PANDATEL-INAX-MODEM-MIB

File: PANDATEL-INAX-MODEM-MIB.mib (45296 bytes)

Imported modules

RFC1155-SMI RFC1213-MIB RFC-1212
PANDATEL-MODEM-MIB

Imported symbols

enterprises Gauge DisplayString
OBJECT-TYPE mdmSpecifics device-id

Defined Types

InaxTableEntry  
SEQUENCE    
  mdmRack INTEGER
  mdmModem INTEGER
  mdmPosition INTEGER
  mdmModemName DisplayString
  mdmModemProperty INTEGER
  mdmActiveLink INTEGER
  mdmRemoteAccessMode INTEGER

InaxIFPortEntry  
SEQUENCE    
  iportRack INTEGER
  iportModem INTEGER
  iportPosition INTEGER
  iportPort INTEGER
  iportDataEmulationMode INTEGER
  iportDataRate INTEGER
  iportTimeslotSize INTEGER

InaxLinePortEntry  
SEQUENCE    
  lportRack INTEGER
  lportModem INTEGER
  lportPosition INTEGER
  lportPort INTEGER
  lportDataEmulationMode INTEGER
  lportClockSource INTEGER
  lportDataRate INTEGER
  lportCRC4Generation INTEGER
  lportFramingMode INTEGER
  lportCodingMode INTEGER
  lportLineBuiltOut INTEGER
  lportPortMode INTEGER
  lportCRC6Test INTEGER
  lportCRC6Status INTEGER
  lportCRC6Error Gauge

InaxTimeslotEntry  
SEQUENCE    
  tsRack INTEGER
  tsModem INTEGER
  tsPosition INTEGER
  tsPort INTEGER
  tsTimeslot1 INTEGER
  tsTimeslot2 INTEGER
  tsTimeslot3 INTEGER
  tsTimeslot4 INTEGER
  tsTimeslot5 INTEGER
  tsTimeslot6 INTEGER
  tsTimeslot7 INTEGER
  tsTimeslot8 INTEGER
  tsTimeslot9 INTEGER
  tsTimeslot10 INTEGER
  tsTimeslot11 INTEGER
  tsTimeslot12 INTEGER
  tsTimeslot13 INTEGER
  tsTimeslot14 INTEGER
  tsTimeslot15 INTEGER
  tsTimeslot16 INTEGER
  tsTimeslot17 INTEGER
  tsTimeslot18 INTEGER
  tsTimeslot19 INTEGER
  tsTimeslot20 INTEGER
  tsTimeslot21 INTEGER
  tsTimeslot22 INTEGER
  tsTimeslot23 INTEGER
  tsTimeslot24 INTEGER
  tsTimeslot25 INTEGER
  tsTimeslot26 INTEGER
  tsTimeslot27 INTEGER
  tsTimeslot28 INTEGER
  tsTimeslot29 INTEGER
  tsTimeslot30 INTEGER
  tsTimeslot31 INTEGER

Defined Values

inax-modem 1.3.6.1.4.1.760.1.1.2.1.10.10000.2.701
OBJECT IDENTIFIER    

inax 1.3.6.1.4.1.760.1.1.2.1.10.701
OBJECT IDENTIFIER    

inaxModemTable 1.3.6.1.4.1.760.1.1.2.1.10.701.1
This table contains information about all INAX units in all racks.
OBJECT-TYPE    
  SEQUENCE OF  
    InaxTableEntry

inaxTableEntry 1.3.6.1.4.1.760.1.1.2.1.10.701.1.1
The index of the table.
OBJECT-TYPE    
  InaxTableEntry  

mdmRack 1.3.6.1.4.1.760.1.1.2.1.10.701.1.1.1
The index of the rack where the unit is installed.
OBJECT-TYPE    
  INTEGER  

mdmModem 1.3.6.1.4.1.760.1.1.2.1.10.701.1.1.2
This entry displays the slot number where the corresponding unit is installed in the rack.
OBJECT-TYPE    
  INTEGER  

