6.2.2.11.1.1
A rule number in the range 101-162. You can define up to 62 rules.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER  

brRuleStatement 1.3.6.1.4.1.326.2.6.2.2.11.1.2
Specifies the templates and the logical operators that make up the rule. Rule statements consist of rule numbers joined by the following logical operators: Operator Means... & AND | OR ~ NOT Rule statements are interpreted from left to right. Use parentheses to group expressions. You can use up to eight sets of parentheses to group template numbers and logical operators. The total maximum number of characters, including blanks, is 64.
Status: mandatory Access: read-write
OBJECT-TYPE    
  DisplayString  

alBrRuleToNodeTable 1.3.6.1.4.1.326.2.6.2.2.12
Rules to specific node.
Status: mandatory Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    AlBrRuleToNodeEntry

alBrRuleToNodeEntry 1.3.6.1.4.1.326.2.6.2.2.12.1
Rule node entry.
Status: mandatory Access: not-accessible
OBJECT-TYPE    
  AlBrRuleToNodeEntry  

brRuleToNodePort 1.3.6.1.4.1.326.2.6.2.2.12.1.1
The number of the port for which this rule applies
Status: mandatory Access: read-write
OBJECT-TYPE    
  INTEGER  

brRuleToNodeMacAddr 1.3.6.1.4.1.326.2.6.2.2.12.1.2
The source MAC address
Status: mandatory Access: read-write
OBJECT-TYPE    
  PhysAddress  

brRuleToNodeRule 1.3.6.1.4.1.326.2.6.2.2.12.1.3
The rule number that applies to this entry.
Status: mandatory Access: read-write
OBJECT-TYPE    
  INTEGER  

alBrGroupTable 1.3.6.1.4.1.326.2.6.2.2.13
Bridge group table.
Status: mandatory Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    AlBrGroupEntry

alBrGroupEntry 1.3.6.1.4.1.326.2.6.2.2.13.1
Bridge group entry.
Status: mandatory Access: not-accessible
OBJECT-TYPE    
  AlBrGroupEntry  

brGroupNumber 1.3.6.1.4.1.326.2.6.2.2.13.1.1
The group number by which the group is identified with.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER  

brGroupPortsMask 1.3.6.1.4.1.326.2.6.2.2.13.1.2
The ports associated with the group number identified by the instance of brGroupNumber. The mask is ascii segments separated by commas. A value of -1 would invalidate the appropriate group.
Status: mandatory Access: read-write
OBJECT-TYPE    
  DisplayString  

brGroupName 1.3.6.1.4.1.326.2.6.2.2.13.1.3
The name of the group for which this entry applies
Status: mandatory Access: read-write
OBJECT-TYPE    
  DisplayString  

alBridgeSTPControl 1.3.6.1.4.1.326.2.6.2.2.14
When set to 2 , disables the spanning tree. set to 1, enables the spanning tree.
Status: mandatory Access: read-write
OBJECT-TYPE    
  INTEGER enable(1), disable(2)  

alPortStateTable 1.3.6.1.4.1.326.2.6.2.2.15
Per port state information about spanning tree, dignostics and management.
Status: mandatory Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    PortStateEntry

portStateEntry 1.3.6.1.4.1.326.2.6.2.2.15.1
Port state entry.
Status: mandatory Access: not-accessible
OBJECT-TYPE    
  PortStateEntry  

portStatePort 1.3.6.1.4.1.326.2.6.2.2.15.1.1
The port number for this table entry
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER  

portStateDiag 1.3.6.1.4.1.326.2.6.2.2.15.1.2
The diagnostics state of the port
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER good(1), bad(2), unknown(3)  

portStateMgmt 1.3.6.1.4.1.326.2.6.2.2.15.1.3
The management state of the port
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER enabled(1), disabled(2)  

portStateStp 1.3.6.1.4.1.326.2.6.2.2.15.1.4
The spanning tree state of the port.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER  

portStatePortName 1.3.6.1.4.1.326.2.6.2.2.15.1.5
The name of this port
Status: mandatory Access: read-only
OBJECT-TYPE    
  DisplayString  

alAutoPortStateTable 1.3.6.1.4.1.326.2.6.2.3.1
auto port stat table
Status: mandatory Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    AutoPortStateEntry

autoportStateEntry 1.3.6.1.4.1.326.2.6.2.3.1.1
auto port stat entry.
Status: mandatory Access: not-accessible
OBJECT-TYPE    
  AutoPortStateEntry  

autoPortStatePort 1.3.6.1.4.1.326.2.6.2.3.1.1.1
The port number for this table entry
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER  

