PDN-MPE-DSLAM-SYSTEM-MIB

File: PDN-MPE-DSLAM-SYSTEM-MIB.mib (22692 bytes)

Imported modules

SNMPv2-SMI SNMPv2-CONF SNMPv2-TC
SNMP-FRAMEWORK-MIB PDN-TC ENTITY-MIB
PDN-HEADER-MIB PDN-MPE-MIB2-MIB

Imported symbols

NOTIFICATION-TYPE OBJECT-TYPE MODULE-IDENTITY
Integer32 TimeTicks OBJECT-GROUP
NOTIFICATION-GROUP MODULE-COMPLIANCE TruthValue
TEXTUAL-CONVENTION SnmpAdminString ContactState
entPhysicalIndex entPhysicalEntry pdn-mpe
mpeSysObjectID

Defined Types

MpeEntExtAdminStatus  
Values to support the desired state of the entity. These values were selected to correspond to the syntax of the ifAdminStatus in the IF-MIB.
TEXTUAL-CONVENTION    
  INTEGER up(1), down(2), testing(3)  

MpeEntExtOperStatus  
Values to support the current operational state of the entity. These values were selected to correspond to the syntax of the ifOperStatus in the IF-MIB.
TEXTUAL-CONVENTION    
  INTEGER up(1), down(2), testing(3), unknown(4), dormant(5), notPresent(6), reserved1(7)  

MpeEntExtAlarmEntry  
SEQUENCE    
  mpeEntExtAlarm TruthValue

MpeAlarmRelayEntry  
SEQUENCE    
  mpeAlarmRelayState ContactState

MpeEntPhysicalExtEntry  
SEQUENCE    
  mpeEntPhysicalExtUpTime TimeTicks
  mpeEntPhysicalExtLocation SnmpAdminString
  mpeEntPhysicalExtAdminStatus MpeEntExtAdminStatus
  mpeEntPhysicalExtOperStatus MpeEntExtOperStatus

Defined Values

mpe-dslam 1.3.6.1.4.1.1795.2.24.12.24
The mpe dslam MIB. This MIB is written specifically to extend entPhysicalTable.
MODULE-IDENTITY    

mpeSysDevDslamMIBObjects 1.3.6.1.4.1.1795.2.24.12.24.1
OBJECT IDENTIFIER    

mpeSysDevDslamMIBTraps 1.3.6.1.4.1.1795.2.24.12.24.2
OBJECT IDENTIFIER    

mpeEntExtAlarms 1.3.6.1.4.1.1795.2.24.12.24.1.1
OBJECT IDENTIFIER    

mpeAlarmRelay 1.3.6.1.4.1.1795.2.24.12.24.1.2
OBJECT IDENTIFIER    

mpeEntExtMibObjects 1.3.6.1.4.1.1795.2.24.12.24.1.3
OBJECT IDENTIFIER    

mpeSysDevDslamMIBNotifications 1.3.6.1.4.1.1795.2.24.12.24.2.0
OBJECT IDENTIFIER    

mpeEntExtAlarmTable 1.3.6.1.4.1.1795.2.24.12.24.1.1.1
This table lists the alarm states of the objects listed in the entity-MIB entPhysicalTable.
Status: current Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    MpeEntExtAlarmEntry

mpeEntExtAlarmEntry 1.3.6.1.4.1.1795.2.24.12.24.1.1.1.1
An mpeEntExtAlarmTable entry indicates the alarm state of the physical entity.
Status: current Access: not-accessible
OBJECT-TYPE    
  MpeEntExtAlarmEntry  

mpeEntExtAlarm 1.3.6.1.4.1.1795.2.24.12.24.1.1.1.1.1
This variable indicates the alarm state of the physical entity.
Status: current Access: read-only
OBJECT-TYPE    
  TruthValue  

mpeAlarmRelayEquipIndex 1.3.6.1.4.1.1795.2.24.12.24.1.2.1
This variable is the index of the equipment whose alarms are being relayed. It is a integer number starting from 1 until the max number of physical connectors the DSLAM device has to support relay. NOTE: This object has been deprecated. Please consider using the mpeAlarmRelayTable and mpeAlarmRelayInputStateChanged objects.
Status: deprecated Access: accessible-for-notify
OBJECT-TYPE    
  Integer32  

mpeAlarmRelayInputContactState 1.3.6.1.4.1.1795.2.24.12.24.1.2.2
This variable indicates the alarm state of the Input Contact (open/closed). NOTE: This object has been deprecated. Please consider using the mpeAlarmRelayTable and mpeAlarmRelayInputStateChanged objects.
Status: deprecated Access: accessible-for-notify
OBJECT-TYPE    
  ContactState  

mpeAlarmRelayTable 1.3.6.1.4.1.1795.2.24.12.24.1.2.3
This table holds objects that relate to Alarm Relay input or output.
Status: current Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    MpeAlarmRelayEntry