mdmPosition 1.3.6.1.4.1.760.1.1.2.1.10.701.1.1.3
This entry displays the location of the corresponding unit: 'local' or 'remote'. The unit which is plugged into a managed rack is 'local', the counterpart is 'remote'.
OBJECT-TYPE    
  INTEGER local(1), remote(2)  

mdmModemName 1.3.6.1.4.1.760.1.1.2.1.10.701.1.1.5
The verbal name of this unit.
OBJECT-TYPE    
  DisplayString  

mdmModemProperty 1.3.6.1.4.1.760.1.1.2.1.10.701.1.1.7
The speed class of the unit: 'e1' or 't1'.
OBJECT-TYPE    
  INTEGER other(1), e1(2), t1(3), unknown(99)  


mdmRemoteAccessMode 1.3.6.1.4.1.760.1.1.2.1.10.701.1.1.64
This entry defines the time slot assigned for remote management. Remote management is realized via port 5 always. For T1 units 24 time slots are available only. The remote unit's configuration changes simultaneously.
OBJECT-TYPE    
  INTEGER via-timeslot-1(1), via-timeslot-2(2), via-timeslot-3(3), via-timeslot-4(4), via-timeslot-5(5), via-timeslot-6(6), via-timeslot-7(7), via-timeslot-8(8), via-timeslot-9(9), via-timeslot-10(10), via-timeslot-11(11), via-timeslot-12(12), via-timeslot-13(13), via-timeslot-14(14), via-timeslot-15(15), via-timeslot-16(16), via-timeslot-17(17), via-timeslot-18(18), via-timeslot-19(19), via-timeslot-20(20), via-timeslot-21(21), via-timeslot-22(22), via-timeslot-23(23), via-timeslot-24(24), via-timeslot-25(25), via-timeslot-26(26), via-timeslot-27(27), via-timeslot-28(28), via-timeslot-29(29), via-timeslot-30(30), via-timeslot-31(31), disable(98), other(99)  

inaxIFPortTable 1.3.6.1.4.1.760.1.1.2.1.10.701.2
This table contains information about all I/F ports of the INAX units in all racks.
OBJECT-TYPE    
  SEQUENCE OF  
    InaxIFPortEntry

inaxIFPortEntry 1.3.6.1.4.1.760.1.1.2.1.10.701.2.1
The index of the table.
OBJECT-TYPE    
  InaxIFPortEntry  

iportRack 1.3.6.1.4.1.760.1.1.2.1.10.701.2.1.1
The index of the rack where the unit is installed.
OBJECT-TYPE    
  INTEGER  

iportModem 1.3.6.1.4.1.760.1.1.2.1.10.701.2.1.2
The index of the INAX unit the port belongs to.
OBJECT-TYPE    
  INTEGER  

iportPosition 1.3.6.1.4.1.760.1.1.2.1.10.701.2.1.3
This entry displays the location of the corresponding port: 'local' or 'remote'. The port which is plugged into a managed rack is 'local', the counterpart is 'remote'.
OBJECT-TYPE    
  INTEGER local(1), remote(2)  

iportPort 1.3.6.1.4.1.760.1.1.2.1.10.701.2.1.4
The index of the port.
OBJECT-TYPE    
  INTEGER  

iportDataEmulationMode 1.3.6.1.4.1.760.1.1.2.1.10.701.2.1.6
Interface mode of the port: 'dte', 'dce', 'te', or 'nt'.
OBJECT-TYPE    
  INTEGER other(1), dte(2), dce(3), te(4), nt(5), unknown(99)  

iportDataRate 1.3.6.1.4.1.760.1.1.2.1.10.701.2.1.25
The data rate at the interface port in bits per seconds.
OBJECT-TYPE    
  INTEGER off(1)  

iportTimeslotSize 1.3.6.1.4.1.760.1.1.2.1.10.701.2.1.27
This entry determines the size of the time slots: 'nx64k' or 'nx56k'. 'nx56k' is valid for T1 units only. The remote unit's configuration changes simultaneously.
OBJECT-TYPE    
  INTEGER other(1), nx64k(2), nx56k(3), not-available(100)  