autoPortState 1.3.6.1.4.1.326.2.6.2.3.1.1.2
Whether the auto port state detection is turned on or not.
Status: mandatory Access: read-write
OBJECT-TYPE    
  INTEGER enable(1), disable(2)  

autoPortStateThreshold 1.3.6.1.4.1.326.2.6.2.3.1.1.3
Corresponding to the threshold parameter of the autoportstate command.
Status: mandatory Access: read-write
OBJECT-TYPE    
  INTEGER  

alLinkStatsCollect 1.3.6.1.4.1.326.2.6.2.3.2
When set to enable(1), per link stats collection is enabled; when set to disable(0), the per link stats are not collected.
Status: mandatory Access: read-write
OBJECT-TYPE    
  INTEGER  

alLinkStatsClear 1.3.6.1.4.1.326.2.6.2.3.3
When set, clears the link stats; otherwise value 0 is returned.
Status: mandatory Access: read-write
OBJECT-TYPE    
  INTEGER  

alLinkStatsTable 1.3.6.1.4.1.326.2.6.2.3.4
Per link stats table
Status: mandatory Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    LinkStatsEntry

linkStatsEntry 1.3.6.1.4.1.326.2.6.2.3.4.1
link stats entry.
Status: mandatory Access: read-write
OBJECT-TYPE    
  LinkStatsEntry  

linkStatsPort 1.3.6.1.4.1.326.2.6.2.3.4.1.1
Port Number
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER  


linkStatsPktsIn 1.3.6.1.4.1.326.2.6.2.3.4.1.3
Pkts In - corresponds to pi
Status: mandatory Access: read-only
OBJECT-TYPE    
  Counter  

linkStatsOctetsIn 1.3.6.1.4.1.326.2.6.2.3.4.1.4
Octets In - corresponds to oi
Status: mandatory Access: read-only
OBJECT-TYPE    
  Counter  

linkStatsBMCastPktsIn 1.3.6.1.4.1.326.2.6.2.3.4.1.5
Bmcast Pks In - corresponds to bpi
Status: mandatory Access: read-only
OBJECT-TYPE    
  Counter  

linkStatsGiantPkts 1.3.6.1.4.1.326.2.6.2.3.4.1.6
Giant Pkts - corresponds to gp
Status: mandatory Access: read-only
OBJECT-TYPE    
  Counter  

linkStatsFrameErrs 1.3.6.1.4.1.326.2.6.2.3.4.1.7
Frame Errors - corresponds to fa
Status: mandatory Access: read-only
OBJECT-TYPE    
  Counter  

linkStatsFCSErrs 1.3.6.1.4.1.326.2.6.2.3.4.1.8
FCS Errors corresponds to fcs
Status: mandatory Access: read-only
OBJECT-TYPE    
  Counter  

linkStatsCodingErrors 1.3.6.1.4.1.326.2.6.2.3.4.1.9
This Counter is incremented when the receiver (RX) port detects an invalid symbol in the incoming code sent by the TX port using symbol mode.
Status: mandatory Access: read-only
OBJECT-TYPE    
  Counter  

linkStatsDataRateMismatch 1.3.6.1.4.1.326.2.6.2.3.4.1.10
This counter is incremented by one for each frame received on this port that meets all of the following conditions: 1) The Collision Event signal is not asserted 2) The Activity duration is greater than ValidPacketMinTime 3) The frequency (data rate) is detectably mismatched from the local transmit frequency
Status: mandatory Access: read-only
OBJECT-TYPE    
  Counter  

linkStatsJabbers 1.3.6.1.4.1.326.2.6.2.3.4.1.11
This Counter is incremented for each CarrierEvent on this port whose ActivityDuration is greater than the MAU Jabber Lockup Protection timer
Status: mandatory Access: read-only
OBJECT-TYPE    
  Counter  

linkStatsShortEvents 1.3.6.1.4.1.326.2.6.2.3.4.1.12
This counter is incremented for each CarrierEvent on this port with ActivityDuration less than ShortEventMaxTime.
Status: mandatory Access: read-only
OBJECT-TYPE    
  Counter  

linkStatsRunts 1.3.6.1.4.1.326.2.6.2.3.4.1.13
An event whose length is greater than 74 bit times but less than 82 bit times shall increment either the shortEvents counter or the runts counter but not both
Status: mandatory Access: read-only
OBJECT-TYPE    
  Counter  

linkStatsPortCollision 1.3.6.1.4.1.326.2.6.2.3.4.1.14
This counter is incremented for any CarrierEvent signal on any port for which the CollisionEvent signal on this port is also asserted.
Status: mandatory Access: read-only
OBJECT-TYPE    
  Counter  