mpeAlarmRelayEntry 1.3.6.1.4.1.1795.2.24.12.24.1.2.3.1
An entry in this table is a sparse augmentation of the entPhysicalEntry. As such, it is indexed by the entPhysicalIndex and not an augmentation of the entPhysicalTable.
Status: current Access: not-accessible
OBJECT-TYPE    
  MpeAlarmRelayEntry  

mpeAlarmRelayState 1.3.6.1.4.1.1795.2.24.12.24.1.2.3.1.1
This object is used to read or write the state an alarm relay input or output.
Status: current Access: read-write
OBJECT-TYPE    
  ContactState  

mpeEntPhysicalExtTable 1.3.6.1.4.1.1795.2.24.12.24.1.3.1
This table contains entity information that is not defined in the standard ENTITY-MIB.
Status: current Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    MpeEntPhysicalExtEntry

mpeEntPhysicalExtEntry 1.3.6.1.4.1.1795.2.24.12.24.1.3.1.1
An entry extends the entPhysicalEntry defined in the ENTITY-MIB.
Status: current Access: not-accessible
OBJECT-TYPE    
  MpeEntPhysicalExtEntry  

mpeEntPhysicalExtUpTime 1.3.6.1.4.1.1795.2.24.12.24.1.3.1.1.1
The time (in hundredths of a second --just like the sysUpTime) since the entity was last re-initialized.
Status: current Access: read-only
OBJECT-TYPE    
  TimeTicks  

mpeEntPhysicalExtLocation 1.3.6.1.4.1.1795.2.24.12.24.1.3.1.1.2
This object allows the manager to enter the location of the physical entity where applicable. For example, in a stack, chassis or units may be in different locations. In this case, it would be logical for the manager to set this object to the location of the associated chassis. Where the location doesn't make sense, it is recommended that the object return a zero-length string.
Status: current Access: read-write
OBJECT-TYPE    
  SnmpAdminString  

mpeEntPhysicalExtAdminStatus 1.3.6.1.4.1.1795.2.24.12.24.1.3.1.1.3
The desired state of the entity.
Status: current Access: read-write
OBJECT-TYPE    
  MpeEntExtAdminStatus  

mpeEntPhysicalExtOperStatus 1.3.6.1.4.1.1795.2.24.12.24.1.3.1.1.4
The current operational state of the entity.
Status: current Access: read-only
OBJECT-TYPE    
  MpeEntExtOperStatus  

mpeCcn 1.3.6.1.4.1.1795.2.24.12.24.2.7
This trap signifies a Configuration change or software upgrade in the xDSL card. This trap is of 'warning' class
Status: current Access: read-only
NOTIFICATION-TYPE    

mpeDeviceFailure 1.3.6.1.4.1.1795.2.24.12.24.2.15
This trap signifies that the sending protocol's device has failed and the failure was not a result of a device test. Note there are no variable bindings for this trap
Status: current Access: read-only
NOTIFICATION-TYPE    

mpeDeviceFailureCleared 1.3.6.1.4.1.1795.2.24.12.24.2.16
This trap signifies that the sending protocol's device has failed but now it is operational. Failure was not a result of a device test.
Status: current Access: read-only
NOTIFICATION-TYPE    

mpeNonSupportedMCC 1.3.6.1.4.1.1795.2.24.12.24.2.20
AN has detected MCC firmware release too low to support this device
Status: current Access: read-only
NOTIFICATION-TYPE    

mpeNonSupportedChassis 1.3.6.1.4.1.1795.2.24.12.24.2.21
AN in slot xx has been installed in a chassis that cannot support one or more of its features.
Status: current Access: read-only
NOTIFICATION-TYPE    

mpeAlarmRelayInputContactStateChanged 1.3.6.1.4.1.1795.2.24.12.24.2.22
This trap signifies that the state of the InputContact Alarm has changed since last time. NOTE: This object has been deprecated. Please consider using the mpeAlarmRelayInputStateChanged notification.
Status: deprecated Access: read-only
NOTIFICATION-TYPE    

mpeEntPhysicalExtEntityCreated 1.3.6.1.4.1.1795.2.24.12.24.2.23
This trap signifies that an instance of this entity has been created in the entPhysicalTable. This trap is generated in addition to the entConfigChange notification defined in RFC2737.
Status: current Access: read-only
NOTIFICATION-TYPE    

mpeEntPhysicalExtEntityDeleted 1.3.6.1.4.1.1795.2.24.12.24.2.24
This trap signifies that an instance of this entity has been deleted from the entPhysicalTable. This trap is generated in addition to the entConfigChange notification defined in RFC2737.
Status: current Access: read-only
NOTIFICATION-TYPE    