inaxLinePortTable 1.3.6.1.4.1.760.1.1.2.1.10.701.3
This table contains information about all line ports of the INAX units in all racks.
OBJECT-TYPE    
  SEQUENCE OF  
    InaxLinePortEntry

inaxLinePortEntry 1.3.6.1.4.1.760.1.1.2.1.10.701.3.1
The index of the table.
OBJECT-TYPE    
  InaxLinePortEntry  

lportRack 1.3.6.1.4.1.760.1.1.2.1.10.701.3.1.1
The index of the rack where the unit is installed.
OBJECT-TYPE    
  INTEGER  

lportModem 1.3.6.1.4.1.760.1.1.2.1.10.701.3.1.2
The index of the INAX unit the port belongs to.
OBJECT-TYPE    
  INTEGER  

lportPosition 1.3.6.1.4.1.760.1.1.2.1.10.701.3.1.3
This entry displays the location of the corresponding port: 'local' or 'remote'. The port which is plugged into a managed rack is 'local', the counterpart is 'remote'.
OBJECT-TYPE    
  INTEGER local(1), remote(2)  

lportPort 1.3.6.1.4.1.760.1.1.2.1.10.701.3.1.4
The index of the port.
OBJECT-TYPE    
  INTEGER  

lportDataEmulationMode 1.3.6.1.4.1.760.1.1.2.1.10.701.3.1.6
Interface mode of the port: 'te' or 'nt'.
OBJECT-TYPE    
  INTEGER other(1), dte(2), dce(3), te(4), nt(5), unknown(99)  

lportClockSource 1.3.6.1.4.1.760.1.1.2.1.10.701.3.1.24
The clock source: 'internal' or 'remote'. Port 4 can only be set to 'internal'.
OBJECT-TYPE    
  INTEGER other(1), internal(2), remote(3)  

lportDataRate 1.3.6.1.4.1.760.1.1.2.1.10.701.3.1.25
The data rate at the line port in bits per seconds.
OBJECT-TYPE    
  INTEGER off(1)  

lportCRC4Generation 1.3.6.1.4.1.760.1.1.2.1.10.701.3.1.41
This entry enables or disables the generation of a CRC4 check sum. The remote unit's configuration changes simultaneously. Valid for E1 units only.
OBJECT-TYPE    
  INTEGER other(1), disable(2), enable(3), not-available(100)  

lportFramingMode 1.3.6.1.4.1.760.1.1.2.1.10.701.3.1.50
The T1 framing mode: 'd4' or 'esf'. The remote unit's configuration changes simultaneously. Valid for T1 units only.
OBJECT-TYPE    
  INTEGER other(1), d4(2), esf(3), not-available(100)  

lportCodingMode 1.3.6.1.4.1.760.1.1.2.1.10.701.3.1.51
The T1 coding mode at port 4: 'ami' or 'b8zs'. The remote unit's configuration changes simultaneously. Valid for T1 units only.
OBJECT-TYPE    
  INTEGER other(1), ami(2), b8zs(3), not-available(100)  

lportLineBuiltOut 1.3.6.1.4.1.760.1.1.2.1.10.701.3.1.68
The G.703 transmission mode of the unit.
OBJECT-TYPE    
  INTEGER other(1), itu-rec-g703(2), dsx-1-0to133-ft(3), dsx-1-133to266-ft(4), dsx-1-266to399-ft(5), dsx-1-399to533-ft(6), dsx-1-533to655-ft(7), csu-0db(8), csu-7db5(9), csu-15db(10), csu-22db5(11), not-available(100)  

lportPortMode 1.3.6.1.4.1.760.1.1.2.1.10.701.3.1.69
The operation mode at port 4: 'interface-mode', 'backup-mode', or 'link-mode'.
OBJECT-TYPE    
  INTEGER other(1), if-mode(2), backup-mode(3), link-mode(4)  

lportCRC6Test 1.3.6.1.4.1.760.1.1.2.1.10.701.3.1.100
This entry enables the execution of a CRC6 test. Write requests with values other than 'start' or 'stop' will be rejected. Valid for T1 units only.
OBJECT-TYPE    
  INTEGER other(1), start(3), stop(4), not-available(100)  