linkStatsLateCollision 1.3.6.1.4.1.326.2.6.2.3.4.1.15
This counter is incremented for each CarrierEvent on this port in which the CollIn(X) variable transitions to the value SQE while the ActivityDuration is greater than the LAteEventThreshold.
Status: mandatory Access: read-only
OBJECT-TYPE    
  Counter  

linkStatsAutoPartition 1.3.6.1.4.1.326.2.6.2.3.4.1.16
This counter is incremented each time the repeater has automatically partitioned this port
Status: mandatory Access: read-only
OBJECT-TYPE    
  Counter  

linkStatsIsolates 1.3.6.1.4.1.326.2.6.2.3.4.1.17
This counter is incremented whenever the port detects two consecutive carrier integrity false carriers.
Status: mandatory Access: read-only
OBJECT-TYPE    
  Counter  

linkStatsSaFieldChanges 1.3.6.1.4.1.326.2.6.2.3.4.1.18
This counter is incremented for each time that the rptrAddrTrackLastSourceAddress attribute for this port has changed.
Status: mandatory Access: read-only
OBJECT-TYPE    
  Counter  

linkStatsLastSa 1.3.6.1.4.1.326.2.6.2.3.4.1.19
This object is the SourceAddress of the last readable frame received by this port.
Status: mandatory Access: read-only
OBJECT-TYPE    
  MacAddress  

alLinkControlTable 1.3.6.1.4.1.326.2.6.2.3.5
Per link stats table
Status: mandatory Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    LinkControlEntry

linkControlEntry 1.3.6.1.4.1.326.2.6.2.3.5.1
link control entry.
Status: mandatory Access: read-write
OBJECT-TYPE    
  LinkControlEntry  

linkControlPort 1.3.6.1.4.1.326.2.6.2.3.5.1.1
Port number for this entry.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER  


linkControlEnlState 1.3.6.1.4.1.326.2.6.2.3.5.1.3
Setting the value of this object to Enable (1) will enable the link and setting to Disable(2) will disable the link.
Status: mandatory Access: read-write
OBJECT-TYPE    
  INTEGER enable(1), disable(2)  

linkControlLinkTest 1.3.6.1.4.1.326.2.6.2.3.5.1.4
Link test status for the link; corresponds to lt option of the lkd command.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER  

linkControlPartition 1.3.6.1.4.1.326.2.6.2.3.5.1.5
Partitioning state of the link
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER  

linkControlPolarity 1.3.6.1.4.1.326.2.6.2.3.5.1.6
Polarity of the link
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER  

alPortLinkTable 1.3.6.1.4.1.326.2.6.2.3.6
Per port link type
Status: mandatory Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    PortLinkEntry

portLinkEntry 1.3.6.1.4.1.326.2.6.2.3.6.1
port link entry.
Status: mandatory Access: not-accessible
OBJECT-TYPE    
  PortLinkEntry  

portLinkPort 1.3.6.1.4.1.326.2.6.2.3.6.1.1
The port number for which the port type is to be set
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER  

portLinkType 1.3.6.1.4.1.326.2.6.2.3.6.1.2
The type of port
Status: mandatory Access: read-write
OBJECT-TYPE    
  INTEGER aui(1), bnc(2), bnct(3), utp(4), fiber(5), unknown(6)  

alFiberStatsTable 1.3.6.1.4.1.326.2.6.2.3.7
Per port fiber stats and Fiber Security
Status: mandatory Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    FiberStatsEntry

fiberStatsEntry 1.3.6.1.4.1.326.2.6.2.3.7.1
fiber stat entry.
Status: mandatory Access: not-accessible
OBJECT-TYPE    
  FiberStatsEntry  

fiberStatsPort 1.3.6.1.4.1.326.2.6.2.3.7.1.1
The fiber port for which the stats are requested or the Fiber violation is set
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER  

fiberAuiStatus 1.3.6.1.4.1.326.2.6.2.3.7.1.2
The fiber aui status for the port that is specified by the instance of fiberStatsPort
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER  

fiberSecurityViolation 1.3.6.1.4.1.326.2.6.2.3.7.1.3
The fiber port for which the stats are requested or the Fiber violation is set
Status: mandatory Access: read-write
OBJECT-TYPE    
  INTEGER detect(1), ignore(2), clear(3)  

alPortMonitorClose 1.3.6.1.4.1.326.2.6.2.3.8
Setting the value to close(1), will turn the port monitoring off.
Status: mandatory Access: read-write
OBJECT-TYPE    
  INTEGER  