mpeEntPhysicalExtEntityChanged 1.3.6.1.4.1.1795.2.24.12.24.2.25
This trap signifies that an instance of this entity has been modified in the entPhysicalTable as a result of a change in any of the objects in that table. This trap is generated in addition to the entConfigChange notification defined in RFC2737.
Status: current Access: read-only
NOTIFICATION-TYPE    

mpeAlarmRelayInputStateChanged 1.3.6.1.4.1.1795.2.24.12.24.2.0.26
This trap signifies that the state of the Alarm Relay Input has changed.
Status: current Access: read-only
NOTIFICATION-TYPE    

mpeFanEntityModuleFailure 1.3.6.1.4.1.1795.2.24.12.24.2.0.27
This trap indicates the failure of the fan module on the device.
Status: current Access: read-only
NOTIFICATION-TYPE    

mpeFanEntityModuleOperational 1.3.6.1.4.1.1795.2.24.12.24.2.0.28
This trap indicates the indicates the fan module on the device is back to operational.
Status: current Access: read-only
NOTIFICATION-TYPE    

mpePowerSourceAFailure 1.3.6.1.4.1.1795.2.24.12.24.2.0.29
This trap indicates that power source A has failed.
Status: current Access: read-only
NOTIFICATION-TYPE    

mpePowerSourceBFailure 1.3.6.1.4.1.1795.2.24.12.24.2.0.30
This trap indicates that power source B has failed.
Status: current Access: read-only
NOTIFICATION-TYPE    

mpePowerSourceAOperational 1.3.6.1.4.1.1795.2.24.12.24.2.0.31
This trap indicates that the power source A is operational. This trap compliments powerSourceAFailure trap.
Status: current Access: read-only
NOTIFICATION-TYPE    

mpePowerSourceBOperational 1.3.6.1.4.1.1795.2.24.12.24.2.0.32
This trap indicates that the power source B is operational. This trap compliments powerSourceBFailure trap.
Status: current Access: read-only
NOTIFICATION-TYPE    

mpeSysDevDslamConformance 1.3.6.1.4.1.1795.2.24.12.24.3
OBJECT IDENTIFIER    

mpeSysDevDslamGroups 1.3.6.1.4.1.1795.2.24.12.24.3.1
OBJECT IDENTIFIER    

mpeSysDevDslamCompliances 1.3.6.1.4.1.1795.2.24.12.24.3.2
OBJECT IDENTIFIER    

mpeSysDevDslamDeprecatedGroup 1.3.6.1.4.1.1795.2.24.12.24.3.3
OBJECT IDENTIFIER    

mpeSysDevDslamAlarmCompliances 1.3.6.1.4.1.1795.2.24.12.24.3.2.1
The compliance statement for entities and their alarms states.
Status: current Access: read-only
MODULE-COMPLIANCE    

mpeSysDevDslamAlarmDeprecatedCompliances 1.3.6.1.4.1.1795.2.24.12.24.3.2.2
The compliance statement for deprecated groups
Status: deprecated Access: read-only
MODULE-COMPLIANCE    

mpeSysDevDslamAlarmStateGroup 1.3.6.1.4.1.1795.2.24.12.24.3.1.1
The collection of objects which are used to describe alarm states for equipments physically connected to a DSLAM device.
Status: current Access: read-only
OBJECT-GROUP    

mpeEntityExtNotificationGroup 1.3.6.1.4.1.1795.2.24.12.24.3.1.2
The collection of objects which are used to notify that trap conditions are met.
Status: current Access: read-only
NOTIFICATION-GROUP    

mpeSysDevDslamAlarmRelayGroup 1.3.6.1.4.1.1795.2.24.12.24.3.1.3
The collection of objects which are used for Alarm Relay objects.
Status: current Access: read-only
OBJECT-GROUP    

mpeEntPhysicalExtGroup 1.3.6.1.4.1.1795.2.24.12.24.3.1.4
The collection of objects which are used in extending the entPhysicalTable.
Status: current Access: read-only
OBJECT-GROUP    

mpeEntPhysicalExtNotificationObjectGroup 1.3.6.1.4.1.1795.2.24.12.24.3.1.5
A collection of objects that are included in the OBJECTS clause of notifications.
Status: current Access: read-only
OBJECT-GROUP    

mpeEntityExtPowerFailureNotificationGroup 1.3.6.1.4.1.1795.2.24.12.24.3.1.6
The collection of objects which are used to notify that trap conditions are met.
Status: current Access: read-only
NOTIFICATION-GROUP    

mpeDslamDeprecatedObjectsGroup 1.3.6.1.4.1.1795.2.24.12.24.3.3.1
The collection of objects that have been deprecated.
Status: deprecated Access: read-only
OBJECT-GROUP    

mpeDslamDeprecatedNotificationsGroup 1.3.6.1.4.1.1795.2.24.12.24.3.3.2
The collection of traps/notifications that have been deprecated.
Status: deprecated Access: read-only
NOTIFICATION-GROUP