lportCRC6Status 1.3.6.1.4.1.760.1.1.2.1.10.701.3.1.101
This entry indicates the status of the CRC6 test. Valid for T1 units only.
OBJECT-TYPE    
  INTEGER other(1), never-started(2), running(5), stopped(6), start-failed(7), not-available(100)  

lportCRC6Error 1.3.6.1.4.1.760.1.1.2.1.10.701.3.1.102
This entry indicates the number of errors detected during the last 60 seconds.
OBJECT-TYPE    
  Gauge  

inaxTimeslotTable 1.3.6.1.4.1.760.1.1.2.1.10.701.4
This table contains information about all line ports of the INAX units in all racks.
OBJECT-TYPE    
  SEQUENCE OF  
    InaxTimeslotEntry

inaxTimeslotEntry 1.3.6.1.4.1.760.1.1.2.1.10.701.4.1
The index of the table.
OBJECT-TYPE    
  InaxTimeslotEntry  

tsRack 1.3.6.1.4.1.760.1.1.2.1.10.701.4.1.1
The index of the rack where the unit is installed.
OBJECT-TYPE    
  INTEGER  

tsModem 1.3.6.1.4.1.760.1.1.2.1.10.701.4.1.2
The index of the INAX unit the port belongs to.
OBJECT-TYPE    
  INTEGER  

tsPosition 1.3.6.1.4.1.760.1.1.2.1.10.701.4.1.3
This entry displays the location of the corresponding port: 'local' or 'remote'. The port which is plugged into a managed rack is 'local', the counterpart is 'remote'.
OBJECT-TYPE    
  INTEGER local(1), remote(2)  

tsPort 1.3.6.1.4.1.760.1.1.2.1.10.701.4.1.4
The index of the port.
OBJECT-TYPE    
  INTEGER  

tsTimeslot1 1.3.6.1.4.1.760.1.1.2.1.10.701.4.1.301
This entry defines the port number used for the transmission of time slot 1. 'port-4' is available only if IportPortmode is set to 'interface-mode'. If the time slot is assigned for remote management (see mdmRemoteAccessMode).
OBJECT-TYPE    
  INTEGER port-1(1), port-2(2), port-3(3), port-4(4), remote-access(97), off(98), other(99), not-available(100)  

tsTimeslot2 1.3.6.1.4.1.760.1.1.2.1.10.701.4.1.302
This entry defines the port number used for the transmission of time slot 2. 'port-4' is available only if IportPortmode is set to 'interface-mode'. If the time slot is assigned for remote management (see mdmRemoteAccessMode).
OBJECT-TYPE    
  INTEGER port-1(1), port-2(2), port-3(3), port-4(4), remote-access(97), off(98), other(99), not-available(100)  

tsTimeslot3 1.3.6.1.4.1.760.1.1.2.1.10.701.4.1.303
This entry defines the port number used for the transmission of time slot 3. 'port-4' is available only if IportPortmode is set to 'interface-mode'. If the time slot is assigned for remote management (see mdmRemoteAccessMode).
OBJECT-TYPE    
  INTEGER port-1(1), port-2(2), port-3(3), port-4(4), remote-access(97), off(98), other(99), not-available(100)  

tsTimeslot4 1.3.6.1.4.1.760.1.1.2.1.10.701.4.1.304
This entry defines the port number used for the transmission of time slot 4. 'port-4' is available only if IportPortmode is set to 'interface-mode'. If the time slot is assigned for remote management (see mdmRemoteAccessMode).
OBJECT-TYPE    
  INTEGER port-1(1), port-2(2), port-3(3), port-4(4), remote-access(97), off(98), other(99), not-available(100)  

tsTimeslot5 1.3.6.1.4.1.760.1.1.2.1.10.701.4.1.305
This entry defines the port number used for the transmission of time slot 5. 'port-4' is available only if IportPortmode is set to 'interface-mode'. If the time slot is assigned for remote management (see mdmRemoteAccessMode).
OBJECT-TYPE    
  INTEGER port-1(1), port-2(2), port-3(3), port-4(4), remote-access(97), off(98), other(99), not-available(100)  