alPortMonitorTable 1.3.6.1.4.1.326.2.6.2.3.9
port monitor table.
Status: mandatory Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    PortMonitorEntry

portMonitorEntry 1.3.6.1.4.1.326.2.6.2.3.9.1
port monitor entry.
Status: mandatory Access: not-accessible
OBJECT-TYPE    
  PortMonitorEntry  

portMonSrcPort 1.3.6.1.4.1.326.2.6.2.3.9.1.1
The traffic to/from this port will be monitored on the portMonDstPort
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER  

portMonDstPort 1.3.6.1.4.1.326.2.6.2.3.9.1.2
The traffic to/from portMonSrcPort will be monitored on this port
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER  

portMonTrafficType 1.3.6.1.4.1.326.2.6.2.3.9.1.3
Setting this value to 1, will let the port monitor monitor forwarded traffic; setting to 8 means the forwarded traffic will not be monitored.
Status: mandatory Access: read-write
OBJECT-TYPE    
  INTEGER forwarded(1), incoming(2), forwardedandincoming(3), generated(4), forwardedandgenerated(5), incomingandgenerated(6), all(7), stopmonitoring(8)  

alReboot 1.3.6.1.4.1.326.2.6.2.3.10
Setting the value to Reboot(1), will reboot the PowerHub.
Status: mandatory Access: write-only
OBJECT-TYPE    
  INTEGER  

alPortMonitorViewTable 1.3.6.1.4.1.326.2.6.2.3.11
port monitor view table.
Status: mandatory Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    PortMonitorViewEntry

portMonitorViewEntry 1.3.6.1.4.1.326.2.6.2.3.11.1
port monitor view entry.
Status: mandatory Access: not-accessible
OBJECT-TYPE    
  PortMonitorViewEntry  

portMonViewSrcPort 1.3.6.1.4.1.326.2.6.2.3.11.1.1
The traffic from this port to the port designated by portMonViewDstPort will be monitored on portMonViewMonitorPort.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER  

portMonViewDstPort 1.3.6.1.4.1.326.2.6.2.3.11.1.2
The traffic to this port from the port designated by portMonViewSrcPort will be monitored on portMonViewMonitorPort.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER  

portMonViewMonitorPort 1.3.6.1.4.1.326.2.6.2.3.11.1.3
The traffic to portMonViewDstPort from the port designated by portMonViewSrcPort will be monitored on portMonViewMonitorPort. The mask is ascii, segments separated by commas.
Status: mandatory Access: read-write
OBJECT-TYPE    
  DisplayString  

alCfgLocalMediaScope 1.3.6.1.4.1.326.2.6.2.3.12
This object display the types of local media currently available on the PH for storing files. The PH4000 and PH6000 do not support floppy whereas the PH3000 and PH5000 do not support flash. The flash is optional on PH6000 & PH7000. All models do support tftpHost save options. Depending on the value of this object, the user can specify the appropriate filename and the media type in other objects for doing the save operation.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER floppy(1), flash(2), floppyAndFlash(3), none(4)  

alCfgMediaName 1.3.6.1.4.1.326.2.6.2.3.13
This object specify the medium name to which the the powerhub will save the configurations. The value 'none' is returned when user have not set the valid save medium. Save operation cannot be performed when value is set to 'none'.
Status: mandatory Access: read-write
OBJECT-TYPE    
  INTEGER floppy(1), flash(2), tftpHost(3), none(4)  

alCfgTftpHostAddr 1.3.6.1.4.1.326.2.6.2.3.14
This object specify the IP address of the tftp host system to which the configs get saved when the object alCfgMediaName is set with value tftpHost(3).
Status: mandatory Access: read-write
OBJECT-TYPE    
  IpAddress  

alCfgFileName 1.3.6.1.4.1.326.2.6.2.3.15
This object specify the configuration filename to which the PH will save the configuration. Depending on the medium (floppy, flash, or tftpHost) in which the saving will be done, the filename have to be set correctly. For example, the filename for floppy and flash medium cannot exceed 8 characters. The filnames can be appended with the optional dot character followed by 3 character extension. The filenames for tftp host should have been pre-created on the host and it should be writable by the PH. All tftp file access restrictions apply.
Status: mandatory Access: read-write
OBJECT-TYPE    
  DisplayString  

alCfgSaveOp 1.3.6.1.4.1.326.2.6.2.3.16
Save config operation can be performed only when this object is set to value '1'. This field returns a dummy value 100 for get operations.
Status: mandatory Access: read-write
OBJECT-TYPE    
  INTEGER  

Generation date: July 28, 2023, 16:18:13, Copyright © 2007 - 2022 - Circitor