tsTimeslot6 1.3.6.1.4.1.760.1.1.2.1.10.701.4.1.306
This entry defines the port number used for the transmission of time slot 6. 'port-4' is available only if IportPortmode is set to 'interface-mode'. If the time slot is assigned for remote management (see mdmRemoteAccessMode).
OBJECT-TYPE    
  INTEGER port-1(1), port-2(2), port-3(3), port-4(4), remote-access(97), off(98), other(99), not-available(100)  

tsTimeslot7 1.3.6.1.4.1.760.1.1.2.1.10.701.4.1.307
This entry defines the port number used for the transmission of time slot 7. 'port-4' is available only if IportPortmode is set to 'interface-mode'. If the time slot is assigned for remote management (see mdmRemoteAccessMode).
OBJECT-TYPE    
  INTEGER port-1(1), port-2(2), port-3(3), port-4(4), remote-access(97), off(98), other(99), not-available(100)  

tsTimeslot8 1.3.6.1.4.1.760.1.1.2.1.10.701.4.1.308
This entry defines the port number used for the transmission of time slot 8. 'port-4' is available only if IportPortmode is set to 'interface-mode'. If the time slot is assigned for remote management (see mdmRemoteAccessMode).
OBJECT-TYPE    
  INTEGER port-1(1), port-2(2), port-3(3), port-4(4), remote-access(97), off(98), other(99), not-available(100)  

tsTimeslot9 1.3.6.1.4.1.760.1.1.2.1.10.701.4.1.309
This entry defines the port number used for the transmission of time slot 9. 'port-4' is available only if IportPortmode is set to 'interface-mode'. If the time slot is assigned for remote management (see mdmRemoteAccessMode).
OBJECT-TYPE    
  INTEGER port-1(1), port-2(2), port-3(3), port-4(4), remote-access(97), off(98), other(99), not-available(100)  

tsTimeslot10 1.3.6.1.4.1.760.1.1.2.1.10.701.4.1.310
This entry defines the port number used for the transmission of time slot 10. 'port-4' is available only if IportPortmode is set to 'interface-mode'. If the time slot is assigned for remote management (see mdmRemoteAccessMode).
OBJECT-TYPE    
  INTEGER port-1(1), port-2(2), port-3(3), port-4(4), remote-access(97), off(98), other(99), not-available(100)  

tsTimeslot11 1.3.6.1.4.1.760.1.1.2.1.10.701.4.1.311
This entry defines the port number used for the transmission of time slot 11. 'port-4' is available only if IportPortmode is set to 'interface-mode'. If the time slot is assigned for remote management (see mdmRemoteAccessMode).
OBJECT-TYPE    
  INTEGER port-1(1), port-2(2), port-3(3), port-4(4), remote-access(97), off(98), other(99), not-available(100)  

tsTimeslot12 1.3.6.1.4.1.760.1.1.2.1.10.701.4.1.312
This entry defines the port number used for the transmission of time slot 12. 'port-4' is available only if IportPortmode is set to 'interface-mode'. If the time slot is assigned for remote management (see mdmRemoteAccessMode).
OBJECT-TYPE    
  INTEGER port-1(1), port-2(2), port-3(3), port-4(4), remote-access(97), off(98), other(99), not-available(100)  

tsTimeslot13 1.3.6.1.4.1.760.1.1.2.1.10.701.4.1.313
This entry defines the port number used for the transmission of time slot 13. 'port-4' is available only if IportPortmode is set to 'interface-mode'. If the time slot is assigned for remote management (see mdmRemoteAccessMode).
OBJECT-TYPE    
  INTEGER port-1(1), port-2(2), port-3(3), port-4(4), remote-access(97), off(98), other(99), not-available(100)  

tsTimeslot14 1.3.6.1.4.1.760.1.1.2.1.10.701.4.1.314
This entry defines the port number used for the transmission of time slot 14. 'port-4' is available only if IportPortmode is set to 'interface-mode'. If the time slot is assigned for remote management (see mdmRemoteAccessMode).
OBJECT-TYPE    
  INTEGER port-1(1), port-2(2), port-3(3), port-4(4), remote-access(97), off(98), other(99), not-available(100)  

tsTimeslot15 1.3.6.1.4.1.760.1.1.2.1.10.701.4.1.315
This entry defines the port number used for the transmission of time slot 15. 'port-4' is available only if IportPortmode is set to 'interface-mode'. If the time slot is assigned for remote management (see mdmRemoteAccessMode).
OBJECT-TYPE    
  INTEGER port-1(1), port-2(2), port-3(3), port-4(4), remote-access(97), off(98), other(99), not-available(100)  

tsTimeslot16 1.3.6.1.4.1.760.1.1.2.1.10.701.4.1.316
This entry defines the port number used for the transmission of time slot 16. 'port-4' is available only if IportPortmode is set to 'interface-mode'. If the time slot is assigned for remote management (see mdmRemoteAccessMode).
OBJECT-TYPE    
  INTEGER port-1(1), port-2(2), port-3(3), port-4(4), remote-access(97), off(98), other(99), not-available(100)  

tsTimeslot17 1.3.6.1.4.1.760.1.1.2.1.10.701.4.1.317
This entry defines the port number used for the transmission of time slot 17. 'port-4' is available only if IportPortmode is set to 'interface-mode'. If the time slot is assigned for remote management (see mdmRemoteAccessMode).
OBJECT-TYPE    
  INTEGER port-1(1), port-2(2), port-3(3), port-4(4), remote-access(97), off(98), other(99), not-available(100)  

tsTimeslot18 1.3.6.1.4.1.760.1.1.2.1.10.701.4.1.318
This entry defines the port number used for the transmission of time slot 18. 'port-4' is available only if IportPortmode is set to 'interface-mode'. If the time slot is assigned for remote management (see mdmRemoteAccessMode).
OBJECT-TYPE    
  INTEGER port-1(1), port-2(2), port-3(3), port-4(4), remote-access(97), off(98), other(99), not-available(100)  

tsTimeslot19 1.3.6.1.4.1.760.1.1.2.1.10.701.4.1.319
This entry defines the port number used for the transmission of time slot 19. 'port-4' is available only if IportPortmode is set to 'interface-mode'. If the time slot is assigned for remote management (see mdmRemoteAccessMode).
OBJECT-TYPE    
  INTEGER port-1(1), port-2(2), port-3(3), port-4(4), remote-access(97), off(98), other(99), not-available(100)  

tsTimeslot20 1.3.6.1.4.1.760.1.1.2.1.10.701.4.1.320
This entry defines the port number used for the transmission of time slot 20. 'port-4' is available only if IportPortmode is set to 'interface-mode'. If the time slot is assigned for remote management (see mdmRemoteAccessMode).
OBJECT-TYPE    
  INTEGER port-1(1), port-2(2), port-3(3), port-4(4), remote-access(97), off(98), other(99), not-available(100)  

tsTimeslot21 1.3.6.1.4.1.760.1.1.2.1.10.701.4.1.321
This entry defines the port number used for the transmission of time slot 21. 'port-4' is available only if IportPortmode is set to 'interface-mode'. If the time slot is assigned for remote management (see mdmRemoteAccessMode).
OBJECT-TYPE    
  INTEGER port-1(1), port-2(2), port-3(3), port-4(4), remote-access(97), off(98), other(99), not-available(100)  

tsTimeslot22 1.3.6.1.4.1.760.1.1.2.1.10.701.4.1.322
This entry defines the port number used for the transmission of time slot 22. 'port-4' is available only if IportPortmode is set to 'interface-mode'. If the time slot is assigned for remote management (see mdmRemoteAccessMode).
OBJECT-TYPE    
  INTEGER port-1(1), port-2(2), port-3(3), port-4(4), remote-access(97), off(98), other(99), not-available(100)  

tsTimeslot23 1.3.6.1.4.1.760.1.1.2.1.10.701.4.1.323
This entry defines the port number used for the transmission of time slot 23. 'port-4' is available only if IportPortmode is set to 'interface-mode'. If the time slot is assigned for remote management (see mdmRemoteAccessMode).
OBJECT-TYPE    
  INTEGER port-1(1), port-2(2), port-3(3), port-4(4), remote-access(97), off(98), other(99), not-available(100)  

tsTimeslot24 1.3.6.1.4.1.760.1.1.2.1.10.701.4.1.324
This entry defines the port number used for the transmission of time slot 24. 'port-4' is available only if IportPortmode is set to 'interface-mode'. If the time slot is assigned for remote management (see mdmRemoteAccessMode).
OBJECT-TYPE    
  INTEGER port-1(1), port-2(2), port-3(3), port-4(4), remote-access(97), off(98), other(99), not-available(100)  

tsTimeslot25 1.3.6.1.4.1.760.1.1.2.1.10.701.4.1.325
This entry defines the port number used for the transmission of time slot 25. 'port-4' is available only if IportPortmode is set to 'interface-mode'. If the time slot is assigned for remote management (see mdmRemoteAccessMode). Valid for E1 units only.
OBJECT-TYPE    
  INTEGER port-1(1), port-2(2), port-3(3), port-4(4), remote-access(97), off(98), other(99), not-available(100)  

tsTimeslot26 1.3.6.1.4.1.760.1.1.2.1.10.701.4.1.326
This entry defines the port number used for the transmission of time slot 26. 'port-4' is available only if IportPortmode is set to 'interface-mode'. If the time slot is assigned for remote management (see mdmRemoteAccessMode). Valid for E1 units only.
OBJECT-TYPE    
  INTEGER port-1(1), port-2(2), port-3(3), port-4(4), remote-access(97), off(98), other(99), not-available(100)  

tsTimeslot27 1.3.6.1.4.1.760.1.1.2.1.10.701.4.1.327
This entry defines the port number used for the transmission of time slot 27. 'port-4' is available only if IportPortmode is set to 'interface-mode'. If the time slot is assigned for remote management (see mdmRemoteAccessMode). Valid for E1 units only.
OBJECT-TYPE    
  INTEGER port-1(1), port-2(2), port-3(3), port-4(4), remote-access(97), off(98), other(99), not-available(100)  

tsTimeslot28 1.3.6.1.4.1.760.1.1.2.1.10.701.4.1.328
This entry defines the port number used for the transmission of time slot 28. 'port-4' is available only if IportPortmode is set to 'interface-mode'. If the time slot is assigned for remote management (see mdmRemoteAccessMode). Valid for E1 units only.
OBJECT-TYPE    
  INTEGER port-1(1), port-2(2), port-3(3), port-4(4), remote-access(97), off(98), other(99), not-available(100)  

tsTimeslot29 1.3.6.1.4.1.760.1.1.2.1.10.701.4.1.329
This entry defines the port number used for the transmission of time slot 29. 'port-4' is available only if IportPortmode is set to 'interface-mode'. If the time slot is assigned for remote management (see mdmRemoteAccessMode). Valid for E1 units only.
OBJECT-TYPE    
  INTEGER port-1(1), port-2(2), port-3(3), port-4(4), remote-access(97), off(98), other(99), not-available(100)  

tsTimeslot30 1.3.6.1.4.1.760.1.1.2.1.10.701.4.1.330
This entry defines the port number used for the transmission of time slot 30. 'port-4' is available only if IportPortmode is set to 'interface-mode'. If the time slot is assigned for remote management (see mdmRemoteAccessMode). Valid for E1 units only.
OBJECT-TYPE    
  INTEGER port-1(1), port-2(2), port-3(3), port-4(4), remote-access(97), off(98), other(99), not-available(100)  

tsTimeslot31 1.3.6.1.4.1.760.1.1.2.1.10.701.4.1.331
This entry defines the port number used for the transmission of time slot 31. 'port-4' is available only if IportPortmode is set to 'interface-mode'. If the time slot is assigned for remote management (see mdmRemoteAccessMode). Valid for E1 units only.
OBJECT-TYPE    
  INTEGER port-1(1), port-2(2), port-3(3), port-4(4), remote-access(97), off(98), other(99), not-available(100)